openwrt/staging/hauke.git
7 years agobzip2: add symlink to binary
Daniel Golle [Wed, 5 Jul 2017 14:25:23 +0000 (16:25 +0200)]
bzip2: add symlink to binary

Other distributions incl. the OpenWrt ImageBuilder and SDK
expect to find the bzip2 executable in /bin.
Create a symlink at that location for compatibility.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
7 years agobrcm63xx: remove misleading warning about partial SPI NOR writes
Jonas Gorski [Wed, 5 Jul 2017 08:53:00 +0000 (10:53 +0200)]
brcm63xx: remove misleading warning about partial SPI NOR writes

The warning will be triggered by jffs2 or UBI, and partial writes are no
issue for most flash chips.

Fixes: 2a2b16210bbc ("brcm63xx: backport upstream solution for SPI message size limits")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agoautomake: Update to version 1.15.1
Thomas Langer [Tue, 27 Jun 2017 16:26:28 +0000 (18:26 +0200)]
automake: Update to version 1.15.1

The new version includes the fix for new perl versions,
so remove the related patch.

Signed-off-by: Thomas Langer <thomas.langer.71@gmail.com>
7 years agokirkwood: drop kernel 4.4 support
Mathias Kresin [Wed, 28 Jun 2017 21:34:51 +0000 (23:34 +0200)]
kirkwood: drop kernel 4.4 support

Signed-off-by: Mathias Kresin <dev@kresin.me>
7 years agokirkwood: switch to kernel 4.9
Paul Wassi [Fri, 10 Mar 2017 18:10:29 +0000 (19:10 +0100)]
kirkwood: switch to kernel 4.9

Add patches-4.9, some of them (heavily) rewritten:
  - ea4500 is upstream available, keep only LEDE changes in dts
  - ea3500 is changed to match the structure of the upstream ea4500 dts
  - nsa310s rewritten to include the common dtsi
  - nsa325 is dropped, since already upstream

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[refresh kernel config, add on100, use the switchdev based mv88e6171
driver for the linksys boards, keep lede specific rootfs/kernel
partition names for linksys boards, reorder patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
7 years agolantiq: use img file extension for DGN3500 factory images
Mathias Kresin [Wed, 28 Jun 2017 21:36:37 +0000 (23:36 +0200)]
lantiq: use img file extension for DGN3500 factory images

The Netgear UI in basic mode refuses the upgrade file if the the
fileextension is not img. The expert/advanced mode accepts any
fileextension. Use img to make it work in any case.

Signed-off-by: Mathias Kresin <dev@kresin.me>
7 years agofirmware-utils: mktplinkfw: add option for endianness swap
Piotr Dymacz [Tue, 4 Jul 2017 13:40:43 +0000 (15:40 +0200)]
firmware-utils: mktplinkfw: add option for endianness swap

This adds command line option in "mktplinkfw" tool for endianness swap
in kernel load address and entry point fields. As in "mktplinkfw2" tool,
we will need this for little-endian targets, like "ramips".

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: fix TPLINK_BOARD_ID for Archer C58 and TL-WA855RE
Piotr Dymacz [Tue, 4 Jul 2017 13:09:52 +0000 (15:09 +0200)]
ar71xx: fix TPLINK_BOARD_ID for Archer C58 and TL-WA855RE

Rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID for two ommited devices.

Fixes: 7d6c63d ("build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID")
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agofirmware-utils: mktplinkfw2: add missing options descriptions
Piotr Dymacz [Tue, 4 Jul 2017 11:26:40 +0000 (13:26 +0200)]
firmware-utils: mktplinkfw2: add missing options descriptions

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: fix Netgear WNDR3700 v4 switch port mapping
Qian Zheng [Mon, 3 Jul 2017 07:15:11 +0000 (15:15 +0800)]
ar71xx: fix Netgear WNDR3700 v4 switch port mapping

Signed-off-by: Qian Zheng <sotux82@gmail.com>
7 years agoar71xx: add support for TP-Link TL-WR902AC v1
Piotr Dymacz [Sun, 2 Jul 2017 16:32:38 +0000 (18:32 +0200)]
ar71xx: add support for TP-Link TL-WR902AC v1

TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
  resitors are missing on TX/RX lines)
- 1x micro USB (for power only)

Flash instructions:

Use "factory" image under vendor GUI.

Recovery instructions:

This device contains tftp recovery mode inside U-Boot. You can use it to
flash LEDE (use "factory" image) or vendor firmware.

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin"
   to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
   and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.

Root access over serial line in vendor firmware: root/sohoadmin.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: generic: enable CONFIG_MTD_SPLIT_TPLINK_FW
Piotr Dymacz [Mon, 3 Jul 2017 16:57:36 +0000 (18:57 +0200)]
ar71xx: generic: enable CONFIG_MTD_SPLIT_TPLINK_FW

We can use "tplink-fw" mtd splitter for TP-Link devices which use kernel
with TP-Link header embedded inside "safeloader" image type and thus get
rid of statically defined "kernel" and "rootfs" partitions in cmdline.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: refresh and cleanup mikrotik subtarget kernel config
Piotr Dymacz [Mon, 3 Jul 2017 19:12:32 +0000 (21:12 +0200)]
ar71xx: refresh and cleanup mikrotik subtarget kernel config

Refresh mikrotik subtarget kernel config and enable kernel support for
boards which belong to this subtarget only.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: refresh and cleanup nand subtarget kernel config
Piotr Dymacz [Mon, 3 Jul 2017 17:51:13 +0000 (19:51 +0200)]
ar71xx: refresh and cleanup nand subtarget kernel config

Refresh nand subtarget kernel config and enable kernel support for
boards which belong to this subtarget only.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: refresh and cleanup target kernel config
Piotr Dymacz [Mon, 3 Jul 2017 17:49:04 +0000 (19:49 +0200)]
ar71xx: refresh and cleanup target kernel config

Refresh target kernel config and disable kernel support for all boards
which belong to nand and mikrotik subtargets only.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agodnsmasq: dnsmasq --rev-server support
DUPONCHEEL Sébastien [Wed, 28 Jun 2017 15:07:39 +0000 (17:07 +0200)]
dnsmasq: dnsmasq --rev-server support

This is functionally the same as --server, but provides some syntactic sugar to
make specifying address-to-name queries easier.

