mediatek: allow mounting ubifs by its device and partition name

Since not every device sets an ubifs partition name as the same as their
parent mtd partition, this change allows mount_ubi_part to usable in
other devices

Signed-off-by: Yonghyu Ban <yhban@silicon.moe>
Link: https://github.com/openwrt/openwrt/pull/19203
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mediatek: add Huasifei WH3000 Pro support

**Huasifei WH3000 Pro**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC. MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ with 5G modems module and PWM Fan.

**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1

**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.

**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.

**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-pro-squashfs-sysupgrade.bin
```

**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```

Cherry-picked from https://github.com/coolsnowwolf/lede/commit/949d0bd77a2e97c2d982531f72b76c575fb28839

Fixed `green` to `blue` LED in dts, added `SUPPORTED_DEVICES += huasifei,fudy-pro` - to make sysupgrade compatible with factory QWRT/Lede fork firmware.

Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19315
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 6.12 to 6.12.37

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.12.37

Manually rebased patch:
  generic/hack-6.12/902-debloat_proc.patch[1]

New Kconfig symbol:
  x86: enable MITIGATION_TSA[2]

All other patches are automatically refreshed.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.37&id=ead91de35d9cd5c4f80ec51e6020f342079170af
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.37&id=7a0395f6607a5d01e2b2a86355596b3f1224acbd

Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19317
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 6.6 to 6.6.97

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.97

Remove upstream patch:
  generic/backport-6.6/001-powerpc-kernel-Fix-pcc_save_regs-inclusion.patch[1]

Manually rebased patch:
  bcm53xx/patches-6.6/180-usb-xhci-add-support-for-performing-fake-doorbell.patch[2]

All other patches are automatically refreshed.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.97&id=8a7ac2737211451b8b98657b919c4c4e0a4c0c2f
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.97&id=7609899eb6b70b536123eb58eeab27c764752b82

Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Co-authored-by: John Audia <therealgraysky@proton.me>
Tested-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19317
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 6.12 to 6.12.36

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.12.36

Remove upstream patches:
  generic/backport-6.12/780-09-v6.13-r8169-add-support-for-RTL8125D.patch[1]
  generic/backport-6.12/781-04-v6.13-net-phy-realtek-merge-the-drivers-for-internal-NBase.patch[2]
  generic/backport-6.12/781-05-v6.13-net-phy-realtek-add-RTL8125D-internal-PHY.patch[3]

All other patches are automatically refreshed.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.36&id=37cb5967bd2513416398ff1a87a5ee2e63270b00
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.36&id=5eb0b10eea271e2e1f7d4fa1a6af6c09b2ecc4f5
[3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.36&id=5d479182d4ccde76df830a72927b3bdaafd142bf

Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Tested-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19317
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 6.6 to 6.6.96

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.96

Remove upstream patch:
  generic/pending-6.6/650-Revert-ipv6-save-dontfrag-in-cork.patch[1]

All other patches are automatically refreshed.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.96&id=c46358d0275953b27c3d86f7a224e229f2d57d05

Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Tested-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19317
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

uboot-tools: update to v2025.07

Update to the latest version.

Remove upstreamed patches:
  010-image-fit-sig-skip-in-tools-build-if-key-is-missing.patch[1]
  011-tools-fit_check_sign-make-key-optional.patch[2]
  012-tools-fit_check_sign-no-libcrypto.patch[2]

[1] https://github.com/u-boot/u-boot/commit/40dcd5088b7f64ee2841c233c8ab82ce9c188d73
[2] https://github.com/u-boot/u-boot/commit/9c79c8fe70da7cd05fa4c242197f14122f245d81

Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19342
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

tools/7z: update to 25.00

Changelog: https://www.7-zip.org/history.txt

All patches are automatically refreshed.

Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19360
Signed-off-by: Nick Hainke <vincent@systemli.org>

dropbear: disable RSA-SHA1 by default

Upstream has disabled SHA-1 algorithms by default since version 2025.87.
SHA-1 has known weakness and most SSH implementations support alternatives.

Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>

dropbear: simplify rebuild on config changes

It's hard or even impossible to track affected sources
so it's safe to remove all built objects (if any).

Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>

dropbear: refactor configuration

This allows to fine-tune dropbear build options.

This change is heavily based on similar work done by Marius Dinu earlier
so I'd like to say many thanks to original author.

Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>

dropbear: bump to 2025.88

- update dropbear to latest stable 2025.88;
  for the changes see https://matt.ucc.asn.au/dropbear/CHANGES
- rewrite 100-pubkey_path.patch
- refresh remaining patches

Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>

realtek: enhance RTL930x SerDes/PLL/CMU interoperability

The operating mode of a SerDes must be aligned with the attached PHY or
SFP module. That does not only require to change the protocol (e.g. SGMII,
10Gbase-R, ...) but also the speed (e.g. 1.25G). For this the SerDes must
be re-initialized properly.

- It must be taken into power down
- The PLL speed must be set
- Maybe the CMU (clock management unit) must be resetted
- The new mode must be set
- The state machine must be resetted
- The power must be reactivated

Until now this sequence is bugged. First the driver relies on a clean
setup from U-Boot (rtk network on) and second trying to to change mode
and PLL speeds does not work at all. And not to forget: Currently two
adjacent SerDes cannot drive SGMII/HSGMII at the same time. Fix this by
taking care about the right SerDes/PLL/CMU command init order.

P.S. This code is inspired by the work of Jan Hofmann, who tried to
enable parallel SGMII/HSGMII mode. The only missing bit was a proper CMU
reset sequence.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19220
Signed-off-by: Robert Marko <robimarko@gmail.com>

wifi-scripts: correctly set basic-rates with wpa_supplicant

Correctly load the list of basic_rates from UCI. basic-rates shall be
stored as a option-list. The current code did not retrieve this list
correctly.

wpa_supplicant uses a different config option to set basic-rates
when operating in mesh-mode.

Use the correct config key and calculation for mesh-interfaces.

Signed-off-by: David Bauer <mail@david-bauer.net>

perf: disable shellcheck

Since upstream commit:
b809fc656e763296f227b9b31e8f225e5977a8af ("perf build: Shellcheck support
for OUTPUT directory")

perf will attempt to run shellcheck on the test shell scripts, however
there is no point in doing this in OpenWrt and while perf checks for
shellcheck presence on your host it can fail to build in some cases.

So, simply disable it for now.

