From da970d63fb52fb50915f7f94aaf1d8e0b158b7d3 Mon Sep 17 00:00:00 2001 From: Daniel Golle Date: Mon, 4 Dec 2023 23:41:39 +0000 Subject: [PATCH] mediatek: switch to Linux version 6.1 Drop support for Linux 5.15 and switch to Linux 6.1. Signed-off-by: Daniel Golle --- target/linux/mediatek/Makefile | 3 +- .../mt7981-rfb-mxl-2p5g-phy-eth1.dtso | 32 - .../mt7981-rfb-mxl-2p5g-phy-swp5.dtso | 33 - .../dts/mediatek/mt7981-rfb-spim-nand.dtso | 66 - .../arm64/boot/dts/mediatek/mt7981-rfb.dts | 188 -- .../arch/arm64/boot/dts/mediatek/mt7981.dtsi | 820 --------- .../mt7986a-bananapi-bpi-r3-emmc.dtso | 29 - .../mt7986a-bananapi-bpi-r3-nand.dtso | 55 - .../mediatek/mt7986a-bananapi-bpi-r3-nor.dtso | 63 - .../mediatek/mt7986a-bananapi-bpi-r3-sd.dtso | 23 - .../dts/mediatek/mt7986a-bananapi-bpi-r3.dts | 501 ------ .../dts/mediatek/mt7986a-rfb-spim-nand.dts | 52 - .../dts/mediatek/mt7986a-rfb-spim-nor.dts | 51 - .../arm64/boot/dts/mediatek/mt7986a-rfb.dtsi | 389 ----- .../arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 645 ------- .../arm64/boot/dts/mediatek/mt7986b-rfb.dts | 194 --- .../arch/arm64/boot/dts/mediatek/mt7986b.dtsi | 15 - .../boot/dts/mediatek/mt7988a-rfb-emmc.dtso | 33 - .../dts/mediatek/mt7988a-rfb-eth1-aqr.dtso | 41 - .../mediatek/mt7988a-rfb-eth1-i2p5g-phy.dtso | 30 - .../dts/mediatek/mt7988a-rfb-eth1-mxl.dtso | 39 - .../dts/mediatek/mt7988a-rfb-eth1-sfp.dtso | 47 - .../dts/mediatek/mt7988a-rfb-eth2-aqr.dtso | 41 - .../dts/mediatek/mt7988a-rfb-eth2-mxl.dtso | 39 - .../dts/mediatek/mt7988a-rfb-eth2-sfp.dtso | 47 - .../boot/dts/mediatek/mt7988a-rfb-sd.dtso | 31 - .../dts/mediatek/mt7988a-rfb-snfi-nand.dtso | 69 - .../dts/mediatek/mt7988a-rfb-spim-nand.dtso | 64 - .../dts/mediatek/mt7988a-rfb-spim-nor.dtso | 59 - .../arm64/boot/dts/mediatek/mt7988a-rfb.dts | 200 --- .../arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 1456 ---------------- .../drivers/clk/mediatek/clk-mt7981-apmixed.c | 102 -- .../drivers/clk/mediatek/clk-mt7981-eth.c | 139 -- .../clk/mediatek/clk-mt7981-infracfg.c | 235 --- .../clk/mediatek/clk-mt7981-topckgen.c | 450 ----- .../drivers/clk/mediatek/clk-mt7986-apmixed.c | 100 -- .../drivers/clk/mediatek/clk-mt7986-eth.c | 132 -- .../clk/mediatek/clk-mt7986-infracfg.c | 224 --- .../clk/mediatek/clk-mt7986-topckgen.c | 342 ---- .../drivers/clk/mediatek/clk-mt7988-apmixed.c | 113 -- .../drivers/clk/mediatek/clk-mt7988-eth.c | 299 ---- .../clk/mediatek/clk-mt7988-infracfg.c | 406 ----- .../clk/mediatek/clk-mt7988-topckgen.c | 522 ------ .../drivers/net/phy/mediatek-2p5ge.c | 262 --- .../drivers/pinctrl/mediatek/pinctrl-mt7981.c | 1041 ----------- .../drivers/pinctrl/mediatek/pinctrl-mt7986.c | 1011 ----------- .../drivers/pinctrl/mediatek/pinctrl-mt7988.c | 1466 ---------------- .../dt-bindings/clock/mediatek,mt7981-clk.h | 215 --- .../dt-bindings/clock/mediatek,mt7988-clk.h | 276 --- .../include/dt-bindings/clock/mt7986-clk.h | 169 -- .../include/dt-bindings/reset/mt7986-resets.h | 55 - target/linux/mediatek/filogic/config-5.15 | 443 ----- target/linux/mediatek/mt7622/config-5.15 | 444 ----- target/linux/mediatek/mt7623/config-5.15 | 577 ------- target/linux/mediatek/mt7629/config-5.15 | 327 ---- .../041-block-fit-partition-parser.patch | 214 --- .../100-dts-update-mt7622-rfb1.patch | 119 -- .../101-dts-update-mt7629-rfb.patch | 60 - .../103-mt7623-enable-arch-timer.patch | 20 - .../104-mt7622-add-snor-irq.patch | 10 - .../105-dts-mt7622-enable-pstore.patch | 25 - .../110-dts-fix-bpi2-console.patch | 10 - .../111-dts-fix-bpi64-console.patch | 11 - .../112-dts-fix-bpi64-lan-names.patch | 37 - .../113-dts-fix-bpi64-leds-and-buttons.patch | 56 - .../114-dts-bpi64-disable-rtc.patch | 21 - .../115-dts-bpi64-add-snand-support.patch | 50 - ...-infrastructure-to-support-hardware-.patch | 214 --- ...ew-helper-to-retrieve-the-ECC-contex.patch | 31 - ...vide-a-helper-to-retrieve-a-pileline.patch | 73 - ...mem-Introduce-a-capability-structure.patch | 71 - ...ck-the-controller-extra-capabilities.patch | 51 - ...l-the-spi_mem_dtr_supports_op-helper.patch | 111 -- ...an-ecc-parameter-to-the-spi_mem_op-s.patch | 72 - ...lay-a-little-bit-the-dirmap-creation.patch | 50 - ...te-direct-mapping-descriptors-for-EC.patch | 98 -- ...nd-make-mtk_ecc.c-a-separated-module.patch | 1383 --------------- ...ver-for-MTK-SPI-NAND-Flash-Interface.patch | 1537 ----------------- ...-also-parse-nand-ecc-engine-if-avail.patch | 30 - ...dts-mediatek-add-mtk-snfi-for-mt7622.patch | 35 - .../121-hack-spi-nand-1b-bbm.patch | 20 - .../130-dts-mt7629-add-snand-support.patch | 94 - .../131-dts-mt7622-add-snand-support.patch | 68 - ...dts-fix-wmac-support-for-mt7622-rfb1.patch | 18 - ...s-mt7623-eip97-inside-secure-support.patch | 24 - .../160-dts-mt7623-bpi-r2-earlycon.patch | 11 - ...1-dts-mt7623-bpi-r2-mmc-device-order.patch | 11 - .../162-dts-mt7623-bpi-r2-led-aliases.patch | 29 - ...163-dts-mt7623-bpi-r2-ethernet-alias.patch | 10 - ...arm-dts-mt7623-add-musb-device-nodes.patch | 69 - ...80-dts-mt7622-bpi-r64-add-mt7531-irq.patch | 13 - ...-dts-mediatek-mt7622-fix-GICv2-range.patch | 106 -- ...mt7622-specify-the-L2-cache-topology.patch | 132 -- ...2-specify-the-number-of-DMA-requests.patch | 122 -- .../193-dts-mt7623-thermal_zone_fix.patch | 48 - .../194-dts-mt7968a-add-ramoops.patch | 17 - ...i-r3-leds-port-names-and-wifi-eeprom.patch | 196 --- ...-phy-phy-mtk-tphy-Add-hifsys-support.patch | 66 - ...-mediatek-add-support-for-MT7986-SoC.patch | 26 - ...k-Add-API-for-clock-resource-recycle.patch | 28 - ...lk-mediatek-add-mt7986-clock-support.patch | 39 - ...-spi-mediatek-add-mt7986-spi-support.patch | 917 ---------- ...lk-mediatek-add-mt7981-clock-support.patch | 39 - ...-mediatek-add-support-for-MT7981-SoC.patch | 26 - ...-mediatek-add-support-for-MT7988-SoC.patch | 26 - ...k-mediatek-Add-pcw-chg-shift-control.patch | 24 - ...lk-mediatek-add-mt7988-clock-support.patch | 31 - ...-mediatek-add-support-for-MT7986-SoC.patch | 44 - .../330-snand-mtk-bmt-support.patch | 34 - .../331-mt7622-rfb1-enable-bmt.patch | 10 - ...Add-support-for-the-Fidelix-FM35X1GA.patch | 122 -- ...-Cleanup-variables-and-error-handlin.patch | 166 -- ...ufreq-mediatek-Remove-unused-headers.patch | 25 - ...ediatek-Enable-clocks-and-regulators.patch | 117 -- ...diatek-Use-device-print-to-show-logs.patch | 161 -- ...freq-mediatek-Replace-old_-with-pre_.patch | 201 --- ...k-Record-previous-target-vproc-value.patch | 64 - ...ediatek-Make-sram-regulator-optional.patch | 30 - ...-Fix-NULL-pointer-dereference-in-med.patch | 32 - ...-Move-voltage-limits-to-platform-dat.patch | 227 --- ...-Refine-mtk_cpufreq_voltage_tracking.patch | 255 --- ...ediatek-Add-opp-notification-support.patch | 184 -- ...-Fix-potential-deadlock-problem-in-m.patch | 43 - ...freq-mediatek-Link-CCI-device-to-CPU.patch | 188 -- ...freq-mediatek-Add-support-for-MT8186.patch | 42 - ...-Handle-sram-regulator-probe-deferra.patch | 35 - ...-fix-error-return-code-in-mtk_cpu_dv.patch | 29 - ...mediatek-fix-passing-zero-to-PTR_ERR.patch | 47 - ...-fix-KP-caused-by-handler-usage-afte.patch | 149 -- ...-raise-proc-sram-max-voltage-for-MT8.patch | 55 - ...-Raise-proc-and-sram-max-voltage-for.patch | 58 - ...freq-mediatek-Add-support-for-MT7988.patch | 41 - ...-correct-voltages-for-MT7622-and-MT7.patch | 53 - ...ypto-add-eip97-inside-secure-support.patch | 27 - ...01-crypto-fix-eip97-cache-incoherent.patch | 26 - .../405-mt7986-trng-add-rng-support.patch | 41 - .../patches-5.15/410-bt-mtk-serial-fix.patch | 33 - ...or-add-support-for-Winbond-W25Q512JV.patch | 28 - ...xx-Move-chip_config-to-driver-s-priv.patch | 130 -- ...-Add-support-for-dynamic-calibration.patch | 236 --- ...ers-spi-mem-Add-spi-calibration-hook.patch | 41 - ...xx-Add-controller-s-calibration-para.patch | 43 - ...and-Add-calibration-support-for-spin.patch | 81 - ...nor-Add-calibration-support-for-spi-.patch | 57 - .../500-gsw-rtl8367s-mt7622-support.patch | 25 - ...ek-Split-PCIe-node-for-MT2712-and-MT.patch | 332 ---- ...ert-PERST-for-100ms-for-power-and-cl.patch | 34 - ...s-mediatek-add-mt7622-pcie-slot-node.patch | 28 - ...dts-mediatek-Update-mt7629-PCIe-node.patch | 203 --- ...diatek-fix-clearing-interrupt-status.patch | 23 - ...1-pcie-mediatek-gen3-PERST-for-100ms.patch | 17 - ...pers-to-extract-clause-45-regad-and-.patch | 53 - ..._eth_soc-implement-Clause-45-MDIO-ac.patch | 128 -- ...ediatek-add-support-for-coherent-DMA.patch | 82 - .../721-dts-mt7622-mediatek-fix-300mhz.patch | 27 - .../722-remove-300Hz-to-prevent-freeze.patch | 25 - ...er-for-MediaTek-SoC-built-in-GE-PHYs.patch | 1204 ------------- ...-ge-soc-initialize-MT7988-PHY-LEDs-d.patch | 213 --- ...-don-t-use-SGMII-AN-if-using-phylink.patch | 63 - ...phy-add-driver-for-MediaTek-2.5G-PHY.patch | 39 - ...-ge-soc-sync-driver-with-MediaTek-SD.patch | 270 --- ...k-tphy-Add-PCIe-2-lane-efuse-support.patch | 225 --- ...-add-auto-load-valid-check-mechanism.patch | 149 -- .../804-pwm-add-mt7986-support.patch | 23 - ...mtk-use-function-pointer-for-raw_to_.patch | 56 - ...ek-add-support-for-MT7986-and-MT7981.patch | 240 --- ...-pwm-mediatek-Add-support-for-MT7981.patch | 122 -- ...dings-pinctrl-mt8195-add-rsel-define.patch | 33 - ...-moore-check-if-pin_desc-is-valid-be.patch | 93 - ...inctrl-mediatek-support-rsel-feature.patch | 457 ----- ...-add-a-check-for-error-in-mtk_pincon.patch | 31 - ...-Fix-EINT-pins-input-debounce-time-c.patch | 297 ---- ...mediatek-Export-debounce-time-tables.patch | 37 - ...-extend-pinctrl-moore-to-support-new.patch | 129 -- ...dd-bindings-for-Richtek-RT5190A-PMIC.patch | 180 -- ...a-Add-support-for-Richtek-RT5190A-PM.patch | 562 ------ ...et-the-handshake-signal-between-i2c-.patch | 74 - ...p-i2c-dma-register-when-a-timeout-oc.patch | 102 -- ...d-i2c-compatible-for-Mediatek-MT8186.patch | 45 - ...modify-bus-speed-calculation-formula.patch | 132 -- ...mediatek-remove-redundant-null-check.patch | 41 - ...18-i2c-mt65xx-Simplify-with-clk-bulk.patch | 234 --- ...d-i2c-compatible-for-Mediatek-MT8168.patch | 46 - ...imize-master_xfer-and-avoid-circular.patch | 101 -- ...-an-error-handling-path-in-mtk_i2c_p.patch | 48 - ...diatek-add-i2c-compatible-for-MT8188.patch | 82 - ...move-drivers-from-strlcpy-to-strscpy.patch | 579 ------- ...v6.2-i2c-mediatek-add-mt7986-support.patch | 44 - ...evm_platform_get_and_ioremap_resourc.patch | 42 - ...t65xx-drop-of_match_ptr-for-ID-table.patch | 33 - ...-mediatek-add-support-for-MT7981-SoC.patch | 47 - ...i2c-mt65xx-allow-optional-pmic-clock.patch | 45 - ...oC-mediatek-mt7986-add-common-header.patch | 269 --- ...7986-support-etdm-in-platform-driver.patch | 430 ----- ...-mediatek-mt7986-add-platform-driver.patch | 685 -------- ...t7986-add-machine-driver-with-wm8960.patch | 243 --- ...-mediatek-mt7986-wm8960-add-mt7986-w.patch | 87 - ...-mediatek-mt7986-afe-add-audio-afe-d.patch | 180 -- ...7986-drop-the-remove-callback-of-mt7.patch | 42 - ...7986-remove-the-mt7986_wm8960_priv-s.patch | 105 -- ...iatek-mt7986-add-sample-rate-checker.patch | 49 - ...7986-silence-error-in-case-of-EPROBE.patch | 26 - .../862-arm64-dts-mt7986-add-afe.patch | 40 - ...63-arm64-dts-mt7986-add-sound-wm8960.patch | 61 - ...-mt7986-add-sound-overlay-for-bpi-r3.patch | 65 - ...mt7622-bpi-r64-aliases-for-dtoverlay.patch | 65 - .../901-arm-add-cmdline-override.patch | 54 - .../910-dts-mt7622-bpi-r64-wifi-eeprom.patch | 31 - ...g-mtk-add-disable_wdt_extrst-support.patch | 50 - ...t-mt7986-Add-toprgu-reset-controller.patch | 49 - ...3-change-driver-name-to-mtk-pcie-gen.patch | 20 - .../930-spi-mt65xx-enable-sel-clk.patch | 29 - ..._wed-rename-mtk_wed_get_memory_regio.patch | 37 - ...986-move-cpuboot-in-a-dedicated-node.patch | 66 - ..._wed-move-cpuboot-in-a-dedicated-dts.patch | 81 - ...tk_wed-move-ilm-a-dedicated-dts-node.patch | 86 - ...tk_wed-move-dlm-a-dedicated-dts-node.patch | 57 - ...-mt7986-move-ilm-in-a-dedicated-node.patch | 83 - ...-mt7986-move-dlm-in-a-dedicated-node.patch | 81 - .../950-smartrg-i2c-led-driver.patch | 34 - ...iatek-split-tx-and-rx-fields-in-mtk_.patch | 599 ------- ...iatek-use-QDMA-instead-of-ADMAv2-on-.patch | 123 -- ...ernet-mtk_eth_soc-fix-WED-wifi-reset.patch | 49 - 223 files changed, 1 insertion(+), 35429 deletions(-) delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981-rfb-mxl-2p5g-phy-eth1.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981-rfb-mxl-2p5g-phy-swp5.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981-rfb-spim-nand.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981-rfb.dts delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981.dtsi delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-rfb-spim-nand.dts delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-rfb-spim-nor.dts delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dtsi delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a.dtsi delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986b.dtsi delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-emmc.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth1-aqr.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth1-i2p5g-phy.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth1-mxl.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth1-sfp.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth2-aqr.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth2-mxl.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth2-sfp.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-sd.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-snfi-nand.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-spim-nand.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-spim-nor.dtso delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb.dts delete mode 100644 target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a.dtsi delete mode 100644 target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7981-apmixed.c delete mode 100644 target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7981-eth.c delete mode 100644 target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7981-infracfg.c delete mode 100644 target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7981-topckgen.c delete mode 100644 target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7986-apmixed.c delete mode 100644 target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7986-eth.c delete mode 100644 target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7986-infracfg.c delete mode 100644 target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7986-topckgen.c delete mode 100644 target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7988-apmixed.c delete mode 100644 target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7988-eth.c delete mode 100644 target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7988-infracfg.c delete mode 100644 target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7988-topckgen.c delete mode 100644 target/linux/mediatek/files-5.15/drivers/net/phy/mediatek-2p5ge.c delete mode 100644 target/linux/mediatek/files-5.15/drivers/pinctrl/mediatek/pinctrl-mt7981.c delete mode 100644 target/linux/mediatek/files-5.15/drivers/pinctrl/mediatek/pinctrl-mt7986.c delete mode 100644 target/linux/mediatek/files-5.15/drivers/pinctrl/mediatek/pinctrl-mt7988.c delete mode 100644 target/linux/mediatek/files-5.15/include/dt-bindings/clock/mediatek,mt7981-clk.h delete mode 100644 target/linux/mediatek/files-5.15/include/dt-bindings/clock/mediatek,mt7988-clk.h delete mode 100644 target/linux/mediatek/files-5.15/include/dt-bindings/clock/mt7986-clk.h delete mode 100644 target/linux/mediatek/files-5.15/include/dt-bindings/reset/mt7986-resets.h delete mode 100644 target/linux/mediatek/filogic/config-5.15 delete mode 100644 target/linux/mediatek/mt7622/config-5.15 delete mode 100644 target/linux/mediatek/mt7623/config-5.15 delete mode 100644 target/linux/mediatek/mt7629/config-5.15 delete mode 100644 target/linux/mediatek/patches-5.15/041-block-fit-partition-parser.patch delete mode 100644 target/linux/mediatek/patches-5.15/100-dts-update-mt7622-rfb1.patch delete mode 100644 target/linux/mediatek/patches-5.15/101-dts-update-mt7629-rfb.patch delete mode 100644 target/linux/mediatek/patches-5.15/103-mt7623-enable-arch-timer.patch delete mode 100644 target/linux/mediatek/patches-5.15/104-mt7622-add-snor-irq.patch delete mode 100644 target/linux/mediatek/patches-5.15/105-dts-mt7622-enable-pstore.patch delete mode 100644 target/linux/mediatek/patches-5.15/110-dts-fix-bpi2-console.patch delete mode 100644 target/linux/mediatek/patches-5.15/111-dts-fix-bpi64-console.patch delete mode 100644 target/linux/mediatek/patches-5.15/112-dts-fix-bpi64-lan-names.patch delete mode 100644 target/linux/mediatek/patches-5.15/113-dts-fix-bpi64-leds-and-buttons.patch delete mode 100644 target/linux/mediatek/patches-5.15/114-dts-bpi64-disable-rtc.patch delete mode 100644 target/linux/mediatek/patches-5.15/115-dts-bpi64-add-snand-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/120-01-v5.18-mtd-nand-ecc-Add-infrastructure-to-support-hardware-.patch delete mode 100644 target/linux/mediatek/patches-5.15/120-02-v5.18-mtd-nand-Add-a-new-helper-to-retrieve-the-ECC-contex.patch delete mode 100644 target/linux/mediatek/patches-5.15/120-03-v5.18-mtd-nand-ecc-Provide-a-helper-to-retrieve-a-pileline.patch delete mode 100644 target/linux/mediatek/patches-5.15/120-04-v5.18-spi-spi-mem-Introduce-a-capability-structure.patch delete mode 100644 target/linux/mediatek/patches-5.15/120-05-v5.18-spi-spi-mem-Check-the-controller-extra-capabilities.patch delete mode 100644 target/linux/mediatek/patches-5.15/120-06-v5.18-spi-spi-mem-Kill-the-spi_mem_dtr_supports_op-helper.patch delete mode 100644 target/linux/mediatek/patches-5.15/120-07-v5.18-spi-spi-mem-Add-an-ecc-parameter-to-the-spi_mem_op-s.patch delete mode 100644 target/linux/mediatek/patches-5.15/120-08-v5.18-mtd-spinand-Delay-a-little-bit-the-dirmap-creation.patch delete mode 100644 target/linux/mediatek/patches-5.15/120-09-v5.18-mtd-spinand-Create-direct-mapping-descriptors-for-EC.patch delete mode 100644 target/linux/mediatek/patches-5.15/120-11-v5.19-mtd-nand-make-mtk_ecc.c-a-separated-module.patch delete mode 100644 target/linux/mediatek/patches-5.15/120-12-v5.19-spi-add-driver-for-MTK-SPI-NAND-Flash-Interface.patch delete mode 100644 target/linux/mediatek/patches-5.15/120-13-v5.19-mtd-nand-mtk-ecc-also-parse-nand-ecc-engine-if-avail.patch delete mode 100644 target/linux/mediatek/patches-5.15/120-14-v5.19-arm64-dts-mediatek-add-mtk-snfi-for-mt7622.patch delete mode 100644 target/linux/mediatek/patches-5.15/121-hack-spi-nand-1b-bbm.patch delete mode 100644 target/linux/mediatek/patches-5.15/130-dts-mt7629-add-snand-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/131-dts-mt7622-add-snand-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/140-dts-fix-wmac-support-for-mt7622-rfb1.patch delete mode 100644 target/linux/mediatek/patches-5.15/150-dts-mt7623-eip97-inside-secure-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/160-dts-mt7623-bpi-r2-earlycon.patch delete mode 100644 target/linux/mediatek/patches-5.15/161-dts-mt7623-bpi-r2-mmc-device-order.patch delete mode 100644 target/linux/mediatek/patches-5.15/162-dts-mt7623-bpi-r2-led-aliases.patch delete mode 100644 target/linux/mediatek/patches-5.15/163-dts-mt7623-bpi-r2-ethernet-alias.patch delete mode 100644 target/linux/mediatek/patches-5.15/173-arm-dts-mt7623-add-musb-device-nodes.patch delete mode 100644 target/linux/mediatek/patches-5.15/180-dts-mt7622-bpi-r64-add-mt7531-irq.patch delete mode 100644 target/linux/mediatek/patches-5.15/190-arm64-dts-mediatek-mt7622-fix-GICv2-range.patch delete mode 100644 target/linux/mediatek/patches-5.15/191-v5.19-arm64-dts-mt7622-specify-the-L2-cache-topology.patch delete mode 100644 target/linux/mediatek/patches-5.15/192-v5.19-arm64-dts-mt7622-specify-the-number-of-DMA-requests.patch delete mode 100644 target/linux/mediatek/patches-5.15/193-dts-mt7623-thermal_zone_fix.patch delete mode 100644 target/linux/mediatek/patches-5.15/194-dts-mt7968a-add-ramoops.patch delete mode 100644 target/linux/mediatek/patches-5.15/195-dts-mt7986a-bpi-r3-leds-port-names-and-wifi-eeprom.patch delete mode 100644 target/linux/mediatek/patches-5.15/200-phy-phy-mtk-tphy-Add-hifsys-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/210-v6.1-pinctrl-mediatek-add-support-for-MT7986-SoC.patch delete mode 100644 target/linux/mediatek/patches-5.15/211-v5.16-clk-mediatek-Add-API-for-clock-resource-recycle.patch delete mode 100644 target/linux/mediatek/patches-5.15/212-v5.17-clk-mediatek-add-mt7986-clock-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/213-spi-mediatek-add-mt7986-spi-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/214-v6.3-clk-mediatek-add-mt7981-clock-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/215-v6.3-pinctrl-mediatek-add-support-for-MT7981-SoC.patch delete mode 100644 target/linux/mediatek/patches-5.15/240-pinctrl-mediatek-add-support-for-MT7988-SoC.patch delete mode 100644 target/linux/mediatek/patches-5.15/241-clk-mediatek-Add-pcw-chg-shift-control.patch delete mode 100644 target/linux/mediatek/patches-5.15/242-clk-mediatek-add-mt7988-clock-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/320-mmc-mediatek-add-support-for-MT7986-SoC.patch delete mode 100644 target/linux/mediatek/patches-5.15/330-snand-mtk-bmt-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/331-mt7622-rfb1-enable-bmt.patch delete mode 100644 target/linux/mediatek/patches-5.15/340-mtd-spinand-Add-support-for-the-Fidelix-FM35X1GA.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-01-cpufreq-mediatek-Cleanup-variables-and-error-handlin.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-02-cpufreq-mediatek-Remove-unused-headers.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-03-cpufreq-mediatek-Enable-clocks-and-regulators.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-04-cpufreq-mediatek-Use-device-print-to-show-logs.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-05-cpufreq-mediatek-Replace-old_-with-pre_.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-06-cpufreq-mediatek-Record-previous-target-vproc-value.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-07-cpufreq-mediatek-Make-sram-regulator-optional.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-08-cpufreq-mediatek-Fix-NULL-pointer-dereference-in-med.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-09-cpufreq-mediatek-Move-voltage-limits-to-platform-dat.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-10-cpufreq-mediatek-Refine-mtk_cpufreq_voltage_tracking.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-11-cpufreq-mediatek-Add-opp-notification-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-12-cpufreq-mediatek-Fix-potential-deadlock-problem-in-m.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-13-cpufreq-mediatek-Link-CCI-device-to-CPU.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-14-cpufreq-mediatek-Add-support-for-MT8186.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-15-cpufreq-mediatek-Handle-sram-regulator-probe-deferra.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-16-cpufreq-mediatek-fix-error-return-code-in-mtk_cpu_dv.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-17-cpufreq-mediatek-fix-passing-zero-to-PTR_ERR.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-18-cpufreq-mediatek-fix-KP-caused-by-handler-usage-afte.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-19-cpufreq-mediatek-raise-proc-sram-max-voltage-for-MT8.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-20-cpufreq-mediatek-Raise-proc-and-sram-max-voltage-for.patch delete mode 100644 target/linux/mediatek/patches-5.15/350-21-cpufreq-mediatek-Add-support-for-MT7988.patch delete mode 100644 target/linux/mediatek/patches-5.15/351-cpufreq-mediatek-correct-voltages-for-MT7622-and-MT7.patch delete mode 100644 target/linux/mediatek/patches-5.15/400-crypto-add-eip97-inside-secure-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/401-crypto-fix-eip97-cache-incoherent.patch delete mode 100644 target/linux/mediatek/patches-5.15/405-mt7986-trng-add-rng-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/410-bt-mtk-serial-fix.patch delete mode 100644 target/linux/mediatek/patches-5.15/420-mtd-spi-nor-add-support-for-Winbond-W25Q512JV.patch delete mode 100644 target/linux/mediatek/patches-5.15/431-drivers-spi-mt65xx-Move-chip_config-to-driver-s-priv.patch delete mode 100644 target/linux/mediatek/patches-5.15/432-drivers-spi-Add-support-for-dynamic-calibration.patch delete mode 100644 target/linux/mediatek/patches-5.15/433-drivers-spi-mem-Add-spi-calibration-hook.patch delete mode 100644 target/linux/mediatek/patches-5.15/434-drivers-spi-mt65xx-Add-controller-s-calibration-para.patch delete mode 100644 target/linux/mediatek/patches-5.15/435-drivers-mtd-spinand-Add-calibration-support-for-spin.patch delete mode 100644 target/linux/mediatek/patches-5.15/436-drivers-mtd-spi-nor-Add-calibration-support-for-spi-.patch delete mode 100644 target/linux/mediatek/patches-5.15/500-gsw-rtl8367s-mt7622-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/600-v5.16-arm64-dts-mediatek-Split-PCIe-node-for-MT2712-and-MT.patch delete mode 100644 target/linux/mediatek/patches-5.15/601-PCI-mediatek-Assert-PERST-for-100ms-for-power-and-cl.patch delete mode 100644 target/linux/mediatek/patches-5.15/602-arm64-dts-mediatek-add-mt7622-pcie-slot-node.patch delete mode 100644 target/linux/mediatek/patches-5.15/603-v5.16-ARM-dts-mediatek-Update-mt7629-PCIe-node.patch delete mode 100644 target/linux/mediatek/patches-5.15/610-pcie-mediatek-fix-clearing-interrupt-status.patch delete mode 100644 target/linux/mediatek/patches-5.15/611-pcie-mediatek-gen3-PERST-for-100ms.patch delete mode 100644 target/linux/mediatek/patches-5.15/702-v5.17-net-mdio-add-helpers-to-extract-clause-45-regad-and-.patch delete mode 100644 target/linux/mediatek/patches-5.15/703-v5.17-net-ethernet-mtk_eth_soc-implement-Clause-45-MDIO-ac.patch delete mode 100644 target/linux/mediatek/patches-5.15/710-pci-pcie-mediatek-add-support-for-coherent-DMA.patch delete mode 100644 target/linux/mediatek/patches-5.15/721-dts-mt7622-mediatek-fix-300mhz.patch delete mode 100644 target/linux/mediatek/patches-5.15/722-remove-300Hz-to-prevent-freeze.patch delete mode 100644 target/linux/mediatek/patches-5.15/730-v6.5-net-phy-add-driver-for-MediaTek-SoC-built-in-GE-PHYs.patch delete mode 100644 target/linux/mediatek/patches-5.15/731-net-phy-mediatek-ge-soc-initialize-MT7988-PHY-LEDs-d.patch delete mode 100644 target/linux/mediatek/patches-5.15/732-net-phy-mxl-gpy-don-t-use-SGMII-AN-if-using-phylink.patch delete mode 100644 target/linux/mediatek/patches-5.15/733-net-phy-add-driver-for-MediaTek-2.5G-PHY.patch delete mode 100644 target/linux/mediatek/patches-5.15/734-net-phy-mediatek-ge-soc-sync-driver-with-MediaTek-SD.patch delete mode 100644 target/linux/mediatek/patches-5.15/801-phy-phy-mtk-tphy-Add-PCIe-2-lane-efuse-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/802-phy-phy-mtk-tphy-add-auto-load-valid-check-mechanism.patch delete mode 100644 target/linux/mediatek/patches-5.15/804-pwm-add-mt7986-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/805-v6.2-thermal-drivers-mtk-use-function-pointer-for-raw_to_.patch delete mode 100644 target/linux/mediatek/patches-5.15/806-v6.2-thermal-mediatek-add-support-for-MT7986-and-MT7981.patch delete mode 100644 target/linux/mediatek/patches-5.15/811-pwm-mediatek-Add-support-for-MT7981.patch delete mode 100644 target/linux/mediatek/patches-5.15/820-v5.16-dt-bindings-pinctrl-mt8195-add-rsel-define.patch delete mode 100644 target/linux/mediatek/patches-5.15/821-v5.16-pinctrl-mediatek-moore-check-if-pin_desc-is-valid-be.patch delete mode 100644 target/linux/mediatek/patches-5.15/822-v5.16-pinctrl-mediatek-support-rsel-feature.patch delete mode 100644 target/linux/mediatek/patches-5.15/823-v5.17-pinctrl-mediatek-add-a-check-for-error-in-mtk_pincon.patch delete mode 100644 target/linux/mediatek/patches-5.15/824-v6.1-pinctrl-mediatek-Fix-EINT-pins-input-debounce-time-c.patch delete mode 100644 target/linux/mediatek/patches-5.15/825-v6.1-pinctrl-mediatek-Export-debounce-time-tables.patch delete mode 100644 target/linux/mediatek/patches-5.15/826-v6.2-pinctrl-mediatek-extend-pinctrl-moore-to-support-new.patch delete mode 100644 target/linux/mediatek/patches-5.15/830-v5.18-regulator-Add-bindings-for-Richtek-RT5190A-PMIC.patch delete mode 100644 target/linux/mediatek/patches-5.15/831-v5.18-regulator-rt5190a-Add-support-for-Richtek-RT5190A-PM.patch delete mode 100644 target/linux/mediatek/patches-5.15/840-v5.16-i2c-mediatek-Reset-the-handshake-signal-between-i2c-.patch delete mode 100644 target/linux/mediatek/patches-5.15/841-v5.16-i2c-mediatek-Dump-i2c-dma-register-when-a-timeout-oc.patch delete mode 100644 target/linux/mediatek/patches-5.15/842-v5.18-i2c-mediatek-Add-i2c-compatible-for-Mediatek-MT8186.patch delete mode 100644 target/linux/mediatek/patches-5.15/843-v5.18-i2c-mediatek-modify-bus-speed-calculation-formula.patch delete mode 100644 target/linux/mediatek/patches-5.15/844-v5.18-i2c-mediatek-remove-redundant-null-check.patch delete mode 100644 target/linux/mediatek/patches-5.15/845-v5.18-i2c-mt65xx-Simplify-with-clk-bulk.patch delete mode 100644 target/linux/mediatek/patches-5.15/846-v5.18-i2c-mediatek-Add-i2c-compatible-for-Mediatek-MT8168.patch delete mode 100644 target/linux/mediatek/patches-5.15/847-v5.19-i2c-mediatek-Optimize-master_xfer-and-avoid-circular.patch delete mode 100644 target/linux/mediatek/patches-5.15/848-v5.19-i2c-mediatek-Fix-an-error-handling-path-in-mtk_i2c_p.patch delete mode 100644 target/linux/mediatek/patches-5.15/849-v6.0-i2c-mediatek-add-i2c-compatible-for-MT8188.patch delete mode 100644 target/linux/mediatek/patches-5.15/850-v6.0-i2c-move-drivers-from-strlcpy-to-strscpy.patch delete mode 100644 target/linux/mediatek/patches-5.15/851-v6.2-i2c-mediatek-add-mt7986-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/852-v6.3-i2c-mt65xx-Use-devm_platform_get_and_ioremap_resourc.patch delete mode 100644 target/linux/mediatek/patches-5.15/853-v6.3-i2c-mt65xx-drop-of_match_ptr-for-ID-table.patch delete mode 100644 target/linux/mediatek/patches-5.15/854-v6.4-i2c-mediatek-add-support-for-MT7981-SoC.patch delete mode 100644 target/linux/mediatek/patches-5.15/855-i2c-mt65xx-allow-optional-pmic-clock.patch delete mode 100644 target/linux/mediatek/patches-5.15/860-v6.6-01-ASoC-mediatek-mt7986-add-common-header.patch delete mode 100644 target/linux/mediatek/patches-5.15/860-v6.6-02-ASoC-mediatek-mt7986-support-etdm-in-platform-driver.patch delete mode 100644 target/linux/mediatek/patches-5.15/860-v6.6-03-ASoC-mediatek-mt7986-add-platform-driver.patch delete mode 100644 target/linux/mediatek/patches-5.15/860-v6.6-04-ASoC-mediatek-mt7986-add-machine-driver-with-wm8960.patch delete mode 100644 target/linux/mediatek/patches-5.15/860-v6.6-05-ASoC-dt-bindings-mediatek-mt7986-wm8960-add-mt7986-w.patch delete mode 100644 target/linux/mediatek/patches-5.15/860-v6.6-06-ASoC-dt-bindings-mediatek-mt7986-afe-add-audio-afe-d.patch delete mode 100644 target/linux/mediatek/patches-5.15/860-v6.7-07-ASoC-mediatek-mt7986-drop-the-remove-callback-of-mt7.patch delete mode 100644 target/linux/mediatek/patches-5.15/860-v6.7-08-ASoC-mediatek-mt7986-remove-the-mt7986_wm8960_priv-s.patch delete mode 100644 target/linux/mediatek/patches-5.15/860-v6.7-09-ASoC-mediatek-mt7986-add-sample-rate-checker.patch delete mode 100644 target/linux/mediatek/patches-5.15/861-pending-10-ASoC-mediatek-mt7986-silence-error-in-case-of-EPROBE.patch delete mode 100644 target/linux/mediatek/patches-5.15/862-arm64-dts-mt7986-add-afe.patch delete mode 100644 target/linux/mediatek/patches-5.15/863-arm64-dts-mt7986-add-sound-wm8960.patch delete mode 100644 target/linux/mediatek/patches-5.15/864-arm64-dts-mt7986-add-sound-overlay-for-bpi-r3.patch delete mode 100644 target/linux/mediatek/patches-5.15/900-dts-mt7622-bpi-r64-aliases-for-dtoverlay.patch delete mode 100644 target/linux/mediatek/patches-5.15/901-arm-add-cmdline-override.patch delete mode 100644 target/linux/mediatek/patches-5.15/910-dts-mt7622-bpi-r64-wifi-eeprom.patch delete mode 100644 target/linux/mediatek/patches-5.15/920-v5.16-watchdog-mtk-add-disable_wdt_extrst-support.patch delete mode 100644 target/linux/mediatek/patches-5.15/921-v5.19-watchdog-mtk_wdt-mt7986-Add-toprgu-reset-controller.patch delete mode 100644 target/linux/mediatek/patches-5.15/922-v6.1-PCI-mediatek-gen3-change-driver-name-to-mtk-pcie-gen.patch delete mode 100644 target/linux/mediatek/patches-5.15/930-spi-mt65xx-enable-sel-clk.patch delete mode 100644 target/linux/mediatek/patches-5.15/940-net-ethernet-mtk_wed-rename-mtk_wed_get_memory_regio.patch delete mode 100644 target/linux/mediatek/patches-5.15/941-arm64-dts-mt7986-move-cpuboot-in-a-dedicated-node.patch delete mode 100644 target/linux/mediatek/patches-5.15/942-net-ethernet-mtk_wed-move-cpuboot-in-a-dedicated-dts.patch delete mode 100644 target/linux/mediatek/patches-5.15/943-net-ethernet-mtk_wed-move-ilm-a-dedicated-dts-node.patch delete mode 100644 target/linux/mediatek/patches-5.15/944-net-ethernet-mtk_wed-move-dlm-a-dedicated-dts-node.patch delete mode 100644 target/linux/mediatek/patches-5.15/945-arm64-dts-mt7986-move-ilm-in-a-dedicated-node.patch delete mode 100644 target/linux/mediatek/patches-5.15/946-arm64-dts-mt7986-move-dlm-in-a-dedicated-node.patch delete mode 100644 target/linux/mediatek/patches-5.15/950-smartrg-i2c-led-driver.patch delete mode 100644 target/linux/mediatek/patches-5.15/961-net-ethernet-mediatek-split-tx-and-rx-fields-in-mtk_.patch delete mode 100644 target/linux/mediatek/patches-5.15/962-net-ethernet-mediatek-use-QDMA-instead-of-ADMAv2-on-.patch delete mode 100644 target/linux/mediatek/patches-5.15/963-net-ethernet-mtk_eth_soc-fix-WED-wifi-reset.patch diff --git a/target/linux/mediatek/Makefile b/target/linux/mediatek/Makefile index f73f2daef6..279c167b83 100644 --- a/target/linux/mediatek/Makefile +++ b/target/linux/mediatek/Makefile @@ -8,8 +8,7 @@ BOARDNAME:=MediaTek Ralink ARM SUBTARGETS:=mt7622 mt7623 mt7629 filogic FEATURES:=dt-overlay emmc fpu gpio nand pci pcie rootfs-part separate_ramdisk squashfs usb -KERNEL_PATCHVER:=5.15 -KERNEL_TESTING_PATCHVER:=6.1 +KERNEL_PATCHVER:=6.1 include $(INCLUDE_DIR)/target.mk DEFAULT_PACKAGES += \ diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981-rfb-mxl-2p5g-phy-eth1.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981-rfb-mxl-2p5g-phy-eth1.dtso deleted file mode 100644 index 4d0e5c0406..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981-rfb-mxl-2p5g-phy-eth1.dtso +++ /dev/null @@ -1,32 +0,0 @@ -/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */ -/dts-v1/; -/plugin/; - -#include - -/ { - compatible = "mediatek,mt7981-rfb", "mediatek,mt7981"; - - fragment@0 { - target = <&gmac1>; - __overlay__ { - phy-mode = "2500base-x"; - phy-handle = <&phy5>; - }; - }; - - fragment@1 { - target = <&mdio_bus>; - __overlay__ { - reset-gpios = <&pio 14 GPIO_ACTIVE_LOW>; - reset-delay-us = <600>; - reset-post-delay-us = <20000>; - - phy5: ethernet-phy@5 { - reg = <5>; - compatible = "ethernet-phy-ieee802.3-c45"; - phy-mode = "2500base-x"; - }; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981-rfb-mxl-2p5g-phy-swp5.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981-rfb-mxl-2p5g-phy-swp5.dtso deleted file mode 100644 index 710e6c0bcf..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981-rfb-mxl-2p5g-phy-swp5.dtso +++ /dev/null @@ -1,33 +0,0 @@ -/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */ -/dts-v1/; -/plugin/; - -#include - -/ { - compatible = "mediatek,mt7981-rfb", "mediatek,mt7981"; - - fragment@0 { - target = <&sw_p5>; - __overlay__ { - phy-mode = "2500base-x"; - phy-handle = <&phy5>; - status = "okay"; - }; - }; - - fragment@1 { - target = <&mdio_bus>; - __overlay__ { - reset-gpios = <&pio 14 GPIO_ACTIVE_LOW>; - reset-delay-us = <600>; - reset-post-delay-us = <20000>; - - phy5: ethernet-phy@5 { - reg = <5>; - compatible = "ethernet-phy-ieee802.3-c45"; - phy-mode = "2500base-x"; - }; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981-rfb-spim-nand.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981-rfb-spim-nand.dtso deleted file mode 100644 index 5b51dfd671..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981-rfb-spim-nand.dtso +++ /dev/null @@ -1,66 +0,0 @@ -/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */ -/dts-v1/; -/plugin/; - -/ { - compatible = "mediatek,mt7981-rfb", "mediatek,mt7981"; - - fragment@0 { - target = <&spi0>; - __overlay__ { - status = "okay"; - #address-cells = <1>; - #size-cells = <0>; - - spi_nand: spi_nand@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "spi-nand"; - reg = <1>; - spi-max-frequency = <10000000>; - spi-tx-bus-width = <4>; - spi-rx-bus-width = <4>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "BL2"; - reg = <0x00000 0x0100000>; - read-only; - }; - - partition@100000 { - label = "u-boot-env"; - reg = <0x0100000 0x0080000>; - }; - - factory: partition@180000 { - label = "Factory"; - reg = <0x180000 0x0200000>; - }; - - partition@380000 { - label = "FIP"; - reg = <0x380000 0x0200000>; - }; - - partition@580000 { - label = "ubi"; - reg = <0x580000 0x4000000>; - }; - }; - }; - }; - }; - - fragment@1 { - target = <&wifi>; - __overlay__ { - mediatek,mtd-eeprom = <&factory 0x0>; - status = "okay"; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981-rfb.dts b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981-rfb.dts deleted file mode 100644 index b2bb692956..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981-rfb.dts +++ /dev/null @@ -1,188 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2022 MediaTek Inc. - * Author: Sam.Shih - */ - -/dts-v1/; -#include "mt7981.dtsi" - -/ { - model = "MediaTek MT7981 RFB"; - compatible = "mediatek,mt7981-rfb", "mediatek,mt7981"; - - aliases { - serial0 = &uart0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory { - reg = <0 0x40000000 0 0x20000000>; - }; - - reg_3p3v: regulator-3p3v { - compatible = "regulator-fixed"; - regulator-name = "fixed-3.3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; - }; - - reg_5v: regulator-5v { - compatible = "regulator-fixed"; - regulator-name = "fixed-5V"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-boot-on; - regulator-always-on; - }; - - gpio-keys { - compatible = "gpio-keys"; - reset { - label = "reset"; - linux,code = ; - gpios = <&pio 1 GPIO_ACTIVE_LOW>; - }; - wps { - label = "wps"; - linux,code = ; - gpios = <&pio 0 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -ð { - status = "okay"; - - gmac0: mac@0 { - compatible = "mediatek,eth-mac"; - reg = <0>; - phy-mode = "2500base-x"; - - fixed-link { - speed = <2500>; - full-duplex; - pause; - }; - }; - - gmac1: mac@1 { - compatible = "mediatek,eth-mac"; - reg = <1>; - phy-mode = "gmii"; - phy-handle = <&int_gbe_phy>; - }; -}; - -&mdio_bus { - switch: switch@1f { - compatible = "mediatek,mt7531"; - reg = <31>; - interrupt-controller; - #interrupt-cells = <1>; - interrupt-parent = <&pio>; - interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; - reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; - }; -}; - -&crypto { - status = "okay"; -}; - -&pio { - spi0_flash_pins: spi0-pins { - mux { - function = "spi"; - groups = "spi0", "spi0_wp_hold"; - }; - conf-pu { - pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; - drive-strength = ; - bias-pull-up = ; - }; - conf-pd { - pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; - drive-strength = ; - bias-pull-down = ; - }; - }; - -}; - -&spi0 { - pinctrl-names = "default"; - pinctrl-0 = <&spi0_flash_pins>; - cs-gpios = <0>, <0>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; -}; - -&switch { - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - label = "lan1"; - }; - - port@1 { - reg = <1>; - label = "lan2"; - }; - - port@2 { - reg = <2>; - label = "lan3"; - }; - - port@3 { - reg = <3>; - label = "lan4"; - }; - - sw_p5: port@5 { - reg = <5>; - label = "lan5"; - status = "disabled"; - }; - - port@6 { - reg = <6>; - ethernet = <&gmac0>; - phy-mode = "2500base-x"; - - fixed-link { - speed = <2500>; - full-duplex; - pause; - }; - }; - }; -}; - -&xhci { - vusb33-supply = <®_3p3v>; - vbus-supply = <®_5v>; - status = "okay"; -}; - -&uart0 { - status = "okay"; -}; - -&usb_phy { - status = "okay"; -}; - -&watchdog { - status = "okay"; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981.dtsi b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981.dtsi deleted file mode 100644 index cb161df81e..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7981.dtsi +++ /dev/null @@ -1,820 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (c) 2020 MediaTek Inc. - * Author: Sam.Shih - * Author: Jianhui Zhao - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -/ { - compatible = "mediatek,mt7981"; - interrupt-parent = <&gic>; - #address-cells = <2>; - #size-cells = <2>; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - enable-method = "psci"; - reg = <0x0>; - }; - - cpu@1 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - enable-method = "psci"; - reg = <0x1>; - }; - }; - - pwm: pwm@10048000 { - compatible = "mediatek,mt7981-pwm"; - reg = <0 0x10048000 0 0x1000>; - #pwm-cells = <2>; - clocks = <&infracfg CLK_INFRA_PWM_STA>, - <&infracfg CLK_INFRA_PWM_HCK>, - <&infracfg CLK_INFRA_PWM1_CK>, - <&infracfg CLK_INFRA_PWM2_CK>, - <&infracfg CLK_INFRA_PWM3_CK>; - clock-names = "top", "main", "pwm1", "pwm2", "pwm3"; - }; - - fan: pwm-fan { - compatible = "pwm-fan"; - /* cooling level (0, 1, 2, 3, 4, 5, 6, 7) : (0%/25%/37.5%/50%/62.5%/75%/87.5%/100% duty) */ - cooling-levels = <0 63 95 127 159 191 223 255>; - #cooling-cells = <2>; - status = "disabled"; - }; - - thermal-zones { - cpu_thermal: cpu-thermal { - polling-delay-passive = <1000>; - polling-delay = <1000>; - thermal-sensors = <&thermal 0>; - trips { - cpu_trip_active_highest: active-highest { - temperature = <70000>; - hysteresis = <2000>; - type = "active"; - }; - - cpu_trip_active_high: active-high { - temperature = <60000>; - hysteresis = <2000>; - type = "active"; - }; - - cpu_trip_active_med: active-med { - temperature = <50000>; - hysteresis = <2000>; - type = "active"; - }; - - cpu_trip_active_low: active-low { - temperature = <45000>; - hysteresis = <2000>; - type = "active"; - }; - - cpu_trip_active_lowest: active-lowest { - temperature = <40000>; - hysteresis = <2000>; - type = "active"; - }; - }; - - cooling-maps { - cpu-active-highest { - /* active: set fan to cooling level 7 */ - cooling-device = <&fan 7 7>; - trip = <&cpu_trip_active_highest>; - }; - - cpu-active-high { - /* active: set fan to cooling level 5 */ - cooling-device = <&fan 5 5>; - trip = <&cpu_trip_active_high>; - }; - - cpu-active-med { - /* active: set fan to cooling level 3 */ - cooling-device = <&fan 3 3>; - trip = <&cpu_trip_active_med>; - }; - - cpu-active-low { - /* active: set fan to cooling level 2 */ - cooling-device = <&fan 2 2>; - trip = <&cpu_trip_active_low>; - }; - - cpu-active-lowest { - /* active: set fan to cooling level 1 */ - cooling-device = <&fan 1 1>; - trip = <&cpu_trip_active_lowest>; - }; - }; - }; - }; - - thermal: thermal@1100c800 { - #thermal-sensor-cells = <1>; - compatible = "mediatek,mt7981-thermal", "mediatek,mt7986-thermal"; - reg = <0 0x1100c800 0 0x800>; - interrupts = ; - clocks = <&infracfg CLK_INFRA_THERM_CK>, - <&infracfg CLK_INFRA_ADC_26M_CK>; - clock-names = "therm", "auxadc"; - mediatek,auxadc = <&auxadc>; - mediatek,apmixedsys = <&apmixedsys>; - nvmem-cells = <&thermal_calibration>; - nvmem-cell-names = "calibration-data"; - }; - - auxadc: adc@1100d000 { - compatible = "mediatek,mt7981-auxadc", - "mediatek,mt7986-auxadc", - "mediatek,mt7622-auxadc"; - reg = <0 0x1100d000 0 0x1000>; - clocks = <&infracfg CLK_INFRA_ADC_26M_CK>, - <&infracfg CLK_INFRA_ADC_FRC_CK>; - clock-names = "main", "32k"; - #io-channel-cells = <1>; - }; - - wdma: wdma@15104800 { - compatible = "mediatek,wed-wdma"; - reg = <0 0x15104800 0 0x400>, - <0 0x15104c00 0 0x400>; - }; - - ap2woccif: ap2woccif@151a5000 { - compatible = "mediatek,ap2woccif"; - reg = <0 0x151a5000 0 0x1000>, - <0 0x151ad000 0 0x1000>; - interrupt-parent = <&gic>; - interrupts = , - ; - }; - - reserved-memory { - #address-cells = <2>; - #size-cells = <2>; - ranges; - - /* 64 KiB reserved for ramoops/pstore */ - ramoops@42ff0000 { - compatible = "ramoops"; - reg = <0 0x42ff0000 0 0x10000>; - record-size = <0x1000>; - }; - - /* 192 KiB reserved for ARM Trusted Firmware (BL31) */ - secmon_reserved: secmon@43000000 { - reg = <0 0x43000000 0 0x30000>; - no-map; - }; - - wmcpu_emi: wmcpu-reserved@47c80000 { - reg = <0 0x47c80000 0 0x100000>; - no-map; - }; - - wo_emi0: wo-emi@47d80000 { - reg = <0 0x47d80000 0 0x40000>; - no-map; - }; - - wo_data: wo-data@47dc0000 { - reg = <0 0x47dc0000 0 0x240000>; - no-map; - }; - }; - - psci { - compatible = "arm,psci-0.2"; - method = "smc"; - }; - - trng { - compatible = "mediatek,mt7981-rng"; - }; - - clk40m: oscillator@0 { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <40000000>; - clock-output-names = "clkxtal"; - }; - - infracfg: infracfg@10001000 { - compatible = "mediatek,mt7981-infracfg", "syscon"; - reg = <0 0x10001000 0 0x1000>; - #clock-cells = <1>; - }; - - topckgen: topckgen@1001B000 { - compatible = "mediatek,mt7981-topckgen", "syscon"; - reg = <0 0x1001B000 0 0x1000>; - #clock-cells = <1>; - }; - - apmixedsys: apmixedsys@1001E000 { - compatible = "mediatek,mt7981-apmixedsys", "mediatek,mt7986-apmixedsys", "syscon"; - reg = <0 0x1001E000 0 0x1000>; - #clock-cells = <1>; - }; - - timer { - compatible = "arm,armv8-timer"; - interrupt-parent = <&gic>; - clock-frequency = <13000000>; - interrupts = , - , - , - ; - - }; - - watchdog: watchdog@1001c000 { - compatible = "mediatek,mt7986-wdt", - "mediatek,mt6589-wdt"; - reg = <0 0x1001c000 0 0x1000>; - interrupts = ; - #reset-cells = <1>; - status = "disabled"; - }; - - gic: interrupt-controller@c000000 { - compatible = "arm,gic-v3"; - #interrupt-cells = <3>; - interrupt-parent = <&gic>; - interrupt-controller; - reg = <0 0x0c000000 0 0x40000>, /* GICD */ - <0 0x0c080000 0 0x200000>; /* GICR */ - - interrupts = ; - }; - - uart0: serial@11002000 { - compatible = "mediatek,mt6577-uart"; - reg = <0 0x11002000 0 0x400>; - interrupts = ; - clocks = <&infracfg CLK_INFRA_UART0_SEL>, - <&infracfg CLK_INFRA_UART0_CK>; - clock-names = "baud", "bus"; - assigned-clocks = <&topckgen CLK_TOP_UART_SEL>, - <&infracfg CLK_INFRA_UART0_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_CB_CKSQ_40M>, - <&topckgen CLK_TOP_UART_SEL>; - pinctrl-0 = <&uart0_pins>; - pinctrl-names = "default"; - status = "disabled"; - }; - - uart1: serial@11003000 { - compatible = "mediatek,mt6577-uart"; - reg = <0 0x11003000 0 0x400>; - interrupts = ; - clocks = <&infracfg CLK_INFRA_UART1_SEL>, - <&infracfg CLK_INFRA_UART1_CK>; - clock-names = "baud", "bus"; - assigned-clocks = <&topckgen CLK_TOP_UART_SEL>, - <&infracfg CLK_INFRA_UART1_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_CB_CKSQ_40M>, - <&topckgen CLK_TOP_UART_SEL>; - status = "disabled"; - }; - - uart2: serial@11004000 { - compatible = "mediatek,mt6577-uart"; - reg = <0 0x11004000 0 0x400>; - interrupts = ; - clocks = <&infracfg CLK_INFRA_UART2_SEL>, - <&infracfg CLK_INFRA_UART2_CK>; - clock-names = "baud", "bus"; - assigned-clocks = <&topckgen CLK_TOP_UART_SEL>, - <&infracfg CLK_INFRA_UART2_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_CB_CKSQ_40M>, - <&topckgen CLK_TOP_UART_SEL>; - status = "disabled"; - }; - - i2c0: i2c@11007000 { - compatible = "mediatek,mt7981-i2c"; - reg = <0 0x11007000 0 0x1000>, - <0 0x10217080 0 0x80>; - interrupts = ; - clock-div = <1>; - clocks = <&infracfg CLK_INFRA_I2C0_CK>, - <&infracfg CLK_INFRA_AP_DMA_CK>, - <&infracfg CLK_INFRA_I2C_MCK_CK>, - <&infracfg CLK_INFRA_I2C_PCK_CK>; - clock-names = "main", "dma", "arb", "pmic"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - pcie: pcie@11280000 { - compatible = "mediatek,mt7981-pcie", - "mediatek,mt7986-pcie"; - device_type = "pci"; - reg = <0 0x11280000 0 0x4000>; - reg-names = "pcie-mac"; - #address-cells = <3>; - #size-cells = <2>; - interrupts = ; - bus-range = <0x00 0xff>; - ranges = <0x82000000 0 0x20000000 - 0x0 0x20000000 0 0x10000000>; - status = "disabled"; - - clocks = <&infracfg CLK_INFRA_IPCIE_CK>, - <&infracfg CLK_INFRA_IPCIE_PIPE_CK>, - <&infracfg CLK_INFRA_IPCIER_CK>, - <&infracfg CLK_INFRA_IPCIEB_CK>; - - phys = <&u3port0 PHY_TYPE_PCIE>; - phy-names = "pcie-phy"; - - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 7>; - interrupt-map = <0 0 0 1 &pcie_intc 0>, - <0 0 0 2 &pcie_intc 1>, - <0 0 0 3 &pcie_intc 2>, - <0 0 0 4 &pcie_intc 3>; - pcie_intc: interrupt-controller { - interrupt-controller; - #address-cells = <0>; - #interrupt-cells = <1>; - }; - }; - - crypto: crypto@10320000 { - compatible = "inside-secure,safexcel-eip97"; - reg = <0 0x10320000 0 0x40000>; - interrupts = , - , - , - ; - interrupt-names = "ring0", "ring1", "ring2", "ring3"; - clocks = <&topckgen CLK_TOP_EIP97B>; - clock-names = "top_eip97_ck"; - assigned-clocks = <&topckgen CLK_TOP_EIP97B_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_CB_NET1_D5>; - }; - - pio: pinctrl@11d00000 { - compatible = "mediatek,mt7981-pinctrl"; - reg = <0 0x11d00000 0 0x1000>, - <0 0x11c00000 0 0x1000>, - <0 0x11c10000 0 0x1000>, - <0 0x11d20000 0 0x1000>, - <0 0x11e00000 0 0x1000>, - <0 0x11e20000 0 0x1000>, - <0 0x11f00000 0 0x1000>, - <0 0x11f10000 0 0x1000>, - <0 0x1000b000 0 0x1000>; - reg-names = "gpio", "iocfg_rt", "iocfg_rm", - "iocfg_rb", "iocfg_lb", "iocfg_bl", - "iocfg_tm", "iocfg_tl", "eint"; - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pio 0 0 56>; - interrupt-controller; - interrupts = ; - interrupt-parent = <&gic>; - #interrupt-cells = <2>; - - mdio_pins: mdc-mdio-pins { - mux { - function = "eth"; - groups = "smi_mdc_mdio"; - }; - }; - - uart0_pins: uart0-pins { - mux { - function = "uart"; - groups = "uart0"; - }; - }; - - wifi_dbdc_pins: wifi-dbdc-pins { - mux { - function = "eth"; - groups = "wf0_mode1"; - }; - conf { - pins = "WF_HB1", "WF_HB2", "WF_HB3", "WF_HB4", - "WF_HB0", "WF_HB0_B", "WF_HB5", "WF_HB6", - "WF_HB7", "WF_HB8", "WF_HB9", "WF_HB10", - "WF_TOP_CLK", "WF_TOP_DATA", "WF_XO_REQ", - "WF_CBA_RESETB", "WF_DIG_RESETB"; - drive-strength = <4>; - }; - }; - - gbe_led0_pins: gbe-led0-pins { - mux { - function = "led"; - groups = "gbe_led0"; - }; - }; - - gbe_led1_pins: gbe-led1-pins { - mux { - function = "led"; - groups = "gbe_led1"; - }; - }; - }; - - ethsys: syscon@15000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "mediatek,mt7981-ethsys", - "mediatek,mt7986-ethsys", - "syscon"; - reg = <0 0x15000000 0 0x1000>; - #clock-cells = <1>; - #reset-cells = <1>; - }; - - wed: wed@15010000 { - compatible = "mediatek,mt7981-wed", - "mediatek,mt7986-wed", - "syscon"; - reg = <0 0x15010000 0 0x1000>; - interrupt-parent = <&gic>; - interrupts = ; - memory-region = <&wo_emi0>, <&wo_data>; - memory-region-names = "wo-emi", "wo-data"; - mediatek,wo-ccif = <&wo_ccif0>; - mediatek,wo-ilm = <&wo_ilm0>; - mediatek,wo-dlm = <&wo_dlm0>; - mediatek,wo-cpuboot = <&wo_cpuboot>; - }; - - eth: ethernet@15100000 { - compatible = "mediatek,mt7981-eth"; - reg = <0 0x15100000 0 0x80000>; - interrupts = , - , - , - ; - clocks = <ðsys CLK_ETH_FE_EN>, - <ðsys CLK_ETH_GP2_EN>, - <ðsys CLK_ETH_GP1_EN>, - <ðsys CLK_ETH_WOCPU0_EN>, - <&sgmiisys0 CLK_SGM0_TX_EN>, - <&sgmiisys0 CLK_SGM0_RX_EN>, - <&sgmiisys0 CLK_SGM0_CK0_EN>, - <&sgmiisys0 CLK_SGM0_CDR_CK0_EN>, - <&sgmiisys1 CLK_SGM1_TX_EN>, - <&sgmiisys1 CLK_SGM1_RX_EN>, - <&sgmiisys1 CLK_SGM1_CK1_EN>, - <&sgmiisys1 CLK_SGM1_CDR_CK1_EN>, - <&topckgen CLK_TOP_SGM_REG>, - <&topckgen CLK_TOP_NETSYS_SEL>, - <&topckgen CLK_TOP_NETSYS_500M_SEL>; - clock-names = "fe", "gp2", "gp1", "wocpu0", - "sgmii_tx250m", "sgmii_rx250m", - "sgmii_cdr_ref", "sgmii_cdr_fb", - "sgmii2_tx250m", "sgmii2_rx250m", - "sgmii2_cdr_ref", "sgmii2_cdr_fb", - "sgmii_ck", "netsys0", "netsys1"; - assigned-clocks = <&topckgen CLK_TOP_NETSYS_2X_SEL>, - <&topckgen CLK_TOP_SGM_325M_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_CB_NET2_800M>, - <&topckgen CLK_TOP_CB_SGM_325M>; - mediatek,ethsys = <ðsys>; - mediatek,sgmiisys = <&sgmiisys0>, <&sgmiisys1>; - mediatek,infracfg = <&topmisc>; - mediatek,wed = <&wed>; - #reset-cells = <1>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - mdio_bus: mdio-bus { - #address-cells = <1>; - #size-cells = <0>; - - int_gbe_phy: ethernet-phy@0 { - reg = <0>; - compatible = "ethernet-phy-ieee802.3-c22"; - phy-mode = "gmii"; - phy-is-integrated; - nvmem-cells = <&phy_calibration>; - nvmem-cell-names = "phy-cal-data"; - - leds { - #address-cells = <1>; - #size-cells = <0>; - - int_gbe_phy_led0: int-gbe-phy-led0@0 { - reg = <0>; - function = LED_FUNCTION_LAN; - status = "disabled"; - }; - - int_gbe_phy_led1: int-gbe-phy-led1@1 { - reg = <1>; - function = LED_FUNCTION_LAN; - status = "disabled"; - }; - }; - }; - }; - }; - - wo_dlm0: syscon@151e8000 { - compatible = "mediatek,mt7986-wo-dlm", "syscon"; - reg = <0 0x151e8000 0 0x2000>; - }; - - wo_ilm0: syscon@151e0000 { - compatible = "mediatek,mt7986-wo-ilm", "syscon"; - reg = <0 0x151e0000 0 0x8000>; - }; - - wo_cpuboot: syscon@15194000 { - compatible = "mediatek,mt7986-wo-cpuboot", "syscon"; - reg = <0 0x15194000 0 0x1000>; - }; - - wo_ccif0: syscon@151a5000 { - compatible = "mediatek,mt7986-wo-ccif", "syscon"; - reg = <0 0x151a5000 0 0x1000>; - interrupt-parent = <&gic>; - interrupts = ; - }; - - sgmiisys0: syscon@10060000 { - compatible = "mediatek,mt7981-sgmiisys_0", "mediatek,mt7986-sgmiisys_0", "syscon"; - reg = <0 0x10060000 0 0x1000>; - mediatek,pnswap; - #clock-cells = <1>; - }; - - sgmiisys1: syscon@10070000 { - compatible = "mediatek,mt7981-sgmiisys_1", "mediatek,mt7986-sgmiisys_1", "syscon"; - reg = <0 0x10070000 0 0x1000>; - #clock-cells = <1>; - }; - - topmisc: topmisc@11d10000 { - compatible = "mediatek,mt7981-topmisc", "syscon"; - reg = <0 0x11d10000 0 0x10000>; - #clock-cells = <1>; - }; - - snand: snfi@11005000 { - compatible = "mediatek,mt7986-snand"; - reg = <0 0x11005000 0 0x1000>, <0 0x11006000 0 0x1000>; - reg-names = "nfi", "ecc"; - interrupts = ; - clocks = <&infracfg CLK_INFRA_SPINFI1_CK>, - <&infracfg CLK_INFRA_NFI1_CK>, - <&infracfg CLK_INFRA_NFI_HCK_CK>; - clock-names = "pad_clk", "nfi_clk", "nfi_hclk"; - assigned-clocks = <&topckgen CLK_TOP_SPINFI_SEL>, - <&topckgen CLK_TOP_NFI1X_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_CB_M_D8>, - <&topckgen CLK_TOP_CB_M_D8>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - mmc0: mmc@11230000 { - compatible = "mediatek,mt7986-mmc", - "mediatek,mt7981-mmc"; - reg = <0 0x11230000 0 0x1000>, <0 0x11c20000 0 0x1000>; - interrupts = ; - clocks = <&infracfg CLK_INFRA_MSDC_CK>, - <&infracfg CLK_INFRA_MSDC_HCK_CK>, - <&infracfg CLK_INFRA_MSDC_66M_CK>, - <&infracfg CLK_INFRA_MSDC_133M_CK>; - assigned-clocks = <&topckgen CLK_TOP_EMMC_208M_SEL>, - <&topckgen CLK_TOP_EMMC_400M_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_CB_M_D2>, - <&topckgen CLK_TOP_CB_NET2_D2>; - clock-names = "source", "hclk", "axi_cg", "ahb_cg"; - status = "disabled"; - }; - - wed_pcie: wed_pcie@10003000 { - compatible = "mediatek,wed_pcie"; - reg = <0 0x10003000 0 0x10>; - }; - - spi0: spi@1100a000 { - compatible = "mediatek,mt7986-spi-ipm", "mediatek,spi-ipm"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0 0x1100a000 0 0x100>; - interrupts = ; - clocks = <&topckgen CLK_TOP_CB_M_D2>, - <&topckgen CLK_TOP_SPI_SEL>, - <&infracfg CLK_INFRA_SPI0_CK>, - <&infracfg CLK_INFRA_SPI0_HCK_CK>; - - clock-names = "parent-clk", "sel-clk", "spi-clk", "hclk"; - status = "disabled"; - }; - - spi1: spi@1100b000 { - compatible = "mediatek,mt7986-spi-ipm", "mediatek,spi-ipm"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0 0x1100b000 0 0x100>; - interrupts = ; - clocks = <&topckgen CLK_TOP_CB_M_D2>, - <&topckgen CLK_TOP_SPIM_MST_SEL>, - <&infracfg CLK_INFRA_SPI1_CK>, - <&infracfg CLK_INFRA_SPI1_HCK_CK>; - clock-names = "parent-clk", "sel-clk", "spi-clk", "hclk"; - status = "disabled"; - }; - - spi2: spi@11009000 { - compatible = "mediatek,mt7986-spi-ipm", "mediatek,spi-ipm"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0 0x11009000 0 0x100>; - interrupts = ; - clocks = <&topckgen CLK_TOP_CB_M_D2>, - <&topckgen CLK_TOP_SPI_SEL>, - <&infracfg CLK_INFRA_SPI2_CK>, - <&infracfg CLK_INFRA_SPI2_HCK_CK>; - clock-names = "parent-clk", "sel-clk", "spi-clk", "hclk"; - status = "disabled"; - }; - - consys: consys@10000000 { - compatible = "mediatek,mt7981-consys"; - reg = <0 0x10000000 0 0x8600000>; - memory-region = <&wmcpu_emi>; - }; - - xhci: usb@11200000 { - compatible = "mediatek,mt7986-xhci", - "mediatek,mtk-xhci"; - reg = <0 0x11200000 0 0x2e00>, - <0 0x11203e00 0 0x0100>; - reg-names = "mac", "ippc"; - interrupts = ; - clocks = <&infracfg CLK_INFRA_IUSB_SYS_CK>, - <&infracfg CLK_INFRA_IUSB_CK>, - <&infracfg CLK_INFRA_IUSB_133_CK>, - <&infracfg CLK_INFRA_IUSB_66M_CK>, - <&topckgen CLK_TOP_U2U3_XHCI_SEL>; - clock-names = "sys_ck", - "ref_ck", - "mcu_ck", - "dma_ck", - "xhci_ck"; - phys = <&u2port0 PHY_TYPE_USB2>, - <&u3port0 PHY_TYPE_USB3>; - vusb33-supply = <®_3p3v>; - status = "disabled"; - }; - - usb_phy: usb-phy@11e10000 { - compatible = "mediatek,mt7981", - "mediatek,generic-tphy-v2"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0 0x11e10000 0x1700>; - status = "disabled"; - - u2port0: usb-phy@0 { - reg = <0x0 0x700>; - clocks = <&topckgen CLK_TOP_USB_FRMCNT_SEL>; - clock-names = "ref"; - #phy-cells = <1>; - }; - - u3port0: usb-phy@700 { - reg = <0x700 0x900>; - clocks = <&topckgen CLK_TOP_USB3_PHY_SEL>; - clock-names = "ref"; - #phy-cells = <1>; - mediatek,syscon-type = <&topmisc 0x218 0>; - status = "okay"; - }; - }; - - reg_3p3v: regulator-3p3v { - compatible = "regulator-fixed"; - regulator-name = "fixed-3.3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; - }; - - efuse: efuse@11f20000 { - compatible = "mediatek,mt7981-efuse", - "mediatek,efuse"; - reg = <0 0x11f20000 0 0x1000>; - #address-cells = <1>; - #size-cells = <1>; - status = "okay"; - - thermal_calibration: thermal-calib@274 { - reg = <0x274 0xc>; - }; - - phy_calibration: phy-calib@8dc { - reg = <0x8dc 0x10>; - }; - - comb_rx_imp_p0: usb3-rx-imp@8c8 { - reg = <0x8c8 1>; - bits = <0 5>; - }; - - comb_tx_imp_p0: usb3-tx-imp@8c8 { - reg = <0x8c8 2>; - bits = <5 5>; - }; - - comb_intr_p0: usb3-intr@8c9 { - reg = <0x8c9 1>; - bits = <2 6>; - }; - }; - - afe: audio-controller@11210000 { - compatible = "mediatek,mt79xx-audio"; - reg = <0 0x11210000 0 0x9000>; - interrupts = ; - clocks = <&infracfg CLK_INFRA_AUD_BUS_CK>, - <&infracfg CLK_INFRA_AUD_26M_CK>, - <&infracfg CLK_INFRA_AUD_L_CK>, - <&infracfg CLK_INFRA_AUD_AUD_CK>, - <&infracfg CLK_INFRA_AUD_EG2_CK>, - <&topckgen CLK_TOP_AUD_SEL>; - clock-names = "aud_bus_ck", - "aud_26m_ck", - "aud_l_ck", - "aud_aud_ck", - "aud_eg2_ck", - "aud_sel"; - assigned-clocks = <&topckgen CLK_TOP_AUD_SEL>, - <&topckgen CLK_TOP_A1SYS_SEL>, - <&topckgen CLK_TOP_AUD_L_SEL>, - <&topckgen CLK_TOP_A_TUNER_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_CB_APLL2_196M>, - <&topckgen CLK_TOP_APLL2_D4>, - <&topckgen CLK_TOP_CB_APLL2_196M>, - <&topckgen CLK_TOP_APLL2_D4>; - status = "disabled"; - }; - - ice: ice_debug { - compatible = "mediatek,mt7981-ice_debug", - "mediatek,mt2701-ice_debug"; - clocks = <&infracfg CLK_INFRA_DBG_CK>; - clock-names = "ice_dbg"; - }; - - wifi: wifi@18000000 { - compatible = "mediatek,mt7981-wmac"; - resets = <&watchdog MT7986_TOPRGU_CONSYS_SW_RST>; - reset-names = "consys"; - pinctrl-0 = <&wifi_dbdc_pins>; - pinctrl-names = "dbdc"; - clocks = <&topckgen CLK_TOP_NETSYS_MCU_SEL>, - <&topckgen CLK_TOP_AP2CNN_HOST_SEL>; - clock-names = "mcu", "ap2conn"; - reg = <0 0x18000000 0 0x1000000>, - <0 0x10003000 0 0x1000>, - <0 0x11d10000 0 0x1000>; - interrupts = , - , - , - ; - memory-region = <&wmcpu_emi>; - status = "disabled"; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso deleted file mode 100644 index 779dc6782b..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dtso +++ /dev/null @@ -1,29 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2021 MediaTek Inc. - * Author: Sam.Shih - */ - -/dts-v1/; -/plugin/; - -/ { - compatible = "bananapi,bpi-r3", "mediatek,mt7986a"; - - fragment@0 { - target-path = "/soc/mmc@11230000"; - __overlay__ { - bus-width = <8>; - max-frequency = <200000000>; - cap-mmc-highspeed; - mmc-hs200-1_8v; - mmc-hs400-1_8v; - hs400-ds-delay = <0x14014>; - non-removable; - no-sd; - no-sdio; - status = "okay"; - }; - }; -}; - diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso deleted file mode 100644 index 0846d88f62..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dtso +++ /dev/null @@ -1,55 +0,0 @@ -/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */ -/* - * Authors: Daniel Golle - * Frank Wunderlich - */ - -/dts-v1/; -/plugin/; - -/ { - compatible = "bananapi,bpi-r3", "mediatek,mt7986a"; - - fragment@0 { - target-path = "/soc/spi@1100a000"; - __overlay__ { - #address-cells = <1>; - #size-cells = <0>; - spi_nand: spi_nand@0 { - compatible = "spi-nand"; - reg = <0>; - spi-max-frequency = <10000000>; - spi-tx-bus-width = <4>; - spi-rx-bus-width = <4>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "bl2"; - reg = <0x0 0x80000>; - read-only; - }; - - partition@80000 { - label = "reserved"; - reg = <0x80000 0x300000>; - }; - - partition@380000 { - label = "fip"; - reg = <0x380000 0x200000>; - read-only; - }; - - partition@580000 { - label = "ubi"; - reg = <0x580000 0x7a80000>; - }; - }; - }; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso deleted file mode 100644 index e48881be4e..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso +++ /dev/null @@ -1,63 +0,0 @@ -/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */ -/* - * Authors: Daniel Golle - * Frank Wunderlich - */ - -/dts-v1/; -/plugin/; - -/ { - compatible = "bananapi,bpi-r3", "mediatek,mt7986a"; - - fragment@0 { - target-path = "/soc/spi@1100a000"; - __overlay__ { - #address-cells = <1>; - #size-cells = <0>; - flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <10000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "bl2"; - reg = <0x0 0x40000>; - read-only; - }; - - partition@40000 { - label = "u-boot-env"; - reg = <0x40000 0x40000>; - }; - - partition@80000 { - label = "reserved2"; - reg = <0x80000 0x80000>; - }; - - partition@100000 { - label = "fip"; - reg = <0x100000 0x80000>; - read-only; - }; - - partition@180000 { - label = "recovery"; - reg = <0x180000 0xa80000>; - }; - - partition@c00000 { - label = "fit"; - reg = <0xc00000 0x1400000>; - }; - }; - }; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso deleted file mode 100644 index f623bce075..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dtso +++ /dev/null @@ -1,23 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2021 MediaTek Inc. - * Author: Sam.Shih - */ - -/dts-v1/; -/plugin/; - -/ { - compatible = "bananapi,bpi-r3", "mediatek,mt7986a"; - - fragment@0 { - target-path = "/soc/mmc@11230000"; - __overlay__ { - bus-width = <4>; - max-frequency = <52000000>; - cap-sd-highspeed; - status = "okay"; - }; - }; -}; - diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts deleted file mode 100644 index d326c416a9..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts +++ /dev/null @@ -1,501 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2021 MediaTek Inc. - * Authors: Sam.Shih - * Frank Wunderlich - * Daniel Golle - */ - -/dts-v1/; -#include -#include -#include -#include - -#include "mt7986a.dtsi" - -/ { - model = "Bananapi BPI-R3"; - chassis-type = "embedded"; - compatible = "bananapi,bpi-r3", "mediatek,mt7986a"; - - aliases { - serial0 = &uart0; - ethernet0 = &gmac0; - ethernet1 = &gmac1; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - dcin: regulator-12vd { - compatible = "regulator-fixed"; - regulator-name = "12vd"; - regulator-min-microvolt = <12000000>; - regulator-max-microvolt = <12000000>; - regulator-boot-on; - regulator-always-on; - }; - - fan: pwm-fan { - compatible = "pwm-fan"; - #cooling-cells = <2>; - /* cooling level (0, 1, 2) - pwm inverted */ - cooling-levels = <255 96 0>; - pwms = <&pwm 0 10000 0>; - status = "okay"; - }; - - gpio-keys { - compatible = "gpio-keys"; - - reset-key { - label = "reset"; - linux,code = ; - gpios = <&pio 9 GPIO_ACTIVE_LOW>; - }; - - wps-key { - label = "wps"; - linux,code = ; - gpios = <&pio 10 GPIO_ACTIVE_LOW>; - }; - }; - - /* i2c of the left SFP cage (wan) */ - i2c_sfp1: i2c-gpio-0 { - compatible = "i2c-gpio"; - sda-gpios = <&pio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - scl-gpios = <&pio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - i2c-gpio,delay-us = <2>; - #address-cells = <1>; - #size-cells = <0>; - }; - - /* i2c of the right SFP cage (lan) */ - i2c_sfp2: i2c-gpio-1 { - compatible = "i2c-gpio"; - sda-gpios = <&pio 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - scl-gpios = <&pio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - i2c-gpio,delay-us = <2>; - #address-cells = <1>; - #size-cells = <0>; - }; - - leds { - compatible = "gpio-leds"; - - green_led: led-0 { - color = ; - function = LED_FUNCTION_POWER; - gpios = <&pio 69 GPIO_ACTIVE_HIGH>; - default-state = "on"; - }; - - blue_led: led-1 { - color = ; - function = LED_FUNCTION_STATUS; - gpios = <&pio 86 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - }; - - reg_1p8v: regulator-1p8v { - compatible = "regulator-fixed"; - regulator-name = "1.8vd"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-boot-on; - regulator-always-on; - vin-supply = <&dcin>; - }; - - reg_3p3v: regulator-3p3v { - compatible = "regulator-fixed"; - regulator-name = "3.3vd"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; - vin-supply = <&dcin>; - }; - - /* left SFP cage (wan) */ - sfp1: sfp-1 { - compatible = "sff,sfp"; - i2c-bus = <&i2c_sfp1>; - los-gpios = <&pio 46 GPIO_ACTIVE_HIGH>; - mod-def0-gpios = <&pio 49 GPIO_ACTIVE_LOW>; - tx-disable-gpios = <&pio 20 GPIO_ACTIVE_HIGH>; - tx-fault-gpios = <&pio 7 GPIO_ACTIVE_HIGH>; - maximum-power-milliwatt = <3000>; - }; - - /* right SFP cage (lan) */ - sfp2: sfp-2 { - compatible = "sff,sfp"; - i2c-bus = <&i2c_sfp2>; - los-gpios = <&pio 31 GPIO_ACTIVE_HIGH>; - mod-def0-gpios = <&pio 47 GPIO_ACTIVE_LOW>; - tx-disable-gpios = <&pio 15 GPIO_ACTIVE_HIGH>; - tx-fault-gpios = <&pio 48 GPIO_ACTIVE_HIGH>; - maximum-power-milliwatt = <3000>; - }; -}; - -&cpu_thermal { - cooling-maps { - cpu-active-high { - /* active: set fan to cooling level 2 */ - cooling-device = <&fan 2 2>; - trip = <&cpu_trip_active_high>; - }; - - cpu-active-med { - /* active: set fan to cooling level 1 */ - cooling-device = <&fan 1 1>; - trip = <&cpu_trip_active_med>; - }; - - cpu-active-low { - /* active: set fan to cooling level 0 */ - cooling-device = <&fan 0 0>; - trip = <&cpu_trip_active_low>; - }; - }; -}; - -&crypto { - status = "okay"; -}; - -ð { - status = "okay"; - - gmac0: mac@0 { - compatible = "mediatek,eth-mac"; - reg = <0>; - phy-mode = "2500base-x"; - - fixed-link { - speed = <2500>; - full-duplex; - pause; - }; - }; - - gmac1: mac@1 { - compatible = "mediatek,eth-mac"; - reg = <1>; - phy-mode = "2500base-x"; - sfp = <&sfp1>; - managed = "in-band-status"; - }; - - mdio: mdio-bus { - #address-cells = <1>; - #size-cells = <0>; - }; -}; - -&mdio { - switch: switch@1f { - compatible = "mediatek,mt7531"; - reg = <31>; - interrupt-controller; - #interrupt-cells = <1>; - interrupt-parent = <&pio>; - interrupts = <66 IRQ_TYPE_LEVEL_HIGH>; - reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; - }; -}; - -&mmc0 { - pinctrl-names = "default", "state_uhs"; - pinctrl-0 = <&mmc0_pins_default>; - pinctrl-1 = <&mmc0_pins_uhs>; - vmmc-supply = <®_3p3v>; - vqmmc-supply = <®_1p8v>; -}; - -&i2c0 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c_pins>; - status = "okay"; -}; - -&pcie { - pinctrl-names = "default"; - pinctrl-0 = <&pcie_pins>; - status = "okay"; -}; - -&pcie_phy { - status = "okay"; -}; - -&pio { - i2c_pins: i2c-pins { - mux { - function = "i2c"; - groups = "i2c"; - }; - }; - - mmc0_pins_default: mmc0-pins { - mux { - function = "emmc"; - groups = "emmc_51"; - }; - conf-cmd-dat { - pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", - "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", - "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; - input-enable; - drive-strength = <4>; - bias-pull-up = ; /* pull-up 10K */ - }; - conf-clk { - pins = "EMMC_CK"; - drive-strength = <6>; - bias-pull-down = ; /* pull-down 50K */ - }; - conf-ds { - pins = "EMMC_DSL"; - bias-pull-down = ; /* pull-down 50K */ - }; - conf-rst { - pins = "EMMC_RSTB"; - drive-strength = <4>; - bias-pull-up = ; /* pull-up 10K */ - }; - }; - - mmc0_pins_uhs: mmc0-uhs-pins { - mux { - function = "emmc"; - groups = "emmc_51"; - }; - conf-cmd-dat { - pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", - "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", - "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; - input-enable; - drive-strength = <4>; - bias-pull-up = ; /* pull-up 10K */ - }; - conf-clk { - pins = "EMMC_CK"; - drive-strength = <6>; - bias-pull-down = ; /* pull-down 50K */ - }; - conf-ds { - pins = "EMMC_DSL"; - bias-pull-down = ; /* pull-down 50K */ - }; - conf-rst { - pins = "EMMC_RSTB"; - drive-strength = <4>; - bias-pull-up = ; /* pull-up 10K */ - }; - }; - - pcie_pins: pcie-pins { - mux { - function = "pcie"; - groups = "pcie_clk", "pcie_pereset"; - }; - }; - - pwm_pins: pwm-pins { - mux { - function = "pwm"; - groups = "pwm0", "pwm1_0"; - }; - }; - - spi_flash_pins: spi-flash-pins { - mux { - function = "spi"; - groups = "spi0", "spi0_wp_hold"; - }; - }; - - spic_pins: spic-pins { - mux { - function = "spi"; - groups = "spi1_0"; - }; - }; - - uart1_pins: uart1-pins { - mux { - function = "uart"; - groups = "uart1_rx_tx"; - }; - }; - - uart2_pins: uart2-pins { - mux { - function = "uart"; - groups = "uart2_0_rx_tx"; - }; - }; - - wf_2g_5g_pins: wf-2g-5g-pins { - mux { - function = "wifi"; - groups = "wf_2g", "wf_5g"; - }; - conf { - pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", - "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", - "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", - "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", - "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", - "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", - "WF1_TOP_CLK", "WF1_TOP_DATA"; - drive-strength = <4>; - }; - }; - - wf_dbdc_pins: wf-dbdc-pins { - mux { - function = "wifi"; - groups = "wf_dbdc"; - }; - conf { - pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", - "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", - "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", - "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", - "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", - "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", - "WF1_TOP_CLK", "WF1_TOP_DATA"; - drive-strength = <4>; - }; - }; - - wf_led_pins: wf-led-pins { - mux { - function = "led"; - groups = "wifi_led"; - }; - }; -}; - -&pwm { - pinctrl-names = "default"; - pinctrl-0 = <&pwm_pins>; - status = "okay"; -}; - -&spi0 { - pinctrl-names = "default"; - pinctrl-0 = <&spi_flash_pins>; - status = "okay"; -}; - -&spi1 { - pinctrl-names = "default"; - pinctrl-0 = <&spic_pins>; - status = "okay"; -}; - -&ssusb { - status = "okay"; -}; - -&switch { - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - label = "wan"; - }; - - port@1 { - reg = <1>; - label = "lan0"; - }; - - port@2 { - reg = <2>; - label = "lan1"; - }; - - port@3 { - reg = <3>; - label = "lan2"; - }; - - port@4 { - reg = <4>; - label = "lan3"; - }; - - port5: port@5 { - reg = <5>; - label = "lan4"; - phy-mode = "2500base-x"; - sfp = <&sfp2>; - managed = "in-band-status"; - }; - - port@6 { - reg = <6>; - label = "cpu"; - ethernet = <&gmac0>; - phy-mode = "2500base-x"; - - fixed-link { - speed = <2500>; - full-duplex; - pause; - }; - }; - }; -}; - -&trng { - status = "okay"; -}; - -&uart0 { - status = "okay"; -}; - -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_pins>; - status = "okay"; -}; - -&uart2 { - pinctrl-names = "default"; - pinctrl-0 = <&uart2_pins>; - status = "okay"; -}; - -&usb_phy { - status = "okay"; -}; - -&watchdog { - status = "okay"; -}; - -&wifi { - status = "okay"; - pinctrl-names = "default", "dbdc"; - pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>; - pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>; - - led { - led-active-low; - }; -}; - diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-rfb-spim-nand.dts b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-rfb-spim-nand.dts deleted file mode 100644 index ce007099d2..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-rfb-spim-nand.dts +++ /dev/null @@ -1,52 +0,0 @@ -/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */ - -#include "mt7986a-rfb.dtsi" - -/ { - compatible = "mediatek,mt7986a-rfb-snand"; -}; - -&spi0 { - status = "okay"; - - spi_nand: spi_nand@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "spi-nand"; - reg = <1>; - spi-max-frequency = <10000000>; - spi-tx-bus-width = <4>; - spi-rx-bus-width = <4>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - partition@0 { - label = "BL2"; - reg = <0x00000 0x0100000>; - read-only; - }; - partition@100000 { - label = "u-boot-env"; - reg = <0x0100000 0x0080000>; - }; - factory: partition@180000 { - label = "Factory"; - reg = <0x180000 0x0200000>; - }; - partition@380000 { - label = "FIP"; - reg = <0x380000 0x0200000>; - }; - partition@580000 { - label = "ubi"; - reg = <0x580000 0x4000000>; - }; - }; - }; -}; - -&wifi { - mediatek,mtd-eeprom = <&factory 0>; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-rfb-spim-nor.dts b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-rfb-spim-nor.dts deleted file mode 100644 index ea148315f0..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-rfb-spim-nor.dts +++ /dev/null @@ -1,51 +0,0 @@ -/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */ - -#include "mt7986a-rfb.dtsi" - -/ { - compatible = "mediatek,mt7986a-rfb-snor"; -}; - -&spi0 { - status = "okay"; - - spi_nor: spi_nor@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <52000000>; - spi-tx-bus-width = <4>; - spi-rx-bus-width = <4>; - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@00000 { - label = "BL2"; - reg = <0x00000 0x0040000>; - }; - partition@40000 { - label = "u-boot-env"; - reg = <0x40000 0x0010000>; - }; - factory: partition@50000 { - label = "Factory"; - reg = <0x50000 0x00B0000>; - }; - partition@100000 { - label = "FIP"; - reg = <0x100000 0x0080000>; - }; - partition@180000 { - label = "firmware"; - reg = <0x180000 0xE00000>; - }; - }; - }; -}; - -&wifi { - mediatek,mtd-eeprom = <&factory 0>; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dtsi b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dtsi deleted file mode 100644 index 26d560bd4b..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dtsi +++ /dev/null @@ -1,389 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2021 MediaTek Inc. - * Author: Sam.Shih - */ - -/dts-v1/; -#include "mt7986a.dtsi" - -/ { - model = "MediaTek MT7986a RFB"; - compatible = "mediatek,mt7986a-rfb"; - - aliases { - serial0 = &uart0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory { - reg = <0 0x40000000 0 0x40000000>; - }; - - reg_1p8v: regulator-1p8v { - compatible = "regulator-fixed"; - regulator-name = "fixed-1.8V"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-boot-on; - regulator-always-on; - }; - - reg_3p3v: regulator-3p3v { - compatible = "regulator-fixed"; - regulator-name = "fixed-3.3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; - }; - - reg_5v: regulator-5v { - compatible = "regulator-fixed"; - regulator-name = "fixed-5V"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-boot-on; - regulator-always-on; - }; -}; - -ð { - status = "okay"; - - gmac0: mac@0 { - compatible = "mediatek,eth-mac"; - reg = <0>; - phy-mode = "2500base-x"; - - fixed-link { - speed = <2500>; - full-duplex; - pause; - }; - }; - - gmac1: mac@1 { - compatible = "mediatek,eth-mac"; - reg = <1>; - phy-mode = "2500base-x"; - }; - - mdio: mdio-bus { - #address-cells = <1>; - #size-cells = <0>; - }; -}; - -&wifi { - status = "okay"; - pinctrl-names = "default", "dbdc"; - pinctrl-0 = <&wf_2g_5g_pins>; - pinctrl-1 = <&wf_dbdc_pins>; -}; - -&mdio { - phy5: phy@5 { - compatible = "ethernet-phy-id67c9.de0a"; - reg = <5>; - - reset-gpios = <&pio 6 1>; - reset-deassert-us = <20000>; - }; - - phy6: phy@6 { - compatible = "ethernet-phy-id67c9.de0a"; - reg = <6>; - }; - - switch: switch@1f { - compatible = "mediatek,mt7531"; - reg = <31>; - reset-gpios = <&pio 5 0>; - }; -}; - -&crypto { - status = "okay"; -}; - -&mmc0 { - pinctrl-names = "default", "state_uhs"; - pinctrl-0 = <&mmc0_pins_default>; - pinctrl-1 = <&mmc0_pins_uhs>; - bus-width = <8>; - max-frequency = <200000000>; - cap-mmc-highspeed; - mmc-hs200-1_8v; - mmc-hs400-1_8v; - hs400-ds-delay = <0x14014>; - vmmc-supply = <®_3p3v>; - vqmmc-supply = <®_1p8v>; - non-removable; - no-sd; - no-sdio; - status = "okay"; -}; - -&pcie { - pinctrl-names = "default"; - pinctrl-0 = <&pcie_pins>; - status = "okay"; -}; - -&pcie_phy { - status = "okay"; -}; - -&pio { - mmc0_pins_default: mmc0-pins { - mux { - function = "emmc"; - groups = "emmc_51"; - }; - conf-cmd-dat { - pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", - "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", - "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; - input-enable; - drive-strength = <4>; - mediatek,pull-up-adv = <1>; /* pull-up 10K */ - }; - conf-clk { - pins = "EMMC_CK"; - drive-strength = <6>; - mediatek,pull-down-adv = <2>; /* pull-down 50K */ - }; - conf-ds { - pins = "EMMC_DSL"; - mediatek,pull-down-adv = <2>; /* pull-down 50K */ - }; - conf-rst { - pins = "EMMC_RSTB"; - drive-strength = <4>; - mediatek,pull-up-adv = <1>; /* pull-up 10K */ - }; - }; - - mmc0_pins_uhs: mmc0-uhs-pins { - mux { - function = "emmc"; - groups = "emmc_51"; - }; - conf-cmd-dat { - pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", - "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", - "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; - input-enable; - drive-strength = <4>; - mediatek,pull-up-adv = <1>; /* pull-up 10K */ - }; - conf-clk { - pins = "EMMC_CK"; - drive-strength = <6>; - mediatek,pull-down-adv = <2>; /* pull-down 50K */ - }; - conf-ds { - pins = "EMMC_DSL"; - mediatek,pull-down-adv = <2>; /* pull-down 50K */ - }; - conf-rst { - pins = "EMMC_RSTB"; - drive-strength = <4>; - mediatek,pull-up-adv = <1>; /* pull-up 10K */ - }; - }; - - pcie_pins: pcie-pins { - mux { - function = "pcie"; - groups = "pcie_clk", "pcie_wake", "pcie_pereset"; - }; - }; - - spic_pins_g2: spic-pins-29-to-32 { - mux { - function = "spi"; - groups = "spi1_2"; - }; - }; - - spi_flash_pins: spi-flash-pins-33-to-38 { - mux { - function = "spi"; - groups = "spi0", "spi0_wp_hold"; - }; - conf-pu { - pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP"; - drive-strength = <8>; - mediatek,pull-up-adv = <0>; /* bias-disable */ - }; - conf-pd { - pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO"; - drive-strength = <8>; - mediatek,pull-down-adv = <0>; /* bias-disable */ - }; - }; - - uart1_pins: uart1-pins { - mux { - function = "uart"; - groups = "uart1"; - }; - }; - - uart2_pins: uart2-pins { - mux { - function = "uart"; - groups = "uart2"; - }; - }; - - wf_2g_5g_pins: wf_2g_5g-pins { - mux { - function = "wifi"; - groups = "wf_2g", "wf_5g"; - }; - conf { - pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", - "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", - "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", - "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", - "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", - "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", - "WF1_TOP_CLK", "WF1_TOP_DATA"; - drive-strength = <4>; - }; - }; - - wf_dbdc_pins: wf_dbdc-pins { - mux { - function = "wifi"; - groups = "wf_dbdc"; - }; - conf { - pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", - "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", - "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", - "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", - "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", - "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", - "WF1_TOP_CLK", "WF1_TOP_DATA"; - drive-strength = <4>; - }; - }; -}; - -&spi0 { - pinctrl-names = "default"; - pinctrl-0 = <&spi_flash_pins>; - cs-gpios = <0>, <0>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; -}; - -&spi1 { - pinctrl-names = "default"; - pinctrl-0 = <&spic_pins_g2>; - status = "okay"; - - proslic_spi: proslic_spi@0 { - compatible = "silabs,proslic_spi"; - reg = <0>; - spi-max-frequency = <10000000>; - spi-cpha = <1>; - spi-cpol = <1>; - channel_count = <1>; - debug_level = <4>; /* 1 = TRC, 2 = DBG, 4 = ERR */ - reset_gpio = <&pio 7 0>; - ig,enable-spi = <1>; /* 1: Enable, 0: Disable */ - }; -}; - -&gmac1 { - phy-mode = "2500base-x"; - phy-connection-type = "2500base-x"; - phy-handle = <&phy6>; -}; - -&switch { - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - label = "lan1"; - }; - - port@1 { - reg = <1>; - label = "lan2"; - }; - - port@2 { - reg = <2>; - label = "lan3"; - }; - - port@3 { - reg = <3>; - label = "lan4"; - }; - - port@4 { - reg = <4>; - label = "wan"; - }; - - port@5 { - reg = <5>; - label = "lan6"; - - phy-mode = "2500base-x"; - phy-handle = <&phy5>; - }; - - port@6 { - reg = <6>; - ethernet = <&gmac0>; - phy-mode = "2500base-x"; - - fixed-link { - speed = <2500>; - full-duplex; - pause; - }; - }; - }; -}; - -&ssusb { - vusb33-supply = <®_3p3v>; - vbus-supply = <®_5v>; - status = "okay"; -}; - -&uart0 { - status = "okay"; -}; - -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_pins>; - status = "okay"; -}; - -&uart2 { - pinctrl-names = "default"; - pinctrl-0 = <&uart2_pins>; - status = "okay"; -}; - -&usb_phy { - status = "okay"; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a.dtsi deleted file mode 100644 index 64f2cf3756..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986a.dtsi +++ /dev/null @@ -1,645 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2021 MediaTek Inc. - * Author: Sam.Shih - */ - -#include -#include -#include -#include -#include - -/ { - compatible = "mediatek,mt7986a"; - interrupt-parent = <&gic>; - #address-cells = <2>; - #size-cells = <2>; - - clk40m: oscillator-40m { - compatible = "fixed-clock"; - clock-frequency = <40000000>; - #clock-cells = <0>; - clock-output-names = "clkxtal"; - }; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - cpu0: cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - enable-method = "psci"; - reg = <0x0>; - #cooling-cells = <2>; - }; - - cpu1: cpu@1 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - enable-method = "psci"; - reg = <0x1>; - #cooling-cells = <2>; - }; - - cpu2: cpu@2 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - enable-method = "psci"; - reg = <0x2>; - #cooling-cells = <2>; - }; - - cpu3: cpu@3 { - device_type = "cpu"; - enable-method = "psci"; - compatible = "arm,cortex-a53"; - reg = <0x3>; - #cooling-cells = <2>; - }; - }; - - psci { - compatible = "arm,psci-0.2"; - method = "smc"; - }; - - reserved-memory { - #address-cells = <2>; - #size-cells = <2>; - ranges; - /* 192 KiB reserved for ARM Trusted Firmware (BL31) */ - secmon_reserved: secmon@43000000 { - reg = <0 0x43000000 0 0x30000>; - no-map; - }; - - wmcpu_emi: wmcpu-reserved@4fc00000 { - no-map; - reg = <0 0x4fc00000 0 0x00100000>; - }; - - wo_emi0: wo-emi@4fd00000 { - reg = <0 0x4fd00000 0 0x40000>; - no-map; - }; - - wo_emi1: wo-emi@4fd40000 { - reg = <0 0x4fd40000 0 0x40000>; - no-map; - }; - - wo_ilm0: wo-ilm@151e0000 { - reg = <0 0x151e0000 0 0x8000>; - no-map; - }; - - wo_ilm1: wo-ilm@151f0000 { - reg = <0 0x151f0000 0 0x8000>; - no-map; - }; - - wo_data: wo-data@4fd80000 { - reg = <0 0x4fd80000 0 0x240000>; - no-map; - }; - - wo_dlm0: wo-dlm@151e8000 { - reg = <0 0x151e8000 0 0x2000>; - no-map; - }; - - wo_dlm1: wo-dlm@151f8000 { - reg = <0 0x151f8000 0 0x2000>; - no-map; - }; - - wo_boot: wo-boot@15194000 { - reg = <0 0x15194000 0 0x1000>; - no-map; - }; - - }; - - timer { - compatible = "arm,armv8-timer"; - interrupt-parent = <&gic>; - interrupts = , - , - , - ; - }; - - soc { - #address-cells = <2>; - #size-cells = <2>; - compatible = "simple-bus"; - ranges; - - gic: interrupt-controller@c000000 { - compatible = "arm,gic-v3"; - #interrupt-cells = <3>; - interrupt-parent = <&gic>; - interrupt-controller; - reg = <0 0x0c000000 0 0x10000>, /* GICD */ - <0 0x0c080000 0 0x80000>, /* GICR */ - <0 0x0c400000 0 0x2000>, /* GICC */ - <0 0x0c410000 0 0x1000>, /* GICH */ - <0 0x0c420000 0 0x2000>; /* GICV */ - interrupts = ; - }; - - infracfg: infracfg@10001000 { - compatible = "mediatek,mt7986-infracfg", "syscon"; - reg = <0 0x10001000 0 0x1000>; - #clock-cells = <1>; - }; - - wed_pcie: wed-pcie@10003000 { - compatible = "mediatek,mt7986-wed-pcie", - "syscon"; - reg = <0 0x10003000 0 0x10>; - }; - - topckgen: topckgen@1001b000 { - compatible = "mediatek,mt7986-topckgen", "syscon"; - reg = <0 0x1001B000 0 0x1000>; - #clock-cells = <1>; - }; - - watchdog: watchdog@1001c000 { - compatible = "mediatek,mt7986-wdt"; - reg = <0 0x1001c000 0 0x1000>; - interrupts = ; - #reset-cells = <1>; - status = "disabled"; - }; - - apmixedsys: apmixedsys@1001e000 { - compatible = "mediatek,mt7986-apmixedsys"; - reg = <0 0x1001E000 0 0x1000>; - #clock-cells = <1>; - }; - - pio: pinctrl@1001f000 { - compatible = "mediatek,mt7986a-pinctrl"; - reg = <0 0x1001f000 0 0x1000>, - <0 0x11c30000 0 0x1000>, - <0 0x11c40000 0 0x1000>, - <0 0x11e20000 0 0x1000>, - <0 0x11e30000 0 0x1000>, - <0 0x11f00000 0 0x1000>, - <0 0x11f10000 0 0x1000>, - <0 0x1000b000 0 0x1000>; - reg-names = "gpio", "iocfg_rt", "iocfg_rb", "iocfg_lt", - "iocfg_lb", "iocfg_tr", "iocfg_tl", "eint"; - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pio 0 0 100>; - interrupt-controller; - interrupts = ; - interrupt-parent = <&gic>; - #interrupt-cells = <2>; - }; - - sgmiisys0: syscon@10060000 { - compatible = "mediatek,mt7986-sgmiisys_0", - "syscon"; - reg = <0 0x10060000 0 0x1000>; - #clock-cells = <1>; - }; - - sgmiisys1: syscon@10070000 { - compatible = "mediatek,mt7986-sgmiisys_1", - "syscon"; - reg = <0 0x10070000 0 0x1000>; - #clock-cells = <1>; - }; - - trng: rng@1020f000 { - compatible = "mediatek,mt7986-rng", - "mediatek,mt7623-rng"; - reg = <0 0x1020f000 0 0x100>; - clocks = <&infracfg CLK_INFRA_TRNG_CK>; - clock-names = "rng"; - status = "disabled"; - }; - - crypto: crypto@10320000 { - compatible = "inside-secure,safexcel-eip97"; - reg = <0 0x10320000 0 0x40000>; - interrupts = , - , - , - ; - interrupt-names = "ring0", "ring1", "ring2", "ring3"; - clocks = <&infracfg CLK_INFRA_EIP97_CK>; - clock-names = "infra_eip97_ck"; - assigned-clocks = <&topckgen CLK_TOP_EIP_B_SEL>; - assigned-clock-parents = <&apmixedsys CLK_APMIXED_NET2PLL>; - status = "disabled"; - }; - - pwm: pwm@10048000 { - compatible = "mediatek,mt7986-pwm"; - reg = <0 0x10048000 0 0x1000>; - #clock-cells = <1>; - #pwm-cells = <2>; - interrupts = ; - clocks = <&topckgen CLK_TOP_PWM_SEL>, - <&infracfg CLK_INFRA_PWM_STA>, - <&infracfg CLK_INFRA_PWM1_CK>, - <&infracfg CLK_INFRA_PWM2_CK>; - clock-names = "top", "main", "pwm1", "pwm2"; - status = "disabled"; - }; - - uart0: serial@11002000 { - compatible = "mediatek,mt7986-uart", - "mediatek,mt6577-uart"; - reg = <0 0x11002000 0 0x400>; - interrupts = ; - clocks = <&infracfg CLK_INFRA_UART0_SEL>, - <&infracfg CLK_INFRA_UART0_CK>; - clock-names = "baud", "bus"; - assigned-clocks = <&topckgen CLK_TOP_UART_SEL>, - <&infracfg CLK_INFRA_UART0_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_XTAL>, - <&topckgen CLK_TOP_UART_SEL>; - status = "disabled"; - }; - - uart1: serial@11003000 { - compatible = "mediatek,mt7986-uart", - "mediatek,mt6577-uart"; - reg = <0 0x11003000 0 0x400>; - interrupts = ; - clocks = <&infracfg CLK_INFRA_UART1_SEL>, - <&infracfg CLK_INFRA_UART1_CK>; - clock-names = "baud", "bus"; - assigned-clocks = <&infracfg CLK_INFRA_UART1_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>; - status = "disabled"; - }; - - uart2: serial@11004000 { - compatible = "mediatek,mt7986-uart", - "mediatek,mt6577-uart"; - reg = <0 0x11004000 0 0x400>; - interrupts = ; - clocks = <&infracfg CLK_INFRA_UART2_SEL>, - <&infracfg CLK_INFRA_UART2_CK>; - clock-names = "baud", "bus"; - assigned-clocks = <&infracfg CLK_INFRA_UART2_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>; - status = "disabled"; - }; - - i2c0: i2c@11008000 { - compatible = "mediatek,mt7986-i2c"; - reg = <0 0x11008000 0 0x90>, - <0 0x10217080 0 0x80>; - interrupts = ; - clock-div = <5>; - clocks = <&infracfg CLK_INFRA_I2C0_CK>, - <&infracfg CLK_INFRA_AP_DMA_CK>; - clock-names = "main", "dma"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - spi0: spi@1100a000 { - compatible = "mediatek,mt7986-spi-ipm", "mediatek,spi-ipm"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0 0x1100a000 0 0x100>; - interrupts = ; - clocks = <&topckgen CLK_TOP_MPLL_D2>, - <&topckgen CLK_TOP_SPI_SEL>, - <&infracfg CLK_INFRA_SPI0_CK>, - <&infracfg CLK_INFRA_SPI0_HCK_CK>; - clock-names = "parent-clk", "sel-clk", "spi-clk", "hclk"; - status = "disabled"; - }; - - spi1: spi@1100b000 { - compatible = "mediatek,mt7986-spi-ipm", "mediatek,spi-ipm"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0 0x1100b000 0 0x100>; - interrupts = ; - clocks = <&topckgen CLK_TOP_MPLL_D2>, - <&topckgen CLK_TOP_SPIM_MST_SEL>, - <&infracfg CLK_INFRA_SPI1_CK>, - <&infracfg CLK_INFRA_SPI1_HCK_CK>; - clock-names = "parent-clk", "sel-clk", "spi-clk", "hclk"; - status = "disabled"; - }; - - auxadc: adc@1100d000 { - compatible = "mediatek,mt7986-auxadc"; - reg = <0 0x1100d000 0 0x1000>; - clocks = <&infracfg CLK_INFRA_ADC_26M_CK>; - clock-names = "main"; - #io-channel-cells = <1>; - status = "disabled"; - }; - - ssusb: usb@11200000 { - compatible = "mediatek,mt7986-xhci", - "mediatek,mtk-xhci"; - reg = <0 0x11200000 0 0x2e00>, - <0 0x11203e00 0 0x0100>; - reg-names = "mac", "ippc"; - interrupts = ; - clocks = <&infracfg CLK_INFRA_IUSB_SYS_CK>, - <&infracfg CLK_INFRA_IUSB_CK>, - <&infracfg CLK_INFRA_IUSB_133_CK>, - <&infracfg CLK_INFRA_IUSB_66M_CK>, - <&topckgen CLK_TOP_U2U3_XHCI_SEL>; - clock-names = "sys_ck", - "ref_ck", - "mcu_ck", - "dma_ck", - "xhci_ck"; - phys = <&u2port0 PHY_TYPE_USB2>, - <&u3port0 PHY_TYPE_USB3>, - <&u2port1 PHY_TYPE_USB2>; - status = "disabled"; - }; - - mmc0: mmc@11230000 { - compatible = "mediatek,mt7986-mmc"; - reg = <0 0x11230000 0 0x1000>, - <0 0x11c20000 0 0x1000>; - interrupts = ; - clocks = <&topckgen CLK_TOP_EMMC_416M_SEL>, - <&infracfg CLK_INFRA_MSDC_HCK_CK>, - <&infracfg CLK_INFRA_MSDC_CK>, - <&infracfg CLK_INFRA_MSDC_133M_CK>, - <&infracfg CLK_INFRA_MSDC_66M_CK>; - clock-names = "source", "hclk", "source_cg", "bus_clk", - "sys_cg"; - status = "disabled"; - }; - - thermal: thermal@1100c800 { - #thermal-sensor-cells = <1>; - compatible = "mediatek,mt7986-thermal"; - reg = <0 0x1100c800 0 0x800>; - interrupts = ; - clocks = <&infracfg CLK_INFRA_THERM_CK>, - <&infracfg CLK_INFRA_ADC_26M_CK>, - <&infracfg CLK_INFRA_ADC_FRC_CK>; - clock-names = "therm", "auxadc", "adc_32k"; - mediatek,auxadc = <&auxadc>; - mediatek,apmixedsys = <&apmixedsys>; - nvmem-cells = <&thermal_calibration>; - nvmem-cell-names = "calibration-data"; - }; - - pcie: pcie@11280000 { - compatible = "mediatek,mt7986-pcie", - "mediatek,mt8192-pcie"; - device_type = "pci"; - #address-cells = <3>; - #size-cells = <2>; - reg = <0x00 0x11280000 0x00 0x4000>; - reg-names = "pcie-mac"; - interrupts = ; - bus-range = <0x00 0xff>; - ranges = <0x82000000 0x00 0x20000000 0x00 - 0x20000000 0x00 0x10000000>; - clocks = <&infracfg CLK_INFRA_IPCIE_PIPE_CK>, - <&infracfg CLK_INFRA_IPCIE_CK>, - <&infracfg CLK_INFRA_IPCIER_CK>, - <&infracfg CLK_INFRA_IPCIEB_CK>; - clock-names = "pl_250m", "tl_26m", "peri_26m", "top_133m"; - status = "disabled"; - - phys = <&pcie_port PHY_TYPE_PCIE>; - phy-names = "pcie-phy"; - - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0x7>; - interrupt-map = <0 0 0 1 &pcie_intc 0>, - <0 0 0 2 &pcie_intc 1>, - <0 0 0 3 &pcie_intc 2>, - <0 0 0 4 &pcie_intc 3>; - pcie_intc: interrupt-controller { - #address-cells = <0>; - #interrupt-cells = <1>; - interrupt-controller; - }; - }; - - pcie_phy: t-phy@11c00000 { - compatible = "mediatek,mt7986-tphy", - "mediatek,generic-tphy-v2"; - #address-cells = <2>; - #size-cells = <2>; - ranges; - status = "disabled"; - - pcie_port: pcie-phy@11c00000 { - reg = <0 0x11c00000 0 0x20000>; - clocks = <&clk40m>; - clock-names = "ref"; - #phy-cells = <1>; - }; - }; - - efuse: efuse@11d00000 { - compatible = "mediatek,mt7986-efuse", "mediatek,efuse"; - reg = <0 0x11d00000 0 0x1000>; - #address-cells = <1>; - #size-cells = <1>; - - thermal_calibration: calib@274 { - reg = <0x274 0xc>; - }; - }; - - usb_phy: t-phy@11e10000 { - compatible = "mediatek,mt7986-tphy", - "mediatek,generic-tphy-v2"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0 0x11e10000 0x1700>; - status = "disabled"; - - u2port0: usb-phy@0 { - reg = <0x0 0x700>; - clocks = <&topckgen CLK_TOP_DA_U2_REFSEL>, - <&topckgen CLK_TOP_DA_U2_CK_1P_SEL>; - clock-names = "ref", "da_ref"; - #phy-cells = <1>; - }; - - u3port0: usb-phy@700 { - reg = <0x700 0x900>; - clocks = <&topckgen CLK_TOP_USB3_PHY_SEL>; - clock-names = "ref"; - #phy-cells = <1>; - }; - - u2port1: usb-phy@1000 { - reg = <0x1000 0x700>; - clocks = <&topckgen CLK_TOP_DA_U2_REFSEL>, - <&topckgen CLK_TOP_DA_U2_CK_1P_SEL>; - clock-names = "ref", "da_ref"; - #phy-cells = <1>; - }; - }; - - ethsys: syscon@15000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "mediatek,mt7986-ethsys", - "syscon"; - reg = <0 0x15000000 0 0x1000>; - #clock-cells = <1>; - #reset-cells = <1>; - }; - - wed0: wed@15010000 { - compatible = "mediatek,mt7986-wed", - "syscon"; - reg = <0 0x15010000 0 0x1000>; - interrupt-parent = <&gic>; - interrupts = ; - memory-region = <&wo_emi0>, <&wo_ilm0>, <&wo_dlm0>, - <&wo_data>, <&wo_boot>; - memory-region-names = "wo-emi", "wo-ilm", "wo-dlm", - "wo-data", "wo-boot"; - mediatek,wo-ccif = <&wo_ccif0>; - }; - - wed1: wed@15011000 { - compatible = "mediatek,mt7986-wed", - "syscon"; - reg = <0 0x15011000 0 0x1000>; - interrupt-parent = <&gic>; - interrupts = ; - memory-region = <&wo_emi1>, <&wo_ilm1>, <&wo_dlm1>, - <&wo_data>, <&wo_boot>; - memory-region-names = "wo-emi", "wo-ilm", "wo-dlm", - "wo-data", "wo-boot"; - mediatek,wo-ccif = <&wo_ccif1>; - }; - - wo_ccif0: syscon@151a5000 { - compatible = "mediatek,mt7986-wo-ccif", "syscon"; - reg = <0 0x151a5000 0 0x1000>; - interrupt-parent = <&gic>; - interrupts = ; - }; - - wo_ccif1: syscon@151ad000 { - compatible = "mediatek,mt7986-wo-ccif", "syscon"; - reg = <0 0x151ad000 0 0x1000>; - interrupt-parent = <&gic>; - interrupts = ; - }; - - eth: ethernet@15100000 { - compatible = "mediatek,mt7986-eth"; - reg = <0 0x15100000 0 0x80000>; - interrupts = , - , - , - ; - clocks = <ðsys CLK_ETH_FE_EN>, - <ðsys CLK_ETH_GP2_EN>, - <ðsys CLK_ETH_GP1_EN>, - <ðsys CLK_ETH_WOCPU1_EN>, - <ðsys CLK_ETH_WOCPU0_EN>, - <&sgmiisys0 CLK_SGMII0_TX250M_EN>, - <&sgmiisys0 CLK_SGMII0_RX250M_EN>, - <&sgmiisys0 CLK_SGMII0_CDR_REF>, - <&sgmiisys0 CLK_SGMII0_CDR_FB>, - <&sgmiisys1 CLK_SGMII1_TX250M_EN>, - <&sgmiisys1 CLK_SGMII1_RX250M_EN>, - <&sgmiisys1 CLK_SGMII1_CDR_REF>, - <&sgmiisys1 CLK_SGMII1_CDR_FB>, - <&topckgen CLK_TOP_NETSYS_SEL>, - <&topckgen CLK_TOP_NETSYS_500M_SEL>; - clock-names = "fe", "gp2", "gp1", "wocpu1", "wocpu0", - "sgmii_tx250m", "sgmii_rx250m", - "sgmii_cdr_ref", "sgmii_cdr_fb", - "sgmii2_tx250m", "sgmii2_rx250m", - "sgmii2_cdr_ref", "sgmii2_cdr_fb", - "netsys0", "netsys1"; - assigned-clocks = <&topckgen CLK_TOP_NETSYS_2X_SEL>, - <&topckgen CLK_TOP_SGM_325M_SEL>; - assigned-clock-parents = <&apmixedsys CLK_APMIXED_NET2PLL>, - <&apmixedsys CLK_APMIXED_SGMPLL>; - mediatek,ethsys = <ðsys>; - mediatek,sgmiisys = <&sgmiisys0>, <&sgmiisys1>; - mediatek,wed-pcie = <&wed_pcie>; - mediatek,wed = <&wed0>, <&wed1>; - #reset-cells = <1>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - wifi: wifi@18000000 { - compatible = "mediatek,mt7986-wmac"; - resets = <&watchdog MT7986_TOPRGU_CONSYS_SW_RST>; - reset-names = "consys"; - clocks = <&topckgen CLK_TOP_CONN_MCUSYS_SEL>, - <&topckgen CLK_TOP_AP2CNN_HOST_SEL>; - clock-names = "mcu", "ap2conn"; - reg = <0 0x18000000 0 0x1000000>, - <0 0x10003000 0 0x1000>, - <0 0x11d10000 0 0x1000>; - interrupts = , - , - , - ; - memory-region = <&wmcpu_emi>; - }; - }; - - thermal-zones { - cpu_thermal: cpu-thermal { - polling-delay-passive = <1000>; - polling-delay = <1000>; - thermal-sensors = <&thermal 0>; - - trips { - cpu_trip_crit: crit { - temperature = <125000>; - hysteresis = <2000>; - type = "critical"; - }; - - cpu_trip_hot: hot { - temperature = <120000>; - hysteresis = <2000>; - type = "hot"; - }; - - cpu_trip_active_high: active-high { - temperature = <115000>; - hysteresis = <2000>; - type = "active"; - }; - - cpu_trip_active_med: active-med { - temperature = <85000>; - hysteresis = <2000>; - type = "active"; - }; - - cpu_trip_active_low: active-low { - temperature = <60000>; - hysteresis = <2000>; - type = "active"; - }; - }; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts deleted file mode 100644 index 8cd094f7c3..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts +++ /dev/null @@ -1,194 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2021 MediaTek Inc. - * Author: Sam.Shih - */ - -/dts-v1/; -#include "mt7986b.dtsi" - -/ { - model = "MediaTek MT7986b RFB"; - compatible = "mediatek,mt7986b-rfb"; - - aliases { - serial0 = &uart0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory { - reg = <0 0x40000000 0 0x40000000>; - }; - - reg_3p3v: regulator-3p3v { - compatible = "regulator-fixed"; - regulator-name = "fixed-3.3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; - }; - - reg_5v: regulator-5v { - compatible = "regulator-fixed"; - regulator-name = "fixed-5V"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-boot-on; - regulator-always-on; - }; -}; - -&ssusb { - vusb33-supply = <®_3p3v>; - vbus-supply = <®_5v>; - status = "okay"; -}; - -&uart0 { - status = "okay"; -}; - -&usb_phy { - status = "okay"; -}; - -&wifi { - status = "okay"; - pinctrl-names = "default", "dbdc"; - pinctrl-0 = <&wf_2g_5g_pins>; - pinctrl-1 = <&wf_dbdc_pins>; -}; - -ð { - status = "okay"; - - gmac0: mac@0 { - compatible = "mediatek,eth-mac"; - reg = <0>; - phy-mode = "2500base-x"; - - fixed-link { - speed = <2500>; - full-duplex; - pause; - }; - }; - - gmac1: mac@1 { - compatible = "mediatek,eth-mac"; - reg = <1>; - phy-mode = "2500base-x"; - - fixed-link { - speed = <2500>; - full-duplex; - pause; - }; - }; - - mdio: mdio-bus { - #address-cells = <1>; - #size-cells = <0>; - - phy5: phy@5 { - compatible = "ethernet-phy-id67c9.de0a"; - reg = <5>; - reset-gpios = <&pio 6 1>; - reset-deassert-us = <20000>; - phy-mode = "2500base-x"; - }; - - phy6: phy@6 { - compatible = "ethernet-phy-id67c9.de0a"; - reg = <6>; - phy-mode = "2500base-x"; - }; - - switch@1f { - compatible = "mediatek,mt7531"; - reg = <31>; - reset-gpios = <&pio 5 0>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - label = "lan0"; - }; - - port@1 { - reg = <1>; - label = "lan1"; - }; - - port@2 { - reg = <2>; - label = "lan2"; - }; - - port@3 { - reg = <3>; - label = "lan3"; - }; - - port@6 { - reg = <6>; - ethernet = <&gmac0>; - phy-mode = "2500base-x"; - - fixed-link { - speed = <2500>; - full-duplex; - pause; - }; - }; - }; - }; - }; -}; - -&crypto { - status = "okay"; -}; - -&pio { - wf_2g_5g_pins: wf_2g_5g-pins { - mux { - function = "wifi"; - groups = "wf_2g", "wf_5g"; - }; - conf { - pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", - "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", - "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", - "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", - "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", - "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", - "WF1_TOP_CLK", "WF1_TOP_DATA"; - drive-strength = <4>; - }; - }; - - wf_dbdc_pins: wf_dbdc-pins { - mux { - function = "wifi"; - groups = "wf_dbdc"; - }; - conf { - pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", - "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", - "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", - "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", - "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", - "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", - "WF1_TOP_CLK", "WF1_TOP_DATA"; - drive-strength = <4>; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986b.dtsi b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986b.dtsi deleted file mode 100644 index db5189664c..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7986b.dtsi +++ /dev/null @@ -1,15 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2021 MediaTek Inc. - * Author: Sam.Shih - */ - -#include "mt7986a.dtsi" -/ { - compatible = "mediatek,mt7986b"; -}; - -&pio { - compatible = "mediatek,mt7986b-pinctrl"; - gpio-ranges = <&pio 0 0 41>, <&pio 66 66 35>; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-emmc.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-emmc.dtso deleted file mode 100644 index 3f8ac2ae38..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-emmc.dtso +++ /dev/null @@ -1,33 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2021 MediaTek Inc. - * Author: Frank Wunderlich - */ - -/dts-v1/; -/plugin/; - -/ { - compatible = "mediatek,mt7988a-rfb", "mediatek,mt7988a"; - - fragment@0 { - target = <&mmc0>; - __overlay__ { - pinctrl-names = "default", "state_uhs"; - pinctrl-0 = <&mmc0_pins_emmc_51>; - pinctrl-1 = <&mmc0_pins_emmc_51>; - bus-width = <8>; - max-frequency = <200000000>; - cap-mmc-highspeed; - mmc-hs200-1_8v; - mmc-hs400-1_8v; - hs400-ds-delay = <0x12814>; - vqmmc-supply = <®_1p8v>; - vmmc-supply = <®_3p3v>; - non-removable; - no-sd; - no-sdio; - status = "okay"; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth1-aqr.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth1-aqr.dtso deleted file mode 100644 index d21a61ad19..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth1-aqr.dtso +++ /dev/null @@ -1,41 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2022 MediaTek Inc. - * Author: Sam.Shih - */ - -/dts-v1/; -/plugin/; - -#include - -/ { - compatible = "mediatek,mt7988a-rfb", "mediatek,mt7988a"; - - fragment@0 { - target = <&mdio_bus>; - __overlay__ { - #address-cells = <1>; - #size-cells = <0>; - - /* external Aquantia AQR113C */ - phy0: ethernet-phy@0 { - reg = <0>; - compatible = "ethernet-phy-ieee802.3-c45"; - reset-gpios = <&pio 72 GPIO_ACTIVE_LOW>; - reset-assert-us = <100000>; - reset-deassert-us = <221000>; - }; - }; - }; - - fragment@1 { - target = <&gmac1>; - __overlay__ { - phy-mode = "usxgmii"; - phy-connection-type = "usxgmii"; - phy = <&phy0>; - status = "okay"; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth1-i2p5g-phy.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth1-i2p5g-phy.dtso deleted file mode 100644 index 86ab7566dc..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth1-i2p5g-phy.dtso +++ /dev/null @@ -1,30 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2022 MediaTek Inc. - * Author: Sam.Shih - */ - -/dts-v1/; -/plugin/; - -/ { - compatible = "mediatek,mt7988a-rfb", "mediatek,mt7988a"; - - fragment@0 { - target = <&gmac1>; - __overlay__ { - phy-mode = "internal"; - phy-connection-type = "internal"; - phy = <&int_2p5g_phy>; - status = "okay"; - }; - }; - - fragment@1 { - target = <&int_2p5g_phy>; - __overlay__ { - pinctrl-names = "i2p5gbe-led"; - pinctrl-0 = <&i2p5gbe_led0_pins>; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth1-mxl.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth1-mxl.dtso deleted file mode 100644 index 34a23bbd7e..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth1-mxl.dtso +++ /dev/null @@ -1,39 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2022 MediaTek Inc. - * Author: Sam.Shih - */ - -/dts-v1/; -/plugin/; - -#include - -/ { - compatible = "mediatek,mt7988a-rfb", "mediatek,mt7988a"; - - fragment@0 { - target = <&mdio_bus>; - __overlay__ { - #address-cells = <1>; - #size-cells = <0>; - - /* external Maxlinear GPY211C */ - phy13: ethernet-phy@13 { - reg = <13>; - compatible = "ethernet-phy-ieee802.3-c45"; - phy-mode = "2500base-x"; - }; - }; - }; - - fragment@1 { - target = <&gmac1>; - __overlay__ { - phy-mode = "2500base-x"; - phy-connection-type = "2500base-x"; - phy = <&phy13>; - status = "okay"; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth1-sfp.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth1-sfp.dtso deleted file mode 100644 index ba40a119cb..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth1-sfp.dtso +++ /dev/null @@ -1,47 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2022 MediaTek Inc. - * Author: Sam.Shih - */ - -/dts-v1/; -/plugin/; - -#include - -/ { - compatible = "mediatek,mt7988a-rfb", "mediatek,mt7988a"; - - fragment@0 { - target = <&i2c2>; - __overlay__ { - pinctrl-names = "default"; - pinctrl-0 = <&i2c2_0_pins>; - status = "okay"; - }; - }; - - fragment@1 { - target-path = "/"; - __overlay__ { - sfp_esp1: sfp@1 { - compatible = "sff,sfp"; - i2c-bus = <&i2c2>; - mod-def0-gpios = <&pio 82 GPIO_ACTIVE_LOW>; - los-gpios = <&pio 81 GPIO_ACTIVE_HIGH>; - tx-disable-gpios = <&pio 36 GPIO_ACTIVE_HIGH>; - maximum-power-milliwatt = <3000>; - }; - }; - }; - - fragment@2 { - target = <&gmac1>; - __overlay__ { - phy-mode = "10gbase-r"; - managed = "in-band-status"; - sfp = <&sfp_esp1>; - status = "okay"; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth2-aqr.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth2-aqr.dtso deleted file mode 100644 index 140391fc45..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth2-aqr.dtso +++ /dev/null @@ -1,41 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2022 MediaTek Inc. - * Author: Sam.Shih - */ - -/dts-v1/; -/plugin/; - -#include - -/ { - compatible = "mediatek,mt7988a-rfb", "mediatek,mt7988a"; - - fragment@0 { - target = <&mdio_bus>; - __overlay__ { - #address-cells = <1>; - #size-cells = <0>; - - /* external Aquantia AQR113C */ - phy8: ethernet-phy@8 { - reg = <8>; - compatible = "ethernet-phy-ieee802.3-c45"; - reset-gpios = <&pio 71 GPIO_ACTIVE_LOW>; - reset-assert-us = <100000>; - reset-deassert-us = <221000>; - }; - }; - }; - - fragment@1 { - target = <&gmac2>; - __overlay__ { - phy-mode = "usxgmii"; - phy-connection-type = "usxgmii"; - phy = <&phy8>; - status = "okay"; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth2-mxl.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth2-mxl.dtso deleted file mode 100644 index 19e0b2799f..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth2-mxl.dtso +++ /dev/null @@ -1,39 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2022 MediaTek Inc. - * Author: Sam.Shih - */ - -/dts-v1/; -/plugin/; - -#include - -/ { - compatible = "mediatek,mt7988a-rfb", "mediatek,mt7988a"; - - fragment@0 { - target = <&mdio_bus>; - __overlay__ { - #address-cells = <1>; - #size-cells = <0>; - - /* external Maxlinear GPY211C */ - phy5: ethernet-phy@5 { - reg = <5>; - compatible = "ethernet-phy-ieee802.3-c45"; - phy-mode = "2500base-x"; - }; - }; - }; - - fragment@1 { - target = <&gmac2>; - __overlay__ { - phy-mode = "2500base-x"; - phy-connection-type = "2500base-x"; - phy = <&phy5>; - status = "okay"; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth2-sfp.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth2-sfp.dtso deleted file mode 100644 index b9aabd2726..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-eth2-sfp.dtso +++ /dev/null @@ -1,47 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2022 MediaTek Inc. - * Author: Sam.Shih - */ - -/dts-v1/; -/plugin/; - -#include - -/ { - compatible = "mediatek,mt7988a-rfb", "mediatek,mt7988a"; - - fragment@0 { - target = <&i2c1>; - __overlay__ { - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_sfp_pins>; - status = "okay"; - }; - }; - - fragment@1 { - target-path = "/"; - __overlay__ { - sfp_esp0: sfp@0 { - compatible = "sff,sfp"; - i2c-bus = <&i2c1>; - mod-def0-gpios = <&pio 35 GPIO_ACTIVE_LOW>; - los-gpios = <&pio 33 GPIO_ACTIVE_HIGH>; - tx-disable-gpios = <&pio 29 GPIO_ACTIVE_HIGH>; - maximum-power-milliwatt = <3000>; - }; - }; - }; - - fragment@2 { - target = <&gmac2>; - __overlay__ { - phy-mode = "10gbase-r"; - managed = "in-band-status"; - sfp = <&sfp_esp0>; - status = "okay"; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-sd.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-sd.dtso deleted file mode 100644 index 04472cc12d..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-sd.dtso +++ /dev/null @@ -1,31 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2023 MediaTek Inc. - * Author: Frank Wunderlich - */ - -/dts-v1/; -/plugin/; - -#include - -/ { - compatible = "mediatek,mt7988a-rfb", "mediatek,mt7988a"; - - fragment@1 { - target-path = <&mmc0>; - __overlay__ { - pinctrl-names = "default", "state_uhs"; - pinctrl-0 = <&mmc0_pins_sdcard>; - pinctrl-1 = <&mmc0_pins_sdcard>; - cd-gpios = <&pio 69 GPIO_ACTIVE_LOW>; - bus-width = <4>; - max-frequency = <52000000>; - cap-sd-highspeed; - vmmc-supply = <®_3p3v>; - vqmmc-supply = <®_3p3v>; - no-mmc; - status = "okay"; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-snfi-nand.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-snfi-nand.dtso deleted file mode 100644 index 86b0042f64..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-snfi-nand.dtso +++ /dev/null @@ -1,69 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2022 MediaTek Inc. - * Author: Sam.Shih - */ - -/dts-v1/; -/plugin/; - -/ { - compatible = "mediatek,mt7988a-rfb", "mediatek,mt7988a"; - - fragment@0 { - target = <&snand>; - __overlay__ { - status = "okay"; - - flash@0 { - compatible = "spi-nand"; - reg = <0>; - spi-max-frequency = <52000000>; - spi-tx-bus-width = <4>; - spi-rx-bus-width = <4>; - mediatek,nmbm; - mediatek,bmt-max-ratio = <1>; - mediatek,bmt-max-reserved-blocks = <64>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "BL2"; - reg = <0x00000 0x0100000>; - read-only; - }; - - partition@100000 { - label = "u-boot-env"; - reg = <0x0100000 0x0080000>; - }; - - partition@180000 { - label = "Factory"; - reg = <0x180000 0x0400000>; - }; - - partition@580000 { - label = "FIP"; - reg = <0x580000 0x0200000>; - }; - - partition@780000 { - label = "ubi"; - reg = <0x780000 0x7080000>; - }; - }; - }; - }; - }; - - fragment@1 { - target = <&bch>; - __overlay__ { - status = "okay"; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-spim-nand.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-spim-nand.dtso deleted file mode 100644 index a9eca00d44..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-spim-nand.dtso +++ /dev/null @@ -1,64 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2022 MediaTek Inc. - * Author: Sam.Shih - */ - -/dts-v1/; -/plugin/; - -/ { - compatible = "mediatek,mt7988a-rfb", "mediatek,mt7988a"; - - fragment@0 { - target = <&spi0>; - __overlay__ { - pinctrl-names = "default"; - pinctrl-0 = <&spi0_flash_pins>; - status = "okay"; - - flash@0 { - compatible = "spi-nand"; - reg = <0>; - spi-max-frequency = <52000000>; - spi-tx-bus-width = <4>; - spi-rx-bus-width = <4>; - mediatek,nmbm; - mediatek,bmt-max-ratio = <1>; - mediatek,bmt-max-reserved-blocks = <64>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "BL2"; - reg = <0x00000 0x0100000>; - read-only; - }; - - partition@100000 { - label = "u-boot-env"; - reg = <0x0100000 0x0080000>; - }; - - partition@180000 { - label = "Factory"; - reg = <0x180000 0x0400000>; - }; - - partition@580000 { - label = "FIP"; - reg = <0x580000 0x0200000>; - }; - - partition@780000 { - label = "ubi"; - reg = <0x780000 0x7080000>; - }; - }; - }; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-spim-nor.dtso b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-spim-nor.dtso deleted file mode 100644 index 33bd57b3fb..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb-spim-nor.dtso +++ /dev/null @@ -1,59 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2022 MediaTek Inc. - * Author: Sam.Shih - */ - -/dts-v1/; -/plugin/; - -/ { - compatible = "mediatek,mt7988a-rfb", "mediatek,mt7988a"; - - fragment@0 { - target = <&spi2>; - __overlay__ { - pinctrl-names = "default"; - pinctrl-0 = <&spi2_flash_pins>; - status = "okay"; - - flash@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "jedec,spi-nor"; - spi-cal-enable; - spi-cal-mode = "read-data"; - spi-cal-datalen = <7>; - spi-cal-data = /bits/ 8 < - 0x53 0x46 0x5F 0x42 0x4F 0x4F 0x54>; /* SF_BOOT */ - spi-cal-addrlen = <1>; - spi-cal-addr = /bits/ 32 <0x0>; - reg = <0>; - spi-max-frequency = <52000000>; - spi-tx-bus-width = <4>; - spi-rx-bus-width = <4>; - - partition@00000 { - label = "BL2"; - reg = <0x00000 0x0040000>; - }; - partition@40000 { - label = "u-boot-env"; - reg = <0x40000 0x0010000>; - }; - partition@50000 { - label = "Factory"; - reg = <0x50000 0x0200000>; - }; - partition@250000 { - label = "FIP"; - reg = <0x250000 0x0080000>; - }; - partition@2D0000 { - label = "firmware"; - reg = <0x2D0000 0x1D30000>; - }; - }; - }; - }; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb.dts b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb.dts deleted file mode 100644 index 11dbf98301..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a-rfb.dts +++ /dev/null @@ -1,200 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2022 MediaTek Inc. - * Author: Sam.Shih - */ - -/dts-v1/; -#include "mt7988a.dtsi" -#include -#include -#include - -/ { - model = "MediaTek MT7988A Reference Board"; - compatible = "mediatek,mt7988a-rfb", - "mediatek,mt7988"; - - chosen { - bootargs = "console=ttyS0,115200n1 loglevel=8 \ - earlycon=uart8250,mmio32,0x11000000 \ - pci=pcie_bus_perf"; - }; - - memory { - reg = <0 0x40000000 0 0x40000000>; - }; -}; - -ð { - pinctrl-0 = <&mdio0_pins>; - pinctrl-names = "default"; -}; - -&gmac0 { - status = "okay"; -}; - -&cpu0 { - proc-supply = <&rt5190_buck3>; -}; - -&cpu1 { - proc-supply = <&rt5190_buck3>; -}; - -&cpu2 { - proc-supply = <&rt5190_buck3>; -}; - -&cpu3 { - proc-supply = <&rt5190_buck3>; -}; - -&cci { - proc-supply = <&rt5190_buck3>; -}; - -ð { - status = "okay"; -}; - -&switch { - status = "okay"; -}; - -&gsw_phy0 { - pinctrl-names = "gbe-led"; - pinctrl-0 = <&gbe0_led0_pins>; -}; - -&gsw_phy0_led0 { - status = "okay"; - color = ; -}; - -&gsw_phy1 { - pinctrl-names = "gbe-led"; - pinctrl-0 = <&gbe1_led0_pins>; -}; - -&gsw_phy1_led0 { - status = "okay"; - color = ; -}; - -&gsw_phy2 { - pinctrl-names = "gbe-led"; - pinctrl-0 = <&gbe2_led0_pins>; -}; - -&gsw_phy2_led0 { - status = "okay"; - color = ; -}; - -&gsw_phy3 { - pinctrl-names = "gbe-led"; - pinctrl-0 = <&gbe3_led0_pins>; -}; - -&gsw_phy3_led0 { - status = "okay"; - color = ; -}; - -&i2c0 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins>; - status = "okay"; - - rt5190a_64: rt5190a@64 { - compatible = "richtek,rt5190a"; - reg = <0x64>; - /*interrupts-extended = <&gpio26 0 IRQ_TYPE_LEVEL_LOW>;*/ - vin2-supply = <&rt5190_buck1>; - vin3-supply = <&rt5190_buck1>; - vin4-supply = <&rt5190_buck1>; - - regulators { - rt5190_buck1: buck1 { - regulator-name = "rt5190a-buck1"; - regulator-min-microvolt = <5090000>; - regulator-max-microvolt = <5090000>; - regulator-allowed-modes = - ; - regulator-boot-on; - regulator-always-on; - }; - buck2 { - regulator-name = "vcore"; - regulator-min-microvolt = <600000>; - regulator-max-microvolt = <1400000>; - regulator-boot-on; - regulator-always-on; - }; - rt5190_buck3: buck3 { - regulator-name = "vproc"; - regulator-min-microvolt = <600000>; - regulator-max-microvolt = <1400000>; - regulator-boot-on; - }; - buck4 { - regulator-name = "rt5190a-buck4"; - regulator-min-microvolt = <850000>; - regulator-max-microvolt = <850000>; - regulator-allowed-modes = - ; - regulator-boot-on; - regulator-always-on; - }; - ldo { - regulator-name = "rt5190a-ldo"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-boot-on; - regulator-always-on; - }; - }; - }; -}; - -&pcie0 { - status = "okay"; -}; - -&pcie1 { - status = "okay"; -}; - -&pcie2 { - status = "disabled"; -}; - -&pcie3 { - status = "okay"; -}; - -&ssusb0 { - status = "okay"; -}; - -&ssusb1 { - status = "okay"; -}; - -&tphy { - status = "okay"; -}; - -&uart0 { - status = "okay"; -}; - -&watchdog { - status = "okay"; -}; - -&xphy { - status = "okay"; -}; diff --git a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a.dtsi b/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a.dtsi deleted file mode 100644 index 81410c017b..0000000000 --- a/target/linux/mediatek/files-5.15/arch/arm64/boot/dts/mediatek/mt7988a.dtsi +++ /dev/null @@ -1,1456 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0 OR MIT) -/* - * Copyright (C) 2023 MediaTek Inc. - * Author: Sam.Shih - */ - -#include -#include -#include -#include -#include -#include -#include -#include - -/ { - compatible = "mediatek,mt7988"; - interrupt-parent = <&gic>; - #address-cells = <2>; - #size-cells = <2>; - - cci: cci { - compatible = "mediatek,mt7988-cci", - "mediatek,mt8183-cci"; - clocks = <&mcusys CLK_MCU_BUS_DIV_SEL>, - <&topckgen CLK_TOP_XTAL>; - clock-names = "cci", "intermediate"; - operating-points-v2 = <&cci_opp>; - }; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - cpu0: cpu@0 { - compatible = "arm,cortex-a73"; - reg = <0x0>; - device_type = "cpu"; - enable-method = "psci"; - clocks = <&mcusys CLK_MCU_ARM_DIV_SEL>, - <&topckgen CLK_TOP_XTAL>; - clock-names = "cpu", "intermediate"; - operating-points-v2 = <&cluster0_opp>; - mediatek,cci = <&cci>; - }; - - cpu1: cpu@1 { - compatible = "arm,cortex-a73"; - reg = <0x1>; - device_type = "cpu"; - enable-method = "psci"; - clocks = <&mcusys CLK_MCU_ARM_DIV_SEL>, - <&topckgen CLK_TOP_XTAL>; - clock-names = "cpu", "intermediate"; - operating-points-v2 = <&cluster0_opp>; - mediatek,cci = <&cci>; - }; - - cpu2: cpu@2 { - compatible = "arm,cortex-a73"; - reg = <0x2>; - device_type = "cpu"; - enable-method = "psci"; - clocks = <&mcusys CLK_MCU_ARM_DIV_SEL>, - <&topckgen CLK_TOP_XTAL>; - clock-names = "cpu", "intermediate"; - operating-points-v2 = <&cluster0_opp>; - mediatek,cci = <&cci>; - }; - - cpu3: cpu@3 { - compatible = "arm,cortex-a73"; - reg = <0x3>; - device_type = "cpu"; - enable-method = "psci"; - clocks = <&mcusys CLK_MCU_ARM_DIV_SEL>, - <&topckgen CLK_TOP_XTAL>; - clock-names = "cpu", "intermediate"; - operating-points-v2 = <&cluster0_opp>; - mediatek,cci = <&cci>; - }; - - cluster0_opp: opp_table0 { - compatible = "operating-points-v2"; - opp-shared; - - opp00 { - opp-hz = /bits/ 64 <800000000>; - opp-microvolt = <850000>; - }; - - opp01 { - opp-hz = /bits/ 64 <1100000000>; - opp-microvolt = <850000>; - }; - - opp02 { - opp-hz = /bits/ 64 <1500000000>; - opp-microvolt = <850000>; - }; - - opp03 { - opp-hz = /bits/ 64 <1800000000>; - opp-microvolt = <900000>; - }; - }; - }; - - cci_opp: opp_table_cci { - compatible = "operating-points-v2"; - opp-shared; - - opp00 { - opp-hz = /bits/ 64 <480000000>; - opp-microvolt = <850000>; - }; - - opp01 { - opp-hz = /bits/ 64 <660000000>; - opp-microvolt = <850000>; - }; - - opp02 { - opp-hz = /bits/ 64 <900000000>; - opp-microvolt = <850000>; - }; - - opp03 { - opp-hz = /bits/ 64 <1080000000>; - opp-microvolt = <900000>; - }; - }; - - clk40m: oscillator@0 { - compatible = "fixed-clock"; - clock-frequency = <40000000>; - #clock-cells = <0>; - clock-output-names = "clkxtal"; - }; - - pmu { - compatible = "arm,cortex-a73-pmu"; - interrupt-parent = <&gic>; - interrupt = ; - }; - - psci { - compatible = "arm,psci-0.2"; - method = "smc"; - }; - - reg_1p8v: regulator-1p8v { - compatible = "regulator-fixed"; - regulator-name = "fixed-1.8V"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-boot-on; - regulator-always-on; - }; - - reg_3p3v: regulator-3p3v { - compatible = "regulator-fixed"; - regulator-name = "fixed-3.3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; - }; - - reserved-memory { - ranges; - #address-cells = <2>; - #size-cells = <2>; - - /* 320 KiB reserved for ARM Trusted Firmware (BL31 and BL32) */ - secmon_reserved: secmon@43000000 { - reg = <0 0x43000000 0 0x50000>; - no-map; - }; - }; - - soc { - compatible = "simple-bus"; - ranges; - #address-cells = <2>; - #size-cells = <2>; - - gic: interrupt-controller@c000000 { - compatible = "arm,gic-v3"; - reg = <0 0x0c000000 0 0x40000>, /* GICD */ - <0 0x0c080000 0 0x200000>, /* GICR */ - <0 0x0c400000 0 0x2000>, /* GICC */ - <0 0x0c410000 0 0x1000>, /* GICH */ - <0 0x0c420000 0 0x2000>; /* GICV */ - interrupt-parent = <&gic>; - interrupts = ; - interrupt-controller; - #interrupt-cells = <3>; - }; - - phyfw: phy-firmware@f000000 { - compatible = "mediatek,2p5gphy-fw"; - reg = <0 0x0f000000 0 0x8000>, - <0 0x0f100000 0 0x20000>, - <0 0x0f0f0000 0 0x200>; - }; - - infracfg: infracfg@10001000 { - compatible = "mediatek,mt7988-infracfg", "syscon"; - reg = <0 0x10001000 0 0x1000>; - #clock-cells = <1>; - }; - - topckgen: topckgen@1001b000 { - compatible = "mediatek,mt7988-topckgen", "syscon"; - reg = <0 0x1001b000 0 0x1000>; - #clock-cells = <1>; - }; - - watchdog: watchdog@1001c000 { - compatible = "mediatek,mt7988-wdt", - "mediatek,mt6589-wdt", - "syscon"; - reg = <0 0x1001c000 0 0x1000>; - interrupts = ; - #reset-cells = <1>; - }; - - apmixedsys: apmixedsys@1001e000 { - compatible = "mediatek,mt7988-apmixedsys"; - reg = <0 0x1001e000 0 0x1000>; - #clock-cells = <1>; - }; - - pio: pinctrl@1001f000 { - compatible = "mediatek,mt7988-pinctrl", "syscon"; - reg = <0 0x1001f000 0 0x1000>, - <0 0x11c10000 0 0x1000>, - <0 0x11d00000 0 0x1000>, - <0 0x11d20000 0 0x1000>, - <0 0x11e00000 0 0x1000>, - <0 0x11f00000 0 0x1000>, - <0 0x1000b000 0 0x1000>; - reg-names = "gpio_base", "iocfg_tr_base", - "iocfg_br_base", "iocfg_rb_base", - "iocfg_lb_base", "iocfg_tl_base", "eint"; - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pio 0 0 84>; - interrupt-controller; - interrupts = ; - interrupt-parent = <&gic>; - #interrupt-cells = <2>; - - mdio0_pins: mdio0-pins { - mux { - function = "eth"; - groups = "mdc_mdio0"; - }; - - conf { - groups = "mdc_mdio0"; - drive-strength = ; - }; - }; - - i2c0_pins: i2c0-pins-g0 { - mux { - function = "i2c"; - groups = "i2c0_1"; - }; - }; - - i2c1_pins: i2c1-pins-g0 { - mux { - function = "i2c"; - groups = "i2c1_0"; - }; - }; - - i2c1_sfp_pins: i2c1-sfp-pins-g0 { - mux { - function = "i2c"; - groups = "i2c1_sfp"; - }; - }; - - i2c2_pins: i2c2-pins { - mux { - function = "i2c"; - groups = "i2c2"; - }; - }; - - i2c2_0_pins: i2c2-pins-g0 { - mux { - function = "i2c"; - groups = "i2c2_0"; - }; - }; - - i2c2_1_pins: i2c2-pins-g1 { - mux { - function = "i2c"; - groups = "i2c2_1"; - }; - }; - - gbe0_led0_pins: gbe0-led0-pins { - mux { - function = "led"; - groups = "gbe0_led0"; - }; - }; - - gbe1_led0_pins: gbe1-led0-pins { - mux { - function = "led"; - groups = "gbe1_led0"; - }; - }; - - gbe2_led0_pins: gbe2-led0-pins { - mux { - function = "led"; - groups = "gbe2_led0"; - }; - }; - - gbe3_led0_pins: gbe3-led0-pins { - mux { - function = "led"; - groups = "gbe3_led0"; - }; - }; - - gbe0_led1_pins: gbe0-led1-pins { - mux { - function = "led"; - groups = "gbe0_led1"; - }; - }; - - gbe1_led1_pins: gbe1-led1-pins { - mux { - function = "led"; - groups = "gbe1_led1"; - }; - }; - - gbe2_led1_pins: gbe2-led1-pins { - mux { - function = "led"; - groups = "gbe2_led1"; - }; - }; - - gbe3_led1_pins: gbe3-led1-pins { - mux { - function = "led"; - groups = "gbe3_led1"; - }; - }; - - i2p5gbe_led0_pins: 2p5gbe-led0-pins { - mux { - function = "led"; - groups = "2p5gbe_led0"; - }; - }; - - i2p5gbe_led1_pins: 2p5gbe-led1-pins { - mux { - function = "led"; - groups = "2p5gbe_led1"; - }; - }; - - mmc0_pins_emmc_45: mmc0-pins-emmc-45 { - mux { - function = "flash"; - groups = "emmc_45"; - }; - }; - - mmc0_pins_emmc_51: mmc0-pins-emmc-51 { - mux { - function = "flash"; - groups = "emmc_51"; - }; - }; - - mmc0_pins_sdcard: mmc0-pins-sdcard { - mux { - function = "flash"; - groups = "sdcard"; - }; - }; - - uart0_pins: uart0-pins { - mux { - function = "uart"; - groups = "uart0"; - }; - }; - - snfi_pins: snfi-pins { - mux { - function = "flash"; - groups = "snfi"; - }; - }; - - spi0_pins: spi0-pins { - mux { - function = "spi"; - groups = "spi0"; - }; - }; - - spi0_flash_pins: spi0-flash-pins { - mux { - function = "spi"; - groups = "spi0", "spi0_wp_hold"; - }; - }; - - spi1_pins: spi1-pins { - mux { - function = "spi"; - groups = "spi1"; - }; - }; - - spi2_pins: spi2-pins { - mux { - function = "spi"; - groups = "spi2"; - }; - }; - - spi2_flash_pins: spi2-flash-pins { - mux { - function = "spi"; - groups = "spi2", "spi2_wp_hold"; - }; - }; - - pcie0_pins: pcie0-pins { - mux { - function = "pcie"; - groups = "pcie_2l_0_pereset", "pcie_clk_req_n0_0", - "pcie_wake_n0_0"; - }; - }; - - pcie1_pins: pcie1-pins { - mux { - function = "pcie"; - groups = "pcie_2l_1_pereset", "pcie_clk_req_n1", - "pcie_wake_n1_0"; - }; - }; - - pcie2_pins: pcie2-pins { - mux { - function = "pcie"; - groups = "pcie_1l_0_pereset", "pcie_clk_req_n2_0", - "pcie_wake_n2_0"; - }; - }; - - pcie3_pins: pcie3-pins { - mux { - function = "pcie"; - groups = "pcie_1l_1_pereset", "pcie_clk_req_n3", - "pcie_wake_n3_0"; - }; - }; - }; - - pwm: pwm@10048000 { - compatible = "mediatek,mt7988-pwm"; - reg = <0 0x10048000 0 0x1000>; - #pwm-cells = <2>; - clocks = <&infracfg CLK_INFRA_66M_PWM_BCK>, - <&infracfg CLK_INFRA_66M_PWM_HCK>, - <&infracfg CLK_INFRA_66M_PWM_CK1>, - <&infracfg CLK_INFRA_66M_PWM_CK2>, - <&infracfg CLK_INFRA_66M_PWM_CK3>, - <&infracfg CLK_INFRA_66M_PWM_CK4>, - <&infracfg CLK_INFRA_66M_PWM_CK5>, - <&infracfg CLK_INFRA_66M_PWM_CK6>, - <&infracfg CLK_INFRA_66M_PWM_CK7>, - <&infracfg CLK_INFRA_66M_PWM_CK8>; - clock-names = "top", "main", "pwm1", "pwm2", "pwm3", - "pwm4","pwm5","pwm6","pwm7","pwm8"; - status = "disabled"; - }; - - sgmiisys0: syscon@10060000 { - compatible = "mediatek,mt7988-sgmiisys", - "mediatek,mt7988-sgmiisys_0", - "syscon"; - reg = <0 0x10060000 0 0x1000>; - #clock-cells = <1>; - }; - - sgmiisys1: syscon@10070000 { - compatible = "mediatek,mt7988-sgmiisys", - "mediatek,mt7988-sgmiisys_1", - "syscon"; - reg = <0 0x10070000 0 0x1000>; - #clock-cells = <1>; - }; - - usxgmiisys0: usxgmiisys@10080000 { - compatible = "mediatek,mt7988-usxgmiisys", - "mediatek,mt7988-usxgmiisys_0", - "syscon"; - reg = <0 0x10080000 0 0x1000>; - #clock-cells = <1>; - }; - - usxgmiisys1: usxgmiisys@10081000 { - compatible = "mediatek,mt7988-usxgmiisys", - "mediatek,mt7988-usxgmiisys_1", - "syscon"; - reg = <0 0x10081000 0 0x1000>; - #clock-cells = <1>; - }; - - mcusys: mcusys@100e0000 { - compatible = "mediatek,mt7988-mcusys", "syscon"; - reg = <0 0x100e0000 0 0x1000>; - #clock-cells = <1>; - }; - - uart0: serial@11000000 { - compatible = "mediatek,mt7986-uart", - "mediatek,mt6577-uart"; - reg = <0 0x11000000 0 0x100>; - interrupts = ; - /* - * 8250-mtk driver don't control "baud" clock since commit - * e32a83c70cf9 (kernel v5.7), but both "baud" and "bus" clocks - * still need to be passed to the driver to prevent probe fail - */ - clocks = <&topckgen CLK_TOP_UART_SEL>, - <&infracfg CLK_INFRA_52M_UART0_CK>; - clock-names = "baud", "bus"; - assigned-clocks = <&topckgen CLK_TOP_UART_SEL>, - <&infracfg CLK_INFRA_MUX_UART0_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_XTAL>, - <&topckgen CLK_TOP_UART_SEL>; - pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins>; - status = "disabled"; - }; - - snand: spi@11001000 { - compatible = "mediatek,mt7986-snand"; - reg = <0 0x11001000 0 0x1000>; - interrupts = ; - clocks = <&infracfg CLK_INFRA_SPINFI>, - <&infracfg CLK_INFRA_NFI>; - clock-names = "pad_clk", "nfi_clk"; - assigned-clocks = <&topckgen CLK_TOP_SPINFI_SEL>, - <&topckgen CLK_TOP_NFI1X_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_MPLL_D8>, - <&topckgen CLK_TOP_MPLL_D8>; - nand-ecc-engine = <&bch>; - mediatek,quad-spi; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&snfi_pins>; - status = "disabled"; - }; - - bch: ecc@11002000 { - compatible = "mediatek,mt7686-ecc"; - reg = <0 0x11002000 0 0x1000>; - interrupts = ; - clocks = <&topckgen CLK_TOP_NFI1X_SEL>; - clock-names = "nfiecc_clk"; - status = "disabled"; - }; - - i2c0: i2c@11003000 { - compatible = "mediatek,mt7988-i2c", - "mediatek,mt7981-i2c"; - reg = <0 0x11003000 0 0x1000>, - <0 0x10217080 0 0x80>; - interrupts = ; - clock-div = <1>; - clocks = <&infracfg CLK_INFRA_I2C_BCK>, - <&infracfg CLK_INFRA_66M_AP_DMA_BCK>; - clock-names = "main", "dma"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - i2c1: i2c@11004000 { - compatible = "mediatek,mt7988-i2c", - "mediatek,mt7981-i2c"; - reg = <0 0x11004000 0 0x1000>, - <0 0x10217100 0 0x80>; - interrupts = ; - clock-div = <1>; - clocks = <&infracfg CLK_INFRA_I2C_BCK>, - <&infracfg CLK_INFRA_66M_AP_DMA_BCK>; - clock-names = "main", "dma"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - i2c2: i2c@11005000 { - compatible = "mediatek,mt7988-i2c", - "mediatek,mt7981-i2c"; - reg = <0 0x11005000 0 0x1000>, - <0 0x10217180 0 0x80>; - interrupts = ; - clock-div = <1>; - clocks = <&infracfg CLK_INFRA_I2C_BCK>, - <&infracfg CLK_INFRA_66M_AP_DMA_BCK>; - clock-names = "main", "dma"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - spi0: spi@11007000 { - compatible = "mediatek,ipm-spi-quad", "mediatek,spi-ipm"; - reg = <0 0x11007000 0 0x100>; - interrupts = ; - clocks = <&topckgen CLK_TOP_MPLL_D2>, - <&topckgen CLK_TOP_SPI_SEL>, - <&infracfg CLK_INFRA_104M_SPI0>, - <&infracfg CLK_INFRA_66M_SPI0_HCK>; - clock-names = "parent-clk", "sel-clk", "spi-clk", - "spi-hclk"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - spi1: spi@11008000 { - compatible = "mediatek,ipm-spi-single", "mediatek,spi-ipm"; - reg = <0 0x11008000 0 0x100>; - interrupts = ; - clocks = <&topckgen CLK_TOP_MPLL_D2>, - <&topckgen CLK_TOP_SPI_SEL>, - <&infracfg CLK_INFRA_104M_SPI1>, - <&infracfg CLK_INFRA_66M_SPI1_HCK>; - clock-names = "parent-clk", "sel-clk", "spi-clk", - "spi-hclk"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&spi1_pins>; - status = "disabled"; - }; - - spi2: spi@11009000 { - compatible = "mediatek,ipm-spi-quad", "mediatek,spi-ipm"; - reg = <0 0x11009000 0 0x100>; - interrupts = ; - clocks = <&topckgen CLK_TOP_MPLL_D2>, - <&topckgen CLK_TOP_SPI_SEL>, - <&infracfg CLK_INFRA_104M_SPI2_BCK>, - <&infracfg CLK_INFRA_66M_SPI2_HCK>; - clock-names = "parent-clk", "sel-clk", "spi-clk", - "spi-hclk"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - fan: pwm-fan { - compatible = "pwm-fan"; - /* cooling level (0, 1, 2) : (0% duty, 50% duty, 100% duty) */ - cooling-levels = <0 128 255>; - #cooling-cells = <2>; - #thermal-sensor-cells = <1>; - status = "disabled"; - }; - - lvts: lvts@1100a000 { - compatible = "mediatek,mt7988-lvts"; - reg = <0 0x1100a000 0 0x1000>; - clocks = <&infracfg CLK_INFRA_26M_THERM_SYSTEM>; - clock-names = "lvts_clk"; - nvmem-cells = <&lvts_calibration>; - nvmem-cell-names = "e_data1"; - #thermal-sensor-cells = <1>; - }; - - ssusb0: usb@11190000 { - compatible = "mediatek,mt7988-xhci", - "mediatek,mtk-xhci"; - reg = <0 0x11190000 0 0x2e00>, - <0 0x11193e00 0 0x0100>; - reg-names = "mac", "ippc"; - interrupts = ; - phys = <&xphyu2port0 PHY_TYPE_USB2>, - <&xphyu3port0 PHY_TYPE_USB3>; - clocks = <&infracfg CLK_INFRA_USB_SYS>, - <&infracfg CLK_INFRA_USB_XHCI>, - <&infracfg CLK_INFRA_USB_REF>, - <&infracfg CLK_INFRA_66M_USB_HCK>, - <&infracfg CLK_INFRA_133M_USB_HCK>; - clock-names = "sys_ck", - "xhci_ck", - "ref_ck", - "mcu_ck", - "dma_ck"; - #address-cells = <2>; - #size-cells = <2>; - mediatek,p0_speed_fixup; - status = "disabled"; - }; - - ssusb1: usb@11200000 { - compatible = "mediatek,mt7988-xhci", - "mediatek,mtk-xhci"; - reg = <0 0x11200000 0 0x2e00>, - <0 0x11203e00 0 0x0100>; - reg-names = "mac", "ippc"; - interrupts = ; - phys = <&tphyu2port0 PHY_TYPE_USB2>, - <&tphyu3port0 PHY_TYPE_USB3>; - clocks = <&infracfg CLK_INFRA_USB_SYS_CK_P1>, - <&infracfg CLK_INFRA_USB_XHCI_CK_P1>, - <&infracfg CLK_INFRA_USB_CK_P1>, - <&infracfg CLK_INFRA_66M_USB_HCK_CK_P1>, - <&infracfg CLK_INFRA_133M_USB_HCK_CK_P1>; - clock-names = "sys_ck", - "xhci_ck", - "ref_ck", - "mcu_ck", - "dma_ck"; - #address-cells = <2>; - #size-cells = <2>; - status = "disabled"; - }; - - afe: audio-controller@11210000 { - compatible = "mediatek,mt79xx-audio"; - reg = <0 0x11210000 0 0x9000>; - interrupts = ; - clocks = <&infracfg CLK_INFRA_66M_AUD_SLV_BCK>, - <&infracfg CLK_INFRA_AUD_26M>, - <&infracfg CLK_INFRA_AUD_L>, - <&infracfg CLK_INFRA_AUD_AUD>, - <&infracfg CLK_INFRA_AUD_EG2>, - <&topckgen CLK_TOP_AUD_SEL>, - <&topckgen CLK_TOP_AUD_I2S_M>; - clock-names = "aud_bus_ck", - "aud_26m_ck", - "aud_l_ck", - "aud_aud_ck", - "aud_eg2_ck", - "aud_sel", - "aud_i2s_m"; - assigned-clocks = <&topckgen CLK_TOP_AUD_SEL>, - <&topckgen CLK_TOP_A1SYS_SEL>, - <&topckgen CLK_TOP_AUD_L_SEL>, - <&topckgen CLK_TOP_A_TUNER_SEL>; - assigned-clock-parents = <&apmixedsys CLK_APMIXED_APLL2>, - <&topckgen CLK_TOP_APLL2_D4>, - <&apmixedsys CLK_APMIXED_APLL2>, - <&topckgen CLK_TOP_APLL2_D4>; - status = "disabled"; - }; - - mmc0: mmc@11230000 { - compatible = "mediatek,mt7986-mmc", - "mediatek,mt7981-mmc"; - reg = <0 0x11230000 0 0x1000>, - <0 0x11D60000 0 0x1000>; - interrupts = ; - clocks = <&infracfg CLK_INFRA_MSDC400>, - <&infracfg CLK_INFRA_MSDC2_HCK>, - <&infracfg CLK_INFRA_66M_MSDC_0_HCK>, - <&infracfg CLK_INFRA_133M_MSDC_0_HCK>; - assigned-clocks = <&topckgen CLK_TOP_EMMC_250M_SEL>, - <&topckgen CLK_TOP_EMMC_400M_SEL>; - assigned-clock-parents = <&topckgen CLK_TOP_NET1PLL_D5_D2>, - <&apmixedsys CLK_APMIXED_MSDCPLL>; - clock-names = "source", - "hclk", - "axi_cg", - "ahb_cg"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - pcie2: pcie@11280000 { - compatible = "mediatek,mt7988-pcie", - "mediatek,mt7986-pcie", - "mediatek,mt8192-pcie"; - reg = <0 0x11280000 0 0x2000>; - reg-names = "pcie-mac"; - ranges = <0x81000000 0x00 0x20000000 0x00 - 0x20000000 0x00 0x00200000>, - <0x82000000 0x00 0x20200000 0x00 - 0x20200000 0x00 0x07e00000>; - device_type = "pci"; - linux,pci-domain = <3>; - interrupts = ; - bus-range = <0x00 0xff>; - clocks = <&infracfg CLK_INFRA_PCIE_PIPE_P2>, - <&infracfg CLK_INFRA_PCIE_GFMUX_TL_P2>, - <&infracfg CLK_INFRA_PCIE_PERI_26M_CK_P2>, - <&infracfg CLK_INFRA_133M_PCIE_CK_P2>; - clock-names = "pl_250m", "tl_26m", "peri_26m", - "top_133m"; - pinctrl-names = "default"; - pinctrl-0 = <&pcie2_pins>; - phys = <&xphyu3port0 PHY_TYPE_PCIE>; - phy-names = "pcie-phy"; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0x7>; - interrupt-map = <0 0 0 1 &pcie_intc2 0>, - <0 0 0 2 &pcie_intc2 1>, - <0 0 0 3 &pcie_intc2 2>, - <0 0 0 4 &pcie_intc2 3>; - #address-cells = <3>; - #size-cells = <2>; - status = "disabled"; - - pcie_intc2: interrupt-controller { - #address-cells = <0>; - #interrupt-cells = <1>; - interrupt-controller; - }; - }; - - pcie3: pcie@11290000 { - compatible = "mediatek,mt7988-pcie", - "mediatek,mt7986-pcie", - "mediatek,mt8192-pcie"; - reg = <0 0x11290000 0 0x2000>; - reg-names = "pcie-mac"; - ranges = <0x81000000 0x00 0x28000000 0x00 - 0x28000000 0x00 0x00200000>, - <0x82000000 0x00 0x28200000 0x00 - 0x28200000 0x00 0x07e00000>; - device_type = "pci"; - linux,pci-domain = <2>; - interrupts = ; - bus-range = <0x00 0xff>; - clocks = <&infracfg CLK_INFRA_PCIE_PIPE_P3>, - <&infracfg CLK_INFRA_PCIE_GFMUX_TL_P3>, - <&infracfg CLK_INFRA_PCIE_PERI_26M_CK_P3>, - <&infracfg CLK_INFRA_133M_PCIE_CK_P3>; - clock-names = "pl_250m", "tl_26m", "peri_26m", - "top_133m"; - pinctrl-names = "default"; - pinctrl-0 = <&pcie3_pins>; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0x7>; - interrupt-map = <0 0 0 1 &pcie_intc3 0>, - <0 0 0 2 &pcie_intc3 1>, - <0 0 0 3 &pcie_intc3 2>, - <0 0 0 4 &pcie_intc3 3>; - #address-cells = <3>; - #size-cells = <2>; - status = "disabled"; - - pcie_intc3: interrupt-controller { - #address-cells = <0>; - #interrupt-cells = <1>; - interrupt-controller; - }; - }; - - pcie0: pcie@11300000 { - compatible = "mediatek,mt7988-pcie", - "mediatek,mt7986-pcie", - "mediatek,mt8192-pcie"; - reg = <0 0x11300000 0 0x2000>; - reg-names = "pcie-mac"; - ranges = <0x81000000 0x00 0x30000000 0x00 - 0x30000000 0x00 0x00200000>, - <0x82000000 0x00 0x30200000 0x00 - 0x30200000 0x00 0x07e00000>; - device_type = "pci"; - linux,pci-domain = <0>; - interrupts = ; - bus-range = <0x00 0xff>; - clocks = <&infracfg CLK_INFRA_PCIE_PIPE_P0>, - <&infracfg CLK_INFRA_PCIE_GFMUX_TL_P0>, - <&infracfg CLK_INFRA_PCIE_PERI_26M_CK_P0>, - <&infracfg CLK_INFRA_133M_PCIE_CK_P0>; - clock-names = "pl_250m", "tl_26m", "peri_26m", - "top_133m"; - pinctrl-names = "default"; - pinctrl-0 = <&pcie0_pins>; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0x7>; - interrupt-map = <0 0 0 1 &pcie_intc0 0>, - <0 0 0 2 &pcie_intc0 1>, - <0 0 0 3 &pcie_intc0 2>, - <0 0 0 4 &pcie_intc0 3>; - #address-cells = <3>; - #size-cells = <2>; - status = "disabled"; - - pcie_intc0: interrupt-controller { - #address-cells = <0>; - #interrupt-cells = <1>; - interrupt-controller; - }; - }; - - pcie1: pcie@11310000 { - compatible = "mediatek,mt7988-pcie", - "mediatek,mt7986-pcie", - "mediatek,mt8192-pcie"; - reg = <0 0x11310000 0 0x2000>; - reg-names = "pcie-mac"; - ranges = <0x81000000 0x00 0x38000000 0x00 - 0x38000000 0x00 0x00200000>, - <0x82000000 0x00 0x38200000 0x00 - 0x38200000 0x00 0x07e00000>; - device_type = "pci"; - linux,pci-domain = <1>; - interrupts = ; - bus-range = <0x00 0xff>; - clocks = <&infracfg CLK_INFRA_PCIE_PIPE_P1>, - <&infracfg CLK_INFRA_PCIE_GFMUX_TL_P1>, - <&infracfg CLK_INFRA_PCIE_PERI_26M_CK_P1>, - <&infracfg CLK_INFRA_133M_PCIE_CK_P1>; - clock-names = "pl_250m", "tl_26m", "peri_26m", - "top_133m"; - pinctrl-names = "default"; - pinctrl-0 = <&pcie1_pins>; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0x7>; - interrupt-map = <0 0 0 1 &pcie_intc1 0>, - <0 0 0 2 &pcie_intc1 1>, - <0 0 0 3 &pcie_intc1 2>, - <0 0 0 4 &pcie_intc1 3>; - #address-cells = <3>; - #size-cells = <2>; - status = "disabled"; - - pcie_intc1: interrupt-controller { - #address-cells = <0>; - #interrupt-cells = <1>; - interrupt-controller; - }; - }; - - tphy: tphy@11c50000 { - compatible = "mediatek,mt7988", - "mediatek,generic-tphy-v2"; - ranges; - #address-cells = <2>; - #size-cells = <2>; - status = "disabled"; - - tphyu2port0: usb-phy@11c50000 { - reg = <0 0x11c50000 0 0x700>; - clocks = <&infracfg CLK_INFRA_USB_UTMI_CK_P1>; - clock-names = "ref"; - #phy-cells = <1>; - }; - - tphyu3port0: usb-phy@11c50700 { - reg = <0 0x11c50700 0 0x900>; - clocks = <&infracfg CLK_INFRA_USB_PIPE_CK_P1>; - clock-names = "ref"; - #phy-cells = <1>; - mediatek,usb3-pll-ssc-delta; - mediatek,usb3-pll-ssc-delta1; - }; - }; - - topmisc: topmisc@11d10000 { - compatible = "mediatek,mt7988-topmisc", "syscon", - "mediatek,mt7988-power-controller"; - reg = <0 0x11d10000 0 0x10000>; - #clock-cells = <1>; - #power-domain-cells = <1>; - #address-cells = <1>; - #size-cells = <0>; - }; - - xphy: xphy@11e10000 { - compatible = "mediatek,mt7988", - "mediatek,xsphy"; - ranges; - #address-cells = <2>; - #size-cells = <2>; - status = "disabled"; - - xphyu2port0: usb-phy@11e10000 { - reg = <0 0x11e10000 0 0x400>; - clocks = <&infracfg CLK_INFRA_USB_UTMI>; - clock-names = "ref"; - #phy-cells = <1>; - }; - - xphyu3port0: usb-phy@11e13000 { - reg = <0 0x11e13400 0 0x500>; - clocks = <&infracfg CLK_INFRA_USB_PIPE>; - clock-names = "ref"; - #phy-cells = <1>; - mediatek,syscon-type = <&topmisc 0x218 0>; - }; - }; - - xfi_pextp0: xfi-pextp@11f20000 { - compatible = "mediatek,mt7988-xfi-pextp", - "mediatek,mt7988-xfi-pextp_0", - "syscon"; - reg = <0 0x11f20000 0 0x10000>; - #clock-cells = <1>; - }; - - xfi_pextp1: xfi-pextp@11f30000 { - compatible = "mediatek,mt7988-xfi-pextp", - "mediatek,mt7988-xfi-pextp_1", - "syscon"; - reg = <0 0x11f30000 0 0x10000>; - #clock-cells = <1>; - }; - - xfi_pll: xfi-pll@11f40000 { - compatible = "mediatek,mt7988-xfi-pll", "syscon"; - reg = <0 0x11f40000 0 0x1000>; - #clock-cells = <1>; - }; - - efuse: efuse@11f50000 { - compatible = "mediatek,efuse"; - reg = <0 0x11f50000 0 0x1000>; - #address-cells = <1>; - #size-cells = <1>; - - lvts_calibration: calib@918 { - reg = <0x918 0x28>; - }; - - phy_calibration_p0: calib@940 { - reg = <0x940 0x10>; - }; - - phy_calibration_p1: calib@954 { - reg = <0x954 0x10>; - }; - - phy_calibration_p2: calib@968 { - reg = <0x968 0x10>; - }; - - phy_calibration_p3: calib@97c { - reg = <0x97c 0x10>; - }; - - cpufreq_calibration: calib@278 { - reg = <0x278 0x1>; - }; - }; - - ethsys: syscon@15000000 { - compatible = "mediatek,mt7988-ethsys", "syscon"; - reg = <0 0x15000000 0 0x1000>; - #clock-cells = <1>; - #reset-cells = <1>; - #address-cells = <1>; - #size-cells = <1>; - }; - - switch: switch@15020000 { - compatible = "mediatek,mt7988-switch"; - reg = <0 0x15020000 0 0x8000>; - interrupt-controller; - #interrupt-cells = <1>; - interrupt-parent = <&gic>; - interrupts = ; - resets = <ðrst 0>; - #address-cells = <1>; - #size-cells = <1>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - label = "lan0"; - phy-mode = "internal"; - phy-handle = <&gsw_phy0>; - }; - - port@1 { - reg = <1>; - label = "lan1"; - phy-mode = "internal"; - phy-handle = <&gsw_phy1>; - }; - - port@2 { - reg = <2>; - label = "lan2"; - phy-mode = "internal"; - phy-handle = <&gsw_phy2>; - }; - - port@3 { - reg = <3>; - label = "lan3"; - phy-mode = "internal"; - phy-handle = <&gsw_phy3>; - }; - - port@6 { - reg = <6>; - ethernet = <&gmac0>; - phy-mode = "internal"; - - fixed-link { - speed = <10000>; - full-duplex; - pause; - }; - }; - }; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - mediatek,pio = <&pio>; - - gsw_phy0: ethernet-phy@0 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <0>; - phy-mode = "internal"; - nvmem-cells = <&phy_calibration_p0>; - nvmem-cell-names = "phy-cal-data"; - - leds { - #address-cells = <1>; - #size-cells = <0>; - - gsw_phy0_led0: gsw-phy0-led0@0 { - reg = <0>; - function = LED_FUNCTION_LAN; - status = "disabled"; - }; - - gsw_phy0_led1: gsw-phy0-led1@1 { - reg = <1>; - function = LED_FUNCTION_LAN; - status = "disabled"; - }; - }; - }; - - gsw_phy1: ethernet-phy@1 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <1>; - phy-mode = "internal"; - nvmem-cells = <&phy_calibration_p1>; - nvmem-cell-names = "phy-cal-data"; - - leds { - #address-cells = <1>; - #size-cells = <0>; - - gsw_phy1_led0: gsw-phy1-led0@0 { - reg = <0>; - function = LED_FUNCTION_LAN; - status = "disabled"; - }; - - gsw_phy1_led1: gsw-phy1-led1@1 { - reg = <1>; - function = LED_FUNCTION_LAN; - status = "disabled"; - }; - }; - }; - - gsw_phy2: ethernet-phy@2 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <2>; - phy-mode = "internal"; - nvmem-cells = <&phy_calibration_p2>; - nvmem-cell-names = "phy-cal-data"; - - leds { - #address-cells = <1>; - #size-cells = <0>; - - gsw_phy2_led0: gsw-phy2-led0@0 { - reg = <0>; - function = LED_FUNCTION_LAN; - status = "disabled"; - }; - - gsw_phy2_led1: gsw-phy2-led1@1 { - reg = <1>; - function = LED_FUNCTION_LAN; - status = "disabled"; - }; - }; - }; - - gsw_phy3: ethernet-phy@3 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <3>; - phy-mode = "internal"; - nvmem-cells = <&phy_calibration_p3>; - nvmem-cell-names = "phy-cal-data"; - - leds { - #address-cells = <1>; - #size-cells = <0>; - - gsw_phy3_led0: gsw-phy3-led0@0 { - reg = <0>; - function = LED_FUNCTION_LAN; - status = "disabled"; - }; - - gsw_phy3_led1: gsw-phy3-led1@1 { - reg = <1>; - function = LED_FUNCTION_LAN; - status = "disabled"; - }; - }; - }; - }; - }; - - ethwarp: syscon@15031000 { - compatible = "mediatek,mt7988-ethwarp", "syscon", "simple-mfd"; - reg = <0 0x15031000 0 0x1000>; - #clock-cells = <1>; - - ethrst: reset-controller { - compatible = "ti,syscon-reset"; - #reset-cells = <1>; - ti,reset-bits = < - 0x8 9 0x8 9 0 0 (ASSERT_SET | DEASSERT_CLEAR | STATUS_NONE) - >; - }; - }; - - eth: ethernet@15100000 { - compatible = "mediatek,mt7988-eth"; - reg = <0 0x15100000 0 0x80000>, - <0 0x15400000 0 0x380000>; - interrupts = , - , - , - ; - clocks = <ðsys CLK_ETHDMA_XGP1_EN>, - <ðsys CLK_ETHDMA_XGP2_EN>, - <ðsys CLK_ETHDMA_XGP3_EN>, - <ðsys CLK_ETHDMA_FE_EN>, - <ðsys CLK_ETHDMA_GP2_EN>, - <ðsys CLK_ETHDMA_GP1_EN>, - <ðsys CLK_ETHDMA_GP3_EN>, - <ðsys CLK_ETHDMA_ESW_EN>, - <ðsys CLK_ETHDMA_CRYPT0_EN>, - <&sgmiisys0 CLK_SGM0_TX_EN>, - <&sgmiisys0 CLK_SGM0_RX_EN>, - <&sgmiisys1 CLK_SGM1_TX_EN>, - <&sgmiisys1 CLK_SGM1_RX_EN>, - <ðwarp CLK_ETHWARP_WOCPU2_EN>, - <ðwarp CLK_ETHWARP_WOCPU1_EN>, - <ðwarp CLK_ETHWARP_WOCPU0_EN>, - <&topckgen CLK_TOP_USXGMII_SBUS_0_SEL>, - <&topckgen CLK_TOP_USXGMII_SBUS_1_SEL>, - <&topckgen CLK_TOP_SGM_0_SEL>, - <&topckgen CLK_TOP_SGM_1_SEL>, - <&topckgen CLK_TOP_XFI_PHY_0_XTAL_SEL>, - <&topckgen CLK_TOP_XFI_PHY_1_XTAL_SEL>, - <&topckgen CLK_TOP_ETH_GMII_SEL>, - <&topckgen CLK_TOP_ETH_REFCK_50M_SEL>, - <&topckgen CLK_TOP_ETH_SYS_200M_SEL>, - <&topckgen CLK_TOP_ETH_SYS_SEL>, - <&topckgen CLK_TOP_ETH_XGMII_SEL>, - <&topckgen CLK_TOP_ETH_MII_SEL>, - <&topckgen CLK_TOP_NETSYS_SEL>, - <&topckgen CLK_TOP_NETSYS_500M_SEL>, - <&topckgen CLK_TOP_NETSYS_PAO_2X_SEL>, - <&topckgen CLK_TOP_NETSYS_SYNC_250M_SEL>, - <&topckgen CLK_TOP_NETSYS_PPEFB_250M_SEL>, - <&topckgen CLK_TOP_NETSYS_WARP_SEL>; - clock-names = "xgp1", "xgp2", "xgp3", "fe", "gp2", "gp1", - "gp3", "esw", "crypto", "sgmii_tx250m", - "sgmii_rx250m", "sgmii2_tx250m", "sgmii2_rx250m", - "ethwarp_wocpu2", "ethwarp_wocpu1", - "ethwarp_wocpu0", "top_usxgmii0_sel", - "top_usxgmii1_sel", "top_sgm0_sel", - "top_sgm1_sel", "top_xfi_phy0_xtal_sel", - "top_xfi_phy1_xtal_sel", "top_eth_gmii_sel", - "top_eth_refck_50m_sel", "top_eth_sys_200m_sel", - "top_eth_sys_sel", "top_eth_xgmii_sel", - "top_eth_mii_sel", "top_netsys_sel", - "top_netsys_500m_sel", "top_netsys_pao_2x_sel", - "top_netsys_sync_250m_sel", - "top_netsys_ppefb_250m_sel", - "top_netsys_warp_sel"; - assigned-clocks = <&topckgen CLK_TOP_NETSYS_2X_SEL>, - <&topckgen CLK_TOP_NETSYS_GSW_SEL>, - <&topckgen CLK_TOP_USXGMII_SBUS_0_SEL>, - <&topckgen CLK_TOP_USXGMII_SBUS_1_SEL>, - <&topckgen CLK_TOP_SGM_0_SEL>, - <&topckgen CLK_TOP_SGM_1_SEL>; - assigned-clock-parents = <&apmixedsys CLK_APMIXED_NET2PLL>, - <&topckgen CLK_TOP_NET1PLL_D4>, - <&topckgen CLK_TOP_NET1PLL_D8_D4>, - <&topckgen CLK_TOP_NET1PLL_D8_D4>, - <&apmixedsys CLK_APMIXED_SGMPLL>, - <&apmixedsys CLK_APMIXED_SGMPLL>; - mediatek,ethsys = <ðsys>; - mediatek,sgmiisys = <&sgmiisys0>, <&sgmiisys1>; - mediatek,usxgmiisys = <&usxgmiisys0>, <&usxgmiisys1>; - mediatek,xfi-pextp = <&xfi_pextp0>, <&xfi_pextp1>; - mediatek,xfi-pll = <&xfi_pll>; - mediatek,infracfg = <&topmisc>; - mediatek,toprgu = <&watchdog>; - #reset-cells = <1>; - #address-cells = <1>; - #size-cells = <0>; - - gmac0: mac@0 { - compatible = "mediatek,eth-mac"; - reg = <0>; - phy-mode = "internal"; - status = "disabled"; - - fixed-link { - speed = <10000>; - full-duplex; - pause; - }; - }; - - gmac1: mac@1 { - compatible = "mediatek,eth-mac"; - reg = <1>; - status = "disabled"; - }; - - gmac2: mac@2 { - compatible = "mediatek,eth-mac"; - reg = <2>; - status = "disabled"; - }; - - mdio_bus: mdio-bus { - #address-cells = <1>; - #size-cells = <0>; - - /* internal 2.5G PHY */ - int_2p5g_phy: ethernet-phy@15 { - compatible = "ethernet-phy-ieee802.3-c45"; - reg = <15>; - phy-mode = "internal"; - }; - }; - }; - - crypto: crypto@15600000 { - compatible = "inside-secure,safexcel-eip197b"; - reg = <0 0x15600000 0 0x180000>; - interrupts = , - , - , - ; - interrupt-names = "ring0", "ring1", "ring2", "ring3"; - status = "okay"; - }; - }; - - thermal-zones { - cpu_thermal: cpu-thermal { - polling-delay-passive = <1000>; - polling-delay = <1000>; - thermal-sensors = <&lvts 0>; - - trips { - cpu_trip_crit: crit { - temperature = <125000>; - hysteresis = <2000>; - type = "critical"; - }; - - cpu_trip_hot: hot { - temperature = <120000>; - hysteresis = <2000>; - type = "hot"; - }; - - cpu_trip_active_high: active-high { - temperature = <115000>; - hysteresis = <2000>; - type = "active"; - }; - - cpu_trip_active_med: active-med { - temperature = <85000>; - hysteresis = <2000>; - type = "active"; - }; - - cpu_trip_active_low: active-low { - temperature = <40000>; - hysteresis = <2000>; - type = "active"; - }; - }; - - cooling-maps { - cpu-active-high { - /* active: set fan to cooling level 2 */ - cooling-device = <&fan 3 3>; - trip = <&cpu_trip_active_high>; - }; - - cpu-active-low { - /* active: set fan to cooling level 1 */ - cooling-device = <&fan 2 2>; - trip = <&cpu_trip_active_med>; - }; - - cpu-passive { - /* passive: set fan to cooling level 0 */ - cooling-device = <&fan 1 1>; - trip = <&cpu_trip_active_low>; - }; - }; - }; - }; - - timer { - compatible = "arm,armv8-timer"; - interrupt-parent = <&gic>; - interrupts = , - , - , - ; - }; -}; diff --git a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7981-apmixed.c b/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7981-apmixed.c deleted file mode 100644 index 1647021de8..0000000000 --- a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7981-apmixed.c +++ /dev/null @@ -1,102 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Copyright (c) 2021 MediaTek Inc. - * Author: Sam Shih - * Author: Wenzhen Yu - * Author: Jianhui Zhao - * Author: Daniel Golle - */ - -#include -#include -#include -#include -#include -#include "clk-mtk.h" -#include "clk-gate.h" -#include "clk-mux.h" - -#include -#include - -#define MT7981_PLL_FMAX (2500UL * MHZ) -#define CON0_MT7981_RST_BAR BIT(27) - -#define PLL_xtal(_id, _name, _reg, _pwr_reg, _en_mask, _flags, _pcwbits, \ - _pd_reg, _pd_shift, _tuner_reg, _pcw_reg, _pcw_shift, \ - _div_table, _parent_name) \ - { \ - .id = _id, .name = _name, .reg = _reg, .pwr_reg = _pwr_reg, \ - .en_mask = _en_mask, .flags = _flags, \ - .rst_bar_mask = CON0_MT7981_RST_BAR, .fmax = MT7981_PLL_FMAX, \ - .pcwbits = _pcwbits, .pd_reg = _pd_reg, .pd_shift = _pd_shift, \ - .tuner_reg = _tuner_reg, .pcw_reg = _pcw_reg, \ - .pcw_shift = _pcw_shift, .div_table = _div_table, \ - .parent_name = _parent_name, \ - } - -#define PLL(_id, _name, _reg, _pwr_reg, _en_mask, _flags, _pcwbits, _pd_reg, \ - _pd_shift, _tuner_reg, _pcw_reg, _pcw_shift) \ - PLL_xtal(_id, _name, _reg, _pwr_reg, _en_mask, _flags, _pcwbits, \ - _pd_reg, _pd_shift, _tuner_reg, _pcw_reg, _pcw_shift, NULL, \ - "clkxtal") - -static const struct mtk_pll_data plls[] = { - PLL(CLK_APMIXED_ARMPLL, "armpll", 0x0200, 0x020C, 0x00000001, PLL_AO, - 32, 0x0200, 4, 0, 0x0204, 0), - PLL(CLK_APMIXED_NET2PLL, "net2pll", 0x0210, 0x021C, 0x00000001, 0, 32, - 0x0210, 4, 0, 0x0214, 0), - PLL(CLK_APMIXED_MMPLL, "mmpll", 0x0220, 0x022C, 0x00000001, 0, 32, - 0x0220, 4, 0, 0x0224, 0), - PLL(CLK_APMIXED_SGMPLL, "sgmpll", 0x0230, 0x023C, 0x00000001, 0, 32, - 0x0230, 4, 0, 0x0234, 0), - PLL(CLK_APMIXED_WEDMCUPLL, "wedmcupll", 0x0240, 0x024C, 0x00000001, 0, 32, - 0x0240, 4, 0, 0x0244, 0), - PLL(CLK_APMIXED_NET1PLL, "net1pll", 0x0250, 0x025C, 0x00000001, 0, 32, - 0x0250, 4, 0, 0x0254, 0), - PLL(CLK_APMIXED_MPLL, "mpll", 0x0260, 0x0270, 0x00000001, 0, 32, - 0x0260, 4, 0, 0x0264, 0), - PLL(CLK_APMIXED_APLL2, "apll2", 0x0278, 0x0288, 0x00000001, 0, 32, - 0x0278, 4, 0, 0x027C, 0), -}; - -static const struct of_device_id of_match_clk_mt7981_apmixed[] = { - { .compatible = "mediatek,mt7981-apmixedsys", }, - {} -}; - -static int clk_mt7981_apmixed_probe(struct platform_device *pdev) -{ - struct clk_onecell_data *clk_data; - struct device_node *node = pdev->dev.of_node; - int r; - - clk_data = mtk_alloc_clk_data(ARRAY_SIZE(plls)); - if (!clk_data) - return -ENOMEM; - - mtk_clk_register_plls(node, plls, ARRAY_SIZE(plls), clk_data); - - clk_prepare_enable(clk_data->clks[CLK_APMIXED_ARMPLL]); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - if (r) { - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); - goto free_apmixed_data; - } - return r; - -free_apmixed_data: - mtk_free_clk_data(clk_data); - return r; -} - -static struct platform_driver clk_mt7981_apmixed_drv = { - .probe = clk_mt7981_apmixed_probe, - .driver = { - .name = "clk-mt7981-apmixed", - .of_match_table = of_match_clk_mt7981_apmixed, - }, -}; -builtin_platform_driver(clk_mt7981_apmixed_drv); diff --git a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7981-eth.c b/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7981-eth.c deleted file mode 100644 index 4aba657aa6..0000000000 --- a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7981-eth.c +++ /dev/null @@ -1,139 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Copyright (c) 2021 MediaTek Inc. - * Author: Sam Shih - * Author: Wenzhen Yu - * Author: Jianhui Zhao - * Author: Daniel Golle - */ - -#include -#include -#include -#include -#include - -#include "clk-mtk.h" -#include "clk-gate.h" - -#include - -static const struct mtk_gate_regs sgmii0_cg_regs = { - .set_ofs = 0xE4, - .clr_ofs = 0xE4, - .sta_ofs = 0xE4, -}; - -#define GATE_SGMII0(_id, _name, _parent, _shift) { \ - .id = _id, \ - .name = _name, \ - .parent_name = _parent, \ - .regs = &sgmii0_cg_regs, \ - .shift = _shift, \ - .ops = &mtk_clk_gate_ops_no_setclr_inv, \ - } - -static const struct mtk_gate sgmii0_clks[] __initconst = { - GATE_SGMII0(CLK_SGM0_TX_EN, "sgm0_tx_en", "usb_tx250m", 2), - GATE_SGMII0(CLK_SGM0_RX_EN, "sgm0_rx_en", "usb_eq_rx250m", 3), - GATE_SGMII0(CLK_SGM0_CK0_EN, "sgm0_ck0_en", "usb_ln0", 4), - GATE_SGMII0(CLK_SGM0_CDR_CK0_EN, "sgm0_cdr_ck0_en", "usb_cdr", 5), -}; - -static const struct mtk_gate_regs sgmii1_cg_regs = { - .set_ofs = 0xE4, - .clr_ofs = 0xE4, - .sta_ofs = 0xE4, -}; - -#define GATE_SGMII1(_id, _name, _parent, _shift) { \ - .id = _id, \ - .name = _name, \ - .parent_name = _parent, \ - .regs = &sgmii1_cg_regs, \ - .shift = _shift, \ - .ops = &mtk_clk_gate_ops_no_setclr_inv, \ - } - -static const struct mtk_gate sgmii1_clks[] __initconst = { - GATE_SGMII1(CLK_SGM1_TX_EN, "sgm1_tx_en", "usb_tx250m", 2), - GATE_SGMII1(CLK_SGM1_RX_EN, "sgm1_rx_en", "usb_eq_rx250m", 3), - GATE_SGMII1(CLK_SGM1_CK1_EN, "sgm1_ck1_en", "usb_ln0", 4), - GATE_SGMII1(CLK_SGM1_CDR_CK1_EN, "sgm1_cdr_ck1_en", "usb_cdr", 5), -}; - -static const struct mtk_gate_regs eth_cg_regs = { - .set_ofs = 0x30, - .clr_ofs = 0x30, - .sta_ofs = 0x30, -}; - -#define GATE_ETH(_id, _name, _parent, _shift) { \ - .id = _id, \ - .name = _name, \ - .parent_name = _parent, \ - .regs = ð_cg_regs, \ - .shift = _shift, \ - .ops = &mtk_clk_gate_ops_no_setclr_inv, \ - } - -static const struct mtk_gate eth_clks[] __initconst = { - GATE_ETH(CLK_ETH_FE_EN, "eth_fe_en", "netsys_2x", 6), - GATE_ETH(CLK_ETH_GP2_EN, "eth_gp2_en", "sgm_325m", 7), - GATE_ETH(CLK_ETH_GP1_EN, "eth_gp1_en", "sgm_325m", 8), - GATE_ETH(CLK_ETH_WOCPU0_EN, "eth_wocpu0_en", "netsys_wed_mcu", 15), -}; - -static void __init mtk_sgmiisys_0_init(struct device_node *node) -{ - struct clk_onecell_data *clk_data; - int r; - - clk_data = mtk_alloc_clk_data(ARRAY_SIZE(sgmii0_clks)); - - mtk_clk_register_gates(node, sgmii0_clks, ARRAY_SIZE(sgmii0_clks), - clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - if (r) - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); -} -CLK_OF_DECLARE(mtk_sgmiisys_0, "mediatek,mt7981-sgmiisys_0", - mtk_sgmiisys_0_init); - -static void __init mtk_sgmiisys_1_init(struct device_node *node) -{ - struct clk_onecell_data *clk_data; - int r; - - clk_data = mtk_alloc_clk_data(ARRAY_SIZE(sgmii1_clks)); - - mtk_clk_register_gates(node, sgmii1_clks, ARRAY_SIZE(sgmii1_clks), - clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - - if (r) - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); -} -CLK_OF_DECLARE(mtk_sgmiisys_1, "mediatek,mt7981-sgmiisys_1", - mtk_sgmiisys_1_init); - -static void __init mtk_ethsys_init(struct device_node *node) -{ - struct clk_onecell_data *clk_data; - int r; - - clk_data = mtk_alloc_clk_data(ARRAY_SIZE(eth_clks)); - - mtk_clk_register_gates(node, eth_clks, ARRAY_SIZE(eth_clks), clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - - if (r) - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); -} -CLK_OF_DECLARE(mtk_ethsys, "mediatek,mt7981-ethsys", mtk_ethsys_init); diff --git a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7981-infracfg.c b/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7981-infracfg.c deleted file mode 100644 index 8416829e35..0000000000 --- a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7981-infracfg.c +++ /dev/null @@ -1,235 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Copyright (c) 2021 MediaTek Inc. - * Author: Sam Shih - * Author: Wenzhen Yu - * Author: Jianhui Zhao - * Author: Daniel Golle - */ - -#include -#include -#include -#include -#include -#include "clk-mtk.h" -#include "clk-gate.h" -#include "clk-mux.h" - -#include -#include - -static DEFINE_SPINLOCK(mt7981_clk_lock); - -static const struct mtk_fixed_factor infra_divs[] = { - FACTOR(CLK_INFRA_66M_MCK, "infra_66m_mck", "sysaxi_sel", 1, 2), -}; - -static const char *const infra_uart_parent[] __initconst = { "csw_f26m_sel", - "uart_sel" }; - -static const char *const infra_spi0_parents[] __initconst = { "i2c_sel", - "spi_sel" }; - -static const char *const infra_spi1_parents[] __initconst = { "i2c_sel", - "spim_mst_sel" }; - -static const char *const infra_pwm1_parents[] __initconst = { "pwm_sel" }; - -static const char *const infra_pwm_bsel_parents[] __initconst = { - "cb_rtc_32p7k", "csw_f26m_sel", "infra_66m_mck", "pwm_sel" -}; - -static const char *const infra_pcie_parents[] __initconst = { - "cb_rtc_32p7k", "csw_f26m_sel", "cb_cksq_40m", "pextp_tl_ck_sel" -}; - -static const struct mtk_mux infra_muxes[] = { - /* MODULE_CLK_SEL_0 */ - MUX_GATE_CLR_SET_UPD(CLK_INFRA_UART0_SEL, "infra_uart0_sel", - infra_uart_parent, 0x0018, 0x0010, 0x0014, 0, 1, - -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_UART1_SEL, "infra_uart1_sel", - infra_uart_parent, 0x0018, 0x0010, 0x0014, 1, 1, - -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_UART2_SEL, "infra_uart2_sel", - infra_uart_parent, 0x0018, 0x0010, 0x0014, 2, 1, - -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_SPI0_SEL, "infra_spi0_sel", - infra_spi0_parents, 0x0018, 0x0010, 0x0014, 4, 1, - -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_SPI1_SEL, "infra_spi1_sel", - infra_spi1_parents, 0x0018, 0x0010, 0x0014, 5, 1, - -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_SPI2_SEL, "infra_spi2_sel", - infra_spi0_parents, 0x0018, 0x0010, 0x0014, 6, 1, - -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM1_SEL, "infra_pwm1_sel", - infra_pwm1_parents, 0x0018, 0x0010, 0x0014, 9, 1, - -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM2_SEL, "infra_pwm2_sel", - infra_pwm1_parents, 0x0018, 0x0010, 0x0014, 11, 1, - -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM3_SEL, "infra_pwm3_sel", - infra_pwm1_parents, 0x0018, 0x0010, 0x0014, 15, 1, - -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM_BSEL, "infra_pwm_bsel", - infra_pwm_bsel_parents, 0x0018, 0x0010, 0x0014, 13, - 2, -1, -1, -1), - /* MODULE_CLK_SEL_1 */ - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PCIE_SEL, "infra_pcie_sel", - infra_pcie_parents, 0x0028, 0x0020, 0x0024, 0, 2, - -1, -1, -1), -}; - -static const struct mtk_gate_regs infra0_cg_regs = { - .set_ofs = 0x40, - .clr_ofs = 0x44, - .sta_ofs = 0x48, -}; - -static const struct mtk_gate_regs infra1_cg_regs = { - .set_ofs = 0x50, - .clr_ofs = 0x54, - .sta_ofs = 0x58, -}; - -static const struct mtk_gate_regs infra2_cg_regs = { - .set_ofs = 0x60, - .clr_ofs = 0x64, - .sta_ofs = 0x68, -}; - -#define GATE_INFRA0(_id, _name, _parent, _shift) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = &infra0_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_setclr, \ - } - -#define GATE_INFRA1(_id, _name, _parent, _shift) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = &infra1_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_setclr, \ - } - -#define GATE_INFRA2(_id, _name, _parent, _shift) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = &infra2_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_setclr, \ - } - -static const struct mtk_gate infra_clks[] = { - /* INFRA0 */ - GATE_INFRA0(CLK_INFRA_GPT_STA, "infra_gpt_sta", "infra_66m_mck", 0), - GATE_INFRA0(CLK_INFRA_PWM_HCK, "infra_pwm_hck", "infra_66m_mck", 1), - GATE_INFRA0(CLK_INFRA_PWM_STA, "infra_pwm_sta", "infra_pwm_bsel", 2), - GATE_INFRA0(CLK_INFRA_PWM1_CK, "infra_pwm1", "infra_pwm1_sel", 3), - GATE_INFRA0(CLK_INFRA_PWM2_CK, "infra_pwm2", "infra_pwm2_sel", 4), - GATE_INFRA0(CLK_INFRA_CQ_DMA_CK, "infra_cq_dma", "sysaxi", 6), - - GATE_INFRA0(CLK_INFRA_AUD_BUS_CK, "infra_aud_bus", "sysaxi", 8), - GATE_INFRA0(CLK_INFRA_AUD_26M_CK, "infra_aud_26m", "csw_f26m_sel", 9), - GATE_INFRA0(CLK_INFRA_AUD_L_CK, "infra_aud_l", "aud_l", 10), - GATE_INFRA0(CLK_INFRA_AUD_AUD_CK, "infra_aud_aud", "a1sys", 11), - GATE_INFRA0(CLK_INFRA_AUD_EG2_CK, "infra_aud_eg2", "a_tuner", 13), - GATE_INFRA0(CLK_INFRA_DRAMC_26M_CK, "infra_dramc_26m", "csw_f26m_sel", - 14), - GATE_INFRA0(CLK_INFRA_DBG_CK, "infra_dbg", "infra_66m_mck", 15), - GATE_INFRA0(CLK_INFRA_AP_DMA_CK, "infra_ap_dma", "infra_66m_mck", 16), - GATE_INFRA0(CLK_INFRA_SEJ_CK, "infra_sej", "infra_66m_mck", 24), - GATE_INFRA0(CLK_INFRA_SEJ_13M_CK, "infra_sej_13m", "csw_f26m_sel", 25), - GATE_INFRA0(CLK_INFRA_PWM3_CK, "infra_pwm3", "infra_pwm3_sel", 27), - /* INFRA1 */ - GATE_INFRA1(CLK_INFRA_THERM_CK, "infra_therm", "csw_f26m_sel", 0), - GATE_INFRA1(CLK_INFRA_I2C0_CK, "infra_i2c0", "i2c_bck", 1), - GATE_INFRA1(CLK_INFRA_UART0_CK, "infra_uart0", "infra_uart0_sel", 2), - GATE_INFRA1(CLK_INFRA_UART1_CK, "infra_uart1", "infra_uart1_sel", 3), - GATE_INFRA1(CLK_INFRA_UART2_CK, "infra_uart2", "infra_uart2_sel", 4), - GATE_INFRA1(CLK_INFRA_SPI2_CK, "infra_spi2", "infra_spi2_sel", 6), - GATE_INFRA1(CLK_INFRA_SPI2_HCK_CK, "infra_spi2_hck", "infra_66m_mck", 7), - GATE_INFRA1(CLK_INFRA_NFI1_CK, "infra_nfi1", "nfi1x", 8), - GATE_INFRA1(CLK_INFRA_SPINFI1_CK, "infra_spinfi1", "spinfi_bck", 9), - GATE_INFRA1(CLK_INFRA_NFI_HCK_CK, "infra_nfi_hck", "infra_66m_mck", 10), - GATE_INFRA1(CLK_INFRA_SPI0_CK, "infra_spi0", "infra_spi0_sel", 11), - GATE_INFRA1(CLK_INFRA_SPI1_CK, "infra_spi1", "infra_spi1_sel", 12), - GATE_INFRA1(CLK_INFRA_SPI0_HCK_CK, "infra_spi0_hck", "infra_66m_mck", - 13), - GATE_INFRA1(CLK_INFRA_SPI1_HCK_CK, "infra_spi1_hck", "infra_66m_mck", - 14), - GATE_INFRA1(CLK_INFRA_FRTC_CK, "infra_frtc", "cb_rtc_32k", 15), - GATE_INFRA1(CLK_INFRA_MSDC_CK, "infra_msdc", "emmc_400m", 16), - GATE_INFRA1(CLK_INFRA_MSDC_HCK_CK, "infra_msdc_hck", "emmc_208m", 17), - GATE_INFRA1(CLK_INFRA_MSDC_133M_CK, "infra_msdc_133m", "sysaxi", 18), - GATE_INFRA1(CLK_INFRA_MSDC_66M_CK, "infra_msdc_66m", "sysaxi", 19), - GATE_INFRA1(CLK_INFRA_ADC_26M_CK, "infra_adc_26m", "infra_adc_frc", 20), - GATE_INFRA1(CLK_INFRA_ADC_FRC_CK, "infra_adc_frc", "csw_f26m", 21), - GATE_INFRA1(CLK_INFRA_FBIST2FPC_CK, "infra_fbist2fpc", "nfi1x", 23), - GATE_INFRA1(CLK_INFRA_I2C_MCK_CK, "infra_i2c_mck", "sysaxi", 25), - GATE_INFRA1(CLK_INFRA_I2C_PCK_CK, "infra_i2c_pck", "infra_66m_mck", 26), - /* INFRA2 */ - GATE_INFRA2(CLK_INFRA_IUSB_133_CK, "infra_iusb_133", "sysaxi", 0), - GATE_INFRA2(CLK_INFRA_IUSB_66M_CK, "infra_iusb_66m", "sysaxi", 1), - GATE_INFRA2(CLK_INFRA_IUSB_SYS_CK, "infra_iusb_sys", "u2u3_sys", 2), - GATE_INFRA2(CLK_INFRA_IUSB_CK, "infra_iusb", "u2u3_ref", 3), - GATE_INFRA2(CLK_INFRA_IPCIE_CK, "infra_ipcie", "pextp_tl", 12), - GATE_INFRA2(CLK_INFRA_IPCIE_PIPE_CK, "infra_ipcie_pipe", "cb_cksq_40m", - 13), - GATE_INFRA2(CLK_INFRA_IPCIER_CK, "infra_ipcier", "csw_f26m", 14), - GATE_INFRA2(CLK_INFRA_IPCIEB_CK, "infra_ipcieb", "sysaxi", 15), -}; - -static int clk_mt7981_infracfg_probe(struct platform_device *pdev) -{ - struct clk_onecell_data *clk_data; - struct device_node *node = pdev->dev.of_node; - int r; - void __iomem *base; - int nr = ARRAY_SIZE(infra_divs) + ARRAY_SIZE(infra_muxes) + - ARRAY_SIZE(infra_clks); - - base = of_iomap(node, 0); - if (!base) { - pr_err("%s(): ioremap failed\n", __func__); - return -ENOMEM; - } - - clk_data = mtk_alloc_clk_data(nr); - - if (!clk_data) - return -ENOMEM; - - mtk_clk_register_factors(infra_divs, ARRAY_SIZE(infra_divs), clk_data); - mtk_clk_register_muxes(infra_muxes, ARRAY_SIZE(infra_muxes), node, - &mt7981_clk_lock, clk_data); - mtk_clk_register_gates(node, infra_clks, ARRAY_SIZE(infra_clks), - clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - if (r) { - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); - goto free_infracfg_data; - } - return r; - -free_infracfg_data: - mtk_free_clk_data(clk_data); - return r; -} - -static const struct of_device_id of_match_clk_mt7981_infracfg[] = { - { .compatible = "mediatek,mt7981-infracfg", }, - {} -}; - -static struct platform_driver clk_mt7981_infracfg_drv = { - .probe = clk_mt7981_infracfg_probe, - .driver = { - .name = "clk-mt7981-infracfg", - .of_match_table = of_match_clk_mt7981_infracfg, - }, -}; -builtin_platform_driver(clk_mt7981_infracfg_drv); diff --git a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7981-topckgen.c b/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7981-topckgen.c deleted file mode 100644 index ce6dc18672..0000000000 --- a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7981-topckgen.c +++ /dev/null @@ -1,450 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Copyright (c) 2021 MediaTek Inc. - * Author: Sam Shih - * Author: Wenzhen Yu - * Author: Jianhui Zhao - */ - - -#include -#include -#include -#include -#include -#include "clk-mtk.h" -#include "clk-gate.h" -#include "clk-mux.h" - -#include -#include - -static DEFINE_SPINLOCK(mt7981_clk_lock); - -static const struct mtk_fixed_factor top_divs[] = { - FACTOR(CLK_TOP_CB_CKSQ_40M, "cb_cksq_40m", "clkxtal", 1, 1), - FACTOR(CLK_TOP_CB_M_416M, "cb_m_416m", "mpll", 1, 1), - FACTOR(CLK_TOP_CB_M_D2, "cb_m_d2", "mpll", 1, 2), - FACTOR(CLK_TOP_CB_M_D3, "cb_m_d3", "mpll", 1, 3), - FACTOR(CLK_TOP_M_D3_D2, "m_d3_d2", "mpll", 1, 2), - FACTOR(CLK_TOP_CB_M_D4, "cb_m_d4", "mpll", 1, 4), - FACTOR(CLK_TOP_CB_M_D8, "cb_m_d8", "mpll", 1, 8), - FACTOR(CLK_TOP_M_D8_D2, "m_d8_d2", "mpll", 1, 16), - FACTOR(CLK_TOP_CB_MM_720M, "cb_mm_720m", "mmpll", 1, 1), - FACTOR(CLK_TOP_CB_MM_D2, "cb_mm_d2", "mmpll", 1, 2), - FACTOR(CLK_TOP_CB_MM_D3, "cb_mm_d3", "mmpll", 1, 3), - FACTOR(CLK_TOP_CB_MM_D3_D5, "cb_mm_d3_d5", "mmpll", 1, 15), - FACTOR(CLK_TOP_CB_MM_D4, "cb_mm_d4", "mmpll", 1, 4), - FACTOR(CLK_TOP_CB_MM_D6, "cb_mm_d6", "mmpll", 1, 6), - FACTOR(CLK_TOP_MM_D6_D2, "mm_d6_d2", "mmpll", 1, 12), - FACTOR(CLK_TOP_CB_MM_D8, "cb_mm_d8", "mmpll", 1, 8), - FACTOR(CLK_TOP_CB_APLL2_196M, "cb_apll2_196m", "apll2", 1, 1), - FACTOR(CLK_TOP_APLL2_D2, "apll2_d2", "apll2", 1, 2), - FACTOR(CLK_TOP_APLL2_D4, "apll2_d4", "apll2", 1, 4), - FACTOR(CLK_TOP_NET1_2500M, "net1_2500m", "net1pll", 1, 1), - FACTOR(CLK_TOP_CB_NET1_D4, "cb_net1_d4", "net1pll", 1, 4), - FACTOR(CLK_TOP_CB_NET1_D5, "cb_net1_d5", "net1pll", 1, 5), - FACTOR(CLK_TOP_NET1_D5_D2, "net1_d5_d2", "net1pll", 1, 10), - FACTOR(CLK_TOP_NET1_D5_D4, "net1_d5_d4", "net1pll", 1, 20), - FACTOR(CLK_TOP_CB_NET1_D8, "cb_net1_d8", "net1pll", 1, 8), - FACTOR(CLK_TOP_NET1_D8_D2, "net1_d8_d2", "net1pll", 1, 16), - FACTOR(CLK_TOP_NET1_D8_D4, "net1_d8_d4", "net1pll", 1, 32), - FACTOR(CLK_TOP_CB_NET2_800M, "cb_net2_800m", "net2pll", 1, 1), - FACTOR(CLK_TOP_CB_NET2_D2, "cb_net2_d2", "net2pll", 1, 2), - FACTOR(CLK_TOP_CB_NET2_D4, "cb_net2_d4", "net2pll", 1, 4), - FACTOR(CLK_TOP_NET2_D4_D2, "net2_d4_d2", "net2pll", 1, 8), - FACTOR(CLK_TOP_NET2_D4_D4, "net2_d4_d4", "net2pll", 1, 16), - FACTOR(CLK_TOP_CB_NET2_D6, "cb_net2_d6", "net2pll", 1, 6), - FACTOR(CLK_TOP_CB_WEDMCU_208M, "cb_wedmcu_208m", "wedmcupll", 1, 1), - FACTOR(CLK_TOP_CB_SGM_325M, "cb_sgm_325m", "sgmpll", 1, 1), - FACTOR(CLK_TOP_CKSQ_40M_D2, "cksq_40m_d2", "cb_cksq_40m", 1, 2), - FACTOR(CLK_TOP_CB_RTC_32K, "cb_rtc_32k", "cb_cksq_40m", 1, 1250), - FACTOR(CLK_TOP_CB_RTC_32P7K, "cb_rtc_32p7k", "cb_cksq_40m", 1, 1220), - FACTOR(CLK_TOP_USB_TX250M, "usb_tx250m", "cb_cksq_40m", 1, 1), - FACTOR(CLK_TOP_FAUD, "faud", "aud_sel", 1, 1), - FACTOR(CLK_TOP_NFI1X, "nfi1x", "nfi1x_sel", 1, 1), - FACTOR(CLK_TOP_USB_EQ_RX250M, "usb_eq_rx250m", "cb_cksq_40m", 1, 1), - FACTOR(CLK_TOP_USB_CDR_CK, "usb_cdr", "cb_cksq_40m", 1, 1), - FACTOR(CLK_TOP_USB_LN0_CK, "usb_ln0", "cb_cksq_40m", 1, 1), - FACTOR(CLK_TOP_SPINFI_BCK, "spinfi_bck", "spinfi_sel", 1, 1), - FACTOR(CLK_TOP_SPI, "spi", "spi_sel", 1, 1), - FACTOR(CLK_TOP_SPIM_MST, "spim_mst", "spim_mst_sel", 1, 1), - FACTOR(CLK_TOP_UART_BCK, "uart_bck", "uart_sel", 1, 1), - FACTOR(CLK_TOP_PWM_BCK, "pwm_bck", "pwm_sel", 1, 1), - FACTOR(CLK_TOP_I2C_BCK, "i2c_bck", "i2c_sel", 1, 1), - FACTOR(CLK_TOP_PEXTP_TL, "pextp_tl", "pextp_tl_ck_sel", 1, 1), - FACTOR(CLK_TOP_EMMC_208M, "emmc_208m", "emmc_208m_sel", 1, 1), - FACTOR(CLK_TOP_EMMC_400M, "emmc_400m", "emmc_400m_sel", 1, 1), - FACTOR(CLK_TOP_DRAMC_REF, "dramc_ref", "dramc_sel", 1, 1), - FACTOR(CLK_TOP_DRAMC_MD32, "dramc_md32", "dramc_md32_sel", 1, 1), - FACTOR(CLK_TOP_SYSAXI, "sysaxi", "sysaxi_sel", 1, 1), - FACTOR(CLK_TOP_SYSAPB, "sysapb", "sysapb_sel", 1, 1), - FACTOR(CLK_TOP_ARM_DB_MAIN, "arm_db_main", "arm_db_main_sel", 1, 1), - FACTOR(CLK_TOP_AP2CNN_HOST, "ap2cnn_host", "ap2cnn_host_sel", 1, 1), - FACTOR(CLK_TOP_NETSYS, "netsys", "netsys_sel", 1, 1), - FACTOR(CLK_TOP_NETSYS_500M, "netsys_500m", "netsys_500m_sel", 1, 1), - FACTOR(CLK_TOP_NETSYS_WED_MCU, "netsys_wed_mcu", "netsys_mcu_sel", 1, 1), - FACTOR(CLK_TOP_NETSYS_2X, "netsys_2x", "netsys_2x_sel", 1, 1), - FACTOR(CLK_TOP_SGM_325M, "sgm_325m", "sgm_325m_sel", 1, 1), - FACTOR(CLK_TOP_SGM_REG, "sgm_reg", "sgm_reg_sel", 1, 1), - FACTOR(CLK_TOP_F26M, "csw_f26m", "csw_f26m_sel", 1, 1), - FACTOR(CLK_TOP_EIP97B, "eip97b", "eip97b_sel", 1, 1), - FACTOR(CLK_TOP_USB3_PHY, "usb3_phy", "usb3_phy_sel", 1, 1), - FACTOR(CLK_TOP_AUD, "aud", "faud", 1, 1), - FACTOR(CLK_TOP_A1SYS, "a1sys", "a1sys_sel", 1, 1), - FACTOR(CLK_TOP_AUD_L, "aud_l", "aud_l_sel", 1, 1), - FACTOR(CLK_TOP_A_TUNER, "a_tuner", "a_tuner_sel", 1, 1), - FACTOR(CLK_TOP_U2U3_REF, "u2u3_ref", "u2u3_sel", 1, 1), - FACTOR(CLK_TOP_U2U3_SYS, "u2u3_sys", "u2u3_sys_sel", 1, 1), - FACTOR(CLK_TOP_U2U3_XHCI, "u2u3_xhci", "u2u3_xhci_sel", 1, 1), - FACTOR(CLK_TOP_USB_FRMCNT, "usb_frmcnt", "usb_frmcnt_sel", 1, 1), -}; - -static const char * const nfi1x_parents[] __initconst = { - "cb_cksq_40m", - "cb_mm_d4", - "net1_d8_d2", - "cb_net2_d6", - "cb_m_d4", - "cb_mm_d8", - "net1_d8_d4", - "cb_m_d8" -}; - -static const char * const spinfi_parents[] __initconst = { - "cksq_40m_d2", - "cb_cksq_40m", - "net1_d5_d4", - "cb_m_d4", - "cb_mm_d8", - "net1_d8_d4", - "mm_d6_d2", - "cb_m_d8" -}; - -static const char * const spi_parents[] __initconst = { - "cb_cksq_40m", - "cb_m_d2", - "cb_mm_d4", - "net1_d8_d2", - "cb_net2_d6", - "net1_d5_d4", - "cb_m_d4", - "net1_d8_d4" -}; - -static const char * const uart_parents[] __initconst = { - "cb_cksq_40m", - "cb_m_d8", - "m_d8_d2" -}; - -static const char * const pwm_parents[] __initconst = { - "cb_cksq_40m", - "net1_d8_d2", - "net1_d5_d4", - "cb_m_d4", - "m_d8_d2", - "cb_rtc_32k" -}; - -static const char * const i2c_parents[] __initconst = { - "cb_cksq_40m", - "net1_d5_d4", - "cb_m_d4", - "net1_d8_d4" -}; - -static const char * const pextp_tl_ck_parents[] __initconst = { - "cb_cksq_40m", - "net1_d5_d4", - "cb_m_d4", - "cb_rtc_32k" -}; - -static const char * const emmc_208m_parents[] __initconst = { - "cb_cksq_40m", - "cb_m_d2", - "cb_net2_d4", - "cb_apll2_196m", - "cb_mm_d4", - "net1_d8_d2", - "cb_mm_d6" -}; - -static const char * const emmc_400m_parents[] __initconst = { - "cb_cksq_40m", - "cb_net2_d2", - "cb_mm_d2", - "cb_net2_d2" -}; - -static const char * const csw_f26m_parents[] __initconst = { - "cksq_40m_d2", - "m_d8_d2" -}; - -static const char * const dramc_md32_parents[] __initconst = { - "cb_cksq_40m", - "cb_m_d2", - "cb_wedmcu_208m" -}; - -static const char * const sysaxi_parents[] __initconst = { - "cb_cksq_40m", - "net1_d8_d2" -}; - -static const char * const sysapb_parents[] __initconst = { - "cb_cksq_40m", - "m_d3_d2" -}; - -static const char * const arm_db_main_parents[] __initconst = { - "cb_cksq_40m", - "cb_net2_d6" -}; - -static const char * const ap2cnn_host_parents[] __initconst = { - "cb_cksq_40m", - "net1_d8_d4" -}; - -static const char * const netsys_parents[] __initconst = { - "cb_cksq_40m", - "cb_mm_d2" -}; - -static const char * const netsys_500m_parents[] __initconst = { - "cb_cksq_40m", - "cb_net1_d5" -}; - -static const char * const netsys_mcu_parents[] __initconst = { - "cb_cksq_40m", - "cb_mm_720m", - "cb_net1_d4", - "cb_net1_d5", - "cb_m_416m" -}; - -static const char * const netsys_2x_parents[] __initconst = { - "cb_cksq_40m", - "cb_net2_800m", - "cb_mm_720m" -}; - -static const char * const sgm_325m_parents[] __initconst = { - "cb_cksq_40m", - "cb_sgm_325m" -}; - -static const char * const sgm_reg_parents[] __initconst = { - "cb_cksq_40m", - "cb_net2_d4" -}; - -static const char * const eip97b_parents[] __initconst = { - "cb_cksq_40m", - "cb_net1_d5", - "cb_m_416m", - "cb_mm_d2", - "net1_d5_d2" -}; - -static const char * const aud_parents[] __initconst = { - "cb_cksq_40m", - "cb_apll2_196m" -}; - -static const char * const a1sys_parents[] __initconst = { - "cb_cksq_40m", - "apll2_d4" -}; - -static const char * const aud_l_parents[] __initconst = { - "cb_cksq_40m", - "cb_apll2_196m", - "m_d8_d2" -}; - -static const char * const a_tuner_parents[] __initconst = { - "cb_cksq_40m", - "apll2_d4", - "m_d8_d2" -}; - -static const char * const u2u3_parents[] __initconst = { - "cb_cksq_40m", - "m_d8_d2" -}; - -static const char * const u2u3_sys_parents[] __initconst = { - "cb_cksq_40m", - "net1_d5_d4" -}; - -static const char * const usb_frmcnt_parents[] __initconst = { - "cb_cksq_40m", - "cb_mm_d3_d5" -}; - -static const struct mtk_mux top_muxes[] = { - /* CLK_CFG_0 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_NFI1X_SEL, "nfi1x_sel", nfi1x_parents, - 0x000, 0x004, 0x008, 0, 3, 7, 0x1C0, 0), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SPINFI_SEL, "spinfi_sel", spinfi_parents, - 0x000, 0x004, 0x008, 8, 3, 15, 0x1C0, 1), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SPI_SEL, "spi_sel", spi_parents, - 0x000, 0x004, 0x008, 16, 3, 23, 0x1C0, 2), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SPIM_MST_SEL, "spim_mst_sel", spi_parents, - 0x000, 0x004, 0x008, 24, 3, 31, 0x1C0, 3), - /* CLK_CFG_1 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_UART_SEL, "uart_sel", uart_parents, - 0x010, 0x014, 0x018, 0, 2, 7, 0x1C0, 4), - MUX_GATE_CLR_SET_UPD(CLK_TOP_PWM_SEL, "pwm_sel", pwm_parents, - 0x010, 0x014, 0x018, 8, 3, 15, 0x1C0, 5), - MUX_GATE_CLR_SET_UPD(CLK_TOP_I2C_SEL, "i2c_sel", i2c_parents, - 0x010, 0x014, 0x018, 16, 2, 23, 0x1C0, 6), - MUX_GATE_CLR_SET_UPD(CLK_TOP_PEXTP_TL_SEL, "pextp_tl_ck_sel", - pextp_tl_ck_parents, 0x010, 0x014, 0x018, 24, 2, 31, - 0x1C0, 7), - /* CLK_CFG_2 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_EMMC_208M_SEL, "emmc_208m_sel", - emmc_208m_parents, 0x020, 0x024, 0x028, 0, 3, 7, - 0x1C0, 8), - MUX_GATE_CLR_SET_UPD(CLK_TOP_EMMC_400M_SEL, "emmc_400m_sel", - emmc_400m_parents, 0x020, 0x024, 0x028, 8, 2, 15, - 0x1C0, 9), - MUX_GATE_CLR_SET_UPD_FLAGS(CLK_TOP_F26M_SEL, "csw_f26m_sel", - csw_f26m_parents, 0x020, 0x024, 0x028, 16, 1, 23, - 0x1C0, 10, - CLK_IS_CRITICAL | CLK_SET_RATE_PARENT), - MUX_GATE_CLR_SET_UPD_FLAGS(CLK_TOP_DRAMC_SEL, "dramc_sel", - csw_f26m_parents, 0x020, 0x024, 0x028, 24, 1, - 31, 0x1C0, 11, - CLK_IS_CRITICAL | CLK_SET_RATE_PARENT), - /* CLK_CFG_3 */ - MUX_GATE_CLR_SET_UPD_FLAGS(CLK_TOP_DRAMC_MD32_SEL, "dramc_md32_sel", - dramc_md32_parents, 0x030, 0x034, 0x038, 0, 2, - 7, 0x1C0, 12, - CLK_IS_CRITICAL | CLK_SET_RATE_PARENT), - MUX_GATE_CLR_SET_UPD_FLAGS(CLK_TOP_SYSAXI_SEL, "sysaxi_sel", - sysaxi_parents, 0x030, 0x034, 0x038, 8, 1, 15, - 0x1C0, 13, - CLK_IS_CRITICAL | CLK_SET_RATE_PARENT), - MUX_GATE_CLR_SET_UPD_FLAGS(CLK_TOP_SYSAPB_SEL, "sysapb_sel", - sysapb_parents, 0x030, 0x034, 0x038, 16, 1, - 23, 0x1C0, 14, - CLK_IS_CRITICAL | CLK_SET_RATE_PARENT), - MUX_GATE_CLR_SET_UPD(CLK_TOP_ARM_DB_MAIN_SEL, "arm_db_main_sel", - arm_db_main_parents, 0x030, 0x034, 0x038, 24, 1, 31, - 0x1C0, 15), - /* CLK_CFG_4 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_AP2CNN_HOST_SEL, "ap2cnn_host_sel", - ap2cnn_host_parents, 0x040, 0x044, 0x048, 0, 1, 7, - 0x1C0, 16), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_SEL, "netsys_sel", netsys_parents, - 0x040, 0x044, 0x048, 8, 1, 15, 0x1C0, 17), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_500M_SEL, "netsys_500m_sel", - netsys_500m_parents, 0x040, 0x044, 0x048, 16, 1, 23, - 0x1C0, 18), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_MCU_SEL, "netsys_mcu_sel", - netsys_mcu_parents, 0x040, 0x044, 0x048, 24, 3, 31, - 0x1C0, 19), - /* CLK_CFG_5 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_2X_SEL, "netsys_2x_sel", - netsys_2x_parents, 0x050, 0x054, 0x058, 0, 2, 7, - 0x1C0, 20), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SGM_325M_SEL, "sgm_325m_sel", - sgm_325m_parents, 0x050, 0x054, 0x058, 8, 1, 15, - 0x1C0, 21), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SGM_REG_SEL, "sgm_reg_sel", sgm_reg_parents, - 0x050, 0x054, 0x058, 16, 1, 23, 0x1C0, 22), - MUX_GATE_CLR_SET_UPD(CLK_TOP_EIP97B_SEL, "eip97b_sel", eip97b_parents, - 0x050, 0x054, 0x058, 24, 3, 31, 0x1C0, 23), - /* CLK_CFG_6 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_USB3_PHY_SEL, "usb3_phy_sel", - csw_f26m_parents, 0x060, 0x064, 0x068, 0, 1, - 7, 0x1C0, 24), - MUX_GATE_CLR_SET_UPD(CLK_TOP_AUD_SEL, "aud_sel", aud_parents, 0x060, - 0x064, 0x068, 8, 1, 15, 0x1C0, 25), - MUX_GATE_CLR_SET_UPD(CLK_TOP_A1SYS_SEL, "a1sys_sel", a1sys_parents, - 0x060, 0x064, 0x068, 16, 1, 23, 0x1C0, 26), - MUX_GATE_CLR_SET_UPD(CLK_TOP_AUD_L_SEL, "aud_l_sel", aud_l_parents, - 0x060, 0x064, 0x068, 24, 2, 31, 0x1C0, 27), - /* CLK_CFG_7 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_A_TUNER_SEL, "a_tuner_sel", - a_tuner_parents, 0x070, 0x074, 0x078, 0, 2, 7, - 0x1C0, 28), - MUX_GATE_CLR_SET_UPD(CLK_TOP_U2U3_SEL, "u2u3_sel", u2u3_parents, 0x070, - 0x074, 0x078, 8, 1, 15, 0x1C0, 29), - MUX_GATE_CLR_SET_UPD(CLK_TOP_U2U3_SYS_SEL, "u2u3_sys_sel", - u2u3_sys_parents, 0x070, 0x074, 0x078, 16, 1, 23, - 0x1C0, 30), - MUX_GATE_CLR_SET_UPD(CLK_TOP_U2U3_XHCI_SEL, "u2u3_xhci_sel", - u2u3_sys_parents, 0x070, 0x074, 0x078, 24, 1, 31, - 0x1C4, 0), - /* CLK_CFG_8 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_USB_FRMCNT_SEL, "usb_frmcnt_sel", - usb_frmcnt_parents, 0x080, 0x084, 0x088, 0, 1, 7, - 0x1C4, 1), -}; - -static struct mtk_composite top_aud_divs[] = { - DIV_GATE(CLK_TOP_AUD_I2S_M, "aud_i2s_m", "aud", - 0x0420, 0, 0x0420, 8, 8), -}; - -static int clk_mt7981_topckgen_probe(struct platform_device *pdev) -{ - struct clk_onecell_data *clk_data; - struct device_node *node = pdev->dev.of_node; - int r; - void __iomem *base; - int nr = ARRAY_SIZE(top_divs) + ARRAY_SIZE(top_muxes) + - ARRAY_SIZE(top_aud_divs); - - base = of_iomap(node, 0); - if (!base) { - pr_err("%s(): ioremap failed\n", __func__); - return -ENOMEM; - } - - clk_data = mtk_alloc_clk_data(nr); - if (!clk_data) - return -ENOMEM; - - mtk_clk_register_factors(top_divs, ARRAY_SIZE(top_divs), clk_data); - mtk_clk_register_muxes(top_muxes, ARRAY_SIZE(top_muxes), node, - &mt7981_clk_lock, clk_data); - mtk_clk_register_composites(top_aud_divs, ARRAY_SIZE(top_aud_divs), base, - &mt7981_clk_lock, clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - - if (r) { - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); - goto free_topckgen_data; - } - return r; - -free_topckgen_data: - mtk_free_clk_data(clk_data); - return r; -} - -static const struct of_device_id of_match_clk_mt7981_topckgen[] = { - { .compatible = "mediatek,mt7981-topckgen", }, - {} -}; - -static struct platform_driver clk_mt7981_topckgen_drv = { - .probe = clk_mt7981_topckgen_probe, - .driver = { - .name = "clk-mt7981-topckgen", - .of_match_table = of_match_clk_mt7981_topckgen, - }, -}; -builtin_platform_driver(clk_mt7981_topckgen_drv); diff --git a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7986-apmixed.c b/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7986-apmixed.c deleted file mode 100644 index 76c8ebdeae..0000000000 --- a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7986-apmixed.c +++ /dev/null @@ -1,100 +0,0 @@ -// SPDX-License-Identifier: GPL-1.0 -/* - * Copyright (c) 2021 MediaTek Inc. - * Author: Sam Shih - * Author: Wenzhen Yu - */ - -#include -#include -#include -#include -#include -#include "clk-mtk.h" -#include "clk-gate.h" -#include "clk-mux.h" - -#include -#include - -#define MT7986_PLL_FMAX (2500UL * MHZ) -#define CON0_MT7986_RST_BAR BIT(27) - -#define PLL_xtal(_id, _name, _reg, _pwr_reg, _en_mask, _flags, _pcwbits, \ - _pd_reg, _pd_shift, _tuner_reg, _pcw_reg, _pcw_shift, \ - _div_table, _parent_name) \ - { \ - .id = _id, .name = _name, .reg = _reg, .pwr_reg = _pwr_reg, \ - .en_mask = _en_mask, .flags = _flags, \ - .rst_bar_mask = CON0_MT7986_RST_BAR, .fmax = MT7986_PLL_FMAX, \ - .pcwbits = _pcwbits, .pd_reg = _pd_reg, .pd_shift = _pd_shift, \ - .tuner_reg = _tuner_reg, .pcw_reg = _pcw_reg, \ - .pcw_shift = _pcw_shift, .div_table = _div_table, \ - .parent_name = _parent_name, \ - } - -#define PLL(_id, _name, _reg, _pwr_reg, _en_mask, _flags, _pcwbits, _pd_reg, \ - _pd_shift, _tuner_reg, _pcw_reg, _pcw_shift) \ - PLL_xtal(_id, _name, _reg, _pwr_reg, _en_mask, _flags, _pcwbits, \ - _pd_reg, _pd_shift, _tuner_reg, _pcw_reg, _pcw_shift, NULL, \ - "clkxtal") - -static const struct mtk_pll_data plls[] = { - PLL(CLK_APMIXED_ARMPLL, "armpll", 0x0200, 0x020C, 0x00000001, 0, 32, - 0x0200, 4, 0, 0x0204, 0), - PLL(CLK_APMIXED_NET2PLL, "net2pll", 0x0210, 0x021C, 0x00000001, 0, 32, - 0x0210, 4, 0, 0x0214, 0), - PLL(CLK_APMIXED_MMPLL, "mmpll", 0x0220, 0x022C, 0x00000001, 0, 32, - 0x0220, 4, 0, 0x0224, 0), - PLL(CLK_APMIXED_SGMPLL, "sgmpll", 0x0230, 0x023c, 0x00000001, 0, 32, - 0x0230, 4, 0, 0x0234, 0), - PLL(CLK_APMIXED_WEDMCUPLL, "wedmcupll", 0x0240, 0x024c, 0x00000001, 0, - 32, 0x0240, 4, 0, 0x0244, 0), - PLL(CLK_APMIXED_NET1PLL, "net1pll", 0x0250, 0x025c, 0x00000001, 0, 32, - 0x0250, 4, 0, 0x0254, 0), - PLL(CLK_APMIXED_MPLL, "mpll", 0x0260, 0x0270, 0x00000001, 0, 32, 0x0260, - 4, 0, 0x0264, 0), - PLL(CLK_APMIXED_APLL2, "apll2", 0x0278, 0x0288, 0x00000001, 0, 32, - 0x0278, 4, 0, 0x027c, 0), -}; - -static const struct of_device_id of_match_clk_mt7986_apmixed[] = { - { .compatible = "mediatek,mt7986-apmixedsys", }, - {} -}; - -static int clk_mt7986_apmixed_probe(struct platform_device *pdev) -{ - struct clk_onecell_data *clk_data; - struct device_node *node = pdev->dev.of_node; - int r; - - clk_data = mtk_alloc_clk_data(ARRAY_SIZE(plls)); - if (!clk_data) - return -ENOMEM; - - mtk_clk_register_plls(node, plls, ARRAY_SIZE(plls), clk_data); - - clk_prepare_enable(clk_data->clks[CLK_APMIXED_ARMPLL]); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - if (r) { - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); - goto free_apmixed_data; - } - return r; - -free_apmixed_data: - mtk_free_clk_data(clk_data); - return r; -} - -static struct platform_driver clk_mt7986_apmixed_drv = { - .probe = clk_mt7986_apmixed_probe, - .driver = { - .name = "clk-mt7986-apmixed", - .of_match_table = of_match_clk_mt7986_apmixed, - }, -}; -builtin_platform_driver(clk_mt7986_apmixed_drv); diff --git a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7986-eth.c b/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7986-eth.c deleted file mode 100644 index ed2e7b2009..0000000000 --- a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7986-eth.c +++ /dev/null @@ -1,132 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Copyright (c) 2021 MediaTek Inc. - * Author: Sam Shih - * Author: Wenzhen Yu - */ - -#include -#include -#include -#include -#include - -#include "clk-mtk.h" -#include "clk-gate.h" - -#include - -static const struct mtk_gate_regs sgmii0_cg_regs = { - .set_ofs = 0xe4, - .clr_ofs = 0xe4, - .sta_ofs = 0xe4, -}; - -#define GATE_SGMII0(_id, _name, _parent, _shift) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = &sgmii0_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_no_setclr_inv, \ - } - -static const struct mtk_gate sgmii0_clks[] __initconst = { - GATE_SGMII0(CLK_SGMII0_TX250M_EN, "sgmii0_tx250m_en", "top_xtal", 2), - GATE_SGMII0(CLK_SGMII0_RX250M_EN, "sgmii0_rx250m_en", "top_xtal", 3), - GATE_SGMII0(CLK_SGMII0_CDR_REF, "sgmii0_cdr_ref", "top_xtal", 4), - GATE_SGMII0(CLK_SGMII0_CDR_FB, "sgmii0_cdr_fb", "top_xtal", 5), -}; - -static const struct mtk_gate_regs sgmii1_cg_regs = { - .set_ofs = 0xe4, - .clr_ofs = 0xe4, - .sta_ofs = 0xe4, -}; - -#define GATE_SGMII1(_id, _name, _parent, _shift) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = &sgmii1_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_no_setclr_inv, \ - } - -static const struct mtk_gate sgmii1_clks[] __initconst = { - GATE_SGMII1(CLK_SGMII1_TX250M_EN, "sgmii1_tx250m_en", "top_xtal", 2), - GATE_SGMII1(CLK_SGMII1_RX250M_EN, "sgmii1_rx250m_en", "top_xtal", 3), - GATE_SGMII1(CLK_SGMII1_CDR_REF, "sgmii1_cdr_ref", "top_xtal", 4), - GATE_SGMII1(CLK_SGMII1_CDR_FB, "sgmii1_cdr_fb", "top_xtal", 5), -}; - -static const struct mtk_gate_regs eth_cg_regs = { - .set_ofs = 0x30, - .clr_ofs = 0x30, - .sta_ofs = 0x30, -}; - -#define GATE_ETH(_id, _name, _parent, _shift) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = ð_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_no_setclr_inv, \ - } - -static const struct mtk_gate eth_clks[] __initconst = { - GATE_ETH(CLK_ETH_FE_EN, "eth_fe_en", "netsys_2x_sel", 6), - GATE_ETH(CLK_ETH_GP2_EN, "eth_gp2_en", "sgm_325m_sel", 7), - GATE_ETH(CLK_ETH_GP1_EN, "eth_gp1_en", "sgm_325m_sel", 8), - GATE_ETH(CLK_ETH_WOCPU1_EN, "eth_wocpu1_en", "netsys_mcu_sel", 14), - GATE_ETH(CLK_ETH_WOCPU0_EN, "eth_wocpu0_en", "netsys_mcu_sel", 15), -}; - -static void __init mtk_sgmiisys_0_init(struct device_node *node) -{ - struct clk_onecell_data *clk_data; - int r; - - clk_data = mtk_alloc_clk_data(ARRAY_SIZE(sgmii0_clks)); - - mtk_clk_register_gates(node, sgmii0_clks, ARRAY_SIZE(sgmii0_clks), - clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - if (r) - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); -} -CLK_OF_DECLARE(mtk_sgmiisys_0, "mediatek,mt7986-sgmiisys_0", - mtk_sgmiisys_0_init); - -static void __init mtk_sgmiisys_1_init(struct device_node *node) -{ - struct clk_onecell_data *clk_data; - int r; - - clk_data = mtk_alloc_clk_data(ARRAY_SIZE(sgmii1_clks)); - - mtk_clk_register_gates(node, sgmii1_clks, ARRAY_SIZE(sgmii1_clks), - clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - - if (r) - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); -} -CLK_OF_DECLARE(mtk_sgmiisys_1, "mediatek,mt7986-sgmiisys_1", - mtk_sgmiisys_1_init); - -static void __init mtk_ethsys_init(struct device_node *node) -{ - struct clk_onecell_data *clk_data; - int r; - - clk_data = mtk_alloc_clk_data(ARRAY_SIZE(eth_clks)); - - mtk_clk_register_gates(node, eth_clks, ARRAY_SIZE(eth_clks), clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - - if (r) - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); -} -CLK_OF_DECLARE(mtk_ethsys, "mediatek,mt7986-ethsys", mtk_ethsys_init); diff --git a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7986-infracfg.c b/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7986-infracfg.c deleted file mode 100644 index 82279dfcf5..0000000000 --- a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7986-infracfg.c +++ /dev/null @@ -1,224 +0,0 @@ -// SPDX-License-Identifier: GPL-1.0 -/* - * Copyright (c) 2021 MediaTek Inc. - * Author: Sam Shih - * Author: Wenzhen Yu - */ - -#include -#include -#include -#include -#include -#include "clk-mtk.h" -#include "clk-gate.h" -#include "clk-mux.h" - -#include -#include - -static DEFINE_SPINLOCK(mt7986_clk_lock); - -static const struct mtk_fixed_factor infra_divs[] = { - FACTOR(CLK_INFRA_SYSAXI_D2, "infra_sysaxi_d2", "sysaxi_sel", 1, 2), -}; - -static const char *const infra_uart_parent[] __initconst = { "csw_f26m_sel", - "uart_sel" }; - -static const char *const infra_spi_parents[] __initconst = { "i2c_sel", - "spi_sel" }; - -static const char *const infra_pwm_bsel_parents[] __initconst = { - "top_rtc_32p7k", "csw_f26m_sel", "infra_sysaxi_d2", "pwm_sel" -}; - -static const char *const infra_pcie_parents[] __initconst = { - "top_rtc_32p7k", "csw_f26m_sel", "top_xtal", "pextp_tl_ck_sel" -}; - -static const struct mtk_mux infra_muxes[] = { - /* MODULE_CLK_SEL_0 */ - MUX_GATE_CLR_SET_UPD(CLK_INFRA_UART0_SEL, "infra_uart0_sel", - infra_uart_parent, 0x0018, 0x0010, 0x0014, 0, 1, - -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_UART1_SEL, "infra_uart1_sel", - infra_uart_parent, 0x0018, 0x0010, 0x0014, 1, 1, - -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_UART2_SEL, "infra_uart2_sel", - infra_uart_parent, 0x0018, 0x0010, 0x0014, 2, 1, - -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_SPI0_SEL, "infra_spi0_sel", - infra_spi_parents, 0x0018, 0x0010, 0x0014, 4, 1, - -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_SPI1_SEL, "infra_spi1_sel", - infra_spi_parents, 0x0018, 0x0010, 0x0014, 5, 1, - -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM1_SEL, "infra_pwm1_sel", - infra_pwm_bsel_parents, 0x0018, 0x0010, 0x0014, 9, - 2, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM2_SEL, "infra_pwm2_sel", - infra_pwm_bsel_parents, 0x0018, 0x0010, 0x0014, 11, - 2, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM_BSEL, "infra_pwm_bsel", - infra_pwm_bsel_parents, 0x0018, 0x0010, 0x0014, 13, - 2, -1, -1, -1), - /* MODULE_CLK_SEL_1 */ - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PCIE_SEL, "infra_pcie_sel", - infra_pcie_parents, 0x0028, 0x0020, 0x0024, 0, 2, - -1, -1, -1), -}; - -static const struct mtk_gate_regs infra0_cg_regs = { - .set_ofs = 0x40, - .clr_ofs = 0x44, - .sta_ofs = 0x48, -}; - -static const struct mtk_gate_regs infra1_cg_regs = { - .set_ofs = 0x50, - .clr_ofs = 0x54, - .sta_ofs = 0x58, -}; - -static const struct mtk_gate_regs infra2_cg_regs = { - .set_ofs = 0x60, - .clr_ofs = 0x64, - .sta_ofs = 0x68, -}; - -#define GATE_INFRA0(_id, _name, _parent, _shift) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = &infra0_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_setclr, \ - } - -#define GATE_INFRA1(_id, _name, _parent, _shift) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = &infra1_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_setclr, \ - } - -#define GATE_INFRA2(_id, _name, _parent, _shift) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = &infra2_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_setclr, \ - } - -static const struct mtk_gate infra_clks[] = { - /* INFRA0 */ - GATE_INFRA0(CLK_INFRA_GPT_STA, "infra_gpt_sta", "infra_sysaxi_d2", 0), - GATE_INFRA0(CLK_INFRA_PWM_HCK, "infra_pwm_hck", "infra_sysaxi_d2", 1), - GATE_INFRA0(CLK_INFRA_PWM_STA, "infra_pwm_sta", "infra_pwm_bsel", 2), - GATE_INFRA0(CLK_INFRA_PWM1_CK, "infra_pwm1", "infra_pwm1_sel", 3), - GATE_INFRA0(CLK_INFRA_PWM2_CK, "infra_pwm2", "infra_pwm2_sel", 4), - GATE_INFRA0(CLK_INFRA_CQ_DMA_CK, "infra_cq_dma", "sysaxi_sel", 6), - GATE_INFRA0(CLK_INFRA_EIP97_CK, "infra_eip97", "eip_b_sel", 7), - GATE_INFRA0(CLK_INFRA_AUD_BUS_CK, "infra_aud_bus", "sysaxi_sel", 8), - GATE_INFRA0(CLK_INFRA_AUD_26M_CK, "infra_aud_26m", "csw_f26m_sel", 9), - GATE_INFRA0(CLK_INFRA_AUD_L_CK, "infra_aud_l", "aud_l_sel", 10), - GATE_INFRA0(CLK_INFRA_AUD_AUD_CK, "infra_aud_aud", "a1sys_sel", 11), - GATE_INFRA0(CLK_INFRA_AUD_EG2_CK, "infra_aud_eg2", "a_tuner_sel", 13), - GATE_INFRA0(CLK_INFRA_DRAMC_26M_CK, "infra_dramc_26m", "csw_f26m_sel", - 14), - GATE_INFRA0(CLK_INFRA_DBG_CK, "infra_dbg", "infra_sysaxi_d2", 15), - GATE_INFRA0(CLK_INFRA_AP_DMA_CK, "infra_ap_dma", "infra_sysaxi_d2", 16), - GATE_INFRA0(CLK_INFRA_SEJ_CK, "infra_sej", "infra_sysaxi_d2", 24), - GATE_INFRA0(CLK_INFRA_SEJ_13M_CK, "infra_sej_13m", "csw_f26m_sel", 25), - GATE_INFRA0(CLK_INFRA_TRNG_CK, "infra_trng", "sysaxi_sel", 26), - /* INFRA1 */ - GATE_INFRA1(CLK_INFRA_THERM_CK, "infra_therm", "csw_f26m_sel", 0), - GATE_INFRA1(CLK_INFRA_I2C0_CK, "infra_i2c0", "i2c_sel", 1), - GATE_INFRA1(CLK_INFRA_UART0_CK, "infra_uart0", "infra_uart0_sel", 2), - GATE_INFRA1(CLK_INFRA_UART1_CK, "infra_uart1", "infra_uart1_sel", 3), - GATE_INFRA1(CLK_INFRA_UART2_CK, "infra_uart2", "infra_uart2_sel", 4), - GATE_INFRA1(CLK_INFRA_NFI1_CK, "infra_nfi1", "nfi1x_sel", 8), - GATE_INFRA1(CLK_INFRA_SPINFI1_CK, "infra_spinfi1", "spinfi_sel", 9), - GATE_INFRA1(CLK_INFRA_NFI_HCK_CK, "infra_nfi_hck", "infra_sysaxi_d2", - 10), - GATE_INFRA1(CLK_INFRA_SPI0_CK, "infra_spi0", "infra_spi0_sel", 11), - GATE_INFRA1(CLK_INFRA_SPI1_CK, "infra_spi1", "infra_spi1_sel", 12), - GATE_INFRA1(CLK_INFRA_SPI0_HCK_CK, "infra_spi0_hck", "infra_sysaxi_d2", - 13), - GATE_INFRA1(CLK_INFRA_SPI1_HCK_CK, "infra_spi1_hck", "infra_sysaxi_d2", - 14), - GATE_INFRA1(CLK_INFRA_FRTC_CK, "infra_frtc", "top_rtc_32k", 15), - GATE_INFRA1(CLK_INFRA_MSDC_CK, "infra_msdc", "emmc_416m_sel", 16), - GATE_INFRA1(CLK_INFRA_MSDC_HCK_CK, "infra_msdc_hck", "emmc_250m_sel", - 17), - GATE_INFRA1(CLK_INFRA_MSDC_133M_CK, "infra_msdc_133m", "sysaxi_sel", - 18), - GATE_INFRA1(CLK_INFRA_MSDC_66M_CK, "infra_msdc_66m", "infra_sysaxi_d2", - 19), - GATE_INFRA1(CLK_INFRA_ADC_26M_CK, "infra_adc_26m", "infra_adc_frc", 20), - GATE_INFRA1(CLK_INFRA_ADC_FRC_CK, "infra_adc_frc", "csw_f26m_sel", 21), - GATE_INFRA1(CLK_INFRA_FBIST2FPC_CK, "infra_fbist2fpc", "nfi1x_sel", 23), - /* INFRA2 */ - GATE_INFRA2(CLK_INFRA_IUSB_133_CK, "infra_iusb_133", "sysaxi_sel", 0), - GATE_INFRA2(CLK_INFRA_IUSB_66M_CK, "infra_iusb_66m", "infra_sysaxi_d2", - 1), - GATE_INFRA2(CLK_INFRA_IUSB_SYS_CK, "infra_iusb_sys", "u2u3_sys_sel", 2), - GATE_INFRA2(CLK_INFRA_IUSB_CK, "infra_iusb", "u2u3_sel", 3), - GATE_INFRA2(CLK_INFRA_IPCIE_CK, "infra_ipcie", "pextp_tl_ck_sel", 12), - GATE_INFRA2(CLK_INFRA_IPCIE_PIPE_CK, "infra_ipcie_pipe", "top_xtal", - 13), - GATE_INFRA2(CLK_INFRA_IPCIER_CK, "infra_ipcier", "csw_f26m_sel", 14), - GATE_INFRA2(CLK_INFRA_IPCIEB_CK, "infra_ipcieb", "sysaxi_sel", 15), -}; - -static int clk_mt7986_infracfg_probe(struct platform_device *pdev) -{ - struct clk_onecell_data *clk_data; - struct device_node *node = pdev->dev.of_node; - int r; - void __iomem *base; - int nr = ARRAY_SIZE(infra_divs) + ARRAY_SIZE(infra_muxes) + - ARRAY_SIZE(infra_clks); - - base = of_iomap(node, 0); - if (!base) { - pr_err("%s(): ioremap failed\n", __func__); - return -ENOMEM; - } - - clk_data = mtk_alloc_clk_data(nr); - - if (!clk_data) - return -ENOMEM; - - mtk_clk_register_factors(infra_divs, ARRAY_SIZE(infra_divs), clk_data); - mtk_clk_register_muxes(infra_muxes, ARRAY_SIZE(infra_muxes), node, - &mt7986_clk_lock, clk_data); - mtk_clk_register_gates(node, infra_clks, ARRAY_SIZE(infra_clks), - clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - if (r) { - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); - goto free_infracfg_data; - } - return r; - -free_infracfg_data: - mtk_free_clk_data(clk_data); - return r; - -} - -static const struct of_device_id of_match_clk_mt7986_infracfg[] = { - { .compatible = "mediatek,mt7986-infracfg", }, - {} -}; - -static struct platform_driver clk_mt7986_infracfg_drv = { - .probe = clk_mt7986_infracfg_probe, - .driver = { - .name = "clk-mt7986-infracfg", - .of_match_table = of_match_clk_mt7986_infracfg, - }, -}; -builtin_platform_driver(clk_mt7986_infracfg_drv); diff --git a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7986-topckgen.c b/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7986-topckgen.c deleted file mode 100644 index 8550e2be77..0000000000 --- a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7986-topckgen.c +++ /dev/null @@ -1,342 +0,0 @@ -// SPDX-License-Identifier: GPL-1.0 -/* - * Copyright (c) 2021 MediaTek Inc. - * Author: Sam Shih - * Author: Wenzhen Yu - */ - -#include -#include -#include -#include -#include -#include "clk-mtk.h" -#include "clk-gate.h" -#include "clk-mux.h" - -#include -#include - -static DEFINE_SPINLOCK(mt7986_clk_lock); - -static const struct mtk_fixed_clk top_fixed_clks[] = { - FIXED_CLK(CLK_TOP_XTAL, "top_xtal", "clkxtal", 40000000), - FIXED_CLK(CLK_TOP_JTAG, "top_jtag", "clkxtal", 50000000), -}; - -static const struct mtk_fixed_factor top_divs[] = { - /* XTAL */ - FACTOR(CLK_TOP_XTAL_D2, "top_xtal_d2", "top_xtal", 1, 2), - FACTOR(CLK_TOP_RTC_32K, "top_rtc_32k", "top_xtal", 1, 1250), - FACTOR(CLK_TOP_RTC_32P7K, "top_rtc_32p7k", "top_xtal", 1, 1220), - /* MPLL */ - FACTOR(CLK_TOP_MPLL_D2, "top_mpll_d2", "mpll", 1, 2), - FACTOR(CLK_TOP_MPLL_D4, "top_mpll_d4", "mpll", 1, 4), - FACTOR(CLK_TOP_MPLL_D8, "top_mpll_d8", "mpll", 1, 8), - FACTOR(CLK_TOP_MPLL_D8_D2, "top_mpll_d8_d2", "mpll", 1, 16), - FACTOR(CLK_TOP_MPLL_D3_D2, "top_mpll_d3_d2", "mpll", 1, 6), - /* MMPLL */ - FACTOR(CLK_TOP_MMPLL_D2, "top_mmpll_d2", "mmpll", 1, 2), - FACTOR(CLK_TOP_MMPLL_D4, "top_mmpll_d4", "mmpll", 1, 4), - FACTOR(CLK_TOP_MMPLL_D8, "top_mmpll_d8", "mmpll", 1, 8), - FACTOR(CLK_TOP_MMPLL_D8_D2, "top_mmpll_d8_d2", "mmpll", 1, 16), - FACTOR(CLK_TOP_MMPLL_D3_D8, "top_mmpll_d3_d8", "mmpll", 1, 24), - FACTOR(CLK_TOP_MMPLL_U2PHY, "top_mmpll_u2phy", "mmpll", 1, 30), - /* APLL2 */ - FACTOR(CLK_TOP_APLL2_D4, "top_apll2_d4", "apll2", 1, 4), - /* NET1PLL */ - FACTOR(CLK_TOP_NET1PLL_D4, "top_net1pll_d4", "net1pll", 1, 4), - FACTOR(CLK_TOP_NET1PLL_D5, "top_net1pll_d5", "net1pll", 1, 5), - FACTOR(CLK_TOP_NET1PLL_D5_D2, "top_net1pll_d5_d2", "net1pll", 1, 10), - FACTOR(CLK_TOP_NET1PLL_D5_D4, "top_net1pll_d5_d4", "net1pll", 1, 20), - FACTOR(CLK_TOP_NET1PLL_D8_D2, "top_net1pll_d8_d2", "net1pll", 1, 16), - FACTOR(CLK_TOP_NET1PLL_D8_D4, "top_net1pll_d8_d4", "net1pll", 1, 32), - /* NET2PLL */ - FACTOR(CLK_TOP_NET2PLL_D4, "top_net2pll_d4", "net2pll", 1, 4), - FACTOR(CLK_TOP_NET2PLL_D4_D2, "top_net2pll_d4_d2", "net2pll", 1, 8), - FACTOR(CLK_TOP_NET2PLL_D3_D2, "top_net2pll_d3_d2", "net2pll", 1, 2), - /* WEDMCUPLL */ - FACTOR(CLK_TOP_WEDMCUPLL_D5_D2, "top_wedmcupll_d5_d2", "wedmcupll", 1, - 10), -}; - -static const char *const nfi1x_parents[] __initconst = { "top_xtal", - "top_mmpll_d8", - "top_net1pll_d8_d2", - "top_net2pll_d3_d2", - "top_mpll_d4", - "top_mmpll_d8_d2", - "top_wedmcupll_d5_d2", - "top_mpll_d8" }; - -static const char *const spinfi_parents[] __initconst = { - "top_xtal_d2", "top_xtal", "top_net1pll_d5_d4", - "top_mpll_d4", "top_mmpll_d8_d2", "top_wedmcupll_d5_d2", - "top_mmpll_d3_d8", "top_mpll_d8" -}; - -static const char *const spi_parents[] __initconst = { - "top_xtal", "top_mpll_d2", "top_mmpll_d8", - "top_net1pll_d8_d2", "top_net2pll_d3_d2", "top_net1pll_d5_d4", - "top_mpll_d4", "top_wedmcupll_d5_d2" -}; - -static const char *const uart_parents[] __initconst = { "top_xtal", - "top_mpll_d8", - "top_mpll_d8_d2" }; - -static const char *const pwm_parents[] __initconst = { - "top_xtal", "top_net1pll_d8_d2", "top_net1pll_d5_d4", "top_mpll_d4" -}; - -static const char *const i2c_parents[] __initconst = { - "top_xtal", "top_net1pll_d5_d4", "top_mpll_d4", "top_net1pll_d8_d4" -}; - -static const char *const pextp_tl_ck_parents[] __initconst = { - "top_xtal", "top_net1pll_d5_d4", "top_net2pll_d4_d2", "top_rtc_32k" -}; - -static const char *const emmc_250m_parents[] __initconst = { - "top_xtal", "top_net1pll_d5_d2" -}; - -static const char *const emmc_416m_parents[] __initconst = { "top_xtal", - "mpll" }; - -static const char *const f_26m_adc_parents[] __initconst = { "top_xtal", - "top_mpll_d8_d2" }; - -static const char *const dramc_md32_parents[] __initconst = { "top_xtal", - "top_mpll_d2" }; - -static const char *const sysaxi_parents[] __initconst = { "top_xtal", - "top_net1pll_d8_d2", - "top_net2pll_d4" }; - -static const char *const sysapb_parents[] __initconst = { "top_xtal", - "top_mpll_d3_d2", - "top_net2pll_d4_d2" }; - -static const char *const arm_db_main_parents[] __initconst = { - "top_xtal", "top_net2pll_d3_d2" -}; - -static const char *const arm_db_jtsel_parents[] __initconst = { "top_jtag", - "top_xtal" }; - -static const char *const netsys_parents[] __initconst = { "top_xtal", - "top_mmpll_d4" }; - -static const char *const netsys_500m_parents[] __initconst = { - "top_xtal", "top_net1pll_d5" -}; - -static const char *const netsys_mcu_parents[] __initconst = { - "top_xtal", "wedmcupll", "top_mmpll_d2", "top_net1pll_d4", - "top_net1pll_d5" -}; - -static const char *const netsys_2x_parents[] __initconst = { - "top_xtal", "net2pll", "wedmcupll", "top_mmpll_d2" -}; - -static const char *const sgm_325m_parents[] __initconst = { "top_xtal", - "sgmpll" }; - -static const char *const sgm_reg_parents[] __initconst = { - "top_xtal", "top_net1pll_d8_d4" -}; - -static const char *const a1sys_parents[] __initconst = { "top_xtal", - "top_apll2_d4" }; - -static const char *const conn_mcusys_parents[] __initconst = { "top_xtal", - "top_mmpll_d2" }; - -static const char *const eip_b_parents[] __initconst = { "top_xtal", - "net2pll" }; - -static const char *const aud_l_parents[] __initconst = { "top_xtal", "apll2", - "top_mpll_d8_d2" }; - -static const char *const a_tuner_parents[] __initconst = { "top_xtal", - "top_apll2_d4", - "top_mpll_d8_d2" }; - -static const char *const u2u3_sys_parents[] __initconst = { - "top_xtal", "top_net1pll_d5_d4" -}; - -static const char *const da_u2_refsel_parents[] __initconst = { - "top_xtal", "top_mmpll_u2phy" -}; - -static const struct mtk_mux top_muxes[] = { - /* CLK_CFG_0 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_NFI1X_SEL, "nfi1x_sel", nfi1x_parents, - 0x000, 0x004, 0x008, 0, 3, 7, 0x1C0, 0), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SPINFI_SEL, "spinfi_sel", spinfi_parents, - 0x000, 0x004, 0x008, 8, 3, 15, 0x1C0, 1), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SPI_SEL, "spi_sel", spi_parents, 0x000, - 0x004, 0x008, 16, 3, 23, 0x1C0, 2), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SPIM_MST_SEL, "spim_mst_sel", spi_parents, - 0x000, 0x004, 0x008, 24, 3, 31, 0x1C0, 3), - /* CLK_CFG_1 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_UART_SEL, "uart_sel", uart_parents, 0x010, - 0x014, 0x018, 0, 2, 7, 0x1C0, 4), - MUX_GATE_CLR_SET_UPD(CLK_TOP_PWM_SEL, "pwm_sel", pwm_parents, 0x010, - 0x014, 0x018, 8, 2, 15, 0x1C0, 5), - MUX_GATE_CLR_SET_UPD(CLK_TOP_I2C_SEL, "i2c_sel", i2c_parents, 0x010, - 0x014, 0x018, 16, 2, 23, 0x1C0, 6), - MUX_GATE_CLR_SET_UPD(CLK_TOP_PEXTP_TL_SEL, "pextp_tl_ck_sel", - pextp_tl_ck_parents, 0x010, 0x014, 0x018, 24, 2, - 31, 0x1C0, 7), - /* CLK_CFG_2 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_EMMC_250M_SEL, "emmc_250m_sel", - emmc_250m_parents, 0x020, 0x024, 0x028, 0, 1, 7, - 0x1C0, 8), - MUX_GATE_CLR_SET_UPD(CLK_TOP_EMMC_416M_SEL, "emmc_416m_sel", - emmc_416m_parents, 0x020, 0x024, 0x028, 8, 1, 15, - 0x1C0, 9), - MUX_GATE_CLR_SET_UPD(CLK_TOP_F_26M_ADC_SEL, "f_26m_adc_sel", - f_26m_adc_parents, 0x020, 0x024, 0x028, 16, 1, 23, - 0x1C0, 10), - MUX_GATE_CLR_SET_UPD(CLK_TOP_DRAMC_SEL, "dramc_sel", f_26m_adc_parents, - 0x020, 0x024, 0x028, 24, 1, 31, 0x1C0, 11), - /* CLK_CFG_3 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_DRAMC_MD32_SEL, "dramc_md32_sel", - dramc_md32_parents, 0x030, 0x034, 0x038, 0, 1, 7, - 0x1C0, 12), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SYSAXI_SEL, "sysaxi_sel", sysaxi_parents, - 0x030, 0x034, 0x038, 8, 2, 15, 0x1C0, 13), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SYSAPB_SEL, "sysapb_sel", sysapb_parents, - 0x030, 0x034, 0x038, 16, 2, 23, 0x1C0, 14), - MUX_GATE_CLR_SET_UPD(CLK_TOP_ARM_DB_MAIN_SEL, "arm_db_main_sel", - arm_db_main_parents, 0x030, 0x034, 0x038, 24, 1, - 31, 0x1C0, 15), - /* CLK_CFG_4 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_ARM_DB_JTSEL, "arm_db_jtsel", - arm_db_jtsel_parents, 0x040, 0x044, 0x048, 0, 1, 7, - 0x1C0, 16), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_SEL, "netsys_sel", netsys_parents, - 0x040, 0x044, 0x048, 8, 1, 15, 0x1C0, 17), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_500M_SEL, "netsys_500m_sel", - netsys_500m_parents, 0x040, 0x044, 0x048, 16, 1, - 23, 0x1C0, 18), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_MCU_SEL, "netsys_mcu_sel", - netsys_mcu_parents, 0x040, 0x044, 0x048, 24, 3, 31, - 0x1C0, 19), - /* CLK_CFG_5 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_2X_SEL, "netsys_2x_sel", - netsys_2x_parents, 0x050, 0x054, 0x058, 0, 2, 7, - 0x1C0, 20), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SGM_325M_SEL, "sgm_325m_sel", - sgm_325m_parents, 0x050, 0x054, 0x058, 8, 1, 15, - 0x1C0, 21), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SGM_REG_SEL, "sgm_reg_sel", - sgm_reg_parents, 0x050, 0x054, 0x058, 16, 1, 23, - 0x1C0, 22), - MUX_GATE_CLR_SET_UPD(CLK_TOP_A1SYS_SEL, "a1sys_sel", a1sys_parents, - 0x050, 0x054, 0x058, 24, 1, 31, 0x1C0, 23), - /* CLK_CFG_6 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_CONN_MCUSYS_SEL, "conn_mcusys_sel", - conn_mcusys_parents, 0x060, 0x064, 0x068, 0, 1, 7, - 0x1C0, 24), - MUX_GATE_CLR_SET_UPD(CLK_TOP_EIP_B_SEL, "eip_b_sel", eip_b_parents, - 0x060, 0x064, 0x068, 8, 1, 15, 0x1C0, 25), - MUX_GATE_CLR_SET_UPD(CLK_TOP_PCIE_PHY_SEL, "pcie_phy_sel", - f_26m_adc_parents, 0x060, 0x064, 0x068, 16, 1, 23, - 0x1C0, 26), - MUX_GATE_CLR_SET_UPD(CLK_TOP_USB3_PHY_SEL, "usb3_phy_sel", - f_26m_adc_parents, 0x060, 0x064, 0x068, 24, 1, 31, - 0x1C0, 27), - /* CLK_CFG_7 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_F26M_SEL, "csw_f26m_sel", - f_26m_adc_parents, 0x070, 0x074, 0x078, 0, 1, 7, - 0x1C0, 28), - MUX_GATE_CLR_SET_UPD(CLK_TOP_AUD_L_SEL, "aud_l_sel", aud_l_parents, - 0x070, 0x074, 0x078, 8, 2, 15, 0x1C0, 29), - MUX_GATE_CLR_SET_UPD(CLK_TOP_A_TUNER_SEL, "a_tuner_sel", - a_tuner_parents, 0x070, 0x074, 0x078, 16, 2, 23, - 0x1C0, 30), - MUX_GATE_CLR_SET_UPD(CLK_TOP_U2U3_SEL, "u2u3_sel", f_26m_adc_parents, - 0x070, 0x074, 0x078, 24, 1, 31, 0x1C4, 0), - /* CLK_CFG_8 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_U2U3_SYS_SEL, "u2u3_sys_sel", - u2u3_sys_parents, 0x080, 0x084, 0x088, 0, 1, 7, - 0x1C4, 1), - MUX_GATE_CLR_SET_UPD(CLK_TOP_U2U3_XHCI_SEL, "u2u3_xhci_sel", - u2u3_sys_parents, 0x080, 0x084, 0x088, 8, 1, 15, - 0x1C4, 2), - MUX_GATE_CLR_SET_UPD(CLK_TOP_DA_U2_REFSEL, "da_u2_refsel", - da_u2_refsel_parents, 0x080, 0x084, 0x088, 16, 1, - 23, 0x1C4, 3), - MUX_GATE_CLR_SET_UPD(CLK_TOP_DA_U2_CK_1P_SEL, "da_u2_ck_1p_sel", - da_u2_refsel_parents, 0x080, 0x084, 0x088, 24, 1, - 31, 0x1C4, 4), - /* CLK_CFG_9 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_AP2CNN_HOST_SEL, "ap2cnn_host_sel", - sgm_reg_parents, 0x090, 0x094, 0x098, 0, 1, 7, - 0x1C4, 5), -}; - -static int clk_mt7986_topckgen_probe(struct platform_device *pdev) -{ - struct clk_onecell_data *clk_data; - struct device_node *node = pdev->dev.of_node; - int r; - void __iomem *base; - int nr = ARRAY_SIZE(top_fixed_clks) + ARRAY_SIZE(top_divs) + - ARRAY_SIZE(top_muxes); - - base = of_iomap(node, 0); - if (!base) { - pr_err("%s(): ioremap failed\n", __func__); - return -ENOMEM; - } - - clk_data = mtk_alloc_clk_data(nr); - if (!clk_data) - return -ENOMEM; - - mtk_clk_register_fixed_clks(top_fixed_clks, ARRAY_SIZE(top_fixed_clks), - clk_data); - mtk_clk_register_factors(top_divs, ARRAY_SIZE(top_divs), clk_data); - mtk_clk_register_muxes(top_muxes, ARRAY_SIZE(top_muxes), node, - &mt7986_clk_lock, clk_data); - - clk_prepare_enable(clk_data->clks[CLK_TOP_SYSAXI_SEL]); - clk_prepare_enable(clk_data->clks[CLK_TOP_SYSAPB_SEL]); - clk_prepare_enable(clk_data->clks[CLK_TOP_DRAMC_SEL]); - clk_prepare_enable(clk_data->clks[CLK_TOP_DRAMC_MD32_SEL]); - clk_prepare_enable(clk_data->clks[CLK_TOP_F26M_SEL]); - clk_prepare_enable(clk_data->clks[CLK_TOP_SGM_REG_SEL]); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - - if (r) { - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); - goto free_topckgen_data; - } - return r; - -free_topckgen_data: - mtk_free_clk_data(clk_data); - return r; -} - -static const struct of_device_id of_match_clk_mt7986_topckgen[] = { - { .compatible = "mediatek,mt7986-topckgen", }, - {} -}; - -static struct platform_driver clk_mt7986_topckgen_drv = { - .probe = clk_mt7986_topckgen_probe, - .driver = { - .name = "clk-mt7986-topckgen", - .of_match_table = of_match_clk_mt7986_topckgen, - }, -}; -builtin_platform_driver(clk_mt7986_topckgen_drv); diff --git a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7988-apmixed.c b/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7988-apmixed.c deleted file mode 100644 index 587b70767e..0000000000 --- a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7988-apmixed.c +++ /dev/null @@ -1,113 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Copyright (c) 2023 MediaTek Inc. - * Author: Sam Shih - * Author: Xiufeng Li - */ - -#include -#include -#include -#include -#include -#include "clk-mtk.h" -#include "clk-gate.h" -#include "clk-mux.h" -#include - -#define MT7988_PLL_FMAX (2500UL * MHZ) -#define MT7988_PCW_CHG_SHIFT 2 - -#define PLL_xtal(_id, _name, _reg, _pwr_reg, _en_mask, _flags, _rst_bar_mask, \ - _pcwbits, _pd_reg, _pd_shift, _tuner_reg, _tuner_en_reg, \ - _tuner_en_bit, _pcw_reg, _pcw_shift, _pcw_chg_reg, \ - _div_table) \ - { \ - .id = _id, .name = _name, .reg = _reg, .pwr_reg = _pwr_reg, \ - .en_mask = _en_mask, .flags = _flags, \ - .rst_bar_mask = BIT(_rst_bar_mask), .fmax = MT7988_PLL_FMAX, \ - .pcwbits = _pcwbits, .pd_reg = _pd_reg, \ - .pd_shift = _pd_shift, .tuner_reg = _tuner_reg, \ - .tuner_en_reg = _tuner_en_reg, .tuner_en_bit = _tuner_en_bit, \ - .pcw_reg = _pcw_reg, .pcw_shift = _pcw_shift, \ - .pcw_chg_reg = _pcw_chg_reg, \ - .pcw_chg_shift = MT7988_PCW_CHG_SHIFT, \ - .div_table = _div_table, .parent_name = "clkxtal", \ - } - -#define PLL(_id, _name, _reg, _pwr_reg, _en_mask, _flags, _rst_bar_mask, \ - _pcwbits, _pd_reg, _pd_shift, _tuner_reg, _tuner_en_reg, \ - _tuner_en_bit, _pcw_reg, _pcw_shift, _pcw_chg_reg) \ - PLL_xtal(_id, _name, _reg, _pwr_reg, _en_mask, _flags, _rst_bar_mask, \ - _pcwbits, _pd_reg, _pd_shift, _tuner_reg, _tuner_en_reg, \ - _tuner_en_bit, _pcw_reg, _pcw_shift, _pcw_chg_reg, NULL) - -static const struct mtk_pll_data plls[] = { - PLL(CLK_APMIXED_NETSYSPLL, "netsyspll", 0x0104, 0x0110, 0x00000001, 0, - 0, 32, 0x0104, 4, 0, 0, 0, 0x0108, 0, 0x0104), - PLL(CLK_APMIXED_MPLL, "mpll", 0x0114, 0x0120, 0xff000001, HAVE_RST_BAR, - 23, 32, 0x0114, 4, 0, 0, 0, 0x0118, 0, 0x0114), - PLL(CLK_APMIXED_MMPLL, "mmpll", 0x0124, 0x0130, 0xff000001, - HAVE_RST_BAR, 23, 32, 0x0124, 4, 0, 0, 0, 0x0128, 0, 0x0124), - PLL(CLK_APMIXED_APLL2, "apll2", 0x0134, 0x0140, 0x00000001, 0, 0, 32, - 0x0134, 4, 0x0704, 0x0700, 1, 0x0138, 0, 0x0134), - PLL(CLK_APMIXED_NET1PLL, "net1pll", 0x0144, 0x0150, 0xff000001, - HAVE_RST_BAR, 23, 32, 0x0144, 4, 0, 0, 0, 0x0148, 0, 0x0144), - PLL(CLK_APMIXED_NET2PLL, "net2pll", 0x0154, 0x0160, 0xff000001, - (HAVE_RST_BAR | PLL_AO), 23, 32, 0x0154, 4, 0, 0, 0, 0x0158, 0, - 0x0154), - PLL(CLK_APMIXED_WEDMCUPLL, "wedmcupll", 0x0164, 0x0170, 0x00000001, 0, - 0, 32, 0x0164, 4, 0, 0, 0, 0x0168, 0, 0x0164), - PLL(CLK_APMIXED_SGMPLL, "sgmpll", 0x0174, 0x0180, 0x00000001, 0, 0, 32, - 0x0174, 4, 0, 0, 0, 0x0178, 0, 0x0174), - PLL(CLK_APMIXED_ARM_B, "arm_b", 0x0204, 0x0210, 0xff000001, - (HAVE_RST_BAR | PLL_AO), 23, 32, 0x0204, 4, 0, 0, 0, 0x0208, 0, - 0x0204), - PLL(CLK_APMIXED_CCIPLL2_B, "ccipll2_b", 0x0214, 0x0220, 0xff000001, - HAVE_RST_BAR, 23, 32, 0x0214, 4, 0, 0, 0, 0x0218, 0, 0x0214), - PLL(CLK_APMIXED_USXGMIIPLL, "usxgmiipll", 0x0304, 0x0310, 0xff000001, - HAVE_RST_BAR, 23, 32, 0x0304, 4, 0, 0, 0, 0x0308, 0, 0x0304), - PLL(CLK_APMIXED_MSDCPLL, "msdcpll", 0x0314, 0x0320, 0x00000001, 0, 0, - 32, 0x0314, 4, 0, 0, 0, 0x0318, 0, 0x0314), -}; - -static const struct of_device_id of_match_clk_mt7988_apmixed[] = { - { - .compatible = "mediatek,mt7988-apmixedsys", - }, - {} -}; - -static int clk_mt7988_apmixed_probe(struct platform_device *pdev) -{ - struct clk_onecell_data *clk_data; - struct device_node *node = pdev->dev.of_node; - int r; - - clk_data = mtk_alloc_clk_data(ARRAY_SIZE(plls)); - if (!clk_data) - return -ENOMEM; - - mtk_clk_register_plls(node, plls, ARRAY_SIZE(plls), clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - if (r) { - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); - goto free_apmixed_data; - } - return r; - -free_apmixed_data: - mtk_free_clk_data(clk_data); - return r; -} - -static struct platform_driver clk_mt7988_apmixed_drv = { - .probe = clk_mt7988_apmixed_probe, - .driver = { - .name = "clk-mt7988-apmixed", - .of_match_table = of_match_clk_mt7988_apmixed, - }, -}; -builtin_platform_driver(clk_mt7988_apmixed_drv); diff --git a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7988-eth.c b/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7988-eth.c deleted file mode 100644 index 341d0f73fd..0000000000 --- a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7988-eth.c +++ /dev/null @@ -1,299 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Copyright (c) 2023 MediaTek Inc. - * Author: Sam Shih - * Author: Xiufeng Li - */ - -#include -#include -#include -#include -#include -#include "clk-mtk.h" -#include "clk-gate.h" -#include - -static const struct mtk_gate_regs ethdma_cg_regs = { - .set_ofs = 0x30, - .clr_ofs = 0x30, - .sta_ofs = 0x30, -}; - -#define GATE_ETHDMA(_id, _name, _parent, _shift) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = ðdma_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_no_setclr_inv, \ - } - -static const struct mtk_gate ethdma_clks[] = { - GATE_ETHDMA(CLK_ETHDMA_XGP1_EN, "ethdma_xgp1_en", "top_xtal", 0), - GATE_ETHDMA(CLK_ETHDMA_XGP2_EN, "ethdma_xgp2_en", "top_xtal", 1), - GATE_ETHDMA(CLK_ETHDMA_XGP3_EN, "ethdma_xgp3_en", "top_xtal", 2), - GATE_ETHDMA(CLK_ETHDMA_FE_EN, "ethdma_fe_en", "netsys_2x_sel", 6), - GATE_ETHDMA(CLK_ETHDMA_GP2_EN, "ethdma_gp2_en", "top_xtal", 7), - GATE_ETHDMA(CLK_ETHDMA_GP1_EN, "ethdma_gp1_en", "top_xtal", 8), - GATE_ETHDMA(CLK_ETHDMA_GP3_EN, "ethdma_gp3_en", "top_xtal", 10), - GATE_ETHDMA(CLK_ETHDMA_ESW_EN, "ethdma_esw_en", "netsys_gsw_sel", 16), - GATE_ETHDMA(CLK_ETHDMA_CRYPT0_EN, "ethdma_crypt0_en", "eip197_sel", - 29), -}; - -static int clk_mt7988_ethsys_probe(struct platform_device *pdev) -{ - struct clk_onecell_data *clk_data; - struct device_node *node = pdev->dev.of_node; - int r; - void __iomem *base; - - base = of_iomap(node, 0); - if (!base) { - pr_err("%s(): ioremap failed\n", __func__); - return -ENOMEM; - } - - clk_data = mtk_alloc_clk_data(ARRAY_SIZE(ethdma_clks)); - - if (!clk_data) - return -ENOMEM; - - mtk_clk_register_gates(node, ethdma_clks, ARRAY_SIZE(ethdma_clks), - clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - if (r) { - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); - goto free_data; - } - return r; - -free_data: - mtk_free_clk_data(clk_data); - return r; -} - -static const struct mtk_gate_regs sgmii0_cg_regs = { - .set_ofs = 0xe4, - .clr_ofs = 0xe4, - .sta_ofs = 0xe4, -}; - -#define GATE_SGMII0(_id, _name, _parent, _shift) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = &sgmii0_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_no_setclr_inv, \ - } - -static const struct mtk_gate sgmii0_clks[] = { - GATE_SGMII0(CLK_SGM0_TX_EN, "sgm0_tx_en", "top_xtal", 2), - GATE_SGMII0(CLK_SGM0_RX_EN, "sgm0_rx_en", "top_xtal", 3), -}; - -static int clk_mt7988_sgmii0_probe(struct platform_device *pdev) -{ - struct clk_onecell_data *clk_data; - struct device_node *node = pdev->dev.of_node; - int r; - void __iomem *base; - - base = of_iomap(node, 0); - if (!base) { - pr_err("%s(): ioremap failed\n", __func__); - return -ENOMEM; - } - - clk_data = mtk_alloc_clk_data(ARRAY_SIZE(sgmii0_clks)); - - if (!clk_data) - return -ENOMEM; - - mtk_clk_register_gates(node, sgmii0_clks, ARRAY_SIZE(sgmii0_clks), - clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - if (r) { - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); - goto free_data; - } - return r; - -free_data: - mtk_free_clk_data(clk_data); - return r; -} - -static const struct mtk_gate_regs sgmii1_cg_regs = { - .set_ofs = 0xe4, - .clr_ofs = 0xe4, - .sta_ofs = 0xe4, -}; - -#define GATE_SGMII1(_id, _name, _parent, _shift) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = &sgmii1_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_no_setclr_inv, \ - } - -static const struct mtk_gate sgmii1_clks[] = { - GATE_SGMII1(CLK_SGM1_TX_EN, "sgm1_tx_en", "top_xtal", 2), - GATE_SGMII1(CLK_SGM1_RX_EN, "sgm1_rx_en", "top_xtal", 3), -}; - -static int clk_mt7988_sgmii1_probe(struct platform_device *pdev) -{ - struct clk_onecell_data *clk_data; - struct device_node *node = pdev->dev.of_node; - int r; - void __iomem *base; - - base = of_iomap(node, 0); - if (!base) { - pr_err("%s(): ioremap failed\n", __func__); - return -ENOMEM; - } - - clk_data = mtk_alloc_clk_data(ARRAY_SIZE(sgmii1_clks)); - - if (!clk_data) - return -ENOMEM; - - mtk_clk_register_gates(node, sgmii1_clks, ARRAY_SIZE(sgmii1_clks), - clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - if (r) { - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); - goto free_data; - } - return r; - -free_data: - mtk_free_clk_data(clk_data); - return r; -} - -static const struct mtk_gate_regs ethwarp_cg_regs = { - .set_ofs = 0x14, - .clr_ofs = 0x14, - .sta_ofs = 0x14, -}; - -#define GATE_ETHWARP(_id, _name, _parent, _shift) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = ðwarp_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_no_setclr_inv, \ - } - -static const struct mtk_gate ethwarp_clks[] = { - GATE_ETHWARP(CLK_ETHWARP_WOCPU2_EN, "ethwarp_wocpu2_en", - "netsys_mcu_sel", 13), - GATE_ETHWARP(CLK_ETHWARP_WOCPU1_EN, "ethwarp_wocpu1_en", - "netsys_mcu_sel", 14), - GATE_ETHWARP(CLK_ETHWARP_WOCPU0_EN, "ethwarp_wocpu0_en", - "netsys_mcu_sel", 15), -}; - -static int clk_mt7988_ethwarp_probe(struct platform_device *pdev) -{ - struct clk_onecell_data *clk_data; - struct device_node *node = pdev->dev.of_node; - int r; - void __iomem *base; - - base = of_iomap(node, 0); - if (!base) { - pr_err("%s(): ioremap failed\n", __func__); - return -ENOMEM; - } - - clk_data = mtk_alloc_clk_data(ARRAY_SIZE(ethwarp_clks)); - - if (!clk_data) - return -ENOMEM; - - mtk_clk_register_gates(node, ethwarp_clks, ARRAY_SIZE(ethwarp_clks), - clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - if (r) { - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); - goto free_data; - } - return r; - -free_data: - mtk_free_clk_data(clk_data); - return r; -} - -static const struct of_device_id of_match_clk_mt7988_ethsys[] = { - { - .compatible = "mediatek,mt7988-ethsys", - }, - {} -}; - -static struct platform_driver clk_mt7988_ethsys_drv = { - .probe = clk_mt7988_ethsys_probe, - .driver = { - .name = "clk-mt7988-ethsys", - .of_match_table = of_match_clk_mt7988_ethsys, - }, -}; -builtin_platform_driver(clk_mt7988_ethsys_drv); - -static const struct of_device_id of_match_clk_mt7988_sgmii0[] = { - { - .compatible = "mediatek,mt7988-sgmiisys_0", - }, - {} -}; - -static struct platform_driver clk_mt7988_sgmii0_drv = { - .probe = clk_mt7988_sgmii0_probe, - .driver = { - .name = "clk-mt7988-sgmiisys_0", - .of_match_table = of_match_clk_mt7988_sgmii0, - }, -}; -builtin_platform_driver(clk_mt7988_sgmii0_drv); - -static const struct of_device_id of_match_clk_mt7988_sgmii1[] = { - { - .compatible = "mediatek,mt7988-sgmiisys_1", - }, - {} -}; - -static struct platform_driver clk_mt7988_sgmii1_drv = { - .probe = clk_mt7988_sgmii1_probe, - .driver = { - .name = "clk-mt7988-sgmiisys_1", - .of_match_table = of_match_clk_mt7988_sgmii1, - }, -}; -builtin_platform_driver(clk_mt7988_sgmii1_drv); - -static const struct of_device_id of_match_clk_mt7988_ethwarp[] = { - { - .compatible = "mediatek,mt7988-ethwarp", - }, - {} -}; - -static struct platform_driver clk_mt7988_ethwarp_drv = { - .probe = clk_mt7988_ethwarp_probe, - .driver = { - .name = "clk-mt7988-ethwarp", - .of_match_table = of_match_clk_mt7988_ethwarp, - }, -}; -builtin_platform_driver(clk_mt7988_ethwarp_drv); \ No newline at end of file diff --git a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7988-infracfg.c b/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7988-infracfg.c deleted file mode 100644 index bce8d56375..0000000000 --- a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7988-infracfg.c +++ /dev/null @@ -1,406 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Copyright (c) 2023 MediaTek Inc. - * Author: Sam Shih - * Author: Xiufeng Li - */ - -#include -#include -#include -#include -#include -#include "clk-mtk.h" -#include "clk-gate.h" -#include "clk-mux.h" -#include - -static DEFINE_SPINLOCK(mt7988_clk_lock); - -static const char *const infra_mux_uart0_parents[] __initconst = { - "csw_infra_f26m_sel", "uart_sel" -}; - -static const char *const infra_mux_uart1_parents[] __initconst = { - "csw_infra_f26m_sel", "uart_sel" -}; - -static const char *const infra_mux_uart2_parents[] __initconst = { - "csw_infra_f26m_sel", "uart_sel" -}; - -static const char *const infra_mux_spi0_parents[] __initconst = { "i2c_sel", - "spi_sel" }; - -static const char *const infra_mux_spi1_parents[] __initconst = { - "i2c_sel", "spim_mst_sel" -}; - -static const char *const infra_pwm_bck_parents[] __initconst = { - "top_rtc_32p7k", "csw_infra_f26m_sel", "sysaxi_sel", "pwm_sel" -}; - -static const char *const infra_pcie_gfmux_tl_ck_o_p0_parents[] __initconst = { - "top_rtc_32p7k", "csw_infra_f26m_sel", "csw_infra_f26m_sel", - "pextp_tl_sel" -}; - -static const char *const infra_pcie_gfmux_tl_ck_o_p1_parents[] __initconst = { - "top_rtc_32p7k", "csw_infra_f26m_sel", "csw_infra_f26m_sel", - "pextp_tl_p1_sel" -}; - -static const char *const infra_pcie_gfmux_tl_ck_o_p2_parents[] __initconst = { - "top_rtc_32p7k", "csw_infra_f26m_sel", "csw_infra_f26m_sel", - "pextp_tl_p2_sel" -}; - -static const char *const infra_pcie_gfmux_tl_ck_o_p3_parents[] __initconst = { - "top_rtc_32p7k", "csw_infra_f26m_sel", "csw_infra_f26m_sel", - "pextp_tl_p3_sel" -}; - -static const struct mtk_mux infra_muxes[] = { - /* MODULE_CLK_SEL_0 */ - MUX_GATE_CLR_SET_UPD(CLK_INFRA_MUX_UART0_SEL, "infra_mux_uart0_sel", - infra_mux_uart0_parents, 0x0018, 0x0010, 0x0014, - 0, 1, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_MUX_UART1_SEL, "infra_mux_uart1_sel", - infra_mux_uart1_parents, 0x0018, 0x0010, 0x0014, - 1, 1, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_MUX_UART2_SEL, "infra_mux_uart2_sel", - infra_mux_uart2_parents, 0x0018, 0x0010, 0x0014, - 2, 1, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_MUX_SPI0_SEL, "infra_mux_spi0_sel", - infra_mux_spi0_parents, 0x0018, 0x0010, 0x0014, 4, - 1, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_MUX_SPI1_SEL, "infra_mux_spi1_sel", - infra_mux_spi1_parents, 0x0018, 0x0010, 0x0014, 5, - 1, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_MUX_SPI2_SEL, "infra_mux_spi2_sel", - infra_mux_spi0_parents, 0x0018, 0x0010, 0x0014, 6, - 1, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM_SEL, "infra_pwm_sel", - infra_pwm_bck_parents, 0x0018, 0x0010, 0x0014, 14, - 2, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM_CK1_SEL, "infra_pwm_ck1_sel", - infra_pwm_bck_parents, 0x0018, 0x0010, 0x0014, 16, - 2, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM_CK2_SEL, "infra_pwm_ck2_sel", - infra_pwm_bck_parents, 0x0018, 0x0010, 0x0014, 18, - 2, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM_CK3_SEL, "infra_pwm_ck3_sel", - infra_pwm_bck_parents, 0x0018, 0x0010, 0x0014, 20, - 2, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM_CK4_SEL, "infra_pwm_ck4_sel", - infra_pwm_bck_parents, 0x0018, 0x0010, 0x0014, 22, - 2, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM_CK5_SEL, "infra_pwm_ck5_sel", - infra_pwm_bck_parents, 0x0018, 0x0010, 0x0014, 24, - 2, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM_CK6_SEL, "infra_pwm_ck6_sel", - infra_pwm_bck_parents, 0x0018, 0x0010, 0x0014, 26, - 2, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM_CK7_SEL, "infra_pwm_ck7_sel", - infra_pwm_bck_parents, 0x0018, 0x0010, 0x0014, 28, - 2, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PWM_CK8_SEL, "infra_pwm_ck8_sel", - infra_pwm_bck_parents, 0x0018, 0x0010, 0x0014, 30, - 2, -1, -1, -1), - /* MODULE_CLK_SEL_1 */ - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PCIE_GFMUX_TL_O_P0_SEL, - "infra_pcie_gfmux_tl_o_p0_sel", - infra_pcie_gfmux_tl_ck_o_p0_parents, 0x0028, - 0x0020, 0x0024, 0, 2, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PCIE_GFMUX_TL_O_P1_SEL, - "infra_pcie_gfmux_tl_o_p1_sel", - infra_pcie_gfmux_tl_ck_o_p1_parents, 0x0028, - 0x0020, 0x0024, 2, 2, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PCIE_GFMUX_TL_O_P2_SEL, - "infra_pcie_gfmux_tl_o_p2_sel", - infra_pcie_gfmux_tl_ck_o_p2_parents, 0x0028, - 0x0020, 0x0024, 4, 2, -1, -1, -1), - MUX_GATE_CLR_SET_UPD(CLK_INFRA_PCIE_GFMUX_TL_O_P3_SEL, - "infra_pcie_gfmux_tl_o_p3_sel", - infra_pcie_gfmux_tl_ck_o_p3_parents, 0x0028, - 0x0020, 0x0024, 6, 2, -1, -1, -1), -}; - -static const struct mtk_gate_regs infra0_cg_regs = { - .set_ofs = 0x10, - .clr_ofs = 0x14, - .sta_ofs = 0x18, -}; - -static const struct mtk_gate_regs infra1_cg_regs = { - .set_ofs = 0x40, - .clr_ofs = 0x44, - .sta_ofs = 0x48, -}; - -static const struct mtk_gate_regs infra2_cg_regs = { - .set_ofs = 0x50, - .clr_ofs = 0x54, - .sta_ofs = 0x58, -}; - -static const struct mtk_gate_regs infra3_cg_regs = { - .set_ofs = 0x60, - .clr_ofs = 0x64, - .sta_ofs = 0x68, -}; - -#define GATE_INFRA0_FLAGS(_id, _name, _parent, _shift, _flags) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = &infra0_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_setclr, .flags = _flags, \ - } - -#define GATE_INFRA1_FLAGS(_id, _name, _parent, _shift, _flags) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = &infra1_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_setclr, .flags = _flags, \ - } - -#define GATE_INFRA2_FLAGS(_id, _name, _parent, _shift, _flags) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = &infra2_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_setclr, .flags = _flags, \ - } - -#define GATE_INFRA3_FLAGS(_id, _name, _parent, _shift, _flags) \ - { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = &infra3_cg_regs, .shift = _shift, \ - .ops = &mtk_clk_gate_ops_setclr, .flags = _flags, \ - } - -#define GATE_INFRA0(_id, _name, _parent, _shift) \ - GATE_INFRA0_FLAGS(_id, _name, _parent, _shift, 0) - -#define GATE_INFRA1(_id, _name, _parent, _shift) \ - GATE_INFRA1_FLAGS(_id, _name, _parent, _shift, 0) - -#define GATE_INFRA2(_id, _name, _parent, _shift) \ - GATE_INFRA2_FLAGS(_id, _name, _parent, _shift, 0) - -#define GATE_INFRA3(_id, _name, _parent, _shift) \ - GATE_INFRA3_FLAGS(_id, _name, _parent, _shift, 0) - -#define GATE_CRITICAL(_id, _name, _parent, _regs, _shift) { \ - .id = _id, .name = _name, .parent_name = _parent, \ - .regs = _regs, .shift = _shift, \ - .flags = CLK_IS_CRITICAL, \ - .ops = &mtk_clk_gate_ops_setclr, \ - } - -static const struct mtk_gate infra_clks[] = { - /* INFRA0 */ - GATE_INFRA0(CLK_INFRA_PCIE_PERI_26M_CK_P0, - "infra_pcie_peri_ck_26m_ck_p0", "csw_infra_f26m_sel", 7), - GATE_INFRA0(CLK_INFRA_PCIE_PERI_26M_CK_P1, - "infra_pcie_peri_ck_26m_ck_p1", "csw_infra_f26m_sel", 8), - GATE_INFRA0(CLK_INFRA_PCIE_PERI_26M_CK_P2, - "infra_pcie_peri_ck_26m_ck_p2", "csw_infra_f26m_sel", 9), - GATE_INFRA0(CLK_INFRA_PCIE_PERI_26M_CK_P3, - "infra_pcie_peri_ck_26m_ck_p3", "csw_infra_f26m_sel", 10), - /* INFRA1 */ - GATE_INFRA1(CLK_INFRA_66M_GPT_BCK, "infra_hf_66m_gpt_bck", - "sysaxi_sel", 0), - GATE_INFRA1(CLK_INFRA_66M_PWM_HCK, "infra_hf_66m_pwm_hck", - "sysaxi_sel", 1), - GATE_INFRA1(CLK_INFRA_66M_PWM_BCK, "infra_hf_66m_pwm_bck", - "infra_pwm_sel", 2), - GATE_INFRA1(CLK_INFRA_66M_PWM_CK1, "infra_hf_66m_pwm_ck1", - "infra_pwm_ck1_sel", 3), - GATE_INFRA1(CLK_INFRA_66M_PWM_CK2, "infra_hf_66m_pwm_ck2", - "infra_pwm_ck2_sel", 4), - GATE_INFRA1(CLK_INFRA_66M_PWM_CK3, "infra_hf_66m_pwm_ck3", - "infra_pwm_ck3_sel", 5), - GATE_INFRA1(CLK_INFRA_66M_PWM_CK4, "infra_hf_66m_pwm_ck4", - "infra_pwm_ck4_sel", 6), - GATE_INFRA1(CLK_INFRA_66M_PWM_CK5, "infra_hf_66m_pwm_ck5", - "infra_pwm_ck5_sel", 7), - GATE_INFRA1(CLK_INFRA_66M_PWM_CK6, "infra_hf_66m_pwm_ck6", - "infra_pwm_ck6_sel", 8), - GATE_INFRA1(CLK_INFRA_66M_PWM_CK7, "infra_hf_66m_pwm_ck7", - "infra_pwm_ck7_sel", 9), - GATE_INFRA1(CLK_INFRA_66M_PWM_CK8, "infra_hf_66m_pwm_ck8", - "infra_pwm_ck8_sel", 10), - GATE_INFRA1(CLK_INFRA_133M_CQDMA_BCK, "infra_hf_133m_cqdma_bck", - "sysaxi_sel", 12), - GATE_INFRA1(CLK_INFRA_66M_AUD_SLV_BCK, "infra_66m_aud_slv_bck", - "sysaxi_sel", 13), - GATE_INFRA1(CLK_INFRA_AUD_26M, "infra_f_faud_26m", - "csw_infra_f26m_sel", 14), - GATE_INFRA1(CLK_INFRA_AUD_L, "infra_f_faud_l", "aud_l_sel", 15), - GATE_INFRA1(CLK_INFRA_AUD_AUD, "infra_f_aud_aud", "a1sys_sel", 16), - GATE_INFRA1(CLK_INFRA_AUD_EG2, "infra_f_faud_eg2", "a_tuner_sel", 18), - GATE_INFRA1_FLAGS(CLK_INFRA_DRAMC_F26M, "infra_dramc_f26m", - "csw_infra_f26m_sel", 19, CLK_IS_CRITICAL), - // JTAG - GATE_INFRA1_FLAGS(CLK_INFRA_133M_DBG_ACKM, "infra_hf_133m_dbg_ackm", - "sysaxi_sel", 20, CLK_IS_CRITICAL), - GATE_INFRA1(CLK_INFRA_66M_AP_DMA_BCK, "infra_66m_ap_dma_bck", - "sysaxi_sel", 21), - GATE_INFRA1(CLK_INFRA_66M_SEJ_BCK, "infra_hf_66m_sej_bck", - "sysaxi_sel", 29), - GATE_INFRA1(CLK_INFRA_PRE_CK_SEJ_F13M, "infra_pre_ck_sej_f13m", - "csw_infra_f26m_sel", 30), - /* INFRA2 */ - GATE_INFRA2(CLK_INFRA_26M_THERM_SYSTEM, "infra_hf_26m_therm_system", - "csw_infra_f26m_sel", 0), - GATE_INFRA2(CLK_INFRA_I2C_BCK, "infra_i2c_bck", "i2c_sel", 1), - GATE_INFRA2(CLK_INFRA_52M_UART0_CK, "infra_f_52m_uart0", - "infra_mux_uart0_sel", 3), - GATE_INFRA2(CLK_INFRA_52M_UART1_CK, "infra_f_52m_uart1", - "infra_mux_uart1_sel", 4), - GATE_INFRA2(CLK_INFRA_52M_UART2_CK, "infra_f_52m_uart2", - "infra_mux_uart2_sel", 5), - GATE_INFRA2(CLK_INFRA_NFI, "infra_f_fnfi", "nfi1x_sel", 9), - GATE_INFRA2(CLK_INFRA_SPINFI, "infra_f_fspinfi", "spinfi_sel", 10), - GATE_INFRA2_FLAGS(CLK_INFRA_66M_NFI_HCK, "infra_hf_66m_nfi_hck", - "sysaxi_sel", 11, CLK_IS_CRITICAL), - GATE_INFRA2_FLAGS(CLK_INFRA_104M_SPI0, "infra_hf_104m_spi0", - "infra_mux_spi0_sel", 12, CLK_IS_CRITICAL), - GATE_INFRA2(CLK_INFRA_104M_SPI1, "infra_hf_104m_spi1", - "infra_mux_spi1_sel", 13), - GATE_INFRA2(CLK_INFRA_104M_SPI2_BCK, "infra_hf_104m_spi2_bck", - "infra_mux_spi2_sel", 14), - GATE_INFRA2_FLAGS(CLK_INFRA_66M_SPI0_HCK, "infra_hf_66m_spi0_hck", - "sysaxi_sel", 15, CLK_IS_CRITICAL), - GATE_INFRA2(CLK_INFRA_66M_SPI1_HCK, "infra_hf_66m_spi1_hck", - "sysaxi_sel", 16), - GATE_INFRA2(CLK_INFRA_66M_SPI2_HCK, "infra_hf_66m_spi2_hck", - "sysaxi_sel", 17), - GATE_INFRA2(CLK_INFRA_66M_FLASHIF_AXI, "infra_hf_66m_flashif_axi", - "sysaxi_sel", 18), - GATE_CRITICAL(CLK_INFRA_RTC, "infra_f_frtc", "top_rtc_32k", &infra2_cg_regs, 19), - GATE_INFRA2(CLK_INFRA_26M_ADC_BCK, "infra_f_26m_adc_bck", - "csw_infra_f26m_sel", 20), - GATE_INFRA2(CLK_INFRA_RC_ADC, "infra_f_frc_adc", "infra_f_26m_adc_bck", - 21), - GATE_INFRA2(CLK_INFRA_MSDC400, "infra_f_fmsdc400", "emmc_400m_sel", - 22), - GATE_INFRA2(CLK_INFRA_MSDC2_HCK, "infra_f_fmsdc2_hck", "emmc_250m_sel", - 23), - GATE_INFRA2(CLK_INFRA_133M_MSDC_0_HCK, "infra_hf_133m_msdc_0_hck", - "sysaxi_sel", 24), - GATE_INFRA2(CLK_INFRA_66M_MSDC_0_HCK, "infra_66m_msdc_0_hck", - "sysaxi_sel", 25), - GATE_INFRA2(CLK_INFRA_133M_CPUM_BCK, "infra_hf_133m_cpum_bck", - "sysaxi_sel", 26), - GATE_INFRA2(CLK_INFRA_BIST2FPC, "infra_hf_fbist2fpc", "nfi1x_sel", 27), - GATE_INFRA2(CLK_INFRA_I2C_X16W_MCK_CK_P1, - "infra_hf_i2c_x16w_mck_ck_p1", "sysaxi_sel", 29), - GATE_INFRA2(CLK_INFRA_I2C_X16W_PCK_CK_P1, - "infra_hf_i2c_x16w_pck_ck_p1", "sysaxi_sel", 31), - /* INFRA3 */ - GATE_INFRA3(CLK_INFRA_133M_USB_HCK, "infra_133m_usb_hck", "sysaxi_sel", - 0), - GATE_INFRA3(CLK_INFRA_133M_USB_HCK_CK_P1, "infra_133m_usb_hck_ck_p1", - "sysaxi_sel", 1), - GATE_INFRA3(CLK_INFRA_66M_USB_HCK, "infra_66m_usb_hck", "sysaxi_sel", - 2), - GATE_INFRA3(CLK_INFRA_66M_USB_HCK_CK_P1, "infra_66m_usb_hck_ck_p1", - "sysaxi_sel", 3), - GATE_INFRA3(CLK_INFRA_USB_SYS, "infra_usb_sys", "usb_sys_sel", 4), - GATE_INFRA3(CLK_INFRA_USB_SYS_CK_P1, "infra_usb_sys_ck_p1", - "usb_sys_p1_sel", 5), - GATE_INFRA3(CLK_INFRA_USB_REF, "infra_usb_ref", "top_xtal", 6), - GATE_INFRA3(CLK_INFRA_USB_CK_P1, "infra_usb_ck_p1", "top_xtal", 7), - GATE_INFRA3_FLAGS(CLK_INFRA_USB_FRMCNT, "infra_usb_frmcnt", - "usb_frmcnt_sel", 8, CLK_IS_CRITICAL), - GATE_INFRA3_FLAGS(CLK_INFRA_USB_FRMCNT_CK_P1, "infra_usb_frmcnt_ck_p1", - "usb_frmcnt_p1_sel", 9, CLK_IS_CRITICAL), - GATE_INFRA3(CLK_INFRA_USB_PIPE, "infra_usb_pipe", "sspxtp_sel", 10), - GATE_INFRA3(CLK_INFRA_USB_PIPE_CK_P1, "infra_usb_pipe_ck_p1", - "usb_phy_sel", 11), - GATE_INFRA3(CLK_INFRA_USB_UTMI, "infra_usb_utmi", "top_xtal", 12), - GATE_INFRA3(CLK_INFRA_USB_UTMI_CK_P1, "infra_usb_utmi_ck_p1", - "top_xtal", 13), - GATE_INFRA3(CLK_INFRA_USB_XHCI, "infra_usb_xhci", "usb_xhci_sel", 14), - GATE_INFRA3(CLK_INFRA_USB_XHCI_CK_P1, "infra_usb_xhci_ck_p1", - "usb_xhci_p1_sel", 15), - GATE_INFRA3(CLK_INFRA_PCIE_GFMUX_TL_P0, "infra_pcie_gfmux_tl_ck_p0", - "infra_pcie_gfmux_tl_o_p0_sel", 20), - GATE_INFRA3(CLK_INFRA_PCIE_GFMUX_TL_P1, "infra_pcie_gfmux_tl_ck_p1", - "infra_pcie_gfmux_tl_o_p1_sel", 21), - GATE_INFRA3(CLK_INFRA_PCIE_GFMUX_TL_P2, "infra_pcie_gfmux_tl_ck_p2", - "infra_pcie_gfmux_tl_o_p2_sel", 22), - GATE_INFRA3(CLK_INFRA_PCIE_GFMUX_TL_P3, "infra_pcie_gfmux_tl_ck_p3", - "infra_pcie_gfmux_tl_o_p3_sel", 23), - GATE_INFRA3(CLK_INFRA_PCIE_PIPE_P0, "infra_pcie_pipe_ck_p0", - "top_xtal", 24), - GATE_INFRA3(CLK_INFRA_PCIE_PIPE_P1, "infra_pcie_pipe_ck_p1", - "top_xtal", 25), - GATE_INFRA3(CLK_INFRA_PCIE_PIPE_P2, "infra_pcie_pipe_ck_p2", - "top_xtal", 26), - GATE_INFRA3(CLK_INFRA_PCIE_PIPE_P3, "infra_pcie_pipe_ck_p3", - "top_xtal", 27), - GATE_INFRA3(CLK_INFRA_133M_PCIE_CK_P0, "infra_133m_pcie_ck_p0", - "sysaxi_sel", 28), - GATE_INFRA3(CLK_INFRA_133M_PCIE_CK_P1, "infra_133m_pcie_ck_p1", - "sysaxi_sel", 29), - GATE_INFRA3(CLK_INFRA_133M_PCIE_CK_P2, "infra_133m_pcie_ck_p2", - "sysaxi_sel", 30), - GATE_INFRA3(CLK_INFRA_133M_PCIE_CK_P3, "infra_133m_pcie_ck_p3", - "sysaxi_sel", 31), -}; - -static int clk_mt7988_infracfg_probe(struct platform_device *pdev) -{ - struct clk_onecell_data *clk_data; - struct device_node *node = pdev->dev.of_node; - int r; - void __iomem *base; - int nr = ARRAY_SIZE(infra_muxes) + ARRAY_SIZE(infra_clks); - - base = of_iomap(node, 0); - if (!base) { - pr_err("%s(): ioremap failed\n", __func__); - return -ENOMEM; - } - - clk_data = mtk_alloc_clk_data(nr); - - if (!clk_data) - return -ENOMEM; - - mtk_clk_register_muxes(infra_muxes, ARRAY_SIZE(infra_muxes), node, - &mt7988_clk_lock, clk_data); - - mtk_clk_register_gates(node, infra_clks, ARRAY_SIZE(infra_clks), - clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - if (r) { - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); - goto free_infracfg_data; - } - return r; - -free_infracfg_data: - mtk_free_clk_data(clk_data); - return r; -} - -static const struct of_device_id of_match_clk_mt7988_infracfg[] = { - { - .compatible = "mediatek,mt7988-infracfg", - }, - {} -}; - -static struct platform_driver clk_mt7988_infracfg_drv = { - .probe = clk_mt7988_infracfg_probe, - .driver = { - .name = "clk-mt7988-infracfg", - .of_match_table = of_match_clk_mt7988_infracfg, - }, -}; -builtin_platform_driver(clk_mt7988_infracfg_drv); diff --git a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7988-topckgen.c b/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7988-topckgen.c deleted file mode 100644 index 917302b6df..0000000000 --- a/target/linux/mediatek/files-5.15/drivers/clk/mediatek/clk-mt7988-topckgen.c +++ /dev/null @@ -1,522 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Copyright (c) 2023 MediaTek Inc. - * Author: Sam Shih - * Author: Xiufeng Li - */ - -#include -#include -#include -#include -#include -#include "clk-mtk.h" -#include "clk-gate.h" -#include "clk-mux.h" -#include - -static DEFINE_SPINLOCK(mt7988_clk_lock); - -static const struct mtk_fixed_clk top_fixed_clks[] = { - FIXED_CLK(CLK_TOP_XTAL, "top_xtal", "clkxtal", 40000000), -}; - -static const struct mtk_fixed_factor top_divs[] = { - FACTOR(CLK_TOP_XTAL_D2, "top_xtal_d2", "top_xtal", 1, 2), - FACTOR(CLK_TOP_RTC_32K, "top_rtc_32k", "top_xtal", 1, 1250), - FACTOR(CLK_TOP_RTC_32P7K, "top_rtc_32p7k", "top_xtal", 1, 1220), - FACTOR(CLK_TOP_MPLL_D2, "mpll_d2", "mpll", 1, 2), - FACTOR(CLK_TOP_MPLL_D3_D2, "mpll_d3_d2", "mpll", 1, 2), - FACTOR(CLK_TOP_MPLL_D4, "mpll_d4", "mpll", 1, 4), - FACTOR(CLK_TOP_MPLL_D8, "mpll_d8", "mpll", 1, 8), - FACTOR(CLK_TOP_MPLL_D8_D2, "mpll_d8_d2", "mpll", 1, 16), - FACTOR(CLK_TOP_MMPLL_D2, "mmpll_d2", "mmpll", 1, 2), - FACTOR(CLK_TOP_MMPLL_D3_D5, "mmpll_d3_d5", "mmpll", 1, 15), - FACTOR(CLK_TOP_MMPLL_D4, "mmpll_d4", "mmpll", 1, 4), - FACTOR(CLK_TOP_MMPLL_D6_D2, "mmpll_d6_d2", "mmpll", 1, 12), - FACTOR(CLK_TOP_MMPLL_D8, "mmpll_d8", "mmpll", 1, 8), - FACTOR(CLK_TOP_APLL2_D4, "apll2_d4", "apll2", 1, 4), - FACTOR(CLK_TOP_NET1PLL_D4, "net1pll_d4", "net1pll", 1, 4), - FACTOR(CLK_TOP_NET1PLL_D5, "net1pll_d5", "net1pll", 1, 5), - FACTOR(CLK_TOP_NET1PLL_D5_D2, "net1pll_d5_d2", "net1pll", 1, 10), - FACTOR(CLK_TOP_NET1PLL_D5_D4, "net1pll_d5_d4", "net1pll", 1, 20), - FACTOR(CLK_TOP_NET1PLL_D8, "net1pll_d8", "net1pll", 1, 8), - FACTOR(CLK_TOP_NET1PLL_D8_D2, "net1pll_d8_d2", "net1pll", 1, 16), - FACTOR(CLK_TOP_NET1PLL_D8_D4, "net1pll_d8_d4", "net1pll", 1, 32), - FACTOR(CLK_TOP_NET1PLL_D8_D8, "net1pll_d8_d8", "net1pll", 1, 64), - FACTOR(CLK_TOP_NET1PLL_D8_D16, "net1pll_d8_d16", "net1pll", 1, 128), - FACTOR(CLK_TOP_NET2PLL_D2, "net2pll_d2", "net2pll", 1, 2), - FACTOR(CLK_TOP_NET2PLL_D4, "net2pll_d4", "net2pll", 1, 4), - FACTOR(CLK_TOP_NET2PLL_D4_D4, "net2pll_d4_d4", "net2pll", 1, 16), - FACTOR(CLK_TOP_NET2PLL_D4_D8, "net2pll_d4_d8", "net2pll", 1, 32), - FACTOR(CLK_TOP_NET2PLL_D6, "net2pll_d6", "net2pll", 1, 6), - FACTOR(CLK_TOP_NET2PLL_D8, "net2pll_d8", "net2pll", 1, 8), -}; - -static const char *const netsys_parents[] = { "top_xtal", "net2pll_d2", - "mmpll_d2" }; - -static const char *const netsys_500m_parents[] = { "top_xtal", "net1pll_d5", - "net1pll_d5_d2" }; - -static const char *const netsys_2x_parents[] = { "top_xtal", "net2pll", - "mmpll" }; - -static const char *const netsys_gsw_parents[] = { "top_xtal", "net1pll_d4", - "net1pll_d5" }; - -static const char *const eth_gmii_parents[] = { "top_xtal", "net1pll_d5_d4" }; - -static const char *const netsys_mcu_parents[] = { "top_xtal", "net2pll", - "mmpll", "net1pll_d4", - "net1pll_d5", "mpll" }; - -static const char *const eip197_parents[] = { "top_xtal", "netsyspll", - "net2pll", "mmpll", - "net1pll_d4", "net1pll_d5" }; - -static const char *const axi_infra_parents[] = { "top_xtal", "net1pll_d8_d2" }; - -static const char *const uart_parents[] = { "top_xtal", "mpll_d8", - "mpll_d8_d2" }; - -static const char *const emmc_250m_parents[] = { "top_xtal", "net1pll_d5_d2", - "mmpll_d4" }; - -static const char *const emmc_400m_parents[] = { "top_xtal", "msdcpll", - "mmpll_d2", "mpll_d2", - "mmpll_d4", "net1pll_d8_d2" }; - -static const char *const spi_parents[] = { "top_xtal", "mpll_d2", - "mmpll_d4", "net1pll_d8_d2", - "net2pll_d6", "net1pll_d5_d4", - "mpll_d4", "net1pll_d8_d4" }; - -static const char *const nfi1x_parents[] = { "top_xtal", "mmpll_d4", - "net1pll_d8_d2", "net2pll_d6", - "mpll_d4", "mmpll_d8", - "net1pll_d8_d4", "mpll_d8" }; - -static const char *const spinfi_parents[] = { "top_xtal_d2", "top_xtal", - "net1pll_d5_d4", "mpll_d4", - "mmpll_d8", "net1pll_d8_d4", - "mmpll_d6_d2", "mpll_d8" }; - -static const char *const pwm_parents[] = { "top_xtal", "net1pll_d8_d2", - "net1pll_d5_d4", "mpll_d4", - "mpll_d8_d2", "top_rtc_32k" }; - -static const char *const i2c_parents[] = { "top_xtal", "net1pll_d5_d4", - "mpll_d4", "net1pll_d8_d4" }; - -static const char *const pcie_mbist_250m_parents[] = { "top_xtal", - "net1pll_d5_d2" }; - -static const char *const pextp_tl_ck_parents[] = { "top_xtal", "net2pll_d6", - "mmpll_d8", "mpll_d8_d2", - "top_rtc_32k" }; - -static const char *const usb_frmcnt_parents[] = { "top_xtal", "mmpll_d3_d5" }; - -static const char *const aud_parents[] = { "top_xtal", "apll2" }; - -static const char *const a1sys_parents[] = { "top_xtal", "apll2_d4" }; - -static const char *const aud_l_parents[] = { "top_xtal", "apll2", - "mpll_d8_d2" }; - -static const char *const sspxtp_parents[] = { "top_xtal_d2", "mpll_d8_d2" }; - -static const char *const usxgmii_sbus_0_parents[] = { "top_xtal", - "net1pll_d8_d4" }; - -static const char *const sgm_0_parents[] = { "top_xtal", "sgmpll" }; - -static const char *const sysapb_parents[] = { "top_xtal", "mpll_d3_d2" }; - -static const char *const eth_refck_50m_parents[] = { "top_xtal", - "net2pll_d4_d4" }; - -static const char *const eth_sys_200m_parents[] = { "top_xtal", "net2pll_d4" }; - -static const char *const eth_xgmii_parents[] = { "top_xtal_d2", - "net1pll_d8_d8", - "net1pll_d8_d16" }; - -static const char *const bus_tops_parents[] = { "top_xtal", "net1pll_d5", - "net2pll_d2" }; - -static const char *const npu_tops_parents[] = { "top_xtal", "net2pll" }; - -static const char *const dramc_md32_parents[] = { "top_xtal", "mpll_d2", - "wedmcupll" }; - -static const char *const da_xtp_glb_p0_parents[] = { "top_xtal", - "net2pll_d8" }; - -static const char *const mcusys_backup_625m_parents[] = { "top_xtal", - "net1pll_d4" }; - -static const char *const macsec_parents[] = { "top_xtal", "sgmpll", - "net1pll_d8" }; - -static const char *const netsys_tops_400m_parents[] = { "top_xtal", - "net2pll_d2" }; - -static const char *const eth_mii_parents[] = { "top_xtal_d2", - "net2pll_d4_d8" }; - -static const struct mtk_mux top_muxes[] = { - /* CLK_CFG_0 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_SEL, "netsys_sel", netsys_parents, - 0x000, 0x004, 0x008, 0, 2, 7, 0x1c0, 0), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_500M_SEL, "netsys_500m_sel", - netsys_500m_parents, 0x000, 0x004, 0x008, 8, 2, - 15, 0x1C0, 1), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_2X_SEL, "netsys_2x_sel", - netsys_2x_parents, 0x000, 0x004, 0x008, 16, 2, 23, - 0x1C0, 2), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_GSW_SEL, "netsys_gsw_sel", - netsys_gsw_parents, 0x000, 0x004, 0x008, 24, 2, - 31, 0x1C0, 3), - /* CLK_CFG_1 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_ETH_GMII_SEL, "eth_gmii_sel", - eth_gmii_parents, 0x010, 0x014, 0x018, 0, 1, 7, - 0x1C0, 4), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_MCU_SEL, "netsys_mcu_sel", - netsys_mcu_parents, 0x010, 0x014, 0x018, 8, 3, 15, - 0x1C0, 5), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_PAO_2X_SEL, "netsys_pao_2x_sel", - netsys_mcu_parents, 0x010, 0x014, 0x018, 16, 3, - 23, 0x1C0, 6), - MUX_GATE_CLR_SET_UPD(CLK_TOP_EIP197_SEL, "eip197_sel", eip197_parents, - 0x010, 0x014, 0x018, 24, 3, 31, 0x1c0, 7), - /* CLK_CFG_2 */ - MUX_GATE_CLR_SET_UPD_FLAGS(CLK_TOP_AXI_INFRA_SEL, "axi_infra_sel", - axi_infra_parents, 0x020, 0x024, 0x028, 0, - 1, 7, 0x1C0, 8, CLK_IS_CRITICAL), - MUX_GATE_CLR_SET_UPD(CLK_TOP_UART_SEL, "uart_sel", uart_parents, 0x020, - 0x024, 0x028, 8, 2, 15, 0x1c0, 9), - MUX_GATE_CLR_SET_UPD(CLK_TOP_EMMC_250M_SEL, "emmc_250m_sel", - emmc_250m_parents, 0x020, 0x024, 0x028, 16, 2, 23, - 0x1C0, 10), - MUX_GATE_CLR_SET_UPD(CLK_TOP_EMMC_400M_SEL, "emmc_400m_sel", - emmc_400m_parents, 0x020, 0x024, 0x028, 24, 3, 31, - 0x1C0, 11), - /* CLK_CFG_3 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_SPI_SEL, "spi_sel", spi_parents, 0x030, - 0x034, 0x038, 0, 3, 7, 0x1c0, 12), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SPIM_MST_SEL, "spim_mst_sel", spi_parents, - 0x030, 0x034, 0x038, 8, 3, 15, 0x1c0, 13), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NFI1X_SEL, "nfi1x_sel", nfi1x_parents, - 0x030, 0x034, 0x038, 16, 3, 23, 0x1c0, 14), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SPINFI_SEL, "spinfi_sel", spinfi_parents, - 0x030, 0x034, 0x038, 24, 3, 31, 0x1c0, 15), - /* CLK_CFG_4 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_PWM_SEL, "pwm_sel", pwm_parents, 0x040, - 0x044, 0x048, 0, 3, 7, 0x1c0, 16), - MUX_GATE_CLR_SET_UPD(CLK_TOP_I2C_SEL, "i2c_sel", i2c_parents, 0x040, - 0x044, 0x048, 8, 2, 15, 0x1c0, 17), - MUX_GATE_CLR_SET_UPD(CLK_TOP_PCIE_MBIST_250M_SEL, - "pcie_mbist_250m_sel", pcie_mbist_250m_parents, - 0x040, 0x044, 0x048, 16, 1, 23, 0x1C0, 18), - MUX_GATE_CLR_SET_UPD(CLK_TOP_PEXTP_TL_SEL, "pextp_tl_sel", - pextp_tl_ck_parents, 0x040, 0x044, 0x048, 24, 3, - 31, 0x1C0, 19), - /* CLK_CFG_5 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_PEXTP_TL_P1_SEL, "pextp_tl_p1_sel", - pextp_tl_ck_parents, 0x050, 0x054, 0x058, 0, 3, 7, - 0x1C0, 20), - MUX_GATE_CLR_SET_UPD(CLK_TOP_PEXTP_TL_P2_SEL, "pextp_tl_p2_sel", - pextp_tl_ck_parents, 0x050, 0x054, 0x058, 8, 3, - 15, 0x1C0, 21), - MUX_GATE_CLR_SET_UPD(CLK_TOP_PEXTP_TL_P3_SEL, "pextp_tl_p3_sel", - pextp_tl_ck_parents, 0x050, 0x054, 0x058, 16, 3, - 23, 0x1C0, 22), - MUX_GATE_CLR_SET_UPD(CLK_TOP_USB_SYS_SEL, "usb_sys_sel", - eth_gmii_parents, 0x050, 0x054, 0x058, 24, 1, 31, - 0x1C0, 23), - /* CLK_CFG_6 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_USB_SYS_P1_SEL, "usb_sys_p1_sel", - eth_gmii_parents, 0x060, 0x064, 0x068, 0, 1, 7, - 0x1C0, 24), - MUX_GATE_CLR_SET_UPD(CLK_TOP_USB_XHCI_SEL, "usb_xhci_sel", - eth_gmii_parents, 0x060, 0x064, 0x068, 8, 1, 15, - 0x1C0, 25), - MUX_GATE_CLR_SET_UPD(CLK_TOP_USB_XHCI_P1_SEL, "usb_xhci_p1_sel", - eth_gmii_parents, 0x060, 0x064, 0x068, 16, 1, 23, - 0x1C0, 26), - MUX_GATE_CLR_SET_UPD(CLK_TOP_USB_FRMCNT_SEL, "usb_frmcnt_sel", - usb_frmcnt_parents, 0x060, 0x064, 0x068, 24, 1, - 31, 0x1C0, 27), - /* CLK_CFG_7 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_USB_FRMCNT_P1_SEL, "usb_frmcnt_p1_sel", - usb_frmcnt_parents, 0x070, 0x074, 0x078, 0, 1, 7, - 0x1C0, 28), - MUX_GATE_CLR_SET_UPD(CLK_TOP_AUD_SEL, "aud_sel", aud_parents, 0x070, - 0x074, 0x078, 8, 1, 15, 0x1c0, 29), - MUX_GATE_CLR_SET_UPD(CLK_TOP_A1SYS_SEL, "a1sys_sel", a1sys_parents, - 0x070, 0x074, 0x078, 16, 1, 23, 0x1c0, 30), - MUX_GATE_CLR_SET_UPD(CLK_TOP_AUD_L_SEL, "aud_l_sel", aud_l_parents, - 0x070, 0x074, 0x078, 24, 2, 31, 0x1c4, 0), - /* CLK_CFG_8 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_A_TUNER_SEL, "a_tuner_sel", a1sys_parents, - 0x080, 0x084, 0x088, 0, 1, 7, 0x1c4, 1), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SSPXTP_SEL, "sspxtp_sel", sspxtp_parents, - 0x080, 0x084, 0x088, 8, 1, 15, 0x1c4, 2), - MUX_GATE_CLR_SET_UPD(CLK_TOP_USB_PHY_SEL, "usb_phy_sel", - sspxtp_parents, 0x080, 0x084, 0x088, 16, 1, 23, - 0x1c4, 3), - MUX_GATE_CLR_SET_UPD(CLK_TOP_USXGMII_SBUS_0_SEL, "usxgmii_sbus_0_sel", - usxgmii_sbus_0_parents, 0x080, 0x084, 0x088, 24, - 1, 31, 0x1C4, 4), - /* CLK_CFG_9 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_USXGMII_SBUS_1_SEL, "usxgmii_sbus_1_sel", - usxgmii_sbus_0_parents, 0x090, 0x094, 0x098, 0, 1, - 7, 0x1C4, 5), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SGM_0_SEL, "sgm_0_sel", sgm_0_parents, - 0x090, 0x094, 0x098, 8, 1, 15, 0x1c4, 6), - MUX_GATE_CLR_SET_UPD_FLAGS(CLK_TOP_SGM_SBUS_0_SEL, "sgm_sbus_0_sel", - usxgmii_sbus_0_parents, 0x090, 0x094, 0x098, - 16, 1, 23, 0x1C4, 7, CLK_IS_CRITICAL), - MUX_GATE_CLR_SET_UPD(CLK_TOP_SGM_1_SEL, "sgm_1_sel", sgm_0_parents, - 0x090, 0x094, 0x098, 24, 1, 31, 0x1c4, 8), - /* CLK_CFG_10 */ - MUX_GATE_CLR_SET_UPD_FLAGS(CLK_TOP_SGM_SBUS_1_SEL, "sgm_sbus_1_sel", - usxgmii_sbus_0_parents, 0x0a0, 0x0a4, 0x0a8, - 0, 1, 7, 0x1C4, 9, CLK_IS_CRITICAL), - MUX_GATE_CLR_SET_UPD(CLK_TOP_XFI_PHY_0_XTAL_SEL, "xfi_phy_0_xtal_sel", - sspxtp_parents, 0x0a0, 0x0a4, 0x0a8, 8, 1, 15, - 0x1C4, 10), - MUX_GATE_CLR_SET_UPD(CLK_TOP_XFI_PHY_1_XTAL_SEL, "xfi_phy_1_xtal_sel", - sspxtp_parents, 0x0a0, 0x0a4, 0x0a8, 16, 1, 23, - 0x1C4, 11), - /* CLK_CFG_11 */ - MUX_GATE_CLR_SET_UPD_FLAGS(CLK_TOP_SYSAXI_SEL, "sysaxi_sel", - axi_infra_parents, 0x0a0, 0x0a4, 0x0a8, 24, - 1, 31, 0x1C4, 12, CLK_IS_CRITICAL), - MUX_GATE_CLR_SET_UPD_FLAGS(CLK_TOP_SYSAPB_SEL, "sysapb_sel", - sysapb_parents, 0x0b0, 0x0b4, 0x0b8, 0, 1, - 7, 0x1c4, 13, CLK_IS_CRITICAL), - MUX_GATE_CLR_SET_UPD(CLK_TOP_ETH_REFCK_50M_SEL, "eth_refck_50m_sel", - eth_refck_50m_parents, 0x0b0, 0x0b4, 0x0b8, 8, 1, - 15, 0x1C4, 14), - MUX_GATE_CLR_SET_UPD(CLK_TOP_ETH_SYS_200M_SEL, "eth_sys_200m_sel", - eth_sys_200m_parents, 0x0b0, 0x0b4, 0x0b8, 16, 1, - 23, 0x1C4, 15), - MUX_GATE_CLR_SET_UPD(CLK_TOP_ETH_SYS_SEL, "eth_sys_sel", - pcie_mbist_250m_parents, 0x0b0, 0x0b4, 0x0b8, 24, - 1, 31, 0x1C4, 16), - /* CLK_CFG_12 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_ETH_XGMII_SEL, "eth_xgmii_sel", - eth_xgmii_parents, 0x0c0, 0x0c4, 0x0c8, 0, 2, 7, - 0x1C4, 17), - MUX_GATE_CLR_SET_UPD(CLK_TOP_BUS_TOPS_SEL, "bus_tops_sel", - bus_tops_parents, 0x0c0, 0x0c4, 0x0c8, 8, 2, 15, - 0x1C4, 18), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NPU_TOPS_SEL, "npu_tops_sel", - npu_tops_parents, 0x0c0, 0x0c4, 0x0c8, 16, 1, 23, - 0x1C4, 19), - MUX_GATE_CLR_SET_UPD_FLAGS(CLK_TOP_DRAMC_SEL, "dramc_sel", - sspxtp_parents, 0x0c0, 0x0c4, 0x0c8, 24, 1, - 31, 0x1C4, 20, CLK_IS_CRITICAL), - /* CLK_CFG_13 */ - MUX_GATE_CLR_SET_UPD_FLAGS(CLK_TOP_DRAMC_MD32_SEL, "dramc_md32_sel", - dramc_md32_parents, 0x0d0, 0x0d4, 0x0d8, 0, - 2, 7, 0x1C4, 21, CLK_IS_CRITICAL), - MUX_GATE_CLR_SET_UPD_FLAGS( - CLK_TOP_INFRA_F26M_SEL, "csw_infra_f26m_sel", sspxtp_parents, - 0x0d0, 0x0d4, 0x0d8, 8, 1, 15, 0x1C4, 22, CLK_IS_CRITICAL), - MUX_GATE_CLR_SET_UPD(CLK_TOP_PEXTP_P0_SEL, "pextp_p0_sel", - sspxtp_parents, 0x0d0, 0x0d4, 0x0d8, 16, 1, 23, - 0x1C4, 23), - MUX_GATE_CLR_SET_UPD(CLK_TOP_PEXTP_P1_SEL, "pextp_p1_sel", - sspxtp_parents, 0x0d0, 0x0d4, 0x0d8, 24, 1, 31, - 0x1C4, 24), - /* CLK_CFG_14 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_PEXTP_P2_SEL, "pextp_p2_sel", - sspxtp_parents, 0x0e0, 0x0e4, 0x0e8, 0, 1, 7, - 0x1C4, 25), - MUX_GATE_CLR_SET_UPD(CLK_TOP_PEXTP_P3_SEL, "pextp_p3_sel", - sspxtp_parents, 0x0e0, 0x0e4, 0x0e8, 8, 1, 15, - 0x1C4, 26), - MUX_GATE_CLR_SET_UPD(CLK_TOP_DA_XTP_GLB_P0_SEL, "da_xtp_glb_p0_sel", - da_xtp_glb_p0_parents, 0x0e0, 0x0e4, 0x0e8, 16, 1, - 23, 0x1C4, 27), - MUX_GATE_CLR_SET_UPD(CLK_TOP_DA_XTP_GLB_P1_SEL, "da_xtp_glb_p1_sel", - da_xtp_glb_p0_parents, 0x0e0, 0x0e4, 0x0e8, 24, 1, - 31, 0x1C4, 28), - /* CLK_CFG_15 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_DA_XTP_GLB_P2_SEL, "da_xtp_glb_p2_sel", - da_xtp_glb_p0_parents, 0x0f0, 0x0f4, 0x0f8, 0, 1, - 7, 0x1C4, 29), - MUX_GATE_CLR_SET_UPD(CLK_TOP_DA_XTP_GLB_P3_SEL, "da_xtp_glb_p3_sel", - da_xtp_glb_p0_parents, 0x0f0, 0x0f4, 0x0f8, 8, 1, - 15, 0x1C4, 30), - MUX_GATE_CLR_SET_UPD(CLK_TOP_CKM_SEL, "ckm_sel", sspxtp_parents, 0x0F0, - 0x0f4, 0x0f8, 16, 1, 23, 0x1c8, 0), - MUX_GATE_CLR_SET_UPD(CLK_TOP_DA_SEL, "da_sel", sspxtp_parents, 0x0f0, - 0x0f4, 0x0f8, 24, 1, 31, 0x1C8, 1), - /* CLK_CFG_16 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_PEXTP_SEL, "pextp_sel", sspxtp_parents, - 0x0100, 0x104, 0x108, 0, 1, 7, 0x1c8, 2), - MUX_GATE_CLR_SET_UPD(CLK_TOP_TOPS_P2_26M_SEL, "tops_p2_26m_sel", - sspxtp_parents, 0x0100, 0x104, 0x108, 8, 1, 15, - 0x1C8, 3), - MUX_GATE_CLR_SET_UPD(CLK_TOP_MCUSYS_BACKUP_625M_SEL, - "mcusys_backup_625m_sel", - mcusys_backup_625m_parents, 0x0100, 0x104, 0x108, - 16, 1, 23, 0x1C8, 4), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_SYNC_250M_SEL, - "netsys_sync_250m_sel", pcie_mbist_250m_parents, - 0x0100, 0x104, 0x108, 24, 1, 31, 0x1c8, 5), - /* CLK_CFG_17 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_MACSEC_SEL, "macsec_sel", macsec_parents, - 0x0110, 0x114, 0x118, 0, 2, 7, 0x1c8, 6), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_TOPS_400M_SEL, - "netsys_tops_400m_sel", netsys_tops_400m_parents, - 0x0110, 0x114, 0x118, 8, 1, 15, 0x1c8, 7), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_PPEFB_250M_SEL, - "netsys_ppefb_250m_sel", pcie_mbist_250m_parents, - 0x0110, 0x114, 0x118, 16, 1, 23, 0x1c8, 8), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NETSYS_WARP_SEL, "netsys_warp_sel", - netsys_parents, 0x0110, 0x114, 0x118, 24, 2, 31, - 0x1C8, 9), - /* CLK_CFG_18 */ - MUX_GATE_CLR_SET_UPD(CLK_TOP_ETH_MII_SEL, "eth_mii_sel", - eth_mii_parents, 0x0120, 0x124, 0x128, 0, 1, 7, - 0x1c8, 10), - MUX_GATE_CLR_SET_UPD(CLK_TOP_NPU_SEL, "ck_npu_sel", netsys_2x_parents, - 0x0120, 0x124, 0x128, 8, 2, 15, 0x1c8, 11), -}; - -static const struct mtk_composite top_aud_divs[] = { - DIV_GATE(CLK_TOP_AUD_I2S_M, "aud_i2s_m", "aud_sel", 0x0420, 0, 0x0420, - 8, 8), -}; - -static int clk_mt7988_topckgen_probe(struct platform_device *pdev) -{ - struct clk_onecell_data *clk_data; - struct device_node *node = pdev->dev.of_node; - int r; - void __iomem *base; - int nr = ARRAY_SIZE(top_fixed_clks) + ARRAY_SIZE(top_divs) + - ARRAY_SIZE(top_muxes) + ARRAY_SIZE(top_aud_divs); - - base = of_iomap(node, 0); - if (!base) { - pr_err("%s(): ioremap failed\n", __func__); - return -ENOMEM; - } - - clk_data = mtk_alloc_clk_data(nr); - if (!clk_data) - return -ENOMEM; - - mtk_clk_register_fixed_clks(top_fixed_clks, ARRAY_SIZE(top_fixed_clks), - clk_data); - - mtk_clk_register_factors(top_divs, ARRAY_SIZE(top_divs), clk_data); - - mtk_clk_register_muxes(top_muxes, ARRAY_SIZE(top_muxes), node, - &mt7988_clk_lock, clk_data); - - mtk_clk_register_composites(top_aud_divs, ARRAY_SIZE(top_aud_divs), - base, &mt7988_clk_lock, clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - - if (r) { - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); - goto free_topckgen_data; - } - return r; - -free_topckgen_data: - mtk_free_clk_data(clk_data); - return r; -} - -static const char *const mcu_bus_div_parents[] = { "top_xtal", "ccipll2_b", - "net1pll_d4" }; - -static const char *const mcu_arm_div_parents[] = { "top_xtal", "arm_b", - "net1pll_d4" }; - -static struct mtk_composite mcu_muxes[] = { - /* bus_pll_divider_cfg */ - MUX_GATE_FLAGS(CLK_MCU_BUS_DIV_SEL, "mcu_bus_div_sel", - mcu_bus_div_parents, 0x7C0, 9, 2, -1, CLK_IS_CRITICAL), - /* mp2_pll_divider_cfg */ - MUX_GATE_FLAGS(CLK_MCU_ARM_DIV_SEL, "mcu_arm_div_sel", - mcu_arm_div_parents, 0x7A8, 9, 2, -1, CLK_IS_CRITICAL), -}; - -static int clk_mt7988_mcusys_probe(struct platform_device *pdev) -{ - struct clk_onecell_data *clk_data; - struct device_node *node = pdev->dev.of_node; - int r; - void __iomem *base; - int nr = ARRAY_SIZE(mcu_muxes); - - base = of_iomap(node, 0); - if (!base) { - pr_err("%s(): ioremap failed\n", __func__); - return -ENOMEM; - } - - clk_data = mtk_alloc_clk_data(nr); - if (!clk_data) - return -ENOMEM; - - mtk_clk_register_composites(mcu_muxes, ARRAY_SIZE(mcu_muxes), base, - &mt7988_clk_lock, clk_data); - - r = of_clk_add_provider(node, of_clk_src_onecell_get, clk_data); - - if (r) { - pr_err("%s(): could not register clock provider: %d\n", - __func__, r); - goto free_mcusys_data; - } - return r; - -free_mcusys_data: - mtk_free_clk_data(clk_data); - return r; -} - -static const struct of_device_id of_match_clk_mt7988_topckgen[] = { - { - .compatible = "mediatek,mt7988-topckgen", - }, - {} -}; - -static struct platform_driver clk_mt7988_topckgen_drv = { - .probe = clk_mt7988_topckgen_probe, - .driver = { - .name = "clk-mt7988-topckgen", - .of_match_table = of_match_clk_mt7988_topckgen, - }, -}; -builtin_platform_driver(clk_mt7988_topckgen_drv); - -static const struct of_device_id of_match_clk_mt7988_mcusys[] = { - { - .compatible = "mediatek,mt7988-mcusys", - }, - {} -}; - -static struct platform_driver clk_mt7988_mcusys_drv = { - .probe = clk_mt7988_mcusys_probe, - .driver = { - .name = "clk-mt7988-mcusys", - .of_match_table = of_match_clk_mt7988_mcusys, - }, -}; -builtin_platform_driver(clk_mt7988_mcusys_drv); \ No newline at end of file diff --git a/target/linux/mediatek/files-5.15/drivers/net/phy/mediatek-2p5ge.c b/target/linux/mediatek/files-5.15/drivers/net/phy/mediatek-2p5ge.c deleted file mode 100644 index c12e6b8eb6..0000000000 --- a/target/linux/mediatek/files-5.15/drivers/net/phy/mediatek-2p5ge.c +++ /dev/null @@ -1,262 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -#include -#include -#include -#include -#include -#include -#include -#include - -#define MEDAITEK_2P5GE_PHY_DMB_FW "mediatek/mediatek-2p5ge-phy-dmb.bin" -#define MEDIATEK_2P5GE_PHY_PMB_FW "mediatek/mediatek-2p5ge-phy-pmb.bin" - -#define MD32_EN_CFG 0x18 -#define MD32_EN BIT(0) - -#define BASE100T_STATUS_EXTEND 0x10 -#define BASE1000T_STATUS_EXTEND 0x11 -#define EXTEND_CTRL_AND_STATUS 0x16 - -#define PHY_AUX_CTRL_STATUS 0x1d -#define PHY_AUX_DPX_MASK GENMASK(5, 5) -#define PHY_AUX_SPEED_MASK GENMASK(4, 2) - -/* Registers on MDIO_MMD_VEND1 */ -#define MTK_PHY_LINK_STATUS_MISC 0xa2 -#define MTK_PHY_FDX_ENABLE BIT(5) - -/* Registers on MDIO_MMD_VEND2 */ -#define MTK_PHY_LED0_ON_CTRL 0x24 -#define MTK_PHY_LED0_ON_LINK1000 BIT(0) -#define MTK_PHY_LED0_ON_LINK100 BIT(1) -#define MTK_PHY_LED0_ON_LINK10 BIT(2) -#define MTK_PHY_LED0_ON_LINK2500 BIT(7) -#define MTK_PHY_LED0_POLARITY BIT(14) - -#define MTK_PHY_LED1_ON_CTRL 0x26 -#define MTK_PHY_LED1_ON_FDX BIT(4) -#define MTK_PHY_LED1_ON_HDX BIT(5) -#define MTK_PHY_LED1_POLARITY BIT(14) - -enum { - PHY_AUX_SPD_10 = 0, - PHY_AUX_SPD_100, - PHY_AUX_SPD_1000, - PHY_AUX_SPD_2500, -}; - -static int mt798x_2p5ge_phy_config_init(struct phy_device *phydev) -{ - int ret; - int i; - const struct firmware *fw; - struct device *dev = &phydev->mdio.dev; - struct device_node *np; - void __iomem *dmb_addr; - void __iomem *pmb_addr; - void __iomem *mcucsr_base; - u16 reg; - struct pinctrl *pinctrl; - - np = of_find_compatible_node(NULL, NULL, "mediatek,2p5gphy-fw"); - if (!np) - return -ENOENT; - - dmb_addr = of_iomap(np, 0); - if (!dmb_addr) - return -ENOMEM; - pmb_addr = of_iomap(np, 1); - if (!pmb_addr) - return -ENOMEM; - mcucsr_base = of_iomap(np, 2); - if (!mcucsr_base) - return -ENOMEM; - - ret = request_firmware(&fw, MEDAITEK_2P5GE_PHY_DMB_FW, dev); - if (ret) { - dev_err(dev, "failed to load firmware: %s, ret: %d\n", - MEDAITEK_2P5GE_PHY_DMB_FW, ret); - return ret; - } - for (i = 0; i < fw->size - 1; i += 4) - writel(*((uint32_t *)(fw->data + i)), dmb_addr + i); - release_firmware(fw); - - ret = request_firmware(&fw, MEDIATEK_2P5GE_PHY_PMB_FW, dev); - if (ret) { - dev_err(dev, "failed to load firmware: %s, ret: %d\n", - MEDIATEK_2P5GE_PHY_PMB_FW, ret); - return ret; - } - for (i = 0; i < fw->size - 1; i += 4) - writel(*((uint32_t *)(fw->data + i)), pmb_addr + i); - release_firmware(fw); - - reg = readw(mcucsr_base + MD32_EN_CFG); - writew(reg | MD32_EN, mcucsr_base + MD32_EN_CFG); - dev_dbg(dev, "Firmware loading/trigger ok.\n"); - - /* Setup LED */ - phy_clear_bits_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED0_ON_CTRL, - MTK_PHY_LED0_POLARITY); - - phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED0_ON_CTRL, - MTK_PHY_LED0_ON_LINK10 | - MTK_PHY_LED0_ON_LINK100 | - MTK_PHY_LED0_ON_LINK1000 | - MTK_PHY_LED0_ON_LINK2500); - - phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED1_ON_CTRL, - MTK_PHY_LED1_ON_FDX | MTK_PHY_LED1_ON_HDX); - - pinctrl = devm_pinctrl_get_select(&phydev->mdio.dev, "i2p5gbe-led"); - if (IS_ERR(pinctrl)) { - dev_err(&phydev->mdio.dev, "Fail to set LED pins!