For example --rev-server=1.2.3.0/24,192.168.0.1 is exactly equivalent to
--server=/3.2.1.in-addr.arpa/192.168.0.1

Signed-off-by: DUPONCHEEL Sébastien <sebastien.duponcheel@corp.ovh.com>
7 years agofirmware-utils: mktplinkfw2: fix MD5 salt
Rafał Miłecki [Sun, 2 Jul 2017 15:06:58 +0000 (17:06 +0200)]
firmware-utils: mktplinkfw2: fix MD5 salt

LEDE supports few devices using TP-Link firmware format (V2 or V3):
ArcherC20i, ArcherC50, ArcherMR200, TDW8970, TDW8980, TL-WR840N v4,
TL-WR841N v13 and VR200v

Testing mktplinkfw2 tool with official (vendor generated) firmware files
for above devices has shown an error when comparing calculated and
included MD5 sum, e.g.:
> mktplinkfw2 -i Archer_C20iv1_0.9.1_3.2_up_boot\(170221\)_2017-02-21_17.14.03.bin | grep -A 1 MD5Sum1
Header MD5Sum1         : 22 5a cb 92 10 d2 95 7b df 62 9a f8 62 17 37 10 (*ERROR*)
          --> expected : ad 19 11 d1 78 98 a7 42 5f 2e 64 da 8a 34 ec cb

This problem has been verified to occur with:
Archer_C20iv1_0.9.1_3.2_up_boot(170221)_2017-02-21_17.14.03.bin
Archer MR200v1_0.9.1_1.1_up_boot_v004a.0 Build 160905 Rel.60037n.bin
TD-W8970v3_0.9.1_2.0_up_boot(160816)_2016-08-16_10.40.57.bin
TD-W8980v1_0.6.0_1.8_up_boot(150514)_2015-05-14_11.16.43.bin
Archer_VR200vv2_0.2.0_0.8.0_up_boot(161202)_2016-12-05_14.39.06.bin

For some images, e.g.:
Archer_C50v3_EU_0.9.1_0.3_up_boot[170417-rel52298].bin
TL-WR840Nv4_EU_0.9.1_4.16_up_boot[170421-rel70692].bin
TL-WR841Nv13_0.9.1_3.16_up_boot(161012).bin
mktplinkfw2 calculates zero MD5 so these has to be fixed separately:
> mktplinkfw2 -i TL-WR841Nv13_0.9.1_3.16_up_boot\(161012\).bin | grep -A 1 MD5Sum1
Header MD5Sum1         : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 (*ERROR*)
          --> expected : 6f 1d 9b 57 5d 42 14 6d bf a2 03 9d 46 7d 55 55

It's most likely that MD5 salt used in mktplinkfw2 has been always wrong
(and it's not a matter of e.g. a vendor change). Update it to fix MD5
calculation.

This has been also verified to calculate MD5 correctly for other (not
yet supported) devices, e.g.:
Archer_C3150v2_0.1.0_0.9.1_up_boot(160812)_2016-08-12_10.52.54.bin
Archer_C3200v1_0.9.1_0.1_up_boot(160704)_2016-07-04_15.48.28.bin

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Mathias Kresin <dev@kresin.me>
7 years agobrcm47xx: Add support for kernel 4.9
Hauke Mehrtens [Sun, 2 Jul 2017 12:12:45 +0000 (14:12 +0200)]
brcm47xx: Add support for kernel 4.9

I tested this on a WRT54GS and a WRT610N V1.
The WRT610N does not boot when the kernel is too big, so I deactivated KALLSYMS

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
7 years agobrcm47xx: refresh kernel configuration
Hauke Mehrtens [Sun, 2 Jul 2017 12:12:22 +0000 (14:12 +0200)]
brcm47xx: refresh kernel configuration

Run make kernel_oldconfig on the brcm47xx target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
7 years agobrcm47xx: remove kernel 4.1 support
Hauke Mehrtens [Sun, 2 Jul 2017 11:29:43 +0000 (13:29 +0200)]
brcm47xx: remove kernel 4.1 support

Kernel 4.1 is not supported by LEDE for some time now.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
7 years agobrcm47xx: use DMZ LED as status indicator
Mirko Parthey [Mon, 26 Jun 2017 16:25:45 +0000 (18:25 +0200)]
brcm47xx: use DMZ LED as status indicator

On the Linksys WRT54GSv1, the Power LED flickers in the "off" state.
Indicate status using the DMZ LED if available, since it has solid "on" and
"off" states.

This change was tested on the WRT54GSv1, but may also affect other brcm47xx
devices.

Fixes FS#793.

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
7 years agobrcm47xx: resolve GPIO conflict for WRT54GSv1
Mirko Parthey [Mon, 26 Jun 2017 16:25:46 +0000 (18:25 +0200)]
brcm47xx: resolve GPIO conflict for WRT54GSv1

On the Linksys WRT54GSv1, the adm6996 switch driver and the
gpio_button_hotplug module both claim GPIO 6, which is connected to the
Reset button.  When the switch driver's request wins, the Reset button
cannot work. This makes it impossible to enter failsafe mode without a
serial console.

Stop requesting the "adm_rc" GPIO in the switch driver, since it is not
used anywhere.

Fixes FS#792.