Link: https://github.com/openwrt/openwrt/pull/19361
Signed-off-by: Robert Marko <robimarko@gmail.com>

perf: disable BUILD_BPF_SKEL

BUILD_BPF_SKEL was set to 1 by default in upstream commit:
9925495d96efc14d885ba66c5696f664fe0e663c ("perf build: Default
BUILD_BPF_SKEL, warn/disable for missing deps")

Prior to that, it was disabled by default and you had to enable it to
build BPF skeleton support.

So in order to fix perf compilation with kernel 6.12, lets disable
BUILD_BPF_SKEL.

Fixes: #19310
Link: https://github.com/openwrt/openwrt/pull/19361
Signed-off-by: Robert Marko <robimarko@gmail.com>

unetd: update to Git HEAD (2025-07-05)

790b41b6b987 pex: indicate refused update requests
8b100a9e311a host: add support for defining per-host metadata

Signed-off-by: Felix Fietkau <nbd@nbd.name>

cli: add json data type

Signed-off-by: Felix Fietkau <nbd@nbd.name>

linux-firmware: update to 20250708

% git log --no-merges --pretty=oneline --abbrev-commit 20250627...20250708
74d80fcf8ce2 xe: Add fan_control v203.0.0.0 for BMG
331eac914440 linux-firmware: Update AMD cpu microcode
847cd5aaabe0 amdgpu: Add DCN 3.6
5e95c44fb4a7 amdgpu: Add PSP 14.0.5
520262d1d0a8 amdgpu: Add SDMA 6.1.3
84f443352785 amdgpu: Add GC 11.5.3
1f861a48042a mediatek MT7921: update bluetooth firmware to 20250625154126
d3e7e025210a qcom/adreno: document firmware revisions
4e7094412cd2 qcom/adreno: move A610 and A702 ZAP files to Adreno driver section
ed3c42722a02 qcom: Add sdx61 Foxconn vendor firmware image file
f534fd76aaa8 Revert "linux-firmware: Update firmware file for Intel Pulsar core"
ce7108f47ef6 qcom/adreno: sort entries in WHENCE
0ef7a160552a xe: First HuC release for Pantherlake
bbe12d522f4e xe: First GuC release for Pantherlake
5cf85776762a linux-firmware: update firmware for MT7921 WiFi device
78478bfc4431 rtw89: 8922a: update fw to v0.35.80.0
4e34a870bdb8 rtw89: 8852c: update fw to v0.27.129.1
4729093efd12 rtw89: 8852c: update fw to v0.27.128.0

Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc (Intel N150-based system)

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19352
Signed-off-by: Nick Hainke <vincent@systemli.org>

ath79: revert wmac node names

Changing the node names arbitrarily broke existing configurations, which
rely on the device path in /etc/config/wireless.
Revert that part of the change without altering the compatible strings.

Fixes: 7e09959efda2 ("mac80211: fix wmac node names")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

kernel: fix rtl8261n driver for realtek

The RTL8261N driver does not work correctly on non-mediatek devices. Remove
some of the power controls for Realtek chips.

This assumes the network has been started by the bootloader already:
(rtk network on).

Co-authored-by: Sebastian Gottschall
- https://github.com/mirror/dd-wrt/commit/bf45143f03d40bf259d34bba2151aab46ee011f4
- https://github.com/mirror/dd-wrt/commit/2fb02a5745bb538124a7467b399930b5ca79e71d
- https://github.com/mirror/dd-wrt/commit/598a16a8d801869e09c033f8ca35534289d393cf
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19081
Signed-off-by: Robert Marko <robimarko@gmail.com>

kernel: support RTL8264 in rtl8261n driver

Add support for the RTL8264 (quad-10G phy) by matching the appropriate PHY_ID
in the driver.

Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19081
Signed-off-by: Robert Marko <robimarko@gmail.com>

hostapd: ignore comment lines for hash comparison

Fixes spurious unnecessary bss restarts

Signed-off-by: Felix Fietkau <nbd@nbd.name>

Revert "ncurses: update to 6.5"

This reverts commit 8876192bff497bfda6cbfbbdf29e6cfb3584cc82.

This broke ncurses host build for me, and thus ncurses in general.

Signed-off-by: Robert Marko <robimarko@gmail.com>

octeon: ubnt-*: Add device specific DTS pruning

This imports device specific DTS pruning from
https://github.com/UI-Packages/kernel_e200/blob/master/arch/mips/cavium-octeon/octeon-platform.c#L1067

- Reduce MMC clock frequency on E200/E220 to make
  MMC communication reliable again. See linked issue.
- Remove unused MMC node on E300.

Link: https://github.com/openwrt/openwrt/issues/13762
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Link: https://github.com/openwrt/openwrt/pull/19229
Signed-off-by: Robert Marko <robimarko@gmail.com>

ncurses: update to 6.5

Update to 6.5.

Removed patch from pre-2012: 101-ncurses-5.6-20080628-kbs.patch

Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19335
Signed-off-by: Robert Marko <robimarko@gmail.com>

ncurses: Add -std=gnu17 to CFLAGS to avoid a GCC15 error when building with glibc

Without the newly introduced flag, building with libc ends in errors such the below.
There is an upstream fix[1], but backporting it is not straight forward.

/scratch/union/staging_dir/toolchain-x86_64_gcc-15.1.0_glibc/x86_64-openwrt-linux-gnu/include/c++/15.1.0/cstddef:81:21: error: redefinition of 'struct std::__byte_operand<unsigned char>'
   81 |   template<> struct __byte_operand<unsigned char> { using __type = byte; };
      |                     ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/scratch/union/staging_dir/toolchain-x86_64_gcc-15.1.0_glibc/x86_64-openwrt-linux-gnu/include/c++/15.1.0/cstddef:78:21: note: previous definition of 'struct std::__byte_operand<unsigned char>'
   78 |   template<> struct __byte_operand<bool> { using __type = byte; };
      |                     ^~~~~~~~~~~~~~~~~~~~
make[4]: *** [Makefile:438: ../obj_s/cursesp.o] Error 1

1. https://ncurses.scripts.mit.edu/?p=ncurses.git;a=commit;h=394a1a6cf317912584592e33184ef550e738a4b9

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19335
Signed-off-by: Robert Marko <robimarko@gmail.com>

xcrypt: work-around broken use of VARIANT with BUILDONLY

Split the xcrypt package build into two Makefiles and a common part for
the version definition in order to work-around build problems when
combining VARIANT with BUILDONLY and scoped InstallDev.

