From 7e21ce8e2b0b73f145af96958511f761544942d7 Mon Sep 17 00:00:00 2001 From: Sven Hauer Date: Mon, 27 Jun 2022 22:25:12 +0200 Subject: [PATCH] ath79: support for TP-Link EAP225 v4 MIME-Version: 1.0 Content-Type: text/plain; charset=utf8 Content-Transfer-Encoding: 8bit This model is almost identical to the EAP225 v3. Major difference is the RTL8211FS PHY Chipset. Device specifications: * SoC: QCA9563 @ 775MHz * RAM: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n, 3x3 * Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO * Ethernet (RTL8211FS): 1× 1GbE, 802.3at PoE Flashing instructions: * ssh into target device and run `cliclientd stopcs` * Upgrade with factory image via web interface Debricking: * Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC) * Bridge unpopulated resistors R225 (TXD) and R237 (RXD). Do NOT bridge R230. * Use 3.3V, 115200 baud, 8n1 * Interrupt bootloader by holding CTRL+B during boot * tftp initramfs to flash via LuCI web interface setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. Signed-off-by: Sven Hauer --- .../ath79/dts/qca9563_tplink_eap225-v4.dts | 59 +++++++++++++++++++ .../generic/base-files/etc/board.d/02_network | 1 + target/linux/ath79/image/generic-tp-link.mk | 11 ++++ 3 files changed, 71 insertions(+) create mode 100644 target/linux/ath79/dts/qca9563_tplink_eap225-v4.dts diff --git a/target/linux/ath79/dts/qca9563_tplink_eap225-v4.dts b/target/linux/ath79/dts/qca9563_tplink_eap225-v4.dts new file mode 100644 index 0000000000..ae27ff7068 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_tplink_eap225-v4.dts @@ -0,0 +1,59 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca9563_tplink_eap2x5-1port.dtsi" + +/ { + compatible = "tplink,eap225-v4", "qca,qca9563"; + model = "TP-Link EAP225 v4"; + + aliases { + led-boot = &led_status_green; + led-failsafe = &led_status_amber; + led-running = &led_status_green; + led-upgrade = &led_status_amber; + }; + + leds { + compatible = "gpio-leds"; + + led_status_green: status_green { + label = "green:status"; + gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + led_status_amber: status_amber { + label = "amber:status"; + gpios = <&gpio 9 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&art { + precalibration_ath10k: pre-calibration@5000 { + reg = <0x5000 0x2f20>; + }; +}; + +ð0 { + phy-handle = <&phy6>; + phy-mode = "sgmii"; +}; + +&mdio0 { + phy6: ethernet-phy@6 { + reg = <6>; + }; +}; + +&pcie { + wifi@0,0 { + compatible = "qcom,ath10k"; + reg = <0 0 0 0 0>; + + mac-address-increment = <1>; + + nvmem-cells = <&macaddr_info_8>, <&precalibration_ath10k>; + nvmem-cell-names = "mac-address", "pre-calibration"; + }; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 42ab19b47a..7ba39c4c49 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -79,6 +79,7 @@ ath79_setup_interfaces() tplink,eap225-outdoor-v3|\ tplink,eap225-v1|\ tplink,eap225-v3|\ + tplink,eap225-v4|\ tplink,eap245-v1|\ tplink,re350k-v1|\ tplink,re355-v1|\ diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk index ffe999660a..6d9ba2cd40 100644 --- a/target/linux/ath79/image/generic-tp-link.mk +++ b/target/linux/ath79/image/generic-tp-link.mk @@ -434,6 +434,17 @@ define Device/tplink_eap225-v3 endef TARGET_DEVICES += tplink_eap225-v3 +define Device/tplink_eap225-v4 + $(Device/tplink-eap2x5) + SOC := qca9563 + IMAGE_SIZE := 13824k + DEVICE_MODEL := EAP225 + DEVICE_VARIANT := v4 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct + TPLINK_BOARD_ID := EAP225-V3 +endef +TARGET_DEVICES += tplink_eap225-v4 + define Device/tplink_eap225-wall-v2 $(Device/tplink-eap2x5) SOC := qca9561 -- 2.30.2