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
7 years agofirmware-utils: mktplinkfw2: fix support for -w option
Rafał Miłecki [Sun, 2 Jul 2017 20:28:24 +0000 (22:28 +0200)]
firmware-utils: mktplinkfw2: fix support for -w option

This fixes copy & paste typo when reading -w argument.

Fixes: 4b35e174caa5b ("firmware-utils: mktplinkfw2: support additional hardware version")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
7 years agokernel: add missing symbol to generic
Jonas Gorski [Thu, 29 Jun 2017 09:01:59 +0000 (11:01 +0200)]
kernel: add missing symbol to generic

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: refresh smp config
Jonas Gorski [Thu, 29 Jun 2017 12:49:35 +0000 (14:49 +0200)]
brcm63xx: refresh smp config

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: enable KEXEC for SMP again
Jonas Gorski [Thu, 29 Jun 2017 12:15:15 +0000 (14:15 +0200)]
brcm63xx: enable KEXEC for SMP again

It seems it compiles again, so there is no reason to keep it disabled.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: disable commandline parts parser
Jonas Gorski [Thu, 29 Jun 2017 11:43:45 +0000 (13:43 +0200)]
brcm63xx: disable commandline parts parser

We don't use it, so no need to have it enabled.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: add support for the Actiontec R1000H gateway
Anthony Sepa [Sun, 19 Feb 2017 18:27:36 +0000 (14:27 -0400)]
brcm63xx: add support for the Actiontec R1000H gateway

SOC: Broadcom BCM6368 (2 * Broadcom BMIPS4350 V3.1 / 400 MHz)
Flash size: 32MB (split 16/16 dual boot)
RAM size: 64MB
Wireless: BCM432x 802.11a/b/g/n(pci)
Ethernet: Broadcom BCM53115
USB: 1 x USB 2.0

Known issues:
 - Unable to detect 53115 switch attached to MDIO. Not supported
 - No support for the cable port

More info on the device and the research can be found at:
http://www.actiontec.com/212.html

Same FCC ID as:
https://wikidevi.com/wiki/Actiontec_V1000H_(Telus)

Signed-off-by: Anthony Sepa <anthonysepa@yahoo.ca>
[jonas.gorski: fix commit subject/message]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agobrcm63xx: fix bcm6328 pinmux other register
Jonas Gorski [Wed, 28 Jun 2017 10:06:43 +0000 (12:06 +0200)]
brcm63xx: fix bcm6328 pinmux other register

The pinmux register is at relative offset 0x8, not 0xc. Fixes hang
when trying to modify pins >= 32.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
7 years agoar71xx: fix typo in network defaults
Jo-Philipp Wich [Thu, 29 Jun 2017 16:01:11 +0000 (18:01 +0200)]
ar71xx: fix typo in network defaults

Commit 9fec39a (ar71xx: add support for TP-Link TL-WA855RE v1) introduced a
typo in 02_network, fix it by removing the stray paren.

Reported-by: Henryk Heisig <hyniu@o2.pl>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7 years agoar71xx: image: specify TPLINK_HWID for TP-Link RE450
Piotr Dymacz [Tue, 27 Jun 2017 20:49:21 +0000 (22:49 +0200)]
ar71xx: image: specify TPLINK_HWID for TP-Link RE450

TPLINK_HWID hasn't been specified for TP-Link RE450 since the begin.
As we don't want to break sysupgrade (all existing LEDE release images
for this board have TPLINK_HWID set to 0x0), set it explicitly to 0x0.

Fixes FS#852

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13
Piotr Dymacz [Wed, 21 Jun 2017 12:16:15 +0000 (14:16 +0200)]
ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13

TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.

The difference between these two models is in number of available
LEDs, buttons and power input switch.

This work is partially based on GitHub PR#974.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
  switch

* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.

Factory image notes:

These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.

We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.

Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.

The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".

Flash instruction:

Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

To access U-Boot CLI, keep pressed "4" key during boot.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoramips: image: simplify TP-Link Archer devices definitions
Piotr Dymacz [Fri, 23 Jun 2017 21:20:53 +0000 (23:20 +0200)]
ramips: image: simplify TP-Link Archer devices definitions

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agobuild: move mktplinkfw2 related commands to image-commands.mk
Piotr Dymacz [Fri, 23 Jun 2017 21:07:10 +0000 (23:07 +0200)]
build: move mktplinkfw2 related commands to image-commands.mk

There are already two targets (lantiq, ramips) which use mktplinkfw2
tool for creating images. This de-duplicates code, introduces two new
build commands: tplink-v2-header, tplink-v2-image and makes use of
them in place of old, (sub)target specific ones.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agobuild: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID
Piotr Dymacz [Tue, 27 Jun 2017 12:48:00 +0000 (14:48 +0200)]
build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agofirmware-utils: mktplinkfw2: support additional hardware version
Piotr Dymacz [Wed, 21 Jun 2017 12:15:55 +0000 (14:15 +0200)]
firmware-utils: mktplinkfw2: support additional hardware version

As it turned out, some of new MediaTek based TP-Link devices use value
from field at 0x3c offset in version 3 of TP-Link header to specify
"Additional Hardware Version".

Value from this field is validated during regular (GUI) firmware upgrade
on devices like TL-WR840N v4 or TL-WR841N v13. If it's zero (based on
some tests, it seems that firmware will accept anything != 0), errors
like below are printed on console and upgrade fails:

[ rsl_sys_updateFirmware ] 2137:  Firmware Additional HardwareVersion
check failed

[ rdp_updateFirmware ] 345:  perror:4506

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: fix switch port mapping for TP-Link TL-WR74xN/D series
Piotr Dymacz [Tue, 27 Jun 2017 11:13:36 +0000 (13:13 +0200)]
ar71xx: fix switch port mapping for TP-Link TL-WR74xN/D series

Fixes FS#843

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agoar71xx: add support for TP-Link Archer C58 v1
Henryk Heisig [Fri, 16 Jun 2017 13:26:30 +0000 (15:26 +0200)]
ar71xx: add support for TP-Link Archer C58 v1

TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm
QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 3x button
- UART header on PCB, RX, TX at TP4+5 (backside)

QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to
patch macaddress.