This is done in order to skip build of libcrypt-compat in case we are
not building against glibc in order to prevent libcrypt.so shared
library being present in staging_dir and by that breaking multiple
packages which then will link against it.

Fixes: e3cf7088f1 ("libcrypt-compat: introduce package")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/19353
Signed-off-by: Robert Marko <robimarko@gmail.com>

toolchain: gcc: 15: fix build error with glibc for aarch64 targets

GCC 14+ fails to build due to libatomic specific -march handling.
This build error triggers only with glibc and not with musl libc
which is default.

It seems that this patch from GCC14 was forgotten when GCC15 support was
being added [1].

[1] https://github.com/openwrt/openwrt/commit/44ef34350095c86227ea0cf84b816258c5195e29

Fixes: 68cb84183e38 ("toolchain: add support for GCC 15.1")
Signed-off-by: Robert Marko <robimarko@gmail.com>

mold: Update to 2.40.1

Update mold to 2.40.1

Release notes:
https://github.com/rui314/mold/releases/tag/v2.40.1
https://github.com/rui314/mold/releases/tag/v2.40.0

Signed-off-by: Carsten Schuette <schuettecarsten@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/19339
Signed-off-by: Robert Marko <robimarko@gmail.com>

tools/mkimage: update to v2025.07

Update to latest version. All patches are automatically refreshed.

Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19341
Signed-off-by: Nick Hainke <vincent@systemli.org>

libnftnl: update to 1.2.9

ChangeLog:

https://git.netfilter.org/libnftnl/log/?h=libnftnl-1.2.9

Signed-off-by: Antony Kolitsos <zeusomighty@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/19288
Signed-off-by: Nick Hainke <vincent@systemli.org>

nftables: update to 1.1.3

ChangeLog:

1.1.3: https://netfilter.org/projects/nftables/files/changes-nftables-1.1.3.txt
1.1.2: https://netfilter.org/projects/nftables/files/changes-nftables-1.1.2.txt

Signed-off-by: Antony Kolitsos <zeusomighty@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/19288
Signed-off-by: Nick Hainke <vincent@systemli.org>

ramips: update drivers to be compatible with kernel 6.12 and above

Replace .remove_new with .remove for compatibility with future kernel versions.
Dropping compatibility with older kernels.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19320
Signed-off-by: Nick Hainke <vincent@systemli.org>

ramips: drop 6.6 support

Drop configs and patches for Linux 6.6.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19320
Signed-off-by: Nick Hainke <vincent@systemli.org>

ramips: use kernel 6.12 by default

Switch to Linux kernel version 6.12.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19320
Signed-off-by: Nick Hainke <vincent@systemli.org>

mt76: update to Git HEAD (2025-07-07)

6df761e0e6c7 mt76: fix signature of platform_driver remove funtions for newer kernels
5724be1a6b12 wifi: mt76: Replace strlcpy() with strscpy()
c4a114e2b8c9 wifi: mt76: fix queue assignment for deauth packets
243e572d89fc wifi: mt76: add a wrapper for wcid access with validation
e41c7785589f wifi: mac80211: get tx power per link
d70f62b8f1c7 wifi: mt76: fix vif link allocation
7b3cd3274a24 wifi: mt76: mt7996: Fix secondary link lookup in mt7996_mcu_sta_mld_setup_tlv()
cf89b6218043 wifi: mt76: mt7996: Rely on for_each_sta_active_link() in mt7996_mcu_sta_mld_setup_tlv()
d71108eedab1 wifi: mt76: mt7996: Do not set wcid.sta to 1 in mt7996_mac_sta_event()
32f8c5849ed1 wifi: mt76: mt7996: Fix mlink lookup in mt7996_tx_prepare_skb
ffff9f71e29d wifi: mt76: mt7996: Fix possible OOB access in mt7996_tx()
afe63e758196 wifi: mt76: mt7996: Fix valid_links bitmask in mt7996_mac_sta_{add,remove}
68dd28b99dad wifi: mt76: mt7996: Add MLO support to mt7996_tx_check_aggr()
293778652452 wifi: mt76: mt7996: Move num_sta accounting in mt7996_mac_sta_{add,remove}_links
a94166b21e20 wifi: mt76: Get rid of dma_sync_single_for_device() for MMIO devices
87873d854e51 wifi: mt76: mt7925: Fix null-ptr-deref in mt7925_thermal_init()
06ba3d5e91f4 wifi: mt76: mt792x: Limit the concurrent STA and SoftAP to operate on the same channel
b9f4e0df317d wifi: mt76: mt792x: improve monitor interface handling
ec95319fd3fb wifi: mt76: mt7921s: Introduce SDIO WiFi/BT combo module card reset
dd2d862251cb firmware: add missing mt7990 eeprom files
05eaa56bc7a4 firmware: update mt7992 firmware to 20250328
32ca2b6db354 firmware: update mt7996 firmware to 20250328

Signed-off-by: Felix Fietkau <nbd@nbd.name>

mac80211: fix wmac node names

The upstream submission for this mandates the node to be named wifi
instead of wmac. Change all ath79 entries to match the new names and
remove the compatibility patch.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19328
Signed-off-by: Robert Marko <robimarko@gmail.com>

kernel: backport GCC15 fix for powerpc

Comes with kernel 6.16. I assume it will be backported at some point.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19329
Signed-off-by: Robert Marko <robimarko@gmail.com>

hostapd: enable CONFIG_OCV when 802.11be support is enabled

The 802.11be supoort code unconditionally calls ocv related functions

Signed-off-by: Felix Fietkau <nbd@nbd.name>

readline: update to 8.3

Needed to fix GCC 15 compilation with dependent packages.

Removed upstreamed patch.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19327
Signed-off-by: Robert Marko <robimarko@gmail.com>

ucode: fix an issue in exception handling improvement for ubus/uloop

Remove an uloop_end() call from a user cb that wasn't there before

Signed-off-by: Felix Fietkau <nbd@nbd.name>

ath9k: add back previous DT compatible strings for ahb

The ath9k ahb patch was updated to match the latest upstream version,
however the openwrt DT files still use the older names.
Add those as extra entries in order to remain compatible until DT files
are fixed.