\n"); - return PTR_ERR(pinctrl); - } - - return 0; -} - -static int mt798x_2p5ge_phy_config_aneg(struct phy_device *phydev) -{ - bool changed = false; - u32 adv; - int ret; - - if (phydev->autoneg == AUTONEG_DISABLE) { - /* Configure half duplex with genphy_setup_forced, - * because genphy_c45_pma_setup_forced does not support. - */ - return phydev->duplex != DUPLEX_FULL - ? genphy_setup_forced(phydev) - : genphy_c45_pma_setup_forced(phydev); - } - - ret = genphy_c45_an_config_aneg(phydev); - if (ret < 0) - return ret; - if (ret > 0) - changed = true; - - adv = linkmode_adv_to_mii_ctrl1000_t(phydev->advertising); - ret = phy_modify_changed(phydev, MII_CTRL1000, - ADVERTISE_1000FULL | ADVERTISE_1000HALF, - adv); - if (ret < 0) - return ret; - if (ret > 0) - changed = true; - - return genphy_c45_check_and_restart_aneg(phydev, changed); -} - -static int mt798x_2p5ge_phy_get_features(struct phy_device *phydev) -{ - int ret; - - ret = genphy_read_abilities(phydev); - if (ret) - return ret; - - /* We don't support HDX at MAC layer on mt798x. - * So mask phy's HDX capabilities, too. - */ - linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, - phydev->supported); - linkmode_set_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT, - phydev->supported); - linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, - phydev->supported); - linkmode_set_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, - phydev->supported); - linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->supported); - - return 0; -} - -static int mt798x_2p5ge_phy_read_status(struct phy_device *phydev) -{ - int ret; - - ret = genphy_update_link(phydev); - if (ret) - return ret; - - phydev->speed = SPEED_UNKNOWN; - phydev->duplex = DUPLEX_UNKNOWN; - phydev->pause = 0; - phydev->asym_pause = 0; - - if (!phydev->link) - return 0; - - if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete) { - ret = genphy_c45_read_lpa(phydev); - if (ret < 0) - return ret; - - /* Read the link partner's 1G advertisement */ - ret = phy_read(phydev, MII_STAT1000); - if (ret < 0) - return ret; - mii_stat1000_mod_linkmode_lpa_t(phydev->lp_advertising, ret); - } else if (phydev->autoneg == AUTONEG_DISABLE) { - linkmode_zero(phydev->lp_advertising); - } - - ret = phy_read(phydev, PHY_AUX_CTRL_STATUS); - if (ret < 0) - return ret; - - switch (FIELD_GET(PHY_AUX_SPEED_MASK, ret)) { - case PHY_AUX_SPD_10: - phydev->speed = SPEED_10; - break; - case PHY_AUX_SPD_100: - phydev->speed = SPEED_100; - break; - case PHY_AUX_SPD_1000: - phydev->speed = SPEED_1000; - break; - case PHY_AUX_SPD_2500: - phydev->speed = SPEED_2500; - phydev->duplex = DUPLEX_FULL; /* 2.5G must be FDX */ - break; - } - - ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LINK_STATUS_MISC); - if (ret < 0) - return ret; - - phydev->duplex = (ret & MTK_PHY_FDX_ENABLE) ? DUPLEX_FULL : DUPLEX_HALF; - - return 0; -} - -static struct phy_driver mtk_gephy_driver[] = { - { - PHY_ID_MATCH_EXACT(0x00339c11), - .name = "MediaTek MT798x 2.5GbE PHY", - .config_init = mt798x_2p5ge_phy_config_init, - .config_aneg = mt798x_2p5ge_phy_config_aneg, - .get_features = mt798x_2p5ge_phy_get_features, - .read_status = mt798x_2p5ge_phy_read_status, - }, -}; - -module_phy_driver(mtk_gephy_driver); - -static struct mdio_device_id __maybe_unused mtk_2p5ge_phy_tbl[] = { - { PHY_ID_MATCH_VENDOR(0x00339c00) }, - { } -}; - -MODULE_DESCRIPTION("MediaTek 2.5Gb Ethernet PHY driver"); -MODULE_AUTHOR("SkyLake Huang "); -MODULE_LICENSE("GPL"); - -MODULE_DEVICE_TABLE(mdio, mtk_2p5ge_phy_tbl); -MODULE_FIRMWARE(MEDAITEK_2P5GE_PHY_DMB_FW); -MODULE_FIRMWARE(MEDIATEK_2P5GE_PHY_PMB_FW); diff --git a/target/linux/mediatek/files-5.15/drivers/pinctrl/mediatek/pinctrl-mt7981.c b/target/linux/mediatek/files-5.15/drivers/pinctrl/mediatek/pinctrl-mt7981.c deleted file mode 100644 index 7c082dd207..0000000000 --- a/target/linux/mediatek/files-5.15/drivers/pinctrl/mediatek/pinctrl-mt7981.c +++ /dev/null @@ -1,1041 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * The MT7981 driver based on Linux generic pinctrl binding. - * - * Copyright (C) 2020 MediaTek Inc. - * Author: Sam Shih - */ - -#include "pinctrl-moore.h" - -#define MT7981_PIN(_number, _name) \ - MTK_PIN(_number, _name, 0, _number, DRV_GRP4) - -#define PIN_FIELD_BASE(_s_pin, _e_pin, _i_base, _s_addr, _x_addrs, _s_bit, _x_bits) \ - PIN_FIELD_CALC(_s_pin, _e_pin, _i_base, _s_addr, _x_addrs, _s_bit, \ - _x_bits, 32, 0) - -#define PINS_FIELD_BASE(_s_pin, _e_pin, _i_base, _s_addr, _x_addrs, _s_bit, _x_bits) \ - PIN_FIELD_CALC(_s_pin, _e_pin, _i_base, _s_addr, _x_addrs, _s_bit, \ - _x_bits, 32, 1) - -static const struct mtk_pin_field_calc mt7981_pin_mode_range[] = { - PIN_FIELD(0, 56, 0x300, 0x10, 0, 4), -}; - -static const struct mtk_pin_field_calc mt7981_pin_dir_range[] = { - PIN_FIELD(0, 56, 0x0, 0x10, 0, 1), -}; - -static const struct mtk_pin_field_calc mt7981_pin_di_range[] = { - PIN_FIELD(0, 56, 0x200, 0x10, 0, 1), -}; - -static const struct mtk_pin_field_calc mt7981_pin_do_range[] = { - PIN_FIELD(0, 56, 0x100, 0x10, 0, 1), -}; - -static const struct mtk_pin_field_calc mt7981_pin_ies_range[] = { - PIN_FIELD_BASE(0, 0, 1, 0x10, 0x10, 1, 1), - PIN_FIELD_BASE(1, 1, 1, 0x10, 0x10, 0, 1), - PIN_FIELD_BASE(2, 2, 5, 0x20, 0x10, 6, 1), - PIN_FIELD_BASE(3, 3, 4, 0x20, 0x10, 6, 1), - PIN_FIELD_BASE(4, 4, 4, 0x20, 0x10, 2, 1), - PIN_FIELD_BASE(5, 5, 4, 0x20, 0x10, 1, 1), - PIN_FIELD_BASE(6, 6, 4, 0x20, 0x10, 3, 1), - PIN_FIELD_BASE(7, 7, 4, 0x20, 0x10, 0, 1), - PIN_FIELD_BASE(8, 8, 4, 0x20, 0x10, 4, 1), - - PIN_FIELD_BASE(9, 9, 5, 0x20, 0x10, 9, 1), - PIN_FIELD_BASE(10, 10, 5, 0x20, 0x10, 8, 1), - PIN_FIELD_BASE(11, 11, 5, 0x40, 0x10, 10, 1), - PIN_FIELD_BASE(12, 12, 5, 0x20, 0x10, 7, 1), - PIN_FIELD_BASE(13, 13, 5, 0x20, 0x10, 11, 1), - - PIN_FIELD_BASE(14, 14, 4, 0x20, 0x10, 8, 1), - - PIN_FIELD_BASE(15, 15, 2, 0x20, 0x10, 0, 1), - PIN_FIELD_BASE(16, 16, 2, 0x20, 0x10, 1, 1), - PIN_FIELD_BASE(17, 17, 2, 0x20, 0x10, 5, 1), - PIN_FIELD_BASE(18, 18, 2, 0x20, 0x10, 4, 1), - PIN_FIELD_BASE(19, 19, 2, 0x20, 0x10, 2, 1), - PIN_FIELD_BASE(20, 20, 2, 0x20, 0x10, 3, 1), - PIN_FIELD_BASE(21, 21, 2, 0x20, 0x10, 6, 1), - PIN_FIELD_BASE(22, 22, 2, 0x20, 0x10, 7, 1), - PIN_FIELD_BASE(23, 23, 2, 0x20, 0x10, 10, 1), - PIN_FIELD_BASE(24, 24, 2, 0x20, 0x10, 9, 1), - PIN_FIELD_BASE(25, 25, 2, 0x20, 0x10, 8, 1), - - PIN_FIELD_BASE(26, 26, 5, 0x20, 0x10, 0, 1), - PIN_FIELD_BASE(27, 27, 5, 0x20, 0x10, 4, 1), - PIN_FIELD_BASE(28, 28, 5, 0x20, 0x10, 3, 1), - PIN_FIELD_BASE(29, 29, 5, 0x20, 0x10, 1, 1), - PIN_FIELD_BASE(30, 30, 5, 0x20, 0x10, 2, 1), - PIN_FIELD_BASE(31, 31, 5, 0x20, 0x10, 5, 1), - - PIN_FIELD_BASE(32, 32, 1, 0x10, 0x10, 2, 1), - PIN_FIELD_BASE(33, 33, 1, 0x10, 0x10, 3, 1), - - PIN_FIELD_BASE(34, 34, 4, 0x20, 0x10, 5, 1), - PIN_FIELD_BASE(35, 35, 4, 0x20, 0x10, 7, 1), - - PIN_FIELD_BASE(36, 36, 3, 0x10, 0x10, 2, 1), - PIN_FIELD_BASE(37, 37, 3, 0x10, 0x10, 3, 1), - PIN_FIELD_BASE(38, 38, 3, 0x10, 0x10, 0, 1), - PIN_FIELD_BASE(39, 39, 3, 0x10, 0x10, 1, 1), - - PIN_FIELD_BASE(40, 40, 7, 0x30, 0x10, 1, 1), - PIN_FIELD_BASE(41, 41, 7, 0x30, 0x10, 0, 1), - PIN_FIELD_BASE(42, 42, 7, 0x30, 0x10, 9, 1), - PIN_FIELD_BASE(43, 43, 7, 0x30, 0x10, 7, 1), - PIN_FIELD_BASE(44, 44, 7, 0x30, 0x10, 8, 1), - PIN_FIELD_BASE(45, 45, 7, 0x30, 0x10, 3, 1), - PIN_FIELD_BASE(46, 46, 7, 0x30, 0x10, 4, 1), - PIN_FIELD_BASE(47, 47, 7, 0x30, 0x10, 5, 1), - PIN_FIELD_BASE(48, 48, 7, 0x30, 0x10, 6, 1), - PIN_FIELD_BASE(49, 49, 7, 0x30, 0x10, 2, 1), - - PIN_FIELD_BASE(50, 50, 6, 0x10, 0x10, 0, 1), - PIN_FIELD_BASE(51, 51, 6, 0x10, 0x10, 2, 1), - PIN_FIELD_BASE(52, 52, 6, 0x10, 0x10, 3, 1), - PIN_FIELD_BASE(53, 53, 6, 0x10, 0x10, 4, 1), - PIN_FIELD_BASE(54, 54, 6, 0x10, 0x10, 5, 1), - PIN_FIELD_BASE(55, 55, 6, 0x10, 0x10, 6, 1), - PIN_FIELD_BASE(56, 56, 6, 0x10, 0x10, 1, 1), -}; - -static const struct mtk_pin_field_calc mt7981_pin_smt_range[] = { - PIN_FIELD_BASE(0, 0, 1, 0x60, 0x10, 1, 1), - PIN_FIELD_BASE(1, 1, 1, 0x60, 0x10, 0, 1), - PIN_FIELD_BASE(2, 2, 5, 0x90, 0x10, 6, 1), - PIN_FIELD_BASE(3, 3, 4, 0x80, 0x10, 6, 1), - PIN_FIELD_BASE(4, 4, 4, 0x80, 0x10, 2, 1), - PIN_FIELD_BASE(5, 5, 4, 0x80, 0x10, 1, 1), - PIN_FIELD_BASE(6, 6, 4, 0x80, 0x10, 3, 1), - PIN_FIELD_BASE(7, 7, 4, 0x80, 0x10, 0, 1), - PIN_FIELD_BASE(8, 8, 4, 0x80, 0x10, 4, 1), - - PIN_FIELD_BASE(9, 9, 5, 0x90, 0x10, 9, 1), - PIN_FIELD_BASE(10, 10, 5, 0x90, 0x10, 8, 1), - PIN_FIELD_BASE(11, 11, 5, 0x90, 0x10, 10, 1), - PIN_FIELD_BASE(12, 12, 5, 0x90, 0x10, 7, 1), - PIN_FIELD_BASE(13, 13, 5, 0x90, 0x10, 11, 1), - - PIN_FIELD_BASE(14, 14, 4, 0x80, 0x10, 8, 1), - - PIN_FIELD_BASE(15, 15, 2, 0x90, 0x10, 0, 1), - PIN_FIELD_BASE(16, 16, 2, 0x90, 0x10, 1, 1), - PIN_FIELD_BASE(17, 17, 2, 0x90, 0x10, 5, 1), - PIN_FIELD_BASE(18, 18, 2, 0x90, 0x10, 4, 1), - PIN_FIELD_BASE(19, 19, 2, 0x90, 0x10, 2, 1), - PIN_FIELD_BASE(20, 20, 2, 0x90, 0x10, 3, 1), - PIN_FIELD_BASE(21, 21, 2, 0x90, 0x10, 6, 1), - PIN_FIELD_BASE(22, 22, 2, 0x90, 0x10, 7, 1), - PIN_FIELD_BASE(23, 23, 2, 0x90, 0x10, 10, 1), - PIN_FIELD_BASE(24, 24, 2, 0x90, 0x10, 9, 1), - PIN_FIELD_BASE(25, 25, 2, 0x90, 0x10, 8, 1), - - PIN_FIELD_BASE(26, 26, 5, 0x90, 0x10, 0, 1), - PIN_FIELD_BASE(27, 27, 5, 0x90, 0x10, 4, 1), - PIN_FIELD_BASE(28, 28, 5, 0x90, 0x10, 3, 1), - PIN_FIELD_BASE(29, 29, 5, 0x90, 0x10, 1, 1), - PIN_FIELD_BASE(30, 30, 5, 0x90, 0x10, 2, 1), - PIN_FIELD_BASE(31, 31, 5, 0x90, 0x10, 5, 1), - - PIN_FIELD_BASE(32, 32, 1, 0x60, 0x10, 2, 1), - PIN_FIELD_BASE(33, 33, 1, 0x60, 0x10, 3, 1), - - PIN_FIELD_BASE(34, 34, 4, 0x80, 0x10, 5, 1), - PIN_FIELD_BASE(35, 35, 4, 0x80, 0x10, 7, 1), - - PIN_FIELD_BASE(36, 36, 3, 0x60, 0x10, 2, 1), - PIN_FIELD_BASE(37, 37, 3, 0x60, 0x10, 3, 1), - PIN_FIELD_BASE(38, 38, 3, 0x60, 0x10, 0, 1), - PIN_FIELD_BASE(39, 39, 3, 0x60, 0x10, 1, 1), - - PIN_FIELD_BASE(40, 40, 7, 0x70, 0x10, 1, 1), - PIN_FIELD_BASE(41, 41, 7, 0x70, 0x10, 0, 1), - PIN_FIELD_BASE(42, 42, 7, 0x70, 0x10, 9, 1), - PIN_FIELD_BASE(43, 43, 7, 0x70, 0x10, 7, 1), - PIN_FIELD_BASE(44, 44, 7, 0x30, 0x10, 8, 1), - PIN_FIELD_BASE(45, 45, 7, 0x70, 0x10, 3, 1), - PIN_FIELD_BASE(46, 46, 7, 0x70, 0x10, 4, 1), - PIN_FIELD_BASE(47, 47, 7, 0x70, 0x10, 5, 1), - PIN_FIELD_BASE(48, 48, 7, 0x70, 0x10, 6, 1), - PIN_FIELD_BASE(49, 49, 7, 0x70, 0x10, 2, 1), - - PIN_FIELD_BASE(50, 50, 6, 0x50, 0x10, 0, 1), - PIN_FIELD_BASE(51, 51, 6, 0x50, 0x10, 2, 1), - PIN_FIELD_BASE(52, 52, 6, 0x50, 0x10, 3, 1), - PIN_FIELD_BASE(53, 53, 6, 0x50, 0x10, 4, 1), - PIN_FIELD_BASE(54, 54, 6, 0x50, 0x10, 5, 1), - PIN_FIELD_BASE(55, 55, 6, 0x50, 0x10, 6, 1), - PIN_FIELD_BASE(56, 56, 6, 0x50, 0x10, 1, 1), -}; - -static const struct mtk_pin_field_calc mt7981_pin_pu_range[] = { - PIN_FIELD_BASE(40, 40, 7, 0x50, 0x10, 1, 1), - PIN_FIELD_BASE(41, 41, 7, 0x50, 0x10, 0, 1), - PIN_FIELD_BASE(42, 42, 7, 0x50, 0x10, 9, 1), - PIN_FIELD_BASE(43, 43, 7, 0x50, 0x10, 7, 1), - PIN_FIELD_BASE(44, 44, 7, 0x50, 0x10, 8, 1), - PIN_FIELD_BASE(45, 45, 7, 0x50, 0x10, 3, 1), - PIN_FIELD_BASE(46, 46, 7, 0x50, 0x10, 4, 1), - PIN_FIELD_BASE(47, 47, 7, 0x50, 0x10, 5, 1), - PIN_FIELD_BASE(48, 48, 7, 0x50, 0x10, 6, 1), - PIN_FIELD_BASE(49, 49, 7, 0x50, 0x10, 2, 1), - - PIN_FIELD_BASE(50, 50, 6, 0x30, 0x10, 0, 1), - PIN_FIELD_BASE(51, 51, 6, 0x30, 0x10, 2, 1), - PIN_FIELD_BASE(52, 52, 6, 0x30, 0x10, 3, 1), - PIN_FIELD_BASE(53, 53, 6, 0x30, 0x10, 4, 1), - PIN_FIELD_BASE(54, 54, 6, 0x30, 0x10, 5, 1), - PIN_FIELD_BASE(55, 55, 6, 0x30, 0x10, 6, 1), - PIN_FIELD_BASE(56, 56, 6, 0x30, 0x10, 1, 1), -}; - -static const struct mtk_pin_field_calc mt7981_pin_pd_range[] = { - PIN_FIELD_BASE(40, 40, 7, 0x40, 0x10, 1, 1), - PIN_FIELD_BASE(41, 41, 7, 0x40, 0x10, 0, 1), - PIN_FIELD_BASE(42, 42, 7, 0x40, 0x10, 9, 1), - PIN_FIELD_BASE(43, 43, 7, 0x40, 0x10, 7, 1), - PIN_FIELD_BASE(44, 44, 7, 0x40, 0x10, 8, 1), - PIN_FIELD_BASE(45, 45, 7, 0x40, 0x10, 3, 1), - PIN_FIELD_BASE(46, 46, 7, 0x40, 0x10, 4, 1), - PIN_FIELD_BASE(47, 47, 7, 0x40, 0x10, 5, 1), - PIN_FIELD_BASE(48, 48, 7, 0x40, 0x10, 6, 1), - PIN_FIELD_BASE(49, 49, 7, 0x40, 0x10, 2, 1), - - PIN_FIELD_BASE(50, 50, 6, 0x20, 0x10, 0, 1), - PIN_FIELD_BASE(51, 51, 6, 0x20, 0x10, 2, 1), - PIN_FIELD_BASE(52, 52, 6, 0x20, 0x10, 3, 1), - PIN_FIELD_BASE(53, 53, 6, 0x20, 0x10, 4, 1), - PIN_FIELD_BASE(54, 54, 6, 0x20, 0x10, 5, 1), - PIN_FIELD_BASE(55, 55, 6, 0x20, 0x10, 6, 1), - PIN_FIELD_BASE(56, 56, 6, 0x20, 0x10, 1, 1), -}; - -static const struct mtk_pin_field_calc mt7981_pin_drv_range[] = { - PIN_FIELD_BASE(0, 0, 1, 0x00, 0x10, 3, 3), - PIN_FIELD_BASE(1, 1, 1, 0x00, 0x10, 0, 3), - - PIN_FIELD_BASE(2, 2, 5, 0x00, 0x10, 18, 3), - - PIN_FIELD_BASE(3, 3, 4, 0x00, 0x10, 18, 1), - PIN_FIELD_BASE(4, 4, 4, 0x00, 0x10, 6, 1), - PIN_FIELD_BASE(5, 5, 4, 0x00, 0x10, 3, 3), - PIN_FIELD_BASE(6, 6, 4, 0x00, 0x10, 9, 3), - PIN_FIELD_BASE(7, 7, 4, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(8, 8, 4, 0x00, 0x10, 12, 3), - - PIN_FIELD_BASE(9, 9, 5, 0x00, 0x10, 27, 3), - PIN_FIELD_BASE(10, 10, 5, 0x00, 0x10, 24, 3), - PIN_FIELD_BASE(11, 11, 5, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(12, 12, 5, 0x00, 0x10, 21, 3), - PIN_FIELD_BASE(13, 13, 5, 0x00, 0x10, 3, 3), - - PIN_FIELD_BASE(14, 14, 4, 0x00, 0x10, 27, 3), - - PIN_FIELD_BASE(15, 15, 2, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(16, 16, 2, 0x00, 0x10, 3, 3), - PIN_FIELD_BASE(17, 17, 2, 0x00, 0x10, 15, 3), - PIN_FIELD_BASE(18, 18, 2, 0x00, 0x10, 12, 3), - PIN_FIELD_BASE(19, 19, 2, 0x00, 0x10, 6, 3), - PIN_FIELD_BASE(20, 20, 2, 0x00, 0x10, 9, 3), - PIN_FIELD_BASE(21, 21, 2, 0x00, 0x10, 18, 3), - PIN_FIELD_BASE(22, 22, 2, 0x00, 0x10, 21, 3), - PIN_FIELD_BASE(23, 23, 2, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(24, 24, 2, 0x00, 0x10, 27, 3), - PIN_FIELD_BASE(25, 25, 2, 0x00, 0x10, 24, 3), - - PIN_FIELD_BASE(26, 26, 5, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(27, 27, 5, 0x00, 0x10, 12, 3), - PIN_FIELD_BASE(28, 28, 5, 0x00, 0x10, 9, 3), - PIN_FIELD_BASE(29, 29, 5, 0x00, 0x10, 3, 3), - PIN_FIELD_BASE(30, 30, 5, 0x00, 0x10, 6, 3), - PIN_FIELD_BASE(31, 31, 5, 0x00, 0x10, 15, 3), - - PIN_FIELD_BASE(32, 32, 1, 0x00, 0x10, 9, 3), - PIN_FIELD_BASE(33, 33, 1, 0x00, 0x10, 12, 3), - - PIN_FIELD_BASE(34, 34, 4, 0x00, 0x10, 15, 3), - PIN_FIELD_BASE(35, 35, 4, 0x00, 0x10, 21, 3), - - PIN_FIELD_BASE(36, 36, 3, 0x00, 0x10, 6, 3), - PIN_FIELD_BASE(37, 37, 3, 0x00, 0x10, 9, 3), - PIN_FIELD_BASE(38, 38, 3, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(39, 39, 3, 0x00, 0x10, 3, 3), - - PIN_FIELD_BASE(40, 40, 7, 0x00, 0x10, 3, 3), - PIN_FIELD_BASE(41, 41, 7, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(42, 42, 7, 0x00, 0x10, 27, 3), - PIN_FIELD_BASE(43, 43, 7, 0x00, 0x10, 21, 3), - PIN_FIELD_BASE(44, 44, 7, 0x00, 0x10, 24, 3), - PIN_FIELD_BASE(45, 45, 7, 0x00, 0x10, 9, 3), - PIN_FIELD_BASE(46, 46, 7, 0x00, 0x10, 12, 3), - PIN_FIELD_BASE(47, 47, 7, 0x00, 0x10, 15, 3), - PIN_FIELD_BASE(48, 48, 7, 0x00, 0x10, 18, 3), - PIN_FIELD_BASE(49, 49, 7, 0x00, 0x10, 6, 3), - - PIN_FIELD_BASE(50, 50, 6, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(51, 51, 6, 0x00, 0x10, 6, 3), - PIN_FIELD_BASE(52, 52, 6, 0x00, 0x10, 9, 3), - PIN_FIELD_BASE(53, 53, 6, 0x00, 0x10, 12, 3), - PIN_FIELD_BASE(54, 54, 6, 0x00, 0x10, 15, 3), - PIN_FIELD_BASE(55, 55, 6, 0x00, 0x10, 18, 3), - PIN_FIELD_BASE(56, 56, 6, 0x00, 0x10, 3, 3), -}; - -static const struct mtk_pin_field_calc mt7981_pin_pupd_range[] = { - PIN_FIELD_BASE(0, 0, 1, 0x20, 0x10, 1, 1), - PIN_FIELD_BASE(1, 1, 1, 0x20, 0x10, 0, 1), - PIN_FIELD_BASE(2, 2, 5, 0x30, 0x10, 6, 1), - PIN_FIELD_BASE(3, 3, 4, 0x30, 0x10, 6, 1), - PIN_FIELD_BASE(4, 4, 4, 0x30, 0x10, 2, 1), - PIN_FIELD_BASE(5, 5, 4, 0x30, 0x10, 1, 1), - PIN_FIELD_BASE(6, 6, 4, 0x30, 0x10, 3, 1), - PIN_FIELD_BASE(7, 7, 4, 0x30, 0x10, 0, 1), - PIN_FIELD_BASE(8, 8, 4, 0x30, 0x10, 4, 1), - - PIN_FIELD_BASE(9, 9, 5, 0x30, 0x10, 9, 1), - PIN_FIELD_BASE(10, 10, 5, 0x30, 0x10, 8, 1), - PIN_FIELD_BASE(11, 11, 5, 0x30, 0x10, 10, 1), - PIN_FIELD_BASE(12, 12, 5, 0x30, 0x10, 7, 1), - PIN_FIELD_BASE(13, 13, 5, 0x30, 0x10, 11, 1), - - PIN_FIELD_BASE(14, 14, 4, 0x30, 0x10, 8, 1), - - PIN_FIELD_BASE(15, 15, 2, 0x30, 0x10, 0, 1), - PIN_FIELD_BASE(16, 16, 2, 0x30, 0x10, 1, 1), - PIN_FIELD_BASE(17, 17, 2, 0x30, 0x10, 5, 1), - PIN_FIELD_BASE(18, 18, 2, 0x30, 0x10, 4, 1), - PIN_FIELD_BASE(19, 19, 2, 0x30, 0x10, 2, 1), - PIN_FIELD_BASE(20, 20, 2, 0x90, 0x10, 3, 1), - PIN_FIELD_BASE(21, 21, 2, 0x30, 0x10, 6, 1), - PIN_FIELD_BASE(22, 22, 2, 0x30, 0x10, 7, 1), - PIN_FIELD_BASE(23, 23, 2, 0x30, 0x10, 10, 1), - PIN_FIELD_BASE(24, 24, 2, 0x30, 0x10, 9, 1), - PIN_FIELD_BASE(25, 25, 2, 0x30, 0x10, 8, 1), - - PIN_FIELD_BASE(26, 26, 5, 0x30, 0x10, 0, 1), - PIN_FIELD_BASE(27, 27, 5, 0x30, 0x10, 4, 1), - PIN_FIELD_BASE(28, 28, 5, 0x30, 0x10, 3, 1), - PIN_FIELD_BASE(29, 29, 5, 0x30, 0x10, 1, 1), - PIN_FIELD_BASE(30, 30, 5, 0x30, 0x10, 2, 1), - PIN_FIELD_BASE(31, 31, 5, 0x30, 0x10, 5, 1), - - PIN_FIELD_BASE(32, 32, 1, 0x20, 0x10, 2, 1), - PIN_FIELD_BASE(33, 33, 1, 0x20, 0x10, 3, 1), - - PIN_FIELD_BASE(34, 34, 4, 0x30, 0x10, 5, 1), - PIN_FIELD_BASE(35, 35, 4, 0x30, 0x10, 7, 1), - - PIN_FIELD_BASE(36, 36, 3, 0x20, 0x10, 2, 1), - PIN_FIELD_BASE(37, 37, 3, 0x20, 0x10, 3, 1), - PIN_FIELD_BASE(38, 38, 3, 0x20, 0x10, 0, 1), - PIN_FIELD_BASE(39, 39, 3, 0x20, 0x10, 1, 1), -}; - -static const struct mtk_pin_field_calc mt7981_pin_r0_range[] = { - PIN_FIELD_BASE(0, 0, 1, 0x30, 0x10, 1, 1), - PIN_FIELD_BASE(1, 1, 1, 0x30, 0x10, 0, 1), - PIN_FIELD_BASE(2, 2, 5, 0x40, 0x10, 6, 1), - PIN_FIELD_BASE(3, 3, 4, 0x40, 0x10, 6, 1), - PIN_FIELD_BASE(4, 4, 4, 0x40, 0x10, 2, 1), - PIN_FIELD_BASE(5, 5, 4, 0x40, 0x10, 1, 1), - PIN_FIELD_BASE(6, 6, 4, 0x40, 0x10, 3, 1), - PIN_FIELD_BASE(7, 7, 4, 0x40, 0x10, 0, 1), - PIN_FIELD_BASE(8, 8, 4, 0x40, 0x10, 4, 1), - - PIN_FIELD_BASE(9, 9, 5, 0x40, 0x10, 9, 1), - PIN_FIELD_BASE(10, 10, 5, 0x40, 0x10, 8, 1), - PIN_FIELD_BASE(11, 11, 5, 0x40, 0x10, 10, 1), - PIN_FIELD_BASE(12, 12, 5, 0x40, 0x10, 7, 1), - PIN_FIELD_BASE(13, 13, 5, 0x40, 0x10, 11, 1), - - PIN_FIELD_BASE(14, 14, 4, 0x40, 0x10, 8, 1), - - PIN_FIELD_BASE(15, 15, 2, 0x40, 0x10, 0, 1), - PIN_FIELD_BASE(16, 16, 2, 0x40, 0x10, 1, 1), - PIN_FIELD_BASE(17, 17, 2, 0x40, 0x10, 5, 1), - PIN_FIELD_BASE(18, 18, 2, 0x40, 0x10, 4, 1), - PIN_FIELD_BASE(19, 19, 2, 0x40, 0x10, 2, 1), - PIN_FIELD_BASE(20, 20, 2, 0x40, 0x10, 3, 1), - PIN_FIELD_BASE(21, 21, 2, 0x40, 0x10, 6, 1), - PIN_FIELD_BASE(22, 22, 2, 0x40, 0x10, 7, 1), - PIN_FIELD_BASE(23, 23, 2, 0x40, 0x10, 10, 1), - PIN_FIELD_BASE(24, 24, 2, 0x40, 0x10, 9, 1), - PIN_FIELD_BASE(25, 25, 2, 0x40, 0x10, 8, 1), - - PIN_FIELD_BASE(26, 26, 5, 0x40, 0x10, 0, 1), - PIN_FIELD_BASE(27, 27, 5, 0x40, 0x10, 4, 1), - PIN_FIELD_BASE(28, 28, 5, 0x40, 0x10, 3, 1), - PIN_FIELD_BASE(29, 29, 5, 0x40, 0x10, 1, 1), - PIN_FIELD_BASE(30, 30, 5, 0x40, 0x10, 2, 1), - PIN_FIELD_BASE(31, 31, 5, 0x40, 0x10, 5, 1), - - PIN_FIELD_BASE(32, 32, 1, 0x30, 0x10, 2, 1), - PIN_FIELD_BASE(33, 33, 1, 0x30, 0x10, 3, 1), - - PIN_FIELD_BASE(34, 34, 4, 0x40, 0x10, 5, 1), - PIN_FIELD_BASE(35, 35, 4, 0x40, 0x10, 7, 1), - - PIN_FIELD_BASE(36, 36, 3, 0x30, 0x10, 2, 1), - PIN_FIELD_BASE(37, 37, 3, 0x30, 0x10, 3, 1), - PIN_FIELD_BASE(38, 38, 3, 0x30, 0x10, 0, 1), - PIN_FIELD_BASE(39, 39, 3, 0x30, 0x10, 1, 1), -}; - -static const struct mtk_pin_field_calc mt7981_pin_r1_range[] = { - PIN_FIELD_BASE(0, 0, 1, 0x40, 0x10, 1, 1), - PIN_FIELD_BASE(1, 1, 1, 0x40, 0x10, 0, 1), - PIN_FIELD_BASE(2, 2, 5, 0x50, 0x10, 6, 1), - PIN_FIELD_BASE(3, 3, 4, 0x50, 0x10, 6, 1), - PIN_FIELD_BASE(4, 4, 4, 0x50, 0x10, 2, 1), - PIN_FIELD_BASE(5, 5, 4, 0x50, 0x10, 1, 1), - PIN_FIELD_BASE(6, 6, 4, 0x50, 0x10, 3, 1), - PIN_FIELD_BASE(7, 7, 4, 0x50, 0x10, 0, 1), - PIN_FIELD_BASE(8, 8, 4, 0x50, 0x10, 4, 1), - - PIN_FIELD_BASE(9, 9, 5, 0x50, 0x10, 9, 1), - PIN_FIELD_BASE(10, 10, 5, 0x50, 0x10, 8, 1), - PIN_FIELD_BASE(11, 11, 5, 0x50, 0x10, 10, 1), - PIN_FIELD_BASE(12, 12, 5, 0x50, 0x10, 7, 1), - PIN_FIELD_BASE(13, 13, 5, 0x50, 0x10, 11, 1), - - PIN_FIELD_BASE(14, 14, 4, 0x50, 0x10, 8, 1), - - PIN_FIELD_BASE(15, 15, 2, 0x50, 0x10, 0, 1), - PIN_FIELD_BASE(16, 16, 2, 0x50, 0x10, 1, 1), - PIN_FIELD_BASE(17, 17, 2, 0x50, 0x10, 5, 1), - PIN_FIELD_BASE(18, 18, 2, 0x50, 0x10, 4, 1), - PIN_FIELD_BASE(19, 19, 2, 0x50, 0x10, 2, 1), - PIN_FIELD_BASE(20, 20, 2, 0x50, 0x10, 3, 1), - PIN_FIELD_BASE(21, 21, 2, 0x50, 0x10, 6, 1), - PIN_FIELD_BASE(22, 22, 2, 0x50, 0x10, 7, 1), - PIN_FIELD_BASE(23, 23, 2, 0x50, 0x10, 10, 1), - PIN_FIELD_BASE(24, 24, 2, 0x50, 0x10, 9, 1), - PIN_FIELD_BASE(25, 25, 2, 0x50, 0x10, 8, 1), - - PIN_FIELD_BASE(26, 26, 5, 0x50, 0x10, 0, 1), - PIN_FIELD_BASE(27, 27, 5, 0x50, 0x10, 4, 1), - PIN_FIELD_BASE(28, 28, 5, 0x50, 0x10, 3, 1), - PIN_FIELD_BASE(29, 29, 5, 0x50, 0x10, 1, 1), - PIN_FIELD_BASE(30, 30, 5, 0x50, 0x10, 2, 1), - PIN_FIELD_BASE(31, 31, 5, 0x50, 0x10, 5, 1), - - PIN_FIELD_BASE(32, 32, 1, 0x40, 0x10, 2, 1), - PIN_FIELD_BASE(33, 33, 1, 0x40, 0x10, 3, 1), - - PIN_FIELD_BASE(34, 34, 4, 0x50, 0x10, 5, 1), - PIN_FIELD_BASE(35, 35, 4, 0x50, 0x10, 7, 1), - - PIN_FIELD_BASE(36, 36, 3, 0x40, 0x10, 2, 1), - PIN_FIELD_BASE(37, 37, 3, 0x40, 0x10, 3, 1), - PIN_FIELD_BASE(38, 38, 3, 0x40, 0x10, 0, 1), - PIN_FIELD_BASE(39, 39, 3, 0x40, 0x10, 1, 1), -}; - -static const unsigned int mt7981_pull_type[] = { - MTK_PULL_PUPD_R1R0_TYPE,/*0*/ MTK_PULL_PUPD_R1R0_TYPE,/*1*/ - MTK_PULL_PUPD_R1R0_TYPE,/*2*/ MTK_PULL_PUPD_R1R0_TYPE,/*3*/ - MTK_PULL_PUPD_R1R0_TYPE,/*4*/ MTK_PULL_PUPD_R1R0_TYPE,/*5*/ - MTK_PULL_PUPD_R1R0_TYPE,/*6*/ MTK_PULL_PUPD_R1R0_TYPE,/*7*/ - MTK_PULL_PUPD_R1R0_TYPE,/*8*/ MTK_PULL_PUPD_R1R0_TYPE,/*9*/ - MTK_PULL_PUPD_R1R0_TYPE,/*10*/ MTK_PULL_PUPD_R1R0_TYPE,/*11*/ - MTK_PULL_PUPD_R1R0_TYPE,/*12*/ MTK_PULL_PUPD_R1R0_TYPE,/*13*/ - MTK_PULL_PUPD_R1R0_TYPE,/*14*/ MTK_PULL_PUPD_R1R0_TYPE,/*15*/ - MTK_PULL_PUPD_R1R0_TYPE,/*16*/ MTK_PULL_PUPD_R1R0_TYPE,/*17*/ - MTK_PULL_PUPD_R1R0_TYPE,/*18*/ MTK_PULL_PUPD_R1R0_TYPE,/*19*/ - MTK_PULL_PUPD_R1R0_TYPE,/*20*/ MTK_PULL_PUPD_R1R0_TYPE,/*21*/ - MTK_PULL_PUPD_R1R0_TYPE,/*22*/ MTK_PULL_PUPD_R1R0_TYPE,/*23*/ - MTK_PULL_PUPD_R1R0_TYPE,/*24*/ MTK_PULL_PUPD_R1R0_TYPE,/*25*/ - MTK_PULL_PUPD_R1R0_TYPE,/*26*/ MTK_PULL_PUPD_R1R0_TYPE,/*27*/ - MTK_PULL_PUPD_R1R0_TYPE,/*28*/ MTK_PULL_PUPD_R1R0_TYPE,/*29*/ - MTK_PULL_PUPD_R1R0_TYPE,/*30*/ MTK_PULL_PUPD_R1R0_TYPE,/*31*/ - MTK_PULL_PUPD_R1R0_TYPE,/*32*/ MTK_PULL_PUPD_R1R0_TYPE,/*33*/ - MTK_PULL_PUPD_R1R0_TYPE,/*34*/ MTK_PULL_PUPD_R1R0_TYPE,/*35*/ - MTK_PULL_PUPD_R1R0_TYPE,/*36*/ MTK_PULL_PUPD_R1R0_TYPE,/*37*/ - MTK_PULL_PUPD_R1R0_TYPE,/*38*/ MTK_PULL_PUPD_R1R0_TYPE,/*39*/ - MTK_PULL_PU_PD_TYPE,/*40*/ MTK_PULL_PU_PD_TYPE,/*41*/ - MTK_PULL_PU_PD_TYPE,/*42*/ MTK_PULL_PU_PD_TYPE,/*43*/ - MTK_PULL_PU_PD_TYPE,/*44*/ MTK_PULL_PU_PD_TYPE,/*45*/ - MTK_PULL_PU_PD_TYPE,/*46*/ MTK_PULL_PU_PD_TYPE,/*47*/ - MTK_PULL_PU_PD_TYPE,/*48*/ MTK_PULL_PU_PD_TYPE,/*49*/ - MTK_PULL_PU_PD_TYPE,/*50*/ MTK_PULL_PU_PD_TYPE,/*51*/ - MTK_PULL_PU_PD_TYPE,/*52*/ MTK_PULL_PU_PD_TYPE,/*53*/ - MTK_PULL_PU_PD_TYPE,/*54*/ MTK_PULL_PU_PD_TYPE,/*55*/ - MTK_PULL_PU_PD_TYPE,/*56*/ -}; - -static const struct mtk_pin_reg_calc mt7981_reg_cals[] = { - [PINCTRL_PIN_REG_MODE] = MTK_RANGE(mt7981_pin_mode_range), - [PINCTRL_PIN_REG_DIR] = MTK_RANGE(mt7981_pin_dir_range), - [PINCTRL_PIN_REG_DI] = MTK_RANGE(mt7981_pin_di_range), - [PINCTRL_PIN_REG_DO] = MTK_RANGE(mt7981_pin_do_range), - [PINCTRL_PIN_REG_SMT] = MTK_RANGE(mt7981_pin_smt_range), - [PINCTRL_PIN_REG_IES] = MTK_RANGE(mt7981_pin_ies_range), - [PINCTRL_PIN_REG_PU] = MTK_RANGE(mt7981_pin_pu_range), - [PINCTRL_PIN_REG_PD] = MTK_RANGE(mt7981_pin_pd_range), - [PINCTRL_PIN_REG_DRV] = MTK_RANGE(mt7981_pin_drv_range), - [PINCTRL_PIN_REG_PUPD] = MTK_RANGE(mt7981_pin_pupd_range), - [PINCTRL_PIN_REG_R0] = MTK_RANGE(mt7981_pin_r0_range), - [PINCTRL_PIN_REG_R1] = MTK_RANGE(mt7981_pin_r1_range), -}; - -static const struct mtk_pin_desc mt7981_pins[] = { - MT7981_PIN(0, "GPIO_WPS"), - MT7981_PIN(1, "GPIO_RESET"), - MT7981_PIN(2, "SYS_WATCHDOG"), - MT7981_PIN(3, "PCIE_PERESET_N"), - MT7981_PIN(4, "JTAG_JTDO"), - MT7981_PIN(5, "JTAG_JTDI"), - MT7981_PIN(6, "JTAG_JTMS"), - MT7981_PIN(7, "JTAG_JTCLK"), - MT7981_PIN(8, "JTAG_JTRST_N"), - MT7981_PIN(9, "WO_JTAG_JTDO"), - MT7981_PIN(10, "WO_JTAG_JTDI"), - MT7981_PIN(11, "WO_JTAG_JTMS"), - MT7981_PIN(12, "WO_JTAG_JTCLK"), - MT7981_PIN(13, "WO_JTAG_JTRST_N"), - MT7981_PIN(14, "USB_VBUS"), - MT7981_PIN(15, "PWM0"), - MT7981_PIN(16, "SPI0_CLK"), - MT7981_PIN(17, "SPI0_MOSI"), - MT7981_PIN(18, "SPI0_MISO"), - MT7981_PIN(19, "SPI0_CS"), - MT7981_PIN(20, "SPI0_HOLD"), - MT7981_PIN(21, "SPI0_WP"), - MT7981_PIN(22, "SPI1_CLK"), - MT7981_PIN(23, "SPI1_MOSI"), - MT7981_PIN(24, "SPI1_MISO"), - MT7981_PIN(25, "SPI1_CS"), - MT7981_PIN(26, "SPI2_CLK"), - MT7981_PIN(27, "SPI2_MOSI"), - MT7981_PIN(28, "SPI2_MISO"), - MT7981_PIN(29, "SPI2_CS"), - MT7981_PIN(30, "SPI2_HOLD"), - MT7981_PIN(31, "SPI2_WP"), - MT7981_PIN(32, "UART0_RXD"), - MT7981_PIN(33, "UART0_TXD"), - MT7981_PIN(34, "PCIE_CLK_REQ"), - MT7981_PIN(35, "PCIE_WAKE_N"), - MT7981_PIN(36, "SMI_MDC"), - MT7981_PIN(37, "SMI_MDIO"), - MT7981_PIN(38, "GBE_INT"), - MT7981_PIN(39, "GBE_RESET"), - MT7981_PIN(40, "WF_DIG_RESETB"), - MT7981_PIN(41, "WF_CBA_RESETB"), - MT7981_PIN(42, "WF_XO_REQ"), - MT7981_PIN(43, "WF_TOP_CLK"), - MT7981_PIN(44, "WF_TOP_DATA"), - MT7981_PIN(45, "WF_HB1"), - MT7981_PIN(46, "WF_HB2"), - MT7981_PIN(47, "WF_HB3"), - MT7981_PIN(48, "WF_HB4"), - MT7981_PIN(49, "WF_HB0"), - MT7981_PIN(50, "WF_HB0_B"), - MT7981_PIN(51, "WF_HB5"), - MT7981_PIN(52, "WF_HB6"), - MT7981_PIN(53, "WF_HB7"), - MT7981_PIN(54, "WF_HB8"), - MT7981_PIN(55, "WF_HB9"), - MT7981_PIN(56, "WF_HB10"), -}; - -/* List all groups consisting of these pins dedicated to the enablement of - * certain hardware block and the corresponding mode for all of the pins. - * The hardware probably has multiple combinations of these pinouts. - */ - -/* WA_AICE */ -static int mt7981_wa_aice1_pins[] = { 0, 1, }; -static int mt7981_wa_aice1_funcs[] = { 2, 2, }; - -static int mt7981_wa_aice2_pins[] = { 0, 1, }; -static int mt7981_wa_aice2_funcs[] = { 3, 3, }; - -static int mt7981_wa_aice3_pins[] = { 28, 29, }; -static int mt7981_wa_aice3_funcs[] = { 3, 3, }; - -static int mt7981_wm_aice1_pins[] = { 9, 10, }; -static int mt7981_wm_aice1_funcs[] = { 2, 2, }; - -static int mt7981_wm_aice2_pins[] = { 30, 31, }; -static int mt7981_wm_aice2_funcs[] = { 5, 5, }; - -/* WM_UART */ -static int mt7981_wm_uart_0_pins[] = { 0, 1, }; -static int mt7981_wm_uart_0_funcs[] = { 5, 5, }; - -static int mt7981_wm_uart_1_pins[] = { 20, 21, }; -static int mt7981_wm_uart_1_funcs[] = { 4, 4, }; - -static int mt7981_wm_uart_2_pins[] = { 30, 31, }; -static int mt7981_wm_uart_2_funcs[] = { 3, 3, }; - -/* DFD */ -static int mt7981_dfd_pins[] = { 0, 1, 4, 5, }; -static int mt7981_dfd_funcs[] = { 5, 5, 6, 6, }; - -/* SYS_WATCHDOG */ -static int mt7981_watchdog_pins[] = { 2, }; -static int mt7981_watchdog_funcs[] = { 1, }; - -static int mt7981_watchdog1_pins[] = { 13, }; -static int mt7981_watchdog1_funcs[] = { 5, }; - -/* PCIE_PERESET_N */ -static int mt7981_pcie_pereset_pins[] = { 3, }; -static int mt7981_pcie_pereset_funcs[] = { 1, }; - -/* JTAG */ -static int mt7981_jtag_pins[] = { 4, 5, 6, 7, 8, }; -static int mt7981_jtag_funcs[] = { 1, 1, 1, 1, 1, }; - -/* WM_JTAG */ -static int mt7981_wm_jtag_0_pins[] = { 4, 5, 6, 7, 8, }; -static int mt7981_wm_jtag_0_funcs[] = { 2, 2, 2, 2, 2, }; - -static int mt7981_wm_jtag_1_pins[] = { 20, 21, 22, 23, 24, }; -static int mt7981_wm_jtag_1_funcs[] = { 5, 5, 5, 5, 5, }; - -/* WO0_JTAG */ -static int mt7981_wo0_jtag_0_pins[] = { 9, 10, 11, 12, 13, }; -static int mt7981_wo0_jtag_0_funcs[] = { 1, 1, 1, 1, 1, }; - -static int mt7981_wo0_jtag_1_pins[] = { 25, 26, 27, 28, 29, }; -static int mt7981_wo0_jtag_1_funcs[] = { 5, 5, 5, 5, 5, }; - -/* UART2 */ -static int mt7981_uart2_0_pins[] = { 4, 5, 6, 7, }; -static int mt7981_uart2_0_funcs[] = { 3, 3, 3, 3, }; - -static int mt7981_uart2_0_tx_rx_pins[] = { 4, 5, }; -static int mt7981_uart2_0_tx_rx_funcs[] = { 3, 3, }; - -/* GBE_LED0 */ -static int mt7981_gbe_led0_pins[] = { 8, }; -static int mt7981_gbe_led0_funcs[] = { 3, }; - -/* PTA_EXT */ -static int mt7981_pta_ext_0_pins[] = { 4, 5, 6, }; -static int mt7981_pta_ext_0_funcs[] = { 4, 4, 4, }; - -static int mt7981_pta_ext_1_pins[] = { 22, 23, 24, }; -static int mt7981_pta_ext_1_funcs[] = { 4, 4, 4, }; - -/* PWM2 */ -static int mt7981_pwm2_pins[] = { 7, }; -static int mt7981_pwm2_funcs[] = { 4, }; - -/* NET_WO0_UART_TXD */ -static int mt7981_net_wo0_uart_txd_0_pins[] = { 8, }; -static int mt7981_net_wo0_uart_txd_0_funcs[] = { 4, }; - -static int mt7981_net_wo0_uart_txd_1_pins[] = { 14, }; -static int mt7981_net_wo0_uart_txd_1_funcs[] = { 3, }; - -static int mt7981_net_wo0_uart_txd_2_pins[] = { 15, }; -static int mt7981_net_wo0_uart_txd_2_funcs[] = { 4, }; - -/* SPI1 */ -static int mt7981_spi1_0_pins[] = { 4, 5, 6, 7, }; -static int mt7981_spi1_0_funcs[] = { 5, 5, 5, 5, }; - -/* I2C */ -static int mt7981_i2c0_0_pins[] = { 6, 7, }; -static int mt7981_i2c0_0_funcs[] = { 6, 6, }; - -static int mt7981_i2c0_1_pins[] = { 30, 31, }; -static int mt7981_i2c0_1_funcs[] = { 4, 4, }; - -static int mt7981_i2c0_2_pins[] = { 36, 37, }; -static int mt7981_i2c0_2_funcs[] = { 2, 2, }; - -static int mt7981_u2_phy_i2c_pins[] = { 30, 31, }; -static int mt7981_u2_phy_i2c_funcs[] = { 6, 6, }; - -static int mt7981_u3_phy_i2c_pins[] = { 32, 33, }; -static int mt7981_u3_phy_i2c_funcs[] = { 3, 3, }; - -static int mt7981_sgmii1_phy_i2c_pins[] = { 32, 33, }; -static int mt7981_sgmii1_phy_i2c_funcs[] = { 2, 2, }; - -static int mt7981_sgmii0_phy_i2c_pins[] = { 32, 33, }; -static int mt7981_sgmii0_phy_i2c_funcs[] = { 5, 5, }; - -/* DFD_NTRST */ -static int mt7981_dfd_ntrst_pins[] = { 8, }; -static int mt7981_dfd_ntrst_funcs[] = { 6, }; - -/* PWM0 */ -static int mt7981_pwm0_0_pins[] = { 13, }; -static int mt7981_pwm0_0_funcs[] = { 2, }; - -static int mt7981_pwm0_1_pins[] = { 15, }; -static int mt7981_pwm0_1_funcs[] = { 1, }; - -/* PWM1 */ -static int mt7981_pwm1_0_pins[] = { 14, }; -static int mt7981_pwm1_0_funcs[] = { 2, }; - -static int mt7981_pwm1_1_pins[] = { 15, }; -static int mt7981_pwm1_1_funcs[] = { 3, }; - -/* GBE_LED1 */ -static int mt7981_gbe_led1_pins[] = { 13, }; -static int mt7981_gbe_led1_funcs[] = { 3, }; - -/* PCM */ -static int mt7981_pcm_pins[] = { 9, 10, 11, 12, 13, 25 }; -static int mt7981_pcm_funcs[] = { 4, 4, 4, 4, 4, 4, }; - -/* UDI */ -static int mt7981_udi_pins[] = { 9, 10, 11, 12, 13, }; -static int mt7981_udi_funcs[] = { 6, 6, 6, 6, 6, }; - -/* DRV_VBUS */ -static int mt7981_drv_vbus_pins[] = { 14, }; -static int mt7981_drv_vbus_funcs[] = { 1, }; - -/* EMMC */ -static int mt7981_emmc_45_pins[] = { 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, }; -static int mt7981_emmc_45_funcs[] = { 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, }; - -/* SNFI */ -static int mt7981_snfi_pins[] = { 16, 17, 18, 19, 20, 21, }; -static int mt7981_snfi_funcs[] = { 3, 3, 3, 3, 3, 3, }; - -/* SPI0 */ -static int mt7981_spi0_pins[] = { 16, 17, 18, 19, }; -static int mt7981_spi0_funcs[] = { 1, 1, 1, 1, }; - -/* SPI0 */ -static int mt7981_spi0_wp_hold_pins[] = { 20, 21, }; -static int mt7981_spi0_wp_hold_funcs[] = { 1, 1, }; - -/* SPI1 */ -static int mt7981_spi1_1_pins[] = { 22, 23, 24, 25, }; -static int mt7981_spi1_1_funcs[] = { 1, 1, 1, 1, }; - -/* SPI2 */ -static int mt7981_spi2_pins[] = { 26, 27, 28, 29, }; -static int mt7981_spi2_funcs[] = { 1, 1, 1, 1, }; - -/* SPI2 */ -static int mt7981_spi2_wp_hold_pins[] = { 30, 31, }; -static int mt7981_spi2_wp_hold_funcs[] = { 1, 1, }; - -/* UART1 */ -static int mt7981_uart1_0_pins[] = { 16, 17, 18, 19, }; -static int mt7981_uart1_0_funcs[] = { 4, 4, 4, 4, }; - -static int mt7981_uart1_1_pins[] = { 26, 27, 28, 29, }; -static int mt7981_uart1_1_funcs[] = { 2, 2, 2, 2, }; - -static int mt7981_uart1_2_pins[] = { 9, 10, }; -static int mt7981_uart1_2_funcs[] = { 2, 2, }; - -/* UART2 */ -static int mt7981_uart2_1_pins[] = { 22, 23, 24, 25, }; -static int mt7981_uart2_1_funcs[] = { 3, 3, 3, 3, }; - -/* UART0 */ -static int mt7981_uart0_pins[] = { 32, 33, }; -static int mt7981_uart0_funcs[] = { 1, 1, }; - -/* PCIE_CLK_REQ */ -static int mt7981_pcie_clk_pins[] = { 34, }; -static int mt7981_pcie_clk_funcs[] = { 2, }; - -/* PCIE_WAKE_N */ -static int mt7981_pcie_wake_pins[] = { 35, }; -static int mt7981_pcie_wake_funcs[] = { 2, }; - -/* MDC_MDIO */ -static int mt7981_smi_mdc_mdio_pins[] = { 36, 37, }; -static int mt7981_smi_mdc_mdio_funcs[] = { 1, 1, }; - -static int mt7981_gbe_ext_mdc_mdio_pins[] = { 36, 37, }; -static int mt7981_gbe_ext_mdc_mdio_funcs[] = { 3, 3, }; - -/* WF0_MODE1 */ -static int mt7981_wf0_mode1_pins[] = { 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56 }; -static int mt7981_wf0_mode1_funcs[] = { 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1 }; - -/* WF0_MODE3 */ -static int mt7981_wf0_mode3_pins[] = { 45, 46, 47, 48, 49, 51 }; -static int mt7981_wf0_mode3_funcs[] = { 2, 2, 2, 2, 2, 2 }; - -/* WF2G_LED */ -static int mt7981_wf2g_led0_pins[] = { 30, }; -static int mt7981_wf2g_led0_funcs[] = { 2, }; - -static int mt7981_wf2g_led1_pins[] = { 34, }; -static int mt7981_wf2g_led1_funcs[] = { 1, }; - -/* WF5G_LED */ -static int mt7981_wf5g_led0_pins[] = { 31, }; -static int mt7981_wf5g_led0_funcs[] = { 2, }; - -static int mt7981_wf5g_led1_pins[] = { 35, }; -static int mt7981_wf5g_led1_funcs[] = { 1, }; - -/* MT7531_INT */ -static int mt7981_mt7531_int_pins[] = { 38, }; -static int mt7981_mt7531_int_funcs[] = { 1, }; - -/* ANT_SEL */ -static int mt7981_ant_sel_pins[] = { 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 34, 35 }; -static int mt7981_ant_sel_funcs[] = { 6, 6, 6, 6, 6, 6, 6, 6, 6, 6, 6, 6 }; - -static const struct group_desc mt7981_groups[] = { - /* @GPIO(0,1): WA_AICE(2) */ - PINCTRL_PIN_GROUP("wa_aice1", mt7981_wa_aice1), - /* @GPIO(0,1): WA_AICE(3) */ - PINCTRL_PIN_GROUP("wa_aice2", mt7981_wa_aice2), - /* @GPIO(0,1): WM_UART(5) */ - PINCTRL_PIN_GROUP("wm_uart_0", mt7981_wm_uart_0), - /* @GPIO(0,1,4,5): DFD(6) */ - PINCTRL_PIN_GROUP("dfd", mt7981_dfd), - /* @GPIO(2): SYS_WATCHDOG(1) */ - PINCTRL_PIN_GROUP("watchdog", mt7981_watchdog), - /* @GPIO(3): PCIE_PERESET_N(1) */ - PINCTRL_PIN_GROUP("pcie_pereset", mt7981_pcie_pereset), - /* @GPIO(4,8) JTAG(1) */ - PINCTRL_PIN_GROUP("jtag", mt7981_jtag), - /* @GPIO(4,8) WM_JTAG(2) */ - PINCTRL_PIN_GROUP("wm_jtag_0", mt7981_wm_jtag_0), - /* @GPIO(9,13) WO0_JTAG(1) */ - PINCTRL_PIN_GROUP("wo0_jtag_0", mt7981_wo0_jtag_0), - /* @GPIO(4,7) WM_JTAG(3) */ - PINCTRL_PIN_GROUP("uart2_0", mt7981_uart2_0), - /* @GPIO(4,5) WM_JTAG(4) */ - PINCTRL_PIN_GROUP("uart2_0_tx_rx", mt7981_uart2_0_tx_rx), - /* @GPIO(8) GBE_LED0(3) */ - PINCTRL_PIN_GROUP("gbe_led0", mt7981_gbe_led0), - /* @GPIO(4,6) PTA_EXT(4) */ - PINCTRL_PIN_GROUP("pta_ext_0", mt7981_pta_ext_0), - /* @GPIO(7) PWM2(4) */ - PINCTRL_PIN_GROUP("pwm2", mt7981_pwm2), - /* @GPIO(8) NET_WO0_UART_TXD(4) */ - PINCTRL_PIN_GROUP("net_wo0_uart_txd_0", mt7981_net_wo0_uart_txd_0), - /* @GPIO(4,7) SPI1(5) */ - PINCTRL_PIN_GROUP("spi1_0", mt7981_spi1_0), - /* @GPIO(6,7) I2C(5) */ - PINCTRL_PIN_GROUP("i2c0_0", mt7981_i2c0_0), - /* @GPIO(0,1,4,5): DFD_NTRST(6) */ - PINCTRL_PIN_GROUP("dfd_ntrst", mt7981_dfd_ntrst), - /* @GPIO(9,10): WM_AICE(2) */ - PINCTRL_PIN_GROUP("wm_aice1", mt7981_wm_aice1), - /* @GPIO(13): PWM0(2) */ - PINCTRL_PIN_GROUP("pwm0_0", mt7981_pwm0_0), - /* @GPIO(15): PWM0(1) */ - PINCTRL_PIN_GROUP("pwm0_1", mt7981_pwm0_1), - /* @GPIO(14): PWM1(2) */ - PINCTRL_PIN_GROUP("pwm1_0", mt7981_pwm1_0), - /* @GPIO(15): PWM1(3) */ - PINCTRL_PIN_GROUP("pwm1_1", mt7981_pwm1_1), - /* @GPIO(14) NET_WO0_UART_TXD(3) */ - PINCTRL_PIN_GROUP("net_wo0_uart_txd_1", mt7981_net_wo0_uart_txd_1), - /* @GPIO(15) NET_WO0_UART_TXD(4) */ - PINCTRL_PIN_GROUP("net_wo0_uart_txd_2", mt7981_net_wo0_uart_txd_2), - /* @GPIO(13) GBE_LED0(3) */ - PINCTRL_PIN_GROUP("gbe_led1", mt7981_gbe_led1), - /* @GPIO(9,13) PCM(4) */ - PINCTRL_PIN_GROUP("pcm", mt7981_pcm), - /* @GPIO(13): SYS_WATCHDOG1(5) */ - PINCTRL_PIN_GROUP("watchdog1", mt7981_watchdog1), - /* @GPIO(9,13) UDI(4) */ - PINCTRL_PIN_GROUP("udi", mt7981_udi), - /* @GPIO(14) DRV_VBUS(1) */ - PINCTRL_PIN_GROUP("drv_vbus", mt7981_drv_vbus), - /* @GPIO(15,25): EMMC(2) */ - PINCTRL_PIN_GROUP("emmc_45", mt7981_emmc_45), - /* @GPIO(16,21): SNFI(3) */ - PINCTRL_PIN_GROUP("snfi", mt7981_snfi), - /* @GPIO(16,19): SPI0(1) */ - PINCTRL_PIN_GROUP("spi0", mt7981_spi0), - /* @GPIO(20,21): SPI0(1) */ - PINCTRL_PIN_GROUP("spi0_wp_hold", mt7981_spi0_wp_hold), - /* @GPIO(22,25) SPI1(1) */ - PINCTRL_PIN_GROUP("spi1_1", mt7981_spi1_1), - /* @GPIO(26,29): SPI2(1) */ - PINCTRL_PIN_GROUP("spi2", mt7981_spi2), - /* @GPIO(30,31): SPI0(1) */ - PINCTRL_PIN_GROUP("spi2_wp_hold", mt7981_spi2_wp_hold), - /* @GPIO(16,19): UART1(4) */ - PINCTRL_PIN_GROUP("uart1_0", mt7981_uart1_0), - /* @GPIO(26,29): UART1(2) */ - PINCTRL_PIN_GROUP("uart1_1", mt7981_uart1_1), - /* @GPIO(9,10): UART1(2) */ - PINCTRL_PIN_GROUP("uart1_2", mt7981_uart1_2), - /* @GPIO(22,25): UART1(3) */ - PINCTRL_PIN_GROUP("uart2_1", mt7981_uart2_1), - /* @GPIO(22,24) PTA_EXT(4) */ - PINCTRL_PIN_GROUP("pta_ext_1", mt7981_pta_ext_1), - /* @GPIO(20,21): WM_UART(4) */ - PINCTRL_PIN_GROUP("wm_aurt_1", mt7981_wm_uart_1), - /* @GPIO(30,31): WM_UART(3) */ - PINCTRL_PIN_GROUP("wm_aurt_2", mt7981_wm_uart_2), - /* @GPIO(20,24) WM_JTAG(5) */ - PINCTRL_PIN_GROUP("wm_jtag_1", mt7981_wm_jtag_1), - /* @GPIO(25,29) WO0_JTAG(5) */ - PINCTRL_PIN_GROUP("wo0_jtag_1", mt7981_wo0_jtag_1), - /* @GPIO(28,29): WA_AICE(3) */ - PINCTRL_PIN_GROUP("wa_aice3", mt7981_wa_aice3), - /* @GPIO(30,31): WM_AICE(5) */ - PINCTRL_PIN_GROUP("wm_aice2", mt7981_wm_aice2), - /* @GPIO(30,31): I2C(4) */ - PINCTRL_PIN_GROUP("i2c0_1", mt7981_i2c0_1), - /* @GPIO(30,31): I2C(6) */ - PINCTRL_PIN_GROUP("u2_phy_i2c", mt7981_u2_phy_i2c), - /* @GPIO(32,33): I2C(1) */ - PINCTRL_PIN_GROUP("uart0", mt7981_uart0), - /* @GPIO(32,33): I2C(2) */ - PINCTRL_PIN_GROUP("sgmii1_phy_i2c", mt7981_sgmii1_phy_i2c), - /* @GPIO(32,33): I2C(3) */ - PINCTRL_PIN_GROUP("u3_phy_i2c", mt7981_u3_phy_i2c), - /* @GPIO(32,33): I2C(5) */ - PINCTRL_PIN_GROUP("sgmii0_phy_i2c", mt7981_sgmii0_phy_i2c), - /* @GPIO(34): PCIE_CLK_REQ(2) */ - PINCTRL_PIN_GROUP("pcie_clk", mt7981_pcie_clk), - /* @GPIO(35): PCIE_WAKE_N(2) */ - PINCTRL_PIN_GROUP("pcie_wake", mt7981_pcie_wake), - /* @GPIO(36,37): I2C(2) */ - PINCTRL_PIN_GROUP("i2c0_2", mt7981_i2c0_2), - /* @GPIO(36,37): MDC_MDIO(1) */ - PINCTRL_PIN_GROUP("smi_mdc_mdio", mt7981_smi_mdc_mdio), - /* @GPIO(36,37): MDC_MDIO(3) */ - PINCTRL_PIN_GROUP("gbe_ext_mdc_mdio", mt7981_gbe_ext_mdc_mdio), - /* @GPIO(69,85): WF0_MODE1(1) */ - PINCTRL_PIN_GROUP("wf0_mode1", mt7981_wf0_mode1), - /* @GPIO(74,80): WF0_MODE3(3) */ - PINCTRL_PIN_GROUP("wf0_mode3", mt7981_wf0_mode3), - /* @GPIO(30): WF2G_LED(2) */ - PINCTRL_PIN_GROUP("wf2g_led0", mt7981_wf2g_led0), - /* @GPIO(34): WF2G_LED(1) */ - PINCTRL_PIN_GROUP("wf2g_led1", mt7981_wf2g_led1), - /* @GPIO(31): WF5G_LED(2) */ - PINCTRL_PIN_GROUP("wf5g_led0", mt7981_wf5g_led0), - /* @GPIO(35): WF5G_LED(1) */ - PINCTRL_PIN_GROUP("wf5g_led1", mt7981_wf5g_led1), - /* @GPIO(38): MT7531_INT(1) */ - PINCTRL_PIN_GROUP("mt7531_int", mt7981_mt7531_int), - /* @GPIO(14,15,26,17,18,19,20,21,22,23,24,25,34,35): ANT_SEL(1) */ - PINCTRL_PIN_GROUP("ant_sel", mt7981_ant_sel), -}; - -/* Joint those groups owning the same capability in user point of view which - * allows that people tend to use through the device tree. - */ -static const char *mt7981_wa_aice_groups[] = { "wa_aice1", "wa_aice2", "wm_aice1_1", - "wa_aice3", "wm_aice1_2", }; -static const char *mt7981_uart_groups[] = { "wm_uart_0", "uart2_0", - "uart1_2", "uart2_0_tx_rx", - "net_wo0_uart_txd_0", "net_wo0_uart_txd_1", "net_wo0_uart_txd_2", - "uart1_0", "uart1_1", "uart2_1", "wm_aurt_1", "wm_aurt_2", "uart0", }; -static const char *mt7981_dfd_groups[] = { "dfd", "dfd_ntrst", }; -static const char *mt7981_wdt_groups[] = { "watchdog", "watchdog1", }; -static const char *mt7981_pcie_groups[] = { "pcie_pereset", "pcie_clk", "pcie_wake", }; -static const char *mt7981_jtag_groups[] = { "jtag", "wm_jtag_0", "wo0_jtag_0", - "wo0_jtag_1", "wm_jtag_1", }; -static const char *mt7981_led_groups[] = { "gbe_led0", "gbe_led1", "wf2g_led0", - "wf2g_led1", "wf5g_led0", "wf5g_led1", }; -static const char *mt7981_pta_groups[] = { "pta_ext_0", "pta_ext_1", }; -static const char *mt7981_pwm_groups[] = { "pwm2", "pwm0_0", "pwm0_1", - "pwm1_0", "pwm1_1", }; -static const char *mt7981_spi_groups[] = { "spi1_0", "spi0", "spi0_wp_hold", "spi1_1", "spi2", - "spi2_wp_hold", }; -static const char *mt7981_i2c_groups[] = { "i2c0_0", "i2c0_1", "u2_phy_i2c", - "sgmii1_phy_i2c", "u3_phy_i2c", "sgmii0_phy_i2c", "i2c0_2", }; -static const char *mt7981_pcm_groups[] = { "pcm", }; -static const char *mt7981_udi_groups[] = { "udi", }; -static const char *mt7981_usb_groups[] = { "drv_vbus", }; -static const char *mt7981_flash_groups[] = { "emmc_45", "snfi", }; -static const char *mt7981_ethernet_groups[] = { "smi_mdc_mdio", "gbe_ext_mdc_mdio", - "wf0_mode1", "wf0_mode3", "mt7531_int", }; -static const char *mt7981_ant_groups[] = { "ant_sel", }; - -static const struct function_desc mt7981_functions[] = { - {"wa_aice", mt7981_wa_aice_groups, ARRAY_SIZE(mt7981_wa_aice_groups)}, - {"dfd", mt7981_dfd_groups, ARRAY_SIZE(mt7981_dfd_groups)}, - {"jtag", mt7981_jtag_groups, ARRAY_SIZE(mt7981_jtag_groups)}, - {"pta", mt7981_pta_groups, ARRAY_SIZE(mt7981_pta_groups)}, - {"pcm", mt7981_pcm_groups, ARRAY_SIZE(mt7981_pcm_groups)}, - {"udi", mt7981_udi_groups, ARRAY_SIZE(mt7981_udi_groups)}, - {"usb", mt7981_usb_groups, ARRAY_SIZE(mt7981_usb_groups)}, - {"ant", mt7981_ant_groups, ARRAY_SIZE(mt7981_ant_groups)}, - {"eth", mt7981_ethernet_groups, ARRAY_SIZE(mt7981_ethernet_groups)}, - {"i2c", mt7981_i2c_groups, ARRAY_SIZE(mt7981_i2c_groups)}, - {"led", mt7981_led_groups, ARRAY_SIZE(mt7981_led_groups)}, - {"pwm", mt7981_pwm_groups, ARRAY_SIZE(mt7981_pwm_groups)}, - {"spi", mt7981_spi_groups, ARRAY_SIZE(mt7981_spi_groups)}, - {"uart", mt7981_uart_groups, ARRAY_SIZE(mt7981_uart_groups)}, - {"watchdog", mt7981_wdt_groups, ARRAY_SIZE(mt7981_wdt_groups)}, - {"flash", mt7981_flash_groups, ARRAY_SIZE(mt7981_flash_groups)}, - {"pcie", mt7981_pcie_groups, ARRAY_SIZE(mt7981_pcie_groups)}, -}; - -static const struct mtk_eint_hw mt7981_eint_hw = { - .port_mask = 7, - .ports = 7, - .ap_num = ARRAY_SIZE(mt7981_pins), - .db_cnt = 16, -}; - -static const char * const mt7981_pinctrl_register_base_names[] = { - "gpio", "iocfg_rt", "iocfg_rm", "iocfg_rb", - "iocfg_lb", "iocfg_bl", "iocfg_tm", "iocfg_tl", -}; - -static struct mtk_pin_soc mt7981_data = { - .reg_cal = mt7981_reg_cals, - .pins = mt7981_pins, - .npins = ARRAY_SIZE(mt7981_pins), - .grps = mt7981_groups, - .ngrps = ARRAY_SIZE(mt7981_groups), - .funcs = mt7981_functions, - .nfuncs = ARRAY_SIZE(mt7981_functions), - .eint_hw = &mt7981_eint_hw, - .gpio_m = 0, - .ies_present = false, - .base_names = mt7981_pinctrl_register_base_names, - .nbase_names = ARRAY_SIZE(mt7981_pinctrl_register_base_names), - .bias_disable_set = mtk_pinconf_bias_disable_set, - .bias_disable_get = mtk_pinconf_bias_disable_get, - .bias_set = mtk_pinconf_bias_set, - .bias_get = mtk_pinconf_bias_get, - .pull_type = mt7981_pull_type, - .bias_set_combo = mtk_pinconf_bias_set_combo, - .bias_get_combo = mtk_pinconf_bias_get_combo, - .drive_set = mtk_pinconf_drive_set_rev1, - .drive_get = mtk_pinconf_drive_get_rev1, - .adv_pull_get = mtk_pinconf_adv_pull_get, - .adv_pull_set = mtk_pinconf_adv_pull_set, -}; - -static const struct of_device_id mt7981_pinctrl_of_match[] = { - { .compatible = "mediatek,mt7981-pinctrl", }, - {} -}; - -static int mt7981_pinctrl_probe(struct platform_device *pdev) -{ - return mtk_moore_pinctrl_probe(pdev, &mt7981_data); -} - -static struct platform_driver mt7981_pinctrl_driver = { - .driver = { - .name = "mt7981-pinctrl", - .of_match_table = mt7981_pinctrl_of_match, - }, - .probe = mt7981_pinctrl_probe, -}; - -static int __init mt7981_pinctrl_init(void) -{ - return platform_driver_register(&mt7981_pinctrl_driver); -} -arch_initcall(mt7981_pinctrl_init); diff --git a/target/linux/mediatek/files-5.15/drivers/pinctrl/mediatek/pinctrl-mt7986.c b/target/linux/mediatek/files-5.15/drivers/pinctrl/mediatek/pinctrl-mt7986.c deleted file mode 100644 index acaac9b38a..0000000000 --- a/target/linux/mediatek/files-5.15/drivers/pinctrl/mediatek/pinctrl-mt7986.c +++ /dev/null @@ -1,1011 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * The MT7986 driver based on Linux generic pinctrl binding. - * - * Copyright (C) 2021 MediaTek Inc. - * Author: Sam Shih - */ - -#include "pinctrl-moore.h" - -#define MT7986_PIN(_number, _name) MTK_PIN(_number, _name, 0, _number, DRV_GRP4) -#define MT7986_NOT_BALLOUT_PIN(_number) { .number = _number, .name = NULL } - -#define PIN_FIELD_BASE(_s_pin, _e_pin, _i_base, _s_addr, _x_addrs, _s_bit, \ - _x_bits) \ - PIN_FIELD_CALC(_s_pin, _e_pin, _i_base, _s_addr, _x_addrs, _s_bit, \ - _x_bits, 32, 0) - -/** - * enum - Locking variants of the iocfg bases - * - * MT7986 have multiple bases to program pin configuration listed as the below: - * iocfg_rt:0x11c30000, iocfg_rb:0x11c40000, iocfg_lt:0x11e20000, - * iocfg_lb:0x11e30000, iocfg_tr:0x11f00000, iocfg_tl:0x11f10000, - * _i_based could be used to indicate what base the pin should be mapped into. - * - * Each iocfg register base control different group of pads on the SoC - * - * - * chip carrier - * - * A B C D E F G H - * +------------------------+ - * 8 | o o o o o o o o | - * 7 | o o o o o o o o | - * 6 | o o o o o o o o | - * 5 | o o o o o o o o | - * 4 | o o o o o o o o | - * 3 | o o o o o o o o | - * 2 | o o o o o o o o | - * 1 | o o o o o o o o | - * +------------------------+ - * - * inside Chip carrier - * - * A B C D E F G H - * +------------------------+ - * 8 | | - * 7 | TL TR | - * 6 | +---------+ | - * 5 | LT | | RT | - * 4 | | | | - * 3 | LB | | RB | - * 2 | +---------+ | - * 1 | | - * +------------------------+ - * - */ - -enum { - GPIO_BASE, - IOCFG_RT_BASE, - IOCFG_RB_BASE, - IOCFG_LT_BASE, - IOCFG_LB_BASE, - IOCFG_TR_BASE, - IOCFG_TL_BASE, -}; - -static const char *const mt7986_pinctrl_register_base_names[] = { - "gpio", "iocfg_rt", "iocfg_rb", "iocfg_lt", "iocfg_lb", "iocfg_tr", - "iocfg_tl", -}; - -static const struct mtk_pin_field_calc mt7986_pin_mode_range[] = { - PIN_FIELD(0, 100, 0x300, 0x10, 0, 4), -}; - -static const struct mtk_pin_field_calc mt7986_pin_dir_range[] = { - PIN_FIELD(0, 100, 0x0, 0x10, 0, 1), -}; - -static const struct mtk_pin_field_calc mt7986_pin_di_range[] = { - PIN_FIELD(0, 100, 0x200, 0x10, 0, 1), -}; - -static const struct mtk_pin_field_calc mt7986_pin_do_range[] = { - PIN_FIELD(0, 100, 0x100, 0x10, 0, 1), -}; - -static const struct mtk_pin_field_calc mt7986_pin_ies_range[] = { - PIN_FIELD_BASE(0, 0, IOCFG_RB_BASE, 0x40, 0x10, 17, 1), - PIN_FIELD_BASE(1, 2, IOCFG_LT_BASE, 0x20, 0x10, 10, 1), - PIN_FIELD_BASE(3, 4, IOCFG_LB_BASE, 0x20, 0x10, 0, 1), - PIN_FIELD_BASE(5, 6, IOCFG_RB_BASE, 0x40, 0x10, 0, 1), - PIN_FIELD_BASE(7, 10, IOCFG_LT_BASE, 0x20, 0x10, 0, 1), - PIN_FIELD_BASE(11, 14, IOCFG_RB_BASE, 0x40, 0x10, 8, 1), - PIN_FIELD_BASE(15, 20, IOCFG_RB_BASE, 0x40, 0x10, 2, 1), - PIN_FIELD_BASE(21, 23, IOCFG_RT_BASE, 0x30, 0x10, 12, 1), - PIN_FIELD_BASE(24, 24, IOCFG_RT_BASE, 0x30, 0x10, 18, 1), - PIN_FIELD_BASE(25, 25, IOCFG_RT_BASE, 0x30, 0x10, 17, 1), - PIN_FIELD_BASE(26, 27, IOCFG_RT_BASE, 0x30, 0x10, 15, 1), - PIN_FIELD_BASE(28, 29, IOCFG_RT_BASE, 0x30, 0x10, 19, 1), - PIN_FIELD_BASE(30, 30, IOCFG_RT_BASE, 0x30, 0x10, 23, 1), - PIN_FIELD_BASE(31, 31, IOCFG_RT_BASE, 0x30, 0x10, 22, 1), - PIN_FIELD_BASE(32, 32, IOCFG_RT_BASE, 0x30, 0x10, 21, 1), - PIN_FIELD_BASE(33, 33, IOCFG_LT_BASE, 0x20, 0x10, 4, 1), - PIN_FIELD_BASE(34, 34, IOCFG_LT_BASE, 0x20, 0x10, 8, 1), - PIN_FIELD_BASE(35, 35, IOCFG_LT_BASE, 0x20, 0x10, 7, 1), - PIN_FIELD_BASE(36, 37, IOCFG_LT_BASE, 0x20, 0x10, 5, 1), - PIN_FIELD_BASE(38, 38, IOCFG_LT_BASE, 0x20, 0x10, 9, 1), - PIN_FIELD_BASE(39, 40, IOCFG_RB_BASE, 0x40, 0x10, 18, 1), - PIN_FIELD_BASE(41, 41, IOCFG_RB_BASE, 0x40, 0x10, 12, 1), - PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0x40, 0x10, 22, 1), - PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0x40, 0x10, 20, 1), - PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0x40, 0x10, 26, 1), - PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0x40, 0x10, 24, 1), - PIN_FIELD_BASE(50, 57, IOCFG_RT_BASE, 0x30, 0x10, 2, 1), - PIN_FIELD_BASE(58, 58, IOCFG_RT_BASE, 0x30, 0x10, 1, 1), - PIN_FIELD_BASE(59, 59, IOCFG_RT_BASE, 0x30, 0x10, 0, 1), - PIN_FIELD_BASE(60, 61, IOCFG_RT_BASE, 0x30, 0x10, 10, 1), - PIN_FIELD_BASE(62, 62, IOCFG_RB_BASE, 0x40, 0x10, 15, 1), - PIN_FIELD_BASE(63, 63, IOCFG_RB_BASE, 0x40, 0x10, 14, 1), - PIN_FIELD_BASE(64, 64, IOCFG_RB_BASE, 0x40, 0x10, 13, 1), - PIN_FIELD_BASE(65, 65, IOCFG_RB_BASE, 0x40, 0x10, 16, 1), - PIN_FIELD_BASE(66, 68, IOCFG_LB_BASE, 0x20, 0x10, 2, 1), - PIN_FIELD_BASE(69, 69, IOCFG_TR_BASE, 0x30, 0x10, 1, 1), - PIN_FIELD_BASE(70, 70, IOCFG_TR_BASE, 0x30, 0x10, 0, 1), - PIN_FIELD_BASE(71, 71, IOCFG_TR_BASE, 0x30, 0x10, 16, 1), - PIN_FIELD_BASE(72, 73, IOCFG_TR_BASE, 0x30, 0x10, 14, 1), - PIN_FIELD_BASE(74, 74, IOCFG_TR_BASE, 0x30, 0x10, 4, 1), - PIN_FIELD_BASE(75, 77, IOCFG_TR_BASE, 0x30, 0x10, 6, 1), - PIN_FIELD_BASE(78, 79, IOCFG_TR_BASE, 0x30, 0x10, 2, 1), - PIN_FIELD_BASE(80, 84, IOCFG_TR_BASE, 0x30, 0x10, 9, 1), - PIN_FIELD_BASE(85, 85, IOCFG_TR_BASE, 0x30, 0x10, 5, 1), - PIN_FIELD_BASE(86, 86, IOCFG_TL_BASE, 0x30, 0x10, 1, 1), - PIN_FIELD_BASE(87, 87, IOCFG_TL_BASE, 0x30, 0x10, 0, 1), - PIN_FIELD_BASE(88, 88, IOCFG_TL_BASE, 0x30, 0x10, 14, 1), - PIN_FIELD_BASE(89, 90, IOCFG_TL_BASE, 0x30, 0x10, 12, 1), - PIN_FIELD_BASE(91, 94, IOCFG_TL_BASE, 0x30, 0x10, 4, 1), - PIN_FIELD_BASE(95, 96, IOCFG_TL_BASE, 0x30, 0x10, 2, 1), - PIN_FIELD_BASE(97, 100, IOCFG_TL_BASE, 0x30, 0x10, 8, 1), -}; - -static const struct mtk_pin_field_calc mt7986_pin_smt_range[] = { - PIN_FIELD_BASE(0, 0, IOCFG_RB_BASE, 0xf0, 0x10, 17, 1), - PIN_FIELD_BASE(1, 2, IOCFG_LT_BASE, 0x90, 0x10, 10, 1), - PIN_FIELD_BASE(3, 4, IOCFG_LB_BASE, 0x90, 0x10, 0, 1), - PIN_FIELD_BASE(5, 6, IOCFG_RB_BASE, 0xf0, 0x10, 0, 1), - PIN_FIELD_BASE(7, 10, IOCFG_LT_BASE, 0x90, 0x10, 0, 1), - PIN_FIELD_BASE(11, 14, IOCFG_RB_BASE, 0xf0, 0x10, 8, 1), - PIN_FIELD_BASE(15, 20, IOCFG_RB_BASE, 0xf0, 0x10, 2, 1), - PIN_FIELD_BASE(21, 23, IOCFG_RT_BASE, 0xc0, 0x10, 12, 1), - PIN_FIELD_BASE(24, 24, IOCFG_RT_BASE, 0xc0, 0x10, 18, 1), - PIN_FIELD_BASE(25, 25, IOCFG_RT_BASE, 0xc0, 0x10, 17, 1), - PIN_FIELD_BASE(26, 27, IOCFG_RT_BASE, 0xc0, 0x10, 15, 1), - PIN_FIELD_BASE(28, 29, IOCFG_RT_BASE, 0xc0, 0x10, 19, 1), - PIN_FIELD_BASE(30, 30, IOCFG_RT_BASE, 0xc0, 0x10, 23, 1), - PIN_FIELD_BASE(31, 31, IOCFG_RT_BASE, 0xc0, 0x10, 22, 1), - PIN_FIELD_BASE(32, 32, IOCFG_RT_BASE, 0xc0, 0x10, 21, 1), - PIN_FIELD_BASE(33, 33, IOCFG_LT_BASE, 0x90, 0x10, 4, 1), - PIN_FIELD_BASE(34, 34, IOCFG_LT_BASE, 0x90, 0x10, 8, 1), - PIN_FIELD_BASE(35, 35, IOCFG_LT_BASE, 0x90, 0x10, 7, 1), - PIN_FIELD_BASE(36, 37, IOCFG_LT_BASE, 0x90, 0x10, 5, 1), - PIN_FIELD_BASE(38, 38, IOCFG_LT_BASE, 0x90, 0x10, 9, 1), - PIN_FIELD_BASE(39, 40, IOCFG_RB_BASE, 0xf0, 0x10, 18, 1), - PIN_FIELD_BASE(41, 41, IOCFG_RB_BASE, 0xf0, 0x10, 12, 1), - PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0xf0, 0x10, 22, 1), - PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0xf0, 0x10, 20, 1), - PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0xf0, 0x10, 26, 1), - PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0xf0, 0x10, 24, 1), - PIN_FIELD_BASE(50, 57, IOCFG_RT_BASE, 0xc0, 0x10, 2, 1), - PIN_FIELD_BASE(58, 58, IOCFG_RT_BASE, 0xc0, 0x10, 1, 1), - PIN_FIELD_BASE(59, 59, IOCFG_RT_BASE, 0xc0, 0x10, 0, 1), - PIN_FIELD_BASE(60, 61, IOCFG_RT_BASE, 0xc0, 0x10, 10, 1), - PIN_FIELD_BASE(62, 62, IOCFG_RB_BASE, 0xf0, 0x10, 15, 1), - PIN_FIELD_BASE(63, 63, IOCFG_RB_BASE, 0xf0, 0x10, 14, 1), - PIN_FIELD_BASE(64, 64, IOCFG_RB_BASE, 0xf0, 0x10, 13, 1), - PIN_FIELD_BASE(65, 65, IOCFG_RB_BASE, 0xf0, 0x10, 16, 1), - PIN_FIELD_BASE(66, 68, IOCFG_LB_BASE, 0x90, 0x10, 2, 1), - PIN_FIELD_BASE(69, 69, IOCFG_TR_BASE, 0x80, 0x10, 1, 1), - PIN_FIELD_BASE(70, 70, IOCFG_TR_BASE, 0x80, 0x10, 0, 1), - PIN_FIELD_BASE(71, 71, IOCFG_TR_BASE, 0x80, 0x10, 16, 1), - PIN_FIELD_BASE(72, 73, IOCFG_TR_BASE, 0x80, 0x10, 14, 1), - PIN_FIELD_BASE(74, 74, IOCFG_TR_BASE, 0x80, 0x10, 4, 1), - PIN_FIELD_BASE(75, 77, IOCFG_TR_BASE, 0x80, 0x10, 6, 1), - PIN_FIELD_BASE(78, 79, IOCFG_TR_BASE, 0x80, 0x10, 2, 1), - PIN_FIELD_BASE(80, 84, IOCFG_TR_BASE, 0x80, 0x10, 9, 1), - PIN_FIELD_BASE(85, 85, IOCFG_TR_BASE, 0x80, 0x10, 5, 1), - PIN_FIELD_BASE(86, 86, IOCFG_TL_BASE, 0x70, 0x10, 1, 1), - PIN_FIELD_BASE(87, 87, IOCFG_TL_BASE, 0x70, 0x10, 0, 1), - PIN_FIELD_BASE(88, 88, IOCFG_TL_BASE, 0x70, 0x10, 14, 1), - PIN_FIELD_BASE(89, 90, IOCFG_TL_BASE, 0x70, 0x10, 12, 1), - PIN_FIELD_BASE(91, 94, IOCFG_TL_BASE, 0x70, 0x10, 4, 1), - PIN_FIELD_BASE(95, 96, IOCFG_TL_BASE, 0x70, 0x10, 2, 1), - PIN_FIELD_BASE(97, 100, IOCFG_TL_BASE, 0x70, 0x10, 8, 1), -}; - -static const struct mtk_pin_field_calc mt7986_pin_pu_range[] = { - PIN_FIELD_BASE(69, 69, IOCFG_TR_BASE, 0x50, 0x10, 1, 1), - PIN_FIELD_BASE(70, 70, IOCFG_TR_BASE, 0x50, 0x10, 0, 1), - PIN_FIELD_BASE(71, 71, IOCFG_TR_BASE, 0x50, 0x10, 16, 1), - PIN_FIELD_BASE(72, 73, IOCFG_TR_BASE, 0x50, 0x10, 14, 1), - PIN_FIELD_BASE(74, 74, IOCFG_TR_BASE, 0x50, 0x10, 4, 1), - PIN_FIELD_BASE(75, 77, IOCFG_TR_BASE, 0x50, 0x10, 6, 1), - PIN_FIELD_BASE(78, 79, IOCFG_TR_BASE, 0x50, 0x10, 2, 1), - PIN_FIELD_BASE(80, 84, IOCFG_TR_BASE, 0x50, 0x10, 9, 1), - PIN_FIELD_BASE(85, 85, IOCFG_TR_BASE, 0x50, 0x10, 5, 1), - PIN_FIELD_BASE(86, 86, IOCFG_TL_BASE, 0x50, 0x10, 1, 1), - PIN_FIELD_BASE(87, 87, IOCFG_TL_BASE, 0x50, 0x10, 0, 1), - PIN_FIELD_BASE(88, 88, IOCFG_TL_BASE, 0x50, 0x10, 14, 1), - PIN_FIELD_BASE(89, 90, IOCFG_TL_BASE, 0x50, 0x10, 12, 1), - PIN_FIELD_BASE(91, 94, IOCFG_TL_BASE, 0x50, 0x10, 4, 1), - PIN_FIELD_BASE(95, 96, IOCFG_TL_BASE, 0x50, 0x10, 2, 1), - PIN_FIELD_BASE(97, 100, IOCFG_TL_BASE, 0x50, 0x10, 8, 1), -}; - -static const struct mtk_pin_field_calc mt7986_pin_pd_range[] = { - PIN_FIELD_BASE(69, 69, IOCFG_TR_BASE, 0x40, 0x10, 1, 1), - PIN_FIELD_BASE(70, 70, IOCFG_TR_BASE, 0x40, 0x10, 0, 1), - PIN_FIELD_BASE(71, 71, IOCFG_TR_BASE, 0x40, 0x10, 16, 1), - PIN_FIELD_BASE(72, 73, IOCFG_TR_BASE, 0x40, 0x10, 14, 1), - PIN_FIELD_BASE(74, 74, IOCFG_TR_BASE, 0x40, 0x10, 4, 1), - PIN_FIELD_BASE(75, 77, IOCFG_TR_BASE, 0x40, 0x10, 6, 1), - PIN_FIELD_BASE(78, 79, IOCFG_TR_BASE, 0x40, 0x10, 2, 1), - PIN_FIELD_BASE(80, 84, IOCFG_TR_BASE, 0x40, 0x10, 9, 1), - PIN_FIELD_BASE(85, 85, IOCFG_TR_BASE, 0x40, 0x10, 5, 1), - PIN_FIELD_BASE(86, 86, IOCFG_TL_BASE, 0x40, 0x10, 1, 1), - PIN_FIELD_BASE(87, 87, IOCFG_TL_BASE, 0x40, 0x10, 0, 1), - PIN_FIELD_BASE(88, 88, IOCFG_TL_BASE, 0x40, 0x10, 14, 1), - PIN_FIELD_BASE(89, 90, IOCFG_TL_BASE, 0x40, 0x10, 12, 1), - PIN_FIELD_BASE(91, 94, IOCFG_TL_BASE, 0x40, 0x10, 4, 1), - PIN_FIELD_BASE(95, 96, IOCFG_TL_BASE, 0x40, 0x10, 2, 1), - PIN_FIELD_BASE(97, 100, IOCFG_TL_BASE, 0x40, 0x10, 8, 1), -}; - -static const struct mtk_pin_field_calc mt7986_pin_drv_range[] = { - PIN_FIELD_BASE(0, 0, IOCFG_RB_BASE, 0x10, 0x10, 21, 3), - PIN_FIELD_BASE(1, 2, IOCFG_LT_BASE, 0x10, 0x10, 0, 3), - PIN_FIELD_BASE(3, 4, IOCFG_LB_BASE, 0x00, 0x10, 0, 1), - PIN_FIELD_BASE(5, 5, IOCFG_RB_BASE, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(6, 6, IOCFG_RB_BASE, 0x00, 0x10, 21, 3), - PIN_FIELD_BASE(7, 10, IOCFG_LT_BASE, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(11, 12, IOCFG_RB_BASE, 0x00, 0x10, 24, 3), - PIN_FIELD_BASE(13, 14, IOCFG_RB_BASE, 0x10, 0x10, 0, 3), - PIN_FIELD_BASE(15, 20, IOCFG_RB_BASE, 0x00, 0x10, 3, 3), - PIN_FIELD_BASE(21, 23, IOCFG_RT_BASE, 0x10, 0x10, 6, 3), - PIN_FIELD_BASE(24, 24, IOCFG_RT_BASE, 0x10, 0x10, 24, 3), - PIN_FIELD_BASE(25, 25, IOCFG_RT_BASE, 0x10, 0x10, 21, 3), - PIN_FIELD_BASE(26, 27, IOCFG_RT_BASE, 0x10, 0x10, 15, 3), - PIN_FIELD_BASE(28, 28, IOCFG_RT_BASE, 0x10, 0x10, 27, 3), - PIN_FIELD_BASE(29, 29, IOCFG_RT_BASE, 0x20, 0x10, 0, 3), - PIN_FIELD_BASE(30, 30, IOCFG_RT_BASE, 0x20, 0x10, 9, 3), - PIN_FIELD_BASE(31, 31, IOCFG_RT_BASE, 0x20, 0x10, 6, 3), - PIN_FIELD_BASE(32, 32, IOCFG_RT_BASE, 0x20, 0x10, 3, 3), - PIN_FIELD_BASE(33, 33, IOCFG_LT_BASE, 0x00, 0x10, 12, 3), - PIN_FIELD_BASE(34, 34, IOCFG_LT_BASE, 0x00, 0x10, 24, 3), - PIN_FIELD_BASE(35, 35, IOCFG_LT_BASE, 0x00, 0x10, 21, 3), - PIN_FIELD_BASE(36, 37, IOCFG_LT_BASE, 0x00, 0x10, 15, 3), - PIN_FIELD_BASE(38, 38, IOCFG_LT_BASE, 0x00, 0x10, 27, 3), - PIN_FIELD_BASE(39, 39, IOCFG_RB_BASE, 0x10, 0x10, 27, 3), - PIN_FIELD_BASE(40, 40, IOCFG_RB_BASE, 0x20, 0x10, 0, 3), - PIN_FIELD_BASE(41, 41, IOCFG_RB_BASE, 0x10, 0x10, 6, 3), - PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0x20, 0x10, 9, 3), - PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0x20, 0x10, 3, 3), - PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0x20, 0x10, 21, 3), - PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0x20, 0x10, 15, 3), - PIN_FIELD_BASE(50, 57, IOCFG_RT_BASE, 0x00, 0x10, 6, 3), - PIN_FIELD_BASE(58, 58, IOCFG_RT_BASE, 0x00, 0x10, 3, 3), - PIN_FIELD_BASE(59, 59, IOCFG_RT_BASE, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(60, 61, IOCFG_RT_BASE, 0x10, 0x10, 0, 3), - PIN_FIELD_BASE(62, 62, IOCFG_RB_BASE, 0x10, 0x10, 15, 3), - PIN_FIELD_BASE(63, 63, IOCFG_RB_BASE, 0x10, 0x10, 12, 3), - PIN_FIELD_BASE(64, 64, IOCFG_RB_BASE, 0x10, 0x10, 9, 3), - PIN_FIELD_BASE(65, 65, IOCFG_RB_BASE, 0x10, 0x10, 18, 3), - PIN_FIELD_BASE(66, 68, IOCFG_LB_BASE, 0x00, 0x10, 2, 3), - PIN_FIELD_BASE(69, 69, IOCFG_TR_BASE, 0x00, 0x10, 3, 3), - PIN_FIELD_BASE(70, 70, IOCFG_TR_BASE, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(71, 71, IOCFG_TR_BASE, 0x10, 0x10, 18, 3), - PIN_FIELD_BASE(72, 73, IOCFG_TR_BASE, 0x10, 0x10, 12, 3), - PIN_FIELD_BASE(74, 77, IOCFG_TR_BASE, 0x00, 0x10, 15, 3), - PIN_FIELD_BASE(78, 79, IOCFG_TR_BASE, 0x00, 0x10, 6, 3), - PIN_FIELD_BASE(80, 80, IOCFG_TR_BASE, 0x00, 0x10, 27, 3), - PIN_FIELD_BASE(81, 84, IOCFG_TR_BASE, 0x10, 0x10, 0, 3), - PIN_FIELD_BASE(85, 85, IOCFG_TR_BASE, 0x00, 0x10, 12, 3), - PIN_FIELD_BASE(86, 86, IOCFG_TL_BASE, 0x00, 0x10, 3, 3), - PIN_FIELD_BASE(87, 87, IOCFG_TL_BASE, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(88, 88, IOCFG_TL_BASE, 0x10, 0x10, 12, 3), - PIN_FIELD_BASE(89, 90, IOCFG_TL_BASE, 0x10, 0x10, 6, 3), - PIN_FIELD_BASE(91, 94, IOCFG_TL_BASE, 0x00, 0x10, 12, 3), - PIN_FIELD_BASE(95, 96, IOCFG_TL_BASE, 0x00, 0x10, 6, 3), - PIN_FIELD_BASE(97, 98, IOCFG_TL_BASE, 0x00, 0x10, 24, 3), - PIN_FIELD_BASE(99, 100, IOCFG_TL_BASE, 0x10, 0x10, 2, 3), -}; - -static const struct mtk_pin_field_calc mt7986_pin_pupd_range[] = { - PIN_FIELD_BASE(0, 0, IOCFG_RB_BASE, 0x60, 0x10, 17, 1), - PIN_FIELD_BASE(1, 2, IOCFG_LT_BASE, 0x30, 0x10, 10, 1), - PIN_FIELD_BASE(3, 4, IOCFG_LB_BASE, 0x40, 0x10, 0, 1), - PIN_FIELD_BASE(5, 6, IOCFG_RB_BASE, 0x60, 0x10, 0, 1), - PIN_FIELD_BASE(7, 10, IOCFG_LT_BASE, 0x30, 0x10, 0, 1), - PIN_FIELD_BASE(11, 14, IOCFG_RB_BASE, 0x60, 0x10, 8, 1), - PIN_FIELD_BASE(15, 20, IOCFG_RB_BASE, 0x60, 0x10, 2, 1), - PIN_FIELD_BASE(21, 23, IOCFG_RT_BASE, 0x40, 0x10, 12, 1), - PIN_FIELD_BASE(24, 24, IOCFG_RT_BASE, 0x40, 0x10, 18, 1), - PIN_FIELD_BASE(25, 25, IOCFG_RT_BASE, 0x40, 0x10, 17, 1), - PIN_FIELD_BASE(26, 27, IOCFG_RT_BASE, 0x40, 0x10, 15, 1), - PIN_FIELD_BASE(28, 29, IOCFG_RT_BASE, 0x40, 0x10, 19, 1), - PIN_FIELD_BASE(30, 30, IOCFG_RT_BASE, 0x40, 0x10, 23, 1), - PIN_FIELD_BASE(31, 31, IOCFG_RT_BASE, 0x40, 0x10, 22, 1), - PIN_FIELD_BASE(32, 32, IOCFG_RT_BASE, 0x40, 0x10, 21, 1), - PIN_FIELD_BASE(33, 33, IOCFG_LT_BASE, 0x30, 0x10, 4, 1), - PIN_FIELD_BASE(34, 34, IOCFG_LT_BASE, 0x30, 0x10, 8, 1), - PIN_FIELD_BASE(35, 35, IOCFG_LT_BASE, 0x30, 0x10, 7, 1), - PIN_FIELD_BASE(36, 37, IOCFG_LT_BASE, 0x30, 0x10, 5, 1), - PIN_FIELD_BASE(38, 38, IOCFG_LT_BASE, 0x30, 0x10, 9, 1), - PIN_FIELD_BASE(39, 40, IOCFG_RB_BASE, 0x60, 0x10, 18, 1), - PIN_FIELD_BASE(41, 41, IOCFG_RB_BASE, 0x60, 0x10, 12, 1), - PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0x60, 0x10, 23, 1), - PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0x60, 0x10, 21, 1), - PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0x60, 0x10, 27, 1), - PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0x60, 0x10, 25, 1), - PIN_FIELD_BASE(50, 57, IOCFG_RT_BASE, 0x40, 0x10, 2, 1), - PIN_FIELD_BASE(58, 58, IOCFG_RT_BASE, 0x40, 0x10, 1, 1), - PIN_FIELD_BASE(59, 59, IOCFG_RT_BASE, 0x40, 0x10, 0, 1), - PIN_FIELD_BASE(60, 61, IOCFG_RT_BASE, 0x40, 0x10, 10, 1), - PIN_FIELD_BASE(62, 62, IOCFG_RB_BASE, 0x60, 0x10, 15, 1), - PIN_FIELD_BASE(63, 63, IOCFG_RB_BASE, 0x60, 0x10, 14, 1), - PIN_FIELD_BASE(64, 64, IOCFG_RB_BASE, 0x60, 0x10, 13, 1), - PIN_FIELD_BASE(65, 65, IOCFG_RB_BASE, 0x60, 0x10, 16, 1), - PIN_FIELD_BASE(66, 68, IOCFG_LB_BASE, 0x40, 0x10, 2, 1), -}; - -static const struct mtk_pin_field_calc mt7986_pin_r0_range[] = { - PIN_FIELD_BASE(0, 0, IOCFG_RB_BASE, 0x70, 0x10, 17, 1), - PIN_FIELD_BASE(1, 2, IOCFG_LT_BASE, 0x40, 0x10, 10, 1), - PIN_FIELD_BASE(3, 4, IOCFG_LB_BASE, 0x50, 0x10, 0, 1), - PIN_FIELD_BASE(5, 6, IOCFG_RB_BASE, 0x70, 0x10, 0, 1), - PIN_FIELD_BASE(7, 10, IOCFG_LT_BASE, 0x40, 0x10, 0, 1), - PIN_FIELD_BASE(11, 14, IOCFG_RB_BASE, 0x70, 0x10, 8, 1), - PIN_FIELD_BASE(15, 20, IOCFG_RB_BASE, 0x70, 0x10, 2, 1), - PIN_FIELD_BASE(21, 23, IOCFG_RT_BASE, 0x50, 0x10, 12, 1), - PIN_FIELD_BASE(24, 24, IOCFG_RT_BASE, 0x50, 0x10, 18, 1), - PIN_FIELD_BASE(25, 25, IOCFG_RT_BASE, 0x50, 0x10, 17, 1), - PIN_FIELD_BASE(26, 27, IOCFG_RT_BASE, 0x50, 0x10, 15, 1), - PIN_FIELD_BASE(28, 29, IOCFG_RT_BASE, 0x50, 0x10, 19, 1), - PIN_FIELD_BASE(30, 30, IOCFG_RT_BASE, 0x50, 0x10, 23, 1), - PIN_FIELD_BASE(31, 31, IOCFG_RT_BASE, 0x50, 0x10, 22, 1), - PIN_FIELD_BASE(32, 32, IOCFG_RT_BASE, 0x50, 0x10, 21, 1), - PIN_FIELD_BASE(33, 33, IOCFG_LT_BASE, 0x40, 0x10, 4, 1), - PIN_FIELD_BASE(34, 34, IOCFG_LT_BASE, 0x40, 0x10, 8, 1), - PIN_FIELD_BASE(35, 35, IOCFG_LT_BASE, 0x40, 0x10, 7, 1), - PIN_FIELD_BASE(36, 37, IOCFG_LT_BASE, 0x40, 0x10, 5, 1), - PIN_FIELD_BASE(38, 38, IOCFG_LT_BASE, 0x40, 0x10, 9, 1), - PIN_FIELD_BASE(39, 40, IOCFG_RB_BASE, 0x70, 0x10, 18, 1), - PIN_FIELD_BASE(41, 41, IOCFG_RB_BASE, 0x70, 0x10, 12, 1), - PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0x70, 0x10, 23, 1), - PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0x70, 0x10, 21, 1), - PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0x70, 0x10, 27, 1), - PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0x70, 0x10, 25, 1), - PIN_FIELD_BASE(50, 57, IOCFG_RT_BASE, 0x50, 0x10, 2, 1), - PIN_FIELD_BASE(58, 58, IOCFG_RT_BASE, 0x50, 0x10, 1, 1), - PIN_FIELD_BASE(59, 59, IOCFG_RT_BASE, 0x50, 0x10, 0, 1), - PIN_FIELD_BASE(60, 61, IOCFG_RT_BASE, 0x50, 0x10, 10, 1), - PIN_FIELD_BASE(62, 62, IOCFG_RB_BASE, 0x70, 0x10, 15, 1), - PIN_FIELD_BASE(63, 63, IOCFG_RB_BASE, 0x70, 0x10, 14, 1), - PIN_FIELD_BASE(64, 64, IOCFG_RB_BASE, 0x70, 0x10, 13, 1), - PIN_FIELD_BASE(65, 65, IOCFG_RB_BASE, 0x70, 0x10, 16, 1), - PIN_FIELD_BASE(66, 68, IOCFG_LB_BASE, 0x50, 0x10, 2, 1), -}; - -static const struct mtk_pin_field_calc mt7986_pin_r1_range[] = { - PIN_FIELD_BASE(0, 0, IOCFG_RB_BASE, 0x80, 0x10, 17, 1), - PIN_FIELD_BASE(1, 2, IOCFG_LT_BASE, 0x50, 0x10, 10, 1), - PIN_FIELD_BASE(3, 4, IOCFG_LB_BASE, 0x60, 0x10, 0, 1), - PIN_FIELD_BASE(5, 6, IOCFG_RB_BASE, 0x80, 0x10, 0, 1), - PIN_FIELD_BASE(7, 10, IOCFG_LT_BASE, 0x50, 0x10, 0, 1), - PIN_FIELD_BASE(11, 14, IOCFG_RB_BASE, 0x80, 0x10, 8, 1), - PIN_FIELD_BASE(15, 20, IOCFG_RB_BASE, 0x80, 0x10, 2, 1), - PIN_FIELD_BASE(21, 23, IOCFG_RT_BASE, 0x60, 0x10, 12, 1), - PIN_FIELD_BASE(24, 24, IOCFG_RT_BASE, 0x60, 0x10, 18, 1), - PIN_FIELD_BASE(25, 25, IOCFG_RT_BASE, 0x60, 0x10, 17, 1), - PIN_FIELD_BASE(26, 27, IOCFG_RT_BASE, 0x60, 0x10, 15, 1), - PIN_FIELD_BASE(28, 29, IOCFG_RT_BASE, 0x60, 0x10, 19, 1), - PIN_FIELD_BASE(30, 30, IOCFG_RT_BASE, 0x60, 0x10, 23, 1), - PIN_FIELD_BASE(31, 31, IOCFG_RT_BASE, 0x60, 0x10, 22, 1), - PIN_FIELD_BASE(32, 32, IOCFG_RT_BASE, 0x60, 0x10, 21, 1), - PIN_FIELD_BASE(33, 33, IOCFG_LT_BASE, 0x50, 0x10, 4, 1), - PIN_FIELD_BASE(34, 34, IOCFG_LT_BASE, 0x50, 0x10, 8, 1), - PIN_FIELD_BASE(35, 35, IOCFG_LT_BASE, 0x50, 0x10, 7, 1), - PIN_FIELD_BASE(36, 37, IOCFG_LT_BASE, 0x50, 0x10, 5, 1), - PIN_FIELD_BASE(38, 38, IOCFG_LT_BASE, 0x50, 0x10, 9, 1), - PIN_FIELD_BASE(39, 40, IOCFG_RB_BASE, 0x80, 0x10, 18, 1), - PIN_FIELD_BASE(41, 41, IOCFG_RB_BASE, 0x80, 0x10, 12, 1), - PIN_FIELD_BASE(42, 43, IOCFG_RB_BASE, 0x80, 0x10, 23, 1), - PIN_FIELD_BASE(44, 45, IOCFG_RB_BASE, 0x80, 0x10, 21, 1), - PIN_FIELD_BASE(46, 47, IOCFG_RB_BASE, 0x80, 0x10, 27, 1), - PIN_FIELD_BASE(48, 49, IOCFG_RB_BASE, 0x80, 0x10, 25, 1), - PIN_FIELD_BASE(50, 57, IOCFG_RT_BASE, 0x60, 0x10, 2, 1), - PIN_FIELD_BASE(58, 58, IOCFG_RT_BASE, 0x60, 0x10, 1, 1), - PIN_FIELD_BASE(59, 59, IOCFG_RT_BASE, 0x60, 0x10, 0, 1), - PIN_FIELD_BASE(60, 61, IOCFG_RT_BASE, 0x60, 0x10, 10, 1), - PIN_FIELD_BASE(62, 62, IOCFG_RB_BASE, 0x80, 0x10, 15, 1), - PIN_FIELD_BASE(63, 63, IOCFG_RB_BASE, 0x80, 0x10, 14, 1), - PIN_FIELD_BASE(64, 64, IOCFG_RB_BASE, 0x80, 0x10, 13, 1), - PIN_FIELD_BASE(65, 65, IOCFG_RB_BASE, 0x80, 0x10, 16, 1), - PIN_FIELD_BASE(66, 68, IOCFG_LB_BASE, 0x60, 0x10, 2, 1), -}; - -static const unsigned int mt7986_pull_type[] = { - MTK_PULL_PUPD_R1R0_TYPE,/*0*/ MTK_PULL_PUPD_R1R0_TYPE,/*1*/ - MTK_PULL_PUPD_R1R0_TYPE,/*2*/ MTK_PULL_PUPD_R1R0_TYPE,/*3*/ - MTK_PULL_PUPD_R1R0_TYPE,/*4*/ MTK_PULL_PUPD_R1R0_TYPE,/*5*/ - MTK_PULL_PUPD_R1R0_TYPE,/*6*/ MTK_PULL_PUPD_R1R0_TYPE,/*7*/ - MTK_PULL_PUPD_R1R0_TYPE,/*8*/ MTK_PULL_PUPD_R1R0_TYPE,/*9*/ - MTK_PULL_PUPD_R1R0_TYPE,/*10*/ MTK_PULL_PUPD_R1R0_TYPE,/*11*/ - MTK_PULL_PUPD_R1R0_TYPE,/*12*/ MTK_PULL_PUPD_R1R0_TYPE,/*13*/ - MTK_PULL_PUPD_R1R0_TYPE,/*14*/ MTK_PULL_PUPD_R1R0_TYPE,/*15*/ - MTK_PULL_PUPD_R1R0_TYPE,/*16*/ MTK_PULL_PUPD_R1R0_TYPE,/*17*/ - MTK_PULL_PUPD_R1R0_TYPE,/*18*/ MTK_PULL_PUPD_R1R0_TYPE,/*19*/ - MTK_PULL_PUPD_R1R0_TYPE,/*20*/ MTK_PULL_PUPD_R1R0_TYPE,/*21*/ - MTK_PULL_PUPD_R1R0_TYPE,/*22*/ MTK_PULL_PUPD_R1R0_TYPE,/*23*/ - MTK_PULL_PUPD_R1R0_TYPE,/*24*/ MTK_PULL_PUPD_R1R0_TYPE,/*25*/ - MTK_PULL_PUPD_R1R0_TYPE,/*26*/ MTK_PULL_PUPD_R1R0_TYPE,/*27*/ - MTK_PULL_PUPD_R1R0_TYPE,/*28*/ MTK_PULL_PUPD_R1R0_TYPE,/*29*/ - MTK_PULL_PUPD_R1R0_TYPE,/*30*/ MTK_PULL_PUPD_R1R0_TYPE,/*31*/ - MTK_PULL_PUPD_R1R0_TYPE,/*32*/ MTK_PULL_PUPD_R1R0_TYPE,/*33*/ - MTK_PULL_PUPD_R1R0_TYPE,/*34*/ MTK_PULL_PUPD_R1R0_TYPE,/*35*/ - MTK_PULL_PUPD_R1R0_TYPE,/*36*/ MTK_PULL_PUPD_R1R0_TYPE,/*37*/ - MTK_PULL_PUPD_R1R0_TYPE,/*38*/ MTK_PULL_PUPD_R1R0_TYPE,/*39*/ - MTK_PULL_PUPD_R1R0_TYPE,/*40*/ MTK_PULL_PUPD_R1R0_TYPE,/*41*/ - MTK_PULL_PUPD_R1R0_TYPE,/*42*/ MTK_PULL_PUPD_R1R0_TYPE,/*43*/ - MTK_PULL_PUPD_R1R0_TYPE,/*44*/ MTK_PULL_PUPD_R1R0_TYPE,/*45*/ - MTK_PULL_PUPD_R1R0_TYPE,/*46*/ MTK_PULL_PUPD_R1R0_TYPE,/*47*/ - MTK_PULL_PUPD_R1R0_TYPE,/*48*/ MTK_PULL_PUPD_R1R0_TYPE,/*49*/ - MTK_PULL_PUPD_R1R0_TYPE,/*50*/ MTK_PULL_PUPD_R1R0_TYPE,/*51*/ - MTK_PULL_PUPD_R1R0_TYPE,/*52*/ MTK_PULL_PUPD_R1R0_TYPE,/*53*/ - MTK_PULL_PUPD_R1R0_TYPE,/*54*/ MTK_PULL_PUPD_R1R0_TYPE,/*55*/ - MTK_PULL_PUPD_R1R0_TYPE,/*56*/ MTK_PULL_PUPD_R1R0_TYPE,/*57*/ - MTK_PULL_PUPD_R1R0_TYPE,/*58*/ MTK_PULL_PUPD_R1R0_TYPE,/*59*/ - MTK_PULL_PUPD_R1R0_TYPE,/*60*/ MTK_PULL_PUPD_R1R0_TYPE,/*61*/ - MTK_PULL_PUPD_R1R0_TYPE,/*62*/ MTK_PULL_PUPD_R1R0_TYPE,/*63*/ - MTK_PULL_PUPD_R1R0_TYPE,/*64*/ MTK_PULL_PUPD_R1R0_TYPE,/*65*/ - MTK_PULL_PUPD_R1R0_TYPE,/*66*/ MTK_PULL_PUPD_R1R0_TYPE,/*67*/ - MTK_PULL_PUPD_R1R0_TYPE,/*68*/ MTK_PULL_PU_PD_TYPE,/*69*/ - MTK_PULL_PU_PD_TYPE,/*70*/ MTK_PULL_PU_PD_TYPE,/*71*/ - MTK_PULL_PU_PD_TYPE,/*72*/ MTK_PULL_PU_PD_TYPE,/*73*/ - MTK_PULL_PU_PD_TYPE,/*74*/ MTK_PULL_PU_PD_TYPE,/*75*/ - MTK_PULL_PU_PD_TYPE,/*76*/ MTK_PULL_PU_PD_TYPE,/*77*/ - MTK_PULL_PU_PD_TYPE,/*78*/ MTK_PULL_PU_PD_TYPE,/*79*/ - MTK_PULL_PU_PD_TYPE,/*80*/ MTK_PULL_PU_PD_TYPE,/*81*/ - MTK_PULL_PU_PD_TYPE,/*82*/ MTK_PULL_PU_PD_TYPE,/*83*/ - MTK_PULL_PU_PD_TYPE,/*84*/ MTK_PULL_PU_PD_TYPE,/*85*/ - MTK_PULL_PU_PD_TYPE,/*86*/ MTK_PULL_PU_PD_TYPE,/*87*/ - MTK_PULL_PU_PD_TYPE,/*88*/ MTK_PULL_PU_PD_TYPE,/*89*/ - MTK_PULL_PU_PD_TYPE,/*90*/ MTK_PULL_PU_PD_TYPE,/*91*/ - MTK_PULL_PU_PD_TYPE,/*92*/ MTK_PULL_PU_PD_TYPE,/*93*/ - MTK_PULL_PU_PD_TYPE,/*94*/ MTK_PULL_PU_PD_TYPE,/*95*/ - MTK_PULL_PU_PD_TYPE,/*96*/ MTK_PULL_PU_PD_TYPE,/*97*/ - MTK_PULL_PU_PD_TYPE,/*98*/ MTK_PULL_PU_PD_TYPE,/*99*/ - MTK_PULL_PU_PD_TYPE,/*100*/ -}; - -static const struct mtk_pin_reg_calc mt7986_reg_cals[] = { - [PINCTRL_PIN_REG_MODE] = MTK_RANGE(mt7986_pin_mode_range), - [PINCTRL_PIN_REG_DIR] = MTK_RANGE(mt7986_pin_dir_range), - [PINCTRL_PIN_REG_DI] = MTK_RANGE(mt7986_pin_di_range), - [PINCTRL_PIN_REG_DO] = MTK_RANGE(mt7986_pin_do_range), - [PINCTRL_PIN_REG_SMT] = MTK_RANGE(mt7986_pin_smt_range), - [PINCTRL_PIN_REG_IES] = MTK_RANGE(mt7986_pin_ies_range), - [PINCTRL_PIN_REG_DRV] = MTK_RANGE(mt7986_pin_drv_range), - [PINCTRL_PIN_REG_PU] = MTK_RANGE(mt7986_pin_pu_range), - [PINCTRL_PIN_REG_PD] = MTK_RANGE(mt7986_pin_pd_range), - [PINCTRL_PIN_REG_PUPD] = MTK_RANGE(mt7986_pin_pupd_range), - [PINCTRL_PIN_REG_R0] = MTK_RANGE(mt7986_pin_r0_range), - [PINCTRL_PIN_REG_R1] = MTK_RANGE(mt7986_pin_r1_range), -}; - -static const struct mtk_pin_desc mt7986a_pins[] = { - MT7986_PIN(0, "SYS_WATCHDOG"), - MT7986_PIN(1, "WF2G_LED"), - MT7986_PIN(2, "WF5G_LED"), - MT7986_PIN(3, "I2C_SCL"), - MT7986_PIN(4, "I2C_SDA"), - MT7986_PIN(5, "GPIO_0"), - MT7986_PIN(6, "GPIO_1"), - MT7986_PIN(7, "GPIO_2"), - MT7986_PIN(8, "GPIO_3"), - MT7986_PIN(9, "GPIO_4"), - MT7986_PIN(10, "GPIO_5"), - MT7986_PIN(11, "GPIO_6"), - MT7986_PIN(12, "GPIO_7"), - MT7986_PIN(13, "GPIO_8"), - MT7986_PIN(14, "GPIO_9"), - MT7986_PIN(15, "GPIO_10"), - MT7986_PIN(16, "GPIO_11"), - MT7986_PIN(17, "GPIO_12"), - MT7986_PIN(18, "GPIO_13"), - MT7986_PIN(19, "GPIO_14"), - MT7986_PIN(20, "GPIO_15"), - MT7986_PIN(21, "PWM0"), - MT7986_PIN(22, "PWM1"), - MT7986_PIN(23, "SPI0_CLK"), - MT7986_PIN(24, "SPI0_MOSI"), - MT7986_PIN(25, "SPI0_MISO"), - MT7986_PIN(26, "SPI0_CS"), - MT7986_PIN(27, "SPI0_HOLD"), - MT7986_PIN(28, "SPI0_WP"), - MT7986_PIN(29, "SPI1_CLK"), - MT7986_PIN(30, "SPI1_MOSI"), - MT7986_PIN(31, "SPI1_MISO"), - MT7986_PIN(32, "SPI1_CS"), - MT7986_PIN(33, "SPI2_CLK"), - MT7986_PIN(34, "SPI2_MOSI"), - MT7986_PIN(35, "SPI2_MISO"), - MT7986_PIN(36, "SPI2_CS"), - MT7986_PIN(37, "SPI2_HOLD"), - MT7986_PIN(38, "SPI2_WP"), - MT7986_PIN(39, "UART0_RXD"), - MT7986_PIN(40, "UART0_TXD"), - MT7986_PIN(41, "PCIE_PERESET_N"), - MT7986_PIN(42, "UART1_RXD"), - MT7986_PIN(43, "UART1_TXD"), - MT7986_PIN(44, "UART1_CTS"), - MT7986_PIN(45, "UART1_RTS"), - MT7986_PIN(46, "UART2_RXD"), - MT7986_PIN(47, "UART2_TXD"), - MT7986_PIN(48, "UART2_CTS"), - MT7986_PIN(49, "UART2_RTS"), - MT7986_PIN(50, "EMMC_DATA_0"), - MT7986_PIN(51, "EMMC_DATA_1"), - MT7986_PIN(52, "EMMC_DATA_2"), - MT7986_PIN(53, "EMMC_DATA_3"), - MT7986_PIN(54, "EMMC_DATA_4"), - MT7986_PIN(55, "EMMC_DATA_5"), - MT7986_PIN(56, "EMMC_DATA_6"), - MT7986_PIN(57, "EMMC_DATA_7"), - MT7986_PIN(58, "EMMC_CMD"), - MT7986_PIN(59, "EMMC_CK"), - MT7986_PIN(60, "EMMC_DSL"), - MT7986_PIN(61, "EMMC_RSTB"), - MT7986_PIN(62, "PCM_DTX"), - MT7986_PIN(63, "PCM_DRX"), - MT7986_PIN(64, "PCM_CLK"), - MT7986_PIN(65, "PCM_FS"), - MT7986_PIN(66, "MT7531_INT"), - MT7986_PIN(67, "SMI_MDC"), - MT7986_PIN(68, "SMI_MDIO"), - MT7986_PIN(69, "WF0_DIG_RESETB"), - MT7986_PIN(70, "WF0_CBA_RESETB"), - MT7986_PIN(71, "WF0_XO_REQ"), - MT7986_PIN(72, "WF0_TOP_CLK"), - MT7986_PIN(73, "WF0_TOP_DATA"), - MT7986_PIN(74, "WF0_HB1"), - MT7986_PIN(75, "WF0_HB2"), - MT7986_PIN(76, "WF0_HB3"), - MT7986_PIN(77, "WF0_HB4"), - MT7986_PIN(78, "WF0_HB0"), - MT7986_PIN(79, "WF0_HB0_B"), - MT7986_PIN(80, "WF0_HB5"), - MT7986_PIN(81, "WF0_HB6"), - MT7986_PIN(82, "WF0_HB7"), - MT7986_PIN(83, "WF0_HB8"), - MT7986_PIN(84, "WF0_HB9"), - MT7986_PIN(85, "WF0_HB10"), - MT7986_PIN(86, "WF1_DIG_RESETB"), - MT7986_PIN(87, "WF1_CBA_RESETB"), - MT7986_PIN(88, "WF1_XO_REQ"), - MT7986_PIN(89, "WF1_TOP_CLK"), - MT7986_PIN(90, "WF1_TOP_DATA"), - MT7986_PIN(91, "WF1_HB1"), - MT7986_PIN(92, "WF1_HB2"), - MT7986_PIN(93, "WF1_HB3"), - MT7986_PIN(94, "WF1_HB4"), - MT7986_PIN(95, "WF1_HB0"), - MT7986_PIN(96, "WF1_HB0_B"), - MT7986_PIN(97, "WF1_HB5"), - MT7986_PIN(98, "WF1_HB6"), - MT7986_PIN(99, "WF1_HB7"), - MT7986_PIN(100, "WF1_HB8"), -}; - -static const struct mtk_pin_desc mt7986b_pins[] = { - MT7986_PIN(0, "SYS_WATCHDOG"), - MT7986_PIN(1, "WF2G_LED"), - MT7986_PIN(2, "WF5G_LED"), - MT7986_PIN(3, "I2C_SCL"), - MT7986_PIN(4, "I2C_SDA"), - MT7986_PIN(5, "GPIO_0"), - MT7986_PIN(6, "GPIO_1"), - MT7986_PIN(7, "GPIO_2"), - MT7986_PIN(8, "GPIO_3"), - MT7986_PIN(9, "GPIO_4"), - MT7986_PIN(10, "GPIO_5"), - MT7986_PIN(11, "GPIO_6"), - MT7986_PIN(12, "GPIO_7"), - MT7986_PIN(13, "GPIO_8"), - MT7986_PIN(14, "GPIO_9"), - MT7986_PIN(15, "GPIO_10"), - MT7986_PIN(16, "GPIO_11"), - MT7986_PIN(17, "GPIO_12"), - MT7986_PIN(18, "GPIO_13"), - MT7986_PIN(19, "GPIO_14"), - MT7986_PIN(20, "GPIO_15"), - MT7986_PIN(21, "PWM0"), - MT7986_PIN(22, "PWM1"), - MT7986_PIN(23, "SPI0_CLK"), - MT7986_PIN(24, "SPI0_MOSI"), - MT7986_PIN(25, "SPI0_MISO"), - MT7986_PIN(26, "SPI0_CS"), - MT7986_PIN(27, "SPI0_HOLD"), - MT7986_PIN(28, "SPI0_WP"), - MT7986_PIN(29, "SPI1_CLK"), - MT7986_PIN(30, "SPI1_MOSI"), - MT7986_PIN(31, "SPI1_MISO"), - MT7986_PIN(32, "SPI1_CS"), - MT7986_PIN(33, "SPI2_CLK"), - MT7986_PIN(34, "SPI2_MOSI"), - MT7986_PIN(35, "SPI2_MISO"), - MT7986_PIN(36, "SPI2_CS"), - MT7986_PIN(37, "SPI2_HOLD"), - MT7986_PIN(38, "SPI2_WP"), - MT7986_PIN(39, "UART0_RXD"), - MT7986_PIN(40, "UART0_TXD"), - MT7986_NOT_BALLOUT_PIN(41), - MT7986_NOT_BALLOUT_PIN(42), - MT7986_NOT_BALLOUT_PIN(43), - MT7986_NOT_BALLOUT_PIN(44), - MT7986_NOT_BALLOUT_PIN(45), - MT7986_NOT_BALLOUT_PIN(46), - MT7986_NOT_BALLOUT_PIN(47), - MT7986_NOT_BALLOUT_PIN(48), - MT7986_NOT_BALLOUT_PIN(49), - MT7986_NOT_BALLOUT_PIN(50), - MT7986_NOT_BALLOUT_PIN(51), - MT7986_NOT_BALLOUT_PIN(52), - MT7986_NOT_BALLOUT_PIN(53), - MT7986_NOT_BALLOUT_PIN(54), - MT7986_NOT_BALLOUT_PIN(55), - MT7986_NOT_BALLOUT_PIN(56), - MT7986_NOT_BALLOUT_PIN(57), - MT7986_NOT_BALLOUT_PIN(58), - MT7986_NOT_BALLOUT_PIN(59), - MT7986_NOT_BALLOUT_PIN(60), - MT7986_NOT_BALLOUT_PIN(61), - MT7986_NOT_BALLOUT_PIN(62), - MT7986_NOT_BALLOUT_PIN(63), - MT7986_NOT_BALLOUT_PIN(64), - MT7986_NOT_BALLOUT_PIN(65), - MT7986_PIN(66, "MT7531_INT"), - MT7986_PIN(67, "SMI_MDC"), - MT7986_PIN(68, "SMI_MDIO"), - MT7986_PIN(69, "WF0_DIG_RESETB"), - MT7986_PIN(70, "WF0_CBA_RESETB"), - MT7986_PIN(71, "WF0_XO_REQ"), - MT7986_PIN(72, "WF0_TOP_CLK"), - MT7986_PIN(73, "WF0_TOP_DATA"), - MT7986_PIN(74, "WF0_HB1"), - MT7986_PIN(75, "WF0_HB2"), - MT7986_PIN(76, "WF0_HB3"), - MT7986_PIN(77, "WF0_HB4"), - MT7986_PIN(78, "WF0_HB0"), - MT7986_PIN(79, "WF0_HB0_B"), - MT7986_PIN(80, "WF0_HB5"), - MT7986_PIN(81, "WF0_HB6"), - MT7986_PIN(82, "WF0_HB7"), - MT7986_PIN(83, "WF0_HB8"), - MT7986_PIN(84, "WF0_HB9"), - MT7986_PIN(85, "WF0_HB10"), - MT7986_PIN(86, "WF1_DIG_RESETB"), - MT7986_PIN(87, "WF1_CBA_RESETB"), - MT7986_PIN(88, "WF1_XO_REQ"), - MT7986_PIN(89, "WF1_TOP_CLK"), - MT7986_PIN(90, "WF1_TOP_DATA"), - MT7986_PIN(91, "WF1_HB1"), - MT7986_PIN(92, "WF1_HB2"), - MT7986_PIN(93, "WF1_HB3"), - MT7986_PIN(94, "WF1_HB4"), - MT7986_PIN(95, "WF1_HB0"), - MT7986_PIN(96, "WF1_HB0_B"), - MT7986_PIN(97, "WF1_HB5"), - MT7986_PIN(98, "WF1_HB6"), - MT7986_PIN(99, "WF1_HB7"), - MT7986_PIN(100, "WF1_HB8"), -}; - -/* List all groups consisting of these pins dedicated to the enablement of - * certain hardware block and the corresponding mode for all of the pins. - * The hardware probably has multiple combinations of these pinouts. - */ - -static int mt7986_watchdog_pins[] = { 0, }; -static int mt7986_watchdog_funcs[] = { 1, }; - -static int mt7986_wifi_led_pins[] = { 1, 2, }; -static int mt7986_wifi_led_funcs[] = { 1, 1, }; - -static int mt7986_i2c_pins[] = { 3, 4, }; -static int mt7986_i2c_funcs[] = { 1, 1, }; - -static int mt7986_uart1_0_pins[] = { 7, 8, 9, 10, }; -static int mt7986_uart1_0_funcs[] = { 3, 3, 3, 3, }; - -static int mt7986_spi1_0_pins[] = { 11, 12, 13, 14, }; -static int mt7986_spi1_0_funcs[] = { 3, 3, 3, 3, }; - -static int mt7986_pwm1_1_pins[] = { 20, }; -static int mt7986_pwm1_1_funcs[] = { 2, }; - -static int mt7986_pwm0_pins[] = { 21, }; -static int mt7986_pwm0_funcs[] = { 1, }; - -static int mt7986_pwm1_0_pins[] = { 22, }; -static int mt7986_pwm1_0_funcs[] = { 1, }; - -static int mt7986_emmc_45_pins[] = { - 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, }; -static int mt7986_emmc_45_funcs[] = { 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, }; - -static int mt7986_snfi_pins[] = { 23, 24, 25, 26, 27, 28, }; -static int mt7986_snfi_funcs[] = { 1, 1, 1, 1, 1, 1, }; - -static int mt7986_spi1_1_pins[] = { 23, 24, 25, 26, }; -static int mt7986_spi1_1_funcs[] = { 3, 3, 3, 3, }; - -static int mt7986_uart1_1_pins[] = { 23, 24, 25, 26, }; -static int mt7986_uart1_1_funcs[] = { 4, 4, 4, 4, }; - -static int mt7986_spi1_2_pins[] = { 29, 30, 31, 32, }; -static int mt7986_spi1_2_funcs[] = { 1, 1, 1, 1, }; - -static int mt7986_uart1_2_rx_tx_pins[] = { 29, 30, }; -static int mt7986_uart1_2_rx_tx_funcs[] = { 3, 3, }; - -static int mt7986_uart1_2_cts_rts_pins[] = { 31, 32, }; -static int mt7986_uart1_2_cts_rts_funcs[] = { 3, 3, }; - -static int mt7986_uart2_0_rx_tx_pins[] = { 29, 30, }; -static int mt7986_uart2_0_rx_tx_funcs[] = { 4, 4, }; - -static int mt7986_uart2_0_cts_rts_pins[] = { 31, 32, }; -static int mt7986_uart2_0_cts_rts_funcs[] = { 4, 4, }; - -static int mt7986_spi0_pins[] = { 33, 34, 35, 36, }; -static int mt7986_spi0_funcs[] = { 1, 1, 1, 1, }; - -static int mt7986_spi0_wp_hold_pins[] = { 37, 38, }; -static int mt7986_spi0_wp_hold_funcs[] = { 1, 1, }; - -static int mt7986_uart2_1_pins[] = { 33, 34, 35, 36, }; -static int mt7986_uart2_1_funcs[] = { 3, 3, 3, 3, }; - -static int mt7986_uart1_3_rx_tx_pins[] = { 35, 36, }; -static int mt7986_uart1_3_rx_tx_funcs[] = { 2, 2, }; - -static int mt7986_uart1_3_cts_rts_pins[] = { 37, 38, }; -static int mt7986_uart1_3_cts_rts_funcs[] = { 2, 2, }; - -static int mt7986_spi1_3_pins[] = { 33, 34, 35, 36, }; -static int mt7986_spi1_3_funcs[] = { 4, 4, 4, 4, }; - -static int mt7986_uart0_pins[] = { 39, 40, }; -static int mt7986_uart0_funcs[] = { 1, 1, }; - -static int mt7986_pcie_reset_pins[] = { 41, }; -static int mt7986_pcie_reset_funcs[] = { 1, }; - -static int mt7986_uart1_pins[] = { 42, 43, 44, 45, }; -static int mt7986_uart1_funcs[] = { 1, 1, 1, 1, }; - -static int mt7986_uart1_rx_tx_pins[] = { 42, 43, }; -static int mt7986_uart1_rx_tx_funcs[] = { 1, 1, }; - -static int mt7986_uart1_cts_rts_pins[] = { 44, 45, }; -static int mt7986_uart1_cts_rts_funcs[] = { 1, 1, }; - -static int mt7986_uart2_pins[] = { 46, 47, 48, 49, }; -static int mt7986_uart2_funcs[] = { 1, 1, 1, 1, }; - -static int mt7986_emmc_51_pins[] = { - 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, }; -static int mt7986_emmc_51_funcs[] = { 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, }; - -static int mt7986_pcm_pins[] = { 62, 63, 64, 65, }; -static int mt7986_pcm_funcs[] = { 1, 1, 1, 1, }; - -static int mt7986_i2s_pins[] = { 62, 63, 64, 65, }; -static int mt7986_i2s_funcs[] = { 1, 1, 1, 1, }; - -static int mt7986_switch_int_pins[] = { 66, }; -static int mt7986_switch_int_funcs[] = { 1, }; - -static int mt7986_mdc_mdio_pins[] = { 67, 68, }; -static int mt7986_mdc_mdio_funcs[] = { 1, 1, }; - -static int mt7986_wf_2g_pins[] = {74, 75, 76, 77, 78, 79, 80, 81, 82, 83, }; -static int mt7986_wf_2g_funcs[] = {1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, }; - -static int mt7986_wf_5g_pins[] = {91, 92, 93, 94, 95, 96, 97, 98, 99, 100, }; -static int mt7986_wf_5g_funcs[] = {1, 1, 1, 1, 1, 1, 1, 1, 1, 1, }; - -static int mt7986_wf_dbdc_pins[] = { - 74, 75, 76, 77, 78, 79, 80, 81, 82, 83, 84, 85, }; -static int mt7986_wf_dbdc_funcs[] = { - 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, }; - -static int mt7986_pcie_clk_pins[] = { 9, }; -static int mt7986_pcie_clk_funcs[] = { 1, }; - -static int mt7986_pcie_wake_pins[] = { 10, }; -static int mt7986_pcie_wake_funcs[] = { 1, }; - -static const struct group_desc mt7986_groups[] = { - PINCTRL_PIN_GROUP("watchdog", mt7986_watchdog), - PINCTRL_PIN_GROUP("wifi_led", mt7986_wifi_led), - PINCTRL_PIN_GROUP("i2c", mt7986_i2c), - PINCTRL_PIN_GROUP("uart1_0", mt7986_uart1_0), - PINCTRL_PIN_GROUP("uart1_rx_tx", mt7986_uart1_rx_tx), - PINCTRL_PIN_GROUP("uart1_cts_rts", mt7986_uart1_cts_rts), - PINCTRL_PIN_GROUP("pcie_clk", mt7986_pcie_clk), - PINCTRL_PIN_GROUP("pcie_wake", mt7986_pcie_wake), - PINCTRL_PIN_GROUP("spi1_0", mt7986_spi1_0), - PINCTRL_PIN_GROUP("pwm1_1", mt7986_pwm1_1), - PINCTRL_PIN_GROUP("pwm0", mt7986_pwm0), - PINCTRL_PIN_GROUP("pwm1_0", mt7986_pwm1_0), - PINCTRL_PIN_GROUP("emmc_45", mt7986_emmc_45), - PINCTRL_PIN_GROUP("snfi", mt7986_snfi), - PINCTRL_PIN_GROUP("spi1_1", mt7986_spi1_1), - PINCTRL_PIN_GROUP("uart1_1", mt7986_uart1_1), - PINCTRL_PIN_GROUP("spi1_2", mt7986_spi1_2), - PINCTRL_PIN_GROUP("uart1_2_rx_tx", mt7986_uart1_2_rx_tx), - PINCTRL_PIN_GROUP("uart1_2_cts_rts", mt7986_uart1_2_cts_rts), - PINCTRL_PIN_GROUP("uart2_0_rx_tx", mt7986_uart2_0_rx_tx), - PINCTRL_PIN_GROUP("uart2_0_cts_rts", mt7986_uart2_0_cts_rts), - PINCTRL_PIN_GROUP("spi0", mt7986_spi0), - PINCTRL_PIN_GROUP("spi0_wp_hold", mt7986_spi0_wp_hold), - PINCTRL_PIN_GROUP("uart2_1", mt7986_uart2_1), - PINCTRL_PIN_GROUP("uart1_3_rx_tx", mt7986_uart1_3_rx_tx), - PINCTRL_PIN_GROUP("uart1_3_cts_rts", mt7986_uart1_3_cts_rts), - PINCTRL_PIN_GROUP("spi1_3", mt7986_spi1_3), - PINCTRL_PIN_GROUP("uart0", mt7986_uart0), - PINCTRL_PIN_GROUP("switch_int", mt7986_switch_int), - PINCTRL_PIN_GROUP("mdc_mdio", mt7986_mdc_mdio), - PINCTRL_PIN_GROUP("pcie_pereset", mt7986_pcie_reset), - PINCTRL_PIN_GROUP("uart1", mt7986_uart1), - PINCTRL_PIN_GROUP("uart2", mt7986_uart2), - PINCTRL_PIN_GROUP("emmc_51", mt7986_emmc_51), - PINCTRL_PIN_GROUP("pcm", mt7986_pcm), - PINCTRL_PIN_GROUP("i2s", mt7986_i2s), - PINCTRL_PIN_GROUP("wf_2g", mt7986_wf_2g), - PINCTRL_PIN_GROUP("wf_5g", mt7986_wf_5g), - PINCTRL_PIN_GROUP("wf_dbdc", mt7986_wf_dbdc), -}; - -/* Joint those groups owning the same capability in user point of view which - * allows that people tend to use through the device tree. - */ - -static const char *mt7986_audio_groups[] = { "pcm", "i2s" }; -static const char *mt7986_emmc_groups[] = { - "emmc_45", "emmc_51", }; -static const char *mt7986_ethernet_groups[] = { - "switch_int", "mdc_mdio", }; -static const char *mt7986_i2c_groups[] = { "i2c", }; -static const char *mt7986_led_groups[] = { "wifi_led", }; -static const char *mt7986_flash_groups[] = { "snfi", }; -static const char *mt7986_pcie_groups[] = { - "pcie_clk", "pcie_wake", "pcie_pereset" }; -static const char *mt7986_pwm_groups[] = { "pwm0", "pwm1_0", "pwm1_1", }; -static const char *mt7986_spi_groups[] = { - "spi0", "spi0_wp_hold", "spi1_0", "spi1_1", "spi1_2", "spi1_3", }; -static const char *mt7986_uart_groups[] = { - "uart1_0", "uart1_1", "uart1_rx_tx", "uart1_cts_rts", - "uart1_2_rx_tx", "uart1_2_cts_rts", - "uart1_3_rx_tx", "uart1_3_cts_rts", "uart2_0_rx_tx", "uart2_0_cts_rts", - "uart2_0", "uart2_1", "uart0", "uart1", "uart2", -}; -static const char *mt7986_wdt_groups[] = { "watchdog", }; -static const char *mt7986_wf_groups[] = { "wf_2g", "wf_5g", "wf_dbdc", }; - -static const struct function_desc mt7986_functions[] = { - {"audio", mt7986_audio_groups, ARRAY_SIZE(mt7986_audio_groups)}, - {"emmc", mt7986_emmc_groups, ARRAY_SIZE(mt7986_emmc_groups)}, - {"eth", mt7986_ethernet_groups, ARRAY_SIZE(mt7986_ethernet_groups)}, - {"i2c", mt7986_i2c_groups, ARRAY_SIZE(mt7986_i2c_groups)}, - {"led", mt7986_led_groups, ARRAY_SIZE(mt7986_led_groups)}, - {"flash", mt7986_flash_groups, ARRAY_SIZE(mt7986_flash_groups)}, - {"pcie", mt7986_pcie_groups, ARRAY_SIZE(mt7986_pcie_groups)}, - {"pwm", mt7986_pwm_groups, ARRAY_SIZE(mt7986_pwm_groups)}, - {"spi", mt7986_spi_groups, ARRAY_SIZE(mt7986_spi_groups)}, - {"uart", mt7986_uart_groups, ARRAY_SIZE(mt7986_uart_groups)}, - {"watchdog", mt7986_wdt_groups, ARRAY_SIZE(mt7986_wdt_groups)}, - {"wifi", mt7986_wf_groups, ARRAY_SIZE(mt7986_wf_groups)}, -}; - -static const struct mtk_eint_hw mt7986a_eint_hw = { - .port_mask = 7, - .ports = 7, - .ap_num = ARRAY_SIZE(mt7986a_pins), - .db_cnt = 16, - .db_time = debounce_time_mt6765, -}; - -static const struct mtk_eint_hw mt7986b_eint_hw = { - .port_mask = 7, - .ports = 7, - .ap_num = ARRAY_SIZE(mt7986b_pins), - .db_cnt = 16, - .db_time = debounce_time_mt6765, -}; - -static struct mtk_pin_soc mt7986a_data = { - .reg_cal = mt7986_reg_cals, - .pins = mt7986a_pins, - .npins = ARRAY_SIZE(mt7986a_pins), - .grps = mt7986_groups, - .ngrps = ARRAY_SIZE(mt7986_groups), - .funcs = mt7986_functions, - .nfuncs = ARRAY_SIZE(mt7986_functions), - .eint_hw = &mt7986a_eint_hw, - .gpio_m = 0, - .ies_present = false, - .base_names = mt7986_pinctrl_register_base_names, - .nbase_names = ARRAY_SIZE(mt7986_pinctrl_register_base_names), - .bias_disable_set = mtk_pinconf_bias_disable_set, - .bias_disable_get = mtk_pinconf_bias_disable_get, - .bias_set = mtk_pinconf_bias_set, - .bias_get = mtk_pinconf_bias_get, - .pull_type = mt7986_pull_type, - .bias_set_combo = mtk_pinconf_bias_set_combo, - .bias_get_combo = mtk_pinconf_bias_get_combo, - .drive_set = mtk_pinconf_drive_set_rev1, - .drive_get = mtk_pinconf_drive_get_rev1, - .adv_pull_get = mtk_pinconf_adv_pull_get, - .adv_pull_set = mtk_pinconf_adv_pull_set, -}; - -static struct mtk_pin_soc mt7986b_data = { - .reg_cal = mt7986_reg_cals, - .pins = mt7986b_pins, - .npins = ARRAY_SIZE(mt7986b_pins), - .grps = mt7986_groups, - .ngrps = ARRAY_SIZE(mt7986_groups), - .funcs = mt7986_functions, - .nfuncs = ARRAY_SIZE(mt7986_functions), - .eint_hw = &mt7986b_eint_hw, - .gpio_m = 0, - .ies_present = false, - .base_names = mt7986_pinctrl_register_base_names, - .nbase_names = ARRAY_SIZE(mt7986_pinctrl_register_base_names), - .bias_disable_set = mtk_pinconf_bias_disable_set, - .bias_disable_get = mtk_pinconf_bias_disable_get, - .bias_set = mtk_pinconf_bias_set, - .bias_get = mtk_pinconf_bias_get, - .pull_type = mt7986_pull_type, - .bias_set_combo = mtk_pinconf_bias_set_combo, - .bias_get_combo = mtk_pinconf_bias_get_combo, - .drive_set = mtk_pinconf_drive_set_rev1, - .drive_get = mtk_pinconf_drive_get_rev1, - .adv_pull_get = mtk_pinconf_adv_pull_get, - .adv_pull_set = mtk_pinconf_adv_pull_set, -}; - -static const struct of_device_id mt7986a_pinctrl_of_match[] = { - {.compatible = "mediatek,mt7986a-pinctrl",}, - {} -}; - -static const struct of_device_id mt7986b_pinctrl_of_match[] = { - {.compatible = "mediatek,mt7986b-pinctrl",}, - {} -}; - -static int mt7986a_pinctrl_probe(struct platform_device *pdev) -{ - return mtk_moore_pinctrl_probe(pdev, &mt7986a_data); -} - -static int mt7986b_pinctrl_probe(struct platform_device *pdev) -{ - return mtk_moore_pinctrl_probe(pdev, &mt7986b_data); -} - -static struct platform_driver mt7986a_pinctrl_driver = { - .driver = { - .name = "mt7986a-pinctrl", - .of_match_table = mt7986a_pinctrl_of_match, - }, - .probe = mt7986a_pinctrl_probe, -}; - -static struct platform_driver mt7986b_pinctrl_driver = { - .driver = { - .name = "mt7986b-pinctrl", - .of_match_table = mt7986b_pinctrl_of_match, - }, - .probe = mt7986b_pinctrl_probe, -}; - -static int __init mt7986a_pinctrl_init(void) -{ - return platform_driver_register(&mt7986a_pinctrl_driver); -} - -static int __init mt7986b_pinctrl_init(void) -{ - return platform_driver_register(&mt7986b_pinctrl_driver); -} - -arch_initcall(mt7986a_pinctrl_init); -arch_initcall(mt7986b_pinctrl_init); diff --git a/target/linux/mediatek/files-5.15/drivers/pinctrl/mediatek/pinctrl-mt7988.c b/target/linux/mediatek/files-5.15/drivers/pinctrl/mediatek/pinctrl-mt7988.c deleted file mode 100644 index 659c83e997..0000000000 --- a/target/linux/mediatek/files-5.15/drivers/pinctrl/mediatek/pinctrl-mt7988.c +++ /dev/null @@ -1,1466 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * The MT7988 driver based on Linux generic pinctrl binding. - * - * Copyright (C) 2020 MediaTek Inc. - * Author: Sam Shih - */ - -#include "pinctrl-moore.h" - -enum MT7988_PINCTRL_REG_PAGE { - GPIO_BASE, - IOCFG_TR_BASE, - IOCFG_BR_BASE, - IOCFG_RB_BASE, - IOCFG_LB_BASE, - IOCFG_TL_BASE, -}; - -#define MT7988_PIN(_number, _name) MTK_PIN(_number, _name, 0, _number, DRV_GRP4) - -#define PIN_FIELD_BASE(_s_pin, _e_pin, _i_base, _s_addr, _x_addrs, _s_bit, \ - _x_bits) \ - PIN_FIELD_CALC(_s_pin, _e_pin, _i_base, _s_addr, _x_addrs, _s_bit, \ - _x_bits, 32, 0) - -#define PINS_FIELD_BASE(_s_pin, _e_pin, _i_base, _s_addr, _x_addrs, _s_bit, \ - _x_bits) \ - PIN_FIELD_CALC(_s_pin, _e_pin, _i_base, _s_addr, _x_addrs, _s_bit, \ - _x_bits, 32, 1) - -static const struct mtk_pin_field_calc mt7988_pin_mode_range[] = { - PIN_FIELD(0, 83, 0x300, 0x10, 0, 4), -}; - -static const struct mtk_pin_field_calc mt7988_pin_dir_range[] = { - PIN_FIELD(0, 83, 0x0, 0x10, 0, 1), -}; - -static const struct mtk_pin_field_calc mt7988_pin_di_range[] = { - PIN_FIELD(0, 83, 0x200, 0x10, 0, 1), -}; - -static const struct mtk_pin_field_calc mt7988_pin_do_range[] = { - PIN_FIELD(0, 83, 0x100, 0x10, 0, 1), -}; - -static const struct mtk_pin_field_calc mt7988_pin_ies_range[] = { - PIN_FIELD_BASE(0, 0, 5, 0x30, 0x10, 13, 1), - PIN_FIELD_BASE(1, 1, 5, 0x30, 0x10, 14, 1), - PIN_FIELD_BASE(2, 2, 5, 0x30, 0x10, 11, 1), - PIN_FIELD_BASE(3, 3, 5, 0x30, 0x10, 12, 1), - PIN_FIELD_BASE(4, 4, 5, 0x30, 0x10, 0, 1), - PIN_FIELD_BASE(5, 5, 5, 0x30, 0x10, 9, 1), - PIN_FIELD_BASE(6, 6, 5, 0x30, 0x10, 10, 1), - - PIN_FIELD_BASE(7, 7, 4, 0x30, 0x10, 8, 1), - PIN_FIELD_BASE(8, 8, 4, 0x30, 0x10, 6, 1), - PIN_FIELD_BASE(9, 9, 4, 0x30, 0x10, 5, 1), - PIN_FIELD_BASE(10, 10, 4, 0x30, 0x10, 3, 1), - - PIN_FIELD_BASE(11, 11, 1, 0x40, 0x10, 0, 1), - PIN_FIELD_BASE(12, 12, 1, 0x40, 0x10, 21, 1), - PIN_FIELD_BASE(13, 13, 1, 0x40, 0x10, 1, 1), - PIN_FIELD_BASE(14, 14, 1, 0x40, 0x10, 2, 1), - - PIN_FIELD_BASE(15, 15, 5, 0x30, 0x10, 7, 1), - PIN_FIELD_BASE(16, 16, 5, 0x30, 0x10, 8, 1), - PIN_FIELD_BASE(17, 17, 5, 0x30, 0x10, 3, 1), - PIN_FIELD_BASE(18, 18, 5, 0x30, 0x10, 4, 1), - - PIN_FIELD_BASE(19, 19, 4, 0x30, 0x10, 7, 1), - PIN_FIELD_BASE(20, 20, 4, 0x30, 0x10, 4, 1), - - PIN_FIELD_BASE(21, 21, 3, 0x50, 0x10, 17, 1), - PIN_FIELD_BASE(22, 22, 3, 0x50, 0x10, 23, 1), - PIN_FIELD_BASE(23, 23, 3, 0x50, 0x10, 20, 1), - PIN_FIELD_BASE(24, 24, 3, 0x50, 0x10, 19, 1), - PIN_FIELD_BASE(25, 25, 3, 0x50, 0x10, 21, 1), - PIN_FIELD_BASE(26, 26, 3, 0x50, 0x10, 22, 1), - PIN_FIELD_BASE(27, 27, 3, 0x50, 0x10, 18, 1), - PIN_FIELD_BASE(28, 28, 3, 0x50, 0x10, 25, 1), - PIN_FIELD_BASE(29, 29, 3, 0x50, 0x10, 26, 1), - PIN_FIELD_BASE(30, 30, 3, 0x50, 0x10, 27, 1), - PIN_FIELD_BASE(31, 31, 3, 0x50, 0x10, 24, 1), - PIN_FIELD_BASE(32, 32, 3, 0x50, 0x10, 28, 1), - PIN_FIELD_BASE(33, 33, 3, 0x60, 0x10, 0, 1), - PIN_FIELD_BASE(34, 34, 3, 0x50, 0x10, 31, 1), - PIN_FIELD_BASE(35, 35, 3, 0x50, 0x10, 29, 1), - PIN_FIELD_BASE(36, 36, 3, 0x50, 0x10, 30, 1), - PIN_FIELD_BASE(37, 37, 3, 0x60, 0x10, 1, 1), - PIN_FIELD_BASE(38, 38, 3, 0x50, 0x10, 11, 1), - PIN_FIELD_BASE(39, 39, 3, 0x50, 0x10, 10, 1), - PIN_FIELD_BASE(40, 40, 3, 0x50, 0x10, 0, 1), - PIN_FIELD_BASE(41, 41, 3, 0x50, 0x10, 1, 1), - PIN_FIELD_BASE(42, 42, 3, 0x50, 0x10, 9, 1), - PIN_FIELD_BASE(43, 43, 3, 0x50, 0x10, 8, 1), - PIN_FIELD_BASE(44, 44, 3, 0x50, 0x10, 7, 1), - PIN_FIELD_BASE(45, 45, 3, 0x50, 0x10, 6, 1), - PIN_FIELD_BASE(46, 46, 3, 0x50, 0x10, 5, 1), - PIN_FIELD_BASE(47, 47, 3, 0x50, 0x10, 4, 1), - PIN_FIELD_BASE(48, 48, 3, 0x50, 0x10, 3, 1), - PIN_FIELD_BASE(49, 49, 3, 0x50, 0x10, 2, 1), - PIN_FIELD_BASE(50, 50, 3, 0x50, 0x10, 15, 1), - PIN_FIELD_BASE(51, 51, 3, 0x50, 0x10, 12, 1), - PIN_FIELD_BASE(52, 52, 3, 0x50, 0x10, 13, 1), - PIN_FIELD_BASE(53, 53, 3, 0x50, 0x10, 14, 1), - PIN_FIELD_BASE(54, 54, 3, 0x50, 0x10, 16, 1), - - PIN_FIELD_BASE(55, 55, 1, 0x40, 0x10, 14, 1), - PIN_FIELD_BASE(56, 56, 1, 0x40, 0x10, 15, 1), - PIN_FIELD_BASE(57, 57, 1, 0x40, 0x10, 13, 1), - PIN_FIELD_BASE(58, 58, 1, 0x40, 0x10, 4, 1), - PIN_FIELD_BASE(59, 59, 1, 0x40, 0x10, 5, 1), - PIN_FIELD_BASE(60, 60, 1, 0x40, 0x10, 6, 1), - PIN_FIELD_BASE(61, 61, 1, 0x40, 0x10, 3, 1), - PIN_FIELD_BASE(62, 62, 1, 0x40, 0x10, 7, 1), - PIN_FIELD_BASE(63, 63, 1, 0x40, 0x10, 20, 1), - PIN_FIELD_BASE(64, 64, 1, 0x40, 0x10, 8, 1), - PIN_FIELD_BASE(65, 65, 1, 0x40, 0x10, 9, 1), - PIN_FIELD_BASE(66, 66, 1, 0x40, 0x10, 10, 1), - PIN_FIELD_BASE(67, 67, 1, 0x40, 0x10, 11, 1), - PIN_FIELD_BASE(68, 68, 1, 0x40, 0x10, 12, 1), - - PIN_FIELD_BASE(69, 69, 5, 0x30, 0x10, 1, 1), - PIN_FIELD_BASE(70, 70, 5, 0x30, 0x10, 2, 1), - PIN_FIELD_BASE(71, 71, 5, 0x30, 0x10, 5, 1), - PIN_FIELD_BASE(72, 72, 5, 0x30, 0x10, 6, 1), - - PIN_FIELD_BASE(73, 73, 4, 0x30, 0x10, 10, 1), - PIN_FIELD_BASE(74, 74, 4, 0x30, 0x10, 1, 1), - PIN_FIELD_BASE(75, 75, 4, 0x30, 0x10, 11, 1), - PIN_FIELD_BASE(76, 76, 4, 0x30, 0x10, 9, 1), - PIN_FIELD_BASE(77, 77, 4, 0x30, 0x10, 2, 1), - PIN_FIELD_BASE(78, 78, 4, 0x30, 0x10, 0, 1), - PIN_FIELD_BASE(79, 79, 4, 0x30, 0x10, 12, 1), - - PIN_FIELD_BASE(80, 80, 1, 0x40, 0x10, 18, 1), - PIN_FIELD_BASE(81, 81, 1, 0x40, 0x10, 19, 1), - PIN_FIELD_BASE(82, 82, 1, 0x40, 0x10, 16, 1), - PIN_FIELD_BASE(83, 83, 1, 0x40, 0x10, 17, 1), -}; - -static const struct mtk_pin_field_calc mt7988_pin_smt_range[] = { - PIN_FIELD_BASE(0, 0, 5, 0xc0, 0x10, 13, 1), - PIN_FIELD_BASE(1, 1, 5, 0xc0, 0x10, 14, 1), - PIN_FIELD_BASE(2, 2, 5, 0xc0, 0x10, 11, 1), - PIN_FIELD_BASE(3, 3, 5, 0xc0, 0x10, 12, 1), - PIN_FIELD_BASE(4, 4, 5, 0xc0, 0x10, 0, 1), - PIN_FIELD_BASE(5, 5, 5, 0xc0, 0x10, 9, 1), - PIN_FIELD_BASE(6, 6, 5, 0xc0, 0x10, 10, 1), - - PIN_FIELD_BASE(7, 7, 4, 0xb0, 0x10, 8, 1), - PIN_FIELD_BASE(8, 8, 4, 0xb0, 0x10, 6, 1), - PIN_FIELD_BASE(9, 9, 4, 0xb0, 0x10, 5, 1), - PIN_FIELD_BASE(10, 10, 4, 0xb0, 0x10, 3, 1), - - PIN_FIELD_BASE(11, 11, 1, 0xe0, 0x10, 0, 1), - PIN_FIELD_BASE(12, 12, 1, 0xe0, 0x10, 21, 1), - PIN_FIELD_BASE(13, 13, 1, 0xe0, 0x10, 1, 1), - PIN_FIELD_BASE(14, 14, 1, 0xe0, 0x10, 2, 1), - - PIN_FIELD_BASE(15, 15, 5, 0xc0, 0x10, 7, 1), - PIN_FIELD_BASE(16, 16, 5, 0xc0, 0x10, 8, 1), - PIN_FIELD_BASE(17, 17, 5, 0xc0, 0x10, 3, 1), - PIN_FIELD_BASE(18, 18, 5, 0xc0, 0x10, 4, 1), - - PIN_FIELD_BASE(19, 19, 4, 0xb0, 0x10, 7, 1), - PIN_FIELD_BASE(20, 20, 4, 0xb0, 0x10, 4, 1), - - PIN_FIELD_BASE(21, 21, 3, 0x140, 0x10, 17, 1), - PIN_FIELD_BASE(22, 22, 3, 0x140, 0x10, 23, 1), - PIN_FIELD_BASE(23, 23, 3, 0x140, 0x10, 20, 1), - PIN_FIELD_BASE(24, 24, 3, 0x140, 0x10, 19, 1), - PIN_FIELD_BASE(25, 25, 3, 0x140, 0x10, 21, 1), - PIN_FIELD_BASE(26, 26, 3, 0x140, 0x10, 22, 1), - PIN_FIELD_BASE(27, 27, 3, 0x140, 0x10, 18, 1), - PIN_FIELD_BASE(28, 28, 3, 0x140, 0x10, 25, 1), - PIN_FIELD_BASE(29, 29, 3, 0x140, 0x10, 26, 1), - PIN_FIELD_BASE(30, 30, 3, 0x140, 0x10, 27, 1), - PIN_FIELD_BASE(31, 31, 3, 0x140, 0x10, 24, 1), - PIN_FIELD_BASE(32, 32, 3, 0x140, 0x10, 28, 1), - PIN_FIELD_BASE(33, 33, 3, 0x150, 0x10, 0, 1), - PIN_FIELD_BASE(34, 34, 3, 0x140, 0x10, 31, 1), - PIN_FIELD_BASE(35, 35, 3, 0x140, 0x10, 29, 1), - PIN_FIELD_BASE(36, 36, 3, 0x140, 0x10, 30, 1), - PIN_FIELD_BASE(37, 37, 3, 0x150, 0x10, 1, 1), - PIN_FIELD_BASE(38, 38, 3, 0x140, 0x10, 11, 1), - PIN_FIELD_BASE(39, 39, 3, 0x140, 0x10, 10, 1), - PIN_FIELD_BASE(40, 40, 3, 0x140, 0x10, 0, 1), - PIN_FIELD_BASE(41, 41, 3, 0x140, 0x10, 1, 1), - PIN_FIELD_BASE(42, 42, 3, 0x140, 0x10, 9, 1), - PIN_FIELD_BASE(43, 43, 3, 0x140, 0x10, 8, 1), - PIN_FIELD_BASE(44, 44, 3, 0x140, 0x10, 7, 1), - PIN_FIELD_BASE(45, 45, 3, 0x140, 0x10, 6, 1), - PIN_FIELD_BASE(46, 46, 3, 0x140, 0x10, 5, 1), - PIN_FIELD_BASE(47, 47, 3, 0x140, 0x10, 4, 1), - PIN_FIELD_BASE(48, 48, 3, 0x140, 0x10, 3, 1), - PIN_FIELD_BASE(49, 49, 3, 0x140, 0x10, 2, 1), - PIN_FIELD_BASE(50, 50, 3, 0x140, 0x10, 15, 1), - PIN_FIELD_BASE(51, 51, 3, 0x140, 0x10, 12, 1), - PIN_FIELD_BASE(52, 52, 3, 0x140, 0x10, 13, 1), - PIN_FIELD_BASE(53, 53, 3, 0x140, 0x10, 14, 1), - PIN_FIELD_BASE(54, 54, 3, 0x140, 0x10, 16, 1), - - PIN_FIELD_BASE(55, 55, 1, 0xe0, 0x10, 14, 1), - PIN_FIELD_BASE(56, 56, 1, 0xe0, 0x10, 15, 1), - PIN_FIELD_BASE(57, 57, 1, 0xe0, 0x10, 13, 1), - PIN_FIELD_BASE(58, 58, 1, 0xe0, 0x10, 4, 1), - PIN_FIELD_BASE(59, 59, 1, 0xe0, 0x10, 5, 1), - PIN_FIELD_BASE(60, 60, 1, 0xe0, 0x10, 6, 1), - PIN_FIELD_BASE(61, 61, 1, 0xe0, 0x10, 3, 1), - PIN_FIELD_BASE(62, 62, 1, 0xe0, 0x10, 7, 1), - PIN_FIELD_BASE(63, 63, 1, 0xe0, 0x10, 20, 1), - PIN_FIELD_BASE(64, 64, 1, 0xe0, 0x10, 8, 1), - PIN_FIELD_BASE(65, 65, 1, 0xe0, 0x10, 9, 1), - PIN_FIELD_BASE(66, 66, 1, 0xe0, 0x10, 10, 1), - PIN_FIELD_BASE(67, 67, 1, 0xe0, 0x10, 11, 1), - PIN_FIELD_BASE(68, 68, 1, 0xe0, 0x10, 12, 1), - - PIN_FIELD_BASE(69, 69, 5, 0xc0, 0x10, 1, 1), - PIN_FIELD_BASE(70, 70, 5, 0xc0, 0x10, 2, 1), - PIN_FIELD_BASE(71, 71, 5, 0xc0, 0x10, 5, 1), - PIN_FIELD_BASE(72, 72, 5, 0xc0, 0x10, 6, 1), - - PIN_FIELD_BASE(73, 73, 4, 0xb0, 0x10, 10, 1), - PIN_FIELD_BASE(74, 74, 4, 0xb0, 0x10, 1, 1), - PIN_FIELD_BASE(75, 75, 4, 0xb0, 0x10, 11, 1), - PIN_FIELD_BASE(76, 76, 4, 0xb0, 0x10, 9, 1), - PIN_FIELD_BASE(77, 77, 4, 0xb0, 0x10, 2, 1), - PIN_FIELD_BASE(78, 78, 4, 0xb0, 0x10, 0, 1), - PIN_FIELD_BASE(79, 79, 4, 0xb0, 0x10, 12, 1), - - PIN_FIELD_BASE(80, 80, 1, 0xe0, 0x10, 18, 1), - PIN_FIELD_BASE(81, 81, 1, 0xe0, 0x10, 19, 1), - PIN_FIELD_BASE(82, 82, 1, 0xe0, 0x10, 16, 1), - PIN_FIELD_BASE(83, 83, 1, 0xe0, 0x10, 17, 1), -}; - -static const struct mtk_pin_field_calc mt7988_pin_pu_range[] = { - PIN_FIELD_BASE(7, 7, 4, 0x60, 0x10, 5, 1), - PIN_FIELD_BASE(8, 8, 4, 0x60, 0x10, 4, 1), - PIN_FIELD_BASE(9, 9, 4, 0x60, 0x10, 3, 1), - PIN_FIELD_BASE(10, 10, 4, 0x60, 0x10, 2, 1), - - PIN_FIELD_BASE(13, 13, 1, 0x70, 0x10, 0, 1), - PIN_FIELD_BASE(14, 14, 1, 0x70, 0x10, 1, 1), - PIN_FIELD_BASE(63, 63, 1, 0x70, 0x10, 2, 1), - - PIN_FIELD_BASE(75, 75, 4, 0x60, 0x10, 7, 1), - PIN_FIELD_BASE(76, 76, 4, 0x60, 0x10, 6, 1), - PIN_FIELD_BASE(77, 77, 4, 0x60, 0x10, 1, 1), - PIN_FIELD_BASE(78, 78, 4, 0x60, 0x10, 0, 1), - PIN_FIELD_BASE(79, 79, 4, 0x60, 0x10, 8, 1), -}; - -static const struct mtk_pin_field_calc mt7988_pin_pd_range[] = { - PIN_FIELD_BASE(7, 7, 4, 0x40, 0x10, 5, 1), - PIN_FIELD_BASE(8, 8, 4, 0x40, 0x10, 4, 1), - PIN_FIELD_BASE(9, 9, 4, 0x40, 0x10, 3, 1), - PIN_FIELD_BASE(10, 10, 4, 0x40, 0x10, 2, 1), - - PIN_FIELD_BASE(13, 13, 1, 0x50, 0x10, 0, 1), - PIN_FIELD_BASE(14, 14, 1, 0x50, 0x10, 1, 1), - - PIN_FIELD_BASE(15, 15, 5, 0x40, 0x10, 4, 1), - PIN_FIELD_BASE(16, 16, 5, 0x40, 0x10, 5, 1), - PIN_FIELD_BASE(17, 17, 5, 0x40, 0x10, 0, 1), - PIN_FIELD_BASE(18, 18, 5, 0x40, 0x10, 1, 1), - - PIN_FIELD_BASE(63, 63, 1, 0x50, 0x10, 2, 1), - PIN_FIELD_BASE(71, 71, 5, 0x40, 0x10, 2, 1), - PIN_FIELD_BASE(72, 72, 5, 0x40, 0x10, 3, 1), - - PIN_FIELD_BASE(75, 75, 4, 0x40, 0x10, 7, 1), - PIN_FIELD_BASE(76, 76, 4, 0x40, 0x10, 6, 1), - PIN_FIELD_BASE(77, 77, 4, 0x40, 0x10, 1, 1), - PIN_FIELD_BASE(78, 78, 4, 0x40, 0x10, 0, 1), - PIN_FIELD_BASE(79, 79, 4, 0x40, 0x10, 8, 1), -}; - -static const struct mtk_pin_field_calc mt7988_pin_drv_range[] = { - PIN_FIELD_BASE(0, 0, 5, 0x00, 0x10, 21, 3), - PIN_FIELD_BASE(1, 1, 5, 0x00, 0x10, 24, 3), - PIN_FIELD_BASE(2, 2, 5, 0x00, 0x10, 15, 3), - PIN_FIELD_BASE(3, 3, 5, 0x00, 0x10, 18, 3), - PIN_FIELD_BASE(4, 4, 5, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(5, 5, 5, 0x00, 0x10, 9, 3), - PIN_FIELD_BASE(6, 6, 5, 0x00, 0x10, 12, 3), - - PIN_FIELD_BASE(7, 7, 4, 0x00, 0x10, 24, 3), - PIN_FIELD_BASE(8, 8, 4, 0x00, 0x10, 28, 3), - PIN_FIELD_BASE(9, 9, 4, 0x00, 0x10, 15, 3), - PIN_FIELD_BASE(10, 10, 4, 0x00, 0x10, 9, 3), - - PIN_FIELD_BASE(11, 11, 1, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(12, 12, 1, 0x20, 0x10, 3, 3), - PIN_FIELD_BASE(13, 13, 1, 0x00, 0x10, 3, 3), - PIN_FIELD_BASE(14, 14, 1, 0x00, 0x10, 6, 3), - - PIN_FIELD_BASE(19, 19, 4, 0x00, 0x10, 21, 3), - PIN_FIELD_BASE(20, 20, 4, 0x00, 0x10, 12, 3), - - PIN_FIELD_BASE(21, 21, 3, 0x10, 0x10, 21, 3), - PIN_FIELD_BASE(22, 22, 3, 0x20, 0x10, 9, 3), - PIN_FIELD_BASE(23, 23, 3, 0x20, 0x10, 0, 3), - PIN_FIELD_BASE(24, 24, 3, 0x10, 0x10, 27, 3), - PIN_FIELD_BASE(25, 25, 3, 0x20, 0x10, 3, 3), - PIN_FIELD_BASE(26, 26, 3, 0x20, 0x10, 6, 3), - PIN_FIELD_BASE(27, 27, 3, 0x10, 0x10, 24, 3), - PIN_FIELD_BASE(28, 28, 3, 0x20, 0x10, 15, 3), - PIN_FIELD_BASE(29, 29, 3, 0x20, 0x10, 18, 3), - PIN_FIELD_BASE(30, 30, 3, 0x20, 0x10, 21, 3), - PIN_FIELD_BASE(31, 31, 3, 0x20, 0x10, 12, 3), - PIN_FIELD_BASE(32, 32, 3, 0x20, 0x10, 24, 3), - PIN_FIELD_BASE(33, 33, 3, 0x30, 0x10, 6, 3), - PIN_FIELD_BASE(34, 34, 3, 0x30, 0x10, 3, 3), - PIN_FIELD_BASE(35, 35, 3, 0x20, 0x10, 27, 3), - PIN_FIELD_BASE(36, 36, 3, 0x30, 0x10, 0, 3), - PIN_FIELD_BASE(37, 37, 3, 0x30, 0x10, 9, 3), - PIN_FIELD_BASE(38, 38, 3, 0x10, 0x10, 3, 3), - PIN_FIELD_BASE(39, 39, 3, 0x10, 0x10, 0, 3), - PIN_FIELD_BASE(40, 40, 3, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(41, 41, 3, 0x00, 0x10, 3, 3), - PIN_FIELD_BASE(42, 42, 3, 0x00, 0x10, 27, 3), - PIN_FIELD_BASE(43, 43, 3, 0x00, 0x10, 24, 3), - PIN_FIELD_BASE(44, 44, 3, 0x00, 0x10, 21, 3), - PIN_FIELD_BASE(45, 45, 3, 0x00, 0x10, 18, 3), - PIN_FIELD_BASE(46, 46, 3, 0x00, 0x10, 15, 3), - PIN_FIELD_BASE(47, 47, 3, 0x00, 0x10, 12, 3), - PIN_FIELD_BASE(48, 48, 3, 0x00, 0x10, 9, 3), - PIN_FIELD_BASE(49, 49, 3, 0x00, 0x10, 6, 3), - PIN_FIELD_BASE(50, 50, 3, 0x10, 0x10, 15, 3), - PIN_FIELD_BASE(51, 51, 3, 0x10, 0x10, 6, 3), - PIN_FIELD_BASE(52, 52, 3, 0x10, 0x10, 9, 3), - PIN_FIELD_BASE(53, 53, 3, 0x10, 0x10, 12, 3), - PIN_FIELD_BASE(54, 54, 3, 0x10, 0x10, 18, 3), - - PIN_FIELD_BASE(55, 55, 1, 0x10, 0x10, 12, 3), - PIN_FIELD_BASE(56, 56, 1, 0x10, 0x10, 15, 3), - PIN_FIELD_BASE(57, 57, 1, 0x10, 0x10, 9, 3), - PIN_FIELD_BASE(58, 58, 1, 0x00, 0x10, 12, 3), - PIN_FIELD_BASE(59, 59, 1, 0x00, 0x10, 15, 3), - PIN_FIELD_BASE(60, 60, 1, 0x00, 0x10, 18, 3), - PIN_FIELD_BASE(61, 61, 1, 0x00, 0x10, 9, 3), - PIN_FIELD_BASE(62, 62, 1, 0x00, 0x10, 21, 3), - PIN_FIELD_BASE(63, 63, 1, 0x20, 0x10, 0, 3), - PIN_FIELD_BASE(64, 64, 1, 0x00, 0x10, 24, 3), - PIN_FIELD_BASE(65, 65, 1, 0x00, 0x10, 27, 3), - PIN_FIELD_BASE(66, 66, 1, 0x10, 0x10, 0, 3), - PIN_FIELD_BASE(67, 67, 1, 0x10, 0x10, 3, 3), - PIN_FIELD_BASE(68, 68, 1, 0x10, 0x10, 6, 3), - - PIN_FIELD_BASE(69, 69, 5, 0x00, 0x10, 3, 3), - PIN_FIELD_BASE(70, 70, 5, 0x00, 0x10, 6, 3), - - PIN_FIELD_BASE(73, 73, 4, 0x10, 0x10, 0, 3), - PIN_FIELD_BASE(74, 74, 4, 0x00, 0x10, 3, 3), - PIN_FIELD_BASE(75, 75, 4, 0x10, 0x10, 3, 3), - PIN_FIELD_BASE(76, 76, 4, 0x00, 0x10, 27, 3), - PIN_FIELD_BASE(77, 77, 4, 0x00, 0x10, 6, 3), - PIN_FIELD_BASE(78, 78, 4, 0x00, 0x10, 0, 3), - PIN_FIELD_BASE(79, 79, 4, 0x10, 0x10, 6, 3), - - PIN_FIELD_BASE(80, 80, 1, 0x10, 0x10, 24, 3), - PIN_FIELD_BASE(81, 81, 1, 0x10, 0x10, 27, 3), - PIN_FIELD_BASE(82, 82, 1, 0x10, 0x10, 18, 3), - PIN_FIELD_BASE(83, 83, 1, 0x10, 0x10, 21, 3), -}; - -static const struct mtk_pin_field_calc mt7988_pin_pupd_range[] = { - PIN_FIELD_BASE(0, 0, 5, 0x50, 0x10, 7, 1), - PIN_FIELD_BASE(1, 1, 5, 0x50, 0x10, 8, 1), - PIN_FIELD_BASE(2, 2, 5, 0x50, 0x10, 5, 1), - PIN_FIELD_BASE(3, 3, 5, 0x50, 0x10, 6, 1), - PIN_FIELD_BASE(4, 4, 5, 0x50, 0x10, 0, 1), - PIN_FIELD_BASE(5, 5, 5, 0x50, 0x10, 3, 1), - PIN_FIELD_BASE(6, 6, 5, 0x50, 0x10, 4, 1), - - PIN_FIELD_BASE(11, 11, 1, 0x60, 0x10, 0, 1), - PIN_FIELD_BASE(12, 12, 1, 0x60, 0x10, 18, 1), - - PIN_FIELD_BASE(19, 19, 4, 0x50, 0x10, 2, 1), - PIN_FIELD_BASE(20, 20, 4, 0x50, 0x10, 1, 1), - - PIN_FIELD_BASE(21, 21, 3, 0x70, 0x10, 17, 1), - PIN_FIELD_BASE(22, 22, 3, 0x70, 0x10, 23, 1), - PIN_FIELD_BASE(23, 23, 3, 0x70, 0x10, 20, 1), - PIN_FIELD_BASE(24, 24, 3, 0x70, 0x10, 19, 1), - PIN_FIELD_BASE(25, 25, 3, 0x70, 0x10, 21, 1), - PIN_FIELD_BASE(26, 26, 3, 0x70, 0x10, 22, 1), - PIN_FIELD_BASE(27, 27, 3, 0x70, 0x10, 18, 1), - PIN_FIELD_BASE(28, 28, 3, 0x70, 0x10, 25, 1), - PIN_FIELD_BASE(29, 29, 3, 0x70, 0x10, 26, 1), - PIN_FIELD_BASE(30, 30, 3, 0x70, 0x10, 27, 1), - PIN_FIELD_BASE(31, 31, 3, 0x70, 0x10, 24, 1), - PIN_FIELD_BASE(32, 32, 3, 0x70, 0x10, 28, 1), - PIN_FIELD_BASE(33, 33, 3, 0x80, 0x10, 0, 1), - PIN_FIELD_BASE(34, 34, 3, 0x70, 0x10, 31, 1), - PIN_FIELD_BASE(35, 35, 3, 0x70, 0x10, 29, 1), - PIN_FIELD_BASE(36, 36, 3, 0x70, 0x10, 30, 1), - PIN_FIELD_BASE(37, 37, 3, 0x80, 0x10, 1, 1), - PIN_FIELD_BASE(38, 38, 3, 0x70, 0x10, 11, 1), - PIN_FIELD_BASE(39, 39, 3, 0x70, 0x10, 10, 1), - PIN_FIELD_BASE(40, 40, 3, 0x70, 0x10, 0, 1), - PIN_FIELD_BASE(41, 41, 3, 0x70, 0x10, 1, 1), - PIN_FIELD_BASE(42, 42, 3, 0x70, 0x10, 9, 1), - PIN_FIELD_BASE(43, 43, 3, 0x70, 0x10, 8, 1), - PIN_FIELD_BASE(44, 44, 3, 0x70, 0x10, 7, 1), - PIN_FIELD_BASE(45, 45, 3, 0x70, 0x10, 6, 1), - PIN_FIELD_BASE(46, 46, 3, 0x70, 0x10, 5, 1), - PIN_FIELD_BASE(47, 47, 3, 0x70, 0x10, 4, 1), - PIN_FIELD_BASE(48, 48, 3, 0x70, 0x10, 3, 1), - PIN_FIELD_BASE(49, 49, 3, 0x70, 0x10, 2, 1), - PIN_FIELD_BASE(50, 50, 3, 0x70, 0x10, 15, 1), - PIN_FIELD_BASE(51, 51, 3, 0x70, 0x10, 12, 1), - PIN_FIELD_BASE(52, 52, 3, 0x70, 0x10, 13, 1), - PIN_FIELD_BASE(53, 53, 3, 0x70, 0x10, 14, 1), - PIN_FIELD_BASE(54, 54, 3, 0x70, 0x10, 16, 1), - - PIN_FIELD_BASE(55, 55, 1, 0x60, 0x10, 12, 1), - PIN_FIELD_BASE(56, 56, 1, 0x60, 0x10, 13, 1), - PIN_FIELD_BASE(57, 57, 1, 0x60, 0x10, 11, 1), - PIN_FIELD_BASE(58, 58, 1, 0x60, 0x10, 2, 1), - PIN_FIELD_BASE(59, 59, 1, 0x60, 0x10, 3, 1), - PIN_FIELD_BASE(60, 60, 1, 0x60, 0x10, 4, 1), - PIN_FIELD_BASE(61, 61, 1, 0x60, 0x10, 1, 1), - PIN_FIELD_BASE(62, 62, 1, 0x60, 0x10, 5, 1), - PIN_FIELD_BASE(64, 64, 1, 0x60, 0x10, 6, 1), - PIN_FIELD_BASE(65, 65, 1, 0x60, 0x10, 7, 1), - PIN_FIELD_BASE(66, 66, 1, 0x60, 0x10, 8, 1), - PIN_FIELD_BASE(67, 67, 1, 0x60, 0x10, 9, 1), - PIN_FIELD_BASE(68, 68, 1, 0x60, 0x10, 10, 1), - - PIN_FIELD_BASE(69, 69, 5, 0x50, 0x10, 1, 1), - PIN_FIELD_BASE(70, 70, 5, 0x50, 0x10, 2, 1), - - PIN_FIELD_BASE(73, 73, 4, 0x50, 0x10, 3, 1), - PIN_FIELD_BASE(74, 74, 4, 0x50, 0x10, 0, 1), - - PIN_FIELD_BASE(80, 80, 1, 0x60, 0x10, 16, 1), - PIN_FIELD_BASE(81, 81, 1, 0x60, 0x10, 17, 1), - PIN_FIELD_BASE(82, 82, 1, 0x60, 0x10, 14, 1), - PIN_FIELD_BASE(83, 83, 1, 0x60, 0x10, 15, 1), -}; - -static const struct mtk_pin_field_calc mt7988_pin_r0_range[] = { - PIN_FIELD_BASE(0, 0, 5, 0x60, 0x10, 7, 1), - PIN_FIELD_BASE(1, 1, 5, 0x60, 0x10, 8, 1), - PIN_FIELD_BASE(2, 2, 5, 0x60, 0x10, 5, 1), - PIN_FIELD_BASE(3, 3, 5, 0x60, 0x10, 6, 1), - PIN_FIELD_BASE(4, 4, 5, 0x60, 0x10, 0, 1), - PIN_FIELD_BASE(5, 5, 5, 0x60, 0x10, 3, 1), - PIN_FIELD_BASE(6, 6, 5, 0x60, 0x10, 4, 1), - - PIN_FIELD_BASE(11, 11, 1, 0x80, 0x10, 0, 1), - PIN_FIELD_BASE(12, 12, 1, 0x80, 0x10, 18, 1), - - PIN_FIELD_BASE(19, 19, 4, 0x70, 0x10, 2, 1), - PIN_FIELD_BASE(20, 20, 4, 0x70, 0x10, 1, 1), - - PIN_FIELD_BASE(21, 21, 3, 0x90, 0x10, 17, 1), - PIN_FIELD_BASE(22, 22, 3, 0x90, 0x10, 23, 1), - PIN_FIELD_BASE(23, 23, 3, 0x90, 0x10, 20, 1), - PIN_FIELD_BASE(24, 24, 3, 0x90, 0x10, 19, 1), - PIN_FIELD_BASE(25, 25, 3, 0x90, 0x10, 21, 1), - PIN_FIELD_BASE(26, 26, 3, 0x90, 0x10, 22, 1), - PIN_FIELD_BASE(27, 27, 3, 0x90, 0x10, 18, 1), - PIN_FIELD_BASE(28, 28, 3, 0x90, 0x10, 25, 1), - PIN_FIELD_BASE(29, 29, 3, 0x90, 0x10, 26, 1), - PIN_FIELD_BASE(30, 30, 3, 0x90, 0x10, 27, 1), - PIN_FIELD_BASE(31, 31, 3, 0x90, 0x10, 24, 1), - PIN_FIELD_BASE(32, 32, 3, 0x90, 0x10, 28, 1), - PIN_FIELD_BASE(33, 33, 3, 0xa0, 0x10, 0, 1), - PIN_FIELD_BASE(34, 34, 3, 0x90, 0x10, 31, 1), - PIN_FIELD_BASE(35, 35, 3, 0x90, 0x10, 29, 1), - PIN_FIELD_BASE(36, 36, 3, 0x90, 0x10, 30, 1), - PIN_FIELD_BASE(37, 37, 3, 0xa0, 0x10, 1, 1), - PIN_FIELD_BASE(38, 38, 3, 0x90, 0x10, 11, 1), - PIN_FIELD_BASE(39, 39, 3, 0x90, 0x10, 10, 1), - PIN_FIELD_BASE(40, 40, 3, 0x90, 0x10, 0, 1), - PIN_FIELD_BASE(41, 41, 3, 0x90, 0x10, 1, 1), - PIN_FIELD_BASE(42, 42, 3, 0x90, 0x10, 9, 1), - PIN_FIELD_BASE(43, 43, 3, 0x90, 0x10, 8, 1), - PIN_FIELD_BASE(44, 44, 3, 0x90, 0x10, 7, 1), - PIN_FIELD_BASE(45, 45, 3, 0x90, 0x10, 6, 1), - PIN_FIELD_BASE(46, 46, 3, 0x90, 0x10, 5, 1), - PIN_FIELD_BASE(47, 47, 3, 0x90, 0x10, 4, 1), - PIN_FIELD_BASE(48, 48, 3, 0x90, 0x10, 3, 1), - PIN_FIELD_BASE(49, 49, 3, 0x90, 0x10, 2, 1), - PIN_FIELD_BASE(50, 50, 3, 0x90, 0x10, 15, 1), - PIN_FIELD_BASE(51, 51, 3, 0x90, 0x10, 12, 1), - PIN_FIELD_BASE(52, 52, 3, 0x90, 0x10, 13, 1), - PIN_FIELD_BASE(53, 53, 3, 0x90, 0x10, 14, 1), - PIN_FIELD_BASE(54, 54, 3, 0x90, 0x10, 16, 1), - - PIN_FIELD_BASE(55, 55, 1, 0x80, 0x10, 12, 1), - PIN_FIELD_BASE(56, 56, 1, 0x80, 0x10, 13, 1), - PIN_FIELD_BASE(57, 57, 1, 0x80, 0x10, 11, 1), - PIN_FIELD_BASE(58, 58, 1, 0x80, 0x10, 2, 1), - PIN_FIELD_BASE(59, 59, 1, 0x80, 0x10, 3, 1), - PIN_FIELD_BASE(60, 60, 1, 0x80, 0x10, 4, 1), - PIN_FIELD_BASE(61, 61, 1, 0x80, 0x10, 1, 1), - PIN_FIELD_BASE(62, 62, 1, 0x80, 0x10, 5, 1), - PIN_FIELD_BASE(64, 64, 1, 0x80, 0x10, 6, 1), - PIN_FIELD_BASE(65, 65, 1, 0x80, 0x10, 7, 1), - PIN_FIELD_BASE(66, 66, 1, 0x80, 0x10, 8, 1), - PIN_FIELD_BASE(67, 67, 1, 0x80, 0x10, 9, 1), - PIN_FIELD_BASE(68, 68, 1, 0x80, 0x10, 10, 1), - - PIN_FIELD_BASE(69, 69, 5, 0x60, 0x10, 1, 1), - PIN_FIELD_BASE(70, 70, 5, 0x60, 0x10, 2, 1), - - PIN_FIELD_BASE(73, 73, 4, 0x70, 0x10, 3, 1), - PIN_FIELD_BASE(74, 74, 4, 0x70, 0x10, 0, 1), - - PIN_FIELD_BASE(80, 80, 1, 0x80, 0x10, 16, 1), - PIN_FIELD_BASE(81, 81, 1, 0x80, 0x10, 17, 1), - PIN_FIELD_BASE(82, 82, 1, 0x80, 0x10, 14, 1), - PIN_FIELD_BASE(83, 83, 1, 0x80, 0x10, 15, 1), -}; - -static const struct mtk_pin_field_calc mt7988_pin_r1_range[] = { - PIN_FIELD_BASE(0, 0, 5, 0x70, 0x10, 7, 1), - PIN_FIELD_BASE(1, 1, 5, 0x70, 0x10, 8, 1), - PIN_FIELD_BASE(2, 2, 5, 0x70, 0x10, 5, 1), - PIN_FIELD_BASE(3, 3, 5, 0x70, 0x10, 6, 1), - PIN_FIELD_BASE(4, 4, 5, 0x70, 0x10, 0, 1), - PIN_FIELD_BASE(5, 5, 5, 0x70, 0x10, 3, 1), - PIN_FIELD_BASE(6, 6, 5, 0x70, 0x10, 4, 1), - - PIN_FIELD_BASE(11, 11, 1, 0x90, 0x10, 0, 1), - PIN_FIELD_BASE(12, 12, 1, 0x90, 0x10, 18, 1), - - PIN_FIELD_BASE(19, 19, 4, 0x80, 0x10, 2, 1), - PIN_FIELD_BASE(20, 20, 4, 0x80, 0x10, 1, 1), - - PIN_FIELD_BASE(21, 21, 3, 0xb0, 0x10, 17, 1), - PIN_FIELD_BASE(22, 22, 3, 0xb0, 0x10, 23, 1), - PIN_FIELD_BASE(23, 23, 3, 0xb0, 0x10, 20, 1), - PIN_FIELD_BASE(24, 24, 3, 0xb0, 0x10, 19, 1), - PIN_FIELD_BASE(25, 25, 3, 0xb0, 0x10, 21, 1), - PIN_FIELD_BASE(26, 26, 3, 0xb0, 0x10, 22, 1), - PIN_FIELD_BASE(27, 27, 3, 0xb0, 0x10, 18, 1), - PIN_FIELD_BASE(28, 28, 3, 0xb0, 0x10, 25, 1), - PIN_FIELD_BASE(29, 29, 3, 0xb0, 0x10, 26, 1), - PIN_FIELD_BASE(30, 30, 3, 0xb0, 0x10, 27, 1), - PIN_FIELD_BASE(31, 31, 3, 0xb0, 0x10, 24, 1), - PIN_FIELD_BASE(32, 32, 3, 0xb0, 0x10, 28, 1), - PIN_FIELD_BASE(33, 33, 3, 0xc0, 0x10, 0, 1), - PIN_FIELD_BASE(34, 34, 3, 0xb0, 0x10, 31, 1), - PIN_FIELD_BASE(35, 35, 3, 0xb0, 0x10, 29, 1), - PIN_FIELD_BASE(36, 36, 3, 0xb0, 0x10, 30, 1), - PIN_FIELD_BASE(37, 37, 3, 0xc0, 0x10, 1, 1), - PIN_FIELD_BASE(38, 38, 3, 0xb0, 0x10, 11, 1), - PIN_FIELD_BASE(39, 39, 3, 0xb0, 0x10, 10, 1), - PIN_FIELD_BASE(40, 40, 3, 0xb0, 0x10, 0, 1), - PIN_FIELD_BASE(41, 41, 3, 0xb0, 0x10, 1, 1), - PIN_FIELD_BASE(42, 42, 3, 0xb0, 0x10, 9, 1), - PIN_FIELD_BASE(43, 43, 3, 0xb0, 0x10, 8, 1), - PIN_FIELD_BASE(44, 44, 3, 0xb0, 0x10, 7, 1), - PIN_FIELD_BASE(45, 45, 3, 0xb0, 0x10, 6, 1), - PIN_FIELD_BASE(46, 46, 3, 0xb0, 0x10, 5, 1), - PIN_FIELD_BASE(47, 47, 3, 0xb0, 0x10, 4, 1), - PIN_FIELD_BASE(48, 48, 3, 0xb0, 0x10, 3, 1), - PIN_FIELD_BASE(49, 49, 3, 0xb0, 0x10, 2, 1), - PIN_FIELD_BASE(50, 50, 3, 0xb0, 0x10, 15, 1), - PIN_FIELD_BASE(51, 51, 3, 0xb0, 0x10, 12, 1), - PIN_FIELD_BASE(52, 52, 3, 0xb0, 0x10, 13, 1), - PIN_FIELD_BASE(53, 53, 3, 0xb0, 0x10, 14, 1), - PIN_FIELD_BASE(54, 54, 3, 0xb0, 0x10, 16, 1), - - PIN_FIELD_BASE(55, 55, 1, 0x90, 0x10, 12, 1), - PIN_FIELD_BASE(56, 56, 1, 0x90, 0x10, 13, 1), - PIN_FIELD_BASE(57, 57, 1, 0x90, 0x10, 11, 1), - PIN_FIELD_BASE(58, 58, 1, 0x90, 0x10, 2, 1), - PIN_FIELD_BASE(59, 59, 1, 0x90, 0x10, 3, 1), - PIN_FIELD_BASE(60, 60, 1, 0x90, 0x10, 4, 1), - PIN_FIELD_BASE(61, 61, 1, 0x90, 0x10, 1, 1), - PIN_FIELD_BASE(62, 62, 1, 0x90, 0x10, 5, 1), - PIN_FIELD_BASE(64, 64, 1, 0x90, 0x10, 6, 1), - PIN_FIELD_BASE(65, 65, 1, 0x90, 0x10, 7, 1), - PIN_FIELD_BASE(66, 66, 1, 0x90, 0x10, 8, 1), - PIN_FIELD_BASE(67, 67, 1, 0x90, 0x10, 9, 1), - PIN_FIELD_BASE(68, 68, 1, 0x90, 0x10, 10, 1), - - PIN_FIELD_BASE(69, 69, 5, 0x70, 0x10, 1, 1), - PIN_FIELD_BASE(70, 70, 5, 0x70, 0x10, 2, 1), - - PIN_FIELD_BASE(73, 73, 4, 0x80, 0x10, 3, 1), - PIN_FIELD_BASE(74, 74, 4, 0x80, 0x10, 0, 1), - - PIN_FIELD_BASE(80, 80, 1, 0x90, 0x10, 16, 1), - PIN_FIELD_BASE(81, 81, 1, 0x90, 0x10, 17, 1), - PIN_FIELD_BASE(82, 82, 1, 0x90, 0x10, 14, 1), - PIN_FIELD_BASE(83, 83, 1, 0x90, 0x10, 15, 1), -}; - -static const struct mtk_pin_reg_calc mt7988_reg_cals[] = { - [PINCTRL_PIN_REG_MODE] = MTK_RANGE(mt7988_pin_mode_range), - [PINCTRL_PIN_REG_DIR] = MTK_RANGE(mt7988_pin_dir_range), - [PINCTRL_PIN_REG_DI] = MTK_RANGE(mt7988_pin_di_range), - [PINCTRL_PIN_REG_DO] = MTK_RANGE(mt7988_pin_do_range), - [PINCTRL_PIN_REG_SMT] = MTK_RANGE(mt7988_pin_smt_range), - [PINCTRL_PIN_REG_IES] = MTK_RANGE(mt7988_pin_ies_range), - [PINCTRL_PIN_REG_PU] = MTK_RANGE(mt7988_pin_pu_range), - [PINCTRL_PIN_REG_PD] = MTK_RANGE(mt7988_pin_pd_range), - [PINCTRL_PIN_REG_DRV] = MTK_RANGE(mt7988_pin_drv_range), - [PINCTRL_PIN_REG_PUPD] = MTK_RANGE(mt7988_pin_pupd_range), - [PINCTRL_PIN_REG_R0] = MTK_RANGE(mt7988_pin_r0_range), - [PINCTRL_PIN_REG_R1] = MTK_RANGE(mt7988_pin_r1_range), -}; - -static const struct mtk_pin_desc mt7988_pins[] = { - MT7988_PIN(0, "UART2_RXD"), - MT7988_PIN(1, "UART2_TXD"), - MT7988_PIN(2, "UART2_CTS"), - MT7988_PIN(3, "UART2_RTS"), - MT7988_PIN(4, "GPIO_A"), - MT7988_PIN(5, "SMI_0_MDC"), - MT7988_PIN(6, "SMI_0_MDIO"), - MT7988_PIN(7, "PCIE30_2L_0_WAKE_N"), - MT7988_PIN(8, "PCIE30_2L_0_CLKREQ_N"), - MT7988_PIN(9, "PCIE30_1L_1_WAKE_N"), - MT7988_PIN(10, "PCIE30_1L_1_CLKREQ_N"), - MT7988_PIN(11, "GPIO_P"), - MT7988_PIN(12, "WATCHDOG"), - MT7988_PIN(13, "GPIO_RESET"), - MT7988_PIN(14, "GPIO_WPS"), - MT7988_PIN(15, "PMIC_I2C_SCL"), - MT7988_PIN(16, "PMIC_I2C_SDA"), - MT7988_PIN(17, "I2C_1_SCL"), - MT7988_PIN(18, "I2C_1_SDA"), - MT7988_PIN(19, "PCIE30_2L_0_PRESET_N"), - MT7988_PIN(20, "PCIE30_1L_1_PRESET_N"), - MT7988_PIN(21, "PWMD1"), - MT7988_PIN(22, "SPI0_WP"), - MT7988_PIN(23, "SPI0_HOLD"), - MT7988_PIN(24, "SPI0_CSB"), - MT7988_PIN(25, "SPI0_MISO"), - MT7988_PIN(26, "SPI0_MOSI"), - MT7988_PIN(27, "SPI0_CLK"), - MT7988_PIN(28, "SPI1_CSB"), - MT7988_PIN(29, "SPI1_MISO"), - MT7988_PIN(30, "SPI1_MOSI"), - MT7988_PIN(31, "SPI1_CLK"), - MT7988_PIN(32, "SPI2_CLK"), - MT7988_PIN(33, "SPI2_MOSI"), - MT7988_PIN(34, "SPI2_MISO"), - MT7988_PIN(35, "SPI2_CSB"), - MT7988_PIN(36, "SPI2_HOLD"), - MT7988_PIN(37, "SPI2_WP"), - MT7988_PIN(38, "EMMC_RSTB"), - MT7988_PIN(39, "EMMC_DSL"), - MT7988_PIN(40, "EMMC_CK"), - MT7988_PIN(41, "EMMC_CMD"), - MT7988_PIN(42, "EMMC_DATA_7"), - MT7988_PIN(43, "EMMC_DATA_6"), - MT7988_PIN(44, "EMMC_DATA_5"), - MT7988_PIN(45, "EMMC_DATA_4"), - MT7988_PIN(46, "EMMC_DATA_3"), - MT7988_PIN(47, "EMMC_DATA_2"), - MT7988_PIN(48, "EMMC_DATA_1"), - MT7988_PIN(49, "EMMC_DATA_0"), - MT7988_PIN(50, "PCM_FS_I2S_LRCK"), - MT7988_PIN(51, "PCM_CLK_I2S_BCLK"), - MT7988_PIN(52, "PCM_DRX_I2S_DIN"), - MT7988_PIN(53, "PCM_DTX_I2S_DOUT"), - MT7988_PIN(54, "PCM_MCK_I2S_MCLK"), - MT7988_PIN(55, "UART0_RXD"), - MT7988_PIN(56, "UART0_TXD"), - MT7988_PIN(57, "PWMD0"), - MT7988_PIN(58, "JTAG_JTDI"), - MT7988_PIN(59, "JTAG_JTDO"), - MT7988_PIN(60, "JTAG_JTMS"), - MT7988_PIN(61, "JTAG_JTCLK"), - MT7988_PIN(62, "JTAG_JTRST_N"), - MT7988_PIN(63, "USB_DRV_VBUS_P1"), - MT7988_PIN(64, "LED_A"), - MT7988_PIN(65, "LED_B"), - MT7988_PIN(66, "LED_C"), - MT7988_PIN(67, "LED_D"), - MT7988_PIN(68, "LED_E"), - MT7988_PIN(69, "GPIO_B"), - MT7988_PIN(70, "GPIO_C"), - MT7988_PIN(71, "I2C_2_SCL"), - MT7988_PIN(72, "I2C_2_SDA"), - MT7988_PIN(73, "PCIE30_2L_1_PRESET_N"), - MT7988_PIN(74, "PCIE30_1L_0_PRESET_N"), - MT7988_PIN(75, "PCIE30_2L_1_WAKE_N"), - MT7988_PIN(76, "PCIE30_2L_1_CLKREQ_N"), - MT7988_PIN(77, "PCIE30_1L_0_WAKE_N"), - MT7988_PIN(78, "PCIE30_1L_0_CLKREQ_N"), - MT7988_PIN(79, "USB_DRV_VBUS_P0"), - MT7988_PIN(80, "UART1_RXD"), - MT7988_PIN(81, "UART1_TXD"), - MT7988_PIN(82, "UART1_CTS"), - MT7988_PIN(83, "UART1_RTS"), -}; - -/* jtag */ -static int mt7988_tops_jtag0_0_pins[] = { 0, 1, 2, 3, 4 }; -static int mt7988_tops_jtag0_0_funcs[] = { 2, 2, 2, 2, 2 }; - -static int mt7988_wo0_jtag_pins[] = { 50, 51, 52, 53, 54 }; -static int mt7988_wo0_jtag_funcs[] = { 3, 3, 3, 3, 3 }; - -static int mt7988_wo1_jtag_pins[] = { 50, 51, 52, 53, 54 }; -static int mt7988_wo1_jtag_funcs[] = { 4, 4, 4, 4, 4 }; - -static int mt7988_wo2_jtag_pins[] = { 50, 51, 52, 53, 54 }; -static int mt7988_wo2_jtag_funcs[] = { 5, 5, 5, 5, 5 }; - -static int mt7988_jtag_pins[] = { 58, 59, 60, 61, 62 }; -static int mt7988_jtag_funcs[] = { 1, 1, 1, 1, 1 }; - -static int mt7988_tops_jtag0_1_pins[] = { 58, 59, 60, 61, 62 }; -static int mt7988_tops_jtag0_1_funcs[] = { 4, 4, 4, 4, 4 }; - -/* int_usxgmii */ -static int mt7988_int_usxgmii_pins[] = { 2, 3 }; -static int mt7988_int_usxgmii_funcs[] = { 3, 3 }; - -/* pwm */ -static int mt7988_pwm0_pins[] = { 57 }; -static int mt7988_pwm0_funcs[] = { 1 }; - -static int mt7988_pwm1_pins[] = { 21 }; -static int mt7988_pwm1_funcs[] = { 1 }; - -static int mt7988_pwm2_pins[] = { 80 }; -static int mt7988_pwm2_funcs[] = { 2 }; - -static int mt7988_pwm3_pins[] = { 81 }; -static int mt7988_pwm3_funcs[] = { 2 }; - -static int mt7988_pwm4_pins[] = { 82 }; -static int mt7988_pwm4_funcs[] = { 2 }; - -static int mt7988_pwm5_pins[] = { 83 }; -static int mt7988_pwm5_funcs[] = { 2 }; - -static int mt7988_pwm6_pins[] = { 69 }; -static int mt7988_pwm6_funcs[] = { 3 }; - -static int mt7988_pwm7_pins[] = { 70 }; -static int mt7988_pwm7_funcs[] = { 3 }; - -/* dfd */ -static int mt7988_dfd_pins[] = { 0, 1, 2, 3, 4 }; -static int mt7988_dfd_funcs[] = { 4, 4, 4, 4, 4 }; - -/* i2c */ -static int mt7988_xfi_phy0_i2c0_pins[] = { 0, 1 }; -static int mt7988_xfi_phy0_i2c0_funcs[] = { 5, 5 }; - -static int mt7988_xfi_phy1_i2c0_pins[] = { 0, 1 }; -static int mt7988_xfi_phy1_i2c0_funcs[] = { 6, 6 }; - -static int mt7988_xfi_phy_pll_i2c0_pins[] = { 3, 4 }; -static int mt7988_xfi_phy_pll_i2c0_funcs[] = { 5, 5 }; - -static int mt7988_xfi_phy_pll_i2c1_pins[] = { 3, 4 }; -static int mt7988_xfi_phy_pll_i2c1_funcs[] = { 6, 6 }; - -static int mt7988_i2c0_0_pins[] = { 5, 6 }; -static int mt7988_i2c0_0_funcs[] = { 2, 2 }; - -static int mt7988_i2c1_sfp_pins[] = { 5, 6 }; -static int mt7988_i2c1_sfp_funcs[] = { 4, 4 }; - -static int mt7988_xfi_pextp_phy0_i2c_pins[] = { 5, 6 }; -static int mt7988_xfi_pextp_phy0_i2c_funcs[] = { 5, 5 }; - -static int mt7988_xfi_pextp_phy1_i2c_pins[] = { 5, 6 }; -static int mt7988_xfi_pextp_phy1_i2c_funcs[] = { 6, 6 }; - -static int mt7988_i2c0_1_pins[] = { 15, 16 }; -static int mt7988_i2c0_1_funcs[] = { 1, 1 }; - -static int mt7988_u30_phy_i2c0_pins[] = { 15, 16 }; -static int mt7988_u30_phy_i2c0_funcs[] = { 2, 2 }; - -static int mt7988_u32_phy_i2c0_pins[] = { 15, 16 }; -static int mt7988_u32_phy_i2c0_funcs[] = { 3, 3 }; - -static int mt7988_xfi_phy0_i2c1_pins[] = { 15, 16 }; -static int mt7988_xfi_phy0_i2c1_funcs[] = { 5, 5 }; - -static int mt7988_xfi_phy1_i2c1_pins[] = { 15, 16 }; -static int mt7988_xfi_phy1_i2c1_funcs[] = { 6, 6 }; - -static int mt7988_xfi_phy_pll_i2c2_pins[] = { 15, 16 }; -static int mt7988_xfi_phy_pll_i2c2_funcs[] = { 7, 7 }; - -static int mt7988_i2c1_0_pins[] = { 17, 18 }; -static int mt7988_i2c1_0_funcs[] = { 1, 1 }; - -static int mt7988_u30_phy_i2c1_pins[] = { 17, 18 }; -static int mt7988_u30_phy_i2c1_funcs[] = { 2, 2 }; - -static int mt7988_u32_phy_i2c1_pins[] = { 17, 18 }; -static int mt7988_u32_phy_i2c1_funcs[] = { 3, 3 }; - -static int mt7988_xfi_phy_pll_i2c3_pins[] = { 17, 18 }; -static int mt7988_xfi_phy_pll_i2c3_funcs[] = { 4, 4 }; - -static int mt7988_sgmii0_i2c_pins[] = { 17, 18 }; -static int mt7988_sgmii0_i2c_funcs[] = { 5, 5 }; - -static int mt7988_sgmii1_i2c_pins[] = { 17, 18 }; -static int mt7988_sgmii1_i2c_funcs[] = { 6, 6 }; - -static int mt7988_i2c1_2_pins[] = { 69, 70 }; -static int mt7988_i2c1_2_funcs[] = { 2, 2 }; - -static int mt7988_i2c2_0_pins[] = { 69, 70 }; -static int mt7988_i2c2_0_funcs[] = { 4, 4 }; - -static int mt7988_i2c2_1_pins[] = { 71, 72 }; -static int mt7988_i2c2_1_funcs[] = { 1, 1 }; - -/* eth */ -static int mt7988_mdc_mdio0_pins[] = { 5, 6 }; -static int mt7988_mdc_mdio0_funcs[] = { 1, 1 }; - -static int mt7988_2p5g_ext_mdio_pins[] = { 28, 29 }; -static int mt7988_2p5g_ext_mdio_funcs[] = { 6, 6 }; - -static int mt7988_gbe_ext_mdio_pins[] = { 30, 31 }; -static int mt7988_gbe_ext_mdio_funcs[] = { 6, 6 }; - -static int mt7988_mdc_mdio1_pins[] = { 69, 70 }; -static int mt7988_mdc_mdio1_funcs[] = { 1, 1 }; - -/* pcie */ -static int mt7988_pcie_wake_n0_0_pins[] = { 7 }; -static int mt7988_pcie_wake_n0_0_funcs[] = { 1 }; - -static int mt7988_pcie_clk_req_n0_0_pins[] = { 8 }; -static int mt7988_pcie_clk_req_n0_0_funcs[] = { 1 }; - -static int mt7988_pcie_wake_n3_0_pins[] = { 9 }; -static int mt7988_pcie_wake_n3_0_funcs[] = { 1 }; - -static int mt7988_pcie_clk_req_n3_pins[] = { 10 }; -static int mt7988_pcie_clk_req_n3_funcs[] = { 1 }; - -static int mt7988_pcie_clk_req_n0_1_pins[] = { 10 }; -static int mt7988_pcie_clk_req_n0_1_funcs[] = { 2 }; - -static int mt7988_pcie_p0_phy_i2c_pins[] = { 7, 8 }; -static int mt7988_pcie_p0_phy_i2c_funcs[] = { 3, 3 }; - -static int mt7988_pcie_p1_phy_i2c_pins[] = { 7, 8 }; -static int mt7988_pcie_p1_phy_i2c_funcs[] = { 4, 4 }; - -static int mt7988_pcie_p3_phy_i2c_pins[] = { 9, 10 }; -static int mt7988_pcie_p3_phy_i2c_funcs[] = { 4, 4 }; - -static int mt7988_pcie_p2_phy_i2c_pins[] = { 7, 8 }; -static int mt7988_pcie_p2_phy_i2c_funcs[] = { 5, 5 }; - -static int mt7988_ckm_phy_i2c_pins[] = { 9, 10 }; -static int mt7988_ckm_phy_i2c_funcs[] = { 5, 5 }; - -static int mt7988_pcie_wake_n0_1_pins[] = { 13 }; -static int mt7988_pcie_wake_n0_1_funcs[] = { 2 }; - -static int mt7988_pcie_wake_n3_1_pins[] = { 14 }; -static int mt7988_pcie_wake_n3_1_funcs[] = { 2 }; - -static int mt7988_pcie_2l_0_pereset_pins[] = { 19 }; -static int mt7988_pcie_2l_0_pereset_funcs[] = { 1 }; - -static int mt7988_pcie_1l_1_pereset_pins[] = { 20 }; -static int mt7988_pcie_1l_1_pereset_funcs[] = { 1 }; - -static int mt7988_pcie_clk_req_n2_1_pins[] = { 63 }; -static int mt7988_pcie_clk_req_n2_1_funcs[] = { 2 }; - -static int mt7988_pcie_2l_1_pereset_pins[] = { 73 }; -static int mt7988_pcie_2l_1_pereset_funcs[] = { 1 }; - -static int mt7988_pcie_1l_0_pereset_pins[] = { 74 }; -static int mt7988_pcie_1l_0_pereset_funcs[] = { 1 }; - -static int mt7988_pcie_wake_n1_0_pins[] = { 75 }; -static int mt7988_pcie_wake_n1_0_funcs[] = { 1 }; - -static int mt7988_pcie_clk_req_n1_pins[] = { 76 }; -static int mt7988_pcie_clk_req_n1_funcs[] = { 1 }; - -static int mt7988_pcie_wake_n2_0_pins[] = { 77 }; -static int mt7988_pcie_wake_n2_0_funcs[] = { 1 }; - -static int mt7988_pcie_clk_req_n2_0_pins[] = { 78 }; -static int mt7988_pcie_clk_req_n2_0_funcs[] = { 1 }; - -static int mt7988_pcie_wake_n2_1_pins[] = { 79 }; -static int mt7988_pcie_wake_n2_1_funcs[] = { 2 }; - -/* pmic */ -static int mt7988_pmic_pins[] = { 11 }; -static int mt7988_pmic_funcs[] = { 1 }; - -/* watchdog */ -static int mt7988_watchdog_pins[] = { 12 }; -static int mt7988_watchdog_funcs[] = { 1 }; - -/* spi */ -static int mt7988_spi0_wp_hold_pins[] = { 22, 23 }; -static int mt7988_spi0_wp_hold_funcs[] = { 1, 1 }; - -static int mt7988_spi0_pins[] = { 24, 25, 26, 27 }; -static int mt7988_spi0_funcs[] = { 1, 1, 1, 1 }; - -static int mt7988_spi1_pins[] = { 28, 29, 30, 31 }; -static int mt7988_spi1_funcs[] = { 1, 1, 1, 1 }; - -static int mt7988_spi2_pins[] = { 32, 33, 34, 35 }; -static int mt7988_spi2_funcs[] = { 1, 1, 1, 1 }; - -static int mt7988_spi2_wp_hold_pins[] = { 36, 37 }; -static int mt7988_spi2_wp_hold_funcs[] = { 1, 1 }; - -/* flash */ -static int mt7988_snfi_pins[] = { 22, 23, 24, 25, 26, 27 }; -static int mt7988_snfi_funcs[] = { 2, 2, 2, 2, 2, 2 }; - -static int mt7988_emmc_45_pins[] = { - 21, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37 -}; -static int mt7988_emmc_45_funcs[] = { 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5 }; - -static int mt7988_sdcard_pins[] = { 32, 33, 34, 35, 36, 37 }; -static int mt7988_sdcard_funcs[] = { 5, 5, 5, 5, 5, 5 }; - -static int mt7988_emmc_51_pins[] = { 38, 39, 40, 41, 42, 43, - 44, 45, 46, 47, 48, 49 }; -static int mt7988_emmc_51_funcs[] = { 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1 }; - -/* uart */ -static int mt7988_uart2_pins[] = { 0, 1, 2, 3 }; -static int mt7988_uart2_funcs[] = { 1, 1, 1, 1 }; - -static int mt7988_tops_uart0_0_pins[] = { 22, 23 }; -static int mt7988_tops_uart0_0_funcs[] = { 3, 3 }; - -static int mt7988_uart2_0_pins[] = { 28, 29, 30, 31 }; -static int mt7988_uart2_0_funcs[] = { 2, 2, 2, 2 }; - -static int mt7988_uart1_0_pins[] = { 32, 33, 34, 35 }; -static int mt7988_uart1_0_funcs[] = { 2, 2, 2, 2 }; - -static int mt7988_uart2_1_pins[] = { 32, 33, 34, 35 }; -static int mt7988_uart2_1_funcs[] = { 3, 3, 3, 3 }; - -static int mt7988_net_wo0_uart_txd_0_pins[] = { 28 }; -static int mt7988_net_wo0_uart_txd_0_funcs[] = { 3 }; - -static int mt7988_net_wo1_uart_txd_0_pins[] = { 29 }; -static int mt7988_net_wo1_uart_txd_0_funcs[] = { 3 }; - -static int mt7988_net_wo2_uart_txd_0_pins[] = { 30 }; -static int mt7988_net_wo2_uart_txd_0_funcs[] = { 3 }; - -static int mt7988_tops_uart1_0_pins[] = { 28, 29 }; -static int mt7988_tops_uart1_0_funcs[] = { 4, 4 }; - -static int mt7988_tops_uart0_1_pins[] = { 30, 31 }; -static int mt7988_tops_uart0_1_funcs[] = { 4, 4 }; - -static int mt7988_tops_uart1_1_pins[] = { 36, 37 }; -static int mt7988_tops_uart1_1_funcs[] = { 3, 3 }; - -static int mt7988_uart0_pins[] = { 55, 56 }; -static int mt7988_uart0_funcs[] = { 1, 1 }; - -static int mt7988_tops_uart0_2_pins[] = { 55, 56 }; -static int mt7988_tops_uart0_2_funcs[] = { 2, 2 }; - -static int mt7988_uart2_2_pins[] = { 50, 51, 52, 53 }; -static int mt7988_uart2_2_funcs[] = { 2, 2, 2, 2 }; - -static int mt7988_uart1_1_pins[] = { 58, 59, 60, 61 }; -static int mt7988_uart1_1_funcs[] = { 2, 2, 2, 2 }; - -static int mt7988_uart2_3_pins[] = { 58, 59, 60, 61 }; -static int mt7988_uart2_3_funcs[] = { 3, 3, 3, 3 }; - -static int mt7988_uart1_2_pins[] = { 80, 81, 82, 83 }; -static int mt7988_uart1_2_funcs[] = { 1, 1, 1, 1 }; - -static int mt7988_tops_uart1_2_pins[] = { 80, 81 }; -static int mt7988_tops_uart1_2_funcs[] = { - 4, - 4, -}; - -static int mt7988_net_wo0_uart_txd_1_pins[] = { 80 }; -static int mt7988_net_wo0_uart_txd_1_funcs[] = { 3 }; - -static int mt7988_net_wo1_uart_txd_1_pins[] = { 81 }; -static int mt7988_net_wo1_uart_txd_1_funcs[] = { 3 }; - -static int mt7988_net_wo2_uart_txd_1_pins[] = { 82 }; -static int mt7988_net_wo2_uart_txd_1_funcs[] = { 3 }; - -/* udi */ -static int mt7988_udi_pins[] = { 32, 33, 34, 35, 36 }; -static int mt7988_udi_funcs[] = { 4, 4, 4, 4, 4 }; - -/* i2s */ -static int mt7988_i2s_pins[] = { 50, 51, 52, 53, 54 }; -static int mt7988_i2s_funcs[] = { 1, 1, 1, 1, 1 }; - -/* pcm */ -static int mt7988_pcm_pins[] = { 50, 51, 52, 53 }; -static int mt7988_pcm_funcs[] = { 1, 1, 1, 1 }; - -/* led */ -static int mt7988_gbe0_led1_pins[] = { 58 }; -static int mt7988_gbe0_led1_funcs[] = { 6 }; -static int mt7988_gbe1_led1_pins[] = { 59 }; -static int mt7988_gbe1_led1_funcs[] = { 6 }; -static int mt7988_gbe2_led1_pins[] = { 60 }; -static int mt7988_gbe2_led1_funcs[] = { 6 }; -static int mt7988_gbe3_led1_pins[] = { 61 }; -static int mt7988_gbe3_led1_funcs[] = { 6 }; - -static int mt7988_2p5gbe_led1_pins[] = { 62 }; -static int mt7988_2p5gbe_led1_funcs[] = { 6 }; - -static int mt7988_gbe0_led0_pins[] = { 64 }; -static int mt7988_gbe0_led0_funcs[] = { 1 }; -static int mt7988_gbe1_led0_pins[] = { 65 }; -static int mt7988_gbe1_led0_funcs[] = { 1 }; -static int mt7988_gbe2_led0_pins[] = { 66 }; -static int mt7988_gbe2_led0_funcs[] = { 1 }; -static int mt7988_gbe3_led0_pins[] = { 67 }; -static int mt7988_gbe3_led0_funcs[] = { 1 }; - -static int mt7988_2p5gbe_led0_pins[] = { 68 }; -static int mt7988_2p5gbe_led0_funcs[] = { 1 }; - -/* usb */ -static int mt7988_drv_vbus_p1_pins[] = { 63 }; -static int mt7988_drv_vbus_p1_funcs[] = { 1 }; - -static int mt7988_drv_vbus_pins[] = { 79 }; -static int mt7988_drv_vbus_funcs[] = { 1 }; - -static const struct group_desc mt7988_groups[] = { - /* @GPIO(0,1,2,3): uart2 */ - PINCTRL_PIN_GROUP("uart2", mt7988_uart2), - /* @GPIO(0,1,2,3,4): tops_jtag0_0 */ - PINCTRL_PIN_GROUP("tops_jtag0_0", mt7988_tops_jtag0_0), - /* @GPIO(2,3): int_usxgmii */ - PINCTRL_PIN_GROUP("int_usxgmii", mt7988_int_usxgmii), - /* @GPIO(0,1,2,3,4): dfd */ - PINCTRL_PIN_GROUP("dfd", mt7988_dfd), - /* @GPIO(0,1): xfi_phy0_i2c0 */ - PINCTRL_PIN_GROUP("xfi_phy0_i2c0", mt7988_xfi_phy0_i2c0), - /* @GPIO(0,1): xfi_phy1_i2c0 */ - PINCTRL_PIN_GROUP("xfi_phy1_i2c0", mt7988_xfi_phy1_i2c0), - /* @GPIO(3,4): xfi_phy_pll_i2c0 */ - PINCTRL_PIN_GROUP("xfi_phy_pll_i2c0", mt7988_xfi_phy_pll_i2c0), - /* @GPIO(3,4): xfi_phy_pll_i2c1 */ - PINCTRL_PIN_GROUP("xfi_phy_pll_i2c1", mt7988_xfi_phy_pll_i2c1), - /* @GPIO(5,6) i2c0_0 */ - PINCTRL_PIN_GROUP("i2c0_0", mt7988_i2c0_0), - /* @GPIO(5,6) i2c1_sfp */ - PINCTRL_PIN_GROUP("i2c1_sfp", mt7988_i2c1_sfp), - /* @GPIO(5,6) xfi_pextp_phy0_i2c */ - PINCTRL_PIN_GROUP("xfi_pextp_phy0_i2c", mt7988_xfi_pextp_phy0_i2c), - /* @GPIO(5,6) xfi_pextp_phy1_i2c */ - PINCTRL_PIN_GROUP("xfi_pextp_phy1_i2c", mt7988_xfi_pextp_phy1_i2c), - /* @GPIO(5,6) mdc_mdio0 */ - PINCTRL_PIN_GROUP("mdc_mdio0", mt7988_mdc_mdio0), - /* @GPIO(7): pcie_wake_n0_0 */ - PINCTRL_PIN_GROUP("pcie_wake_n0_0", mt7988_pcie_wake_n0_0), - /* @GPIO(8): pcie_clk_req_n0_0 */ - PINCTRL_PIN_GROUP("pcie_clk_req_n0_0", mt7988_pcie_clk_req_n0_0), - /* @GPIO(9): pcie_wake_n3_0 */ - PINCTRL_PIN_GROUP("pcie_wake_n3_0", mt7988_pcie_wake_n3_0), - /* @GPIO(10): pcie_clk_req_n3 */ - PINCTRL_PIN_GROUP("pcie_clk_req_n3", mt7988_pcie_clk_req_n3), - /* @GPIO(10): pcie_clk_req_n0_1 */ - PINCTRL_PIN_GROUP("pcie_clk_req_n0_1", mt7988_pcie_clk_req_n0_1), - /* @GPIO(7,8) pcie_p0_phy_i2c */ - PINCTRL_PIN_GROUP("pcie_p0_phy_i2c", mt7988_pcie_p0_phy_i2c), - /* @GPIO(7,8) pcie_p1_phy_i2c */ - PINCTRL_PIN_GROUP("pcie_p1_phy_i2c", mt7988_pcie_p1_phy_i2c), - /* @GPIO(7,8) pcie_p2_phy_i2c */ - PINCTRL_PIN_GROUP("pcie_p2_phy_i2c", mt7988_pcie_p2_phy_i2c), - /* @GPIO(9,10) pcie_p3_phy_i2c */ - PINCTRL_PIN_GROUP("pcie_p3_phy_i2c", mt7988_pcie_p3_phy_i2c), - /* @GPIO(9,10) ckm_phy_i2c */ - PINCTRL_PIN_GROUP("ckm_phy_i2c", mt7988_ckm_phy_i2c), - /* @GPIO(11): pmic */ - PINCTRL_PIN_GROUP("pcie_pmic", mt7988_pmic), - /* @GPIO(12): watchdog */ - PINCTRL_PIN_GROUP("watchdog", mt7988_watchdog), - /* @GPIO(13): pcie_wake_n0_1 */ - PINCTRL_PIN_GROUP("pcie_wake_n0_1", mt7988_pcie_wake_n0_1), - /* @GPIO(14): pcie_wake_n3_1 */ - PINCTRL_PIN_GROUP("pcie_wake_n3_1", mt7988_pcie_wake_n3_1), - /* @GPIO(15,16) i2c0_1 */ - PINCTRL_PIN_GROUP("i2c0_1", mt7988_i2c0_1), - /* @GPIO(15,16) u30_phy_i2c0 */ - PINCTRL_PIN_GROUP("u30_phy_i2c0", mt7988_u30_phy_i2c0), - /* @GPIO(15,16) u32_phy_i2c0 */ - PINCTRL_PIN_GROUP("u32_phy_i2c0", mt7988_u32_phy_i2c0), - /* @GPIO(15,16) xfi_phy0_i2c1 */ - PINCTRL_PIN_GROUP("xfi_phy0_i2c1", mt7988_xfi_phy0_i2c1), - /* @GPIO(15,16) xfi_phy1_i2c1 */ - PINCTRL_PIN_GROUP("xfi_phy1_i2c1", mt7988_xfi_phy1_i2c1), - /* @GPIO(15,16) xfi_phy_pll_i2c2 */ - PINCTRL_PIN_GROUP("xfi_phy_pll_i2c2", mt7988_xfi_phy_pll_i2c2), - /* @GPIO(17,18) i2c1_0 */ - PINCTRL_PIN_GROUP("i2c1_0", mt7988_i2c1_0), - /* @GPIO(17,18) u30_phy_i2c1 */ - PINCTRL_PIN_GROUP("u30_phy_i2c1", mt7988_u30_phy_i2c1), - /* @GPIO(17,18) u32_phy_i2c1 */ - PINCTRL_PIN_GROUP("u32_phy_i2c1", mt7988_u32_phy_i2c1), - /* @GPIO(17,18) xfi_phy_pll_i2c3 */ - PINCTRL_PIN_GROUP("xfi_phy_pll_i2c3", mt7988_xfi_phy_pll_i2c3), - /* @GPIO(17,18) sgmii0_i2c */ - PINCTRL_PIN_GROUP("sgmii0_i2c", mt7988_sgmii0_i2c), - /* @GPIO(17,18) sgmii1_i2c */ - PINCTRL_PIN_GROUP("sgmii1_i2c", mt7988_sgmii1_i2c), - /* @GPIO(19): pcie_2l_0_pereset */ - PINCTRL_PIN_GROUP("pcie_2l_0_pereset", mt7988_pcie_2l_0_pereset), - /* @GPIO(20): pcie_1l_1_pereset */ - PINCTRL_PIN_GROUP("pcie_1l_1_pereset", mt7988_pcie_1l_1_pereset), - /* @GPIO(21): pwm1 */ - PINCTRL_PIN_GROUP("pwm1", mt7988_pwm1), - /* @GPIO(22,23) spi0_wp_hold */ - PINCTRL_PIN_GROUP("spi0_wp_hold", mt7988_spi0_wp_hold), - /* @GPIO(24,25,26,27) spi0 */ - PINCTRL_PIN_GROUP("spi0", mt7988_spi0), - /* @GPIO(28,29,30,31) spi1 */ - PINCTRL_PIN_GROUP("spi1", mt7988_spi1), - /* @GPIO(32,33,34,35) spi2 */ - PINCTRL_PIN_GROUP("spi2", mt7988_spi2), - /* @GPIO(36,37) spi2_wp_hold */ - PINCTRL_PIN_GROUP("spi2_wp_hold", mt7988_spi2_wp_hold), - /* @GPIO(22,23,24,25,26,27) snfi */ - PINCTRL_PIN_GROUP("snfi", mt7988_snfi), - /* @GPIO(22,23) tops_uart0_0 */ - PINCTRL_PIN_GROUP("tops_uart0_0", mt7988_tops_uart0_0), - /* @GPIO(28,29,30,31) uart2_0 */ - PINCTRL_PIN_GROUP("uart2_0", mt7988_uart2_0), - /* @GPIO(32,33,34,35) uart1_0 */ - PINCTRL_PIN_GROUP("uart1_0", mt7988_uart1_0), - /* @GPIO(32,33,34,35) uart2_1 */ - PINCTRL_PIN_GROUP("uart2_1", mt7988_uart2_1), - /* @GPIO(28) net_wo0_uart_txd_0 */ - PINCTRL_PIN_GROUP("net_wo0_uart_txd_0", mt7988_net_wo0_uart_txd_0), - /* @GPIO(29) net_wo1_uart_txd_0 */ - PINCTRL_PIN_GROUP("net_wo1_uart_txd_0", mt7988_net_wo1_uart_txd_0), - /* @GPIO(30) net_wo2_uart_txd_0 */ - PINCTRL_PIN_GROUP("net_wo2_uart_txd_0", mt7988_net_wo2_uart_txd_0), - /* @GPIO(28,29) tops_uart1_0 */ - PINCTRL_PIN_GROUP("tops_uart0_0", mt7988_tops_uart1_0), - /* @GPIO(30,31) tops_uart0_1 */ - PINCTRL_PIN_GROUP("tops_uart0_1", mt7988_tops_uart0_1), - /* @GPIO(36,37) tops_uart1_1 */ - PINCTRL_PIN_GROUP("tops_uart1_1", mt7988_tops_uart1_1), - /* @GPIO(32,33,34,35,36) udi */ - PINCTRL_PIN_GROUP("udi", mt7988_udi), - /* @GPIO(21,28,29,30,31,32,33,34,35,36,37) emmc_45 */ - PINCTRL_PIN_GROUP("emmc_45", mt7988_emmc_45), - /* @GPIO(32,33,34,35,36,37) sdcard */ - PINCTRL_PIN_GROUP("sdcard", mt7988_sdcard), - /* @GPIO(38,39,40,41,42,43,44,45,46,47,48,49) emmc_51 */ - PINCTRL_PIN_GROUP("emmc_51", mt7988_emmc_51), - /* @GPIO(28,29) 2p5g_ext_mdio */ - PINCTRL_PIN_GROUP("2p5g_ext_mdio", mt7988_2p5g_ext_mdio), - /* @GPIO(30,31) gbe_ext_mdio */ - PINCTRL_PIN_GROUP("gbe_ext_mdio", mt7988_gbe_ext_mdio), - /* @GPIO(50,51,52,53,54) i2s */ - PINCTRL_PIN_GROUP("i2s", mt7988_i2s), - /* @GPIO(50,51,52,53) pcm */ - PINCTRL_PIN_GROUP("pcm", mt7988_pcm), - /* @GPIO(55,56) uart0 */ - PINCTRL_PIN_GROUP("uart0", mt7988_uart0), - /* @GPIO(55,56) tops_uart0_2 */ - PINCTRL_PIN_GROUP("tops_uart0_2", mt7988_tops_uart0_2), - /* @GPIO(50,51,52,53) uart2_2 */ - PINCTRL_PIN_GROUP("uart2_2", mt7988_uart2_2), - /* @GPIO(50,51,52,53,54) wo0_jtag */ - PINCTRL_PIN_GROUP("wo0_jtag", mt7988_wo0_jtag), - /* @GPIO(50,51,52,53,54) wo1-wo1_jtag */ - PINCTRL_PIN_GROUP("wo1_jtag", mt7988_wo1_jtag), - /* @GPIO(50,51,52,53,54) wo2_jtag */ - PINCTRL_PIN_GROUP("wo2_jtag", mt7988_wo2_jtag), - /* @GPIO(57) pwm0 */ - PINCTRL_PIN_GROUP("pwm0", mt7988_pwm0), - /* @GPIO(58,59,60,61,62) jtag */ - PINCTRL_PIN_GROUP("jtag", mt7988_jtag), - /* @GPIO(58,59,60,61,62) tops_jtag0_1 */ - PINCTRL_PIN_GROUP("tops_jtag0_1", mt7988_tops_jtag0_1), - /* @GPIO(58,59,60,61) uart2_3 */ - PINCTRL_PIN_GROUP("uart2_3", mt7988_uart2_3), - /* @GPIO(58,59,60,61) uart1_1 */ - PINCTRL_PIN_GROUP("uart1_1", mt7988_uart1_1), - /* @GPIO(58,59,60,61) gbe_led1 */ - PINCTRL_PIN_GROUP("gbe0_led1", mt7988_gbe0_led1), - PINCTRL_PIN_GROUP("gbe1_led1", mt7988_gbe1_led1), - PINCTRL_PIN_GROUP("gbe2_led1", mt7988_gbe2_led1), - PINCTRL_PIN_GROUP("gbe3_led1", mt7988_gbe3_led1), - /* @GPIO(62) 2p5gbe_led1 */ - PINCTRL_PIN_GROUP("2p5gbe_led1", mt7988_2p5gbe_led1), - /* @GPIO(64,65,66,67) gbe_led0 */ - PINCTRL_PIN_GROUP("gbe0_led0", mt7988_gbe0_led0), - PINCTRL_PIN_GROUP("gbe1_led0", mt7988_gbe1_led0), - PINCTRL_PIN_GROUP("gbe2_led0", mt7988_gbe2_led0), - PINCTRL_PIN_GROUP("gbe3_led0", mt7988_gbe3_led0), - /* @GPIO(68) 2p5gbe_led0 */ - PINCTRL_PIN_GROUP("2p5gbe_led0", mt7988_2p5gbe_led0), - /* @GPIO(63) drv_vbus_p1 */ - PINCTRL_PIN_GROUP("drv_vbus_p1", mt7988_drv_vbus_p1), - /* @GPIO(63) pcie_clk_req_n2_1 */ - PINCTRL_PIN_GROUP("pcie_clk_req_n2_1", mt7988_pcie_clk_req_n2_1), - /* @GPIO(69, 70) mdc_mdio1 */ - PINCTRL_PIN_GROUP("mdc_mdio1", mt7988_mdc_mdio1), - /* @GPIO(69, 70) i2c1_2 */ - PINCTRL_PIN_GROUP("i2c1_2", mt7988_i2c1_2), - /* @GPIO(69) pwm6 */ - PINCTRL_PIN_GROUP("pwm6", mt7988_pwm6), - /* @GPIO(70) pwm7 */ - PINCTRL_PIN_GROUP("pwm7", mt7988_pwm7), - /* @GPIO(69,70) i2c2_0 */ - PINCTRL_PIN_GROUP("i2c2_0", mt7988_i2c2_0), - /* @GPIO(71,72) i2c2_1 */ - PINCTRL_PIN_GROUP("i2c2_1", mt7988_i2c2_1), - /* @GPIO(73) pcie_2l_1_pereset */ - PINCTRL_PIN_GROUP("pcie_2l_1_pereset", mt7988_pcie_2l_1_pereset), - /* @GPIO(74) pcie_1l_0_pereset */ - PINCTRL_PIN_GROUP("pcie_1l_0_pereset", mt7988_pcie_1l_0_pereset), - /* @GPIO(75) pcie_wake_n1_0 */ - PINCTRL_PIN_GROUP("pcie_wake_n1_0", mt7988_pcie_wake_n1_0), - /* @GPIO(76) pcie_clk_req_n1 */ - PINCTRL_PIN_GROUP("pcie_clk_req_n1", mt7988_pcie_clk_req_n1), - /* @GPIO(77) pcie_wake_n2_0 */ - PINCTRL_PIN_GROUP("pcie_wake_n2_0", mt7988_pcie_wake_n2_0), - /* @GPIO(78) pcie_clk_req_n2_0 */ - PINCTRL_PIN_GROUP("pcie_clk_req_n2_0", mt7988_pcie_clk_req_n2_0), - /* @GPIO(79) drv_vbus */ - PINCTRL_PIN_GROUP("drv_vbus", mt7988_drv_vbus), - /* @GPIO(79) pcie_wake_n2_1 */ - PINCTRL_PIN_GROUP("pcie_wake_n2_1", mt7988_pcie_wake_n2_1), - /* @GPIO(80,81,82,83) uart1_2 */ - PINCTRL_PIN_GROUP("uart1_2", mt7988_uart1_2), - /* @GPIO(80) pwm2 */ - PINCTRL_PIN_GROUP("pwm2", mt7988_pwm2), - /* @GPIO(81) pwm3 */ - PINCTRL_PIN_GROUP("pwm3", mt7988_pwm3), - /* @GPIO(82) pwm4 */ - PINCTRL_PIN_GROUP("pwm4", mt7988_pwm4), - /* @GPIO(83) pwm5 */ - PINCTRL_PIN_GROUP("pwm5", mt7988_pwm5), - /* @GPIO(80) net_wo0_uart_txd_0 */ - PINCTRL_PIN_GROUP("net_wo0_uart_txd_0", mt7988_net_wo0_uart_txd_0), - /* @GPIO(81) net_wo1_uart_txd_0 */ - PINCTRL_PIN_GROUP("net_wo1_uart_txd_0", mt7988_net_wo1_uart_txd_0), - /* @GPIO(82) net_wo2_uart_txd_0 */ - PINCTRL_PIN_GROUP("net_wo2_uart_txd_0", mt7988_net_wo2_uart_txd_0), - /* @GPIO(80,81) tops_uart1_2 */ - PINCTRL_PIN_GROUP("tops_uart1_2", mt7988_tops_uart1_2), - /* @GPIO(80) net_wo0_uart_txd_1 */ - PINCTRL_PIN_GROUP("net_wo0_uart_txd_1", mt7988_net_wo0_uart_txd_1), - /* @GPIO(81) net_wo1_uart_txd_1 */ - PINCTRL_PIN_GROUP("net_wo1_uart_txd_1", mt7988_net_wo1_uart_txd_1), - /* @GPIO(82) net_wo2_uart_txd_1 */ - PINCTRL_PIN_GROUP("net_wo2_uart_txd_1", mt7988_net_wo2_uart_txd_1), -}; - -/* Joint those groups owning the same capability in user point of view which - * allows that people tend to use through the device tree. - */ -static const char *mt7988_jtag_groups[] = { - "tops_jtag0_0", "wo0_jtag", "wo1_jtag", - "wo2_jtag", "jtag", "tops_jtag0_1", -}; -static const char *mt7988_int_usxgmii_groups[] = { - "int_usxgmii", -}; -static const char *mt7988_pwm_groups[] = { - "pwm0", "pwm1", "pwm2", "pwm3", "pwm4", "pwm5", "pwm6", "pwm7" -}; -static const char *mt7988_dfd_groups[] = { - "dfd", -}; -static const char *mt7988_i2c_groups[] = { - "xfi_phy0_i2c0", - "xfi_phy1_i2c0", - "xfi_phy_pll_i2c0", - "xfi_phy_pll_i2c1", - "i2c0_0", - "i2c1_sfp", - "xfi_pextp_phy0_i2c", - "xfi_pextp_phy1_i2c", - "i2c0_1", - "u30_phy_i2c0", - "u32_phy_i2c0", - "xfi_phy0_i2c1", - "xfi_phy1_i2c1", - "xfi_phy_pll_i2c2", - "i2c1_0", - "u30_phy_i2c1", - "u32_phy_i2c1", - "xfi_phy_pll_i2c3", - "sgmii0_i2c", - "sgmii1_i2c", - "i2c1_2", - "i2c2_0", - "i2c2_1", -}; -static const char *mt7988_ethernet_groups[] = { - "mdc_mdio0", - "2p5g_ext_mdio", - "gbe_ext_mdio", - "mdc_mdio1", -}; -static const char *mt7988_pcie_groups[] = { - "pcie_wake_n0_0", "pcie_clk_req_n0_0", "pcie_wake_n3_0", - "pcie_clk_req_n3", "pcie_p0_phy_i2c", "pcie_p1_phy_i2c", - "pcie_p3_phy_i2c", "pcie_p2_phy_i2c", "ckm_phy_i2c", - "pcie_wake_n0_1", "pcie_wake_n3_1", "pcie_2l_0_pereset", - "pcie_1l_1_pereset", "pcie_clk_req_n2_1", "pcie_2l_1_pereset", - "pcie_1l_0_pereset", "pcie_wake_n1_0", "pcie_clk_req_n1", - "pcie_wake_n2_0", "pcie_clk_req_n2_0", "pcie_wake_n2_1", - "pcie_clk_req_n0_1" -}; -static const char *mt7988_pmic_groups[] = { - "pmic", -}; -static const char *mt7988_wdt_groups[] = { - "watchdog", -}; -static const char *mt7988_spi_groups[] = { - "spi0", "spi0_wp_hold", "spi1", "spi2", "spi2_wp_hold", -}; -static const char *mt7988_flash_groups[] = { "emmc_45", "sdcard", "snfi", - "emmc_51" }; -static const char *mt7988_uart_groups[] = { - "uart2", - "tops_uart0_0", - "uart2_0", - "uart1_0", - "uart2_1", - "net_wo0_uart_txd_0", - "net_wo1_uart_txd_0", - "net_wo2_uart_txd_0", - "tops_uart1_0", - "ops_uart0_1", - "ops_uart1_1", - "uart0", - "tops_uart0_2", - "uart1_1", - "uart2_3", - "uart1_2", - "tops_uart1_2", - "net_wo0_uart_txd_1", - "net_wo1_uart_txd_1", - "net_wo2_uart_txd_1", -}; -static const char *mt7988_udi_groups[] = { - "udi", -}; -static const char *mt7988_audio_groups[] = { - "i2s", "pcm", -}; -static const char *mt7988_led_groups[] = { - "gbe0_led1", "gbe1_led1", "gbe2_led1", "gbe3_led1", "2p5gbe_led1", - "gbe0_led0", "gbe1_led0", "gbe2_led0", "gbe3_led0", "2p5gbe_led0", - "wf5g_led0", "wf5g_led1", -}; -static const char *mt7988_usb_groups[] = { - "drv_vbus", - "drv_vbus_p1", -}; - -static const struct function_desc mt7988_functions[] = { - { "audio", mt7988_audio_groups, ARRAY_SIZE(mt7988_audio_groups) }, - { "jtag", mt7988_jtag_groups, ARRAY_SIZE(mt7988_jtag_groups) }, - { "int_usxgmii", mt7988_int_usxgmii_groups, - ARRAY_SIZE(mt7988_int_usxgmii_groups) }, - { "pwm", mt7988_pwm_groups, ARRAY_SIZE(mt7988_pwm_groups) }, - { "dfd", mt7988_dfd_groups, ARRAY_SIZE(mt7988_dfd_groups) }, - { "i2c", mt7988_i2c_groups, ARRAY_SIZE(mt7988_i2c_groups) }, - { "eth", mt7988_ethernet_groups, ARRAY_SIZE(mt7988_ethernet_groups) }, - { "pcie", mt7988_pcie_groups, ARRAY_SIZE(mt7988_pcie_groups) }, - { "pmic", mt7988_pmic_groups, ARRAY_SIZE(mt7988_pmic_groups) }, - { "watchdog", mt7988_wdt_groups, ARRAY_SIZE(mt7988_wdt_groups) }, - { "spi", mt7988_spi_groups, ARRAY_SIZE(mt7988_spi_groups) }, - { "flash", mt7988_flash_groups, ARRAY_SIZE(mt7988_flash_groups) }, - { "uart", mt7988_uart_groups, ARRAY_SIZE(mt7988_uart_groups) }, - { "udi", mt7988_udi_groups, ARRAY_SIZE(mt7988_udi_groups) }, - { "usb", mt7988_usb_groups, ARRAY_SIZE(mt7988_usb_groups) }, - { "led", mt7988_led_groups, ARRAY_SIZE(mt7988_led_groups) }, -}; - -static const struct mtk_eint_hw mt7988_eint_hw = { - .port_mask = 7, - .ports = 7, - .ap_num = ARRAY_SIZE(mt7988_pins), - .db_cnt = 16, -}; - -static const char *mt7988_pinctrl_register_base_names[] = { - "gpio_base", "iocfg_tr_base", "iocfg_br_base", - "iocfg_rb_base", "iocfg_lb_base", "iocfg_tl_base", -}; - -static struct mtk_pin_soc mt7988_data = { - .reg_cal = mt7988_reg_cals, - .pins = mt7988_pins, - .npins = ARRAY_SIZE(mt7988_pins), - .grps = mt7988_groups, - .ngrps = ARRAY_SIZE(mt7988_groups), - .funcs = mt7988_functions, - .nfuncs = ARRAY_SIZE(mt7988_functions), - .eint_hw = &mt7988_eint_hw, - .gpio_m = 0, - .ies_present = false, - .base_names = mt7988_pinctrl_register_base_names, - .nbase_names = ARRAY_SIZE(mt7988_pinctrl_register_base_names), - .bias_disable_set = mtk_pinconf_bias_disable_set, - .bias_disable_get = mtk_pinconf_bias_disable_get, - .bias_set = mtk_pinconf_bias_set, - .bias_get = mtk_pinconf_bias_get, - .drive_set = mtk_pinconf_drive_set_rev1, - .drive_get = mtk_pinconf_drive_get_rev1, - .adv_pull_get = mtk_pinconf_adv_pull_get, - .adv_pull_set = mtk_pinconf_adv_pull_set, -}; - -static const struct of_device_id mt7988_pinctrl_of_match[] = { - { - .compatible = "mediatek,mt7988-pinctrl", - }, - {} -}; - -static int mt7988_pinctrl_probe(struct platform_device *pdev) -{ - return mtk_moore_pinctrl_probe(pdev, &mt7988_data); -} - -static struct platform_driver mt7988_pinctrl_driver = { - .driver = { - .name = "mt7988-pinctrl", - .of_match_table = mt7988_pinctrl_of_match, - }, - .probe = mt7988_pinctrl_probe, -}; - -static int __init mt7988_pinctrl_init(void) -{ - return platform_driver_register(&mt7988_pinctrl_driver); -} -arch_initcall(mt7988_pinctrl_init); diff --git a/target/linux/mediatek/files-5.15/include/dt-bindings/clock/mediatek,mt7981-clk.h b/target/linux/mediatek/files-5.15/include/dt-bindings/clock/mediatek,mt7981-clk.h deleted file mode 100644 index 192f8cefb5..0000000000 --- a/target/linux/mediatek/files-5.15/include/dt-bindings/clock/mediatek,mt7981-clk.h +++ /dev/null @@ -1,215 +0,0 @@ -/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ -/* - * Copyright (c) 2021 MediaTek Inc. - * Author: Wenzhen.Yu - * Author: Jianhui Zhao - * Author: Daniel Golle - */ - -#ifndef _DT_BINDINGS_CLK_MT7981_H -#define _DT_BINDINGS_CLK_MT7981_H - -/* TOPCKGEN */ -#define CLK_TOP_CB_CKSQ_40M 0 -#define CLK_TOP_CB_M_416M 1 -#define CLK_TOP_CB_M_D2 2 -#define CLK_TOP_CB_M_D3 3 -#define CLK_TOP_M_D3_D2 4 -#define CLK_TOP_CB_M_D4 5 -#define CLK_TOP_CB_M_D8 6 -#define CLK_TOP_M_D8_D2 7 -#define CLK_TOP_CB_MM_720M 8 -#define CLK_TOP_CB_MM_D2 9 -#define CLK_TOP_CB_MM_D3 10 -#define CLK_TOP_CB_MM_D3_D5 11 -#define CLK_TOP_CB_MM_D4 12 -#define CLK_TOP_CB_MM_D6 13 -#define CLK_TOP_MM_D6_D2 14 -#define CLK_TOP_CB_MM_D8 15 -#define CLK_TOP_CB_APLL2_196M 16 -#define CLK_TOP_APLL2_D2 17 -#define CLK_TOP_APLL2_D4 18 -#define CLK_TOP_NET1_2500M 19 -#define CLK_TOP_CB_NET1_D4 20 -#define CLK_TOP_CB_NET1_D5 21 -#define CLK_TOP_NET1_D5_D2 22 -#define CLK_TOP_NET1_D5_D4 23 -#define CLK_TOP_CB_NET1_D8 24 -#define CLK_TOP_NET1_D8_D2 25 -#define CLK_TOP_NET1_D8_D4 26 -#define CLK_TOP_CB_NET2_800M 27 -#define CLK_TOP_CB_NET2_D2 28 -#define CLK_TOP_CB_NET2_D4 29 -#define CLK_TOP_NET2_D4_D2 30 -#define CLK_TOP_NET2_D4_D4 31 -#define CLK_TOP_CB_NET2_D6 32 -#define CLK_TOP_CB_WEDMCU_208M 33 -#define CLK_TOP_CB_SGM_325M 34 -#define CLK_TOP_CKSQ_40M_D2 35 -#define CLK_TOP_CB_RTC_32K 36 -#define CLK_TOP_CB_RTC_32P7K 37 -#define CLK_TOP_USB_TX250M 38 -#define CLK_TOP_FAUD 39 -#define CLK_TOP_NFI1X 40 -#define CLK_TOP_USB_EQ_RX250M 41 -#define CLK_TOP_USB_CDR_CK 42 -#define CLK_TOP_USB_LN0_CK 43 -#define CLK_TOP_SPINFI_BCK 44 -#define CLK_TOP_SPI 45 -#define CLK_TOP_SPIM_MST 46 -#define CLK_TOP_UART_BCK 47 -#define CLK_TOP_PWM_BCK 48 -#define CLK_TOP_I2C_BCK 49 -#define CLK_TOP_PEXTP_TL 50 -#define CLK_TOP_EMMC_208M 51 -#define CLK_TOP_EMMC_400M 52 -#define CLK_TOP_DRAMC_REF 53 -#define CLK_TOP_DRAMC_MD32 54 -#define CLK_TOP_SYSAXI 55 -#define CLK_TOP_SYSAPB 56 -#define CLK_TOP_ARM_DB_MAIN 57 -#define CLK_TOP_AP2CNN_HOST 58 -#define CLK_TOP_NETSYS 59 -#define CLK_TOP_NETSYS_500M 60 -#define CLK_TOP_NETSYS_WED_MCU 61 -#define CLK_TOP_NETSYS_2X 62 -#define CLK_TOP_SGM_325M 63 -#define CLK_TOP_SGM_REG 64 -#define CLK_TOP_F26M 65 -#define CLK_TOP_EIP97B 66 -#define CLK_TOP_USB3_PHY 67 -#define CLK_TOP_AUD 68 -#define CLK_TOP_A1SYS 69 -#define CLK_TOP_AUD_L 70 -#define CLK_TOP_A_TUNER 71 -#define CLK_TOP_U2U3_REF 72 -#define CLK_TOP_U2U3_SYS 73 -#define CLK_TOP_U2U3_XHCI 74 -#define CLK_TOP_USB_FRMCNT 75 -#define CLK_TOP_NFI1X_SEL 76 -#define CLK_TOP_SPINFI_SEL 77 -#define CLK_TOP_SPI_SEL 78 -#define CLK_TOP_SPIM_MST_SEL 79 -#define CLK_TOP_UART_SEL 80 -#define CLK_TOP_PWM_SEL 81 -#define CLK_TOP_I2C_SEL 82 -#define CLK_TOP_PEXTP_TL_SEL 83 -#define CLK_TOP_EMMC_208M_SEL 84 -#define CLK_TOP_EMMC_400M_SEL 85 -#define CLK_TOP_F26M_SEL 86 -#define CLK_TOP_DRAMC_SEL 87 -#define CLK_TOP_DRAMC_MD32_SEL 88 -#define CLK_TOP_SYSAXI_SEL 89 -#define CLK_TOP_SYSAPB_SEL 90 -#define CLK_TOP_ARM_DB_MAIN_SEL 91 -#define CLK_TOP_AP2CNN_HOST_SEL 92 -#define CLK_TOP_NETSYS_SEL 93 -#define CLK_TOP_NETSYS_500M_SEL 94 -#define CLK_TOP_NETSYS_MCU_SEL 95 -#define CLK_TOP_NETSYS_2X_SEL 96 -#define CLK_TOP_SGM_325M_SEL 97 -#define CLK_TOP_SGM_REG_SEL 98 -#define CLK_TOP_EIP97B_SEL 99 -#define CLK_TOP_USB3_PHY_SEL 100 -#define CLK_TOP_AUD_SEL 101 -#define CLK_TOP_A1SYS_SEL 102 -#define CLK_TOP_AUD_L_SEL 103 -#define CLK_TOP_A_TUNER_SEL 104 -#define CLK_TOP_U2U3_SEL 105 -#define CLK_TOP_U2U3_SYS_SEL 106 -#define CLK_TOP_U2U3_XHCI_SEL 107 -#define CLK_TOP_USB_FRMCNT_SEL 108 -#define CLK_TOP_AUD_I2S_M 109 - -/* INFRACFG */ -#define CLK_INFRA_66M_MCK 0 -#define CLK_INFRA_UART0_SEL 1 -#define CLK_INFRA_UART1_SEL 2 -#define CLK_INFRA_UART2_SEL 3 -#define CLK_INFRA_SPI0_SEL 4 -#define CLK_INFRA_SPI1_SEL 5 -#define CLK_INFRA_SPI2_SEL 6 -#define CLK_INFRA_PWM1_SEL 7 -#define CLK_INFRA_PWM2_SEL 8 -#define CLK_INFRA_PWM3_SEL 9 -#define CLK_INFRA_PWM_BSEL 10 -#define CLK_INFRA_PCIE_SEL 11 -#define CLK_INFRA_GPT_STA 12 -#define CLK_INFRA_PWM_HCK 13 -#define CLK_INFRA_PWM_STA 14 -#define CLK_INFRA_PWM1_CK 15 -#define CLK_INFRA_PWM2_CK 16 -#define CLK_INFRA_PWM3_CK 17 -#define CLK_INFRA_CQ_DMA_CK 18 -#define CLK_INFRA_AUD_BUS_CK 19 -#define CLK_INFRA_AUD_26M_CK 20 -#define CLK_INFRA_AUD_L_CK 21 -#define CLK_INFRA_AUD_AUD_CK 22 -#define CLK_INFRA_AUD_EG2_CK 23 -#define CLK_INFRA_DRAMC_26M_CK 24 -#define CLK_INFRA_DBG_CK 25 -#define CLK_INFRA_AP_DMA_CK 26 -#define CLK_INFRA_SEJ_CK 27 -#define CLK_INFRA_SEJ_13M_CK 28 -#define CLK_INFRA_THERM_CK 29 -#define CLK_INFRA_I2C0_CK 30 -#define CLK_INFRA_UART0_CK 31 -#define CLK_INFRA_UART1_CK 32 -#define CLK_INFRA_UART2_CK 33 -#define CLK_INFRA_SPI2_CK 34 -#define CLK_INFRA_SPI2_HCK_CK 35 -#define CLK_INFRA_NFI1_CK 36 -#define CLK_INFRA_SPINFI1_CK 37 -#define CLK_INFRA_NFI_HCK_CK 38 -#define CLK_INFRA_SPI0_CK 39 -#define CLK_INFRA_SPI1_CK 40 -#define CLK_INFRA_SPI0_HCK_CK 41 -#define CLK_INFRA_SPI1_HCK_CK 42 -#define CLK_INFRA_FRTC_CK 43 -#define CLK_INFRA_MSDC_CK 44 -#define CLK_INFRA_MSDC_HCK_CK 45 -#define CLK_INFRA_MSDC_133M_CK 46 -#define CLK_INFRA_MSDC_66M_CK 47 -#define CLK_INFRA_ADC_26M_CK 48 -#define CLK_INFRA_ADC_FRC_CK 49 -#define CLK_INFRA_FBIST2FPC_CK 50 -#define CLK_INFRA_I2C_MCK_CK 51 -#define CLK_INFRA_I2C_PCK_CK 52 -#define CLK_INFRA_IUSB_133_CK 53 -#define CLK_INFRA_IUSB_66M_CK 54 -#define CLK_INFRA_IUSB_SYS_CK 55 -#define CLK_INFRA_IUSB_CK 56 -#define CLK_INFRA_IPCIE_CK 57 -#define CLK_INFRA_IPCIE_PIPE_CK 58 -#define CLK_INFRA_IPCIER_CK 59 -#define CLK_INFRA_IPCIEB_CK 60 - -/* APMIXEDSYS */ -#define CLK_APMIXED_ARMPLL 0 -#define CLK_APMIXED_NET2PLL 1 -#define CLK_APMIXED_MMPLL 2 -#define CLK_APMIXED_SGMPLL 3 -#define CLK_APMIXED_WEDMCUPLL 4 -#define CLK_APMIXED_NET1PLL 5 -#define CLK_APMIXED_MPLL 6 -#define CLK_APMIXED_APLL2 7 - -/* SGMIISYS_0 */ -#define CLK_SGM0_TX_EN 0 -#define CLK_SGM0_RX_EN 1 -#define CLK_SGM0_CK0_EN 2 -#define CLK_SGM0_CDR_CK0_EN 3 - -/* SGMIISYS_1 */ -#define CLK_SGM1_TX_EN 0 -#define CLK_SGM1_RX_EN 1 -#define CLK_SGM1_CK1_EN 2 -#define CLK_SGM1_CDR_CK1_EN 3 - -/* ETHSYS */ -#define CLK_ETH_FE_EN 0 -#define CLK_ETH_GP2_EN 1 -#define CLK_ETH_GP1_EN 2 -#define CLK_ETH_WOCPU0_EN 3 - -#endif /* _DT_BINDINGS_CLK_MT7981_H */ diff --git a/target/linux/mediatek/files-5.15/include/dt-bindings/clock/mediatek,mt7988-clk.h b/target/linux/mediatek/files-5.15/include/dt-bindings/clock/mediatek,mt7988-clk.h deleted file mode 100644 index 77cfea4a8e..0000000000 --- a/target/linux/mediatek/files-5.15/include/dt-bindings/clock/mediatek,mt7988-clk.h +++ /dev/null @@ -1,276 +0,0 @@ -/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ -/* - * Copyright (c) 2023 MediaTek Inc. - * Author: Sam Shih - * Author: Xiufeng Li - */ - -#ifndef _DT_BINDINGS_CLK_MT7988_H -#define _DT_BINDINGS_CLK_MT7988_H - -/* APMIXEDSYS */ - -#define CLK_APMIXED_NETSYSPLL 0 -#define CLK_APMIXED_MPLL 1 -#define CLK_APMIXED_MMPLL 2 -#define CLK_APMIXED_APLL2 3 -#define CLK_APMIXED_NET1PLL 4 -#define CLK_APMIXED_NET2PLL 5 -#define CLK_APMIXED_WEDMCUPLL 6 -#define CLK_APMIXED_SGMPLL 7 -#define CLK_APMIXED_ARM_B 8 -#define CLK_APMIXED_CCIPLL2_B 9 -#define CLK_APMIXED_USXGMIIPLL 10 -#define CLK_APMIXED_MSDCPLL 11 - -/* TOPCKGEN */ - -#define CLK_TOP_XTAL 0 -#define CLK_TOP_XTAL_D2 1 -#define CLK_TOP_RTC_32K 2 -#define CLK_TOP_RTC_32P7K 3 -#define CLK_TOP_MPLL_D2 4 -#define CLK_TOP_MPLL_D3_D2 5 -#define CLK_TOP_MPLL_D4 6 -#define CLK_TOP_MPLL_D8 7 -#define CLK_TOP_MPLL_D8_D2 8 -#define CLK_TOP_MMPLL_D2 9 -#define CLK_TOP_MMPLL_D3_D5 10 -#define CLK_TOP_MMPLL_D4 11 -#define CLK_TOP_MMPLL_D6_D2 12 -#define CLK_TOP_MMPLL_D8 13 -#define CLK_TOP_APLL2_D4 14 -#define CLK_TOP_NET1PLL_D4 15 -#define CLK_TOP_NET1PLL_D5 16 -#define CLK_TOP_NET1PLL_D5_D2 17 -#define CLK_TOP_NET1PLL_D5_D4 18 -#define CLK_TOP_NET1PLL_D8 19 -#define CLK_TOP_NET1PLL_D8_D2 20 -#define CLK_TOP_NET1PLL_D8_D4 21 -#define CLK_TOP_NET1PLL_D8_D8 22 -#define CLK_TOP_NET1PLL_D8_D16 23 -#define CLK_TOP_NET2PLL_D2 24 -#define CLK_TOP_NET2PLL_D4 25 -#define CLK_TOP_NET2PLL_D4_D4 26 -#define CLK_TOP_NET2PLL_D4_D8 27 -#define CLK_TOP_NET2PLL_D6 28 -#define CLK_TOP_NET2PLL_D8 29 -#define CLK_TOP_NETSYS_SEL 30 -#define CLK_TOP_NETSYS_500M_SEL 31 -#define CLK_TOP_NETSYS_2X_SEL 32 -#define CLK_TOP_NETSYS_GSW_SEL 33 -#define CLK_TOP_ETH_GMII_SEL 34 -#define CLK_TOP_NETSYS_MCU_SEL 35 -#define CLK_TOP_NETSYS_PAO_2X_SEL 36 -#define CLK_TOP_EIP197_SEL 37 -#define CLK_TOP_AXI_INFRA_SEL 38 -#define CLK_TOP_UART_SEL 39 -#define CLK_TOP_EMMC_250M_SEL 40 -#define CLK_TOP_EMMC_400M_SEL 41 -#define CLK_TOP_SPI_SEL 42 -#define CLK_TOP_SPIM_MST_SEL 43 -#define CLK_TOP_NFI1X_SEL 44 -#define CLK_TOP_SPINFI_SEL 45 -#define CLK_TOP_PWM_SEL 46 -#define CLK_TOP_I2C_SEL 47 -#define CLK_TOP_PCIE_MBIST_250M_SEL 48 -#define CLK_TOP_PEXTP_TL_SEL 49 -#define CLK_TOP_PEXTP_TL_P1_SEL 50 -#define CLK_TOP_PEXTP_TL_P2_SEL 51 -#define CLK_TOP_PEXTP_TL_P3_SEL 52 -#define CLK_TOP_USB_SYS_SEL 53 -#define CLK_TOP_USB_SYS_P1_SEL 54 -#define CLK_TOP_USB_XHCI_SEL 55 -#define CLK_TOP_USB_XHCI_P1_SEL 56 -#define CLK_TOP_USB_FRMCNT_SEL 57 -#define CLK_TOP_USB_FRMCNT_P1_SEL 58 -#define CLK_TOP_AUD_SEL 59 -#define CLK_TOP_A1SYS_SEL 60 -#define CLK_TOP_AUD_L_SEL 61 -#define CLK_TOP_A_TUNER_SEL 62 -#define CLK_TOP_SSPXTP_SEL 63 -#define CLK_TOP_USB_PHY_SEL 64 -#define CLK_TOP_USXGMII_SBUS_0_SEL 65 -#define CLK_TOP_USXGMII_SBUS_1_SEL 66 -#define CLK_TOP_SGM_0_SEL 67 -#define CLK_TOP_SGM_SBUS_0_SEL 68 -#define CLK_TOP_SGM_1_SEL 69 -#define CLK_TOP_SGM_SBUS_1_SEL 70 -#define CLK_TOP_XFI_PHY_0_XTAL_SEL 71 -#define CLK_TOP_XFI_PHY_1_XTAL_SEL 72 -#define CLK_TOP_SYSAXI_SEL 73 -#define CLK_TOP_SYSAPB_SEL 74 -#define CLK_TOP_ETH_REFCK_50M_SEL 75 -#define CLK_TOP_ETH_SYS_200M_SEL 76 -#define CLK_TOP_ETH_SYS_SEL 77 -#define CLK_TOP_ETH_XGMII_SEL 78 -#define CLK_TOP_BUS_TOPS_SEL 79 -#define CLK_TOP_NPU_TOPS_SEL 80 -#define CLK_TOP_DRAMC_SEL 81 -#define CLK_TOP_DRAMC_MD32_SEL 82 -#define CLK_TOP_INFRA_F26M_SEL 83 -#define CLK_TOP_PEXTP_P0_SEL 84 -#define CLK_TOP_PEXTP_P1_SEL 85 -#define CLK_TOP_PEXTP_P2_SEL 86 -#define CLK_TOP_PEXTP_P3_SEL 87 -#define CLK_TOP_DA_XTP_GLB_P0_SEL 88 -#define CLK_TOP_DA_XTP_GLB_P1_SEL 89 -#define CLK_TOP_DA_XTP_GLB_P2_SEL 90 -#define CLK_TOP_DA_XTP_GLB_P3_SEL 91 -#define CLK_TOP_CKM_SEL 92 -#define CLK_TOP_DA_SEL 93 -#define CLK_TOP_PEXTP_SEL 94 -#define CLK_TOP_TOPS_P2_26M_SEL 95 -#define CLK_TOP_MCUSYS_BACKUP_625M_SEL 96 -#define CLK_TOP_NETSYS_SYNC_250M_SEL 97 -#define CLK_TOP_MACSEC_SEL 98 -#define CLK_TOP_NETSYS_TOPS_400M_SEL 99 -#define CLK_TOP_NETSYS_PPEFB_250M_SEL 100 -#define CLK_TOP_NETSYS_WARP_SEL 101 -#define CLK_TOP_ETH_MII_SEL 102 -#define CLK_TOP_NPU_SEL 103 -#define CLK_TOP_AUD_I2S_M 104 - -/* MCUSYS */ - -#define CLK_MCU_BUS_DIV_SEL 0 -#define CLK_MCU_ARM_DIV_SEL 1 - -/* INFRACFG_AO */ - -#define CLK_INFRA_MUX_UART0_SEL 0 -#define CLK_INFRA_MUX_UART1_SEL 1 -#define CLK_INFRA_MUX_UART2_SEL 2 -#define CLK_INFRA_MUX_SPI0_SEL 3 -#define CLK_INFRA_MUX_SPI1_SEL 4 -#define CLK_INFRA_MUX_SPI2_SEL 5 -#define CLK_INFRA_PWM_SEL 6 -#define CLK_INFRA_PWM_CK1_SEL 7 -#define CLK_INFRA_PWM_CK2_SEL 8 -#define CLK_INFRA_PWM_CK3_SEL 9 -#define CLK_INFRA_PWM_CK4_SEL 10 -#define CLK_INFRA_PWM_CK5_SEL 11 -#define CLK_INFRA_PWM_CK6_SEL 12 -#define CLK_INFRA_PWM_CK7_SEL 13 -#define CLK_INFRA_PWM_CK8_SEL 14 -#define CLK_INFRA_PCIE_GFMUX_TL_O_P0_SEL 15 -#define CLK_INFRA_PCIE_GFMUX_TL_O_P1_SEL 16 -#define CLK_INFRA_PCIE_GFMUX_TL_O_P2_SEL 17 -#define CLK_INFRA_PCIE_GFMUX_TL_O_P3_SEL 18 - -/* INFRACFG */ - -#define CLK_INFRA_PCIE_PERI_26M_CK_P0 19 -#define CLK_INFRA_PCIE_PERI_26M_CK_P1 20 -#define CLK_INFRA_PCIE_PERI_26M_CK_P2 21 -#define CLK_INFRA_PCIE_PERI_26M_CK_P3 22 -#define CLK_INFRA_66M_GPT_BCK 23 -#define CLK_INFRA_66M_PWM_HCK 24 -#define CLK_INFRA_66M_PWM_BCK 25 -#define CLK_INFRA_66M_PWM_CK1 26 -#define CLK_INFRA_66M_PWM_CK2 27 -#define CLK_INFRA_66M_PWM_CK3 28 -#define CLK_INFRA_66M_PWM_CK4 29 -#define CLK_INFRA_66M_PWM_CK5 30 -#define CLK_INFRA_66M_PWM_CK6 31 -#define CLK_INFRA_66M_PWM_CK7 32 -#define CLK_INFRA_66M_PWM_CK8 33 -#define CLK_INFRA_133M_CQDMA_BCK 34 -#define CLK_INFRA_66M_AUD_SLV_BCK 35 -#define CLK_INFRA_AUD_26M 36 -#define CLK_INFRA_AUD_L 37 -#define CLK_INFRA_AUD_AUD 38 -#define CLK_INFRA_AUD_EG2 39 -#define CLK_INFRA_DRAMC_F26M 40 -#define CLK_INFRA_133M_DBG_ACKM 41 -#define CLK_INFRA_66M_AP_DMA_BCK 42 -#define CLK_INFRA_66M_SEJ_BCK 43 -#define CLK_INFRA_PRE_CK_SEJ_F13M 44 -#define CLK_INFRA_26M_THERM_SYSTEM 45 -#define CLK_INFRA_I2C_BCK 46 -#define CLK_INFRA_52M_UART0_CK 47 -#define CLK_INFRA_52M_UART1_CK 48 -#define CLK_INFRA_52M_UART2_CK 49 -#define CLK_INFRA_NFI 50 -#define CLK_INFRA_SPINFI 51 -#define CLK_INFRA_66M_NFI_HCK 52 -#define CLK_INFRA_104M_SPI0 53 -#define CLK_INFRA_104M_SPI1 54 -#define CLK_INFRA_104M_SPI2_BCK 55 -#define CLK_INFRA_66M_SPI0_HCK 56 -#define CLK_INFRA_66M_SPI1_HCK 57 -#define CLK_INFRA_66M_SPI2_HCK 58 -#define CLK_INFRA_66M_FLASHIF_AXI 59 -#define CLK_INFRA_RTC 60 -#define CLK_INFRA_26M_ADC_BCK 61 -#define CLK_INFRA_RC_ADC 62 -#define CLK_INFRA_MSDC400 63 -#define CLK_INFRA_MSDC2_HCK 64 -#define CLK_INFRA_133M_MSDC_0_HCK 65 -#define CLK_INFRA_66M_MSDC_0_HCK 66 -#define CLK_INFRA_133M_CPUM_BCK 67 -#define CLK_INFRA_BIST2FPC 68 -#define CLK_INFRA_I2C_X16W_MCK_CK_P1 69 -#define CLK_INFRA_I2C_X16W_PCK_CK_P1 70 -#define CLK_INFRA_133M_USB_HCK 71 -#define CLK_INFRA_133M_USB_HCK_CK_P1 72 -#define CLK_INFRA_66M_USB_HCK 73 -#define CLK_INFRA_66M_USB_HCK_CK_P1 74 -#define CLK_INFRA_USB_SYS 75 -#define CLK_INFRA_USB_SYS_CK_P1 76 -#define CLK_INFRA_USB_REF 77 -#define CLK_INFRA_USB_CK_P1 78 -#define CLK_INFRA_USB_FRMCNT 79 -#define CLK_INFRA_USB_FRMCNT_CK_P1 80 -#define CLK_INFRA_USB_PIPE 81 -#define CLK_INFRA_USB_PIPE_CK_P1 82 -#define CLK_INFRA_USB_UTMI 83 -#define CLK_INFRA_USB_UTMI_CK_P1 84 -#define CLK_INFRA_USB_XHCI 85 -#define CLK_INFRA_USB_XHCI_CK_P1 86 -#define CLK_INFRA_PCIE_GFMUX_TL_P0 87 -#define CLK_INFRA_PCIE_GFMUX_TL_P1 88 -#define CLK_INFRA_PCIE_GFMUX_TL_P2 89 -#define CLK_INFRA_PCIE_GFMUX_TL_P3 90 -#define CLK_INFRA_PCIE_PIPE_P0 91 -#define CLK_INFRA_PCIE_PIPE_P1 92 -#define CLK_INFRA_PCIE_PIPE_P2 93 -#define CLK_INFRA_PCIE_PIPE_P3 94 -#define CLK_INFRA_133M_PCIE_CK_P0 95 -#define CLK_INFRA_133M_PCIE_CK_P1 96 -#define CLK_INFRA_133M_PCIE_CK_P2 97 -#define CLK_INFRA_133M_PCIE_CK_P3 98 - -/* ETHDMA */ - -#define CLK_ETHDMA_XGP1_EN 0 -#define CLK_ETHDMA_XGP2_EN 1 -#define CLK_ETHDMA_XGP3_EN 2 -#define CLK_ETHDMA_FE_EN 3 -#define CLK_ETHDMA_GP2_EN 4 -#define CLK_ETHDMA_GP1_EN 5 -#define CLK_ETHDMA_GP3_EN 6 -#define CLK_ETHDMA_ESW_EN 7 -#define CLK_ETHDMA_CRYPT0_EN 8 -#define CLK_ETHDMA_NR_CLK 9 - -/* SGMIISYS_0 */ - -#define CLK_SGM0_TX_EN 0 -#define CLK_SGM0_RX_EN 1 -#define CLK_SGMII0_NR_CLK 2 - -/* SGMIISYS_1 */ - -#define CLK_SGM1_TX_EN 0 -#define CLK_SGM1_RX_EN 1 -#define CLK_SGMII1_NR_CLK 2 - -/* ETHWARP */ - -#define CLK_ETHWARP_WOCPU2_EN 0 -#define CLK_ETHWARP_WOCPU1_EN 1 -#define CLK_ETHWARP_WOCPU0_EN 2 -#define CLK_ETHWARP_NR_CLK 3 - -#endif /* _DT_BINDINGS_CLK_MT7988_H */ diff --git a/target/linux/mediatek/files-5.15/include/dt-bindings/clock/mt7986-clk.h b/target/linux/mediatek/files-5.15/include/dt-bindings/clock/mt7986-clk.h deleted file mode 100644 index 5a9b169324..0000000000 --- a/target/linux/mediatek/files-5.15/include/dt-bindings/clock/mt7986-clk.h +++ /dev/null @@ -1,169 +0,0 @@ -/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ -/* - * Copyright (c) 2021 MediaTek Inc. - * Author: Sam Shih - */ - -#ifndef _DT_BINDINGS_CLK_MT7986_H -#define _DT_BINDINGS_CLK_MT7986_H - -/* APMIXEDSYS */ - -#define CLK_APMIXED_ARMPLL 0 -#define CLK_APMIXED_NET2PLL 1 -#define CLK_APMIXED_MMPLL 2 -#define CLK_APMIXED_SGMPLL 3 -#define CLK_APMIXED_WEDMCUPLL 4 -#define CLK_APMIXED_NET1PLL 5 -#define CLK_APMIXED_MPLL 6 -#define CLK_APMIXED_APLL2 7 - -/* TOPCKGEN */ - -#define CLK_TOP_XTAL 0 -#define CLK_TOP_XTAL_D2 1 -#define CLK_TOP_RTC_32K 2 -#define CLK_TOP_RTC_32P7K 3 -#define CLK_TOP_MPLL_D2 4 -#define CLK_TOP_MPLL_D4 5 -#define CLK_TOP_MPLL_D8 6 -#define CLK_TOP_MPLL_D8_D2 7 -#define CLK_TOP_MPLL_D3_D2 8 -#define CLK_TOP_MMPLL_D2 9 -#define CLK_TOP_MMPLL_D4 10 -#define CLK_TOP_MMPLL_D8 11 -#define CLK_TOP_MMPLL_D8_D2 12 -#define CLK_TOP_MMPLL_D3_D8 13 -#define CLK_TOP_MMPLL_U2PHY 14 -#define CLK_TOP_APLL2_D4 15 -#define CLK_TOP_NET1PLL_D4 16 -#define CLK_TOP_NET1PLL_D5 17 -#define CLK_TOP_NET1PLL_D5_D2 18 -#define CLK_TOP_NET1PLL_D5_D4 19 -#define CLK_TOP_NET1PLL_D8_D2 20 -#define CLK_TOP_NET1PLL_D8_D4 21 -#define CLK_TOP_NET2PLL_D4 22 -#define CLK_TOP_NET2PLL_D4_D2 23 -#define CLK_TOP_NET2PLL_D3_D2 24 -#define CLK_TOP_WEDMCUPLL_D5_D2 25 -#define CLK_TOP_NFI1X_SEL 26 -#define CLK_TOP_SPINFI_SEL 27 -#define CLK_TOP_SPI_SEL 28 -#define CLK_TOP_SPIM_MST_SEL 29 -#define CLK_TOP_UART_SEL 30 -#define CLK_TOP_PWM_SEL 31 -#define CLK_TOP_I2C_SEL 32 -#define CLK_TOP_PEXTP_TL_SEL 33 -#define CLK_TOP_EMMC_250M_SEL 34 -#define CLK_TOP_EMMC_416M_SEL 35 -#define CLK_TOP_F_26M_ADC_SEL 36 -#define CLK_TOP_DRAMC_SEL 37 -#define CLK_TOP_DRAMC_MD32_SEL 38 -#define CLK_TOP_SYSAXI_SEL 39 -#define CLK_TOP_SYSAPB_SEL 40 -#define CLK_TOP_ARM_DB_MAIN_SEL 41 -#define CLK_TOP_ARM_DB_JTSEL 42 -#define CLK_TOP_NETSYS_SEL 43 -#define CLK_TOP_NETSYS_500M_SEL 44 -#define CLK_TOP_NETSYS_MCU_SEL 45 -#define CLK_TOP_NETSYS_2X_SEL 46 -#define CLK_TOP_SGM_325M_SEL 47 -#define CLK_TOP_SGM_REG_SEL 48 -#define CLK_TOP_A1SYS_SEL 49 -#define CLK_TOP_CONN_MCUSYS_SEL 50 -#define CLK_TOP_EIP_B_SEL 51 -#define CLK_TOP_PCIE_PHY_SEL 52 -#define CLK_TOP_USB3_PHY_SEL 53 -#define CLK_TOP_F26M_SEL 54 -#define CLK_TOP_AUD_L_SEL 55 -#define CLK_TOP_A_TUNER_SEL 56 -#define CLK_TOP_U2U3_SEL 57 -#define CLK_TOP_U2U3_SYS_SEL 58 -#define CLK_TOP_U2U3_XHCI_SEL 59 -#define CLK_TOP_DA_U2_REFSEL 60 -#define CLK_TOP_DA_U2_CK_1P_SEL 61 -#define CLK_TOP_AP2CNN_HOST_SEL 62 -#define CLK_TOP_JTAG 63 - -/* INFRACFG */ - -#define CLK_INFRA_SYSAXI_D2 0 -#define CLK_INFRA_UART0_SEL 1 -#define CLK_INFRA_UART1_SEL 2 -#define CLK_INFRA_UART2_SEL 3 -#define CLK_INFRA_SPI0_SEL 4 -#define CLK_INFRA_SPI1_SEL 5 -#define CLK_INFRA_PWM1_SEL 6 -#define CLK_INFRA_PWM2_SEL 7 -#define CLK_INFRA_PWM_BSEL 8 -#define CLK_INFRA_PCIE_SEL 9 -#define CLK_INFRA_GPT_STA 10 -#define CLK_INFRA_PWM_HCK 11 -#define CLK_INFRA_PWM_STA 12 -#define CLK_INFRA_PWM1_CK 13 -#define CLK_INFRA_PWM2_CK 14 -#define CLK_INFRA_CQ_DMA_CK 15 -#define CLK_INFRA_EIP97_CK 16 -#define CLK_INFRA_AUD_BUS_CK 17 -#define CLK_INFRA_AUD_26M_CK 18 -#define CLK_INFRA_AUD_L_CK 19 -#define CLK_INFRA_AUD_AUD_CK 20 -#define CLK_INFRA_AUD_EG2_CK 21 -#define CLK_INFRA_DRAMC_26M_CK 22 -#define CLK_INFRA_DBG_CK 23 -#define CLK_INFRA_AP_DMA_CK 24 -#define CLK_INFRA_SEJ_CK 25 -#define CLK_INFRA_SEJ_13M_CK 26 -#define CLK_INFRA_THERM_CK 27 -#define CLK_INFRA_I2C0_CK 28 -#define CLK_INFRA_UART0_CK 29 -#define CLK_INFRA_UART1_CK 30 -#define CLK_INFRA_UART2_CK 31 -#define CLK_INFRA_NFI1_CK 32 -#define CLK_INFRA_SPINFI1_CK 33 -#define CLK_INFRA_NFI_HCK_CK 34 -#define CLK_INFRA_SPI0_CK 35 -#define CLK_INFRA_SPI1_CK 36 -#define CLK_INFRA_SPI0_HCK_CK 37 -#define CLK_INFRA_SPI1_HCK_CK 38 -#define CLK_INFRA_FRTC_CK 39 -#define CLK_INFRA_MSDC_CK 40 -#define CLK_INFRA_MSDC_HCK_CK 41 -#define CLK_INFRA_MSDC_133M_CK 42 -#define CLK_INFRA_MSDC_66M_CK 43 -#define CLK_INFRA_ADC_26M_CK 44 -#define CLK_INFRA_ADC_FRC_CK 45 -#define CLK_INFRA_FBIST2FPC_CK 46 -#define CLK_INFRA_IUSB_133_CK 47 -#define CLK_INFRA_IUSB_66M_CK 48 -#define CLK_INFRA_IUSB_SYS_CK 49 -#define CLK_INFRA_IUSB_CK 50 -#define CLK_INFRA_IPCIE_CK 51 -#define CLK_INFRA_IPCIE_PIPE_CK 52 -#define CLK_INFRA_IPCIER_CK 53 -#define CLK_INFRA_IPCIEB_CK 54 -#define CLK_INFRA_TRNG_CK 55 - -/* SGMIISYS_0 */ - -#define CLK_SGMII0_TX250M_EN 0 -#define CLK_SGMII0_RX250M_EN 1 -#define CLK_SGMII0_CDR_REF 2 -#define CLK_SGMII0_CDR_FB 3 - -/* SGMIISYS_1 */ - -#define CLK_SGMII1_TX250M_EN 0 -#define CLK_SGMII1_RX250M_EN 1 -#define CLK_SGMII1_CDR_REF 2 -#define CLK_SGMII1_CDR_FB 3 - -/* ETHSYS */ - -#define CLK_ETH_FE_EN 0 -#define CLK_ETH_GP2_EN 1 -#define CLK_ETH_GP1_EN 2 -#define CLK_ETH_WOCPU1_EN 3 -#define CLK_ETH_WOCPU0_EN 4 - -#endif /* _DT_BINDINGS_CLK_MT7986_H */ diff --git a/target/linux/mediatek/files-5.15/include/dt-bindings/reset/mt7986-resets.h b/target/linux/mediatek/files-5.15/include/dt-bindings/reset/mt7986-resets.h deleted file mode 100644 index af3d16c811..0000000000 --- a/target/linux/mediatek/files-5.15/include/dt-bindings/reset/mt7986-resets.h +++ /dev/null @@ -1,55 +0,0 @@ -/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */ -/* - * Copyright (c) 2022 MediaTek Inc. - * Author: Sam Shih - */ - -#ifndef _DT_BINDINGS_RESET_CONTROLLER_MT7986 -#define _DT_BINDINGS_RESET_CONTROLLER_MT7986 - -/* INFRACFG resets */ -#define MT7986_INFRACFG_PEXTP_MAC_SW_RST 6 -#define MT7986_INFRACFG_SSUSB_SW_RST 7 -#define MT7986_INFRACFG_EIP97_SW_RST 8 -#define MT7986_INFRACFG_AUDIO_SW_RST 13 -#define MT7986_INFRACFG_CQ_DMA_SW_RST 14 - -#define MT7986_INFRACFG_TRNG_SW_RST 17 -#define MT7986_INFRACFG_AP_DMA_SW_RST 32 -#define MT7986_INFRACFG_I2C_SW_RST 33 -#define MT7986_INFRACFG_NFI_SW_RST 34 -#define MT7986_INFRACFG_SPI0_SW_RST 35 -#define MT7986_INFRACFG_SPI1_SW_RST 36 -#define MT7986_INFRACFG_UART0_SW_RST 37 -#define MT7986_INFRACFG_UART1_SW_RST 38 -#define MT7986_INFRACFG_UART2_SW_RST 39 -#define MT7986_INFRACFG_AUXADC_SW_RST 43 - -#define MT7986_INFRACFG_APXGPT_SW_RST 66 -#define MT7986_INFRACFG_PWM_SW_RST 68 - -#define MT7986_INFRACFG_SW_RST_NUM 69 - -/* TOPRGU resets */ -#define MT7986_TOPRGU_APMIXEDSYS_SW_RST 0 -#define MT7986_TOPRGU_SGMII0_SW_RST 1 -#define MT7986_TOPRGU_SGMII1_SW_RST 2 -#define MT7986_TOPRGU_INFRA_SW_RST 3 -#define MT7986_TOPRGU_U2PHY_SW_RST 5 -#define MT7986_TOPRGU_PCIE_SW_RST 6 -#define MT7986_TOPRGU_SSUSB_SW_RST 7 -#define MT7986_TOPRGU_ETHDMA_SW_RST 20 -#define MT7986_TOPRGU_CONSYS_SW_RST 23 - -#define MT7986_TOPRGU_SW_RST_NUM 24 - -/* ETHSYS Subsystem resets */ -#define MT7986_ETHSYS_FE_SW_RST 6 -#define MT7986_ETHSYS_PMTR_SW_RST 8 -#define MT7986_ETHSYS_GMAC_SW_RST 23 -#define MT7986_ETHSYS_PPE0_SW_RST 30 -#define MT7986_ETHSYS_PPE1_SW_RST 31 - -#define MT7986_ETHSYS_SW_RST_NUM 32 - -#endif /* _DT_BINDINGS_RESET_CONTROLLER_MT7986 */ diff --git a/target/linux/mediatek/filogic/config-5.15 b/target/linux/mediatek/filogic/config-5.15 deleted file mode 100644 index 8ba0b0efe8..0000000000 --- a/target/linux/mediatek/filogic/config-5.15 +++ /dev/null @@ -1,443 +0,0 @@ -CONFIG_64BIT=y -# CONFIG_AHCI_MTK is not set -CONFIG_AQUANTIA_PHY=y -CONFIG_ARCH_DMA_ADDR_T_64BIT=y -CONFIG_ARCH_KEEP_MEMBLOCK=y -CONFIG_ARCH_MEDIATEK=y -CONFIG_ARCH_MHP_MEMMAP_ON_MEMORY_ENABLE=y -CONFIG_ARCH_MMAP_RND_BITS=18 -CONFIG_ARCH_MMAP_RND_BITS_MAX=24 -CONFIG_ARCH_MMAP_RND_BITS_MIN=18 -CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MIN=11 -CONFIG_ARCH_PROC_KCORE_TEXT=y -CONFIG_ARCH_SPARSEMEM_ENABLE=y -CONFIG_ARCH_STACKWALK=y -CONFIG_ARCH_SUSPEND_POSSIBLE=y -CONFIG_ARCH_WANTS_NO_INSTR=y -CONFIG_ARM64=y -CONFIG_ARM64_4K_PAGES=y -CONFIG_ARM64_CRYPTO=y -CONFIG_ARM64_ERRATUM_843419=y -CONFIG_ARM64_LD_HAS_FIX_ERRATUM_843419=y -CONFIG_ARM64_PAGE_SHIFT=12 -CONFIG_ARM64_PA_BITS=48 -CONFIG_ARM64_PA_BITS_48=y -CONFIG_ARM64_TAGGED_ADDR_ABI=y -CONFIG_ARM64_VA_BITS=39 -CONFIG_ARM64_VA_BITS_39=y -CONFIG_ARM_AMBA=y -CONFIG_ARM_ARCH_TIMER=y -CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y -CONFIG_ARM_GIC=y -CONFIG_ARM_GIC_V2M=y -CONFIG_ARM_GIC_V3=y -CONFIG_ARM_GIC_V3_ITS=y -CONFIG_ARM_GIC_V3_ITS_PCI=y -CONFIG_ARM_MEDIATEK_CPUFREQ=y -CONFIG_ARM_PMU=y -CONFIG_ARM_PSCI_FW=y -CONFIG_ATA=y -CONFIG_AUDIT_ARCH_COMPAT_GENERIC=y -CONFIG_BLK_DEV_LOOP=y -CONFIG_BLK_DEV_SD=y -CONFIG_BLK_MQ_PCI=y -CONFIG_BLK_PM=y -CONFIG_BSD_PROCESS_ACCT=y -CONFIG_BSD_PROCESS_ACCT_V3=y -CONFIG_CC_HAVE_SHADOW_CALL_STACK=y -CONFIG_CC_HAVE_STACKPROTECTOR_SYSREG=y -CONFIG_CLKSRC_MMIO=y -CONFIG_CLONE_BACKWARDS=y -CONFIG_CMDLINE_OVERRIDE=y -CONFIG_COMMON_CLK=y -CONFIG_COMMON_CLK_MEDIATEK=y -# CONFIG_COMMON_CLK_MT2712 is not set -# CONFIG_COMMON_CLK_MT6779 is not set -# CONFIG_COMMON_CLK_MT6797 is not set -# CONFIG_COMMON_CLK_MT7622 is not set -CONFIG_COMMON_CLK_MT7981=y -CONFIG_COMMON_CLK_MT7981_ETHSYS=y -CONFIG_COMMON_CLK_MT7986=y -CONFIG_COMMON_CLK_MT7986_ETHSYS=y -CONFIG_COMMON_CLK_MT7988=y -# CONFIG_COMMON_CLK_MT8173 is not set -# CONFIG_COMMON_CLK_MT8183 is not set -# CONFIG_COMMON_CLK_MT8516 is not set -# CONFIG_COMPAT_32BIT_TIME is not set -CONFIG_CONFIGFS_FS=y -CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15 -# CONFIG_CPUFREQ_DT is not set -CONFIG_CPU_FREQ=y -# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set -CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y -CONFIG_CPU_FREQ_GOV_ATTR_SET=y -CONFIG_CPU_FREQ_GOV_COMMON=y -CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y -CONFIG_CPU_FREQ_GOV_ONDEMAND=y -CONFIG_CPU_FREQ_GOV_PERFORMANCE=y -CONFIG_CPU_FREQ_GOV_POWERSAVE=y -CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y -CONFIG_CPU_FREQ_GOV_USERSPACE=y -CONFIG_CPU_FREQ_STAT=y -CONFIG_CPU_LITTLE_ENDIAN=y -CONFIG_CPU_RMAP=y -CONFIG_CPU_THERMAL=y -CONFIG_CRC16=y -CONFIG_CRYPTO_AES_ARM64=y -CONFIG_CRYPTO_AES_ARM64_CE=y -CONFIG_CRYPTO_AES_ARM64_CE_BLK=y -CONFIG_CRYPTO_AES_ARM64_CE_CCM=y -CONFIG_CRYPTO_CMAC=y -CONFIG_CRYPTO_CRC32=y -CONFIG_CRYPTO_CRC32C=y -CONFIG_CRYPTO_CRYPTD=y -CONFIG_CRYPTO_DEFLATE=y -CONFIG_CRYPTO_DRBG=y -CONFIG_CRYPTO_DRBG_HMAC=y -CONFIG_CRYPTO_DRBG_MENU=y -CONFIG_CRYPTO_ECB=y -CONFIG_CRYPTO_ECC=y -CONFIG_CRYPTO_ECDH=y -CONFIG_CRYPTO_GHASH_ARM64_CE=y -CONFIG_CRYPTO_HASH_INFO=y -CONFIG_CRYPTO_HMAC=y -CONFIG_CRYPTO_JITTERENTROPY=y -CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC=y -CONFIG_CRYPTO_LIB_SHA256=y -CONFIG_CRYPTO_LZO=y -CONFIG_CRYPTO_RNG=y -CONFIG_CRYPTO_RNG2=y -CONFIG_CRYPTO_RNG_DEFAULT=y -CONFIG_CRYPTO_SHA256=y -CONFIG_CRYPTO_SHA256_ARM64=y -CONFIG_CRYPTO_SHA2_ARM64_CE=y -CONFIG_CRYPTO_SHA512=y -CONFIG_CRYPTO_SIMD=y -CONFIG_CRYPTO_ZSTD=y -CONFIG_DCACHE_WORD_ACCESS=y -CONFIG_DEBUG_MISC=y -CONFIG_DIMLIB=y -CONFIG_DMADEVICES=y -CONFIG_DMATEST=y -CONFIG_DMA_DIRECT_REMAP=y -CONFIG_DMA_ENGINE=y -CONFIG_DMA_ENGINE_RAID=y -CONFIG_DMA_OF=y -CONFIG_DMA_REMAP=y -CONFIG_DMA_VIRTUAL_CHANNELS=y -CONFIG_DTC=y -CONFIG_EDAC_SUPPORT=y -CONFIG_EINT_MTK=y -CONFIG_EXT4_FS=y -CONFIG_F2FS_FS=y -CONFIG_FIT_PARTITION=y -CONFIG_FIXED_PHY=y -CONFIG_FIX_EARLYCON_MEM=y -CONFIG_FRAME_POINTER=y -CONFIG_FS_IOMAP=y -CONFIG_FS_MBCACHE=y -CONFIG_FWNODE_MDIO=y -CONFIG_FW_LOADER_PAGED_BUF=y -CONFIG_GENERIC_ALLOCATOR=y -CONFIG_GENERIC_ARCH_TOPOLOGY=y -CONFIG_GENERIC_BUG=y -CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y -CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y -CONFIG_GENERIC_CPU_AUTOPROBE=y -CONFIG_GENERIC_CPU_VULNERABILITIES=y -CONFIG_GENERIC_CSUM=y -CONFIG_GENERIC_EARLY_IOREMAP=y -CONFIG_GENERIC_FIND_FIRST_BIT=y -CONFIG_GENERIC_GETTIMEOFDAY=y -CONFIG_GENERIC_IDLE_POLL_SETUP=y -CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y -CONFIG_GENERIC_IRQ_SHOW=y -CONFIG_GENERIC_IRQ_SHOW_LEVEL=y -CONFIG_GENERIC_LIB_DEVMEM_IS_ALLOWED=y -CONFIG_GENERIC_MSI_IRQ=y -CONFIG_GENERIC_MSI_IRQ_DOMAIN=y -CONFIG_GENERIC_PCI_IOMAP=y -CONFIG_GENERIC_PHY=y -CONFIG_GENERIC_PINCONF=y -CONFIG_GENERIC_PINCTRL_GROUPS=y -CONFIG_GENERIC_PINMUX_FUNCTIONS=y -CONFIG_GENERIC_SCHED_CLOCK=y -CONFIG_GENERIC_SMP_IDLE_THREAD=y -CONFIG_GENERIC_STRNCPY_FROM_USER=y -CONFIG_GENERIC_STRNLEN_USER=y -CONFIG_GENERIC_TIME_VSYSCALL=y -CONFIG_GLOB=y -CONFIG_GPIO_CDEV=y -CONFIG_GPIO_WATCHDOG=y -CONFIG_GPIO_WATCHDOG_ARCH_INITCALL=y -CONFIG_GRO_CELLS=y -CONFIG_HANDLE_DOMAIN_IRQ=y -CONFIG_HARDIRQS_SW_RESEND=y -CONFIG_HAS_DMA=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT_MAP=y -CONFIG_HWMON=y -CONFIG_HW_RANDOM=y -CONFIG_HW_RANDOM_MTK=y -CONFIG_I2C=y -CONFIG_I2C_BOARDINFO=y -CONFIG_I2C_CHARDEV=y -CONFIG_I2C_MT65XX=y -CONFIG_ICPLUS_PHY=y -CONFIG_ILLEGAL_POINTER_VALUE=0xdead000000000000 -CONFIG_INITRAMFS_SOURCE="" -CONFIG_IRQCHIP=y -CONFIG_IRQ_DOMAIN=y -CONFIG_IRQ_DOMAIN_HIERARCHY=y -CONFIG_IRQ_FORCED_THREADING=y -CONFIG_IRQ_TIME_ACCOUNTING=y -CONFIG_IRQ_WORK=y -CONFIG_JBD2=y -CONFIG_JUMP_LABEL=y -CONFIG_LEDS_SMARTRG_LED=y -CONFIG_LIBFDT=y -CONFIG_LOCK_DEBUGGING_SUPPORT=y -CONFIG_LOCK_SPIN_ON_OWNER=y -CONFIG_LZO_COMPRESS=y -CONFIG_LZO_DECOMPRESS=y -CONFIG_MAGIC_SYSRQ=y -CONFIG_MAXLINEAR_GPHY=y -CONFIG_MDIO_BUS=y -CONFIG_MDIO_DEVICE=y -CONFIG_MDIO_DEVRES=y -CONFIG_MEDIATEK_2P5G_PHY=y -CONFIG_MEDIATEK_GE_PHY=y -CONFIG_MEDIATEK_GE_SOC_PHY=y -CONFIG_MEDIATEK_WATCHDOG=y -CONFIG_MEMFD_CREATE=y -CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7 -CONFIG_MFD_SYSCON=y -CONFIG_MIGRATION=y -CONFIG_MMC=y -CONFIG_MMC_BLOCK=y -CONFIG_MMC_CQHCI=y -CONFIG_MMC_MTK=y -CONFIG_MODULES_TREE_LOOKUP=y -CONFIG_MODULES_USE_ELF_RELA=y -CONFIG_MTD_NAND_CORE=y -CONFIG_MTD_NAND_ECC=y -CONFIG_MTD_NAND_ECC_MEDIATEK=y -CONFIG_MTD_NAND_ECC_SW_HAMMING=y -CONFIG_MTD_NAND_MTK=y -CONFIG_MTD_NAND_MTK_BMT=y -CONFIG_MTD_PARSER_TRX=y -CONFIG_MTD_RAW_NAND=y -CONFIG_MTD_SPI_NAND=y -CONFIG_MTD_SPI_NOR=y -CONFIG_MTD_SPLIT_FIRMWARE=y -CONFIG_MTD_SPLIT_FIT_FW=y -CONFIG_MTD_UBI=y -CONFIG_MTD_UBI_BEB_LIMIT=20 -CONFIG_MTD_UBI_BLOCK=y -CONFIG_MTD_UBI_FASTMAP=y -CONFIG_MTD_UBI_WL_THRESHOLD=4096 -# CONFIG_MTK_CMDQ is not set -# CONFIG_MTK_CQDMA is not set -CONFIG_MTK_HSDMA=y -CONFIG_MTK_INFRACFG=y -CONFIG_MTK_PMIC_WRAP=y -CONFIG_MTK_SCPSYS=y -CONFIG_MTK_SCPSYS_PM_DOMAINS=y -CONFIG_MTK_THERMAL=y -CONFIG_MTK_TIMER=y -# CONFIG_MTK_UART_APDMA is not set -CONFIG_MUTEX_SPIN_ON_OWNER=y -CONFIG_NEED_DMA_MAP_STATE=y -CONFIG_NEED_SG_DMA_LENGTH=y -CONFIG_NET_DEVLINK=y -CONFIG_NET_DSA=y -CONFIG_NET_DSA_MT7530=y -CONFIG_NET_DSA_MT7530_MDIO=y -CONFIG_NET_DSA_MT7530_MMIO=y -CONFIG_NET_DSA_TAG_MTK=y -CONFIG_NET_FLOW_LIMIT=y -CONFIG_NET_MEDIATEK_SOC=y -CONFIG_NET_MEDIATEK_SOC_USXGMII=y -CONFIG_NET_MEDIATEK_SOC_WED=y -CONFIG_NET_SELFTESTS=y -CONFIG_NET_SWITCHDEV=y -CONFIG_NET_VENDOR_MEDIATEK=y -CONFIG_NLS=y -CONFIG_NO_HZ_COMMON=y -CONFIG_NO_HZ_IDLE=y -CONFIG_NR_CPUS=4 -CONFIG_NVMEM=y -CONFIG_NVMEM_LAYOUTS=y -CONFIG_NVMEM_MTK_EFUSE=y -CONFIG_NVMEM_SYSFS=y -CONFIG_OF=y -CONFIG_OF_ADDRESS=y -CONFIG_OF_DYNAMIC=y -CONFIG_OF_EARLY_FLATTREE=y -CONFIG_OF_FLATTREE=y -CONFIG_OF_GPIO=y -CONFIG_OF_IRQ=y -CONFIG_OF_KOBJ=y -CONFIG_OF_MDIO=y -CONFIG_OF_OVERLAY=y -CONFIG_OF_RESOLVE=y -CONFIG_PADATA=y -CONFIG_PAGE_POOL=y -CONFIG_PAGE_POOL_STATS=y -CONFIG_PARTITION_PERCPU=y -CONFIG_PCI=y -CONFIG_PCIEAER=y -CONFIG_PCIEASPM=y -# CONFIG_PCIEASPM_DEFAULT is not set -CONFIG_PCIEASPM_PERFORMANCE=y -# CONFIG_PCIEASPM_POWERSAVE is not set -# CONFIG_PCIEASPM_POWER_SUPERSAVE is not set -CONFIG_PCIEPORTBUS=y -# CONFIG_PCIE_MEDIATEK is not set -CONFIG_PCIE_MEDIATEK_GEN3=y -CONFIG_PCIE_PME=y -CONFIG_PCI_DEBUG=y -CONFIG_PCI_DOMAINS=y -CONFIG_PCI_DOMAINS_GENERIC=y -CONFIG_PCI_MSI=y -CONFIG_PCI_MSI_IRQ_DOMAIN=y -CONFIG_PCS_MTK_LYNXI=y -CONFIG_PERF_EVENTS=y -CONFIG_PGTABLE_LEVELS=3 -CONFIG_PHYLIB=y -CONFIG_PHYLINK=y -CONFIG_PHYS_ADDR_T_64BIT=y -CONFIG_PHY_MTK_TPHY=y -# CONFIG_PHY_MTK_UFS is not set -CONFIG_PHY_MTK_XSPHY=y -CONFIG_PINCTRL=y -# CONFIG_PINCTRL_MT2712 is not set -# CONFIG_PINCTRL_MT6765 is not set -# CONFIG_PINCTRL_MT6797 is not set -# CONFIG_PINCTRL_MT7622 is not set -CONFIG_PINCTRL_MT7981=y -CONFIG_PINCTRL_MT7986=y -CONFIG_PINCTRL_MT7988=y -# CONFIG_PINCTRL_MT8173 is not set -# CONFIG_PINCTRL_MT8183 is not set -CONFIG_PINCTRL_MT8516=y -CONFIG_PINCTRL_MTK=y -CONFIG_PINCTRL_MTK_MOORE=y -CONFIG_PINCTRL_MTK_V2=y -CONFIG_PM=y -CONFIG_PM_CLK=y -CONFIG_PM_GENERIC_DOMAINS=y -CONFIG_PM_GENERIC_DOMAINS_OF=y -CONFIG_PM_OPP=y -CONFIG_POWER_RESET=y -CONFIG_POWER_RESET_SYSCON=y -CONFIG_POWER_SUPPLY=y -CONFIG_PRINTK_TIME=y -CONFIG_PSTORE=y -CONFIG_PSTORE_COMPRESS=y -CONFIG_PSTORE_COMPRESS_DEFAULT="deflate" -CONFIG_PSTORE_CONSOLE=y -CONFIG_PSTORE_DEFLATE_COMPRESS=y -CONFIG_PSTORE_DEFLATE_COMPRESS_DEFAULT=y -CONFIG_PSTORE_PMSG=y -CONFIG_PSTORE_RAM=y -CONFIG_PTP_1588_CLOCK_OPTIONAL=y -CONFIG_PWM=y -CONFIG_PWM_MEDIATEK=y -# CONFIG_PWM_MTK_DISP is not set -CONFIG_PWM_SYSFS=y -CONFIG_QUEUED_RWLOCKS=y -CONFIG_QUEUED_SPINLOCKS=y -CONFIG_RAS=y -CONFIG_RATIONAL=y -# CONFIG_RAVE_SP_CORE is not set -CONFIG_REALTEK_PHY=y -CONFIG_REED_SOLOMON=y -CONFIG_REED_SOLOMON_DEC8=y -CONFIG_REED_SOLOMON_ENC8=y -CONFIG_REGMAP=y -CONFIG_REGMAP_I2C=y -CONFIG_REGMAP_MMIO=y -CONFIG_REGULATOR=y -CONFIG_REGULATOR_FIXED_VOLTAGE=y -CONFIG_REGULATOR_MT6380=y -CONFIG_REGULATOR_RT5190A=y -CONFIG_RESET_CONTROLLER=y -CONFIG_RESET_TI_SYSCON=y -CONFIG_RFS_ACCEL=y -CONFIG_RODATA_FULL_DEFAULT_ENABLED=y -CONFIG_RPS=y -CONFIG_RTC_CLASS=y -CONFIG_RTC_DRV_MT7622=y -CONFIG_RTC_I2C_AND_SPI=y -# CONFIG_RTL8367S_GSW is not set -CONFIG_RWSEM_SPIN_ON_OWNER=y -CONFIG_SCHED_MC=y -CONFIG_SCSI=y -CONFIG_SCSI_COMMON=y -# CONFIG_SECTION_MISMATCH_WARN_ONLY is not set -CONFIG_SERIAL_8250_FSL=y -CONFIG_SERIAL_8250_MT6577=y -CONFIG_SERIAL_8250_NR_UARTS=3 -CONFIG_SERIAL_8250_RUNTIME_UARTS=3 -CONFIG_SERIAL_DEV_BUS=y -CONFIG_SERIAL_DEV_CTRL_TTYPORT=y -CONFIG_SERIAL_MCTRL_GPIO=y -CONFIG_SERIAL_OF_PLATFORM=y -CONFIG_SGL_ALLOC=y -CONFIG_SG_POOL=y -CONFIG_SMP=y -CONFIG_SOCK_RX_QUEUE_MAPPING=y -CONFIG_SPARSEMEM=y -CONFIG_SPARSEMEM_EXTREME=y -CONFIG_SPARSEMEM_VMEMMAP=y -CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y -CONFIG_SPARSE_IRQ=y -CONFIG_SPI=y -CONFIG_SPI_DYNAMIC=y -CONFIG_SPI_MASTER=y -CONFIG_SPI_MEM=y -CONFIG_SPI_MT65XX=y -CONFIG_SPI_MTK_NOR=y -CONFIG_SPI_MTK_SNFI=y -CONFIG_SRCU=y -CONFIG_SWIOTLB=y -CONFIG_SWPHY=y -CONFIG_SYSCTL_EXCEPTION_TRACE=y -CONFIG_THERMAL=y -CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y -CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0 -CONFIG_THERMAL_GOV_BANG_BANG=y -CONFIG_THERMAL_GOV_FAIR_SHARE=y -CONFIG_THERMAL_GOV_STEP_WISE=y -CONFIG_THERMAL_GOV_USER_SPACE=y -CONFIG_THERMAL_HWMON=y -CONFIG_THERMAL_OF=y -CONFIG_THERMAL_WRITABLE_TRIPS=y -CONFIG_THREAD_INFO_IN_TASK=y -CONFIG_TICK_CPU_ACCOUNTING=y -CONFIG_TIMER_OF=y -CONFIG_TIMER_PROBE=y -CONFIG_TRACE_IRQFLAGS_NMI_SUPPORT=y -CONFIG_TREE_RCU=y -CONFIG_TREE_SRCU=y -CONFIG_UBIFS_FS=y -# CONFIG_UCLAMP_TASK is not set -# CONFIG_UNMAP_KERNEL_AT_EL0 is not set -CONFIG_USB_SUPPORT=y -CONFIG_VMAP_STACK=y -CONFIG_WATCHDOG_CORE=y -CONFIG_WATCHDOG_PRETIMEOUT_DEFAULT_GOV_PANIC=y -CONFIG_WATCHDOG_PRETIMEOUT_GOV=y -# CONFIG_WATCHDOG_PRETIMEOUT_GOV_NOOP is not set -CONFIG_WATCHDOG_PRETIMEOUT_GOV_PANIC=y -CONFIG_WATCHDOG_PRETIMEOUT_GOV_SEL=m -CONFIG_WATCHDOG_SYSFS=y -CONFIG_XPS=y -CONFIG_XXHASH=y -CONFIG_ZLIB_DEFLATE=y -CONFIG_ZLIB_INFLATE=y -CONFIG_ZONE_DMA32=y -CONFIG_ZSTD_COMPRESS=y -CONFIG_ZSTD_DECOMPRESS=y diff --git a/target/linux/mediatek/mt7622/config-5.15 b/target/linux/mediatek/mt7622/config-5.15 deleted file mode 100644 index 7bca33c0ae..0000000000 --- a/target/linux/mediatek/mt7622/config-5.15 +++ /dev/null @@ -1,444 +0,0 @@ -CONFIG_64BIT=y -# CONFIG_AHCI_MTK is not set -CONFIG_AQUANTIA_PHY=y -CONFIG_ARCH_DMA_ADDR_T_64BIT=y -CONFIG_ARCH_KEEP_MEMBLOCK=y -CONFIG_ARCH_MEDIATEK=y -CONFIG_ARCH_MHP_MEMMAP_ON_MEMORY_ENABLE=y -CONFIG_ARCH_MMAP_RND_BITS=18 -CONFIG_ARCH_MMAP_RND_BITS_MAX=24 -CONFIG_ARCH_MMAP_RND_BITS_MIN=18 -CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MIN=11 -CONFIG_ARCH_PROC_KCORE_TEXT=y -CONFIG_ARCH_SPARSEMEM_ENABLE=y -CONFIG_ARCH_STACKWALK=y -CONFIG_ARCH_SUSPEND_POSSIBLE=y -CONFIG_ARCH_WANTS_NO_INSTR=y -CONFIG_ARM64=y -CONFIG_ARM64_4K_PAGES=y -CONFIG_ARM64_CRYPTO=y -CONFIG_ARM64_ERRATUM_843419=y -CONFIG_ARM64_LD_HAS_FIX_ERRATUM_843419=y -CONFIG_ARM64_PAGE_SHIFT=12 -CONFIG_ARM64_PA_BITS=48 -CONFIG_ARM64_PA_BITS_48=y -CONFIG_ARM64_TAGGED_ADDR_ABI=y -CONFIG_ARM64_VA_BITS=39 -CONFIG_ARM64_VA_BITS_39=y -CONFIG_ARM_AMBA=y -CONFIG_ARM_ARCH_TIMER=y -CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y -CONFIG_ARM_GIC=y -CONFIG_ARM_GIC_V2M=y -CONFIG_ARM_GIC_V3=y -CONFIG_ARM_GIC_V3_ITS=y -CONFIG_ARM_GIC_V3_ITS_PCI=y -CONFIG_ARM_MEDIATEK_CPUFREQ=y -CONFIG_ARM_PMU=y -CONFIG_ARM_PSCI_FW=y -CONFIG_ATA=y -CONFIG_AUDIT_ARCH_COMPAT_GENERIC=y -CONFIG_BLK_DEV_LOOP=y -CONFIG_BLK_DEV_SD=y -CONFIG_BLK_MQ_PCI=y -CONFIG_BLK_PM=y -CONFIG_BSD_PROCESS_ACCT=y -CONFIG_BSD_PROCESS_ACCT_V3=y -CONFIG_CC_HAVE_SHADOW_CALL_STACK=y -CONFIG_CC_HAVE_STACKPROTECTOR_SYSREG=y -CONFIG_CLKSRC_MMIO=y -CONFIG_CLONE_BACKWARDS=y -# CONFIG_CMDLINE_OVERRIDE is not set -CONFIG_COMMON_CLK=y -CONFIG_COMMON_CLK_MEDIATEK=y -CONFIG_COMMON_CLK_MT2712=y -# CONFIG_COMMON_CLK_MT2712_BDPSYS is not set -# CONFIG_COMMON_CLK_MT2712_IMGSYS is not set -# CONFIG_COMMON_CLK_MT2712_JPGDECSYS is not set -# CONFIG_COMMON_CLK_MT2712_MFGCFG is not set -# CONFIG_COMMON_CLK_MT2712_MMSYS is not set -# CONFIG_COMMON_CLK_MT2712_VDECSYS is not set -# CONFIG_COMMON_CLK_MT2712_VENCSYS is not set -# CONFIG_COMMON_CLK_MT6779 is not set -# CONFIG_COMMON_CLK_MT6797 is not set -CONFIG_COMMON_CLK_MT7622=y -CONFIG_COMMON_CLK_MT7622_AUDSYS=y -CONFIG_COMMON_CLK_MT7622_ETHSYS=y -CONFIG_COMMON_CLK_MT7622_HIFSYS=y -# CONFIG_COMMON_CLK_MT7981 is not set -# CONFIG_COMMON_CLK_MT7986 is not set -# CONFIG_COMMON_CLK_MT7988 is not set -# CONFIG_COMMON_CLK_MT8173 is not set -# CONFIG_COMMON_CLK_MT8183 is not set -# CONFIG_COMMON_CLK_MT8516 is not set -CONFIG_COMPAT_32BIT_TIME=y -CONFIG_CONFIGFS_FS=y -CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15 -# CONFIG_CPUFREQ_DT is not set -CONFIG_CPU_FREQ=y -CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y -# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set -CONFIG_CPU_FREQ_GOV_ATTR_SET=y -CONFIG_CPU_FREQ_GOV_COMMON=y -CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y -CONFIG_CPU_FREQ_GOV_ONDEMAND=y -CONFIG_CPU_FREQ_GOV_PERFORMANCE=y -CONFIG_CPU_FREQ_GOV_POWERSAVE=y -CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y -CONFIG_CPU_FREQ_GOV_USERSPACE=y -CONFIG_CPU_FREQ_STAT=y -CONFIG_CPU_LITTLE_ENDIAN=y -CONFIG_CPU_RMAP=y -CONFIG_CPU_THERMAL=y -CONFIG_CRC16=y -CONFIG_CRYPTO_AES_ARM64=y -CONFIG_CRYPTO_AES_ARM64_CE=y -CONFIG_CRYPTO_AES_ARM64_CE_BLK=y -CONFIG_CRYPTO_AES_ARM64_CE_CCM=y -CONFIG_CRYPTO_CMAC=y -CONFIG_CRYPTO_CRC32=y -CONFIG_CRYPTO_CRC32C=y -CONFIG_CRYPTO_CRYPTD=y -CONFIG_CRYPTO_DEFLATE=y -CONFIG_CRYPTO_DRBG=y -CONFIG_CRYPTO_DRBG_HMAC=y -CONFIG_CRYPTO_DRBG_MENU=y -CONFIG_CRYPTO_ECB=y -CONFIG_CRYPTO_ECC=y -CONFIG_CRYPTO_ECDH=y -CONFIG_CRYPTO_GHASH_ARM64_CE=y -CONFIG_CRYPTO_HASH_INFO=y -CONFIG_CRYPTO_HMAC=y -CONFIG_CRYPTO_JITTERENTROPY=y -CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC=y -CONFIG_CRYPTO_LIB_SHA256=y -CONFIG_CRYPTO_LZO=y -CONFIG_CRYPTO_RNG=y -CONFIG_CRYPTO_RNG2=y -CONFIG_CRYPTO_RNG_DEFAULT=y -CONFIG_CRYPTO_SHA256=y -CONFIG_CRYPTO_SHA256_ARM64=y -CONFIG_CRYPTO_SHA2_ARM64_CE=y -CONFIG_CRYPTO_SHA512=y -CONFIG_CRYPTO_SIMD=y -CONFIG_CRYPTO_ZSTD=y -CONFIG_DCACHE_WORD_ACCESS=y -CONFIG_DEBUG_MISC=y -CONFIG_DIMLIB=y -CONFIG_DMADEVICES=y -CONFIG_DMA_DIRECT_REMAP=y -CONFIG_DMA_ENGINE=y -CONFIG_DMA_OF=y -CONFIG_DMA_REMAP=y -CONFIG_DMA_VIRTUAL_CHANNELS=y -CONFIG_DTC=y -CONFIG_EDAC_SUPPORT=y -CONFIG_EINT_MTK=y -CONFIG_EXT4_FS=y -CONFIG_F2FS_FS=y -CONFIG_FIT_PARTITION=y -CONFIG_FIXED_PHY=y -CONFIG_FIX_EARLYCON_MEM=y -CONFIG_FRAME_POINTER=y -CONFIG_FS_IOMAP=y -CONFIG_FS_MBCACHE=y -CONFIG_FWNODE_MDIO=y -CONFIG_FW_LOADER_PAGED_BUF=y -CONFIG_GENERIC_ALLOCATOR=y -CONFIG_GENERIC_ARCH_TOPOLOGY=y -CONFIG_GENERIC_BUG=y -CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y -CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y -CONFIG_GENERIC_CPU_AUTOPROBE=y -CONFIG_GENERIC_CPU_VULNERABILITIES=y -CONFIG_GENERIC_CSUM=y -CONFIG_GENERIC_EARLY_IOREMAP=y -CONFIG_GENERIC_FIND_FIRST_BIT=y -CONFIG_GENERIC_GETTIMEOFDAY=y -CONFIG_GENERIC_IDLE_POLL_SETUP=y -CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y -CONFIG_GENERIC_IRQ_SHOW=y -CONFIG_GENERIC_IRQ_SHOW_LEVEL=y -CONFIG_GENERIC_LIB_DEVMEM_IS_ALLOWED=y -CONFIG_GENERIC_MSI_IRQ=y -CONFIG_GENERIC_MSI_IRQ_DOMAIN=y -CONFIG_GENERIC_PCI_IOMAP=y -CONFIG_GENERIC_PHY=y -CONFIG_GENERIC_PINCONF=y -CONFIG_GENERIC_PINCTRL_GROUPS=y -CONFIG_GENERIC_PINMUX_FUNCTIONS=y -CONFIG_GENERIC_SCHED_CLOCK=y -CONFIG_GENERIC_SMP_IDLE_THREAD=y -CONFIG_GENERIC_STRNCPY_FROM_USER=y -CONFIG_GENERIC_STRNLEN_USER=y -CONFIG_GENERIC_TIME_VSYSCALL=y -CONFIG_GLOB=y -CONFIG_GPIO_CDEV=y -CONFIG_GRO_CELLS=y -CONFIG_HANDLE_DOMAIN_IRQ=y -CONFIG_HARDIRQS_SW_RESEND=y -CONFIG_HAS_DMA=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT_MAP=y -CONFIG_HW_RANDOM=y -CONFIG_HW_RANDOM_MTK=y -CONFIG_I2C=y -CONFIG_I2C_BOARDINFO=y -CONFIG_I2C_CHARDEV=y -CONFIG_I2C_MT65XX=y -CONFIG_ICPLUS_PHY=y -CONFIG_ILLEGAL_POINTER_VALUE=0xdead000000000000 -CONFIG_INITRAMFS_SOURCE="" -CONFIG_IRQCHIP=y -CONFIG_IRQ_DOMAIN=y -CONFIG_IRQ_DOMAIN_HIERARCHY=y -CONFIG_IRQ_FORCED_THREADING=y -CONFIG_IRQ_TIME_ACCOUNTING=y -CONFIG_IRQ_WORK=y -CONFIG_JBD2=y -CONFIG_JUMP_LABEL=y -# CONFIG_LEDS_SMARTRG_LED is not set -CONFIG_LIBFDT=y -CONFIG_LOCK_DEBUGGING_SUPPORT=y -CONFIG_LOCK_SPIN_ON_OWNER=y -CONFIG_LZO_COMPRESS=y -CONFIG_LZO_DECOMPRESS=y -CONFIG_MAGIC_SYSRQ=y -CONFIG_MDIO_BUS=y -CONFIG_MDIO_DEVICE=y -CONFIG_MDIO_DEVRES=y -# CONFIG_MEDIATEK_2P5G_PHY is not set -CONFIG_MEDIATEK_GE_PHY=y -# CONFIG_MEDIATEK_GE_SOC_PHY is not set -CONFIG_MEDIATEK_WATCHDOG=y -CONFIG_MEMFD_CREATE=y -CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7 -CONFIG_MFD_SYSCON=y -CONFIG_MIGRATION=y -CONFIG_MMC=y -CONFIG_MMC_BLOCK=y -CONFIG_MMC_CQHCI=y -CONFIG_MMC_MTK=y -CONFIG_MODULES_TREE_LOOKUP=y -CONFIG_MODULES_USE_ELF_RELA=y -CONFIG_MTD_NAND_CORE=y -CONFIG_MTD_NAND_ECC=y -CONFIG_MTD_NAND_ECC_MEDIATEK=y -CONFIG_MTD_NAND_ECC_SW_HAMMING=y -CONFIG_MTD_NAND_MTK=y -CONFIG_MTD_NAND_MTK_BMT=y -CONFIG_MTD_PARSER_TRX=y -CONFIG_MTD_RAW_NAND=y -CONFIG_MTD_SPI_NAND=y -CONFIG_MTD_SPI_NOR=y -CONFIG_MTD_SPI_NOR_USE_VARIABLE_ERASE=y -CONFIG_MTD_SPLIT_FIRMWARE=y -CONFIG_MTD_SPLIT_FIT_FW=y -CONFIG_MTD_UBI=y -CONFIG_MTD_UBI_BEB_LIMIT=20 -CONFIG_MTD_UBI_BLOCK=y -CONFIG_MTD_UBI_FASTMAP=y -CONFIG_MTD_UBI_WL_THRESHOLD=4096 -# CONFIG_MTK_CMDQ is not set -# CONFIG_MTK_CQDMA is not set -CONFIG_MTK_HSDMA=y -CONFIG_MTK_INFRACFG=y -CONFIG_MTK_PMIC_WRAP=y -CONFIG_MTK_SCPSYS=y -CONFIG_MTK_SCPSYS_PM_DOMAINS=y -CONFIG_MTK_THERMAL=y -CONFIG_MTK_TIMER=y -# CONFIG_MTK_UART_APDMA is not set -CONFIG_MUTEX_SPIN_ON_OWNER=y -CONFIG_NEED_DMA_MAP_STATE=y -CONFIG_NEED_SG_DMA_LENGTH=y -CONFIG_NET_DEVLINK=y -CONFIG_NET_DSA=y -CONFIG_NET_DSA_MT7530=y -CONFIG_NET_DSA_MT7530_MDIO=y -# CONFIG_NET_DSA_MT7530_MMIO is not set -CONFIG_NET_DSA_TAG_MTK=y -CONFIG_NET_FLOW_LIMIT=y -CONFIG_NET_MEDIATEK_SOC=y -# CONFIG_NET_MEDIATEK_SOC_USXGMII is not set -CONFIG_NET_MEDIATEK_SOC_WED=y -CONFIG_NET_SELFTESTS=y -CONFIG_NET_SWITCHDEV=y -CONFIG_NET_VENDOR_MEDIATEK=y -CONFIG_NLS=y -CONFIG_NO_HZ_COMMON=y -CONFIG_NO_HZ_IDLE=y -CONFIG_NR_CPUS=2 -CONFIG_NVMEM=y -CONFIG_NVMEM_LAYOUTS=y -CONFIG_NVMEM_MTK_EFUSE=y -CONFIG_NVMEM_SYSFS=y -CONFIG_OF=y -CONFIG_OF_ADDRESS=y -CONFIG_OF_DYNAMIC=y -CONFIG_OF_EARLY_FLATTREE=y -CONFIG_OF_FLATTREE=y -CONFIG_OF_GPIO=y -CONFIG_OF_IRQ=y -CONFIG_OF_KOBJ=y -CONFIG_OF_MDIO=y -CONFIG_OF_OVERLAY=y -CONFIG_OF_RESOLVE=y -CONFIG_PADATA=y -CONFIG_PAGE_POOL=y -CONFIG_PAGE_POOL_STATS=y -CONFIG_PARTITION_PERCPU=y -CONFIG_PCI=y -CONFIG_PCIEAER=y -CONFIG_PCIEASPM=y -# CONFIG_PCIEASPM_DEFAULT is not set -CONFIG_PCIEASPM_PERFORMANCE=y -# CONFIG_PCIEASPM_POWERSAVE is not set -# CONFIG_PCIEASPM_POWER_SUPERSAVE is not set -CONFIG_PCIEPORTBUS=y -CONFIG_PCIE_MEDIATEK=y -CONFIG_PCIE_PME=y -CONFIG_PCI_DEBUG=y -CONFIG_PCI_DOMAINS=y -CONFIG_PCI_DOMAINS_GENERIC=y -CONFIG_PCI_MSI=y -CONFIG_PCI_MSI_IRQ_DOMAIN=y -CONFIG_PCS_MTK_LYNXI=y -CONFIG_PERF_EVENTS=y -CONFIG_PGTABLE_LEVELS=3 -CONFIG_PHYLIB=y -CONFIG_PHYLINK=y -CONFIG_PHYS_ADDR_T_64BIT=y -CONFIG_PHY_MTK_TPHY=y -# CONFIG_PHY_MTK_UFS is not set -# CONFIG_PHY_MTK_XSPHY is not set -CONFIG_PINCTRL=y -# CONFIG_PINCTRL_MT2712 is not set -# CONFIG_PINCTRL_MT6765 is not set -# CONFIG_PINCTRL_MT6797 is not set -CONFIG_PINCTRL_MT7622=y -# CONFIG_PINCTRL_MT7981 is not set -# CONFIG_PINCTRL_MT7986 is not set -# CONFIG_PINCTRL_MT7988 is not set -# CONFIG_PINCTRL_MT8173 is not set -# CONFIG_PINCTRL_MT8183 is not set -CONFIG_PINCTRL_MT8516=y -CONFIG_PINCTRL_MTK=y -CONFIG_PINCTRL_MTK_MOORE=y -CONFIG_PINCTRL_MTK_V2=y -CONFIG_PM=y -CONFIG_PM_CLK=y -CONFIG_PM_GENERIC_DOMAINS=y -CONFIG_PM_GENERIC_DOMAINS_OF=y -CONFIG_PM_OPP=y -CONFIG_POWER_RESET=y -CONFIG_POWER_RESET_SYSCON=y -CONFIG_POWER_SUPPLY=y -CONFIG_PRINTK_TIME=y -CONFIG_PSTORE=y -CONFIG_PSTORE_COMPRESS=y -CONFIG_PSTORE_COMPRESS_DEFAULT="deflate" -CONFIG_PSTORE_CONSOLE=y -CONFIG_PSTORE_DEFLATE_COMPRESS=y -CONFIG_PSTORE_DEFLATE_COMPRESS_DEFAULT=y -CONFIG_PSTORE_PMSG=y -CONFIG_PSTORE_RAM=y -CONFIG_PTP_1588_CLOCK_OPTIONAL=y -CONFIG_PWM=y -CONFIG_PWM_MEDIATEK=y -# CONFIG_PWM_MTK_DISP is not set -CONFIG_PWM_SYSFS=y -CONFIG_QUEUED_RWLOCKS=y -CONFIG_QUEUED_SPINLOCKS=y -CONFIG_RAS=y -CONFIG_RATIONAL=y -# CONFIG_RAVE_SP_CORE is not set -CONFIG_REALTEK_PHY=y -CONFIG_REED_SOLOMON=y -CONFIG_REED_SOLOMON_DEC8=y -CONFIG_REED_SOLOMON_ENC8=y -CONFIG_REGMAP=y -CONFIG_REGMAP_MMIO=y -CONFIG_REGULATOR=y -CONFIG_REGULATOR_FIXED_VOLTAGE=y -CONFIG_REGULATOR_MT6380=y -# CONFIG_REGULATOR_RT5190A is not set -CONFIG_RESET_CONTROLLER=y -CONFIG_RFS_ACCEL=y -CONFIG_RODATA_FULL_DEFAULT_ENABLED=y -CONFIG_RPS=y -CONFIG_RTC_CLASS=y -CONFIG_RTC_DRV_MT7622=y -CONFIG_RTC_I2C_AND_SPI=y -CONFIG_RTL8367S_GSW=y -CONFIG_RWSEM_SPIN_ON_OWNER=y -CONFIG_SCHED_MC=y -CONFIG_SCSI=y -CONFIG_SCSI_COMMON=y -# CONFIG_SECTION_MISMATCH_WARN_ONLY is not set -CONFIG_SERIAL_8250_FSL=y -CONFIG_SERIAL_8250_MT6577=y -CONFIG_SERIAL_8250_NR_UARTS=3 -CONFIG_SERIAL_8250_RUNTIME_UARTS=3 -CONFIG_SERIAL_DEV_BUS=y -CONFIG_SERIAL_DEV_CTRL_TTYPORT=y -CONFIG_SERIAL_MCTRL_GPIO=y -CONFIG_SERIAL_OF_PLATFORM=y -CONFIG_SGL_ALLOC=y -CONFIG_SG_POOL=y -CONFIG_SMP=y -CONFIG_SOCK_RX_QUEUE_MAPPING=y -CONFIG_SPARSEMEM=y -CONFIG_SPARSEMEM_EXTREME=y -CONFIG_SPARSEMEM_VMEMMAP=y -CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y -CONFIG_SPARSE_IRQ=y -CONFIG_SPI=y -CONFIG_SPI_DYNAMIC=y -CONFIG_SPI_MASTER=y -CONFIG_SPI_MEM=y -CONFIG_SPI_MT65XX=y -CONFIG_SPI_MTK_NOR=y -CONFIG_SPI_MTK_SNFI=y -CONFIG_SRCU=y -CONFIG_SWCONFIG=y -CONFIG_SWIOTLB=y -CONFIG_SWPHY=y -CONFIG_SYSCTL_EXCEPTION_TRACE=y -CONFIG_THERMAL=y -CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y -CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0 -CONFIG_THERMAL_EMULATION=y -CONFIG_THERMAL_GOV_BANG_BANG=y -CONFIG_THERMAL_GOV_FAIR_SHARE=y -CONFIG_THERMAL_GOV_STEP_WISE=y -CONFIG_THERMAL_GOV_USER_SPACE=y -CONFIG_THERMAL_OF=y -CONFIG_THERMAL_WRITABLE_TRIPS=y -CONFIG_THREAD_INFO_IN_TASK=y -CONFIG_TICK_CPU_ACCOUNTING=y -CONFIG_TIMER_OF=y -CONFIG_TIMER_PROBE=y -CONFIG_TRACE_IRQFLAGS_NMI_SUPPORT=y -CONFIG_TREE_RCU=y -CONFIG_TREE_SRCU=y -CONFIG_UBIFS_FS=y -# CONFIG_UCLAMP_TASK is not set -# CONFIG_UNMAP_KERNEL_AT_EL0 is not set -CONFIG_USB_SUPPORT=y -CONFIG_VMAP_STACK=y -CONFIG_WATCHDOG_CORE=y -CONFIG_WATCHDOG_PRETIMEOUT_DEFAULT_GOV_PANIC=y -CONFIG_WATCHDOG_PRETIMEOUT_GOV=y -# CONFIG_WATCHDOG_PRETIMEOUT_GOV_NOOP is not set -CONFIG_WATCHDOG_PRETIMEOUT_GOV_PANIC=y -CONFIG_WATCHDOG_PRETIMEOUT_GOV_SEL=m -CONFIG_WATCHDOG_SYSFS=y -CONFIG_XPS=y -CONFIG_XXHASH=y -CONFIG_ZLIB_DEFLATE=y -CONFIG_ZLIB_INFLATE=y -CONFIG_ZONE_DMA32=y -CONFIG_ZSTD_COMPRESS=y -CONFIG_ZSTD_DECOMPRESS=y diff --git a/target/linux/mediatek/mt7623/config-5.15 b/target/linux/mediatek/mt7623/config-5.15 deleted file mode 100644 index 2f12488327..0000000000 --- a/target/linux/mediatek/mt7623/config-5.15 +++ /dev/null @@ -1,577 +0,0 @@ -# CONFIG_AIO is not set -CONFIG_ALIGNMENT_TRAP=y -CONFIG_ARCH_32BIT_OFF_T=y -CONFIG_ARCH_HIBERNATION_POSSIBLE=y -CONFIG_ARCH_KEEP_MEMBLOCK=y -CONFIG_ARCH_MEDIATEK=y -CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y -CONFIG_ARCH_MULTIPLATFORM=y -CONFIG_ARCH_MULTI_V6_V7=y -CONFIG_ARCH_MULTI_V7=y -CONFIG_ARCH_NR_GPIO=0 -CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y -CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT=y -CONFIG_ARCH_SELECT_MEMORY_MODEL=y -CONFIG_ARCH_SPARSEMEM_ENABLE=y -CONFIG_ARCH_SUSPEND_POSSIBLE=y -CONFIG_ARM=y -CONFIG_ARM_APPENDED_DTB=y -CONFIG_ARM_ARCH_TIMER=y -CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y -# CONFIG_ARM_ATAG_DTB_COMPAT is not set -CONFIG_ARM_CPU_SUSPEND=y -# CONFIG_ARM_CPU_TOPOLOGY is not set -CONFIG_ARM_CRYPTO=y -CONFIG_ARM_DMA_IOMMU_ALIGNMENT=8 -CONFIG_ARM_DMA_USE_IOMMU=y -CONFIG_ARM_GIC=y -CONFIG_ARM_HAS_SG_CHAIN=y -CONFIG_ARM_L1_CACHE_SHIFT=6 -CONFIG_ARM_L1_CACHE_SHIFT_6=y -CONFIG_ARM_MEDIATEK_CPUFREQ=y -CONFIG_ARM_PATCH_IDIV=y -CONFIG_ARM_PATCH_PHYS_VIRT=y -# CONFIG_ARM_SMMU is not set -CONFIG_ARM_THUMB=y -CONFIG_ARM_THUMBEE=y -CONFIG_ARM_UNWIND=y -CONFIG_ARM_VIRT_EXT=y -CONFIG_ASYNC_TX_ENABLE_CHANNEL_SWITCH=y -CONFIG_ATAGS=y -CONFIG_AUTO_ZRELADDR=y -CONFIG_BACKLIGHT_CLASS_DEVICE=y -CONFIG_BACKLIGHT_GPIO=y -CONFIG_BACKLIGHT_LED=y -CONFIG_BACKLIGHT_PWM=y -CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK=y -CONFIG_BLK_DEV_LOOP=y -CONFIG_BLK_MQ_PCI=y -CONFIG_BLK_PM=y -CONFIG_BOUNCE=y -# CONFIG_CACHE_L2X0 is not set -CONFIG_CLEANCACHE=y -CONFIG_CLKSRC_MMIO=y -CONFIG_CLONE_BACKWARDS=y -CONFIG_CMDLINE="earlyprintk console=ttyS0,115200 rootfstype=squashfs,jffs2" -CONFIG_CMDLINE_FROM_BOOTLOADER=y -# CONFIG_CMDLINE_OVERRIDE is not set -CONFIG_CMDLINE_PARTITION=y -CONFIG_COMMON_CLK=y -CONFIG_COMMON_CLK_MEDIATEK=y -CONFIG_COMMON_CLK_MT2701=y -CONFIG_COMMON_CLK_MT2701_AUDSYS=y -CONFIG_COMMON_CLK_MT2701_BDPSYS=y -CONFIG_COMMON_CLK_MT2701_ETHSYS=y -CONFIG_COMMON_CLK_MT2701_G3DSYS=y -CONFIG_COMMON_CLK_MT2701_HIFSYS=y -CONFIG_COMMON_CLK_MT2701_IMGSYS=y -CONFIG_COMMON_CLK_MT2701_MMSYS=y -CONFIG_COMMON_CLK_MT2701_VDECSYS=y -# CONFIG_COMMON_CLK_MT7622 is not set -# CONFIG_COMMON_CLK_MT7629 is not set -# CONFIG_COMMON_CLK_MT7981 is not set -# CONFIG_COMMON_CLK_MT7986 is not set -# CONFIG_COMMON_CLK_MT7988 is not set -# CONFIG_COMMON_CLK_MT8135 is not set -# CONFIG_COMMON_CLK_MT8173 is not set -CONFIG_COMMON_CLK_MT8516=y -# CONFIG_COMMON_CLK_MT8516_AUDSYS is not set -CONFIG_COMPAT_32BIT_TIME=y -CONFIG_CONFIGFS_FS=y -CONFIG_CONSOLE_TRANSLATIONS=y -CONFIG_COREDUMP=y -# CONFIG_CPUFREQ_DT is not set -CONFIG_CPU_32v6K=y -CONFIG_CPU_32v7=y -CONFIG_CPU_ABRT_EV7=y -CONFIG_CPU_CACHE_V7=y -CONFIG_CPU_CACHE_VIPT=y -CONFIG_CPU_COPY_V6=y -CONFIG_CPU_CP15=y -CONFIG_CPU_CP15_MMU=y -CONFIG_CPU_FREQ=y -CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y -CONFIG_CPU_FREQ_GOV_ATTR_SET=y -CONFIG_CPU_FREQ_GOV_COMMON=y -CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y -CONFIG_CPU_FREQ_GOV_ONDEMAND=y -CONFIG_CPU_FREQ_GOV_PERFORMANCE=y -CONFIG_CPU_FREQ_GOV_POWERSAVE=y -# CONFIG_CPU_FREQ_GOV_USERSPACE is not set -CONFIG_CPU_FREQ_STAT=y -CONFIG_CPU_HAS_ASID=y -CONFIG_CPU_PABRT_V7=y -CONFIG_CPU_PM=y -CONFIG_CPU_RMAP=y -CONFIG_CPU_SPECTRE=y -CONFIG_CPU_THUMB_CAPABLE=y -CONFIG_CPU_TLB_V7=y -CONFIG_CPU_V7=y -CONFIG_CRC16=y -# CONFIG_CRC32_SARWATE is not set -CONFIG_CRC32_SLICEBY8=y -CONFIG_CROSS_MEMORY_ATTACH=y -CONFIG_CRYPTO_CRC32=y -CONFIG_CRYPTO_CRC32C=y -CONFIG_CRYPTO_DEFLATE=y -CONFIG_CRYPTO_DRBG=y -CONFIG_CRYPTO_DRBG_HMAC=y -CONFIG_CRYPTO_DRBG_MENU=y -CONFIG_CRYPTO_HASH_INFO=y -CONFIG_CRYPTO_HMAC=y -CONFIG_CRYPTO_HW=y -CONFIG_CRYPTO_JITTERENTROPY=y -CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC=y -CONFIG_CRYPTO_LIB_SHA256=y -CONFIG_CRYPTO_LZO=y -CONFIG_CRYPTO_RNG=y -CONFIG_CRYPTO_RNG2=y -CONFIG_CRYPTO_RNG_DEFAULT=y -CONFIG_CRYPTO_SEQIV=y -CONFIG_CRYPTO_SHA1=y -CONFIG_CRYPTO_SHA256=y -CONFIG_CRYPTO_SHA512=y -CONFIG_CRYPTO_ZSTD=y -CONFIG_DCACHE_WORD_ACCESS=y -CONFIG_DEBUG_ALIGN_RODATA=y -CONFIG_DEBUG_BUGVERBOSE=y -CONFIG_DEBUG_GPIO=y -CONFIG_DEBUG_LL=y -CONFIG_DEBUG_LL_INCLUDE="debug/8250.S" -CONFIG_DEBUG_MISC=y -CONFIG_DEBUG_MT6589_UART0=y -# CONFIG_DEBUG_MT8127_UART0 is not set -# CONFIG_DEBUG_MT8135_UART3 is not set -CONFIG_DEBUG_PREEMPT=y -CONFIG_DEBUG_UART_8250=y -CONFIG_DEBUG_UART_8250_SHIFT=2 -CONFIG_DEBUG_UART_PHYS=0x11004000 -CONFIG_DEBUG_UART_VIRT=0xf1004000 -CONFIG_DEBUG_UNCOMPRESS=y -# CONFIG_DEVFREQ_GOV_PASSIVE is not set -# CONFIG_DEVFREQ_GOV_PERFORMANCE is not set -# CONFIG_DEVFREQ_GOV_POWERSAVE is not set -CONFIG_DEVFREQ_GOV_SIMPLE_ONDEMAND=y -# CONFIG_DEVFREQ_GOV_USERSPACE is not set -# CONFIG_DEVFREQ_THERMAL is not set -CONFIG_DIMLIB=y -CONFIG_DMADEVICES=y -CONFIG_DMA_ENGINE=y -CONFIG_DMA_OF=y -CONFIG_DMA_OPS=y -CONFIG_DMA_REMAP=y -CONFIG_DMA_SHARED_BUFFER=y -CONFIG_DMA_VIRTUAL_CHANNELS=y -CONFIG_DRM=y -CONFIG_DRM_BRIDGE=y -CONFIG_DRM_DISPLAY_CONNECTOR=y -CONFIG_DRM_FBDEV_EMULATION=y -CONFIG_DRM_FBDEV_OVERALLOC=100 -CONFIG_DRM_GEM_CMA_HELPER=y -CONFIG_DRM_GEM_SHMEM_HELPER=y -CONFIG_DRM_KMS_HELPER=y -CONFIG_DRM_LIMA=y -CONFIG_DRM_LVDS_CODEC=y -CONFIG_DRM_MEDIATEK=y -CONFIG_DRM_MEDIATEK_HDMI=y -CONFIG_DRM_MIPI_DSI=y -CONFIG_DRM_PANEL=y -CONFIG_DRM_PANEL_BRIDGE=y -CONFIG_DRM_PANEL_ORIENTATION_QUIRKS=y -CONFIG_DRM_PANEL_RASPBERRYPI_TOUCHSCREEN=y -CONFIG_DRM_SCHED=y -CONFIG_DRM_SIMPLE_BRIDGE=y -CONFIG_DTC=y -CONFIG_DUMMY_CONSOLE=y -CONFIG_EARLY_PRINTK=y -CONFIG_EDAC_ATOMIC_SCRUB=y -CONFIG_EDAC_SUPPORT=y -CONFIG_EINT_MTK=y -CONFIG_ELF_CORE=y -CONFIG_EXT4_FS=y -CONFIG_EXTCON=y -CONFIG_F2FS_FS=y -CONFIG_FB=y -CONFIG_FB_CFB_COPYAREA=y -CONFIG_FB_CFB_FILLRECT=y -CONFIG_FB_CFB_IMAGEBLIT=y -CONFIG_FB_CMDLINE=y -CONFIG_FB_DEFERRED_IO=y -CONFIG_FB_SYS_COPYAREA=y -CONFIG_FB_SYS_FILLRECT=y -CONFIG_FB_SYS_FOPS=y -CONFIG_FB_SYS_IMAGEBLIT=y -CONFIG_FIT_PARTITION=y -CONFIG_FIXED_PHY=y -CONFIG_FIX_EARLYCON_MEM=y -CONFIG_FONT_8x16=y -CONFIG_FONT_8x8=y -CONFIG_FONT_SUPPORT=y -CONFIG_FRAMEBUFFER_CONSOLE=y -CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y -CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y -CONFIG_FREEZER=y -CONFIG_FS_IOMAP=y -CONFIG_FS_MBCACHE=y -CONFIG_FWNODE_MDIO=y -CONFIG_FW_CACHE=y -CONFIG_FW_LOADER_PAGED_BUF=y -CONFIG_GENERIC_ALLOCATOR=y -CONFIG_GENERIC_BUG=y -CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y -CONFIG_GENERIC_CPU_AUTOPROBE=y -CONFIG_GENERIC_CPU_VULNERABILITIES=y -CONFIG_GENERIC_EARLY_IOREMAP=y -CONFIG_GENERIC_GETTIMEOFDAY=y -CONFIG_GENERIC_IDLE_POLL_SETUP=y -CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y -CONFIG_GENERIC_IRQ_MIGRATION=y -CONFIG_GENERIC_IRQ_MULTI_HANDLER=y -CONFIG_GENERIC_IRQ_SHOW=y -CONFIG_GENERIC_IRQ_SHOW_LEVEL=y -CONFIG_GENERIC_LIB_DEVMEM_IS_ALLOWED=y -CONFIG_GENERIC_MSI_IRQ=y -CONFIG_GENERIC_MSI_IRQ_DOMAIN=y -CONFIG_GENERIC_PCI_IOMAP=y -CONFIG_GENERIC_PHY=y -CONFIG_GENERIC_PINCONF=y -CONFIG_GENERIC_PINCTRL_GROUPS=y -CONFIG_GENERIC_PINMUX_FUNCTIONS=y -CONFIG_GENERIC_SCHED_CLOCK=y -CONFIG_GENERIC_SMP_IDLE_THREAD=y -CONFIG_GENERIC_STRNCPY_FROM_USER=y -CONFIG_GENERIC_STRNLEN_USER=y -CONFIG_GENERIC_TIME_VSYSCALL=y -CONFIG_GENERIC_VDSO_32=y -CONFIG_GPIO_CDEV=y -CONFIG_GRO_CELLS=y -CONFIG_HANDLE_DOMAIN_IRQ=y -CONFIG_HARDEN_BRANCH_PREDICTOR=y -CONFIG_HARDIRQS_SW_RESEND=y -CONFIG_HAS_DMA=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT_MAP=y -CONFIG_HAVE_SMP=y -CONFIG_HDMI=y -CONFIG_HID=y -CONFIG_HIGHMEM=y -CONFIG_HIGHPTE=y -CONFIG_HOTPLUG_CPU=y -CONFIG_HWMON=y -CONFIG_HW_CONSOLE=y -CONFIG_HW_RANDOM=y -CONFIG_HW_RANDOM_MTK=y -CONFIG_HZ_FIXED=0 -CONFIG_I2C=y -CONFIG_I2C_ALGOBIT=y -CONFIG_I2C_BOARDINFO=y -CONFIG_I2C_CHARDEV=y -CONFIG_I2C_MT65XX=y -CONFIG_ICPLUS_PHY=y -CONFIG_IIO=y -CONFIG_INITRAMFS_SOURCE="" -CONFIG_INPUT=y -CONFIG_INPUT_EVDEV=y -CONFIG_INPUT_KEYBOARD=y -CONFIG_INPUT_TOUCHSCREEN=y -CONFIG_IOMMU_API=y -# CONFIG_IOMMU_DEBUGFS is not set -CONFIG_IOMMU_DEFAULT_DMA_STRICT=y -CONFIG_IOMMU_IO_PGTABLE=y -CONFIG_IOMMU_IO_PGTABLE_ARMV7S=y -# CONFIG_IOMMU_IO_PGTABLE_ARMV7S_SELFTEST is not set -# CONFIG_IOMMU_IO_PGTABLE_LPAE is not set -CONFIG_IOMMU_SUPPORT=y -CONFIG_IRQCHIP=y -CONFIG_IRQ_DOMAIN=y -CONFIG_IRQ_DOMAIN_HIERARCHY=y -CONFIG_IRQ_FORCED_THREADING=y -CONFIG_IRQ_WORK=y -CONFIG_JBD2=y -CONFIG_KALLSYMS=y -CONFIG_KCMP=y -CONFIG_KEYBOARD_MTK_PMIC=y -CONFIG_KMAP_LOCAL=y -CONFIG_KMAP_LOCAL_NON_LINEAR_PTE_ARRAY=y -CONFIG_LCD_CLASS_DEVICE=y -CONFIG_LCD_PLATFORM=y -CONFIG_LEDS_MT6323=y -# CONFIG_LEDS_SMARTRG_LED is not set -CONFIG_LIBFDT=y -CONFIG_LOCK_DEBUGGING_SUPPORT=y -CONFIG_LOCK_SPIN_ON_OWNER=y -CONFIG_LOGO=y -CONFIG_LOGO_LINUX_CLUT224=y -# CONFIG_LOGO_LINUX_MONO is not set -# CONFIG_LOGO_LINUX_VGA16 is not set -CONFIG_LZO_COMPRESS=y -CONFIG_LZO_DECOMPRESS=y -# CONFIG_MACH_MT2701 is not set -# CONFIG_MACH_MT6589 is not set -# CONFIG_MACH_MT6592 is not set -CONFIG_MACH_MT7623=y -# CONFIG_MACH_MT7629 is not set -# CONFIG_MACH_MT8127 is not set -# CONFIG_MACH_MT8135 is not set -CONFIG_MAGIC_SYSRQ=y -CONFIG_MAILBOX=y -# CONFIG_MAILBOX_TEST is not set -CONFIG_MDIO_BITBANG=y -CONFIG_MDIO_BUS=y -CONFIG_MDIO_DEVICE=y -CONFIG_MDIO_DEVRES=y -CONFIG_MDIO_GPIO=y -CONFIG_MEDIATEK_GE_PHY=y -CONFIG_MEDIATEK_MT6577_AUXADC=y -CONFIG_MEDIATEK_WATCHDOG=y -CONFIG_MEMFD_CREATE=y -CONFIG_MEMORY=y -CONFIG_MFD_CORE=y -# CONFIG_MFD_HI6421_SPMI is not set -CONFIG_MFD_MT6397=y -CONFIG_MFD_SYSCON=y -CONFIG_MIGHT_HAVE_CACHE_L2X0=y -CONFIG_MIGRATION=y -CONFIG_MMC=y -CONFIG_MMC_BLOCK=y -CONFIG_MMC_CQHCI=y -CONFIG_MMC_MTK=y -CONFIG_MMC_SDHCI=y -# CONFIG_MMC_SDHCI_PCI is not set -CONFIG_MMC_SDHCI_PLTFM=y -CONFIG_MODULES_USE_ELF_REL=y -CONFIG_MTD_CMDLINE_PARTS=y -# CONFIG_MTD_NAND_ECC_MEDIATEK is not set -CONFIG_MTD_SPI_NOR=y -CONFIG_MTD_SPLIT_FIRMWARE=y -CONFIG_MTD_SPLIT_UIMAGE_FW=y -CONFIG_MTD_UBI=y -CONFIG_MTD_UBI_BEB_LIMIT=20 -CONFIG_MTD_UBI_BLOCK=y -CONFIG_MTD_UBI_WL_THRESHOLD=4096 -CONFIG_MTK_CMDQ=y -CONFIG_MTK_CMDQ_MBOX=y -CONFIG_MTK_CQDMA=y -# CONFIG_MTK_HSDMA is not set -CONFIG_MTK_INFRACFG=y -CONFIG_MTK_IOMMU=y -CONFIG_MTK_IOMMU_V1=y -CONFIG_MTK_MMSYS=y -CONFIG_MTK_PMIC_WRAP=y -CONFIG_MTK_SCPSYS=y -CONFIG_MTK_SCPSYS_PM_DOMAINS=y -CONFIG_MTK_SMI=y -CONFIG_MTK_THERMAL=y -CONFIG_MTK_TIMER=y -# CONFIG_MTK_UART_APDMA is not set -# CONFIG_MUSB_PIO_ONLY is not set -CONFIG_MUTEX_SPIN_ON_OWNER=y -CONFIG_NEED_DMA_MAP_STATE=y -CONFIG_NEED_SG_DMA_LENGTH=y -CONFIG_NEON=y -CONFIG_NET_DEVLINK=y -CONFIG_NET_DSA=y -CONFIG_NET_DSA_MT7530=y -CONFIG_NET_DSA_MT7530_MDIO=y -# CONFIG_NET_DSA_MT7530_MMIO is not set -CONFIG_NET_DSA_TAG_MTK=y -CONFIG_NET_FLOW_LIMIT=y -CONFIG_NET_MEDIATEK_SOC=y -CONFIG_NET_MEDIATEK_SOC_WED=y -CONFIG_NET_SELFTESTS=y -CONFIG_NET_SWITCHDEV=y -CONFIG_NET_VENDOR_MEDIATEK=y -# CONFIG_NET_VENDOR_WIZNET is not set -CONFIG_NLS=y -CONFIG_NOP_USB_XCEIV=y -CONFIG_NO_HZ=y -CONFIG_NO_HZ_COMMON=y -CONFIG_NO_HZ_IDLE=y -CONFIG_NR_CPUS=4 -CONFIG_NVMEM=y -CONFIG_NVMEM_MTK_EFUSE=y -# CONFIG_NVMEM_SPMI_SDAM is not set -CONFIG_NVMEM_SYSFS=y -CONFIG_OF=y -CONFIG_OF_ADDRESS=y -CONFIG_OF_DYNAMIC=y -CONFIG_OF_EARLY_FLATTREE=y -CONFIG_OF_FLATTREE=y -CONFIG_OF_GPIO=y -CONFIG_OF_IOMMU=y -CONFIG_OF_IRQ=y -CONFIG_OF_KOBJ=y -CONFIG_OF_MDIO=y -CONFIG_OF_OVERLAY=y -CONFIG_OF_RESOLVE=y -CONFIG_OLD_SIGACTION=y -CONFIG_OLD_SIGSUSPEND3=y -CONFIG_PADATA=y -CONFIG_PAGE_OFFSET=0xC0000000 -CONFIG_PAGE_POOL=y -CONFIG_PAGE_POOL_STATS=y -CONFIG_PCI=y -CONFIG_PCIEAER=y -CONFIG_PCIEPORTBUS=y -CONFIG_PCIE_MEDIATEK=y -CONFIG_PCIE_PME=y -CONFIG_PCI_DOMAINS=y -CONFIG_PCI_DOMAINS_GENERIC=y -CONFIG_PCI_MSI=y -CONFIG_PCI_MSI_IRQ_DOMAIN=y -CONFIG_PCS_MTK_LYNXI=y -CONFIG_PERF_USE_VMALLOC=y -CONFIG_PGTABLE_LEVELS=2 -CONFIG_PHYLIB=y -CONFIG_PHYLINK=y -CONFIG_PHY_MTK_HDMI=y -CONFIG_PHY_MTK_MIPI_DSI=y -CONFIG_PHY_MTK_TPHY=y -# CONFIG_PHY_MTK_UFS is not set -# CONFIG_PHY_MTK_XSPHY is not set -CONFIG_PINCTRL=y -CONFIG_PINCTRL_MT2701=y -CONFIG_PINCTRL_MT6397=y -CONFIG_PINCTRL_MT7623=y -CONFIG_PINCTRL_MTK=y -CONFIG_PINCTRL_MTK_MOORE=y -CONFIG_PINCTRL_MTK_V2=y -CONFIG_PM=y -CONFIG_PM_CLK=y -CONFIG_PM_DEVFREQ=y -# CONFIG_PM_DEVFREQ_EVENT is not set -CONFIG_PM_GENERIC_DOMAINS=y -CONFIG_PM_GENERIC_DOMAINS_OF=y -CONFIG_PM_GENERIC_DOMAINS_SLEEP=y -CONFIG_PM_OPP=y -CONFIG_PM_SLEEP=y -CONFIG_PM_SLEEP_SMP=y -CONFIG_POWER_RESET=y -# CONFIG_POWER_RESET_MT6323 is not set -CONFIG_POWER_SUPPLY=y -CONFIG_POWER_SUPPLY_HWMON=y -CONFIG_PREEMPT=y -CONFIG_PREEMPTION=y -CONFIG_PREEMPT_COUNT=y -# CONFIG_PREEMPT_NONE is not set -CONFIG_PREEMPT_RCU=y -CONFIG_PRINTK_TIME=y -CONFIG_PTP_1588_CLOCK_OPTIONAL=y -CONFIG_PWM=y -CONFIG_PWM_MEDIATEK=y -# CONFIG_PWM_MTK_DISP is not set -CONFIG_PWM_SYSFS=y -CONFIG_RAS=y -CONFIG_RATIONAL=y -CONFIG_REGMAP=y -CONFIG_REGMAP_MMIO=y -CONFIG_REGULATOR=y -CONFIG_REGULATOR_FIXED_VOLTAGE=y -CONFIG_REGULATOR_GPIO=y -CONFIG_REGULATOR_MT6323=y -# CONFIG_REGULATOR_MT6358 is not set -# CONFIG_REGULATOR_MT6380 is not set -# CONFIG_REGULATOR_MT6397 is not set -# CONFIG_REGULATOR_RT5190A is not set -# CONFIG_REGULATOR_QCOM_LABIBB is not set -# CONFIG_REGULATOR_QCOM_SPMI is not set -# CONFIG_REGULATOR_QCOM_USB_VBUS is not set -CONFIG_RESET_CONTROLLER=y -CONFIG_RFS_ACCEL=y -CONFIG_RPS=y -CONFIG_RTC_CLASS=y -# CONFIG_RTC_DRV_MT6397 is not set -# CONFIG_RTC_DRV_MT7622 is not set -CONFIG_RTC_I2C_AND_SPI=y -CONFIG_RTC_MC146818_LIB=y -# CONFIG_RTL8367S_GSW is not set -CONFIG_RWSEM_SPIN_ON_OWNER=y -# CONFIG_SERIAL_8250_DMA is not set -CONFIG_SERIAL_8250_FSL=y -CONFIG_SERIAL_8250_MT6577=y -CONFIG_SERIAL_8250_NR_UARTS=4 -CONFIG_SERIAL_8250_RUNTIME_UARTS=4 -CONFIG_SERIAL_MCTRL_GPIO=y -CONFIG_SGL_ALLOC=y -CONFIG_SMP=y -# CONFIG_SMP_ON_UP is not set -CONFIG_SOCK_RX_QUEUE_MAPPING=y -CONFIG_SPARSE_IRQ=y -CONFIG_SPI=y -CONFIG_SPI_BITBANG=y -CONFIG_SPI_DYNAMIC=y -CONFIG_SPI_MASTER=y -CONFIG_SPI_MEM=y -CONFIG_SPI_MT65XX=y -# CONFIG_SPI_MTK_NOR is not set -CONFIG_SPMI=y -# CONFIG_SPMI_HISI3670 is not set -CONFIG_SRCU=y -# CONFIG_STRIP_ASM_SYMS is not set -CONFIG_SUSPEND=y -CONFIG_SUSPEND_FREEZER=y -CONFIG_SWPHY=y -CONFIG_SWP_EMULATE=y -CONFIG_SYNC_FILE=y -CONFIG_SYS_SUPPORTS_APM_EMULATION=y -CONFIG_THERMAL=y -CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y -CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0 -CONFIG_THERMAL_GOV_STEP_WISE=y -CONFIG_THERMAL_OF=y -CONFIG_TICK_CPU_ACCOUNTING=y -CONFIG_TIMER_OF=y -CONFIG_TIMER_PROBE=y -CONFIG_TOUCHSCREEN_EDT_FT5X06=y -CONFIG_TREE_RCU=y -CONFIG_TREE_SRCU=y -# CONFIG_UACCE is not set -CONFIG_UBIFS_FS=y -CONFIG_UEVENT_HELPER_PATH="" -CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h" -CONFIG_UNINLINE_SPIN_UNLOCK=y -CONFIG_UNWINDER_ARM=y -CONFIG_USB=y -CONFIG_USB_COMMON=y -CONFIG_USB_F_ACM=y -CONFIG_USB_F_ECM=y -CONFIG_USB_F_MASS_STORAGE=y -CONFIG_USB_GADGET=y -CONFIG_USB_GPIO_VBUS=y -CONFIG_USB_G_MULTI=y -CONFIG_USB_G_MULTI_CDC=y -# CONFIG_USB_G_MULTI_RNDIS is not set -CONFIG_USB_HID=y -CONFIG_USB_HIDDEV=y -CONFIG_USB_INVENTRA_DMA=y -CONFIG_USB_LIBCOMPOSITE=y -CONFIG_USB_MUSB_DUAL_ROLE=y -CONFIG_USB_MUSB_HDRC=y -CONFIG_USB_MUSB_MEDIATEK=y -CONFIG_USB_OTG=y -CONFIG_USB_PHY=y -CONFIG_USB_ROLE_SWITCH=y -CONFIG_USB_SUPPORT=y -CONFIG_USB_U_ETHER=y -CONFIG_USB_U_SERIAL=y -CONFIG_USE_OF=y -CONFIG_VFP=y -CONFIG_VFPv3=y -CONFIG_VIDEOMODE_HELPERS=y -CONFIG_VM_EVENT_COUNTERS=y -CONFIG_VT=y -CONFIG_VT_CONSOLE=y -CONFIG_VT_CONSOLE_SLEEP=y -CONFIG_VT_HW_CONSOLE_BINDING=y -CONFIG_WATCHDOG_CORE=y -CONFIG_XPS=y -CONFIG_XXHASH=y -CONFIG_XZ_DEC_ARM=y -CONFIG_XZ_DEC_BCJ=y -CONFIG_ZBOOT_ROM_BSS=0 -CONFIG_ZBOOT_ROM_TEXT=0 -CONFIG_ZLIB_DEFLATE=y -CONFIG_ZLIB_INFLATE=y -CONFIG_ZSTD_COMPRESS=y -CONFIG_ZSTD_DECOMPRESS=y diff --git a/target/linux/mediatek/mt7629/config-5.15 b/target/linux/mediatek/mt7629/config-5.15 deleted file mode 100644 index c42ada6d23..0000000000 --- a/target/linux/mediatek/mt7629/config-5.15 +++ /dev/null @@ -1,327 +0,0 @@ -CONFIG_ALIGNMENT_TRAP=y -CONFIG_ARCH_32BIT_OFF_T=y -CONFIG_ARCH_HIBERNATION_POSSIBLE=y -CONFIG_ARCH_KEEP_MEMBLOCK=y -CONFIG_ARCH_MEDIATEK=y -CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y -CONFIG_ARCH_MULTIPLATFORM=y -CONFIG_ARCH_MULTI_V6_V7=y -CONFIG_ARCH_MULTI_V7=y -CONFIG_ARCH_NR_GPIO=0 -CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y -CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT=y -CONFIG_ARCH_SELECT_MEMORY_MODEL=y -CONFIG_ARCH_SPARSEMEM_ENABLE=y -CONFIG_ARCH_SUSPEND_POSSIBLE=y -CONFIG_ARM=y -CONFIG_ARM_ARCH_TIMER=y -CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y -CONFIG_ARM_CRYPTO=y -CONFIG_ARM_GIC=y -CONFIG_ARM_HAS_SG_CHAIN=y -CONFIG_ARM_HEAVY_MB=y -CONFIG_ARM_L1_CACHE_SHIFT=6 -CONFIG_ARM_L1_CACHE_SHIFT_6=y -CONFIG_ARM_PATCH_IDIV=y -CONFIG_ARM_PATCH_PHYS_VIRT=y -CONFIG_ARM_THUMB=y -CONFIG_ARM_UNWIND=y -CONFIG_ARM_VIRT_EXT=y -CONFIG_ATAGS=y -CONFIG_AUTO_ZRELADDR=y -CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK=y -CONFIG_BLK_DEV_SD=y -CONFIG_BLK_MQ_PCI=y -CONFIG_BLK_PM=y -CONFIG_BSD_PROCESS_ACCT=y -CONFIG_BSD_PROCESS_ACCT_V3=y -CONFIG_CACHE_L2X0=y -# CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE is not set -CONFIG_CC_OPTIMIZE_FOR_SIZE=y -CONFIG_CHR_DEV_SCH=y -CONFIG_CLKSRC_MMIO=y -CONFIG_CLONE_BACKWARDS=y -CONFIG_CMDLINE="rootfstype=squashfs,jffs2" -CONFIG_CMDLINE_FROM_BOOTLOADER=y -CONFIG_CMDLINE_OVERRIDE=y -CONFIG_COMMON_CLK=y -CONFIG_COMMON_CLK_MEDIATEK=y -# CONFIG_COMMON_CLK_MT2701 is not set -# CONFIG_COMMON_CLK_MT7622 is not set -CONFIG_COMMON_CLK_MT7629=y -CONFIG_COMMON_CLK_MT7629_ETHSYS=y -CONFIG_COMMON_CLK_MT7629_HIFSYS=y -# CONFIG_COMMON_CLK_MT7981 is not set -# CONFIG_COMMON_CLK_MT7986 is not set -# CONFIG_COMMON_CLK_MT7988 is not set -# CONFIG_COMMON_CLK_MT8135 is not set -# CONFIG_COMMON_CLK_MT8173 is not set -CONFIG_COMMON_CLK_MT8516=y -# CONFIG_COMMON_CLK_MT8516_AUDSYS is not set -CONFIG_COMPAT_32BIT_TIME=y -CONFIG_CPU_32v6K=y -CONFIG_CPU_32v7=y -CONFIG_CPU_ABRT_EV7=y -CONFIG_CPU_CACHE_V7=y -CONFIG_CPU_CACHE_VIPT=y -CONFIG_CPU_COPY_V6=y -CONFIG_CPU_CP15=y -CONFIG_CPU_CP15_MMU=y -CONFIG_CPU_HAS_ASID=y -CONFIG_CPU_IDLE=y -CONFIG_CPU_IDLE_GOV_MENU=y -CONFIG_CPU_PABRT_V7=y -CONFIG_CPU_PM=y -CONFIG_CPU_RMAP=y -CONFIG_CPU_SPECTRE=y -CONFIG_CPU_THUMB_CAPABLE=y -CONFIG_CPU_TLB_V7=y -CONFIG_CPU_V7=y -CONFIG_CRC16=y -CONFIG_CRYPTO_DEFLATE=y -CONFIG_CRYPTO_HASH_INFO=y -CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC=y -CONFIG_CRYPTO_LZO=y -CONFIG_CRYPTO_RNG2=y -CONFIG_CRYPTO_ZSTD=y -CONFIG_DCACHE_WORD_ACCESS=y -CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S" -CONFIG_DEBUG_MISC=y -CONFIG_DEFAULT_HOSTNAME="(mt7629)" -CONFIG_DIMLIB=y -CONFIG_DMA_OPS=y -CONFIG_DMA_REMAP=y -CONFIG_DTC=y -CONFIG_EDAC_ATOMIC_SCRUB=y -CONFIG_EDAC_SUPPORT=y -CONFIG_EINT_MTK=y -# CONFIG_FIT_PARTITION is not set -CONFIG_FIXED_PHY=y -CONFIG_FIX_EARLYCON_MEM=y -CONFIG_FWNODE_MDIO=y -CONFIG_FW_LOADER_PAGED_BUF=y -CONFIG_GENERIC_ALLOCATOR=y -CONFIG_GENERIC_ARCH_TOPOLOGY=y -CONFIG_GENERIC_BUG=y -CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y -CONFIG_GENERIC_CPU_AUTOPROBE=y -CONFIG_GENERIC_CPU_VULNERABILITIES=y -CONFIG_GENERIC_EARLY_IOREMAP=y -CONFIG_GENERIC_GETTIMEOFDAY=y -CONFIG_GENERIC_IDLE_POLL_SETUP=y -CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y -CONFIG_GENERIC_IRQ_MIGRATION=y -CONFIG_GENERIC_IRQ_MULTI_HANDLER=y -CONFIG_GENERIC_IRQ_SHOW=y -CONFIG_GENERIC_IRQ_SHOW_LEVEL=y -CONFIG_GENERIC_LIB_DEVMEM_IS_ALLOWED=y -CONFIG_GENERIC_MSI_IRQ=y -CONFIG_GENERIC_MSI_IRQ_DOMAIN=y -CONFIG_GENERIC_PCI_IOMAP=y -CONFIG_GENERIC_PHY=y -CONFIG_GENERIC_PINCONF=y -CONFIG_GENERIC_PINCTRL_GROUPS=y -CONFIG_GENERIC_PINMUX_FUNCTIONS=y -CONFIG_GENERIC_SCHED_CLOCK=y -CONFIG_GENERIC_SMP_IDLE_THREAD=y -CONFIG_GENERIC_STRNCPY_FROM_USER=y -CONFIG_GENERIC_STRNLEN_USER=y -CONFIG_GENERIC_TIME_VSYSCALL=y -CONFIG_GENERIC_VDSO_32=y -CONFIG_GPIO_CDEV=y -CONFIG_GRO_CELLS=y -CONFIG_HANDLE_DOMAIN_IRQ=y -CONFIG_HARDEN_BRANCH_PREDICTOR=y -CONFIG_HARDIRQS_SW_RESEND=y -CONFIG_HAS_DMA=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT_MAP=y -CONFIG_HAVE_SMP=y -CONFIG_HOTPLUG_CPU=y -CONFIG_HW_RANDOM=y -CONFIG_HW_RANDOM_MTK=y -CONFIG_HZ_FIXED=0 -CONFIG_INITRAMFS_SOURCE="" -CONFIG_IRQCHIP=y -CONFIG_IRQ_DOMAIN=y -CONFIG_IRQ_DOMAIN_HIERARCHY=y -CONFIG_IRQ_FORCED_THREADING=y -CONFIG_IRQ_TIME_ACCOUNTING=y -CONFIG_IRQ_WORK=y -# CONFIG_LEDS_BRIGHTNESS_HW_CHANGED is not set -# CONFIG_LEDS_SMARTRG_LED is not set -CONFIG_LIBFDT=y -CONFIG_LOCK_DEBUGGING_SUPPORT=y -CONFIG_LOCK_SPIN_ON_OWNER=y -CONFIG_LZO_COMPRESS=y -CONFIG_LZO_DECOMPRESS=y -# CONFIG_MACH_MT2701 is not set -# CONFIG_MACH_MT6589 is not set -# CONFIG_MACH_MT6592 is not set -# CONFIG_MACH_MT7623 is not set -CONFIG_MACH_MT7629=y -# CONFIG_MACH_MT8127 is not set -# CONFIG_MACH_MT8135 is not set -CONFIG_MDIO_BUS=y -CONFIG_MDIO_DEVICE=y -CONFIG_MDIO_DEVRES=y -CONFIG_MEDIATEK_GE_PHY=y -CONFIG_MEDIATEK_WATCHDOG=y -CONFIG_MEMFD_CREATE=y -CONFIG_MFD_SYSCON=y -CONFIG_MIGHT_HAVE_CACHE_L2X0=y -CONFIG_MIGRATION=y -CONFIG_MODULES_USE_ELF_REL=y -CONFIG_MTD_NAND_CORE=y -CONFIG_MTD_NAND_ECC=y -CONFIG_MTD_NAND_ECC_MEDIATEK=y -CONFIG_MTD_NAND_ECC_SW_HAMMING=y -CONFIG_MTD_NAND_MTK_BMT=y -CONFIG_MTD_RAW_NAND=y -CONFIG_MTD_SPI_NAND=y -CONFIG_MTD_SPI_NOR=y -CONFIG_MTD_SPLIT_FIRMWARE=y -CONFIG_MTD_SPLIT_FIT_FW=y -CONFIG_MTD_UBI=y -CONFIG_MTD_UBI_BEB_LIMIT=20 -CONFIG_MTD_UBI_BLOCK=y -CONFIG_MTD_UBI_WL_THRESHOLD=4096 -# CONFIG_MTK_CMDQ is not set -CONFIG_MTK_INFRACFG=y -# CONFIG_MTK_PMIC_WRAP is not set -CONFIG_MTK_SCPSYS=y -CONFIG_MTK_SCPSYS_PM_DOMAINS=y -CONFIG_MTK_TIMER=y -CONFIG_MUTEX_SPIN_ON_OWNER=y -CONFIG_NEED_DMA_MAP_STATE=y -CONFIG_NETFILTER=y -CONFIG_NET_DEVLINK=y -CONFIG_NET_DSA=y -CONFIG_NET_DSA_MT7530=y -CONFIG_NET_DSA_MT7530_MDIO=y -# CONFIG_NET_DSA_MT7530_MMIO is not set -CONFIG_NET_DSA_TAG_MTK=y -CONFIG_NET_FLOW_LIMIT=y -CONFIG_NET_MEDIATEK_SOC=y -CONFIG_NET_MEDIATEK_SOC_WED=y -CONFIG_NET_SELFTESTS=y -CONFIG_NET_SWITCHDEV=y -CONFIG_NET_VENDOR_MEDIATEK=y -CONFIG_NLS=y -CONFIG_NO_HZ_COMMON=y -CONFIG_NO_HZ_IDLE=y -CONFIG_NR_CPUS=2 -CONFIG_NVMEM=y -# CONFIG_NVMEM_MTK_EFUSE is not set -CONFIG_NVMEM_SYSFS=y -CONFIG_OF=y -CONFIG_OF_ADDRESS=y -CONFIG_OF_EARLY_FLATTREE=y -CONFIG_OF_FLATTREE=y -CONFIG_OF_GPIO=y -CONFIG_OF_IRQ=y -CONFIG_OF_KOBJ=y -CONFIG_OF_MDIO=y -CONFIG_OLD_SIGACTION=y -CONFIG_OLD_SIGSUSPEND3=y -CONFIG_OUTER_CACHE=y -CONFIG_OUTER_CACHE_SYNC=y -CONFIG_PADATA=y -CONFIG_PAGE_OFFSET=0xC0000000 -CONFIG_PAGE_POOL=y -CONFIG_PAGE_POOL_STATS=y -CONFIG_PCI=y -CONFIG_PCIEAER=y -CONFIG_PCIEPORTBUS=y -CONFIG_PCIE_MEDIATEK=y -CONFIG_PCIE_PME=y -CONFIG_PCI_DOMAINS=y -CONFIG_PCI_DOMAINS_GENERIC=y -CONFIG_PCI_MSI=y -CONFIG_PCI_MSI_IRQ_DOMAIN=y -CONFIG_PCS_MTK_LYNXI=y -CONFIG_PERF_USE_VMALLOC=y -CONFIG_PGTABLE_LEVELS=2 -CONFIG_PHYLIB=y -CONFIG_PHYLINK=y -CONFIG_PHY_MTK_TPHY=y -# CONFIG_PHY_MTK_UFS is not set -# CONFIG_PHY_MTK_XSPHY is not set -CONFIG_PINCTRL=y -CONFIG_PINCTRL_MT7629=y -CONFIG_PINCTRL_MTK_MOORE=y -CONFIG_PINCTRL_MTK_V2=y -CONFIG_PM=y -CONFIG_PM_CLK=y -CONFIG_PM_GENERIC_DOMAINS=y -CONFIG_PM_GENERIC_DOMAINS_OF=y -CONFIG_PTP_1588_CLOCK_OPTIONAL=y -CONFIG_PWM=y -CONFIG_PWM_MEDIATEK=y -# CONFIG_PWM_MTK_DISP is not set -CONFIG_PWM_SYSFS=y -CONFIG_RAS=y -CONFIG_RATIONAL=y -CONFIG_REGMAP=y -CONFIG_REGMAP_MMIO=y -CONFIG_RESET_CONTROLLER=y -CONFIG_RFS_ACCEL=y -CONFIG_RPS=y -# CONFIG_RTL8367S_GSW is not set -CONFIG_RWSEM_SPIN_ON_OWNER=y -CONFIG_SCSI=y -CONFIG_SCSI_COMMON=y -CONFIG_SERIAL_8250_FSL=y -CONFIG_SERIAL_8250_MT6577=y -CONFIG_SERIAL_8250_NR_UARTS=3 -CONFIG_SERIAL_8250_RUNTIME_UARTS=3 -CONFIG_SERIAL_MCTRL_GPIO=y -CONFIG_SERIAL_OF_PLATFORM=y -CONFIG_SGL_ALLOC=y -CONFIG_SG_POOL=y -CONFIG_SMP=y -CONFIG_SMP_ON_UP=y -CONFIG_SOCK_RX_QUEUE_MAPPING=y -CONFIG_SPARSE_IRQ=y -CONFIG_SPI=y -CONFIG_SPI_MASTER=y -CONFIG_SPI_MEM=y -CONFIG_SPI_MT65XX=y -CONFIG_SPI_MTK_NOR=y -CONFIG_SPI_MTK_SNFI=y -CONFIG_SRCU=y -CONFIG_STACKTRACE=y -# CONFIG_SWAP is not set -CONFIG_SWCONFIG=y -CONFIG_SWPHY=y -CONFIG_SWP_EMULATE=y -CONFIG_SYS_SUPPORTS_APM_EMULATION=y -CONFIG_TICK_CPU_ACCOUNTING=y -CONFIG_TIMER_OF=y -CONFIG_TIMER_PROBE=y -CONFIG_TREE_RCU=y -CONFIG_TREE_SRCU=y -CONFIG_UBIFS_FS=y -CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h" -CONFIG_UNWINDER_ARM=y -CONFIG_USB=y -CONFIG_USB_COMMON=y -CONFIG_USB_SUPPORT=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_MTK=y -# CONFIG_USB_XHCI_PLATFORM is not set -CONFIG_USE_OF=y -# CONFIG_VFP is not set -CONFIG_WATCHDOG_CORE=y -# CONFIG_WQ_POWER_EFFICIENT_DEFAULT is not set -CONFIG_XPS=y -CONFIG_XXHASH=y -CONFIG_XZ_DEC_ARM=y -CONFIG_XZ_DEC_BCJ=y -CONFIG_ZBOOT_ROM_BSS=0 -CONFIG_ZBOOT_ROM_TEXT=0 -CONFIG_ZLIB_DEFLATE=y -CONFIG_ZLIB_INFLATE=y -CONFIG_ZSTD_COMPRESS=y -CONFIG_ZSTD_DECOMPRESS=y diff --git a/target/linux/mediatek/patches-5.15/041-block-fit-partition-parser.patch b/target/linux/mediatek/patches-5.15/041-block-fit-partition-parser.patch deleted file mode 100644 index 13a16b6fa0..0000000000 --- a/target/linux/mediatek/patches-5.15/041-block-fit-partition-parser.patch +++ /dev/null @@ -1,214 +0,0 @@ -From 69357074558daf6ff24c9f58714935e9e095a865 Mon Sep 17 00:00:00 2001 -From: OpenWrt community -Date: Wed, 13 Jul 2022 13:37:33 +0200 -Subject: [PATCH] kernel: add block fit partition parser - ---- - block/blk.h | 2 ++ - block/partitions/Kconfig | 7 +++++++ - block/partitions/Makefile | 1 + - block/partitions/check.h | 3 +++ - block/partitions/core.c | 17 +++++++++++++++++ - block/partitions/efi.c | 8 ++++++++ - block/partitions/efi.h | 3 +++ - block/partitions/msdos.c | 10 ++++++++++ - drivers/mtd/mtd_blkdevs.c | 2 ++ - drivers/mtd/ubi/block.c | 3 +++ - include/linux/msdos_partition.h | 1 + - 11 files changed, 57 insertions(+) - ---- a/block/blk.h -+++ b/block/blk.h -@@ -354,6 +354,8 @@ void blk_free_ext_minor(unsigned int min - #define ADDPART_FLAG_NONE 0 - #define ADDPART_FLAG_RAID 1 - #define ADDPART_FLAG_WHOLEDISK 2 -+#define ADDPART_FLAG_READONLY 4 -+#define ADDPART_FLAG_ROOTDEV 8 - int bdev_add_partition(struct gendisk *disk, int partno, sector_t start, - sector_t length); - int bdev_del_partition(struct gendisk *disk, int partno); ---- a/block/partitions/Kconfig -+++ b/block/partitions/Kconfig -@@ -101,6 +101,13 @@ config ATARI_PARTITION - Say Y here if you would like to use hard disks under Linux which - were partitioned under the Atari OS. - -+config FIT_PARTITION -+ bool "Flattened-Image-Tree (FIT) partition support" if PARTITION_ADVANCED -+ default n -+ help -+ Say Y here if your system needs to mount the filesystem part of -+ a Flattened-Image-Tree (FIT) image commonly used with Das U-Boot. -+ - config IBM_PARTITION - bool "IBM disk label and partition support" - depends on PARTITION_ADVANCED && S390 ---- a/block/partitions/Makefile -+++ b/block/partitions/Makefile -@@ -8,6 +8,7 @@ obj-$(CONFIG_ACORN_PARTITION) += acorn.o - obj-$(CONFIG_AMIGA_PARTITION) += amiga.o - obj-$(CONFIG_ATARI_PARTITION) += atari.o - obj-$(CONFIG_AIX_PARTITION) += aix.o -+obj-$(CONFIG_FIT_PARTITION) += fit.o - obj-$(CONFIG_CMDLINE_PARTITION) += cmdline.o - obj-$(CONFIG_MAC_PARTITION) += mac.o - obj-$(CONFIG_LDM_PARTITION) += ldm.o ---- a/block/partitions/check.h -+++ b/block/partitions/check.h -@@ -58,6 +58,7 @@ int amiga_partition(struct parsed_partit - int atari_partition(struct parsed_partitions *state); - int cmdline_partition(struct parsed_partitions *state); - int efi_partition(struct parsed_partitions *state); -+int fit_partition(struct parsed_partitions *state); - int ibm_partition(struct parsed_partitions *); - int karma_partition(struct parsed_partitions *state); - int ldm_partition(struct parsed_partitions *state); -@@ -68,3 +69,5 @@ int sgi_partition(struct parsed_partitio - int sun_partition(struct parsed_partitions *state); - int sysv68_partition(struct parsed_partitions *state); - int ultrix_partition(struct parsed_partitions *state); -+ -+int parse_fit_partitions(struct parsed_partitions *state, u64 start_sector, u64 nr_sectors, int *slot, int add_remain); ---- a/block/partitions/core.c -+++ b/block/partitions/core.c -@@ -12,6 +12,10 @@ - #include - #include - #include -+#ifdef CONFIG_FIT_PARTITION -+#include -+#endif -+ - #include "check.h" - - static int (*check_part[])(struct parsed_partitions *) = { -@@ -48,6 +52,9 @@ static int (*check_part[])(struct parsed - #ifdef CONFIG_EFI_PARTITION - efi_partition, /* this must come before msdos */ - #endif -+#ifdef CONFIG_FIT_PARTITION -+ fit_partition, -+#endif - #ifdef CONFIG_SGI_PARTITION - sgi_partition, - #endif -@@ -408,6 +415,11 @@ static struct block_device *add_partitio - goto out_del; - } - -+#ifdef CONFIG_FIT_PARTITION -+ if (flags & ADDPART_FLAG_READONLY) -+ bdev->bd_read_only = true; -+#endif -+ - /* everything is up and running, commence */ - err = xa_insert(&disk->part_tbl, partno, bdev, GFP_KERNEL); - if (err) -@@ -595,6 +607,11 @@ static bool blk_add_partition(struct gen - (state->parts[p].flags & ADDPART_FLAG_RAID)) - md_autodetect_dev(part->bd_dev); - -+#ifdef CONFIG_FIT_PARTITION -+ if ((state->parts[p].flags & ADDPART_FLAG_ROOTDEV) && ROOT_DEV == 0) -+ ROOT_DEV = part->bd_dev; -+#endif -+ - return true; - } - ---- a/block/partitions/efi.c -+++ b/block/partitions/efi.c -@@ -716,6 +716,9 @@ int efi_partition(struct parsed_partitio - gpt_entry *ptes = NULL; - u32 i; - unsigned ssz = queue_logical_block_size(state->disk->queue) / 512; -+#ifdef CONFIG_FIT_PARTITION -+ u32 extra_slot = 64; -+#endif - - if (!find_valid_gpt(state, &gpt, &ptes) || !gpt || !ptes) { - kfree(gpt); -@@ -749,6 +752,11 @@ int efi_partition(struct parsed_partitio - ARRAY_SIZE(ptes[i].partition_name)); - utf16_le_to_7bit(ptes[i].partition_name, label_max, info->volname); - state->parts[i + 1].has_info = true; -+#ifdef CONFIG_FIT_PARTITION -+ /* If this is a U-Boot FIT volume it may have subpartitions */ -+ if (!efi_guidcmp(ptes[i].partition_type_guid, PARTITION_LINUX_FIT_GUID)) -+ (void) parse_fit_partitions(state, start * ssz, size * ssz, &extra_slot, 1); -+#endif - } - kfree(ptes); - kfree(gpt); ---- a/block/partitions/efi.h -+++ b/block/partitions/efi.h -@@ -52,6 +52,9 @@ - #define PARTITION_LINUX_LVM_GUID \ - EFI_GUID( 0xe6d6d379, 0xf507, 0x44c2, \ - 0xa2, 0x3c, 0x23, 0x8f, 0x2a, 0x3d, 0xf9, 0x28) -+#define PARTITION_LINUX_FIT_GUID \ -+ EFI_GUID( 0xcae9be83, 0xb15f, 0x49cc, \ -+ 0x86, 0x3f, 0x08, 0x1b, 0x74, 0x4a, 0x2d, 0x93) - - typedef struct _gpt_header { - __le64 signature; ---- a/block/partitions/msdos.c -+++ b/block/partitions/msdos.c -@@ -564,6 +564,15 @@ static void parse_minix(struct parsed_pa - #endif /* CONFIG_MINIX_SUBPARTITION */ - } - -+static void parse_fit_mbr(struct parsed_partitions *state, -+ sector_t offset, sector_t size, int origin) -+{ -+#ifdef CONFIG_FIT_PARTITION -+ u32 extra_slot = 64; -+ (void) parse_fit_partitions(state, offset, size, &extra_slot, 1); -+#endif /* CONFIG_FIT_PARTITION */ -+} -+ - static struct { - unsigned char id; - void (*parse)(struct parsed_partitions *, sector_t, sector_t, int); -@@ -575,6 +584,7 @@ static struct { - {UNIXWARE_PARTITION, parse_unixware}, - {SOLARIS_X86_PARTITION, parse_solaris_x86}, - {NEW_SOLARIS_X86_PARTITION, parse_solaris_x86}, -+ {FIT_PARTITION, parse_fit_mbr}, - {0, NULL}, - }; - ---- a/drivers/mtd/mtd_blkdevs.c -+++ b/drivers/mtd/mtd_blkdevs.c -@@ -345,6 +345,8 @@ int add_mtd_blktrans_dev(struct mtd_blkt - gd->first_minor = (new->devnum) << tr->part_bits; - gd->minors = 1 << tr->part_bits; - gd->fops = &mtd_block_ops; -+ if (IS_ENABLED(CONFIG_FIT_PARTITION) && !mtd_type_is_nand(new->mtd)) -+ gd->flags |= GENHD_FL_EXT_DEVT; - - if (tr->part_bits) - if (new->devnum < 26) ---- a/drivers/mtd/ubi/block.c -+++ b/drivers/mtd/ubi/block.c -@@ -428,6 +428,9 @@ int ubiblock_create(struct ubi_volume_in - goto out_cleanup_disk; - } - gd->private_data = dev; -+#ifdef CONFIG_FIT_PARTITION -+ gd->flags |= GENHD_FL_EXT_DEVT; -+#endif - sprintf(gd->disk_name, "ubiblock%d_%d", dev->ubi_num, dev->vol_id); - set_capacity(gd, disk_capacity); - dev->gd = gd; ---- a/include/linux/msdos_partition.h -+++ b/include/linux/msdos_partition.h -@@ -31,6 +31,7 @@ enum msdos_sys_ind { - LINUX_LVM_PARTITION = 0x8e, - LINUX_RAID_PARTITION = 0xfd, /* autodetect RAID partition */ - -+ FIT_PARTITION = 0x2e, /* U-Boot uImage.FIT */ - SOLARIS_X86_PARTITION = 0x82, /* also Linux swap partitions */ - NEW_SOLARIS_X86_PARTITION = 0xbf, - diff --git a/target/linux/mediatek/patches-5.15/100-dts-update-mt7622-rfb1.patch b/target/linux/mediatek/patches-5.15/100-dts-update-mt7622-rfb1.patch deleted file mode 100644 index 1f9e24a4d2..0000000000 --- a/target/linux/mediatek/patches-5.15/100-dts-update-mt7622-rfb1.patch +++ /dev/null @@ -1,119 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts -+++ b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts -@@ -1,7 +1,6 @@ - /* -- * Copyright (c) 2017 MediaTek Inc. -- * Author: Ming Huang -- * Sean Wang -+ * Copyright (c) 2018 MediaTek Inc. -+ * Author: Ryder Lee - * - * SPDX-License-Identifier: (GPL-2.0 OR MIT) - */ -@@ -23,7 +22,7 @@ - - chosen { - stdout-path = "serial0:115200n8"; -- bootargs = "earlycon=uart8250,mmio32,0x11002000 swiotlb=512"; -+ bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n1 swiotlb=512"; - }; - - cpus { -@@ -40,23 +39,22 @@ - - gpio-keys { - compatible = "gpio-keys"; -- poll-interval = <100>; - - factory { - label = "factory"; - linux,code = ; -- gpios = <&pio 0 0>; -+ gpios = <&pio 0 GPIO_ACTIVE_LOW>; - }; - - wps { - label = "wps"; - linux,code = ; -- gpios = <&pio 102 0>; -+ gpios = <&pio 102 GPIO_ACTIVE_LOW>; - }; - }; - - memory@40000000 { -- reg = <0 0x40000000 0 0x20000000>; -+ reg = <0 0x40000000 0 0x40000000>; - }; - - reg_1p8v: regulator-1p8v { -@@ -132,22 +130,22 @@ - - port@0 { - reg = <0>; -- label = "lan0"; -+ label = "lan1"; - }; - - port@1 { - reg = <1>; -- label = "lan1"; -+ label = "lan2"; - }; - - port@2 { - reg = <2>; -- label = "lan2"; -+ label = "lan3"; - }; - - port@3 { - reg = <3>; -- label = "lan3"; -+ label = "lan4"; - }; - - port@4 { -@@ -236,15 +234,28 @@ - - &pcie { - pinctrl-names = "default"; -- pinctrl-0 = <&pcie0_pins>; -+ pinctrl-0 = <&pcie0_pins>, <&pcie1_pins>; - status = "okay"; - - pcie@0,0 { - status = "okay"; - }; -+ -+ pcie@1,0 { -+ status = "okay"; -+ }; - }; - - &pio { -+ /* Attention: GPIO 90 is used to switch between PCIe@1,0 and -+ * SATA functions. i.e. output-high: PCIe, output-low: SATA -+ */ -+ asm_sel { -+ gpio-hog; -+ gpios = <90 GPIO_ACTIVE_HIGH>; -+ output-high; -+ }; -+ - /* eMMC is shared pin with parallel NAND */ - emmc_pins_default: emmc-pins-default { - mux { -@@ -521,11 +532,11 @@ - }; - - &sata { -- status = "okay"; -+ status = "disabled"; - }; - - &sata_phy { -- status = "okay"; -+ status = "disabled"; - }; - - &spi0 { diff --git a/target/linux/mediatek/patches-5.15/101-dts-update-mt7629-rfb.patch b/target/linux/mediatek/patches-5.15/101-dts-update-mt7629-rfb.patch deleted file mode 100644 index 254b5f9eb7..0000000000 --- a/target/linux/mediatek/patches-5.15/101-dts-update-mt7629-rfb.patch +++ /dev/null @@ -1,60 +0,0 @@ ---- a/arch/arm/boot/dts/mt7629-rfb.dts -+++ b/arch/arm/boot/dts/mt7629-rfb.dts -@@ -18,6 +18,7 @@ - - chosen { - stdout-path = "serial0:115200n8"; -+ bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n8"; - }; - - gpio-keys { -@@ -70,6 +71,10 @@ - compatible = "mediatek,eth-mac"; - reg = <0>; - phy-mode = "2500base-x"; -+ -+ nvmem-cells = <&macaddr_factory_2a>; -+ nvmem-cell-names = "mac-address"; -+ - fixed-link { - speed = <2500>; - full-duplex; -@@ -82,6 +87,9 @@ - reg = <1>; - phy-mode = "gmii"; - phy-handle = <&phy0>; -+ -+ nvmem-cells = <&macaddr_factory_24>; -+ nvmem-cell-names = "mac-address"; - }; - - mdio: mdio-bus { -@@ -133,8 +141,9 @@ - }; - - partition@b0000 { -- label = "kernel"; -+ label = "firmware"; - reg = <0xb0000 0xb50000>; -+ compatible = "denx,fit"; - }; - }; - }; -@@ -272,3 +281,17 @@ - pinctrl-0 = <&watchdog_pins>; - status = "okay"; - }; -+ -+&factory { -+ compatible = "nvmem-cells"; -+ #address-cells = <1>; -+ #size-cells = <1>; -+ -+ macaddr_factory_24: macaddr@24 { -+ reg = <0x24 0x6>; -+ }; -+ -+ macaddr_factory_2a: macaddr@2a { -+ reg = <0x2a 0x6>; -+ }; -+}; diff --git a/target/linux/mediatek/patches-5.15/103-mt7623-enable-arch-timer.patch b/target/linux/mediatek/patches-5.15/103-mt7623-enable-arch-timer.patch deleted file mode 100644 index 04df7b927b..0000000000 --- a/target/linux/mediatek/patches-5.15/103-mt7623-enable-arch-timer.patch +++ /dev/null @@ -1,20 +0,0 @@ -From d6a596012150960f0f3a214d31bbac4b607dbd1e Mon Sep 17 00:00:00 2001 -From: Chuanhong Guo -Date: Fri, 29 Apr 2022 10:40:56 +0800 -Subject: [PATCH] arm: mediatek: select arch timer for mt7623 - -Signed-off-by: Chuanhong Guo ---- - arch/arm/mach-mediatek/Kconfig | 1 + - 1 file changed, 1 insertion(+) - ---- a/arch/arm/mach-mediatek/Kconfig -+++ b/arch/arm/mach-mediatek/Kconfig -@@ -26,6 +26,7 @@ config MACH_MT6592 - config MACH_MT7623 - bool "MediaTek MT7623 SoCs support" - default ARCH_MEDIATEK -+ select HAVE_ARM_ARCH_TIMER - - config MACH_MT7629 - bool "MediaTek MT7629 SoCs support" diff --git a/target/linux/mediatek/patches-5.15/104-mt7622-add-snor-irq.patch b/target/linux/mediatek/patches-5.15/104-mt7622-add-snor-irq.patch deleted file mode 100644 index 79b051147a..0000000000 --- a/target/linux/mediatek/patches-5.15/104-mt7622-add-snor-irq.patch +++ /dev/null @@ -1,10 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi -@@ -559,6 +559,7 @@ - compatible = "mediatek,mt7622-nor", - "mediatek,mt8173-nor"; - reg = <0 0x11014000 0 0xe0>; -+ interrupts = ; - clocks = <&pericfg CLK_PERI_FLASH_PD>, - <&topckgen CLK_TOP_FLASH_SEL>; - clock-names = "spi", "sf"; diff --git a/target/linux/mediatek/patches-5.15/105-dts-mt7622-enable-pstore.patch b/target/linux/mediatek/patches-5.15/105-dts-mt7622-enable-pstore.patch deleted file mode 100644 index da42c07728..0000000000 --- a/target/linux/mediatek/patches-5.15/105-dts-mt7622-enable-pstore.patch +++ /dev/null @@ -1,25 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi -@@ -111,7 +111,7 @@ - }; - - psci { -- compatible = "arm,psci-0.2"; -+ compatible = "arm,psci-1.0"; - method = "smc"; - }; - -@@ -127,6 +127,13 @@ - #size-cells = <2>; - ranges; - -+ /* 64 KiB reserved for ramoops/pstore */ -+ ramoops@42ff0000 { -+ compatible = "ramoops"; -+ reg = <0 0x42ff0000 0 0x10000>; -+ record-size = <0x1000>; -+ }; -+ - /* 192 KiB reserved for ARM Trusted Firmware (BL31) */ - secmon_reserved: secmon@43000000 { - reg = <0 0x43000000 0 0x30000>; diff --git a/target/linux/mediatek/patches-5.15/110-dts-fix-bpi2-console.patch b/target/linux/mediatek/patches-5.15/110-dts-fix-bpi2-console.patch deleted file mode 100644 index 8dc53d2985..0000000000 --- a/target/linux/mediatek/patches-5.15/110-dts-fix-bpi2-console.patch +++ /dev/null @@ -1,10 +0,0 @@ ---- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts -+++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts -@@ -19,6 +19,7 @@ - - chosen { - stdout-path = "serial2:115200n8"; -+ bootargs = "console=ttyS2,115200n8 console=tty1"; - }; - - connector { diff --git a/target/linux/mediatek/patches-5.15/111-dts-fix-bpi64-console.patch b/target/linux/mediatek/patches-5.15/111-dts-fix-bpi64-console.patch deleted file mode 100644 index 07a2eae245..0000000000 --- a/target/linux/mediatek/patches-5.15/111-dts-fix-bpi64-console.patch +++ /dev/null @@ -1,11 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -@@ -22,7 +22,7 @@ - - chosen { - stdout-path = "serial0:115200n8"; -- bootargs = "earlycon=uart8250,mmio32,0x11002000 swiotlb=512"; -+ bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n1 swiotlb=512"; - }; - - cpus { diff --git a/target/linux/mediatek/patches-5.15/112-dts-fix-bpi64-lan-names.patch b/target/linux/mediatek/patches-5.15/112-dts-fix-bpi64-lan-names.patch deleted file mode 100644 index 6ce85efde9..0000000000 --- a/target/linux/mediatek/patches-5.15/112-dts-fix-bpi64-lan-names.patch +++ /dev/null @@ -1,37 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -@@ -18,6 +18,7 @@ - - aliases { - serial0 = &uart0; -+ ethernet0 = &gmac0; - }; - - chosen { -@@ -160,22 +161,22 @@ - - port@1 { - reg = <1>; -- label = "lan0"; -+ label = "lan1"; - }; - - port@2 { - reg = <2>; -- label = "lan1"; -+ label = "lan2"; - }; - - port@3 { - reg = <3>; -- label = "lan2"; -+ label = "lan3"; - }; - - port@4 { - reg = <4>; -- label = "lan3"; -+ label = "lan4"; - }; - - port@6 { diff --git a/target/linux/mediatek/patches-5.15/113-dts-fix-bpi64-leds-and-buttons.patch b/target/linux/mediatek/patches-5.15/113-dts-fix-bpi64-leds-and-buttons.patch deleted file mode 100644 index f728b96564..0000000000 --- a/target/linux/mediatek/patches-5.15/113-dts-fix-bpi64-leds-and-buttons.patch +++ /dev/null @@ -1,56 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -@@ -19,6 +19,10 @@ - aliases { - serial0 = &uart0; - ethernet0 = &gmac0; -+ led-boot = &led_system_green; -+ led-failsafe = &led_system_blue; -+ led-running = &led_system_green; -+ led-upgrade = &led_system_blue; - }; - - chosen { -@@ -42,8 +46,8 @@ - compatible = "gpio-keys"; - - factory { -- label = "factory"; -- linux,code = ; -+ label = "reset"; -+ linux,code = ; - gpios = <&pio 0 GPIO_ACTIVE_HIGH>; - }; - -@@ -57,17 +61,25 @@ - leds { - compatible = "gpio-leds"; - -- green { -- label = "bpi-r64:pio:green"; -- gpios = <&pio 89 GPIO_ACTIVE_HIGH>; -+ led_system_blue: blue { -+ label = "bpi-r64:pio:blue"; -+ gpios = <&pio 85 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - -- red { -- label = "bpi-r64:pio:red"; -- gpios = <&pio 88 GPIO_ACTIVE_HIGH>; -+ led_system_green: green { -+ label = "bpi-r64:pio:green"; -+ gpios = <&pio 89 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; -+ -+/* -+ * red { -+ * label = "bpi-r64:pio:red"; -+ * gpios = <&pio 88 GPIO_ACTIVE_HIGH>; -+ * default-state = "off"; -+ * }; -+ */ - }; - - memory@40000000 { diff --git a/target/linux/mediatek/patches-5.15/114-dts-bpi64-disable-rtc.patch b/target/linux/mediatek/patches-5.15/114-dts-bpi64-disable-rtc.patch deleted file mode 100644 index 1f41142aac..0000000000 --- a/target/linux/mediatek/patches-5.15/114-dts-bpi64-disable-rtc.patch +++ /dev/null @@ -1,21 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -@@ -564,12 +564,16 @@ - status = "okay"; - }; - -+&rtc { -+ status = "disabled"; -+}; -+ - &sata { -- status = "disable"; -+ status = "disabled"; - }; - - &sata_phy { -- status = "disable"; -+ status = "disabled"; - }; - - &spi0 { diff --git a/target/linux/mediatek/patches-5.15/115-dts-bpi64-add-snand-support.patch b/target/linux/mediatek/patches-5.15/115-dts-bpi64-add-snand-support.patch deleted file mode 100644 index 34539a5d10..0000000000 --- a/target/linux/mediatek/patches-5.15/115-dts-bpi64-add-snand-support.patch +++ /dev/null @@ -1,50 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -@@ -259,14 +259,42 @@ - status = "disabled"; - }; - --&nor_flash { -- pinctrl-names = "default"; -- pinctrl-0 = <&spi_nor_pins>; -- status = "disabled"; -+&bch { -+ status = "okay"; -+}; - -+&snfi { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&serial_nand_pins>; -+ status = "okay"; - flash@0 { -- compatible = "jedec,spi-nor"; -+ compatible = "spi-nand"; - reg = <0>; -+ spi-tx-bus-width = <4>; -+ spi-rx-bus-width = <4>; -+ nand-ecc-engine = <&snfi>; -+ partitions { -+ compatible = "fixed-partitions"; -+ #address-cells = <1>; -+ #size-cells = <1>; -+ -+ partition@0 { -+ label = "bl2"; -+ reg = <0x0 0x80000>; -+ read-only; -+ }; -+ -+ partition@80000 { -+ label = "fip"; -+ reg = <0x80000 0x200000>; -+ read-only; -+ }; -+ -+ partition@280000 { -+ label = "ubi"; -+ reg = <0x280000 0x7d80000>; -+ }; -+ }; - }; - }; - diff --git a/target/linux/mediatek/patches-5.15/120-01-v5.18-mtd-nand-ecc-Add-infrastructure-to-support-hardware-.patch b/target/linux/mediatek/patches-5.15/120-01-v5.18-mtd-nand-ecc-Add-infrastructure-to-support-hardware-.patch deleted file mode 100644 index 7fb62e7403..0000000000 --- a/target/linux/mediatek/patches-5.15/120-01-v5.18-mtd-nand-ecc-Add-infrastructure-to-support-hardware-.patch +++ /dev/null @@ -1,214 +0,0 @@ -From ad4944aa0b02cb043afe20bc2a018c161e65c992 Mon Sep 17 00:00:00 2001 -From: Miquel Raynal -Date: Thu, 16 Dec 2021 12:16:38 +0100 -Subject: [PATCH 01/15] mtd: nand: ecc: Add infrastructure to support hardware - engines - -Add the necessary helpers to register/unregister hardware ECC engines -that will be called from ECC engine drivers. - -Also add helpers to get the right engine from the user -perspective. Keep a reference of the in use ECC engine in order to -prevent modules to be unloaded. Put the reference when the engine gets -retired. - -A static list of hardware (only) ECC engines is setup to keep track of -the registered engines. - -Signed-off-by: Miquel Raynal -Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-13-miquel.raynal@bootlin.com -(cherry picked from commit 96489c1c0b53131b0e1ec33e2060538379ad6152) ---- - drivers/mtd/nand/core.c | 10 +++-- - drivers/mtd/nand/ecc.c | 88 ++++++++++++++++++++++++++++++++++++++++ - include/linux/mtd/nand.h | 28 +++++++++++++ - 3 files changed, 123 insertions(+), 3 deletions(-) - ---- a/drivers/mtd/nand/core.c -+++ b/drivers/mtd/nand/core.c -@@ -232,7 +232,9 @@ static int nanddev_get_ecc_engine(struct - nand->ecc.engine = nand_ecc_get_on_die_hw_engine(nand); - break; - case NAND_ECC_ENGINE_TYPE_ON_HOST: -- pr_err("On-host hardware ECC engines not supported yet\n"); -+ nand->ecc.engine = nand_ecc_get_on_host_hw_engine(nand); -+ if (PTR_ERR(nand->ecc.engine) == -EPROBE_DEFER) -+ return -EPROBE_DEFER; - break; - default: - pr_err("Missing ECC engine type\n"); -@@ -252,7 +254,7 @@ static int nanddev_put_ecc_engine(struct - { - switch (nand->ecc.ctx.conf.engine_type) { - case NAND_ECC_ENGINE_TYPE_ON_HOST: -- pr_err("On-host hardware ECC engines not supported yet\n"); -+ nand_ecc_put_on_host_hw_engine(nand); - break; - case NAND_ECC_ENGINE_TYPE_NONE: - case NAND_ECC_ENGINE_TYPE_SOFT: -@@ -297,7 +299,9 @@ int nanddev_ecc_engine_init(struct nand_ - /* Look for the ECC engine to use */ - ret = nanddev_get_ecc_engine(nand); - if (ret) { -- pr_err("No ECC engine found\n"); -+ if (ret != -EPROBE_DEFER) -+ pr_err("No ECC engine found\n"); -+ - return ret; - } - ---- a/drivers/mtd/nand/ecc.c -+++ b/drivers/mtd/nand/ecc.c -@@ -96,6 +96,12 @@ - #include - #include - #include -+#include -+#include -+#include -+ -+static LIST_HEAD(on_host_hw_engines); -+static DEFINE_MUTEX(on_host_hw_engines_mutex); - - /** - * nand_ecc_init_ctx - Init the ECC engine context -@@ -611,6 +617,88 @@ struct nand_ecc_engine *nand_ecc_get_on_ - } - EXPORT_SYMBOL(nand_ecc_get_on_die_hw_engine); - -+int nand_ecc_register_on_host_hw_engine(struct nand_ecc_engine *engine) -+{ -+ struct nand_ecc_engine *item; -+ -+ if (!engine) -+ return -EINVAL; -+ -+ /* Prevent multiple registrations of one engine */ -+ list_for_each_entry(item, &on_host_hw_engines, node) -+ if (item == engine) -+ return 0; -+ -+ mutex_lock(&on_host_hw_engines_mutex); -+ list_add_tail(&engine->node, &on_host_hw_engines); -+ mutex_unlock(&on_host_hw_engines_mutex); -+ -+ return 0; -+} -+EXPORT_SYMBOL(nand_ecc_register_on_host_hw_engine); -+ -+int nand_ecc_unregister_on_host_hw_engine(struct nand_ecc_engine *engine) -+{ -+ if (!engine) -+ return -EINVAL; -+ -+ mutex_lock(&on_host_hw_engines_mutex); -+ list_del(&engine->node); -+ mutex_unlock(&on_host_hw_engines_mutex); -+ -+ return 0; -+} -+EXPORT_SYMBOL(nand_ecc_unregister_on_host_hw_engine); -+ -+static struct nand_ecc_engine *nand_ecc_match_on_host_hw_engine(struct device *dev) -+{ -+ struct nand_ecc_engine *item; -+ -+ list_for_each_entry(item, &on_host_hw_engines, node) -+ if (item->dev == dev) -+ return item; -+ -+ return NULL; -+} -+ -+struct nand_ecc_engine *nand_ecc_get_on_host_hw_engine(struct nand_device *nand) -+{ -+ struct nand_ecc_engine *engine = NULL; -+ struct device *dev = &nand->mtd.dev; -+ struct platform_device *pdev; -+ struct device_node *np; -+ -+ if (list_empty(&on_host_hw_engines)) -+ return NULL; -+ -+ /* Check for an explicit nand-ecc-engine property */ -+ np = of_parse_phandle(dev->of_node, "nand-ecc-engine", 0); -+ if (np) { -+ pdev = of_find_device_by_node(np); -+ if (!pdev) -+ return ERR_PTR(-EPROBE_DEFER); -+ -+ engine = nand_ecc_match_on_host_hw_engine(&pdev->dev); -+ platform_device_put(pdev); -+ of_node_put(np); -+ -+ if (!engine) -+ return ERR_PTR(-EPROBE_DEFER); -+ } -+ -+ if (engine) -+ get_device(engine->dev); -+ -+ return engine; -+} -+EXPORT_SYMBOL(nand_ecc_get_on_host_hw_engine); -+ -+void nand_ecc_put_on_host_hw_engine(struct nand_device *nand) -+{ -+ put_device(nand->ecc.engine->dev); -+} -+EXPORT_SYMBOL(nand_ecc_put_on_host_hw_engine); -+ - MODULE_LICENSE("GPL"); - MODULE_AUTHOR("Miquel Raynal "); - MODULE_DESCRIPTION("Generic ECC engine"); ---- a/include/linux/mtd/nand.h -+++ b/include/linux/mtd/nand.h -@@ -264,11 +264,35 @@ struct nand_ecc_engine_ops { - }; - - /** -+ * enum nand_ecc_engine_integration - How the NAND ECC engine is integrated -+ * @NAND_ECC_ENGINE_INTEGRATION_INVALID: Invalid value -+ * @NAND_ECC_ENGINE_INTEGRATION_PIPELINED: Pipelined engine, performs on-the-fly -+ * correction, does not need to copy -+ * data around -+ * @NAND_ECC_ENGINE_INTEGRATION_EXTERNAL: External engine, needs to bring the -+ * data into its own area before use -+ */ -+enum nand_ecc_engine_integration { -+ NAND_ECC_ENGINE_INTEGRATION_INVALID, -+ NAND_ECC_ENGINE_INTEGRATION_PIPELINED, -+ NAND_ECC_ENGINE_INTEGRATION_EXTERNAL, -+}; -+ -+/** - * struct nand_ecc_engine - ECC engine abstraction for NAND devices -+ * @dev: Host device -+ * @node: Private field for registration time - * @ops: ECC engine operations -+ * @integration: How the engine is integrated with the host -+ * (only relevant on %NAND_ECC_ENGINE_TYPE_ON_HOST engines) -+ * @priv: Private data - */ - struct nand_ecc_engine { -+ struct device *dev; -+ struct list_head node; - struct nand_ecc_engine_ops *ops; -+ enum nand_ecc_engine_integration integration; -+ void *priv; - }; - - void of_get_nand_ecc_user_config(struct nand_device *nand); -@@ -279,8 +303,12 @@ int nand_ecc_prepare_io_req(struct nand_ - int nand_ecc_finish_io_req(struct nand_device *nand, - struct nand_page_io_req *req); - bool nand_ecc_is_strong_enough(struct nand_device *nand); -+int nand_ecc_register_on_host_hw_engine(struct nand_ecc_engine *engine); -+int nand_ecc_unregister_on_host_hw_engine(struct nand_ecc_engine *engine); - struct nand_ecc_engine *nand_ecc_get_sw_engine(struct nand_device *nand); - struct nand_ecc_engine *nand_ecc_get_on_die_hw_engine(struct nand_device *nand); -+struct nand_ecc_engine *nand_ecc_get_on_host_hw_engine(struct nand_device *nand); -+void nand_ecc_put_on_host_hw_engine(struct nand_device *nand); - - #if IS_ENABLED(CONFIG_MTD_NAND_ECC_SW_HAMMING) - struct nand_ecc_engine *nand_ecc_sw_hamming_get_engine(void); diff --git a/target/linux/mediatek/patches-5.15/120-02-v5.18-mtd-nand-Add-a-new-helper-to-retrieve-the-ECC-contex.patch b/target/linux/mediatek/patches-5.15/120-02-v5.18-mtd-nand-Add-a-new-helper-to-retrieve-the-ECC-contex.patch deleted file mode 100644 index 61a39ee0e5..0000000000 --- a/target/linux/mediatek/patches-5.15/120-02-v5.18-mtd-nand-Add-a-new-helper-to-retrieve-the-ECC-contex.patch +++ /dev/null @@ -1,31 +0,0 @@ -From 840b2f8dd2d0579e517140e1f9bbc482eaf4ed07 Mon Sep 17 00:00:00 2001 -From: Miquel Raynal -Date: Thu, 16 Dec 2021 12:16:39 +0100 -Subject: [PATCH 02/15] mtd: nand: Add a new helper to retrieve the ECC context - -Introduce nand_to_ecc_ctx() which will allow to easily jump to the -private pointer of an ECC context given a NAND device. This is very -handy, from the prepare or finish ECC hook, to get the internal context -out of the NAND device object. - -Signed-off-by: Miquel Raynal -Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-14-miquel.raynal@bootlin.com -(cherry picked from commit cda32a618debd3fad8e42757b198719ae180f8f4) ---- - include/linux/mtd/nand.h | 5 +++++ - 1 file changed, 5 insertions(+) - ---- a/include/linux/mtd/nand.h -+++ b/include/linux/mtd/nand.h -@@ -990,6 +990,11 @@ int nanddev_markbad(struct nand_device * - int nanddev_ecc_engine_init(struct nand_device *nand); - void nanddev_ecc_engine_cleanup(struct nand_device *nand); - -+static inline void *nand_to_ecc_ctx(struct nand_device *nand) -+{ -+ return nand->ecc.ctx.priv; -+} -+ - /* BBT related functions */ - enum nand_bbt_block_status { - NAND_BBT_BLOCK_STATUS_UNKNOWN, diff --git a/target/linux/mediatek/patches-5.15/120-03-v5.18-mtd-nand-ecc-Provide-a-helper-to-retrieve-a-pileline.patch b/target/linux/mediatek/patches-5.15/120-03-v5.18-mtd-nand-ecc-Provide-a-helper-to-retrieve-a-pileline.patch deleted file mode 100644 index 29b62880ab..0000000000 --- a/target/linux/mediatek/patches-5.15/120-03-v5.18-mtd-nand-ecc-Provide-a-helper-to-retrieve-a-pileline.patch +++ /dev/null @@ -1,73 +0,0 @@ -From 784866bc4f9f25e0494b77750f95af2a2619e498 Mon Sep 17 00:00:00 2001 -From: Miquel Raynal -Date: Thu, 16 Dec 2021 12:16:41 +0100 -Subject: [PATCH 03/15] mtd: nand: ecc: Provide a helper to retrieve a - pilelined engine device - -In a pipelined engine situation, we might either have the host which -internally has support for error correction, or have it using an -external hardware block for this purpose. In the former case, the host -is also the ECC engine. In the latter case, it is not. In order to get -the right pointers on the right devices (for example: in order to devm_* -allocate variables), let's introduce this helper which can safely be -called by pipelined ECC engines in order to retrieve the right device -structure. - -Signed-off-by: Miquel Raynal -Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-16-miquel.raynal@bootlin.com -(cherry picked from commit 5145abeb0649acf810a32e63bd762e617a9b3309) ---- - drivers/mtd/nand/ecc.c | 31 +++++++++++++++++++++++++++++++ - include/linux/mtd/nand.h | 1 + - 2 files changed, 32 insertions(+) - ---- a/drivers/mtd/nand/ecc.c -+++ b/drivers/mtd/nand/ecc.c -@@ -699,6 +699,37 @@ void nand_ecc_put_on_host_hw_engine(stru - } - EXPORT_SYMBOL(nand_ecc_put_on_host_hw_engine); - -+/* -+ * In the case of a pipelined engine, the device registering the ECC -+ * engine is not necessarily the ECC engine itself but may be a host controller. -+ * It is then useful to provide a helper to retrieve the right device object -+ * which actually represents the ECC engine. -+ */ -+struct device *nand_ecc_get_engine_dev(struct device *host) -+{ -+ struct platform_device *ecc_pdev; -+ struct device_node *np; -+ -+ /* -+ * If the device node contains this property, it means we need to follow -+ * it in order to get the right ECC engine device we are looking for. -+ */ -+ np = of_parse_phandle(host->of_node, "nand-ecc-engine", 0); -+ if (!np) -+ return host; -+ -+ ecc_pdev = of_find_device_by_node(np); -+ if (!ecc_pdev) { -+ of_node_put(np); -+ return NULL; -+ } -+ -+ platform_device_put(ecc_pdev); -+ of_node_put(np); -+ -+ return &ecc_pdev->dev; -+} -+ - MODULE_LICENSE("GPL"); - MODULE_AUTHOR("Miquel Raynal "); - MODULE_DESCRIPTION("Generic ECC engine"); ---- a/include/linux/mtd/nand.h -+++ b/include/linux/mtd/nand.h -@@ -309,6 +309,7 @@ struct nand_ecc_engine *nand_ecc_get_sw_ - struct nand_ecc_engine *nand_ecc_get_on_die_hw_engine(struct nand_device *nand); - struct nand_ecc_engine *nand_ecc_get_on_host_hw_engine(struct nand_device *nand); - void nand_ecc_put_on_host_hw_engine(struct nand_device *nand); -+struct device *nand_ecc_get_engine_dev(struct device *host); - - #if IS_ENABLED(CONFIG_MTD_NAND_ECC_SW_HAMMING) - struct nand_ecc_engine *nand_ecc_sw_hamming_get_engine(void); diff --git a/target/linux/mediatek/patches-5.15/120-04-v5.18-spi-spi-mem-Introduce-a-capability-structure.patch b/target/linux/mediatek/patches-5.15/120-04-v5.18-spi-spi-mem-Introduce-a-capability-structure.patch deleted file mode 100644 index 1e7f572dd6..0000000000 --- a/target/linux/mediatek/patches-5.15/120-04-v5.18-spi-spi-mem-Introduce-a-capability-structure.patch +++ /dev/null @@ -1,71 +0,0 @@ -From 3e45577e70cbf8fdc5c13033114989794a3797d5 Mon Sep 17 00:00:00 2001 -From: Miquel Raynal -Date: Thu, 27 Jan 2022 10:17:56 +0100 -Subject: [PATCH 04/15] spi: spi-mem: Introduce a capability structure - -Create a spi_controller_mem_caps structure and put it within the -spi_controller structure close to the spi_controller_mem_ops -strucure. So far the only field in this structure is the support for dtr -operations, but soon we will add another parameter. - -Also create a helper to parse the capabilities and check if the -requested capability has been set or not. - -Signed-off-by: Miquel Raynal -Reviewed-by: Pratyush Yadav -Reviewed-by: Boris Brezillon -Reviewed-by: Tudor Ambarus -Reviewed-by: Mark Brown -Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-2-miquel.raynal@bootlin.com -(cherry picked from commit 4a3cc7fb6e63bcfdedec25364738f1493345bd20) ---- - include/linux/spi/spi-mem.h | 11 +++++++++++ - include/linux/spi/spi.h | 3 +++ - 2 files changed, 14 insertions(+) - ---- a/include/linux/spi/spi-mem.h -+++ b/include/linux/spi/spi-mem.h -@@ -286,6 +286,17 @@ struct spi_controller_mem_ops { - }; - - /** -+ * struct spi_controller_mem_caps - SPI memory controller capabilities -+ * @dtr: Supports DTR operations -+ */ -+struct spi_controller_mem_caps { -+ bool dtr; -+}; -+ -+#define spi_mem_controller_is_capable(ctlr, cap) \ -+ ((ctlr)->mem_caps && (ctlr)->mem_caps->cap) -+ -+/** - * struct spi_mem_driver - SPI memory driver - * @spidrv: inherit from a SPI driver - * @probe: probe a SPI memory. Usually where detection/initialization takes ---- a/include/linux/spi/spi.h -+++ b/include/linux/spi/spi.h -@@ -23,6 +23,7 @@ struct software_node; - struct spi_controller; - struct spi_transfer; - struct spi_controller_mem_ops; -+struct spi_controller_mem_caps; - - /* - * INTERFACES between SPI master-side drivers and SPI slave protocol handlers, -@@ -419,6 +420,7 @@ extern struct spi_device *spi_new_ancill - * @mem_ops: optimized/dedicated operations for interactions with SPI memory. - * This field is optional and should only be implemented if the - * controller has native support for memory like operations. -+ * @mem_caps: controller capabilities for the handling of memory operations. - * @unprepare_message: undo any work done by prepare_message(). - * @slave_abort: abort the ongoing transfer request on an SPI slave controller - * @cs_gpios: LEGACY: array of GPIO descs to use as chip select lines; one per -@@ -643,6 +645,7 @@ struct spi_controller { - - /* Optimized handlers for SPI memory-like operations. */ - const struct spi_controller_mem_ops *mem_ops; -+ const struct spi_controller_mem_caps *mem_caps; - - /* gpio chip select */ - int *cs_gpios; diff --git a/target/linux/mediatek/patches-5.15/120-05-v5.18-spi-spi-mem-Check-the-controller-extra-capabilities.patch b/target/linux/mediatek/patches-5.15/120-05-v5.18-spi-spi-mem-Check-the-controller-extra-capabilities.patch deleted file mode 100644 index 9f01fdb835..0000000000 --- a/target/linux/mediatek/patches-5.15/120-05-v5.18-spi-spi-mem-Check-the-controller-extra-capabilities.patch +++ /dev/null @@ -1,51 +0,0 @@ -From c9cae7e1e5c87d0aa76b7bededa5191a0c8cf25a Mon Sep 17 00:00:00 2001 -From: Miquel Raynal -Date: Thu, 27 Jan 2022 10:17:57 +0100 -Subject: [PATCH 05/15] spi: spi-mem: Check the controller extra capabilities - -Controllers can now provide a spi-mem capabilities structure. Let's make -use of it in spi_mem_controller_default_supports_op(). As we want to -check for DTR operations as well as normal operations in a single -helper, let's pull the necessary checks from spi_mem_dtr_supports_op() -for now. - -However, because no controller provide these extra capabilities, this -change has no effect so far. - -Signed-off-by: Miquel Raynal -Reviewed-by: Pratyush Yadav -Reviewed-by: Boris Brezillon -Reviewed-by: Tudor Ambarus -Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-3-miquel.raynal@bootlin.com -(cherry picked from commit cb7e96ee81edaa48c67d84c14df2cbe464391c37) ---- - drivers/spi/spi-mem.c | 17 +++++++++++++---- - 1 file changed, 13 insertions(+), 4 deletions(-) - ---- a/drivers/spi/spi-mem.c -+++ b/drivers/spi/spi-mem.c -@@ -173,11 +173,20 @@ EXPORT_SYMBOL_GPL(spi_mem_dtr_supports_o - bool spi_mem_default_supports_op(struct spi_mem *mem, - const struct spi_mem_op *op) - { -- if (op->cmd.dtr || op->addr.dtr || op->dummy.dtr || op->data.dtr) -- return false; -+ struct spi_controller *ctlr = mem->spi->controller; -+ bool op_is_dtr = -+ op->cmd.dtr || op->addr.dtr || op->dummy.dtr || op->data.dtr; - -- if (op->cmd.nbytes != 1) -- return false; -+ if (op_is_dtr) { -+ if (!spi_mem_controller_is_capable(ctlr, dtr)) -+ return false; -+ -+ if (op->cmd.nbytes != 2) -+ return false; -+ } else { -+ if (op->cmd.nbytes != 1) -+ return false; -+ } - - return spi_mem_check_buswidth(mem, op); - } diff --git a/target/linux/mediatek/patches-5.15/120-06-v5.18-spi-spi-mem-Kill-the-spi_mem_dtr_supports_op-helper.patch b/target/linux/mediatek/patches-5.15/120-06-v5.18-spi-spi-mem-Kill-the-spi_mem_dtr_supports_op-helper.patch deleted file mode 100644 index c313a455b6..0000000000 --- a/target/linux/mediatek/patches-5.15/120-06-v5.18-spi-spi-mem-Kill-the-spi_mem_dtr_supports_op-helper.patch +++ /dev/null @@ -1,111 +0,0 @@ -From 2e5fba82e4aeb72d71230eef2541881615aaf7cf Mon Sep 17 00:00:00 2001 -From: Miquel Raynal -Date: Thu, 27 Jan 2022 10:18:00 +0100 -Subject: [PATCH 06/15] spi: spi-mem: Kill the spi_mem_dtr_supports_op() helper - -Now that spi_mem_default_supports_op() has access to the static -controller capabilities (relating to memory operations), and now that -these capabilities have been filled by the relevant controllers, there -is no need for a specific helper checking only DTR operations, so let's -just kill spi_mem_dtr_supports_op() and simply use -spi_mem_default_supports_op() instead. - -Signed-off-by: Miquel Raynal -Reviewed-by: Pratyush Yadav -Reviewed-by: Boris Brezillon -Reviewed-by: Tudor Ambarus -Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-6-miquel.raynal@bootlin.com -(cherry picked from commit 9a15efc5d5e6b5beaed0883e5bdcd0b1384c1b20) ---- - drivers/spi/spi-cadence-quadspi.c | 5 +---- - drivers/spi/spi-mem.c | 10 ---------- - drivers/spi/spi-mxic.c | 10 +--------- - include/linux/spi/spi-mem.h | 11 ----------- - 4 files changed, 2 insertions(+), 34 deletions(-) - ---- a/drivers/spi/spi-cadence-quadspi.c -+++ b/drivers/spi/spi-cadence-quadspi.c -@@ -1249,10 +1249,7 @@ static bool cqspi_supports_mem_op(struct - return false; - } - -- if (all_true) -- return spi_mem_dtr_supports_op(mem, op); -- else -- return spi_mem_default_supports_op(mem, op); -+ return spi_mem_default_supports_op(mem, op); - } - - static int cqspi_of_get_flash_pdata(struct platform_device *pdev, ---- a/drivers/spi/spi-mem.c -+++ b/drivers/spi/spi-mem.c -@@ -160,16 +160,6 @@ static bool spi_mem_check_buswidth(struc - return true; - } - --bool spi_mem_dtr_supports_op(struct spi_mem *mem, -- const struct spi_mem_op *op) --{ -- if (op->cmd.nbytes != 2) -- return false; -- -- return spi_mem_check_buswidth(mem, op); --} --EXPORT_SYMBOL_GPL(spi_mem_dtr_supports_op); -- - bool spi_mem_default_supports_op(struct spi_mem *mem, - const struct spi_mem_op *op) - { ---- a/drivers/spi/spi-mxic.c -+++ b/drivers/spi/spi-mxic.c -@@ -331,8 +331,6 @@ static int mxic_spi_data_xfer(struct mxi - static bool mxic_spi_mem_supports_op(struct spi_mem *mem, - const struct spi_mem_op *op) - { -- bool all_false; -- - if (op->data.buswidth > 8 || op->addr.buswidth > 8 || - op->dummy.buswidth > 8 || op->cmd.buswidth > 8) - return false; -@@ -344,13 +342,7 @@ static bool mxic_spi_mem_supports_op(str - if (op->addr.nbytes > 7) - return false; - -- all_false = !op->cmd.dtr && !op->addr.dtr && !op->dummy.dtr && -- !op->data.dtr; -- -- if (all_false) -- return spi_mem_default_supports_op(mem, op); -- else -- return spi_mem_dtr_supports_op(mem, op); -+ return spi_mem_default_supports_op(mem, op); - } - - static int mxic_spi_mem_exec_op(struct spi_mem *mem, ---- a/include/linux/spi/spi-mem.h -+++ b/include/linux/spi/spi-mem.h -@@ -330,10 +330,6 @@ void spi_controller_dma_unmap_mem_op_dat - - bool spi_mem_default_supports_op(struct spi_mem *mem, - const struct spi_mem_op *op); -- --bool spi_mem_dtr_supports_op(struct spi_mem *mem, -- const struct spi_mem_op *op); -- - #else - static inline int - spi_controller_dma_map_mem_op_data(struct spi_controller *ctlr, -@@ -356,13 +352,6 @@ bool spi_mem_default_supports_op(struct - { - return false; - } -- --static inline --bool spi_mem_dtr_supports_op(struct spi_mem *mem, -- const struct spi_mem_op *op) --{ -- return false; --} - #endif /* CONFIG_SPI_MEM */ - - int spi_mem_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op); diff --git a/target/linux/mediatek/patches-5.15/120-07-v5.18-spi-spi-mem-Add-an-ecc-parameter-to-the-spi_mem_op-s.patch b/target/linux/mediatek/patches-5.15/120-07-v5.18-spi-spi-mem-Add-an-ecc-parameter-to-the-spi_mem_op-s.patch deleted file mode 100644 index 6d7e47650b..0000000000 --- a/target/linux/mediatek/patches-5.15/120-07-v5.18-spi-spi-mem-Add-an-ecc-parameter-to-the-spi_mem_op-s.patch +++ /dev/null @@ -1,72 +0,0 @@ -From 9e7eb0ea442ecb1c3fe443289e288694f10c5148 Mon Sep 17 00:00:00 2001 -From: Miquel Raynal -Date: Thu, 27 Jan 2022 10:18:01 +0100 -Subject: [PATCH 07/15] spi: spi-mem: Add an ecc parameter to the spi_mem_op - structure - -Soon the SPI-NAND core will need a way to request a SPI controller to -enable ECC support for a given operation. This is because of the -pipelined integration of certain ECC engines, which are directly managed -by the SPI controller itself. - -Introduce a spi_mem_op additional field for this purpose: ecc. - -So far this field is left unset and checked to be false by all -the SPI controller drivers in their ->supports_op() hook, as they all -call spi_mem_default_supports_op(). - -Signed-off-by: Miquel Raynal -Acked-by: Pratyush Yadav -Reviewed-by: Boris Brezillon -Reviewed-by: Tudor Ambarus -Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-7-miquel.raynal@bootlin.com -(cherry picked from commit a433c2cbd75ab76f277364f44e76f32c7df306e7) ---- - drivers/spi/spi-mem.c | 5 +++++ - include/linux/spi/spi-mem.h | 4 ++++ - 2 files changed, 9 insertions(+) - ---- a/drivers/spi/spi-mem.c -+++ b/drivers/spi/spi-mem.c -@@ -178,6 +178,11 @@ bool spi_mem_default_supports_op(struct - return false; - } - -+ if (op->data.ecc) { -+ if (!spi_mem_controller_is_capable(ctlr, ecc)) -+ return false; -+ } -+ - return spi_mem_check_buswidth(mem, op); - } - EXPORT_SYMBOL_GPL(spi_mem_default_supports_op); ---- a/include/linux/spi/spi-mem.h -+++ b/include/linux/spi/spi-mem.h -@@ -89,6 +89,7 @@ enum spi_mem_data_dir { - * @dummy.dtr: whether the dummy bytes should be sent in DTR mode or not - * @data.buswidth: number of IO lanes used to send/receive the data - * @data.dtr: whether the data should be sent in DTR mode or not -+ * @data.ecc: whether error correction is required or not - * @data.dir: direction of the transfer - * @data.nbytes: number of data bytes to send/receive. Can be zero if the - * operation does not involve transferring data -@@ -119,6 +120,7 @@ struct spi_mem_op { - struct { - u8 buswidth; - u8 dtr : 1; -+ u8 ecc : 1; - enum spi_mem_data_dir dir; - unsigned int nbytes; - union { -@@ -288,9 +290,11 @@ struct spi_controller_mem_ops { - /** - * struct spi_controller_mem_caps - SPI memory controller capabilities - * @dtr: Supports DTR operations -+ * @ecc: Supports operations with error correction - */ - struct spi_controller_mem_caps { - bool dtr; -+ bool ecc; - }; - - #define spi_mem_controller_is_capable(ctlr, cap) \ diff --git a/target/linux/mediatek/patches-5.15/120-08-v5.18-mtd-spinand-Delay-a-little-bit-the-dirmap-creation.patch b/target/linux/mediatek/patches-5.15/120-08-v5.18-mtd-spinand-Delay-a-little-bit-the-dirmap-creation.patch deleted file mode 100644 index 87c7b7cd29..0000000000 --- a/target/linux/mediatek/patches-5.15/120-08-v5.18-mtd-spinand-Delay-a-little-bit-the-dirmap-creation.patch +++ /dev/null @@ -1,50 +0,0 @@ -From 94ef3c35b935a63f6c156957c92f6cf33c9a8dae Mon Sep 17 00:00:00 2001 -From: Miquel Raynal -Date: Thu, 27 Jan 2022 10:18:02 +0100 -Subject: [PATCH 08/15] mtd: spinand: Delay a little bit the dirmap creation - -As we will soon tweak the dirmap creation to act a little bit -differently depending on the picked ECC engine, we need to initialize -dirmaps after ECC engines. This should not have any effect as dirmaps -are not yet used at this point. - -Signed-off-by: Miquel Raynal -Reviewed-by: Boris Brezillon -Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-8-miquel.raynal@bootlin.com -(cherry picked from commit dc4c2cbf0be2d4a8e2a65013ea2815bb2c8ba949) ---- - drivers/mtd/nand/spi/core.c | 16 ++++++++-------- - 1 file changed, 8 insertions(+), 8 deletions(-) - ---- a/drivers/mtd/nand/spi/core.c -+++ b/drivers/mtd/nand/spi/core.c -@@ -1221,14 +1221,6 @@ static int spinand_init(struct spinand_d - if (ret) - goto err_free_bufs; - -- ret = spinand_create_dirmaps(spinand); -- if (ret) { -- dev_err(dev, -- "Failed to create direct mappings for read/write operations (err = %d)\n", -- ret); -- goto err_manuf_cleanup; -- } -- - ret = nanddev_init(nand, &spinand_ops, THIS_MODULE); - if (ret) - goto err_manuf_cleanup; -@@ -1263,6 +1255,14 @@ static int spinand_init(struct spinand_d - mtd->ecc_strength = nanddev_get_ecc_conf(nand)->strength; - mtd->ecc_step_size = nanddev_get_ecc_conf(nand)->step_size; - -+ ret = spinand_create_dirmaps(spinand); -+ if (ret) { -+ dev_err(dev, -+ "Failed to create direct mappings for read/write operations (err = %d)\n", -+ ret); -+ goto err_cleanup_ecc_engine; -+ } -+ - return 0; - - err_cleanup_ecc_engine: diff --git a/target/linux/mediatek/patches-5.15/120-09-v5.18-mtd-spinand-Create-direct-mapping-descriptors-for-EC.patch b/target/linux/mediatek/patches-5.15/120-09-v5.18-mtd-spinand-Create-direct-mapping-descriptors-for-EC.patch deleted file mode 100644 index 35912cd2cd..0000000000 --- a/target/linux/mediatek/patches-5.15/120-09-v5.18-mtd-spinand-Create-direct-mapping-descriptors-for-EC.patch +++ /dev/null @@ -1,98 +0,0 @@ -From eb4a2d282c3c5752211d69be6dff2674119e5583 Mon Sep 17 00:00:00 2001 -From: Miquel Raynal -Date: Thu, 27 Jan 2022 10:18:03 +0100 -Subject: [PATCH 09/15] mtd: spinand: Create direct mapping descriptors for ECC - operations - -In order for pipelined ECC engines to be able to enable/disable the ECC -engine only when needed and avoid races when future parallel-operations -will be supported, we need to provide the information about the use of -the ECC engine in the direct mapping hooks. As direct mapping -configurations are meant to be static, it is best to create two new -mappings: one for regular 'raw' accesses and one for accesses involving -correction. It is up to the driver to use or not the new ECC enable -boolean contained in the spi-mem operation. - -As dirmaps are not free (they consume a few pages of MMIO address space) -and because these extra entries are only meant to be used by pipelined -engines, let's limit their use to this specific type of engine and save -a bit of memory with all the other setups. - -Signed-off-by: Miquel Raynal -Reviewed-by: Boris Brezillon -Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-9-miquel.raynal@bootlin.com -(cherry picked from commit f9d7c7265bcff7d9a17425a8cddf702e8fe159c2) ---- - drivers/mtd/nand/spi/core.c | 35 +++++++++++++++++++++++++++++++++-- - include/linux/mtd/spinand.h | 2 ++ - 2 files changed, 35 insertions(+), 2 deletions(-) - ---- a/drivers/mtd/nand/spi/core.c -+++ b/drivers/mtd/nand/spi/core.c -@@ -381,7 +381,10 @@ static int spinand_read_from_cache_op(st - } - } - -- rdesc = spinand->dirmaps[req->pos.plane].rdesc; -+ if (req->mode == MTD_OPS_RAW) -+ rdesc = spinand->dirmaps[req->pos.plane].rdesc; -+ else -+ rdesc = spinand->dirmaps[req->pos.plane].rdesc_ecc; - - while (nbytes) { - ret = spi_mem_dirmap_read(rdesc, column, nbytes, buf); -@@ -452,7 +455,10 @@ static int spinand_write_to_cache_op(str - req->ooblen); - } - -- wdesc = spinand->dirmaps[req->pos.plane].wdesc; -+ if (req->mode == MTD_OPS_RAW) -+ wdesc = spinand->dirmaps[req->pos.plane].wdesc; -+ else -+ wdesc = spinand->dirmaps[req->pos.plane].wdesc_ecc; - - while (nbytes) { - ret = spi_mem_dirmap_write(wdesc, column, nbytes, buf); -@@ -875,6 +881,31 @@ static int spinand_create_dirmap(struct - - spinand->dirmaps[plane].rdesc = desc; - -+ if (nand->ecc.engine->integration != NAND_ECC_ENGINE_INTEGRATION_PIPELINED) { -+ spinand->dirmaps[plane].wdesc_ecc = spinand->dirmaps[plane].wdesc; -+ spinand->dirmaps[plane].rdesc_ecc = spinand->dirmaps[plane].rdesc; -+ -+ return 0; -+ } -+ -+ info.op_tmpl = *spinand->op_templates.update_cache; -+ info.op_tmpl.data.ecc = true; -+ desc = devm_spi_mem_dirmap_create(&spinand->spimem->spi->dev, -+ spinand->spimem, &info); -+ if (IS_ERR(desc)) -+ return PTR_ERR(desc); -+ -+ spinand->dirmaps[plane].wdesc_ecc = desc; -+ -+ info.op_tmpl = *spinand->op_templates.read_cache; -+ info.op_tmpl.data.ecc = true; -+ desc = devm_spi_mem_dirmap_create(&spinand->spimem->spi->dev, -+ spinand->spimem, &info); -+ if (IS_ERR(desc)) -+ return PTR_ERR(desc); -+ -+ spinand->dirmaps[plane].rdesc_ecc = desc; -+ - return 0; - } - ---- a/include/linux/mtd/spinand.h -+++ b/include/linux/mtd/spinand.h -@@ -392,6 +392,8 @@ struct spinand_info { - struct spinand_dirmap { - struct spi_mem_dirmap_desc *wdesc; - struct spi_mem_dirmap_desc *rdesc; -+ struct spi_mem_dirmap_desc *wdesc_ecc; -+ struct spi_mem_dirmap_desc *rdesc_ecc; - }; - - /** diff --git a/target/linux/mediatek/patches-5.15/120-11-v5.19-mtd-nand-make-mtk_ecc.c-a-separated-module.patch b/target/linux/mediatek/patches-5.15/120-11-v5.19-mtd-nand-make-mtk_ecc.c-a-separated-module.patch deleted file mode 100644 index fd9098eae9..0000000000 --- a/target/linux/mediatek/patches-5.15/120-11-v5.19-mtd-nand-make-mtk_ecc.c-a-separated-module.patch +++ /dev/null @@ -1,1383 +0,0 @@ -From ebb9653d4a87c64fb679e4c339e867556dada719 Mon Sep 17 00:00:00 2001 -From: Chuanhong Guo -Date: Tue, 22 Mar 2022 18:44:21 +0800 -Subject: [PATCH 11/15] mtd: nand: make mtk_ecc.c a separated module - -this code will be used in mediatek snfi spi-mem controller with -pipelined ECC engine. - -Signed-off-by: Chuanhong Guo -(cherry picked from commit 316f47cec4ce5b81aa8006de202d8769c117a52d) ---- - drivers/mtd/nand/Kconfig | 7 +++++++ - drivers/mtd/nand/Makefile | 1 + - drivers/mtd/nand/{raw/mtk_ecc.c => ecc-mtk.c} | 3 +-- - drivers/mtd/nand/raw/Kconfig | 1 + - drivers/mtd/nand/raw/Makefile | 2 +- - drivers/mtd/nand/raw/mtk_nand.c | 2 +- - .../nand/raw/mtk_ecc.h => include/linux/mtd/nand-ecc-mtk.h | 0 - 7 files changed, 12 insertions(+), 4 deletions(-) - rename drivers/mtd/nand/{raw/mtk_ecc.c => ecc-mtk.c} (99%) - rename drivers/mtd/nand/raw/mtk_ecc.h => include/linux/mtd/nand-ecc-mtk.h (100%) - ---- a/drivers/mtd/nand/Kconfig -+++ b/drivers/mtd/nand/Kconfig -@@ -50,6 +50,13 @@ config MTD_NAND_MTK_BMT - bool "Support MediaTek NAND Bad-block Management Table" - default n - -+config MTD_NAND_ECC_MEDIATEK -+ tristate "Mediatek hardware ECC engine" -+ depends on HAS_IOMEM -+ select MTD_NAND_ECC -+ help -+ This enables support for the hardware ECC engine from Mediatek. -+ - endmenu - - endmenu ---- a/drivers/mtd/nand/Makefile -+++ b/drivers/mtd/nand/Makefile -@@ -3,6 +3,7 @@ - nandcore-objs := core.o bbt.o - obj-$(CONFIG_MTD_NAND_CORE) += nandcore.o - obj-$(CONFIG_MTD_NAND_MTK_BMT) += mtk_bmt.o mtk_bmt_v2.o mtk_bmt_bbt.o mtk_bmt_nmbm.o -+obj-$(CONFIG_MTD_NAND_ECC_MEDIATEK) += ecc-mtk.o - - obj-y += onenand/ - obj-y += raw/ ---- a/drivers/mtd/nand/raw/mtk_ecc.c -+++ /dev/null -@@ -1,599 +0,0 @@ --// SPDX-License-Identifier: GPL-2.0 OR MIT --/* -- * MTK ECC controller driver. -- * Copyright (C) 2016 MediaTek Inc. -- * Authors: Xiaolei Li -- * Jorge Ramirez-Ortiz -- */ -- --#include --#include --#include --#include --#include --#include --#include --#include --#include -- --#include "mtk_ecc.h" -- --#define ECC_IDLE_MASK BIT(0) --#define ECC_IRQ_EN BIT(0) --#define ECC_PG_IRQ_SEL BIT(1) --#define ECC_OP_ENABLE (1) --#define ECC_OP_DISABLE (0) -- --#define ECC_ENCCON (0x00) --#define ECC_ENCCNFG (0x04) --#define ECC_MS_SHIFT (16) --#define ECC_ENCDIADDR (0x08) --#define ECC_ENCIDLE (0x0C) --#define ECC_DECCON (0x100) --#define ECC_DECCNFG (0x104) --#define DEC_EMPTY_EN BIT(31) --#define DEC_CNFG_CORRECT (0x3 << 12) --#define ECC_DECIDLE (0x10C) --#define ECC_DECENUM0 (0x114) -- --#define ECC_TIMEOUT (500000) -- --#define ECC_IDLE_REG(op) ((op) == ECC_ENCODE ? ECC_ENCIDLE : ECC_DECIDLE) --#define ECC_CTL_REG(op) ((op) == ECC_ENCODE ? ECC_ENCCON : ECC_DECCON) -- --struct mtk_ecc_caps { -- u32 err_mask; -- u32 err_shift; -- const u8 *ecc_strength; -- const u32 *ecc_regs; -- u8 num_ecc_strength; -- u8 ecc_mode_shift; -- u32 parity_bits; -- int pg_irq_sel; --}; -- --struct mtk_ecc { -- struct device *dev; -- const struct mtk_ecc_caps *caps; -- void __iomem *regs; -- struct clk *clk; -- -- struct completion done; -- struct mutex lock; -- u32 sectors; -- -- u8 *eccdata; --}; -- --/* ecc strength that each IP supports */ --static const u8 ecc_strength_mt2701[] = { -- 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, -- 40, 44, 48, 52, 56, 60 --}; -- --static const u8 ecc_strength_mt2712[] = { -- 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, -- 40, 44, 48, 52, 56, 60, 68, 72, 80 --}; -- --static const u8 ecc_strength_mt7622[] = { -- 4, 6, 8, 10, 12 --}; -- --enum mtk_ecc_regs { -- ECC_ENCPAR00, -- ECC_ENCIRQ_EN, -- ECC_ENCIRQ_STA, -- ECC_DECDONE, -- ECC_DECIRQ_EN, -- ECC_DECIRQ_STA, --}; -- --static int mt2701_ecc_regs[] = { -- [ECC_ENCPAR00] = 0x10, -- [ECC_ENCIRQ_EN] = 0x80, -- [ECC_ENCIRQ_STA] = 0x84, -- [ECC_DECDONE] = 0x124, -- [ECC_DECIRQ_EN] = 0x200, -- [ECC_DECIRQ_STA] = 0x204, --}; -- --static int mt2712_ecc_regs[] = { -- [ECC_ENCPAR00] = 0x300, -- [ECC_ENCIRQ_EN] = 0x80, -- [ECC_ENCIRQ_STA] = 0x84, -- [ECC_DECDONE] = 0x124, -- [ECC_DECIRQ_EN] = 0x200, -- [ECC_DECIRQ_STA] = 0x204, --}; -- --static int mt7622_ecc_regs[] = { -- [ECC_ENCPAR00] = 0x10, -- [ECC_ENCIRQ_EN] = 0x30, -- [ECC_ENCIRQ_STA] = 0x34, -- [ECC_DECDONE] = 0x11c, -- [ECC_DECIRQ_EN] = 0x140, -- [ECC_DECIRQ_STA] = 0x144, --}; -- --static inline void mtk_ecc_wait_idle(struct mtk_ecc *ecc, -- enum mtk_ecc_operation op) --{ -- struct device *dev = ecc->dev; -- u32 val; -- int ret; -- -- ret = readl_poll_timeout_atomic(ecc->regs + ECC_IDLE_REG(op), val, -- val & ECC_IDLE_MASK, -- 10, ECC_TIMEOUT); -- if (ret) -- dev_warn(dev, "%s NOT idle\n", -- op == ECC_ENCODE ? "encoder" : "decoder"); --} -- --static irqreturn_t mtk_ecc_irq(int irq, void *id) --{ -- struct mtk_ecc *ecc = id; -- u32 dec, enc; -- -- dec = readw(ecc->regs + ecc->caps->ecc_regs[ECC_DECIRQ_STA]) -- & ECC_IRQ_EN; -- if (dec) { -- dec = readw(ecc->regs + ecc->caps->ecc_regs[ECC_DECDONE]); -- if (dec & ecc->sectors) { -- /* -- * Clear decode IRQ status once again to ensure that -- * there will be no extra IRQ. -- */ -- readw(ecc->regs + ecc->caps->ecc_regs[ECC_DECIRQ_STA]); -- ecc->sectors = 0; -- complete(&ecc->done); -- } else { -- return IRQ_HANDLED; -- } -- } else { -- enc = readl(ecc->regs + ecc->caps->ecc_regs[ECC_ENCIRQ_STA]) -- & ECC_IRQ_EN; -- if (enc) -- complete(&ecc->done); -- else -- return IRQ_NONE; -- } -- -- return IRQ_HANDLED; --} -- --static int mtk_ecc_config(struct mtk_ecc *ecc, struct mtk_ecc_config *config) --{ -- u32 ecc_bit, dec_sz, enc_sz; -- u32 reg, i; -- -- for (i = 0; i < ecc->caps->num_ecc_strength; i++) { -- if (ecc->caps->ecc_strength[i] == config->strength) -- break; -- } -- -- if (i == ecc->caps->num_ecc_strength) { -- dev_err(ecc->dev, "invalid ecc strength %d\n", -- config->strength); -- return -EINVAL; -- } -- -- ecc_bit = i; -- -- if (config->op == ECC_ENCODE) { -- /* configure ECC encoder (in bits) */ -- enc_sz = config->len << 3; -- -- reg = ecc_bit | (config->mode << ecc->caps->ecc_mode_shift); -- reg |= (enc_sz << ECC_MS_SHIFT); -- writel(reg, ecc->regs + ECC_ENCCNFG); -- -- if (config->mode != ECC_NFI_MODE) -- writel(lower_32_bits(config->addr), -- ecc->regs + ECC_ENCDIADDR); -- -- } else { -- /* configure ECC decoder (in bits) */ -- dec_sz = (config->len << 3) + -- config->strength * ecc->caps->parity_bits; -- -- reg = ecc_bit | (config->mode << ecc->caps->ecc_mode_shift); -- reg |= (dec_sz << ECC_MS_SHIFT) | DEC_CNFG_CORRECT; -- reg |= DEC_EMPTY_EN; -- writel(reg, ecc->regs + ECC_DECCNFG); -- -- if (config->sectors) -- ecc->sectors = 1 << (config->sectors - 1); -- } -- -- return 0; --} -- --void mtk_ecc_get_stats(struct mtk_ecc *ecc, struct mtk_ecc_stats *stats, -- int sectors) --{ -- u32 offset, i, err; -- u32 bitflips = 0; -- -- stats->corrected = 0; -- stats->failed = 0; -- -- for (i = 0; i < sectors; i++) { -- offset = (i >> 2) << 2; -- err = readl(ecc->regs + ECC_DECENUM0 + offset); -- err = err >> ((i % 4) * ecc->caps->err_shift); -- err &= ecc->caps->err_mask; -- if (err == ecc->caps->err_mask) { -- /* uncorrectable errors */ -- stats->failed++; -- continue; -- } -- -- stats->corrected += err; -- bitflips = max_t(u32, bitflips, err); -- } -- -- stats->bitflips = bitflips; --} --EXPORT_SYMBOL(mtk_ecc_get_stats); -- --void mtk_ecc_release(struct mtk_ecc *ecc) --{ -- clk_disable_unprepare(ecc->clk); -- put_device(ecc->dev); --} --EXPORT_SYMBOL(mtk_ecc_release); -- --static void mtk_ecc_hw_init(struct mtk_ecc *ecc) --{ -- mtk_ecc_wait_idle(ecc, ECC_ENCODE); -- writew(ECC_OP_DISABLE, ecc->regs + ECC_ENCCON); -- -- mtk_ecc_wait_idle(ecc, ECC_DECODE); -- writel(ECC_OP_DISABLE, ecc->regs + ECC_DECCON); --} -- --static struct mtk_ecc *mtk_ecc_get(struct device_node *np) --{ -- struct platform_device *pdev; -- struct mtk_ecc *ecc; -- -- pdev = of_find_device_by_node(np); -- if (!pdev) -- return ERR_PTR(-EPROBE_DEFER); -- -- ecc = platform_get_drvdata(pdev); -- if (!ecc) { -- put_device(&pdev->dev); -- return ERR_PTR(-EPROBE_DEFER); -- } -- -- clk_prepare_enable(ecc->clk); -- mtk_ecc_hw_init(ecc); -- -- return ecc; --} -- --struct mtk_ecc *of_mtk_ecc_get(struct device_node *of_node) --{ -- struct mtk_ecc *ecc = NULL; -- struct device_node *np; -- -- np = of_parse_phandle(of_node, "ecc-engine", 0); -- if (np) { -- ecc = mtk_ecc_get(np); -- of_node_put(np); -- } -- -- return ecc; --} --EXPORT_SYMBOL(of_mtk_ecc_get); -- --int mtk_ecc_enable(struct mtk_ecc *ecc, struct mtk_ecc_config *config) --{ -- enum mtk_ecc_operation op = config->op; -- u16 reg_val; -- int ret; -- -- ret = mutex_lock_interruptible(&ecc->lock); -- if (ret) { -- dev_err(ecc->dev, "interrupted when attempting to lock\n"); -- return ret; -- } -- -- mtk_ecc_wait_idle(ecc, op); -- -- ret = mtk_ecc_config(ecc, config); -- if (ret) { -- mutex_unlock(&ecc->lock); -- return ret; -- } -- -- if (config->mode != ECC_NFI_MODE || op != ECC_ENCODE) { -- init_completion(&ecc->done); -- reg_val = ECC_IRQ_EN; -- /* -- * For ECC_NFI_MODE, if ecc->caps->pg_irq_sel is 1, then it -- * means this chip can only generate one ecc irq during page -- * read / write. If is 0, generate one ecc irq each ecc step. -- */ -- if (ecc->caps->pg_irq_sel && config->mode == ECC_NFI_MODE) -- reg_val |= ECC_PG_IRQ_SEL; -- if (op == ECC_ENCODE) -- writew(reg_val, ecc->regs + -- ecc->caps->ecc_regs[ECC_ENCIRQ_EN]); -- else -- writew(reg_val, ecc->regs + -- ecc->caps->ecc_regs[ECC_DECIRQ_EN]); -- } -- -- writew(ECC_OP_ENABLE, ecc->regs + ECC_CTL_REG(op)); -- -- return 0; --} --EXPORT_SYMBOL(mtk_ecc_enable); -- --void mtk_ecc_disable(struct mtk_ecc *ecc) --{ -- enum mtk_ecc_operation op = ECC_ENCODE; -- -- /* find out the running operation */ -- if (readw(ecc->regs + ECC_CTL_REG(op)) != ECC_OP_ENABLE) -- op = ECC_DECODE; -- -- /* disable it */ -- mtk_ecc_wait_idle(ecc, op); -- if (op == ECC_DECODE) { -- /* -- * Clear decode IRQ status in case there is a timeout to wait -- * decode IRQ. -- */ -- readw(ecc->regs + ecc->caps->ecc_regs[ECC_DECDONE]); -- writew(0, ecc->regs + ecc->caps->ecc_regs[ECC_DECIRQ_EN]); -- } else { -- writew(0, ecc->regs + ecc->caps->ecc_regs[ECC_ENCIRQ_EN]); -- } -- -- writew(ECC_OP_DISABLE, ecc->regs + ECC_CTL_REG(op)); -- -- mutex_unlock(&ecc->lock); --} --EXPORT_SYMBOL(mtk_ecc_disable); -- --int mtk_ecc_wait_done(struct mtk_ecc *ecc, enum mtk_ecc_operation op) --{ -- int ret; -- -- ret = wait_for_completion_timeout(&ecc->done, msecs_to_jiffies(500)); -- if (!ret) { -- dev_err(ecc->dev, "%s timeout - interrupt did not arrive)\n", -- (op == ECC_ENCODE) ? "encoder" : "decoder"); -- return -ETIMEDOUT; -- } -- -- return 0; --} --EXPORT_SYMBOL(mtk_ecc_wait_done); -- --int mtk_ecc_encode(struct mtk_ecc *ecc, struct mtk_ecc_config *config, -- u8 *data, u32 bytes) --{ -- dma_addr_t addr; -- u32 len; -- int ret; -- -- addr = dma_map_single(ecc->dev, data, bytes, DMA_TO_DEVICE); -- ret = dma_mapping_error(ecc->dev, addr); -- if (ret) { -- dev_err(ecc->dev, "dma mapping error\n"); -- return -EINVAL; -- } -- -- config->op = ECC_ENCODE; -- config->addr = addr; -- ret = mtk_ecc_enable(ecc, config); -- if (ret) { -- dma_unmap_single(ecc->dev, addr, bytes, DMA_TO_DEVICE); -- return ret; -- } -- -- ret = mtk_ecc_wait_done(ecc, ECC_ENCODE); -- if (ret) -- goto timeout; -- -- mtk_ecc_wait_idle(ecc, ECC_ENCODE); -- -- /* Program ECC bytes to OOB: per sector oob = FDM + ECC + SPARE */ -- len = (config->strength * ecc->caps->parity_bits + 7) >> 3; -- -- /* write the parity bytes generated by the ECC back to temp buffer */ -- __ioread32_copy(ecc->eccdata, -- ecc->regs + ecc->caps->ecc_regs[ECC_ENCPAR00], -- round_up(len, 4)); -- -- /* copy into possibly unaligned OOB region with actual length */ -- memcpy(data + bytes, ecc->eccdata, len); --timeout: -- -- dma_unmap_single(ecc->dev, addr, bytes, DMA_TO_DEVICE); -- mtk_ecc_disable(ecc); -- -- return ret; --} --EXPORT_SYMBOL(mtk_ecc_encode); -- --void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p) --{ -- const u8 *ecc_strength = ecc->caps->ecc_strength; -- int i; -- -- for (i = 0; i < ecc->caps->num_ecc_strength; i++) { -- if (*p <= ecc_strength[i]) { -- if (!i) -- *p = ecc_strength[i]; -- else if (*p != ecc_strength[i]) -- *p = ecc_strength[i - 1]; -- return; -- } -- } -- -- *p = ecc_strength[ecc->caps->num_ecc_strength - 1]; --} --EXPORT_SYMBOL(mtk_ecc_adjust_strength); -- --unsigned int mtk_ecc_get_parity_bits(struct mtk_ecc *ecc) --{ -- return ecc->caps->parity_bits; --} --EXPORT_SYMBOL(mtk_ecc_get_parity_bits); -- --static const struct mtk_ecc_caps mtk_ecc_caps_mt2701 = { -- .err_mask = 0x3f, -- .err_shift = 8, -- .ecc_strength = ecc_strength_mt2701, -- .ecc_regs = mt2701_ecc_regs, -- .num_ecc_strength = 20, -- .ecc_mode_shift = 5, -- .parity_bits = 14, -- .pg_irq_sel = 0, --}; -- --static const struct mtk_ecc_caps mtk_ecc_caps_mt2712 = { -- .err_mask = 0x7f, -- .err_shift = 8, -- .ecc_strength = ecc_strength_mt2712, -- .ecc_regs = mt2712_ecc_regs, -- .num_ecc_strength = 23, -- .ecc_mode_shift = 5, -- .parity_bits = 14, -- .pg_irq_sel = 1, --}; -- --static const struct mtk_ecc_caps mtk_ecc_caps_mt7622 = { -- .err_mask = 0x1f, -- .err_shift = 5, -- .ecc_strength = ecc_strength_mt7622, -- .ecc_regs = mt7622_ecc_regs, -- .num_ecc_strength = 5, -- .ecc_mode_shift = 4, -- .parity_bits = 13, -- .pg_irq_sel = 0, --}; -- --static const struct of_device_id mtk_ecc_dt_match[] = { -- { -- .compatible = "mediatek,mt2701-ecc", -- .data = &mtk_ecc_caps_mt2701, -- }, { -- .compatible = "mediatek,mt2712-ecc", -- .data = &mtk_ecc_caps_mt2712, -- }, { -- .compatible = "mediatek,mt7622-ecc", -- .data = &mtk_ecc_caps_mt7622, -- }, -- {}, --}; -- --static int mtk_ecc_probe(struct platform_device *pdev) --{ -- struct device *dev = &pdev->dev; -- struct mtk_ecc *ecc; -- struct resource *res; -- u32 max_eccdata_size; -- int irq, ret; -- -- ecc = devm_kzalloc(dev, sizeof(*ecc), GFP_KERNEL); -- if (!ecc) -- return -ENOMEM; -- -- ecc->caps = of_device_get_match_data(dev); -- -- max_eccdata_size = ecc->caps->num_ecc_strength - 1; -- max_eccdata_size = ecc->caps->ecc_strength[max_eccdata_size]; -- max_eccdata_size = (max_eccdata_size * ecc->caps->parity_bits + 7) >> 3; -- max_eccdata_size = round_up(max_eccdata_size, 4); -- ecc->eccdata = devm_kzalloc(dev, max_eccdata_size, GFP_KERNEL); -- if (!ecc->eccdata) -- return -ENOMEM; -- -- res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -- ecc->regs = devm_ioremap_resource(dev, res); -- if (IS_ERR(ecc->regs)) -- return PTR_ERR(ecc->regs); -- -- ecc->clk = devm_clk_get(dev, NULL); -- if (IS_ERR(ecc->clk)) { -- dev_err(dev, "failed to get clock: %ld\n", PTR_ERR(ecc->clk)); -- return PTR_ERR(ecc->clk); -- } -- -- irq = platform_get_irq(pdev, 0); -- if (irq < 0) -- return irq; -- -- ret = dma_set_mask(dev, DMA_BIT_MASK(32)); -- if (ret) { -- dev_err(dev, "failed to set DMA mask\n"); -- return ret; -- } -- -- ret = devm_request_irq(dev, irq, mtk_ecc_irq, 0x0, "mtk-ecc", ecc); -- if (ret) { -- dev_err(dev, "failed to request irq\n"); -- return -EINVAL; -- } -- -- ecc->dev = dev; -- mutex_init(&ecc->lock); -- platform_set_drvdata(pdev, ecc); -- dev_info(dev, "probed\n"); -- -- return 0; --} -- --#ifdef CONFIG_PM_SLEEP --static int mtk_ecc_suspend(struct device *dev) --{ -- struct mtk_ecc *ecc = dev_get_drvdata(dev); -- -- clk_disable_unprepare(ecc->clk); -- -- return 0; --} -- --static int mtk_ecc_resume(struct device *dev) --{ -- struct mtk_ecc *ecc = dev_get_drvdata(dev); -- int ret; -- -- ret = clk_prepare_enable(ecc->clk); -- if (ret) { -- dev_err(dev, "failed to enable clk\n"); -- return ret; -- } -- -- return 0; --} -- --static SIMPLE_DEV_PM_OPS(mtk_ecc_pm_ops, mtk_ecc_suspend, mtk_ecc_resume); --#endif -- --MODULE_DEVICE_TABLE(of, mtk_ecc_dt_match); -- --static struct platform_driver mtk_ecc_driver = { -- .probe = mtk_ecc_probe, -- .driver = { -- .name = "mtk-ecc", -- .of_match_table = of_match_ptr(mtk_ecc_dt_match), --#ifdef CONFIG_PM_SLEEP -- .pm = &mtk_ecc_pm_ops, --#endif -- }, --}; -- --module_platform_driver(mtk_ecc_driver); -- --MODULE_AUTHOR("Xiaolei Li "); --MODULE_DESCRIPTION("MTK Nand ECC Driver"); --MODULE_LICENSE("Dual MIT/GPL"); ---- /dev/null -+++ b/drivers/mtd/nand/ecc-mtk.c -@@ -0,0 +1,598 @@ -+// SPDX-License-Identifier: GPL-2.0 OR MIT -+/* -+ * MTK ECC controller driver. -+ * Copyright (C) 2016 MediaTek Inc. -+ * Authors: Xiaolei Li -+ * Jorge Ramirez-Ortiz -+ */ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#define ECC_IDLE_MASK BIT(0) -+#define ECC_IRQ_EN BIT(0) -+#define ECC_PG_IRQ_SEL BIT(1) -+#define ECC_OP_ENABLE (1) -+#define ECC_OP_DISABLE (0) -+ -+#define ECC_ENCCON (0x00) -+#define ECC_ENCCNFG (0x04) -+#define ECC_MS_SHIFT (16) -+#define ECC_ENCDIADDR (0x08) -+#define ECC_ENCIDLE (0x0C) -+#define ECC_DECCON (0x100) -+#define ECC_DECCNFG (0x104) -+#define DEC_EMPTY_EN BIT(31) -+#define DEC_CNFG_CORRECT (0x3 << 12) -+#define ECC_DECIDLE (0x10C) -+#define ECC_DECENUM0 (0x114) -+ -+#define ECC_TIMEOUT (500000) -+ -+#define ECC_IDLE_REG(op) ((op) == ECC_ENCODE ? ECC_ENCIDLE : ECC_DECIDLE) -+#define ECC_CTL_REG(op) ((op) == ECC_ENCODE ? ECC_ENCCON : ECC_DECCON) -+ -+struct mtk_ecc_caps { -+ u32 err_mask; -+ u32 err_shift; -+ const u8 *ecc_strength; -+ const u32 *ecc_regs; -+ u8 num_ecc_strength; -+ u8 ecc_mode_shift; -+ u32 parity_bits; -+ int pg_irq_sel; -+}; -+ -+struct mtk_ecc { -+ struct device *dev; -+ const struct mtk_ecc_caps *caps; -+ void __iomem *regs; -+ struct clk *clk; -+ -+ struct completion done; -+ struct mutex lock; -+ u32 sectors; -+ -+ u8 *eccdata; -+}; -+ -+/* ecc strength that each IP supports */ -+static const u8 ecc_strength_mt2701[] = { -+ 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, -+ 40, 44, 48, 52, 56, 60 -+}; -+ -+static const u8 ecc_strength_mt2712[] = { -+ 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36, -+ 40, 44, 48, 52, 56, 60, 68, 72, 80 -+}; -+ -+static const u8 ecc_strength_mt7622[] = { -+ 4, 6, 8, 10, 12 -+}; -+ -+enum mtk_ecc_regs { -+ ECC_ENCPAR00, -+ ECC_ENCIRQ_EN, -+ ECC_ENCIRQ_STA, -+ ECC_DECDONE, -+ ECC_DECIRQ_EN, -+ ECC_DECIRQ_STA, -+}; -+ -+static int mt2701_ecc_regs[] = { -+ [ECC_ENCPAR00] = 0x10, -+ [ECC_ENCIRQ_EN] = 0x80, -+ [ECC_ENCIRQ_STA] = 0x84, -+ [ECC_DECDONE] = 0x124, -+ [ECC_DECIRQ_EN] = 0x200, -+ [ECC_DECIRQ_STA] = 0x204, -+}; -+ -+static int mt2712_ecc_regs[] = { -+ [ECC_ENCPAR00] = 0x300, -+ [ECC_ENCIRQ_EN] = 0x80, -+ [ECC_ENCIRQ_STA] = 0x84, -+ [ECC_DECDONE] = 0x124, -+ [ECC_DECIRQ_EN] = 0x200, -+ [ECC_DECIRQ_STA] = 0x204, -+}; -+ -+static int mt7622_ecc_regs[] = { -+ [ECC_ENCPAR00] = 0x10, -+ [ECC_ENCIRQ_EN] = 0x30, -+ [ECC_ENCIRQ_STA] = 0x34, -+ [ECC_DECDONE] = 0x11c, -+ [ECC_DECIRQ_EN] = 0x140, -+ [ECC_DECIRQ_STA] = 0x144, -+}; -+ -+static inline void mtk_ecc_wait_idle(struct mtk_ecc *ecc, -+ enum mtk_ecc_operation op) -+{ -+ struct device *dev = ecc->dev; -+ u32 val; -+ int ret; -+ -+ ret = readl_poll_timeout_atomic(ecc->regs + ECC_IDLE_REG(op), val, -+ val & ECC_IDLE_MASK, -+ 10, ECC_TIMEOUT); -+ if (ret) -+ dev_warn(dev, "%s NOT idle\n", -+ op == ECC_ENCODE ? "encoder" : "decoder"); -+} -+ -+static irqreturn_t mtk_ecc_irq(int irq, void *id) -+{ -+ struct mtk_ecc *ecc = id; -+ u32 dec, enc; -+ -+ dec = readw(ecc->regs + ecc->caps->ecc_regs[ECC_DECIRQ_STA]) -+ & ECC_IRQ_EN; -+ if (dec) { -+ dec = readw(ecc->regs + ecc->caps->ecc_regs[ECC_DECDONE]); -+ if (dec & ecc->sectors) { -+ /* -+ * Clear decode IRQ status once again to ensure that -+ * there will be no extra IRQ. -+ */ -+ readw(ecc->regs + ecc->caps->ecc_regs[ECC_DECIRQ_STA]); -+ ecc->sectors = 0; -+ complete(&ecc->done); -+ } else { -+ return IRQ_HANDLED; -+ } -+ } else { -+ enc = readl(ecc->regs + ecc->caps->ecc_regs[ECC_ENCIRQ_STA]) -+ & ECC_IRQ_EN; -+ if (enc) -+ complete(&ecc->done); -+ else -+ return IRQ_NONE; -+ } -+ -+ return IRQ_HANDLED; -+} -+ -+static int mtk_ecc_config(struct mtk_ecc *ecc, struct mtk_ecc_config *config) -+{ -+ u32 ecc_bit, dec_sz, enc_sz; -+ u32 reg, i; -+ -+ for (i = 0; i < ecc->caps->num_ecc_strength; i++) { -+ if (ecc->caps->ecc_strength[i] == config->strength) -+ break; -+ } -+ -+ if (i == ecc->caps->num_ecc_strength) { -+ dev_err(ecc->dev, "invalid ecc strength %d\n", -+ config->strength); -+ return -EINVAL; -+ } -+ -+ ecc_bit = i; -+ -+ if (config->op == ECC_ENCODE) { -+ /* configure ECC encoder (in bits) */ -+ enc_sz = config->len << 3; -+ -+ reg = ecc_bit | (config->mode << ecc->caps->ecc_mode_shift); -+ reg |= (enc_sz << ECC_MS_SHIFT); -+ writel(reg, ecc->regs + ECC_ENCCNFG); -+ -+ if (config->mode != ECC_NFI_MODE) -+ writel(lower_32_bits(config->addr), -+ ecc->regs + ECC_ENCDIADDR); -+ -+ } else { -+ /* configure ECC decoder (in bits) */ -+ dec_sz = (config->len << 3) + -+ config->strength * ecc->caps->parity_bits; -+ -+ reg = ecc_bit | (config->mode << ecc->caps->ecc_mode_shift); -+ reg |= (dec_sz << ECC_MS_SHIFT) | DEC_CNFG_CORRECT; -+ reg |= DEC_EMPTY_EN; -+ writel(reg, ecc->regs + ECC_DECCNFG); -+ -+ if (config->sectors) -+ ecc->sectors = 1 << (config->sectors - 1); -+ } -+ -+ return 0; -+} -+ -+void mtk_ecc_get_stats(struct mtk_ecc *ecc, struct mtk_ecc_stats *stats, -+ int sectors) -+{ -+ u32 offset, i, err; -+ u32 bitflips = 0; -+ -+ stats->corrected = 0; -+ stats->failed = 0; -+ -+ for (i = 0; i < sectors; i++) { -+ offset = (i >> 2) << 2; -+ err = readl(ecc->regs + ECC_DECENUM0 + offset); -+ err = err >> ((i % 4) * ecc->caps->err_shift); -+ err &= ecc->caps->err_mask; -+ if (err == ecc->caps->err_mask) { -+ /* uncorrectable errors */ -+ stats->failed++; -+ continue; -+ } -+ -+ stats->corrected += err; -+ bitflips = max_t(u32, bitflips, err); -+ } -+ -+ stats->bitflips = bitflips; -+} -+EXPORT_SYMBOL(mtk_ecc_get_stats); -+ -+void mtk_ecc_release(struct mtk_ecc *ecc) -+{ -+ clk_disable_unprepare(ecc->clk); -+ put_device(ecc->dev); -+} -+EXPORT_SYMBOL(mtk_ecc_release); -+ -+static void mtk_ecc_hw_init(struct mtk_ecc *ecc) -+{ -+ mtk_ecc_wait_idle(ecc, ECC_ENCODE); -+ writew(ECC_OP_DISABLE, ecc->regs + ECC_ENCCON); -+ -+ mtk_ecc_wait_idle(ecc, ECC_DECODE); -+ writel(ECC_OP_DISABLE, ecc->regs + ECC_DECCON); -+} -+ -+static struct mtk_ecc *mtk_ecc_get(struct device_node *np) -+{ -+ struct platform_device *pdev; -+ struct mtk_ecc *ecc; -+ -+ pdev = of_find_device_by_node(np); -+ if (!pdev) -+ return ERR_PTR(-EPROBE_DEFER); -+ -+ ecc = platform_get_drvdata(pdev); -+ if (!ecc) { -+ put_device(&pdev->dev); -+ return ERR_PTR(-EPROBE_DEFER); -+ } -+ -+ clk_prepare_enable(ecc->clk); -+ mtk_ecc_hw_init(ecc); -+ -+ return ecc; -+} -+ -+struct mtk_ecc *of_mtk_ecc_get(struct device_node *of_node) -+{ -+ struct mtk_ecc *ecc = NULL; -+ struct device_node *np; -+ -+ np = of_parse_phandle(of_node, "ecc-engine", 0); -+ if (np) { -+ ecc = mtk_ecc_get(np); -+ of_node_put(np); -+ } -+ -+ return ecc; -+} -+EXPORT_SYMBOL(of_mtk_ecc_get); -+ -+int mtk_ecc_enable(struct mtk_ecc *ecc, struct mtk_ecc_config *config) -+{ -+ enum mtk_ecc_operation op = config->op; -+ u16 reg_val; -+ int ret; -+ -+ ret = mutex_lock_interruptible(&ecc->lock); -+ if (ret) { -+ dev_err(ecc->dev, "interrupted when attempting to lock\n"); -+ return ret; -+ } -+ -+ mtk_ecc_wait_idle(ecc, op); -+ -+ ret = mtk_ecc_config(ecc, config); -+ if (ret) { -+ mutex_unlock(&ecc->lock); -+ return ret; -+ } -+ -+ if (config->mode != ECC_NFI_MODE || op != ECC_ENCODE) { -+ init_completion(&ecc->done); -+ reg_val = ECC_IRQ_EN; -+ /* -+ * For ECC_NFI_MODE, if ecc->caps->pg_irq_sel is 1, then it -+ * means this chip can only generate one ecc irq during page -+ * read / write. If is 0, generate one ecc irq each ecc step. -+ */ -+ if (ecc->caps->pg_irq_sel && config->mode == ECC_NFI_MODE) -+ reg_val |= ECC_PG_IRQ_SEL; -+ if (op == ECC_ENCODE) -+ writew(reg_val, ecc->regs + -+ ecc->caps->ecc_regs[ECC_ENCIRQ_EN]); -+ else -+ writew(reg_val, ecc->regs + -+ ecc->caps->ecc_regs[ECC_DECIRQ_EN]); -+ } -+ -+ writew(ECC_OP_ENABLE, ecc->regs + ECC_CTL_REG(op)); -+ -+ return 0; -+} -+EXPORT_SYMBOL(mtk_ecc_enable); -+ -+void mtk_ecc_disable(struct mtk_ecc *ecc) -+{ -+ enum mtk_ecc_operation op = ECC_ENCODE; -+ -+ /* find out the running operation */ -+ if (readw(ecc->regs + ECC_CTL_REG(op)) != ECC_OP_ENABLE) -+ op = ECC_DECODE; -+ -+ /* disable it */ -+ mtk_ecc_wait_idle(ecc, op); -+ if (op == ECC_DECODE) { -+ /* -+ * Clear decode IRQ status in case there is a timeout to wait -+ * decode IRQ. -+ */ -+ readw(ecc->regs + ecc->caps->ecc_regs[ECC_DECDONE]); -+ writew(0, ecc->regs + ecc->caps->ecc_regs[ECC_DECIRQ_EN]); -+ } else { -+ writew(0, ecc->regs + ecc->caps->ecc_regs[ECC_ENCIRQ_EN]); -+ } -+ -+ writew(ECC_OP_DISABLE, ecc->regs + ECC_CTL_REG(op)); -+ -+ mutex_unlock(&ecc->lock); -+} -+EXPORT_SYMBOL(mtk_ecc_disable); -+ -+int mtk_ecc_wait_done(struct mtk_ecc *ecc, enum mtk_ecc_operation op) -+{ -+ int ret; -+ -+ ret = wait_for_completion_timeout(&ecc->done, msecs_to_jiffies(500)); -+ if (!ret) { -+ dev_err(ecc->dev, "%s timeout - interrupt did not arrive)\n", -+ (op == ECC_ENCODE) ? "encoder" : "decoder"); -+ return -ETIMEDOUT; -+ } -+ -+ return 0; -+} -+EXPORT_SYMBOL(mtk_ecc_wait_done); -+ -+int mtk_ecc_encode(struct mtk_ecc *ecc, struct mtk_ecc_config *config, -+ u8 *data, u32 bytes) -+{ -+ dma_addr_t addr; -+ u32 len; -+ int ret; -+ -+ addr = dma_map_single(ecc->dev, data, bytes, DMA_TO_DEVICE); -+ ret = dma_mapping_error(ecc->dev, addr); -+ if (ret) { -+ dev_err(ecc->dev, "dma mapping error\n"); -+ return -EINVAL; -+ } -+ -+ config->op = ECC_ENCODE; -+ config->addr = addr; -+ ret = mtk_ecc_enable(ecc, config); -+ if (ret) { -+ dma_unmap_single(ecc->dev, addr, bytes, DMA_TO_DEVICE); -+ return ret; -+ } -+ -+ ret = mtk_ecc_wait_done(ecc, ECC_ENCODE); -+ if (ret) -+ goto timeout; -+ -+ mtk_ecc_wait_idle(ecc, ECC_ENCODE); -+ -+ /* Program ECC bytes to OOB: per sector oob = FDM + ECC + SPARE */ -+ len = (config->strength * ecc->caps->parity_bits + 7) >> 3; -+ -+ /* write the parity bytes generated by the ECC back to temp buffer */ -+ __ioread32_copy(ecc->eccdata, -+ ecc->regs + ecc->caps->ecc_regs[ECC_ENCPAR00], -+ round_up(len, 4)); -+ -+ /* copy into possibly unaligned OOB region with actual length */ -+ memcpy(data + bytes, ecc->eccdata, len); -+timeout: -+ -+ dma_unmap_single(ecc->dev, addr, bytes, DMA_TO_DEVICE); -+ mtk_ecc_disable(ecc); -+ -+ return ret; -+} -+EXPORT_SYMBOL(mtk_ecc_encode); -+ -+void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p) -+{ -+ const u8 *ecc_strength = ecc->caps->ecc_strength; -+ int i; -+ -+ for (i = 0; i < ecc->caps->num_ecc_strength; i++) { -+ if (*p <= ecc_strength[i]) { -+ if (!i) -+ *p = ecc_strength[i]; -+ else if (*p != ecc_strength[i]) -+ *p = ecc_strength[i - 1]; -+ return; -+ } -+ } -+ -+ *p = ecc_strength[ecc->caps->num_ecc_strength - 1]; -+} -+EXPORT_SYMBOL(mtk_ecc_adjust_strength); -+ -+unsigned int mtk_ecc_get_parity_bits(struct mtk_ecc *ecc) -+{ -+ return ecc->caps->parity_bits; -+} -+EXPORT_SYMBOL(mtk_ecc_get_parity_bits); -+ -+static const struct mtk_ecc_caps mtk_ecc_caps_mt2701 = { -+ .err_mask = 0x3f, -+ .err_shift = 8, -+ .ecc_strength = ecc_strength_mt2701, -+ .ecc_regs = mt2701_ecc_regs, -+ .num_ecc_strength = 20, -+ .ecc_mode_shift = 5, -+ .parity_bits = 14, -+ .pg_irq_sel = 0, -+}; -+ -+static const struct mtk_ecc_caps mtk_ecc_caps_mt2712 = { -+ .err_mask = 0x7f, -+ .err_shift = 8, -+ .ecc_strength = ecc_strength_mt2712, -+ .ecc_regs = mt2712_ecc_regs, -+ .num_ecc_strength = 23, -+ .ecc_mode_shift = 5, -+ .parity_bits = 14, -+ .pg_irq_sel = 1, -+}; -+ -+static const struct mtk_ecc_caps mtk_ecc_caps_mt7622 = { -+ .err_mask = 0x1f, -+ .err_shift = 5, -+ .ecc_strength = ecc_strength_mt7622, -+ .ecc_regs = mt7622_ecc_regs, -+ .num_ecc_strength = 5, -+ .ecc_mode_shift = 4, -+ .parity_bits = 13, -+ .pg_irq_sel = 0, -+}; -+ -+static const struct of_device_id mtk_ecc_dt_match[] = { -+ { -+ .compatible = "mediatek,mt2701-ecc", -+ .data = &mtk_ecc_caps_mt2701, -+ }, { -+ .compatible = "mediatek,mt2712-ecc", -+ .data = &mtk_ecc_caps_mt2712, -+ }, { -+ .compatible = "mediatek,mt7622-ecc", -+ .data = &mtk_ecc_caps_mt7622, -+ }, -+ {}, -+}; -+ -+static int mtk_ecc_probe(struct platform_device *pdev) -+{ -+ struct device *dev = &pdev->dev; -+ struct mtk_ecc *ecc; -+ struct resource *res; -+ u32 max_eccdata_size; -+ int irq, ret; -+ -+ ecc = devm_kzalloc(dev, sizeof(*ecc), GFP_KERNEL); -+ if (!ecc) -+ return -ENOMEM; -+ -+ ecc->caps = of_device_get_match_data(dev); -+ -+ max_eccdata_size = ecc->caps->num_ecc_strength - 1; -+ max_eccdata_size = ecc->caps->ecc_strength[max_eccdata_size]; -+ max_eccdata_size = (max_eccdata_size * ecc->caps->parity_bits + 7) >> 3; -+ max_eccdata_size = round_up(max_eccdata_size, 4); -+ ecc->eccdata = devm_kzalloc(dev, max_eccdata_size, GFP_KERNEL); -+ if (!ecc->eccdata) -+ return -ENOMEM; -+ -+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -+ ecc->regs = devm_ioremap_resource(dev, res); -+ if (IS_ERR(ecc->regs)) -+ return PTR_ERR(ecc->regs); -+ -+ ecc->clk = devm_clk_get(dev, NULL); -+ if (IS_ERR(ecc->clk)) { -+ dev_err(dev, "failed to get clock: %ld\n", PTR_ERR(ecc->clk)); -+ return PTR_ERR(ecc->clk); -+ } -+ -+ irq = platform_get_irq(pdev, 0); -+ if (irq < 0) -+ return irq; -+ -+ ret = dma_set_mask(dev, DMA_BIT_MASK(32)); -+ if (ret) { -+ dev_err(dev, "failed to set DMA mask\n"); -+ return ret; -+ } -+ -+ ret = devm_request_irq(dev, irq, mtk_ecc_irq, 0x0, "mtk-ecc", ecc); -+ if (ret) { -+ dev_err(dev, "failed to request irq\n"); -+ return -EINVAL; -+ } -+ -+ ecc->dev = dev; -+ mutex_init(&ecc->lock); -+ platform_set_drvdata(pdev, ecc); -+ dev_info(dev, "probed\n"); -+ -+ return 0; -+} -+ -+#ifdef CONFIG_PM_SLEEP -+static int mtk_ecc_suspend(struct device *dev) -+{ -+ struct mtk_ecc *ecc = dev_get_drvdata(dev); -+ -+ clk_disable_unprepare(ecc->clk); -+ -+ return 0; -+} -+ -+static int mtk_ecc_resume(struct device *dev) -+{ -+ struct mtk_ecc *ecc = dev_get_drvdata(dev); -+ int ret; -+ -+ ret = clk_prepare_enable(ecc->clk); -+ if (ret) { -+ dev_err(dev, "failed to enable clk\n"); -+ return ret; -+ } -+ -+ return 0; -+} -+ -+static SIMPLE_DEV_PM_OPS(mtk_ecc_pm_ops, mtk_ecc_suspend, mtk_ecc_resume); -+#endif -+ -+MODULE_DEVICE_TABLE(of, mtk_ecc_dt_match); -+ -+static struct platform_driver mtk_ecc_driver = { -+ .probe = mtk_ecc_probe, -+ .driver = { -+ .name = "mtk-ecc", -+ .of_match_table = of_match_ptr(mtk_ecc_dt_match), -+#ifdef CONFIG_PM_SLEEP -+ .pm = &mtk_ecc_pm_ops, -+#endif -+ }, -+}; -+ -+module_platform_driver(mtk_ecc_driver); -+ -+MODULE_AUTHOR("Xiaolei Li "); -+MODULE_DESCRIPTION("MTK Nand ECC Driver"); -+MODULE_LICENSE("Dual MIT/GPL"); ---- a/drivers/mtd/nand/raw/Kconfig -+++ b/drivers/mtd/nand/raw/Kconfig -@@ -360,6 +360,7 @@ config MTD_NAND_QCOM - - config MTD_NAND_MTK - tristate "MTK NAND controller" -+ depends on MTD_NAND_ECC_MEDIATEK - depends on ARCH_MEDIATEK || COMPILE_TEST - depends on HAS_IOMEM - help ---- a/drivers/mtd/nand/raw/Makefile -+++ b/drivers/mtd/nand/raw/Makefile -@@ -48,7 +48,7 @@ obj-$(CONFIG_MTD_NAND_SUNXI) += sunxi_n - obj-$(CONFIG_MTD_NAND_HISI504) += hisi504_nand.o - obj-$(CONFIG_MTD_NAND_BRCMNAND) += brcmnand/ - obj-$(CONFIG_MTD_NAND_QCOM) += qcom_nandc.o --obj-$(CONFIG_MTD_NAND_MTK) += mtk_ecc.o mtk_nand.o -+obj-$(CONFIG_MTD_NAND_MTK) += mtk_nand.o - obj-$(CONFIG_MTD_NAND_MXIC) += mxic_nand.o - obj-$(CONFIG_MTD_NAND_TEGRA) += tegra_nand.o - obj-$(CONFIG_MTD_NAND_STM32_FMC2) += stm32_fmc2_nand.o ---- a/drivers/mtd/nand/raw/mtk_nand.c -+++ b/drivers/mtd/nand/raw/mtk_nand.c -@@ -17,7 +17,7 @@ - #include - #include - #include --#include "mtk_ecc.h" -+#include - - /* NAND controller register definition */ - #define NFI_CNFG (0x00) ---- a/drivers/mtd/nand/raw/mtk_ecc.h -+++ /dev/null -@@ -1,47 +0,0 @@ --/* SPDX-License-Identifier: GPL-2.0 OR MIT */ --/* -- * MTK SDG1 ECC controller -- * -- * Copyright (c) 2016 Mediatek -- * Authors: Xiaolei Li -- * Jorge Ramirez-Ortiz -- */ -- --#ifndef __DRIVERS_MTD_NAND_MTK_ECC_H__ --#define __DRIVERS_MTD_NAND_MTK_ECC_H__ -- --#include -- --enum mtk_ecc_mode {ECC_DMA_MODE = 0, ECC_NFI_MODE = 1}; --enum mtk_ecc_operation {ECC_ENCODE, ECC_DECODE}; -- --struct device_node; --struct mtk_ecc; -- --struct mtk_ecc_stats { -- u32 corrected; -- u32 bitflips; -- u32 failed; --}; -- --struct mtk_ecc_config { -- enum mtk_ecc_operation op; -- enum mtk_ecc_mode mode; -- dma_addr_t addr; -- u32 strength; -- u32 sectors; -- u32 len; --}; -- --int mtk_ecc_encode(struct mtk_ecc *, struct mtk_ecc_config *, u8 *, u32); --void mtk_ecc_get_stats(struct mtk_ecc *, struct mtk_ecc_stats *, int); --int mtk_ecc_wait_done(struct mtk_ecc *, enum mtk_ecc_operation); --int mtk_ecc_enable(struct mtk_ecc *, struct mtk_ecc_config *); --void mtk_ecc_disable(struct mtk_ecc *); --void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p); --unsigned int mtk_ecc_get_parity_bits(struct mtk_ecc *ecc); -- --struct mtk_ecc *of_mtk_ecc_get(struct device_node *); --void mtk_ecc_release(struct mtk_ecc *); -- --#endif ---- /dev/null -+++ b/include/linux/mtd/nand-ecc-mtk.h -@@ -0,0 +1,47 @@ -+/* SPDX-License-Identifier: GPL-2.0 OR MIT */ -+/* -+ * MTK SDG1 ECC controller -+ * -+ * Copyright (c) 2016 Mediatek -+ * Authors: Xiaolei Li -+ * Jorge Ramirez-Ortiz -+ */ -+ -+#ifndef __DRIVERS_MTD_NAND_MTK_ECC_H__ -+#define __DRIVERS_MTD_NAND_MTK_ECC_H__ -+ -+#include -+ -+enum mtk_ecc_mode {ECC_DMA_MODE = 0, ECC_NFI_MODE = 1}; -+enum mtk_ecc_operation {ECC_ENCODE, ECC_DECODE}; -+ -+struct device_node; -+struct mtk_ecc; -+ -+struct mtk_ecc_stats { -+ u32 corrected; -+ u32 bitflips; -+ u32 failed; -+}; -+ -+struct mtk_ecc_config { -+ enum mtk_ecc_operation op; -+ enum mtk_ecc_mode mode; -+ dma_addr_t addr; -+ u32 strength; -+ u32 sectors; -+ u32 len; -+}; -+ -+int mtk_ecc_encode(struct mtk_ecc *, struct mtk_ecc_config *, u8 *, u32); -+void mtk_ecc_get_stats(struct mtk_ecc *, struct mtk_ecc_stats *, int); -+int mtk_ecc_wait_done(struct mtk_ecc *, enum mtk_ecc_operation); -+int mtk_ecc_enable(struct mtk_ecc *, struct mtk_ecc_config *); -+void mtk_ecc_disable(struct mtk_ecc *); -+void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p); -+unsigned int mtk_ecc_get_parity_bits(struct mtk_ecc *ecc); -+ -+struct mtk_ecc *of_mtk_ecc_get(struct device_node *); -+void mtk_ecc_release(struct mtk_ecc *); -+ -+#endif diff --git a/target/linux/mediatek/patches-5.15/120-12-v5.19-spi-add-driver-for-MTK-SPI-NAND-Flash-Interface.patch b/target/linux/mediatek/patches-5.15/120-12-v5.19-spi-add-driver-for-MTK-SPI-NAND-Flash-Interface.patch deleted file mode 100644 index ed20905012..0000000000 --- a/target/linux/mediatek/patches-5.15/120-12-v5.19-spi-add-driver-for-MTK-SPI-NAND-Flash-Interface.patch +++ /dev/null @@ -1,1537 +0,0 @@ -From 8170bafa8936e9fbfdce992932a63bd20eca3bc3 Mon Sep 17 00:00:00 2001 -From: Chuanhong Guo -Date: Sat, 2 Apr 2022 10:16:11 +0800 -Subject: [PATCH v6 2/5] spi: add driver for MTK SPI NAND Flash Interface - -This driver implements support for the SPI-NAND mode of MTK NAND Flash -Interface as a SPI-MEM controller with pipelined ECC capability. - -Signed-off-by: Chuanhong Guo -Tested-by: Daniel Golle ---- -Change since v1: - fix CI warnings - -Changes since v2: - use streamed DMA api to avoid an extra memory copy during read - make ECC engine config a per-nand context - take user-requested ECC strength into account - -Change since v3: none -Changes since v4: - fix missing OOB write - print page format with dev_dbg - replace uint*_t copied from vendor driver with u* - -Changes since v5: - add missing nfi mode register configuration in probe - fix an off-by-one bug in mtk_snand_mac_io - - drivers/spi/Kconfig | 10 + - drivers/spi/Makefile | 1 + - drivers/spi/spi-mtk-snfi.c | 1470 ++++++++++++++++++++++++++++++++++++ - 3 files changed, 1481 insertions(+) - create mode 100644 drivers/spi/spi-mtk-snfi.c - ---- a/drivers/spi/Kconfig -+++ b/drivers/spi/Kconfig -@@ -529,6 +529,16 @@ config SPI_MTK_NOR - SPI interface as well as several SPI NOR specific instructions - via SPI MEM interface. - -+config SPI_MTK_SNFI -+ tristate "MediaTek SPI NAND Flash Interface" -+ depends on ARCH_MEDIATEK || COMPILE_TEST -+ depends on MTD_NAND_ECC_MEDIATEK -+ help -+ This enables support for SPI-NAND mode on the MediaTek NAND -+ Flash Interface found on MediaTek ARM SoCs. This controller -+ is implemented as a SPI-MEM controller with pipelined ECC -+ capcability. -+ - config SPI_NPCM_FIU - tristate "Nuvoton NPCM FLASH Interface Unit" - depends on ARCH_NPCM || COMPILE_TEST ---- a/drivers/spi/Makefile -+++ b/drivers/spi/Makefile -@@ -71,6 +71,7 @@ obj-$(CONFIG_SPI_MPC52xx) += spi-mpc52x - obj-$(CONFIG_SPI_MT65XX) += spi-mt65xx.o - obj-$(CONFIG_SPI_MT7621) += spi-mt7621.o - obj-$(CONFIG_SPI_MTK_NOR) += spi-mtk-nor.o -+obj-$(CONFIG_SPI_MTK_SNFI) += spi-mtk-snfi.o - obj-$(CONFIG_SPI_MXIC) += spi-mxic.o - obj-$(CONFIG_SPI_MXS) += spi-mxs.o - obj-$(CONFIG_SPI_NPCM_FIU) += spi-npcm-fiu.o ---- /dev/null -+++ b/drivers/spi/spi-mtk-snfi.c -@@ -0,0 +1,1470 @@ -+// SPDX-License-Identifier: GPL-2.0 -+// -+// Driver for the SPI-NAND mode of Mediatek NAND Flash Interface -+// -+// Copyright (c) 2022 Chuanhong Guo -+// -+// This driver is based on the SPI-NAND mtd driver from Mediatek SDK: -+// -+// Copyright (C) 2020 MediaTek Inc. -+// Author: Weijie Gao -+// -+// This controller organize the page data as several interleaved sectors -+// like the following: (sizeof(FDM + ECC) = snf->nfi_cfg.spare_size) -+// +---------+------+------+---------+------+------+-----+ -+// | Sector1 | FDM1 | ECC1 | Sector2 | FDM2 | ECC2 | ... | -+// +---------+------+------+---------+------+------+-----+ -+// With auto-format turned on, DMA only returns this part: -+// +---------+---------+-----+ -+// | Sector1 | Sector2 | ... | -+// +---------+---------+-----+ -+// The FDM data will be filled to the registers, and ECC parity data isn't -+// accessible. -+// With auto-format off, all ((Sector+FDM+ECC)*nsectors) will be read over DMA -+// in it's original order shown in the first table. ECC can't be turned on when -+// auto-format is off. -+// -+// However, Linux SPI-NAND driver expects the data returned as: -+// +------+-----+ -+// | Page | OOB | -+// +------+-----+ -+// where the page data is continuously stored instead of interleaved. -+// So we assume all instructions matching the page_op template between ECC -+// prepare_io_req and finish_io_req are for page cache r/w. -+// Here's how this spi-mem driver operates when reading: -+// 1. Always set snf->autofmt = true in prepare_io_req (even when ECC is off). -+// 2. Perform page ops and let the controller fill the DMA bounce buffer with -+// de-interleaved sector data and set FDM registers. -+// 3. Return the data as: -+// +---------+---------+-----+------+------+-----+ -+// | Sector1 | Sector2 | ... | FDM1 | FDM2 | ... | -+// +---------+---------+-----+------+------+-----+ -+// 4. For other matching spi_mem ops outside a prepare/finish_io_req pair, -+// read the data with auto-format off into the bounce buffer and copy -+// needed data to the buffer specified in the request. -+// -+// Write requests operates in a similar manner. -+// As a limitation of this strategy, we won't be able to access any ECC parity -+// data at all in Linux. -+// -+// Here's the bad block mark situation on MTK chips: -+// In older chips like mt7622, MTK uses the first FDM byte in the first sector -+// as the bad block mark. After de-interleaving, this byte appears at [pagesize] -+// in the returned data, which is the BBM position expected by kernel. However, -+// the conventional bad block mark is the first byte of the OOB, which is part -+// of the last sector data in the interleaved layout. Instead of fixing their -+// hardware, MTK decided to address this inconsistency in software. On these -+// later chips, the BootROM expects the following: -+// 1. The [pagesize] byte on a nand page is used as BBM, which will appear at -+// (page_size - (nsectors - 1) * spare_size) in the DMA buffer. -+// 2. The original byte stored at that position in the DMA buffer will be stored -+// as the first byte of the FDM section in the last sector. -+// We can't disagree with the BootROM, so after de-interleaving, we need to -+// perform the following swaps in read: -+// 1. Store the BBM at [page_size - (nsectors - 1) * spare_size] to [page_size], -+// which is the expected BBM position by kernel. -+// 2. Store the page data byte at [pagesize + (nsectors-1) * fdm] back to -+// [page_size - (nsectors - 1) * spare_size] -+// Similarly, when writing, we need to perform swaps in the other direction. -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+// NFI registers -+#define NFI_CNFG 0x000 -+#define CNFG_OP_MODE_S 12 -+#define CNFG_OP_MODE_CUST 6 -+#define CNFG_OP_MODE_PROGRAM 3 -+#define CNFG_AUTO_FMT_EN BIT(9) -+#define CNFG_HW_ECC_EN BIT(8) -+#define CNFG_DMA_BURST_EN BIT(2) -+#define CNFG_READ_MODE BIT(1) -+#define CNFG_DMA_MODE BIT(0) -+ -+#define NFI_PAGEFMT 0x0004 -+#define NFI_SPARE_SIZE_LS_S 16 -+#define NFI_FDM_ECC_NUM_S 12 -+#define NFI_FDM_NUM_S 8 -+#define NFI_SPARE_SIZE_S 4 -+#define NFI_SEC_SEL_512 BIT(2) -+#define NFI_PAGE_SIZE_S 0 -+#define NFI_PAGE_SIZE_512_2K 0 -+#define NFI_PAGE_SIZE_2K_4K 1 -+#define NFI_PAGE_SIZE_4K_8K 2 -+#define NFI_PAGE_SIZE_8K_16K 3 -+ -+#define NFI_CON 0x008 -+#define CON_SEC_NUM_S 12 -+#define CON_BWR BIT(9) -+#define CON_BRD BIT(8) -+#define CON_NFI_RST BIT(1) -+#define CON_FIFO_FLUSH BIT(0) -+ -+#define NFI_INTR_EN 0x010 -+#define NFI_INTR_STA 0x014 -+#define NFI_IRQ_INTR_EN BIT(31) -+#define NFI_IRQ_CUS_READ BIT(8) -+#define NFI_IRQ_CUS_PG BIT(7) -+ -+#define NFI_CMD 0x020 -+#define NFI_CMD_DUMMY_READ 0x00 -+#define NFI_CMD_DUMMY_WRITE 0x80 -+ -+#define NFI_STRDATA 0x040 -+#define STR_DATA BIT(0) -+ -+#define NFI_STA 0x060 -+#define NFI_NAND_FSM GENMASK(28, 24) -+#define NFI_FSM GENMASK(19, 16) -+#define READ_EMPTY BIT(12) -+ -+#define NFI_FIFOSTA 0x064 -+#define FIFO_WR_REMAIN_S 8 -+#define FIFO_RD_REMAIN_S 0 -+ -+#define NFI_ADDRCNTR 0x070 -+#define SEC_CNTR GENMASK(16, 12) -+#define SEC_CNTR_S 12 -+#define NFI_SEC_CNTR(val) (((val)&SEC_CNTR) >> SEC_CNTR_S) -+ -+#define NFI_STRADDR 0x080 -+ -+#define NFI_BYTELEN 0x084 -+#define BUS_SEC_CNTR(val) (((val)&SEC_CNTR) >> SEC_CNTR_S) -+ -+#define NFI_FDM0L 0x0a0 -+#define NFI_FDM0M 0x0a4 -+#define NFI_FDML(n) (NFI_FDM0L + (n)*8) -+#define NFI_FDMM(n) (NFI_FDM0M + (n)*8) -+ -+#define NFI_DEBUG_CON1 0x220 -+#define WBUF_EN BIT(2) -+ -+#define NFI_MASTERSTA 0x224 -+#define MAS_ADDR GENMASK(11, 9) -+#define MAS_RD GENMASK(8, 6) -+#define MAS_WR GENMASK(5, 3) -+#define MAS_RDDLY GENMASK(2, 0) -+#define NFI_MASTERSTA_MASK_7622 (MAS_ADDR | MAS_RD | MAS_WR | MAS_RDDLY) -+ -+// SNFI registers -+#define SNF_MAC_CTL 0x500 -+#define MAC_XIO_SEL BIT(4) -+#define SF_MAC_EN BIT(3) -+#define SF_TRIG BIT(2) -+#define WIP_READY BIT(1) -+#define WIP BIT(0) -+ -+#define SNF_MAC_OUTL 0x504 -+#define SNF_MAC_INL 0x508 -+ -+#define SNF_RD_CTL2 0x510 -+#define DATA_READ_DUMMY_S 8 -+#define DATA_READ_MAX_DUMMY 0xf -+#define DATA_READ_CMD_S 0 -+ -+#define SNF_RD_CTL3 0x514 -+ -+#define SNF_PG_CTL1 0x524 -+#define PG_LOAD_CMD_S 8 -+ -+#define SNF_PG_CTL2 0x528 -+ -+#define SNF_MISC_CTL 0x538 -+#define SW_RST BIT(28) -+#define FIFO_RD_LTC_S 25 -+#define PG_LOAD_X4_EN BIT(20) -+#define DATA_READ_MODE_S 16 -+#define DATA_READ_MODE GENMASK(18, 16) -+#define DATA_READ_MODE_X1 0 -+#define DATA_READ_MODE_X2 1 -+#define DATA_READ_MODE_X4 2 -+#define DATA_READ_MODE_DUAL 5 -+#define DATA_READ_MODE_QUAD 6 -+#define PG_LOAD_CUSTOM_EN BIT(7) -+#define DATARD_CUSTOM_EN BIT(6) -+#define CS_DESELECT_CYC_S 0 -+ -+#define SNF_MISC_CTL2 0x53c -+#define PROGRAM_LOAD_BYTE_NUM_S 16 -+#define READ_DATA_BYTE_NUM_S 11 -+ -+#define SNF_DLY_CTL3 0x548 -+#define SFCK_SAM_DLY_S 0 -+ -+#define SNF_STA_CTL1 0x550 -+#define CUS_PG_DONE BIT(28) -+#define CUS_READ_DONE BIT(27) -+#define SPI_STATE_S 0 -+#define SPI_STATE GENMASK(3, 0) -+ -+#define SNF_CFG 0x55c -+#define SPI_MODE BIT(0) -+ -+#define SNF_GPRAM 0x800 -+#define SNF_GPRAM_SIZE 0xa0 -+ -+#define SNFI_POLL_INTERVAL 1000000 -+ -+static const u8 mt7622_spare_sizes[] = { 16, 26, 27, 28 }; -+ -+struct mtk_snand_caps { -+ u16 sector_size; -+ u16 max_sectors; -+ u16 fdm_size; -+ u16 fdm_ecc_size; -+ u16 fifo_size; -+ -+ bool bbm_swap; -+ bool empty_page_check; -+ u32 mastersta_mask; -+ -+ const u8 *spare_sizes; -+ u32 num_spare_size; -+}; -+ -+static const struct mtk_snand_caps mt7622_snand_caps = { -+ .sector_size = 512, -+ .max_sectors = 8, -+ .fdm_size = 8, -+ .fdm_ecc_size = 1, -+ .fifo_size = 32, -+ .bbm_swap = false, -+ .empty_page_check = false, -+ .mastersta_mask = NFI_MASTERSTA_MASK_7622, -+ .spare_sizes = mt7622_spare_sizes, -+ .num_spare_size = ARRAY_SIZE(mt7622_spare_sizes) -+}; -+ -+static const struct mtk_snand_caps mt7629_snand_caps = { -+ .sector_size = 512, -+ .max_sectors = 8, -+ .fdm_size = 8, -+ .fdm_ecc_size = 1, -+ .fifo_size = 32, -+ .bbm_swap = true, -+ .empty_page_check = false, -+ .mastersta_mask = NFI_MASTERSTA_MASK_7622, -+ .spare_sizes = mt7622_spare_sizes, -+ .num_spare_size = ARRAY_SIZE(mt7622_spare_sizes) -+}; -+ -+struct mtk_snand_conf { -+ size_t page_size; -+ size_t oob_size; -+ u8 nsectors; -+ u8 spare_size; -+}; -+ -+struct mtk_snand { -+ struct spi_controller *ctlr; -+ struct device *dev; -+ struct clk *nfi_clk; -+ struct clk *pad_clk; -+ void __iomem *nfi_base; -+ int irq; -+ struct completion op_done; -+ const struct mtk_snand_caps *caps; -+ struct mtk_ecc_config *ecc_cfg; -+ struct mtk_ecc *ecc; -+ struct mtk_snand_conf nfi_cfg; -+ struct mtk_ecc_stats ecc_stats; -+ struct nand_ecc_engine ecc_eng; -+ bool autofmt; -+ u8 *buf; -+ size_t buf_len; -+}; -+ -+static struct mtk_snand *nand_to_mtk_snand(struct nand_device *nand) -+{ -+ struct nand_ecc_engine *eng = nand->ecc.engine; -+ -+ return container_of(eng, struct mtk_snand, ecc_eng); -+} -+ -+static inline int snand_prepare_bouncebuf(struct mtk_snand *snf, size_t size) -+{ -+ if (snf->buf_len >= size) -+ return 0; -+ kfree(snf->buf); -+ snf->buf = kmalloc(size, GFP_KERNEL); -+ if (!snf->buf) -+ return -ENOMEM; -+ snf->buf_len = size; -+ memset(snf->buf, 0xff, snf->buf_len); -+ return 0; -+} -+ -+static inline u32 nfi_read32(struct mtk_snand *snf, u32 reg) -+{ -+ return readl(snf->nfi_base + reg); -+} -+ -+static inline void nfi_write32(struct mtk_snand *snf, u32 reg, u32 val) -+{ -+ writel(val, snf->nfi_base + reg); -+} -+ -+static inline void nfi_write16(struct mtk_snand *snf, u32 reg, u16 val) -+{ -+ writew(val, snf->nfi_base + reg); -+} -+ -+static inline void nfi_rmw32(struct mtk_snand *snf, u32 reg, u32 clr, u32 set) -+{ -+ u32 val; -+ -+ val = readl(snf->nfi_base + reg); -+ val &= ~clr; -+ val |= set; -+ writel(val, snf->nfi_base + reg); -+} -+ -+static void nfi_read_data(struct mtk_snand *snf, u32 reg, u8 *data, u32 len) -+{ -+ u32 i, val = 0, es = sizeof(u32); -+ -+ for (i = reg; i < reg + len; i++) { -+ if (i == reg || i % es == 0) -+ val = nfi_read32(snf, i & ~(es - 1)); -+ -+ *data++ = (u8)(val >> (8 * (i % es))); -+ } -+} -+ -+static int mtk_nfi_reset(struct mtk_snand *snf) -+{ -+ u32 val, fifo_mask; -+ int ret; -+ -+ nfi_write32(snf, NFI_CON, CON_FIFO_FLUSH | CON_NFI_RST); -+ -+ ret = readw_poll_timeout(snf->nfi_base + NFI_MASTERSTA, val, -+ !(val & snf->caps->mastersta_mask), 0, -+ SNFI_POLL_INTERVAL); -+ if (ret) { -+ dev_err(snf->dev, "NFI master is still busy after reset\n"); -+ return ret; -+ } -+ -+ ret = readl_poll_timeout(snf->nfi_base + NFI_STA, val, -+ !(val & (NFI_FSM | NFI_NAND_FSM)), 0, -+ SNFI_POLL_INTERVAL); -+ if (ret) { -+ dev_err(snf->dev, "Failed to reset NFI\n"); -+ return ret; -+ } -+ -+ fifo_mask = ((snf->caps->fifo_size - 1) << FIFO_RD_REMAIN_S) | -+ ((snf->caps->fifo_size - 1) << FIFO_WR_REMAIN_S); -+ ret = readw_poll_timeout(snf->nfi_base + NFI_FIFOSTA, val, -+ !(val & fifo_mask), 0, SNFI_POLL_INTERVAL); -+ if (ret) { -+ dev_err(snf->dev, "NFI FIFOs are not empty\n"); -+ return ret; -+ } -+ -+ return 0; -+} -+ -+static int mtk_snand_mac_reset(struct mtk_snand *snf) -+{ -+ int ret; -+ u32 val; -+ -+ nfi_rmw32(snf, SNF_MISC_CTL, 0, SW_RST); -+ -+ ret = readl_poll_timeout(snf->nfi_base + SNF_STA_CTL1, val, -+ !(val & SPI_STATE), 0, SNFI_POLL_INTERVAL); -+ if (ret) -+ dev_err(snf->dev, "Failed to reset SNFI MAC\n"); -+ -+ nfi_write32(snf, SNF_MISC_CTL, -+ (2 << FIFO_RD_LTC_S) | (10 << CS_DESELECT_CYC_S)); -+ -+ return ret; -+} -+ -+static int mtk_snand_mac_trigger(struct mtk_snand *snf, u32 outlen, u32 inlen) -+{ -+ int ret; -+ u32 val; -+ -+ nfi_write32(snf, SNF_MAC_CTL, SF_MAC_EN); -+ nfi_write32(snf, SNF_MAC_OUTL, outlen); -+ nfi_write32(snf, SNF_MAC_INL, inlen); -+ -+ nfi_write32(snf, SNF_MAC_CTL, SF_MAC_EN | SF_TRIG); -+ -+ ret = readl_poll_timeout(snf->nfi_base + SNF_MAC_CTL, val, -+ val & WIP_READY, 0, SNFI_POLL_INTERVAL); -+ if (ret) { -+ dev_err(snf->dev, "Timed out waiting for WIP_READY\n"); -+ goto cleanup; -+ } -+ -+ ret = readl_poll_timeout(snf->nfi_base + SNF_MAC_CTL, val, !(val & WIP), -+ 0, SNFI_POLL_INTERVAL); -+ if (ret) -+ dev_err(snf->dev, "Timed out waiting for WIP cleared\n"); -+ -+cleanup: -+ nfi_write32(snf, SNF_MAC_CTL, 0); -+ -+ return ret; -+} -+ -+static int mtk_snand_mac_io(struct mtk_snand *snf, const struct spi_mem_op *op) -+{ -+ u32 rx_len = 0; -+ u32 reg_offs = 0; -+ u32 val = 0; -+ const u8 *tx_buf = NULL; -+ u8 *rx_buf = NULL; -+ int i, ret; -+ u8 b; -+ -+ if (op->data.dir == SPI_MEM_DATA_IN) { -+ rx_len = op->data.nbytes; -+ rx_buf = op->data.buf.in; -+ } else { -+ tx_buf = op->data.buf.out; -+ } -+ -+ mtk_snand_mac_reset(snf); -+ -+ for (i = 0; i < op->cmd.nbytes; i++, reg_offs++) { -+ b = (op->cmd.opcode >> ((op->cmd.nbytes - i - 1) * 8)) & 0xff; -+ val |= b << (8 * (reg_offs % 4)); -+ if (reg_offs % 4 == 3) { -+ nfi_write32(snf, SNF_GPRAM + reg_offs - 3, val); -+ val = 0; -+ } -+ } -+ -+ for (i = 0; i < op->addr.nbytes; i++, reg_offs++) { -+ b = (op->addr.val >> ((op->addr.nbytes - i - 1) * 8)) & 0xff; -+ val |= b << (8 * (reg_offs % 4)); -+ if (reg_offs % 4 == 3) { -+ nfi_write32(snf, SNF_GPRAM + reg_offs - 3, val); -+ val = 0; -+ } -+ } -+ -+ for (i = 0; i < op->dummy.nbytes; i++, reg_offs++) { -+ if (reg_offs % 4 == 3) { -+ nfi_write32(snf, SNF_GPRAM + reg_offs - 3, val); -+ val = 0; -+ } -+ } -+ -+ if (op->data.dir == SPI_MEM_DATA_OUT) { -+ for (i = 0; i < op->data.nbytes; i++, reg_offs++) { -+ val |= tx_buf[i] << (8 * (reg_offs % 4)); -+ if (reg_offs % 4 == 3) { -+ nfi_write32(snf, SNF_GPRAM + reg_offs - 3, val); -+ val = 0; -+ } -+ } -+ } -+ -+ if (reg_offs % 4) -+ nfi_write32(snf, SNF_GPRAM + (reg_offs & ~3), val); -+ -+ for (i = 0; i < reg_offs; i += 4) -+ dev_dbg(snf->dev, "%d: %08X", i, -+ nfi_read32(snf, SNF_GPRAM + i)); -+ -+ dev_dbg(snf->dev, "SNF TX: %u RX: %u", reg_offs, rx_len); -+ -+ ret = mtk_snand_mac_trigger(snf, reg_offs, rx_len); -+ if (ret) -+ return ret; -+ -+ if (!rx_len) -+ return 0; -+ -+ nfi_read_data(snf, SNF_GPRAM + reg_offs, rx_buf, rx_len); -+ return 0; -+} -+ -+static int mtk_snand_setup_pagefmt(struct mtk_snand *snf, u32 page_size, -+ u32 oob_size) -+{ -+ int spare_idx = -1; -+ u32 spare_size, spare_size_shift, pagesize_idx; -+ u32 sector_size_512; -+ u8 nsectors; -+ int i; -+ -+ // skip if it's already configured as required. -+ if (snf->nfi_cfg.page_size == page_size && -+ snf->nfi_cfg.oob_size == oob_size) -+ return 0; -+ -+ nsectors = page_size / snf->caps->sector_size; -+ if (nsectors > snf->caps->max_sectors) { -+ dev_err(snf->dev, "too many sectors required.\n"); -+ goto err; -+ } -+ -+ if (snf->caps->sector_size == 512) { -+ sector_size_512 = NFI_SEC_SEL_512; -+ spare_size_shift = NFI_SPARE_SIZE_S; -+ } else { -+ sector_size_512 = 0; -+ spare_size_shift = NFI_SPARE_SIZE_LS_S; -+ } -+ -+ switch (page_size) { -+ case SZ_512: -+ pagesize_idx = NFI_PAGE_SIZE_512_2K; -+ break; -+ case SZ_2K: -+ if (snf->caps->sector_size == 512) -+ pagesize_idx = NFI_PAGE_SIZE_2K_4K; -+ else -+ pagesize_idx = NFI_PAGE_SIZE_512_2K; -+ break; -+ case SZ_4K: -+ if (snf->caps->sector_size == 512) -+ pagesize_idx = NFI_PAGE_SIZE_4K_8K; -+ else -+ pagesize_idx = NFI_PAGE_SIZE_2K_4K; -+ break; -+ case SZ_8K: -+ if (snf->caps->sector_size == 512) -+ pagesize_idx = NFI_PAGE_SIZE_8K_16K; -+ else -+ pagesize_idx = NFI_PAGE_SIZE_4K_8K; -+ break; -+ case SZ_16K: -+ pagesize_idx = NFI_PAGE_SIZE_8K_16K; -+ break; -+ default: -+ dev_err(snf->dev, "unsupported page size.\n"); -+ goto err; -+ } -+ -+ spare_size = oob_size / nsectors; -+ // If we're using the 1KB sector size, HW will automatically double the -+ // spare size. We should only use half of the value in this case. -+ if (snf->caps->sector_size == 1024) -+ spare_size /= 2; -+ -+ for (i = snf->caps->num_spare_size - 1; i >= 0; i--) { -+ if (snf->caps->spare_sizes[i] <= spare_size) { -+ spare_size = snf->caps->spare_sizes[i]; -+ if (snf->caps->sector_size == 1024) -+ spare_size *= 2; -+ spare_idx = i; -+ break; -+ } -+ } -+ -+ if (spare_idx < 0) { -+ dev_err(snf->dev, "unsupported spare size: %u\n", spare_size); -+ goto err; -+ } -+ -+ nfi_write32(snf, NFI_PAGEFMT, -+ (snf->caps->fdm_ecc_size << NFI_FDM_ECC_NUM_S) | -+ (snf->caps->fdm_size << NFI_FDM_NUM_S) | -+ (spare_idx << spare_size_shift) | -+ (pagesize_idx << NFI_PAGE_SIZE_S) | -+ sector_size_512); -+ -+ snf->nfi_cfg.page_size = page_size; -+ snf->nfi_cfg.oob_size = oob_size; -+ snf->nfi_cfg.nsectors = nsectors; -+ snf->nfi_cfg.spare_size = spare_size; -+ -+ dev_dbg(snf->dev, "page format: (%u + %u) * %u\n", -+ snf->caps->sector_size, spare_size, nsectors); -+ return snand_prepare_bouncebuf(snf, page_size + oob_size); -+err: -+ dev_err(snf->dev, "page size %u + %u is not supported\n", page_size, -+ oob_size); -+ return -EOPNOTSUPP; -+} -+ -+static int mtk_snand_ooblayout_ecc(struct mtd_info *mtd, int section, -+ struct mtd_oob_region *oobecc) -+{ -+ // ECC area is not accessible -+ return -ERANGE; -+} -+ -+static int mtk_snand_ooblayout_free(struct mtd_info *mtd, int section, -+ struct mtd_oob_region *oobfree) -+{ -+ struct nand_device *nand = mtd_to_nanddev(mtd); -+ struct mtk_snand *ms = nand_to_mtk_snand(nand); -+ -+ if (section >= ms->nfi_cfg.nsectors) -+ return -ERANGE; -+ -+ oobfree->length = ms->caps->fdm_size - 1; -+ oobfree->offset = section * ms->caps->fdm_size + 1; -+ return 0; -+} -+ -+static const struct mtd_ooblayout_ops mtk_snand_ooblayout = { -+ .ecc = mtk_snand_ooblayout_ecc, -+ .free = mtk_snand_ooblayout_free, -+}; -+ -+static int mtk_snand_ecc_init_ctx(struct nand_device *nand) -+{ -+ struct mtk_snand *snf = nand_to_mtk_snand(nand); -+ struct nand_ecc_props *conf = &nand->ecc.ctx.conf; -+ struct nand_ecc_props *reqs = &nand->ecc.requirements; -+ struct nand_ecc_props *user = &nand->ecc.user_conf; -+ struct mtd_info *mtd = nanddev_to_mtd(nand); -+ int step_size = 0, strength = 0, desired_correction = 0, steps; -+ bool ecc_user = false; -+ int ret; -+ u32 parity_bits, max_ecc_bytes; -+ struct mtk_ecc_config *ecc_cfg; -+ -+ ret = mtk_snand_setup_pagefmt(snf, nand->memorg.pagesize, -+ nand->memorg.oobsize); -+ if (ret) -+ return ret; -+ -+ ecc_cfg = kzalloc(sizeof(*ecc_cfg), GFP_KERNEL); -+ if (!ecc_cfg) -+ return -ENOMEM; -+ -+ nand->ecc.ctx.priv = ecc_cfg; -+ -+ if (user->step_size && user->strength) { -+ step_size = user->step_size; -+ strength = user->strength; -+ ecc_user = true; -+ } else if (reqs->step_size && reqs->strength) { -+ step_size = reqs->step_size; -+ strength = reqs->strength; -+ } -+ -+ if (step_size && strength) { -+ steps = mtd->writesize / step_size; -+ desired_correction = steps * strength; -+ strength = desired_correction / snf->nfi_cfg.nsectors; -+ } -+ -+ ecc_cfg->mode = ECC_NFI_MODE; -+ ecc_cfg->sectors = snf->nfi_cfg.nsectors; -+ ecc_cfg->len = snf->caps->sector_size + snf->caps->fdm_ecc_size; -+ -+ // calculate the max possible strength under current page format -+ parity_bits = mtk_ecc_get_parity_bits(snf->ecc); -+ max_ecc_bytes = snf->nfi_cfg.spare_size - snf->caps->fdm_size; -+ ecc_cfg->strength = max_ecc_bytes * 8 / parity_bits; -+ mtk_ecc_adjust_strength(snf->ecc, &ecc_cfg->strength); -+ -+ // if there's a user requested strength, find the minimum strength that -+ // meets the requirement. Otherwise use the maximum strength which is -+ // expected by BootROM. -+ if (ecc_user && strength) { -+ u32 s_next = ecc_cfg->strength - 1; -+ -+ while (1) { -+ mtk_ecc_adjust_strength(snf->ecc, &s_next); -+ if (s_next >= ecc_cfg->strength) -+ break; -+ if (s_next < strength) -+ break; -+ s_next = ecc_cfg->strength - 1; -+ } -+ } -+ -+ mtd_set_ooblayout(mtd, &mtk_snand_ooblayout); -+ -+ conf->step_size = snf->caps->sector_size; -+ conf->strength = ecc_cfg->strength; -+ -+ if (ecc_cfg->strength < strength) -+ dev_warn(snf->dev, "unable to fulfill ECC of %u bits.\n", -+ strength); -+ dev_info(snf->dev, "ECC strength: %u bits per %u bytes\n", -+ ecc_cfg->strength, snf->caps->sector_size); -+ -+ return 0; -+} -+ -+static void mtk_snand_ecc_cleanup_ctx(struct nand_device *nand) -+{ -+ struct mtk_ecc_config *ecc_cfg = nand_to_ecc_ctx(nand); -+ -+ kfree(ecc_cfg); -+} -+ -+static int mtk_snand_ecc_prepare_io_req(struct nand_device *nand, -+ struct nand_page_io_req *req) -+{ -+ struct mtk_snand *snf = nand_to_mtk_snand(nand); -+ struct mtk_ecc_config *ecc_cfg = nand_to_ecc_ctx(nand); -+ int ret; -+ -+ ret = mtk_snand_setup_pagefmt(snf, nand->memorg.pagesize, -+ nand->memorg.oobsize); -+ if (ret) -+ return ret; -+ snf->autofmt = true; -+ snf->ecc_cfg = ecc_cfg; -+ return 0; -+} -+ -+static int mtk_snand_ecc_finish_io_req(struct nand_device *nand, -+ struct nand_page_io_req *req) -+{ -+ struct mtk_snand *snf = nand_to_mtk_snand(nand); -+ struct mtd_info *mtd = nanddev_to_mtd(nand); -+ -+ snf->ecc_cfg = NULL; -+ snf->autofmt = false; -+ if ((req->mode == MTD_OPS_RAW) || (req->type != NAND_PAGE_READ)) -+ return 0; -+ -+ if (snf->ecc_stats.failed) -+ mtd->ecc_stats.failed += snf->ecc_stats.failed; -+ mtd->ecc_stats.corrected += snf->ecc_stats.corrected; -+ return snf->ecc_stats.failed ? -EBADMSG : snf->ecc_stats.bitflips; -+} -+ -+static struct nand_ecc_engine_ops mtk_snfi_ecc_engine_ops = { -+ .init_ctx = mtk_snand_ecc_init_ctx, -+ .cleanup_ctx = mtk_snand_ecc_cleanup_ctx, -+ .prepare_io_req = mtk_snand_ecc_prepare_io_req, -+ .finish_io_req = mtk_snand_ecc_finish_io_req, -+}; -+ -+static void mtk_snand_read_fdm(struct mtk_snand *snf, u8 *buf) -+{ -+ u32 vall, valm; -+ u8 *oobptr = buf; -+ int i, j; -+ -+ for (i = 0; i < snf->nfi_cfg.nsectors; i++) { -+ vall = nfi_read32(snf, NFI_FDML(i)); -+ valm = nfi_read32(snf, NFI_FDMM(i)); -+ -+ for (j = 0; j < snf->caps->fdm_size; j++) -+ oobptr[j] = (j >= 4 ? valm : vall) >> ((j % 4) * 8); -+ -+ oobptr += snf->caps->fdm_size; -+ } -+} -+ -+static void mtk_snand_write_fdm(struct mtk_snand *snf, const u8 *buf) -+{ -+ u32 fdm_size = snf->caps->fdm_size; -+ const u8 *oobptr = buf; -+ u32 vall, valm; -+ int i, j; -+ -+ for (i = 0; i < snf->nfi_cfg.nsectors; i++) { -+ vall = 0; -+ valm = 0; -+ -+ for (j = 0; j < 8; j++) { -+ if (j < 4) -+ vall |= (j < fdm_size ? oobptr[j] : 0xff) -+ << (j * 8); -+ else -+ valm |= (j < fdm_size ? oobptr[j] : 0xff) -+ << ((j - 4) * 8); -+ } -+ -+ nfi_write32(snf, NFI_FDML(i), vall); -+ nfi_write32(snf, NFI_FDMM(i), valm); -+ -+ oobptr += fdm_size; -+ } -+} -+ -+static void mtk_snand_bm_swap(struct mtk_snand *snf, u8 *buf) -+{ -+ u32 buf_bbm_pos, fdm_bbm_pos; -+ -+ if (!snf->caps->bbm_swap || snf->nfi_cfg.nsectors == 1) -+ return; -+ -+ // swap [pagesize] byte on nand with the first fdm byte -+ // in the last sector. -+ buf_bbm_pos = snf->nfi_cfg.page_size - -+ (snf->nfi_cfg.nsectors - 1) * snf->nfi_cfg.spare_size; -+ fdm_bbm_pos = snf->nfi_cfg.page_size + -+ (snf->nfi_cfg.nsectors - 1) * snf->caps->fdm_size; -+ -+ swap(snf->buf[fdm_bbm_pos], buf[buf_bbm_pos]); -+} -+ -+static void mtk_snand_fdm_bm_swap(struct mtk_snand *snf) -+{ -+ u32 fdm_bbm_pos1, fdm_bbm_pos2; -+ -+ if (!snf->caps->bbm_swap || snf->nfi_cfg.nsectors == 1) -+ return; -+ -+ // swap the first fdm byte in the first and the last sector. -+ fdm_bbm_pos1 = snf->nfi_cfg.page_size; -+ fdm_bbm_pos2 = snf->nfi_cfg.page_size + -+ (snf->nfi_cfg.nsectors - 1) * snf->caps->fdm_size; -+ swap(snf->buf[fdm_bbm_pos1], snf->buf[fdm_bbm_pos2]); -+} -+ -+static int mtk_snand_read_page_cache(struct mtk_snand *snf, -+ const struct spi_mem_op *op) -+{ -+ u8 *buf = snf->buf; -+ u8 *buf_fdm = buf + snf->nfi_cfg.page_size; -+ // the address part to be sent by the controller -+ u32 op_addr = op->addr.val; -+ // where to start copying data from bounce buffer -+ u32 rd_offset = 0; -+ u32 dummy_clk = (op->dummy.nbytes * BITS_PER_BYTE / op->dummy.buswidth); -+ u32 op_mode = 0; -+ u32 dma_len = snf->buf_len; -+ int ret = 0; -+ u32 rd_mode, rd_bytes, val; -+ dma_addr_t buf_dma; -+ -+ if (snf->autofmt) { -+ u32 last_bit; -+ u32 mask; -+ -+ dma_len = snf->nfi_cfg.page_size; -+ op_mode = CNFG_AUTO_FMT_EN; -+ if (op->data.ecc) -+ op_mode |= CNFG_HW_ECC_EN; -+ // extract the plane bit: -+ // Find the highest bit set in (pagesize+oobsize). -+ // Bits higher than that in op->addr are kept and sent over SPI -+ // Lower bits are used as an offset for copying data from DMA -+ // bounce buffer. -+ last_bit = fls(snf->nfi_cfg.page_size + snf->nfi_cfg.oob_size); -+ mask = (1 << last_bit) - 1; -+ rd_offset = op_addr & mask; -+ op_addr &= ~mask; -+ -+ // check if we can dma to the caller memory -+ if (rd_offset == 0 && op->data.nbytes >= snf->nfi_cfg.page_size) -+ buf = op->data.buf.in; -+ } -+ mtk_snand_mac_reset(snf); -+ mtk_nfi_reset(snf); -+ -+ // command and dummy cycles -+ nfi_write32(snf, SNF_RD_CTL2, -+ (dummy_clk << DATA_READ_DUMMY_S) | -+ (op->cmd.opcode << DATA_READ_CMD_S)); -+ -+ // read address -+ nfi_write32(snf, SNF_RD_CTL3, op_addr); -+ -+ // Set read op_mode -+ if (op->data.buswidth == 4) -+ rd_mode = op->addr.buswidth == 4 ? DATA_READ_MODE_QUAD : -+ DATA_READ_MODE_X4; -+ else if (op->data.buswidth == 2) -+ rd_mode = op->addr.buswidth == 2 ? DATA_READ_MODE_DUAL : -+ DATA_READ_MODE_X2; -+ else -+ rd_mode = DATA_READ_MODE_X1; -+ rd_mode <<= DATA_READ_MODE_S; -+ nfi_rmw32(snf, SNF_MISC_CTL, DATA_READ_MODE, -+ rd_mode | DATARD_CUSTOM_EN); -+ -+ // Set bytes to read -+ rd_bytes = (snf->nfi_cfg.spare_size + snf->caps->sector_size) * -+ snf->nfi_cfg.nsectors; -+ nfi_write32(snf, SNF_MISC_CTL2, -+ (rd_bytes << PROGRAM_LOAD_BYTE_NUM_S) | rd_bytes); -+ -+ // NFI read prepare -+ nfi_write16(snf, NFI_CNFG, -+ (CNFG_OP_MODE_CUST << CNFG_OP_MODE_S) | CNFG_DMA_BURST_EN | -+ CNFG_READ_MODE | CNFG_DMA_MODE | op_mode); -+ -+ nfi_write32(snf, NFI_CON, (snf->nfi_cfg.nsectors << CON_SEC_NUM_S)); -+ -+ buf_dma = dma_map_single(snf->dev, buf, dma_len, DMA_FROM_DEVICE); -+ if (dma_mapping_error(snf->dev, buf_dma)) { -+ dev_err(snf->dev, "DMA mapping failed.\n"); -+ goto cleanup; -+ } -+ nfi_write32(snf, NFI_STRADDR, buf_dma); -+ if (op->data.ecc) { -+ snf->ecc_cfg->op = ECC_DECODE; -+ ret = mtk_ecc_enable(snf->ecc, snf->ecc_cfg); -+ if (ret) -+ goto cleanup_dma; -+ } -+ // Prepare for custom read interrupt -+ nfi_write32(snf, NFI_INTR_EN, NFI_IRQ_INTR_EN | NFI_IRQ_CUS_READ); -+ reinit_completion(&snf->op_done); -+ -+ // Trigger NFI into custom mode -+ nfi_write16(snf, NFI_CMD, NFI_CMD_DUMMY_READ); -+ -+ // Start DMA read -+ nfi_rmw32(snf, NFI_CON, 0, CON_BRD); -+ nfi_write16(snf, NFI_STRDATA, STR_DATA); -+ -+ if (!wait_for_completion_timeout( -+ &snf->op_done, usecs_to_jiffies(SNFI_POLL_INTERVAL))) { -+ dev_err(snf->dev, "DMA timed out for reading from cache.\n"); -+ ret = -ETIMEDOUT; -+ goto cleanup; -+ } -+ -+ // Wait for BUS_SEC_CNTR returning expected value -+ ret = readl_poll_timeout(snf->nfi_base + NFI_BYTELEN, val, -+ BUS_SEC_CNTR(val) >= snf->nfi_cfg.nsectors, 0, -+ SNFI_POLL_INTERVAL); -+ if (ret) { -+ dev_err(snf->dev, "Timed out waiting for BUS_SEC_CNTR\n"); -+ goto cleanup2; -+ } -+ -+ // Wait for bus becoming idle -+ ret = readl_poll_timeout(snf->nfi_base + NFI_MASTERSTA, val, -+ !(val & snf->caps->mastersta_mask), 0, -+ SNFI_POLL_INTERVAL); -+ if (ret) { -+ dev_err(snf->dev, "Timed out waiting for bus becoming idle\n"); -+ goto cleanup2; -+ } -+ -+ if (op->data.ecc) { -+ ret = mtk_ecc_wait_done(snf->ecc, ECC_DECODE); -+ if (ret) { -+ dev_err(snf->dev, "wait ecc done timeout\n"); -+ goto cleanup2; -+ } -+ // save status before disabling ecc -+ mtk_ecc_get_stats(snf->ecc, &snf->ecc_stats, -+ snf->nfi_cfg.nsectors); -+ } -+ -+ dma_unmap_single(snf->dev, buf_dma, dma_len, DMA_FROM_DEVICE); -+ -+ if (snf->autofmt) { -+ mtk_snand_read_fdm(snf, buf_fdm); -+ if (snf->caps->bbm_swap) { -+ mtk_snand_bm_swap(snf, buf); -+ mtk_snand_fdm_bm_swap(snf); -+ } -+ } -+ -+ // copy data back -+ if (nfi_read32(snf, NFI_STA) & READ_EMPTY) { -+ memset(op->data.buf.in, 0xff, op->data.nbytes); -+ snf->ecc_stats.bitflips = 0; -+ snf->ecc_stats.failed = 0; -+ snf->ecc_stats.corrected = 0; -+ } else { -+ if (buf == op->data.buf.in) { -+ u32 cap_len = snf->buf_len - snf->nfi_cfg.page_size; -+ u32 req_left = op->data.nbytes - snf->nfi_cfg.page_size; -+ -+ if (req_left) -+ memcpy(op->data.buf.in + snf->nfi_cfg.page_size, -+ buf_fdm, -+ cap_len < req_left ? cap_len : req_left); -+ } else if (rd_offset < snf->buf_len) { -+ u32 cap_len = snf->buf_len - rd_offset; -+ -+ if (op->data.nbytes < cap_len) -+ cap_len = op->data.nbytes; -+ memcpy(op->data.buf.in, snf->buf + rd_offset, cap_len); -+ } -+ } -+cleanup2: -+ if (op->data.ecc) -+ mtk_ecc_disable(snf->ecc); -+cleanup_dma: -+ // unmap dma only if any error happens. (otherwise it's done before -+ // data copying) -+ if (ret) -+ dma_unmap_single(snf->dev, buf_dma, dma_len, DMA_FROM_DEVICE); -+cleanup: -+ // Stop read -+ nfi_write32(snf, NFI_CON, 0); -+ nfi_write16(snf, NFI_CNFG, 0); -+ -+ // Clear SNF done flag -+ nfi_rmw32(snf, SNF_STA_CTL1, 0, CUS_READ_DONE); -+ nfi_write32(snf, SNF_STA_CTL1, 0); -+ -+ // Disable interrupt -+ nfi_read32(snf, NFI_INTR_STA); -+ nfi_write32(snf, NFI_INTR_EN, 0); -+ -+ nfi_rmw32(snf, SNF_MISC_CTL, DATARD_CUSTOM_EN, 0); -+ return ret; -+} -+ -+static int mtk_snand_write_page_cache(struct mtk_snand *snf, -+ const struct spi_mem_op *op) -+{ -+ // the address part to be sent by the controller -+ u32 op_addr = op->addr.val; -+ // where to start copying data from bounce buffer -+ u32 wr_offset = 0; -+ u32 op_mode = 0; -+ int ret = 0; -+ u32 wr_mode = 0; -+ u32 dma_len = snf->buf_len; -+ u32 wr_bytes, val; -+ size_t cap_len; -+ dma_addr_t buf_dma; -+ -+ if (snf->autofmt) { -+ u32 last_bit; -+ u32 mask; -+ -+ dma_len = snf->nfi_cfg.page_size; -+ op_mode = CNFG_AUTO_FMT_EN; -+ if (op->data.ecc) -+ op_mode |= CNFG_HW_ECC_EN; -+ -+ last_bit = fls(snf->nfi_cfg.page_size + snf->nfi_cfg.oob_size); -+ mask = (1 << last_bit) - 1; -+ wr_offset = op_addr & mask; -+ op_addr &= ~mask; -+ } -+ mtk_snand_mac_reset(snf); -+ mtk_nfi_reset(snf); -+ -+ if (wr_offset) -+ memset(snf->buf, 0xff, wr_offset); -+ -+ cap_len = snf->buf_len - wr_offset; -+ if (op->data.nbytes < cap_len) -+ cap_len = op->data.nbytes; -+ memcpy(snf->buf + wr_offset, op->data.buf.out, cap_len); -+ if (snf->autofmt) { -+ if (snf->caps->bbm_swap) { -+ mtk_snand_fdm_bm_swap(snf); -+ mtk_snand_bm_swap(snf, snf->buf); -+ } -+ mtk_snand_write_fdm(snf, snf->buf + snf->nfi_cfg.page_size); -+ } -+ -+ // Command -+ nfi_write32(snf, SNF_PG_CTL1, (op->cmd.opcode << PG_LOAD_CMD_S)); -+ -+ // write address -+ nfi_write32(snf, SNF_PG_CTL2, op_addr); -+ -+ // Set read op_mode -+ if (op->data.buswidth == 4) -+ wr_mode = PG_LOAD_X4_EN; -+ -+ nfi_rmw32(snf, SNF_MISC_CTL, PG_LOAD_X4_EN, -+ wr_mode | PG_LOAD_CUSTOM_EN); -+ -+ // Set bytes to write -+ wr_bytes = (snf->nfi_cfg.spare_size + snf->caps->sector_size) * -+ snf->nfi_cfg.nsectors; -+ nfi_write32(snf, SNF_MISC_CTL2, -+ (wr_bytes << PROGRAM_LOAD_BYTE_NUM_S) | wr_bytes); -+ -+ // NFI write prepare -+ nfi_write16(snf, NFI_CNFG, -+ (CNFG_OP_MODE_PROGRAM << CNFG_OP_MODE_S) | -+ CNFG_DMA_BURST_EN | CNFG_DMA_MODE | op_mode); -+ -+ nfi_write32(snf, NFI_CON, (snf->nfi_cfg.nsectors << CON_SEC_NUM_S)); -+ buf_dma = dma_map_single(snf->dev, snf->buf, dma_len, DMA_TO_DEVICE); -+ if (dma_mapping_error(snf->dev, buf_dma)) { -+ dev_err(snf->dev, "DMA mapping failed.\n"); -+ goto cleanup; -+ } -+ nfi_write32(snf, NFI_STRADDR, buf_dma); -+ if (op->data.ecc) { -+ snf->ecc_cfg->op = ECC_ENCODE; -+ ret = mtk_ecc_enable(snf->ecc, snf->ecc_cfg); -+ if (ret) -+ goto cleanup_dma; -+ } -+ // Prepare for custom write interrupt -+ nfi_write32(snf, NFI_INTR_EN, NFI_IRQ_INTR_EN | NFI_IRQ_CUS_PG); -+ reinit_completion(&snf->op_done); -+ ; -+ -+ // Trigger NFI into custom mode -+ nfi_write16(snf, NFI_CMD, NFI_CMD_DUMMY_WRITE); -+ -+ // Start DMA write -+ nfi_rmw32(snf, NFI_CON, 0, CON_BWR); -+ nfi_write16(snf, NFI_STRDATA, STR_DATA); -+ -+ if (!wait_for_completion_timeout( -+ &snf->op_done, usecs_to_jiffies(SNFI_POLL_INTERVAL))) { -+ dev_err(snf->dev, "DMA timed out for program load.\n"); -+ ret = -ETIMEDOUT; -+ goto cleanup_ecc; -+ } -+ -+ // Wait for NFI_SEC_CNTR returning expected value -+ ret = readl_poll_timeout(snf->nfi_base + NFI_ADDRCNTR, val, -+ NFI_SEC_CNTR(val) >= snf->nfi_cfg.nsectors, 0, -+ SNFI_POLL_INTERVAL); -+ if (ret) -+ dev_err(snf->dev, "Timed out waiting for NFI_SEC_CNTR\n"); -+ -+cleanup_ecc: -+ if (op->data.ecc) -+ mtk_ecc_disable(snf->ecc); -+cleanup_dma: -+ dma_unmap_single(snf->dev, buf_dma, dma_len, DMA_TO_DEVICE); -+cleanup: -+ // Stop write -+ nfi_write32(snf, NFI_CON, 0); -+ nfi_write16(snf, NFI_CNFG, 0); -+ -+ // Clear SNF done flag -+ nfi_rmw32(snf, SNF_STA_CTL1, 0, CUS_PG_DONE); -+ nfi_write32(snf, SNF_STA_CTL1, 0); -+ -+ // Disable interrupt -+ nfi_read32(snf, NFI_INTR_STA); -+ nfi_write32(snf, NFI_INTR_EN, 0); -+ -+ nfi_rmw32(snf, SNF_MISC_CTL, PG_LOAD_CUSTOM_EN, 0); -+ -+ return ret; -+} -+ -+/** -+ * mtk_snand_is_page_ops() - check if the op is a controller supported page op. -+ * @op spi-mem op to check -+ * -+ * Check whether op can be executed with read_from_cache or program_load -+ * mode in the controller. -+ * This controller can execute typical Read From Cache and Program Load -+ * instructions found on SPI-NAND with 2-byte address. -+ * DTR and cmd buswidth & nbytes should be checked before calling this. -+ * -+ * Return: true if the op matches the instruction template -+ */ -+static bool mtk_snand_is_page_ops(const struct spi_mem_op *op) -+{ -+ if (op->addr.nbytes != 2) -+ return false; -+ -+ if (op->addr.buswidth != 1 && op->addr.buswidth != 2 && -+ op->addr.buswidth != 4) -+ return false; -+ -+ // match read from page instructions -+ if (op->data.dir == SPI_MEM_DATA_IN) { -+ // check dummy cycle first -+ if (op->dummy.nbytes * BITS_PER_BYTE / op->dummy.buswidth > -+ DATA_READ_MAX_DUMMY) -+ return false; -+ // quad io / quad out -+ if ((op->addr.buswidth == 4 || op->addr.buswidth == 1) && -+ op->data.buswidth == 4) -+ return true; -+ -+ // dual io / dual out -+ if ((op->addr.buswidth == 2 || op->addr.buswidth == 1) && -+ op->data.buswidth == 2) -+ return true; -+ -+ // standard spi -+ if (op->addr.buswidth == 1 && op->data.buswidth == 1) -+ return true; -+ } else if (op->data.dir == SPI_MEM_DATA_OUT) { -+ // check dummy cycle first -+ if (op->dummy.nbytes) -+ return false; -+ // program load quad out -+ if (op->addr.buswidth == 1 && op->data.buswidth == 4) -+ return true; -+ // standard spi -+ if (op->addr.buswidth == 1 && op->data.buswidth == 1) -+ return true; -+ } -+ return false; -+} -+ -+static bool mtk_snand_supports_op(struct spi_mem *mem, -+ const struct spi_mem_op *op) -+{ -+ if (!spi_mem_default_supports_op(mem, op)) -+ return false; -+ if (op->cmd.nbytes != 1 || op->cmd.buswidth != 1) -+ return false; -+ if (mtk_snand_is_page_ops(op)) -+ return true; -+ return ((op->addr.nbytes == 0 || op->addr.buswidth == 1) && -+ (op->dummy.nbytes == 0 || op->dummy.buswidth == 1) && -+ (op->data.nbytes == 0 || op->data.buswidth == 1)); -+} -+ -+static int mtk_snand_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op) -+{ -+ struct mtk_snand *ms = spi_controller_get_devdata(mem->spi->master); -+ // page ops transfer size must be exactly ((sector_size + spare_size) * -+ // nsectors). Limit the op size if the caller requests more than that. -+ // exec_op will read more than needed and discard the leftover if the -+ // caller requests less data. -+ if (mtk_snand_is_page_ops(op)) { -+ size_t l; -+ // skip adjust_op_size for page ops -+ if (ms->autofmt) -+ return 0; -+ l = ms->caps->sector_size + ms->nfi_cfg.spare_size; -+ l *= ms->nfi_cfg.nsectors; -+ if (op->data.nbytes > l) -+ op->data.nbytes = l; -+ } else { -+ size_t hl = op->cmd.nbytes + op->addr.nbytes + op->dummy.nbytes; -+ -+ if (hl >= SNF_GPRAM_SIZE) -+ return -EOPNOTSUPP; -+ if (op->data.nbytes > SNF_GPRAM_SIZE - hl) -+ op->data.nbytes = SNF_GPRAM_SIZE - hl; -+ } -+ return 0; -+} -+ -+static int mtk_snand_exec_op(struct spi_mem *mem, const struct spi_mem_op *op) -+{ -+ struct mtk_snand *ms = spi_controller_get_devdata(mem->spi->master); -+ -+ dev_dbg(ms->dev, "OP %02x ADDR %08llX@%d:%u DATA %d:%u", op->cmd.opcode, -+ op->addr.val, op->addr.buswidth, op->addr.nbytes, -+ op->data.buswidth, op->data.nbytes); -+ if (mtk_snand_is_page_ops(op)) { -+ if (op->data.dir == SPI_MEM_DATA_IN) -+ return mtk_snand_read_page_cache(ms, op); -+ else -+ return mtk_snand_write_page_cache(ms, op); -+ } else { -+ return mtk_snand_mac_io(ms, op); -+ } -+} -+ -+static const struct spi_controller_mem_ops mtk_snand_mem_ops = { -+ .adjust_op_size = mtk_snand_adjust_op_size, -+ .supports_op = mtk_snand_supports_op, -+ .exec_op = mtk_snand_exec_op, -+}; -+ -+static const struct spi_controller_mem_caps mtk_snand_mem_caps = { -+ .ecc = true, -+}; -+ -+static irqreturn_t mtk_snand_irq(int irq, void *id) -+{ -+ struct mtk_snand *snf = id; -+ u32 sta, ien; -+ -+ sta = nfi_read32(snf, NFI_INTR_STA); -+ ien = nfi_read32(snf, NFI_INTR_EN); -+ -+ if (!(sta & ien)) -+ return IRQ_NONE; -+ -+ nfi_write32(snf, NFI_INTR_EN, 0); -+ complete(&snf->op_done); -+ return IRQ_HANDLED; -+} -+ -+static const struct of_device_id mtk_snand_ids[] = { -+ { .compatible = "mediatek,mt7622-snand", .data = &mt7622_snand_caps }, -+ { .compatible = "mediatek,mt7629-snand", .data = &mt7629_snand_caps }, -+ {}, -+}; -+ -+MODULE_DEVICE_TABLE(of, mtk_snand_ids); -+ -+static int mtk_snand_enable_clk(struct mtk_snand *ms) -+{ -+ int ret; -+ -+ ret = clk_prepare_enable(ms->nfi_clk); -+ if (ret) { -+ dev_err(ms->dev, "unable to enable nfi clk\n"); -+ return ret; -+ } -+ ret = clk_prepare_enable(ms->pad_clk); -+ if (ret) { -+ dev_err(ms->dev, "unable to enable pad clk\n"); -+ goto err1; -+ } -+ return 0; -+err1: -+ clk_disable_unprepare(ms->nfi_clk); -+ return ret; -+} -+ -+static void mtk_snand_disable_clk(struct mtk_snand *ms) -+{ -+ clk_disable_unprepare(ms->pad_clk); -+ clk_disable_unprepare(ms->nfi_clk); -+} -+ -+static int mtk_snand_probe(struct platform_device *pdev) -+{ -+ struct device_node *np = pdev->dev.of_node; -+ const struct of_device_id *dev_id; -+ struct spi_controller *ctlr; -+ struct mtk_snand *ms; -+ int ret; -+ -+ dev_id = of_match_node(mtk_snand_ids, np); -+ if (!dev_id) -+ return -EINVAL; -+ -+ ctlr = devm_spi_alloc_master(&pdev->dev, sizeof(*ms)); -+ if (!ctlr) -+ return -ENOMEM; -+ platform_set_drvdata(pdev, ctlr); -+ -+ ms = spi_controller_get_devdata(ctlr); -+ -+ ms->ctlr = ctlr; -+ ms->caps = dev_id->data; -+ -+ ms->ecc = of_mtk_ecc_get(np); -+ if (IS_ERR(ms->ecc)) -+ return PTR_ERR(ms->ecc); -+ else if (!ms->ecc) -+ return -ENODEV; -+ -+ ms->nfi_base = devm_platform_ioremap_resource(pdev, 0); -+ if (IS_ERR(ms->nfi_base)) { -+ ret = PTR_ERR(ms->nfi_base); -+ goto release_ecc; -+ } -+ -+ ms->dev = &pdev->dev; -+ -+ ms->nfi_clk = devm_clk_get(&pdev->dev, "nfi_clk"); -+ if (IS_ERR(ms->nfi_clk)) { -+ ret = PTR_ERR(ms->nfi_clk); -+ dev_err(&pdev->dev, "unable to get nfi_clk, err = %d\n", ret); -+ goto release_ecc; -+ } -+ -+ ms->pad_clk = devm_clk_get(&pdev->dev, "pad_clk"); -+ if (IS_ERR(ms->pad_clk)) { -+ ret = PTR_ERR(ms->pad_clk); -+ dev_err(&pdev->dev, "unable to get pad_clk, err = %d\n", ret); -+ goto release_ecc; -+ } -+ -+ ret = mtk_snand_enable_clk(ms); -+ if (ret) -+ goto release_ecc; -+ -+ init_completion(&ms->op_done); -+ -+ ms->irq = platform_get_irq(pdev, 0); -+ if (ms->irq < 0) { -+ ret = ms->irq; -+ goto disable_clk; -+ } -+ ret = devm_request_irq(ms->dev, ms->irq, mtk_snand_irq, 0x0, -+ "mtk-snand", ms); -+ if (ret) { -+ dev_err(ms->dev, "failed to request snfi irq\n"); -+ goto disable_clk; -+ } -+ -+ ret = dma_set_mask(ms->dev, DMA_BIT_MASK(32)); -+ if (ret) { -+ dev_err(ms->dev, "failed to set dma mask\n"); -+ goto disable_clk; -+ } -+ -+ // switch to SNFI mode -+ nfi_write32(ms, SNF_CFG, SPI_MODE); -+ -+ // setup an initial page format for ops matching page_cache_op template -+ // before ECC is called. -+ ret = mtk_snand_setup_pagefmt(ms, ms->caps->sector_size, -+ ms->caps->spare_sizes[0]); -+ if (ret) { -+ dev_err(ms->dev, "failed to set initial page format\n"); -+ goto disable_clk; -+ } -+ -+ // setup ECC engine -+ ms->ecc_eng.dev = &pdev->dev; -+ ms->ecc_eng.integration = NAND_ECC_ENGINE_INTEGRATION_PIPELINED; -+ ms->ecc_eng.ops = &mtk_snfi_ecc_engine_ops; -+ ms->ecc_eng.priv = ms; -+ -+ ret = nand_ecc_register_on_host_hw_engine(&ms->ecc_eng); -+ if (ret) { -+ dev_err(&pdev->dev, "failed to register ecc engine.\n"); -+ goto disable_clk; -+ } -+ -+ ctlr->num_chipselect = 1; -+ ctlr->mem_ops = &mtk_snand_mem_ops; -+ ctlr->mem_caps = &mtk_snand_mem_caps; -+ ctlr->bits_per_word_mask = SPI_BPW_MASK(8); -+ ctlr->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD | SPI_TX_DUAL | SPI_TX_QUAD; -+ ctlr->dev.of_node = pdev->dev.of_node; -+ ret = spi_register_controller(ctlr); -+ if (ret) { -+ dev_err(&pdev->dev, "spi_register_controller failed.\n"); -+ goto disable_clk; -+ } -+ -+ return 0; -+disable_clk: -+ mtk_snand_disable_clk(ms); -+release_ecc: -+ mtk_ecc_release(ms->ecc); -+ return ret; -+} -+ -+static int mtk_snand_remove(struct platform_device *pdev) -+{ -+ struct spi_controller *ctlr = platform_get_drvdata(pdev); -+ struct mtk_snand *ms = spi_controller_get_devdata(ctlr); -+ -+ spi_unregister_controller(ctlr); -+ mtk_snand_disable_clk(ms); -+ mtk_ecc_release(ms->ecc); -+ kfree(ms->buf); -+ return 0; -+} -+ -+static struct platform_driver mtk_snand_driver = { -+ .probe = mtk_snand_probe, -+ .remove = mtk_snand_remove, -+ .driver = { -+ .name = "mtk-snand", -+ .of_match_table = mtk_snand_ids, -+ }, -+}; -+ -+module_platform_driver(mtk_snand_driver); -+ -+MODULE_LICENSE("GPL"); -+MODULE_AUTHOR("Chuanhong Guo "); -+MODULE_DESCRIPTION("MeidaTek SPI-NAND Flash Controller Driver"); diff --git a/target/linux/mediatek/patches-5.15/120-13-v5.19-mtd-nand-mtk-ecc-also-parse-nand-ecc-engine-if-avail.patch b/target/linux/mediatek/patches-5.15/120-13-v5.19-mtd-nand-mtk-ecc-also-parse-nand-ecc-engine-if-avail.patch deleted file mode 100644 index 01d9d12088..0000000000 --- a/target/linux/mediatek/patches-5.15/120-13-v5.19-mtd-nand-mtk-ecc-also-parse-nand-ecc-engine-if-avail.patch +++ /dev/null @@ -1,30 +0,0 @@ -From 433b76fa0f3ca2865841abc21538dd8077ca3edd Mon Sep 17 00:00:00 2001 -From: Chuanhong Guo -Date: Mon, 4 Apr 2022 00:05:38 +0800 -Subject: [PATCH 13/15] mtd: nand: mtk-ecc: also parse nand-ecc-engine if - available - -The recently added ECC engine support introduced a generic property -named nand-ecc-engine for ecc engine phandle. This patch adds support -for this new property. - -Signed-off-by: Chuanhong Guo -(cherry picked from commit a41f25feb6e47c1c4d8d3279ae990ccbd8dfab54) ---- - drivers/mtd/nand/ecc-mtk.c | 5 ++++- - 1 file changed, 4 insertions(+), 1 deletion(-) - ---- a/drivers/mtd/nand/ecc-mtk.c -+++ b/drivers/mtd/nand/ecc-mtk.c -@@ -279,7 +279,10 @@ struct mtk_ecc *of_mtk_ecc_get(struct de - struct mtk_ecc *ecc = NULL; - struct device_node *np; - -- np = of_parse_phandle(of_node, "ecc-engine", 0); -+ np = of_parse_phandle(of_node, "nand-ecc-engine", 0); -+ /* for backward compatibility */ -+ if (!np) -+ np = of_parse_phandle(of_node, "ecc-engine", 0); - if (np) { - ecc = mtk_ecc_get(np); - of_node_put(np); diff --git a/target/linux/mediatek/patches-5.15/120-14-v5.19-arm64-dts-mediatek-add-mtk-snfi-for-mt7622.patch b/target/linux/mediatek/patches-5.15/120-14-v5.19-arm64-dts-mediatek-add-mtk-snfi-for-mt7622.patch deleted file mode 100644 index 15d2671372..0000000000 --- a/target/linux/mediatek/patches-5.15/120-14-v5.19-arm64-dts-mediatek-add-mtk-snfi-for-mt7622.patch +++ /dev/null @@ -1,35 +0,0 @@ -From 9ba7c246063ae43baf2e53ccc8c8b5f8d025aaaa Mon Sep 17 00:00:00 2001 -From: Chuanhong Guo -Date: Sun, 3 Apr 2022 10:19:29 +0800 -Subject: [PATCH 15/15] arm64: dts: mediatek: add mtk-snfi for mt7622 - -This patch adds a device-tree node for the MTK SPI-NAND Flash Interface -for MT7622 device tree. - -Signed-off-by: Chuanhong Guo -(cherry picked from commit 2e022641709011ef0843d0416b0f264b5fc217af) ---- - arch/arm64/boot/dts/mediatek/mt7622.dtsi | 12 ++++++++++++ - 1 file changed, 12 insertions(+) - ---- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi -@@ -553,6 +553,18 @@ - status = "disabled"; - }; - -+ snfi: spi@1100d000 { -+ compatible = "mediatek,mt7622-snand"; -+ reg = <0 0x1100d000 0 0x1000>; -+ interrupts = ; -+ clocks = <&pericfg CLK_PERI_NFI_PD>, <&pericfg CLK_PERI_SNFI_PD>; -+ clock-names = "nfi_clk", "pad_clk"; -+ nand-ecc-engine = <&bch>; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ status = "disabled"; -+ }; -+ - bch: ecc@1100e000 { - compatible = "mediatek,mt7622-ecc"; - reg = <0 0x1100e000 0 0x1000>; diff --git a/target/linux/mediatek/patches-5.15/121-hack-spi-nand-1b-bbm.patch b/target/linux/mediatek/patches-5.15/121-hack-spi-nand-1b-bbm.patch deleted file mode 100644 index ff5521c44e..0000000000 --- a/target/linux/mediatek/patches-5.15/121-hack-spi-nand-1b-bbm.patch +++ /dev/null @@ -1,20 +0,0 @@ ---- a/drivers/mtd/nand/spi/core.c -+++ b/drivers/mtd/nand/spi/core.c -@@ -724,7 +724,7 @@ static int spinand_mtd_write(struct mtd_ - static bool spinand_isbad(struct nand_device *nand, const struct nand_pos *pos) - { - struct spinand_device *spinand = nand_to_spinand(nand); -- u8 marker[2] = { }; -+ u8 marker[1] = { }; - struct nand_page_io_req req = { - .pos = *pos, - .ooblen = sizeof(marker), -@@ -735,7 +735,7 @@ static bool spinand_isbad(struct nand_de - - spinand_select_target(spinand, pos->target); - spinand_read_page(spinand, &req); -- if (marker[0] != 0xff || marker[1] != 0xff) -+ if (marker[0] != 0xff) - return true; - - return false; diff --git a/target/linux/mediatek/patches-5.15/130-dts-mt7629-add-snand-support.patch b/target/linux/mediatek/patches-5.15/130-dts-mt7629-add-snand-support.patch deleted file mode 100644 index be0018a383..0000000000 --- a/target/linux/mediatek/patches-5.15/130-dts-mt7629-add-snand-support.patch +++ /dev/null @@ -1,94 +0,0 @@ -From c813fbe806257c574240770ef716fbee19f7dbfa Mon Sep 17 00:00:00 2001 -From: Xiangsheng Hou -Date: Thu, 6 Jun 2019 16:29:04 +0800 -Subject: [PATCH] spi: spi-mem: Mediatek: Add SPI Nand support for MT7629 - -Signed-off-by: Xiangsheng Hou ---- - arch/arm/boot/dts/mt7629-rfb.dts | 45 ++++++++++++++++++++++++++++++++ - arch/arm/boot/dts/mt7629.dtsi | 22 ++++++++++++++++ - 3 files changed, 79 insertions(+) - ---- a/arch/arm/boot/dts/mt7629.dtsi -+++ b/arch/arm/boot/dts/mt7629.dtsi -@@ -272,6 +272,27 @@ - status = "disabled"; - }; - -+ snfi: spi@1100d000 { -+ compatible = "mediatek,mt7629-snand"; -+ reg = <0x1100d000 0x1000>; -+ interrupts = ; -+ clocks = <&pericfg CLK_PERI_NFI_PD>, <&pericfg CLK_PERI_SNFI_PD>; -+ clock-names = "nfi_clk", "pad_clk"; -+ nand-ecc-engine = <&bch>; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ status = "disabled"; -+ }; -+ -+ bch: ecc@1100e000 { -+ compatible = "mediatek,mt7622-ecc"; -+ reg = <0x1100e000 0x1000>; -+ interrupts = ; -+ clocks = <&pericfg CLK_PERI_NFIECC_PD>; -+ clock-names = "nfiecc_clk"; -+ status = "disabled"; -+ }; -+ - spi: spi@1100a000 { - compatible = "mediatek,mt7629-spi", - "mediatek,mt7622-spi"; ---- a/arch/arm/boot/dts/mt7629-rfb.dts -+++ b/arch/arm/boot/dts/mt7629-rfb.dts -@@ -254,6 +254,50 @@ - }; - }; - -+&bch { -+ status = "okay"; -+}; -+ -+&snfi { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&serial_nand_pins>; -+ status = "okay"; -+ flash@0 { -+ compatible = "spi-nand"; -+ reg = <0>; -+ spi-tx-bus-width = <4>; -+ spi-rx-bus-width = <4>; -+ nand-ecc-engine = <&snfi>; -+ -+ partitions { -+ compatible = "fixed-partitions"; -+ #address-cells = <1>; -+ #size-cells = <1>; -+ -+ partition@0 { -+ label = "Bootloader"; -+ reg = <0x00000 0x0100000>; -+ read-only; -+ }; -+ -+ partition@100000 { -+ label = "Config"; -+ reg = <0x100000 0x0040000>; -+ }; -+ -+ partition@140000 { -+ label = "factory"; -+ reg = <0x140000 0x0080000>; -+ }; -+ -+ partition@1c0000 { -+ label = "firmware"; -+ reg = <0x1c0000 0x1000000>; -+ }; -+ }; -+ }; -+}; -+ - &spi { - pinctrl-names = "default"; - pinctrl-0 = <&spi_pins>; diff --git a/target/linux/mediatek/patches-5.15/131-dts-mt7622-add-snand-support.patch b/target/linux/mediatek/patches-5.15/131-dts-mt7622-add-snand-support.patch deleted file mode 100644 index 134e5997e2..0000000000 --- a/target/linux/mediatek/patches-5.15/131-dts-mt7622-add-snand-support.patch +++ /dev/null @@ -1,68 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts -+++ b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts -@@ -539,6 +539,65 @@ - status = "disabled"; - }; - -+&bch { -+ status = "okay"; -+}; -+ -+&snfi { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&serial_nand_pins>; -+ status = "okay"; -+ flash@0 { -+ compatible = "spi-nand"; -+ reg = <0>; -+ spi-tx-bus-width = <4>; -+ spi-rx-bus-width = <4>; -+ nand-ecc-engine = <&snfi>; -+ -+ partitions { -+ compatible = "fixed-partitions"; -+ #address-cells = <1>; -+ #size-cells = <1>; -+ -+ partition@0 { -+ label = "Preloader"; -+ reg = <0x00000 0x0080000>; -+ read-only; -+ }; -+ -+ partition@80000 { -+ label = "ATF"; -+ reg = <0x80000 0x0040000>; -+ }; -+ -+ partition@c0000 { -+ label = "Bootloader"; -+ reg = <0xc0000 0x0080000>; -+ }; -+ -+ partition@140000 { -+ label = "Config"; -+ reg = <0x140000 0x0080000>; -+ }; -+ -+ partition@1c0000 { -+ label = "Factory"; -+ reg = <0x1c0000 0x0100000>; -+ }; -+ -+ partition@200000 { -+ label = "firmware"; -+ reg = <0x2c0000 0x2000000>; -+ }; -+ -+ partition@2200000 { -+ label = "User_data"; -+ reg = <0x22c0000 0x4000000>; -+ }; -+ }; -+ }; -+}; -+ - &spi0 { - pinctrl-names = "default"; - pinctrl-0 = <&spic0_pins>; diff --git a/target/linux/mediatek/patches-5.15/140-dts-fix-wmac-support-for-mt7622-rfb1.patch b/target/linux/mediatek/patches-5.15/140-dts-fix-wmac-support-for-mt7622-rfb1.patch deleted file mode 100644 index 8e6935b434..0000000000 --- a/target/linux/mediatek/patches-5.15/140-dts-fix-wmac-support-for-mt7622-rfb1.patch +++ /dev/null @@ -1,18 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts -+++ b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts -@@ -580,7 +580,7 @@ - reg = <0x140000 0x0080000>; - }; - -- partition@1c0000 { -+ factory: partition@1c0000 { - label = "Factory"; - reg = <0x1c0000 0x0100000>; - }; -@@ -641,5 +641,6 @@ - &wmac { - pinctrl-names = "default"; - pinctrl-0 = <&wmac_pins>; -+ mediatek,mtd-eeprom = <&factory 0x0000>; - status = "okay"; - }; diff --git a/target/linux/mediatek/patches-5.15/150-dts-mt7623-eip97-inside-secure-support.patch b/target/linux/mediatek/patches-5.15/150-dts-mt7623-eip97-inside-secure-support.patch deleted file mode 100644 index 5b63bf4226..0000000000 --- a/target/linux/mediatek/patches-5.15/150-dts-mt7623-eip97-inside-secure-support.patch +++ /dev/null @@ -1,24 +0,0 @@ ---- a/arch/arm/boot/dts/mt7623.dtsi -+++ b/arch/arm/boot/dts/mt7623.dtsi -@@ -951,17 +951,15 @@ - }; - - crypto: crypto@1b240000 { -- compatible = "mediatek,eip97-crypto"; -+ compatible = "inside-secure,safexcel-eip97"; - reg = <0 0x1b240000 0 0x20000>; - interrupts = , - , - , -- , -- ; -+ ; -+ interrupt-names = "ring0", "ring1", "ring2", "ring3"; - clocks = <ðsys CLK_ETHSYS_CRYPTO>; -- clock-names = "cryp"; -- power-domains = <&scpsys MT2701_POWER_DOMAIN_ETH>; -- status = "disabled"; -+ status = "okay"; - }; - - bdpsys: syscon@1c000000 { diff --git a/target/linux/mediatek/patches-5.15/160-dts-mt7623-bpi-r2-earlycon.patch b/target/linux/mediatek/patches-5.15/160-dts-mt7623-bpi-r2-earlycon.patch deleted file mode 100644 index 091cffc3c0..0000000000 --- a/target/linux/mediatek/patches-5.15/160-dts-mt7623-bpi-r2-earlycon.patch +++ /dev/null @@ -1,11 +0,0 @@ ---- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts -+++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts -@@ -19,7 +19,7 @@ - - chosen { - stdout-path = "serial2:115200n8"; -- bootargs = "console=ttyS2,115200n8 console=tty1"; -+ bootargs = "earlycon=uart8250,mmio32,0x11004000 console=ttyS2,115200n8 console=tty1"; - }; - - connector { diff --git a/target/linux/mediatek/patches-5.15/161-dts-mt7623-bpi-r2-mmc-device-order.patch b/target/linux/mediatek/patches-5.15/161-dts-mt7623-bpi-r2-mmc-device-order.patch deleted file mode 100644 index d1bafc1526..0000000000 --- a/target/linux/mediatek/patches-5.15/161-dts-mt7623-bpi-r2-mmc-device-order.patch +++ /dev/null @@ -1,11 +0,0 @@ ---- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts -+++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts -@@ -15,6 +15,8 @@ - - aliases { - serial2 = &uart2; -+ mmc0 = &mmc0; -+ mmc1 = &mmc1; - }; - - chosen { diff --git a/target/linux/mediatek/patches-5.15/162-dts-mt7623-bpi-r2-led-aliases.patch b/target/linux/mediatek/patches-5.15/162-dts-mt7623-bpi-r2-led-aliases.patch deleted file mode 100644 index f6745add5b..0000000000 --- a/target/linux/mediatek/patches-5.15/162-dts-mt7623-bpi-r2-led-aliases.patch +++ /dev/null @@ -1,29 +0,0 @@ ---- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts -+++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts -@@ -17,6 +17,10 @@ - serial2 = &uart2; - mmc0 = &mmc0; - mmc1 = &mmc1; -+ led-boot = &led_system_green; -+ led-failsafe = &led_system_blue; -+ led-running = &led_system_green; -+ led-upgrade = &led_system_blue; - }; - - chosen { -@@ -112,13 +116,13 @@ - pinctrl-names = "default"; - pinctrl-0 = <&led_pins_a>; - -- blue { -+ led_system_blue: blue { - label = "bpi-r2:pio:blue"; - gpios = <&pio 240 GPIO_ACTIVE_LOW>; - default-state = "off"; - }; - -- green { -+ led_system_green: green { - label = "bpi-r2:pio:green"; - gpios = <&pio 241 GPIO_ACTIVE_LOW>; - default-state = "off"; diff --git a/target/linux/mediatek/patches-5.15/163-dts-mt7623-bpi-r2-ethernet-alias.patch b/target/linux/mediatek/patches-5.15/163-dts-mt7623-bpi-r2-ethernet-alias.patch deleted file mode 100644 index b1dd75a414..0000000000 --- a/target/linux/mediatek/patches-5.15/163-dts-mt7623-bpi-r2-ethernet-alias.patch +++ /dev/null @@ -1,10 +0,0 @@ ---- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts -+++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts -@@ -15,6 +15,7 @@ - - aliases { - serial2 = &uart2; -+ ethernet0 = &gmac0; - mmc0 = &mmc0; - mmc1 = &mmc1; - led-boot = &led_system_green; diff --git a/target/linux/mediatek/patches-5.15/173-arm-dts-mt7623-add-musb-device-nodes.patch b/target/linux/mediatek/patches-5.15/173-arm-dts-mt7623-add-musb-device-nodes.patch deleted file mode 100644 index ba1d1fe202..0000000000 --- a/target/linux/mediatek/patches-5.15/173-arm-dts-mt7623-add-musb-device-nodes.patch +++ /dev/null @@ -1,69 +0,0 @@ -From 21d106f15262f5a2ef7531636e0703ee61c33c61 Mon Sep 17 00:00:00 2001 -From: Sungbo Eo -Date: Sun, 8 Aug 2021 21:38:40 +0900 -Subject: [PATCH 2/2] arm: dts: mt7623: add musb device nodes - -MT7623 has an musb controller that is compatible with the one from MT2701. - -Signed-off-by: Sungbo Eo ---- - arch/arm/boot/dts/mt7623.dtsi | 34 ++++++++++++++++++++++++++++++++++ - arch/arm/boot/dts/mt7623a.dtsi | 4 ++++ - 2 files changed, 38 insertions(+) - ---- a/arch/arm/boot/dts/mt7623.dtsi -+++ b/arch/arm/boot/dts/mt7623.dtsi -@@ -585,6 +585,40 @@ - status = "disabled"; - }; - -+ usb0: usb@11200000 { -+ compatible = "mediatek,mt7623-musb", -+ "mediatek,mtk-musb"; -+ reg = <0 0x11200000 0 0x1000>; -+ interrupts = ; -+ interrupt-names = "mc"; -+ phys = <&u2port2 PHY_TYPE_USB2>; -+ dr_mode = "otg"; -+ clocks = <&pericfg CLK_PERI_USB0>, -+ <&pericfg CLK_PERI_USB0_MCU>, -+ <&pericfg CLK_PERI_USB_SLV>; -+ clock-names = "main","mcu","univpll"; -+ power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>; -+ status = "disabled"; -+ }; -+ -+ u2phy1: t-phy@11210000 { -+ compatible = "mediatek,mt7623-tphy", -+ "mediatek,generic-tphy-v1"; -+ reg = <0 0x11210000 0 0x0800>; -+ #address-cells = <2>; -+ #size-cells = <2>; -+ ranges; -+ status = "disabled"; -+ -+ u2port2: usb-phy@11210800 { -+ reg = <0 0x11210800 0 0x0100>; -+ clocks = <&topckgen CLK_TOP_USB_PHY48M>; -+ clock-names = "ref"; -+ #phy-cells = <1>; -+ status = "okay"; -+ }; -+ }; -+ - audsys: clock-controller@11220000 { - compatible = "mediatek,mt7623-audsys", - "mediatek,mt2701-audsys", ---- a/arch/arm/boot/dts/mt7623a.dtsi -+++ b/arch/arm/boot/dts/mt7623a.dtsi -@@ -35,6 +35,10 @@ - clock-names = "ethif"; - }; - -+&usb0 { -+ power-domains = <&scpsys MT7623A_POWER_DOMAIN_IFR_MSC>; -+}; -+ - &usb1 { - power-domains = <&scpsys MT7623A_POWER_DOMAIN_HIF>; - }; diff --git a/target/linux/mediatek/patches-5.15/180-dts-mt7622-bpi-r64-add-mt7531-irq.patch b/target/linux/mediatek/patches-5.15/180-dts-mt7622-bpi-r64-add-mt7531-irq.patch deleted file mode 100644 index 80ceb490d4..0000000000 --- a/target/linux/mediatek/patches-5.15/180-dts-mt7622-bpi-r64-add-mt7531-irq.patch +++ /dev/null @@ -1,13 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -@@ -160,6 +160,10 @@ - switch@0 { - compatible = "mediatek,mt7531"; - reg = <0>; -+ interrupt-controller; -+ #interrupt-cells = <1>; -+ interrupt-parent = <&pio>; -+ interrupts = <53 IRQ_TYPE_LEVEL_HIGH>; - reset-gpios = <&pio 54 0>; - - ports { diff --git a/target/linux/mediatek/patches-5.15/190-arm64-dts-mediatek-mt7622-fix-GICv2-range.patch b/target/linux/mediatek/patches-5.15/190-arm64-dts-mediatek-mt7622-fix-GICv2-range.patch deleted file mode 100644 index 39a9770d98..0000000000 --- a/target/linux/mediatek/patches-5.15/190-arm64-dts-mediatek-mt7622-fix-GICv2-range.patch +++ /dev/null @@ -1,106 +0,0 @@ -From patchwork Tue Apr 26 19:51:36 2022 -Content-Type: text/plain; charset="utf-8" -MIME-Version: 1.0 -Content-Transfer-Encoding: 7bit -X-Patchwork-Submitter: Daniel Golle -X-Patchwork-Id: 12827872 -Return-Path: - -X-Spam-Checker-Version: SpamAssassin 3.4.0 (2014-02-07) on - aws-us-west-2-korg-lkml-1.web.codeaurora.org -Received: from bombadil.infradead.org (bombadil.infradead.org - [198.137.202.133]) - (using TLSv1.2 with cipher ECDHE-RSA-AES256-GCM-SHA384 (256/256 bits)) - (No client certificate requested) - by smtp.lore.kernel.org (Postfix) with ESMTPS id BACF3C433EF - for ; - Tue, 26 Apr 2022 19:53:05 +0000 (UTC) -DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; - d=lists.infradead.org; s=bombadil.20210309; h=Sender: - Content-Transfer-Encoding:Content-Type:List-Subscribe:List-Help:List-Post: - List-Archive:List-Unsubscribe:List-Id:MIME-Version:Message-ID:Subject:Cc:To: - From:Date:Reply-To:Content-ID:Content-Description:Resent-Date:Resent-From: - Resent-Sender:Resent-To:Resent-Cc:Resent-Message-ID:In-Reply-To:References: - List-Owner; bh=OWGSxvlKoyPWz6b629RNINucULo6oOdFssAIiJETWRg=; b=T0HEjee0FX3hlb - x5jl7xLK5sKM0pkE2oRgwzthbFlNg8ST1j/2GkgcgT0S2Bi0vRfFxHeu/RKzS9RmiVnKJnPGL8ctg - WoBLyO5i+NcmosGoy6MmoOjGTNhj/+3q3Z1jRLBSJ4ySSP22X77YeuJTmVzySPUllQhWvDhjMVCR9 - QBRmQdc6gCAg3IYGEbWwS2TG+UHveDCeZRWxMzrwI8UPadNCRFROwugmiQ3mdU41lHCTDpnlfuRJh - o1igLKfMBLz+D8rFYvDh7FfkcKkY6lNoswA2HKUun1MEzgoyQKmITPnG2maX/BvJJuj/B3ZJShh4k - AZHmXoQxq1mrsm2FxfnQ==; -Received: from localhost ([::1] helo=bombadil.infradead.org) - by bombadil.infradead.org with esmtp (Exim 4.94.2 #2 (Red Hat Linux)) - id 1njRE5-00G05D-9z; Tue, 26 Apr 2022 19:51:57 +0000 -Received: from fudo.makrotopia.org ([2a07:2ec0:3002::71]) - by bombadil.infradead.org with esmtps (Exim 4.94.2 #2 (Red Hat Linux)) - id 1njRE1-00G03h-9H; Tue, 26 Apr 2022 19:51:55 +0000 -Received: from local - by fudo.makrotopia.org with esmtpsa (TLS1.3:TLS_AES_256_GCM_SHA384:256) - (Exim 4.94.2) (envelope-from ) - id 1njRDu-0006aF-4F; Tue, 26 Apr 2022 21:51:46 +0200 -Date: Tue, 26 Apr 2022 20:51:36 +0100 -From: Daniel Golle -To: devicetree@vger.kernel.org, linux-mediatek@lists.infradead.org, - linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org -Cc: Rob Herring , - Krzysztof Kozlowski , - Matthias Brugger -Subject: [PATCH] arm64: dts: mediatek: mt7622: fix GICv2 range -Message-ID: -MIME-Version: 1.0 -Content-Disposition: inline -X-CRM114-Version: 20100106-BlameMichelson ( TRE 0.8.0 (BSD) ) MR-646709E3 -X-CRM114-CacheID: sfid-20220426_125153_359242_EA3D452C -X-CRM114-Status: GOOD ( 12.45 ) -X-BeenThere: linux-arm-kernel@lists.infradead.org -X-Mailman-Version: 2.1.34 -Precedence: list -List-Id: -List-Unsubscribe: - , - -List-Archive: -List-Post: -List-Help: -List-Subscribe: - , - -Sender: "linux-arm-kernel" -Errors-To: - linux-arm-kernel-bounces+linux-arm-kernel=archiver.kernel.org@lists.infradead.org - -With the current range specified for the CPU interface there is an -error message at boot: - -GIC: GICv2 detected, but range too small and irqchip.gicv2_force_probe not set - -Setting irqchip.gicv2_force_probe=1 in bootargs results in: - -GIC: Aliased GICv2 at 0x0000000010320000, trying to find the canonical range over 128kB -GIC: Adjusting CPU interface base to 0x000000001032f000 -GIC: Using split EOI/Deactivate mode - -Using the adjusted CPU interface base and 8K size results in only the -final line remaining and fully working system as well as /proc/interrupts -showing additional IPI3,4,5,6: - -IPI3: 0 0 CPU stop (for crash dump) interrupts -IPI4: 0 0 Timer broadcast interrupts -IPI5: 0 0 IRQ work interrupts -IPI6: 0 0 CPU wake-up interrupts - -Signed-off-by: Daniel Golle ---- - arch/arm64/boot/dts/mediatek/mt7622.dtsi | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi -@@ -339,7 +339,7 @@ - #interrupt-cells = <3>; - interrupt-parent = <&gic>; - reg = <0 0x10310000 0 0x1000>, -- <0 0x10320000 0 0x1000>, -+ <0 0x1032f000 0 0x2000>, - <0 0x10340000 0 0x2000>, - <0 0x10360000 0 0x2000>; - }; diff --git a/target/linux/mediatek/patches-5.15/191-v5.19-arm64-dts-mt7622-specify-the-L2-cache-topology.patch b/target/linux/mediatek/patches-5.15/191-v5.19-arm64-dts-mt7622-specify-the-L2-cache-topology.patch deleted file mode 100644 index 8851fefbb3..0000000000 --- a/target/linux/mediatek/patches-5.15/191-v5.19-arm64-dts-mt7622-specify-the-L2-cache-topology.patch +++ /dev/null @@ -1,132 +0,0 @@ -From patchwork Thu Apr 28 22:57:55 2022 -Content-Type: text/plain; charset="utf-8" -MIME-Version: 1.0 -Content-Transfer-Encoding: 7bit -X-Patchwork-Submitter: Rui Salvaterra -X-Patchwork-Id: 12831311 -Return-Path: - -X-Spam-Checker-Version: SpamAssassin 3.4.0 (2014-02-07) on - aws-us-west-2-korg-lkml-1.web.codeaurora.org -Received: from bombadil.infradead.org (bombadil.infradead.org - [198.137.202.133]) - (using TLSv1.2 with cipher ECDHE-RSA-AES256-GCM-SHA384 (256/256 bits)) - (No client certificate requested) - by smtp.lore.kernel.org (Postfix) with ESMTPS id 49367C433EF - for ; - Thu, 28 Apr 2022 22:59:15 +0000 (UTC) -DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; - d=lists.infradead.org; s=bombadil.20210309; h=Sender: - Content-Transfer-Encoding:Content-Type:List-Subscribe:List-Help:List-Post: - List-Archive:List-Unsubscribe:List-Id:MIME-Version:Message-Id:Date:Subject:Cc - :To:From:Reply-To:Content-ID:Content-Description:Resent-Date:Resent-From: - Resent-Sender:Resent-To:Resent-Cc:Resent-Message-ID:In-Reply-To:References: - List-Owner; bh=SerBW8MOw68wFFCbuq25LJzAcmqCfKMO2cFJxwFvZ+M=; b=nN4CYEO6VOGVbq - GSvQPGoya0L2IzQ/ZfknzQ853lY97zEPJk14ndK+TGQ+8ySjBSTu0xKgxlBoJj5G+DGubgRP1eZRJ - bktFqX2tohnrRavlceRxgVA3YFGBhjXE7AC0YzGC7auH2S6nSPUrH7cTVuaeIacIoV1AXPazc2hRU - u8RaJl1XHQwuhdZOsFBH99M5an3Zsmq0tsoIOYwB+gQaI307ZkqscxzcXFiCYCHlDvZlhHlW/WbdG - J+3iUnfq1KJWI2kE7TkPXMYaJzbEgG+LDrgYr3deADArCfCmnzbf0U29EZd6cR5D19GMVqGFDvsTX - H69W8qxVzJ+mR2HQd3GQ==; -Received: from localhost ([::1] helo=bombadil.infradead.org) - by bombadil.infradead.org with esmtp (Exim 4.94.2 #2 (Red Hat Linux)) - id 1nkD5T-008uVi-54; Thu, 28 Apr 2022 22:58:15 +0000 -Received: from mail-ed1-x533.google.com ([2a00:1450:4864:20::533]) - by bombadil.infradead.org with esmtps (Exim 4.94.2 #2 (Red Hat Linux)) - id 1nkD5P-008uUW-Px; Thu, 28 Apr 2022 22:58:13 +0000 -Received: by mail-ed1-x533.google.com with SMTP id p18so7146795edr.7; - Thu, 28 Apr 2022 15:58:08 -0700 (PDT) -DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20210112; - h=from:to:cc:subject:date:message-id:mime-version - :content-transfer-encoding; - bh=R5/7OCxhqk5o9giaTDUQztGpi5IgQbeepSeYSbhWdII=; - b=BZQqEcfqgYTQ01yTJ3p6tPu0vaoYxHxTZYXAPCQDyng2F9JErAwf+wBYyeCYL3jbyn - fu7P7HVw2JjagdSunf6J7t0o3nqtfHGPh/ZLJHzYdg1s5shotJ5wMbZpAHCMdC4+K+BV - uL4JNuQnZmCRBiUFM+rtrpfaTepwEclOBBGoL9iE+tm/pWzx/WIR5WB9W8CutqsrDxF5 - 8r5IwxNz3GLYfDgZMejyxQ0BjUIeQeCMTqhf73P19V3Bgg4MUbJ2q163D/OWSpHCbJdH - OfKEAdrVw4U7Rx0/SOnvPBxeiyCVH2uAkdPiFk+O3ZvsaiODty7uqGGjbN4chYEWRdp+ - 7WBQ== -X-Google-DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; - d=1e100.net; s=20210112; - h=x-gm-message-state:from:to:cc:subject:date:message-id:mime-version - :content-transfer-encoding; - bh=R5/7OCxhqk5o9giaTDUQztGpi5IgQbeepSeYSbhWdII=; - b=mvuzYrIKVAnpUgnlEa+S84XOruFt2VxxK25dib+Az/UPt4CzDO0h1u3SckfcmsFT4h - lUKka66CkdkHCJWC5JqKwSD0lbgtu2KWEsvtCWVDS+S6XKuAu99o2kvNyHC+/xW07dKL - zB7WAkyG53lrX0KH7fZ46uzHoRKWATW/idDhXBA49B+vaPqHKroSOn5JBKsu/hDwsQdf - zWA5tmOJweFjVZYe0ChD8OUDYOv+6RYlGqVvsQ5quMKJDBoC7KC8YMqvHc3K6DbQbnvZ - vJyXlcHgHSpadLRgg6wIY+ZyJyZsGqVyRD1TmcByRxSrUTGc3VSQeXUcUPv+3JFk9Esu - PqoA== -X-Gm-Message-State: AOAM530veLoWc1JsDUuaRxe8Wi4N5UaD7cH5c9nhGlW7j5aj9gwvCDya - /uqAd6FaNeLuB5hEWmAEXXugS+7njg== -X-Google-Smtp-Source: - ABdhPJyLbUuBj/1YYm+3qmglf7zy9b/YbbcMub3/HL40okdVxkr6/TVxIZulAoEV9PjbfrGkO2N3Bw== -X-Received: by 2002:a05:6402:2920:b0:425:d7c7:41f with SMTP id - ee32-20020a056402292000b00425d7c7041fmr29248373edb.370.1651186687432; - Thu, 28 Apr 2022 15:58:07 -0700 (PDT) -Received: from crystalwell.adg.lan (a109-49-0-175.cpe.netcabo.pt. - [109.49.0.175]) by smtp.gmail.com with ESMTPSA id - a25-20020a056402169900b0042617ba63c8sm2219102edv.82.2022.04.28.15.58.06 - (version=TLS1_3 cipher=TLS_AES_256_GCM_SHA384 bits=256/256); - Thu, 28 Apr 2022 15:58:06 -0700 (PDT) -From: Rui Salvaterra -To: linux-arm-kernel@lists.infradead.org, linux-mediatek@lists.infradead.org, - linux-kernel@vger.kernel.org -Cc: matthias.bgg@gmail.com, ryder.lee@mediatek.com, daniel@makrotopia.org, - Rui Salvaterra -Subject: [PATCH] arm64: dts: mt7622: specify the L2 cache topology -Date: Thu, 28 Apr 2022 23:57:55 +0100 -Message-Id: <20220428225755.785153-1-rsalvaterra@gmail.com> -X-Mailer: git-send-email 2.36.0 -MIME-Version: 1.0 -X-CRM114-Version: 20100106-BlameMichelson ( TRE 0.8.0 (BSD) ) MR-646709E3 -X-CRM114-CacheID: sfid-20220428_155811_895571_B63D2806 -X-CRM114-Status: GOOD ( 10.27 ) -X-BeenThere: linux-arm-kernel@lists.infradead.org -X-Mailman-Version: 2.1.34 -Precedence: list -List-Id: -List-Unsubscribe: - , - -List-Archive: -List-Post: -List-Help: -List-Subscribe: - , - -Sender: "linux-arm-kernel" -Errors-To: - linux-arm-kernel-bounces+linux-arm-kernel=archiver.kernel.org@lists.infradead.org - -On an MT7622 system, the kernel complains of not being able to detect the cache -hierarchy of CPU 0. Specify the shared L2 cache node in the device tree, in -order to fix this. - -Signed-off-by: Rui Salvaterra ---- - arch/arm64/boot/dts/mediatek/mt7622.dtsi | 7 +++++++ - 1 file changed, 7 insertions(+) - ---- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi -@@ -80,6 +80,7 @@ - enable-method = "psci"; - clock-frequency = <1300000000>; - cci-control-port = <&cci_control2>; -+ next-level-cache = <&L2>; - }; - - cpu1: cpu@1 { -@@ -94,6 +95,12 @@ - enable-method = "psci"; - clock-frequency = <1300000000>; - cci-control-port = <&cci_control2>; -+ next-level-cache = <&L2>; -+ }; -+ -+ L2: l2-cache { -+ compatible = "cache"; -+ cache-level = <2>; - }; - }; - diff --git a/target/linux/mediatek/patches-5.15/192-v5.19-arm64-dts-mt7622-specify-the-number-of-DMA-requests.patch b/target/linux/mediatek/patches-5.15/192-v5.19-arm64-dts-mt7622-specify-the-number-of-DMA-requests.patch deleted file mode 100644 index 4fef9aea22..0000000000 --- a/target/linux/mediatek/patches-5.15/192-v5.19-arm64-dts-mt7622-specify-the-number-of-DMA-requests.patch +++ /dev/null @@ -1,122 +0,0 @@ -From patchwork Fri Apr 29 08:42:25 2022 -Content-Type: text/plain; charset="utf-8" -MIME-Version: 1.0 -Content-Transfer-Encoding: 7bit -X-Patchwork-Submitter: Rui Salvaterra -X-Patchwork-Id: 12831649 -Return-Path: - -X-Spam-Checker-Version: SpamAssassin 3.4.0 (2014-02-07) on - aws-us-west-2-korg-lkml-1.web.codeaurora.org -Received: from bombadil.infradead.org (bombadil.infradead.org - [198.137.202.133]) - (using TLSv1.2 with cipher ECDHE-RSA-AES256-GCM-SHA384 (256/256 bits)) - (No client certificate requested) - by smtp.lore.kernel.org (Postfix) with ESMTPS id 386E2C433FE - for ; - Fri, 29 Apr 2022 08:43:49 +0000 (UTC) -DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; - d=lists.infradead.org; s=bombadil.20210309; h=Sender: - Content-Transfer-Encoding:Content-Type:List-Subscribe:List-Help:List-Post: - List-Archive:List-Unsubscribe:List-Id:MIME-Version:Message-Id:Date:Subject:Cc - :To:From:Reply-To:Content-ID:Content-Description:Resent-Date:Resent-From: - Resent-Sender:Resent-To:Resent-Cc:Resent-Message-ID:In-Reply-To:References: - List-Owner; bh=8o7lZT3r9rAaTm8HKh4V0xpz9VW91LuZAYfrXGv0Xic=; b=bS+249v3+UY+qs - bxuupjLqBetRQqMAaPjTn6GKQJtca75PMdLf3okoQban7PNqWO9WOgCJWgY2eyzOSjxHBPr1dsGzy - 6c3CZBbMy8pXl/zf80YRmikPFXehOzAvOpZjco4QUCCqXNsJM9FKzAqYIaZDSlLOTmADDepsh481G - k/h/g39ztzn09LVqwF2Bh0DopIbHiq/BepTeU8jFt5GTj3EGPTdCU7Vq7mf2pP6P6oPk6vswKVYaQ - opq96BDGIEpeKViuMWt07vdJX2meQBHhY/Rte/aAO5pdLpusY2OPvEKv0/49swpAEsNYIYFcgtCtm - vaKUqN85QlQznqd/NaHw==; -Received: from localhost ([::1] helo=bombadil.infradead.org) - by bombadil.infradead.org with esmtp (Exim 4.94.2 #2 (Red Hat Linux)) - id 1nkMD3-00AFVb-Co; Fri, 29 Apr 2022 08:42:42 +0000 -Received: from mail-ed1-x534.google.com ([2a00:1450:4864:20::534]) - by bombadil.infradead.org with esmtps (Exim 4.94.2 #2 (Red Hat Linux)) - id 1nkMCy-00AFSn-Rp; Fri, 29 Apr 2022 08:42:38 +0000 -Received: by mail-ed1-x534.google.com with SMTP id be20so8231068edb.12; - Fri, 29 Apr 2022 01:42:33 -0700 (PDT) -DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20210112; - h=from:to:cc:subject:date:message-id:mime-version - :content-transfer-encoding; - bh=XJkVawFXvwQH7kz0CHPfmxuFkQ6+ipcLhCSvCaul0jQ=; - b=HSFxl4yM5hEns1ZYq8D5pL88/nYNfulhELpJyhaF8XIrymlck2o40/lATRsLIEWMyb - 8MiL8d5eAOEMSb7rUrqWodLDPZld7ZzCvoVt6XQeVmJLkAw0teNdQXvlCZgu/3Q6MwUw - Wx+QkzqUjCODOLk224RVZGvnKY9YRu/WmZEnWqBjzQIF90DLNXyni+yS7XbUn8CnPbdM - M3s/Ty7YsgPGsibKem1EI6yma15sXRNi1Vz1o0ArcPpsB/6x/ym8sCQemxSvrmer5ps9 - wrBnmlH558mrlj7rSHK9l5SmsGlkJiXB3DTLSrnynxHTY9gX9lSBsQxxjiqu1sEMvDVY - toUA== -X-Google-DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; - d=1e100.net; s=20210112; - h=x-gm-message-state:from:to:cc:subject:date:message-id:mime-version - :content-transfer-encoding; - bh=XJkVawFXvwQH7kz0CHPfmxuFkQ6+ipcLhCSvCaul0jQ=; - b=LtdsZ9M/Im1hyxdJYYHttN4wtxcqRThm/H/oV8driFRB4KuwxO2iP2OqycVsS1sN2y - quWFM6L8v0KaUZRUR85rRRr8JX9P84kqTu4szOEuSIQQ/aUDUbJxVi7rICLPZ890DqTY - APplzuMhuNr6unYQO5Lxrj5IHHtrsmKP8ttR7VVWPNHpJseXc1kQ+HDLgylQLHVsb/5U - 8KpUG0LvxhvqsNU6HbTwLD/Q/88ELP5MfoWHUocYXKPrBJ8K6rCHsmjH6z6tFLfXgce7 - 619waAHXFhCBCflRbAC+D9VemoNe5wJlu9mzyQ4Xavbo8NZgDobVFWOTEQ1iRdua/oRT - tbxw== -X-Gm-Message-State: AOAM532GrwQ/whp0buK64HysYJy6aLBD/xGE/8Dr7NSW150Jds7jTjor - eVhdzOGjuWywij/s3mwA9XfPjST+Cg== -X-Google-Smtp-Source: - ABdhPJxU9goI5zXE0GQP90hO7TH0IDw++6UHpkGFSUH/chvzvE0L/pQF0XqDkdwzbbTmxsOBUMGcZg== -X-Received: by 2002:a05:6402:84c:b0:423:e5a2:3655 with SMTP id - b12-20020a056402084c00b00423e5a23655mr40374113edz.28.1651221752304; - Fri, 29 Apr 2022 01:42:32 -0700 (PDT) -Received: from crystalwell.adg.lan (a109-49-0-175.cpe.netcabo.pt. - [109.49.0.175]) by smtp.gmail.com with ESMTPSA id - el10-20020a170907284a00b006f3ef214e32sm429064ejc.152.2022.04.29.01.42.31 - (version=TLS1_3 cipher=TLS_AES_256_GCM_SHA384 bits=256/256); - Fri, 29 Apr 2022 01:42:31 -0700 (PDT) -From: Rui Salvaterra -To: linux-arm-kernel@lists.infradead.org, linux-mediatek@lists.infradead.org, - linux-kernel@vger.kernel.org -Cc: matthias.bgg@gmail.com, ryder.lee@mediatek.com, daniel@makrotopia.org, - Rui Salvaterra -Subject: [PATCH] arm64: dts: mt7622: specify the number of DMA requests -Date: Fri, 29 Apr 2022 09:42:25 +0100 -Message-Id: <20220429084225.298213-1-rsalvaterra@gmail.com> -X-Mailer: git-send-email 2.36.0 -MIME-Version: 1.0 -X-CRM114-Version: 20100106-BlameMichelson ( TRE 0.8.0 (BSD) ) MR-646709E3 -X-CRM114-CacheID: sfid-20220429_014236_944696_097D1E73 -X-CRM114-Status: UNSURE ( 8.85 ) -X-CRM114-Notice: Please train this message. -X-BeenThere: linux-arm-kernel@lists.infradead.org -X-Mailman-Version: 2.1.34 -Precedence: list -List-Id: -List-Unsubscribe: - , - -List-Archive: -List-Post: -List-Help: -List-Subscribe: - , - -Sender: "linux-arm-kernel" -Errors-To: - linux-arm-kernel-bounces+linux-arm-kernel=archiver.kernel.org@lists.infradead.org - -The MT7622 device tree never bothered to specify the number of virtual DMA -channels for the HSDMA controller, always falling back to the default value of -3. Make this value explicit, in order to avoid the following dmesg notification: - -mtk_hsdma 1b007000.dma-controller: Using 3 as missing dma-requests property - -Signed-off-by: Rui Salvaterra ---- - arch/arm64/boot/dts/mediatek/mt7622.dtsi | 1 + - 1 file changed, 1 insertion(+) - ---- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi -@@ -942,6 +942,7 @@ - clock-names = "hsdma"; - power-domains = <&scpsys MT7622_POWER_DOMAIN_ETHSYS>; - #dma-cells = <1>; -+ dma-requests = <3>; - }; - - pcie_mirror: pcie-mirror@10000400 { diff --git a/target/linux/mediatek/patches-5.15/193-dts-mt7623-thermal_zone_fix.patch b/target/linux/mediatek/patches-5.15/193-dts-mt7623-thermal_zone_fix.patch deleted file mode 100644 index 1cfb53d620..0000000000 --- a/target/linux/mediatek/patches-5.15/193-dts-mt7623-thermal_zone_fix.patch +++ /dev/null @@ -1,48 +0,0 @@ -From 824d56e753a588fcfd650db1822e34a02a48bb77 Mon Sep 17 00:00:00 2001 -From: Bruno Umuarama -Date: Thu, 13 Oct 2022 21:18:21 +0000 -Subject: [PATCH] mediatek: mt7623: fix thermal zone -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -Raising the temperatures for passive and active trips. @VA1DER -proposed at issue 9396 to remove passive trip. This commit relates to -his suggestion. - -Without this patch. the CPU will be throttled all the way down to 98MHz -if the temperature rises even a degree above the trip point, and it was -further discovered that if the internal temperature of the device is -above the first trip point temperature when it boots then it will start -in a throttled state and even -$ echo disabled > /sys/class/thermal/thermal_zone0/mode -will have no effect. - -The patch increases the passive trip point and active cooling map. The -throttling temperature will then be at 77°C and 82°C, which is still a -low enough temperature for ARM devices to not be in the real danger -zone, and gives some operational headroom. - -Signed-off-by: Bruno Umuarama ---- - arch/arm/boot/dts/mt7623.dtsi | 4 ++-- - 1 file changed, 2 insertions(+), 2 deletions(-) - ---- a/arch/arm/boot/dts/mt7623.dtsi -+++ b/arch/arm/boot/dts/mt7623.dtsi -@@ -160,13 +160,13 @@ - - trips { - cpu_passive: cpu-passive { -- temperature = <57000>; -+ temperature = <77000>; - hysteresis = <2000>; - type = "passive"; - }; - - cpu_active: cpu-active { -- temperature = <67000>; -+ temperature = <82000>; - hysteresis = <2000>; - type = "active"; - }; diff --git a/target/linux/mediatek/patches-5.15/194-dts-mt7968a-add-ramoops.patch b/target/linux/mediatek/patches-5.15/194-dts-mt7968a-add-ramoops.patch deleted file mode 100644 index 161c1e7516..0000000000 --- a/target/linux/mediatek/patches-5.15/194-dts-mt7968a-add-ramoops.patch +++ /dev/null @@ -1,17 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi -@@ -68,6 +68,14 @@ - #address-cells = <2>; - #size-cells = <2>; - ranges; -+ -+ /* 64 KiB reserved for ramoops/pstore */ -+ ramoops@42ff0000 { -+ compatible = "ramoops"; -+ reg = <0 0x42ff0000 0 0x10000>; -+ record-size = <0x1000>; -+ }; -+ - /* 192 KiB reserved for ARM Trusted Firmware (BL31) */ - secmon_reserved: secmon@43000000 { - reg = <0 0x43000000 0 0x30000>; diff --git a/target/linux/mediatek/patches-5.15/195-dts-mt7986a-bpi-r3-leds-port-names-and-wifi-eeprom.patch b/target/linux/mediatek/patches-5.15/195-dts-mt7986a-bpi-r3-leds-port-names-and-wifi-eeprom.patch deleted file mode 100644 index 336920bafe..0000000000 --- a/target/linux/mediatek/patches-5.15/195-dts-mt7986a-bpi-r3-leds-port-names-and-wifi-eeprom.patch +++ /dev/null @@ -1,196 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts -+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dts -@@ -23,6 +23,10 @@ - serial0 = &uart0; - ethernet0 = &gmac0; - ethernet1 = &gmac1; -+ led-boot = &green_led; -+ led-failsafe = &green_led; -+ led-running = &green_led; -+ led-upgrade = &blue_led; - }; - - chosen { -@@ -419,27 +423,27 @@ - - port@1 { - reg = <1>; -- label = "lan0"; -+ label = "lan1"; - }; - - port@2 { - reg = <2>; -- label = "lan1"; -+ label = "lan2"; - }; - - port@3 { - reg = <3>; -- label = "lan2"; -+ label = "lan3"; - }; - - port@4 { - reg = <4>; -- label = "lan3"; -+ label = "lan4"; - }; - - port5: port@5 { - reg = <5>; -- label = "lan4"; -+ label = "sfp2"; - phy-mode = "2500base-x"; - sfp = <&sfp2>; - managed = "in-band-status"; -@@ -490,9 +494,137 @@ - - &wifi { - status = "okay"; -- pinctrl-names = "default", "dbdc"; -+ pinctrl-names = "default"; - pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>; -- pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>; -+ -+ mediatek,eeprom-data = <0x86790900 0x000c4326 0x60000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x01000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000800 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x24649090 0x00280000 0x05100000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00021e00 0x021e0002 0x1e00021e 0x00022800 0x02280002 0x28000228 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00008080 0x8080fdf7 -+ 0x0903150d 0x80808080 0x80808080 0x05050d0d 0x1313c6c6 0xc3c3c200 0x00c200c2 0x00008182 -+ 0x8585c2c2 0x82828282 0x858500c2 0xc2000081 0x82858587 0x87c2c200 0x81818285 0x858787c2 -+ 0xc2000081 0x82858587 0x87c2c200 0x00818285 0x858787c2 0xc2000081 0x82858587 0x87c4c4c2 -+ 0xc100c300 0xc3c3c100 0x818383c3 0xc3c3c100 0x81838300 0xc2c2c2c0 0x81828484 0x000000c3 -+ 0xc3c3c100 0x81838386 0x86c3c3c3 0xc1008183 0x838686c2 0xc2c2c081 0x82848486 0x86c3c3c3 -+ 0xc1008183 0x838686c3 0xc3c3c100 0x81838386 0x86c3c3c3 0xc1008183 0x83868622 0x28002228 -+ 0x00222800 0x22280000 0xdddddddd 0xdddddddd 0xddbbbbbb 0xccccccdd 0xdddddddd 0xdddddddd -+ 0xeeeeeecc 0xccccdddd 0xdddddddd 0x004a5662 0x0000004a 0x56620000 0x004a5662 0x0000004a -+ 0x56620000 0x88888888 0x33333326 0x26262626 0x26262600 0x33333326 0x26262626 0x26262600 -+ 0x33333326 0x26262626 0x26262600 0x33333326 0x26262626 0x26262600 0x00000000 0xf0f0cc00 -+ 0x00000000 0x0000aaaa 0xaabbbbbb 0xcccccccc 0xccccbbbb 0xbbbbbbbb 0xbbbbbbaa 0xaaaabbbb -+ 0xbbaaaaaa 0x999999aa 0xaaaabbbb 0xbbcccccc 0x00000000 0x0000aaaa 0xaa000000 0xbbbbbbbb -+ 0xbbbbaaaa 0xaa999999 0xaaaaaaaa 0xaaaaaaaa 0xaaaaaaaa 0xaaaaaaaa 0xaaaabbbb 0xbbbbbbbb -+ 0x00000000 0x00000000 0x00000000 0x99999999 0x9999aaaa 0xaaaaaaaa 0x999999aa 0xaaaaaaaa -+ 0xaaaaaaaa 0xaaaaaaaa 0xaaaabbbb 0xbbbbbbbb 0x00000000 0x0000eeee 0xeeffffff 0xcccccccc -+ 0xccccdddd 0xddbbbbbb 0xccccccbb 0xbbbbbbbb 0xbbbbbbbb 0xbbbbbbbb 0xbbbbcccc 0xccdddddd -+ 0x00516200 0x686e0051 0x6200686e 0x00516200 0x686e0051 0x6200686e 0x00516200 0x686e0051 -+ 0x6200686e 0x00516200 0x686e0051 0x6200686e 0x00516200 0x686e0051 0x6200686e 0x00516200 -+ 0x686e0051 0x6200686e 0x00516200 0x686e0051 0x6200686e 0x00516200 0x686e0051 0x6200686e -+ 0x00516200 0x686e0051 0x6200686e 0x00516200 0x686e0051 0x6200686e 0x00516200 0x686e0051 -+ 0x6200686e 0x00516200 0x686e0051 0x6200686e 0x00516200 0x686e0051 0x6200686e 0x00516200 -+ 0x686e0051 0x6200686e 0x00516200 0x686e0051 0x6200686e 0x00516200 0x686e0051 0x6200686e -+ 0x88888888 0x88888888 0x88888888 0x88888888 0x88888888 0x88888888 0x88888888 0x88888888 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000001 0x06000100 0x01050002 0x00ff0300 -+ 0xf900fe03 0x00000000 0x00000000 0x0000009b 0x6e370000 0x00000000 0x00fc0009 0x0a00fe00 -+ 0x060700fe 0x00070800 0x05000b0a 0x00000000 0x00000000 0x000000e2 0x96460000 0x00000000 -+ 0x000400f7 0xf8000300 0xfcfe0003 0x00fbfc00 0xee00e3f2 0x00000000 0x00000000 0x00000011 -+ 0xbb550000 0x00000000 0x000600f6 0xfc000300 0xfbfe0004 0x00fafe00 0xf600ecf2 0x00000000 -+ 0x00000000 0x0000001f 0xbf580000 0x00000000 0x000600f5 0xf6000400 0xf8f90004 0x00f7f800 -+ 0xf700f0f4 0x00000000 0x00000000 0x00000024 0xbe570000 0x00000000 0x000800f8 0xfe000600 -+ 0xf8fd0007 0x00f9fe00 0xf500f0f4 0x00000000 0x00000000 0x0000002d 0xd6610000 0x00000000 -+ 0x000400f7 0xfc000500 0xf7fc0005 0x00f7fc00 0xf900f5f8 0x00000000 0x00000000 0x00000026 -+ 0xd96e0000 0x00000000 0x000400f7 0xf9000600 0xf5f70005 0x00f5f800 0xf900f4f7 0x00000000 -+ 0x00000000 0x0000001b 0xce690000 0x00000000 0x000300f8 0xf8000600 0xf6f60004 0x00f6f700 -+ 0xf900f4f7 0x00000000 0x00000000 0x00000018 0xd8720000 0x00000000 0x00000000 0x02404002 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0xc1c2c1c2 0x41c341c3 0x3fc13fc1 0x40c13fc2 0x3fc240c1 0x41c040c0 0x3fc23fc2 0x40c13fc2 -+ 0x3fc140c0 0x41c040c0 0x3fc33fc3 0x40c23fc2 0x3fc240c1 0x41c040c0 0x3fc23fc2 0x40c23fc2 -+ 0x3fc140c1 0x41c040c0 0x00000000 0x00000000 0x41c741c7 0xc1c7c1c7 0x00000000 0x00000000 -+ 0x3fc03fc0 0x3fc03fc0 0x3fc03fc0 0x3fc03fc0 0x3fc03fc0 0x3fc03fc0 0x3fc03fc0 0x3fc03fc0 -+ 0x3fc03fc0 0x3fc03fc0 0x3fc03fc0 0x3fc03fc0 0x3fc03fc0 0x3fc03fc0 0x3fc03fc0 0x3fc03fc0 -+ 0x00a0ce00 0x00000000 0xb6840000 0x00000000 0x00000000 0x00000000 0x18181818 0x18181818 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x004b5763 0x0000004b 0x57630000 0x004b5763 0x0000004b 0x57630000 0x88888888 0x08474759 -+ 0x69780849 0x49596d7a 0x0849495a 0x6d790848 0x48596c78 0x08484858 0x6a780848 0x48586a78 -+ 0x08484858 0x6c78084a 0x4a5b6d79 0x08474759 0x697a0848 0x48596b79 0x08484859 0x6c7a0848 -+ 0x48586c79 0x08484857 0x68770848 0x48576877 0x08484857 0x6a77084a 0x4a5a6a77 0x08464659 -+ 0x69790848 0x48586b79 0x08484858 0x6c7a0848 0x48596c79 0x08484857 0x68770848 0x48576877 -+ 0x08494958 0x6d7a084b 0x4b5c6c77 0x0847475a 0x6a7b0849 0x495a6e7c 0x0849495a 0x6e7c0849 -+ 0x495b6e7c 0x08494959 0x6a7a0849 0x49596a7a 0x084a4a5a 0x6f7d084b 0x4b5c6e7b 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x85848484 -+ 0xc3c4c4c5 0xc4c3c33f 0xc3c3c2c2 0xc2c2c03f 0xc3c3c3c4 0xc4c4c33f 0xc2c2c2c2 0xc1c3c1c1 -+ 0xc0c08282 0x83848686 0x88880000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00001111 0x00000000 -+ 0x8080f703 0x10808080 0x80050d13 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x000000a4 0xce000000 0x0000b684 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 -+ 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000>; - - led { - led-active-low; ---- a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso -+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dtso -@@ -55,6 +55,7 @@ - partition@c00000 { - label = "fit"; - reg = <0xc00000 0x1400000>; -+ compatible = "denx,fit"; - }; - }; - }; diff --git a/target/linux/mediatek/patches-5.15/200-phy-phy-mtk-tphy-Add-hifsys-support.patch b/target/linux/mediatek/patches-5.15/200-phy-phy-mtk-tphy-Add-hifsys-support.patch deleted file mode 100644 index cfb0556d1e..0000000000 --- a/target/linux/mediatek/patches-5.15/200-phy-phy-mtk-tphy-Add-hifsys-support.patch +++ /dev/null @@ -1,66 +0,0 @@ -From 28f9a5e2a3f5441ab5594669ed82da11e32277a9 Mon Sep 17 00:00:00 2001 -From: Kristian Evensen -Date: Mon, 30 Apr 2018 14:38:01 +0200 -Subject: [PATCH] phy: phy-mtk-tphy: Add hifsys-support - ---- - drivers/phy/mediatek/phy-mtk-tphy.c | 20 ++++++++++++++++++++ - 1 file changed, 20 insertions(+) - ---- a/drivers/phy/mediatek/phy-mtk-tphy.c -+++ b/drivers/phy/mediatek/phy-mtk-tphy.c -@@ -18,6 +18,8 @@ - #include - #include - #include -+#include -+#include - - /* version V1 sub-banks offset base address */ - /* banks shared by multiple phys */ -@@ -311,6 +313,9 @@ - - #define TPHY_CLKS_CNT 2 - -+#define HIF_SYSCFG1 0x14 -+#define HIF_SYSCFG1_PHY2_MASK (0x3 << 20) -+ - enum mtk_phy_version { - MTK_PHY_V1 = 1, - MTK_PHY_V2, -@@ -377,6 +382,7 @@ struct mtk_tphy { - void __iomem *sif_base; /* only shared sif */ - const struct mtk_phy_pdata *pdata; - struct mtk_phy_instance **phys; -+ struct regmap *hif; - int nphys; - int src_ref_clk; /* MHZ, reference clock for slew rate calibrate */ - int src_coef; /* coefficient for slew rate calibrate */ -@@ -730,6 +736,10 @@ static void pcie_phy_instance_init(struc - if (tphy->pdata->version != MTK_PHY_V1) - return; - -+ if (tphy->hif) -+ regmap_update_bits(tphy->hif, HIF_SYSCFG1, -+ HIF_SYSCFG1_PHY2_MASK, 0); -+ - tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG0); - tmp &= ~(P3A_RG_XTAL_EXT_PE1H | P3A_RG_XTAL_EXT_PE2H); - tmp |= P3A_RG_XTAL_EXT_PE1H_VAL(0x2) | P3A_RG_XTAL_EXT_PE2H_VAL(0x2); -@@ -1437,6 +1447,16 @@ static int mtk_tphy_probe(struct platfor - &tphy->src_coef); - } - -+ if (of_find_property(np, "mediatek,phy-switch", NULL)) { -+ tphy->hif = syscon_regmap_lookup_by_phandle(np, -+ "mediatek,phy-switch"); -+ if (IS_ERR(tphy->hif)) { -+ dev_err(&pdev->dev, -+ "missing \"mediatek,phy-switch\" phandle\n"); -+ return PTR_ERR(tphy->hif); -+ } -+ } -+ - port = 0; - for_each_child_of_node(np, child_np) { - struct mtk_phy_instance *instance; diff --git a/target/linux/mediatek/patches-5.15/210-v6.1-pinctrl-mediatek-add-support-for-MT7986-SoC.patch b/target/linux/mediatek/patches-5.15/210-v6.1-pinctrl-mediatek-add-support-for-MT7986-SoC.patch deleted file mode 100644 index 0761e1da18..0000000000 --- a/target/linux/mediatek/patches-5.15/210-v6.1-pinctrl-mediatek-add-support-for-MT7986-SoC.patch +++ /dev/null @@ -1,26 +0,0 @@ ---- a/drivers/pinctrl/mediatek/Kconfig -+++ b/drivers/pinctrl/mediatek/Kconfig -@@ -120,6 +120,13 @@ config PINCTRL_MT7622 - default ARM64 && ARCH_MEDIATEK - select PINCTRL_MTK_MOORE - -+config PINCTRL_MT7986 -+ bool "Mediatek MT7986 pin control" -+ depends on OF -+ depends on ARM64 || COMPILE_TEST -+ default ARM64 && ARCH_MEDIATEK -+ select PINCTRL_MTK_MOORE -+ - config PINCTRL_MT8167 - bool "Mediatek MT8167 pin control" - depends on OF ---- a/drivers/pinctrl/mediatek/Makefile -+++ b/drivers/pinctrl/mediatek/Makefile -@@ -17,6 +17,7 @@ obj-$(CONFIG_PINCTRL_MT6797) += pinctrl- - obj-$(CONFIG_PINCTRL_MT7622) += pinctrl-mt7622.o - obj-$(CONFIG_PINCTRL_MT7623) += pinctrl-mt7623.o - obj-$(CONFIG_PINCTRL_MT7629) += pinctrl-mt7629.o -+obj-$(CONFIG_PINCTRL_MT7986) += pinctrl-mt7986.o - obj-$(CONFIG_PINCTRL_MT8167) += pinctrl-mt8167.o - obj-$(CONFIG_PINCTRL_MT8173) += pinctrl-mt8173.o - obj-$(CONFIG_PINCTRL_MT8183) += pinctrl-mt8183.o diff --git a/target/linux/mediatek/patches-5.15/211-v5.16-clk-mediatek-Add-API-for-clock-resource-recycle.patch b/target/linux/mediatek/patches-5.15/211-v5.16-clk-mediatek-Add-API-for-clock-resource-recycle.patch deleted file mode 100644 index 15de8aa3d4..0000000000 --- a/target/linux/mediatek/patches-5.15/211-v5.16-clk-mediatek-Add-API-for-clock-resource-recycle.patch +++ /dev/null @@ -1,28 +0,0 @@ ---- a/drivers/clk/mediatek/clk-mtk.c -+++ b/drivers/clk/mediatek/clk-mtk.c -@@ -43,6 +43,15 @@ err_out: - return NULL; - } - -+void mtk_free_clk_data(struct clk_onecell_data *clk_data) -+{ -+ if (!clk_data) -+ return; -+ -+ kfree(clk_data->clks); -+ kfree(clk_data); -+} -+ - void mtk_clk_register_fixed_clks(const struct mtk_fixed_clk *clks, - int num, struct clk_onecell_data *clk_data) - { ---- a/drivers/clk/mediatek/clk-mtk.h -+++ b/drivers/clk/mediatek/clk-mtk.h -@@ -202,6 +202,7 @@ void mtk_clk_register_dividers(const str - struct clk_onecell_data *clk_data); - - struct clk_onecell_data *mtk_alloc_clk_data(unsigned int clk_num); -+void mtk_free_clk_data(struct clk_onecell_data *clk_data); - - #define HAVE_RST_BAR BIT(0) - #define PLL_AO BIT(1) diff --git a/target/linux/mediatek/patches-5.15/212-v5.17-clk-mediatek-add-mt7986-clock-support.patch b/target/linux/mediatek/patches-5.15/212-v5.17-clk-mediatek-add-mt7986-clock-support.patch deleted file mode 100644 index 8e2365a498..0000000000 --- a/target/linux/mediatek/patches-5.15/212-v5.17-clk-mediatek-add-mt7986-clock-support.patch +++ /dev/null @@ -1,39 +0,0 @@ ---- a/drivers/clk/mediatek/Kconfig -+++ b/drivers/clk/mediatek/Kconfig -@@ -344,6 +344,23 @@ config COMMON_CLK_MT7629_HIFSYS - This driver supports MediaTek MT7629 HIFSYS clocks providing - to PCI-E and USB. - -+config COMMON_CLK_MT7986 -+ bool "Clock driver for MediaTek MT7986" -+ depends on ARCH_MEDIATEK || COMPILE_TEST -+ select COMMON_CLK_MEDIATEK -+ default ARCH_MEDIATEK -+ help -+ This driver supports MediaTek MT7986 basic clocks and clocks -+ required for various periperals found on MediaTek. -+ -+config COMMON_CLK_MT7986_ETHSYS -+ bool "Clock driver for MediaTek MT7986 ETHSYS" -+ depends on COMMON_CLK_MT7986 -+ default COMMON_CLK_MT7986 -+ help -+ This driver add support for clocks for Ethernet and SGMII -+ required on MediaTek MT7986 SoC. -+ - config COMMON_CLK_MT8135 - bool "Clock driver for MediaTek MT8135" - depends on (ARCH_MEDIATEK && ARM) || COMPILE_TEST ---- a/drivers/clk/mediatek/Makefile -+++ b/drivers/clk/mediatek/Makefile -@@ -46,6 +46,10 @@ obj-$(CONFIG_COMMON_CLK_MT7622_AUDSYS) + - obj-$(CONFIG_COMMON_CLK_MT7629) += clk-mt7629.o - obj-$(CONFIG_COMMON_CLK_MT7629_ETHSYS) += clk-mt7629-eth.o - obj-$(CONFIG_COMMON_CLK_MT7629_HIFSYS) += clk-mt7629-hif.o -+obj-$(CONFIG_COMMON_CLK_MT7986) += clk-mt7986-apmixed.o -+obj-$(CONFIG_COMMON_CLK_MT7986) += clk-mt7986-topckgen.o -+obj-$(CONFIG_COMMON_CLK_MT7986) += clk-mt7986-infracfg.o -+obj-$(CONFIG_COMMON_CLK_MT7986_ETHSYS) += clk-mt7986-eth.o - obj-$(CONFIG_COMMON_CLK_MT8135) += clk-mt8135.o - obj-$(CONFIG_COMMON_CLK_MT8167) += clk-mt8167.o - obj-$(CONFIG_COMMON_CLK_MT8167_AUDSYS) += clk-mt8167-aud.o diff --git a/target/linux/mediatek/patches-5.15/213-spi-mediatek-add-mt7986-spi-support.patch b/target/linux/mediatek/patches-5.15/213-spi-mediatek-add-mt7986-spi-support.patch deleted file mode 100644 index 04da1765f3..0000000000 --- a/target/linux/mediatek/patches-5.15/213-spi-mediatek-add-mt7986-spi-support.patch +++ /dev/null @@ -1,917 +0,0 @@ -From 7d99750f96fc6904d54affebdc8c9b0bfae1e9e8 Mon Sep 17 00:00:00 2001 -From: Sam Shih -Date: Sun, 17 Apr 2022 11:40:22 +0800 -Subject: [PATCH] spi: mediatek: backport document and driver to support mt7986 - spi design - -this patch add the support of ipm design and upgrade devicetree binding - -The patch is comming from following threads -- https://lore.kernel.org/all/20220315032411.2826-1-leilk.liu@mediatek.com/ -- https://lore.kernel.org/all/20220401071616.8874-1-leilk.liu@mediatek.com/ - -Signed-off-by: Sam Shih ---- - .../bindings/spi/mediatek,spi-mt65xx.yaml | 111 ++++ - drivers/spi/spi-mt65xx.c | 509 ++++++++++++++++-- - 2 files changed, 572 insertions(+), 48 deletions(-) - create mode 100644 Documentation/devicetree/bindings/spi/mediatek,spi-mt65xx.yaml - ---- /dev/null -+++ b/Documentation/devicetree/bindings/spi/mediatek,spi-mt65xx.yaml -@@ -0,0 +1,111 @@ -+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) -+%YAML 1.2 -+--- -+$id: http://devicetree.org/schemas/spi/mediatek,spi-mt65xx.yaml# -+$schema: http://devicetree.org/meta-schemas/core.yaml# -+ -+title: SPI Bus controller for MediaTek ARM SoCs -+ -+maintainers: -+ - Leilk Liu -+ -+allOf: -+ - $ref: "/schemas/spi/spi-controller.yaml#" -+ -+properties: -+ compatible: -+ oneOf: -+ - items: -+ - enum: -+ - mediatek,mt7629-spi -+ - const: mediatek,mt7622-spi -+ - items: -+ - enum: -+ - mediatek,mt8516-spi -+ - const: mediatek,mt2712-spi -+ - items: -+ - enum: -+ - mediatek,mt6779-spi -+ - mediatek,mt8186-spi -+ - mediatek,mt8192-spi -+ - mediatek,mt8195-spi -+ - const: mediatek,mt6765-spi -+ - items: -+ - enum: -+ - mediatek,mt7986-spi-ipm -+ - const: mediatek,spi-ipm -+ - items: -+ - enum: -+ - mediatek,mt2701-spi -+ - mediatek,mt2712-spi -+ - mediatek,mt6589-spi -+ - mediatek,mt6765-spi -+ - mediatek,mt6893-spi -+ - mediatek,mt7622-spi -+ - mediatek,mt8135-spi -+ - mediatek,mt8173-spi -+ - mediatek,mt8183-spi -+ -+ reg: -+ maxItems: 1 -+ -+ interrupts: -+ maxItems: 1 -+ -+ clocks: -+ minItems: 3 -+ items: -+ - description: clock used for the parent clock -+ - description: clock used for the muxes clock -+ - description: clock used for the clock gate -+ - description: clock used for the AHB bus, this clock is optional -+ -+ clock-names: -+ minItems: 3 -+ items: -+ - const: parent-clk -+ - const: sel-clk -+ - const: spi-clk -+ - const: hclk -+ -+ mediatek,pad-select: -+ $ref: /schemas/types.yaml#/definitions/uint32-array -+ minItems: 1 -+ maxItems: 4 -+ items: -+ enum: [0, 1, 2, 3] -+ description: -+ specify which pins group(ck/mi/mo/cs) spi controller used. -+ This is an array. -+ -+required: -+ - compatible -+ - reg -+ - interrupts -+ - clocks -+ - clock-names -+ - '#address-cells' -+ - '#size-cells' -+ -+unevaluatedProperties: false -+ -+examples: -+ - | -+ #include -+ #include -+ #include -+ #include -+ -+ spi@1100a000 { -+ compatible = "mediatek,mt8173-spi"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ reg = <0x1100a000 0x1000>; -+ interrupts = ; -+ clocks = <&topckgen CLK_TOP_SYSPLL3_D2>, -+ <&topckgen CLK_TOP_SPI_SEL>, -+ <&pericfg CLK_PERI_SPI0>; -+ clock-names = "parent-clk", "sel-clk", "spi-clk"; -+ cs-gpios = <&pio 105 GPIO_ACTIVE_LOW>, <&pio 72 GPIO_ACTIVE_LOW>; -+ mediatek,pad-select = <1>, <0>; -+ }; ---- a/drivers/spi/spi-mt65xx.c -+++ b/drivers/spi/spi-mt65xx.c -@@ -12,11 +12,12 @@ - #include - #include - #include --#include -+#include - #include - #include - #include - #include -+#include - #include - - #define SPI_CFG0_REG 0x0000 -@@ -31,6 +32,7 @@ - #define SPI_CFG2_REG 0x0028 - #define SPI_TX_SRC_REG_64 0x002c - #define SPI_RX_DST_REG_64 0x0030 -+#define SPI_CFG3_IPM_REG 0x0040 - - #define SPI_CFG0_SCK_HIGH_OFFSET 0 - #define SPI_CFG0_SCK_LOW_OFFSET 8 -@@ -51,6 +53,7 @@ - #define SPI_CFG1_CS_IDLE_MASK 0xff - #define SPI_CFG1_PACKET_LOOP_MASK 0xff00 - #define SPI_CFG1_PACKET_LENGTH_MASK 0x3ff0000 -+#define SPI_CFG1_IPM_PACKET_LENGTH_MASK GENMASK(31, 16) - #define SPI_CFG2_SCK_HIGH_OFFSET 0 - #define SPI_CFG2_SCK_LOW_OFFSET 16 - -@@ -71,6 +74,24 @@ - #define SPI_CMD_TX_ENDIAN BIT(15) - #define SPI_CMD_FINISH_IE BIT(16) - #define SPI_CMD_PAUSE_IE BIT(17) -+#define SPI_CMD_IPM_NONIDLE_MODE BIT(19) -+#define SPI_CMD_IPM_SPIM_LOOP BIT(21) -+#define SPI_CMD_IPM_GET_TICKDLY_OFFSET 22 -+ -+#define SPI_CMD_IPM_GET_TICKDLY_MASK GENMASK(24, 22) -+ -+#define PIN_MODE_CFG(x) ((x) / 2) -+ -+#define SPI_CFG3_IPM_HALF_DUPLEX_DIR BIT(2) -+#define SPI_CFG3_IPM_HALF_DUPLEX_EN BIT(3) -+#define SPI_CFG3_IPM_XMODE_EN BIT(4) -+#define SPI_CFG3_IPM_NODATA_FLAG BIT(5) -+#define SPI_CFG3_IPM_CMD_BYTELEN_OFFSET 8 -+#define SPI_CFG3_IPM_ADDR_BYTELEN_OFFSET 12 -+ -+#define SPI_CFG3_IPM_CMD_PIN_MODE_MASK GENMASK(1, 0) -+#define SPI_CFG3_IPM_CMD_BYTELEN_MASK GENMASK(11, 8) -+#define SPI_CFG3_IPM_ADDR_BYTELEN_MASK GENMASK(15, 12) - - #define MT8173_SPI_MAX_PAD_SEL 3 - -@@ -81,6 +102,9 @@ - - #define MTK_SPI_MAX_FIFO_SIZE 32U - #define MTK_SPI_PACKET_SIZE 1024 -+#define MTK_SPI_IPM_PACKET_SIZE SZ_64K -+#define MTK_SPI_IPM_PACKET_LOOP SZ_256 -+ - #define MTK_SPI_32BITS_MASK (0xffffffff) - - #define DMA_ADDR_EXT_BITS (36) -@@ -96,6 +120,8 @@ struct mtk_spi_compatible { - bool dma_ext; - /* some IC no need unprepare SPI clk */ - bool no_need_unprepare; -+ /* IPM design adjust and extend register to support more features */ -+ bool ipm_design; - }; - - struct mtk_spi { -@@ -103,7 +129,7 @@ struct mtk_spi { - u32 state; - int pad_num; - u32 *pad_sel; -- struct clk *parent_clk, *sel_clk, *spi_clk; -+ struct clk *parent_clk, *sel_clk, *spi_clk, *spi_hclk; - struct spi_transfer *cur_transfer; - u32 xfer_len; - u32 num_xfered; -@@ -111,6 +137,11 @@ struct mtk_spi { - u32 tx_sgl_len, rx_sgl_len; - const struct mtk_spi_compatible *dev_comp; - u32 spi_clk_hz; -+ struct completion spimem_done; -+ bool use_spimem; -+ struct device *dev; -+ dma_addr_t tx_dma; -+ dma_addr_t rx_dma; - }; - - static const struct mtk_spi_compatible mtk_common_compat; -@@ -119,6 +150,12 @@ static const struct mtk_spi_compatible m - .must_tx = true, - }; - -+static const struct mtk_spi_compatible mtk_ipm_compat = { -+ .enhance_timing = true, -+ .dma_ext = true, -+ .ipm_design = true, -+}; -+ - static const struct mtk_spi_compatible mt6765_compat = { - .need_pad_sel = true, - .must_tx = true, -@@ -160,6 +197,9 @@ static const struct mtk_chip_config mtk_ - }; - - static const struct of_device_id mtk_spi_of_match[] = { -+ { .compatible = "mediatek,spi-ipm", -+ .data = (void *)&mtk_ipm_compat, -+ }, - { .compatible = "mediatek,mt2701-spi", - .data = (void *)&mtk_common_compat, - }, -@@ -278,12 +318,11 @@ static int mtk_spi_set_hw_cs_timing(stru - return 0; - } - --static int mtk_spi_prepare_message(struct spi_master *master, -- struct spi_message *msg) -+static int mtk_spi_hw_init(struct spi_master *master, -+ struct spi_device *spi) - { - u16 cpha, cpol; - u32 reg_val; -- struct spi_device *spi = msg->spi; - struct mtk_chip_config *chip_config = spi->controller_data; - struct mtk_spi *mdata = spi_master_get_devdata(master); - -@@ -291,6 +330,15 @@ static int mtk_spi_prepare_message(struc - cpol = spi->mode & SPI_CPOL ? 1 : 0; - - reg_val = readl(mdata->base + SPI_CMD_REG); -+ if (mdata->dev_comp->ipm_design) { -+ /* SPI transfer without idle time until packet length done */ -+ reg_val |= SPI_CMD_IPM_NONIDLE_MODE; -+ if (spi->mode & SPI_LOOP) -+ reg_val |= SPI_CMD_IPM_SPIM_LOOP; -+ else -+ reg_val &= ~SPI_CMD_IPM_SPIM_LOOP; -+ } -+ - if (cpha) - reg_val |= SPI_CMD_CPHA; - else -@@ -348,23 +396,39 @@ static int mtk_spi_prepare_message(struc - mdata->base + SPI_PAD_SEL_REG); - - /* tick delay */ -- reg_val = readl(mdata->base + SPI_CFG1_REG); - if (mdata->dev_comp->enhance_timing) { -- reg_val &= ~SPI_CFG1_GET_TICK_DLY_MASK; -- reg_val |= ((chip_config->tick_delay & 0x7) -- << SPI_CFG1_GET_TICK_DLY_OFFSET); -+ if (mdata->dev_comp->ipm_design) { -+ reg_val = readl(mdata->base + SPI_CMD_REG); -+ reg_val &= ~SPI_CMD_IPM_GET_TICKDLY_MASK; -+ reg_val |= ((chip_config->tick_delay & 0x7) -+ << SPI_CMD_IPM_GET_TICKDLY_OFFSET); -+ writel(reg_val, mdata->base + SPI_CMD_REG); -+ } else { -+ reg_val = readl(mdata->base + SPI_CFG1_REG); -+ reg_val &= ~SPI_CFG1_GET_TICK_DLY_MASK; -+ reg_val |= ((chip_config->tick_delay & 0x7) -+ << SPI_CFG1_GET_TICK_DLY_OFFSET); -+ writel(reg_val, mdata->base + SPI_CFG1_REG); -+ } - } else { -+ reg_val = readl(mdata->base + SPI_CFG1_REG); - reg_val &= ~SPI_CFG1_GET_TICK_DLY_MASK_V1; - reg_val |= ((chip_config->tick_delay & 0x3) - << SPI_CFG1_GET_TICK_DLY_OFFSET_V1); -+ writel(reg_val, mdata->base + SPI_CFG1_REG); - } -- writel(reg_val, mdata->base + SPI_CFG1_REG); - - /* set hw cs timing */ - mtk_spi_set_hw_cs_timing(spi); - return 0; - } - -+static int mtk_spi_prepare_message(struct spi_master *master, -+ struct spi_message *msg) -+{ -+ return mtk_spi_hw_init(master, msg->spi); -+} -+ - static void mtk_spi_set_cs(struct spi_device *spi, bool enable) - { - u32 reg_val; -@@ -386,13 +450,13 @@ static void mtk_spi_set_cs(struct spi_de - } - - static void mtk_spi_prepare_transfer(struct spi_master *master, -- struct spi_transfer *xfer) -+ u32 speed_hz) - { - u32 div, sck_time, reg_val; - struct mtk_spi *mdata = spi_master_get_devdata(master); - -- if (xfer->speed_hz < mdata->spi_clk_hz / 2) -- div = DIV_ROUND_UP(mdata->spi_clk_hz, xfer->speed_hz); -+ if (speed_hz < mdata->spi_clk_hz / 2) -+ div = DIV_ROUND_UP(mdata->spi_clk_hz, speed_hz); - else - div = 1; - -@@ -423,12 +487,24 @@ static void mtk_spi_setup_packet(struct - u32 packet_size, packet_loop, reg_val; - struct mtk_spi *mdata = spi_master_get_devdata(master); - -- packet_size = min_t(u32, mdata->xfer_len, MTK_SPI_PACKET_SIZE); -+ if (mdata->dev_comp->ipm_design) -+ packet_size = min_t(u32, -+ mdata->xfer_len, -+ MTK_SPI_IPM_PACKET_SIZE); -+ else -+ packet_size = min_t(u32, -+ mdata->xfer_len, -+ MTK_SPI_PACKET_SIZE); -+ - packet_loop = mdata->xfer_len / packet_size; - - reg_val = readl(mdata->base + SPI_CFG1_REG); -- reg_val &= ~(SPI_CFG1_PACKET_LENGTH_MASK | SPI_CFG1_PACKET_LOOP_MASK); -+ if (mdata->dev_comp->ipm_design) -+ reg_val &= ~SPI_CFG1_IPM_PACKET_LENGTH_MASK; -+ else -+ reg_val &= ~SPI_CFG1_PACKET_LENGTH_MASK; - reg_val |= (packet_size - 1) << SPI_CFG1_PACKET_LENGTH_OFFSET; -+ reg_val &= ~SPI_CFG1_PACKET_LOOP_MASK; - reg_val |= (packet_loop - 1) << SPI_CFG1_PACKET_LOOP_OFFSET; - writel(reg_val, mdata->base + SPI_CFG1_REG); - } -@@ -523,7 +599,7 @@ static int mtk_spi_fifo_transfer(struct - mdata->cur_transfer = xfer; - mdata->xfer_len = min(MTK_SPI_MAX_FIFO_SIZE, xfer->len); - mdata->num_xfered = 0; -- mtk_spi_prepare_transfer(master, xfer); -+ mtk_spi_prepare_transfer(master, xfer->speed_hz); - mtk_spi_setup_packet(master); - - if (xfer->tx_buf) { -@@ -556,7 +632,7 @@ static int mtk_spi_dma_transfer(struct s - mdata->cur_transfer = xfer; - mdata->num_xfered = 0; - -- mtk_spi_prepare_transfer(master, xfer); -+ mtk_spi_prepare_transfer(master, xfer->speed_hz); - - cmd = readl(mdata->base + SPI_CMD_REG); - if (xfer->tx_buf) -@@ -591,6 +667,19 @@ static int mtk_spi_transfer_one(struct s - struct spi_device *spi, - struct spi_transfer *xfer) - { -+ struct mtk_spi *mdata = spi_master_get_devdata(spi->master); -+ u32 reg_val = 0; -+ -+ /* prepare xfer direction and duplex mode */ -+ if (mdata->dev_comp->ipm_design) { -+ if (!xfer->tx_buf || !xfer->rx_buf) { -+ reg_val |= SPI_CFG3_IPM_HALF_DUPLEX_EN; -+ if (xfer->rx_buf) -+ reg_val |= SPI_CFG3_IPM_HALF_DUPLEX_DIR; -+ } -+ writel(reg_val, mdata->base + SPI_CFG3_IPM_REG); -+ } -+ - if (master->can_dma(master, spi, xfer)) - return mtk_spi_dma_transfer(master, spi, xfer); - else -@@ -614,8 +703,9 @@ static int mtk_spi_setup(struct spi_devi - if (!spi->controller_data) - spi->controller_data = (void *)&mtk_default_chip_info; - -- if (mdata->dev_comp->need_pad_sel && gpio_is_valid(spi->cs_gpio)) -- gpio_direction_output(spi->cs_gpio, !