Flash instruction:

Use "factory" image directly in vendor GUI.

Recovery method:

1. Set PC to fixed ip address 192.168.0.66/24.
2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and
   rename it to "tp_recovery.bin".
3. Start a tftp server with the file "tp_recovery.bin" in its root
   directory.
4. Turn off the router.
5. Press and hold Reset button.
6. Turn on router with the reset button pressed and wait ~15 seconds.
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server.
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b $fileaddr 0x9f020000 $filesize
reset

This commit is based on GitHub PR#1112

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
7 years agofirmware-utils: tplink-safeloader: add support for Archer C5 v2 JP/US
Jean-Pierre St-Yves [Tue, 27 Jun 2017 08:20:19 +0000 (10:20 +0200)]
firmware-utils: tplink-safeloader: add support for Archer C5 v2 JP/US

Add support for Japan and US versions of TP-Link Archer C5 v2

Signed-off-by: Jean-Pierre St-Yves <jpstyves@gmail.com>
7 years agofirmware-utils: tplink-safeloader: add support for Archer C59/C60 RU
Henryk Heisig [Wed, 14 Jun 2017 14:38:30 +0000 (16:38 +0200)]
firmware-utils: tplink-safeloader: add support for Archer C59/C60 RU

Add support for Russian version of TP-Link Archer C59/C60 v1

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
7 years agoar71xx: add support for TP-Link TL-WA855RE v1
Federico Cappon [Fri, 9 Jun 2017 15:11:39 +0000 (15:11 +0000)]
ar71xx: add support for TP-Link TL-WA855RE v1

TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/397/198 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 2x LED (green and orange in the same package), 2x button
- UART: TP5(TX) and TP4(RX) test points on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.

Signed-off-by: Federico Cappon <dududede371@gmail.com>
7 years agoar71xx: fix EnGenius ENS202EXT mtd definition
Piotr Dymacz [Wed, 14 Jun 2017 13:23:35 +0000 (15:23 +0200)]
ar71xx: fix EnGenius ENS202EXT mtd definition

Use statically defined sizes for kernel and rootfs mtd partitions.
Vendor upgrade script writes both firmware parts independently which
ends up in a gap between kernel and rootfs images. This results in
incorrectly calculated rootfs_data start offset.

Also, fix IMAGE_SIZE, DEVICE_PACKAGES and drop redundant KERNEL
definition.

Fixes FS#835

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
7 years agouboot-envtools: add Arduino Yun support
Camille Bilodeau [Tue, 13 Jun 2017 08:33:34 +0000 (10:33 +0200)]
uboot-envtools: add Arduino Yun support

Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
7 years agoar71xx: move Arduino Yun to generic building code
Camille Bilodeau [Tue, 13 Jun 2017 08:05:13 +0000 (10:05 +0200)]
ar71xx: move Arduino Yun to generic building code

Migrate Arduino Yun from legacy to generic building code.

Note: the mtd partitioning is changed to adopt the LEDE default
partitioning. It allows to have a kernel bigger than 1280k. It is
necessary as kernel > 4.4 with default LEDE configuration grows
bigger.

To use the new partitioning, you need to update your U-Boot env in
advance:

setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro"
setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000"
saveenv

Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
7 years agoar71xx: remove Arduino Yun 8 MiB prototype
Camille Bilodeau [Mon, 12 Jun 2017 12:11:23 +0000 (14:11 +0200)]
ar71xx: remove Arduino Yun 8 MiB prototype

The Arduino Yun has 16 MiB flash. Early prototype boards with 8 MiB were
not available for sell:

https://blog.arduino.cc/2013/08/21/updating-about-arduino-yun-and-arduino-robot/

Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
7 years agoar71xx: wpj344: set MAC on wan
Leon M. George [Fri, 9 Jun 2017 16:30:47 +0000 (18:30 +0200)]
ar71xx: wpj344: set MAC on wan

Signed-off-by: Leon M. George <leon@georgemail.eu>
7 years agoar71xx: wpj344: remove unused eth1 device
Leon M. George [Fri, 9 Jun 2017 11:57:56 +0000 (13:57 +0200)]
ar71xx: wpj344: remove unused eth1 device

Signed-off-by: Leon M. George <leon@georgemail.eu>
7 years agoar71xx: wpj344: read MAC addresses from u-boot mtd
Leon M. George [Thu, 8 Jun 2017 14:01:19 +0000 (16:01 +0200)]
ar71xx: wpj344: read MAC addresses from u-boot mtd

This way, the assigned addresses match those on the barcode labels.
Otherwise, the addresses appear to vary on boot.