Fixes: 88f4c32060f7 ("mac80211: update to version 6.14.11")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

hostapd: revert a broken upstream patch that was breaking multi-band operation

nl80211 events were propagated to the wrong interfaces

Fixes: 2ac791e87d3d ("hostapd: update to version 2025-06-27")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mac80211: fix rt2x00 build error on 6.12

Fix missing remove callback type signature conversion

Signed-off-by: Felix Fietkau <nbd@nbd.name>

image: only calculate EROFS_PCLUSTERSIZE when needed

Fixes shell warning on any makefile including image.mk when EROFS
is not enabled

Signed-off-by: Felix Fietkau <nbd@nbd.name>

kernel: fix fraglist GRO on linux 6.12

Merged segments had a broken skb network header offset.

Fixes: https://github.com/openwrt/openwrt/issues/19130
Signed-off-by: Felix Fietkau <nbd@nbd.name>

image: add support for EROFS rootfs image generation

Add support for generating EROFS rootfs images.

The EROFS filesystem can offer competitive I/O performance while
minimizing final image size when using the MicroLZMA compressor.

Target platform: linux-x86_generic (target-i386_pentium4_musl)

Filesystem     Image Size
=============  ==========
root.erofs     4882432
root.ext4      109051904
root.squashfs  4903302

Co-Developed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://github.com/openwrt/openwrt/pull/19244
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

tools: add erofs-utils

Add erofs-utils to create an EROFS-based rootfs for image generation.

Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://github.com/openwrt/openwrt/pull/19244
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

fstools: update to Git HEAD (2025-07-05)

e8cd820cdbb8 libfstools: add support for EroFS based images

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

hostapd: removed OSU support from configuration files, it was removed in the last hostapd update.

Ref: https://w1.fi/cgit/hostap/commit/hostapd?id=e835288592fd672469f46dc35a03e64115b996e5
Ref: https://w1.fi/cgit/hostap/commit/hostapd?id=7bb11e35d55e3d50199efc45921e76696bebd8ef

Fixes: https://github.com/openwrt/openwrt/issues/19142
Link: https://github.com/openwrt/openwrt/pull/19273
Signed-off-by: Agustin Lorenzo <agustin.lorenzo@thinco.es>

mediatek: fix switch mdio id on mt7622-rfb1 on linux 6.12

Signed-off-by: Felix Fietkau <nbd@nbd.name>

mac80211: update to version 6.14.11

Update to version 6.14.11

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

hostapd: update to version 2025-06-27

Manually refreshed:

140-tests-Makefile-make-run-tests-with-CONFIG_TLS.patch
601-ucode_support.patch

Fixed in upstream:

804-hostapd-revert-ACS-Validate-6-GHz-AP-criteria-before.patch [1]

Automatically rebased all other patches.

[1] https://w1.fi/cgit/hostap/commit/?id=0b60826a66885bffa2fd709ed5e48cd5fe241b6b

Signed-off-by: Agustin Lorenzo <agustin.lorenzo@thinco.es>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

hostapd: disable 802.11be support in the mini variant

802.11be capable platforms are big enough to not need the mini variant,
and removing it here saves space for other other devices.

Signed-off-by: Felix Fietkau <nbd@nbd.name>

hostapd: fix potential double free in ubus code

Ensure that the object name is never freed twice

Signed-off-by: Felix Fietkau <nbd@nbd.name>

wifi-scripts: ucode: fix iwinfo crash on untracked interfaces

Deal with data.radio being null

Signed-off-by: Felix Fietkau <nbd@nbd.name>

ucode: add patches to improve exception handling for ubus/uloop

Add API to allow setting an exception handler for user provided callbacks

Signed-off-by: Felix Fietkau <nbd@nbd.name>

mac80211: add WIFI_SCRIPTS_UCODE to PKG_CONFIG_DEPENDS

It affects package depdendencies

Signed-off-by: Felix Fietkau <nbd@nbd.name>

generic: 6.6: drop netdev backported patch for netdev_tx_reset_subqueue

Patch backporting netdev_tx_reset_subqueue new OP has been already
backported in recent minor kernel version for 6.6.

Drop the related patch to fix compilation error on 6.6.

Fixes: 34ba7e8a8ab1 ("generic: backport some flow offload helper patch")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

airoha: backport upstream patch for Flow Offload support for AN7581

Backpot upstream patch for Flow Offload support for AN7581 and refresh
all affected patch. To correctly work a dedicated firmware is needed to
use the dedicated Network Coprocessor (NPU).

This also introduce good cleanup and moves the driver in a dedicated
Airoha directory. While currently not totally usable (due to lack of
firmware blob) this is needed to backport support for external PHY/SFP
support.

Refresh all affected patch.

Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18166
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

airoha: backport minor fixes for ethernet driver

Backport some upstream patch for Airoha ethernet driver in preparation
for Flow Offload support.

Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18166
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

generic: backport some flow offload helper patch

Backport some flow offload helper patch in preparation for Airoha Flow
Offload support.

Link: https://github.com/openwrt/openwrt/pull/18166
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

airoha: replace PCIe patch with upstream version

Replace PCIe patch with upstream version and update DTS with new PBUS
CSR property now required.

Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18166
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

ramips: fix wifi nodes to upstream standards

Replaced all mt76@ with wifi@ per upstream requirement for all wifi
nodes.

Added missing compatible string where appropriate as stated by mt76.yaml
upstream.

Also updated reg value to be consistent everywhere.

Replace all pci14c3 entries to use mediatek,mt76.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19067
Signed-off-by: Robert Marko <robimarko@gmail.com>

config: drop kernel config symbols removed before v6.6

Since we don't support any kernel versions below v6.6, Kconfig options
that were removed upstream before 6.6 are no longer relevant and should be
dropped.

This commit removes the following obsolete kernel config options:
- KERNEL_UBSAN_NULL: Removed in v4.18 (3ca17b1f3628)
- KERNEL_DEBUG_LL_UART_NONE: Removed in v4.0 (6f5194553c84)
- KERNEL_SLABINFO: Removed in v4.15 (5b36577109be)
- KERNEL_RESOURCE_COUNTERS: Removed in v3.18 (5b1efc027c0b)
- KERNEL_MM_OWNER: Removed in v3.16 (f98bafa06a28)
- KERNEL_MEMCG_SWAP: Removed in v6.1 (e55b9f96860f)
- KERNEL_MEMCG_SWAP_ENABLED: Removed in v5.7 (2d1c498072de)
- KERNEL_DEVPTS_MULTIPLE_INSTANCES: Removed in v4.7 (eedf265aa003)
- KERNEL_DEVKMEM: Removed in v5.13 (bbcd53c96071)
- KERNEL_SECURITY_SELINUX_DISABLE: Removed in v6.4 (f22f9aaf6c3d)

Signed-off-by: Harrison Boyd <harrisonboyd400@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19287
Signed-off-by: Robert Marko <robimarko@gmail.com>

libnetfilter-conntrack: bump to 1.1.0

Updates libnetfilter-conntrack to version 1.1.0.