(spi->mode & SPI_CS_HIGH)); -+ if (mdata->dev_comp->need_pad_sel && spi->cs_gpiod) -+ /* CS de-asserted, gpiolib will handle inversion */ -+ gpiod_direction_output(spi->cs_gpiod, 0); - - return 0; - } -@@ -633,6 +723,12 @@ static irqreturn_t mtk_spi_interrupt(int - else - mdata->state = MTK_SPI_IDLE; - -+ /* SPI-MEM ops */ -+ if (mdata->use_spimem) { -+ complete(&mdata->spimem_done); -+ return IRQ_HANDLED; -+ } -+ - if (!master->can_dma(master, NULL, trans)) { - if (trans->rx_buf) { - cnt = mdata->xfer_len / 4; -@@ -716,6 +812,274 @@ static irqreturn_t mtk_spi_interrupt(int - return IRQ_HANDLED; - } - -+static int mtk_spi_mem_adjust_op_size(struct spi_mem *mem, -+ struct spi_mem_op *op) -+{ -+ int opcode_len; -+ -+ if (op->data.dir != SPI_MEM_NO_DATA) { -+ opcode_len = 1 + op->addr.nbytes + op->dummy.nbytes; -+ if (opcode_len + op->data.nbytes > MTK_SPI_IPM_PACKET_SIZE) { -+ op->data.nbytes = MTK_SPI_IPM_PACKET_SIZE - opcode_len; -+ /* force data buffer dma-aligned. */ -+ op->data.nbytes -= op->data.nbytes % 4; -+ } -+ } -+ -+ return 0; -+} -+ -+static bool mtk_spi_mem_supports_op(struct spi_mem *mem, -+ const struct spi_mem_op *op) -+{ -+ if (!spi_mem_default_supports_op(mem, op)) -+ return false; -+ -+ if (op->addr.nbytes && op->dummy.nbytes && -+ op->addr.buswidth != op->dummy.buswidth) -+ return false; -+ -+ if (op->addr.nbytes + op->dummy.nbytes > 16) -+ return false; -+ -+ if (op->data.nbytes > MTK_SPI_IPM_PACKET_SIZE) { -+ if (op->data.nbytes / MTK_SPI_IPM_PACKET_SIZE > -+ MTK_SPI_IPM_PACKET_LOOP || -+ op->data.nbytes % MTK_SPI_IPM_PACKET_SIZE != 0) -+ return false; -+ } -+ -+ return true; -+} -+ -+static void mtk_spi_mem_setup_dma_xfer(struct spi_master *master, -+ const struct spi_mem_op *op) -+{ -+ struct mtk_spi *mdata = spi_master_get_devdata(master); -+ -+ writel((u32)(mdata->tx_dma & MTK_SPI_32BITS_MASK), -+ mdata->base + SPI_TX_SRC_REG); -+#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT -+ if (mdata->dev_comp->dma_ext) -+ writel((u32)(mdata->tx_dma >> 32), -+ mdata->base + SPI_TX_SRC_REG_64); -+#endif -+ -+ if (op->data.dir == SPI_MEM_DATA_IN) { -+ writel((u32)(mdata->rx_dma & MTK_SPI_32BITS_MASK), -+ mdata->base + SPI_RX_DST_REG); -+#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT -+ if (mdata->dev_comp->dma_ext) -+ writel((u32)(mdata->rx_dma >> 32), -+ mdata->base + SPI_RX_DST_REG_64); -+#endif -+ } -+} -+ -+static int mtk_spi_transfer_wait(struct spi_mem *mem, -+ const struct spi_mem_op *op) -+{ -+ struct mtk_spi *mdata = spi_master_get_devdata(mem->spi->master); -+ /* -+ * For each byte we wait for 8 cycles of the SPI clock. -+ * Since speed is defined in Hz and we want milliseconds, -+ * so it should be 8 * 1000. -+ */ -+ u64 ms = 8000LL; -+ -+ if (op->data.dir == SPI_MEM_NO_DATA) -+ ms *= 32; /* prevent we may get 0 for short transfers. */ -+ else -+ ms *= op->data.nbytes; -+ ms = div_u64(ms, mem->spi->max_speed_hz); -+ ms += ms + 1000; /* 1s tolerance */ -+ -+ if (ms > UINT_MAX) -+ ms = UINT_MAX; -+ -+ if (!wait_for_completion_timeout(&mdata->spimem_done, -+ msecs_to_jiffies(ms))) { -+ dev_err(mdata->dev, "spi-mem transfer timeout\n"); -+ return -ETIMEDOUT; -+ } -+ -+ return 0; -+} -+ -+static int mtk_spi_mem_exec_op(struct spi_mem *mem, -+ const struct spi_mem_op *op) -+{ -+ struct mtk_spi *mdata = spi_master_get_devdata(mem->spi->master); -+ u32 reg_val, nio, tx_size; -+ char *tx_tmp_buf, *rx_tmp_buf; -+ int ret = 0; -+ -+ mdata->use_spimem = true; -+ reinit_completion(&mdata->spimem_done); -+ -+ mtk_spi_reset(mdata); -+ mtk_spi_hw_init(mem->spi->master, mem->spi); -+ mtk_spi_prepare_transfer(mem->spi->master, mem->spi->max_speed_hz); -+ -+ reg_val = readl(mdata->base + SPI_CFG3_IPM_REG); -+ /* opcode byte len */ -+ reg_val &= ~SPI_CFG3_IPM_CMD_BYTELEN_MASK; -+ reg_val |= 1 << SPI_CFG3_IPM_CMD_BYTELEN_OFFSET; -+ -+ /* addr & dummy byte len */ -+ reg_val &= ~SPI_CFG3_IPM_ADDR_BYTELEN_MASK; -+ if (op->addr.nbytes || op->dummy.nbytes) -+ reg_val |= (op->addr.nbytes + op->dummy.nbytes) << -+ SPI_CFG3_IPM_ADDR_BYTELEN_OFFSET; -+ -+ /* data byte len */ -+ if (op->data.dir == SPI_MEM_NO_DATA) { -+ reg_val |= SPI_CFG3_IPM_NODATA_FLAG; -+ writel(0, mdata->base + SPI_CFG1_REG); -+ } else { -+ reg_val &= ~SPI_CFG3_IPM_NODATA_FLAG; -+ mdata->xfer_len = op->data.nbytes; -+ mtk_spi_setup_packet(mem->spi->master); -+ } -+ -+ if (op->addr.nbytes || op->dummy.nbytes) { -+ if (op->addr.buswidth == 1 || op->dummy.buswidth == 1) -+ reg_val |= SPI_CFG3_IPM_XMODE_EN; -+ else -+ reg_val &= ~SPI_CFG3_IPM_XMODE_EN; -+ } -+ -+ if (op->addr.buswidth == 2 || -+ op->dummy.buswidth == 2 || -+ op->data.buswidth == 2) -+ nio = 2; -+ else if (op->addr.buswidth == 4 || -+ op->dummy.buswidth == 4 || -+ op->data.buswidth == 4) -+ nio = 4; -+ else -+ nio = 1; -+ -+ reg_val &= ~SPI_CFG3_IPM_CMD_PIN_MODE_MASK; -+ reg_val |= PIN_MODE_CFG(nio); -+ -+ reg_val |= SPI_CFG3_IPM_HALF_DUPLEX_EN; -+ if (op->data.dir == SPI_MEM_DATA_IN) -+ reg_val |= SPI_CFG3_IPM_HALF_DUPLEX_DIR; -+ else -+ reg_val &= ~SPI_CFG3_IPM_HALF_DUPLEX_DIR; -+ writel(reg_val, mdata->base + SPI_CFG3_IPM_REG); -+ -+ tx_size = 1 + op->addr.nbytes + op->dummy.nbytes; -+ if (op->data.dir == SPI_MEM_DATA_OUT) -+ tx_size += op->data.nbytes; -+ -+ tx_size = max_t(u32, tx_size, 32); -+ -+ tx_tmp_buf = kzalloc(tx_size, GFP_KERNEL | GFP_DMA); -+ if (!tx_tmp_buf) { -+ mdata->use_spimem = false; -+ return -ENOMEM; -+ } -+ -+ tx_tmp_buf[0] = op->cmd.opcode; -+ -+ if (op->addr.nbytes) { -+ int i; -+ -+ for (i = 0; i < op->addr.nbytes; i++) -+ tx_tmp_buf[i + 1] = op->addr.val >> -+ (8 * (op->addr.nbytes - i - 1)); -+ } -+ -+ if (op->dummy.nbytes) -+ memset(tx_tmp_buf + op->addr.nbytes + 1, -+ 0xff, -+ op->dummy.nbytes); -+ -+ if (op->data.nbytes && op->data.dir == SPI_MEM_DATA_OUT) -+ memcpy(tx_tmp_buf + op->dummy.nbytes + op->addr.nbytes + 1, -+ op->data.buf.out, -+ op->data.nbytes); -+ -+ mdata->tx_dma = dma_map_single(mdata->dev, tx_tmp_buf, -+ tx_size, DMA_TO_DEVICE); -+ if (dma_mapping_error(mdata->dev, mdata->tx_dma)) { -+ ret = -ENOMEM; -+ goto err_exit; -+ } -+ -+ if (op->data.dir == SPI_MEM_DATA_IN) { -+ if (!IS_ALIGNED((size_t)op->data.buf.in, 4)) { -+ rx_tmp_buf = kzalloc(op->data.nbytes, -+ GFP_KERNEL | GFP_DMA); -+ if (!rx_tmp_buf) { -+ ret = -ENOMEM; -+ goto unmap_tx_dma; -+ } -+ } else { -+ rx_tmp_buf = op->data.buf.in; -+ } -+ -+ mdata->rx_dma = dma_map_single(mdata->dev, -+ rx_tmp_buf, -+ op->data.nbytes, -+ DMA_FROM_DEVICE); -+ if (dma_mapping_error(mdata->dev, mdata->rx_dma)) { -+ ret = -ENOMEM; -+ goto kfree_rx_tmp_buf; -+ } -+ } -+ -+ reg_val = readl(mdata->base + SPI_CMD_REG); -+ reg_val |= SPI_CMD_TX_DMA; -+ if (op->data.dir == SPI_MEM_DATA_IN) -+ reg_val |= SPI_CMD_RX_DMA; -+ writel(reg_val, mdata->base + SPI_CMD_REG); -+ -+ mtk_spi_mem_setup_dma_xfer(mem->spi->master, op); -+ -+ mtk_spi_enable_transfer(mem->spi->master); -+ -+ /* Wait for the interrupt. */ -+ ret = mtk_spi_transfer_wait(mem, op); -+ if (ret) -+ goto unmap_rx_dma; -+ -+ /* spi disable dma */ -+ reg_val = readl(mdata->base + SPI_CMD_REG); -+ reg_val &= ~SPI_CMD_TX_DMA; -+ if (op->data.dir == SPI_MEM_DATA_IN) -+ reg_val &= ~SPI_CMD_RX_DMA; -+ writel(reg_val, mdata->base + SPI_CMD_REG); -+ -+unmap_rx_dma: -+ if (op->data.dir == SPI_MEM_DATA_IN) { -+ dma_unmap_single(mdata->dev, mdata->rx_dma, -+ op->data.nbytes, DMA_FROM_DEVICE); -+ if (!IS_ALIGNED((size_t)op->data.buf.in, 4)) -+ memcpy(op->data.buf.in, rx_tmp_buf, op->data.nbytes); -+ } -+kfree_rx_tmp_buf: -+ if (op->data.dir == SPI_MEM_DATA_IN && -+ !IS_ALIGNED((size_t)op->data.buf.in, 4)) -+ kfree(rx_tmp_buf); -+unmap_tx_dma: -+ dma_unmap_single(mdata->dev, mdata->tx_dma, -+ tx_size, DMA_TO_DEVICE); -+err_exit: -+ kfree(tx_tmp_buf); -+ mdata->use_spimem = false; -+ -+ return ret; -+} -+ -+static const struct spi_controller_mem_ops mtk_spi_mem_ops = { -+ .adjust_op_size = mtk_spi_mem_adjust_op_size, -+ .supports_op = mtk_spi_mem_supports_op, -+ .exec_op = mtk_spi_mem_exec_op, -+}; -+ - static int mtk_spi_probe(struct platform_device *pdev) - { - struct spi_master *master; -@@ -739,6 +1103,7 @@ static int mtk_spi_probe(struct platform - master->can_dma = mtk_spi_can_dma; - master->setup = mtk_spi_setup; - master->set_cs_timing = mtk_spi_set_hw_cs_timing; -+ master->use_gpio_descriptors = true; - - of_id = of_match_node(mtk_spi_of_match, pdev->dev.of_node); - if (!of_id) { -@@ -755,6 +1120,14 @@ static int mtk_spi_probe(struct platform - - if (mdata->dev_comp->must_tx) - master->flags = SPI_MASTER_MUST_TX; -+ if (mdata->dev_comp->ipm_design) -+ master->mode_bits |= SPI_LOOP; -+ -+ if (mdata->dev_comp->ipm_design) { -+ mdata->dev = &pdev->dev; -+ master->mem_ops = &mtk_spi_mem_ops; -+ init_completion(&mdata->spimem_done); -+ } - - if (mdata->dev_comp->need_pad_sel) { - mdata->pad_num = of_property_count_u32_elems( -@@ -831,25 +1204,40 @@ static int mtk_spi_probe(struct platform - goto err_put_master; - } - -+ mdata->spi_hclk = devm_clk_get_optional(&pdev->dev, "hclk"); -+ if (IS_ERR(mdata->spi_hclk)) { -+ ret = PTR_ERR(mdata->spi_hclk); -+ dev_err(&pdev->dev, "failed to get hclk: %d\n", ret); -+ goto err_put_master; -+ } -+ -+ ret = clk_prepare_enable(mdata->spi_hclk); -+ if (ret < 0) { -+ dev_err(&pdev->dev, "failed to enable hclk (%d)\n", ret); -+ goto err_put_master; -+ } -+ - ret = clk_prepare_enable(mdata->spi_clk); - if (ret < 0) { - dev_err(&pdev->dev, "failed to enable spi_clk (%d)\n", ret); -- goto err_put_master; -+ goto err_disable_spi_hclk; - } - - ret = clk_set_parent(mdata->sel_clk, mdata->parent_clk); - if (ret < 0) { - dev_err(&pdev->dev, "failed to clk_set_parent (%d)\n", ret); -- clk_disable_unprepare(mdata->spi_clk); -- goto err_put_master; -+ goto err_disable_spi_clk; - } - - mdata->spi_clk_hz = clk_get_rate(mdata->spi_clk); - -- if (mdata->dev_comp->no_need_unprepare) -+ if (mdata->dev_comp->no_need_unprepare) { - clk_disable(mdata->spi_clk); -- else -+ clk_disable(mdata->spi_hclk); -+ } else { - clk_disable_unprepare(mdata->spi_clk); -+ clk_disable_unprepare(mdata->spi_hclk); -+ } - - pm_runtime_enable(&pdev->dev); - -@@ -862,25 +1250,12 @@ static int mtk_spi_probe(struct platform - goto err_disable_runtime_pm; - } - -- if (!master->cs_gpios && master->num_chipselect > 1) { -+ if (!master->cs_gpiods && master->num_chipselect > 1) { - dev_err(&pdev->dev, - "cs_gpios not specified and num_chipselect > 1\n"); - ret = -EINVAL; - goto err_disable_runtime_pm; - } -- -- if (master->cs_gpios) { -- for (i = 0; i < master->num_chipselect; i++) { -- ret = devm_gpio_request(&pdev->dev, -- master->cs_gpios[i], -- dev_name(&pdev->dev)); -- if (ret) { -- dev_err(&pdev->dev, -- "can't get CS GPIO %i\n", i); -- goto err_disable_runtime_pm; -- } -- } -- } - } - - if (mdata->dev_comp->dma_ext) -@@ -902,6 +1277,10 @@ static int mtk_spi_probe(struct platform - - err_disable_runtime_pm: - pm_runtime_disable(&pdev->dev); -+err_disable_spi_clk: -+ clk_disable_unprepare(mdata->spi_clk); -+err_disable_spi_hclk: -+ clk_disable_unprepare(mdata->spi_hclk); - err_put_master: - spi_master_put(master); - -@@ -920,8 +1299,10 @@ static int mtk_spi_remove(struct platfor - - mtk_spi_reset(mdata); - -- if (mdata->dev_comp->no_need_unprepare) -+ if (mdata->dev_comp->no_need_unprepare) { - clk_unprepare(mdata->spi_clk); -+ clk_unprepare(mdata->spi_hclk); -+ } - - pm_runtime_put_noidle(&pdev->dev); - pm_runtime_disable(&pdev->dev); -@@ -940,8 +1321,10 @@ static int mtk_spi_suspend(struct device - if (ret) - return ret; - -- if (!pm_runtime_suspended(dev)) -+ if (!pm_runtime_suspended(dev)) { - clk_disable_unprepare(mdata->spi_clk); -+ clk_disable_unprepare(mdata->spi_hclk); -+ } - - return ret; - } -@@ -958,11 +1341,20 @@ static int mtk_spi_resume(struct device - dev_err(dev, "failed to enable spi_clk (%d)\n", ret); - return ret; - } -+ -+ ret = clk_prepare_enable(mdata->spi_hclk); -+ if (ret < 0) { -+ dev_err(dev, "failed to enable spi_hclk (%d)\n", ret); -+ clk_disable_unprepare(mdata->spi_clk); -+ return ret; -+ } - } - - ret = spi_master_resume(master); -- if (ret < 0) -+ if (ret < 0) { - clk_disable_unprepare(mdata->spi_clk); -+ clk_disable_unprepare(mdata->spi_hclk); -+ } - - return ret; - } -@@ -974,10 +1366,13 @@ static int mtk_spi_runtime_suspend(struc - struct spi_master *master = dev_get_drvdata(dev); - struct mtk_spi *mdata = spi_master_get_devdata(master); - -- if (mdata->dev_comp->no_need_unprepare) -+ if (mdata->dev_comp->no_need_unprepare) { - clk_disable(mdata->spi_clk); -- else -+ clk_disable(mdata->spi_hclk); -+ } else { - clk_disable_unprepare(mdata->spi_clk); -+ clk_disable_unprepare(mdata->spi_hclk); -+ } - - return 0; - } -@@ -988,13 +1383,31 @@ static int mtk_spi_runtime_resume(struct - struct mtk_spi *mdata = spi_master_get_devdata(master); - int ret; - -- if (mdata->dev_comp->no_need_unprepare) -+ if (mdata->dev_comp->no_need_unprepare) { - ret = clk_enable(mdata->spi_clk); -- else -+ if (ret < 0) { -+ dev_err(dev, "failed to enable spi_clk (%d)\n", ret); -+ return ret; -+ } -+ ret = clk_enable(mdata->spi_hclk); -+ if (ret < 0) { -+ dev_err(dev, "failed to enable spi_hclk (%d)\n", ret); -+ clk_disable(mdata->spi_clk); -+ return ret; -+ } -+ } else { - ret = clk_prepare_enable(mdata->spi_clk); -- if (ret < 0) { -- dev_err(dev, "failed to enable spi_clk (%d)\n", ret); -- return ret; -+ if (ret < 0) { -+ dev_err(dev, "failed to prepare_enable spi_clk (%d)\n", ret); -+ return ret; -+ } -+ -+ ret = clk_prepare_enable(mdata->spi_hclk); -+ if (ret < 0) { -+ dev_err(dev, "failed to prepare_enable spi_hclk (%d)\n", ret); -+ clk_disable_unprepare(mdata->spi_clk); -+ return ret; -+ } - } - - return 0; diff --git a/target/linux/mediatek/patches-5.15/214-v6.3-clk-mediatek-add-mt7981-clock-support.patch b/target/linux/mediatek/patches-5.15/214-v6.3-clk-mediatek-add-mt7981-clock-support.patch deleted file mode 100644 index 631eb04092..0000000000 --- a/target/linux/mediatek/patches-5.15/214-v6.3-clk-mediatek-add-mt7981-clock-support.patch +++ /dev/null @@ -1,39 +0,0 @@ ---- a/drivers/clk/mediatek/Kconfig -+++ b/drivers/clk/mediatek/Kconfig -@@ -344,6 +344,23 @@ config COMMON_CLK_MT7629_HIFSYS - This driver supports MediaTek MT7629 HIFSYS clocks providing - to PCI-E and USB. - -+config COMMON_CLK_MT7981 -+ bool "Clock driver for MediaTek MT7981" -+ depends on ARCH_MEDIATEK || COMPILE_TEST -+ select COMMON_CLK_MEDIATEK -+ default ARCH_MEDIATEK -+ help -+ This driver supports MediaTek MT7981 basic clocks and clocks -+ required for various periperals found on MediaTek. -+ -+config COMMON_CLK_MT7981_ETHSYS -+ bool "Clock driver for MediaTek MT7981 ETHSYS" -+ depends on COMMON_CLK_MT7981 -+ default COMMON_CLK_MT7981 -+ help -+ This driver add support for clocks for Ethernet and SGMII -+ required on MediaTek MT7981 SoC. -+ - config COMMON_CLK_MT7986 - bool "Clock driver for MediaTek MT7986" - depends on ARCH_MEDIATEK || COMPILE_TEST ---- a/drivers/clk/mediatek/Makefile -+++ b/drivers/clk/mediatek/Makefile -@@ -46,6 +46,10 @@ obj-$(CONFIG_COMMON_CLK_MT7622_AUDSYS) + - obj-$(CONFIG_COMMON_CLK_MT7629) += clk-mt7629.o - obj-$(CONFIG_COMMON_CLK_MT7629_ETHSYS) += clk-mt7629-eth.o - obj-$(CONFIG_COMMON_CLK_MT7629_HIFSYS) += clk-mt7629-hif.o -+obj-$(CONFIG_COMMON_CLK_MT7981) += clk-mt7981-apmixed.o -+obj-$(CONFIG_COMMON_CLK_MT7981) += clk-mt7981-topckgen.o -+obj-$(CONFIG_COMMON_CLK_MT7981) += clk-mt7981-infracfg.o -+obj-$(CONFIG_COMMON_CLK_MT7981_ETHSYS) += clk-mt7981-eth.o - obj-$(CONFIG_COMMON_CLK_MT7986) += clk-mt7986-apmixed.o - obj-$(CONFIG_COMMON_CLK_MT7986) += clk-mt7986-topckgen.o - obj-$(CONFIG_COMMON_CLK_MT7986) += clk-mt7986-infracfg.o diff --git a/target/linux/mediatek/patches-5.15/215-v6.3-pinctrl-mediatek-add-support-for-MT7981-SoC.patch b/target/linux/mediatek/patches-5.15/215-v6.3-pinctrl-mediatek-add-support-for-MT7981-SoC.patch deleted file mode 100644 index ae99685df4..0000000000 --- a/target/linux/mediatek/patches-5.15/215-v6.3-pinctrl-mediatek-add-support-for-MT7981-SoC.patch +++ /dev/null @@ -1,26 +0,0 @@ ---- a/drivers/pinctrl/mediatek/Kconfig -+++ b/drivers/pinctrl/mediatek/Kconfig -@@ -120,6 +120,13 @@ config PINCTRL_MT7622 - default ARM64 && ARCH_MEDIATEK - select PINCTRL_MTK_MOORE - -+config PINCTRL_MT7981 -+ bool "Mediatek MT7981 pin control" -+ depends on OF -+ depends on ARM64 || COMPILE_TEST -+ default ARM64 && ARCH_MEDIATEK -+ select PINCTRL_MTK_MOORE -+ - config PINCTRL_MT7986 - bool "Mediatek MT7986 pin control" - depends on OF ---- a/drivers/pinctrl/mediatek/Makefile -+++ b/drivers/pinctrl/mediatek/Makefile -@@ -17,6 +17,7 @@ obj-$(CONFIG_PINCTRL_MT6797) += pinctrl- - obj-$(CONFIG_PINCTRL_MT7622) += pinctrl-mt7622.o - obj-$(CONFIG_PINCTRL_MT7623) += pinctrl-mt7623.o - obj-$(CONFIG_PINCTRL_MT7629) += pinctrl-mt7629.o -+obj-$(CONFIG_PINCTRL_MT7986) += pinctrl-mt7981.o - obj-$(CONFIG_PINCTRL_MT7986) += pinctrl-mt7986.o - obj-$(CONFIG_PINCTRL_MT8167) += pinctrl-mt8167.o - obj-$(CONFIG_PINCTRL_MT8173) += pinctrl-mt8173.o diff --git a/target/linux/mediatek/patches-5.15/240-pinctrl-mediatek-add-support-for-MT7988-SoC.patch b/target/linux/mediatek/patches-5.15/240-pinctrl-mediatek-add-support-for-MT7988-SoC.patch deleted file mode 100644 index cbee45bc1f..0000000000 --- a/target/linux/mediatek/patches-5.15/240-pinctrl-mediatek-add-support-for-MT7988-SoC.patch +++ /dev/null @@ -1,26 +0,0 @@ ---- a/drivers/pinctrl/mediatek/Kconfig -+++ b/drivers/pinctrl/mediatek/Kconfig -@@ -134,6 +134,13 @@ config PINCTRL_MT7986 - default ARM64 && ARCH_MEDIATEK - select PINCTRL_MTK_MOORE - -+config PINCTRL_MT7988 -+ bool "Mediatek MT7988 pin control" -+ depends on OF -+ depends on ARM64 || COMPILE_TEST -+ default ARCH_MEDIATEK -+ select PINCTRL_MTK_MOORE -+ - config PINCTRL_MT8167 - bool "Mediatek MT8167 pin control" - depends on OF ---- a/drivers/pinctrl/mediatek/Makefile -+++ b/drivers/pinctrl/mediatek/Makefile -@@ -19,6 +19,7 @@ obj-$(CONFIG_PINCTRL_MT7623) += pinctrl- - obj-$(CONFIG_PINCTRL_MT7629) += pinctrl-mt7629.o - obj-$(CONFIG_PINCTRL_MT7986) += pinctrl-mt7981.o - obj-$(CONFIG_PINCTRL_MT7986) += pinctrl-mt7986.o -+obj-$(CONFIG_PINCTRL_MT7988) += pinctrl-mt7988.o - obj-$(CONFIG_PINCTRL_MT8167) += pinctrl-mt8167.o - obj-$(CONFIG_PINCTRL_MT8173) += pinctrl-mt8173.o - obj-$(CONFIG_PINCTRL_MT8183) += pinctrl-mt8183.o diff --git a/target/linux/mediatek/patches-5.15/241-clk-mediatek-Add-pcw-chg-shift-control.patch b/target/linux/mediatek/patches-5.15/241-clk-mediatek-Add-pcw-chg-shift-control.patch deleted file mode 100644 index 23a5b7c911..0000000000 --- a/target/linux/mediatek/patches-5.15/241-clk-mediatek-Add-pcw-chg-shift-control.patch +++ /dev/null @@ -1,24 +0,0 @@ ---- a/drivers/clk/mediatek/clk-mtk.h -+++ b/drivers/clk/mediatek/clk-mtk.h -@@ -233,6 +233,7 @@ struct mtk_pll_data { - u32 pcw_reg; - int pcw_shift; - u32 pcw_chg_reg; -+ int pcw_chg_shift; - const struct mtk_pll_div_table *div_table; - const char *parent_name; - u32 en_reg; ---- a/drivers/clk/mediatek/clk-pll.c -+++ b/drivers/clk/mediatek/clk-pll.c -@@ -137,7 +137,10 @@ static void mtk_pll_set_rate_regs(struct - pll->data->pcw_shift); - val |= pcw << pll->data->pcw_shift; - writel(val, pll->pcw_addr); -- chg = readl(pll->pcw_chg_addr) | PCW_CHG_MASK; -+ if (pll->data->pcw_chg_shift) -+ chg = readl(pll->pcw_chg_addr) | BIT(pll->data->pcw_chg_shift); -+ else -+ chg = readl(pll->pcw_chg_addr) | PCW_CHG_MASK; - writel(chg, pll->pcw_chg_addr); - if (pll->tuner_addr) - writel(val + 1, pll->tuner_addr); diff --git a/target/linux/mediatek/patches-5.15/242-clk-mediatek-add-mt7988-clock-support.patch b/target/linux/mediatek/patches-5.15/242-clk-mediatek-add-mt7988-clock-support.patch deleted file mode 100644 index bf9146352a..0000000000 --- a/target/linux/mediatek/patches-5.15/242-clk-mediatek-add-mt7988-clock-support.patch +++ /dev/null @@ -1,31 +0,0 @@ ---- a/drivers/clk/mediatek/Kconfig -+++ b/drivers/clk/mediatek/Kconfig -@@ -378,6 +378,15 @@ config COMMON_CLK_MT7986_ETHSYS - This driver add support for clocks for Ethernet and SGMII - required on MediaTek MT7986 SoC. - -+config COMMON_CLK_MT7988 -+ bool "Clock driver for MediaTek MT7988" -+ depends on ARCH_MEDIATEK || COMPILE_TEST -+ select COMMON_CLK_MEDIATEK -+ default ARCH_MEDIATEK -+ help -+ This driver supports MediaTek MT7988 basic clocks and clocks -+ required for various periperals found on MediaTek. -+ - config COMMON_CLK_MT8135 - bool "Clock driver for MediaTek MT8135" - depends on (ARCH_MEDIATEK && ARM) || COMPILE_TEST ---- a/drivers/clk/mediatek/Makefile -+++ b/drivers/clk/mediatek/Makefile -@@ -54,6 +54,10 @@ obj-$(CONFIG_COMMON_CLK_MT7986) += clk-m - obj-$(CONFIG_COMMON_CLK_MT7986) += clk-mt7986-topckgen.o - obj-$(CONFIG_COMMON_CLK_MT7986) += clk-mt7986-infracfg.o - obj-$(CONFIG_COMMON_CLK_MT7986_ETHSYS) += clk-mt7986-eth.o -+obj-$(CONFIG_COMMON_CLK_MT7988) += clk-mt7988-apmixed.o -+obj-$(CONFIG_COMMON_CLK_MT7988) += clk-mt7988-topckgen.o -+obj-$(CONFIG_COMMON_CLK_MT7988) += clk-mt7988-infracfg.o -+obj-$(CONFIG_COMMON_CLK_MT7988) += clk-mt7988-eth.o - obj-$(CONFIG_COMMON_CLK_MT8135) += clk-mt8135.o - obj-$(CONFIG_COMMON_CLK_MT8167) += clk-mt8167.o - obj-$(CONFIG_COMMON_CLK_MT8167_AUDSYS) += clk-mt8167-aud.o diff --git a/target/linux/mediatek/patches-5.15/320-mmc-mediatek-add-support-for-MT7986-SoC.patch b/target/linux/mediatek/patches-5.15/320-mmc-mediatek-add-support-for-MT7986-SoC.patch deleted file mode 100644 index 56ffa73c00..0000000000 --- a/target/linux/mediatek/patches-5.15/320-mmc-mediatek-add-support-for-MT7986-SoC.patch +++ /dev/null @@ -1,44 +0,0 @@ -From 1a7963e9843f6f1e4b02a30926d20b314c03e4df Mon Sep 17 00:00:00 2001 -From: Sam Shih -Date: Sat, 25 Jun 2022 02:10:13 +0800 -Subject: [PATCH] mmc: mediatek: add support for MT7986 SoC - -Adding mt7986 own characteristics and of_device_id to have support -of MT7986 SoC. - -Signed-off-by: Sam Shih -Change-Id: I07cf8406cbe8c1a7114b304f35fc3e689e512e5a ---- - drivers/mmc/host/mtk-sd.c | 14 ++++++++++++++ - 1 file changed, 14 insertions(+) - ---- a/drivers/mmc/host/mtk-sd.c -+++ b/drivers/mmc/host/mtk-sd.c -@@ -540,6 +540,19 @@ static const struct mtk_mmc_compatible m - .support_64g = false, - }; - -+static const struct mtk_mmc_compatible mt7986_compat = { -+ .clk_div_bits = 12, -+ .recheck_sdio_irq = true, -+ .hs400_tune = false, -+ .pad_tune_reg = MSDC_PAD_TUNE0, -+ .async_fifo = true, -+ .data_tune = true, -+ .busy_check = true, -+ .stop_clk_fix = true, -+ .enhance_rx = true, -+ .support_64g = true, -+}; -+ - static const struct mtk_mmc_compatible mt8516_compat = { - .clk_div_bits = 12, - .recheck_sdio_irq = true, -@@ -584,6 +597,7 @@ static const struct of_device_id msdc_of - { .compatible = "mediatek,mt2701-mmc", .data = &mt2701_compat}, - { .compatible = "mediatek,mt2712-mmc", .data = &mt2712_compat}, - { .compatible = "mediatek,mt7622-mmc", .data = &mt7622_compat}, -+ { .compatible = "mediatek,mt7986-mmc", .data = &mt7986_compat}, - { .compatible = "mediatek,mt8516-mmc", .data = &mt8516_compat}, - { .compatible = "mediatek,mt7620-mmc", .data = &mt7620_compat}, - { .compatible = "mediatek,mt6779-mmc", .data = &mt6779_compat}, diff --git a/target/linux/mediatek/patches-5.15/330-snand-mtk-bmt-support.patch b/target/linux/mediatek/patches-5.15/330-snand-mtk-bmt-support.patch deleted file mode 100644 index 6814e5f5e9..0000000000 --- a/target/linux/mediatek/patches-5.15/330-snand-mtk-bmt-support.patch +++ /dev/null @@ -1,34 +0,0 @@ ---- a/drivers/mtd/nand/spi/core.c -+++ b/drivers/mtd/nand/spi/core.c -@@ -19,6 +19,7 @@ - #include - #include - #include -+#include - - static int spinand_read_reg_op(struct spinand_device *spinand, u8 reg, u8 *val) - { -@@ -1343,6 +1344,7 @@ static int spinand_probe(struct spi_mem - if (ret) - return ret; - -+ mtk_bmt_attach(mtd); - ret = mtd_device_register(mtd, NULL, 0); - if (ret) - goto err_spinand_cleanup; -@@ -1350,6 +1352,7 @@ static int spinand_probe(struct spi_mem - return 0; - - err_spinand_cleanup: -+ mtk_bmt_detach(mtd); - spinand_cleanup(spinand); - - return ret; -@@ -1368,6 +1371,7 @@ static int spinand_remove(struct spi_mem - if (ret) - return ret; - -+ mtk_bmt_detach(mtd); - spinand_cleanup(spinand); - - return 0; diff --git a/target/linux/mediatek/patches-5.15/331-mt7622-rfb1-enable-bmt.patch b/target/linux/mediatek/patches-5.15/331-mt7622-rfb1-enable-bmt.patch deleted file mode 100644 index 9c1a8f284a..0000000000 --- a/target/linux/mediatek/patches-5.15/331-mt7622-rfb1-enable-bmt.patch +++ /dev/null @@ -1,10 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts -+++ b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts -@@ -553,6 +553,7 @@ - spi-tx-bus-width = <4>; - spi-rx-bus-width = <4>; - nand-ecc-engine = <&snfi>; -+ mediatek,bmt-v2; - - partitions { - compatible = "fixed-partitions"; diff --git a/target/linux/mediatek/patches-5.15/340-mtd-spinand-Add-support-for-the-Fidelix-FM35X1GA.patch b/target/linux/mediatek/patches-5.15/340-mtd-spinand-Add-support-for-the-Fidelix-FM35X1GA.patch deleted file mode 100644 index 6baa32879b..0000000000 --- a/target/linux/mediatek/patches-5.15/340-mtd-spinand-Add-support-for-the-Fidelix-FM35X1GA.patch +++ /dev/null @@ -1,122 +0,0 @@ -From 5f49a5c9b16330e0df8f639310e4715dcad71947 Mon Sep 17 00:00:00 2001 -From: Davide Fioravanti -Date: Fri, 8 Jan 2021 15:35:24 +0100 -Subject: [PATCH] mtd: spinand: Add support for the Fidelix FM35X1GA - -Datasheet: http://www.hobos.com.cn/upload/datasheet/DS35X1GAXXX_100_rev00.pdf - -Signed-off-by: Davide Fioravanti ---- - drivers/mtd/nand/spi/Makefile | 2 +- - drivers/mtd/nand/spi/core.c | 1 + - drivers/mtd/nand/spi/fidelix.c | 76 ++++++++++++++++++++++++++++++++++ - include/linux/mtd/spinand.h | 1 + - 4 files changed, 79 insertions(+), 1 deletion(-) - create mode 100644 drivers/mtd/nand/spi/fidelix.c - ---- a/drivers/mtd/nand/spi/Makefile -+++ b/drivers/mtd/nand/spi/Makefile -@@ -1,3 +1,3 @@ - # SPDX-License-Identifier: GPL-2.0 --spinand-objs := core.o esmt.o etron.o gigadevice.o macronix.o micron.o paragon.o toshiba.o winbond.o xtx.o -+spinand-objs := core.o esmt.o etron.o fidelix.o gigadevice.o macronix.o micron.o paragon.o toshiba.o winbond.o xtx.o - obj-$(CONFIG_MTD_SPI_NAND) += spinand.o ---- a/drivers/mtd/nand/spi/core.c -+++ b/drivers/mtd/nand/spi/core.c -@@ -939,6 +939,7 @@ static const struct nand_ops spinand_ops - - static const struct spinand_manufacturer *spinand_manufacturers[] = { - &esmt_c8_spinand_manufacturer, -+ &fidelix_spinand_manufacturer, - &gigadevice_spinand_manufacturer, - &etron_spinand_manufacturer, - ¯onix_spinand_manufacturer, ---- /dev/null -+++ b/drivers/mtd/nand/spi/fidelix.c -@@ -0,0 +1,76 @@ -+// SPDX-License-Identifier: GPL-2.0 -+/* -+ * Copyright (c) 2020 Davide Fioravanti -+ */ -+ -+#include -+#include -+#include -+ -+#define SPINAND_MFR_FIDELIX 0xE5 -+#define FIDELIX_ECCSR_MASK 0x0F -+ -+static SPINAND_OP_VARIANTS(read_cache_variants, -+ SPINAND_PAGE_READ_FROM_CACHE_X4_OP(0, 1, NULL, 0), -+ SPINAND_PAGE_READ_FROM_CACHE_OP(true, 0, 1, NULL, 0), -+ SPINAND_PAGE_READ_FROM_CACHE_OP(false, 0, 1, NULL, 0)); -+ -+static SPINAND_OP_VARIANTS(write_cache_variants, -+ SPINAND_PROG_LOAD_X4(true, 0, NULL, 0), -+ SPINAND_PROG_LOAD(true, 0, NULL, 0)); -+ -+static SPINAND_OP_VARIANTS(update_cache_variants, -+ SPINAND_PROG_LOAD_X4(false, 0, NULL, 0), -+ SPINAND_PROG_LOAD(false, 0, NULL, 0)); -+ -+static int fm35x1ga_ooblayout_ecc(struct mtd_info *mtd, int section, -+ struct mtd_oob_region *region) -+{ -+ if (section > 3) -+ return -ERANGE; -+ -+ region->offset = (16 * section) + 8; -+ region->length = 8; -+ -+ return 0; -+} -+ -+static int fm35x1ga_ooblayout_free(struct mtd_info *mtd, int section, -+ struct mtd_oob_region *region) -+{ -+ if (section > 3) -+ return -ERANGE; -+ -+ region->offset = (16 * section) + 2; -+ region->length = 6; -+ -+ return 0; -+} -+ -+static const struct mtd_ooblayout_ops fm35x1ga_ooblayout = { -+ .ecc = fm35x1ga_ooblayout_ecc, -+ .free = fm35x1ga_ooblayout_free, -+}; -+ -+static const struct spinand_info fidelix_spinand_table[] = { -+ SPINAND_INFO("FM35X1GA", -+ SPINAND_ID(SPINAND_READID_METHOD_OPCODE_DUMMY, 0x71), -+ NAND_MEMORG(1, 2048, 64, 64, 1024, 20, 1, 1, 1), -+ NAND_ECCREQ(4, 512), -+ SPINAND_INFO_OP_VARIANTS(&read_cache_variants, -+ &write_cache_variants, -+ &update_cache_variants), -+ SPINAND_HAS_QE_BIT, -+ SPINAND_ECCINFO(&fm35x1ga_ooblayout, NULL)), -+}; -+ -+static const struct spinand_manufacturer_ops fidelix_spinand_manuf_ops = { -+}; -+ -+const struct spinand_manufacturer fidelix_spinand_manufacturer = { -+ .id = SPINAND_MFR_FIDELIX, -+ .name = "Fidelix", -+ .chips = fidelix_spinand_table, -+ .nchips = ARRAY_SIZE(fidelix_spinand_table), -+ .ops = &fidelix_spinand_manuf_ops, -+}; ---- a/include/linux/mtd/spinand.h -+++ b/include/linux/mtd/spinand.h -@@ -262,6 +262,7 @@ struct spinand_manufacturer { - /* SPI NAND manufacturers */ - extern const struct spinand_manufacturer esmt_c8_spinand_manufacturer; - extern const struct spinand_manufacturer etron_spinand_manufacturer; -+extern const struct spinand_manufacturer fidelix_spinand_manufacturer; - extern const struct spinand_manufacturer gigadevice_spinand_manufacturer; - extern const struct spinand_manufacturer macronix_spinand_manufacturer; - extern const struct spinand_manufacturer micron_spinand_manufacturer; diff --git a/target/linux/mediatek/patches-5.15/350-01-cpufreq-mediatek-Cleanup-variables-and-error-handlin.patch b/target/linux/mediatek/patches-5.15/350-01-cpufreq-mediatek-Cleanup-variables-and-error-handlin.patch deleted file mode 100644 index 8fad64a570..0000000000 --- a/target/linux/mediatek/patches-5.15/350-01-cpufreq-mediatek-Cleanup-variables-and-error-handlin.patch +++ /dev/null @@ -1,166 +0,0 @@ -From 7a768326fdba542144833b9198a6d0edab52fad2 Mon Sep 17 00:00:00 2001 -From: Jia-Wei Chang -Date: Fri, 8 Apr 2022 12:58:56 +0800 -Subject: [PATCH 01/21] cpufreq: mediatek: Cleanup variables and error handling - in mtk_cpu_dvfs_info_init() - -- Remove several unnecessary varaibles in mtk_cpu_dvfs_info_init(). -- Unify error message format and use dev_err_probe() if possible. - -Signed-off-by: Jia-Wei Chang -Signed-off-by: Rex-BC Chen -Reviewed-by: AngeloGioacchino Del Regno -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 89 ++++++++++++------------------ - 1 file changed, 34 insertions(+), 55 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -302,96 +302,75 @@ static int mtk_cpufreq_set_target(struct - static int mtk_cpu_dvfs_info_init(struct mtk_cpu_dvfs_info *info, int cpu) - { - struct device *cpu_dev; -- struct regulator *proc_reg = ERR_PTR(-ENODEV); -- struct regulator *sram_reg = ERR_PTR(-ENODEV); -- struct clk *cpu_clk = ERR_PTR(-ENODEV); -- struct clk *inter_clk = ERR_PTR(-ENODEV); - struct dev_pm_opp *opp; - unsigned long rate; - int ret; - - cpu_dev = get_cpu_device(cpu); - if (!cpu_dev) { -- pr_err("failed to get cpu%d device\n", cpu); -+ dev_err(cpu_dev, "failed to get cpu%d device\n", cpu); - return -ENODEV; - } -+ info->cpu_dev = cpu_dev; - -- cpu_clk = clk_get(cpu_dev, "cpu"); -- if (IS_ERR(cpu_clk)) { -- if (PTR_ERR(cpu_clk) == -EPROBE_DEFER) -- pr_warn("cpu clk for cpu%d not ready, retry.\n", cpu); -- else -- pr_err("failed to get cpu clk for cpu%d\n", cpu); -- -- ret = PTR_ERR(cpu_clk); -- return ret; -- } -- -- inter_clk = clk_get(cpu_dev, "intermediate"); -- if (IS_ERR(inter_clk)) { -- if (PTR_ERR(inter_clk) == -EPROBE_DEFER) -- pr_warn("intermediate clk for cpu%d not ready, retry.\n", -- cpu); -- else -- pr_err("failed to get intermediate clk for cpu%d\n", -- cpu); -+ info->cpu_clk = clk_get(cpu_dev, "cpu"); -+ if (IS_ERR(info->cpu_clk)) { -+ ret = PTR_ERR(info->cpu_clk); -+ return dev_err_probe(cpu_dev, ret, -+ "cpu%d: failed to get cpu clk\n", cpu); -+ } - -- ret = PTR_ERR(inter_clk); -+ info->inter_clk = clk_get(cpu_dev, "intermediate"); -+ if (IS_ERR(info->inter_clk)) { -+ ret = PTR_ERR(info->inter_clk); -+ dev_err_probe(cpu_dev, ret, -+ "cpu%d: failed to get intermediate clk\n", cpu); - goto out_free_resources; - } - -- proc_reg = regulator_get_optional(cpu_dev, "proc"); -- if (IS_ERR(proc_reg)) { -- if (PTR_ERR(proc_reg) == -EPROBE_DEFER) -- pr_warn("proc regulator for cpu%d not ready, retry.\n", -- cpu); -- else -- pr_err("failed to get proc regulator for cpu%d\n", -- cpu); -- -- ret = PTR_ERR(proc_reg); -+ info->proc_reg = regulator_get_optional(cpu_dev, "proc"); -+ if (IS_ERR(info->proc_reg)) { -+ ret = PTR_ERR(info->proc_reg); -+ dev_err_probe(cpu_dev, ret, -+ "cpu%d: failed to get proc regulator\n", cpu); - goto out_free_resources; - } - - /* Both presence and absence of sram regulator are valid cases. */ -- sram_reg = regulator_get_exclusive(cpu_dev, "sram"); -+ info->sram_reg = regulator_get_exclusive(cpu_dev, "sram"); -+ if (IS_ERR(info->sram_reg)) -+ info->sram_reg = NULL; - - /* Get OPP-sharing information from "operating-points-v2" bindings */ - ret = dev_pm_opp_of_get_sharing_cpus(cpu_dev, &info->cpus); - if (ret) { -- pr_err("failed to get OPP-sharing information for cpu%d\n", -- cpu); -+ dev_err(cpu_dev, -+ "cpu%d: failed to get OPP-sharing information\n", cpu); - goto out_free_resources; - } - - ret = dev_pm_opp_of_cpumask_add_table(&info->cpus); - if (ret) { -- pr_warn("no OPP table for cpu%d\n", cpu); -+ dev_warn(cpu_dev, "cpu%d: no OPP table\n", cpu); - goto out_free_resources; - } - - /* Search a safe voltage for intermediate frequency. */ -- rate = clk_get_rate(inter_clk); -+ rate = clk_get_rate(info->inter_clk); - opp = dev_pm_opp_find_freq_ceil(cpu_dev, &rate); - if (IS_ERR(opp)) { -- pr_err("failed to get intermediate opp for cpu%d\n", cpu); -+ dev_err(cpu_dev, "cpu%d: failed to get intermediate opp\n", cpu); - ret = PTR_ERR(opp); - goto out_free_opp_table; - } - info->intermediate_voltage = dev_pm_opp_get_voltage(opp); - dev_pm_opp_put(opp); - -- info->cpu_dev = cpu_dev; -- info->proc_reg = proc_reg; -- info->sram_reg = IS_ERR(sram_reg) ? NULL : sram_reg; -- info->cpu_clk = cpu_clk; -- info->inter_clk = inter_clk; -- - /* - * If SRAM regulator is present, software "voltage tracking" is needed - * for this CPU power domain. - */ -- info->need_voltage_tracking = !IS_ERR(sram_reg); -+ info->need_voltage_tracking = (info->sram_reg != NULL); - - return 0; - -@@ -399,14 +378,14 @@ out_free_opp_table: - dev_pm_opp_of_cpumask_remove_table(&info->cpus); - - out_free_resources: -- if (!IS_ERR(proc_reg)) -- regulator_put(proc_reg); -- if (!IS_ERR(sram_reg)) -- regulator_put(sram_reg); -- if (!IS_ERR(cpu_clk)) -- clk_put(cpu_clk); -- if (!IS_ERR(inter_clk)) -- clk_put(inter_clk); -+ if (!IS_ERR(info->proc_reg)) -+ regulator_put(info->proc_reg); -+ if (!IS_ERR(info->sram_reg)) -+ regulator_put(info->sram_reg); -+ if (!IS_ERR(info->cpu_clk)) -+ clk_put(info->cpu_clk); -+ if (!IS_ERR(info->inter_clk)) -+ clk_put(info->inter_clk); - - return ret; - } diff --git a/target/linux/mediatek/patches-5.15/350-02-cpufreq-mediatek-Remove-unused-headers.patch b/target/linux/mediatek/patches-5.15/350-02-cpufreq-mediatek-Remove-unused-headers.patch deleted file mode 100644 index eebeeb0902..0000000000 --- a/target/linux/mediatek/patches-5.15/350-02-cpufreq-mediatek-Remove-unused-headers.patch +++ /dev/null @@ -1,25 +0,0 @@ -From 756104b856d4bc3121420af3ced342f5fc2b2123 Mon Sep 17 00:00:00 2001 -From: Jia-Wei Chang -Date: Fri, 8 Apr 2022 12:58:57 +0800 -Subject: [PATCH 02/21] cpufreq: mediatek: Remove unused headers - -Remove unused headers. - -Signed-off-by: Jia-Wei Chang -Reviewed-by: AngeloGioacchino Del Regno -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 2 -- - 1 file changed, 2 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -13,8 +13,6 @@ - #include - #include - #include --#include --#include - - #define MIN_VOLT_SHIFT (100000) - #define MAX_VOLT_SHIFT (200000) diff --git a/target/linux/mediatek/patches-5.15/350-03-cpufreq-mediatek-Enable-clocks-and-regulators.patch b/target/linux/mediatek/patches-5.15/350-03-cpufreq-mediatek-Enable-clocks-and-regulators.patch deleted file mode 100644 index c97d5fc3d9..0000000000 --- a/target/linux/mediatek/patches-5.15/350-03-cpufreq-mediatek-Enable-clocks-and-regulators.patch +++ /dev/null @@ -1,117 +0,0 @@ -From 342d5545e9f40496db9ae0d31c2427dd5f369a43 Mon Sep 17 00:00:00 2001 -From: Jia-Wei Chang -Date: Fri, 8 Apr 2022 12:58:58 +0800 -Subject: [PATCH 03/21] cpufreq: mediatek: Enable clocks and regulators - -We need to enable regulators so that the max and min requested values will -be recorded. -The intermediate clock is not always enabled by CCF in different projects, -so we should enable it in the cpufreq driver. - -Signed-off-by: Andrew-sh.Cheng -Signed-off-by: Jia-Wei Chang -Signed-off-by: Rex-BC Chen -Reviewed-by: AngeloGioacchino Del Regno -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 50 +++++++++++++++++++++++++++--- - 1 file changed, 45 insertions(+), 5 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -334,10 +334,23 @@ static int mtk_cpu_dvfs_info_init(struct - goto out_free_resources; - } - -+ ret = regulator_enable(info->proc_reg); -+ if (ret) { -+ dev_warn(cpu_dev, "cpu%d: failed to enable vproc\n", cpu); -+ goto out_free_resources; -+ } -+ - /* Both presence and absence of sram regulator are valid cases. */ - info->sram_reg = regulator_get_exclusive(cpu_dev, "sram"); - if (IS_ERR(info->sram_reg)) - info->sram_reg = NULL; -+ else { -+ ret = regulator_enable(info->sram_reg); -+ if (ret) { -+ dev_warn(cpu_dev, "cpu%d: failed to enable vsram\n", cpu); -+ goto out_free_resources; -+ } -+ } - - /* Get OPP-sharing information from "operating-points-v2" bindings */ - ret = dev_pm_opp_of_get_sharing_cpus(cpu_dev, &info->cpus); -@@ -353,13 +366,21 @@ static int mtk_cpu_dvfs_info_init(struct - goto out_free_resources; - } - -+ ret = clk_prepare_enable(info->cpu_clk); -+ if (ret) -+ goto out_free_opp_table; -+ -+ ret = clk_prepare_enable(info->inter_clk); -+ if (ret) -+ goto out_disable_mux_clock; -+ - /* Search a safe voltage for intermediate frequency. */ - rate = clk_get_rate(info->inter_clk); - opp = dev_pm_opp_find_freq_ceil(cpu_dev, &rate); - if (IS_ERR(opp)) { - dev_err(cpu_dev, "cpu%d: failed to get intermediate opp\n", cpu); - ret = PTR_ERR(opp); -- goto out_free_opp_table; -+ goto out_disable_inter_clock; - } - info->intermediate_voltage = dev_pm_opp_get_voltage(opp); - dev_pm_opp_put(opp); -@@ -372,10 +393,21 @@ static int mtk_cpu_dvfs_info_init(struct - - return 0; - -+out_disable_inter_clock: -+ clk_disable_unprepare(info->inter_clk); -+ -+out_disable_mux_clock: -+ clk_disable_unprepare(info->cpu_clk); -+ - out_free_opp_table: - dev_pm_opp_of_cpumask_remove_table(&info->cpus); - - out_free_resources: -+ if (regulator_is_enabled(info->proc_reg)) -+ regulator_disable(info->proc_reg); -+ if (info->sram_reg && regulator_is_enabled(info->sram_reg)) -+ regulator_disable(info->sram_reg); -+ - if (!IS_ERR(info->proc_reg)) - regulator_put(info->proc_reg); - if (!IS_ERR(info->sram_reg)) -@@ -390,14 +422,22 @@ out_free_resources: - - static void mtk_cpu_dvfs_info_release(struct mtk_cpu_dvfs_info *info) - { -- if (!IS_ERR(info->proc_reg)) -+ if (!IS_ERR(info->proc_reg)) { -+ regulator_disable(info->proc_reg); - regulator_put(info->proc_reg); -- if (!IS_ERR(info->sram_reg)) -+ } -+ if (!IS_ERR(info->sram_reg)) { -+ regulator_disable(info->sram_reg); - regulator_put(info->sram_reg); -- if (!IS_ERR(info->cpu_clk)) -+ } -+ if (!IS_ERR(info->cpu_clk)) { -+ clk_disable_unprepare(info->cpu_clk); - clk_put(info->cpu_clk); -- if (!IS_ERR(info->inter_clk)) -+ } -+ if (!IS_ERR(info->inter_clk)) { -+ clk_disable_unprepare(info->inter_clk); - clk_put(info->inter_clk); -+ } - - dev_pm_opp_of_cpumask_remove_table(&info->cpus); - } diff --git a/target/linux/mediatek/patches-5.15/350-04-cpufreq-mediatek-Use-device-print-to-show-logs.patch b/target/linux/mediatek/patches-5.15/350-04-cpufreq-mediatek-Use-device-print-to-show-logs.patch deleted file mode 100644 index 18e1da728a..0000000000 --- a/target/linux/mediatek/patches-5.15/350-04-cpufreq-mediatek-Use-device-print-to-show-logs.patch +++ /dev/null @@ -1,161 +0,0 @@ -From a02e2b359141035d2d6999940bc1b9f83ec88587 Mon Sep 17 00:00:00 2001 -From: Rex-BC Chen -Date: Fri, 22 Apr 2022 15:52:27 +0800 -Subject: [PATCH 04/21] cpufreq: mediatek: Use device print to show logs - -- Replace pr_* with dev_* to show logs. -- Remove usage of __func__. - -Signed-off-by: Rex-BC Chen -Reviewed-by: AngeloGioacchino Del Regno -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 54 ++++++++++++++++-------------- - 1 file changed, 28 insertions(+), 26 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -67,7 +67,8 @@ static int mtk_cpufreq_voltage_tracking( - - old_vproc = regulator_get_voltage(proc_reg); - if (old_vproc < 0) { -- pr_err("%s: invalid Vproc value: %d\n", __func__, old_vproc); -+ dev_err(info->cpu_dev, -+ "invalid Vproc value: %d\n", old_vproc); - return old_vproc; - } - /* Vsram should not exceed the maximum allowed voltage of SoC. */ -@@ -83,14 +84,14 @@ static int mtk_cpufreq_voltage_tracking( - do { - old_vsram = regulator_get_voltage(sram_reg); - if (old_vsram < 0) { -- pr_err("%s: invalid Vsram value: %d\n", -- __func__, old_vsram); -+ dev_err(info->cpu_dev, -+ "invalid Vsram value: %d\n", old_vsram); - return old_vsram; - } - old_vproc = regulator_get_voltage(proc_reg); - if (old_vproc < 0) { -- pr_err("%s: invalid Vproc value: %d\n", -- __func__, old_vproc); -+ dev_err(info->cpu_dev, -+ "invalid Vproc value: %d\n", old_vproc); - return old_vproc; - } - -@@ -138,14 +139,14 @@ static int mtk_cpufreq_voltage_tracking( - do { - old_vproc = regulator_get_voltage(proc_reg); - if (old_vproc < 0) { -- pr_err("%s: invalid Vproc value: %d\n", -- __func__, old_vproc); -+ dev_err(info->cpu_dev, -+ "invalid Vproc value: %d\n", old_vproc); - return old_vproc; - } - old_vsram = regulator_get_voltage(sram_reg); - if (old_vsram < 0) { -- pr_err("%s: invalid Vsram value: %d\n", -- __func__, old_vsram); -+ dev_err(info->cpu_dev, -+ "invalid Vsram value: %d\n", old_vsram); - return old_vsram; - } - -@@ -216,7 +217,7 @@ static int mtk_cpufreq_set_target(struct - old_freq_hz = clk_get_rate(cpu_clk); - old_vproc = regulator_get_voltage(info->proc_reg); - if (old_vproc < 0) { -- pr_err("%s: invalid Vproc value: %d\n", __func__, old_vproc); -+ dev_err(cpu_dev, "invalid Vproc value: %d\n", old_vproc); - return old_vproc; - } - -@@ -224,8 +225,8 @@ static int mtk_cpufreq_set_target(struct - - opp = dev_pm_opp_find_freq_ceil(cpu_dev, &freq_hz); - if (IS_ERR(opp)) { -- pr_err("cpu%d: failed to find OPP for %ld\n", -- policy->cpu, freq_hz); -+ dev_err(cpu_dev, "cpu%d: failed to find OPP for %ld\n", -+ policy->cpu, freq_hz); - return PTR_ERR(opp); - } - vproc = dev_pm_opp_get_voltage(opp); -@@ -239,8 +240,8 @@ static int mtk_cpufreq_set_target(struct - if (old_vproc < target_vproc) { - ret = mtk_cpufreq_set_voltage(info, target_vproc); - if (ret) { -- pr_err("cpu%d: failed to scale up voltage!\n", -- policy->cpu); -+ dev_err(cpu_dev, -+ "cpu%d: failed to scale up voltage!\n", policy->cpu); - mtk_cpufreq_set_voltage(info, old_vproc); - return ret; - } -@@ -249,8 +250,8 @@ static int mtk_cpufreq_set_target(struct - /* Reparent the CPU clock to intermediate clock. */ - ret = clk_set_parent(cpu_clk, info->inter_clk); - if (ret) { -- pr_err("cpu%d: failed to re-parent cpu clock!\n", -- policy->cpu); -+ dev_err(cpu_dev, -+ "cpu%d: failed to re-parent cpu clock!\n", policy->cpu); - mtk_cpufreq_set_voltage(info, old_vproc); - WARN_ON(1); - return ret; -@@ -259,8 +260,8 @@ static int mtk_cpufreq_set_target(struct - /* Set the original PLL to target rate. */ - ret = clk_set_rate(armpll, freq_hz); - if (ret) { -- pr_err("cpu%d: failed to scale cpu clock rate!\n", -- policy->cpu); -+ dev_err(cpu_dev, -+ "cpu%d: failed to scale cpu clock rate!\n", policy->cpu); - clk_set_parent(cpu_clk, armpll); - mtk_cpufreq_set_voltage(info, old_vproc); - return ret; -@@ -269,8 +270,8 @@ static int mtk_cpufreq_set_target(struct - /* Set parent of CPU clock back to the original PLL. */ - ret = clk_set_parent(cpu_clk, armpll); - if (ret) { -- pr_err("cpu%d: failed to re-parent cpu clock!\n", -- policy->cpu); -+ dev_err(cpu_dev, -+ "cpu%d: failed to re-parent cpu clock!\n", policy->cpu); - mtk_cpufreq_set_voltage(info, inter_vproc); - WARN_ON(1); - return ret; -@@ -283,8 +284,8 @@ static int mtk_cpufreq_set_target(struct - if (vproc < inter_vproc || vproc < old_vproc) { - ret = mtk_cpufreq_set_voltage(info, vproc); - if (ret) { -- pr_err("cpu%d: failed to scale down voltage!\n", -- policy->cpu); -+ dev_err(cpu_dev, -+ "cpu%d: failed to scale down voltage!\n", policy->cpu); - clk_set_parent(cpu_clk, info->inter_clk); - clk_set_rate(armpll, old_freq_hz); - clk_set_parent(cpu_clk, armpll); -@@ -450,15 +451,16 @@ static int mtk_cpufreq_init(struct cpufr - - info = mtk_cpu_dvfs_info_lookup(policy->cpu); - if (!info) { -- pr_err("dvfs info for cpu%d is not initialized.\n", -- policy->cpu); -+ dev_err(info->cpu_dev, -+ "dvfs info for cpu%d is not initialized.\n", policy->cpu); - return -EINVAL; - } - - ret = dev_pm_opp_init_cpufreq_table(info->cpu_dev, &freq_table); - if (ret) { -- pr_err("failed to init cpufreq table for cpu%d: %d\n", -- policy->cpu, ret); -+ dev_err(info->cpu_dev, -+ "failed to init cpufreq table for cpu%d: %d\n", -+ policy->cpu, ret); - return ret; - } - diff --git a/target/linux/mediatek/patches-5.15/350-05-cpufreq-mediatek-Replace-old_-with-pre_.patch b/target/linux/mediatek/patches-5.15/350-05-cpufreq-mediatek-Replace-old_-with-pre_.patch deleted file mode 100644 index 8506f4e477..0000000000 --- a/target/linux/mediatek/patches-5.15/350-05-cpufreq-mediatek-Replace-old_-with-pre_.patch +++ /dev/null @@ -1,201 +0,0 @@ -From 35832d9f9c5c1da01420d962dc56e7e61d104829 Mon Sep 17 00:00:00 2001 -From: Rex-BC Chen -Date: Fri, 22 Apr 2022 15:52:28 +0800 -Subject: [PATCH 05/21] cpufreq: mediatek: Replace old_* with pre_* - -To make driver more readable, replace old_* with pre_*. - -Signed-off-by: Rex-BC Chen -Reviewed-by: AngeloGioacchino Del Regno -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 84 +++++++++++++++--------------- - 1 file changed, 42 insertions(+), 42 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -63,18 +63,18 @@ static int mtk_cpufreq_voltage_tracking( - { - struct regulator *proc_reg = info->proc_reg; - struct regulator *sram_reg = info->sram_reg; -- int old_vproc, old_vsram, new_vsram, vsram, vproc, ret; -+ int pre_vproc, pre_vsram, new_vsram, vsram, vproc, ret; - -- old_vproc = regulator_get_voltage(proc_reg); -- if (old_vproc < 0) { -+ pre_vproc = regulator_get_voltage(proc_reg); -+ if (pre_vproc < 0) { - dev_err(info->cpu_dev, -- "invalid Vproc value: %d\n", old_vproc); -- return old_vproc; -+ "invalid Vproc value: %d\n", pre_vproc); -+ return pre_vproc; - } - /* Vsram should not exceed the maximum allowed voltage of SoC. */ - new_vsram = min(new_vproc + MIN_VOLT_SHIFT, MAX_VOLT_LIMIT); - -- if (old_vproc < new_vproc) { -+ if (pre_vproc < new_vproc) { - /* - * When scaling up voltages, Vsram and Vproc scale up step - * by step. At each step, set Vsram to (Vproc + 200mV) first, -@@ -82,20 +82,20 @@ static int mtk_cpufreq_voltage_tracking( - * Keep doing it until Vsram and Vproc hit target voltages. - */ - do { -- old_vsram = regulator_get_voltage(sram_reg); -- if (old_vsram < 0) { -+ pre_vsram = regulator_get_voltage(sram_reg); -+ if (pre_vsram < 0) { - dev_err(info->cpu_dev, -- "invalid Vsram value: %d\n", old_vsram); -- return old_vsram; -+ "invalid Vsram value: %d\n", pre_vsram); -+ return pre_vsram; - } -- old_vproc = regulator_get_voltage(proc_reg); -- if (old_vproc < 0) { -+ pre_vproc = regulator_get_voltage(proc_reg); -+ if (pre_vproc < 0) { - dev_err(info->cpu_dev, -- "invalid Vproc value: %d\n", old_vproc); -- return old_vproc; -+ "invalid Vproc value: %d\n", pre_vproc); -+ return pre_vproc; - } - -- vsram = min(new_vsram, old_vproc + MAX_VOLT_SHIFT); -+ vsram = min(new_vsram, pre_vproc + MAX_VOLT_SHIFT); - - if (vsram + VOLT_TOL >= MAX_VOLT_LIMIT) { - vsram = MAX_VOLT_LIMIT; -@@ -124,12 +124,12 @@ static int mtk_cpufreq_voltage_tracking( - ret = regulator_set_voltage(proc_reg, vproc, - vproc + VOLT_TOL); - if (ret) { -- regulator_set_voltage(sram_reg, old_vsram, -- old_vsram); -+ regulator_set_voltage(sram_reg, pre_vsram, -+ pre_vsram); - return ret; - } - } while (vproc < new_vproc || vsram < new_vsram); -- } else if (old_vproc > new_vproc) { -+ } else if (pre_vproc > new_vproc) { - /* - * When scaling down voltages, Vsram and Vproc scale down step - * by step. At each step, set Vproc to (Vsram - 200mV) first, -@@ -137,20 +137,20 @@ static int mtk_cpufreq_voltage_tracking( - * Keep doing it until Vsram and Vproc hit target voltages. - */ - do { -- old_vproc = regulator_get_voltage(proc_reg); -- if (old_vproc < 0) { -+ pre_vproc = regulator_get_voltage(proc_reg); -+ if (pre_vproc < 0) { - dev_err(info->cpu_dev, -- "invalid Vproc value: %d\n", old_vproc); -- return old_vproc; -+ "invalid Vproc value: %d\n", pre_vproc); -+ return pre_vproc; - } -- old_vsram = regulator_get_voltage(sram_reg); -- if (old_vsram < 0) { -+ pre_vsram = regulator_get_voltage(sram_reg); -+ if (pre_vsram < 0) { - dev_err(info->cpu_dev, -- "invalid Vsram value: %d\n", old_vsram); -- return old_vsram; -+ "invalid Vsram value: %d\n", pre_vsram); -+ return pre_vsram; - } - -- vproc = max(new_vproc, old_vsram - MAX_VOLT_SHIFT); -+ vproc = max(new_vproc, pre_vsram - MAX_VOLT_SHIFT); - ret = regulator_set_voltage(proc_reg, vproc, - vproc + VOLT_TOL); - if (ret) -@@ -180,8 +180,8 @@ static int mtk_cpufreq_voltage_tracking( - } - - if (ret) { -- regulator_set_voltage(proc_reg, old_vproc, -- old_vproc); -+ regulator_set_voltage(proc_reg, pre_vproc, -+ pre_vproc); - return ret; - } - } while (vproc > new_vproc + VOLT_TOL || -@@ -209,16 +209,16 @@ static int mtk_cpufreq_set_target(struct - struct mtk_cpu_dvfs_info *info = policy->driver_data; - struct device *cpu_dev = info->cpu_dev; - struct dev_pm_opp *opp; -- long freq_hz, old_freq_hz; -- int vproc, old_vproc, inter_vproc, target_vproc, ret; -+ long freq_hz, pre_freq_hz; -+ int vproc, pre_vproc, inter_vproc, target_vproc, ret; - - inter_vproc = info->intermediate_voltage; - -- old_freq_hz = clk_get_rate(cpu_clk); -- old_vproc = regulator_get_voltage(info->proc_reg); -- if (old_vproc < 0) { -- dev_err(cpu_dev, "invalid Vproc value: %d\n", old_vproc); -- return old_vproc; -+ pre_freq_hz = clk_get_rate(cpu_clk); -+ pre_vproc = regulator_get_voltage(info->proc_reg); -+ if (pre_vproc < 0) { -+ dev_err(cpu_dev, "invalid Vproc value: %d\n", pre_vproc); -+ return pre_vproc; - } - - freq_hz = freq_table[index].frequency * 1000; -@@ -237,12 +237,12 @@ static int mtk_cpufreq_set_target(struct - * current voltage, scale up voltage first. - */ - target_vproc = (inter_vproc > vproc) ? inter_vproc : vproc; -- if (old_vproc < target_vproc) { -+ if (pre_vproc < target_vproc) { - ret = mtk_cpufreq_set_voltage(info, target_vproc); - if (ret) { - dev_err(cpu_dev, - "cpu%d: failed to scale up voltage!\n", policy->cpu); -- mtk_cpufreq_set_voltage(info, old_vproc); -+ mtk_cpufreq_set_voltage(info, pre_vproc); - return ret; - } - } -@@ -252,7 +252,7 @@ static int mtk_cpufreq_set_target(struct - if (ret) { - dev_err(cpu_dev, - "cpu%d: failed to re-parent cpu clock!\n", policy->cpu); -- mtk_cpufreq_set_voltage(info, old_vproc); -+ mtk_cpufreq_set_voltage(info, pre_vproc); - WARN_ON(1); - return ret; - } -@@ -263,7 +263,7 @@ static int mtk_cpufreq_set_target(struct - dev_err(cpu_dev, - "cpu%d: failed to scale cpu clock rate!\n", policy->cpu); - clk_set_parent(cpu_clk, armpll); -- mtk_cpufreq_set_voltage(info, old_vproc); -+ mtk_cpufreq_set_voltage(info, pre_vproc); - return ret; - } - -@@ -281,13 +281,13 @@ static int mtk_cpufreq_set_target(struct - * If the new voltage is lower than the intermediate voltage or the - * original voltage, scale down to the new voltage. - */ -- if (vproc < inter_vproc || vproc < old_vproc) { -+ if (vproc < inter_vproc || vproc < pre_vproc) { - ret = mtk_cpufreq_set_voltage(info, vproc); - if (ret) { - dev_err(cpu_dev, - "cpu%d: failed to scale down voltage!\n", policy->cpu); - clk_set_parent(cpu_clk, info->inter_clk); -- clk_set_rate(armpll, old_freq_hz); -+ clk_set_rate(armpll, pre_freq_hz); - clk_set_parent(cpu_clk, armpll); - return ret; - } diff --git a/target/linux/mediatek/patches-5.15/350-06-cpufreq-mediatek-Record-previous-target-vproc-value.patch b/target/linux/mediatek/patches-5.15/350-06-cpufreq-mediatek-Record-previous-target-vproc-value.patch deleted file mode 100644 index 94e6617d26..0000000000 --- a/target/linux/mediatek/patches-5.15/350-06-cpufreq-mediatek-Record-previous-target-vproc-value.patch +++ /dev/null @@ -1,64 +0,0 @@ -From 34737eb8d0daa0d4183f10286a2f55d8788066bc Mon Sep 17 00:00:00 2001 -From: Jia-Wei Chang -Date: Fri, 22 Apr 2022 15:52:29 +0800 -Subject: [PATCH 06/21] cpufreq: mediatek: Record previous target vproc value - -We found the buck voltage may not be exactly the same with what we set -because CPU may share the same buck with other module. -Therefore, we need to record the previous desired value instead of reading -it from regulators. - -Signed-off-by: Andrew-sh.Cheng -Signed-off-by: Jia-Wei Chang -Signed-off-by: Rex-BC Chen -Reviewed-by: AngeloGioacchino Del Regno -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 20 ++++++++++++++++---- - 1 file changed, 16 insertions(+), 4 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -40,6 +40,7 @@ struct mtk_cpu_dvfs_info { - struct list_head list_head; - int intermediate_voltage; - bool need_voltage_tracking; -+ int pre_vproc; - }; - - static struct platform_device *cpufreq_pdev; -@@ -193,11 +194,17 @@ static int mtk_cpufreq_voltage_tracking( - - static int mtk_cpufreq_set_voltage(struct mtk_cpu_dvfs_info *info, int vproc) - { -+ int ret; -+ - if (info->need_voltage_tracking) -- return mtk_cpufreq_voltage_tracking(info, vproc); -+ ret = mtk_cpufreq_voltage_tracking(info, vproc); - else -- return regulator_set_voltage(info->proc_reg, vproc, -- vproc + VOLT_TOL); -+ ret = regulator_set_voltage(info->proc_reg, vproc, -+ MAX_VOLT_LIMIT); -+ if (!ret) -+ info->pre_vproc = vproc; -+ -+ return ret; - } - - static int mtk_cpufreq_set_target(struct cpufreq_policy *policy, -@@ -215,7 +222,12 @@ static int mtk_cpufreq_set_target(struct - inter_vproc = info->intermediate_voltage; - - pre_freq_hz = clk_get_rate(cpu_clk); -- pre_vproc = regulator_get_voltage(info->proc_reg); -+ -+ if (unlikely(info->pre_vproc <= 0)) -+ pre_vproc = regulator_get_voltage(info->proc_reg); -+ else -+ pre_vproc = info->pre_vproc; -+ - if (pre_vproc < 0) { - dev_err(cpu_dev, "invalid Vproc value: %d\n", pre_vproc); - return pre_vproc; diff --git a/target/linux/mediatek/patches-5.15/350-07-cpufreq-mediatek-Make-sram-regulator-optional.patch b/target/linux/mediatek/patches-5.15/350-07-cpufreq-mediatek-Make-sram-regulator-optional.patch deleted file mode 100644 index 4b74873b15..0000000000 --- a/target/linux/mediatek/patches-5.15/350-07-cpufreq-mediatek-Make-sram-regulator-optional.patch +++ /dev/null @@ -1,30 +0,0 @@ -From f6114c2bc563a8050e9dc874ad87e1448865f031 Mon Sep 17 00:00:00 2001 -From: Jia-Wei Chang -Date: Fri, 22 Apr 2022 15:52:33 +0800 -Subject: [PATCH 07/21] cpufreq: mediatek: Make sram regulator optional - -For some MediaTek SoCs, like MT8186, it's possible that the sram regulator -is shared between CPU and CCI. -We hope regulator framework can return error for error handling rather -than a dummy handler from regulator_get api. -Therefore, we choose to use regulator_get_optional. - -Signed-off-by: Jia-Wei Chang -Signed-off-by: Rex-BC Chen -Reviewed-by: AngeloGioacchino Del Regno -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -354,7 +354,7 @@ static int mtk_cpu_dvfs_info_init(struct - } - - /* Both presence and absence of sram regulator are valid cases. */ -- info->sram_reg = regulator_get_exclusive(cpu_dev, "sram"); -+ info->sram_reg = regulator_get_optional(cpu_dev, "sram"); - if (IS_ERR(info->sram_reg)) - info->sram_reg = NULL; - else { diff --git a/target/linux/mediatek/patches-5.15/350-08-cpufreq-mediatek-Fix-NULL-pointer-dereference-in-med.patch b/target/linux/mediatek/patches-5.15/350-08-cpufreq-mediatek-Fix-NULL-pointer-dereference-in-med.patch deleted file mode 100644 index f2f572a753..0000000000 --- a/target/linux/mediatek/patches-5.15/350-08-cpufreq-mediatek-Fix-NULL-pointer-dereference-in-med.patch +++ /dev/null @@ -1,32 +0,0 @@ -From fa7030d8ad4638acfd9e0fac84a20716d031dc95 Mon Sep 17 00:00:00 2001 -From: Wan Jiabing -Date: Tue, 26 Apr 2022 19:17:14 +0800 -Subject: [PATCH 08/21] cpufreq: mediatek: Fix NULL pointer dereference in - mediatek-cpufreq - -Fix following coccicheck error: -drivers/cpufreq/mediatek-cpufreq.c:464:16-23: ERROR: info is NULL but dereferenced. - -Use pr_err instead of dev_err to avoid dereferring a NULL pointer. - -Fixes: f52b16ba9fe4 ("cpufreq: mediatek: Use device print to show logs") -Signed-off-by: Wan Jiabing -Reviewed-by: Matthias Brugger -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 4 ++-- - 1 file changed, 2 insertions(+), 2 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -463,8 +463,8 @@ static int mtk_cpufreq_init(struct cpufr - - info = mtk_cpu_dvfs_info_lookup(policy->cpu); - if (!info) { -- dev_err(info->cpu_dev, -- "dvfs info for cpu%d is not initialized.\n", policy->cpu); -+ pr_err("dvfs info for cpu%d is not initialized.\n", -+ policy->cpu); - return -EINVAL; - } - diff --git a/target/linux/mediatek/patches-5.15/350-09-cpufreq-mediatek-Move-voltage-limits-to-platform-dat.patch b/target/linux/mediatek/patches-5.15/350-09-cpufreq-mediatek-Move-voltage-limits-to-platform-dat.patch deleted file mode 100644 index 23b319648d..0000000000 --- a/target/linux/mediatek/patches-5.15/350-09-cpufreq-mediatek-Move-voltage-limits-to-platform-dat.patch +++ /dev/null @@ -1,227 +0,0 @@ -From be2354b064e6bafbbad599ae2e10569ba4f7d5a6 Mon Sep 17 00:00:00 2001 -From: Rex-BC Chen -Date: Thu, 5 May 2022 19:52:19 +0800 -Subject: [PATCH 09/21] cpufreq: mediatek: Move voltage limits to platform data - -Voltages and shifts are defined as macros originally. -There are different requirements of these values for each MediaTek SoCs. -Therefore, we add the platform data and move these values into it. - -Signed-off-by: Jia-Wei Chang -Signed-off-by: Rex-BC Chen -Reviewed-by: AngeloGioacchino Del Regno -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 84 +++++++++++++++++++++--------- - 1 file changed, 58 insertions(+), 26 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -10,15 +10,21 @@ - #include - #include - #include -+#include - #include - #include - #include - --#define MIN_VOLT_SHIFT (100000) --#define MAX_VOLT_SHIFT (200000) --#define MAX_VOLT_LIMIT (1150000) - #define VOLT_TOL (10000) - -+struct mtk_cpufreq_platform_data { -+ int min_volt_shift; -+ int max_volt_shift; -+ int proc_max_volt; -+ int sram_min_volt; -+ int sram_max_volt; -+}; -+ - /* - * The struct mtk_cpu_dvfs_info holds necessary information for doing CPU DVFS - * on each CPU power/clock domain of Mediatek SoCs. Each CPU cluster in -@@ -41,6 +47,7 @@ struct mtk_cpu_dvfs_info { - int intermediate_voltage; - bool need_voltage_tracking; - int pre_vproc; -+ const struct mtk_cpufreq_platform_data *soc_data; - }; - - static struct platform_device *cpufreq_pdev; -@@ -62,6 +69,7 @@ static struct mtk_cpu_dvfs_info *mtk_cpu - static int mtk_cpufreq_voltage_tracking(struct mtk_cpu_dvfs_info *info, - int new_vproc) - { -+ const struct mtk_cpufreq_platform_data *soc_data = info->soc_data; - struct regulator *proc_reg = info->proc_reg; - struct regulator *sram_reg = info->sram_reg; - int pre_vproc, pre_vsram, new_vsram, vsram, vproc, ret; -@@ -73,7 +81,8 @@ static int mtk_cpufreq_voltage_tracking( - return pre_vproc; - } - /* Vsram should not exceed the maximum allowed voltage of SoC. */ -- new_vsram = min(new_vproc + MIN_VOLT_SHIFT, MAX_VOLT_LIMIT); -+ new_vsram = min(new_vproc + soc_data->min_volt_shift, -+ soc_data->sram_max_volt); - - if (pre_vproc < new_vproc) { - /* -@@ -96,10 +105,11 @@ static int mtk_cpufreq_voltage_tracking( - return pre_vproc; - } - -- vsram = min(new_vsram, pre_vproc + MAX_VOLT_SHIFT); -+ vsram = min(new_vsram, -+ pre_vproc + soc_data->min_volt_shift); - -- if (vsram + VOLT_TOL >= MAX_VOLT_LIMIT) { -- vsram = MAX_VOLT_LIMIT; -+ if (vsram + VOLT_TOL >= soc_data->sram_max_volt) { -+ vsram = soc_data->sram_max_volt; - - /* - * If the target Vsram hits the maximum voltage, -@@ -117,7 +127,7 @@ static int mtk_cpufreq_voltage_tracking( - ret = regulator_set_voltage(sram_reg, vsram, - vsram + VOLT_TOL); - -- vproc = vsram - MIN_VOLT_SHIFT; -+ vproc = vsram - soc_data->min_volt_shift; - } - if (ret) - return ret; -@@ -151,7 +161,8 @@ static int mtk_cpufreq_voltage_tracking( - return pre_vsram; - } - -- vproc = max(new_vproc, pre_vsram - MAX_VOLT_SHIFT); -+ vproc = max(new_vproc, -+ pre_vsram - soc_data->max_volt_shift); - ret = regulator_set_voltage(proc_reg, vproc, - vproc + VOLT_TOL); - if (ret) -@@ -160,10 +171,11 @@ static int mtk_cpufreq_voltage_tracking( - if (vproc == new_vproc) - vsram = new_vsram; - else -- vsram = max(new_vsram, vproc + MIN_VOLT_SHIFT); -+ vsram = max(new_vsram, -+ vproc + soc_data->min_volt_shift); - -- if (vsram + VOLT_TOL >= MAX_VOLT_LIMIT) { -- vsram = MAX_VOLT_LIMIT; -+ if (vsram + VOLT_TOL >= soc_data->sram_max_volt) { -+ vsram = soc_data->sram_max_volt; - - /* - * If the target Vsram hits the maximum voltage, -@@ -194,13 +206,14 @@ static int mtk_cpufreq_voltage_tracking( - - static int mtk_cpufreq_set_voltage(struct mtk_cpu_dvfs_info *info, int vproc) - { -+ const struct mtk_cpufreq_platform_data *soc_data = info->soc_data; - int ret; - - if (info->need_voltage_tracking) - ret = mtk_cpufreq_voltage_tracking(info, vproc); - else - ret = regulator_set_voltage(info->proc_reg, vproc, -- MAX_VOLT_LIMIT); -+ soc_data->proc_max_volt); - if (!ret) - info->pre_vproc = vproc; - -@@ -509,9 +522,17 @@ static struct cpufreq_driver mtk_cpufreq - - static int mtk_cpufreq_probe(struct platform_device *pdev) - { -+ const struct mtk_cpufreq_platform_data *data; - struct mtk_cpu_dvfs_info *info, *tmp; - int cpu, ret; - -+ data = dev_get_platdata(&pdev->dev); -+ if (!data) { -+ dev_err(&pdev->dev, -+ "failed to get mtk cpufreq platform data\n"); -+ return -ENODEV; -+ } -+ - for_each_possible_cpu(cpu) { - info = mtk_cpu_dvfs_info_lookup(cpu); - if (info) -@@ -523,6 +544,7 @@ static int mtk_cpufreq_probe(struct plat - goto release_dvfs_info_list; - } - -+ info->soc_data = data; - ret = mtk_cpu_dvfs_info_init(info, cpu); - if (ret) { - dev_err(&pdev->dev, -@@ -558,20 +580,27 @@ static struct platform_driver mtk_cpufre - .probe = mtk_cpufreq_probe, - }; - -+static const struct mtk_cpufreq_platform_data mt2701_platform_data = { -+ .min_volt_shift = 100000, -+ .max_volt_shift = 200000, -+ .proc_max_volt = 1150000, -+ .sram_min_volt = 0, -+ .sram_max_volt = 1150000, -+}; -+ - /* List of machines supported by this driver */ - static const struct of_device_id mtk_cpufreq_machines[] __initconst = { -- { .compatible = "mediatek,mt2701", }, -- { .compatible = "mediatek,mt2712", }, -- { .compatible = "mediatek,mt7622", }, -- { .compatible = "mediatek,mt7623", }, -- { .compatible = "mediatek,mt8167", }, -- { .compatible = "mediatek,mt817x", }, -- { .compatible = "mediatek,mt8173", }, -- { .compatible = "mediatek,mt8176", }, -- { .compatible = "mediatek,mt8183", }, -- { .compatible = "mediatek,mt8365", }, -- { .compatible = "mediatek,mt8516", }, -- -+ { .compatible = "mediatek,mt2701", .data = &mt2701_platform_data }, -+ { .compatible = "mediatek,mt2712", .data = &mt2701_platform_data }, -+ { .compatible = "mediatek,mt7622", .data = &mt2701_platform_data }, -+ { .compatible = "mediatek,mt7623", .data = &mt2701_platform_data }, -+ { .compatible = "mediatek,mt8167", .data = &mt2701_platform_data }, -+ { .compatible = "mediatek,mt817x", .data = &mt2701_platform_data }, -+ { .compatible = "mediatek,mt8173", .data = &mt2701_platform_data }, -+ { .compatible = "mediatek,mt8176", .data = &mt2701_platform_data }, -+ { .compatible = "mediatek,mt8183", .data = &mt2701_platform_data }, -+ { .compatible = "mediatek,mt8365", .data = &mt2701_platform_data }, -+ { .compatible = "mediatek,mt8516", .data = &mt2701_platform_data }, - { } - }; - MODULE_DEVICE_TABLE(of, mtk_cpufreq_machines); -@@ -580,6 +609,7 @@ static int __init mtk_cpufreq_driver_ini - { - struct device_node *np; - const struct of_device_id *match; -+ const struct mtk_cpufreq_platform_data *data; - int err; - - np = of_find_node_by_path("/"); -@@ -592,6 +622,7 @@ static int __init mtk_cpufreq_driver_ini - pr_debug("Machine is not compatible with mtk-cpufreq\n"); - return -ENODEV; - } -+ data = match->data; - - err = platform_driver_register(&mtk_cpufreq_platdrv); - if (err) -@@ -603,7 +634,8 @@ static int __init mtk_cpufreq_driver_ini - * and the device registration codes are put here to handle defer - * probing. - */ -- cpufreq_pdev = platform_device_register_simple("mtk-cpufreq", -1, NULL, 0); -+ cpufreq_pdev = platform_device_register_data(NULL, "mtk-cpufreq", -1, -+ data, sizeof(*data)); - if (IS_ERR(cpufreq_pdev)) { - pr_err("failed to register mtk-cpufreq platform device\n"); - platform_driver_unregister(&mtk_cpufreq_platdrv); diff --git a/target/linux/mediatek/patches-5.15/350-10-cpufreq-mediatek-Refine-mtk_cpufreq_voltage_tracking.patch b/target/linux/mediatek/patches-5.15/350-10-cpufreq-mediatek-Refine-mtk_cpufreq_voltage_tracking.patch deleted file mode 100644 index 0ba9471ffa..0000000000 --- a/target/linux/mediatek/patches-5.15/350-10-cpufreq-mediatek-Refine-mtk_cpufreq_voltage_tracking.patch +++ /dev/null @@ -1,255 +0,0 @@ -From 944b041c91f1e1cd762c39c1222f078550149486 Mon Sep 17 00:00:00 2001 -From: Jia-Wei Chang -Date: Thu, 5 May 2022 19:52:20 +0800 -Subject: [PATCH 10/21] cpufreq: mediatek: Refine - mtk_cpufreq_voltage_tracking() - -Because the difference of sram and proc should in a range of min_volt_shift -and max_volt_shift. We need to adjust the sram and proc step by step. - -We replace VOLT_TOL (voltage tolerance) with the platform data and update the -logic to determine the voltage boundary and invoking regulator_set_voltage. - -- Use 'sram_min_volt' and 'sram_max_volt' to determine the voltage boundary - of sram regulator. -- Use (sram_min_volt - min_volt_shift) and 'proc_max_volt' to determine the - voltage boundary of vproc regulator. - -Moreover, to prevent infinite loop when tracking voltage, we calculate the -maximum value for each platform data. -We assume min voltage is 0 and tracking target voltage using -min_volt_shift for each iteration. -The retry_max is 3 times of expeted iteration count. - -Signed-off-by: Jia-Wei Chang -Signed-off-by: Rex-BC Chen -Reviewed-by: AngeloGioacchino Del Regno -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 147 ++++++++++------------------- - 1 file changed, 51 insertions(+), 96 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -8,6 +8,7 @@ - #include - #include - #include -+#include - #include - #include - #include -@@ -15,8 +16,6 @@ - #include - #include - --#define VOLT_TOL (10000) -- - struct mtk_cpufreq_platform_data { - int min_volt_shift; - int max_volt_shift; -@@ -48,6 +47,7 @@ struct mtk_cpu_dvfs_info { - bool need_voltage_tracking; - int pre_vproc; - const struct mtk_cpufreq_platform_data *soc_data; -+ int vtrack_max; - }; - - static struct platform_device *cpufreq_pdev; -@@ -73,6 +73,7 @@ static int mtk_cpufreq_voltage_tracking( - struct regulator *proc_reg = info->proc_reg; - struct regulator *sram_reg = info->sram_reg; - int pre_vproc, pre_vsram, new_vsram, vsram, vproc, ret; -+ int retry = info->vtrack_max; - - pre_vproc = regulator_get_voltage(proc_reg); - if (pre_vproc < 0) { -@@ -80,91 +81,44 @@ static int mtk_cpufreq_voltage_tracking( - "invalid Vproc value: %d\n", pre_vproc); - return pre_vproc; - } -- /* Vsram should not exceed the maximum allowed voltage of SoC. */ -- new_vsram = min(new_vproc + soc_data->min_volt_shift, -- soc_data->sram_max_volt); -- -- if (pre_vproc < new_vproc) { -- /* -- * When scaling up voltages, Vsram and Vproc scale up step -- * by step. At each step, set Vsram to (Vproc + 200mV) first, -- * then set Vproc to (Vsram - 100mV). -- * Keep doing it until Vsram and Vproc hit target voltages. -- */ -- do { -- pre_vsram = regulator_get_voltage(sram_reg); -- if (pre_vsram < 0) { -- dev_err(info->cpu_dev, -- "invalid Vsram value: %d\n", pre_vsram); -- return pre_vsram; -- } -- pre_vproc = regulator_get_voltage(proc_reg); -- if (pre_vproc < 0) { -- dev_err(info->cpu_dev, -- "invalid Vproc value: %d\n", pre_vproc); -- return pre_vproc; -- } - -- vsram = min(new_vsram, -- pre_vproc + soc_data->min_volt_shift); -+ pre_vsram = regulator_get_voltage(sram_reg); -+ if (pre_vsram < 0) { -+ dev_err(info->cpu_dev, "invalid Vsram value: %d\n", pre_vsram); -+ return pre_vsram; -+ } - -- if (vsram + VOLT_TOL >= soc_data->sram_max_volt) { -- vsram = soc_data->sram_max_volt; -+ new_vsram = clamp(new_vproc + soc_data->min_volt_shift, -+ soc_data->sram_min_volt, soc_data->sram_max_volt); -+ -+ do { -+ if (pre_vproc <= new_vproc) { -+ vsram = clamp(pre_vproc + soc_data->max_volt_shift, -+ soc_data->sram_min_volt, new_vsram); -+ ret = regulator_set_voltage(sram_reg, vsram, -+ soc_data->sram_max_volt); - -- /* -- * If the target Vsram hits the maximum voltage, -- * try to set the exact voltage value first. -- */ -- ret = regulator_set_voltage(sram_reg, vsram, -- vsram); -- if (ret) -- ret = regulator_set_voltage(sram_reg, -- vsram - VOLT_TOL, -- vsram); -+ if (ret) -+ return ret; - -+ if (vsram == soc_data->sram_max_volt || -+ new_vsram == soc_data->sram_min_volt) - vproc = new_vproc; -- } else { -- ret = regulator_set_voltage(sram_reg, vsram, -- vsram + VOLT_TOL); -- -+ else - vproc = vsram - soc_data->min_volt_shift; -- } -- if (ret) -- return ret; - - ret = regulator_set_voltage(proc_reg, vproc, -- vproc + VOLT_TOL); -+ soc_data->proc_max_volt); - if (ret) { - regulator_set_voltage(sram_reg, pre_vsram, -- pre_vsram); -+ soc_data->sram_max_volt); - return ret; - } -- } while (vproc < new_vproc || vsram < new_vsram); -- } else if (pre_vproc > new_vproc) { -- /* -- * When scaling down voltages, Vsram and Vproc scale down step -- * by step. At each step, set Vproc to (Vsram - 200mV) first, -- * then set Vproc to (Vproc + 100mV). -- * Keep doing it until Vsram and Vproc hit target voltages. -- */ -- do { -- pre_vproc = regulator_get_voltage(proc_reg); -- if (pre_vproc < 0) { -- dev_err(info->cpu_dev, -- "invalid Vproc value: %d\n", pre_vproc); -- return pre_vproc; -- } -- pre_vsram = regulator_get_voltage(sram_reg); -- if (pre_vsram < 0) { -- dev_err(info->cpu_dev, -- "invalid Vsram value: %d\n", pre_vsram); -- return pre_vsram; -- } -- -+ } else if (pre_vproc > new_vproc) { - vproc = max(new_vproc, - pre_vsram - soc_data->max_volt_shift); - ret = regulator_set_voltage(proc_reg, vproc, -- vproc + VOLT_TOL); -+ soc_data->proc_max_volt); - if (ret) - return ret; - -@@ -174,32 +128,24 @@ static int mtk_cpufreq_voltage_tracking( - vsram = max(new_vsram, - vproc + soc_data->min_volt_shift); - -- if (vsram + VOLT_TOL >= soc_data->sram_max_volt) { -- vsram = soc_data->sram_max_volt; -- -- /* -- * If the target Vsram hits the maximum voltage, -- * try to set the exact voltage value first. -- */ -- ret = regulator_set_voltage(sram_reg, vsram, -- vsram); -- if (ret) -- ret = regulator_set_voltage(sram_reg, -- vsram - VOLT_TOL, -- vsram); -- } else { -- ret = regulator_set_voltage(sram_reg, vsram, -- vsram + VOLT_TOL); -- } -- -+ ret = regulator_set_voltage(sram_reg, vsram, -+ soc_data->sram_max_volt); - if (ret) { - regulator_set_voltage(proc_reg, pre_vproc, -- pre_vproc); -+ soc_data->proc_max_volt); - return ret; - } -- } while (vproc > new_vproc + VOLT_TOL || -- vsram > new_vsram + VOLT_TOL); -- } -+ } -+ -+ pre_vproc = vproc; -+ pre_vsram = vsram; -+ -+ if (--retry < 0) { -+ dev_err(info->cpu_dev, -+ "over loop count, failed to set voltage\n"); -+ return -EINVAL; -+ } -+ } while (vproc != new_vproc || vsram != new_vsram); - - return 0; - } -@@ -261,8 +207,8 @@ static int mtk_cpufreq_set_target(struct - * If the new voltage or the intermediate voltage is higher than the - * current voltage, scale up voltage first. - */ -- target_vproc = (inter_vproc > vproc) ? inter_vproc : vproc; -- if (pre_vproc < target_vproc) { -+ target_vproc = max(inter_vproc, vproc); -+ if (pre_vproc <= target_vproc) { - ret = mtk_cpufreq_set_voltage(info, target_vproc); - if (ret) { - dev_err(cpu_dev, -@@ -417,6 +363,15 @@ static int mtk_cpu_dvfs_info_init(struct - */ - info->need_voltage_tracking = (info->sram_reg != NULL); - -+ /* -+ * We assume min voltage is 0 and tracking target voltage using -+ * min_volt_shift for each iteration. -+ * The vtrack_max is 3 times of expeted iteration count. -+ */ -+ info->vtrack_max = 3 * DIV_ROUND_UP(max(info->soc_data->sram_max_volt, -+ info->soc_data->proc_max_volt), -+ info->soc_data->min_volt_shift); -+ - return 0; - - out_disable_inter_clock: diff --git a/target/linux/mediatek/patches-5.15/350-11-cpufreq-mediatek-Add-opp-notification-support.patch b/target/linux/mediatek/patches-5.15/350-11-cpufreq-mediatek-Add-opp-notification-support.patch deleted file mode 100644 index 2cb99b907a..0000000000 --- a/target/linux/mediatek/patches-5.15/350-11-cpufreq-mediatek-Add-opp-notification-support.patch +++ /dev/null @@ -1,184 +0,0 @@ -From 01be227eff7e5fc01f7c8de8f6daddd5fb17ddd1 Mon Sep 17 00:00:00 2001 -From: Rex-BC Chen -Date: Thu, 5 May 2022 19:52:21 +0800 -Subject: [PATCH 11/21] cpufreq: mediatek: Add opp notification support - -From this opp notifier, cpufreq should listen to opp notification and do -proper actions when receiving events of disable and voltage adjustment. - -One of the user for this opp notifier is MediaTek SVS. -The MediaTek Smart Voltage Scaling (SVS) is a hardware which calculates -suitable SVS bank voltages to OPP voltage table. - -Signed-off-by: Andrew-sh.Cheng -Signed-off-by: Jia-Wei Chang -Signed-off-by: Rex-BC Chen -Reviewed-by: AngeloGioacchino Del Regno -[ Viresh: Renamed opp_freq as current_freq and moved its initialization ] -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 90 +++++++++++++++++++++++++++--- - 1 file changed, 82 insertions(+), 8 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -46,6 +46,11 @@ struct mtk_cpu_dvfs_info { - int intermediate_voltage; - bool need_voltage_tracking; - int pre_vproc; -+ /* Avoid race condition for regulators between notify and policy */ -+ struct mutex reg_lock; -+ struct notifier_block opp_nb; -+ unsigned int opp_cpu; -+ unsigned long current_freq; - const struct mtk_cpufreq_platform_data *soc_data; - int vtrack_max; - }; -@@ -182,6 +187,8 @@ static int mtk_cpufreq_set_target(struct - - pre_freq_hz = clk_get_rate(cpu_clk); - -+ mutex_lock(&info->reg_lock); -+ - if (unlikely(info->pre_vproc <= 0)) - pre_vproc = regulator_get_voltage(info->proc_reg); - else -@@ -214,7 +221,7 @@ static int mtk_cpufreq_set_target(struct - dev_err(cpu_dev, - "cpu%d: failed to scale up voltage!\n", policy->cpu); - mtk_cpufreq_set_voltage(info, pre_vproc); -- return ret; -+ goto out; - } - } - -@@ -224,8 +231,7 @@ static int mtk_cpufreq_set_target(struct - dev_err(cpu_dev, - "cpu%d: failed to re-parent cpu clock!\n", policy->cpu); - mtk_cpufreq_set_voltage(info, pre_vproc); -- WARN_ON(1); -- return ret; -+ goto out; - } - - /* Set the original PLL to target rate. */ -@@ -235,7 +241,7 @@ static int mtk_cpufreq_set_target(struct - "cpu%d: failed to scale cpu clock rate!\n", policy->cpu); - clk_set_parent(cpu_clk, armpll); - mtk_cpufreq_set_voltage(info, pre_vproc); -- return ret; -+ goto out; - } - - /* Set parent of CPU clock back to the original PLL. */ -@@ -244,8 +250,7 @@ static int mtk_cpufreq_set_target(struct - dev_err(cpu_dev, - "cpu%d: failed to re-parent cpu clock!\n", policy->cpu); - mtk_cpufreq_set_voltage(info, inter_vproc); -- WARN_ON(1); -- return ret; -+ goto out; - } - - /* -@@ -260,15 +265,72 @@ static int mtk_cpufreq_set_target(struct - clk_set_parent(cpu_clk, info->inter_clk); - clk_set_rate(armpll, pre_freq_hz); - clk_set_parent(cpu_clk, armpll); -- return ret; -+ goto out; - } - } - -- return 0; -+ info->current_freq = freq_hz; -+ -+out: -+ mutex_unlock(&info->reg_lock); -+ -+ return ret; - } - - #define DYNAMIC_POWER "dynamic-power-coefficient" - -+static int mtk_cpufreq_opp_notifier(struct notifier_block *nb, -+ unsigned long event, void *data) -+{ -+ struct dev_pm_opp *opp = data; -+ struct dev_pm_opp *new_opp; -+ struct mtk_cpu_dvfs_info *info; -+ unsigned long freq, volt; -+ struct cpufreq_policy *policy; -+ int ret = 0; -+ -+ info = container_of(nb, struct mtk_cpu_dvfs_info, opp_nb); -+ -+ if (event == OPP_EVENT_ADJUST_VOLTAGE) { -+ freq = dev_pm_opp_get_freq(opp); -+ -+ mutex_lock(&info->reg_lock); -+ if (info->current_freq == freq) { -+ volt = dev_pm_opp_get_voltage(opp); -+ ret = mtk_cpufreq_set_voltage(info, volt); -+ if (ret) -+ dev_err(info->cpu_dev, -+ "failed to scale voltage: %d\n", ret); -+ } -+ mutex_unlock(&info->reg_lock); -+ } else if (event == OPP_EVENT_DISABLE) { -+ freq = dev_pm_opp_get_freq(opp); -+ -+ /* case of current opp item is disabled */ -+ if (info->current_freq == freq) { -+ freq = 1; -+ new_opp = dev_pm_opp_find_freq_ceil(info->cpu_dev, -+ &freq); -+ if (IS_ERR(new_opp)) { -+ dev_err(info->cpu_dev, -+ "all opp items are disabled\n"); -+ ret = PTR_ERR(new_opp); -+ return notifier_from_errno(ret); -+ } -+ -+ dev_pm_opp_put(new_opp); -+ policy = cpufreq_cpu_get(info->opp_cpu); -+ if (policy) { -+ cpufreq_driver_target(policy, freq / 1000, -+ CPUFREQ_RELATION_L); -+ cpufreq_cpu_put(policy); -+ } -+ } -+ } -+ -+ return notifier_from_errno(ret); -+} -+ - static int mtk_cpu_dvfs_info_init(struct mtk_cpu_dvfs_info *info, int cpu) - { - struct device *cpu_dev; -@@ -357,6 +419,17 @@ static int mtk_cpu_dvfs_info_init(struct - info->intermediate_voltage = dev_pm_opp_get_voltage(opp); - dev_pm_opp_put(opp); - -+ mutex_init(&info->reg_lock); -+ info->current_freq = clk_get_rate(info->cpu_clk); -+ -+ info->opp_cpu = cpu; -+ info->opp_nb.notifier_call = mtk_cpufreq_opp_notifier; -+ ret = dev_pm_opp_register_notifier(cpu_dev, &info->opp_nb); -+ if (ret) { -+ dev_err(cpu_dev, "cpu%d: failed to register opp notifier\n", cpu); -+ goto out_disable_inter_clock; -+ } -+ - /* - * If SRAM regulator is present, software "voltage tracking" is needed - * for this CPU power domain. -@@ -421,6 +494,7 @@ static void mtk_cpu_dvfs_info_release(st - } - - dev_pm_opp_of_cpumask_remove_table(&info->cpus); -+ dev_pm_opp_unregister_notifier(info->cpu_dev, &info->opp_nb); - } - - static int mtk_cpufreq_init(struct cpufreq_policy *policy) diff --git a/target/linux/mediatek/patches-5.15/350-12-cpufreq-mediatek-Fix-potential-deadlock-problem-in-m.patch b/target/linux/mediatek/patches-5.15/350-12-cpufreq-mediatek-Fix-potential-deadlock-problem-in-m.patch deleted file mode 100644 index 76bd795c00..0000000000 --- a/target/linux/mediatek/patches-5.15/350-12-cpufreq-mediatek-Fix-potential-deadlock-problem-in-m.patch +++ /dev/null @@ -1,43 +0,0 @@ -From 6a1bd7cf4ed7a1948f564aaf16d34b7352c0029b Mon Sep 17 00:00:00 2001 -From: Wan Jiabing -Date: Tue, 10 May 2022 17:05:31 +0800 -Subject: [PATCH 12/21] cpufreq: mediatek: Fix potential deadlock problem in - mtk_cpufreq_set_target - -Fix following coccichek error: -./drivers/cpufreq/mediatek-cpufreq.c:199:2-8: preceding lock on line -./drivers/cpufreq/mediatek-cpufreq.c:208:2-8: preceding lock on line - -mutex_lock is acquired but not released before return. -Use 'goto out' to help releasing the mutex_lock. - -Fixes: c210063b40ac ("cpufreq: mediatek: Add opp notification support") -Signed-off-by: Wan Jiabing -Reviewed-by: Rex-BC Chen -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 6 ++++-- - 1 file changed, 4 insertions(+), 2 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -196,7 +196,8 @@ static int mtk_cpufreq_set_target(struct - - if (pre_vproc < 0) { - dev_err(cpu_dev, "invalid Vproc value: %d\n", pre_vproc); -- return pre_vproc; -+ ret = pre_vproc; -+ goto out; - } - - freq_hz = freq_table[index].frequency * 1000; -@@ -205,7 +206,8 @@ static int mtk_cpufreq_set_target(struct - if (IS_ERR(opp)) { - dev_err(cpu_dev, "cpu%d: failed to find OPP for %ld\n", - policy->cpu, freq_hz); -- return PTR_ERR(opp); -+ ret = PTR_ERR(opp); -+ goto out; - } - vproc = dev_pm_opp_get_voltage(opp); - dev_pm_opp_put(opp); diff --git a/target/linux/mediatek/patches-5.15/350-13-cpufreq-mediatek-Link-CCI-device-to-CPU.patch b/target/linux/mediatek/patches-5.15/350-13-cpufreq-mediatek-Link-CCI-device-to-CPU.patch deleted file mode 100644 index eeaa466c32..0000000000 --- a/target/linux/mediatek/patches-5.15/350-13-cpufreq-mediatek-Link-CCI-device-to-CPU.patch +++ /dev/null @@ -1,188 +0,0 @@ -From 15aaf74fb734a3e69b10d00b97b322711b81e222 Mon Sep 17 00:00:00 2001 -From: Rex-BC Chen -Date: Thu, 5 May 2022 19:52:22 +0800 -Subject: [PATCH 13/21] cpufreq: mediatek: Link CCI device to CPU - -In some MediaTek SoCs, like MT8183, CPU and CCI share the same power -supplies. Cpufreq needs to check if CCI devfreq exists and wait until -CCI devfreq ready before scaling frequency. - -Before CCI devfreq is ready, we record the voltage when booting to -kernel and use the max(cpu target voltage, booting voltage) to -prevent cpufreq adjust to the lower voltage which will cause the CCI -crash because of high frequency and low voltage. - -- Add is_ccifreq_ready() to link CCI device to CPI, and CPU will start - DVFS when CCI is ready. -- Add platform data for MT8183. - -Signed-off-by: Jia-Wei Chang -Signed-off-by: Rex-BC Chen -Reviewed-by: AngeloGioacchino Del Regno -Reviewed-by: Kevin Hilman -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 82 +++++++++++++++++++++++++++++- - 1 file changed, 81 insertions(+), 1 deletion(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -22,6 +22,7 @@ struct mtk_cpufreq_platform_data { - int proc_max_volt; - int sram_min_volt; - int sram_max_volt; -+ bool ccifreq_supported; - }; - - /* -@@ -38,6 +39,7 @@ struct mtk_cpufreq_platform_data { - struct mtk_cpu_dvfs_info { - struct cpumask cpus; - struct device *cpu_dev; -+ struct device *cci_dev; - struct regulator *proc_reg; - struct regulator *sram_reg; - struct clk *cpu_clk; -@@ -45,6 +47,7 @@ struct mtk_cpu_dvfs_info { - struct list_head list_head; - int intermediate_voltage; - bool need_voltage_tracking; -+ int vproc_on_boot; - int pre_vproc; - /* Avoid race condition for regulators between notify and policy */ - struct mutex reg_lock; -@@ -53,6 +56,7 @@ struct mtk_cpu_dvfs_info { - unsigned long current_freq; - const struct mtk_cpufreq_platform_data *soc_data; - int vtrack_max; -+ bool ccifreq_bound; - }; - - static struct platform_device *cpufreq_pdev; -@@ -171,6 +175,28 @@ static int mtk_cpufreq_set_voltage(struc - return ret; - } - -+static bool is_ccifreq_ready(struct mtk_cpu_dvfs_info *info) -+{ -+ struct device_link *sup_link; -+ -+ if (info->ccifreq_bound) -+ return true; -+ -+ sup_link = device_link_add(info->cpu_dev, info->cci_dev, -+ DL_FLAG_AUTOREMOVE_CONSUMER); -+ if (!sup_link) { -+ dev_err(info->cpu_dev, "cpu%d: sup_link is NULL\n", info->opp_cpu); -+ return false; -+ } -+ -+ if (sup_link->supplier->links.status != DL_DEV_DRIVER_BOUND) -+ return false; -+ -+ info->ccifreq_bound = true; -+ -+ return true; -+} -+ - static int mtk_cpufreq_set_target(struct cpufreq_policy *policy, - unsigned int index) - { -@@ -213,6 +239,14 @@ static int mtk_cpufreq_set_target(struct - dev_pm_opp_put(opp); - - /* -+ * If MediaTek cci is supported but is not ready, we will use the value -+ * of max(target cpu voltage, booting voltage) to prevent high freqeuncy -+ * low voltage crash. -+ */ -+ if (info->soc_data->ccifreq_supported && !is_ccifreq_ready(info)) -+ vproc = max(vproc, info->vproc_on_boot); -+ -+ /* - * If the new voltage or the intermediate voltage is higher than the - * current voltage, scale up voltage first. - */ -@@ -333,6 +367,23 @@ static int mtk_cpufreq_opp_notifier(stru - return notifier_from_errno(ret); - } - -+static struct device *of_get_cci(struct device *cpu_dev) -+{ -+ struct device_node *np; -+ struct platform_device *pdev; -+ -+ np = of_parse_phandle(cpu_dev->of_node, "mediatek,cci", 0); -+ if (IS_ERR_OR_NULL(np)) -+ return NULL; -+ -+ pdev = of_find_device_by_node(np); -+ of_node_put(np); -+ if (IS_ERR_OR_NULL(pdev)) -+ return NULL; -+ -+ return &pdev->dev; -+} -+ - static int mtk_cpu_dvfs_info_init(struct mtk_cpu_dvfs_info *info, int cpu) - { - struct device *cpu_dev; -@@ -347,6 +398,16 @@ static int mtk_cpu_dvfs_info_init(struct - } - info->cpu_dev = cpu_dev; - -+ info->ccifreq_bound = false; -+ if (info->soc_data->ccifreq_supported) { -+ info->cci_dev = of_get_cci(info->cpu_dev); -+ if (IS_ERR_OR_NULL(info->cci_dev)) { -+ ret = PTR_ERR(info->cci_dev); -+ dev_err(cpu_dev, "cpu%d: failed to get cci device\n", cpu); -+ return -ENODEV; -+ } -+ } -+ - info->cpu_clk = clk_get(cpu_dev, "cpu"); - if (IS_ERR(info->cpu_clk)) { - ret = PTR_ERR(info->cpu_clk); -@@ -410,6 +471,15 @@ static int mtk_cpu_dvfs_info_init(struct - if (ret) - goto out_disable_mux_clock; - -+ if (info->soc_data->ccifreq_supported) { -+ info->vproc_on_boot = regulator_get_voltage(info->proc_reg); -+ if (info->vproc_on_boot < 0) { -+ dev_err(info->cpu_dev, -+ "invalid Vproc value: %d\n", info->vproc_on_boot); -+ goto out_disable_inter_clock; -+ } -+ } -+ - /* Search a safe voltage for intermediate frequency. */ - rate = clk_get_rate(info->inter_clk); - opp = dev_pm_opp_find_freq_ceil(cpu_dev, &rate); -@@ -617,6 +687,16 @@ static const struct mtk_cpufreq_platform - .proc_max_volt = 1150000, - .sram_min_volt = 0, - .sram_max_volt = 1150000, -+ .ccifreq_supported = false, -+}; -+ -+static const struct mtk_cpufreq_platform_data mt8183_platform_data = { -+ .min_volt_shift = 100000, -+ .max_volt_shift = 200000, -+ .proc_max_volt = 1150000, -+ .sram_min_volt = 0, -+ .sram_max_volt = 1150000, -+ .ccifreq_supported = true, - }; - - /* List of machines supported by this driver */ -@@ -629,7 +709,7 @@ static const struct of_device_id mtk_cpu - { .compatible = "mediatek,mt817x", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt8173", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt8176", .data = &mt2701_platform_data }, -- { .compatible = "mediatek,mt8183", .data = &mt2701_platform_data }, -+ { .compatible = "mediatek,mt8183", .data = &mt8183_platform_data }, - { .compatible = "mediatek,mt8365", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt8516", .data = &mt2701_platform_data }, - { } diff --git a/target/linux/mediatek/patches-5.15/350-14-cpufreq-mediatek-Add-support-for-MT8186.patch b/target/linux/mediatek/patches-5.15/350-14-cpufreq-mediatek-Add-support-for-MT8186.patch deleted file mode 100644 index 31000cfbe0..0000000000 --- a/target/linux/mediatek/patches-5.15/350-14-cpufreq-mediatek-Add-support-for-MT8186.patch +++ /dev/null @@ -1,42 +0,0 @@ -From b6be0baa6615afc65c3963adab674e36af1d4d5f Mon Sep 17 00:00:00 2001 -From: Jia-Wei Chang -Date: Thu, 5 May 2022 19:52:23 +0800 -Subject: [PATCH 14/21] cpufreq: mediatek: Add support for MT8186 - -The platform data of MT8186 is different from previous MediaTek SoCs, -so we add a new compatible and platform data for it. - -Signed-off-by: Jia-Wei Chang -Signed-off-by: Rex-BC Chen -Reviewed-by: AngeloGioacchino Del Regno -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 10 ++++++++++ - 1 file changed, 10 insertions(+) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -699,6 +699,15 @@ static const struct mtk_cpufreq_platform - .ccifreq_supported = true, - }; - -+static const struct mtk_cpufreq_platform_data mt8186_platform_data = { -+ .min_volt_shift = 100000, -+ .max_volt_shift = 250000, -+ .proc_max_volt = 1118750, -+ .sram_min_volt = 850000, -+ .sram_max_volt = 1118750, -+ .ccifreq_supported = true, -+}; -+ - /* List of machines supported by this driver */ - static const struct of_device_id mtk_cpufreq_machines[] __initconst = { - { .compatible = "mediatek,mt2701", .data = &mt2701_platform_data }, -@@ -710,6 +719,7 @@ static const struct of_device_id mtk_cpu - { .compatible = "mediatek,mt8173", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt8176", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt8183", .data = &mt8183_platform_data }, -+ { .compatible = "mediatek,mt8186", .data = &mt8186_platform_data }, - { .compatible = "mediatek,mt8365", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt8516", .data = &mt2701_platform_data }, - { } diff --git a/target/linux/mediatek/patches-5.15/350-15-cpufreq-mediatek-Handle-sram-regulator-probe-deferra.patch b/target/linux/mediatek/patches-5.15/350-15-cpufreq-mediatek-Handle-sram-regulator-probe-deferra.patch deleted file mode 100644 index c0137894c9..0000000000 --- a/target/linux/mediatek/patches-5.15/350-15-cpufreq-mediatek-Handle-sram-regulator-probe-deferra.patch +++ /dev/null @@ -1,35 +0,0 @@ -From 75d19b24aa3203d6c78e4c431c2cc07157ce12fe Mon Sep 17 00:00:00 2001 -From: AngeloGioacchino Del Regno -Date: Wed, 13 Jul 2022 13:15:36 +0200 -Subject: [PATCH 15/21] cpufreq: mediatek: Handle sram regulator probe deferral - -If the regulator_get_optional() call for the SRAM regulator returns -a probe deferral, we must bail out and retry probing later: failing -to do this will produce unstabilities on platforms requiring the -handling for this regulator. - -Fixes: ffa7bdf7f344 ("cpufreq: mediatek: Make sram regulator optional") -Signed-off-by: AngeloGioacchino Del Regno -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 8 ++++++-- - 1 file changed, 6 insertions(+), 2 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -439,9 +439,13 @@ static int mtk_cpu_dvfs_info_init(struct - - /* Both presence and absence of sram regulator are valid cases. */ - info->sram_reg = regulator_get_optional(cpu_dev, "sram"); -- if (IS_ERR(info->sram_reg)) -+ if (IS_ERR(info->sram_reg)) { -+ ret = PTR_ERR(info->sram_reg); -+ if (ret == -EPROBE_DEFER) -+ goto out_free_resources; -+ - info->sram_reg = NULL; -- else { -+ } else { - ret = regulator_enable(info->sram_reg); - if (ret) { - dev_warn(cpu_dev, "cpu%d: failed to enable vsram\n", cpu); diff --git a/target/linux/mediatek/patches-5.15/350-16-cpufreq-mediatek-fix-error-return-code-in-mtk_cpu_dv.patch b/target/linux/mediatek/patches-5.15/350-16-cpufreq-mediatek-fix-error-return-code-in-mtk_cpu_dv.patch deleted file mode 100644 index 45c4477ff1..0000000000 --- a/target/linux/mediatek/patches-5.15/350-16-cpufreq-mediatek-fix-error-return-code-in-mtk_cpu_dv.patch +++ /dev/null @@ -1,29 +0,0 @@ -From dd1174c21dacacd6c0129c1dabc5decad35c02c2 Mon Sep 17 00:00:00 2001 -From: Yang Yingliang -Date: Tue, 17 May 2022 21:34:50 +0800 -Subject: [PATCH 16/21] cpufreq: mediatek: fix error return code in - mtk_cpu_dvfs_info_init() - -If regulator_get_voltage() fails, it should return the error code in -mtk_cpu_dvfs_info_init(). - -Fixes: 0daa47325bae ("cpufreq: mediatek: Link CCI device to CPU") -Reported-by: Hulk Robot -Signed-off-by: Yang Yingliang -Reviewed-by: AngeloGioacchino Del Regno -Reviewed-by: Rex-BC Chen -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 1 + - 1 file changed, 1 insertion(+) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -478,6 +478,7 @@ static int mtk_cpu_dvfs_info_init(struct - if (info->soc_data->ccifreq_supported) { - info->vproc_on_boot = regulator_get_voltage(info->proc_reg); - if (info->vproc_on_boot < 0) { -+ ret = info->vproc_on_boot; - dev_err(info->cpu_dev, - "invalid Vproc value: %d\n", info->vproc_on_boot); - goto out_disable_inter_clock; diff --git a/target/linux/mediatek/patches-5.15/350-17-cpufreq-mediatek-fix-passing-zero-to-PTR_ERR.patch b/target/linux/mediatek/patches-5.15/350-17-cpufreq-mediatek-fix-passing-zero-to-PTR_ERR.patch deleted file mode 100644 index 557d02b822..0000000000 --- a/target/linux/mediatek/patches-5.15/350-17-cpufreq-mediatek-fix-passing-zero-to-PTR_ERR.patch +++ /dev/null @@ -1,47 +0,0 @@ -From 230a74d459244411db91bfd678f17fcf7aedfcd0 Mon Sep 17 00:00:00 2001 -From: Jia-Wei Chang -Date: Fri, 24 Mar 2023 18:11:27 +0800 -Subject: [PATCH 17/21] cpufreq: mediatek: fix passing zero to 'PTR_ERR' - -In order to prevent passing zero to 'PTR_ERR' in -mtk_cpu_dvfs_info_init(), we fix the return value of of_get_cci() using -error pointer by explicitly casting error number. - -Signed-off-by: Jia-Wei Chang -Fixes: 0daa47325bae ("cpufreq: mediatek: Link CCI device to CPU") -Reported-by: Dan Carpenter -Reviewed-by: AngeloGioacchino Del Regno -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 10 +++++----- - 1 file changed, 5 insertions(+), 5 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -373,13 +373,13 @@ static struct device *of_get_cci(struct - struct platform_device *pdev; - - np = of_parse_phandle(cpu_dev->of_node, "mediatek,cci", 0); -- if (IS_ERR_OR_NULL(np)) -- return NULL; -+ if (!np) -+ return ERR_PTR(-ENODEV); - - pdev = of_find_device_by_node(np); - of_node_put(np); -- if (IS_ERR_OR_NULL(pdev)) -- return NULL; -+ if (!pdev) -+ return ERR_PTR(-ENODEV); - - return &pdev->dev; - } -@@ -401,7 +401,7 @@ static int mtk_cpu_dvfs_info_init(struct - info->ccifreq_bound = false; - if (info->soc_data->ccifreq_supported) { - info->cci_dev = of_get_cci(info->cpu_dev); -- if (IS_ERR_OR_NULL(info->cci_dev)) { -+ if (IS_ERR(info->cci_dev)) { - ret = PTR_ERR(info->cci_dev); - dev_err(cpu_dev, "cpu%d: failed to get cci device\n", cpu); - return -ENODEV; diff --git a/target/linux/mediatek/patches-5.15/350-18-cpufreq-mediatek-fix-KP-caused-by-handler-usage-afte.patch b/target/linux/mediatek/patches-5.15/350-18-cpufreq-mediatek-fix-KP-caused-by-handler-usage-afte.patch deleted file mode 100644 index 61531d38ad..0000000000 --- a/target/linux/mediatek/patches-5.15/350-18-cpufreq-mediatek-fix-KP-caused-by-handler-usage-afte.patch +++ /dev/null @@ -1,149 +0,0 @@ -From fced531b7c7e18192e7982637c8e8f20c29aad64 Mon Sep 17 00:00:00 2001 -From: Jia-Wei Chang -Date: Fri, 24 Mar 2023 18:11:28 +0800 -Subject: [PATCH 18/21] cpufreq: mediatek: fix KP caused by handler usage after - regulator_put/clk_put - -Any kind of failure in mtk_cpu_dvfs_info_init() will lead to calling -regulator_put() or clk_put() and the KP will occur since the regulator/clk -handlers are used after released in mtk_cpu_dvfs_info_release(). - -To prevent the usage after regulator_put()/clk_put(), the regulator/clk -handlers are addressed in a way of "Free the Last Thing Style". - -Signed-off-by: Jia-Wei Chang -Fixes: 4b9ceb757bbb ("cpufreq: mediatek: Enable clocks and regulators") -Suggested-by: AngeloGioacchino Del Regno -Suggested-by: Dan Carpenter -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 62 +++++++++++++++--------------- - 1 file changed, 30 insertions(+), 32 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -420,7 +420,7 @@ static int mtk_cpu_dvfs_info_init(struct - ret = PTR_ERR(info->inter_clk); - dev_err_probe(cpu_dev, ret, - "cpu%d: failed to get intermediate clk\n", cpu); -- goto out_free_resources; -+ goto out_free_mux_clock; - } - - info->proc_reg = regulator_get_optional(cpu_dev, "proc"); -@@ -428,13 +428,13 @@ static int mtk_cpu_dvfs_info_init(struct - ret = PTR_ERR(info->proc_reg); - dev_err_probe(cpu_dev, ret, - "cpu%d: failed to get proc regulator\n", cpu); -- goto out_free_resources; -+ goto out_free_inter_clock; - } - - ret = regulator_enable(info->proc_reg); - if (ret) { - dev_warn(cpu_dev, "cpu%d: failed to enable vproc\n", cpu); -- goto out_free_resources; -+ goto out_free_proc_reg; - } - - /* Both presence and absence of sram regulator are valid cases. */ -@@ -442,14 +442,14 @@ static int mtk_cpu_dvfs_info_init(struct - if (IS_ERR(info->sram_reg)) { - ret = PTR_ERR(info->sram_reg); - if (ret == -EPROBE_DEFER) -- goto out_free_resources; -+ goto out_disable_proc_reg; - - info->sram_reg = NULL; - } else { - ret = regulator_enable(info->sram_reg); - if (ret) { - dev_warn(cpu_dev, "cpu%d: failed to enable vsram\n", cpu); -- goto out_free_resources; -+ goto out_free_sram_reg; - } - } - -@@ -458,13 +458,13 @@ static int mtk_cpu_dvfs_info_init(struct - if (ret) { - dev_err(cpu_dev, - "cpu%d: failed to get OPP-sharing information\n", cpu); -- goto out_free_resources; -+ goto out_disable_sram_reg; - } - - ret = dev_pm_opp_of_cpumask_add_table(&info->cpus); - if (ret) { - dev_warn(cpu_dev, "cpu%d: no OPP table\n", cpu); -- goto out_free_resources; -+ goto out_disable_sram_reg; - } - - ret = clk_prepare_enable(info->cpu_clk); -@@ -533,43 +533,41 @@ out_disable_mux_clock: - out_free_opp_table: - dev_pm_opp_of_cpumask_remove_table(&info->cpus); - --out_free_resources: -- if (regulator_is_enabled(info->proc_reg)) -- regulator_disable(info->proc_reg); -- if (info->sram_reg && regulator_is_enabled(info->sram_reg)) -+out_disable_sram_reg: -+ if (info->sram_reg) - regulator_disable(info->sram_reg); - -- if (!IS_ERR(info->proc_reg)) -- regulator_put(info->proc_reg); -- if (!IS_ERR(info->sram_reg)) -+out_free_sram_reg: -+ if (info->sram_reg) - regulator_put(info->sram_reg); -- if (!IS_ERR(info->cpu_clk)) -- clk_put(info->cpu_clk); -- if (!IS_ERR(info->inter_clk)) -- clk_put(info->inter_clk); -+ -+out_disable_proc_reg: -+ regulator_disable(info->proc_reg); -+ -+out_free_proc_reg: -+ regulator_put(info->proc_reg); -+ -+out_free_inter_clock: -+ clk_put(info->inter_clk); -+ -+out_free_mux_clock: -+ clk_put(info->cpu_clk); - - return ret; - } - - static void mtk_cpu_dvfs_info_release(struct mtk_cpu_dvfs_info *info) - { -- if (!IS_ERR(info->proc_reg)) { -- regulator_disable(info->proc_reg); -- regulator_put(info->proc_reg); -- } -- if (!IS_ERR(info->sram_reg)) { -+ regulator_disable(info->proc_reg); -+ regulator_put(info->proc_reg); -+ if (info->sram_reg) { - regulator_disable(info->sram_reg); - regulator_put(info->sram_reg); - } -- if (!IS_ERR(info->cpu_clk)) { -- clk_disable_unprepare(info->cpu_clk); -- clk_put(info->cpu_clk); -- } -- if (!IS_ERR(info->inter_clk)) { -- clk_disable_unprepare(info->inter_clk); -- clk_put(info->inter_clk); -- } -- -+ clk_disable_unprepare(info->cpu_clk); -+ clk_put(info->cpu_clk); -+ clk_disable_unprepare(info->inter_clk); -+ clk_put(info->inter_clk); - dev_pm_opp_of_cpumask_remove_table(&info->cpus); - dev_pm_opp_unregister_notifier(info->cpu_dev, &info->opp_nb); - } diff --git a/target/linux/mediatek/patches-5.15/350-19-cpufreq-mediatek-raise-proc-sram-max-voltage-for-MT8.patch b/target/linux/mediatek/patches-5.15/350-19-cpufreq-mediatek-raise-proc-sram-max-voltage-for-MT8.patch deleted file mode 100644 index 2b7d229f1c..0000000000 --- a/target/linux/mediatek/patches-5.15/350-19-cpufreq-mediatek-raise-proc-sram-max-voltage-for-MT8.patch +++ /dev/null @@ -1,55 +0,0 @@ -From 24bc42a2d44cb821818717a5c607270921ec5d20 Mon Sep 17 00:00:00 2001 -From: Jia-Wei Chang -Date: Fri, 24 Mar 2023 18:11:29 +0800 -Subject: [PATCH 19/21] cpufreq: mediatek: raise proc/sram max voltage for - MT8516 - -Since the upper boundary of proc/sram voltage of MT8516 is 1300 mV, -which is greater than the value of MT2701 1150 mV, we fix it by adding -the corresponding platform data and specify proc/sram_max_volt to -support MT8516. - -Signed-off-by: Jia-Wei Chang -Fixes: ead858bd128d ("cpufreq: mediatek: Move voltage limits to platform data") -Fixes: 6a17b3876bc8 ("cpufreq: mediatek: Refine mtk_cpufreq_voltage_tracking()") -Reported-by: Nick Hainke -Reviewed-by: AngeloGioacchino Del Regno -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 13 +++++++++++-- - 1 file changed, 11 insertions(+), 2 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -711,20 +711,29 @@ static const struct mtk_cpufreq_platform - .ccifreq_supported = true, - }; - -+static const struct mtk_cpufreq_platform_data mt8516_platform_data = { -+ .min_volt_shift = 100000, -+ .max_volt_shift = 200000, -+ .proc_max_volt = 1310000, -+ .sram_min_volt = 0, -+ .sram_max_volt = 1310000, -+ .ccifreq_supported = false, -+}; -+ - /* List of machines supported by this driver */ - static const struct of_device_id mtk_cpufreq_machines[] __initconst = { - { .compatible = "mediatek,mt2701", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt2712", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt7622", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt7623", .data = &mt2701_platform_data }, -- { .compatible = "mediatek,mt8167", .data = &mt2701_platform_data }, -+ { .compatible = "mediatek,mt8167", .data = &mt8516_platform_data }, - { .compatible = "mediatek,mt817x", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt8173", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt8176", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt8183", .data = &mt8183_platform_data }, - { .compatible = "mediatek,mt8186", .data = &mt8186_platform_data }, - { .compatible = "mediatek,mt8365", .data = &mt2701_platform_data }, -- { .compatible = "mediatek,mt8516", .data = &mt2701_platform_data }, -+ { .compatible = "mediatek,mt8516", .data = &mt8516_platform_data }, - { } - }; - MODULE_DEVICE_TABLE(of, mtk_cpufreq_machines); diff --git a/target/linux/mediatek/patches-5.15/350-20-cpufreq-mediatek-Raise-proc-and-sram-max-voltage-for.patch b/target/linux/mediatek/patches-5.15/350-20-cpufreq-mediatek-Raise-proc-and-sram-max-voltage-for.patch deleted file mode 100644 index 2de8eb6394..0000000000 --- a/target/linux/mediatek/patches-5.15/350-20-cpufreq-mediatek-Raise-proc-and-sram-max-voltage-for.patch +++ /dev/null @@ -1,58 +0,0 @@ -From fe6ef09358dc0cfead9d383a8676fbe7a40fcef7 Mon Sep 17 00:00:00 2001 -From: AngeloGioacchino Del Regno -Date: Fri, 24 Mar 2023 18:11:30 +0800 -Subject: [PATCH 20/21] cpufreq: mediatek: Raise proc and sram max voltage for - MT7622/7623 - -During the addition of SRAM voltage tracking for CCI scaling, this -driver got some voltage limits set for the vtrack algorithm: these -were moved to platform data first, then enforced in a later commit -6a17b3876bc8 ("cpufreq: mediatek: Refine mtk_cpufreq_voltage_tracking()") -using these as max values for the regulator_set_voltage() calls. - -In this case, the vsram/vproc constraints for MT7622 and MT7623 -were supposed to be the same as MT2701 (and a number of other SoCs), -but that turned out to be a mistake because the aforementioned two -SoCs' maximum voltage for both VPROC and VPROC_SRAM is 1.36V. - -Fix that by adding new platform data for MT7622/7623 declaring the -right {proc,sram}_max_volt parameter. - -Fixes: ead858bd128d ("cpufreq: mediatek: Move voltage limits to platform data") -Fixes: 6a17b3876bc8 ("cpufreq: mediatek: Refine mtk_cpufreq_voltage_tracking()") -Signed-off-by: AngeloGioacchino Del Regno -Signed-off-by: Jia-Wei Chang -Signed-off-by: Viresh Kumar ---- - drivers/cpufreq/mediatek-cpufreq.c | 13 +++++++++++-- - 1 file changed, 11 insertions(+), 2 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -693,6 +693,15 @@ static const struct mtk_cpufreq_platform - .ccifreq_supported = false, - }; - -+static const struct mtk_cpufreq_platform_data mt7622_platform_data = { -+ .min_volt_shift = 100000, -+ .max_volt_shift = 200000, -+ .proc_max_volt = 1360000, -+ .sram_min_volt = 0, -+ .sram_max_volt = 1360000, -+ .ccifreq_supported = false, -+}; -+ - static const struct mtk_cpufreq_platform_data mt8183_platform_data = { - .min_volt_shift = 100000, - .max_volt_shift = 200000, -@@ -724,8 +733,8 @@ static const struct mtk_cpufreq_platform - static const struct of_device_id mtk_cpufreq_machines[] __initconst = { - { .compatible = "mediatek,mt2701", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt2712", .data = &mt2701_platform_data }, -- { .compatible = "mediatek,mt7622", .data = &mt2701_platform_data }, -- { .compatible = "mediatek,mt7623", .data = &mt2701_platform_data }, -+ { .compatible = "mediatek,mt7622", .data = &mt7622_platform_data }, -+ { .compatible = "mediatek,mt7623", .data = &mt7622_platform_data }, - { .compatible = "mediatek,mt8167", .data = &mt8516_platform_data }, - { .compatible = "mediatek,mt817x", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt8173", .data = &mt2701_platform_data }, diff --git a/target/linux/mediatek/patches-5.15/350-21-cpufreq-mediatek-Add-support-for-MT7988.patch b/target/linux/mediatek/patches-5.15/350-21-cpufreq-mediatek-Add-support-for-MT7988.patch deleted file mode 100644 index 6acd3d607f..0000000000 --- a/target/linux/mediatek/patches-5.15/350-21-cpufreq-mediatek-Add-support-for-MT7988.patch +++ /dev/null @@ -1,41 +0,0 @@ -From 4983a1517e7ddbc6f53fc07607e4ebeb51412843 Mon Sep 17 00:00:00 2001 -From: Sam Shih -Date: Tue, 28 Feb 2023 19:59:22 +0800 -Subject: [PATCH 21/21] cpufreq: mediatek: Add support for MT7988 - -This add cpufreq support for mediatek MT7988 SoC. - -The platform data of MT7988 is different from previous MediaTek SoCs, -so we add a new compatible and platform data for it. - -Signed-off-by: Sam Shih ---- - drivers/cpufreq/mediatek-cpufreq.c | 10 ++++++++++ - 1 file changed, 10 insertions(+) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -702,6 +702,15 @@ static const struct mtk_cpufreq_platform - .ccifreq_supported = false, - }; - -+static const struct mtk_cpufreq_platform_data mt7988_platform_data = { -+ .min_volt_shift = 100000, -+ .max_volt_shift = 200000, -+ .proc_max_volt = 900000, -+ .sram_min_volt = 0, -+ .sram_max_volt = 1150000, -+ .ccifreq_supported = true, -+}; -+ - static const struct mtk_cpufreq_platform_data mt8183_platform_data = { - .min_volt_shift = 100000, - .max_volt_shift = 200000, -@@ -735,6 +744,7 @@ static const struct of_device_id mtk_cpu - { .compatible = "mediatek,mt2712", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt7622", .data = &mt7622_platform_data }, - { .compatible = "mediatek,mt7623", .data = &mt7622_platform_data }, -+ { .compatible = "mediatek,mt7988", .data = &mt7988_platform_data }, - { .compatible = "mediatek,mt8167", .data = &mt8516_platform_data }, - { .compatible = "mediatek,mt817x", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt8173", .data = &mt2701_platform_data }, diff --git a/target/linux/mediatek/patches-5.15/351-cpufreq-mediatek-correct-voltages-for-MT7622-and-MT7.patch b/target/linux/mediatek/patches-5.15/351-cpufreq-mediatek-correct-voltages-for-MT7622-and-MT7.patch deleted file mode 100644 index 6ab05b897c..0000000000 --- a/target/linux/mediatek/patches-5.15/351-cpufreq-mediatek-correct-voltages-for-MT7622-and-MT7.patch +++ /dev/null @@ -1,53 +0,0 @@ -From e7697814c142c99f470c3458d49e41b25a575f23 Mon Sep 17 00:00:00 2001 -From: Daniel Golle -Date: Fri, 26 May 2023 10:31:40 +0100 -Subject: [PATCH] cpufreq: mediatek: correct voltages for MT7622 and MT7623 - -The MT6380 regulator typically used together with MT7622 does not -support the current maximum processor and SRAM voltage in the cpufreq -driver (1360000uV). -For MT7622 limit processor and SRAM supply voltages to 1350000uV to -avoid having the tracking algorithm request unsupported voltages from -the regulator. - -On MT7623 there is no separate SRAM supply and the maximum voltage used -is 1300000uV. Create dedicated platform data for MT7623 to cover that -case as well. - -Fixes: 0883426fd07e3 ("cpufreq: mediatek: Raise proc and sram max voltage for MT7622/7623") -Suggested-by: Jia-wei Chang -Signed-off-by: Daniel Golle ---- - drivers/cpufreq/mediatek-cpufreq.c | 13 ++++++++++--- - 1 file changed, 10 insertions(+), 3 deletions(-) - ---- a/drivers/cpufreq/mediatek-cpufreq.c -+++ b/drivers/cpufreq/mediatek-cpufreq.c -@@ -696,9 +696,16 @@ static const struct mtk_cpufreq_platform - static const struct mtk_cpufreq_platform_data mt7622_platform_data = { - .min_volt_shift = 100000, - .max_volt_shift = 200000, -- .proc_max_volt = 1360000, -+ .proc_max_volt = 1350000, - .sram_min_volt = 0, -- .sram_max_volt = 1360000, -+ .sram_max_volt = 1350000, -+ .ccifreq_supported = false, -+}; -+ -+static const struct mtk_cpufreq_platform_data mt7623_platform_data = { -+ .min_volt_shift = 100000, -+ .max_volt_shift = 200000, -+ .proc_max_volt = 1300000, - .ccifreq_supported = false, - }; - -@@ -743,7 +750,7 @@ static const struct of_device_id mtk_cpu - { .compatible = "mediatek,mt2701", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt2712", .data = &mt2701_platform_data }, - { .compatible = "mediatek,mt7622", .data = &mt7622_platform_data }, -- { .compatible = "mediatek,mt7623", .data = &mt7622_platform_data }, -+ { .compatible = "mediatek,mt7623", .data = &mt7623_platform_data }, - { .compatible = "mediatek,mt7988", .data = &mt7988_platform_data }, - { .compatible = "mediatek,mt8167", .data = &mt8516_platform_data }, - { .compatible = "mediatek,mt817x", .data = &mt2701_platform_data }, diff --git a/target/linux/mediatek/patches-5.15/400-crypto-add-eip97-inside-secure-support.patch b/target/linux/mediatek/patches-5.15/400-crypto-add-eip97-inside-secure-support.patch deleted file mode 100644 index 25ca9485e4..0000000000 --- a/target/linux/mediatek/patches-5.15/400-crypto-add-eip97-inside-secure-support.patch +++ /dev/null @@ -1,27 +0,0 @@ ---- a/drivers/crypto/inside-secure/safexcel.c -+++ b/drivers/crypto/inside-secure/safexcel.c -@@ -600,6 +600,14 @@ static int safexcel_hw_init(struct safex - val |= EIP197_MST_CTRL_TX_MAX_CMD(5); - writel(val, EIP197_HIA_AIC(priv) + EIP197_HIA_MST_CTRL); - } -+ /* -+ * Set maximum number of TX commands to 2^4 = 16 for EIP97 HW2.1/HW2.3 -+ */ -+ else { -+ val = 0; -+ val |= EIP97_MST_CTRL_TX_MAX_CMD(4); -+ writel(val, EIP197_HIA_AIC(priv) + EIP197_HIA_MST_CTRL); -+ } - - /* Configure wr/rd cache values */ - writel(EIP197_MST_CTRL_RD_CACHE(RD_CACHE_4BITS) | ---- a/drivers/crypto/inside-secure/safexcel.h -+++ b/drivers/crypto/inside-secure/safexcel.h -@@ -315,6 +315,7 @@ - #define EIP197_MST_CTRL_RD_CACHE(n) (((n) & 0xf) << 0) - #define EIP197_MST_CTRL_WD_CACHE(n) (((n) & 0xf) << 4) - #define EIP197_MST_CTRL_TX_MAX_CMD(n) (((n) & 0xf) << 20) -+#define EIP97_MST_CTRL_TX_MAX_CMD(n) (((n) & 0xf) << 4) - #define EIP197_MST_CTRL_BYTE_SWAP BIT(24) - #define EIP197_MST_CTRL_NO_BYTE_SWAP BIT(25) - #define EIP197_MST_CTRL_BYTE_SWAP_BITS GENMASK(25, 24) diff --git a/target/linux/mediatek/patches-5.15/401-crypto-fix-eip97-cache-incoherent.patch b/target/linux/mediatek/patches-5.15/401-crypto-fix-eip97-cache-incoherent.patch deleted file mode 100644 index 186c66f687..0000000000 --- a/target/linux/mediatek/patches-5.15/401-crypto-fix-eip97-cache-incoherent.patch +++ /dev/null @@ -1,26 +0,0 @@ ---- a/drivers/crypto/inside-secure/safexcel.h -+++ b/drivers/crypto/inside-secure/safexcel.h -@@ -737,6 +737,9 @@ enum safexcel_eip_version { - /* Priority we use for advertising our algorithms */ - #define SAFEXCEL_CRA_PRIORITY 300 - -+/* System cache line size */ -+#define SYSTEM_CACHELINE_SIZE 64 -+ - /* SM3 digest result for zero length message */ - #define EIP197_SM3_ZEROM_HASH "\x1A\xB2\x1D\x83\x55\xCF\xA1\x7F" \ - "\x8E\x61\x19\x48\x31\xE8\x1A\x8F" \ ---- a/drivers/crypto/inside-secure/safexcel_hash.c -+++ b/drivers/crypto/inside-secure/safexcel_hash.c -@@ -55,9 +55,9 @@ struct safexcel_ahash_req { - u8 block_sz; /* block size, only set once */ - u8 digest_sz; /* output digest size, only set once */ - __le32 state[SHA3_512_BLOCK_SIZE / -- sizeof(__le32)] __aligned(sizeof(__le32)); -+ sizeof(__le32)] __aligned(SYSTEM_CACHELINE_SIZE); - -- u64 len; -+ u64 len __aligned(SYSTEM_CACHELINE_SIZE); - u64 processed; - - u8 cache[HASH_CACHE_SIZE] __aligned(sizeof(u32)); diff --git a/target/linux/mediatek/patches-5.15/405-mt7986-trng-add-rng-support.patch b/target/linux/mediatek/patches-5.15/405-mt7986-trng-add-rng-support.patch deleted file mode 100644 index 332f17bae7..0000000000 --- a/target/linux/mediatek/patches-5.15/405-mt7986-trng-add-rng-support.patch +++ /dev/null @@ -1,41 +0,0 @@ -From f6ba5e17bee38f8ffe118c47fbfef3cf90eb87ff Mon Sep 17 00:00:00 2001 -From: "Mingming.Su" -Date: Wed, 30 Jun 2021 16:59:32 +0800 -Subject: [PATCH] mt7986: trng: add rng support - -1. Add trng compatible name for MT7986 -2. Fix mtk_rng_wait_ready() function - -Signed-off-by: Mingming.Su ---- - drivers/char/hw_random/mtk-rng.c | 5 +++-- - 1 file changed, 3 insertions(+), 2 deletions(-) - ---- a/drivers/char/hw_random/mtk-rng.c -+++ b/drivers/char/hw_random/mtk-rng.c -@@ -22,7 +22,7 @@ - #define RNG_AUTOSUSPEND_TIMEOUT 100 - - #define USEC_POLL 2 --#define TIMEOUT_POLL 20 -+#define TIMEOUT_POLL 60 - - #define RNG_CTRL 0x00 - #define RNG_EN BIT(0) -@@ -77,7 +77,7 @@ static bool mtk_rng_wait_ready(struct hw - readl_poll_timeout_atomic(priv->base + RNG_CTRL, ready, - ready & RNG_READY, USEC_POLL, - TIMEOUT_POLL); -- return !!ready; -+ return !!(ready & RNG_READY); - } - - static int mtk_rng_read(struct hwrng *rng, void *buf, size_t max, bool wait) -@@ -179,6 +179,7 @@ static const struct dev_pm_ops mtk_rng_p - #endif /* CONFIG_PM */ - - static const struct of_device_id mtk_rng_match[] = { -+ { .compatible = "mediatek,mt7986-rng" }, - { .compatible = "mediatek,mt7623-rng" }, - {}, - }; diff --git a/target/linux/mediatek/patches-5.15/410-bt-mtk-serial-fix.patch b/target/linux/mediatek/patches-5.15/410-bt-mtk-serial-fix.patch deleted file mode 100644 index 3f4597c65d..0000000000 --- a/target/linux/mediatek/patches-5.15/410-bt-mtk-serial-fix.patch +++ /dev/null @@ -1,33 +0,0 @@ ---- a/drivers/tty/serial/8250/8250.h -+++ b/drivers/tty/serial/8250/8250.h -@@ -85,6 +85,7 @@ struct serial8250_config { - #define UART_CAP_MINI BIT(17) /* Mini UART on BCM283X family lacks: - * STOP PARITY EPAR SPAR WLEN5 WLEN6 - */ -+#define UART_CAP_NMOD (1 << 18) /* UART doesn't do termios */ - - #define UART_BUG_QUOT BIT(0) /* UART has buggy quot LSB */ - #define UART_BUG_TXEN BIT(1) /* UART has buggy TX IIR status */ ---- a/drivers/tty/serial/8250/8250_port.c -+++ b/drivers/tty/serial/8250/8250_port.c -@@ -289,7 +289,7 @@ static const struct serial8250_config ua - .tx_loadsz = 16, - .fcr = UART_FCR_ENABLE_FIFO | - UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT, -- .flags = UART_CAP_FIFO, -+ .flags = UART_CAP_FIFO | UART_CAP_NMOD, - }, - [PORT_NPCM] = { - .name = "Nuvoton 16550", -@@ -2766,6 +2766,11 @@ serial8250_do_set_termios(struct uart_po - unsigned long flags; - unsigned int baud, quot, frac = 0; - -+ if (up->capabilities & UART_CAP_NMOD) { -+ termios->c_cflag = 0; -+ return; -+ } -+ - if (up->capabilities & UART_CAP_MINI) { - termios->c_cflag &= ~(CSTOPB | PARENB | PARODD | CMSPAR); - if ((termios->c_cflag & CSIZE) == CS5 || diff --git a/target/linux/mediatek/patches-5.15/420-mtd-spi-nor-add-support-for-Winbond-W25Q512JV.patch b/target/linux/mediatek/patches-5.15/420-mtd-spi-nor-add-support-for-Winbond-W25Q512JV.patch deleted file mode 100644 index cc9e9c55e3..0000000000 --- a/target/linux/mediatek/patches-5.15/420-mtd-spi-nor-add-support-for-Winbond-W25Q512JV.patch +++ /dev/null @@ -1,28 +0,0 @@ -From: David Bauer -To: linux-mtd@lists.infradead.org -Subject: [PATCH] mtd: spi-nor: add support for Winbond W25Q512JV -Date: Sat, 13 Feb 2021 16:10:47 +0100 - -The Winbond W25Q512JV is a 512mb SPI-NOR chip. It supports 4K -sectors as well as block protection and Dual-/Quad-read. - -Tested on: Ubiquiti UniFi 6 LR - -Signed-off-by: David Bauer ---- - drivers/mtd/spi-nor/winbond.c | 4 ++++ - 1 file changed, 4 insertions(+) - ---- a/drivers/mtd/spi-nor/winbond.c -+++ b/drivers/mtd/spi-nor/winbond.c -@@ -98,6 +98,10 @@ static const struct flash_info winbond_p - SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, - { "w25q256jw", INFO(0xef6019, 0, 64 * 1024, 512, - SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, -+ { "w25q512jv", INFO(0xef4020, 0, 64 * 1024, 1024, -+ SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_DUAL_READ | -+ SPI_NOR_HAS_TB | SPI_NOR_TB_SR_BIT6 | -+ SPI_NOR_HAS_LOCK | SPI_NOR_4BIT_BP) }, - { "w25m512jv", INFO(0xef7119, 0, 64 * 1024, 1024, - SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_DUAL_READ) }, - { "w25q512jvq", INFO(0xef4020, 0, 64 * 1024, 1024, diff --git a/target/linux/mediatek/patches-5.15/431-drivers-spi-mt65xx-Move-chip_config-to-driver-s-priv.patch b/target/linux/mediatek/patches-5.15/431-drivers-spi-mt65xx-Move-chip_config-to-driver-s-priv.patch deleted file mode 100644 index a57ee25393..0000000000 --- a/target/linux/mediatek/patches-5.15/431-drivers-spi-mt65xx-Move-chip_config-to-driver-s-priv.patch +++ /dev/null @@ -1,130 +0,0 @@ -From bfd3acc428085742d754a6d328d1a93ebf9451df Mon Sep 17 00:00:00 2001 -From: "SkyLake.Huang" -Date: Thu, 23 Jun 2022 18:29:51 +0800 -Subject: [PATCH 1/6] drivers: spi-mt65xx: Move chip_config to driver's private - data - -Signed-off-by: SkyLake.Huang ---- - drivers/spi/spi-mt65xx.c | 29 +++++++++--------------- - include/linux/platform_data/spi-mt65xx.h | 17 -------------- - 2 files changed, 11 insertions(+), 35 deletions(-) - delete mode 100644 include/linux/platform_data/spi-mt65xx.h - ---- a/drivers/spi/spi-mt65xx.c -+++ b/drivers/spi/spi-mt65xx.c -@@ -14,7 +14,6 @@ - #include - #include - #include --#include - #include - #include - #include -@@ -142,6 +141,8 @@ struct mtk_spi { - struct device *dev; - dma_addr_t tx_dma; - dma_addr_t rx_dma; -+ u32 sample_sel; -+ u32 get_tick_dly; - }; - - static const struct mtk_spi_compatible mtk_common_compat; -@@ -187,15 +188,6 @@ static const struct mtk_spi_compatible m - .no_need_unprepare = true, - }; - --/* -- * A piece of default chip info unless the platform -- * supplies it. -- */ --static const struct mtk_chip_config mtk_default_chip_info = { -- .sample_sel = 0, -- .tick_delay = 0, --}; -- - static const struct of_device_id mtk_spi_of_match[] = { - { .compatible = "mediatek,spi-ipm", - .data = (void *)&mtk_ipm_compat, -@@ -323,7 +315,6 @@ static int mtk_spi_hw_init(struct spi_ma - { - u16 cpha, cpol; - u32 reg_val; -- struct mtk_chip_config *chip_config = spi->controller_data; - struct mtk_spi *mdata = spi_master_get_devdata(master); - - cpha = spi->mode & SPI_CPHA ? 1 : 0; -@@ -373,7 +364,7 @@ static int mtk_spi_hw_init(struct spi_ma - else - reg_val &= ~SPI_CMD_CS_POL; - -- if (chip_config->sample_sel) -+ if (mdata->sample_sel) - reg_val |= SPI_CMD_SAMPLE_SEL; - else - reg_val &= ~SPI_CMD_SAMPLE_SEL; -@@ -400,20 +391,20 @@ static int mtk_spi_hw_init(struct spi_ma - if (mdata->dev_comp->ipm_design) { - reg_val = readl(mdata->base + SPI_CMD_REG); - reg_val &= ~SPI_CMD_IPM_GET_TICKDLY_MASK; -- reg_val |= ((chip_config->tick_delay & 0x7) -+ reg_val |= ((mdata->get_tick_dly & 0x7) - << SPI_CMD_IPM_GET_TICKDLY_OFFSET); - writel(reg_val, mdata->base + SPI_CMD_REG); - } else { - reg_val = readl(mdata->base + SPI_CFG1_REG); - reg_val &= ~SPI_CFG1_GET_TICK_DLY_MASK; -- reg_val |= ((chip_config->tick_delay & 0x7) -+ reg_val |= ((mdata->get_tick_dly & 0x7) - << SPI_CFG1_GET_TICK_DLY_OFFSET); - writel(reg_val, mdata->base + SPI_CFG1_REG); - } - } else { - reg_val = readl(mdata->base + SPI_CFG1_REG); - reg_val &= ~SPI_CFG1_GET_TICK_DLY_MASK_V1; -- reg_val |= ((chip_config->tick_delay & 0x3) -+ reg_val |= ((mdata->get_tick_dly & 0x3) - << SPI_CFG1_GET_TICK_DLY_OFFSET_V1); - writel(reg_val, mdata->base + SPI_CFG1_REG); - } -@@ -700,9 +691,6 @@ static int mtk_spi_setup(struct spi_devi - { - struct mtk_spi *mdata = spi_master_get_devdata(spi->master); - -- if (!spi->controller_data) -- spi->controller_data = (void *)&mtk_default_chip_info; -- - if (mdata->dev_comp->need_pad_sel && spi->cs_gpiod) - /* CS de-asserted, gpiolib will handle inversion */ - gpiod_direction_output(spi->cs_gpiod, 0); -@@ -1115,6 +1103,10 @@ static int mtk_spi_probe(struct platform - mdata = spi_master_get_devdata(master); - mdata->dev_comp = of_id->data; - -+ /* Set device configs to default first. Calibrate it later. */ -+ mdata->sample_sel = 0; -+ mdata->get_tick_dly = 2; -+ - if (mdata->dev_comp->enhance_timing) - master->mode_bits |= SPI_CS_HIGH; - ---- a/include/linux/platform_data/spi-mt65xx.h -+++ /dev/null -@@ -1,17 +0,0 @@ --/* SPDX-License-Identifier: GPL-2.0-only */ --/* -- * MTK SPI bus driver definitions -- * -- * Copyright (c) 2015 MediaTek Inc. -- * Author: Leilk Liu -- */ -- --#ifndef ____LINUX_PLATFORM_DATA_SPI_MTK_H --#define ____LINUX_PLATFORM_DATA_SPI_MTK_H -- --/* Board specific platform_data */ --struct mtk_chip_config { -- u32 sample_sel; -- u32 tick_delay; --}; --#endif diff --git a/target/linux/mediatek/patches-5.15/432-drivers-spi-Add-support-for-dynamic-calibration.patch b/target/linux/mediatek/patches-5.15/432-drivers-spi-Add-support-for-dynamic-calibration.patch deleted file mode 100644 index e795eda3b2..0000000000 --- a/target/linux/mediatek/patches-5.15/432-drivers-spi-Add-support-for-dynamic-calibration.patch +++ /dev/null @@ -1,236 +0,0 @@ -From 2ade0172154e50c8a2bfd8634c6eff943cffea29 Mon Sep 17 00:00:00 2001 -From: "SkyLake.Huang" -Date: Thu, 23 Jun 2022 18:35:52 +0800 -Subject: [PATCH 2/6] drivers: spi: Add support for dynamic calibration - -Signed-off-by: SkyLake.Huang ---- - drivers/spi/spi.c | 137 ++++++++++++++++++++++++++++++++++++++++ - include/linux/spi/spi.h | 42 ++++++++++++ - 2 files changed, 179 insertions(+) - ---- a/drivers/spi/spi.c -+++ b/drivers/spi/spi.c -@@ -1246,6 +1246,70 @@ static int spi_transfer_wait(struct spi_ - return 0; - } - -+int spi_do_calibration(struct spi_controller *ctlr, struct spi_device *spi, -+ int (*cal_read)(void *priv, u32 *addr, int addrlen, u8 *buf, int readlen), void *drv_priv) -+{ -+ int datalen = ctlr->cal_rule->datalen; -+ int addrlen = ctlr->cal_rule->addrlen; -+ u8 *buf; -+ int ret; -+ int i; -+ struct list_head *cal_head, *listptr; -+ struct spi_cal_target *target; -+ -+ /* Calculate calibration result */ -+ int hit_val, total_hit, origin; -+ bool hit; -+ -+ /* Make sure we can start calibration */ -+ if(!ctlr->cal_target || !ctlr->cal_rule || !ctlr->append_caldata) -+ return 0; -+ -+ buf = kzalloc(datalen * sizeof(u8), GFP_KERNEL); -+ if(!buf) -+ return -ENOMEM; -+ -+ ret = ctlr->append_caldata(ctlr); -+ if (ret) -+ goto cal_end; -+ -+ cal_head = ctlr->cal_target; -+ list_for_each(listptr, cal_head) { -+ target = list_entry(listptr, struct spi_cal_target, list); -+ -+ hit = false; -+ hit_val = 0; -+ total_hit = 0; -+ origin = *target->cal_item; -+ -+ for(i=target->cal_min; i<=target->cal_max; i+=target->step) { -+ *target->cal_item = i; -+ ret = (*cal_read)(drv_priv, ctlr->cal_rule->addr, addrlen, buf, datalen); -+ if(ret) -+ break; -+ dev_dbg(&spi->dev, "controller cal item value: 0x%x\n", i); -+ if(memcmp(ctlr->cal_rule->match_data, buf, datalen * sizeof(u8)) == 0) { -+ hit = true; -+ hit_val += i; -+ total_hit++; -+ dev_dbg(&spi->dev, "golden data matches data read!\n"); -+ } -+ } -+ if(hit) { -+ *target->cal_item = DIV_ROUND_CLOSEST(hit_val, total_hit); -+ dev_info(&spi->dev, "calibration result: 0x%x", *target->cal_item); -+ } else { -+ *target->cal_item = origin; -+ dev_warn(&spi->dev, "calibration failed, fallback to default: 0x%x", origin); -+ } -+ } -+ -+cal_end: -+ kfree(buf); -+ return ret? ret: 0; -+} -+EXPORT_SYMBOL_GPL(spi_do_calibration); -+ - static void _spi_transfer_delay_ns(u32 ns) - { - if (!ns) -@@ -2033,6 +2097,75 @@ void spi_flush_queue(struct spi_controll - /*-------------------------------------------------------------------------*/ - - #if defined(CONFIG_OF) -+static inline void alloc_cal_data(struct list_head **cal_target, -+ struct spi_cal_rule **cal_rule, bool enable) -+{ -+ if(enable) { -+ *cal_target = kmalloc(sizeof(struct list_head), GFP_KERNEL); -+ INIT_LIST_HEAD(*cal_target); -+ *cal_rule = kmalloc(sizeof(struct spi_cal_rule), GFP_KERNEL); -+ } else { -+ kfree(*cal_target); -+ kfree(*cal_rule); -+ } -+} -+ -+static int of_spi_parse_cal_dt(struct spi_controller *ctlr, struct spi_device *spi, -+ struct device_node *nc) -+{ -+ u32 value; -+ int rc; -+ const char *cal_mode; -+ -+ rc = of_property_read_bool(nc, "spi-cal-enable"); -+ if (rc) -+ alloc_cal_data(&ctlr->cal_target, &ctlr->cal_rule, true); -+ else -+ return 0; -+ -+ rc = of_property_read_string(nc, "spi-cal-mode", &cal_mode); -+ if(!rc) { -+ if(strcmp("read-data", cal_mode) == 0){ -+ ctlr->cal_rule->mode = SPI_CAL_READ_DATA; -+ } else if(strcmp("read-pp", cal_mode) == 0) { -+ ctlr->cal_rule->mode = SPI_CAL_READ_PP; -+ return 0; -+ } else if(strcmp("read-sfdp", cal_mode) == 0){ -+ ctlr->cal_rule->mode = SPI_CAL_READ_SFDP; -+ return 0; -+ } -+ } else -+ goto err; -+ -+ ctlr->cal_rule->datalen = 0; -+ rc = of_property_read_u32(nc, "spi-cal-datalen", &value); -+ if(!rc && value > 0) { -+ ctlr->cal_rule->datalen = value; -+ -+ ctlr->cal_rule->match_data = kzalloc(value * sizeof(u8), GFP_KERNEL); -+ rc = of_property_read_u8_array(nc, "spi-cal-data", -+ ctlr->cal_rule->match_data, value); -+ if(rc) -+ kfree(ctlr->cal_rule->match_data); -+ } -+ -+ rc = of_property_read_u32(nc, "spi-cal-addrlen", &value); -+ if(!rc && value > 0) { -+ ctlr->cal_rule->addrlen = value; -+ -+ ctlr->cal_rule->addr = kzalloc(value * sizeof(u32), GFP_KERNEL); -+ rc = of_property_read_u32_array(nc, "spi-cal-addr", -+ ctlr->cal_rule->addr, value); -+ if(rc) -+ kfree(ctlr->cal_rule->addr); -+ } -+ return 0; -+ -+err: -+ alloc_cal_data(&ctlr->cal_target, &ctlr->cal_rule, false); -+ return 0; -+} -+ - static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi, - struct device_node *nc) - { -@@ -2151,6 +2284,10 @@ of_register_spi_device(struct spi_contro - if (rc) - goto err_out; - -+ rc = of_spi_parse_cal_dt(ctlr, spi, nc); -+ if (rc) -+ goto err_out; -+ - /* Store a pointer to the node in the device structure */ - of_node_get(nc); - spi->dev.of_node = nc; ---- a/include/linux/spi/spi.h -+++ b/include/linux/spi/spi.h -@@ -290,6 +290,40 @@ struct spi_driver { - struct device_driver driver; - }; - -+enum { -+ SPI_CAL_READ_DATA = 0, -+ SPI_CAL_READ_PP = 1, /* only for SPI-NAND */ -+ SPI_CAL_READ_SFDP = 2, /* only for SPI-NOR */ -+}; -+ -+struct nand_addr { -+ unsigned int lun; -+ unsigned int plane; -+ unsigned int eraseblock; -+ unsigned int page; -+ unsigned int dataoffs; -+}; -+ -+/** -+ * Read calibration rule from device dts node. -+ * Once calibration result matches the rule, we regard is as success. -+ */ -+struct spi_cal_rule { -+ int datalen; -+ u8 *match_data; -+ int addrlen; -+ u32 *addr; -+ int mode; -+}; -+ -+struct spi_cal_target { -+ u32 *cal_item; -+ int cal_min; /* min of cal_item */ -+ int cal_max; /* max of cal_item */ -+ int step; /* Increase/decrease cal_item */ -+ struct list_head list; -+}; -+ - static inline struct spi_driver *to_spi_driver(struct device_driver *drv) - { - return drv ? container_of(drv, struct spi_driver, driver) : NULL; -@@ -665,6 +699,11 @@ struct spi_controller { - void *dummy_rx; - void *dummy_tx; - -+ /* For calibration */ -+ int (*append_caldata)(struct spi_controller *ctlr); -+ struct list_head *cal_target; -+ struct spi_cal_rule *cal_rule; -+ - int (*fw_translate_cs)(struct spi_controller *ctlr, unsigned cs); - - /* -@@ -1477,6 +1516,9 @@ spi_register_board_info(struct spi_board - { return 0; } - #endif - -+extern int spi_do_calibration(struct spi_controller *ctlr, -+ struct spi_device *spi, int (*cal_read)(void *, u32 *, int, u8 *, int), void *drv_priv); -+ - /* If you're hotplugging an adapter with devices (parport, usb, etc) - * use spi_new_device() to describe each device. You can also call - * spi_unregister_device() to start making that device vanish, but diff --git a/target/linux/mediatek/patches-5.15/433-drivers-spi-mem-Add-spi-calibration-hook.patch b/target/linux/mediatek/patches-5.15/433-drivers-spi-mem-Add-spi-calibration-hook.patch deleted file mode 100644 index aaacab0131..0000000000 --- a/target/linux/mediatek/patches-5.15/433-drivers-spi-mem-Add-spi-calibration-hook.patch +++ /dev/null @@ -1,41 +0,0 @@ -From 06640a5da2973318c06e516da16a5b579622e7c5 Mon Sep 17 00:00:00 2001 -From: "SkyLake.Huang" -Date: Thu, 23 Jun 2022 18:37:55 +0800 -Subject: [PATCH 3/6] drivers: spi-mem: Add spi calibration hook - -Signed-off-by: SkyLake.Huang ---- - drivers/spi/spi-mem.c | 8 ++++++++ - include/linux/spi/spi-mem.h | 4 ++++ - 2 files changed, 12 insertions(+) - ---- a/drivers/spi/spi-mem.c -+++ b/drivers/spi/spi-mem.c -@@ -410,6 +410,14 @@ int spi_mem_exec_op(struct spi_mem *mem, - } - EXPORT_SYMBOL_GPL(spi_mem_exec_op); - -+int spi_mem_do_calibration(struct spi_mem *mem, -+ int (*cal_read)(void *priv, u32 *addr, int addrlen, u8 *buf, int readlen), -+ void *priv) -+{ -+ return spi_do_calibration(mem->spi->controller, mem->spi, cal_read, priv); -+} -+EXPORT_SYMBOL_GPL(spi_mem_do_calibration); -+ - /** - * spi_mem_get_name() - Return the SPI mem device name to be used by the - * upper layer if necessary ---- a/include/linux/spi/spi-mem.h -+++ b/include/linux/spi/spi-mem.h -@@ -366,6 +366,10 @@ bool spi_mem_supports_op(struct spi_mem - int spi_mem_exec_op(struct spi_mem *mem, - const struct spi_mem_op *op); - -+int spi_mem_do_calibration(struct spi_mem *mem, -+ int (*cal_read)(void *, u32 *, int, u8 *, int), -+ void *priv); -+ - const char *spi_mem_get_name(struct spi_mem *mem); - - struct spi_mem_dirmap_desc * diff --git a/target/linux/mediatek/patches-5.15/434-drivers-spi-mt65xx-Add-controller-s-calibration-para.patch b/target/linux/mediatek/patches-5.15/434-drivers-spi-mt65xx-Add-controller-s-calibration-para.patch deleted file mode 100644 index a64d622981..0000000000 --- a/target/linux/mediatek/patches-5.15/434-drivers-spi-mt65xx-Add-controller-s-calibration-para.patch +++ /dev/null @@ -1,43 +0,0 @@ -From d278c7a0bf730318a7ccf8d0a8b434c813e23fd0 Mon Sep 17 00:00:00 2001 -From: "SkyLake.Huang" -Date: Thu, 23 Jun 2022 18:39:03 +0800 -Subject: [PATCH 4/6] drivers: spi-mt65xx: Add controller's calibration - paramter - -Signed-off-by: SkyLake.Huang ---- - drivers/spi/spi-mt65xx.c | 16 ++++++++++++++++ - 1 file changed, 16 insertions(+) - ---- a/drivers/spi/spi-mt65xx.c -+++ b/drivers/spi/spi-mt65xx.c -@@ -800,6 +800,21 @@ static irqreturn_t mtk_spi_interrupt(int - return IRQ_HANDLED; - } - -+static int mtk_spi_append_caldata(struct spi_controller *ctlr) -+{ -+ struct spi_cal_target *cal_target = kmalloc(sizeof(*cal_target), GFP_KERNEL); -+ struct mtk_spi *mdata = spi_master_get_devdata(ctlr); -+ -+ cal_target->cal_item = &mdata->get_tick_dly; -+ cal_target->cal_min = 0; -+ cal_target->cal_max = 7; -+ cal_target->step = 1; -+ -+ list_add(&cal_target->list, ctlr->cal_target); -+ -+ return 0; -+} -+ - static int mtk_spi_mem_adjust_op_size(struct spi_mem *mem, - struct spi_mem_op *op) - { -@@ -1092,6 +1107,7 @@ static int mtk_spi_probe(struct platform - master->setup = mtk_spi_setup; - master->set_cs_timing = mtk_spi_set_hw_cs_timing; - master->use_gpio_descriptors = true; -+ master->append_caldata = mtk_spi_append_caldata; - - of_id = of_match_node(mtk_spi_of_match, pdev->dev.of_node); - if (!of_id) { diff --git a/target/linux/mediatek/patches-5.15/435-drivers-mtd-spinand-Add-calibration-support-for-spin.patch b/target/linux/mediatek/patches-5.15/435-drivers-mtd-spinand-Add-calibration-support-for-spin.patch deleted file mode 100644 index e2684eebb7..0000000000 --- a/target/linux/mediatek/patches-5.15/435-drivers-mtd-spinand-Add-calibration-support-for-spin.patch +++ /dev/null @@ -1,81 +0,0 @@ -From 7670ec4a14891a1a182b98a9c403ffbf6b49e4b1 Mon Sep 17 00:00:00 2001 -From: "SkyLake.Huang" -Date: Thu, 23 Jun 2022 18:39:56 +0800 -Subject: [PATCH 5/6] drivers: mtd: spinand: Add calibration support for - spinand - -Signed-off-by: SkyLake.Huang ---- - drivers/mtd/nand/spi/core.c | 54 +++++++++++++++++++++++++++++++++++++ - 1 file changed, 54 insertions(+) - ---- a/drivers/mtd/nand/spi/core.c -+++ b/drivers/mtd/nand/spi/core.c -@@ -977,6 +977,56 @@ static int spinand_manufacturer_match(st - return -ENOTSUPP; - } - -+int spinand_cal_read(void *priv, u32 *addr, int addrlen, u8 *buf, int readlen) { -+ struct spinand_device *spinand = (struct spinand_device *)priv; -+ struct device *dev = &spinand->spimem->spi->dev; -+ struct spi_mem_op op = SPINAND_PAGE_READ_FROM_CACHE_OP(false, 0, 1, buf, readlen); -+ struct nand_pos pos; -+ struct nand_page_io_req req; -+ u8 status; -+ int ret; -+ -+ if(addrlen != sizeof(struct nand_addr)/sizeof(unsigned int)) { -+ dev_err(dev, "Must provide correct addr(length) for spinand calibration\n"); -+ return -EINVAL; -+ } -+ -+ ret = spinand_reset_op(spinand); -+ if (ret) -+ return ret; -+ -+ /* We should store our golden data in first target because -+ * we can't switch target at this moment. -+ */ -+ pos = (struct nand_pos){ -+ .target = 0, -+ .lun = *addr, -+ .plane = *(addr+1), -+ .eraseblock = *(addr+2), -+ .page = *(addr+3), -+ }; -+ -+ req = (struct nand_page_io_req){ -+ .pos = pos, -+ .dataoffs = *(addr+4), -+ .datalen = readlen, -+ .databuf.in = buf, -+ .mode = MTD_OPS_AUTO_OOB, -+ }; -+ -+ ret = spinand_load_page_op(spinand, &req); -+ if (ret) -+ return ret; -+ -+ ret = spinand_wait(spinand, &status); -+ if (ret < 0) -+ return ret; -+ -+ ret = spi_mem_exec_op(spinand->spimem, &op); -+ -+ return 0; -+} -+ - static int spinand_id_detect(struct spinand_device *spinand) - { - u8 *id = spinand->id.data; -@@ -1227,6 +1277,10 @@ static int spinand_init(struct spinand_d - if (!spinand->scratchbuf) - return -ENOMEM; - -+ ret = spi_mem_do_calibration(spinand->spimem, spinand_cal_read, spinand); -+ if (ret) -+ dev_err(dev, "Failed to calibrate SPI-NAND (err = %d)\n", ret); -+ - ret = spinand_detect(spinand); - if (ret) - goto err_free_bufs; diff --git a/target/linux/mediatek/patches-5.15/436-drivers-mtd-spi-nor-Add-calibration-support-for-spi-.patch b/target/linux/mediatek/patches-5.15/436-drivers-mtd-spi-nor-Add-calibration-support-for-spi-.patch deleted file mode 100644 index 61712982fb..0000000000 --- a/target/linux/mediatek/patches-5.15/436-drivers-mtd-spi-nor-Add-calibration-support-for-spi-.patch +++ /dev/null @@ -1,57 +0,0 @@ -From f3fe3b15eca7908eaac57f9b8387a5dbc45ec5b2 Mon Sep 17 00:00:00 2001 -From: "SkyLake.Huang" -Date: Thu, 23 Jun 2022 18:40:59 +0800 -Subject: [PATCH 6/6] drivers: mtd: spi-nor: Add calibration support for - spi-nor - -Signed-off-by: SkyLake.Huang ---- - drivers/mtd/nand/spi/core.c | 5 ++++- - drivers/mtd/spi-nor/core.c | 15 +++++++++++++++ - 2 files changed, 19 insertions(+), 1 deletion(-) - ---- a/drivers/mtd/nand/spi/core.c -+++ b/drivers/mtd/nand/spi/core.c -@@ -1018,7 +1018,10 @@ int spinand_cal_read(void *priv, u32 *ad - if (ret) - return ret; - -- ret = spinand_wait(spinand, &status); -+ ret = spinand_wait(spinand, -+ SPINAND_READ_INITIAL_DELAY_US, -+ SPINAND_READ_POLL_DELAY_US, -+ &status); - if (ret < 0) - return ret; - ---- a/drivers/mtd/spi-nor/core.c -+++ b/drivers/mtd/spi-nor/core.c -@@ -3061,6 +3061,18 @@ static void spi_nor_debugfs_init(struct - info->id_len, info->id); - } - -+static int spi_nor_cal_read(void *priv, u32 *addr, int addrlen, u8 *buf, int readlen) -+{ -+ struct spi_nor *nor = (struct spi_nor *)priv; -+ -+ nor->reg_proto = SNOR_PROTO_1_1_1; -+ nor->read_proto = SNOR_PROTO_1_1_1; -+ nor->read_opcode = SPINOR_OP_READ; -+ nor->read_dummy = 0; -+ -+ return nor->controller_ops->read(nor, *addr, readlen, buf); -+} -+ - static const struct flash_info *spi_nor_get_flash_info(struct spi_nor *nor, - const char *name) - { -@@ -3134,6 +3146,9 @@ int spi_nor_scan(struct spi_nor *nor, co - if (!nor->bouncebuf) - return -ENOMEM; - -+ if(nor->spimem) -+ spi_mem_do_calibration(nor->spimem, spi_nor_cal_read, nor); -+ - info = spi_nor_get_flash_info(nor, name); - if (IS_ERR(info)) - return PTR_ERR(info); diff --git a/target/linux/mediatek/patches-5.15/500-gsw-rtl8367s-mt7622-support.patch b/target/linux/mediatek/patches-5.15/500-gsw-rtl8367s-mt7622-support.patch deleted file mode 100644 index 977bdeb5b1..0000000000 --- a/target/linux/mediatek/patches-5.15/500-gsw-rtl8367s-mt7622-support.patch +++ /dev/null @@ -1,25 +0,0 @@ ---- a/drivers/net/phy/Kconfig -+++ b/drivers/net/phy/Kconfig -@@ -364,6 +364,12 @@ config ROCKCHIP_PHY - help - Currently supports the integrated Ethernet PHY. - -+config RTL8367S_GSW -+ tristate "rtl8367 Gigabit Switch support for mt7622" -+ depends on NET_VENDOR_MEDIATEK -+ help -+ This driver supports rtl8367s in mt7622 -+ - config SMSC_PHY - tristate "SMSC PHYs" - help ---- a/drivers/net/phy/Makefile -+++ b/drivers/net/phy/Makefile -@@ -91,6 +91,7 @@ obj-$(CONFIG_QSEMI_PHY) += qsemi.o - obj-$(CONFIG_REALTEK_PHY) += realtek.o - obj-$(CONFIG_RENESAS_PHY) += uPD60620.o - obj-$(CONFIG_ROCKCHIP_PHY) += rockchip.o -+obj-$(CONFIG_RTL8367S_GSW) += rtk/ - obj-$(CONFIG_SMSC_PHY) += smsc.o - obj-$(CONFIG_STE10XP) += ste10Xp.o - obj-$(CONFIG_TERANETICS_PHY) += teranetics.o diff --git a/target/linux/mediatek/patches-5.15/600-v5.16-arm64-dts-mediatek-Split-PCIe-node-for-MT2712-and-MT.patch b/target/linux/mediatek/patches-5.15/600-v5.16-arm64-dts-mediatek-Split-PCIe-node-for-MT2712-and-MT.patch deleted file mode 100644 index 6a84ff47db..0000000000 --- a/target/linux/mediatek/patches-5.15/600-v5.16-arm64-dts-mediatek-Split-PCIe-node-for-MT2712-and-MT.patch +++ /dev/null @@ -1,332 +0,0 @@ -From: Chuanjia Liu -Date: Mon, 23 Aug 2021 11:27:59 +0800 -Subject: [PATCH] arm64: dts: mediatek: Split PCIe node for MT2712 and MT7622 - -There are two independent PCIe controllers in MT2712 and MT7622 -platform. Each of them should contain an independent MSI domain. - -In old dts architecture, MSI domain will be inherited from the root -bridge, and all of the devices will share the same MSI domain. -Hence that, the PCIe devices will not work properly if the irq number -which required is more than 32. - -Split the PCIe node for MT2712 and MT7622 platform to comply with -the hardware design and fix MSI issue. - -Signed-off-by: Chuanjia Liu -Acked-by: Ryder Lee -Link: https://lore.kernel.org/r/20210823032800.1660-6-chuanjia.liu@mediatek.com -Signed-off-by: Matthias Brugger ---- - ---- a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi -@@ -915,64 +915,67 @@ - }; - }; - -- pcie: pcie@11700000 { -+ pcie1: pcie@112ff000 { - compatible = "mediatek,mt2712-pcie"; - device_type = "pci"; -- reg = <0 0x11700000 0 0x1000>, -- <0 0x112ff000 0 0x1000>; -- reg-names = "port0", "port1"; -+ reg = <0 0x112ff000 0 0x1000>; -+ reg-names = "port1"; -+ linux,pci-domain = <1>; - #address-cells = <3>; - #size-cells = <2>; -- interrupts = , -- ; -- clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>, -- <&topckgen CLK_TOP_PE2_MAC_P1_SEL>, -- <&pericfg CLK_PERI_PCIE0>, -+ interrupts = ; -+ interrupt-names = "pcie_irq"; -+ clocks = <&topckgen CLK_TOP_PE2_MAC_P1_SEL>, - <&pericfg CLK_PERI_PCIE1>; -- clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1"; -- phys = <&u3port0 PHY_TYPE_PCIE>, <&u3port1 PHY_TYPE_PCIE>; -- phy-names = "pcie-phy0", "pcie-phy1"; -+ clock-names = "sys_ck1", "ahb_ck1"; -+ phys = <&u3port1 PHY_TYPE_PCIE>; -+ phy-names = "pcie-phy1"; - bus-range = <0x00 0xff>; -- ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; -+ ranges = <0x82000000 0 0x11400000 0x0 0x11400000 0 0x300000>; -+ status = "disabled"; - -- pcie0: pcie@0,0 { -- device_type = "pci"; -- status = "disabled"; -- reg = <0x0000 0 0 0 0>; -- #address-cells = <3>; -- #size-cells = <2>; -+ #interrupt-cells = <1>; -+ interrupt-map-mask = <0 0 0 7>; -+ interrupt-map = <0 0 0 1 &pcie_intc1 0>, -+ <0 0 0 2 &pcie_intc1 1>, -+ <0 0 0 3 &pcie_intc1 2>, -+ <0 0 0 4 &pcie_intc1 3>; -+ pcie_intc1: interrupt-controller { -+ interrupt-controller; -+ #address-cells = <0>; - #interrupt-cells = <1>; -- ranges; -- interrupt-map-mask = <0 0 0 7>; -- interrupt-map = <0 0 0 1 &pcie_intc0 0>, -- <0 0 0 2 &pcie_intc0 1>, -- <0 0 0 3 &pcie_intc0 2>, -- <0 0 0 4 &pcie_intc0 3>; -- pcie_intc0: interrupt-controller { -- interrupt-controller; -- #address-cells = <0>; -- #interrupt-cells = <1>; -- }; - }; -+ }; -+ -+ pcie0: pcie@11700000 { -+ compatible = "mediatek,mt2712-pcie"; -+ device_type = "pci"; -+ reg = <0 0x11700000 0 0x1000>; -+ reg-names = "port0"; -+ linux,pci-domain = <0>; -+ #address-cells = <3>; -+ #size-cells = <2>; -+ interrupts = ; -+ interrupt-names = "pcie_irq"; -+ clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>, -+ <&pericfg CLK_PERI_PCIE0>; -+ clock-names = "sys_ck0", "ahb_ck0"; -+ phys = <&u3port0 PHY_TYPE_PCIE>; -+ phy-names = "pcie-phy0"; -+ bus-range = <0x00 0xff>; -+ ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; -+ status = "disabled"; - -- pcie1: pcie@1,0 { -- device_type = "pci"; -- status = "disabled"; -- reg = <0x0800 0 0 0 0>; -- #address-cells = <3>; -- #size-cells = <2>; -+ #interrupt-cells = <1>; -+ interrupt-map-mask = <0 0 0 7>; -+ interrupt-map = <0 0 0 1 &pcie_intc0 0>, -+ <0 0 0 2 &pcie_intc0 1>, -+ <0 0 0 3 &pcie_intc0 2>, -+ <0 0 0 4 &pcie_intc0 3>; -+ pcie_intc0: interrupt-controller { -+ interrupt-controller; -+ #address-cells = <0>; - #interrupt-cells = <1>; -- ranges; -- interrupt-map-mask = <0 0 0 7>; -- interrupt-map = <0 0 0 1 &pcie_intc1 0>, -- <0 0 0 2 &pcie_intc1 1>, -- <0 0 0 3 &pcie_intc1 2>, -- <0 0 0 4 &pcie_intc1 3>; -- pcie_intc1: interrupt-controller { -- interrupt-controller; -- #address-cells = <0>; -- #interrupt-cells = <1>; -- }; - }; - }; - ---- a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -@@ -302,18 +302,16 @@ - }; - }; - --&pcie { -+&pcie0 { - pinctrl-names = "default"; -- pinctrl-0 = <&pcie0_pins>, <&pcie1_pins>; -+ pinctrl-0 = <&pcie0_pins>; - status = "okay"; -+}; - -- pcie@0,0 { -- status = "okay"; -- }; -- -- pcie@1,0 { -- status = "okay"; -- }; -+&pcie1 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&pcie1_pins>; -+ status = "okay"; - }; - - &pio { ---- a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts -+++ b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts -@@ -232,18 +232,16 @@ - }; - }; - --&pcie { -+&pcie0 { - pinctrl-names = "default"; -- pinctrl-0 = <&pcie0_pins>, <&pcie1_pins>; -+ pinctrl-0 = <&pcie0_pins>; - status = "okay"; -+}; - -- pcie@0,0 { -- status = "okay"; -- }; -- -- pcie@1,0 { -- status = "okay"; -- }; -+&pcie1 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&pcie1_pins>; -+ status = "okay"; - }; - - &pio { ---- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi -@@ -809,75 +809,83 @@ - #reset-cells = <1>; - }; - -- pcie: pcie@1a140000 { -+ pciecfg: pciecfg@1a140000 { -+ compatible = "mediatek,generic-pciecfg", "syscon"; -+ reg = <0 0x1a140000 0 0x1000>; -+ }; -+ -+ pcie0: pcie@1a143000 { - compatible = "mediatek,mt7622-pcie"; - device_type = "pci"; -- reg = <0 0x1a140000 0 0x1000>, -- <0 0x1a143000 0 0x1000>, -- <0 0x1a145000 0 0x1000>; -- reg-names = "subsys", "port0", "port1"; -+ reg = <0 0x1a143000 0 0x1000>; -+ reg-names = "port0"; -+ linux,pci-domain = <0>; - #address-cells = <3>; - #size-cells = <2>; -- interrupts = , -- ; -+ interrupts = ; -+ interrupt-names = "pcie_irq"; - clocks = <&pciesys CLK_PCIE_P0_MAC_EN>, -- <&pciesys CLK_PCIE_P1_MAC_EN>, -- <&pciesys CLK_PCIE_P0_AHB_EN>, - <&pciesys CLK_PCIE_P0_AHB_EN>, - <&pciesys CLK_PCIE_P0_AUX_EN>, -- <&pciesys CLK_PCIE_P1_AUX_EN>, - <&pciesys CLK_PCIE_P0_AXI_EN>, -- <&pciesys CLK_PCIE_P1_AXI_EN>, - <&pciesys CLK_PCIE_P0_OBFF_EN>, -- <&pciesys CLK_PCIE_P1_OBFF_EN>, -- <&pciesys CLK_PCIE_P0_PIPE_EN>, -- <&pciesys CLK_PCIE_P1_PIPE_EN>; -- clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1", -- "aux_ck0", "aux_ck1", "axi_ck0", "axi_ck1", -- "obff_ck0", "obff_ck1", "pipe_ck0", "pipe_ck1"; -+ <&pciesys CLK_PCIE_P0_PIPE_EN>; -+ clock-names = "sys_ck0", "ahb_ck0", "aux_ck0", -+ "axi_ck0", "obff_ck0", "pipe_ck0"; -+ - power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>; - bus-range = <0x00 0xff>; -- ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; -+ ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x8000000>; - status = "disabled"; - -- pcie0: pcie@0,0 { -- reg = <0x0000 0 0 0 0>; -- #address-cells = <3>; -- #size-cells = <2>; -+ #interrupt-cells = <1>; -+ interrupt-map-mask = <0 0 0 7>; -+ interrupt-map = <0 0 0 1 &pcie_intc0 0>, -+ <0 0 0 2 &pcie_intc0 1>, -+ <0 0 0 3 &pcie_intc0 2>, -+ <0 0 0 4 &pcie_intc0 3>; -+ pcie_intc0: interrupt-controller { -+ interrupt-controller; -+ #address-cells = <0>; - #interrupt-cells = <1>; -- ranges; -- status = "disabled"; -- -- interrupt-map-mask = <0 0 0 7>; -- interrupt-map = <0 0 0 1 &pcie_intc0 0>, -- <0 0 0 2 &pcie_intc0 1>, -- <0 0 0 3 &pcie_intc0 2>, -- <0 0 0 4 &pcie_intc0 3>; -- pcie_intc0: interrupt-controller { -- interrupt-controller; -- #address-cells = <0>; -- #interrupt-cells = <1>; -- }; - }; -+ }; - -- pcie1: pcie@1,0 { -- reg = <0x0800 0 0 0 0>; -- #address-cells = <3>; -- #size-cells = <2>; -- #interrupt-cells = <1>; -- ranges; -- status = "disabled"; -+ pcie1: pcie@1a145000 { -+ compatible = "mediatek,mt7622-pcie"; -+ device_type = "pci"; -+ reg = <0 0x1a145000 0 0x1000>; -+ reg-names = "port1"; -+ linux,pci-domain = <1>; -+ #address-cells = <3>; -+ #size-cells = <2>; -+ interrupts = ; -+ interrupt-names = "pcie_irq"; -+ clocks = <&pciesys CLK_PCIE_P1_MAC_EN>, -+ /* designer has connect RC1 with p0_ahb clock */ -+ <&pciesys CLK_PCIE_P0_AHB_EN>, -+ <&pciesys CLK_PCIE_P1_AUX_EN>, -+ <&pciesys CLK_PCIE_P1_AXI_EN>, -+ <&pciesys CLK_PCIE_P1_OBFF_EN>, -+ <&pciesys CLK_PCIE_P1_PIPE_EN>; -+ clock-names = "sys_ck1", "ahb_ck1", "aux_ck1", -+ "axi_ck1", "obff_ck1", "pipe_ck1"; -+ -+ power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>; -+ bus-range = <0x00 0xff>; -+ ranges = <0x82000000 0 0x28000000 0x0 0x28000000 0 0x8000000>; -+ status = "disabled"; - -- interrupt-map-mask = <0 0 0 7>; -- interrupt-map = <0 0 0 1 &pcie_intc1 0>, -- <0 0 0 2 &pcie_intc1 1>, -- <0 0 0 3 &pcie_intc1 2>, -- <0 0 0 4 &pcie_intc1 3>; -- pcie_intc1: interrupt-controller { -- interrupt-controller; -- #address-cells = <0>; -- #interrupt-cells = <1>; -- }; -+ #interrupt-cells = <1>; -+ interrupt-map-mask = <0 0 0 7>; -+ interrupt-map = <0 0 0 1 &pcie_intc1 0>, -+ <0 0 0 2 &pcie_intc1 1>, -+ <0 0 0 3 &pcie_intc1 2>, -+ <0 0 0 4 &pcie_intc1 3>; -+ pcie_intc1: interrupt-controller { -+ interrupt-controller; -+ #address-cells = <0>; -+ #interrupt-cells = <1>; - }; - }; - diff --git a/target/linux/mediatek/patches-5.15/601-PCI-mediatek-Assert-PERST-for-100ms-for-power-and-cl.patch b/target/linux/mediatek/patches-5.15/601-PCI-mediatek-Assert-PERST-for-100ms-for-power-and-cl.patch deleted file mode 100644 index b7311e042d..0000000000 --- a/target/linux/mediatek/patches-5.15/601-PCI-mediatek-Assert-PERST-for-100ms-for-power-and-cl.patch +++ /dev/null @@ -1,34 +0,0 @@ -From: qizhong cheng -Date: Mon, 27 Dec 2021 21:31:10 +0800 -Subject: [PATCH] PCI: mediatek: Assert PERST# for 100ms for power and clock to - stabilize -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -Described in PCIe CEM specification sections 2.2 (PERST# Signal) and -2.2.1 (Initial Power-Up (G3 to S0)). The deassertion of PERST# should -be delayed 100ms (TPVPERL) for the power and clock to become stable. - -Link: https://lore.kernel.org/r/20211227133110.14500-1-qizhong.cheng@mediatek.com -Signed-off-by: qizhong cheng -Signed-off-by: Lorenzo Pieralisi -Acked-by: Pali Rohár ---- - ---- a/drivers/pci/controller/pcie-mediatek.c -+++ b/drivers/pci/controller/pcie-mediatek.c -@@ -708,6 +708,13 @@ static int mtk_pcie_startup_port_v2(stru - */ - writel(PCIE_LINKDOWN_RST_EN, port->base + PCIE_RST_CTRL); - -+ /* -+ * Described in PCIe CEM specification sections 2.2 (PERST# Signal) and -+ * 2.2.1 (Initial Power-Up (G3 to S0)). The deassertion of PERST# should -+ * be delayed 100ms (TPVPERL) for the power and clock to become stable. -+ */ -+ msleep(100); -+ - /* De-assert PHY, PE, PIPE, MAC and configuration reset */ - val = readl(port->base + PCIE_RST_CTRL); - val |= PCIE_PHY_RSTB | PCIE_PERSTB | PCIE_PIPE_SRSTB | diff --git a/target/linux/mediatek/patches-5.15/602-arm64-dts-mediatek-add-mt7622-pcie-slot-node.patch b/target/linux/mediatek/patches-5.15/602-arm64-dts-mediatek-add-mt7622-pcie-slot-node.patch deleted file mode 100644 index bf479ab53b..0000000000 --- a/target/linux/mediatek/patches-5.15/602-arm64-dts-mediatek-add-mt7622-pcie-slot-node.patch +++ /dev/null @@ -1,28 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi -@@ -849,6 +849,12 @@ - #address-cells = <0>; - #interrupt-cells = <1>; - }; -+ -+ slot0: pcie@0,0 { -+ reg = <0x0000 0 0 0 0>; -+ #address-cells = <3>; -+ #size-cells = <2>; -+ }; - }; - - pcie1: pcie@1a145000 { -@@ -887,6 +893,12 @@ - #address-cells = <0>; - #interrupt-cells = <1>; - }; -+ -+ slot1: pcie@1,0 { -+ reg = <0x0800 0 0 0 0>; -+ #address-cells = <3>; -+ #size-cells = <2>; -+ }; - }; - - sata: sata@1a200000 { diff --git a/target/linux/mediatek/patches-5.15/603-v5.16-ARM-dts-mediatek-Update-mt7629-PCIe-node.patch b/target/linux/mediatek/patches-5.15/603-v5.16-ARM-dts-mediatek-Update-mt7629-PCIe-node.patch deleted file mode 100644 index 252ef080f5..0000000000 --- a/target/linux/mediatek/patches-5.15/603-v5.16-ARM-dts-mediatek-Update-mt7629-PCIe-node.patch +++ /dev/null @@ -1,203 +0,0 @@ -From patchwork Thu May 28 06:16:48 2020 -Content-Type: text/plain; charset="utf-8" -MIME-Version: 1.0 -Content-Transfer-Encoding: 7bit -X-Patchwork-Submitter: Chuanjia Liu -X-Patchwork-Id: 11574797 -Return-Path: - -Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org - [172.30.200.123]) - by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id 30A5E1392 - for ; - Thu, 28 May 2020 06:29:05 +0000 (UTC) -Received: from bombadil.infradead.org (bombadil.infradead.org - [198.137.202.133]) - (using TLSv1.2 with cipher ECDHE-RSA-AES256-GCM-SHA384 (256/256 bits)) - (No client certificate requested) - by mail.kernel.org (Postfix) with ESMTPS id 08B6320721 - for ; - Thu, 28 May 2020 06:29:05 +0000 (UTC) -Authentication-Results: mail.kernel.org; - dkim=pass (2048-bit key) header.d=lists.infradead.org - header.i=@lists.infradead.org header.b="auhxDafY"; - dkim=fail reason="signature verification failed" (1024-bit key) - header.d=mediatek.com header.i=@mediatek.com header.b="Kj09Arxb" -DMARC-Filter: OpenDMARC Filter v1.3.2 mail.kernel.org 08B6320721 -Authentication-Results: mail.kernel.org; - dmarc=fail (p=none dis=none) header.from=mediatek.com -Authentication-Results: mail.kernel.org; - spf=none - smtp.mailfrom=linux-mediatek-bounces+patchwork-linux-mediatek=patchwork.kernel.org@lists.infradead.org -DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; - d=lists.infradead.org; s=bombadil.20170209; h=Sender: - Content-Transfer-Encoding:Content-Type:Cc:List-Subscribe:List-Help:List-Post: - List-Archive:List-Unsubscribe:List-Id:MIME-Version:References:In-Reply-To: - Message-ID:Date:Subject:To:From:Reply-To:Content-ID:Content-Description: - Resent-Date:Resent-From:Resent-Sender:Resent-To:Resent-Cc:Resent-Message-ID: - List-Owner; bh=+QPxF1vlOH7StIZYuXJa3V40x8QVDxCLF9AFXHblB9M=; b=auhxDafYBeaUZO - aYp2KVO8Aie0v4tYtRwBon7hF+x55JwD78SAxQR2RsSvrlOo9cMYYby+ToUWflVUWQ60FapAl+w+l - nkEjIOrLBErHwxNOcsD8T5kjyCBMqlz4OMAQYUDNJ3fSugRlGhOtxkjCGd9ebB8N2Rvu6/U8P1A9n - P15mEQoc+RLonR1+9mBgwTEXErjsraxkimTD4Txsp4IvMs3UdsMkP+r3OT5S/p+Uj6O9ES0h7xIon - aL79KaVqRLHrfZxnrVwuGiecAiTp8qLy9clHuJU32NA6ZcXH1OnWipKApgp8Ck7ys80WPKaMrat9B - XuskJ63w13DZAbCVvuGQ==; -Received: from localhost ([127.0.0.1] helo=bombadil.infradead.org) - by bombadil.infradead.org with esmtp (Exim 4.92.3 #3 (Red Hat Linux)) - id 1jeC2J-00014n-M9; Thu, 28 May 2020 06:29:03 +0000 -Received: from mailgw02.mediatek.com ([216.200.240.185]) - by bombadil.infradead.org with esmtps (Exim 4.92.3 #3 (Red Hat Linux)) - id 1jeC2H-00013t-Li; Thu, 28 May 2020 06:29:03 +0000 -X-UUID: a4877c1586e64afeb2d6172e10605d2b-20200527 -DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; - d=mediatek.com; - s=dk; - h=Content-Transfer-Encoding:Content-Type:MIME-Version:References:In-Reply-To:Message-ID:Date:Subject:CC:To:From; - bh=CIwcBFK1x0LbOjDt1BG6/knHFxDHRiqj8ov/jWEZDBY=; - b=Kj09ArxbnLVTc9bpaVPT3jQrIVjhL87sSYyVF9dFypS976k78Ce9gZd0f4K3zAZbYZHYoQtuyOQ9TOeufQfgD+Cr+j5VR7pTdO2E1iXHFs/eQAz5gAjvjlK01z1JiunrLnn9dvIr6c1gEkjQHny0VpuZ1duxx79jwYusg/Nw6Wc=; -X-UUID: a4877c1586e64afeb2d6172e10605d2b-20200527 -Received: from mtkcas66.mediatek.inc [(172.29.193.44)] by - mailgw02.mediatek.com - (envelope-from ) - (musrelay.mediatek.com ESMTP with TLS) - with ESMTP id 899663677; Wed, 27 May 2020 22:29:21 -0800 -Received: from MTKMBS07N2.mediatek.inc (172.21.101.141) by - MTKMBS62DR.mediatek.inc (172.29.94.18) with Microsoft SMTP Server (TLS) id - 15.0.1497.2; Wed, 27 May 2020 23:18:50 -0700 -Received: from mtkcas07.mediatek.inc (172.21.101.84) by - mtkmbs07n2.mediatek.inc (172.21.101.141) with Microsoft SMTP Server (TLS) id - 15.0.1497.2; Thu, 28 May 2020 14:18:54 +0800 -Received: from localhost.localdomain (10.17.3.153) by mtkcas07.mediatek.inc - (172.21.101.73) with Microsoft SMTP Server id 15.0.1497.2 via Frontend - Transport; Thu, 28 May 2020 14:18:52 +0800 -From: -To: , , -Subject: [PATCH v2 4/4] ARM: dts: mediatek: Update mt7629 PCIe node -Date: Thu, 28 May 2020 14:16:48 +0800 -Message-ID: <20200528061648.32078-5-chuanjia.liu@mediatek.com> -X-Mailer: git-send-email 2.18.0 -In-Reply-To: <20200528061648.32078-1-chuanjia.liu@mediatek.com> -References: <20200528061648.32078-1-chuanjia.liu@mediatek.com> -MIME-Version: 1.0 -X-MTK: N -X-CRM114-Version: 20100106-BlameMichelson ( TRE 0.8.0 (BSD) ) MR-646709E3 -X-CRM114-CacheID: sfid-20200527_232901_719172_E5A99C62 -X-CRM114-Status: GOOD ( 11.61 ) -X-Spam-Score: -0.2 (/) -X-Spam-Report: SpamAssassin version 3.4.4 on bombadil.infradead.org summary: - Content analysis details: (-0.2 points) - pts rule name description - ---- ---------------------- - -------------------------------------------------- - -0.0 SPF_PASS SPF: sender matches SPF record - 0.0 SPF_HELO_NONE SPF: HELO does not publish an SPF Record - 0.0 MIME_BASE64_TEXT RAW: Message text disguised using base64 - encoding - -0.1 DKIM_VALID_AU Message has a valid DKIM or DK signature from - author's domain - 0.1 DKIM_SIGNED Message has a DKIM or DK signature, - not necessarily - valid - -0.1 DKIM_VALID Message has at least one valid DKIM or DK signature - -0.1 DKIM_VALID_EF Message has a valid DKIM or DK signature from - envelope-from domain - 0.0 UNPARSEABLE_RELAY Informational: message has unparseable relay - lines -X-BeenThere: linux-mediatek@lists.infradead.org -X-Mailman-Version: 2.1.29 -Precedence: list -List-Id: -List-Unsubscribe: , - -List-Archive: -List-Post: -List-Help: -List-Subscribe: , - -Cc: devicetree@vger.kernel.org, lorenzo.pieralisi@arm.com, - srv_heupstream@mediatek.com, "chuanjia.liu" , - linux-pci@vger.kernel.org, linux-kernel@vger.kernel.org, - jianjun.wang@mediatek.com, linux-mediatek@lists.infradead.org, - yong.wu@mediatek.com, bhelgaas@google.com, - linux-arm-kernel@lists.infradead.org, amurray@thegoodpenguin.co.uk -Sender: "Linux-mediatek" -Errors-To: - linux-mediatek-bounces+patchwork-linux-mediatek=patchwork.kernel.org@lists.infradead.org - -From: "chuanjia.liu" - -Remove unused property and add pciecfg node. - -Signed-off-by: chuanjia.liu ---- - arch/arm/boot/dts/mt7629-rfb.dts | 3 ++- - arch/arm/boot/dts/mt7629.dtsi | 23 +++++++++++++---------- - 2 files changed, 15 insertions(+), 11 deletions(-) - ---- a/arch/arm/boot/dts/mt7629-rfb.dts -+++ b/arch/arm/boot/dts/mt7629-rfb.dts -@@ -149,9 +149,10 @@ - }; - }; - --&pcie { -+&pcie1 { - pinctrl-names = "default"; - pinctrl-0 = <&pcie_pins>; -+ status = "okay"; - }; - - &pciephy1 { ---- a/arch/arm/boot/dts/mt7629.dtsi -+++ b/arch/arm/boot/dts/mt7629.dtsi -@@ -382,16 +382,21 @@ - #reset-cells = <1>; - }; - -- pcie: pcie@1a140000 { -+ pciecfg: pciecfg@1a140000 { -+ compatible = "mediatek,mt7629-pciecfg", "syscon"; -+ reg = <0x1a140000 0x1000>; -+ }; -+ -+ pcie1: pcie@1a145000 { - compatible = "mediatek,mt7629-pcie"; - device_type = "pci"; -- reg = <0x1a140000 0x1000>, -- <0x1a145000 0x1000>; -- reg-names = "subsys","port1"; -+ reg = <0x1a145000 0x1000>; -+ reg-names = "port1"; -+ mediatek,pcie-cfg = <&pciecfg>; - #address-cells = <3>; - #size-cells = <2>; -- interrupts = , -- ; -+ interrupts = ; -+ interrupt-names = "pcie_irq"; - clocks = <&pciesys CLK_PCIE_P1_MAC_EN>, - <&pciesys CLK_PCIE_P0_AHB_EN>, - <&pciesys CLK_PCIE_P1_AUX_EN>, -@@ -412,21 +417,19 @@ - power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>; - bus-range = <0x00 0xff>; - ranges = <0x82000000 0 0x20000000 0x20000000 0 0x10000000>; -+ status = "disabled"; - -- pcie1: pcie@1,0 { -- device_type = "pci"; -+ slot1: pcie@1,0 { - reg = <0x0800 0 0 0 0>; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - ranges; -- num-lanes = <1>; - interrupt-map-mask = <0 0 0 7>; - interrupt-map = <0 0 0 1 &pcie_intc1 0>, - <0 0 0 2 &pcie_intc1 1>, - <0 0 0 3 &pcie_intc1 2>, - <0 0 0 4 &pcie_intc1 3>; -- - pcie_intc1: interrupt-controller { - interrupt-controller; - #address-cells = <0>; diff --git a/target/linux/mediatek/patches-5.15/610-pcie-mediatek-fix-clearing-interrupt-status.patch b/target/linux/mediatek/patches-5.15/610-pcie-mediatek-fix-clearing-interrupt-status.patch deleted file mode 100644 index 2bebfddf5c..0000000000 --- a/target/linux/mediatek/patches-5.15/610-pcie-mediatek-fix-clearing-interrupt-status.patch +++ /dev/null @@ -1,23 +0,0 @@ -From: Felix Fietkau -Date: Fri, 4 Sep 2020 18:33:27 +0200 -Subject: [PATCH] pcie-mediatek: fix clearing interrupt status - -Clearing the status needs to happen after running the handler, otherwise -we will get an extra spurious interrupt after the cause has been cleared - -Signed-off-by: Felix Fietkau ---- - ---- a/drivers/pci/controller/pcie-mediatek.c -+++ b/drivers/pci/controller/pcie-mediatek.c -@@ -614,9 +614,9 @@ static void mtk_pcie_intr_handler(struct - if (status & INTX_MASK) { - for_each_set_bit_from(bit, &status, PCI_NUM_INTX + INTX_SHIFT) { - /* Clear the INTx */ -- writel(1 << bit, port->base + PCIE_INT_STATUS); - generic_handle_domain_irq(port->irq_domain, - bit - INTX_SHIFT); -+ writel(1 << bit, port->base + PCIE_INT_STATUS); - } - } - diff --git a/target/linux/mediatek/patches-5.15/611-pcie-mediatek-gen3-PERST-for-100ms.patch b/target/linux/mediatek/patches-5.15/611-pcie-mediatek-gen3-PERST-for-100ms.patch deleted file mode 100644 index d526aded85..0000000000 --- a/target/linux/mediatek/patches-5.15/611-pcie-mediatek-gen3-PERST-for-100ms.patch +++ /dev/null @@ -1,17 +0,0 @@ ---- a/drivers/pci/controller/pcie-mediatek-gen3.c -+++ b/drivers/pci/controller/pcie-mediatek-gen3.c -@@ -319,7 +319,13 @@ static int mtk_pcie_startup_port(struct - msleep(100); - - /* De-assert reset signals */ -- val &= ~(PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB | PCIE_PE_RSTB); -+ val &= ~(PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB); -+ writel_relaxed(val, port->base + PCIE_RST_CTRL_REG); -+ -+ msleep(100); -+ -+ /* De-assert PERST# signals */ -+ val &= ~(PCIE_PE_RSTB); - writel_relaxed(val, port->base + PCIE_RST_CTRL_REG); - - /* Check if the link is up or not */ diff --git a/target/linux/mediatek/patches-5.15/702-v5.17-net-mdio-add-helpers-to-extract-clause-45-regad-and-.patch b/target/linux/mediatek/patches-5.15/702-v5.17-net-mdio-add-helpers-to-extract-clause-45-regad-and-.patch deleted file mode 100644 index da33aaa72f..0000000000 --- a/target/linux/mediatek/patches-5.15/702-v5.17-net-mdio-add-helpers-to-extract-clause-45-regad-and-.patch +++ /dev/null @@ -1,53 +0,0 @@ -From c6af53f038aa32cec12e8a305ba07c7ef168f1b0 Mon Sep 17 00:00:00 2001 -From: "Russell King (Oracle)" -Date: Tue, 4 Jan 2022 12:07:00 +0000 -Subject: [PATCH 2/3] net: mdio: add helpers to extract clause 45 regad and - devad fields - -Add a couple of helpers and definitions to extract the clause 45 regad -and devad fields from the regnum passed into MDIO drivers. - -Tested-by: Daniel Golle -Reviewed-by: Andrew Lunn -Signed-off-by: Russell King (Oracle) -Signed-off-by: Daniel Golle -Signed-off-by: David S. Miller ---- - include/linux/mdio.h | 12 ++++++++++++ - 1 file changed, 12 insertions(+) - ---- a/include/linux/mdio.h -+++ b/include/linux/mdio.h -@@ -7,6 +7,7 @@ - #define __LINUX_MDIO_H__ - - #include -+#include - #include - - /* Or MII_ADDR_C45 into regnum for read/write on mii_bus to enable the 21 bit -@@ -14,6 +15,7 @@ - */ - #define MII_ADDR_C45 (1<<30) - #define MII_DEVADDR_C45_SHIFT 16 -+#define MII_DEVADDR_C45_MASK GENMASK(20, 16) - #define MII_REGADDR_C45_MASK GENMASK(15, 0) - - struct gpio_desc; -@@ -355,6 +357,16 @@ static inline u32 mdiobus_c45_addr(int d - return MII_ADDR_C45 | devad << MII_DEVADDR_C45_SHIFT | regnum; - } - -+static inline u16 mdiobus_c45_regad(u32 regnum) -+{ -+ return FIELD_GET(MII_REGADDR_C45_MASK, regnum); -+} -+ -+static inline u16 mdiobus_c45_devad(u32 regnum) -+{ -+ return FIELD_GET(MII_DEVADDR_C45_MASK, regnum); -+} -+ - static inline int __mdiobus_c45_read(struct mii_bus *bus, int prtad, int devad, - u16 regnum) - { diff --git a/target/linux/mediatek/patches-5.15/703-v5.17-net-ethernet-mtk_eth_soc-implement-Clause-45-MDIO-ac.patch b/target/linux/mediatek/patches-5.15/703-v5.17-net-ethernet-mtk_eth_soc-implement-Clause-45-MDIO-ac.patch deleted file mode 100644 index 3f73277aa6..0000000000 --- a/target/linux/mediatek/patches-5.15/703-v5.17-net-ethernet-mtk_eth_soc-implement-Clause-45-MDIO-ac.patch +++ /dev/null @@ -1,128 +0,0 @@ -From e2e7f6e29c99a1c6afc0e0aa4b9ea80302d28720 Mon Sep 17 00:00:00 2001 -From: Daniel Golle -Date: Tue, 4 Jan 2022 12:07:46 +0000 -Subject: [PATCH 3/3] net: ethernet: mtk_eth_soc: implement Clause 45 MDIO - access - -Implement read and write access to IEEE 802.3 Clause 45 Ethernet -phy registers while making use of new mdiobus_c45_regad and -mdiobus_c45_devad helpers. - -Tested on the Ubiquiti UniFi 6 LR access point featuring -MediaTek MT7622BV WiSoC with Aquantia AQR112C. - -Signed-off-by: Daniel Golle -Signed-off-by: David S. Miller ---- - drivers/net/ethernet/mediatek/mtk_eth_soc.c | 70 +++++++++++++++++---- - drivers/net/ethernet/mediatek/mtk_eth_soc.h | 3 + - 2 files changed, 60 insertions(+), 13 deletions(-) - ---- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c -+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c -@@ -324,13 +324,35 @@ static int _mtk_mdio_write(struct mtk_et - if (ret < 0) - return ret; - -- mtk_w32(eth, PHY_IAC_ACCESS | -- PHY_IAC_START_C22 | -- PHY_IAC_CMD_WRITE | -- PHY_IAC_REG(phy_reg) | -- PHY_IAC_ADDR(phy_addr) | -- PHY_IAC_DATA(write_data), -- MTK_PHY_IAC); -+ if (phy_reg & MII_ADDR_C45) { -+ mtk_w32(eth, PHY_IAC_ACCESS | -+ PHY_IAC_START_C45 | -+ PHY_IAC_CMD_C45_ADDR | -+ PHY_IAC_REG(mdiobus_c45_devad(phy_reg)) | -+ PHY_IAC_ADDR(phy_addr) | -+ PHY_IAC_DATA(mdiobus_c45_regad(phy_reg)), -+ MTK_PHY_IAC); -+ -+ ret = mtk_mdio_busy_wait(eth); -+ if (ret < 0) -+ return ret; -+ -+ mtk_w32(eth, PHY_IAC_ACCESS | -+ PHY_IAC_START_C45 | -+ PHY_IAC_CMD_WRITE | -+ PHY_IAC_REG(mdiobus_c45_devad(phy_reg)) | -+ PHY_IAC_ADDR(phy_addr) | -+ PHY_IAC_DATA(write_data), -+ MTK_PHY_IAC); -+ } else { -+ mtk_w32(eth, PHY_IAC_ACCESS | -+ PHY_IAC_START_C22 | -+ PHY_IAC_CMD_WRITE | -+ PHY_IAC_REG(phy_reg) | -+ PHY_IAC_ADDR(phy_addr) | -+ PHY_IAC_DATA(write_data), -+ MTK_PHY_IAC); -+ } - - ret = mtk_mdio_busy_wait(eth); - if (ret < 0) -@@ -347,12 +369,33 @@ static int _mtk_mdio_read(struct mtk_eth - if (ret < 0) - return ret; - -- mtk_w32(eth, PHY_IAC_ACCESS | -- PHY_IAC_START_C22 | -- PHY_IAC_CMD_C22_READ | -- PHY_IAC_REG(phy_reg) | -- PHY_IAC_ADDR(phy_addr), -- MTK_PHY_IAC); -+ if (phy_reg & MII_ADDR_C45) { -+ mtk_w32(eth, PHY_IAC_ACCESS | -+ PHY_IAC_START_C45 | -+ PHY_IAC_CMD_C45_ADDR | -+ PHY_IAC_REG(mdiobus_c45_devad(phy_reg)) | -+ PHY_IAC_ADDR(phy_addr) | -+ PHY_IAC_DATA(mdiobus_c45_regad(phy_reg)), -+ MTK_PHY_IAC); -+ -+ ret = mtk_mdio_busy_wait(eth); -+ if (ret < 0) -+ return ret; -+ -+ mtk_w32(eth, PHY_IAC_ACCESS | -+ PHY_IAC_START_C45 | -+ PHY_IAC_CMD_C45_READ | -+ PHY_IAC_REG(mdiobus_c45_devad(phy_reg)) | -+ PHY_IAC_ADDR(phy_addr), -+ MTK_PHY_IAC); -+ } else { -+ mtk_w32(eth, PHY_IAC_ACCESS | -+ PHY_IAC_START_C22 | -+ PHY_IAC_CMD_C22_READ | -+ PHY_IAC_REG(phy_reg) | -+ PHY_IAC_ADDR(phy_addr), -+ MTK_PHY_IAC); -+ } - - ret = mtk_mdio_busy_wait(eth); - if (ret < 0) -@@ -899,6 +942,7 @@ static int mtk_mdio_init(struct mtk_eth - eth->mii_bus->name = "mdio"; - eth->mii_bus->read = mtk_mdio_read; - eth->mii_bus->write = mtk_mdio_write; -+ eth->mii_bus->probe_capabilities = MDIOBUS_C22_C45; - eth->mii_bus->priv = eth; - eth->mii_bus->parent = eth->dev; - ---- a/drivers/net/ethernet/mediatek/mtk_eth_soc.h -+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.h -@@ -402,9 +402,12 @@ - #define PHY_IAC_ADDR_MASK GENMASK(24, 20) - #define PHY_IAC_ADDR(x) FIELD_PREP(PHY_IAC_ADDR_MASK, (x)) - #define PHY_IAC_CMD_MASK GENMASK(19, 18) -+#define PHY_IAC_CMD_C45_ADDR FIELD_PREP(PHY_IAC_CMD_MASK, 0) - #define PHY_IAC_CMD_WRITE FIELD_PREP(PHY_IAC_CMD_MASK, 1) - #define PHY_IAC_CMD_C22_READ FIELD_PREP(PHY_IAC_CMD_MASK, 2) -+#define PHY_IAC_CMD_C45_READ FIELD_PREP(PHY_IAC_CMD_MASK, 3) - #define PHY_IAC_START_MASK GENMASK(17, 16) -+#define PHY_IAC_START_C45 FIELD_PREP(PHY_IAC_START_MASK, 0) - #define PHY_IAC_START_C22 FIELD_PREP(PHY_IAC_START_MASK, 1) - #define PHY_IAC_DATA_MASK GENMASK(15, 0) - #define PHY_IAC_DATA(x) FIELD_PREP(PHY_IAC_DATA_MASK, (x)) diff --git a/target/linux/mediatek/patches-5.15/710-pci-pcie-mediatek-add-support-for-coherent-DMA.patch b/target/linux/mediatek/patches-5.15/710-pci-pcie-mediatek-add-support-for-coherent-DMA.patch deleted file mode 100644 index 76ee2fc89a..0000000000 --- a/target/linux/mediatek/patches-5.15/710-pci-pcie-mediatek-add-support-for-coherent-DMA.patch +++ /dev/null @@ -1,82 +0,0 @@ -From: Felix Fietkau -Date: Fri, 4 Sep 2020 18:42:42 +0200 -Subject: [PATCH] pci: pcie-mediatek: add support for coherent DMA - -It improves performance by eliminating the need for a cache flush for DMA on -attached devices - -Signed-off-by: Felix Fietkau ---- - ---- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi -@@ -837,6 +837,9 @@ - bus-range = <0x00 0xff>; - ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x8000000>; - status = "disabled"; -+ dma-coherent; -+ mediatek,hifsys = <&hifsys>; -+ mediatek,cci-control = <&cci_control2>; - - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 7>; -@@ -881,6 +884,9 @@ - bus-range = <0x00 0xff>; - ranges = <0x82000000 0 0x28000000 0x0 0x28000000 0 0x8000000>; - status = "disabled"; -+ dma-coherent; -+ mediatek,hifsys = <&hifsys>; -+ mediatek,cci-control = <&cci_control2>; - - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 7>; ---- a/drivers/pci/controller/pcie-mediatek.c -+++ b/drivers/pci/controller/pcie-mediatek.c -@@ -20,6 +20,7 @@ - #include - #include - #include -+#include - #include - #include - #include -@@ -139,6 +140,11 @@ - #define PCIE_LINK_STATUS_V2 0x804 - #define PCIE_PORT_LINKUP_V2 BIT(10) - -+/* DMA channel mapping */ -+#define HIFSYS_DMA_AG_MAP 0x008 -+#define HIFSYS_DMA_AG_MAP_PCIE0 BIT(0) -+#define HIFSYS_DMA_AG_MAP_PCIE1 BIT(1) -+ - struct mtk_pcie_port; - - /** -@@ -1060,6 +1066,27 @@ static int mtk_pcie_setup(struct mtk_pci - struct mtk_pcie_port *port, *tmp; - int err, slot; - -+ if (of_dma_is_coherent(node)) { -+ struct regmap *con; -+ u32 mask; -+ -+ con = syscon_regmap_lookup_by_phandle(node, -+ "mediatek,cci-control"); -+ /* enable CPU/bus coherency */ -+ if (!IS_ERR(con)) -+ regmap_write(con, 0, 3); -+ -+ con = syscon_regmap_lookup_by_phandle(node, -+ "mediatek,hifsys"); -+ if (IS_ERR(con)) { -+ dev_err(dev, "missing hifsys node\n"); -+ return PTR_ERR(con); -+ } -+ -+ mask = HIFSYS_DMA_AG_MAP_PCIE0 | HIFSYS_DMA_AG_MAP_PCIE1; -+ regmap_update_bits(con, HIFSYS_DMA_AG_MAP, mask, mask); -+ } -+ - slot = of_get_pci_domain_nr(dev->of_node); - if (slot < 0) { - for_each_available_child_of_node(node, child) { diff --git a/target/linux/mediatek/patches-5.15/721-dts-mt7622-mediatek-fix-300mhz.patch b/target/linux/mediatek/patches-5.15/721-dts-mt7622-mediatek-fix-300mhz.patch deleted file mode 100644 index f9a5fdbd0d..0000000000 --- a/target/linux/mediatek/patches-5.15/721-dts-mt7622-mediatek-fix-300mhz.patch +++ /dev/null @@ -1,27 +0,0 @@ -From: Jip de Beer -Date: Sun, 9 Jan 2022 13:14:04 +0100 -Subject: [PATCH] mediatek mt7622: fix 300mhz typo in dts - -The lowest frequency should be 300MHz, since that is the label -assigned to the OPP in the mt7622.dtsi device tree, while there is one -missing zero in the actual value. - -To be clear, the lowest frequency should be 300MHz instead of 30MHz. - -As mentioned @dangowrt on the OpenWrt forum there is no benefit in -leaving 30MHz as the lowest frequency. - -Signed-off-by: Jip de Beer -Signed-off-by: Fritz D. Ansel ---- ---- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi -@@ -24,7 +24,7 @@ - compatible = "operating-points-v2"; - opp-shared; - opp-300000000 { -- opp-hz = /bits/ 64 <30000000>; -+ opp-hz = /bits/ 64 <300000000>; - opp-microvolt = <950000>; - }; - diff --git a/target/linux/mediatek/patches-5.15/722-remove-300Hz-to-prevent-freeze.patch b/target/linux/mediatek/patches-5.15/722-remove-300Hz-to-prevent-freeze.patch deleted file mode 100644 index 52069496ca..0000000000 --- a/target/linux/mediatek/patches-5.15/722-remove-300Hz-to-prevent-freeze.patch +++ /dev/null @@ -1,25 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi -@@ -23,11 +23,17 @@ - cpu_opp_table: opp-table { - compatible = "operating-points-v2"; - opp-shared; -- opp-300000000 { -- opp-hz = /bits/ 64 <300000000>; -- opp-microvolt = <950000>; -- }; -- -+ /* Due to the bug described at the link below, remove the 300 MHz clock to avoid a low -+ * voltage condition that can cause a hang when rebooting the RT3200/E8450. -+ * -+ * https://forum.openwrt.org/t/belkin-rt3200-linksys-e8450-wifi-ax-discussion/94302/1490 -+ * -+ * opp-300000000 { -+ * opp-hz = /bits/ 64 <300000000>; -+ * opp-microvolt = <950000>; -+ * }; -+ * -+ */ - opp-437500000 { - opp-hz = /bits/ 64 <437500000>; - opp-microvolt = <1000000>; diff --git a/target/linux/mediatek/patches-5.15/730-v6.5-net-phy-add-driver-for-MediaTek-SoC-built-in-GE-PHYs.patch b/target/linux/mediatek/patches-5.15/730-v6.5-net-phy-add-driver-for-MediaTek-SoC-built-in-GE-PHYs.patch deleted file mode 100644 index 72ad2a9846..0000000000 --- a/target/linux/mediatek/patches-5.15/730-v6.5-net-phy-add-driver-for-MediaTek-SoC-built-in-GE-PHYs.patch +++ /dev/null @@ -1,1204 +0,0 @@ -From 98c485eaf509bc0e2a85f9b58d17cd501f274c4e Mon Sep 17 00:00:00 2001 -From: Daniel Golle -Date: Sun, 11 Jun 2023 00:48:10 +0100 -Subject: [PATCH] net: phy: add driver for MediaTek SoC built-in GE PHYs - -Some of MediaTek's Filogic SoCs come with built-in gigabit Ethernet -PHYs which require calibration data from the SoC's efuse. -Despite the similar design the driver doesn't share any code with the -existing mediatek-ge.c. -Add support for such PHYs by introducing a new driver with basic -support for MediaTek SoCs MT7981 and MT7988 built-in 1GE PHYs. - -Signed-off-by: Daniel Golle -Reviewed-by: Andrew Lunn -Signed-off-by: David S. Miller ---- - MAINTAINERS | 9 + - drivers/net/phy/Kconfig | 12 + - drivers/net/phy/Makefile | 1 + - drivers/net/phy/mediatek-ge-soc.c | 1116 +++++++++++++++++++++++++++++ - drivers/net/phy/mediatek-ge.c | 3 +- - 5 files changed, 1140 insertions(+), 1 deletion(-) - create mode 100644 drivers/net/phy/mediatek-ge-soc.c - ---- a/MAINTAINERS -+++ b/MAINTAINERS -@@ -11791,6 +11791,15 @@ S: Maintained - F: drivers/net/pcs/pcs-mtk-lynxi.c - F: include/linux/pcs/pcs-mtk-lynxi.h - -+MEDIATEK ETHERNET PHY DRIVERS -+M: Daniel Golle -+M: Qingfang Deng -+M: SkyLake Huang -+L: netdev@vger.kernel.org -+S: Maintained -+F: drivers/net/phy/mediatek-ge-soc.c -+F: drivers/net/phy/mediatek-ge.c -+ - MEDIATEK I2C CONTROLLER DRIVER - M: Qii Wang - L: linux-i2c@vger.kernel.org ---- a/drivers/net/phy/Kconfig -+++ b/drivers/net/phy/Kconfig -@@ -290,6 +290,18 @@ config MEDIATEK_GE_PHY - help - Supports the MediaTek Gigabit Ethernet PHYs. - -+config MEDIATEK_GE_SOC_PHY -+ tristate "MediaTek SoC Ethernet PHYs" -+ depends on (ARM64 && ARCH_MEDIATEK) || COMPILE_TEST -+ select NVMEM_MTK_EFUSE -+ help -+ Supports MediaTek SoC built-in Gigabit Ethernet PHYs. -+ -+ Include support for built-in Ethernet PHYs which are present in -+ the MT7981 and MT7988 SoCs. These PHYs need calibration data -+ present in the SoCs efuse and will dynamically calibrate VCM -+ (common-mode voltage) during startup. -+ - config MICREL_PHY - tristate "Micrel PHYs" - help ---- a/drivers/net/phy/Makefile -+++ b/drivers/net/phy/Makefile -@@ -77,6 +77,7 @@ obj-$(CONFIG_MARVELL_PHY) += marvell.o - obj-$(CONFIG_MARVELL_88X2222_PHY) += marvell-88x2222.o - obj-$(CONFIG_MAXLINEAR_GPHY) += mxl-gpy.o - obj-$(CONFIG_MEDIATEK_GE_PHY) += mediatek-ge.o -+obj-$(CONFIG_MEDIATEK_GE_SOC_PHY) += mediatek-ge-soc.o - obj-$(CONFIG_MESON_GXL_PHY) += meson-gxl.o - obj-$(CONFIG_MICREL_KS8995MA) += spi_ks8995.o - obj-$(CONFIG_MICREL_PHY) += micrel.o ---- /dev/null -+++ b/drivers/net/phy/mediatek-ge-soc.c -@@ -0,0 +1,1116 @@ -+// SPDX-License-Identifier: GPL-2.0+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#define MTK_GPHY_ID_MT7981 0x03a29461 -+#define MTK_GPHY_ID_MT7988 0x03a29481 -+ -+#define MTK_EXT_PAGE_ACCESS 0x1f -+#define MTK_PHY_PAGE_STANDARD 0x0000 -+#define MTK_PHY_PAGE_EXTENDED_3 0x0003 -+ -+#define MTK_PHY_LPI_REG_14 0x14 -+#define MTK_PHY_LPI_WAKE_TIMER_1000_MASK GENMASK(8, 0) -+ -+#define MTK_PHY_LPI_REG_1c 0x1c -+#define MTK_PHY_SMI_DET_ON_THRESH_MASK GENMASK(13, 8) -+ -+#define MTK_PHY_PAGE_EXTENDED_2A30 0x2a30 -+#define MTK_PHY_PAGE_EXTENDED_52B5 0x52b5 -+ -+#define ANALOG_INTERNAL_OPERATION_MAX_US 20 -+#define TXRESERVE_MIN 0 -+#define TXRESERVE_MAX 7 -+ -+#define MTK_PHY_ANARG_RG 0x10 -+#define MTK_PHY_TCLKOFFSET_MASK GENMASK(12, 8) -+ -+/* Registers on MDIO_MMD_VEND1 */ -+#define MTK_PHY_TXVLD_DA_RG 0x12 -+#define MTK_PHY_DA_TX_I2MPB_A_GBE_MASK GENMASK(15, 10) -+#define MTK_PHY_DA_TX_I2MPB_A_TBT_MASK GENMASK(5, 0) -+ -+#define MTK_PHY_TX_I2MPB_TEST_MODE_A2 0x16 -+#define MTK_PHY_DA_TX_I2MPB_A_HBT_MASK GENMASK(15, 10) -+#define MTK_PHY_DA_TX_I2MPB_A_TST_MASK GENMASK(5, 0) -+ -+#define MTK_PHY_TX_I2MPB_TEST_MODE_B1 0x17 -+#define MTK_PHY_DA_TX_I2MPB_B_GBE_MASK GENMASK(13, 8) -+#define MTK_PHY_DA_TX_I2MPB_B_TBT_MASK GENMASK(5, 0) -+ -+#define MTK_PHY_TX_I2MPB_TEST_MODE_B2 0x18 -+#define MTK_PHY_DA_TX_I2MPB_B_HBT_MASK GENMASK(13, 8) -+#define MTK_PHY_DA_TX_I2MPB_B_TST_MASK GENMASK(5, 0) -+ -+#define MTK_PHY_TX_I2MPB_TEST_MODE_C1 0x19 -+#define MTK_PHY_DA_TX_I2MPB_C_GBE_MASK GENMASK(13, 8) -+#define MTK_PHY_DA_TX_I2MPB_C_TBT_MASK GENMASK(5, 0) -+ -+#define MTK_PHY_TX_I2MPB_TEST_MODE_C2 0x20 -+#define MTK_PHY_DA_TX_I2MPB_C_HBT_MASK GENMASK(13, 8) -+#define MTK_PHY_DA_TX_I2MPB_C_TST_MASK GENMASK(5, 0) -+ -+#define MTK_PHY_TX_I2MPB_TEST_MODE_D1 0x21 -+#define MTK_PHY_DA_TX_I2MPB_D_GBE_MASK GENMASK(13, 8) -+#define MTK_PHY_DA_TX_I2MPB_D_TBT_MASK GENMASK(5, 0) -+ -+#define MTK_PHY_TX_I2MPB_TEST_MODE_D2 0x22 -+#define MTK_PHY_DA_TX_I2MPB_D_HBT_MASK GENMASK(13, 8) -+#define MTK_PHY_DA_TX_I2MPB_D_TST_MASK GENMASK(5, 0) -+ -+#define MTK_PHY_RXADC_CTRL_RG7 0xc6 -+#define MTK_PHY_DA_AD_BUF_BIAS_LP_MASK GENMASK(9, 8) -+ -+#define MTK_PHY_RXADC_CTRL_RG9 0xc8 -+#define MTK_PHY_DA_RX_PSBN_TBT_MASK GENMASK(14, 12) -+#define MTK_PHY_DA_RX_PSBN_HBT_MASK GENMASK(10, 8) -+#define MTK_PHY_DA_RX_PSBN_GBE_MASK GENMASK(6, 4) -+#define MTK_PHY_DA_RX_PSBN_LP_MASK GENMASK(2, 0) -+ -+#define MTK_PHY_LDO_OUTPUT_V 0xd7 -+ -+#define MTK_PHY_RG_ANA_CAL_RG0 0xdb -+#define MTK_PHY_RG_CAL_CKINV BIT(12) -+#define MTK_PHY_RG_ANA_CALEN BIT(8) -+#define MTK_PHY_RG_ZCALEN_A BIT(0) -+ -+#define MTK_PHY_RG_ANA_CAL_RG1 0xdc -+#define MTK_PHY_RG_ZCALEN_B BIT(12) -+#define MTK_PHY_RG_ZCALEN_C BIT(8) -+#define MTK_PHY_RG_ZCALEN_D BIT(4) -+#define MTK_PHY_RG_TXVOS_CALEN BIT(0) -+ -+#define MTK_PHY_RG_ANA_CAL_RG5 0xe0 -+#define MTK_PHY_RG_REXT_TRIM_MASK GENMASK(13, 8) -+ -+#define MTK_PHY_RG_TX_FILTER 0xfe -+ -+#define MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG120 0x120 -+#define MTK_PHY_LPI_SIG_EN_LO_THRESH1000_MASK GENMASK(12, 8) -+#define MTK_PHY_LPI_SIG_EN_HI_THRESH1000_MASK GENMASK(4, 0) -+ -+#define MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG122 0x122 -+#define MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK GENMASK(7, 0) -+ -+#define MTK_PHY_RG_TESTMUX_ADC_CTRL 0x144 -+#define MTK_PHY_RG_TXEN_DIG_MASK GENMASK(5, 5) -+ -+#define MTK_PHY_RG_CR_TX_AMP_OFFSET_A_B 0x172 -+#define MTK_PHY_CR_TX_AMP_OFFSET_A_MASK GENMASK(13, 8) -+#define MTK_PHY_CR_TX_AMP_OFFSET_B_MASK GENMASK(6, 0) -+ -+#define MTK_PHY_RG_CR_TX_AMP_OFFSET_C_D 0x173 -+#define MTK_PHY_CR_TX_AMP_OFFSET_C_MASK GENMASK(13, 8) -+#define MTK_PHY_CR_TX_AMP_OFFSET_D_MASK GENMASK(6, 0) -+ -+#define MTK_PHY_RG_AD_CAL_COMP 0x17a -+#define MTK_PHY_AD_CAL_COMP_OUT_SHIFT (8) -+ -+#define MTK_PHY_RG_AD_CAL_CLK 0x17b -+#define MTK_PHY_DA_CAL_CLK BIT(0) -+ -+#define MTK_PHY_RG_AD_CALIN 0x17c -+#define MTK_PHY_DA_CALIN_FLAG BIT(0) -+ -+#define MTK_PHY_RG_DASN_DAC_IN0_A 0x17d -+#define MTK_PHY_DASN_DAC_IN0_A_MASK GENMASK(9, 0) -+ -+#define MTK_PHY_RG_DASN_DAC_IN0_B 0x17e -+#define MTK_PHY_DASN_DAC_IN0_B_MASK GENMASK(9, 0) -+ -+#define MTK_PHY_RG_DASN_DAC_IN0_C 0x17f -+#define MTK_PHY_DASN_DAC_IN0_C_MASK GENMASK(9, 0) -+ -+#define MTK_PHY_RG_DASN_DAC_IN0_D 0x180 -+#define MTK_PHY_DASN_DAC_IN0_D_MASK GENMASK(9, 0) -+ -+#define MTK_PHY_RG_DASN_DAC_IN1_A 0x181 -+#define MTK_PHY_DASN_DAC_IN1_A_MASK GENMASK(9, 0) -+ -+#define MTK_PHY_RG_DASN_DAC_IN1_B 0x182 -+#define MTK_PHY_DASN_DAC_IN1_B_MASK GENMASK(9, 0) -+ -+#define MTK_PHY_RG_DASN_DAC_IN1_C 0x183 -+#define MTK_PHY_DASN_DAC_IN1_C_MASK GENMASK(9, 0) -+ -+#define MTK_PHY_RG_DASN_DAC_IN1_D 0x184 -+#define MTK_PHY_DASN_DAC_IN1_D_MASK GENMASK(9, 0) -+ -+#define MTK_PHY_RG_DEV1E_REG19b 0x19b -+#define MTK_PHY_BYPASS_DSP_LPI_READY BIT(8) -+ -+#define MTK_PHY_RG_LP_IIR2_K1_L 0x22a -+#define MTK_PHY_RG_LP_IIR2_K1_U 0x22b -+#define MTK_PHY_RG_LP_IIR2_K2_L 0x22c -+#define MTK_PHY_RG_LP_IIR2_K2_U 0x22d -+#define MTK_PHY_RG_LP_IIR2_K3_L 0x22e -+#define MTK_PHY_RG_LP_IIR2_K3_U 0x22f -+#define MTK_PHY_RG_LP_IIR2_K4_L 0x230 -+#define MTK_PHY_RG_LP_IIR2_K4_U 0x231 -+#define MTK_PHY_RG_LP_IIR2_K5_L 0x232 -+#define MTK_PHY_RG_LP_IIR2_K5_U 0x233 -+ -+#define MTK_PHY_RG_DEV1E_REG234 0x234 -+#define MTK_PHY_TR_OPEN_LOOP_EN_MASK GENMASK(0, 0) -+#define MTK_PHY_LPF_X_AVERAGE_MASK GENMASK(7, 4) -+#define MTK_PHY_TR_LP_IIR_EEE_EN BIT(12) -+ -+#define MTK_PHY_RG_LPF_CNT_VAL 0x235 -+ -+#define MTK_PHY_RG_DEV1E_REG238 0x238 -+#define MTK_PHY_LPI_SLV_SEND_TX_TIMER_MASK GENMASK(8, 0) -+#define MTK_PHY_LPI_SLV_SEND_TX_EN BIT(12) -+ -+#define MTK_PHY_RG_DEV1E_REG239 0x239 -+#define MTK_PHY_LPI_SEND_LOC_TIMER_MASK GENMASK(8, 0) -+#define MTK_PHY_LPI_TXPCS_LOC_RCV BIT(12) -+ -+#define MTK_PHY_RG_DEV1E_REG27C 0x27c -+#define MTK_PHY_VGASTATE_FFE_THR_ST1_MASK GENMASK(12, 8) -+#define MTK_PHY_RG_DEV1E_REG27D 0x27d -+#define MTK_PHY_VGASTATE_FFE_THR_ST2_MASK GENMASK(4, 0) -+ -+#define MTK_PHY_RG_DEV1E_REG2C7 0x2c7 -+#define MTK_PHY_MAX_GAIN_MASK GENMASK(4, 0) -+#define MTK_PHY_MIN_GAIN_MASK GENMASK(12, 8) -+ -+#define MTK_PHY_RG_DEV1E_REG2D1 0x2d1 -+#define MTK_PHY_VCO_SLICER_THRESH_BITS_HIGH_EEE_MASK GENMASK(7, 0) -+#define MTK_PHY_LPI_SKIP_SD_SLV_TR BIT(8) -+#define MTK_PHY_LPI_TR_READY BIT(9) -+#define MTK_PHY_LPI_VCO_EEE_STG0_EN BIT(10) -+ -+#define MTK_PHY_RG_DEV1E_REG323 0x323 -+#define MTK_PHY_EEE_WAKE_MAS_INT_DC BIT(0) -+#define MTK_PHY_EEE_WAKE_SLV_INT_DC BIT(4) -+ -+#define MTK_PHY_RG_DEV1E_REG324 0x324 -+#define MTK_PHY_SMI_DETCNT_MAX_MASK GENMASK(5, 0) -+#define MTK_PHY_SMI_DET_MAX_EN BIT(8) -+ -+#define MTK_PHY_RG_DEV1E_REG326 0x326 -+#define MTK_PHY_LPI_MODE_SD_ON BIT(0) -+#define MTK_PHY_RESET_RANDUPD_CNT BIT(1) -+#define MTK_PHY_TREC_UPDATE_ENAB_CLR BIT(2) -+#define MTK_PHY_LPI_QUIT_WAIT_DFE_SIG_DET_OFF BIT(4) -+#define MTK_PHY_TR_READY_SKIP_AFE_WAKEUP BIT(5) -+ -+#define MTK_PHY_LDO_PUMP_EN_PAIRAB 0x502 -+#define MTK_PHY_LDO_PUMP_EN_PAIRCD 0x503 -+ -+#define MTK_PHY_DA_TX_R50_PAIR_A 0x53d -+#define MTK_PHY_DA_TX_R50_PAIR_B 0x53e -+#define MTK_PHY_DA_TX_R50_PAIR_C 0x53f -+#define MTK_PHY_DA_TX_R50_PAIR_D 0x540 -+ -+#define MTK_PHY_RG_BG_RASEL 0x115 -+#define MTK_PHY_RG_BG_RASEL_MASK GENMASK(2, 0) -+ -+/* These macro privides efuse parsing for internal phy. */ -+#define EFS_DA_TX_I2MPB_A(x) (((x) >> 0) & GENMASK(5, 0)) -+#define EFS_DA_TX_I2MPB_B(x) (((x) >> 6) & GENMASK(5, 0)) -+#define EFS_DA_TX_I2MPB_C(x) (((x) >> 12) & GENMASK(5, 0)) -+#define EFS_DA_TX_I2MPB_D(x) (((x) >> 18) & GENMASK(5, 0)) -+#define EFS_DA_TX_AMP_OFFSET_A(x) (((x) >> 24) & GENMASK(5, 0)) -+ -+#define EFS_DA_TX_AMP_OFFSET_B(x) (((x) >> 0) & GENMASK(5, 0)) -+#define EFS_DA_TX_AMP_OFFSET_C(x) (((x) >> 6) & GENMASK(5, 0)) -+#define EFS_DA_TX_AMP_OFFSET_D(x) (((x) >> 12) & GENMASK(5, 0)) -+#define EFS_DA_TX_R50_A(x) (((x) >> 18) & GENMASK(5, 0)) -+#define EFS_DA_TX_R50_B(x) (((x) >> 24) & GENMASK(5, 0)) -+ -+#define EFS_DA_TX_R50_C(x) (((x) >> 0) & GENMASK(5, 0)) -+#define EFS_DA_TX_R50_D(x) (((x) >> 6) & GENMASK(5, 0)) -+ -+#define EFS_RG_BG_RASEL(x) (((x) >> 4) & GENMASK(2, 0)) -+#define EFS_RG_REXT_TRIM(x) (((x) >> 7) & GENMASK(5, 0)) -+ -+enum { -+ NO_PAIR, -+ PAIR_A, -+ PAIR_B, -+ PAIR_C, -+ PAIR_D, -+}; -+ -+enum { -+ GPHY_PORT0, -+ GPHY_PORT1, -+ GPHY_PORT2, -+ GPHY_PORT3, -+}; -+ -+enum calibration_mode { -+ EFUSE_K, -+ SW_K -+}; -+ -+enum CAL_ITEM { -+ REXT, -+ TX_OFFSET, -+ TX_AMP, -+ TX_R50, -+ TX_VCM -+}; -+ -+enum CAL_MODE { -+ EFUSE_M, -+ SW_M -+}; -+ -+static int mtk_socphy_read_page(struct phy_device *phydev) -+{ -+ return __phy_read(phydev, MTK_EXT_PAGE_ACCESS); -+} -+ -+static int mtk_socphy_write_page(struct phy_device *phydev, int page) -+{ -+ return __phy_write(phydev, MTK_EXT_PAGE_ACCESS, page); -+} -+ -+/* One calibration cycle consists of: -+ * 1.Set DA_CALIN_FLAG high to start calibration. Keep it high -+ * until AD_CAL_COMP is ready to output calibration result. -+ * 2.Wait until DA_CAL_CLK is available. -+ * 3.Fetch AD_CAL_COMP_OUT. -+ */ -+static int cal_cycle(struct phy_device *phydev, int devad, -+ u32 regnum, u16 mask, u16 cal_val) -+{ -+ int reg_val; -+ int ret; -+ -+ phy_modify_mmd(phydev, devad, regnum, -+ mask, cal_val); -+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_AD_CALIN, -+ MTK_PHY_DA_CALIN_FLAG); -+ -+ ret = phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_AD_CAL_CLK, reg_val, -+ reg_val & MTK_PHY_DA_CAL_CLK, 500, -+ ANALOG_INTERNAL_OPERATION_MAX_US, false); -+ if (ret) { -+ phydev_err(phydev, "Calibration cycle timeout\n"); -+ return ret; -+ } -+ -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_AD_CALIN, -+ MTK_PHY_DA_CALIN_FLAG); -+ ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_AD_CAL_COMP) >> -+ MTK_PHY_AD_CAL_COMP_OUT_SHIFT; -+ phydev_dbg(phydev, "cal_val: 0x%x, ret: %d\n", cal_val, ret); -+ -+ return ret; -+} -+ -+static int rext_fill_result(struct phy_device *phydev, u16 *buf) -+{ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG5, -+ MTK_PHY_RG_REXT_TRIM_MASK, buf[0] << 8); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_RG_BG_RASEL, -+ MTK_PHY_RG_BG_RASEL_MASK, buf[1]); -+ -+ return 0; -+} -+ -+static int rext_cal_efuse(struct phy_device *phydev, u32 *buf) -+{ -+ u16 rext_cal_val[2]; -+ -+ rext_cal_val[0] = EFS_RG_REXT_TRIM(buf[3]); -+ rext_cal_val[1] = EFS_RG_BG_RASEL(buf[3]); -+ rext_fill_result(phydev, rext_cal_val); -+ -+ return 0; -+} -+ -+static int tx_offset_fill_result(struct phy_device *phydev, u16 *buf) -+{ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_CR_TX_AMP_OFFSET_A_B, -+ MTK_PHY_CR_TX_AMP_OFFSET_A_MASK, buf[0] << 8); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_CR_TX_AMP_OFFSET_A_B, -+ MTK_PHY_CR_TX_AMP_OFFSET_B_MASK, buf[1]); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_CR_TX_AMP_OFFSET_C_D, -+ MTK_PHY_CR_TX_AMP_OFFSET_C_MASK, buf[2] << 8); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_CR_TX_AMP_OFFSET_C_D, -+ MTK_PHY_CR_TX_AMP_OFFSET_D_MASK, buf[3]); -+ -+ return 0; -+} -+ -+static int tx_offset_cal_efuse(struct phy_device *phydev, u32 *buf) -+{ -+ u16 tx_offset_cal_val[4]; -+ -+ tx_offset_cal_val[0] = EFS_DA_TX_AMP_OFFSET_A(buf[0]); -+ tx_offset_cal_val[1] = EFS_DA_TX_AMP_OFFSET_B(buf[1]); -+ tx_offset_cal_val[2] = EFS_DA_TX_AMP_OFFSET_C(buf[1]); -+ tx_offset_cal_val[3] = EFS_DA_TX_AMP_OFFSET_D(buf[1]); -+ -+ tx_offset_fill_result(phydev, tx_offset_cal_val); -+ -+ return 0; -+} -+ -+static int tx_amp_fill_result(struct phy_device *phydev, u16 *buf) -+{ -+ int i; -+ int bias[16] = {}; -+ const int vals_9461[16] = { 7, 1, 4, 7, -+ 7, 1, 4, 7, -+ 7, 1, 4, 7, -+ 7, 1, 4, 7 }; -+ const int vals_9481[16] = { 10, 6, 6, 10, -+ 10, 6, 6, 10, -+ 10, 6, 6, 10, -+ 10, 6, 6, 10 }; -+ switch (phydev->drv->phy_id) { -+ case MTK_GPHY_ID_MT7981: -+ /* We add some calibration to efuse values -+ * due to board level influence. -+ * GBE: +7, TBT: +1, HBT: +4, TST: +7 -+ */ -+ memcpy(bias, (const void *)vals_9461, sizeof(bias)); -+ break; -+ case MTK_GPHY_ID_MT7988: -+ memcpy(bias, (const void *)vals_9481, sizeof(bias)); -+ break; -+ } -+ -+ /* Prevent overflow */ -+ for (i = 0; i < 12; i++) { -+ if (buf[i >> 2] + bias[i] > 63) { -+ buf[i >> 2] = 63; -+ bias[i] = 0; -+ } -+ } -+ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TXVLD_DA_RG, -+ MTK_PHY_DA_TX_I2MPB_A_GBE_MASK, (buf[0] + bias[0]) << 10); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TXVLD_DA_RG, -+ MTK_PHY_DA_TX_I2MPB_A_TBT_MASK, buf[0] + bias[1]); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_A2, -+ MTK_PHY_DA_TX_I2MPB_A_HBT_MASK, (buf[0] + bias[2]) << 10); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_A2, -+ MTK_PHY_DA_TX_I2MPB_A_TST_MASK, buf[0] + bias[3]); -+ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B1, -+ MTK_PHY_DA_TX_I2MPB_B_GBE_MASK, (buf[1] + bias[4]) << 8); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B1, -+ MTK_PHY_DA_TX_I2MPB_B_TBT_MASK, buf[1] + bias[5]); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B2, -+ MTK_PHY_DA_TX_I2MPB_B_HBT_MASK, (buf[1] + bias[6]) << 8); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_B2, -+ MTK_PHY_DA_TX_I2MPB_B_TST_MASK, buf[1] + bias[7]); -+ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C1, -+ MTK_PHY_DA_TX_I2MPB_C_GBE_MASK, (buf[2] + bias[8]) << 8); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C1, -+ MTK_PHY_DA_TX_I2MPB_C_TBT_MASK, buf[2] + bias[9]); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C2, -+ MTK_PHY_DA_TX_I2MPB_C_HBT_MASK, (buf[2] + bias[10]) << 8); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_C2, -+ MTK_PHY_DA_TX_I2MPB_C_TST_MASK, buf[2] + bias[11]); -+ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D1, -+ MTK_PHY_DA_TX_I2MPB_D_GBE_MASK, (buf[3] + bias[12]) << 8); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D1, -+ MTK_PHY_DA_TX_I2MPB_D_TBT_MASK, buf[3] + bias[13]); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D2, -+ MTK_PHY_DA_TX_I2MPB_D_HBT_MASK, (buf[3] + bias[14]) << 8); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_TX_I2MPB_TEST_MODE_D2, -+ MTK_PHY_DA_TX_I2MPB_D_TST_MASK, buf[3] + bias[15]); -+ -+ return 0; -+} -+ -+static int tx_amp_cal_efuse(struct phy_device *phydev, u32 *buf) -+{ -+ u16 tx_amp_cal_val[4]; -+ -+ tx_amp_cal_val[0] = EFS_DA_TX_I2MPB_A(buf[0]); -+ tx_amp_cal_val[1] = EFS_DA_TX_I2MPB_B(buf[0]); -+ tx_amp_cal_val[2] = EFS_DA_TX_I2MPB_C(buf[0]); -+ tx_amp_cal_val[3] = EFS_DA_TX_I2MPB_D(buf[0]); -+ tx_amp_fill_result(phydev, tx_amp_cal_val); -+ -+ return 0; -+} -+ -+static int tx_r50_fill_result(struct phy_device *phydev, u16 tx_r50_cal_val, -+ u8 txg_calen_x) -+{ -+ int bias = 0; -+ u16 reg, val; -+ -+ if (phydev->drv->phy_id == MTK_GPHY_ID_MT7988) -+ bias = -2; -+ -+ val = clamp_val(bias + tx_r50_cal_val, 0, 63); -+ -+ switch (txg_calen_x) { -+ case PAIR_A: -+ reg = MTK_PHY_DA_TX_R50_PAIR_A; -+ break; -+ case PAIR_B: -+ reg = MTK_PHY_DA_TX_R50_PAIR_B; -+ break; -+ case PAIR_C: -+ reg = MTK_PHY_DA_TX_R50_PAIR_C; -+ break; -+ case PAIR_D: -+ reg = MTK_PHY_DA_TX_R50_PAIR_D; -+ break; -+ default: -+ return -EINVAL; -+ } -+ -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, reg, val | val << 8); -+ -+ return 0; -+} -+ -+static int tx_r50_cal_efuse(struct phy_device *phydev, u32 *buf, -+ u8 txg_calen_x) -+{ -+ u16 tx_r50_cal_val; -+ -+ switch (txg_calen_x) { -+ case PAIR_A: -+ tx_r50_cal_val = EFS_DA_TX_R50_A(buf[1]); -+ break; -+ case PAIR_B: -+ tx_r50_cal_val = EFS_DA_TX_R50_B(buf[1]); -+ break; -+ case PAIR_C: -+ tx_r50_cal_val = EFS_DA_TX_R50_C(buf[2]); -+ break; -+ case PAIR_D: -+ tx_r50_cal_val = EFS_DA_TX_R50_D(buf[2]); -+ break; -+ default: -+ return -EINVAL; -+ } -+ tx_r50_fill_result(phydev, tx_r50_cal_val, txg_calen_x); -+ -+ return 0; -+} -+ -+static int tx_vcm_cal_sw(struct phy_device *phydev, u8 rg_txreserve_x) -+{ -+ u8 lower_idx, upper_idx, txreserve_val; -+ u8 lower_ret, upper_ret; -+ int ret; -+ -+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG0, -+ MTK_PHY_RG_ANA_CALEN); -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG0, -+ MTK_PHY_RG_CAL_CKINV); -+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG1, -+ MTK_PHY_RG_TXVOS_CALEN); -+ -+ switch (rg_txreserve_x) { -+ case PAIR_A: -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_DASN_DAC_IN0_A, -+ MTK_PHY_DASN_DAC_IN0_A_MASK); -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_DASN_DAC_IN1_A, -+ MTK_PHY_DASN_DAC_IN1_A_MASK); -+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_ANA_CAL_RG0, -+ MTK_PHY_RG_ZCALEN_A); -+ break; -+ case PAIR_B: -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_DASN_DAC_IN0_B, -+ MTK_PHY_DASN_DAC_IN0_B_MASK); -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_DASN_DAC_IN1_B, -+ MTK_PHY_DASN_DAC_IN1_B_MASK); -+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_ANA_CAL_RG1, -+ MTK_PHY_RG_ZCALEN_B); -+ break; -+ case PAIR_C: -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_DASN_DAC_IN0_C, -+ MTK_PHY_DASN_DAC_IN0_C_MASK); -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_DASN_DAC_IN1_C, -+ MTK_PHY_DASN_DAC_IN1_C_MASK); -+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_ANA_CAL_RG1, -+ MTK_PHY_RG_ZCALEN_C); -+ break; -+ case PAIR_D: -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_DASN_DAC_IN0_D, -+ MTK_PHY_DASN_DAC_IN0_D_MASK); -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_DASN_DAC_IN1_D, -+ MTK_PHY_DASN_DAC_IN1_D_MASK); -+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_ANA_CAL_RG1, -+ MTK_PHY_RG_ZCALEN_D); -+ break; -+ default: -+ ret = -EINVAL; -+ goto restore; -+ } -+ -+ lower_idx = TXRESERVE_MIN; -+ upper_idx = TXRESERVE_MAX; -+ -+ phydev_dbg(phydev, "Start TX-VCM SW cal.\n"); -+ while ((upper_idx - lower_idx) > 1) { -+ txreserve_val = DIV_ROUND_CLOSEST(lower_idx + upper_idx, 2); -+ ret = cal_cycle(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG9, -+ MTK_PHY_DA_RX_PSBN_TBT_MASK | -+ MTK_PHY_DA_RX_PSBN_HBT_MASK | -+ MTK_PHY_DA_RX_PSBN_GBE_MASK | -+ MTK_PHY_DA_RX_PSBN_LP_MASK, -+ txreserve_val << 12 | txreserve_val << 8 | -+ txreserve_val << 4 | txreserve_val); -+ if (ret == 1) { -+ upper_idx = txreserve_val; -+ upper_ret = ret; -+ } else if (ret == 0) { -+ lower_idx = txreserve_val; -+ lower_ret = ret; -+ } else { -+ goto restore; -+ } -+ } -+ -+ if (lower_idx == TXRESERVE_MIN) { -+ lower_ret = cal_cycle(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RXADC_CTRL_RG9, -+ MTK_PHY_DA_RX_PSBN_TBT_MASK | -+ MTK_PHY_DA_RX_PSBN_HBT_MASK | -+ MTK_PHY_DA_RX_PSBN_GBE_MASK | -+ MTK_PHY_DA_RX_PSBN_LP_MASK, -+ lower_idx << 12 | lower_idx << 8 | -+ lower_idx << 4 | lower_idx); -+ ret = lower_ret; -+ } else if (upper_idx == TXRESERVE_MAX) { -+ upper_ret = cal_cycle(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RXADC_CTRL_RG9, -+ MTK_PHY_DA_RX_PSBN_TBT_MASK | -+ MTK_PHY_DA_RX_PSBN_HBT_MASK | -+ MTK_PHY_DA_RX_PSBN_GBE_MASK | -+ MTK_PHY_DA_RX_PSBN_LP_MASK, -+ upper_idx << 12 | upper_idx << 8 | -+ upper_idx << 4 | upper_idx); -+ ret = upper_ret; -+ } -+ if (ret < 0) -+ goto restore; -+ -+ /* We calibrate TX-VCM in different logic. Check upper index and then -+ * lower index. If this calibration is valid, apply lower index's result. -+ */ -+ ret = upper_ret - lower_ret; -+ if (ret == 1) { -+ ret = 0; -+ /* Make sure we use upper_idx in our calibration system */ -+ cal_cycle(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG9, -+ MTK_PHY_DA_RX_PSBN_TBT_MASK | -+ MTK_PHY_DA_RX_PSBN_HBT_MASK | -+ MTK_PHY_DA_RX_PSBN_GBE_MASK | -+ MTK_PHY_DA_RX_PSBN_LP_MASK, -+ upper_idx << 12 | upper_idx << 8 | -+ upper_idx << 4 | upper_idx); -+ phydev_dbg(phydev, "TX-VCM SW cal result: 0x%x\n", upper_idx); -+ } else if (lower_idx == TXRESERVE_MIN && upper_ret == 1 && -+ lower_ret == 1) { -+ ret = 0; -+ cal_cycle(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG9, -+ MTK_PHY_DA_RX_PSBN_TBT_MASK | -+ MTK_PHY_DA_RX_PSBN_HBT_MASK | -+ MTK_PHY_DA_RX_PSBN_GBE_MASK | -+ MTK_PHY_DA_RX_PSBN_LP_MASK, -+ lower_idx << 12 | lower_idx << 8 | -+ lower_idx << 4 | lower_idx); -+ phydev_warn(phydev, "TX-VCM SW cal result at low margin 0x%x\n", -+ lower_idx); -+ } else if (upper_idx == TXRESERVE_MAX && upper_ret == 0 && -+ lower_ret == 0) { -+ ret = 0; -+ phydev_warn(phydev, "TX-VCM SW cal result at high margin 0x%x\n", -+ upper_idx); -+ } else { -+ ret = -EINVAL; -+ } -+ -+restore: -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG0, -+ MTK_PHY_RG_ANA_CALEN); -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG1, -+ MTK_PHY_RG_TXVOS_CALEN); -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG0, -+ MTK_PHY_RG_ZCALEN_A); -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_ANA_CAL_RG1, -+ MTK_PHY_RG_ZCALEN_B | MTK_PHY_RG_ZCALEN_C | -+ MTK_PHY_RG_ZCALEN_D); -+ -+ return ret; -+} -+ -+static void mt798x_phy_common_finetune(struct phy_device *phydev) -+{ -+ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); -+ /* EnabRandUpdTrig = 1 */ -+ __phy_write(phydev, 0x11, 0x2f00); -+ __phy_write(phydev, 0x12, 0xe); -+ __phy_write(phydev, 0x10, 0x8fb0); -+ -+ /* NormMseLoThresh = 85 */ -+ __phy_write(phydev, 0x11, 0x55a0); -+ __phy_write(phydev, 0x12, 0x0); -+ __phy_write(phydev, 0x10, 0x83aa); -+ -+ /* TrFreeze = 0 */ -+ __phy_write(phydev, 0x11, 0x0); -+ __phy_write(phydev, 0x12, 0x0); -+ __phy_write(phydev, 0x10, 0x9686); -+ -+ /* SSTrKp1000Slv = 5 */ -+ __phy_write(phydev, 0x11, 0xbaef); -+ __phy_write(phydev, 0x12, 0x2e); -+ __phy_write(phydev, 0x10, 0x968c); -+ -+ /* MrvlTrFix100Kp = 3, MrvlTrFix100Kf = 2, -+ * MrvlTrFix1000Kp = 3, MrvlTrFix1000Kf = 2 -+ */ -+ __phy_write(phydev, 0x11, 0xd10a); -+ __phy_write(phydev, 0x12, 0x34); -+ __phy_write(phydev, 0x10, 0x8f82); -+ -+ /* VcoSlicerThreshBitsHigh */ -+ __phy_write(phydev, 0x11, 0x5555); -+ __phy_write(phydev, 0x12, 0x55); -+ __phy_write(phydev, 0x10, 0x8ec0); -+ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); -+ -+ /* TR_OPEN_LOOP_EN = 1, lpf_x_average = 9*/ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG234, -+ MTK_PHY_TR_OPEN_LOOP_EN_MASK | MTK_PHY_LPF_X_AVERAGE_MASK, -+ BIT(0) | FIELD_PREP(MTK_PHY_LPF_X_AVERAGE_MASK, 0x9)); -+ -+ /* rg_tr_lpf_cnt_val = 512 */ -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LPF_CNT_VAL, 0x200); -+ -+ /* IIR2 related */ -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K1_L, 0x82); -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K1_U, 0x0); -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K2_L, 0x103); -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K2_U, 0x0); -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K3_L, 0x82); -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K3_U, 0x0); -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K4_L, 0xd177); -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K4_U, 0x3); -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K5_L, 0x2c82); -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LP_IIR2_K5_U, 0xe); -+ -+ /* FFE peaking */ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG27C, -+ MTK_PHY_VGASTATE_FFE_THR_ST1_MASK, 0x1b << 8); -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG27D, -+ MTK_PHY_VGASTATE_FFE_THR_ST2_MASK, 0x1e); -+ -+ /* Disable LDO pump */ -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LDO_PUMP_EN_PAIRAB, 0x0); -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LDO_PUMP_EN_PAIRCD, 0x0); -+ /* Adjust LDO output voltage */ -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LDO_OUTPUT_V, 0x2222); -+} -+ -+static void mt7981_phy_finetune(struct phy_device *phydev) -+{ -+ u16 val[8] = { 0x01ce, 0x01c1, -+ 0x020f, 0x0202, -+ 0x03d0, 0x03c0, -+ 0x0013, 0x0005 }; -+ int i, k; -+ -+ /* 100M eye finetune: -+ * Keep middle level of TX MLT3 shapper as default. -+ * Only change TX MLT3 overshoot level here. -+ */ -+ for (k = 0, i = 1; i < 12; i++) { -+ if (i % 3 == 0) -+ continue; -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, i, val[k++]); -+ } -+ -+ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); -+ /* SlvDSPreadyTime = 24, MasDSPreadyTime = 24 */ -+ __phy_write(phydev, 0x11, 0xc71); -+ __phy_write(phydev, 0x12, 0xc); -+ __phy_write(phydev, 0x10, 0x8fae); -+ -+ /* ResetSyncOffset = 6 */ -+ __phy_write(phydev, 0x11, 0x600); -+ __phy_write(phydev, 0x12, 0x0); -+ __phy_write(phydev, 0x10, 0x8fc0); -+ -+ /* VgaDecRate = 1 */ -+ __phy_write(phydev, 0x11, 0x4c2a); -+ __phy_write(phydev, 0x12, 0x3e); -+ __phy_write(phydev, 0x10, 0x8fa4); -+ -+ /* FfeUpdGainForce = 4 */ -+ __phy_write(phydev, 0x11, 0x240); -+ __phy_write(phydev, 0x12, 0x0); -+ __phy_write(phydev, 0x10, 0x9680); -+ -+ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); -+} -+ -+static void mt7988_phy_finetune(struct phy_device *phydev) -+{ -+ u16 val[12] = { 0x0187, 0x01cd, 0x01c8, 0x0182, -+ 0x020d, 0x0206, 0x0384, 0x03d0, -+ 0x03c6, 0x030a, 0x0011, 0x0005 }; -+ int i; -+ -+ /* Set default MLT3 shaper first */ -+ for (i = 0; i < 12; i++) -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, i, val[i]); -+ -+ /* TCT finetune */ -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_TX_FILTER, 0x5); -+ -+ /* Disable TX power saving */ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG7, -+ MTK_PHY_DA_AD_BUF_BIAS_LP_MASK, 0x3 << 8); -+ -+ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); -+ -+ /* SlvDSPreadyTime = 24, MasDSPreadyTime = 12 */ -+ __phy_write(phydev, 0x11, 0x671); -+ __phy_write(phydev, 0x12, 0xc); -+ __phy_write(phydev, 0x10, 0x8fae); -+ -+ /* ResetSyncOffset = 5 */ -+ __phy_write(phydev, 0x11, 0x500); -+ __phy_write(phydev, 0x12, 0x0); -+ __phy_write(phydev, 0x10, 0x8fc0); -+ -+ /* VgaDecRate is 1 at default on mt7988 */ -+ -+ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); -+ -+ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_2A30); -+ /* TxClkOffset = 2 */ -+ __phy_modify(phydev, MTK_PHY_ANARG_RG, MTK_PHY_TCLKOFFSET_MASK, -+ FIELD_PREP(MTK_PHY_TCLKOFFSET_MASK, 0x2)); -+ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); -+} -+ -+static void mt798x_phy_eee(struct phy_device *phydev) -+{ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG120, -+ MTK_PHY_LPI_SIG_EN_LO_THRESH1000_MASK | -+ MTK_PHY_LPI_SIG_EN_HI_THRESH1000_MASK, -+ FIELD_PREP(MTK_PHY_LPI_SIG_EN_LO_THRESH1000_MASK, 0x0) | -+ FIELD_PREP(MTK_PHY_LPI_SIG_EN_HI_THRESH1000_MASK, 0x14)); -+ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG122, -+ MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK, -+ FIELD_PREP(MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK, -+ 0xff)); -+ -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_TESTMUX_ADC_CTRL, -+ MTK_PHY_RG_TXEN_DIG_MASK); -+ -+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_DEV1E_REG19b, MTK_PHY_BYPASS_DSP_LPI_READY); -+ -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_DEV1E_REG234, MTK_PHY_TR_LP_IIR_EEE_EN); -+ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG238, -+ MTK_PHY_LPI_SLV_SEND_TX_TIMER_MASK | -+ MTK_PHY_LPI_SLV_SEND_TX_EN, -+ FIELD_PREP(MTK_PHY_LPI_SLV_SEND_TX_TIMER_MASK, 0x120)); -+ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG239, -+ MTK_PHY_LPI_SEND_LOC_TIMER_MASK | -+ MTK_PHY_LPI_TXPCS_LOC_RCV, -+ FIELD_PREP(MTK_PHY_LPI_SEND_LOC_TIMER_MASK, 0x117)); -+ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG2C7, -+ MTK_PHY_MAX_GAIN_MASK | MTK_PHY_MIN_GAIN_MASK, -+ FIELD_PREP(MTK_PHY_MAX_GAIN_MASK, 0x8) | -+ FIELD_PREP(MTK_PHY_MIN_GAIN_MASK, 0x13)); -+ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG2D1, -+ MTK_PHY_VCO_SLICER_THRESH_BITS_HIGH_EEE_MASK, -+ FIELD_PREP(MTK_PHY_VCO_SLICER_THRESH_BITS_HIGH_EEE_MASK, -+ 0x33) | -+ MTK_PHY_LPI_SKIP_SD_SLV_TR | MTK_PHY_LPI_TR_READY | -+ MTK_PHY_LPI_VCO_EEE_STG0_EN); -+ -+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG323, -+ MTK_PHY_EEE_WAKE_MAS_INT_DC | -+ MTK_PHY_EEE_WAKE_SLV_INT_DC); -+ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG324, -+ MTK_PHY_SMI_DETCNT_MAX_MASK, -+ FIELD_PREP(MTK_PHY_SMI_DETCNT_MAX_MASK, 0x3f) | -+ MTK_PHY_SMI_DET_MAX_EN); -+ -+ phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG326, -+ MTK_PHY_LPI_MODE_SD_ON | MTK_PHY_RESET_RANDUPD_CNT | -+ MTK_PHY_TREC_UPDATE_ENAB_CLR | -+ MTK_PHY_LPI_QUIT_WAIT_DFE_SIG_DET_OFF | -+ MTK_PHY_TR_READY_SKIP_AFE_WAKEUP); -+ -+ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); -+ /* Regsigdet_sel_1000 = 0 */ -+ __phy_write(phydev, 0x11, 0xb); -+ __phy_write(phydev, 0x12, 0x0); -+ __phy_write(phydev, 0x10, 0x9690); -+ -+ /* REG_EEE_st2TrKf1000 = 3 */ -+ __phy_write(phydev, 0x11, 0x114f); -+ __phy_write(phydev, 0x12, 0x2); -+ __phy_write(phydev, 0x10, 0x969a); -+ -+ /* RegEEE_slv_wake_tr_timer_tar = 6, RegEEE_slv_remtx_timer_tar = 20 */ -+ __phy_write(phydev, 0x11, 0x3028); -+ __phy_write(phydev, 0x12, 0x0); -+ __phy_write(phydev, 0x10, 0x969e); -+ -+ /* RegEEE_slv_wake_int_timer_tar = 8 */ -+ __phy_write(phydev, 0x11, 0x5010); -+ __phy_write(phydev, 0x12, 0x0); -+ __phy_write(phydev, 0x10, 0x96a0); -+ -+ /* RegEEE_trfreeze_timer2 = 586 */ -+ __phy_write(phydev, 0x11, 0x24a); -+ __phy_write(phydev, 0x12, 0x0); -+ __phy_write(phydev, 0x10, 0x96a8); -+ -+ /* RegEEE100Stg1_tar = 16 */ -+ __phy_write(phydev, 0x11, 0x3210); -+ __phy_write(phydev, 0x12, 0x0); -+ __phy_write(phydev, 0x10, 0x96b8); -+ -+ /* REGEEE_wake_slv_tr_wait_dfesigdet_en = 1 */ -+ __phy_write(phydev, 0x11, 0x1463); -+ __phy_write(phydev, 0x12, 0x0); -+ __phy_write(phydev, 0x10, 0x96ca); -+ -+ /* DfeTailEnableVgaThresh1000 = 27 */ -+ __phy_write(phydev, 0x11, 0x36); -+ __phy_write(phydev, 0x12, 0x0); -+ __phy_write(phydev, 0x10, 0x8f80); -+ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); -+ -+ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_3); -+ __phy_modify(phydev, MTK_PHY_LPI_REG_14, MTK_PHY_LPI_WAKE_TIMER_1000_MASK, -+ FIELD_PREP(MTK_PHY_LPI_WAKE_TIMER_1000_MASK, 0x19c)); -+ -+ __phy_modify(phydev, MTK_PHY_LPI_REG_1c, MTK_PHY_SMI_DET_ON_THRESH_MASK, -+ FIELD_PREP(MTK_PHY_SMI_DET_ON_THRESH_MASK, 0xc)); -+ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); -+ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, -+ MTK_PHY_RG_LPI_PCS_DSP_CTRL_REG122, -+ MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK, -+ FIELD_PREP(MTK_PHY_LPI_NORM_MSE_HI_THRESH1000_MASK, 0xff)); -+} -+ -+static int cal_sw(struct phy_device *phydev, enum CAL_ITEM cal_item, -+ u8 start_pair, u8 end_pair) -+{ -+ u8 pair_n; -+ int ret; -+ -+ for (pair_n = start_pair; pair_n <= end_pair; pair_n++) { -+ /* TX_OFFSET & TX_AMP have no SW calibration. */ -+ switch (cal_item) { -+ case TX_VCM: -+ ret = tx_vcm_cal_sw(phydev, pair_n); -+ break; -+ default: -+ return -EINVAL; -+ } -+ if (ret) -+ return ret; -+ } -+ return 0; -+} -+ -+static int cal_efuse(struct phy_device *phydev, enum CAL_ITEM cal_item, -+ u8 start_pair, u8 end_pair, u32 *buf) -+{ -+ u8 pair_n; -+ int ret; -+ -+ for (pair_n = start_pair; pair_n <= end_pair; pair_n++) { -+ /* TX_VCM has no efuse calibration. */ -+ switch (cal_item) { -+ case REXT: -+ ret = rext_cal_efuse(phydev, buf); -+ break; -+ case TX_OFFSET: -+ ret = tx_offset_cal_efuse(phydev, buf); -+ break; -+ case TX_AMP: -+ ret = tx_amp_cal_efuse(phydev, buf); -+ break; -+ case TX_R50: -+ ret = tx_r50_cal_efuse(phydev, buf, pair_n); -+ break; -+ default: -+ return -EINVAL; -+ } -+ if (ret) -+ return ret; -+ } -+ -+ return 0; -+} -+ -+static int start_cal(struct phy_device *phydev, enum CAL_ITEM cal_item, -+ enum CAL_MODE cal_mode, u8 start_pair, -+ u8 end_pair, u32 *buf) -+{ -+ int ret; -+ -+ switch (cal_mode) { -+ case EFUSE_M: -+ ret = cal_efuse(phydev, cal_item, start_pair, -+ end_pair, buf); -+ break; -+ case SW_M: -+ ret = cal_sw(phydev, cal_item, start_pair, end_pair); -+ break; -+ default: -+ return -EINVAL; -+ } -+ -+ if (ret) { -+ phydev_err(phydev, "cal %d failed\n", cal_item); -+ return -EIO; -+ } -+ -+ return 0; -+} -+ -+static int mt798x_phy_calibration(struct phy_device *phydev) -+{ -+ int ret = 0; -+ u32 *buf; -+ size_t len; -+ struct nvmem_cell *cell; -+ -+ cell = nvmem_cell_get(&phydev->mdio.dev, "phy-cal-data"); -+ if (IS_ERR(cell)) { -+ if (PTR_ERR(cell) == -EPROBE_DEFER) -+ return PTR_ERR(cell); -+ return 0; -+ } -+ -+ buf = (u32 *)nvmem_cell_read(cell, &len); -+ if (IS_ERR(buf)) -+ return PTR_ERR(buf); -+ nvmem_cell_put(cell); -+ -+ if (!buf[0] || !buf[1] || !buf[2] || !buf[3] || len < 4 * sizeof(u32)) { -+ phydev_err(phydev, "invalid efuse data\n"); -+ ret = -EINVAL; -+ goto out; -+ } -+ -+ ret = start_cal(phydev, REXT, EFUSE_M, NO_PAIR, NO_PAIR, buf); -+ if (ret) -+ goto out; -+ ret = start_cal(phydev, TX_OFFSET, EFUSE_M, NO_PAIR, NO_PAIR, buf); -+ if (ret) -+ goto out; -+ ret = start_cal(phydev, TX_AMP, EFUSE_M, NO_PAIR, NO_PAIR, buf); -+ if (ret) -+ goto out; -+ ret = start_cal(phydev, TX_R50, EFUSE_M, PAIR_A, PAIR_D, buf); -+ if (ret) -+ goto out; -+ ret = start_cal(phydev, TX_VCM, SW_M, PAIR_A, PAIR_A, buf); -+ if (ret) -+ goto out; -+ -+out: -+ kfree(buf); -+ return ret; -+} -+ -+static int mt798x_phy_config_init(struct phy_device *phydev) -+{ -+ switch (phydev->drv->phy_id) { -+ case MTK_GPHY_ID_MT7981: -+ mt7981_phy_finetune(phydev); -+ break; -+ case MTK_GPHY_ID_MT7988: -+ mt7988_phy_finetune(phydev); -+ break; -+ } -+ -+ mt798x_phy_common_finetune(phydev); -+ mt798x_phy_eee(phydev); -+ -+ return mt798x_phy_calibration(phydev); -+} -+ -+static struct phy_driver mtk_socphy_driver[] = { -+ { -+ PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7981), -+ .name = "MediaTek MT7981 PHY", -+ .config_init = mt798x_phy_config_init, -+ .config_intr = genphy_no_config_intr, -+ .handle_interrupt = genphy_handle_interrupt_no_ack, -+ .probe = mt798x_phy_calibration, -+ .suspend = genphy_suspend, -+ .resume = genphy_resume, -+ .read_page = mtk_socphy_read_page, -+ .write_page = mtk_socphy_write_page, -+ }, -+ { -+ PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7988), -+ .name = "MediaTek MT7988 PHY", -+ .config_init = mt798x_phy_config_init, -+ .config_intr = genphy_no_config_intr, -+ .handle_interrupt = genphy_handle_interrupt_no_ack, -+ .probe = mt798x_phy_calibration, -+ .suspend = genphy_suspend, -+ .resume = genphy_resume, -+ .read_page = mtk_socphy_read_page, -+ .write_page = mtk_socphy_write_page, -+ }, -+}; -+ -+module_phy_driver(mtk_socphy_driver); -+ -+static struct mdio_device_id __maybe_unused mtk_socphy_tbl[] = { -+ { PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7981) }, -+ { PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7988) }, -+ { } -+}; -+ -+MODULE_DESCRIPTION("MediaTek SoC Gigabit Ethernet PHY driver"); -+MODULE_AUTHOR("Daniel Golle "); -+MODULE_AUTHOR("SkyLake Huang "); -+MODULE_LICENSE("GPL"); -+ -+MODULE_DEVICE_TABLE(mdio, mtk_socphy_tbl); ---- a/drivers/net/phy/mediatek-ge.c -+++ b/drivers/net/phy/mediatek-ge.c -@@ -136,7 +136,8 @@ static struct phy_driver mtk_gephy_drive - module_phy_driver(mtk_gephy_driver); - - static struct mdio_device_id __maybe_unused mtk_gephy_tbl[] = { -- { PHY_ID_MATCH_VENDOR(0x03a29400) }, -+ { PHY_ID_MATCH_EXACT(0x03a29441) }, -+ { PHY_ID_MATCH_EXACT(0x03a29412) }, - { } - }; - diff --git a/target/linux/mediatek/patches-5.15/731-net-phy-mediatek-ge-soc-initialize-MT7988-PHY-LEDs-d.patch b/target/linux/mediatek/patches-5.15/731-net-phy-mediatek-ge-soc-initialize-MT7988-PHY-LEDs-d.patch deleted file mode 100644 index 83d0f26bf4..0000000000 --- a/target/linux/mediatek/patches-5.15/731-net-phy-mediatek-ge-soc-initialize-MT7988-PHY-LEDs-d.patch +++ /dev/null @@ -1,213 +0,0 @@ -From 5d2d78860f98eb5c03bc404eb024606878901ac8 Mon Sep 17 00:00:00 2001 -From: Daniel Golle -Date: Tue, 13 Jun 2023 03:27:14 +0100 -Subject: [PATCH] net: phy: mediatek-ge-soc: initialize MT7988 PHY LEDs default - state - -Initialize LEDs and set sane default values. -Read boottrap register and apply LED polarities accordingly to get -uniform behavior from all LEDs on MT7988. -Requires syscon phandle 'mediatek,pio' present in parenting MDIO bus -which should point to the syscon holding the boottrap register. - -Signed-off-by: Daniel Golle ---- - drivers/net/phy/mediatek-ge-soc.c | 144 ++++++++++++++++++++++++++++-- - 1 file changed, 136 insertions(+), 8 deletions(-) - ---- a/drivers/net/phy/mediatek-ge-soc.c -+++ b/drivers/net/phy/mediatek-ge-soc.c -@@ -1,11 +1,13 @@ - // SPDX-License-Identifier: GPL-2.0+ - #include -+#include - #include - #include - #include - #include - #include - #include -+#include - - #define MTK_GPHY_ID_MT7981 0x03a29461 - #define MTK_GPHY_ID_MT7988 0x03a29481 -@@ -208,9 +210,40 @@ - #define MTK_PHY_DA_TX_R50_PAIR_C 0x53f - #define MTK_PHY_DA_TX_R50_PAIR_D 0x540 - -+/* Registers on MDIO_MMD_VEND2 */ -+#define MTK_PHY_LED0_ON_CTRL 0x24 -+#define MTK_PHY_LED1_ON_CTRL 0x26 -+#define MTK_PHY_LED_ON_MASK GENMASK(6, 0) -+#define MTK_PHY_LED_ON_LINK1000 BIT(0) -+#define MTK_PHY_LED_ON_LINK100 BIT(1) -+#define MTK_PHY_LED_ON_LINK10 BIT(2) -+#define MTK_PHY_LED_ON_LINKDOWN BIT(3) -+#define MTK_PHY_LED_ON_FDX BIT(4) /* Full duplex */ -+#define MTK_PHY_LED_ON_HDX BIT(5) /* Half duplex */ -+#define MTK_PHY_LED_FORCE_ON BIT(6) -+#define MTK_PHY_LED_POLARITY BIT(14) -+#define MTK_PHY_LED_ENABLE BIT(15) -+ -+#define MTK_PHY_LED0_BLINK_CTRL 0x25 -+#define MTK_PHY_LED1_BLINK_CTRL 0x27 -+#define MTK_PHY_LED_1000TX BIT(0) -+#define MTK_PHY_LED_1000RX BIT(1) -+#define MTK_PHY_LED_100TX BIT(2) -+#define MTK_PHY_LED_100RX BIT(3) -+#define MTK_PHY_LED_10TX BIT(4) -+#define MTK_PHY_LED_10RX BIT(5) -+#define MTK_PHY_LED_COLLISION BIT(6) -+#define MTK_PHY_LED_RX_CRC_ERR BIT(7) -+#define MTK_PHY_LED_RX_IDLE_ERR BIT(8) -+#define MTK_PHY_LED_FORCE_BLINK BIT(9) -+ - #define MTK_PHY_RG_BG_RASEL 0x115 - #define MTK_PHY_RG_BG_RASEL_MASK GENMASK(2, 0) - -+/* Register in boottrap syscon defining the initial state of the 4 PHY LEDs */ -+#define RG_GPIO_MISC_TPBANK0 0x6f0 -+#define RG_GPIO_MISC_TPBANK0_BOOTMODE GENMASK(11, 8) -+ - /* These macro privides efuse parsing for internal phy. */ - #define EFS_DA_TX_I2MPB_A(x) (((x) >> 0) & GENMASK(5, 0)) - #define EFS_DA_TX_I2MPB_B(x) (((x) >> 6) & GENMASK(5, 0)) -@@ -238,13 +271,6 @@ enum { - PAIR_D, - }; - --enum { -- GPHY_PORT0, -- GPHY_PORT1, -- GPHY_PORT2, -- GPHY_PORT3, --}; -- - enum calibration_mode { - EFUSE_K, - SW_K -@@ -263,6 +289,10 @@ enum CAL_MODE { - SW_M - }; - -+struct mtk_socphy_shared { -+ u32 boottrap; -+}; -+ - static int mtk_socphy_read_page(struct phy_device *phydev) - { - return __phy_read(phydev, MTK_EXT_PAGE_ACCESS); -@@ -1073,6 +1103,104 @@ static int mt798x_phy_config_init(struct - return mt798x_phy_calibration(phydev); - } - -+static int mt798x_phy_setup_led(struct phy_device *phydev, bool inverted) -+{ -+ struct pinctrl *pinctrl; -+ const u16 led_on_ctrl_defaults = MTK_PHY_LED_ENABLE | -+ MTK_PHY_LED_ON_LINK1000 | -+ MTK_PHY_LED_ON_LINK100 | -+ MTK_PHY_LED_ON_LINK10; -+ const u16 led_blink_defaults = MTK_PHY_LED_1000TX | -+ MTK_PHY_LED_1000RX | -+ MTK_PHY_LED_100TX | -+ MTK_PHY_LED_100RX | -+ MTK_PHY_LED_10TX | -+ MTK_PHY_LED_10RX; -+ -+ phy_write_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED0_ON_CTRL, -+ led_on_ctrl_defaults ^ -+ (inverted ? MTK_PHY_LED_POLARITY : 0)); -+ -+ phy_write_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED1_ON_CTRL, -+ led_on_ctrl_defaults); -+ -+ phy_write_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED0_BLINK_CTRL, -+ led_blink_defaults); -+ -+ phy_write_mmd(phydev, MDIO_MMD_VEND2, MTK_PHY_LED1_BLINK_CTRL, -+ led_blink_defaults); -+ -+ pinctrl = devm_pinctrl_get_select(&phydev->mdio.dev, "gbe-led"); -+ if (IS_ERR(pinctrl)) -+ dev_err(&phydev->mdio.bus->dev, "Failed to setup PHY LED\n"); -+ -+ return 0; -+} -+ -+static int mt7988_phy_probe_shared(struct phy_device *phydev) -+{ -+ struct device_node *np = dev_of_node(&phydev->mdio.bus->dev); -+ struct mtk_socphy_shared *priv = phydev->shared->priv; -+ struct regmap *regmap; -+ u32 reg; -+ int ret; -+ -+ /* The LED0 of the 4 PHYs in MT7988 are wired to SoC pins LED_A, LED_B, -+ * LED_C and LED_D respectively. At the same time those pins are used to -+ * bootstrap configuration of the reference clock source (LED_A), -+ * DRAM DDRx16b x2/x1 (LED_B) and boot device (LED_C, LED_D). -+ * In practise this is done using a LED and a resistor pulling the pin -+ * either to GND or to VIO. -+ * The detected value at boot time is accessible at run-time using the -+ * TPBANK0 register located in the gpio base of the pinctrl, in order -+ * to read it here it needs to be referenced by a phandle called -+ * 'mediatek,pio' in the MDIO bus hosting the PHY. -+ * The 4 bits in TPBANK0 are kept as package shared data and are used to -+ * set LED polarity for each of the LED0. -+ */ -+ regmap = syscon_regmap_lookup_by_phandle(np, "mediatek,pio"); -+ if (IS_ERR(regmap)) -+ return PTR_ERR(regmap); -+ -+ ret = regmap_read(regmap, RG_GPIO_MISC_TPBANK0, ®); -+ if (ret) -+ return ret; -+ -+ priv->boottrap = FIELD_GET(RG_GPIO_MISC_TPBANK0_BOOTMODE, reg); -+ -+ return 0; -+} -+ -+static bool mt7988_phy_get_boottrap_polarity(struct phy_device *phydev) -+{ -+ struct mtk_socphy_shared *priv = phydev->shared->priv; -+ -+ if (priv->boottrap & BIT(phydev->mdio.addr)) -+ return false; -+ -+ return true; -+} -+ -+static int mt7988_phy_probe(struct phy_device *phydev) -+{ -+ int err; -+ -+ err = devm_phy_package_join(&phydev->mdio.dev, phydev, 0, -+ sizeof(struct mtk_socphy_shared)); -+ if (err) -+ return err; -+ -+ if (phy_package_probe_once(phydev)) { -+ err = mt7988_phy_probe_shared(phydev); -+ if (err) -+ return err; -+ } -+ -+ mt798x_phy_setup_led(phydev, mt7988_phy_get_boottrap_polarity(phydev)); -+ -+ return mt798x_phy_calibration(phydev); -+} -+ - static struct phy_driver mtk_socphy_driver[] = { - { - PHY_ID_MATCH_EXACT(MTK_GPHY_ID_MT7981), -@@ -1092,7 +1220,7 @@ static struct phy_driver mtk_socphy_driv - .config_init = mt798x_phy_config_init, - .config_intr = genphy_no_config_intr, - .handle_interrupt = genphy_handle_interrupt_no_ack, -- .probe = mt798x_phy_calibration, -+ .probe = mt7988_phy_probe, - .suspend = genphy_suspend, - .resume = genphy_resume, - .read_page = mtk_socphy_read_page, diff --git a/target/linux/mediatek/patches-5.15/732-net-phy-mxl-gpy-don-t-use-SGMII-AN-if-using-phylink.patch b/target/linux/mediatek/patches-5.15/732-net-phy-mxl-gpy-don-t-use-SGMII-AN-if-using-phylink.patch deleted file mode 100644 index 6df4436ab9..0000000000 --- a/target/linux/mediatek/patches-5.15/732-net-phy-mxl-gpy-don-t-use-SGMII-AN-if-using-phylink.patch +++ /dev/null @@ -1,63 +0,0 @@ -From a969b663c866129ed9eb217785a6574fbe826f1d Mon Sep 17 00:00:00 2001 -From: Daniel Golle -Date: Thu, 6 Apr 2023 23:36:50 +0100 -Subject: [PATCH] net: phy: mxl-gpy: don't use SGMII AN if using phylink - -MAC drivers using phylink expect SGMII in-band-status to be switched off -when attached to a PHY. Make sure this is the case also for mxl-gpy which -keeps SGMII in-band-status in case of SGMII interface mode is used. - -Signed-off-by: Daniel Golle ---- - drivers/net/phy/mxl-gpy.c | 19 ++++++++++++++++--- - 1 file changed, 16 insertions(+), 3 deletions(-) - ---- a/drivers/net/phy/mxl-gpy.c -+++ b/drivers/net/phy/mxl-gpy.c -@@ -195,8 +195,11 @@ static bool gpy_2500basex_chk(struct phy - - phydev->speed = SPEED_2500; - phydev->interface = PHY_INTERFACE_MODE_2500BASEX; -- phy_modify_mmd(phydev, MDIO_MMD_VEND1, VSPEC1_SGMII_CTRL, -- VSPEC1_SGMII_CTRL_ANEN, 0); -+ -+ if (!phydev->phylink) -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, VSPEC1_SGMII_CTRL, -+ VSPEC1_SGMII_CTRL_ANEN, 0); -+ - return true; - } - -@@ -220,6 +223,14 @@ static int gpy_config_aneg(struct phy_de - u32 adv; - int ret; - -+ /* Disable SGMII auto-negotiation if using phylink */ -+ if (phydev->phylink) { -+ ret = phy_modify_mmd(phydev, MDIO_MMD_VEND1, VSPEC1_SGMII_CTRL, -+ VSPEC1_SGMII_CTRL_ANEN, 0); -+ if (ret < 0) -+ return ret; -+ } -+ - if (phydev->autoneg == AUTONEG_DISABLE) { - /* Configure half duplex with genphy_setup_forced, - * because genphy_c45_pma_setup_forced does not support. -@@ -310,6 +321,8 @@ static void gpy_update_interface(struct - switch (phydev->speed) { - case SPEED_2500: - phydev->interface = PHY_INTERFACE_MODE_2500BASEX; -+ if (phydev->phylink) -+ break; - ret = phy_modify_mmd(phydev, MDIO_MMD_VEND1, VSPEC1_SGMII_CTRL, - VSPEC1_SGMII_CTRL_ANEN, 0); - if (ret < 0) -@@ -321,7 +334,7 @@ static void gpy_update_interface(struct - case SPEED_100: - case SPEED_10: - phydev->interface = PHY_INTERFACE_MODE_SGMII; -- if (gpy_sgmii_aneg_en(phydev)) -+ if (phydev->phylink || gpy_sgmii_aneg_en(phydev)) - break; - /* Enable and restart SGMII ANEG for 10/100/1000Mbps link speed - * if ANEG is disabled (in 2500-BaseX mode). diff --git a/target/linux/mediatek/patches-5.15/733-net-phy-add-driver-for-MediaTek-2.5G-PHY.patch b/target/linux/mediatek/patches-5.15/733-net-phy-add-driver-for-MediaTek-2.5G-PHY.patch deleted file mode 100644 index 7600819246..0000000000 --- a/target/linux/mediatek/patches-5.15/733-net-phy-add-driver-for-MediaTek-2.5G-PHY.patch +++ /dev/null @@ -1,39 +0,0 @@ -From 128dc09b0af36772062142ce9e85b19c84ac789a Mon Sep 17 00:00:00 2001 -From: Daniel Golle -Date: Tue, 28 Feb 2023 17:53:37 +0000 -Subject: [PATCH] net: phy: add driver for MediaTek 2.5G PHY - -Signed-off-by: Daniel Golle ---- - drivers/net/phy/Kconfig | 7 ++ - drivers/net/phy/Makefile | 1 + - drivers/net/phy/mediatek-2p5ge.c | 220 +++++++++++++++++++++++++++++++ - 3 files changed, 226 insertions(+) - create mode 100644 drivers/net/phy/mediatek-2p5ge.c - ---- a/drivers/net/phy/Kconfig -+++ b/drivers/net/phy/Kconfig -@@ -302,6 +302,13 @@ config MEDIATEK_GE_SOC_PHY - present in the SoCs efuse and will dynamically calibrate VCM - (common-mode voltage) during startup. - -+config MEDIATEK_2P5G_PHY -+ tristate "MediaTek 2.5G Ethernet PHY" -+ depends on (ARCH_MEDIATEK && ARM64) || COMPILE_TEST -+ default NET_MEDIATEK_SOC -+ help -+ Supports the MediaTek 2.5G Ethernet PHY. -+ - config MICREL_PHY - tristate "Micrel PHYs" - help ---- a/drivers/net/phy/Makefile -+++ b/drivers/net/phy/Makefile -@@ -76,6 +76,7 @@ obj-$(CONFIG_MARVELL_10G_PHY) += marvell - obj-$(CONFIG_MARVELL_PHY) += marvell.o - obj-$(CONFIG_MARVELL_88X2222_PHY) += marvell-88x2222.o - obj-$(CONFIG_MAXLINEAR_GPHY) += mxl-gpy.o -+obj-$(CONFIG_MEDIATEK_2P5G_PHY) += mediatek-2p5ge.o - obj-$(CONFIG_MEDIATEK_GE_PHY) += mediatek-ge.o - obj-$(CONFIG_MEDIATEK_GE_SOC_PHY) += mediatek-ge-soc.o - obj-$(CONFIG_MESON_GXL_PHY) += meson-gxl.o diff --git a/target/linux/mediatek/patches-5.15/734-net-phy-mediatek-ge-soc-sync-driver-with-MediaTek-SD.patch b/target/linux/mediatek/patches-5.15/734-net-phy-mediatek-ge-soc-sync-driver-with-MediaTek-SD.patch deleted file mode 100644 index f983be4e44..0000000000 --- a/target/linux/mediatek/patches-5.15/734-net-phy-mediatek-ge-soc-sync-driver-with-MediaTek-SD.patch +++ /dev/null @@ -1,270 +0,0 @@ -From f2195279c234c0f618946424b8236026126bc595 Mon Sep 17 00:00:00 2001 -Message-ID: -From: Daniel Golle -Date: Wed, 24 Jan 2024 02:27:04 +0000 -Subject: [PATCH net] net: phy: mediatek-ge-soc: sync driver with MediaTek SDK -To: Daniel Golle , - Qingfang Deng , - SkyLake Huang , - Andrew Lunn , - Heiner Kallweit , - Russell King , - David S. Miller , - Eric Dumazet , - Jakub Kicinski , - Paolo Abeni , - Matthias Brugger , - AngeloGioacchino Del Regno , - netdev@vger.kernel.org, - linux-kernel@vger.kernel.org, - linux-arm-kernel@lists.infradead.org, - linux-mediatek@lists.infradead.org - -Sync initialization and calibration routines with MediaTek's reference -driver. Improves compliance and resolves link stability issues with -CH340 IoT devices connected to MT798x built-in PHYs. - -Fixes: 98c485eaf509 ("net: phy: add driver for MediaTek SoC built-in GE PHYs") -Signed-off-by: Daniel Golle ---- - drivers/net/phy/mediatek-ge-soc.c | 147 ++++++++++++++++-------------- - 1 file changed, 81 insertions(+), 66 deletions(-) - ---- a/drivers/net/phy/mediatek-ge-soc.c -+++ b/drivers/net/phy/mediatek-ge-soc.c -@@ -479,7 +479,7 @@ static int tx_r50_fill_result(struct phy - u16 reg, val; - - if (phydev->drv->phy_id == MTK_GPHY_ID_MT7988) -- bias = -2; -+ bias = -1; - - val = clamp_val(bias + tx_r50_cal_val, 0, 63); - -@@ -695,6 +695,11 @@ restore: - static void mt798x_phy_common_finetune(struct phy_device *phydev) - { - phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); -+ /* SlvDSPreadyTime = 24, MasDSPreadyTime = 24 */ -+ __phy_write(phydev, 0x11, 0xc71); -+ __phy_write(phydev, 0x12, 0xc); -+ __phy_write(phydev, 0x10, 0x8fae); -+ - /* EnabRandUpdTrig = 1 */ - __phy_write(phydev, 0x11, 0x2f00); - __phy_write(phydev, 0x12, 0xe); -@@ -705,15 +710,56 @@ static void mt798x_phy_common_finetune(s - __phy_write(phydev, 0x12, 0x0); - __phy_write(phydev, 0x10, 0x83aa); - -- /* TrFreeze = 0 */ -+ /* FfeUpdGainForce = 1(Enable), FfeUpdGainForceVal = 4 */ -+ __phy_write(phydev, 0x11, 0x240); -+ __phy_write(phydev, 0x12, 0x0); -+ __phy_write(phydev, 0x10, 0x9680); -+ -+ /* TrFreeze = 0 (mt7988 default) */ - __phy_write(phydev, 0x11, 0x0); - __phy_write(phydev, 0x12, 0x0); - __phy_write(phydev, 0x10, 0x9686); - -+ /* SSTrKp100 = 5 */ -+ /* SSTrKf100 = 6 */ -+ /* SSTrKp1000Mas = 5 */ -+ /* SSTrKf1000Mas = 6 */ - /* SSTrKp1000Slv = 5 */ -+ /* SSTrKf1000Slv = 6 */ - __phy_write(phydev, 0x11, 0xbaef); - __phy_write(phydev, 0x12, 0x2e); - __phy_write(phydev, 0x10, 0x968c); -+ phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); -+} -+ -+static void mt7981_phy_finetune(struct phy_device *phydev) -+{ -+ u16 val[8] = { 0x01ce, 0x01c1, -+ 0x020f, 0x0202, -+ 0x03d0, 0x03c0, -+ 0x0013, 0x0005 }; -+ int i, k; -+ -+ /* 100M eye finetune: -+ * Keep middle level of TX MLT3 shapper as default. -+ * Only change TX MLT3 overshoot level here. -+ */ -+ for (k = 0, i = 1; i < 12; i++) { -+ if (i % 3 == 0) -+ continue; -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, i, val[k++]); -+ } -+ -+ phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); -+ /* ResetSyncOffset = 6 */ -+ __phy_write(phydev, 0x11, 0x600); -+ __phy_write(phydev, 0x12, 0x0); -+ __phy_write(phydev, 0x10, 0x8fc0); -+ -+ /* VgaDecRate = 1 */ -+ __phy_write(phydev, 0x11, 0x4c2a); -+ __phy_write(phydev, 0x12, 0x3e); -+ __phy_write(phydev, 0x10, 0x8fa4); - - /* MrvlTrFix100Kp = 3, MrvlTrFix100Kf = 2, - * MrvlTrFix1000Kp = 3, MrvlTrFix1000Kf = 2 -@@ -728,7 +774,7 @@ static void mt798x_phy_common_finetune(s - __phy_write(phydev, 0x10, 0x8ec0); - phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); - -- /* TR_OPEN_LOOP_EN = 1, lpf_x_average = 9*/ -+ /* TR_OPEN_LOOP_EN = 1, lpf_x_average = 9 */ - phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG234, - MTK_PHY_TR_OPEN_LOOP_EN_MASK | MTK_PHY_LPF_X_AVERAGE_MASK, - BIT(0) | FIELD_PREP(MTK_PHY_LPF_X_AVERAGE_MASK, 0x9)); -@@ -761,48 +807,6 @@ static void mt798x_phy_common_finetune(s - phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_LDO_OUTPUT_V, 0x2222); - } - --static void mt7981_phy_finetune(struct phy_device *phydev) --{ -- u16 val[8] = { 0x01ce, 0x01c1, -- 0x020f, 0x0202, -- 0x03d0, 0x03c0, -- 0x0013, 0x0005 }; -- int i, k; -- -- /* 100M eye finetune: -- * Keep middle level of TX MLT3 shapper as default. -- * Only change TX MLT3 overshoot level here. -- */ -- for (k = 0, i = 1; i < 12; i++) { -- if (i % 3 == 0) -- continue; -- phy_write_mmd(phydev, MDIO_MMD_VEND1, i, val[k++]); -- } -- -- phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); -- /* SlvDSPreadyTime = 24, MasDSPreadyTime = 24 */ -- __phy_write(phydev, 0x11, 0xc71); -- __phy_write(phydev, 0x12, 0xc); -- __phy_write(phydev, 0x10, 0x8fae); -- -- /* ResetSyncOffset = 6 */ -- __phy_write(phydev, 0x11, 0x600); -- __phy_write(phydev, 0x12, 0x0); -- __phy_write(phydev, 0x10, 0x8fc0); -- -- /* VgaDecRate = 1 */ -- __phy_write(phydev, 0x11, 0x4c2a); -- __phy_write(phydev, 0x12, 0x3e); -- __phy_write(phydev, 0x10, 0x8fa4); -- -- /* FfeUpdGainForce = 4 */ -- __phy_write(phydev, 0x11, 0x240); -- __phy_write(phydev, 0x12, 0x0); -- __phy_write(phydev, 0x10, 0x9680); -- -- phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); --} -- - static void mt7988_phy_finetune(struct phy_device *phydev) - { - u16 val[12] = { 0x0187, 0x01cd, 0x01c8, 0x0182, -@@ -817,17 +821,7 @@ static void mt7988_phy_finetune(struct p - /* TCT finetune */ - phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_TX_FILTER, 0x5); - -- /* Disable TX power saving */ -- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG7, -- MTK_PHY_DA_AD_BUF_BIAS_LP_MASK, 0x3 << 8); -- - phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_52B5); -- -- /* SlvDSPreadyTime = 24, MasDSPreadyTime = 12 */ -- __phy_write(phydev, 0x11, 0x671); -- __phy_write(phydev, 0x12, 0xc); -- __phy_write(phydev, 0x10, 0x8fae); -- - /* ResetSyncOffset = 5 */ - __phy_write(phydev, 0x11, 0x500); - __phy_write(phydev, 0x12, 0x0); -@@ -835,13 +829,27 @@ static void mt7988_phy_finetune(struct p - - /* VgaDecRate is 1 at default on mt7988 */ - -- phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); -+ /* MrvlTrFix100Kp = 6, MrvlTrFix100Kf = 7, -+ * MrvlTrFix1000Kp = 6, MrvlTrFix1000Kf = 7 -+ */ -+ __phy_write(phydev, 0x11, 0xb90a); -+ __phy_write(phydev, 0x12, 0x6f); -+ __phy_write(phydev, 0x10, 0x8f82); -+ -+ /* RemAckCntLimitCtrl = 1 */ -+ __phy_write(phydev, 0x11, 0xfbba); -+ __phy_write(phydev, 0x12, 0xc3); -+ __phy_write(phydev, 0x10, 0x87f8); - -- phy_select_page(phydev, MTK_PHY_PAGE_EXTENDED_2A30); -- /* TxClkOffset = 2 */ -- __phy_modify(phydev, MTK_PHY_ANARG_RG, MTK_PHY_TCLKOFFSET_MASK, -- FIELD_PREP(MTK_PHY_TCLKOFFSET_MASK, 0x2)); - phy_restore_page(phydev, MTK_PHY_PAGE_STANDARD, 0); -+ -+ /* TR_OPEN_LOOP_EN = 1, lpf_x_average = 10 */ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG234, -+ MTK_PHY_TR_OPEN_LOOP_EN_MASK | MTK_PHY_LPF_X_AVERAGE_MASK, -+ BIT(0) | FIELD_PREP(MTK_PHY_LPF_X_AVERAGE_MASK, 0xa)); -+ -+ /* rg_tr_lpf_cnt_val = 1023 */ -+ phy_write_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_LPF_CNT_VAL, 0x3ff); - } - - static void mt798x_phy_eee(struct phy_device *phydev) -@@ -874,11 +882,11 @@ static void mt798x_phy_eee(struct phy_de - MTK_PHY_LPI_SLV_SEND_TX_EN, - FIELD_PREP(MTK_PHY_LPI_SLV_SEND_TX_TIMER_MASK, 0x120)); - -- phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG239, -- MTK_PHY_LPI_SEND_LOC_TIMER_MASK | -- MTK_PHY_LPI_TXPCS_LOC_RCV, -- FIELD_PREP(MTK_PHY_LPI_SEND_LOC_TIMER_MASK, 0x117)); -+ /* Keep MTK_PHY_LPI_SEND_LOC_TIMER as 375 */ -+ phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG239, -+ MTK_PHY_LPI_TXPCS_LOC_RCV); - -+ /* This also fixes some IoT issues, such as CH340 */ - phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RG_DEV1E_REG2C7, - MTK_PHY_MAX_GAIN_MASK | MTK_PHY_MIN_GAIN_MASK, - FIELD_PREP(MTK_PHY_MAX_GAIN_MASK, 0x8) | -@@ -912,7 +920,7 @@ static void mt798x_phy_eee(struct phy_de - __phy_write(phydev, 0x12, 0x0); - __phy_write(phydev, 0x10, 0x9690); - -- /* REG_EEE_st2TrKf1000 = 3 */ -+ /* REG_EEE_st2TrKf1000 = 2 */ - __phy_write(phydev, 0x11, 0x114f); - __phy_write(phydev, 0x12, 0x2); - __phy_write(phydev, 0x10, 0x969a); -@@ -937,7 +945,7 @@ static void mt798x_phy_eee(struct phy_de - __phy_write(phydev, 0x12, 0x0); - __phy_write(phydev, 0x10, 0x96b8); - -- /* REGEEE_wake_slv_tr_wait_dfesigdet_en = 1 */ -+ /* REGEEE_wake_slv_tr_wait_dfesigdet_en = 0 */ - __phy_write(phydev, 0x11, 0x1463); - __phy_write(phydev, 0x12, 0x0); - __phy_write(phydev, 0x10, 0x96ca); -@@ -1198,6 +1206,13 @@ static int mt7988_phy_probe(struct phy_d - - mt798x_phy_setup_led(phydev, mt7988_phy_get_boottrap_polarity(phydev)); - -+ /* Disable TX power saving at probing to: -+ * 1. Meet common mode compliance test criteria -+ * 2. Make sure that TX-VCM calibration works fine -+ */ -+ phy_modify_mmd(phydev, MDIO_MMD_VEND1, MTK_PHY_RXADC_CTRL_RG7, -+ MTK_PHY_DA_AD_BUF_BIAS_LP_MASK, 0x3 << 8); -+ - return mt798x_phy_calibration(phydev); - } - diff --git a/target/linux/mediatek/patches-5.15/801-phy-phy-mtk-tphy-Add-PCIe-2-lane-efuse-support.patch b/target/linux/mediatek/patches-5.15/801-phy-phy-mtk-tphy-Add-PCIe-2-lane-efuse-support.patch deleted file mode 100644 index 691a7c0398..0000000000 --- a/target/linux/mediatek/patches-5.15/801-phy-phy-mtk-tphy-Add-PCIe-2-lane-efuse-support.patch +++ /dev/null @@ -1,225 +0,0 @@ -From 41ffe32e7ec23f592e21c508b5108899ad393059 Mon Sep 17 00:00:00 2001 -From: Zhanyong Wang -Date: Tue, 25 Jan 2022 16:50:47 +0800 -Subject: [PATCH 4/5] phy: phy-mtk-tphy: Add PCIe 2 lane efuse support - -Add PCIe 2 lane efuse support in tphy driver. - -Signed-off-by: Jie Yang -Signed-off-by: Zhanyong Wang ---- - drivers/phy/mediatek/phy-mtk-tphy.c | 140 ++++++++++++++++++++++++++++ - 1 file changed, 140 insertions(+) - ---- a/drivers/phy/mediatek/phy-mtk-tphy.c -+++ b/drivers/phy/mediatek/phy-mtk-tphy.c -@@ -44,6 +44,15 @@ - #define SSUSB_SIFSLV_V2_U3PHYD 0x200 - #define SSUSB_SIFSLV_V2_U3PHYA 0x400 - -+/* version V4 sub-banks offset base address */ -+/* pcie phy banks */ -+#define SSUSB_SIFSLV_V4_SPLLC 0x000 -+#define SSUSB_SIFSLV_V4_CHIP 0x100 -+#define SSUSB_SIFSLV_V4_U3PHYD 0x900 -+#define SSUSB_SIFSLV_V4_U3PHYA 0xb00 -+ -+#define SSUSB_LN1_OFFSET 0x10000 -+ - #define U3P_MISC_REG1 0x04 - #define MR1_EFUSE_AUTO_LOAD_DIS BIT(6) - -@@ -320,6 +329,7 @@ enum mtk_phy_version { - MTK_PHY_V1 = 1, - MTK_PHY_V2, - MTK_PHY_V3, -+ MTK_PHY_V4, - }; - - struct mtk_phy_pdata { -@@ -369,6 +379,9 @@ struct mtk_phy_instance { - u32 efuse_intr; - u32 efuse_tx_imp; - u32 efuse_rx_imp; -+ u32 efuse_intr_ln1; -+ u32 efuse_tx_imp_ln1; -+ u32 efuse_rx_imp_ln1; - int eye_src; - int eye_vrt; - int eye_term; -@@ -946,6 +959,36 @@ static void phy_v2_banks_init(struct mtk - } - } - -+static void phy_v4_banks_init(struct mtk_tphy *tphy, -+ struct mtk_phy_instance *instance) -+{ -+ struct u2phy_banks *u2_banks = &instance->u2_banks; -+ struct u3phy_banks *u3_banks = &instance->u3_banks; -+ -+ switch (instance->type) { -+ case PHY_TYPE_USB2: -+ u2_banks->misc = instance->port_base + SSUSB_SIFSLV_V2_MISC; -+ u2_banks->fmreg = instance->port_base + SSUSB_SIFSLV_V2_U2FREQ; -+ u2_banks->com = instance->port_base + SSUSB_SIFSLV_V2_U2PHY_COM; -+ break; -+ case PHY_TYPE_USB3: -+ u3_banks->spllc = instance->port_base + SSUSB_SIFSLV_V2_SPLLC; -+ u3_banks->chip = instance->port_base + SSUSB_SIFSLV_V2_CHIP; -+ u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V2_U3PHYD; -+ u3_banks->phya = instance->port_base + SSUSB_SIFSLV_V2_U3PHYA; -+ break; -+ case PHY_TYPE_PCIE: -+ u3_banks->spllc = instance->port_base + SSUSB_SIFSLV_V4_SPLLC; -+ u3_banks->chip = instance->port_base + SSUSB_SIFSLV_V4_CHIP; -+ u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V4_U3PHYD; -+ u3_banks->phya = instance->port_base + SSUSB_SIFSLV_V4_U3PHYA; -+ break; -+ default: -+ dev_err(tphy->dev, "incompatible PHY type\n"); -+ return; -+ } -+} -+ - static void phy_parse_property(struct mtk_tphy *tphy, - struct mtk_phy_instance *instance) - { -@@ -1144,6 +1187,40 @@ static int phy_efuse_get(struct mtk_tphy - - dev_dbg(dev, "u3 efuse - intr %x, rx_imp %x, tx_imp %x\n", - instance->efuse_intr, instance->efuse_rx_imp,instance->efuse_tx_imp); -+ -+ if (tphy->pdata->version != MTK_PHY_V4) -+ break; -+ -+ ret = nvmem_cell_read_variable_le_u32(dev, "intr_ln1", &instance->efuse_intr_ln1); -+ if (ret) { -+ dev_err(dev, "fail to get u3 lane1 intr efuse, %d\n", ret); -+ break; -+ } -+ -+ ret = nvmem_cell_read_variable_le_u32(dev, "rx_imp_ln1", &instance->efuse_rx_imp_ln1); -+ if (ret) { -+ dev_err(dev, "fail to get u3 lane1 rx_imp efuse, %d\n", ret); -+ break; -+ } -+ -+ ret = nvmem_cell_read_variable_le_u32(dev, "tx_imp_ln1", &instance->efuse_tx_imp_ln1); -+ if (ret) { -+ dev_err(dev, "fail to get u3 lane1 tx_imp efuse, %d\n", ret); -+ break; -+ } -+ -+ /* no efuse, ignore it */ -+ if (!instance->efuse_intr_ln1 && -+ !instance->efuse_rx_imp_ln1 && -+ !instance->efuse_tx_imp_ln1) { -+ dev_warn(dev, "no u3 lane1 efuse, but dts enable it\n"); -+ instance->efuse_sw_en = 0; -+ break; -+ } -+ -+ dev_info(dev, "u3 lane1 efuse - intr %x, rx_imp %x, tx_imp %x\n", -+ instance->efuse_intr_ln1, instance->efuse_rx_imp_ln1, -+ instance->efuse_tx_imp_ln1); - break; - default: - dev_err(dev, "no sw efuse for type %d\n", instance->type); -@@ -1175,6 +1252,31 @@ static void phy_efuse_set(struct mtk_phy - writel(tmp, u2_banks->com + U3P_USBPHYACR1); - break; - case PHY_TYPE_USB3: -+ tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RSV); -+ tmp |= P3D_RG_EFUSE_AUTO_LOAD_DIS; -+ writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RSV); -+ -+ tmp = readl(u3_banks->phyd + U3P_U3_PHYD_IMPCAL0); -+ tmp &= ~P3D_RG_TX_IMPEL; -+ tmp |= P3D_RG_TX_IMPEL_VAL(instance->efuse_tx_imp); -+ tmp |= P3D_RG_FORCE_TX_IMPEL; -+ writel(tmp, u3_banks->phyd + U3P_U3_PHYD_IMPCAL0); -+ -+ tmp = readl(u3_banks->phyd + U3P_U3_PHYD_IMPCAL1); -+ tmp &= ~P3D_RG_RX_IMPEL; -+ tmp |= P3D_RG_RX_IMPEL_VAL(instance->efuse_rx_imp); -+ tmp |= P3D_RG_FORCE_RX_IMPEL; -+ writel(tmp, u3_banks->phyd + U3P_U3_PHYD_IMPCAL1); -+ -+ tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG0); -+ tmp &= ~P3A_RG_IEXT_INTR; -+ tmp |= P3A_RG_IEXT_INTR_VAL(instance->efuse_intr); -+ writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG0); -+ pr_err("%s set efuse, tx_imp %x, rx_imp %x intr %x\n", -+ __func__, instance->efuse_tx_imp, -+ instance->efuse_rx_imp, instance->efuse_intr); -+ -+ break; - case PHY_TYPE_PCIE: - tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RSV); - tmp |= P3D_RG_EFUSE_AUTO_LOAD_DIS; -@@ -1196,6 +1298,34 @@ static void phy_efuse_set(struct mtk_phy - tmp &= ~P3A_RG_IEXT_INTR; - tmp |= P3A_RG_IEXT_INTR_VAL(instance->efuse_intr); - writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG0); -+ if (!instance->efuse_intr_ln1 && -+ !instance->efuse_rx_imp_ln1 && -+ !instance->efuse_tx_imp_ln1) -+ break; -+ -+ tmp = readl(u3_banks->phyd + SSUSB_LN1_OFFSET + U3P_U3_PHYD_RSV); -+ tmp |= P3D_RG_EFUSE_AUTO_LOAD_DIS; -+ writel(tmp, u3_banks->phyd + SSUSB_LN1_OFFSET + U3P_U3_PHYD_RSV); -+ -+ tmp = readl(u3_banks->phyd + SSUSB_LN1_OFFSET + U3P_U3_PHYD_IMPCAL0); -+ tmp &= ~P3D_RG_TX_IMPEL; -+ tmp |= P3D_RG_TX_IMPEL_VAL(instance->efuse_tx_imp_ln1); -+ tmp |= P3D_RG_FORCE_TX_IMPEL; -+ writel(tmp, u3_banks->phyd + SSUSB_LN1_OFFSET + U3P_U3_PHYD_IMPCAL0); -+ -+ tmp = readl(u3_banks->phyd + SSUSB_LN1_OFFSET + U3P_U3_PHYD_IMPCAL1); -+ tmp &= ~P3D_RG_RX_IMPEL; -+ tmp |= P3D_RG_RX_IMPEL_VAL(instance->efuse_rx_imp_ln1); -+ tmp |= P3D_RG_FORCE_RX_IMPEL; -+ writel(tmp, u3_banks->phyd + SSUSB_LN1_OFFSET + U3P_U3_PHYD_IMPCAL1); -+ -+ tmp = readl(u3_banks->phya + SSUSB_LN1_OFFSET + U3P_U3_PHYA_REG0); -+ tmp &= ~P3A_RG_IEXT_INTR; -+ tmp |= P3A_RG_IEXT_INTR_VAL(instance->efuse_intr_ln1); -+ writel(tmp, u3_banks->phya + SSUSB_LN1_OFFSET + U3P_U3_PHYA_REG0); -+ dev_info(dev, "%s set LN1 efuse, tx_imp %x, rx_imp %x intr %x\n", -+ __func__, instance->efuse_tx_imp_ln1, -+ instance->efuse_rx_imp_ln1, instance->efuse_intr_ln1); - break; - default: - dev_warn(dev, "no sw efuse for type %d\n", instance->type); -@@ -1335,6 +1465,9 @@ static struct phy *mtk_phy_xlate(struct - case MTK_PHY_V3: - phy_v2_banks_init(tphy, instance); - break; -+ case MTK_PHY_V4: -+ phy_v4_banks_init(tphy, instance); -+ break; - default: - dev_err(dev, "phy version is not supported\n"); - return ERR_PTR(-EINVAL); -@@ -1375,6 +1508,12 @@ static const struct mtk_phy_pdata tphy_v - .version = MTK_PHY_V3, - }; - -+static const struct mtk_phy_pdata tphy_v4_pdata = { -+ .avoid_rx_sen_degradation = false, -+ .sw_efuse_supported = true, -+ .version = MTK_PHY_V4, -+}; -+ - static const struct mtk_phy_pdata mt8173_pdata = { - .avoid_rx_sen_degradation = true, - .version = MTK_PHY_V1, -@@ -1394,6 +1533,7 @@ static const struct of_device_id mtk_tph - { .compatible = "mediatek,generic-tphy-v1", .data = &tphy_v1_pdata }, - { .compatible = "mediatek,generic-tphy-v2", .data = &tphy_v2_pdata }, - { .compatible = "mediatek,generic-tphy-v3", .data = &tphy_v3_pdata }, -+ { .compatible = "mediatek,generic-tphy-v4", .data = &tphy_v4_pdata }, - { }, - }; - MODULE_DEVICE_TABLE(of, mtk_tphy_id_table); diff --git a/target/linux/mediatek/patches-5.15/802-phy-phy-mtk-tphy-add-auto-load-valid-check-mechanism.patch b/target/linux/mediatek/patches-5.15/802-phy-phy-mtk-tphy-add-auto-load-valid-check-mechanism.patch deleted file mode 100644 index 3b8285bf47..0000000000 --- a/target/linux/mediatek/patches-5.15/802-phy-phy-mtk-tphy-add-auto-load-valid-check-mechanism.patch +++ /dev/null @@ -1,149 +0,0 @@ -From 1d5819e90f2ef6dead11809744372a9863227a92 Mon Sep 17 00:00:00 2001 -From: Zhanyong Wang -Date: Tue, 25 Jan 2022 19:03:34 +0800 -Subject: [PATCH 5/5] phy: phy-mtk-tphy: add auto-load-valid check mechanism - support - -add auto-load-valid check mechanism support - -Signed-off-by: Zhanyong Wang ---- - drivers/phy/mediatek/phy-mtk-tphy.c | 67 +++++++++++++++++++++++++++-- - 1 file changed, 64 insertions(+), 3 deletions(-) - ---- a/drivers/phy/mediatek/phy-mtk-tphy.c -+++ b/drivers/phy/mediatek/phy-mtk-tphy.c -@@ -376,9 +376,13 @@ struct mtk_phy_instance { - u32 type_sw_reg; - u32 type_sw_index; - u32 efuse_sw_en; -+ bool efuse_alv_en; -+ u32 efuse_autoloadvalid; - u32 efuse_intr; - u32 efuse_tx_imp; - u32 efuse_rx_imp; -+ bool efuse_alv_ln1_en; -+ u32 efuse_ln1_autoloadvalid; - u32 efuse_intr_ln1; - u32 efuse_tx_imp_ln1; - u32 efuse_rx_imp_ln1; -@@ -1126,6 +1130,7 @@ static int phy_efuse_get(struct mtk_tphy - { - struct device *dev = &instance->phy->dev; - int ret = 0; -+ bool alv = false; - - /* tphy v1 doesn't support sw efuse, skip it */ - if (!tphy->pdata->sw_efuse_supported) { -@@ -1140,6 +1145,20 @@ static int phy_efuse_get(struct mtk_tphy - - switch (instance->type) { - case PHY_TYPE_USB2: -+ alv = of_property_read_bool(dev->of_node, "auto_load_valid"); -+ if (alv) { -+ instance->efuse_alv_en = alv; -+ ret = nvmem_cell_read_variable_le_u32(dev, "auto_load_valid", -+ &instance->efuse_autoloadvalid); -+ if (ret) { -+ dev_err(dev, "fail to get u2 alv efuse, %d\n", ret); -+ break; -+ } -+ dev_info(dev, -+ "u2 auto load valid efuse: ENABLE with value: %u\n", -+ instance->efuse_autoloadvalid); -+ } -+ - ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr); - if (ret) { - dev_err(dev, "fail to get u2 intr efuse, %d\n", ret); -@@ -1158,6 +1177,20 @@ static int phy_efuse_get(struct mtk_tphy - - case PHY_TYPE_USB3: - case PHY_TYPE_PCIE: -+ alv = of_property_read_bool(dev->of_node, "auto_load_valid"); -+ if (alv) { -+ instance->efuse_alv_en = alv; -+ ret = nvmem_cell_read_variable_le_u32(dev, "auto_load_valid", -+ &instance->efuse_autoloadvalid); -+ if (ret) { -+ dev_err(dev, "fail to get u3(pcei) alv efuse, %d\n", ret); -+ break; -+ } -+ dev_info(dev, -+ "u3 auto load valid efuse: ENABLE with value: %u\n", -+ instance->efuse_autoloadvalid); -+ } -+ - ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr); - if (ret) { - dev_err(dev, "fail to get u3 intr efuse, %d\n", ret); -@@ -1191,6 +1224,20 @@ static int phy_efuse_get(struct mtk_tphy - if (tphy->pdata->version != MTK_PHY_V4) - break; - -+ alv = of_property_read_bool(dev->of_node, "auto_load_valid_ln1"); -+ if (alv) { -+ instance->efuse_alv_ln1_en = alv; -+ ret = nvmem_cell_read_variable_le_u32(dev, "auto_load_valid_ln1", -+ &instance->efuse_ln1_autoloadvalid); -+ if (ret) { -+ dev_err(dev, "fail to get pcie auto_load_valid efuse, %d\n", ret); -+ break; -+ } -+ dev_info(dev, -+ "pcie auto load valid efuse: ENABLE with value: %u\n", -+ instance->efuse_ln1_autoloadvalid); -+ } -+ - ret = nvmem_cell_read_variable_le_u32(dev, "intr_ln1", &instance->efuse_intr_ln1); - if (ret) { - dev_err(dev, "fail to get u3 lane1 intr efuse, %d\n", ret); -@@ -1242,6 +1289,10 @@ static void phy_efuse_set(struct mtk_phy - - switch (instance->type) { - case PHY_TYPE_USB2: -+ if (instance->efuse_alv_en && -+ instance->efuse_autoloadvalid == 1) -+ break; -+ - tmp = readl(u2_banks->misc + U3P_MISC_REG1); - tmp |= MR1_EFUSE_AUTO_LOAD_DIS; - writel(tmp, u2_banks->misc + U3P_MISC_REG1); -@@ -1252,6 +1303,10 @@ static void phy_efuse_set(struct mtk_phy - writel(tmp, u2_banks->com + U3P_USBPHYACR1); - break; - case PHY_TYPE_USB3: -+ if (instance->efuse_alv_en && -+ instance->efuse_autoloadvalid == 1) -+ break; -+ - tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RSV); - tmp |= P3D_RG_EFUSE_AUTO_LOAD_DIS; - writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RSV); -@@ -1278,6 +1333,10 @@ static void phy_efuse_set(struct mtk_phy - - break; - case PHY_TYPE_PCIE: -+ if (instance->efuse_alv_en && -+ instance->efuse_autoloadvalid == 1) -+ break; -+ - tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RSV); - tmp |= P3D_RG_EFUSE_AUTO_LOAD_DIS; - writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RSV); -@@ -1298,9 +1357,12 @@ static void phy_efuse_set(struct mtk_phy - tmp &= ~P3A_RG_IEXT_INTR; - tmp |= P3A_RG_IEXT_INTR_VAL(instance->efuse_intr); - writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG0); -- if (!instance->efuse_intr_ln1 && -- !instance->efuse_rx_imp_ln1 && -- !instance->efuse_tx_imp_ln1) -+ -+ if ((!instance->efuse_intr_ln1 && -+ !instance->efuse_rx_imp_ln1 && -+ !instance->efuse_tx_imp_ln1) || -+ (instance->efuse_alv_ln1_en && -+ instance->efuse_ln1_autoloadvalid == 1)) - break; - - tmp = readl(u3_banks->phyd + SSUSB_LN1_OFFSET + U3P_U3_PHYD_RSV); diff --git a/target/linux/mediatek/patches-5.15/804-pwm-add-mt7986-support.patch b/target/linux/mediatek/patches-5.15/804-pwm-add-mt7986-support.patch deleted file mode 100644 index 7a10dac051..0000000000 --- a/target/linux/mediatek/patches-5.15/804-pwm-add-mt7986-support.patch +++ /dev/null @@ -1,23 +0,0 @@ ---- a/drivers/pwm/pwm-mediatek.c -+++ b/drivers/pwm/pwm-mediatek.c -@@ -302,6 +302,12 @@ static const struct pwm_mediatek_of_data - .has_ck_26m_sel = true, - }; - -+static const struct pwm_mediatek_of_data mt7986_pwm_data = { -+ .num_pwms = 2, -+ .pwm45_fixup = false, -+ .has_ck_26m_sel = true, -+}; -+ - static const struct pwm_mediatek_of_data mt8516_pwm_data = { - .num_pwms = 5, - .pwm45_fixup = false, -@@ -314,6 +320,7 @@ static const struct of_device_id pwm_med - { .compatible = "mediatek,mt7623-pwm", .data = &mt7623_pwm_data }, - { .compatible = "mediatek,mt7628-pwm", .data = &mt7628_pwm_data }, - { .compatible = "mediatek,mt7629-pwm", .data = &mt7629_pwm_data }, -+ { .compatible = "mediatek,mt7986-pwm", .data = &mt7986_pwm_data }, - { .compatible = "mediatek,mt8183-pwm", .data = &mt8183_pwm_data }, - { .compatible = "mediatek,mt8516-pwm", .data = &mt8516_pwm_data }, - { }, diff --git a/target/linux/mediatek/patches-5.15/805-v6.2-thermal-drivers-mtk-use-function-pointer-for-raw_to_.patch b/target/linux/mediatek/patches-5.15/805-v6.2-thermal-drivers-mtk-use-function-pointer-for-raw_to_.patch deleted file mode 100644 index c58ae96403..0000000000 --- a/target/linux/mediatek/patches-5.15/805-v6.2-thermal-drivers-mtk-use-function-pointer-for-raw_to_.patch +++ /dev/null @@ -1,56 +0,0 @@ -From 69c17529e8418da3eec703dde31e1b01e5b0f7e8 Mon Sep 17 00:00:00 2001 -From: Daniel Golle -Date: Wed, 18 Jan 2023 02:48:41 +0000 -Subject: [PATCH 1/2] thermal/drivers/mtk: use function pointer for - raw_to_mcelsius - -Instead of having if-else logic selecting either raw_to_mcelsius_v1 or -raw_to_mcelsius_v2 in mtk_thermal_bank_temperature introduce a function -pointer raw_to_mcelsius to struct mtk_thermal which is initialized in the -probe function. - -Signed-off-by: Daniel Golle ---- - drivers/thermal/mtk_thermal.c | 17 ++++++++++------- - 1 file changed, 10 insertions(+), 7 deletions(-) - ---- a/drivers/thermal/mtk_thermal.c -+++ b/drivers/thermal/mtk_thermal.c -@@ -292,6 +292,8 @@ struct mtk_thermal { - - const struct mtk_thermal_data *conf; - struct mtk_thermal_bank banks[MAX_NUM_ZONES]; -+ -+ int (*raw_to_mcelsius)(struct mtk_thermal *mt, int sensno, s32 raw); - }; - - /* MT8183 thermal sensor data */ -@@ -656,13 +658,9 @@ static int mtk_thermal_bank_temperature( - for (i = 0; i < conf->bank_data[bank->id].num_sensors; i++) { - raw = readl(mt->thermal_base + conf->msr[i]); - -- if (mt->conf->version == MTK_THERMAL_V1) { -- temp = raw_to_mcelsius_v1( -- mt, conf->bank_data[bank->id].sensors[i], raw); -- } else { -- temp = raw_to_mcelsius_v2( -- mt, conf->bank_data[bank->id].sensors[i], raw); -- } -+ temp = mt->raw_to_mcelsius( -+ mt, conf->bank_data[bank->id].sensors[i], raw); -+ - - /* - * The first read of a sensor often contains very high bogus -@@ -1075,6 +1073,11 @@ static int mtk_thermal_probe(struct plat - mtk_thermal_release_periodic_ts(mt, auxadc_base); - } - -+ if (mt->conf->version == MTK_THERMAL_V1) -+ mt->raw_to_mcelsius = raw_to_mcelsius_v1; -+ else -+ mt->raw_to_mcelsius = raw_to_mcelsius_v2; -+ - for (ctrl_id = 0; ctrl_id < mt->conf->num_controller ; ctrl_id++) - for (i = 0; i < mt->conf->num_banks; i++) - mtk_thermal_init_bank(mt, i, apmixed_phys_base, diff --git a/target/linux/mediatek/patches-5.15/806-v6.2-thermal-mediatek-add-support-for-MT7986-and-MT7981.patch b/target/linux/mediatek/patches-5.15/806-v6.2-thermal-mediatek-add-support-for-MT7986-and-MT7981.patch deleted file mode 100644 index 65311d5718..0000000000 --- a/target/linux/mediatek/patches-5.15/806-v6.2-thermal-mediatek-add-support-for-MT7986-and-MT7981.patch +++ /dev/null @@ -1,240 +0,0 @@ -From aa957c759b1182aee00cc35178667f849f941b42 Mon Sep 17 00:00:00 2001 -From: Daniel Golle -Date: Wed, 30 Nov 2022 13:19:39 +0000 -Subject: [PATCH 2/2] thermal: mediatek: add support for MT7986 and MT7981 - -Add support for V3 generation thermal found in MT7986 and MT7981 SoCs. -Brings code to assign values from efuse as well as new function to -convert raw temperature to millidegree celsius, as found in MediaTek's -SDK sources (but cleaned up and de-duplicated) - -[1]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/baf36c7eef477aae1f8f2653b6c29e2caf48475b -Signed-off-by: Daniel Golle ---- - drivers/thermal/mtk_thermal.c | 137 ++++++++++++++++++++++++++++++++-- - 1 file changed, 132 insertions(+), 5 deletions(-) - ---- a/drivers/thermal/mtk_thermal.c -+++ b/drivers/thermal/mtk_thermal.c -@@ -150,6 +150,20 @@ - #define CALIB_BUF1_VALID_V2(x) (((x) >> 4) & 0x1) - #define CALIB_BUF1_O_SLOPE_SIGN_V2(x) (((x) >> 3) & 0x1) - -+/* -+ * Layout of the fuses providing the calibration data -+ * These macros can be used for MT7981 and MT7986. -+ */ -+#define CALIB_BUF0_ADC_GE_V3(x) (((x) >> 0) & 0x3ff) -+#define CALIB_BUF0_DEGC_CALI_V3(x) (((x) >> 20) & 0x3f) -+#define CALIB_BUF0_O_SLOPE_V3(x) (((x) >> 26) & 0x3f) -+#define CALIB_BUF1_VTS_TS1_V3(x) (((x) >> 0) & 0x1ff) -+#define CALIB_BUF1_VTS_TS2_V3(x) (((x) >> 21) & 0x1ff) -+#define CALIB_BUF1_VTS_TSABB_V3(x) (((x) >> 9) & 0x1ff) -+#define CALIB_BUF1_VALID_V3(x) (((x) >> 18) & 0x1) -+#define CALIB_BUF1_O_SLOPE_SIGN_V3(x) (((x) >> 19) & 0x1) -+#define CALIB_BUF1_ID_V3(x) (((x) >> 20) & 0x1) -+ - enum { - VTS1, - VTS2, -@@ -163,6 +177,7 @@ enum { - enum mtk_thermal_version { - MTK_THERMAL_V1 = 1, - MTK_THERMAL_V2, -+ MTK_THERMAL_V3, - }; - - /* MT2701 thermal sensors */ -@@ -245,6 +260,27 @@ enum mtk_thermal_version { - /* The calibration coefficient of sensor */ - #define MT8183_CALIBRATION 153 - -+/* AUXADC channel 11 is used for the temperature sensors */ -+#define MT7986_TEMP_AUXADC_CHANNEL 11 -+ -+/* The total number of temperature sensors in the MT7986 */ -+#define MT7986_NUM_SENSORS 1 -+ -+/* The number of banks in the MT7986 */ -+#define MT7986_NUM_ZONES 1 -+ -+/* The number of sensing points per bank */ -+#define MT7986_NUM_SENSORS_PER_ZONE 1 -+ -+/* MT7986 thermal sensors */ -+#define MT7986_TS1 0 -+ -+/* The number of controller in the MT7986 */ -+#define MT7986_NUM_CONTROLLER 1 -+ -+/* The calibration coefficient of sensor */ -+#define MT7986_CALIBRATION 165 -+ - struct mtk_thermal; - - struct thermal_bank_cfg { -@@ -388,6 +424,14 @@ static const int mt7622_mux_values[MT762 - static const int mt7622_vts_index[MT7622_NUM_SENSORS] = { VTS1 }; - static const int mt7622_tc_offset[MT7622_NUM_CONTROLLER] = { 0x0, }; - -+/* MT7986 thermal sensor data */ -+static const int mt7986_bank_data[MT7986_NUM_SENSORS] = { MT7986_TS1, }; -+static const int mt7986_msr[MT7986_NUM_SENSORS_PER_ZONE] = { TEMP_MSR0, }; -+static const int mt7986_adcpnp[MT7986_NUM_SENSORS_PER_ZONE] = { TEMP_ADCPNP0, }; -+static const int mt7986_mux_values[MT7986_NUM_SENSORS] = { 0, }; -+static const int mt7986_vts_index[MT7986_NUM_SENSORS] = { VTS1 }; -+static const int mt7986_tc_offset[MT7986_NUM_CONTROLLER] = { 0x0, }; -+ - /* - * The MT8173 thermal controller has four banks. Each bank can read up to - * four temperature sensors simultaneously. The MT8173 has a total of 5 -@@ -551,6 +595,30 @@ static const struct mtk_thermal_data mt8 - .version = MTK_THERMAL_V1, - }; - -+/* -+ * MT7986 uses AUXADC Channel 11 for raw data access. -+ */ -+static const struct mtk_thermal_data mt7986_thermal_data = { -+ .auxadc_channel = MT7986_TEMP_AUXADC_CHANNEL, -+ .num_banks = MT7986_NUM_ZONES, -+ .num_sensors = MT7986_NUM_SENSORS, -+ .vts_index = mt7986_vts_index, -+ .cali_val = MT7986_CALIBRATION, -+ .num_controller = MT7986_NUM_CONTROLLER, -+ .controller_offset = mt7986_tc_offset, -+ .need_switch_bank = true, -+ .bank_data = { -+ { -+ .num_sensors = 1, -+ .sensors = mt7986_bank_data, -+ }, -+ }, -+ .msr = mt7986_msr, -+ .adcpnp = mt7986_adcpnp, -+ .sensor_mux_values = mt7986_mux_values, -+ .version = MTK_THERMAL_V3, -+}; -+ - /** - * raw_to_mcelsius - convert a raw ADC value to mcelsius - * @mt: The thermal controller -@@ -605,6 +673,22 @@ static int raw_to_mcelsius_v2(struct mtk - return (format_2 - tmp) * 100; - } - -+static int raw_to_mcelsius_v3(struct mtk_thermal *mt, int sensno, s32 raw) -+{ -+ s32 tmp; -+ -+ if (raw == 0) -+ return 0; -+ -+ raw &= 0xfff; -+ tmp = 100000 * 15 / 16 * 10000; -+ tmp /= 4096 - 512 + mt->adc_ge; -+ tmp /= 1490; -+ tmp *= raw - mt->vts[sensno] - 2900; -+ -+ return mt->degc_cali * 500 - tmp; -+} -+ - /** - * mtk_thermal_get_bank - get bank - * @bank: The bank -@@ -885,6 +969,25 @@ static int mtk_thermal_extract_efuse_v2( - return 0; - } - -+static int mtk_thermal_extract_efuse_v3(struct mtk_thermal *mt, u32 *buf) -+{ -+ if (!CALIB_BUF1_VALID_V3(buf[1])) -+ return -EINVAL; -+ -+ mt->adc_ge = CALIB_BUF0_ADC_GE_V3(buf[0]); -+ mt->degc_cali = CALIB_BUF0_DEGC_CALI_V3(buf[0]); -+ mt->o_slope = CALIB_BUF0_O_SLOPE_V3(buf[0]); -+ mt->vts[VTS1] = CALIB_BUF1_VTS_TS1_V3(buf[1]); -+ mt->vts[VTS2] = CALIB_BUF1_VTS_TS2_V3(buf[1]); -+ mt->vts[VTSABB] = CALIB_BUF1_VTS_TSABB_V3(buf[1]); -+ mt->o_slope_sign = CALIB_BUF1_O_SLOPE_SIGN_V3(buf[1]); -+ -+ if (CALIB_BUF1_ID_V3(buf[1]) == 0) -+ mt->o_slope = 0; -+ -+ return 0; -+} -+ - static int mtk_thermal_get_calibration_data(struct device *dev, - struct mtk_thermal *mt) - { -@@ -895,6 +998,7 @@ static int mtk_thermal_get_calibration_d - - /* Start with default values */ - mt->adc_ge = 512; -+ mt->adc_oe = 512; - for (i = 0; i < mt->conf->num_sensors; i++) - mt->vts[i] = 260; - mt->degc_cali = 40; -@@ -920,10 +1024,20 @@ static int mtk_thermal_get_calibration_d - goto out; - } - -- if (mt->conf->version == MTK_THERMAL_V1) -+ switch (mt->conf->version) { -+ case MTK_THERMAL_V1: - ret = mtk_thermal_extract_efuse_v1(mt, buf); -- else -+ break; -+ case MTK_THERMAL_V2: - ret = mtk_thermal_extract_efuse_v2(mt, buf); -+ break; -+ case MTK_THERMAL_V3: -+ ret = mtk_thermal_extract_efuse_v3(mt, buf); -+ break; -+ default: -+ ret = -EINVAL; -+ break; -+ } - - if (ret) { - dev_info(dev, "Device not calibrated, using default calibration values\n"); -@@ -954,6 +1068,10 @@ static const struct of_device_id mtk_the - .data = (void *)&mt7622_thermal_data, - }, - { -+ .compatible = "mediatek,mt7986-thermal", -+ .data = (void *)&mt7986_thermal_data, -+ }, -+ { - .compatible = "mediatek,mt8183-thermal", - .data = (void *)&mt8183_thermal_data, - }, { -@@ -1068,15 +1186,24 @@ static int mtk_thermal_probe(struct plat - goto err_disable_clk_auxadc; - } - -- if (mt->conf->version == MTK_THERMAL_V2) { -+ if (mt->conf->version != MTK_THERMAL_V1) { - mtk_thermal_turn_on_buffer(apmixed_base); - mtk_thermal_release_periodic_ts(mt, auxadc_base); - } - -- if (mt->conf->version == MTK_THERMAL_V1) -+ switch (mt->conf->version) { -+ case MTK_THERMAL_V1: - mt->raw_to_mcelsius = raw_to_mcelsius_v1; -- else -+ break; -+ case MTK_THERMAL_V2: - mt->raw_to_mcelsius = raw_to_mcelsius_v2; -+ break; -+ case MTK_THERMAL_V3: -+ mt->raw_to_mcelsius = raw_to_mcelsius_v3; -+ break; -+ default: -+ break; -+ } - - for (ctrl_id = 0; ctrl_id < mt->conf->num_controller ; ctrl_id++) - for (i = 0; i < mt->conf->num_banks; i++) diff --git a/target/linux/mediatek/patches-5.15/811-pwm-mediatek-Add-support-for-MT7981.patch b/target/linux/mediatek/patches-5.15/811-pwm-mediatek-Add-support-for-MT7981.patch deleted file mode 100644 index 8f27462cbd..0000000000 --- a/target/linux/mediatek/patches-5.15/811-pwm-mediatek-Add-support-for-MT7981.patch +++ /dev/null @@ -1,122 +0,0 @@ -From 73d20ebc21c562fbe79d02fa0fa38e095e716fa9 Mon Sep 17 00:00:00 2001 -From: Daniel Golle -Date: Wed, 19 Apr 2023 20:25:51 +0100 -Subject: [PATCH] pwm: mediatek: Add support for MT7981 - -The PWM unit on MT7981 uses different register offsets than previous -MediaTek PWM units. Add support for these new offsets and add support -for PWM on MT7981 which has 3 PWM channels, one of them is typically -used for a temperature controlled fan. - -Signed-off-by: Daniel Golle ---- - drivers/pwm/pwm-mediatek.c | 41 ++++++++++++++++++++++++++++++-------- - 1 file changed, 33 insertions(+), 8 deletions(-) - ---- a/drivers/pwm/pwm-mediatek.c -+++ b/drivers/pwm/pwm-mediatek.c -@@ -38,6 +38,7 @@ struct pwm_mediatek_of_data { - unsigned int num_pwms; - bool pwm45_fixup; - bool has_ck_26m_sel; -+ const unsigned int *reg_offset; - }; - - /** -@@ -59,10 +60,14 @@ struct pwm_mediatek_chip { - const struct pwm_mediatek_of_data *soc; - }; - --static const unsigned int pwm_mediatek_reg_offset[] = { -+static const unsigned int mtk_pwm_reg_offset_v1[] = { - 0x0010, 0x0050, 0x0090, 0x00d0, 0x0110, 0x0150, 0x0190, 0x0220 - }; - -+static const unsigned int mtk_pwm_reg_offset_v2[] = { -+ 0x0080, 0x00c0, 0x0100, 0x0140, 0x0180, 0x01c0, 0x0200, 0x0240 -+}; -+ - static inline struct pwm_mediatek_chip * - to_pwm_mediatek_chip(struct pwm_chip *chip) - { -@@ -111,7 +116,7 @@ static inline void pwm_mediatek_writel(s - unsigned int num, unsigned int offset, - u32 value) - { -- writel(value, chip->regs + pwm_mediatek_reg_offset[num] + offset); -+ writel(value, chip->regs + chip->soc->reg_offset[num] + offset); - } - - static int pwm_mediatek_config(struct pwm_chip *chip, struct pwm_device *pwm, -@@ -270,48 +275,63 @@ static const struct pwm_mediatek_of_data - .num_pwms = 8, - .pwm45_fixup = false, - .has_ck_26m_sel = false, -+ .reg_offset = mtk_pwm_reg_offset_v1, - }; - - static const struct pwm_mediatek_of_data mt7622_pwm_data = { - .num_pwms = 6, - .pwm45_fixup = false, - .has_ck_26m_sel = true, -+ .reg_offset = mtk_pwm_reg_offset_v1, - }; - - static const struct pwm_mediatek_of_data mt7623_pwm_data = { - .num_pwms = 5, - .pwm45_fixup = true, - .has_ck_26m_sel = false, -+ .reg_offset = mtk_pwm_reg_offset_v1, - }; - - static const struct pwm_mediatek_of_data mt7628_pwm_data = { - .num_pwms = 4, - .pwm45_fixup = true, - .has_ck_26m_sel = false, -+ .reg_offset = mtk_pwm_reg_offset_v1, - }; - - static const struct pwm_mediatek_of_data mt7629_pwm_data = { - .num_pwms = 1, - .pwm45_fixup = false, - .has_ck_26m_sel = false, -+ .reg_offset = mtk_pwm_reg_offset_v1, - }; - - static const struct pwm_mediatek_of_data mt8183_pwm_data = { - .num_pwms = 4, - .pwm45_fixup = false, - .has_ck_26m_sel = true, -+ .reg_offset = mtk_pwm_reg_offset_v1, -+}; -+ -+static const struct pwm_mediatek_of_data mt7981_pwm_data = { -+ .num_pwms = 3, -+ .pwm45_fixup = false, -+ .has_ck_26m_sel = true, -+ .reg_offset = mtk_pwm_reg_offset_v2, - }; - - static const struct pwm_mediatek_of_data mt7986_pwm_data = { - .num_pwms = 2, - .pwm45_fixup = false, - .has_ck_26m_sel = true, -+ .reg_offset = mtk_pwm_reg_offset_v1, - }; - - static const struct pwm_mediatek_of_data mt8516_pwm_data = { - .num_pwms = 5, - .pwm45_fixup = false, - .has_ck_26m_sel = true, -+ .reg_offset = mtk_pwm_reg_offset_v1, - }; - - static const struct of_device_id pwm_mediatek_of_match[] = { -@@ -320,6 +340,7 @@ static const struct of_device_id pwm_med - { .compatible = "mediatek,mt7623-pwm", .data = &mt7623_pwm_data }, - { .compatible = "mediatek,mt7628-pwm", .data = &mt7628_pwm_data }, - { .compatible = "mediatek,mt7629-pwm", .data = &mt7629_pwm_data }, -+ { .compatible = "mediatek,mt7981-pwm", .data = &mt7981_pwm_data }, - { .compatible = "mediatek,mt7986-pwm", .data = &mt7986_pwm_data }, - { .compatible = "mediatek,mt8183-pwm", .data = &mt8183_pwm_data }, - { .compatible = "mediatek,mt8516-pwm", .data = &mt8516_pwm_data }, diff --git a/target/linux/mediatek/patches-5.15/820-v5.16-dt-bindings-pinctrl-mt8195-add-rsel-define.patch b/target/linux/mediatek/patches-5.15/820-v5.16-dt-bindings-pinctrl-mt8195-add-rsel-define.patch deleted file mode 100644 index f2be737146..0000000000 --- a/target/linux/mediatek/patches-5.15/820-v5.16-dt-bindings-pinctrl-mt8195-add-rsel-define.patch +++ /dev/null @@ -1,33 +0,0 @@ -From 26564c44357e19d03c124550bbd0b5851e6638c2 Mon Sep 17 00:00:00 2001 -From: Zhiyong Tao -Date: Fri, 24 Sep 2021 16:06:28 +0800 -Subject: [PATCH] dt-bindings: pinctrl: mt8195: add rsel define - -This patch adds rsel define for mt8195. - -Signed-off-by: Zhiyong Tao -Acked-by: Rob Herring -Link: https://lore.kernel.org/r/20210924080632.28410-2-zhiyong.tao@mediatek.com -Signed-off-by: Linus Walleij ---- - include/dt-bindings/pinctrl/mt65xx.h | 9 +++++++++ - 1 file changed, 9 insertions(+) - ---- a/include/dt-bindings/pinctrl/mt65xx.h -+++ b/include/dt-bindings/pinctrl/mt65xx.h -@@ -16,6 +16,15 @@ - #define MTK_PUPD_SET_R1R0_10 102 - #define MTK_PUPD_SET_R1R0_11 103 - -+#define MTK_PULL_SET_RSEL_000 200 -+#define MTK_PULL_SET_RSEL_001 201 -+#define MTK_PULL_SET_RSEL_010 202 -+#define MTK_PULL_SET_RSEL_011 203 -+#define MTK_PULL_SET_RSEL_100 204 -+#define MTK_PULL_SET_RSEL_101 205 -+#define MTK_PULL_SET_RSEL_110 206 -+#define MTK_PULL_SET_RSEL_111 207 -+ - #define MTK_DRIVE_2mA 2 - #define MTK_DRIVE_4mA 4 - #define MTK_DRIVE_6mA 6 diff --git a/target/linux/mediatek/patches-5.15/821-v5.16-pinctrl-mediatek-moore-check-if-pin_desc-is-valid-be.patch b/target/linux/mediatek/patches-5.15/821-v5.16-pinctrl-mediatek-moore-check-if-pin_desc-is-valid-be.patch deleted file mode 100644 index aa9f879e3a..0000000000 --- a/target/linux/mediatek/patches-5.15/821-v5.16-pinctrl-mediatek-moore-check-if-pin_desc-is-valid-be.patch +++ /dev/null @@ -1,93 +0,0 @@ -From d8b94c9ff96c2024a527086d850eb0b314337ff9 Mon Sep 17 00:00:00 2001 -From: Sam Shih -Date: Tue, 14 Sep 2021 16:51:32 +0800 -Subject: [PATCH] pinctrl: mediatek: moore: check if pin_desc is valid before - use - -Certain SoC are missing the middle part gpios in consecutive pins, -it's better to check if mtk_pin_desc is a valid pin for the extensibility - -Signed-off-by: Sam Shih -Acked-by: Sean Wang -Link: https://lore.kernel.org/r/20210914085137.31761-5-sam.shih@mediatek.com -Signed-off-by: Linus Walleij ---- - drivers/pinctrl/mediatek/pinctrl-moore.c | 18 ++++++++++++++++++ - 1 file changed, 18 insertions(+) - ---- a/drivers/pinctrl/mediatek/pinctrl-moore.c -+++ b/drivers/pinctrl/mediatek/pinctrl-moore.c -@@ -60,6 +60,8 @@ static int mtk_pinmux_set_mux(struct pin - int pin = grp->pins[i]; - - desc = (const struct mtk_pin_desc *)&hw->soc->pins[pin]; -+ if (!desc->name) -+ return -ENOTSUPP; - - mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_MODE, - pin_modes[i]); -@@ -76,6 +78,8 @@ static int mtk_pinmux_gpio_request_enabl - const struct mtk_pin_desc *desc; - - desc = (const struct mtk_pin_desc *)&hw->soc->pins[pin]; -+ if (!desc->name) -+ return -ENOTSUPP; - - return mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_MODE, - hw->soc->gpio_m); -@@ -89,6 +93,8 @@ static int mtk_pinmux_gpio_set_direction - const struct mtk_pin_desc *desc; - - desc = (const struct mtk_pin_desc *)&hw->soc->pins[pin]; -+ if (!desc->name) -+ return -ENOTSUPP; - - /* hardware would take 0 as input direction */ - return mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_DIR, !input); -@@ -103,6 +109,8 @@ static int mtk_pinconf_get(struct pinctr - const struct mtk_pin_desc *desc; - - desc = (const struct mtk_pin_desc *)&hw->soc->pins[pin]; -+ if (!desc->name) -+ return -ENOTSUPP; - - switch (param) { - case PIN_CONFIG_BIAS_DISABLE: -@@ -218,6 +226,8 @@ static int mtk_pinconf_set(struct pinctr - int cfg, err = 0; - - desc = (const struct mtk_pin_desc *)&hw->soc->pins[pin]; -+ if (!desc->name) -+ return -ENOTSUPP; - - for (cfg = 0; cfg < num_configs; cfg++) { - param = pinconf_to_config_param(configs[cfg]); -@@ -435,6 +445,8 @@ static int mtk_gpio_get(struct gpio_chip - int value, err; - - desc = (const struct mtk_pin_desc *)&hw->soc->pins[gpio]; -+ if (!desc->name) -+ return -ENOTSUPP; - - err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_DI, &value); - if (err) -@@ -449,6 +461,10 @@ static void mtk_gpio_set(struct gpio_chi - const struct mtk_pin_desc *desc; - - desc = (const struct mtk_pin_desc *)&hw->soc->pins[gpio]; -+ if (!desc->name) { -+ dev_err(hw->dev, "Failed to set gpio %d\n", gpio); -+ return; -+ } - - mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_DO, !!value); - } -@@ -490,6 +506,8 @@ static int mtk_gpio_set_config(struct gp - u32 debounce; - - desc = (const struct mtk_pin_desc *)&hw->soc->pins[offset]; -+ if (!desc->name) -+ return -ENOTSUPP; - - if (!hw->eint || - pinconf_to_config_param(config) != PIN_CONFIG_INPUT_DEBOUNCE || diff --git a/target/linux/mediatek/patches-5.15/822-v5.16-pinctrl-mediatek-support-rsel-feature.patch b/target/linux/mediatek/patches-5.15/822-v5.16-pinctrl-mediatek-support-rsel-feature.patch deleted file mode 100644 index 0f5c0495fe..0000000000 --- a/target/linux/mediatek/patches-5.15/822-v5.16-pinctrl-mediatek-support-rsel-feature.patch +++ /dev/null @@ -1,457 +0,0 @@ -From fb34a9ae383ae26326d4889fd2513e49f1019b88 Mon Sep 17 00:00:00 2001 -From: Zhiyong Tao -Date: Fri, 24 Sep 2021 16:06:31 +0800 -Subject: [PATCH] pinctrl: mediatek: support rsel feature - -This patch supports rsel(resistance selection) feature for I2C pins. -It provides more resistance selection solution in different ICs. -It provides rsel define and si unit solution by identifying -"mediatek,rsel_resistance_in_si_unit" property in pio dtsi node. - -Signed-off-by: Zhiyong Tao -Reviewed-by: Chen-Yu Tsai -Link: https://lore.kernel.org/r/20210924080632.28410-5-zhiyong.tao@mediatek.com -Signed-off-by: Linus Walleij ---- - .../pinctrl/mediatek/pinctrl-mtk-common-v2.c | 231 +++++++++++++++--- - .../pinctrl/mediatek/pinctrl-mtk-common-v2.h | 46 ++++ - drivers/pinctrl/mediatek/pinctrl-paris.c | 60 +++-- - 3 files changed, 289 insertions(+), 48 deletions(-) - ---- a/drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c -@@ -665,6 +665,181 @@ out: - return err; - } - -+static int mtk_hw_pin_rsel_lookup(struct mtk_pinctrl *hw, -+ const struct mtk_pin_desc *desc, -+ u32 pullup, u32 arg, u32 *rsel_val) -+{ -+ const struct mtk_pin_rsel *rsel; -+ int check; -+ bool found = false; -+ -+ rsel = hw->soc->pin_rsel; -+ -+ for (check = 0; check <= hw->soc->npin_rsel - 1; check++) { -+ if (desc->number >= rsel[check].s_pin && -+ desc->number <= rsel[check].e_pin) { -+ if (pullup) { -+ if (rsel[check].up_rsel == arg) { -+ found = true; -+ *rsel_val = rsel[check].rsel_index; -+ break; -+ } -+ } else { -+ if (rsel[check].down_rsel == arg) { -+ found = true; -+ *rsel_val = rsel[check].rsel_index; -+ break; -+ } -+ } -+ } -+ } -+ -+ if (!found) { -+ dev_err(hw->dev, "Not support rsel value %d Ohm for pin = %d (%s)\n", -+ arg, desc->number, desc->name); -+ return -ENOTSUPP; -+ } -+ -+ return 0; -+} -+ -+static int mtk_pinconf_bias_set_rsel(struct mtk_pinctrl *hw, -+ const struct mtk_pin_desc *desc, -+ u32 pullup, u32 arg) -+{ -+ int err, rsel_val; -+ -+ if (hw->rsel_si_unit) { -+ /* find pin rsel_index from pin_rsel array*/ -+ err = mtk_hw_pin_rsel_lookup(hw, desc, pullup, arg, &rsel_val); -+ if (err) -+ goto out; -+ } else { -+ if (arg < MTK_PULL_SET_RSEL_000 || -+ arg > MTK_PULL_SET_RSEL_111) { -+ err = -EINVAL; -+ goto out; -+ } -+ -+ rsel_val = arg - MTK_PULL_SET_RSEL_000; -+ } -+ -+ err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_RSEL, rsel_val); -+ if (err) -+ goto out; -+ -+ err = mtk_pinconf_bias_set_pu_pd(hw, desc, pullup, MTK_ENABLE); -+ -+out: -+ return err; -+} -+ -+int mtk_pinconf_bias_set_combo(struct mtk_pinctrl *hw, -+ const struct mtk_pin_desc *desc, -+ u32 pullup, u32 arg) -+{ -+ int err = -ENOTSUPP; -+ u32 try_all_type; -+ -+ if (hw->soc->pull_type) -+ try_all_type = hw->soc->pull_type[desc->number]; -+ else -+ try_all_type = MTK_PULL_TYPE_MASK; -+ -+ if (try_all_type & MTK_PULL_RSEL_TYPE) { -+ err = mtk_pinconf_bias_set_rsel(hw, desc, pullup, arg); -+ if (!err) -+ return err; -+ } -+ -+ if (try_all_type & MTK_PULL_PU_PD_TYPE) { -+ err = mtk_pinconf_bias_set_pu_pd(hw, desc, pullup, arg); -+ if (!err) -+ return err; -+ } -+ -+ if (try_all_type & MTK_PULL_PULLSEL_TYPE) { -+ err = mtk_pinconf_bias_set_pullsel_pullen(hw, desc, -+ pullup, arg); -+ if (!err) -+ return err; -+ } -+ -+ if (try_all_type & MTK_PULL_PUPD_R1R0_TYPE) -+ err = mtk_pinconf_bias_set_pupd_r1_r0(hw, desc, pullup, arg); -+ -+ if (err) -+ dev_err(hw->dev, "Invalid pull argument\n"); -+ -+ return err; -+} -+EXPORT_SYMBOL_GPL(mtk_pinconf_bias_set_combo); -+ -+static int mtk_rsel_get_si_unit(struct mtk_pinctrl *hw, -+ const struct mtk_pin_desc *desc, -+ u32 pullup, u32 rsel_val, u32 *si_unit) -+{ -+ const struct mtk_pin_rsel *rsel; -+ int check; -+ -+ rsel = hw->soc->pin_rsel; -+ -+ for (check = 0; check <= hw->soc->npin_rsel - 1; check++) { -+ if (desc->number >= rsel[check].s_pin && -+ desc->number <= rsel[check].e_pin) { -+ if (rsel_val == rsel[check].rsel_index) { -+ if (pullup) -+ *si_unit = rsel[check].up_rsel; -+ else -+ *si_unit = rsel[check].down_rsel; -+ break; -+ } -+ } -+ } -+ -+ return 0; -+} -+ -+static int mtk_pinconf_bias_get_rsel(struct mtk_pinctrl *hw, -+ const struct mtk_pin_desc *desc, -+ u32 *pullup, u32 *enable) -+{ -+ int pu, pd, rsel, err; -+ -+ err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_RSEL, &rsel); -+ if (err) -+ goto out; -+ -+ err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_PU, &pu); -+ if (err) -+ goto out; -+ -+ err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_PD, &pd); -+ -+ if (pu == 0 && pd == 0) { -+ *pullup = 0; -+ *enable = MTK_DISABLE; -+ } else if (pu == 1 && pd == 0) { -+ *pullup = 1; -+ if (hw->rsel_si_unit) -+ mtk_rsel_get_si_unit(hw, desc, *pullup, rsel, enable); -+ else -+ *enable = rsel + MTK_PULL_SET_RSEL_000; -+ } else if (pu == 0 && pd == 1) { -+ *pullup = 0; -+ if (hw->rsel_si_unit) -+ mtk_rsel_get_si_unit(hw, desc, *pullup, rsel, enable); -+ else -+ *enable = rsel + MTK_PULL_SET_RSEL_000; -+ } else { -+ err = -EINVAL; -+ goto out; -+ } -+ -+out: -+ return err; -+} -+ - static int mtk_pinconf_bias_get_pu_pd(struct mtk_pinctrl *hw, - const struct mtk_pin_desc *desc, - u32 *pullup, u32 *enable) -@@ -746,44 +921,40 @@ out: - return err; - } - --int mtk_pinconf_bias_set_combo(struct mtk_pinctrl *hw, -- const struct mtk_pin_desc *desc, -- u32 pullup, u32 arg) --{ -- int err; -- -- err = mtk_pinconf_bias_set_pu_pd(hw, desc, pullup, arg); -- if (!err) -- goto out; -- -- err = mtk_pinconf_bias_set_pullsel_pullen(hw, desc, pullup, arg); -- if (!err) -- goto out; -- -- err = mtk_pinconf_bias_set_pupd_r1_r0(hw, desc, pullup, arg); -- --out: -- return err; --} --EXPORT_SYMBOL_GPL(mtk_pinconf_bias_set_combo); -- - int mtk_pinconf_bias_get_combo(struct mtk_pinctrl *hw, - const struct mtk_pin_desc *desc, - u32 *pullup, u32 *enable) - { -- int err; -+ int err = -ENOTSUPP; -+ u32 try_all_type; - -- err = mtk_pinconf_bias_get_pu_pd(hw, desc, pullup, enable); -- if (!err) -- goto out; -+ if (hw->soc->pull_type) -+ try_all_type = hw->soc->pull_type[desc->number]; -+ else -+ try_all_type = MTK_PULL_TYPE_MASK; - -- err = mtk_pinconf_bias_get_pullsel_pullen(hw, desc, pullup, enable); -- if (!err) -- goto out; -+ if (try_all_type & MTK_PULL_RSEL_TYPE) { -+ err = mtk_pinconf_bias_get_rsel(hw, desc, pullup, enable); -+ if (!err) -+ return err; -+ } -+ -+ if (try_all_type & MTK_PULL_PU_PD_TYPE) { -+ err = mtk_pinconf_bias_get_pu_pd(hw, desc, pullup, enable); -+ if (!err) -+ return err; -+ } -+ -+ if (try_all_type & MTK_PULL_PULLSEL_TYPE) { -+ err = mtk_pinconf_bias_get_pullsel_pullen(hw, desc, -+ pullup, enable); -+ if (!err) -+ return err; -+ } - -- err = mtk_pinconf_bias_get_pupd_r1_r0(hw, desc, pullup, enable); -+ if (try_all_type & MTK_PULL_PUPD_R1R0_TYPE) -+ err = mtk_pinconf_bias_get_pupd_r1_r0(hw, desc, pullup, enable); - --out: - return err; - } - EXPORT_SYMBOL_GPL(mtk_pinconf_bias_get_combo); ---- a/drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.h -+++ b/drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.h -@@ -17,6 +17,22 @@ - #define MTK_ENABLE 1 - #define MTK_PULLDOWN 0 - #define MTK_PULLUP 1 -+#define MTK_PULL_PU_PD_TYPE BIT(0) -+#define MTK_PULL_PULLSEL_TYPE BIT(1) -+#define MTK_PULL_PUPD_R1R0_TYPE BIT(2) -+/* MTK_PULL_RSEL_TYPE can select resistance and can be -+ * turned on/off itself. But it can't be selected pull up/down -+ */ -+#define MTK_PULL_RSEL_TYPE BIT(3) -+/* MTK_PULL_PU_PD_RSEL_TYPE is a type which is controlled by -+ * MTK_PULL_PU_PD_TYPE and MTK_PULL_RSEL_TYPE. -+ */ -+#define MTK_PULL_PU_PD_RSEL_TYPE (MTK_PULL_PU_PD_TYPE \ -+ | MTK_PULL_RSEL_TYPE) -+#define MTK_PULL_TYPE_MASK (MTK_PULL_PU_PD_TYPE |\ -+ MTK_PULL_PULLSEL_TYPE |\ -+ MTK_PULL_PUPD_R1R0_TYPE |\ -+ MTK_PULL_RSEL_TYPE) - - #define EINT_NA U16_MAX - #define NO_EINT_SUPPORT EINT_NA -@@ -42,6 +58,14 @@ - PIN_FIELD_CALC(_s_pin, _e_pin, 0, _s_addr, _x_addrs, _s_bit, \ - _x_bits, 32, 1) - -+#define PIN_RSEL(_s_pin, _e_pin, _rsel_index, _up_resl, _down_rsel) { \ -+ .s_pin = _s_pin, \ -+ .e_pin = _e_pin, \ -+ .rsel_index = _rsel_index, \ -+ .up_rsel = _up_resl, \ -+ .down_rsel = _down_rsel, \ -+ } -+ - /* List these attributes which could be modified for the pin */ - enum { - PINCTRL_PIN_REG_MODE, -@@ -67,6 +91,7 @@ enum { - PINCTRL_PIN_REG_DRV_E0, - PINCTRL_PIN_REG_DRV_E1, - PINCTRL_PIN_REG_DRV_ADV, -+ PINCTRL_PIN_REG_RSEL, - PINCTRL_PIN_REG_MAX, - }; - -@@ -129,6 +154,22 @@ struct mtk_pin_field_calc { - u8 fixed; - }; - -+/** -+ * struct mtk_pin_rsel - the structure that provides bias resistance selection. -+ * @s_pin: the start pin within the rsel range -+ * @e_pin: the end pin within the rsel range -+ * @rsel_index: the rsel bias resistance index -+ * @up_rsel: the pullup rsel bias resistance value -+ * @down_rsel: the pulldown rsel bias resistance value -+ */ -+struct mtk_pin_rsel { -+ u16 s_pin; -+ u16 e_pin; -+ u16 rsel_index; -+ u32 up_rsel; -+ u32 down_rsel; -+}; -+ - /* struct mtk_pin_reg_calc - the structure that holds all ranges used to - * determine which register the pin would make use of - * for certain pin attribute. -@@ -206,6 +247,9 @@ struct mtk_pin_soc { - bool ies_present; - const char * const *base_names; - unsigned int nbase_names; -+ const unsigned int *pull_type; -+ const struct mtk_pin_rsel *pin_rsel; -+ unsigned int npin_rsel; - - /* Specific pinconfig operations */ - int (*bias_disable_set)(struct mtk_pinctrl *hw, -@@ -254,6 +298,8 @@ struct mtk_pinctrl { - const char **grp_names; - /* lock pin's register resource to avoid multiple threads issue*/ - spinlock_t lock; -+ /* identify rsel setting by si unit or rsel define in dts node */ -+ bool rsel_si_unit; - }; - - void mtk_rmw(struct mtk_pinctrl *pctl, u8 i, u32 reg, u32 mask, u32 set); ---- a/drivers/pinctrl/mediatek/pinctrl-paris.c -+++ b/drivers/pinctrl/mediatek/pinctrl-paris.c -@@ -574,8 +574,9 @@ static int mtk_hw_get_value_wrap(struct - ssize_t mtk_pctrl_show_one_pin(struct mtk_pinctrl *hw, - unsigned int gpio, char *buf, unsigned int buf_len) - { -- int pinmux, pullup = 0, pullen = 0, len = 0, r1 = -1, r0 = -1; -+ int pinmux, pullup = 0, pullen = 0, len = 0, r1 = -1, r0 = -1, rsel = -1; - const struct mtk_pin_desc *desc; -+ u32 try_all_type; - - if (gpio >= hw->soc->npins) - return -EINVAL; -@@ -589,24 +590,39 @@ ssize_t mtk_pctrl_show_one_pin(struct mt - pinmux -= hw->soc->nfuncs; - - mtk_pinconf_bias_get_combo(hw, desc, &pullup, &pullen); -- if (pullen == MTK_PUPD_SET_R1R0_00) { -- pullen = 0; -- r1 = 0; -- r0 = 0; -- } else if (pullen == MTK_PUPD_SET_R1R0_01) { -- pullen = 1; -- r1 = 0; -- r0 = 1; -- } else if (pullen == MTK_PUPD_SET_R1R0_10) { -- pullen = 1; -- r1 = 1; -- r0 = 0; -- } else if (pullen == MTK_PUPD_SET_R1R0_11) { -+ -+ if (hw->soc->pull_type) -+ try_all_type = hw->soc->pull_type[desc->number]; -+ -+ if (hw->rsel_si_unit && (try_all_type & MTK_PULL_RSEL_TYPE)) { -+ rsel = pullen; - pullen = 1; -- r1 = 1; -- r0 = 1; -- } else if (pullen != MTK_DISABLE && pullen != MTK_ENABLE) { -- pullen = 0; -+ } else { -+ /* Case for: R1R0 */ -+ if (pullen == MTK_PUPD_SET_R1R0_00) { -+ pullen = 0; -+ r1 = 0; -+ r0 = 0; -+ } else if (pullen == MTK_PUPD_SET_R1R0_01) { -+ pullen = 1; -+ r1 = 0; -+ r0 = 1; -+ } else if (pullen == MTK_PUPD_SET_R1R0_10) { -+ pullen = 1; -+ r1 = 1; -+ r0 = 0; -+ } else if (pullen == MTK_PUPD_SET_R1R0_11) { -+ pullen = 1; -+ r1 = 1; -+ r0 = 1; -+ } -+ -+ /* Case for: RSEL */ -+ if (pullen >= MTK_PULL_SET_RSEL_000 && -+ pullen <= MTK_PULL_SET_RSEL_111) { -+ rsel = pullen - MTK_PULL_SET_RSEL_000; -+ pullen = 1; -+ } - } - len += scnprintf(buf + len, buf_len - len, - "%03d: %1d%1d%1d%1d%02d%1d%1d%1d%1d", -@@ -624,6 +640,8 @@ ssize_t mtk_pctrl_show_one_pin(struct mt - if (r1 != -1) { - len += scnprintf(buf + len, buf_len - len, " (%1d %1d)\n", - r1, r0); -+ } else if (rsel != -1) { -+ len += scnprintf(buf + len, buf_len - len, " (%1d)\n", rsel); - } else { - len += scnprintf(buf + len, buf_len - len, "\n"); - } -@@ -966,6 +984,12 @@ int mtk_paris_pinctrl_probe(struct platf - - hw->nbase = hw->soc->nbase_names; - -+ if (of_find_property(hw->dev->of_node, -+ "mediatek,rsel_resistance_in_si_unit", NULL)) -+ hw->rsel_si_unit = true; -+ else -+ hw->rsel_si_unit = false; -+ - spin_lock_init(&hw->lock); - - err = mtk_pctrl_build_state(pdev); diff --git a/target/linux/mediatek/patches-5.15/823-v5.17-pinctrl-mediatek-add-a-check-for-error-in-mtk_pincon.patch b/target/linux/mediatek/patches-5.15/823-v5.17-pinctrl-mediatek-add-a-check-for-error-in-mtk_pincon.patch deleted file mode 100644 index 6752b4093b..0000000000 --- a/target/linux/mediatek/patches-5.15/823-v5.17-pinctrl-mediatek-add-a-check-for-error-in-mtk_pincon.patch +++ /dev/null @@ -1,31 +0,0 @@ -From 9f9d17c228c89e38ed612500126daf626270be9a Mon Sep 17 00:00:00 2001 -From: Dan Carpenter -Date: Sat, 27 Nov 2021 17:08:36 +0300 -Subject: [PATCH] pinctrl: mediatek: add a check for error in - mtk_pinconf_bias_get_rsel() - -All the other mtk_hw_get_value() calls have a check for "if (err)" so -we can add one here as well. This silences a Smatch warning: - - drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c:819 mtk_pinconf_bias_get_rsel() - error: uninitialized symbol 'pd'. - -Fixes: fb34a9ae383a ("pinctrl: mediatek: support rsel feature") -Signed-off-by: Dan Carpenter -Link: https://lore.kernel.org/r/20211127140836.GB24002@kili -Signed-off-by: Linus Walleij ---- - drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c | 2 ++ - 1 file changed, 2 insertions(+) - ---- a/drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c -@@ -815,6 +815,8 @@ static int mtk_pinconf_bias_get_rsel(str - goto out; - - err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_PD, &pd); -+ if (err) -+ goto out; - - if (pu == 0 && pd == 0) { - *pullup = 0; diff --git a/target/linux/mediatek/patches-5.15/824-v6.1-pinctrl-mediatek-Fix-EINT-pins-input-debounce-time-c.patch b/target/linux/mediatek/patches-5.15/824-v6.1-pinctrl-mediatek-Fix-EINT-pins-input-debounce-time-c.patch deleted file mode 100644 index 47a29fbdba..0000000000 --- a/target/linux/mediatek/patches-5.15/824-v6.1-pinctrl-mediatek-Fix-EINT-pins-input-debounce-time-c.patch +++ /dev/null @@ -1,297 +0,0 @@ -From e1ff91f9d2303cd4e706cc908bfca21cd17b9927 Mon Sep 17 00:00:00 2001 -From: AngeloGioacchino Del Regno -Date: Fri, 11 Nov 2022 10:41:06 +0100 -Subject: [PATCH] pinctrl: mediatek: Fix EINT pins input debounce time - configuration - -The External Interrupt Controller (EINTC) on all of the supported -MediaTek SoCs does support input debouncing, but not all of them -index the debounce time values (DBNC_SETTING registers) the same way. - -Before this change, in some cases, as an example, requesting a debounce -time of 16 milliseconds would mistakenly set the relative DBNC_SETTING -register to 0x2, resulting in a way shorter debounce time of 500uS. - -To fix the aforementioned issue, define three different debounce_time -arrays, reflecting the correct register index for each value and for -each register index variant, and make sure that each SoC pinctrl -driver uses the right one. - -Signed-off-by: AngeloGioacchino Del Regno -Link: https://lore.kernel.org/r/20221111094106.18486-1-angelogioacchino.delregno@collabora.com -Signed-off-by: Linus Walleij ---- - drivers/pinctrl/mediatek/mtk-eint.c | 31 +++++++++++++++++++---- - drivers/pinctrl/mediatek/mtk-eint.h | 6 +++++ - drivers/pinctrl/mediatek/pinctrl-mt2701.c | 1 + - drivers/pinctrl/mediatek/pinctrl-mt2712.c | 1 + - drivers/pinctrl/mediatek/pinctrl-mt6765.c | 1 + - drivers/pinctrl/mediatek/pinctrl-mt6779.c | 1 + - drivers/pinctrl/mediatek/pinctrl-mt7622.c | 1 + - drivers/pinctrl/mediatek/pinctrl-mt7623.c | 1 + - drivers/pinctrl/mediatek/pinctrl-mt7629.c | 1 + - drivers/pinctrl/mediatek/pinctrl-mt8127.c | 1 + - drivers/pinctrl/mediatek/pinctrl-mt8135.c | 1 + - drivers/pinctrl/mediatek/pinctrl-mt8167.c | 1 + - drivers/pinctrl/mediatek/pinctrl-mt8173.c | 1 + - drivers/pinctrl/mediatek/pinctrl-mt8183.c | 1 + - drivers/pinctrl/mediatek/pinctrl-mt8192.c | 1 + - drivers/pinctrl/mediatek/pinctrl-mt8195.c | 1 + - drivers/pinctrl/mediatek/pinctrl-mt8365.c | 1 + - drivers/pinctrl/mediatek/pinctrl-mt8516.c | 1 + - 22 files changed, 53 insertions(+), 5 deletions(-) - ---- a/drivers/pinctrl/mediatek/mtk-eint.c -+++ b/drivers/pinctrl/mediatek/mtk-eint.c -@@ -24,6 +24,7 @@ - #define MTK_EINT_EDGE_SENSITIVE 0 - #define MTK_EINT_LEVEL_SENSITIVE 1 - #define MTK_EINT_DBNC_SET_DBNC_BITS 4 -+#define MTK_EINT_DBNC_MAX 16 - #define MTK_EINT_DBNC_RST_BIT (0x1 << 1) - #define MTK_EINT_DBNC_SET_EN (0x1 << 0) - -@@ -48,6 +49,18 @@ static const struct mtk_eint_regs mtk_ge - .dbnc_clr = 0x700, - }; - -+const unsigned int debounce_time_mt2701[] = { -+ 500, 1000, 16000, 32000, 64000, 128000, 256000, 0 -+}; -+ -+const unsigned int debounce_time_mt6765[] = { -+ 125, 250, 500, 1000, 16000, 32000, 64000, 128000, 256000, 512000, 0 -+}; -+ -+const unsigned int debounce_time_mt6795[] = { -+ 500, 1000, 16000, 32000, 64000, 128000, 256000, 512000, 0 -+}; -+ - static void __iomem *mtk_eint_get_offset(struct mtk_eint *eint, - unsigned int eint_num, - unsigned int offset) -@@ -407,10 +420,11 @@ int mtk_eint_set_debounce(struct mtk_ein - int virq, eint_offset; - unsigned int set_offset, bit, clr_bit, clr_offset, rst, i, unmask, - dbnc; -- static const unsigned int debounce_time[] = {500, 1000, 16000, 32000, -- 64000, 128000, 256000}; - struct irq_data *d; - -+ if (!eint->hw->db_time) -+ return -EOPNOTSUPP; -+ - virq = irq_find_mapping(eint->domain, eint_num); - eint_offset = (eint_num % 4) * 8; - d = irq_get_irq_data(virq); -@@ -421,9 +435,9 @@ int mtk_eint_set_debounce(struct mtk_ein - if (!mtk_eint_can_en_debounce(eint, eint_num)) - return -EINVAL; - -- dbnc = ARRAY_SIZE(debounce_time); -- for (i = 0; i < ARRAY_SIZE(debounce_time); i++) { -- if (debounce <= debounce_time[i]) { -+ dbnc = eint->num_db_time; -+ for (i = 0; i < eint->num_db_time; i++) { -+ if (debounce <= eint->hw->db_time[i]) { - dbnc = i; - break; - } -@@ -497,6 +511,13 @@ int mtk_eint_do_init(struct mtk_eint *ei - if (!eint->domain) - return -ENOMEM; - -+ if (eint->hw->db_time) { -+ for (i = 0; i < MTK_EINT_DBNC_MAX; i++) -+ if (eint->hw->db_time[i] == 0) -+ break; -+ eint->num_db_time = i; -+ } -+ - mtk_eint_hw_init(eint); - for (i = 0; i < eint->hw->ap_num; i++) { - int virq = irq_create_mapping(eint->domain, i); ---- a/drivers/pinctrl/mediatek/mtk-eint.h -+++ b/drivers/pinctrl/mediatek/mtk-eint.h -@@ -37,8 +37,13 @@ struct mtk_eint_hw { - u8 ports; - unsigned int ap_num; - unsigned int db_cnt; -+ const unsigned int *db_time; - }; - -+extern const unsigned int debounce_time_mt2701[]; -+extern const unsigned int debounce_time_mt6765[]; -+extern const unsigned int debounce_time_mt6795[]; -+ - struct mtk_eint; - - struct mtk_eint_xt { -@@ -62,6 +67,7 @@ struct mtk_eint { - /* Used to fit into various EINT device */ - const struct mtk_eint_hw *hw; - const struct mtk_eint_regs *regs; -+ u16 num_db_time; - - /* Used to fit into various pinctrl device */ - void *pctl; ---- a/drivers/pinctrl/mediatek/pinctrl-mt2701.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mt2701.c -@@ -531,6 +531,7 @@ static const struct mtk_pinctrl_devdata - .ports = 6, - .ap_num = 169, - .db_cnt = 16, -+ .db_time = debounce_time_mt2701, - }, - }; - ---- a/drivers/pinctrl/mediatek/pinctrl-mt2712.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mt2712.c -@@ -584,6 +584,7 @@ static const struct mtk_pinctrl_devdata - .ports = 8, - .ap_num = 229, - .db_cnt = 40, -+ .db_time = debounce_time_mt2701, - }, - }; - ---- a/drivers/pinctrl/mediatek/pinctrl-mt6765.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mt6765.c -@@ -1062,6 +1062,7 @@ static const struct mtk_eint_hw mt6765_e - .ports = 6, - .ap_num = 160, - .db_cnt = 13, -+ .db_time = debounce_time_mt6765, - }; - - static const struct mtk_pin_soc mt6765_data = { ---- a/drivers/pinctrl/mediatek/pinctrl-mt6779.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mt6779.c -@@ -737,6 +737,7 @@ static const struct mtk_eint_hw mt6779_e - .ports = 6, - .ap_num = 195, - .db_cnt = 13, -+ .db_time = debounce_time_mt2701, - }; - - static const struct mtk_pin_soc mt6779_data = { ---- a/drivers/pinctrl/mediatek/pinctrl-mt7622.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mt7622.c -@@ -846,6 +846,7 @@ static const struct mtk_eint_hw mt7622_e - .ports = 7, - .ap_num = ARRAY_SIZE(mt7622_pins), - .db_cnt = 20, -+ .db_time = debounce_time_mt6765, - }; - - static const struct mtk_pin_soc mt7622_data = { ---- a/drivers/pinctrl/mediatek/pinctrl-mt7623.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mt7623.c -@@ -1369,6 +1369,7 @@ static const struct mtk_eint_hw mt7623_e - .ports = 6, - .ap_num = 169, - .db_cnt = 20, -+ .db_time = debounce_time_mt2701, - }; - - static struct mtk_pin_soc mt7623_data = { ---- a/drivers/pinctrl/mediatek/pinctrl-mt7629.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mt7629.c -@@ -402,6 +402,7 @@ static const struct mtk_eint_hw mt7629_e - .ports = 7, - .ap_num = ARRAY_SIZE(mt7629_pins), - .db_cnt = 16, -+ .db_time = debounce_time_mt2701, - }; - - static struct mtk_pin_soc mt7629_data = { ---- a/drivers/pinctrl/mediatek/pinctrl-mt8127.