Signed-off-by: Leon M. George <leon@georgemail.eu>
7 years agodhcpv6: add missing dollar sign in dhcpv6 script (FS#874)
Hans Dedecker [Thu, 29 Jun 2017 07:41:59 +0000 (09:41 +0200)]
dhcpv6: add missing dollar sign in dhcpv6 script (FS#874)

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
7 years agokernel: cleanup CONFIG_SCHED_HRTICK
Stijn Tintel [Thu, 29 Jun 2017 02:46:59 +0000 (04:46 +0200)]
kernel: cleanup CONFIG_SCHED_HRTICK

Remove CONFIG_SCHED_HRTICK from target configs, as it was added to the
generic config in b47fd7656336162360ebf66147326763ddae3f8d.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
7 years agoarmvirt: rename config-default to config-4.9
Stijn Tintel [Thu, 29 Jun 2017 01:36:19 +0000 (03:36 +0200)]
armvirt: rename config-default to config-4.9

The kernel configs for all targets should have the version in the
filename, for clearness and consistency across all targets.
It is also expected by the update_kernel.sh script.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
7 years agodnsmasq: backport patch fixing DNS failover (FS#841)
Hans Dedecker [Wed, 28 Jun 2017 08:15:38 +0000 (10:15 +0200)]
dnsmasq: backport patch fixing DNS failover (FS#841)

Backport upstream dnsmasq patch fixing DNS failover when first servers
returns REFUSED in strict mode; fixes issue FS#841.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
7 years agokernel: backport usbport LED trigger driver support for DT
Rafał Miłecki [Wed, 28 Jun 2017 09:31:14 +0000 (11:31 +0200)]
kernel: backport usbport LED trigger driver support for DT

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
7 years agodropbear: add option to set max auth tries
Stijn Tintel [Tue, 27 Jun 2017 20:30:01 +0000 (22:30 +0200)]
dropbear: add option to set max auth tries

Add a uci option to set the new max auth tries paramater in dropbear.
Set the default to 3, as 10 seems excessive.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
7 years agodropbear: server support option '-T' max auth tries
Kevin Darbyshire-Bryant [Sun, 25 Jun 2017 20:40:43 +0000 (21:40 +0100)]
dropbear: server support option '-T' max auth tries

Add support for '-T n' for a run-time specification for maximum number
of authentication attempts where 'n' is between 1 and compile time
option MAX_AUTH_TRIES.

A default number of tries can be specified at compile time using
'DEFAULT_AUTH_TRIES' which itself defaults to MAX_AUTH_TRIES for
backwards compatibility.

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
7 years agohostapd: configure NAS ID regardless of encryption
Yury Shvedov [Tue, 27 Jun 2017 08:43:54 +0000 (11:43 +0300)]
hostapd: configure NAS ID regardless of encryption

RADIUS protocol could be used not only for authentication but for
accounting too. Accounting could be configured for any type of networks.
However there is no way to configure NAS Identifier for non-WPA
networks without this patch.

Signed-off-by: Yury Shvedov <yshvedov@wimarksystems.com>
[cleanup commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
7 years agohostapd: add acct_interval option
Yury Shvedov [Tue, 27 Jun 2017 07:34:49 +0000 (10:34 +0300)]
hostapd: add acct_interval option

Make an ability to configure Accounting-Interim-Interval via UCI

Signed-off-by: Yury Shvedov <yshvedov@wimarksystems.com>
[add hostapd prefix, cleanup commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
7 years agomxs: drop 4.4 support
Michael Heimpold [Wed, 7 Jun 2017 18:29:29 +0000 (20:29 +0200)]
mxs: drop 4.4 support

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
7 years agomxs: add support for 4.9 and switch over
Michael Heimpold [Thu, 11 May 2017 21:07:06 +0000 (23:07 +0200)]
mxs: add support for 4.9 and switch over

I did not port the regulator and power patches from Stefan Wahren
because I talked to him and he told me that work on this is currently
stalled. And since AFAIK nothing depends on these patches, leaving them
out seems reasonable.

I build minimum default configurations and run-tested them on both
I2SE Duckbill devices and Olimex Olinuxino Maxi boards successfully [1].

[1] Tested:
- debug uart is working
- boot without any obvious kernel problem
- network is coming up and data transfer is possible
- Olinuxino: USB detects a plugged-in pen drive

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
[refreshed config and patches]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
7 years agokernel: disable various symbols for v4.9
Michael Heimpold [Thu, 11 May 2017 21:01:30 +0000 (23:01 +0200)]
kernel: disable various symbols for v4.9

In preparation for bumping mxs target to 4.9, disable a bunch of configuration
symbols that provoked config prompts.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
7 years agoath10k-firmware: add qca9888 firmware
John Crispin [Mon, 8 May 2017 06:51:46 +0000 (08:51 +0200)]
ath10k-firmware: add qca9888 firmware

ath10k-firmware: add qca9888 firmware

the firmware files for qca9888 were previously not packaged. add the meta
information for doing so.

Signed-off-by: John Crispin <john@phrozen.org>
7 years agokernel: update kernel 4.4 to 4.4.74
Stijn Tintel [Tue, 27 Jun 2017 05:41:10 +0000 (07:41 +0200)]
kernel: update kernel 4.4 to 4.4.74

Refresh patches.
Compile-tested on ar71xx.
Runtime-tested on ar71xx.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
7 years agokernel: update kernel 4.9 to 4.9.34
Koen Vandeputte [Mon, 26 Jun 2017 09:22:11 +0000 (11:22 +0200)]
kernel: update kernel 4.9 to 4.9.34

- Refreshed all patches
- Adapted 1 (0031-mtd-add-SMEM-parser-for-QCOM-platforms.patch)

Compile tested on: brcm2708, cns3xxx, imx6
Run tested on: brcm2708, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Compile and run tested on brcm2708]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
7 years agokernel: use .patch extension for all patches
Stijn Tintel [Tue, 27 Jun 2017 04:37:46 +0000 (06:37 +0200)]
kernel: use .patch extension for all patches

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
7 years agofirmware-utils: fix dgn3500sum compiler warnings
Mathias Kresin [Mon, 26 Jun 2017 17:22:52 +0000 (19:22 +0200)]
firmware-utils: fix dgn3500sum compiler warnings

The sum variable need to be initialised, otherwise it will points to
random stack memory and a bogus image checksum might be calculated.

While at it, fix the segfault in case the product region code isn't
specified and enable compiler warnings which had revealed all the code
issues.