Removes patches which should no longer be needed according to changelog for
libnetfilter-conntrack 1.1.0

Signed-off-by: Ian Ladd <ianwladd@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19282
Signed-off-by: Robert Marko <robimarko@gmail.com>

uboot-mediatek: force update_cache_variants to use reset for Foresee NAND

Force update_cache_variantsvariants to use reset for Foresee NAND with bad blocks.

Tested on Xiaomi AX3000T + F35SQA001G with bad blocks and without bad blocks

Signed-off-by: Dim Fish <dimfish@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17963
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

mediatek: spinand: force update_cache_variants to use reset for Foresee NAND

Force update_cache_variantsvariants to use reset for Foresee NAND with bad blocks.

Tested on Xiaomi AX3000T + F35SQA001G with bad blocks and without bad blocks

Signed-off-by: Dim Fish <dimfish@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17963
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

usbgadget: bump PKG_RELEASE for os descriptors support

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

mbedtls: update to 3.6.4

This release includes fixes for security issues.

Mbed TLS 3.6 is a long-term support (LTS) branch. It will be supported with bug-fixes and security fixes until at least March 2027.

Security Advisories

For full details, please see the following links:

    Race condition in AESNI support detection [1]
    Heap buffer under-read when parsing PEM-encrypted material [2]
    Unchecked return value in LMS verification allows signature bypass [3]
    Out-of-bounds read in mbedtls_lms_import_public_key() [4]
    Timing side-channel in block cipher decryption with PKCS#7 padding [5]
    NULL pointer dereference after using mbedtls_asn1_store_named_data() [6]
    Misleading memory management in mbedtls_x509_string_to_names() [7]

[1] https://mbed-tls.readthedocs.io/en/latest/security-advisories/mbedtls-security-advisory-2025-06-1/
[2] https://mbed-tls.readthedocs.io/en/latest/security-advisories/mbedtls-security-advisory-2025-06-2/
[3] https://mbed-tls.readthedocs.io/en/latest/security-advisories/mbedtls-security-advisory-2025-06-3/
[4] https://mbed-tls.readthedocs.io/en/latest/security-advisories/mbedtls-security-advisory-2025-06-4/
[5] https://mbed-tls.readthedocs.io/en/latest/security-advisories/mbedtls-security-advisory-2025-06-5/
[6] https://mbed-tls.readthedocs.io/en/latest/security-advisories/mbedtls-security-advisory-2025-06-6/
[7] https://mbed-tls.readthedocs.io/en/latest/security-advisories/mbedtls-security-advisory-2025-06-7/

Signed-off-by: Antony Kolitsos <zeusomighty@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/19291
Signed-off-by: Robert Marko <robimarko@gmail.com>

usbgadget: add OS descriptors support

Add OS descriptors support. Configuring OS descriptors allows Microsoft
Windows to bind the right drivers without any additional configuration.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19237
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

openssl: update to 3.5.1

Automatically rebased: 100-Configure-afalg-support.patch

Changes between 3.5.0 and 3.5.1:
Fix x509 application adds trusted use instead of rejected use.
Issue summary: Use of -addreject option with the openssl x509 application
adds a trusted use instead of a rejected use for a certificate.

Impact summary: If a user intends to make a trusted certificate rejected
for a particular use it will be instead marked as trusted for that use.
(CVE-2025-4575)

Aligned the behaviour of TLS and DTLS in the event of a no_renegotiation
alert being received. Older versions of OpenSSL failed with DTLS if a
no_renegotiation alert was received. All versions of OpenSSL do this for TLS.
From 3.2 a bug was exposed that meant that DTLS ignored no_rengotiation.
We have now restored the original behaviour and brought DTLS back into line
with TLS.

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19283
Signed-off-by: Robert Marko <robimarko@gmail.com>

imagebuilder: implement STRIP_ABI option for manifest target

When using apk as the package manager, imagebuilder make command

    make manifest STRIP_ABI=1

does not strip package names of their ABI-version suffix.  The ASU
server relies on this to validate builds, so many snapshot build
requests are failing.

Fix this by using the already existing package data parser in
make-index-json.py and augment it to write the result in manifest
format.

Fixes: https://github.com/openwrt/openwrt/issues/19274
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19278
Signed-off-by: Robert Marko <robimarko@gmail.com>

realtek: add RTL931x support to rt-loader

The RTL931x devices have an other register that describes the
current RAM configuration. Enhance the identification routine.

Tested on LGS352C (RTL9311).

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19284
Signed-off-by: Robert Marko <robimarko@gmail.com>

tools/squashfs4: fix compile on Alpine Linux

This backports upstream commit 05a895b3f996[1] to fix
compilation when using musl on the host machine.

[1]: https://github.com/plougher/squashfs-tools/commit/05a895b3f996d1ac157d95b04980f5f047e7dbf7

Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/19285
Signed-off-by: Robert Marko <robimarko@gmail.com>

ubus: update to Git HEAD (2025-07-02)

5952b48e251c ubusd: do not call socket callback from ubus_msg_send

Signed-off-by: Felix Fietkau <nbd@nbd.name>

util-linux: update to v2.41.1

Release Notes:
https://www.kernel.org/pub/linux/utils/util-linux/v2.41/v2.41.1-ReleaseNotes

Remove upstreamed:
0001-meson-add-feature-for-translated-documentation.patch
0001-meson-remove-tinfo-dependency-from-more.patch
0100-include-linux-unistd-h.patch

Signed-off-by: Thomas Weißschuh <thomas@t-8ch.de>
Link: https://github.com/openwrt/openwrt/pull/19236
Signed-off-by: Nick Hainke <vincent@systemli.org>

tools: util-linux: update to v2.41.1

Release Notes:
https://www.kernel.org/pub/linux/utils/util-linux/v2.41/v2.41.1-ReleaseNotes

Remove upstreamed:
tools/util-linux/patches/101-macos-weak-aliases.patch

Signed-off-by: Thomas Weißschuh <thomas@t-8ch.de>
Link: https://github.com/openwrt/openwrt/pull/19236
Signed-off-by: Nick Hainke <vincent@systemli.org>

rockchip: switch to kernel 6.12

Switch to kernel 6.12 and remove kernel 6.6 files.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19259
Signed-off-by: Nick Hainke <vincent@systemli.org>

ubus: update to Git HEAD (2025-07-01)

27839f854a58 ubusd: make txq_len field signed
b35b2bc63e8e ubusd: treat EACCES on write like EAGAIN
713e9d19b2b6 ubusd: retry write on EINTR
8bb523ab20e0 ubusd: fix txq_len accounting
b1b783c74742 ubusd: add another tx attempt on enqueueing the first message for a client

Signed-off-by: Felix Fietkau <nbd@nbd.name>

u-boot.mk: support Python 3.12 and 3.13

Fixes the following build problem on systems with Python 3.12 or 3.13:

Checking 'python3-setuptools'... failed.
