From 16d7058facb0a7989eb47fc09ff4afca3f08ab7b Mon Sep 17 00:00:00 2001 From: Matteo Croce Date: Mon, 17 Sep 2007 00:08:24 +0000 Subject: [PATCH] disable powersave, vlynq can't handle this SVN-Revision: 8818 --- package/acx-mac80211/patches/011-no_pm.patch | 32 +++++++++++++++++++ package/acx/patches/011-no_pm.patch | 33 ++++++++++++++++++++ 2 files changed, 65 insertions(+) create mode 100644 package/acx-mac80211/patches/011-no_pm.patch create mode 100644 package/acx/patches/011-no_pm.patch diff --git a/package/acx-mac80211/patches/011-no_pm.patch b/package/acx-mac80211/patches/011-no_pm.patch new file mode 100644 index 0000000000..09a00b04e5 --- /dev/null +++ b/package/acx-mac80211/patches/011-no_pm.patch @@ -0,0 +1,32 @@ +--- acx-mac80211-20070610/pci.c 2007-06-10 20:23:27.000000000 +0200 ++++ acx-mac80211-20070610.new/pci.c 2007-09-17 01:07:38.000000000 +0200 +@@ -1693,7 +1693,9 @@ + /** done with board specific setup **/ + + /* need to be able to restore PCI state after a suspend */ ++#ifdef CONFIG_PM + pci_save_state(pdev); ++#endif + + + acx_init_task_scheduler(adev); +@@ -1740,7 +1742,9 @@ + pci_disable_device(pdev); + fail_pci_enable_device: + ++#ifdef CONFIG_PM + pci_set_power_state(pdev, PCI_D3hot); ++#endif + fail_register_netdev: + ieee80211_free_hw(ieee); + done: +@@ -1872,7 +1876,9 @@ + ieee80211_free_hw(adev->ieee); + + /* put device into ACPI D3 mode (shutdown) */ ++#ifdef CONFIG_PM + pci_set_power_state(pdev, PCI_D3hot); ++#endif + // kfree(ieee); + end: + FN_EXIT0; diff --git a/package/acx/patches/011-no_pm.patch b/package/acx/patches/011-no_pm.patch new file mode 100644 index 0000000000..d1d0feb2f8 --- /dev/null +++ b/package/acx/patches/011-no_pm.patch @@ -0,0 +1,33 @@ +diff -ruN acx-20070610-old/pci.c acx-20070610-new/pci.c +--- acx-20070610-old/pci.c 2007-09-16 17:57:55.000000000 +0200 ++++ acx-20070610-new/pci.c 2007-09-16 17:59:25.000000000 +0200 +@@ -1630,7 +1630,9 @@ + log(L_IRQ|L_INIT, "using IRQ %d\n", pdev->irq); + + /* need to be able to restore PCI state after a suspend */ ++#ifdef CONFIG_PM + pci_save_state(pdev); ++#endif + pci_set_drvdata(pdev, ndev); + + /* ok, pci setup is finished, now start initializing the card */ +@@ -1728,7 +1730,9 @@ + pci_disable_device(pdev); + fail_pci_enable_device: + ++#ifdef CONFIG_PM + pci_set_power_state(pdev, PCI_D3hot); ++#endif + + done: + FN_EXIT1(result); +@@ -1848,7 +1852,9 @@ + free_netdev(ndev); + + /* put device into ACPI D3 mode (shutdown) */ ++#ifdef CONFIG_PM + pci_set_power_state(pdev, PCI_D3hot); ++#endif + + end: + FN_EXIT0; -- 2.30.2