Signed-off-by: Mathias Kresin <dev@kresin.me>
7 years agodnsmasq: backport tweak ICMP ping logic for DHCPv4
Hans Dedecker [Mon, 26 Jun 2017 08:23:08 +0000 (10:23 +0200)]
dnsmasq: backport tweak ICMP ping logic for DHCPv4

Don't start ping-check of address in DHCP discover if there already
exists a lease for the address. It has been reported under some
circumstances android and netbooted windows devices can reply to
ICMP pings if they have a lease and thus block the allocation of
the IP address the device already has during boot.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
7 years agoprocd: support term_timeout parameter
Jo-Philipp Wich [Tue, 20 Jun 2017 11:44:10 +0000 (13:44 +0200)]
procd: support term_timeout parameter

Expose "term_timeout" parameter in procd.sh to allow init scripts to
request a longer termination timeout.

This is required to fix FS#859 in a later commit.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7 years agoprocd: assign /dev/tty* nodes to "tty" group
Jo-Philipp Wich [Sat, 10 Jun 2017 18:51:33 +0000 (20:51 +0200)]
procd: assign /dev/tty* nodes to "tty" group

Adjust default permissions and ownership of /dev/tty* nodes from
0600/root:root to 0660/root:tty in order to support granting
unprivileged user access when needed.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7 years agobase-files: add "tty" user group
Jo-Philipp Wich [Sat, 10 Jun 2017 18:49:10 +0000 (20:49 +0200)]
base-files: add "tty" user group

This is needed for an upcoming change to the hotplug default rules which
will cause /dev/tty* nodes to get assigned to the "tty" group in order
to support unprivileged user access when needed.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7 years agoopenvpn: update to 2.4.3
Magnus Kroken [Thu, 22 Jun 2017 21:01:01 +0000 (23:01 +0200)]
openvpn: update to 2.4.3

Fixes for security and other issues. See security announcement for more details:
https://community.openvpn.net/openvpn/wiki/VulnerabilitiesFixedInOpenVPN243

* Remotely-triggerable ASSERT() on malformed IPv6 packet (CVE-2017-7508)
* Pre-authentication remote crash/information disclosure for clients (CVE-2017-7520)
* Potential double-free in --x509-alt-username (CVE-2017-7521)
* Remote-triggerable memory leaks (CVE-2017-7512)
* Post-authentication remote DoS when using the --x509-track option (CVE-2017-7522)
* Null-pointer dereference in establish_http_proxy_passthru()
* Restrict --x509-alt-username extension types
* Fix potential 1-byte overread in TCP option parsing
* Fix mbedtls fingerprint calculation
* openssl: fix overflow check for long --tls-cipher option
* Ensure option array p[] is always NULL-terminated
* Pass correct buffer size to GetModuleFileNameW() (Quarkslabs finding 5.6)

Signed-off-by: Magnus Kroken <mkroken@gmail.com>
7 years agombedtls: update to 2.5.1
Magnus Kroken [Wed, 21 Jun 2017 19:05:09 +0000 (21:05 +0200)]
mbedtls: update to 2.5.1

Fixes some security issues (no remote exploits), and introduces
some changes. See release notes for details:
https://tls.mbed.org/tech-updates/releases/mbedtls-2.5.1-2.1.8-and-1.3.20-released

* Fixes an unlimited overread of heap-based buffers in mbedtls_ssl_read()
* Adds exponent blinding to RSA private operations
* Wipes stack buffers in RSA private key operations (rsa_rsaes_pkcs1_v15_decrypt(), rsa_rsaes_oaep_decrypt())
* Removes SHA-1 and RIPEMD-160 from the default hash algorithms for certificate verification.
* Fixes offset in FALLBACK_SCSV parsing that caused TLS server to fail to detect it sometimes.
* Tighten parsing of RSA PKCS#1 v1.5 signatures, to avoid a potential Bleichenbacher/BERserk-style attack.

Signed-off-by: Magnus Kroken <mkroken@gmail.com>
7 years agoar71xx/images/senao: fix reproducible issue using tar
Alexander Couzens [Sat, 24 Jun 2017 16:33:52 +0000 (18:33 +0200)]
ar71xx/images/senao: fix reproducible issue using tar

Use deterministic sorting
Use numeric owner/group
Set uid/gid to 0

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
7 years agoar71xx/image: make tar calls reproducible
Alexander Couzens [Sun, 18 Jun 2017 19:30:30 +0000 (21:30 +0200)]
ar71xx/image: make tar calls reproducible

Use --mtime when SOURCE_DATE_EPOCH is set.
Use gzip -n9z instead of tar z to remove
timestamp in gzip header.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
7 years agoapm821xx: MR24: fix ethernet phy detection on the MR24
Christian Lamparter [Wed, 7 Jun 2017 23:32:26 +0000 (23:32 +0000)]
apm821xx: MR24: fix ethernet phy detection on the MR24

To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
This patch fixes a problem where the AR8035 PHY can't be
detected on the Cisco Meraki MR24, when the ethernet cable
is not connected during boot.

Russell Senior reported:
|This appears to be a problem during probing of the AR8035
|phy chip. When ethernet has no link, the phy detection fails,
|and eth0 is not created. Plugging ethernet later has no effect,
|because there is no interface as far as the kernel is
|concerned. The relevant part of the boot log looks like this:
|
|[    0.876611] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
|[    0.882532] /plb/opb/ethernet@ef600c00: reset timeout
|[    0.888546] /plb/opb/ethernet@ef600c00: can't find PHY!
(<https://bugs.lede-project.org/index.php?do=details&task_id=687>)

Fixes FS#687
Cc: Chris Blake <chrisrblake93@gmail.com>
Reported-by: Russell Senior <russell@personaltelco.net>
Fixes: 23fbb5a87c56e98 ("emac: Fix EMAC soft reset on 460EX/GT")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
7 years agotreewide: add license tags
Florian Eckert [Wed, 7 Jun 2017 09:01:06 +0000 (11:01 +0200)]
treewide: add license tags

Add licence tags where missing.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
7 years agoramips: add MT7603E driver to AFoundry EW1200
Mathias Kresin [Fri, 23 Jun 2017 05:57:32 +0000 (07:57 +0200)]
ramips: add MT7603E driver to AFoundry EW1200

Add the MT7603E driver for the 2.4GHz wireless.