Checking 'swig'... ok.

u-boot: Please install the Python3 setuptools module

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

qualcommax: ipq50xx: Add support for Yuncore AX830

Specifications:
SOC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
Memory: 512MB DDR3L
Standard: 802.11ax/ac/b/g/n
Flash: SPI NOR 8MB (Winbond W25Q64DW) + NAND 128MB (Winbond W25N01GWZEIG)
2.4G Frequency: 2.4GHz - 2.484GHz
2.4G Wi-Fi standard: 802.11b/g/n/ax
5.8G Frequency: 4.9~5.9G
5.8G Wi-Fi Standard: 802.11 a/n/ac/ax
Interface:
  Optional 1(Without 8081):
    1 * 10/100 /1000Mbps RJ45 WAN Port and PoE port;
    1* Gigabit Console port;
  Optional 2(With 8081):
    1 * 10/100/1000/2500Mbps RJ45 WAN port and PoE port,
    1*10/100/1000Mbps LAN port
Buttons: 1 * Reset button, press 10 seconds to revert to default setting
Antenna: Build in 4*4dBi dual band MIMO Antenna
Data Rate: 3000Mbps （2.4G 600Mbps, 5.8G 2400Mbps）
End Users: 128+
2.4G RF Power: ≤ 23dBm
5.8G RF Power: ≤ 23dBm
DC: 12V----2A
PoE: 48V (IEEE 802.3at)
LED Light: Sys, WAN, LAN
Power Consumption: ≤ 20W

BACKUP YOUR STOCK FIRMWARE:
- Put openwrt-*-initramfs-uImage.itb to your
  TFTP server and rename it to initramfs.bin
- Enable serial console and enter to u-boot cli
  and exec these commands:
    ```
    tftpboot <your_tftp_server_ip>:initramfs.bin
    bootm
    ```
- Once boot completed and you get the openwrt shell
  execute below commands:
    ```
    device=ax830
    mkdir -p /tmp/fw_backup; cd /tmp/fw_backup
    rootfs=$(cat /proc/mtd | grep \"rootfs\" | cut -d: -f1)
    rootfs_1=$(cat /proc/mtd | grep \"rootfs_1\" | cut -d: -f1)
    dd if=/dev/${rootfs} of=rootfs_${rootfs} bs=1M
    dd if=/dev/${rootfs_1} of=rootfs_1_${rootfs_1} bs=1M
    cp /sys/firmware/fdt fdt.dtb
    md5sum * > md5sum
    tar -cvzf /tmp/${device}.tar.gz .
    sum=$(md5sum /tmp/${device}.tar.gz | cut -d' ' -f1)
    mv /tmp/${device}.tar.gz /tmp/${device}_${sum}.tar.gz
    echo "stock fw backup saved to: /tmp/${device}_${sum}.tar.gz"
    ```
- Upload/save your backup to a safe place.

STOCK FIRMWARE RECOVERY:
- Boot initramfs image
- Upload your backed-up stock fw tarball to the device
  using scp or download it from the device using wget.
- Enter device ssh cli or tty and exec:
    ```
    cd /tmp && wget <your_web_server_ip>/${stock_fw_backup}.tar.gz`
    tar -xpzf ${stock_fw_backup}.tar.gz
    rootfs=$(cat /proc/mtd | grep \"rootfs\" | cut -d: -f1)
    rootfs_1=$(cat /proc/mtd | grep \"rootfs_1\" | cut -d: -f1)
    ubiformat /dev/${rootfs} -y -f /tmp/rootfs_${rootfs}
    ubiformat /dev/${rootfs_1} -y -f /tmp/rootfs_1_${rootfs_1}
    reboot
    ```

INSTALLATION:
1. initramfs method
- Put openwrt-*-initramfs-uImage.itb to your
  TFTP server and rename it to initramfs.bin
- Enable serial console and enter to u-boot cli
  and exec these commands:
    ```
    tftpboot <your_tftp_server_ip>:initramfs.bin
    bootm
    ```
- Once boot completed and you get the openwrt shell
  execute below commands:
    ```
    cd /tmp && wget <your_web_server_ip>/factory.ubi`
    export rootfs=$(cat /proc/mtd | grep rootfs | cut -d: -f1)
    export rootfs_1=$(cat /proc/mtd | grep rootfs_1 | cut -d: -f1)
    ubiformat /dev/${rootfs} -y -f factory.ubi
    ubiformat /dev/${rootfs_1} -y -f factory.ubi
    reboot
    ```

2. u-boot factory.ubi image method
- Put factory.ubi to your TFTP server and
  enter u-boot cli and exec these commands:
    ```
    tftpboot <your_tftp_server_ip>:factory.ubi
    #After downloading is finished:
    flash rootfs
    flash rootfs_1
    reset
    ```

Signed-off-by: Shubham Vishwakarma <shubhamvis98@fossfrog.in>
Link: https://github.com/openwrt/openwrt/pull/18968
Signed-off-by: Robert Marko <robimarko@gmail.com>

ipq-wifi: update to Git HEAD (2025-06-23)

63bd0faafd4a Add IPQ5018 BDF for Yuncore AX830.

Link: https://github.com/openwrt/openwrt/pull/18968
Signed-off-by: Robert Marko <robimarko@gmail.com>

download: improve rawgit tar reliability

Packages that depend on rawgit can fail on systems with the tar UID
issue (https://bugzilla.redhat.com/show_bug.cgi?id=913406).
Fix this by adding tar flags to overwrite UID/GID, as in the
dl_tar_pack method.

Signed-off-by: Ondrej Cierny <o.cierny@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19243
Signed-off-by: Robert Marko <robimarko@gmail.com>

linux-firmware: update to 20250627

% git log --no-merges --pretty=oneline --abbrev-commit 20250613...20250627
cb826c70e912 WHENCE: extract license texts
db6e24385793 WHENCE: expand the advansys license statement
e8a4acb51210 WHENCE: some older AMD drivers are MIT licensed
ebbcfe361cbf qcom: update firmware binary for SM8550
09db581815f8 amdgpu: DMCUB updates for DCN401
c319d6bea7a6 qcom: venus-5.4: add the firmware binary for qcs615
dbfe16e9e8ac Revert "qcom: Add sdx61 Foxconn vendor firmware image file"
cbbce56d6dcc amdgpu: update dmcub fw for dcn401
8c091f4b0ec5 qcom: Add sdx61 Foxconn vendor firmware image file
1c4846b614e0 brcm: Fix symlinks for Khadas VIM SDIO wifi config
f191695a00ba amdgpu: update renoir firmware
c71a6daecc53 amdgpu: update vcn 5.0.0 firmware
72a8d25438c0 amdgpu: update smu 14.0.3 firmware
9f33f83a3245 amdgpu: update sdma 7.0.1 firmware
ef19800204dd amdgpu: update psp 14.0.3 firmware
103e235bafd0 amdgpu: update gc 12.0.1 firmware
f69dbbbd61b1 amdgpu: update navy flounder firmware
839067097384 amdgpu: update psp 14.0.4 firmware
0fde9638f26e amdgpu: update gc 11.5.2 firmware
128b759e5c8f amdgpu: update sienna cichlid firmware
94e718de8906 amdgpu: add raven2 ip discovery firmware
cbd24c08ceff amdgpu: update smu 14.0.2 firmware
fe7f99e3d01b amdgpu: update sdma 7.0.0 firmware
20e709912411 amdgpu: update psp 14.0.2 firmware
0e6cf73ebe2a amdgpu: update gc 12.0.0 firmware
00ce8ee06be2 amdgpu: update vcn 4.0.6 firmware
ed9525cb5743 amdgpu: update psp 14.0.1 firmware
cd7f739592db amdgpu: update gc 11.5.1 firmware
56accbf3cc71 amdgpu: update psp 13.0.11 firmware
03523034b0a5 amdgpu: update gc 11.0.4 firmware
1035014812d6 amdgpu: add picasso ip discovery firmware
7e14bde8ffdf amdgpu: add raven ip discovery firmware
2427860b84e9 amdgpu: update vega20 firmware
c354a0967253 amdgpu: update vega12 firmware
6e36b3917519 amdgpu: update smu 13.0.7 firmware
97e3e9cb4d96 amdgpu: update vcn 4.0.4 firmware
52f8bb5fd748 amdgpu: update psp 13.0.7 firmware
b2f81cf8dd1d amdgpu: update gc 11.0.2 firmware
46646de90c81 amdgpu: update navi14 firmware
6d59ec7d67dd amdgpu: update vega10 firmware
6a451a89f175 amdgpu: update gc 10.3.6 firmware
aa3e04655f08 amdgpu: update smu 13.0.10 firmware
97c3f575f445 amdgpu: update psp 13.0.10 firmware
c58be58dc9b4 amdgpu: update gc 11.0.3 firmware
403f1c578204 amdgpu: update navi12 firmware
a21004dd4edb amdgpu: update vangogh firmware
d45a9e3e51f5 amdgpu: update navi10 firmware
c70bcef9759d amdgpu: add smu 13.0.0 kicker firmware
c5077ee16e2c amdgpu: add psp 13.0.0 kicker firmware
25fbfc9a9fe6 amdgpu: add gc 11.0.0 kicker firmware
9fff2b17d3b1 amdgpu: add vcn 5.0.1 firmware
fea4ac9c76cb amdgpu: add sdma 4.4.4 firmware
8a9e3b47ef3d amdgpu: add psp 13.0.12 firmware
41e2f753b3a7 amdgpu: add gc 9.5.0 firmware
38945107950a amdgpu: add arcturus IP discovery firmware
49447aed4821 amdgpu: update vcn 4.0.0 firmware
734cc9b82e60 amdgpu: update smu 13.0.0 firmware
36934f24c008 amdgpu: update psp 13.0.0 firmware
464402529b3f amdgpu: update gc 11.0.0 firmware
1f9ea1b74498 amdgpu: update psp 13.0.14 firmware
877eed711964 amdgpu: update gc 9.4.4 firmware
a4a2882f0391 amdgpu: update psp 13.0.6 firmware
49105d8ee7e1 amdgpu: update gc 9.4.3 firmware
976433406ee3 amdgpu: update beige_goby firmware
3073095c049f amdgpu: update vcn 4.0.5 firmware
f2f8b021e7ca amdgpu: update gc 11.5.0 firmware
ad90939ad7a8 amdgpu: update vcn 4.0.2 firmware
6937d2e155c9 amdgpu: update gc 11.0.1 firmware
00198a7ab7a8 amdgpu: update dimgrey_cavefish firmware
95f5f3cc1044 amdgpu: update aldebaran firmware
b8369884e1db WHENCE: fix subtly incorrect licensing
a26e413e7481 amdgpu: update dmcub fw for dcn32 and dcn401
3c5341f382e0 mediatek: Update mt8186 SCP firmware
9096bad65cb9 amdgpu: Update DMCUB fw for DCN401 & DCN315
0a0b23e207c9 WHENCE: unify Driver statements
4cb2b59c30c2 qcom: add gpu firmwares for X1P42100 chipset

Build system: x86/64
Build-tested: x86/64
Run-tested: x86/64

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19251
Signed-off-by: Robert Marko <robimarko@gmail.com>

realtek: rt-loader bootbase device enhancement

Until now the rt-loader only works on U-Boot driven devices where the
environment (e.g. coprocessor) is usually setup properly. Devices like
the ZyXEL GS1920 series use BootBase as start environment and skip
some of the basic initialization steps. rt-loader will fail in these
cases. Take care about the CP0 registers.

Additionally enhance the documentation of the printf implementation.
It was optimized during the different revisions of the initial PR.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19253
Signed-off-by: Robert Marko <robimarko@gmail.com>

x86: 64: Enable PCI MMCONFIG

Some devices can't boot since kernel 6.6 without PCI MMCONFIG.