Signed-off-by: Mathias Kresin <dev@kresin.me>
7 years agoar71xx: add AVM FRITZ!WLAN Repeater 300E support
Mathias Kresin [Fri, 30 Dec 2016 10:53:21 +0000 (11:53 +0100)]
ar71xx: add AVM FRITZ!WLAN Repeater 300E support

Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)

To install LEDE via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1

Signed-off-by: Mathias Kresin <dev@kresin.me>
7 years agoar71xx: add AR724x PCIe init fixes
Mathias Kresin [Thu, 30 Mar 2017 20:01:09 +0000 (22:01 +0200)]
ar71xx: add AR724x PCIe init fixes

Add upstream send AR724x PCIe patches to get the PCIe controller out of
reset during driver init.

The AVM Fritz 300E bootloader doesn't take care of releasing the
different PCIe controller related resets which causes an endless hang
as soon as either the PCIE Reset register (0x180f0018) or the PCI
Application Control register (0x180f0000) is read from.

Signed-off-by: Mathias Kresin <dev@kresin.me>
7 years agobuild: move lzma2eva build step to image-commands.mk
Mathias Kresin [Sat, 25 Mar 2017 18:18:37 +0000 (19:18 +0100)]
build: move lzma2eva build step to image-commands.mk

Move it to image-commands.mk so that it can used by other targets with
eva based boards as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
7 years agokernel: move Lantiq PEF7061/7071/7072 phy driver to generic
Mathias Kresin [Fri, 30 Dec 2016 07:35:21 +0000 (08:35 +0100)]
kernel: move Lantiq PEF7061/7071/7072 phy driver to generic

The driver is used for boards outside the lantiq target as well. Move
it to generic to make it available for more targets.

The phy driver is included in kernel 4.8 as INTEL_XWAY_PHY.

Signed-off-by: Mathias Kresin <dev@kresin.me>
7 years agofritz_tffs_read: get tffs size from input file
Mathias Kresin [Sun, 18 Jun 2017 08:28:18 +0000 (10:28 +0200)]
fritz_tffs_read: get tffs size from input file

Use the size of the input file as maximum tffs size instead of a fixed
value. The tffs on a AVM Fritz 300E can be up to 512KByte for example.

Fixes a read error for the AVM Fritz 3370 where the tffs partition size
is 64Kbyte and smaller than the former default value of 256KByte.

Signed-off-by: Mathias Kresin <dev@kresin.me>
7 years agolibreadline: add host-build
Daniel Golle [Sat, 24 Jun 2017 11:58:56 +0000 (13:58 +0200)]
libreadline: add host-build

Also make sure that the PKG_NAME and folder name are equal.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
7 years agovalgrind: bump to 3.13.0
Luiz Angelo Daros de Luca [Sat, 17 Jun 2017 03:54:45 +0000 (00:54 -0300)]
valgrind: bump to 3.13.0

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
7 years agoca-certificates: Update to version 20161130+nmu1
Christian Schoenebeck [Mon, 19 Jun 2017 18:56:17 +0000 (20:56 +0200)]
ca-certificates: Update to version 20161130+nmu1

Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
7 years agobusybox: ash/hush fix for read-builtin command
Bastian Bittorf [Wed, 31 May 2017 10:50:08 +0000 (12:50 +0200)]
busybox: ash/hush fix for read-builtin command

this is a cherrypick from busybox-git HEAD:
f5470419404d643070db99d058405b714695b817

and can be removed when upgrading to
next busybox release. discussion here:
http://lists.busybox.net/pipermail/busybox/2017-May/085439.html

Signed-off-by: Bastian Bittorf <bb@npl.de>
7 years agogcc: gcc 6.3.0 fix comparison between pointer and integer
Kevin Darbyshire-Bryant [Fri, 9 Jun 2017 12:29:48 +0000 (13:29 +0100)]
gcc: gcc 6.3.0 fix comparison between pointer and integer

Fix FS#832

/source/build_dir/toolchain-mips_74kc_gcc-6.3.0_musl/gcc-6.3.0/gcc/ubsan.c:
In function 'bool ubsan_use_new_style_p(location_t)':
/source/build_dir/toolchain-mips_74kc_gcc-6.3.0_musl/gcc-6.3.0/gcc/ubsan.c:1474:23:
error: ISO C++ forbids comparison between pointer and integer
[-fpermissive]
       || xloc.file == '\0' || xloc.file[0] == '\xff'
                       ^~~~
make[5]: *** [Makefile:1085: ubsan.o] Error 1

https://www.viva64.com/en/b/0425/#ID0EMGCI

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
7 years agohostapd: add support for acs_chan_bias option
Kevin Darbyshire-Bryant [Thu, 15 Jun 2017 11:48:56 +0000 (12:48 +0100)]
hostapd: add support for acs_chan_bias option

During auto channel selection we may wish to prefer certain channels
over others.

e.g. we can just squeeze 4 channels into europe so '1:0.8 5:0.8 9:0.8
13:0.8' does that.

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
7 years agobusybox: backport 'ip rule suppress_{prefixlength, ifgroup}'
Stefan Tomanek [Mon, 19 Jun 2017 10:41:11 +0000 (12:41 +0200)]
busybox: backport 'ip rule suppress_{prefixlength, ifgroup}'

This is a backport from the busybox repository
(192dce4b84fb32346ebc5194de7daa5da3b8d1b4); it enables the use of the
suppress_{prefixlength,ifgroup} flags for policy routing rules.

Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
7 years agoprocd: update to latest version
Hans Dedecker [Fri, 23 Jun 2017 20:30:06 +0000 (22:30 +0200)]
procd: update to latest version

e5e99c4 watchdog: add support for starting/stopping kernel watchdog

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
7 years agokernel: backport MTD patch extracing TRX code to separated parser
Rafał Miłecki [Fri, 23 Jun 2017 08:58:16 +0000 (10:58 +0200)]
kernel: backport MTD patch extracing TRX code to separated parser

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
7 years agokernel: backport upstream mtd support for partition parsers
Rafał Miłecki [Fri, 23 Jun 2017 08:47:18 +0000 (10:47 +0200)]
kernel: backport upstream mtd support for partition parsers

In a log term it should replace our implementation. For now both can
coexist.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
7 years agokernel: backport upstream mtdpart.c cleanups
Rafał Miłecki [Fri, 23 Jun 2017 08:27:20 +0000 (10:27 +0200)]
kernel: backport upstream mtdpart.c cleanups

Except for renames and line changes the only conflict was in
allocate_partition in handling MTD_WRITEABLE. Hopefully it was handled
correctly.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
7 years agokernel: don't switch allocate_partition to use mtd_roundup_to_eb
Rafał Miłecki [Fri, 23 Jun 2017 06:59:46 +0000 (08:59 +0200)]
kernel: don't switch allocate_partition to use mtd_roundup_to_eb

This mtd_roundup_to_eb helper was introduced years ago in the commit
daec7ad768841 ("kernel/3.10: add separate rootfs partition parser") and
it was probably supposed to simplify code a bit.

With the recent upstream commit 1eeef2d7483a7 ("mtd: handle partitioning
on devices with 0 erasesize") the logic in allocate_partition got
slightly more complex and we can't use this simple helper anymore as it
doesn't support MTD_NO_ERASE properly.

There also isn't any real gain from this helper, so it's probably easier
to just don't use it *or* work on upstreaming it to avoid maintenance
cost.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
7 years agobase-files: fix PKG_CONFIG_DEPENDS to include version.mk entries
Rafał Miłecki [Fri, 16 Jun 2017 11:23:22 +0000 (13:23 +0200)]
base-files: fix PKG_CONFIG_DEPENDS to include version.mk entries

Including version.mk sets PKG_CONFIG_DEPENDS to config entries used for
VERSION_SED command. We should keep these configs to make sure package
gets refreshed when needed.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
7 years agodnsmasq: add dhcp-range tags configuration
Grégoire Delattre [Tue, 20 Jun 2017 09:45:49 +0000 (11:45 +0200)]
dnsmasq: add dhcp-range tags configuration

dnsmasq can match tags in its dhcp-range configuration, this commit adds
the option to configure it in the dhcp section

uci configuration:
config dhcp 'lan'
        option interface 'lan'
        list tag 'blue'
        list tag '!red'
        option start '10'
        option limit '150'
        option leasetime '12h'

generated dnsmasq configuration:
dhcp-range=tag:blue,tag:!red,set:lan,192.168.1.10,192.168.1.159,255.255.255.0,12h

Signed-off-by: Grégoire Delattre <gregoire.delattre@gmail.com>
7 years agoprocd: update to latest git HEAD
Daniel Golle [Mon, 19 Jun 2017 14:14:42 +0000 (16:14 +0200)]
procd: update to latest git HEAD

453116e system: introduce new attribute board_name
e5b963a preinit: define _GNU_SOURCE
e5ff8ca upgraded: cmake: Find and include uloop.h
f367ec6 hotplug: fix a memory leak in handle_button_complete()
796ba3b service/service_stopped(): fix a use-after-free
79bbe6d system: return legacy board name

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
7 years agobuild: Fix not altering KERNELRELEASE for external kernel
Hauke Mehrtens [Sun, 18 Jun 2017 21:27:51 +0000 (23:27 +0200)]
build: Fix not altering KERNELRELEASE for external kernel

When an external kernel tree is used the version should not get
modified by the LEDE build scripts. This was added by Florian some time
ago.
The commit 0aed054becb21439 ("build: add KERNEL_MAKE and
KERNEL_MAKE_FLAGS variables and move to kernel.mk") breaks this feature
introduced in b6746a6ffb73 ("include: Do not alter KERNELRELEASE for
external/git kernels").

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
7 years agomtd-utils/mkfs.jffs2: honor env SOURCE_DATE_EPOCH
Alexander Couzens [Sun, 18 Jun 2017 19:28:59 +0000 (21:28 +0200)]
mtd-utils/mkfs.jffs2: honor env SOURCE_DATE_EPOCH

Use the timestamp from the enviroment SOURCE_DATE_EPOCH
if set instead of the build time.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
7 years agofirmware-utils: honor env SOURCE_DATE_EPOCH
Alexander Couzens [Sun, 18 Jun 2017 00:21:21 +0000 (02:21 +0200)]
firmware-utils: honor env SOURCE_DATE_EPOCH

Use the timestamp from the enviroment SOURCE_DATE_EPOCH
if set instead of the build time.
Fixes reproducible builds for certain firmware images.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
7 years agolibunwind: update to version 1.2.1
Yousong Zhou [Mon, 19 Jun 2017 06:41:47 +0000 (14:41 +0800)]
libunwind: update to version 1.2.1

Changes since 1.2

    a77b0cd Bump version to v1.2.1
    5f354cb mips/tilegx: Add missing unwind_i.h header file
    620d1c3 Add aarch64 getcontext functionality.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>