Fixes: https://github.com/openwrt/openwrt/issues/18228
Fixes: https://forum.openwrt.org/t/openwrt-24-10-x86-64-boot-hangs-after-pci-nvme-initialization/229086
Signed-off-by: Kazuhiro Ito <kzhr@d1.dion.ne.jp>
Link: https://github.com/openwrt/openwrt/pull/19256
Signed-off-by: Robert Marko <robimarko@gmail.com>

kernel: allow seamless migration from I40EVF

Resolve the issue of seamless migration from I40EVF
link: https://github.com/openwrt/openwrt/pull/19197/files#r2173571237
Signed-off-by: xiao bo <peterwillcn@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19255
Signed-off-by: Robert Marko <robimarko@gmail.com>

kernel: bump 6.6 to 6.6.95

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.95

Removed upstreamed:
 backport-6.6/201-v6.16-mips-Add-std-flag-specified.patch[1]
 mvebu/patches-6.6/0004-v6.16-pinctrl-armada-37xx-propagate-error-from-armada_37xx.patch[2]
 mvebu/patches-6.6/0005-v6.16-pinctrl-armada-37xx-propagate-error-from-armada_37xx.patch[3]
 mvebu/patches-6.6/0006-v6.16-pinctrl-armada-37xx-propagate-error-from-armada_37xx.patch[4]
 mvebu/patches-6.6/0007-v6.16-pinctrl-armada-37xx-propagate-error-from-armada_37xx.patch[5]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.95&id=231f6a1de15b3f62eb8d6163a8b1bc5935025c69
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.95&id=ae48bc0b8be8786fd0ceab4b5a95c09b5aa93816
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.95&id=8a15a5438c5816a1003b88ce20f25ccc92909ee7
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.95&id=02c966a8869becb29282403540c88ba33e19c347
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.95&id=14a26f6692062a529b612420adb6c0b9290b25d3

Build system: x86/64
Build-tested: flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3, x86/64
Run-tested: flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3, x86/64

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19248
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 6.12 to 6.12.35

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.12.35

Remove upstreamed patches:
  bcm27xx/patches-6.12/950-0961-media-imx335-Use-correct-register-width-for-HNUM.patch [1]
  bcm27xx/patches-6.12/950-1003-drivers-media-i2c-imx335-Fix-frame-size-enumeration.patch [2]
  gemini/patches-6.12/0001-net-ethernet-cortina-Use-TOE-TSO-on-all-TCP.patch [3]
  generic/backport-6.12/300-v6.16-mips-Add-std-flag-specified.patch [4]
  mvebu/patches-6.12/0004-v6.16-pinctrl-armada-37xx-propagate-error-from-armada_37xx.patch [5]
  mvebu/patches-6.12/0005-v6.16-pinctrl-armada-37xx-propagate-error-from-armada_37xx.patch [6]
  mvebu/patches-6.12/0006-v6.16-pinctrl-armada-37xx-propagate-error-from-armada_37xx.patch [7]
  mvebu/patches-6.12/0007-v6.16-pinctrl-armada-37xx-propagate-error-from-armada_37xx.patch [8]

Manually rebased patches:
  bcm27xx/patches-6.12/950-0392-fbdev-Allow-client-to-request-a-particular-dev-fbN-n.patch [9]

All other patches are automatically refreshed.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.35&id=b93864e0865f235a791e69dc9ef4f896e559ef77
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.35&id=1f78790d988c9d55cf8d4b4d511d4b3e38ecb81d
[3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.35&id=2bd434bb0eeb680c2b3dd6c68ca319b30cb8d47f
[4] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.35&id=6dbda47fe8bd6aa978c150bc9d321a286d2cc3f4
[5] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.35&id=2cd2022c38fa26257cc6eec100ae122de9c1541c
[6] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.35&id=133f17922b3dbae44fe583fb898b92b03558a657
[7] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.35&id=aefe45843ea667366e35df4fcfef5ff9051a86c9
[8] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.35&id=461d5a73ae45fbe6c300a6e64600f9792684eb52
[9] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.35&id=3f2098f4fba7718eb2501207ca6e99d22427f25a

Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19249
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

realtek: Convert LGS310C to compressed kernel

There are too many supported Realtek devices so avoid activating the
rt loader recipe in the default builds. Just start with the LGS310C.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18397
Signed-off-by: Robert Marko <robimarko@gmail.com>

realtek: add rt-loader recipe

To make use of the new rt-loader provide the needed recipes.
This has been tested with the following devices:

- rtl838x Linksys LGS310: initramfs & flash
- rtl930x Zyxel XGS1210: initramfs

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18397
Signed-off-by: Robert Marko <robimarko@gmail.com>

realtek: add rt-loader (runtime loader)

The bootloader of many Realtek switches only supports gzipped kernel images.
With limited flash space that might get critical in future versions. For better
compression allow support for compressed images. For this a new loader was
developed. Several ideas have been taken over from the existing lzma loader
but this has been enhanced to make integration simpler. What is new:

- Loader is position independent. No need to define load addresses
- Loader identifies device memory on its own
- Loader uses "official" upstream kernel lzma uncompress
  https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/lib/decompress_unlzma.c
- Loader uses "official" UNMODIFIED nanoprintg that is used by several
  bare metal projects. https://github.com/charlesnicholson/nanoprintf

Compiled the loader ist just under 12KiB and during boot it will show:

rt-loader
Found RTL8380M (chip id 6275C) with 256MB
Relocate 2924240 bytes from 0x80100000 to 0x8fce0000
Extract kernel with 2900144 bytes from 0x8fce521c to 0x80100000...
Extracted kernel size is 9814907 bytes
Booting kernel from 0x80100000 ...

[    0.000000] Linux version 6.12.33 ...
[    0.000000] RTL838X model is 83806800
...

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18397
Signed-off-by: Robert Marko <robimarko@gmail.com>

wifi-scripts: ucode: fix invalid generated MAC address

macaddr_base can be NULL, in which case it needs to be passed as an empty string

Signed-off-by: Felix Fietkau <nbd@nbd.name>

uboot-tools: move ubootenv_add_ubi_default to common functions

The same function is used twice, so let's make it common.

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

uboot-tools: use ubootenv_add_* functions

Use ubootenv_add_* functions for code simplification.

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

uboot-tools: update ubootenv_add_* functions

Add posibility to specify:
- ROOTDEV (mmc)
- number of blocks (mtd)

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

uboot-tools: move ubootenv_add_* functions to common functions

Functions ubootenv_add_mtd, ubootenv_add_sys_mtd and ubootenv_add_mmc
can be shared so make them common.

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

wifi-scripts: iwinfo(ucode): add missing null checks

Signed-off-by: Felix Fietkau <nbd@nbd.name>