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mt8127.c -@@ -300,6 +300,7 @@ static const struct mtk_pinctrl_devdata - .ports = 6, - .ap_num = 143, - .db_cnt = 16, -+ .db_time = debounce_time_mt2701, - }, - }; - ---- a/drivers/pinctrl/mediatek/pinctrl-mt8135.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mt8135.c -@@ -313,6 +313,7 @@ static const struct mtk_pinctrl_devdata - .ports = 6, - .ap_num = 192, - .db_cnt = 16, -+ .db_time = debounce_time_mt2701, - }, - }; - ---- a/drivers/pinctrl/mediatek/pinctrl-mt8167.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mt8167.c -@@ -332,6 +332,7 @@ static const struct mtk_pinctrl_devdata - .ports = 6, - .ap_num = 169, - .db_cnt = 64, -+ .db_time = debounce_time_mt6795, - }, - }; - ---- a/drivers/pinctrl/mediatek/pinctrl-mt8173.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mt8173.c -@@ -340,6 +340,7 @@ static const struct mtk_pinctrl_devdata - .ports = 6, - .ap_num = 224, - .db_cnt = 16, -+ .db_time = debounce_time_mt2701, - }, - }; - ---- a/drivers/pinctrl/mediatek/pinctrl-mt8183.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mt8183.c -@@ -545,6 +545,7 @@ static const struct mtk_eint_hw mt8183_e - .ports = 6, - .ap_num = 212, - .db_cnt = 13, -+ .db_time = debounce_time_mt6765, - }; - - static const struct mtk_pin_soc mt8183_data = { ---- a/drivers/pinctrl/mediatek/pinctrl-mt8192.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mt8192.c -@@ -1339,6 +1339,7 @@ static const struct mtk_eint_hw mt8192_e - .ports = 7, - .ap_num = 224, - .db_cnt = 32, -+ .db_time = debounce_time_mt6765, - }; - - static const struct mtk_pin_reg_calc mt8192_reg_cals[PINCTRL_PIN_REG_MAX] = { ---- a/drivers/pinctrl/mediatek/pinctrl-mt8195.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mt8195.c -@@ -805,6 +805,7 @@ static const struct mtk_eint_hw mt8195_e - .ports = 7, - .ap_num = 225, - .db_cnt = 32, -+ .db_time = debounce_time_mt6765, - }; - - static const struct mtk_pin_soc mt8195_data = { ---- a/drivers/pinctrl/mediatek/pinctrl-mt8365.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mt8365.c -@@ -466,6 +466,7 @@ static const struct mtk_pinctrl_devdata - .ports = 5, - .ap_num = 160, - .db_cnt = 160, -+ .db_time = debounce_time_mt6765, - }, - }; - ---- a/drivers/pinctrl/mediatek/pinctrl-mt8516.c -+++ b/drivers/pinctrl/mediatek/pinctrl-mt8516.c -@@ -332,6 +332,7 @@ static const struct mtk_pinctrl_devdata - .ports = 6, - .ap_num = 169, - .db_cnt = 64, -+ .db_time = debounce_time_mt6795, - }, - }; - diff --git a/target/linux/mediatek/patches-5.15/825-v6.1-pinctrl-mediatek-Export-debounce-time-tables.patch b/target/linux/mediatek/patches-5.15/825-v6.1-pinctrl-mediatek-Export-debounce-time-tables.patch deleted file mode 100644 index 92f4e842e8..0000000000 --- a/target/linux/mediatek/patches-5.15/825-v6.1-pinctrl-mediatek-Export-debounce-time-tables.patch +++ /dev/null @@ -1,37 +0,0 @@ -From 2e35b25dd8e666b8619355fc3defb1b246a5dc02 Mon Sep 17 00:00:00 2001 -From: Linus Walleij -Date: Tue, 15 Nov 2022 09:11:07 +0100 -Subject: [PATCH] pinctrl: mediatek: Export debounce time tables - -The kernel test robot complains that in certain combinations -when building the Mediatek drivers as modules we lack some -debounce table symbols, so export them. - -Reported-by: kernel test robot -Fixes: e1ff91f9d230 ("pinctrl: mediatek: Fix EINT pins input debounce time configuration") -Cc: AngeloGioacchino Del Regno -Signed-off-by: Linus Walleij ---- - drivers/pinctrl/mediatek/mtk-eint.c | 3 +++ - 1 file changed, 3 insertions(+) - ---- a/drivers/pinctrl/mediatek/mtk-eint.c -+++ b/drivers/pinctrl/mediatek/mtk-eint.c -@@ -52,14 +52,17 @@ static const struct mtk_eint_regs mtk_ge - const unsigned int debounce_time_mt2701[] = { - 500, 1000, 16000, 32000, 64000, 128000, 256000, 0 - }; -+EXPORT_SYMBOL_GPL(debounce_time_mt2701); - - const unsigned int debounce_time_mt6765[] = { - 125, 250, 500, 1000, 16000, 32000, 64000, 128000, 256000, 512000, 0 - }; -+EXPORT_SYMBOL_GPL(debounce_time_mt6765); - - const unsigned int debounce_time_mt6795[] = { - 500, 1000, 16000, 32000, 64000, 128000, 256000, 512000, 0 - }; -+EXPORT_SYMBOL_GPL(debounce_time_mt6795); - - static void __iomem *mtk_eint_get_offset(struct mtk_eint *eint, - unsigned int eint_num, diff --git a/target/linux/mediatek/patches-5.15/826-v6.2-pinctrl-mediatek-extend-pinctrl-moore-to-support-new.patch b/target/linux/mediatek/patches-5.15/826-v6.2-pinctrl-mediatek-extend-pinctrl-moore-to-support-new.patch deleted file mode 100644 index f130fdbc56..0000000000 --- a/target/linux/mediatek/patches-5.15/826-v6.2-pinctrl-mediatek-extend-pinctrl-moore-to-support-new.patch +++ /dev/null @@ -1,129 +0,0 @@ -From fae82621ac33e2a4a96220c56e90d1ec6237d394 Mon Sep 17 00:00:00 2001 -From: Sam Shih -Date: Sun, 6 Nov 2022 09:01:12 +0100 -Subject: [PATCH] pinctrl: mediatek: extend pinctrl-moore to support new bias - functions - -Commit fb34a9ae383a ("pinctrl: mediatek: support rsel feature") -introduced SoC specify 'pull_type' attribute to mtk_pinconf_bias_set_combo -and mtk_pinconf_bias_get_combo, and make the functions able to support -almost all Mediatek SoCs that use pinctrl-mtk-common-v2.c. - -This patch enables pinctrl_moore to support these functions. - -Signed-off-by: Sam Shih -Signed-off-by: Frank Wunderlich -Reviewed-by: AngeloGioacchino Del Regno -Link: https://lore.kernel.org/r/20221106080114.7426-6-linux@fw-web.de -Signed-off-by: Linus Walleij ---- - drivers/pinctrl/mediatek/pinctrl-moore.c | 49 ++++++++++++++++++++---- - 1 file changed, 42 insertions(+), 7 deletions(-) - ---- a/drivers/pinctrl/mediatek/pinctrl-moore.c -+++ b/drivers/pinctrl/mediatek/pinctrl-moore.c -@@ -8,6 +8,7 @@ - * - */ - -+#include - #include - #include "pinctrl-moore.h" - -@@ -105,7 +106,7 @@ static int mtk_pinconf_get(struct pinctr - { - struct mtk_pinctrl *hw = pinctrl_dev_get_drvdata(pctldev); - u32 param = pinconf_to_config_param(*config); -- int val, val2, err, reg, ret = 1; -+ int val, val2, err, pullup, reg, ret = 1; - const struct mtk_pin_desc *desc; - - desc = (const struct mtk_pin_desc *)&hw->soc->pins[pin]; -@@ -114,7 +115,13 @@ static int mtk_pinconf_get(struct pinctr - - switch (param) { - case PIN_CONFIG_BIAS_DISABLE: -- if (hw->soc->bias_disable_get) { -+ if (hw->soc->bias_get_combo) { -+ err = hw->soc->bias_get_combo(hw, desc, &pullup, &ret); -+ if (err) -+ return err; -+ if (ret != MTK_PUPD_SET_R1R0_00 && ret != MTK_DISABLE) -+ return -EINVAL; -+ } else if (hw->soc->bias_disable_get) { - err = hw->soc->bias_disable_get(hw, desc, &ret); - if (err) - return err; -@@ -123,7 +130,15 @@ static int mtk_pinconf_get(struct pinctr - } - break; - case PIN_CONFIG_BIAS_PULL_UP: -- if (hw->soc->bias_get) { -+ if (hw->soc->bias_get_combo) { -+ err = hw->soc->bias_get_combo(hw, desc, &pullup, &ret); -+ if (err) -+ return err; -+ if (ret == MTK_PUPD_SET_R1R0_00 || ret == MTK_DISABLE) -+ return -EINVAL; -+ if (!pullup) -+ return -EINVAL; -+ } else if (hw->soc->bias_get) { - err = hw->soc->bias_get(hw, desc, 1, &ret); - if (err) - return err; -@@ -132,7 +147,15 @@ static int mtk_pinconf_get(struct pinctr - } - break; - case PIN_CONFIG_BIAS_PULL_DOWN: -- if (hw->soc->bias_get) { -+ if (hw->soc->bias_get_combo) { -+ err = hw->soc->bias_get_combo(hw, desc, &pullup, &ret); -+ if (err) -+ return err; -+ if (ret == MTK_PUPD_SET_R1R0_00 || ret == MTK_DISABLE) -+ return -EINVAL; -+ if (pullup) -+ return -EINVAL; -+ } else if (hw->soc->bias_get) { - err = hw->soc->bias_get(hw, desc, 0, &ret); - if (err) - return err; -@@ -235,7 +258,11 @@ static int mtk_pinconf_set(struct pinctr - - switch (param) { - case PIN_CONFIG_BIAS_DISABLE: -- if (hw->soc->bias_disable_set) { -+ if (hw->soc->bias_set_combo) { -+ err = hw->soc->bias_set_combo(hw, desc, 0, MTK_DISABLE); -+ if (err) -+ return err; -+ } else if (hw->soc->bias_disable_set) { - err = hw->soc->bias_disable_set(hw, desc); - if (err) - return err; -@@ -244,7 +271,11 @@ static int mtk_pinconf_set(struct pinctr - } - break; - case PIN_CONFIG_BIAS_PULL_UP: -- if (hw->soc->bias_set) { -+ if (hw->soc->bias_set_combo) { -+ err = hw->soc->bias_set_combo(hw, desc, 1, arg); -+ if (err) -+ return err; -+ } else if (hw->soc->bias_set) { - err = hw->soc->bias_set(hw, desc, 1); - if (err) - return err; -@@ -253,7 +284,11 @@ static int mtk_pinconf_set(struct pinctr - } - break; - case PIN_CONFIG_BIAS_PULL_DOWN: -- if (hw->soc->bias_set) { -+ if (hw->soc->bias_set_combo) { -+ err = hw->soc->bias_set_combo(hw, desc, 0, arg); -+ if (err) -+ return err; -+ } else if (hw->soc->bias_set) { - err = hw->soc->bias_set(hw, desc, 0); - if (err) - return err; diff --git a/target/linux/mediatek/patches-5.15/830-v5.18-regulator-Add-bindings-for-Richtek-RT5190A-PMIC.patch b/target/linux/mediatek/patches-5.15/830-v5.18-regulator-Add-bindings-for-Richtek-RT5190A-PMIC.patch deleted file mode 100644 index 30891d3487..0000000000 --- a/target/linux/mediatek/patches-5.15/830-v5.18-regulator-Add-bindings-for-Richtek-RT5190A-PMIC.patch +++ /dev/null @@ -1,180 +0,0 @@ -From b77e70f6b8f2cc62fba847f3008a430a09ef275d Mon Sep 17 00:00:00 2001 -From: ChiYuan Huang -Date: Wed, 9 Mar 2022 16:01:42 +0800 -Subject: [PATCH 1/2] regulator: Add bindings for Richtek RT5190A PMIC - -Add bindings for Richtek RT5190A PMIC. - -Signed-off-by: ChiYuan Huang -Reviewed-by: Krzysztof Kozlowski -Link: https://lore.kernel.org/r/1646812903-32496-2-git-send-email-u0084500@gmail.com -Signed-off-by: Mark Brown ---- - .../regulator/richtek,rt5190a-regulator.yaml | 141 ++++++++++++++++++ - .../regulator/richtek,rt5190a-regulator.h | 15 ++ - 2 files changed, 156 insertions(+) - create mode 100644 Documentation/devicetree/bindings/regulator/richtek,rt5190a-regulator.yaml - create mode 100644 include/dt-bindings/regulator/richtek,rt5190a-regulator.h - ---- /dev/null -+++ b/Documentation/devicetree/bindings/regulator/richtek,rt5190a-regulator.yaml -@@ -0,0 +1,141 @@ -+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause -+%YAML 1.2 -+--- -+$id: http://devicetree.org/schemas/regulator/richtek,rt5190a-regulator.yaml# -+$schema: http://devicetree.org/meta-schemas/core.yaml# -+ -+title: Richtek RT5190A PMIC Regulator -+ -+maintainers: -+ - ChiYuan Huang -+ -+description: | -+ The RT5190A integrates 1 channel buck controller, 3 channels high efficiency -+ synchronous buck converters, 1 LDO, I2C control interface and peripherial -+ logical control. -+ -+ It also supports mute AC OFF depop sound and quick setting storage while -+ input power is removed. -+ -+properties: -+ compatible: -+ enum: -+ - richtek,rt5190a -+ -+ reg: -+ maxItems: 1 -+ -+ interrupts: -+ maxItems: 1 -+ -+ vin2-supply: -+ description: phandle to buck2 input voltage. -+ -+ vin3-supply: -+ description: phandle to buck3 input voltage. -+ -+ vin4-supply: -+ description: phandle to buck4 input voltage. -+ -+ vinldo-supply: -+ description: phandle to ldo input voltage -+ -+ richtek,mute-enable: -+ description: | -+ The mute function uses 'mutein', 'muteout', and 'vdet' pins as the control -+ signal. When enabled, The normal behavior is to bypass the 'mutein' signal -+ 'muteout'. But if the power source removal is detected from 'vdet', -+ whatever the 'mutein' signal is, it will pull down the 'muteout' to force -+ speakers mute. this function is commonly used to prevent the speaker pop -+ noise during AC power turned off in the modern TV system design. -+ type: boolean -+ -+ regulators: -+ type: object -+ -+ patternProperties: -+ "^buck[1-4]$|^ldo$": -+ type: object -+ $ref: regulator.yaml# -+ description: | -+ regulator description for buck1 and buck4. -+ -+ properties: -+ regulator-allowed-modes: -+ description: | -+ buck operating mode, only buck1/4 support mode operating. -+ 0: auto mode -+ 1: force pwm mode -+ items: -+ enum: [0, 1] -+ -+ richtek,latchup-enable: -+ type: boolean -+ description: | -+ If specified, undervolt protection mode changes from the default -+ hiccup to latchup. -+ -+ unevaluatedProperties: false -+ -+ additionalProperties: false -+ -+required: -+ - compatible -+ - reg -+ - regulators -+ -+additionalProperties: false -+ -+examples: -+ - | -+ #include -+ #include -+ -+ i2c { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ pmic@64 { -+ compatible = "richtek,rt5190a"; -+ reg = <0x64>; -+ interrupts-extended = <&gpio26 0 IRQ_TYPE_LEVEL_LOW>; -+ vin2-supply = <&rt5190_buck1>; -+ vin3-supply = <&rt5190_buck1>; -+ vin4-supply = <&rt5190_buck1>; -+ -+ regulators { -+ rt5190_buck1: buck1 { -+ regulator-name = "rt5190a-buck1"; -+ regulator-min-microvolt = <5090000>; -+ regulator-max-microvolt = <5090000>; -+ regulator-allowed-modes = ; -+ regulator-boot-on; -+ }; -+ buck2 { -+ regulator-name = "rt5190a-buck2"; -+ regulator-min-microvolt = <600000>; -+ regulator-max-microvolt = <1400000>; -+ regulator-boot-on; -+ }; -+ buck3 { -+ regulator-name = "rt5190a-buck3"; -+ regulator-min-microvolt = <600000>; -+ regulator-max-microvolt = <1400000>; -+ regulator-boot-on; -+ }; -+ buck4 { -+ regulator-name = "rt5190a-buck4"; -+ regulator-min-microvolt = <850000>; -+ regulator-max-microvolt = <850000>; -+ regulator-allowed-modes = ; -+ regulator-boot-on; -+ }; -+ ldo { -+ regulator-name = "rt5190a-ldo"; -+ regulator-min-microvolt = <1200000>; -+ regulator-max-microvolt = <1200000>; -+ regulator-boot-on; -+ }; -+ }; -+ }; -+ }; ---- /dev/null -+++ b/include/dt-bindings/regulator/richtek,rt5190a-regulator.h -@@ -0,0 +1,15 @@ -+/* SPDX-License-Identifier: GPL-2.0 */ -+ -+#ifndef __DT_BINDINGS_RICHTEK_RT5190A_REGULATOR_H__ -+#define __DT_BINDINGS_RICHTEK_RT5190A_REGULATOR_H__ -+ -+/* -+ * BUCK/LDO mode constants which may be used in devicetree properties -+ * (eg. regulator-allowed-modes). -+ * See the manufacturer's datasheet for more information on these modes. -+ */ -+ -+#define RT5190A_OPMODE_AUTO 0 -+#define RT5190A_OPMODE_FPWM 1 -+ -+#endif diff --git a/target/linux/mediatek/patches-5.15/831-v5.18-regulator-rt5190a-Add-support-for-Richtek-RT5190A-PM.patch b/target/linux/mediatek/patches-5.15/831-v5.18-regulator-rt5190a-Add-support-for-Richtek-RT5190A-PM.patch deleted file mode 100644 index 0e0f099e50..0000000000 --- a/target/linux/mediatek/patches-5.15/831-v5.18-regulator-rt5190a-Add-support-for-Richtek-RT5190A-PM.patch +++ /dev/null @@ -1,562 +0,0 @@ -From 760423dfad53877b468490758fe7ea968ded9402 Mon Sep 17 00:00:00 2001 -From: ChiYuan Huang -Date: Wed, 9 Mar 2022 16:01:43 +0800 -Subject: [PATCH 2/2] regulator: rt5190a: Add support for Richtek RT5190A PMIC - -Add support for Richtek RT5190A PMIC. - -Signed-off-by: ChiYuan Huang -Link: https://lore.kernel.org/r/1646812903-32496-3-git-send-email-u0084500@gmail.com -Signed-off-by: Mark Brown ---- - drivers/regulator/Kconfig | 10 + - drivers/regulator/Makefile | 1 + - drivers/regulator/rt5190a-regulator.c | 513 ++++++++++++++++++++++++++ - 3 files changed, 524 insertions(+) - create mode 100644 drivers/regulator/rt5190a-regulator.c - ---- a/drivers/regulator/Kconfig -+++ b/drivers/regulator/Kconfig -@@ -1037,6 +1037,16 @@ config REGULATOR_RT5033 - RT5033 PMIC. The device supports multiple regulators like - current source, LDO and Buck. - -+config REGULATOR_RT5190A -+ tristate "Richtek RT5190A PMIC" -+ depends on I2C -+ select REGMAP_I2C -+ help -+ This adds support for voltage regulator in Richtek RT5190A PMIC. -+ It integratas 1 channel buck controller, 3 channels high efficiency -+ buck converters, 1 LDO, mute AC OFF depop function, with the general -+ I2C control interface. -+ - config REGULATOR_RT6160 - tristate "Richtek RT6160 BuckBoost voltage regulator" - depends on I2C ---- a/drivers/regulator/Makefile -+++ b/drivers/regulator/Makefile -@@ -125,6 +125,7 @@ obj-$(CONFIG_REGULATOR_ROHM) += rohm-reg - obj-$(CONFIG_REGULATOR_RT4801) += rt4801-regulator.o - obj-$(CONFIG_REGULATOR_RT4831) += rt4831-regulator.o - obj-$(CONFIG_REGULATOR_RT5033) += rt5033-regulator.o -+obj-$(CONFIG_REGULATOR_RT5190A) += rt5190a-regulator.o - obj-$(CONFIG_REGULATOR_RT6160) += rt6160-regulator.o - obj-$(CONFIG_REGULATOR_RT6245) += rt6245-regulator.o - obj-$(CONFIG_REGULATOR_RTMV20) += rtmv20-regulator.o ---- /dev/null -+++ b/drivers/regulator/rt5190a-regulator.c -@@ -0,0 +1,513 @@ -+// SPDX-License-Identifier: GPL-2.0+ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#define RT5190A_REG_MANUFACTURE 0x00 -+#define RT5190A_REG_BUCK2VSEL 0x04 -+#define RT5190A_REG_BUCK3VSEL 0x05 -+#define RT5190A_REG_DCDCCNTL 0x06 -+#define RT5190A_REG_ENABLE 0x07 -+#define RT5190A_REG_DISCHARGE 0x09 -+#define RT5190A_REG_PROTMODE 0x0A -+#define RT5190A_REG_MUTECNTL 0x0B -+#define RT5190A_REG_PGSTAT 0x0F -+#define RT5190A_REG_OVINT 0x10 -+#define RT5190A_REG_HOTDIEMASK 0x17 -+ -+#define RT5190A_VSEL_MASK GENMASK(6, 0) -+#define RT5190A_RID_BITMASK(rid) BIT(rid + 1) -+#define RT5190A_BUCK1_DISCHG_MASK GENMASK(1, 0) -+#define RT5190A_BUCK1_DISCHG_ONVAL 0x01 -+#define RT5190A_OVERVOLT_MASK GENMASK(7, 0) -+#define RT5190A_UNDERVOLT_MASK GENMASK(15, 8) -+#define RT5190A_CH234OT_MASK BIT(29) -+#define RT5190A_CHIPOT_MASK BIT(28) -+ -+#define RT5190A_BUCK23_MINUV 600000 -+#define RT5190A_BUCK23_MAXUV 1400000 -+#define RT5190A_BUCK23_STEPUV 10000 -+#define RT5190A_BUCK23_STEPNUM ((1400000 - 600000) / 10000 + 1) -+ -+enum { -+ RT5190A_IDX_BUCK1 = 0, -+ RT5190A_IDX_BUCK2, -+ RT5190A_IDX_BUCK3, -+ RT5190A_IDX_BUCK4, -+ RT5190A_IDX_LDO, -+ RT5190A_MAX_IDX -+}; -+ -+struct rt5190a_priv { -+ struct device *dev; -+ struct regmap *regmap; -+ struct regulator_desc rdesc[RT5190A_MAX_IDX]; -+ struct regulator_dev *rdev[RT5190A_MAX_IDX]; -+}; -+ -+static int rt5190a_get_error_flags(struct regulator_dev *rdev, -+ unsigned int *flags) -+{ -+ struct regmap *regmap = rdev_get_regmap(rdev); -+ int rid = rdev_get_id(rdev); -+ unsigned int pgood_stat; -+ int ret; -+ -+ ret = regmap_read(regmap, RT5190A_REG_PGSTAT, &pgood_stat); -+ if (ret) -+ return ret; -+ -+ if (!(pgood_stat & RT5190A_RID_BITMASK(rid))) -+ *flags = REGULATOR_ERROR_FAIL; -+ else -+ *flags = 0; -+ -+ return 0; -+} -+ -+static int rt5190a_fixed_buck_set_mode(struct regulator_dev *rdev, -+ unsigned int mode) -+{ -+ struct regmap *regmap = rdev_get_regmap(rdev); -+ int rid = rdev_get_id(rdev); -+ unsigned int mask = RT5190A_RID_BITMASK(rid), val; -+ -+ switch (mode) { -+ case REGULATOR_MODE_FAST: -+ val = mask; -+ break; -+ case REGULATOR_MODE_NORMAL: -+ val = 0; -+ break; -+ default: -+ return -EINVAL; -+ } -+ -+ return regmap_update_bits(regmap, RT5190A_REG_DCDCCNTL, mask, val); -+} -+ -+static unsigned int rt5190a_fixed_buck_get_mode(struct regulator_dev *rdev) -+{ -+ struct regmap *regmap = rdev_get_regmap(rdev); -+ int rid = rdev_get_id(rdev); -+ unsigned int val; -+ int ret; -+ -+ ret = regmap_read(regmap, RT5190A_REG_DCDCCNTL, &val); -+ if (ret) { -+ dev_err(&rdev->dev, "Failed to get mode [%d]\n", ret); -+ return ret; -+ } -+ -+ if (val & RT5190A_RID_BITMASK(rid)) -+ return REGULATOR_MODE_FAST; -+ -+ return REGULATOR_MODE_NORMAL; -+} -+ -+static const struct regulator_ops rt5190a_ranged_buck_ops = { -+ .enable = regulator_enable_regmap, -+ .disable = regulator_disable_regmap, -+ .is_enabled = regulator_is_enabled_regmap, -+ .set_voltage_sel = regulator_set_voltage_sel_regmap, -+ .get_voltage_sel = regulator_get_voltage_sel_regmap, -+ .list_voltage = regulator_list_voltage_linear, -+ .set_active_discharge = regulator_set_active_discharge_regmap, -+ .get_error_flags = rt5190a_get_error_flags, -+}; -+ -+static const struct regulator_ops rt5190a_fixed_buck_ops = { -+ .enable = regulator_enable_regmap, -+ .disable = regulator_disable_regmap, -+ .is_enabled = regulator_is_enabled_regmap, -+ .set_active_discharge = regulator_set_active_discharge_regmap, -+ .set_mode = rt5190a_fixed_buck_set_mode, -+ .get_mode = rt5190a_fixed_buck_get_mode, -+ .get_error_flags = rt5190a_get_error_flags, -+}; -+ -+static const struct regulator_ops rt5190a_fixed_ldo_ops = { -+ .enable = regulator_enable_regmap, -+ .disable = regulator_disable_regmap, -+ .is_enabled = regulator_is_enabled_regmap, -+ .set_active_discharge = regulator_set_active_discharge_regmap, -+ .get_error_flags = rt5190a_get_error_flags, -+}; -+ -+static irqreturn_t rt5190a_irq_handler(int irq, void *data) -+{ -+ struct rt5190a_priv *priv = data; -+ __le32 raws; -+ unsigned int events, fields; -+ static const struct { -+ unsigned int bitmask; -+ unsigned int report; -+ } event_tbl[] = { -+ { RT5190A_OVERVOLT_MASK, REGULATOR_ERROR_REGULATION_OUT }, -+ { RT5190A_UNDERVOLT_MASK, REGULATOR_ERROR_UNDER_VOLTAGE } -+ }; -+ int i, j, ret; -+ -+ ret = regmap_raw_read(priv->regmap, RT5190A_REG_OVINT, &raws, -+ sizeof(raws)); -+ if (ret) { -+ dev_err(priv->dev, "Failed to read events\n"); -+ return IRQ_NONE; -+ } -+ -+ events = le32_to_cpu(raws); -+ -+ ret = regmap_raw_write(priv->regmap, RT5190A_REG_OVINT, &raws, -+ sizeof(raws)); -+ if (ret) -+ dev_err(priv->dev, "Failed to write-clear events\n"); -+ -+ /* Handle OV,UV events */ -+ for (i = 0; i < ARRAY_SIZE(event_tbl); i++) { -+ fields = events & event_tbl[i].bitmask; -+ fields >>= ffs(event_tbl[i].bitmask) - 1; -+ -+ for (j = 0; j < RT5190A_MAX_IDX; j++) { -+ if (!(fields & RT5190A_RID_BITMASK(j))) -+ continue; -+ -+ regulator_notifier_call_chain(priv->rdev[j], -+ event_tbl[i].report, -+ NULL); -+ } -+ } -+ -+ /* Handle CH234 OT event */ -+ if (events & RT5190A_CH234OT_MASK) { -+ for (j = RT5190A_IDX_BUCK2; j < RT5190A_IDX_LDO; j++) { -+ regulator_notifier_call_chain(priv->rdev[j], -+ REGULATOR_ERROR_OVER_TEMP, -+ NULL); -+ } -+ } -+ -+ /* Warning if CHIP OT occur */ -+ if (events & RT5190A_CHIPOT_MASK) -+ dev_warn(priv->dev, "CHIP overheat\n"); -+ -+ return IRQ_HANDLED; -+} -+ -+static unsigned int rt5190a_of_map_mode(unsigned int mode) -+{ -+ switch (mode) { -+ case RT5190A_OPMODE_AUTO: -+ return REGULATOR_MODE_NORMAL; -+ case RT5190A_OPMODE_FPWM: -+ return REGULATOR_MODE_FAST; -+ default: -+ return REGULATOR_MODE_INVALID; -+ } -+} -+ -+static int rt5190a_of_parse_cb(struct rt5190a_priv *priv, int rid, -+ struct of_regulator_match *match) -+{ -+ struct regulator_desc *desc = priv->rdesc + rid; -+ struct regulator_init_data *init_data = match->init_data; -+ struct device_node *np = match->of_node; -+ bool latchup_enable; -+ unsigned int mask = RT5190A_RID_BITMASK(rid), val; -+ -+ switch (rid) { -+ case RT5190A_IDX_BUCK1: -+ case RT5190A_IDX_BUCK4: -+ case RT5190A_IDX_LDO: -+ init_data->constraints.apply_uV = 0; -+ -+ if (init_data->constraints.min_uV == -+ init_data->constraints.max_uV) -+ desc->fixed_uV = init_data->constraints.min_uV; -+ else { -+ dev_err(priv->dev, -+ "Variable voltage for fixed regulator\n"); -+ return -EINVAL; -+ } -+ break; -+ default: -+ break; -+ } -+ -+ latchup_enable = of_property_read_bool(np, "richtek,latchup-enable"); -+ -+ /* latchup: 0, default hiccup: 1 */ -+ val = !latchup_enable ? mask : 0; -+ -+ return regmap_update_bits(priv->regmap, RT5190A_REG_PROTMODE, mask, val); -+} -+ -+static void rt5190a_fillin_regulator_desc(struct regulator_desc *desc, int rid) -+{ -+ static const char * const regu_name[] = { "buck1", "buck2", -+ "buck3", "buck4", -+ "ldo" }; -+ static const char * const supply[] = { NULL, "vin2", "vin3", "vin4", -+ "vinldo" }; -+ -+ desc->name = regu_name[rid]; -+ desc->supply_name = supply[rid]; -+ desc->owner = THIS_MODULE; -+ desc->type = REGULATOR_VOLTAGE; -+ desc->id = rid; -+ desc->enable_reg = RT5190A_REG_ENABLE; -+ desc->enable_mask = RT5190A_RID_BITMASK(rid); -+ desc->active_discharge_reg = RT5190A_REG_DISCHARGE; -+ desc->active_discharge_mask = RT5190A_RID_BITMASK(rid); -+ desc->active_discharge_on = RT5190A_RID_BITMASK(rid); -+ -+ switch (rid) { -+ case RT5190A_IDX_BUCK1: -+ desc->active_discharge_mask = RT5190A_BUCK1_DISCHG_MASK; -+ desc->active_discharge_on = RT5190A_BUCK1_DISCHG_ONVAL; -+ desc->n_voltages = 1; -+ desc->ops = &rt5190a_fixed_buck_ops; -+ desc->of_map_mode = rt5190a_of_map_mode; -+ break; -+ case RT5190A_IDX_BUCK2: -+ desc->vsel_reg = RT5190A_REG_BUCK2VSEL; -+ desc->vsel_mask = RT5190A_VSEL_MASK; -+ desc->min_uV = RT5190A_BUCK23_MINUV; -+ desc->uV_step = RT5190A_BUCK23_STEPUV; -+ desc->n_voltages = RT5190A_BUCK23_STEPNUM; -+ desc->ops = &rt5190a_ranged_buck_ops; -+ break; -+ case RT5190A_IDX_BUCK3: -+ desc->vsel_reg = RT5190A_REG_BUCK3VSEL; -+ desc->vsel_mask = RT5190A_VSEL_MASK; -+ desc->min_uV = RT5190A_BUCK23_MINUV; -+ desc->uV_step = RT5190A_BUCK23_STEPUV; -+ desc->n_voltages = RT5190A_BUCK23_STEPNUM; -+ desc->ops = &rt5190a_ranged_buck_ops; -+ break; -+ case RT5190A_IDX_BUCK4: -+ desc->n_voltages = 1; -+ desc->ops = &rt5190a_fixed_buck_ops; -+ desc->of_map_mode = rt5190a_of_map_mode; -+ break; -+ case RT5190A_IDX_LDO: -+ desc->n_voltages = 1; -+ desc->ops = &rt5190a_fixed_ldo_ops; -+ break; -+ } -+} -+ -+static struct of_regulator_match rt5190a_regulator_match[] = { -+ { .name = "buck1", }, -+ { .name = "buck2", }, -+ { .name = "buck3", }, -+ { .name = "buck4", }, -+ { .name = "ldo", } -+}; -+ -+static int rt5190a_parse_regulator_dt_data(struct rt5190a_priv *priv) -+{ -+ struct device_node *regulator_np; -+ struct regulator_desc *reg_desc; -+ struct of_regulator_match *match; -+ int i, ret; -+ -+ for (i = 0; i < RT5190A_MAX_IDX; i++) { -+ reg_desc = priv->rdesc + i; -+ match = rt5190a_regulator_match + i; -+ -+ rt5190a_fillin_regulator_desc(reg_desc, i); -+ -+ match->desc = reg_desc; -+ } -+ -+ regulator_np = of_get_child_by_name(priv->dev->of_node, "regulators"); -+ if (!regulator_np) { -+ dev_err(priv->dev, "Could not find 'regulators' node\n"); -+ return -ENODEV; -+ } -+ -+ ret = of_regulator_match(priv->dev, regulator_np, -+ rt5190a_regulator_match, -+ ARRAY_SIZE(rt5190a_regulator_match)); -+ -+ of_node_put(regulator_np); -+ -+ if (ret < 0) { -+ dev_err(priv->dev, -+ "Error parsing regulator init data: %d\n", ret); -+ return ret; -+ } -+ -+ for (i = 0; i < RT5190A_MAX_IDX; i++) { -+ match = rt5190a_regulator_match + i; -+ -+ ret = rt5190a_of_parse_cb(priv, i, match); -+ if (ret) { -+ dev_err(priv->dev, "Failed in [%d] of_parse_cb\n", i); -+ return ret; -+ } -+ } -+ -+ return 0; -+} -+ -+static const struct reg_sequence rt5190a_init_patch[] = { -+ { 0x09, 0x3d, }, -+ { 0x0a, 0x3e, }, -+ { 0x0b, 0x01, }, -+ { 0x10, 0xff, }, -+ { 0x11, 0xff, }, -+ { 0x12, 0xff, }, -+ { 0x13, 0xff, }, -+ { 0x14, 0, }, -+ { 0x15, 0, }, -+ { 0x16, 0x3e, }, -+ { 0x17, 0, } -+}; -+ -+static int rt5190a_device_initialize(struct rt5190a_priv *priv) -+{ -+ bool mute_enable; -+ int ret; -+ -+ ret = regmap_register_patch(priv->regmap, rt5190a_init_patch, -+ ARRAY_SIZE(rt5190a_init_patch)); -+ if (ret) { -+ dev_err(priv->dev, "Failed to do register patch\n"); -+ return ret; -+ } -+ -+ mute_enable = device_property_read_bool(priv->dev, -+ "richtek,mute-enable"); -+ -+ if (mute_enable) { -+ ret = regmap_write(priv->regmap, RT5190A_REG_MUTECNTL, 0x00); -+ if (ret) { -+ dev_err(priv->dev, "Failed to enable mute function\n"); -+ return ret; -+ } -+ } -+ -+ return 0; -+} -+ -+static int rt5190a_device_check(struct rt5190a_priv *priv) -+{ -+ u16 devid; -+ int ret; -+ -+ ret = regmap_raw_read(priv->regmap, RT5190A_REG_MANUFACTURE, &devid, -+ sizeof(devid)); -+ if (ret) -+ return ret; -+ -+ if (devid) { -+ dev_err(priv->dev, "Incorrect device id 0x%04x\n", devid); -+ return -ENODEV; -+ } -+ -+ return 0; -+} -+ -+static const struct regmap_config rt5190a_regmap_config = { -+ .reg_bits = 8, -+ .val_bits = 8, -+ .max_register = RT5190A_REG_HOTDIEMASK, -+}; -+ -+static int rt5190a_probe(struct i2c_client *i2c) -+{ -+ struct rt5190a_priv *priv; -+ struct regulator_config cfg = {}; -+ int i, ret; -+ -+ priv = devm_kzalloc(&i2c->dev, sizeof(*priv), GFP_KERNEL); -+ if (!priv) -+ return -ENOMEM; -+ -+ priv->dev = &i2c->dev; -+ -+ priv->regmap = devm_regmap_init_i2c(i2c, &rt5190a_regmap_config); -+ if (IS_ERR(priv->regmap)) { -+ dev_err(&i2c->dev, "Failed to allocate regmap\n"); -+ return PTR_ERR(priv->regmap); -+ } -+ -+ ret = rt5190a_device_check(priv); -+ if (ret) { -+ dev_err(&i2c->dev, "Failed to check device %d\n", ret); -+ return ret; -+ } -+ -+ ret = rt5190a_device_initialize(priv); -+ if (ret) { -+ dev_err(&i2c->dev, "Failed to initialize the device\n"); -+ return ret; -+ } -+ -+ ret = rt5190a_parse_regulator_dt_data(priv); -+ if (ret) { -+ dev_err(&i2c->dev, "Failed to parse regulator dt\n"); -+ return ret; -+ } -+ -+ cfg.dev = &i2c->dev; -+ cfg.regmap = priv->regmap; -+ -+ for (i = 0; i < RT5190A_MAX_IDX; i++) { -+ struct regulator_desc *desc = priv->rdesc + i; -+ struct of_regulator_match *match = rt5190a_regulator_match + i; -+ -+ cfg.init_data = match->init_data; -+ cfg.of_node = match->of_node; -+ -+ priv->rdev[i] = devm_regulator_register(&i2c->dev, desc, &cfg); -+ if (IS_ERR(priv->rdev[i])) { -+ dev_err(&i2c->dev, "Failed to register regulator %s\n", -+ desc->name); -+ return PTR_ERR(priv->rdev[i]); -+ } -+ } -+ -+ if (i2c->irq) { -+ ret = devm_request_threaded_irq(&i2c->dev, i2c->irq, NULL, -+ rt5190a_irq_handler, -+ IRQF_ONESHOT, -+ dev_name(&i2c->dev), priv); -+ if (ret) { -+ dev_err(&i2c->dev, "Failed to register interrupt\n"); -+ return ret; -+ } -+ } -+ -+ return 0; -+} -+ -+static const struct of_device_id __maybe_unused rt5190a_device_table[] = { -+ { .compatible = "richtek,rt5190a", }, -+ {} -+}; -+MODULE_DEVICE_TABLE(of, rt5190a_device_table); -+ -+static struct i2c_driver rt5190a_driver = { -+ .driver = { -+ .name = "rt5190a", -+ .of_match_table = rt5190a_device_table, -+ }, -+ .probe_new = rt5190a_probe, -+}; -+module_i2c_driver(rt5190a_driver); -+ -+MODULE_AUTHOR("ChiYuan Huang "); -+MODULE_DESCRIPTION("Richtek RT5190A Regulator Driver"); -+MODULE_LICENSE("GPL v2"); diff --git a/target/linux/mediatek/patches-5.15/840-v5.16-i2c-mediatek-Reset-the-handshake-signal-between-i2c-.patch b/target/linux/mediatek/patches-5.15/840-v5.16-i2c-mediatek-Reset-the-handshake-signal-between-i2c-.patch deleted file mode 100644 index 8b01196409..0000000000 --- a/target/linux/mediatek/patches-5.15/840-v5.16-i2c-mediatek-Reset-the-handshake-signal-between-i2c-.patch +++ /dev/null @@ -1,74 +0,0 @@ -From 95e4dfbf33dc0a0843ba20db811f7ea271235e1e Mon Sep 17 00:00:00 2001 -From: Kewei Xu -Date: Sun, 10 Oct 2021 15:05:12 +0800 -Subject: [PATCH 01/16] i2c: mediatek: Reset the handshake signal between i2c - and dma - -Due to changes in the hardware design of the handshaking signal -between i2c and dma, it is necessary to reset the handshaking -signal before each transfer to ensure that the multi-msgs can -be transferred correctly. - -Signed-off-by: Kewei Xu -Reviewed-by: Qii Wang -Signed-off-by: Wolfram Sang ---- - drivers/i2c/busses/i2c-mt65xx.c | 26 ++++++++++++++++++++++++++ - 1 file changed, 26 insertions(+) - ---- a/drivers/i2c/busses/i2c-mt65xx.c -+++ b/drivers/i2c/busses/i2c-mt65xx.c -@@ -15,6 +15,7 @@ - #include - #include - #include -+#include - #include - #include - #include -@@ -49,6 +50,8 @@ - #define I2C_RD_TRANAC_VALUE 0x0001 - #define I2C_SCL_MIS_COMP_VALUE 0x0000 - #define I2C_CHN_CLR_FLAG 0x0000 -+#define I2C_RELIABILITY 0x0010 -+#define I2C_DMAACK_ENABLE 0x0008 - - #define I2C_DMA_CON_TX 0x0000 - #define I2C_DMA_CON_RX 0x0001 -@@ -851,6 +854,7 @@ static int mtk_i2c_do_transfer(struct mt - u16 restart_flag = 0; - u16 dma_sync = 0; - u32 reg_4g_mode; -+ u32 reg_dma_reset; - u8 *dma_rd_buf = NULL; - u8 *dma_wr_buf = NULL; - dma_addr_t rpaddr = 0; -@@ -864,6 +868,28 @@ static int mtk_i2c_do_transfer(struct mt - - reinit_completion(&i2c->msg_complete); - -+ if (i2c->dev_comp->apdma_sync && -+ i2c->op != I2C_MASTER_WRRD && num > 1) { -+ mtk_i2c_writew(i2c, 0x00, OFFSET_DEBUGCTRL); -+ writel(I2C_DMA_HANDSHAKE_RST | I2C_DMA_WARM_RST, -+ i2c->pdmabase + OFFSET_RST); -+ -+ ret = readw_poll_timeout(i2c->pdmabase + OFFSET_RST, -+ reg_dma_reset, -+ !(reg_dma_reset & I2C_DMA_WARM_RST), -+ 0, 100); -+ if (ret) { -+ dev_err(i2c->dev, "DMA warm reset timeout\n"); -+ return -ETIMEDOUT; -+ } -+ -+ writel(I2C_DMA_CLR_FLAG, i2c->pdmabase + OFFSET_RST); -+ mtk_i2c_writew(i2c, I2C_HANDSHAKE_RST, OFFSET_SOFTRESET); -+ mtk_i2c_writew(i2c, I2C_CHN_CLR_FLAG, OFFSET_SOFTRESET); -+ mtk_i2c_writew(i2c, I2C_RELIABILITY | I2C_DMAACK_ENABLE, -+ OFFSET_DEBUGCTRL); -+ } -+ - control_reg = mtk_i2c_readw(i2c, OFFSET_CONTROL) & - ~(I2C_CONTROL_DIR_CHANGE | I2C_CONTROL_RS); - if ((i2c->speed_hz > I2C_MAX_FAST_MODE_PLUS_FREQ) || (left_num >= 1)) diff --git a/target/linux/mediatek/patches-5.15/841-v5.16-i2c-mediatek-Dump-i2c-dma-register-when-a-timeout-oc.patch b/target/linux/mediatek/patches-5.15/841-v5.16-i2c-mediatek-Dump-i2c-dma-register-when-a-timeout-oc.patch deleted file mode 100644 index a2d2521c77..0000000000 --- a/target/linux/mediatek/patches-5.15/841-v5.16-i2c-mediatek-Dump-i2c-dma-register-when-a-timeout-oc.patch +++ /dev/null @@ -1,102 +0,0 @@ -From 5b8e29e566e086ef9b5b9ea0d054370a295e1d05 Mon Sep 17 00:00:00 2001 -From: Kewei Xu -Date: Sun, 10 Oct 2021 15:05:13 +0800 -Subject: [PATCH 02/16] i2c: mediatek: Dump i2c/dma register when a timeout - occurs - -When a timeout error occurs in i2c transter, it is usually related -to the i2c/dma IP hardware configuration. Therefore, the purpose of -this patch is to dump the key register values of i2c/dma when a -timeout occurs in i2c for debugging. - -Signed-off-by: Kewei Xu -Reviewed-by: Qii Wang -Signed-off-by: Wolfram Sang ---- - drivers/i2c/busses/i2c-mt65xx.c | 54 +++++++++++++++++++++++++++++++++ - 1 file changed, 54 insertions(+) - ---- a/drivers/i2c/busses/i2c-mt65xx.c -+++ b/drivers/i2c/busses/i2c-mt65xx.c -@@ -130,6 +130,7 @@ enum I2C_REGS_OFFSET { - OFFSET_HS, - OFFSET_SOFTRESET, - OFFSET_DCM_EN, -+ OFFSET_MULTI_DMA, - OFFSET_PATH_DIR, - OFFSET_DEBUGSTAT, - OFFSET_DEBUGCTRL, -@@ -197,6 +198,7 @@ static const u16 mt_i2c_regs_v2[] = { - [OFFSET_TRANSFER_LEN_AUX] = 0x44, - [OFFSET_CLOCK_DIV] = 0x48, - [OFFSET_SOFTRESET] = 0x50, -+ [OFFSET_MULTI_DMA] = 0x8c, - [OFFSET_SCL_MIS_COMP_POINT] = 0x90, - [OFFSET_DEBUGSTAT] = 0xe4, - [OFFSET_DEBUGCTRL] = 0xe8, -@@ -845,6 +847,57 @@ static int mtk_i2c_set_speed(struct mtk_ - return 0; - } - -+static void i2c_dump_register(struct mtk_i2c *i2c) -+{ -+ dev_dbg(i2c->dev, "SLAVE_ADDR: 0x%x, INTR_MASK: 0x%x\n", -+ mtk_i2c_readw(i2c, OFFSET_SLAVE_ADDR), -+ mtk_i2c_readw(i2c, OFFSET_INTR_MASK)); -+ dev_dbg(i2c->dev, "INTR_STAT: 0x%x, CONTROL: 0x%x\n", -+ mtk_i2c_readw(i2c, OFFSET_INTR_STAT), -+ mtk_i2c_readw(i2c, OFFSET_CONTROL)); -+ dev_dbg(i2c->dev, "TRANSFER_LEN: 0x%x, TRANSAC_LEN: 0x%x\n", -+ mtk_i2c_readw(i2c, OFFSET_TRANSFER_LEN), -+ mtk_i2c_readw(i2c, OFFSET_TRANSAC_LEN)); -+ dev_dbg(i2c->dev, "DELAY_LEN: 0x%x, HTIMING: 0x%x\n", -+ mtk_i2c_readw(i2c, OFFSET_DELAY_LEN), -+ mtk_i2c_readw(i2c, OFFSET_TIMING)); -+ dev_dbg(i2c->dev, "START: 0x%x, EXT_CONF: 0x%x\n", -+ mtk_i2c_readw(i2c, OFFSET_START), -+ mtk_i2c_readw(i2c, OFFSET_EXT_CONF)); -+ dev_dbg(i2c->dev, "HS: 0x%x, IO_CONFIG: 0x%x\n", -+ mtk_i2c_readw(i2c, OFFSET_HS), -+ mtk_i2c_readw(i2c, OFFSET_IO_CONFIG)); -+ dev_dbg(i2c->dev, "DCM_EN: 0x%x, TRANSFER_LEN_AUX: 0x%x\n", -+ mtk_i2c_readw(i2c, OFFSET_DCM_EN), -+ mtk_i2c_readw(i2c, OFFSET_TRANSFER_LEN_AUX)); -+ dev_dbg(i2c->dev, "CLOCK_DIV: 0x%x, FIFO_STAT: 0x%x\n", -+ mtk_i2c_readw(i2c, OFFSET_CLOCK_DIV), -+ mtk_i2c_readw(i2c, OFFSET_FIFO_STAT)); -+ dev_dbg(i2c->dev, "DEBUGCTRL : 0x%x, DEBUGSTAT: 0x%x\n", -+ mtk_i2c_readw(i2c, OFFSET_DEBUGCTRL), -+ mtk_i2c_readw(i2c, OFFSET_DEBUGSTAT)); -+ if (i2c->dev_comp->regs == mt_i2c_regs_v2) { -+ dev_dbg(i2c->dev, "LTIMING: 0x%x, MULTI_DMA: 0x%x\n", -+ mtk_i2c_readw(i2c, OFFSET_LTIMING), -+ mtk_i2c_readw(i2c, OFFSET_MULTI_DMA)); -+ } -+ dev_dbg(i2c->dev, "\nDMA_INT_FLAG: 0x%x, DMA_INT_EN: 0x%x\n", -+ readl(i2c->pdmabase + OFFSET_INT_FLAG), -+ readl(i2c->pdmabase + OFFSET_INT_EN)); -+ dev_dbg(i2c->dev, "DMA_EN: 0x%x, DMA_CON: 0x%x\n", -+ readl(i2c->pdmabase + OFFSET_EN), -+ readl(i2c->pdmabase + OFFSET_CON)); -+ dev_dbg(i2c->dev, "DMA_TX_MEM_ADDR: 0x%x, DMA_RX_MEM_ADDR: 0x%x\n", -+ readl(i2c->pdmabase + OFFSET_TX_MEM_ADDR), -+ readl(i2c->pdmabase + OFFSET_RX_MEM_ADDR)); -+ dev_dbg(i2c->dev, "DMA_TX_LEN: 0x%x, DMA_RX_LEN: 0x%x\n", -+ readl(i2c->pdmabase + OFFSET_TX_LEN), -+ readl(i2c->pdmabase + OFFSET_RX_LEN)); -+ dev_dbg(i2c->dev, "DMA_TX_4G_MODE: 0x%x, DMA_RX_4G_MODE: 0x%x", -+ readl(i2c->pdmabase + OFFSET_TX_4G_MODE), -+ readl(i2c->pdmabase + OFFSET_RX_4G_MODE)); -+} -+ - static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs, - int num, int left_num) - { -@@ -1075,6 +1128,7 @@ static int mtk_i2c_do_transfer(struct mt - - if (ret == 0) { - dev_dbg(i2c->dev, "addr: %x, transfer timeout\n", msgs->addr); -+ i2c_dump_register(i2c); - mtk_i2c_init_hw(i2c); - return -ETIMEDOUT; - } diff --git a/target/linux/mediatek/patches-5.15/842-v5.18-i2c-mediatek-Add-i2c-compatible-for-Mediatek-MT8186.patch b/target/linux/mediatek/patches-5.15/842-v5.18-i2c-mediatek-Add-i2c-compatible-for-Mediatek-MT8186.patch deleted file mode 100644 index 184fe94ff8..0000000000 --- a/target/linux/mediatek/patches-5.15/842-v5.18-i2c-mediatek-Add-i2c-compatible-for-Mediatek-MT8186.patch +++ /dev/null @@ -1,45 +0,0 @@ -From 83630e3c6147bf7bb18a18f3d5a99462464f450b Mon Sep 17 00:00:00 2001 -From: Kewei Xu -Date: Tue, 25 Jan 2022 19:04:13 +0800 -Subject: [PATCH 03/16] i2c: mediatek: Add i2c compatible for Mediatek MT8186 - -Add i2c compatible for MT8186. Compare to MT8192 i2c controller, -MT8186 doesn't need handshake signal witch apdma. - -Signed-off-by: Kewei Xu -Reviewed-by: Qii Wang -Signed-off-by: Wolfram Sang ---- - drivers/i2c/busses/i2c-mt65xx.c | 14 ++++++++++++++ - 1 file changed, 14 insertions(+) - ---- a/drivers/i2c/busses/i2c-mt65xx.c -+++ b/drivers/i2c/busses/i2c-mt65xx.c -@@ -397,6 +397,19 @@ static const struct mtk_i2c_compatible m - .max_dma_support = 33, - }; - -+static const struct mtk_i2c_compatible mt8186_compat = { -+ .regs = mt_i2c_regs_v2, -+ .pmic_i2c = 0, -+ .dcm = 0, -+ .auto_restart = 1, -+ .aux_len_reg = 1, -+ .timing_adjust = 1, -+ .dma_sync = 0, -+ .ltiming_adjust = 1, -+ .apdma_sync = 0, -+ .max_dma_support = 36, -+}; -+ - static const struct mtk_i2c_compatible mt8192_compat = { - .quirks = &mt8183_i2c_quirks, - .regs = mt_i2c_regs_v2, -@@ -418,6 +431,7 @@ static const struct of_device_id mtk_i2c - { .compatible = "mediatek,mt7622-i2c", .data = &mt7622_compat }, - { .compatible = "mediatek,mt8173-i2c", .data = &mt8173_compat }, - { .compatible = "mediatek,mt8183-i2c", .data = &mt8183_compat }, -+ { .compatible = "mediatek,mt8186-i2c", .data = &mt8186_compat }, - { .compatible = "mediatek,mt8192-i2c", .data = &mt8192_compat }, - {} - }; diff --git a/target/linux/mediatek/patches-5.15/843-v5.18-i2c-mediatek-modify-bus-speed-calculation-formula.patch b/target/linux/mediatek/patches-5.15/843-v5.18-i2c-mediatek-modify-bus-speed-calculation-formula.patch deleted file mode 100644 index 0ace4a6701..0000000000 --- a/target/linux/mediatek/patches-5.15/843-v5.18-i2c-mediatek-modify-bus-speed-calculation-formula.patch +++ /dev/null @@ -1,132 +0,0 @@ -From f606aab3f1a49d723d66e14e545f6ca45005bda6 Mon Sep 17 00:00:00 2001 -From: Kewei Xu -Date: Thu, 17 Feb 2022 20:22:43 +0800 -Subject: [PATCH 04/16] i2c: mediatek: modify bus speed calculation formula - -When clock-div is 0 or greater than 1, the bus speed -calculated by the old speed calculation formula will be -larger than the target speed. So we update the formula. - -Signed-off-by: Kewei Xu -Reviewed-by: AngeloGioacchino Del Regno -Reviewed-by: Qii Wang -Signed-off-by: Wolfram Sang ---- - drivers/i2c/busses/i2c-mt65xx.c | 51 ++++++++++++++++++++++++++------- - 1 file changed, 41 insertions(+), 10 deletions(-) - ---- a/drivers/i2c/busses/i2c-mt65xx.c -+++ b/drivers/i2c/busses/i2c-mt65xx.c -@@ -67,11 +67,12 @@ - - #define MAX_SAMPLE_CNT_DIV 8 - #define MAX_STEP_CNT_DIV 64 --#define MAX_CLOCK_DIV 256 -+#define MAX_CLOCK_DIV_8BITS 256 -+#define MAX_CLOCK_DIV_5BITS 32 - #define MAX_HS_STEP_CNT_DIV 8 --#define I2C_STANDARD_MODE_BUFFER (1000 / 2) --#define I2C_FAST_MODE_BUFFER (300 / 2) --#define I2C_FAST_MODE_PLUS_BUFFER (20 / 2) -+#define I2C_STANDARD_MODE_BUFFER (1000 / 3) -+#define I2C_FAST_MODE_BUFFER (300 / 3) -+#define I2C_FAST_MODE_PLUS_BUFFER (20 / 3) - - #define I2C_CONTROL_RS (0x1 << 1) - #define I2C_CONTROL_DMA_EN (0x1 << 2) -@@ -604,6 +605,31 @@ static int mtk_i2c_max_step_cnt(unsigned - return MAX_STEP_CNT_DIV; - } - -+static int mtk_i2c_get_clk_div_restri(struct mtk_i2c *i2c, -+ unsigned int sample_cnt) -+{ -+ int clk_div_restri = 0; -+ -+ if (i2c->dev_comp->ltiming_adjust == 0) -+ return 0; -+ -+ if (sample_cnt == 1) { -+ if (i2c->ac_timing.inter_clk_div == 0) -+ clk_div_restri = 0; -+ else -+ clk_div_restri = 1; -+ } else { -+ if (i2c->ac_timing.inter_clk_div == 0) -+ clk_div_restri = -1; -+ else if (i2c->ac_timing.inter_clk_div == 1) -+ clk_div_restri = 0; -+ else -+ clk_div_restri = 1; -+ } -+ -+ return clk_div_restri; -+} -+ - /* - * Check and Calculate i2c ac-timing - * -@@ -732,6 +758,7 @@ static int mtk_i2c_calculate_speed(struc - unsigned int best_mul; - unsigned int cnt_mul; - int ret = -EINVAL; -+ int clk_div_restri = 0; - - if (target_speed > I2C_MAX_HIGH_SPEED_MODE_FREQ) - target_speed = I2C_MAX_HIGH_SPEED_MODE_FREQ; -@@ -749,7 +776,8 @@ static int mtk_i2c_calculate_speed(struc - * optimizing for sample_cnt * step_cnt being minimal - */ - for (sample_cnt = 1; sample_cnt <= MAX_SAMPLE_CNT_DIV; sample_cnt++) { -- step_cnt = DIV_ROUND_UP(opt_div, sample_cnt); -+ clk_div_restri = mtk_i2c_get_clk_div_restri(i2c, sample_cnt); -+ step_cnt = DIV_ROUND_UP(opt_div + clk_div_restri, sample_cnt); - cnt_mul = step_cnt * sample_cnt; - if (step_cnt > max_step_cnt) - continue; -@@ -763,7 +791,7 @@ static int mtk_i2c_calculate_speed(struc - best_mul = cnt_mul; - base_sample_cnt = sample_cnt; - base_step_cnt = step_cnt; -- if (best_mul == opt_div) -+ if (best_mul == (opt_div + clk_div_restri)) - break; - } - } -@@ -774,7 +802,8 @@ static int mtk_i2c_calculate_speed(struc - sample_cnt = base_sample_cnt; - step_cnt = base_step_cnt; - -- if ((clk_src / (2 * sample_cnt * step_cnt)) > target_speed) { -+ if ((clk_src / (2 * (sample_cnt * step_cnt - clk_div_restri))) > -+ target_speed) { - /* In this case, hardware can't support such - * low i2c_bus_freq - */ -@@ -803,13 +832,16 @@ static int mtk_i2c_set_speed(struct mtk_ - target_speed = i2c->speed_hz; - parent_clk /= i2c->clk_src_div; - -- if (i2c->dev_comp->timing_adjust) -- max_clk_div = MAX_CLOCK_DIV; -+ if (i2c->dev_comp->timing_adjust && i2c->dev_comp->ltiming_adjust) -+ max_clk_div = MAX_CLOCK_DIV_5BITS; -+ else if (i2c->dev_comp->timing_adjust) -+ max_clk_div = MAX_CLOCK_DIV_8BITS; - else - max_clk_div = 1; - - for (clk_div = 1; clk_div <= max_clk_div; clk_div++) { - clk_src = parent_clk / clk_div; -+ i2c->ac_timing.inter_clk_div = clk_div - 1; - - if (target_speed > I2C_MAX_FAST_MODE_PLUS_FREQ) { - /* Set master code speed register */ -@@ -856,7 +888,6 @@ static int mtk_i2c_set_speed(struct mtk_ - break; - } - -- i2c->ac_timing.inter_clk_div = clk_div - 1; - - return 0; - } diff --git a/target/linux/mediatek/patches-5.15/844-v5.18-i2c-mediatek-remove-redundant-null-check.patch b/target/linux/mediatek/patches-5.15/844-v5.18-i2c-mediatek-remove-redundant-null-check.patch deleted file mode 100644 index 8f3c965a8d..0000000000 --- a/target/linux/mediatek/patches-5.15/844-v5.18-i2c-mediatek-remove-redundant-null-check.patch +++ /dev/null @@ -1,41 +0,0 @@ -From eb4a2ae019815946f574cd9f8209e12bdcd8fd34 Mon Sep 17 00:00:00 2001 -From: Xu Wang -Date: Wed, 30 Sep 2020 08:42:33 +0000 -Subject: [PATCH 05/16] i2c: mediatek: remove redundant null check - -Because clk_disable_unprepare already checked NULL clock parameter, -so the additional checks are unnecessary, just remove it - -Signed-off-by: Xu Wang -Reviewed-by: Qii Wang -Signed-off-by: Wolfram Sang ---- - drivers/i2c/busses/i2c-mt65xx.c | 9 +++------ - 1 file changed, 3 insertions(+), 6 deletions(-) - ---- a/drivers/i2c/busses/i2c-mt65xx.c -+++ b/drivers/i2c/busses/i2c-mt65xx.c -@@ -476,8 +476,7 @@ static int mtk_i2c_clock_enable(struct m - return 0; - - err_arb: -- if (i2c->have_pmic) -- clk_disable_unprepare(i2c->clk_pmic); -+ clk_disable_unprepare(i2c->clk_pmic); - err_pmic: - clk_disable_unprepare(i2c->clk_main); - err_main: -@@ -488,11 +487,9 @@ err_main: - - static void mtk_i2c_clock_disable(struct mtk_i2c *i2c) - { -- if (i2c->clk_arb) -- clk_disable_unprepare(i2c->clk_arb); -+ clk_disable_unprepare(i2c->clk_arb); - -- if (i2c->have_pmic) -- clk_disable_unprepare(i2c->clk_pmic); -+ clk_disable_unprepare(i2c->clk_pmic); - - clk_disable_unprepare(i2c->clk_main); - clk_disable_unprepare(i2c->clk_dma); diff --git a/target/linux/mediatek/patches-5.15/845-v5.18-i2c-mt65xx-Simplify-with-clk-bulk.patch b/target/linux/mediatek/patches-5.15/845-v5.18-i2c-mt65xx-Simplify-with-clk-bulk.patch deleted file mode 100644 index 71d083f31a..0000000000 --- a/target/linux/mediatek/patches-5.15/845-v5.18-i2c-mt65xx-Simplify-with-clk-bulk.patch +++ /dev/null @@ -1,234 +0,0 @@ -From cc6faa5e0772296d815fd298c231277d47308a6a Mon Sep 17 00:00:00 2001 -From: AngeloGioacchino Del Regno -Date: Thu, 3 Mar 2022 10:15:47 +0100 -Subject: [PATCH 06/16] i2c: mt65xx: Simplify with clk-bulk - -Since depending on the SoC or specific bus functionality some clocks -may be optional, we cannot get the benefit of using devm_clk_bulk_get() -but, by migrating to clk-bulk, we are able to remove the custom functions -mtk_i2c_clock_enable() and mtk_i2c_clock_disable(), increasing common -APIs usage, hence (lightly) decreasing kernel footprint. - -Signed-off-by: AngeloGioacchino Del Regno -Reviewed-by: Qii Wang -Signed-off-by: Wolfram Sang ---- - drivers/i2c/busses/i2c-mt65xx.c | 124 +++++++++++++------------------- - 1 file changed, 51 insertions(+), 73 deletions(-) - ---- a/drivers/i2c/busses/i2c-mt65xx.c -+++ b/drivers/i2c/busses/i2c-mt65xx.c -@@ -86,6 +86,27 @@ - - #define I2C_DRV_NAME "i2c-mt65xx" - -+/** -+ * enum i2c_mt65xx_clks - Clocks enumeration for MT65XX I2C -+ * -+ * @I2C_MT65XX_CLK_MAIN: main clock for i2c bus -+ * @I2C_MT65XX_CLK_DMA: DMA clock for i2c via DMA -+ * @I2C_MT65XX_CLK_PMIC: PMIC clock for i2c from PMIC -+ * @I2C_MT65XX_CLK_ARB: Arbitrator clock for i2c -+ * @I2C_MT65XX_CLK_MAX: Number of supported clocks -+ */ -+enum i2c_mt65xx_clks { -+ I2C_MT65XX_CLK_MAIN = 0, -+ I2C_MT65XX_CLK_DMA, -+ I2C_MT65XX_CLK_PMIC, -+ I2C_MT65XX_CLK_ARB, -+ I2C_MT65XX_CLK_MAX -+}; -+ -+static const char * const i2c_mt65xx_clk_ids[I2C_MT65XX_CLK_MAX] = { -+ "main", "dma", "pmic", "arb" -+}; -+ - enum DMA_REGS_OFFSET { - OFFSET_INT_FLAG = 0x0, - OFFSET_INT_EN = 0x04, -@@ -244,10 +265,7 @@ struct mtk_i2c { - /* set in i2c probe */ - void __iomem *base; /* i2c base addr */ - void __iomem *pdmabase; /* dma base address*/ -- struct clk *clk_main; /* main clock for i2c bus */ -- struct clk *clk_dma; /* DMA clock for i2c via DMA */ -- struct clk *clk_pmic; /* PMIC clock for i2c from PMIC */ -- struct clk *clk_arb; /* Arbitrator clock for i2c */ -+ struct clk_bulk_data clocks[I2C_MT65XX_CLK_MAX]; /* clocks for i2c */ - bool have_pmic; /* can use i2c pins from PMIC */ - bool use_push_pull; /* IO config push-pull mode */ - -@@ -449,52 +467,6 @@ static void mtk_i2c_writew(struct mtk_i2 - writew(val, i2c->base + i2c->dev_comp->regs[reg]); - } - --static int mtk_i2c_clock_enable(struct mtk_i2c *i2c) --{ -- int ret; -- -- ret = clk_prepare_enable(i2c->clk_dma); -- if (ret) -- return ret; -- -- ret = clk_prepare_enable(i2c->clk_main); -- if (ret) -- goto err_main; -- -- if (i2c->have_pmic) { -- ret = clk_prepare_enable(i2c->clk_pmic); -- if (ret) -- goto err_pmic; -- } -- -- if (i2c->clk_arb) { -- ret = clk_prepare_enable(i2c->clk_arb); -- if (ret) -- goto err_arb; -- } -- -- return 0; -- --err_arb: -- clk_disable_unprepare(i2c->clk_pmic); --err_pmic: -- clk_disable_unprepare(i2c->clk_main); --err_main: -- clk_disable_unprepare(i2c->clk_dma); -- -- return ret; --} -- --static void mtk_i2c_clock_disable(struct mtk_i2c *i2c) --{ -- clk_disable_unprepare(i2c->clk_arb); -- -- clk_disable_unprepare(i2c->clk_pmic); -- -- clk_disable_unprepare(i2c->clk_main); -- clk_disable_unprepare(i2c->clk_dma); --} -- - static void mtk_i2c_init_hw(struct mtk_i2c *i2c) - { - u16 control_reg; -@@ -1191,7 +1163,7 @@ static int mtk_i2c_transfer(struct i2c_a - int left_num = num; - struct mtk_i2c *i2c = i2c_get_adapdata(adap); - -- ret = mtk_i2c_clock_enable(i2c); -+ ret = clk_bulk_prepare_enable(I2C_MT65XX_CLK_MAX, i2c->clocks); - if (ret) - return ret; - -@@ -1245,7 +1217,7 @@ static int mtk_i2c_transfer(struct i2c_a - ret = num; - - err_exit: -- mtk_i2c_clock_disable(i2c); -+ clk_bulk_disable_unprepare(I2C_MT65XX_CLK_MAX, i2c->clocks); - return ret; - } - -@@ -1323,9 +1295,8 @@ static int mtk_i2c_probe(struct platform - { - int ret = 0; - struct mtk_i2c *i2c; -- struct clk *clk; - struct resource *res; -- int irq; -+ int i, irq, speed_clk; - - i2c = devm_kzalloc(&pdev->dev, sizeof(*i2c), GFP_KERNEL); - if (!i2c) -@@ -1371,35 +1342,42 @@ static int mtk_i2c_probe(struct platform - if (i2c->have_pmic && !i2c->dev_comp->pmic_i2c) - return -EINVAL; - -- i2c->clk_main = devm_clk_get(&pdev->dev, "main"); -- if (IS_ERR(i2c->clk_main)) { -+ /* Fill in clk-bulk IDs */ -+ for (i = 0; i < I2C_MT65XX_CLK_MAX; i++) -+ i2c->clocks[i].id = i2c_mt65xx_clk_ids[i]; -+ -+ /* Get clocks one by one, some may be optional */ -+ i2c->clocks[I2C_MT65XX_CLK_MAIN].clk = devm_clk_get(&pdev->dev, "main"); -+ if (IS_ERR(i2c->clocks[I2C_MT65XX_CLK_MAIN].clk)) { - dev_err(&pdev->dev, "cannot get main clock\n"); -- return PTR_ERR(i2c->clk_main); -+ return PTR_ERR(i2c->clocks[I2C_MT65XX_CLK_MAIN].clk); - } - -- i2c->clk_dma = devm_clk_get(&pdev->dev, "dma"); -- if (IS_ERR(i2c->clk_dma)) { -+ i2c->clocks[I2C_MT65XX_CLK_DMA].clk = devm_clk_get(&pdev->dev, "dma"); -+ if (IS_ERR(i2c->clocks[I2C_MT65XX_CLK_DMA].clk)) { - dev_err(&pdev->dev, "cannot get dma clock\n"); -- return PTR_ERR(i2c->clk_dma); -+ return PTR_ERR(i2c->clocks[I2C_MT65XX_CLK_DMA].clk); - } - -- i2c->clk_arb = devm_clk_get(&pdev->dev, "arb"); -- if (IS_ERR(i2c->clk_arb)) -- i2c->clk_arb = NULL; -+ i2c->clocks[I2C_MT65XX_CLK_ARB].clk = devm_clk_get_optional(&pdev->dev, "arb"); -+ if (IS_ERR(i2c->clocks[I2C_MT65XX_CLK_ARB].clk)) -+ return PTR_ERR(i2c->clocks[I2C_MT65XX_CLK_ARB].clk); - -- clk = i2c->clk_main; - if (i2c->have_pmic) { -- i2c->clk_pmic = devm_clk_get(&pdev->dev, "pmic"); -- if (IS_ERR(i2c->clk_pmic)) { -+ i2c->clocks[I2C_MT65XX_CLK_PMIC].clk = devm_clk_get(&pdev->dev, "pmic"); -+ if (IS_ERR(i2c->clocks[I2C_MT65XX_CLK_PMIC].clk)) { - dev_err(&pdev->dev, "cannot get pmic clock\n"); -- return PTR_ERR(i2c->clk_pmic); -+ return PTR_ERR(i2c->clocks[I2C_MT65XX_CLK_PMIC].clk); - } -- clk = i2c->clk_pmic; -+ speed_clk = I2C_MT65XX_CLK_PMIC; -+ } else { -+ i2c->clocks[I2C_MT65XX_CLK_PMIC].clk = NULL; -+ speed_clk = I2C_MT65XX_CLK_MAIN; - } - - strlcpy(i2c->adap.name, I2C_DRV_NAME, sizeof(i2c->adap.name)); - -- ret = mtk_i2c_set_speed(i2c, clk_get_rate(clk)); -+ ret = mtk_i2c_set_speed(i2c, clk_get_rate(i2c->clocks[speed_clk].clk)); - if (ret) { - dev_err(&pdev->dev, "Failed to set the speed.\n"); - return -EINVAL; -@@ -1414,13 +1392,13 @@ static int mtk_i2c_probe(struct platform - } - } - -- ret = mtk_i2c_clock_enable(i2c); -+ ret = clk_bulk_prepare_enable(I2C_MT65XX_CLK_MAX, i2c->clocks); - if (ret) { - dev_err(&pdev->dev, "clock enable failed!\n"); - return ret; - } - mtk_i2c_init_hw(i2c); -- mtk_i2c_clock_disable(i2c); -+ clk_bulk_disable_unprepare(I2C_MT65XX_CLK_MAX, i2c->clocks); - - ret = devm_request_irq(&pdev->dev, irq, mtk_i2c_irq, - IRQF_NO_SUSPEND | IRQF_TRIGGER_NONE, -@@ -1465,7 +1443,7 @@ static int mtk_i2c_resume_noirq(struct d - int ret; - struct mtk_i2c *i2c = dev_get_drvdata(dev); - -- ret = mtk_i2c_clock_enable(i2c); -+ ret = clk_bulk_prepare_enable(I2C_MT65XX_CLK_MAX, i2c->clocks); - if (ret) { - dev_err(dev, "clock enable failed!\n"); - return ret; -@@ -1473,7 +1451,7 @@ static int mtk_i2c_resume_noirq(struct d - - mtk_i2c_init_hw(i2c); - -- mtk_i2c_clock_disable(i2c); -+ clk_bulk_disable_unprepare(I2C_MT65XX_CLK_MAX, i2c->clocks); - - i2c_mark_adapter_resumed(&i2c->adap); - diff --git a/target/linux/mediatek/patches-5.15/846-v5.18-i2c-mediatek-Add-i2c-compatible-for-Mediatek-MT8168.patch b/target/linux/mediatek/patches-5.15/846-v5.18-i2c-mediatek-Add-i2c-compatible-for-Mediatek-MT8168.patch deleted file mode 100644 index fe5be94fca..0000000000 --- a/target/linux/mediatek/patches-5.15/846-v5.18-i2c-mediatek-Add-i2c-compatible-for-Mediatek-MT8168.patch +++ /dev/null @@ -1,46 +0,0 @@ -From de054c03f90b3ea22bc346fbf78ac716df192b2d Mon Sep 17 00:00:00 2001 -From: Kewei Xu -Date: Mon, 7 Mar 2022 11:36:49 +0800 -Subject: [PATCH 07/16] i2c: mediatek: Add i2c compatible for Mediatek MT8168 - -Add i2c compatible for MT8168. Compare to MT2712 i2c controller, -MT8168 need to synchronize signal with dma. - -Signed-off-by: Kewei Xu -Reviewed-by: AngeloGioacchino Del Regno -Reviewed-by: Qii Wang -Signed-off-by: Wolfram Sang ---- - drivers/i2c/busses/i2c-mt65xx.c | 14 ++++++++++++++ - 1 file changed, 14 insertions(+) - ---- a/drivers/i2c/busses/i2c-mt65xx.c -+++ b/drivers/i2c/busses/i2c-mt65xx.c -@@ -389,6 +389,19 @@ static const struct mtk_i2c_compatible m - .max_dma_support = 32, - }; - -+static const struct mtk_i2c_compatible mt8168_compat = { -+ .regs = mt_i2c_regs_v1, -+ .pmic_i2c = 0, -+ .dcm = 1, -+ .auto_restart = 1, -+ .aux_len_reg = 1, -+ .timing_adjust = 1, -+ .dma_sync = 1, -+ .ltiming_adjust = 0, -+ .apdma_sync = 0, -+ .max_dma_support = 33, -+}; -+ - static const struct mtk_i2c_compatible mt8173_compat = { - .regs = mt_i2c_regs_v1, - .pmic_i2c = 0, -@@ -448,6 +461,7 @@ static const struct of_device_id mtk_i2c - { .compatible = "mediatek,mt6577-i2c", .data = &mt6577_compat }, - { .compatible = "mediatek,mt6589-i2c", .data = &mt6589_compat }, - { .compatible = "mediatek,mt7622-i2c", .data = &mt7622_compat }, -+ { .compatible = "mediatek,mt8168-i2c", .data = &mt8168_compat }, - { .compatible = "mediatek,mt8173-i2c", .data = &mt8173_compat }, - { .compatible = "mediatek,mt8183-i2c", .data = &mt8183_compat }, - { .compatible = "mediatek,mt8186-i2c", .data = &mt8186_compat }, diff --git a/target/linux/mediatek/patches-5.15/847-v5.19-i2c-mediatek-Optimize-master_xfer-and-avoid-circular.patch b/target/linux/mediatek/patches-5.15/847-v5.19-i2c-mediatek-Optimize-master_xfer-and-avoid-circular.patch deleted file mode 100644 index 5c4ce40765..0000000000 --- a/target/linux/mediatek/patches-5.15/847-v5.19-i2c-mediatek-Optimize-master_xfer-and-avoid-circular.patch +++ /dev/null @@ -1,101 +0,0 @@ -From 2831f9a53ec3a16012d2d23590e3ebad6084b763 Mon Sep 17 00:00:00 2001 -From: AngeloGioacchino Del Regno -Date: Mon, 11 Apr 2022 15:21:07 +0200 -Subject: [PATCH 08/16] i2c: mediatek: Optimize master_xfer() and avoid - circular locking -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -Especially (but not only) during probe, it may happen that multiple -devices are communicating via i2c (or multiple i2c busses) and -sometimes while others are probing asynchronously. -For example, a Cr50 TPM may be filling entropy (or userspace may be -reading random data) while the rt5682 (i2c) codec driver reads/sets -some registers, like while getting/setting a clock's rate, which -happens both during probe and during system operation. - -In this driver, the mtk_i2c_transfer() function (which is the i2c -.master_xfer() callback) was granularly managing the clocks by -performing a clk_bulk_prepare_enable() to start them and its inverse. -This is not only creating possible circular locking dependencies in -the some cases (like former explanation), but it's also suboptimal, -as clk_core prepare/unprepare operations are using mutex locking, -which creates a bit of unwanted overhead (for example, i2c trackpads -will call master_xfer() every few milliseconds!). - -With this commit, we avoid both the circular locking and additional -overhead by changing how we handle the clocks in this driver: -- Prepare the clocks during probe (and PM resume) -- Enable/disable clocks in mtk_i2c_transfer() -- Unprepare the clocks only for driver removal (and PM suspend) - -For the sake of providing a full explanation: during probe, the -clocks are not only prepared but also enabled, as this is needed -for some hardware initialization but, after that, we are disabling -but not unpreparing them, leaving an expected state for the -aforementioned clock handling strategy. - -Signed-off-by: AngeloGioacchino Del Regno -Tested-by: Nícolas F. R. A. Prado -Reviewed-by: Qii Wang -Signed-off-by: Wolfram Sang ---- - drivers/i2c/busses/i2c-mt65xx.c | 11 +++++++---- - 1 file changed, 7 insertions(+), 4 deletions(-) - ---- a/drivers/i2c/busses/i2c-mt65xx.c -+++ b/drivers/i2c/busses/i2c-mt65xx.c -@@ -1177,7 +1177,7 @@ static int mtk_i2c_transfer(struct i2c_a - int left_num = num; - struct mtk_i2c *i2c = i2c_get_adapdata(adap); - -- ret = clk_bulk_prepare_enable(I2C_MT65XX_CLK_MAX, i2c->clocks); -+ ret = clk_bulk_enable(I2C_MT65XX_CLK_MAX, i2c->clocks); - if (ret) - return ret; - -@@ -1231,7 +1231,7 @@ static int mtk_i2c_transfer(struct i2c_a - ret = num; - - err_exit: -- clk_bulk_disable_unprepare(I2C_MT65XX_CLK_MAX, i2c->clocks); -+ clk_bulk_disable(I2C_MT65XX_CLK_MAX, i2c->clocks); - return ret; - } - -@@ -1412,7 +1412,7 @@ static int mtk_i2c_probe(struct platform - return ret; - } - mtk_i2c_init_hw(i2c); -- clk_bulk_disable_unprepare(I2C_MT65XX_CLK_MAX, i2c->clocks); -+ clk_bulk_disable(I2C_MT65XX_CLK_MAX, i2c->clocks); - - ret = devm_request_irq(&pdev->dev, irq, mtk_i2c_irq, - IRQF_NO_SUSPEND | IRQF_TRIGGER_NONE, -@@ -1439,6 +1439,8 @@ static int mtk_i2c_remove(struct platfor - - i2c_del_adapter(&i2c->adap); - -+ clk_bulk_unprepare(I2C_MT65XX_CLK_MAX, i2c->clocks); -+ - return 0; - } - -@@ -1448,6 +1450,7 @@ static int mtk_i2c_suspend_noirq(struct - struct mtk_i2c *i2c = dev_get_drvdata(dev); - - i2c_mark_adapter_suspended(&i2c->adap); -+ clk_bulk_unprepare(I2C_MT65XX_CLK_MAX, i2c->clocks); - - return 0; - } -@@ -1465,7 +1468,7 @@ static int mtk_i2c_resume_noirq(struct d - - mtk_i2c_init_hw(i2c); - -- clk_bulk_disable_unprepare(I2C_MT65XX_CLK_MAX, i2c->clocks); -+ clk_bulk_disable(I2C_MT65XX_CLK_MAX, i2c->clocks); - - i2c_mark_adapter_resumed(&i2c->adap); - diff --git a/target/linux/mediatek/patches-5.15/848-v5.19-i2c-mediatek-Fix-an-error-handling-path-in-mtk_i2c_p.patch b/target/linux/mediatek/patches-5.15/848-v5.19-i2c-mediatek-Fix-an-error-handling-path-in-mtk_i2c_p.patch deleted file mode 100644 index 354f12e214..0000000000 --- a/target/linux/mediatek/patches-5.15/848-v5.19-i2c-mediatek-Fix-an-error-handling-path-in-mtk_i2c_p.patch +++ /dev/null @@ -1,48 +0,0 @@ -From 6f3a5814c7aaea4176e0ac8b1ec6dc0a65aa2808 Mon Sep 17 00:00:00 2001 -From: Christophe JAILLET -Date: Sun, 22 May 2022 14:22:07 +0200 -Subject: [PATCH 09/16] i2c: mediatek: Fix an error handling path in - mtk_i2c_probe() - -The clsk are prepared, enabled, then disabled. So if an error occurs after -the disable step, they are still prepared. - -Add an error handling path to unprepare the clks in such a case, as already -done in the .remove function. - -Fixes: 8b4fc246c3ff ("i2c: mediatek: Optimize master_xfer() and avoid circular locking") -Signed-off-by: Christophe JAILLET -Reviewed-by: AngeloGioacchino Del Regno -Reviewed-by: Qii Wang -Signed-off-by: Wolfram Sang ---- - drivers/i2c/busses/i2c-mt65xx.c | 9 +++++++-- - 1 file changed, 7 insertions(+), 2 deletions(-) - ---- a/drivers/i2c/busses/i2c-mt65xx.c -+++ b/drivers/i2c/busses/i2c-mt65xx.c -@@ -1420,17 +1420,22 @@ static int mtk_i2c_probe(struct platform - if (ret < 0) { - dev_err(&pdev->dev, - "Request I2C IRQ %d fail\n", irq); -- return ret; -+ goto err_bulk_unprepare; - } - - i2c_set_adapdata(&i2c->adap, i2c); - ret = i2c_add_adapter(&i2c->adap); - if (ret) -- return ret; -+ goto err_bulk_unprepare; - - platform_set_drvdata(pdev, i2c); - - return 0; -+ -+err_bulk_unprepare: -+ clk_bulk_unprepare(I2C_MT65XX_CLK_MAX, i2c->clocks); -+ -+ return ret; - } - - static int mtk_i2c_remove(struct platform_device *pdev) diff --git a/target/linux/mediatek/patches-5.15/849-v6.0-i2c-mediatek-add-i2c-compatible-for-MT8188.patch b/target/linux/mediatek/patches-5.15/849-v6.0-i2c-mediatek-add-i2c-compatible-for-MT8188.patch deleted file mode 100644 index 744aa96ed0..0000000000 --- a/target/linux/mediatek/patches-5.15/849-v6.0-i2c-mediatek-add-i2c-compatible-for-MT8188.patch +++ /dev/null @@ -1,82 +0,0 @@ -From 94c7f8af2c0a399c8aa66f2522b60c5784b5be6c Mon Sep 17 00:00:00 2001 -From: Kewei Xu -Date: Sat, 6 Aug 2022 18:02:49 +0800 -Subject: [PATCH 10/16] i2c: mediatek: add i2c compatible for MT8188 - -Add i2c compatible for MT8188 and added mt_i2c_regs_v3[], since -MT8188 i2c OFFSET_SLAVE_ADDR register changed from 0x04 to 0x94. - -Signed-off-by: Kewei Xu -Reviewed-by: AngeloGioacchino Del Regno -Reviewed-by: Qii Wang -Signed-off-by: Wolfram Sang ---- - drivers/i2c/busses/i2c-mt65xx.c | 43 +++++++++++++++++++++++++++++++++ - 1 file changed, 43 insertions(+) - ---- a/drivers/i2c/busses/i2c-mt65xx.c -+++ b/drivers/i2c/busses/i2c-mt65xx.c -@@ -229,6 +229,35 @@ static const u16 mt_i2c_regs_v2[] = { - [OFFSET_DCM_EN] = 0xf88, - }; - -+static const u16 mt_i2c_regs_v3[] = { -+ [OFFSET_DATA_PORT] = 0x0, -+ [OFFSET_INTR_MASK] = 0x8, -+ [OFFSET_INTR_STAT] = 0xc, -+ [OFFSET_CONTROL] = 0x10, -+ [OFFSET_TRANSFER_LEN] = 0x14, -+ [OFFSET_TRANSAC_LEN] = 0x18, -+ [OFFSET_DELAY_LEN] = 0x1c, -+ [OFFSET_TIMING] = 0x20, -+ [OFFSET_START] = 0x24, -+ [OFFSET_EXT_CONF] = 0x28, -+ [OFFSET_LTIMING] = 0x2c, -+ [OFFSET_HS] = 0x30, -+ [OFFSET_IO_CONFIG] = 0x34, -+ [OFFSET_FIFO_ADDR_CLR] = 0x38, -+ [OFFSET_SDA_TIMING] = 0x3c, -+ [OFFSET_TRANSFER_LEN_AUX] = 0x44, -+ [OFFSET_CLOCK_DIV] = 0x48, -+ [OFFSET_SOFTRESET] = 0x50, -+ [OFFSET_MULTI_DMA] = 0x8c, -+ [OFFSET_SCL_MIS_COMP_POINT] = 0x90, -+ [OFFSET_SLAVE_ADDR] = 0x94, -+ [OFFSET_DEBUGSTAT] = 0xe4, -+ [OFFSET_DEBUGCTRL] = 0xe8, -+ [OFFSET_FIFO_STAT] = 0xf4, -+ [OFFSET_FIFO_THRESH] = 0xf8, -+ [OFFSET_DCM_EN] = 0xf88, -+}; -+ - struct mtk_i2c_compatible { - const struct i2c_adapter_quirks *quirks; - const u16 *regs; -@@ -442,6 +471,19 @@ static const struct mtk_i2c_compatible m - .max_dma_support = 36, - }; - -+static const struct mtk_i2c_compatible mt8188_compat = { -+ .regs = mt_i2c_regs_v3, -+ .pmic_i2c = 0, -+ .dcm = 0, -+ .auto_restart = 1, -+ .aux_len_reg = 1, -+ .timing_adjust = 1, -+ .dma_sync = 0, -+ .ltiming_adjust = 1, -+ .apdma_sync = 1, -+ .max_dma_support = 36, -+}; -+ - static const struct mtk_i2c_compatible mt8192_compat = { - .quirks = &mt8183_i2c_quirks, - .regs = mt_i2c_regs_v2, -@@ -465,6 +507,7 @@ static const struct of_device_id mtk_i2c - { .compatible = "mediatek,mt8173-i2c", .data = &mt8173_compat }, - { .compatible = "mediatek,mt8183-i2c", .data = &mt8183_compat }, - { .compatible = "mediatek,mt8186-i2c", .data = &mt8186_compat }, -+ { .compatible = "mediatek,mt8188-i2c", .data = &mt8188_compat }, - { .compatible = "mediatek,mt8192-i2c", .data = &mt8192_compat }, - {} - }; diff --git a/target/linux/mediatek/patches-5.15/850-v6.0-i2c-move-drivers-from-strlcpy-to-strscpy.patch b/target/linux/mediatek/patches-5.15/850-v6.0-i2c-move-drivers-from-strlcpy-to-strscpy.patch deleted file mode 100644 index 46e92a92f3..0000000000 --- a/target/linux/mediatek/patches-5.15/850-v6.0-i2c-move-drivers-from-strlcpy-to-strscpy.patch +++ /dev/null @@ -1,579 +0,0 @@ -From 2f4ca256a98cc19787b7c861109dd1150a21b0bf Mon Sep 17 00:00:00 2001 -From: Wolfram Sang -Date: Thu, 11 Aug 2022 09:10:30 +0200 -Subject: [PATCH 11/16] i2c: move drivers from strlcpy to strscpy - -Follow the advice of the below link and prefer 'strscpy'. Conversion is -easy because no driver used the return value and has been done with a -simple sed invocation. - -Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/ -Signed-off-by: Wolfram Sang -Signed-off-by: Wolfram Sang ---- - drivers/i2c/busses/i2c-altera.c | 2 +- - drivers/i2c/busses/i2c-aspeed.c | 2 +- - drivers/i2c/busses/i2c-au1550.c | 2 +- - drivers/i2c/busses/i2c-axxia.c | 2 +- - drivers/i2c/busses/i2c-bcm-kona.c | 2 +- - drivers/i2c/busses/i2c-cbus-gpio.c | 2 +- - drivers/i2c/busses/i2c-cht-wc.c | 2 +- - drivers/i2c/busses/i2c-cros-ec-tunnel.c | 2 +- - drivers/i2c/busses/i2c-davinci.c | 2 +- - drivers/i2c/busses/i2c-digicolor.c | 2 +- - drivers/i2c/busses/i2c-eg20t.c | 2 +- - drivers/i2c/busses/i2c-emev2.c | 2 +- - drivers/i2c/busses/i2c-exynos5.c | 2 +- - drivers/i2c/busses/i2c-gpio.c | 2 +- - drivers/i2c/busses/i2c-highlander.c | 2 +- - drivers/i2c/busses/i2c-hix5hd2.c | 2 +- - drivers/i2c/busses/i2c-i801.c | 4 ++-- - drivers/i2c/busses/i2c-ibm_iic.c | 2 +- - drivers/i2c/busses/i2c-icy.c | 2 +- - drivers/i2c/busses/i2c-imx-lpi2c.c | 2 +- - drivers/i2c/busses/i2c-lpc2k.c | 2 +- - drivers/i2c/busses/i2c-meson.c | 2 +- - drivers/i2c/busses/i2c-mt65xx.c | 2 +- - drivers/i2c/busses/i2c-mt7621.c | 2 +- - drivers/i2c/busses/i2c-mv64xxx.c | 2 +- - drivers/i2c/busses/i2c-mxs.c | 2 +- - drivers/i2c/busses/i2c-nvidia-gpu.c | 2 +- - drivers/i2c/busses/i2c-omap.c | 2 +- - drivers/i2c/busses/i2c-opal.c | 4 ++-- - drivers/i2c/busses/i2c-parport.c | 2 +- - drivers/i2c/busses/i2c-pxa.c | 2 +- - drivers/i2c/busses/i2c-qcom-geni.c | 2 +- - drivers/i2c/busses/i2c-qup.c | 2 +- - drivers/i2c/busses/i2c-rcar.c | 2 +- - drivers/i2c/busses/i2c-riic.c | 2 +- - drivers/i2c/busses/i2c-rk3x.c | 2 +- - drivers/i2c/busses/i2c-s3c2410.c | 2 +- - drivers/i2c/busses/i2c-sh_mobile.c | 2 +- - drivers/i2c/busses/i2c-simtec.c | 2 +- - drivers/i2c/busses/i2c-taos-evm.c | 2 +- - drivers/i2c/busses/i2c-tegra-bpmp.c | 2 +- - drivers/i2c/busses/i2c-tegra.c | 2 +- - drivers/i2c/busses/i2c-uniphier-f.c | 2 +- - drivers/i2c/busses/i2c-uniphier.c | 2 +- - drivers/i2c/busses/i2c-versatile.c | 2 +- - drivers/i2c/busses/i2c-wmt.c | 2 +- - 46 files changed, 48 insertions(+), 48 deletions(-) - ---- a/drivers/i2c/busses/i2c-altera.c -+++ b/drivers/i2c/busses/i2c-altera.c -@@ -447,7 +447,7 @@ static int altr_i2c_probe(struct platfor - mutex_unlock(&idev->isr_mutex); - - i2c_set_adapdata(&idev->adapter, idev); -- strlcpy(idev->adapter.name, pdev->name, sizeof(idev->adapter.name)); -+ strscpy(idev->adapter.name, pdev->name, sizeof(idev->adapter.name)); - idev->adapter.owner = THIS_MODULE; - idev->adapter.algo = &altr_i2c_algo; - idev->adapter.dev.parent = &pdev->dev; ---- a/drivers/i2c/busses/i2c-aspeed.c -+++ b/drivers/i2c/busses/i2c-aspeed.c -@@ -1044,7 +1044,7 @@ static int aspeed_i2c_probe_bus(struct p - bus->adap.algo = &aspeed_i2c_algo; - bus->adap.dev.parent = &pdev->dev; - bus->adap.dev.of_node = pdev->dev.of_node; -- strlcpy(bus->adap.name, pdev->name, sizeof(bus->adap.name)); -+ strscpy(bus->adap.name, pdev->name, sizeof(bus->adap.name)); - i2c_set_adapdata(&bus->adap, bus); - - bus->dev = &pdev->dev; ---- a/drivers/i2c/busses/i2c-au1550.c -+++ b/drivers/i2c/busses/i2c-au1550.c -@@ -321,7 +321,7 @@ i2c_au1550_probe(struct platform_device - priv->adap.algo = &au1550_algo; - priv->adap.algo_data = priv; - priv->adap.dev.parent = &pdev->dev; -- strlcpy(priv->adap.name, "Au1xxx PSC I2C", sizeof(priv->adap.name)); -+ strscpy(priv->adap.name, "Au1xxx PSC I2C", sizeof(priv->adap.name)); - - /* Now, set up the PSC for SMBus PIO mode. */ - i2c_au1550_setup(priv); ---- a/drivers/i2c/busses/i2c-axxia.c -+++ b/drivers/i2c/busses/i2c-axxia.c -@@ -783,7 +783,7 @@ static int axxia_i2c_probe(struct platfo - } - - i2c_set_adapdata(&idev->adapter, idev); -- strlcpy(idev->adapter.name, pdev->name, sizeof(idev->adapter.name)); -+ strscpy(idev->adapter.name, pdev->name, sizeof(idev->adapter.name)); - idev->adapter.owner = THIS_MODULE; - idev->adapter.algo = &axxia_i2c_algo; - idev->adapter.bus_recovery_info = &axxia_i2c_recovery_info; ---- a/drivers/i2c/busses/i2c-bcm-kona.c -+++ b/drivers/i2c/busses/i2c-bcm-kona.c -@@ -849,7 +849,7 @@ static int bcm_kona_i2c_probe(struct pla - adap = &dev->adapter; - i2c_set_adapdata(adap, dev); - adap->owner = THIS_MODULE; -- strlcpy(adap->name, "Broadcom I2C adapter", sizeof(adap->name)); -+ strscpy(adap->name, "Broadcom I2C adapter", sizeof(adap->name)); - adap->algo = &bcm_algo; - adap->dev.parent = &pdev->dev; - adap->dev.of_node = pdev->dev.of_node; ---- a/drivers/i2c/busses/i2c-cbus-gpio.c -+++ b/drivers/i2c/busses/i2c-cbus-gpio.c -@@ -245,7 +245,7 @@ static int cbus_i2c_probe(struct platfor - adapter->nr = pdev->id; - adapter->timeout = HZ; - adapter->algo = &cbus_i2c_algo; -- strlcpy(adapter->name, "CBUS I2C adapter", sizeof(adapter->name)); -+ strscpy(adapter->name, "CBUS I2C adapter", sizeof(adapter->name)); - - spin_lock_init(&chost->lock); - chost->dev = &pdev->dev; ---- a/drivers/i2c/busses/i2c-cht-wc.c -+++ b/drivers/i2c/busses/i2c-cht-wc.c -@@ -334,7 +334,7 @@ static int cht_wc_i2c_adap_i2c_probe(str - adap->adapter.class = I2C_CLASS_HWMON; - adap->adapter.algo = &cht_wc_i2c_adap_algo; - adap->adapter.lock_ops = &cht_wc_i2c_adap_lock_ops; -- strlcpy(adap->adapter.name, "PMIC I2C Adapter", -+ strscpy(adap->adapter.name, "PMIC I2C Adapter", - sizeof(adap->adapter.name)); - adap->adapter.dev.parent = &pdev->dev; - ---- a/drivers/i2c/busses/i2c-cros-ec-tunnel.c -+++ b/drivers/i2c/busses/i2c-cros-ec-tunnel.c -@@ -267,7 +267,7 @@ static int ec_i2c_probe(struct platform_ - bus->dev = dev; - - bus->adap.owner = THIS_MODULE; -- strlcpy(bus->adap.name, "cros-ec-i2c-tunnel", sizeof(bus->adap.name)); -+ strscpy(bus->adap.name, "cros-ec-i2c-tunnel", sizeof(bus->adap.name)); - bus->adap.algo = &ec_i2c_algorithm; - bus->adap.algo_data = bus; - bus->adap.dev.parent = &pdev->dev; ---- a/drivers/i2c/busses/i2c-davinci.c -+++ b/drivers/i2c/busses/i2c-davinci.c -@@ -847,7 +847,7 @@ static int davinci_i2c_probe(struct plat - i2c_set_adapdata(adap, dev); - adap->owner = THIS_MODULE; - adap->class = I2C_CLASS_DEPRECATED; -- strlcpy(adap->name, "DaVinci I2C adapter", sizeof(adap->name)); -+ strscpy(adap->name, "DaVinci I2C adapter", sizeof(adap->name)); - adap->algo = &i2c_davinci_algo; - adap->dev.parent = &pdev->dev; - adap->timeout = DAVINCI_I2C_TIMEOUT; ---- a/drivers/i2c/busses/i2c-digicolor.c -+++ b/drivers/i2c/busses/i2c-digicolor.c -@@ -322,7 +322,7 @@ static int dc_i2c_probe(struct platform_ - if (ret < 0) - return ret; - -- strlcpy(i2c->adap.name, "Conexant Digicolor I2C adapter", -+ strscpy(i2c->adap.name, "Conexant Digicolor I2C adapter", - sizeof(i2c->adap.name)); - i2c->adap.owner = THIS_MODULE; - i2c->adap.algo = &dc_i2c_algorithm; ---- a/drivers/i2c/busses/i2c-eg20t.c -+++ b/drivers/i2c/busses/i2c-eg20t.c -@@ -773,7 +773,7 @@ static int pch_i2c_probe(struct pci_dev - - pch_adap->owner = THIS_MODULE; - pch_adap->class = I2C_CLASS_HWMON; -- strlcpy(pch_adap->name, KBUILD_MODNAME, sizeof(pch_adap->name)); -+ strscpy(pch_adap->name, KBUILD_MODNAME, sizeof(pch_adap->name)); - pch_adap->algo = &pch_algorithm; - pch_adap->algo_data = &adap_info->pch_data[i]; - ---- a/drivers/i2c/busses/i2c-emev2.c -+++ b/drivers/i2c/busses/i2c-emev2.c -@@ -371,7 +371,7 @@ static int em_i2c_probe(struct platform_ - if (IS_ERR(priv->base)) - return PTR_ERR(priv->base); - -- strlcpy(priv->adap.name, "EMEV2 I2C", sizeof(priv->adap.name)); -+ strscpy(priv->adap.name, "EMEV2 I2C", sizeof(priv->adap.name)); - - priv->sclk = devm_clk_get(&pdev->dev, "sclk"); - if (IS_ERR(priv->sclk)) ---- a/drivers/i2c/busses/i2c-exynos5.c -+++ b/drivers/i2c/busses/i2c-exynos5.c -@@ -751,7 +751,7 @@ static int exynos5_i2c_probe(struct plat - if (of_property_read_u32(np, "clock-frequency", &i2c->op_clock)) - i2c->op_clock = I2C_MAX_STANDARD_MODE_FREQ; - -- strlcpy(i2c->adap.name, "exynos5-i2c", sizeof(i2c->adap.name)); -+ strscpy(i2c->adap.name, "exynos5-i2c", sizeof(i2c->adap.name)); - i2c->adap.owner = THIS_MODULE; - i2c->adap.algo = &exynos5_i2c_algorithm; - i2c->adap.retries = 3; ---- a/drivers/i2c/busses/i2c-gpio.c -+++ b/drivers/i2c/busses/i2c-gpio.c -@@ -436,7 +436,7 @@ static int i2c_gpio_probe(struct platfor - - adap->owner = THIS_MODULE; - if (np) -- strlcpy(adap->name, dev_name(dev), sizeof(adap->name)); -+ strscpy(adap->name, dev_name(dev), sizeof(adap->name)); - else - snprintf(adap->name, sizeof(adap->name), "i2c-gpio%d", pdev->id); - ---- a/drivers/i2c/busses/i2c-highlander.c -+++ b/drivers/i2c/busses/i2c-highlander.c -@@ -402,7 +402,7 @@ static int highlander_i2c_probe(struct p - i2c_set_adapdata(adap, dev); - adap->owner = THIS_MODULE; - adap->class = I2C_CLASS_HWMON; -- strlcpy(adap->name, "HL FPGA I2C adapter", sizeof(adap->name)); -+ strscpy(adap->name, "HL FPGA I2C adapter", sizeof(adap->name)); - adap->algo = &highlander_i2c_algo; - adap->dev.parent = &pdev->dev; - adap->nr = pdev->id; ---- a/drivers/i2c/busses/i2c-hix5hd2.c -+++ b/drivers/i2c/busses/i2c-hix5hd2.c -@@ -423,7 +423,7 @@ static int hix5hd2_i2c_probe(struct plat - } - clk_prepare_enable(priv->clk); - -- strlcpy(priv->adap.name, "hix5hd2-i2c", sizeof(priv->adap.name)); -+ strscpy(priv->adap.name, "hix5hd2-i2c", sizeof(priv->adap.name)); - priv->dev = &pdev->dev; - priv->adap.owner = THIS_MODULE; - priv->adap.algo = &hix5hd2_i2c_algorithm; ---- a/drivers/i2c/busses/i2c-i801.c -+++ b/drivers/i2c/busses/i2c-i801.c -@@ -1110,7 +1110,7 @@ static void dmi_check_onboard_device(u8 - - memset(&info, 0, sizeof(struct i2c_board_info)); - info.addr = dmi_devices[i].i2c_addr; -- strlcpy(info.type, dmi_devices[i].i2c_type, I2C_NAME_SIZE); -+ strscpy(info.type, dmi_devices[i].i2c_type, I2C_NAME_SIZE); - i2c_new_client_device(adap, &info); - break; - } -@@ -1266,7 +1266,7 @@ static void register_dell_lis3lv02d_i2c_ - - memset(&info, 0, sizeof(struct i2c_board_info)); - info.addr = dell_lis3lv02d_devices[i].i2c_addr; -- strlcpy(info.type, "lis3lv02d", I2C_NAME_SIZE); -+ strscpy(info.type, "lis3lv02d", I2C_NAME_SIZE); - i2c_new_client_device(&priv->adapter, &info); - } - ---- a/drivers/i2c/busses/i2c-ibm_iic.c -+++ b/drivers/i2c/busses/i2c-ibm_iic.c -@@ -736,7 +736,7 @@ static int iic_probe(struct platform_dev - adap = &dev->adap; - adap->dev.parent = &ofdev->dev; - adap->dev.of_node = of_node_get(np); -- strlcpy(adap->name, "IBM IIC", sizeof(adap->name)); -+ strscpy(adap->name, "IBM IIC", sizeof(adap->name)); - i2c_set_adapdata(adap, dev); - adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD; - adap->algo = &iic_algo; ---- a/drivers/i2c/busses/i2c-icy.c -+++ b/drivers/i2c/busses/i2c-icy.c -@@ -141,7 +141,7 @@ static int icy_probe(struct zorro_dev *z - i2c->adapter.owner = THIS_MODULE; - /* i2c->adapter.algo assigned by i2c_pcf_add_bus() */ - i2c->adapter.algo_data = algo_data; -- strlcpy(i2c->adapter.name, "ICY I2C Zorro adapter", -+ strscpy(i2c->adapter.name, "ICY I2C Zorro adapter", - sizeof(i2c->adapter.name)); - - if (!devm_request_mem_region(&z->dev, ---- a/drivers/i2c/busses/i2c-imx-lpi2c.c -+++ b/drivers/i2c/busses/i2c-imx-lpi2c.c -@@ -564,7 +564,7 @@ static int lpi2c_imx_probe(struct platfo - lpi2c_imx->adapter.algo = &lpi2c_imx_algo; - lpi2c_imx->adapter.dev.parent = &pdev->dev; - lpi2c_imx->adapter.dev.of_node = pdev->dev.of_node; -- strlcpy(lpi2c_imx->adapter.name, pdev->name, -+ strscpy(lpi2c_imx->adapter.name, pdev->name, - sizeof(lpi2c_imx->adapter.name)); - - lpi2c_imx->clk = devm_clk_get(&pdev->dev, NULL); ---- a/drivers/i2c/busses/i2c-lpc2k.c -+++ b/drivers/i2c/busses/i2c-lpc2k.c -@@ -417,7 +417,7 @@ static int i2c_lpc2k_probe(struct platfo - - i2c_set_adapdata(&i2c->adap, i2c); - i2c->adap.owner = THIS_MODULE; -- strlcpy(i2c->adap.name, "LPC2K I2C adapter", sizeof(i2c->adap.name)); -+ strscpy(i2c->adap.name, "LPC2K I2C adapter", sizeof(i2c->adap.name)); - i2c->adap.algo = &i2c_lpc2k_algorithm; - i2c->adap.dev.parent = &pdev->dev; - i2c->adap.dev.of_node = pdev->dev.of_node; ---- a/drivers/i2c/busses/i2c-meson.c -+++ b/drivers/i2c/busses/i2c-meson.c -@@ -451,7 +451,7 @@ static int meson_i2c_probe(struct platfo - return ret; - } - -- strlcpy(i2c->adap.name, "Meson I2C adapter", -+ strscpy(i2c->adap.name, "Meson I2C adapter", - sizeof(i2c->adap.name)); - i2c->adap.owner = THIS_MODULE; - i2c->adap.algo = &meson_i2c_algorithm; ---- a/drivers/i2c/busses/i2c-mt65xx.c -+++ b/drivers/i2c/busses/i2c-mt65xx.c -@@ -1432,7 +1432,7 @@ static int mtk_i2c_probe(struct platform - speed_clk = I2C_MT65XX_CLK_MAIN; - } - -- strlcpy(i2c->adap.name, I2C_DRV_NAME, sizeof(i2c->adap.name)); -+ strscpy(i2c->adap.name, I2C_DRV_NAME, sizeof(i2c->adap.name)); - - ret = mtk_i2c_set_speed(i2c, clk_get_rate(i2c->clocks[speed_clk].clk)); - if (ret) { ---- a/drivers/i2c/busses/i2c-mt7621.c -+++ b/drivers/i2c/busses/i2c-mt7621.c -@@ -315,7 +315,7 @@ static int mtk_i2c_probe(struct platform - adap->dev.parent = &pdev->dev; - i2c_set_adapdata(adap, i2c); - adap->dev.of_node = pdev->dev.of_node; -- strlcpy(adap->name, dev_name(&pdev->dev), sizeof(adap->name)); -+ strscpy(adap->name, dev_name(&pdev->dev), sizeof(adap->name)); - - platform_set_drvdata(pdev, i2c); - ---- a/drivers/i2c/busses/i2c-mv64xxx.c -+++ b/drivers/i2c/busses/i2c-mv64xxx.c -@@ -1000,7 +1000,7 @@ mv64xxx_i2c_probe(struct platform_device - if (IS_ERR(drv_data->reg_base)) - return PTR_ERR(drv_data->reg_base); - -- strlcpy(drv_data->adapter.name, MV64XXX_I2C_CTLR_NAME " adapter", -+ strscpy(drv_data->adapter.name, MV64XXX_I2C_CTLR_NAME " adapter", - sizeof(drv_data->adapter.name)); - - init_waitqueue_head(&drv_data->waitq); ---- a/drivers/i2c/busses/i2c-mxs.c -+++ b/drivers/i2c/busses/i2c-mxs.c -@@ -838,7 +838,7 @@ static int mxs_i2c_probe(struct platform - return err; - - adap = &i2c->adapter; -- strlcpy(adap->name, "MXS I2C adapter", sizeof(adap->name)); -+ strscpy(adap->name, "MXS I2C adapter", sizeof(adap->name)); - adap->owner = THIS_MODULE; - adap->algo = &mxs_i2c_algo; - adap->quirks = &mxs_i2c_quirks; ---- a/drivers/i2c/busses/i2c-nvidia-gpu.c -+++ b/drivers/i2c/busses/i2c-nvidia-gpu.c -@@ -319,7 +319,7 @@ static int gpu_i2c_probe(struct pci_dev - - i2c_set_adapdata(&i2cd->adapter, i2cd); - i2cd->adapter.owner = THIS_MODULE; -- strlcpy(i2cd->adapter.name, "NVIDIA GPU I2C adapter", -+ strscpy(i2cd->adapter.name, "NVIDIA GPU I2C adapter", - sizeof(i2cd->adapter.name)); - i2cd->adapter.algo = &gpu_i2c_algorithm; - i2cd->adapter.quirks = &gpu_i2c_quirks; ---- a/drivers/i2c/busses/i2c-omap.c -+++ b/drivers/i2c/busses/i2c-omap.c -@@ -1488,7 +1488,7 @@ omap_i2c_probe(struct platform_device *p - i2c_set_adapdata(adap, omap); - adap->owner = THIS_MODULE; - adap->class = I2C_CLASS_DEPRECATED; -- strlcpy(adap->name, "OMAP I2C adapter", sizeof(adap->name)); -+ strscpy(adap->name, "OMAP I2C adapter", sizeof(adap->name)); - adap->algo = &omap_i2c_algo; - adap->quirks = &omap_i2c_quirks; - adap->dev.parent = &pdev->dev; ---- a/drivers/i2c/busses/i2c-opal.c -+++ b/drivers/i2c/busses/i2c-opal.c -@@ -220,9 +220,9 @@ static int i2c_opal_probe(struct platfor - adapter->dev.of_node = of_node_get(pdev->dev.of_node); - pname = of_get_property(pdev->dev.of_node, "ibm,port-name", NULL); - if (pname) -- strlcpy(adapter->name, pname, sizeof(adapter->name)); -+ strscpy(adapter->name, pname, sizeof(adapter->name)); - else -- strlcpy(adapter->name, "opal", sizeof(adapter->name)); -+ strscpy(adapter->name, "opal", sizeof(adapter->name)); - - platform_set_drvdata(pdev, adapter); - rc = i2c_add_adapter(adapter); ---- a/drivers/i2c/busses/i2c-parport.c -+++ b/drivers/i2c/busses/i2c-parport.c -@@ -308,7 +308,7 @@ static void i2c_parport_attach(struct pa - /* Fill the rest of the structure */ - adapter->adapter.owner = THIS_MODULE; - adapter->adapter.class = I2C_CLASS_HWMON; -- strlcpy(adapter->adapter.name, "Parallel port adapter", -+ strscpy(adapter->adapter.name, "Parallel port adapter", - sizeof(adapter->adapter.name)); - adapter->algo_data = parport_algo_data; - /* Slow down if we can't sense SCL */ ---- a/drivers/i2c/busses/i2c-pxa.c -+++ b/drivers/i2c/busses/i2c-pxa.c -@@ -1463,7 +1463,7 @@ static int i2c_pxa_probe(struct platform - spin_lock_init(&i2c->lock); - init_waitqueue_head(&i2c->wait); - -- strlcpy(i2c->adap.name, "pxa_i2c-i2c", sizeof(i2c->adap.name)); -+ strscpy(i2c->adap.name, "pxa_i2c-i2c", sizeof(i2c->adap.name)); - - i2c->clk = devm_clk_get(&dev->dev, NULL); - if (IS_ERR(i2c->clk)) { ---- a/drivers/i2c/busses/i2c-qcom-geni.c -+++ b/drivers/i2c/busses/i2c-qcom-geni.c -@@ -577,7 +577,7 @@ static int geni_i2c_probe(struct platfor - i2c_set_adapdata(&gi2c->adap, gi2c); - gi2c->adap.dev.parent = dev; - gi2c->adap.dev.of_node = dev->of_node; -- strlcpy(gi2c->adap.name, "Geni-I2C", sizeof(gi2c->adap.name)); -+ strscpy(gi2c->adap.name, "Geni-I2C", sizeof(gi2c->adap.name)); - - ret = geni_icc_get(&gi2c->se, "qup-memory"); - if (ret) ---- a/drivers/i2c/busses/i2c-qup.c -+++ b/drivers/i2c/busses/i2c-qup.c -@@ -1885,7 +1885,7 @@ nodma: - qup->adap.dev.of_node = pdev->dev.of_node; - qup->is_last = true; - -- strlcpy(qup->adap.name, "QUP I2C adapter", sizeof(qup->adap.name)); -+ strscpy(qup->adap.name, "QUP I2C adapter", sizeof(qup->adap.name)); - - pm_runtime_set_autosuspend_delay(qup->dev, MSEC_PER_SEC); - pm_runtime_use_autosuspend(qup->dev); ---- a/drivers/i2c/busses/i2c-rcar.c -+++ b/drivers/i2c/busses/i2c-rcar.c -@@ -1059,7 +1059,7 @@ static int rcar_i2c_probe(struct platfor - adap->bus_recovery_info = &rcar_i2c_bri; - adap->quirks = &rcar_i2c_quirks; - i2c_set_adapdata(adap, priv); -- strlcpy(adap->name, pdev->name, sizeof(adap->name)); -+ strscpy(adap->name, pdev->name, sizeof(adap->name)); - - /* Init DMA */ - sg_init_table(&priv->sg, 1); ---- a/drivers/i2c/busses/i2c-riic.c -+++ b/drivers/i2c/busses/i2c-riic.c -@@ -447,7 +447,7 @@ static int riic_i2c_probe(struct platfor - - adap = &riic->adapter; - i2c_set_adapdata(adap, riic); -- strlcpy(adap->name, "Renesas RIIC adapter", sizeof(adap->name)); -+ strscpy(adap->name, "Renesas RIIC adapter", sizeof(adap->name)); - adap->owner = THIS_MODULE; - adap->algo = &riic_algo; - adap->dev.parent = &pdev->dev; ---- a/drivers/i2c/busses/i2c-rk3x.c -+++ b/drivers/i2c/busses/i2c-rk3x.c -@@ -1247,7 +1247,7 @@ static int rk3x_i2c_probe(struct platfor - /* use common interface to get I2C timing properties */ - i2c_parse_fw_timings(&pdev->dev, &i2c->t, true); - -- strlcpy(i2c->adap.name, "rk3x-i2c", sizeof(i2c->adap.name)); -+ strscpy(i2c->adap.name, "rk3x-i2c", sizeof(i2c->adap.name)); - i2c->adap.owner = THIS_MODULE; - i2c->adap.algo = &rk3x_i2c_algorithm; - i2c->adap.retries = 3; ---- a/drivers/i2c/busses/i2c-s3c2410.c -+++ b/drivers/i2c/busses/i2c-s3c2410.c -@@ -1078,7 +1078,7 @@ static int s3c24xx_i2c_probe(struct plat - else - s3c24xx_i2c_parse_dt(pdev->dev.of_node, i2c); - -- strlcpy(i2c->adap.name, "s3c2410-i2c", sizeof(i2c->adap.name)); -+ strscpy(i2c->adap.name, "s3c2410-i2c", sizeof(i2c->adap.name)); - i2c->adap.owner = THIS_MODULE; - i2c->adap.algo = &s3c24xx_i2c_algorithm; - i2c->adap.retries = 2; ---- a/drivers/i2c/busses/i2c-sh_mobile.c -+++ b/drivers/i2c/busses/i2c-sh_mobile.c -@@ -930,7 +930,7 @@ static int sh_mobile_i2c_probe(struct pl - adap->nr = dev->id; - adap->dev.of_node = dev->dev.of_node; - -- strlcpy(adap->name, dev->name, sizeof(adap->name)); -+ strscpy(adap->name, dev->name, sizeof(adap->name)); - - spin_lock_init(&pd->lock); - init_waitqueue_head(&pd->wait); ---- a/drivers/i2c/busses/i2c-simtec.c -+++ b/drivers/i2c/busses/i2c-simtec.c -@@ -99,7 +99,7 @@ static int simtec_i2c_probe(struct platf - pd->adap.algo_data = &pd->bit; - pd->adap.dev.parent = &dev->dev; - -- strlcpy(pd->adap.name, "Simtec I2C", sizeof(pd->adap.name)); -+ strscpy(pd->adap.name, "Simtec I2C", sizeof(pd->adap.name)); - - pd->bit.data = pd; - pd->bit.setsda = simtec_i2c_setsda; ---- a/drivers/i2c/busses/i2c-taos-evm.c -+++ b/drivers/i2c/busses/i2c-taos-evm.c -@@ -239,7 +239,7 @@ static int taos_connect(struct serio *se - dev_err(&serio->dev, "TAOS EVM identification failed\n"); - goto exit_close; - } -- strlcpy(adapter->name, name, sizeof(adapter->name)); -+ strscpy(adapter->name, name, sizeof(adapter->name)); - - /* Turn echo off for better performance */ - taos->state = TAOS_STATE_EOFF; ---- a/drivers/i2c/busses/i2c-tegra-bpmp.c -+++ b/drivers/i2c/busses/i2c-tegra-bpmp.c -@@ -305,7 +305,7 @@ static int tegra_bpmp_i2c_probe(struct p - - i2c_set_adapdata(&i2c->adapter, i2c); - i2c->adapter.owner = THIS_MODULE; -- strlcpy(i2c->adapter.name, "Tegra BPMP I2C adapter", -+ strscpy(i2c->adapter.name, "Tegra BPMP I2C adapter", - sizeof(i2c->adapter.name)); - i2c->adapter.algo = &tegra_bpmp_i2c_algo; - i2c->adapter.dev.parent = &pdev->dev; ---- a/drivers/i2c/busses/i2c-tegra.c -+++ b/drivers/i2c/busses/i2c-tegra.c -@@ -1799,7 +1799,7 @@ static int tegra_i2c_probe(struct platfo - if (i2c_dev->hw->supports_bus_clear) - i2c_dev->adapter.bus_recovery_info = &tegra_i2c_recovery_info; - -- strlcpy(i2c_dev->adapter.name, dev_name(i2c_dev->dev), -+ strscpy(i2c_dev->adapter.name, dev_name(i2c_dev->dev), - sizeof(i2c_dev->adapter.name)); - - err = i2c_add_numbered_adapter(&i2c_dev->adapter); ---- a/drivers/i2c/busses/i2c-uniphier-f.c -+++ b/drivers/i2c/busses/i2c-uniphier-f.c -@@ -564,7 +564,7 @@ static int uniphier_fi2c_probe(struct pl - priv->adap.algo = &uniphier_fi2c_algo; - priv->adap.dev.parent = dev; - priv->adap.dev.of_node = dev->of_node; -- strlcpy(priv->adap.name, "UniPhier FI2C", sizeof(priv->adap.name)); -+ strscpy(priv->adap.name, "UniPhier FI2C", sizeof(priv->adap.name)); - priv->adap.bus_recovery_info = &uniphier_fi2c_bus_recovery_info; - i2c_set_adapdata(&priv->adap, priv); - platform_set_drvdata(pdev, priv); ---- a/drivers/i2c/busses/i2c-uniphier.c -+++ b/drivers/i2c/busses/i2c-uniphier.c -@@ -358,7 +358,7 @@ static int uniphier_i2c_probe(struct pla - priv->adap.algo = &uniphier_i2c_algo; - priv->adap.dev.parent = dev; - priv->adap.dev.of_node = dev->of_node; -- strlcpy(priv->adap.name, "UniPhier I2C", sizeof(priv->adap.name)); -+ strscpy(priv->adap.name, "UniPhier I2C", sizeof(priv->adap.name)); - priv->adap.bus_recovery_info = &uniphier_i2c_bus_recovery_info; - i2c_set_adapdata(&priv->adap, priv); - platform_set_drvdata(pdev, priv); ---- a/drivers/i2c/busses/i2c-versatile.c -+++ b/drivers/i2c/busses/i2c-versatile.c -@@ -79,7 +79,7 @@ static int i2c_versatile_probe(struct pl - writel(SCL | SDA, i2c->base + I2C_CONTROLS); - - i2c->adap.owner = THIS_MODULE; -- strlcpy(i2c->adap.name, "Versatile I2C adapter", sizeof(i2c->adap.name)); -+ strscpy(i2c->adap.name, "Versatile I2C adapter", sizeof(i2c->adap.name)); - i2c->adap.algo_data = &i2c->algo; - i2c->adap.dev.parent = &dev->dev; - i2c->adap.dev.of_node = dev->dev.of_node; ---- a/drivers/i2c/busses/i2c-wmt.c -+++ b/drivers/i2c/busses/i2c-wmt.c -@@ -413,7 +413,7 @@ static int wmt_i2c_probe(struct platform - - adap = &i2c_dev->adapter; - i2c_set_adapdata(adap, i2c_dev); -- strlcpy(adap->name, "WMT I2C adapter", sizeof(adap->name)); -+ strscpy(adap->name, "WMT I2C adapter", sizeof(adap->name)); - adap->owner = THIS_MODULE; - adap->algo = &wmt_i2c_algo; - adap->dev.parent = &pdev->dev; diff --git a/target/linux/mediatek/patches-5.15/851-v6.2-i2c-mediatek-add-mt7986-support.patch b/target/linux/mediatek/patches-5.15/851-v6.2-i2c-mediatek-add-mt7986-support.patch deleted file mode 100644 index 4c398c59f9..0000000000 --- a/target/linux/mediatek/patches-5.15/851-v6.2-i2c-mediatek-add-mt7986-support.patch +++ /dev/null @@ -1,44 +0,0 @@ -From 11f9a0f4e51887ad7b4a2898a368fcd0c2984e89 Mon Sep 17 00:00:00 2001 -From: Frank Wunderlich -Date: Sun, 9 Oct 2022 12:16:31 +0200 -Subject: [PATCH 12/16] i2c: mediatek: add mt7986 support - -Add i2c support for MT7986 SoC. - -Signed-off-by: Frank Wunderlich -Reviewed-by: AngeloGioacchino Del Regno -Signed-off-by: Wolfram Sang ---- - drivers/i2c/busses/i2c-mt65xx.c | 14 ++++++++++++++ - 1 file changed, 14 insertions(+) - ---- a/drivers/i2c/busses/i2c-mt65xx.c -+++ b/drivers/i2c/busses/i2c-mt65xx.c -@@ -431,6 +431,19 @@ static const struct mtk_i2c_compatible m - .max_dma_support = 33, - }; - -+static const struct mtk_i2c_compatible mt7986_compat = { -+ .quirks = &mt7622_i2c_quirks, -+ .regs = mt_i2c_regs_v1, -+ .pmic_i2c = 0, -+ .dcm = 1, -+ .auto_restart = 1, -+ .aux_len_reg = 1, -+ .timing_adjust = 0, -+ .dma_sync = 1, -+ .ltiming_adjust = 0, -+ .max_dma_support = 32, -+}; -+ - static const struct mtk_i2c_compatible mt8173_compat = { - .regs = mt_i2c_regs_v1, - .pmic_i2c = 0, -@@ -503,6 +516,7 @@ static const struct of_device_id mtk_i2c - { .compatible = "mediatek,mt6577-i2c", .data = &mt6577_compat }, - { .compatible = "mediatek,mt6589-i2c", .data = &mt6589_compat }, - { .compatible = "mediatek,mt7622-i2c", .data = &mt7622_compat }, -+ { .compatible = "mediatek,mt7986-i2c", .data = &mt7986_compat }, - { .compatible = "mediatek,mt8168-i2c", .data = &mt8168_compat }, - { .compatible = "mediatek,mt8173-i2c", .data = &mt8173_compat }, - { .compatible = "mediatek,mt8183-i2c", .data = &mt8183_compat }, diff --git a/target/linux/mediatek/patches-5.15/852-v6.3-i2c-mt65xx-Use-devm_platform_get_and_ioremap_resourc.patch b/target/linux/mediatek/patches-5.15/852-v6.3-i2c-mt65xx-Use-devm_platform_get_and_ioremap_resourc.patch deleted file mode 100644 index 18c66cdac5..0000000000 --- a/target/linux/mediatek/patches-5.15/852-v6.3-i2c-mt65xx-Use-devm_platform_get_and_ioremap_resourc.patch +++ /dev/null @@ -1,42 +0,0 @@ -From 98204ccafd45a8a6109ff2d60e2c179b95d92578 Mon Sep 17 00:00:00 2001 -From: ye xingchen -Date: Thu, 19 Jan 2023 17:19:58 +0800 -Subject: [PATCH 13/16] i2c: mt65xx: Use - devm_platform_get_and_ioremap_resource() - -Convert platform_get_resource(), devm_ioremap_resource() to a single -call to devm_platform_get_and_ioremap_resource(), as this is exactly -what this function does. - -Signed-off-by: ye xingchen -Reviewed-by: AngeloGioacchino Del Regno -Signed-off-by: Wolfram Sang ---- - drivers/i2c/busses/i2c-mt65xx.c | 7 ++----- - 1 file changed, 2 insertions(+), 5 deletions(-) - ---- a/drivers/i2c/busses/i2c-mt65xx.c -+++ b/drivers/i2c/busses/i2c-mt65xx.c -@@ -1366,20 +1366,17 @@ static int mtk_i2c_probe(struct platform - { - int ret = 0; - struct mtk_i2c *i2c; -- struct resource *res; - int i, irq, speed_clk; - - i2c = devm_kzalloc(&pdev->dev, sizeof(*i2c), GFP_KERNEL); - if (!i2c) - return -ENOMEM; - -- res = platform_get_resource(pdev, IORESOURCE_MEM, 0); -- i2c->base = devm_ioremap_resource(&pdev->dev, res); -+ i2c->base = devm_platform_get_and_ioremap_resource(pdev, 0, NULL); - if (IS_ERR(i2c->base)) - return PTR_ERR(i2c->base); - -- res = platform_get_resource(pdev, IORESOURCE_MEM, 1); -- i2c->pdmabase = devm_ioremap_resource(&pdev->dev, res); -+ i2c->pdmabase = devm_platform_get_and_ioremap_resource(pdev, 1, NULL); - if (IS_ERR(i2c->pdmabase)) - return PTR_ERR(i2c->pdmabase); - diff --git a/target/linux/mediatek/patches-5.15/853-v6.3-i2c-mt65xx-drop-of_match_ptr-for-ID-table.patch b/target/linux/mediatek/patches-5.15/853-v6.3-i2c-mt65xx-drop-of_match_ptr-for-ID-table.patch deleted file mode 100644 index d000d53522..0000000000 --- a/target/linux/mediatek/patches-5.15/853-v6.3-i2c-mt65xx-drop-of_match_ptr-for-ID-table.patch +++ /dev/null @@ -1,33 +0,0 @@ -From 8106fa2e0ae6082833fe1df97829c46c0183eaea Mon Sep 17 00:00:00 2001 -From: Krzysztof Kozlowski -Date: Sat, 11 Mar 2023 12:16:54 +0100 -Subject: [PATCH 14/16] i2c: mt65xx: drop of_match_ptr for ID table -MIME-Version: 1.0 -Content-Type: text/plain; charset=UTF-8 -Content-Transfer-Encoding: 8bit - -The driver can match only via the DT table so the table should be always -used and the of_match_ptr does not have any sense (this also allows ACPI -matching via PRP0001, even though it might not be relevant here). - - drivers/i2c/busses/i2c-mt65xx.c:514:34: error: ‘mtk_i2c_of_match’ defined but not used [-Werror=unused-const-variable=] - -Signed-off-by: Krzysztof Kozlowski -Reviewed-by: Guenter Roeck -Reviewed-by: AngeloGioacchino Del Regno -Signed-off-by: Wolfram Sang ---- - drivers/i2c/busses/i2c-mt65xx.c | 2 +- - 1 file changed, 1 insertion(+), 1 deletion(-) - ---- a/drivers/i2c/busses/i2c-mt65xx.c -+++ b/drivers/i2c/busses/i2c-mt65xx.c -@@ -1546,7 +1546,7 @@ static struct platform_driver mtk_i2c_dr - .driver = { - .name = I2C_DRV_NAME, - .pm = &mtk_i2c_pm, -- .of_match_table = of_match_ptr(mtk_i2c_of_match), -+ .of_match_table = mtk_i2c_of_match, - }, - }; - diff --git a/target/linux/mediatek/patches-5.15/854-v6.4-i2c-mediatek-add-support-for-MT7981-SoC.patch b/target/linux/mediatek/patches-5.15/854-v6.4-i2c-mediatek-add-support-for-MT7981-SoC.patch deleted file mode 100644 index e0973741e2..0000000000 --- a/target/linux/mediatek/patches-5.15/854-v6.4-i2c-mediatek-add-support-for-MT7981-SoC.patch +++ /dev/null @@ -1,47 +0,0 @@ -From f69f3d662ba3bf999c36d9ac1e684540c4487bc3 Mon Sep 17 00:00:00 2001 -From: Daniel Golle -Date: Mon, 10 Apr 2023 17:19:38 +0100 -Subject: [PATCH 15/16] i2c: mediatek: add support for MT7981 SoC - -Add support for the I2C units found in the MediaTek MT7981 and MT7988 -SoCs. Just like other recent MediaTek I2C units that also uses v3 -register offsets (which differ from v2 only by OFFSET_SLAVE_ADDR being -0x94 instead of 0x4). - -Signed-off-by: Daniel Golle -Reviewed-by: AngeloGioacchino Del Regno -Reviewed-by: Alexandre Mergnat -Signed-off-by: Wolfram Sang ---- - drivers/i2c/busses/i2c-mt65xx.c | 13 +++++++++++++ - 1 file changed, 13 insertions(+) - ---- a/drivers/i2c/busses/i2c-mt65xx.c -+++ b/drivers/i2c/busses/i2c-mt65xx.c -@@ -431,6 +431,18 @@ static const struct mtk_i2c_compatible m - .max_dma_support = 33, - }; - -+static const struct mtk_i2c_compatible mt7981_compat = { -+ .regs = mt_i2c_regs_v3, -+ .pmic_i2c = 0, -+ .dcm = 0, -+ .auto_restart = 1, -+ .aux_len_reg = 1, -+ .timing_adjust = 1, -+ .dma_sync = 1, -+ .ltiming_adjust = 1, -+ .max_dma_support = 33 -+}; -+ - static const struct mtk_i2c_compatible mt7986_compat = { - .quirks = &mt7622_i2c_quirks, - .regs = mt_i2c_regs_v1, -@@ -516,6 +528,7 @@ static const struct of_device_id mtk_i2c - { .compatible = "mediatek,mt6577-i2c", .data = &mt6577_compat }, - { .compatible = "mediatek,mt6589-i2c", .data = &mt6589_compat }, - { .compatible = "mediatek,mt7622-i2c", .data = &mt7622_compat }, -+ { .compatible = "mediatek,mt7981-i2c", .data = &mt7981_compat }, - { .compatible = "mediatek,mt7986-i2c", .data = &mt7986_compat }, - { .compatible = "mediatek,mt8168-i2c", .data = &mt8168_compat }, - { .compatible = "mediatek,mt8173-i2c", .data = &mt8173_compat }, diff --git a/target/linux/mediatek/patches-5.15/855-i2c-mt65xx-allow-optional-pmic-clock.patch b/target/linux/mediatek/patches-5.15/855-i2c-mt65xx-allow-optional-pmic-clock.patch deleted file mode 100644 index 69cc155d8d..0000000000 --- a/target/linux/mediatek/patches-5.15/855-i2c-mt65xx-allow-optional-pmic-clock.patch +++ /dev/null @@ -1,45 +0,0 @@ -From 3bf827929a44c17bfb1bf1000b143c02ce26a929 Mon Sep 17 00:00:00 2001 -From: Daniel Golle -Date: Sat, 26 Aug 2023 21:56:51 +0100 -Subject: [PATCH] i2c: mt65xx: allow optional pmic clock - -Using the I2C host controller on the MT7981 SoC requires 4 clocks to -be enabled. One of them, the pmic clk, is only enabled in case -'mediatek,have-pmic' is also set which has other consequences which -are not desired in this case. - -Allow defining a pmic clk even in case the 'mediatek,have-pmic' propterty -is not present and the bus is not used to connect to a pmic, but may -still require to enable the pmic clock. - -Signed-off-by: Daniel Golle ---- - drivers/i2c/busses/i2c-mt65xx.c | 12 ++++++++---- - 1 file changed, 8 insertions(+), 4 deletions(-) - ---- a/drivers/i2c/busses/i2c-mt65xx.c -+++ b/drivers/i2c/busses/i2c-mt65xx.c -@@ -1444,15 +1444,19 @@ static int mtk_i2c_probe(struct platform - if (IS_ERR(i2c->clocks[I2C_MT65XX_CLK_ARB].clk)) - return PTR_ERR(i2c->clocks[I2C_MT65XX_CLK_ARB].clk); - -+ i2c->clocks[I2C_MT65XX_CLK_PMIC].clk = devm_clk_get_optional(&pdev->dev, "pmic"); -+ if (IS_ERR(i2c->clocks[I2C_MT65XX_CLK_PMIC].clk)) { -+ dev_err(&pdev->dev, "cannot get pmic clock\n"); -+ return PTR_ERR(i2c->clocks[I2C_MT65XX_CLK_PMIC].clk); -+ } -+ - if (i2c->have_pmic) { -- i2c->clocks[I2C_MT65XX_CLK_PMIC].clk = devm_clk_get(&pdev->dev, "pmic"); -- if (IS_ERR(i2c->clocks[I2C_MT65XX_CLK_PMIC].clk)) { -+ if (!i2c->clocks[I2C_MT65XX_CLK_PMIC].clk) { - dev_err(&pdev->dev, "cannot get pmic clock\n"); -- return PTR_ERR(i2c->clocks[I2C_MT65XX_CLK_PMIC].clk); -+ return -ENODEV; - } - speed_clk = I2C_MT65XX_CLK_PMIC; - } else { -- i2c->clocks[I2C_MT65XX_CLK_PMIC].clk = NULL; - speed_clk = I2C_MT65XX_CLK_MAIN; - } - diff --git a/target/linux/mediatek/patches-5.15/860-v6.6-01-ASoC-mediatek-mt7986-add-common-header.patch b/target/linux/mediatek/patches-5.15/860-v6.6-01-ASoC-mediatek-mt7986-add-common-header.patch deleted file mode 100644 index 9607eec821..0000000000 --- a/target/linux/mediatek/patches-5.15/860-v6.6-01-ASoC-mediatek-mt7986-add-common-header.patch +++ /dev/null @@ -1,269 +0,0 @@ -From d35469096915f2551ed1d26da1ab12ff500fc963 Mon Sep 17 00:00:00 2001 -From: Maso Huang -Date: Thu, 17 Aug 2023 18:13:33 +0800 -Subject: [PATCH 1/9] ASoC: mediatek: mt7986: add common header - -Add header files for register definition and structure. - -Signed-off-by: Maso Huang -Reviewed-by: AngeloGioacchino Del Regno -Link: https://lore.kernel.org/r/20230817101338.18782-2-maso.huang@mediatek.com -Signed-off-by: Mark Brown ---- - sound/soc/mediatek/mt7986/mt7986-afe-common.h | 49 +++++ - sound/soc/mediatek/mt7986/mt7986-reg.h | 196 ++++++++++++++++++ - 2 files changed, 245 insertions(+) - create mode 100644 sound/soc/mediatek/mt7986/mt7986-afe-common.h - create mode 100644 sound/soc/mediatek/mt7986/mt7986-reg.h - ---- /dev/null -+++ b/sound/soc/mediatek/mt7986/mt7986-afe-common.h -@@ -0,0 +1,49 @@ -+/* SPDX-License-Identifier: GPL-2.0 */ -+/* -+ * mt7986-afe-common.h -- MediaTek 7986 audio driver definitions -+ * -+ * Copyright (c) 2023 MediaTek Inc. -+ * Authors: Vic Wu -+ * Maso Huang -+ */ -+ -+#ifndef _MT_7986_AFE_COMMON_H_ -+#define _MT_7986_AFE_COMMON_H_ -+ -+#include -+#include -+#include -+#include -+#include "../common/mtk-base-afe.h" -+ -+enum { -+ MT7986_MEMIF_DL1, -+ MT7986_MEMIF_VUL12, -+ MT7986_MEMIF_NUM, -+ MT7986_DAI_ETDM = MT7986_MEMIF_NUM, -+ MT7986_DAI_NUM, -+}; -+ -+enum { -+ MT7986_IRQ_0, -+ MT7986_IRQ_1, -+ MT7986_IRQ_2, -+ MT7986_IRQ_NUM, -+}; -+ -+struct mt7986_afe_private { -+ struct clk_bulk_data *clks; -+ int num_clks; -+ -+ int pm_runtime_bypass_reg_ctl; -+ -+ /* dai */ -+ void *dai_priv[MT7986_DAI_NUM]; -+}; -+ -+unsigned int mt7986_afe_rate_transform(struct device *dev, -+ unsigned int rate); -+ -+/* dai register */ -+int mt7986_dai_etdm_register(struct mtk_base_afe *afe); -+#endif ---- /dev/null -+++ b/sound/soc/mediatek/mt7986/mt7986-reg.h -@@ -0,0 +1,196 @@ -+/* SPDX-License-Identifier: GPL-2.0 */ -+/* -+ * mt7986-reg.h -- MediaTek 7986 audio driver reg definition -+ * -+ * Copyright (c) 2023 MediaTek Inc. -+ * Authors: Vic Wu -+ * Maso Huang -+ */ -+ -+#ifndef _MT7986_REG_H_ -+#define _MT7986_REG_H_ -+ -+#define AUDIO_TOP_CON2 0x0008 -+#define AUDIO_TOP_CON4 0x0010 -+#define AUDIO_ENGEN_CON0 0x0014 -+#define AFE_IRQ_MCU_EN 0x0100 -+#define AFE_IRQ_MCU_STATUS 0x0120 -+#define AFE_IRQ_MCU_CLR 0x0128 -+#define AFE_IRQ0_MCU_CFG0 0x0140 -+#define AFE_IRQ0_MCU_CFG1 0x0144 -+#define AFE_IRQ1_MCU_CFG0 0x0148 -+#define AFE_IRQ1_MCU_CFG1 0x014c -+#define AFE_IRQ2_MCU_CFG0 0x0150 -+#define AFE_IRQ2_MCU_CFG1 0x0154 -+#define ETDM_IN5_CON0 0x13f0 -+#define ETDM_IN5_CON1 0x13f4 -+#define ETDM_IN5_CON2 0x13f8 -+#define ETDM_IN5_CON3 0x13fc -+#define ETDM_IN5_CON4 0x1400 -+#define ETDM_OUT5_CON0 0x1570 -+#define ETDM_OUT5_CON4 0x1580 -+#define ETDM_OUT5_CON5 0x1584 -+#define ETDM_4_7_COWORK_CON0 0x15e0 -+#define ETDM_4_7_COWORK_CON1 0x15e4 -+#define AFE_CONN018_1 0x1b44 -+#define AFE_CONN018_4 0x1b50 -+#define AFE_CONN019_1 0x1b64 -+#define AFE_CONN019_4 0x1b70 -+#define AFE_CONN124_1 0x2884 -+#define AFE_CONN124_4 0x2890 -+#define AFE_CONN125_1 0x28a4 -+#define AFE_CONN125_4 0x28b0 -+#define AFE_CONN_RS_0 0x3920 -+#define AFE_CONN_RS_3 0x392c -+#define AFE_CONN_16BIT_0 0x3960 -+#define AFE_CONN_16BIT_3 0x396c -+#define AFE_CONN_24BIT_0 0x3980 -+#define AFE_CONN_24BIT_3 0x398c -+#define AFE_MEMIF_CON0 0x3d98 -+#define AFE_MEMIF_RD_MON 0x3da0 -+#define AFE_MEMIF_WR_MON 0x3da4 -+#define AFE_DL0_BASE_MSB 0x3e40 -+#define AFE_DL0_BASE 0x3e44 -+#define AFE_DL0_CUR_MSB 0x3e48 -+#define AFE_DL0_CUR 0x3e4c -+#define AFE_DL0_END_MSB 0x3e50 -+#define AFE_DL0_END 0x3e54 -+#define AFE_DL0_RCH_MON 0x3e58 -+#define AFE_DL0_LCH_MON 0x3e5c -+#define AFE_DL0_CON0 0x3e60 -+#define AFE_VUL0_BASE_MSB 0x4220 -+#define AFE_VUL0_BASE 0x4224 -+#define AFE_VUL0_CUR_MSB 0x4228 -+#define AFE_VUL0_CUR 0x422c -+#define AFE_VUL0_END_MSB 0x4230 -+#define AFE_VUL0_END 0x4234 -+#define AFE_VUL0_CON0 0x4238 -+ -+#define AFE_MAX_REGISTER AFE_VUL0_CON0 -+#define AFE_IRQ_STATUS_BITS 0x7 -+#define AFE_IRQ_CNT_SHIFT 0 -+#define AFE_IRQ_CNT_MASK 0xffffff -+ -+/* AUDIO_TOP_CON2 */ -+#define CLK_OUT5_PDN BIT(14) -+#define CLK_OUT5_PDN_MASK BIT(14) -+#define CLK_IN5_PDN BIT(7) -+#define CLK_IN5_PDN_MASK BIT(7) -+ -+/* AUDIO_TOP_CON4 */ -+#define PDN_APLL_TUNER2 BIT(12) -+#define PDN_APLL_TUNER2_MASK BIT(12) -+ -+/* AUDIO_ENGEN_CON0 */ -+#define AUD_APLL2_EN BIT(3) -+#define AUD_APLL2_EN_MASK BIT(3) -+#define AUD_26M_EN BIT(0) -+#define AUD_26M_EN_MASK BIT(0) -+ -+/* AFE_DL0_CON0 */ -+#define DL0_ON_SFT 28 -+#define DL0_ON_MASK 0x1 -+#define DL0_ON_MASK_SFT BIT(28) -+#define DL0_MINLEN_SFT 20 -+#define DL0_MINLEN_MASK 0xf -+#define DL0_MINLEN_MASK_SFT (0xf << 20) -+#define DL0_MODE_SFT 8 -+#define DL0_MODE_MASK 0x1f -+#define DL0_MODE_MASK_SFT (0x1f << 8) -+#define DL0_PBUF_SIZE_SFT 5 -+#define DL0_PBUF_SIZE_MASK 0x3 -+#define DL0_PBUF_SIZE_MASK_SFT (0x3 << 5) -+#define DL0_MONO_SFT 4 -+#define DL0_MONO_MASK 0x1 -+#define DL0_MONO_MASK_SFT BIT(4) -+#define DL0_HALIGN_SFT 2 -+#define DL0_HALIGN_MASK 0x1 -+#define DL0_HALIGN_MASK_SFT BIT(2) -+#define DL0_HD_MODE_SFT 0 -+#define DL0_HD_MODE_MASK 0x3 -+#define DL0_HD_MODE_MASK_SFT (0x3 << 0) -+ -+/* AFE_VUL0_CON0 */ -+#define VUL0_ON_SFT 28 -+#define VUL0_ON_MASK 0x1 -+#define VUL0_ON_MASK_SFT BIT(28) -+#define VUL0_MODE_SFT 8 -+#define VUL0_MODE_MASK 0x1f -+#define VUL0_MODE_MASK_SFT (0x1f << 8) -+#define VUL0_MONO_SFT 4 -+#define VUL0_MONO_MASK 0x1 -+#define VUL0_MONO_MASK_SFT BIT(4) -+#define VUL0_HALIGN_SFT 2 -+#define VUL0_HALIGN_MASK 0x1 -+#define VUL0_HALIGN_MASK_SFT BIT(2) -+#define VUL0_HD_MODE_SFT 0 -+#define VUL0_HD_MODE_MASK 0x3 -+#define VUL0_HD_MODE_MASK_SFT (0x3 << 0) -+ -+/* AFE_IRQ_MCU_CON */ -+#define IRQ_MCU_MODE_SFT 4 -+#define IRQ_MCU_MODE_MASK 0x1f -+#define IRQ_MCU_MODE_MASK_SFT (0x1f << 4) -+#define IRQ_MCU_ON_SFT 0 -+#define IRQ_MCU_ON_MASK 0x1 -+#define IRQ_MCU_ON_MASK_SFT BIT(0) -+#define IRQ0_MCU_CLR_SFT 0 -+#define IRQ0_MCU_CLR_MASK 0x1 -+#define IRQ0_MCU_CLR_MASK_SFT BIT(0) -+#define IRQ1_MCU_CLR_SFT 1 -+#define IRQ1_MCU_CLR_MASK 0x1 -+#define IRQ1_MCU_CLR_MASK_SFT BIT(1) -+#define IRQ2_MCU_CLR_SFT 2 -+#define IRQ2_MCU_CLR_MASK 0x1 -+#define IRQ2_MCU_CLR_MASK_SFT BIT(2) -+ -+/* ETDM_IN5_CON2 */ -+#define IN_CLK_SRC(x) ((x) << 10) -+#define IN_CLK_SRC_SFT 10 -+#define IN_CLK_SRC_MASK GENMASK(12, 10) -+ -+/* ETDM_IN5_CON3 */ -+#define IN_SEL_FS(x) ((x) << 26) -+#define IN_SEL_FS_SFT 26 -+#define IN_SEL_FS_MASK GENMASK(30, 26) -+ -+/* ETDM_IN5_CON4 */ -+#define IN_RELATCH(x) ((x) << 20) -+#define IN_RELATCH_SFT 20 -+#define IN_RELATCH_MASK GENMASK(24, 20) -+#define IN_CLK_INV BIT(18) -+#define IN_CLK_INV_MASK BIT(18) -+ -+/* ETDM_IN5_CON0 & ETDM_OUT5_CON0 */ -+#define RELATCH_SRC_MASK GENMASK(30, 28) -+#define ETDM_CH_NUM_MASK GENMASK(27, 23) -+#define ETDM_WRD_LEN_MASK GENMASK(20, 16) -+#define ETDM_BIT_LEN_MASK GENMASK(15, 11) -+#define ETDM_FMT_MASK GENMASK(8, 6) -+#define ETDM_SYNC BIT(1) -+#define ETDM_SYNC_MASK BIT(1) -+#define ETDM_EN BIT(0) -+#define ETDM_EN_MASK BIT(0) -+ -+/* ETDM_OUT5_CON4 */ -+#define OUT_RELATCH(x) ((x) << 24) -+#define OUT_RELATCH_SFT 24 -+#define OUT_RELATCH_MASK GENMASK(28, 24) -+#define OUT_CLK_SRC(x) ((x) << 6) -+#define OUT_CLK_SRC_SFT 6 -+#define OUT_CLK_SRC_MASK GENMASK(8, 6) -+#define OUT_SEL_FS(x) (x) -+#define OUT_SEL_FS_SFT 0 -+#define OUT_SEL_FS_MASK GENMASK(4, 0) -+ -+/* ETDM_OUT5_CON5 */ -+#define ETDM_CLK_DIV BIT(12) -+#define ETDM_CLK_DIV_MASK BIT(12) -+#define OUT_CLK_INV BIT(9) -+#define OUT_CLK_INV_MASK BIT(9) -+ -+/* ETDM_4_7_COWORK_CON0 */ -+#define OUT_SEL(x) ((x) << 12) -+#define OUT_SEL_SFT 12 -+#define OUT_SEL_MASK GENMASK(15, 12) -+#endif diff --git a/target/linux/mediatek/patches-5.15/860-v6.6-02-ASoC-mediatek-mt7986-support-etdm-in-platform-driver.patch b/target/linux/mediatek/patches-5.15/860-v6.6-02-ASoC-mediatek-mt7986-support-etdm-in-platform-driver.patch deleted file mode 100644 index f22add580f..0000000000 --- a/target/linux/mediatek/patches-5.15/860-v6.6-02-ASoC-mediatek-mt7986-support-etdm-in-platform-driver.patch +++ /dev/null @@ -1,430 +0,0 @@ -From 948a288897015fb3ee63b3f720b396b590c17fd7 Mon Sep 17 00:00:00 2001 -From: Maso Huang -Date: Thu, 17 Aug 2023 18:13:34 +0800 -Subject: [PATCH 2/9] ASoC: mediatek: mt7986: support etdm in platform driver - -Add mt7986 etdm dai driver support. - -Signed-off-by: Maso Huang -Reviewed-by: AngeloGioacchino Del Regno -Link: https://lore.kernel.org/r/20230817101338.18782-3-maso.huang@mediatek.com -Signed-off-by: Mark Brown ---- - sound/soc/mediatek/mt7986/mt7986-dai-etdm.c | 411 ++++++++++++++++++++ - 1 file changed, 411 insertions(+) - create mode 100644 sound/soc/mediatek/mt7986/mt7986-dai-etdm.c - ---- /dev/null -+++ b/sound/soc/mediatek/mt7986/mt7986-dai-etdm.c -@@ -0,0 +1,411 @@ -+// SPDX-License-Identifier: GPL-2.0 -+/* -+ * MediaTek ALSA SoC Audio DAI eTDM Control -+ * -+ * Copyright (c) 2023 MediaTek Inc. -+ * Authors: Vic Wu -+ * Maso Huang -+ */ -+ -+#include -+#include -+#include -+#include -+#include "mt7986-afe-common.h" -+#include "mt7986-reg.h" -+ -+#define HOPPING_CLK 0 -+#define APLL_CLK 1 -+#define MTK_DAI_ETDM_FORMAT_I2S 0 -+#define MTK_DAI_ETDM_FORMAT_DSPA 4 -+#define MTK_DAI_ETDM_FORMAT_DSPB 5 -+ -+enum { -+ MTK_ETDM_RATE_8K = 0, -+ MTK_ETDM_RATE_12K = 1, -+ MTK_ETDM_RATE_16K = 2, -+ MTK_ETDM_RATE_24K = 3, -+ MTK_ETDM_RATE_32K = 4, -+ MTK_ETDM_RATE_48K = 5, -+ MTK_ETDM_RATE_96K = 7, -+ MTK_ETDM_RATE_192K = 9, -+ MTK_ETDM_RATE_11K = 16, -+ MTK_ETDM_RATE_22K = 17, -+ MTK_ETDM_RATE_44K = 18, -+ MTK_ETDM_RATE_88K = 19, -+ MTK_ETDM_RATE_176K = 20, -+}; -+ -+struct mtk_dai_etdm_priv { -+ bool bck_inv; -+ bool lrck_inv; -+ bool slave_mode; -+ unsigned int format; -+}; -+ -+static unsigned int mt7986_etdm_rate_transform(struct device *dev, unsigned int rate) -+{ -+ switch (rate) { -+ case 8000: -+ return MTK_ETDM_RATE_8K; -+ case 11025: -+ return MTK_ETDM_RATE_11K; -+ case 12000: -+ return MTK_ETDM_RATE_12K; -+ case 16000: -+ return MTK_ETDM_RATE_16K; -+ case 22050: -+ return MTK_ETDM_RATE_22K; -+ case 24000: -+ return MTK_ETDM_RATE_24K; -+ case 32000: -+ return MTK_ETDM_RATE_32K; -+ case 44100: -+ return MTK_ETDM_RATE_44K; -+ case 48000: -+ return MTK_ETDM_RATE_48K; -+ case 88200: -+ return MTK_ETDM_RATE_88K; -+ case 96000: -+ return MTK_ETDM_RATE_96K; -+ case 176400: -+ return MTK_ETDM_RATE_176K; -+ case 192000: -+ return MTK_ETDM_RATE_192K; -+ default: -+ dev_warn(dev, "%s(), rate %u invalid, using %d!!!\n", -+ __func__, rate, MTK_ETDM_RATE_48K); -+ return MTK_ETDM_RATE_48K; -+ } -+} -+ -+static int get_etdm_wlen(unsigned int bitwidth) -+{ -+ return bitwidth <= 16 ? 16 : 32; -+} -+ -+/* dai component */ -+/* interconnection */ -+ -+static const struct snd_kcontrol_new o124_mix[] = { -+ SOC_DAPM_SINGLE_AUTODISABLE("I032_Switch", AFE_CONN124_1, 0, 1, 0), -+}; -+ -+static const struct snd_kcontrol_new o125_mix[] = { -+ SOC_DAPM_SINGLE_AUTODISABLE("I033_Switch", AFE_CONN125_1, 1, 1, 0), -+}; -+ -+static const struct snd_soc_dapm_widget mtk_dai_etdm_widgets[] = { -+ -+ /* DL */ -+ SND_SOC_DAPM_MIXER("I150", SND_SOC_NOPM, 0, 0, NULL, 0), -+ SND_SOC_DAPM_MIXER("I151", SND_SOC_NOPM, 0, 0, NULL, 0), -+ /* UL */ -+ SND_SOC_DAPM_MIXER("O124", SND_SOC_NOPM, 0, 0, o124_mix, ARRAY_SIZE(o124_mix)), -+ SND_SOC_DAPM_MIXER("O125", SND_SOC_NOPM, 0, 0, o125_mix, ARRAY_SIZE(o125_mix)), -+}; -+ -+static const struct snd_soc_dapm_route mtk_dai_etdm_routes[] = { -+ {"I150", NULL, "ETDM Capture"}, -+ {"I151", NULL, "ETDM Capture"}, -+ {"ETDM Playback", NULL, "O124"}, -+ {"ETDM Playback", NULL, "O125"}, -+ {"O124", "I032_Switch", "I032"}, -+ {"O125", "I033_Switch", "I033"}, -+}; -+ -+/* dai ops */ -+static int mtk_dai_etdm_startup(struct snd_pcm_substream *substream, -+ struct snd_soc_dai *dai) -+{ -+ struct mtk_base_afe *afe = snd_soc_dai_get_drvdata(dai); -+ struct mt7986_afe_private *afe_priv = afe->platform_priv; -+ int ret; -+ -+ ret = clk_bulk_prepare_enable(afe_priv->num_clks, afe_priv->clks); -+ if (ret) -+ return dev_err_probe(afe->dev, ret, "Failed to enable clocks\n"); -+ -+ regmap_update_bits(afe->regmap, AUDIO_TOP_CON2, CLK_OUT5_PDN_MASK, 0); -+ regmap_update_bits(afe->regmap, AUDIO_TOP_CON2, CLK_IN5_PDN_MASK, 0); -+ -+ return 0; -+} -+ -+static void mtk_dai_etdm_shutdown(struct snd_pcm_substream *substream, -+ struct snd_soc_dai *dai) -+{ -+ struct mtk_base_afe *afe = snd_soc_dai_get_drvdata(dai); -+ struct mt7986_afe_private *afe_priv = afe->platform_priv; -+ -+ regmap_update_bits(afe->regmap, AUDIO_TOP_CON2, CLK_OUT5_PDN_MASK, -+ CLK_OUT5_PDN); -+ regmap_update_bits(afe->regmap, AUDIO_TOP_CON2, CLK_IN5_PDN_MASK, -+ CLK_IN5_PDN); -+ -+ clk_bulk_disable_unprepare(afe_priv->num_clks, afe_priv->clks); -+} -+ -+static unsigned int get_etdm_ch_fixup(unsigned int channels) -+{ -+ if (channels > 16) -+ return 24; -+ else if (channels > 8) -+ return 16; -+ else if (channels > 4) -+ return 8; -+ else if (channels > 2) -+ return 4; -+ else -+ return 2; -+} -+ -+static int mtk_dai_etdm_config(struct mtk_base_afe *afe, -+ struct snd_pcm_hw_params *params, -+ struct snd_soc_dai *dai, -+ int stream) -+{ -+ struct mt7986_afe_private *afe_priv = afe->platform_priv; -+ struct mtk_dai_etdm_priv *etdm_data = afe_priv->dai_priv[dai->id]; -+ unsigned int rate = params_rate(params); -+ unsigned int etdm_rate = mt7986_etdm_rate_transform(afe->dev, rate); -+ unsigned int afe_rate = mt7986_afe_rate_transform(afe->dev, rate); -+ unsigned int channels = params_channels(params); -+ unsigned int bit_width = params_width(params); -+ unsigned int wlen = get_etdm_wlen(bit_width); -+ unsigned int val = 0; -+ unsigned int mask = 0; -+ -+ dev_dbg(afe->dev, "%s(), stream %d, rate %u, bitwidth %u\n", -+ __func__, stream, rate, bit_width); -+ -+ /* CON0 */ -+ mask |= ETDM_BIT_LEN_MASK; -+ val |= FIELD_PREP(ETDM_BIT_LEN_MASK, bit_width - 1); -+ mask |= ETDM_WRD_LEN_MASK; -+ val |= FIELD_PREP(ETDM_WRD_LEN_MASK, wlen - 1); -+ mask |= ETDM_FMT_MASK; -+ val |= FIELD_PREP(ETDM_FMT_MASK, etdm_data->format); -+ mask |= ETDM_CH_NUM_MASK; -+ val |= FIELD_PREP(ETDM_CH_NUM_MASK, get_etdm_ch_fixup(channels) - 1); -+ mask |= RELATCH_SRC_MASK; -+ val |= FIELD_PREP(RELATCH_SRC_MASK, APLL_CLK); -+ -+ switch (stream) { -+ case SNDRV_PCM_STREAM_PLAYBACK: -+ /* set ETDM_OUT5_CON0 */ -+ regmap_update_bits(afe->regmap, ETDM_OUT5_CON0, mask, val); -+ -+ /* set ETDM_OUT5_CON4 */ -+ regmap_update_bits(afe->regmap, ETDM_OUT5_CON4, -+ OUT_RELATCH_MASK, OUT_RELATCH(afe_rate)); -+ regmap_update_bits(afe->regmap, ETDM_OUT5_CON4, -+ OUT_CLK_SRC_MASK, OUT_CLK_SRC(APLL_CLK)); -+ regmap_update_bits(afe->regmap, ETDM_OUT5_CON4, -+ OUT_SEL_FS_MASK, OUT_SEL_FS(etdm_rate)); -+ -+ /* set ETDM_OUT5_CON5 */ -+ regmap_update_bits(afe->regmap, ETDM_OUT5_CON5, -+ ETDM_CLK_DIV_MASK, ETDM_CLK_DIV); -+ break; -+ case SNDRV_PCM_STREAM_CAPTURE: -+ /* set ETDM_IN5_CON0 */ -+ regmap_update_bits(afe->regmap, ETDM_IN5_CON0, mask, val); -+ regmap_update_bits(afe->regmap, ETDM_IN5_CON0, -+ ETDM_SYNC_MASK, ETDM_SYNC); -+ -+ /* set ETDM_IN5_CON2 */ -+ regmap_update_bits(afe->regmap, ETDM_IN5_CON2, -+ IN_CLK_SRC_MASK, IN_CLK_SRC(APLL_CLK)); -+ -+ /* set ETDM_IN5_CON3 */ -+ regmap_update_bits(afe->regmap, ETDM_IN5_CON3, -+ IN_SEL_FS_MASK, IN_SEL_FS(etdm_rate)); -+ -+ /* set ETDM_IN5_CON4 */ -+ regmap_update_bits(afe->regmap, ETDM_IN5_CON4, -+ IN_RELATCH_MASK, IN_RELATCH(afe_rate)); -+ break; -+ default: -+ break; -+ } -+ -+ return 0; -+} -+ -+static int mtk_dai_etdm_hw_params(struct snd_pcm_substream *substream, -+ struct snd_pcm_hw_params *params, -+ struct snd_soc_dai *dai) -+{ -+ struct mtk_base_afe *afe = snd_soc_dai_get_drvdata(dai); -+ -+ mtk_dai_etdm_config(afe, params, dai, SNDRV_PCM_STREAM_PLAYBACK); -+ mtk_dai_etdm_config(afe, params, dai, SNDRV_PCM_STREAM_CAPTURE); -+ -+ return 0; -+} -+ -+static int mtk_dai_etdm_trigger(struct snd_pcm_substream *substream, int cmd, -+ struct snd_soc_dai *dai) -+{ -+ struct mtk_base_afe *afe = snd_soc_dai_get_drvdata(dai); -+ -+ dev_dbg(afe->dev, "%s(), cmd %d, dai id %d\n", __func__, cmd, dai->id); -+ switch (cmd) { -+ case SNDRV_PCM_TRIGGER_START: -+ case SNDRV_PCM_TRIGGER_RESUME: -+ regmap_update_bits(afe->regmap, ETDM_IN5_CON0, ETDM_EN_MASK, -+ ETDM_EN); -+ regmap_update_bits(afe->regmap, ETDM_OUT5_CON0, ETDM_EN_MASK, -+ ETDM_EN); -+ break; -+ case SNDRV_PCM_TRIGGER_STOP: -+ case SNDRV_PCM_TRIGGER_SUSPEND: -+ regmap_update_bits(afe->regmap, ETDM_IN5_CON0, ETDM_EN_MASK, -+ 0); -+ regmap_update_bits(afe->regmap, ETDM_OUT5_CON0, ETDM_EN_MASK, -+ 0); -+ break; -+ default: -+ break; -+ } -+ -+ return 0; -+} -+ -+static int mtk_dai_etdm_set_fmt(struct snd_soc_dai *dai, unsigned int fmt) -+{ -+ struct mtk_base_afe *afe = snd_soc_dai_get_drvdata(dai); -+ struct mt7986_afe_private *afe_priv = afe->platform_priv; -+ struct mtk_dai_etdm_priv *etdm_data; -+ void *priv_data; -+ -+ switch (dai->id) { -+ case MT7986_DAI_ETDM: -+ break; -+ default: -+ dev_warn(afe->dev, "%s(), id %d not support\n", -+ __func__, dai->id); -+ return -EINVAL; -+ } -+ -+ priv_data = devm_kzalloc(afe->dev, sizeof(struct mtk_dai_etdm_priv), -+ GFP_KERNEL); -+ if (!priv_data) -+ return -ENOMEM; -+ -+ afe_priv->dai_priv[dai->id] = priv_data; -+ etdm_data = afe_priv->dai_priv[dai->id]; -+ -+ switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { -+ case SND_SOC_DAIFMT_I2S: -+ etdm_data->format = MTK_DAI_ETDM_FORMAT_I2S; -+ break; -+ case SND_SOC_DAIFMT_DSP_A: -+ etdm_data->format = MTK_DAI_ETDM_FORMAT_DSPA; -+ break; -+ case SND_SOC_DAIFMT_DSP_B: -+ etdm_data->format = MTK_DAI_ETDM_FORMAT_DSPB; -+ break; -+ default: -+ return -EINVAL; -+ } -+ -+ switch (fmt & SND_SOC_DAIFMT_INV_MASK) { -+ case SND_SOC_DAIFMT_NB_NF: -+ etdm_data->bck_inv = false; -+ etdm_data->lrck_inv = false; -+ break; -+ case SND_SOC_DAIFMT_NB_IF: -+ etdm_data->bck_inv = false; -+ etdm_data->lrck_inv = true; -+ break; -+ case SND_SOC_DAIFMT_IB_NF: -+ etdm_data->bck_inv = true; -+ etdm_data->lrck_inv = false; -+ break; -+ case SND_SOC_DAIFMT_IB_IF: -+ etdm_data->bck_inv = true; -+ etdm_data->lrck_inv = true; -+ break; -+ default: -+ return -EINVAL; -+ } -+ -+ switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { -+ case SND_SOC_DAIFMT_CBM_CFM: -+ etdm_data->slave_mode = true; -+ break; -+ case SND_SOC_DAIFMT_CBS_CFS: -+ etdm_data->slave_mode = false; -+ break; -+ default: -+ return -EINVAL; -+ } -+ -+ return 0; -+} -+ -+static const struct snd_soc_dai_ops mtk_dai_etdm_ops = { -+ .startup = mtk_dai_etdm_startup, -+ .shutdown = mtk_dai_etdm_shutdown, -+ .hw_params = mtk_dai_etdm_hw_params, -+ .trigger = mtk_dai_etdm_trigger, -+ .set_fmt = mtk_dai_etdm_set_fmt, -+}; -+ -+/* dai driver */ -+#define MTK_ETDM_RATES (SNDRV_PCM_RATE_8000_48000 |\ -+ SNDRV_PCM_RATE_88200 |\ -+ SNDRV_PCM_RATE_96000 |\ -+ SNDRV_PCM_RATE_176400 |\ -+ SNDRV_PCM_RATE_192000) -+ -+#define MTK_ETDM_FORMATS (SNDRV_PCM_FMTBIT_S16_LE |\ -+ SNDRV_PCM_FMTBIT_S24_LE |\ -+ SNDRV_PCM_FMTBIT_S32_LE) -+ -+static struct snd_soc_dai_driver mtk_dai_etdm_driver[] = { -+ { -+ .name = "ETDM", -+ .id = MT7986_DAI_ETDM, -+ .capture = { -+ .stream_name = "ETDM Capture", -+ .channels_min = 1, -+ .channels_max = 2, -+ .rates = MTK_ETDM_RATES, -+ .formats = MTK_ETDM_FORMATS, -+ }, -+ .playback = { -+ .stream_name = "ETDM Playback", -+ .channels_min = 1, -+ .channels_max = 2, -+ .rates = MTK_ETDM_RATES, -+ .formats = MTK_ETDM_FORMATS, -+ }, -+ .ops = &mtk_dai_etdm_ops, -+ .symmetric_rate = 1, -+ .symmetric_sample_bits = 1, -+ }, -+}; -+ -+int mt7986_dai_etdm_register(struct mtk_base_afe *afe) -+{ -+ struct mtk_base_afe_dai *dai; -+ -+ dai = devm_kzalloc(afe->dev, sizeof(*dai), GFP_KERNEL); -+ if (!dai) -+ return -ENOMEM; -+ -+ list_add(&dai->list, &afe->sub_dais); -+ -+ dai->dai_drivers = mtk_dai_etdm_driver; -+ dai->num_dai_drivers = ARRAY_SIZE(mtk_dai_etdm_driver); -+ -+ dai->dapm_widgets = mtk_dai_etdm_widgets; -+ dai->num_dapm_widgets = ARRAY_SIZE(mtk_dai_etdm_widgets); -+ dai->dapm_routes = mtk_dai_etdm_routes; -+ dai->num_dapm_routes = ARRAY_SIZE(mtk_dai_etdm_routes); -+ -+ return 0; -+} diff --git a/target/linux/mediatek/patches-5.15/860-v6.6-03-ASoC-mediatek-mt7986-add-platform-driver.patch b/target/linux/mediatek/patches-5.15/860-v6.6-03-ASoC-mediatek-mt7986-add-platform-driver.patch deleted file mode 100644 index 8139fdc668..0000000000 --- a/target/linux/mediatek/patches-5.15/860-v6.6-03-ASoC-mediatek-mt7986-add-platform-driver.patch +++ /dev/null @@ -1,685 +0,0 @@ -From fc7776dee86bc07d22820a904760a95f49a2f12e Mon Sep 17 00:00:00 2001 -From: Maso Huang -Date: Thu, 17 Aug 2023 18:13:35 +0800 -Subject: [PATCH 3/9] ASoC: mediatek: mt7986: add platform driver - -Add mt7986 platform driver. - -Signed-off-by: Maso Huang -Reviewed-by: AngeloGioacchino Del Regno -Link: https://lore.kernel.org/r/20230817101338.18782-4-maso.huang@mediatek.com -Signed-off-by: Mark Brown ---- - sound/soc/mediatek/Kconfig | 10 + - sound/soc/mediatek/Makefile | 1 + - sound/soc/mediatek/mt7986/Makefile | 8 + - sound/soc/mediatek/mt7986/mt7986-afe-pcm.c | 622 +++++++++++++++++++++ - 4 files changed, 641 insertions(+) - create mode 100644 sound/soc/mediatek/mt7986/Makefile - create mode 100644 sound/soc/mediatek/mt7986/mt7986-afe-pcm.c - ---- a/sound/soc/mediatek/Kconfig -+++ b/sound/soc/mediatek/Kconfig -@@ -54,6 +54,16 @@ config SND_SOC_MT6797_MT6351 - Select Y if you have such device. - If unsure select "N". - -+config SND_SOC_MT7986 -+ tristate "ASoC support for Mediatek MT7986 chip" -+ depends on ARCH_MEDIATEK -+ select SND_SOC_MEDIATEK -+ help -+ This adds ASoC platform driver support for MediaTek MT7986 chip -+ that can be used with other codecs. -+ Select Y if you have such device. -+ If unsure select "N". -+ - config SND_SOC_MT8173 - tristate "ASoC support for Mediatek MT8173 chip" - depends on ARCH_MEDIATEK ---- a/sound/soc/mediatek/Makefile -+++ b/sound/soc/mediatek/Makefile -@@ -2,6 +2,7 @@ - obj-$(CONFIG_SND_SOC_MEDIATEK) += common/ - obj-$(CONFIG_SND_SOC_MT2701) += mt2701/ - obj-$(CONFIG_SND_SOC_MT6797) += mt6797/ -+obj-$(CONFIG_SND_SOC_MT7986) += mt7986/ - obj-$(CONFIG_SND_SOC_MT8173) += mt8173/ - obj-$(CONFIG_SND_SOC_MT8183) += mt8183/ - obj-$(CONFIG_SND_SOC_MT8192) += mt8192/ ---- /dev/null -+++ b/sound/soc/mediatek/mt7986/Makefile -@@ -0,0 +1,8 @@ -+# SPDX-License-Identifier: GPL-2.0 -+ -+# platform driver -+snd-soc-mt7986-afe-objs := \ -+ mt7986-afe-pcm.o \ -+ mt7986-dai-etdm.o -+ -+obj-$(CONFIG_SND_SOC_MT7986) += snd-soc-mt7986-afe.o ---- /dev/null -+++ b/sound/soc/mediatek/mt7986/mt7986-afe-pcm.c -@@ -0,0 +1,622 @@ -+// SPDX-License-Identifier: GPL-2.0 -+/* -+ * MediaTek ALSA SoC AFE platform driver for MT7986 -+ * -+ * Copyright (c) 2023 MediaTek Inc. -+ * Authors: Vic Wu -+ * Maso Huang -+ */ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#include "mt7986-afe-common.h" -+#include "mt7986-reg.h" -+#include "../common/mtk-afe-platform-driver.h" -+#include "../common/mtk-afe-fe-dai.h" -+ -+enum { -+ MTK_AFE_RATE_8K = 0, -+ MTK_AFE_RATE_11K = 1, -+ MTK_AFE_RATE_12K = 2, -+ MTK_AFE_RATE_16K = 4, -+ MTK_AFE_RATE_22K = 5, -+ MTK_AFE_RATE_24K = 6, -+ MTK_AFE_RATE_32K = 8, -+ MTK_AFE_RATE_44K = 9, -+ MTK_AFE_RATE_48K = 10, -+ MTK_AFE_RATE_88K = 13, -+ MTK_AFE_RATE_96K = 14, -+ MTK_AFE_RATE_176K = 17, -+ MTK_AFE_RATE_192K = 18, -+}; -+ -+enum { -+ CLK_INFRA_AUD_BUS_CK = 0, -+ CLK_INFRA_AUD_26M_CK, -+ CLK_INFRA_AUD_L_CK, -+ CLK_INFRA_AUD_AUD_CK, -+ CLK_INFRA_AUD_EG2_CK, -+ CLK_NUM -+}; -+ -+static const char *aud_clks[CLK_NUM] = { -+ [CLK_INFRA_AUD_BUS_CK] = "aud_bus_ck", -+ [CLK_INFRA_AUD_26M_CK] = "aud_26m_ck", -+ [CLK_INFRA_AUD_L_CK] = "aud_l_ck", -+ [CLK_INFRA_AUD_AUD_CK] = "aud_aud_ck", -+ [CLK_INFRA_AUD_EG2_CK] = "aud_eg2_ck", -+}; -+ -+unsigned int mt7986_afe_rate_transform(struct device *dev, unsigned int rate) -+{ -+ switch (rate) { -+ case 8000: -+ return MTK_AFE_RATE_8K; -+ case 11025: -+ return MTK_AFE_RATE_11K; -+ case 12000: -+ return MTK_AFE_RATE_12K; -+ case 16000: -+ return MTK_AFE_RATE_16K; -+ case 22050: -+ return MTK_AFE_RATE_22K; -+ case 24000: -+ return MTK_AFE_RATE_24K; -+ case 32000: -+ return MTK_AFE_RATE_32K; -+ case 44100: -+ return MTK_AFE_RATE_44K; -+ case 48000: -+ return MTK_AFE_RATE_48K; -+ case 88200: -+ return MTK_AFE_RATE_88K; -+ case 96000: -+ return MTK_AFE_RATE_96K; -+ case 176400: -+ return MTK_AFE_RATE_176K; -+ case 192000: -+ return MTK_AFE_RATE_192K; -+ default: -+ dev_warn(dev, "%s(), rate %u invalid, using %d!!!\n", -+ __func__, rate, MTK_AFE_RATE_48K); -+ return MTK_AFE_RATE_48K; -+ } -+} -+ -+static const struct snd_pcm_hardware mt7986_afe_hardware = { -+ .info = SNDRV_PCM_INFO_MMAP | -+ SNDRV_PCM_INFO_INTERLEAVED | -+ SNDRV_PCM_INFO_MMAP_VALID, -+ .formats = SNDRV_PCM_FMTBIT_S16_LE | -+ SNDRV_PCM_FMTBIT_S24_LE | -+ SNDRV_PCM_FMTBIT_S32_LE, -+ .period_bytes_min = 256, -+ .period_bytes_max = 4 * 48 * 1024, -+ .periods_min = 2, -+ .periods_max = 256, -+ .buffer_bytes_max = 8 * 48 * 1024, -+ .fifo_size = 0, -+}; -+ -+static int mt7986_memif_fs(struct snd_pcm_substream *substream, -+ unsigned int rate) -+{ -+ struct snd_soc_pcm_runtime *rtd = substream->private_data; -+ struct snd_soc_component *component = snd_soc_rtdcom_lookup(rtd, AFE_PCM_NAME); -+ struct mtk_base_afe *afe = snd_soc_component_get_drvdata(component); -+ -+ return mt7986_afe_rate_transform(afe->dev, rate); -+} -+ -+static int mt7986_irq_fs(struct snd_pcm_substream *substream, -+ unsigned int rate) -+{ -+ struct snd_soc_pcm_runtime *rtd = substream->private_data; -+ struct snd_soc_component *component = snd_soc_rtdcom_lookup(rtd, AFE_PCM_NAME); -+ struct mtk_base_afe *afe = snd_soc_component_get_drvdata(component); -+ -+ return mt7986_afe_rate_transform(afe->dev, rate); -+} -+ -+#define MTK_PCM_RATES (SNDRV_PCM_RATE_8000_48000 |\ -+ SNDRV_PCM_RATE_88200 |\ -+ SNDRV_PCM_RATE_96000 |\ -+ SNDRV_PCM_RATE_176400 |\ -+ SNDRV_PCM_RATE_192000) -+ -+#define MTK_PCM_FORMATS (SNDRV_PCM_FMTBIT_S16_LE |\ -+ SNDRV_PCM_FMTBIT_S24_LE |\ -+ SNDRV_PCM_FMTBIT_S32_LE) -+ -+static struct snd_soc_dai_driver mt7986_memif_dai_driver[] = { -+ /* FE DAIs: memory intefaces to CPU */ -+ { -+ .name = "DL1", -+ .id = MT7986_MEMIF_DL1, -+ .playback = { -+ .stream_name = "DL1", -+ .channels_min = 1, -+ .channels_max = 2, -+ .rates = MTK_PCM_RATES, -+ .formats = MTK_PCM_FORMATS, -+ }, -+ .ops = &mtk_afe_fe_ops, -+ }, -+ { -+ .name = "UL1", -+ .id = MT7986_MEMIF_VUL12, -+ .capture = { -+ .stream_name = "UL1", -+ .channels_min = 1, -+ .channels_max = 2, -+ .rates = MTK_PCM_RATES, -+ .formats = MTK_PCM_FORMATS, -+ }, -+ .ops = &mtk_afe_fe_ops, -+ }, -+}; -+ -+static const struct snd_kcontrol_new o018_mix[] = { -+ SOC_DAPM_SINGLE_AUTODISABLE("I150_Switch", AFE_CONN018_4, 22, 1, 0), -+}; -+ -+static const struct snd_kcontrol_new o019_mix[] = { -+ SOC_DAPM_SINGLE_AUTODISABLE("I151_Switch", AFE_CONN019_4, 23, 1, 0), -+}; -+ -+static const struct snd_soc_dapm_widget mt7986_memif_widgets[] = { -+ /* DL */ -+ SND_SOC_DAPM_MIXER("I032", SND_SOC_NOPM, 0, 0, NULL, 0), -+ SND_SOC_DAPM_MIXER("I033", SND_SOC_NOPM, 0, 0, NULL, 0), -+ -+ /* UL */ -+ SND_SOC_DAPM_MIXER("O018", SND_SOC_NOPM, 0, 0, -+ o018_mix, ARRAY_SIZE(o018_mix)), -+ SND_SOC_DAPM_MIXER("O019", SND_SOC_NOPM, 0, 0, -+ o019_mix, ARRAY_SIZE(o019_mix)), -+}; -+ -+static const struct snd_soc_dapm_route mt7986_memif_routes[] = { -+ {"I032", NULL, "DL1"}, -+ {"I033", NULL, "DL1"}, -+ {"UL1", NULL, "O018"}, -+ {"UL1", NULL, "O019"}, -+ {"O018", "I150_Switch", "I150"}, -+ {"O019", "I151_Switch", "I151"}, -+}; -+ -+static const struct snd_soc_component_driver mt7986_afe_pcm_dai_component = { -+ .name = "mt7986-afe-pcm-dai", -+}; -+ -+static const struct mtk_base_memif_data memif_data[MT7986_MEMIF_NUM] = { -+ [MT7986_MEMIF_DL1] = { -+ .name = "DL1", -+ .id = MT7986_MEMIF_DL1, -+ .reg_ofs_base = AFE_DL0_BASE, -+ .reg_ofs_cur = AFE_DL0_CUR, -+ .reg_ofs_end = AFE_DL0_END, -+ .reg_ofs_base_msb = AFE_DL0_BASE_MSB, -+ .reg_ofs_cur_msb = AFE_DL0_CUR_MSB, -+ .reg_ofs_end_msb = AFE_DL0_END_MSB, -+ .fs_reg = AFE_DL0_CON0, -+ .fs_shift = DL0_MODE_SFT, -+ .fs_maskbit = DL0_MODE_MASK, -+ .mono_reg = AFE_DL0_CON0, -+ .mono_shift = DL0_MONO_SFT, -+ .enable_reg = AFE_DL0_CON0, -+ .enable_shift = DL0_ON_SFT, -+ .hd_reg = AFE_DL0_CON0, -+ .hd_shift = DL0_HD_MODE_SFT, -+ .hd_align_reg = AFE_DL0_CON0, -+ .hd_align_mshift = DL0_HALIGN_SFT, -+ .pbuf_reg = AFE_DL0_CON0, -+ .pbuf_shift = DL0_PBUF_SIZE_SFT, -+ .minlen_reg = AFE_DL0_CON0, -+ .minlen_shift = DL0_MINLEN_SFT, -+ }, -+ [MT7986_MEMIF_VUL12] = { -+ .name = "VUL12", -+ .id = MT7986_MEMIF_VUL12, -+ .reg_ofs_base = AFE_VUL0_BASE, -+ .reg_ofs_cur = AFE_VUL0_CUR, -+ .reg_ofs_end = AFE_VUL0_END, -+ .reg_ofs_base_msb = AFE_VUL0_BASE_MSB, -+ .reg_ofs_cur_msb = AFE_VUL0_CUR_MSB, -+ .reg_ofs_end_msb = AFE_VUL0_END_MSB, -+ .fs_reg = AFE_VUL0_CON0, -+ .fs_shift = VUL0_MODE_SFT, -+ .fs_maskbit = VUL0_MODE_MASK, -+ .mono_reg = AFE_VUL0_CON0, -+ .mono_shift = VUL0_MONO_SFT, -+ .enable_reg = AFE_VUL0_CON0, -+ .enable_shift = VUL0_ON_SFT, -+ .hd_reg = AFE_VUL0_CON0, -+ .hd_shift = VUL0_HD_MODE_SFT, -+ .hd_align_reg = AFE_VUL0_CON0, -+ .hd_align_mshift = VUL0_HALIGN_SFT, -+ }, -+}; -+ -+static const struct mtk_base_irq_data irq_data[MT7986_IRQ_NUM] = { -+ [MT7986_IRQ_0] = { -+ .id = MT7986_IRQ_0, -+ .irq_cnt_reg = AFE_IRQ0_MCU_CFG1, -+ .irq_cnt_shift = AFE_IRQ_CNT_SHIFT, -+ .irq_cnt_maskbit = AFE_IRQ_CNT_MASK, -+ .irq_fs_reg = AFE_IRQ0_MCU_CFG0, -+ .irq_fs_shift = IRQ_MCU_MODE_SFT, -+ .irq_fs_maskbit = IRQ_MCU_MODE_MASK, -+ .irq_en_reg = AFE_IRQ0_MCU_CFG0, -+ .irq_en_shift = IRQ_MCU_ON_SFT, -+ .irq_clr_reg = AFE_IRQ_MCU_CLR, -+ .irq_clr_shift = IRQ0_MCU_CLR_SFT, -+ }, -+ [MT7986_IRQ_1] = { -+ .id = MT7986_IRQ_1, -+ .irq_cnt_reg = AFE_IRQ1_MCU_CFG1, -+ .irq_cnt_shift = AFE_IRQ_CNT_SHIFT, -+ .irq_cnt_maskbit = AFE_IRQ_CNT_MASK, -+ .irq_fs_reg = AFE_IRQ1_MCU_CFG0, -+ .irq_fs_shift = IRQ_MCU_MODE_SFT, -+ .irq_fs_maskbit = IRQ_MCU_MODE_MASK, -+ .irq_en_reg = AFE_IRQ1_MCU_CFG0, -+ .irq_en_shift = IRQ_MCU_ON_SFT, -+ .irq_clr_reg = AFE_IRQ_MCU_CLR, -+ .irq_clr_shift = IRQ1_MCU_CLR_SFT, -+ }, -+ [MT7986_IRQ_2] = { -+ .id = MT7986_IRQ_2, -+ .irq_cnt_reg = AFE_IRQ2_MCU_CFG1, -+ .irq_cnt_shift = AFE_IRQ_CNT_SHIFT, -+ .irq_cnt_maskbit = AFE_IRQ_CNT_MASK, -+ .irq_fs_reg = AFE_IRQ2_MCU_CFG0, -+ .irq_fs_shift = IRQ_MCU_MODE_SFT, -+ .irq_fs_maskbit = IRQ_MCU_MODE_MASK, -+ .irq_en_reg = AFE_IRQ2_MCU_CFG0, -+ .irq_en_shift = IRQ_MCU_ON_SFT, -+ .irq_clr_reg = AFE_IRQ_MCU_CLR, -+ .irq_clr_shift = IRQ2_MCU_CLR_SFT, -+ }, -+}; -+ -+static bool mt7986_is_volatile_reg(struct device *dev, unsigned int reg) -+{ -+ /* -+ * Those auto-gen regs are read-only, so put it as volatile because -+ * volatile registers cannot be cached, which means that they cannot -+ * be set when power is off -+ */ -+ -+ switch (reg) { -+ case AFE_DL0_CUR_MSB: -+ case AFE_DL0_CUR: -+ case AFE_DL0_RCH_MON: -+ case AFE_DL0_LCH_MON: -+ case AFE_VUL0_CUR_MSB: -+ case AFE_VUL0_CUR: -+ case AFE_IRQ_MCU_STATUS: -+ case AFE_MEMIF_RD_MON: -+ case AFE_MEMIF_WR_MON: -+ return true; -+ default: -+ return false; -+ }; -+} -+ -+static const struct regmap_config mt7986_afe_regmap_config = { -+ .reg_bits = 32, -+ .reg_stride = 4, -+ .val_bits = 32, -+ .volatile_reg = mt7986_is_volatile_reg, -+ .max_register = AFE_MAX_REGISTER, -+ .num_reg_defaults_raw = ((AFE_MAX_REGISTER / 4) + 1), -+}; -+ -+static int mt7986_init_clock(struct mtk_base_afe *afe) -+{ -+ struct mt7986_afe_private *afe_priv = afe->platform_priv; -+ int ret, i; -+ -+ afe_priv->clks = devm_kcalloc(afe->dev, CLK_NUM, -+ sizeof(*afe_priv->clks), GFP_KERNEL); -+ if (!afe_priv->clks) -+ return -ENOMEM; -+ afe_priv->num_clks = CLK_NUM; -+ -+ for (i = 0; i < afe_priv->num_clks; i++) -+ afe_priv->clks[i].id = aud_clks[i]; -+ -+ ret = devm_clk_bulk_get(afe->dev, afe_priv->num_clks, afe_priv->clks); -+ if (ret) -+ return dev_err_probe(afe->dev, ret, "Failed to get clocks\n"); -+ -+ return 0; -+} -+ -+static irqreturn_t mt7986_afe_irq_handler(int irq_id, void *dev) -+{ -+ struct mtk_base_afe *afe = dev; -+ struct mtk_base_afe_irq *irq; -+ u32 mcu_en, status, status_mcu; -+ int i, ret; -+ irqreturn_t irq_ret = IRQ_HANDLED; -+ -+ /* get irq that is sent to MCU */ -+ regmap_read(afe->regmap, AFE_IRQ_MCU_EN, &mcu_en); -+ -+ ret = regmap_read(afe->regmap, AFE_IRQ_MCU_STATUS, &status); -+ /* only care IRQ which is sent to MCU */ -+ status_mcu = status & mcu_en & AFE_IRQ_STATUS_BITS; -+ -+ if (ret || status_mcu == 0) { -+ dev_err(afe->dev, "%s(), irq status err, ret %d, status 0x%x, mcu_en 0x%x\n", -+ __func__, ret, status, mcu_en); -+ -+ irq_ret = IRQ_NONE; -+ goto err_irq; -+ } -+ -+ for (i = 0; i < MT7986_MEMIF_NUM; i++) { -+ struct mtk_base_afe_memif *memif = &afe->memif[i]; -+ -+ if (!memif->substream) -+ continue; -+ -+ if (memif->irq_usage < 0) -+ continue; -+ -+ irq = &afe->irqs[memif->irq_usage]; -+ -+ if (status_mcu & (1 << irq->irq_data->irq_en_shift)) -+ snd_pcm_period_elapsed(memif->substream); -+ } -+ -+err_irq: -+ /* clear irq */ -+ regmap_write(afe->regmap, AFE_IRQ_MCU_CLR, status_mcu); -+ -+ return irq_ret; -+} -+ -+static int mt7986_afe_runtime_suspend(struct device *dev) -+{ -+ struct mtk_base_afe *afe = dev_get_drvdata(dev); -+ struct mt7986_afe_private *afe_priv = afe->platform_priv; -+ -+ if (!afe->regmap || afe_priv->pm_runtime_bypass_reg_ctl) -+ goto skip_regmap; -+ -+ /* disable clk*/ -+ regmap_update_bits(afe->regmap, AUDIO_TOP_CON4, 0x3fff, 0x3fff); -+ regmap_update_bits(afe->regmap, AUDIO_ENGEN_CON0, AUD_APLL2_EN_MASK, 0); -+ regmap_update_bits(afe->regmap, AUDIO_ENGEN_CON0, AUD_26M_EN_MASK, 0); -+ -+ /* make sure all irq status are cleared, twice intended */ -+ regmap_update_bits(afe->regmap, AFE_IRQ_MCU_CLR, 0xffff, 0xffff); -+ -+skip_regmap: -+ clk_bulk_disable_unprepare(afe_priv->num_clks, afe_priv->clks); -+ -+ return 0; -+} -+ -+static int mt7986_afe_runtime_resume(struct device *dev) -+{ -+ struct mtk_base_afe *afe = dev_get_drvdata(dev); -+ struct mt7986_afe_private *afe_priv = afe->platform_priv; -+ int ret; -+ -+ ret = clk_bulk_prepare_enable(afe_priv->num_clks, afe_priv->clks); -+ if (ret) -+ return dev_err_probe(afe->dev, ret, "Failed to enable clocks\n"); -+ -+ if (!afe->regmap || afe_priv->pm_runtime_bypass_reg_ctl) -+ return 0; -+ -+ /* enable clk*/ -+ regmap_update_bits(afe->regmap, AUDIO_TOP_CON4, 0x3fff, 0); -+ regmap_update_bits(afe->regmap, AUDIO_ENGEN_CON0, AUD_APLL2_EN_MASK, -+ AUD_APLL2_EN); -+ regmap_update_bits(afe->regmap, AUDIO_ENGEN_CON0, AUD_26M_EN_MASK, -+ AUD_26M_EN); -+ -+ return 0; -+} -+ -+static int mt7986_afe_component_probe(struct snd_soc_component *component) -+{ -+ return mtk_afe_add_sub_dai_control(component); -+} -+ -+static const struct snd_soc_component_driver mt7986_afe_component = { -+ .name = AFE_PCM_NAME, -+ .probe = mt7986_afe_component_probe, -+ .pointer = mtk_afe_pcm_pointer, -+ .pcm_construct = mtk_afe_pcm_new, -+}; -+ -+static int mt7986_dai_memif_register(struct mtk_base_afe *afe) -+{ -+ struct mtk_base_afe_dai *dai; -+ -+ dai = devm_kzalloc(afe->dev, sizeof(*dai), GFP_KERNEL); -+ if (!dai) -+ return -ENOMEM; -+ -+ list_add(&dai->list, &afe->sub_dais); -+ -+ dai->dai_drivers = mt7986_memif_dai_driver; -+ dai->num_dai_drivers = ARRAY_SIZE(mt7986_memif_dai_driver); -+ -+ dai->dapm_widgets = mt7986_memif_widgets; -+ dai->num_dapm_widgets = ARRAY_SIZE(mt7986_memif_widgets); -+ dai->dapm_routes = mt7986_memif_routes; -+ dai->num_dapm_routes = ARRAY_SIZE(mt7986_memif_routes); -+ -+ return 0; -+} -+ -+typedef int (*dai_register_cb)(struct mtk_base_afe *); -+static const dai_register_cb dai_register_cbs[] = { -+ mt7986_dai_etdm_register, -+ mt7986_dai_memif_register, -+}; -+ -+static int mt7986_afe_pcm_dev_probe(struct platform_device *pdev) -+{ -+ struct mtk_base_afe *afe; -+ struct mt7986_afe_private *afe_priv; -+ struct device *dev; -+ int i, irq_id, ret; -+ -+ afe = devm_kzalloc(&pdev->dev, sizeof(*afe), GFP_KERNEL); -+ if (!afe) -+ return -ENOMEM; -+ platform_set_drvdata(pdev, afe); -+ -+ afe->platform_priv = devm_kzalloc(&pdev->dev, sizeof(*afe_priv), -+ GFP_KERNEL); -+ if (!afe->platform_priv) -+ return -ENOMEM; -+ -+ afe_priv = afe->platform_priv; -+ afe->dev = &pdev->dev; -+ dev = afe->dev; -+ -+ afe->base_addr = devm_platform_ioremap_resource(pdev, 0); -+ if (IS_ERR(afe->base_addr)) -+ return PTR_ERR(afe->base_addr); -+ -+ /* initial audio related clock */ -+ ret = mt7986_init_clock(afe); -+ if (ret) -+ return dev_err_probe(dev, ret, "Cannot initialize clocks\n"); -+ -+ ret = devm_pm_runtime_enable(dev); -+ if (ret) -+ return ret; -+ -+ /* enable clock for regcache get default value from hw */ -+ afe_priv->pm_runtime_bypass_reg_ctl = true; -+ pm_runtime_get_sync(&pdev->dev); -+ -+ afe->regmap = devm_regmap_init_mmio(&pdev->dev, afe->base_addr, -+ &mt7986_afe_regmap_config); -+ -+ pm_runtime_put_sync(&pdev->dev); -+ if (IS_ERR(afe->regmap)) -+ return PTR_ERR(afe->regmap); -+ -+ afe_priv->pm_runtime_bypass_reg_ctl = false; -+ -+ /* init memif */ -+ afe->memif_size = MT7986_MEMIF_NUM; -+ afe->memif = devm_kcalloc(dev, afe->memif_size, sizeof(*afe->memif), -+ GFP_KERNEL); -+ if (!afe->memif) -+ return -ENOMEM; -+ -+ for (i = 0; i < afe->memif_size; i++) { -+ afe->memif[i].data = &memif_data[i]; -+ afe->memif[i].irq_usage = -1; -+ } -+ -+ mutex_init(&afe->irq_alloc_lock); -+ -+ /* irq initialize */ -+ afe->irqs_size = MT7986_IRQ_NUM; -+ afe->irqs = devm_kcalloc(dev, afe->irqs_size, sizeof(*afe->irqs), -+ GFP_KERNEL); -+ if (!afe->irqs) -+ return -ENOMEM; -+ -+ for (i = 0; i < afe->irqs_size; i++) -+ afe->irqs[i].irq_data = &irq_data[i]; -+ -+ /* request irq */ -+ irq_id = platform_get_irq(pdev, 0); -+ if (irq_id < 0) { -+ ret = irq_id; -+ return dev_err_probe(dev, ret, "No irq found\n"); -+ } -+ ret = devm_request_irq(dev, irq_id, mt7986_afe_irq_handler, -+ IRQF_TRIGGER_NONE, "asys-isr", (void *)afe); -+ if (ret) -+ return dev_err_probe(dev, ret, "Failed to request irq for asys-isr\n"); -+ -+ /* init sub_dais */ -+ INIT_LIST_HEAD(&afe->sub_dais); -+ -+ for (i = 0; i < ARRAY_SIZE(dai_register_cbs); i++) { -+ ret = dai_register_cbs[i](afe); -+ if (ret) -+ return dev_err_probe(dev, ret, "DAI register failed, i: %d\n", i); -+ } -+ -+ /* init dai_driver and component_driver */ -+ ret = mtk_afe_combine_sub_dai(afe); -+ if (ret) -+ return dev_err_probe(dev, ret, "mtk_afe_combine_sub_dai fail\n"); -+ -+ afe->mtk_afe_hardware = &mt7986_afe_hardware; -+ afe->memif_fs = mt7986_memif_fs; -+ afe->irq_fs = mt7986_irq_fs; -+ -+ afe->runtime_resume = mt7986_afe_runtime_resume; -+ afe->runtime_suspend = mt7986_afe_runtime_suspend; -+ -+ /* register component */ -+ ret = devm_snd_soc_register_component(&pdev->dev, -+ &mt7986_afe_component, -+ NULL, 0); -+ if (ret) -+ return dev_err_probe(dev, ret, "Cannot register AFE component\n"); -+ -+ ret = devm_snd_soc_register_component(afe->dev, -+ &mt7986_afe_pcm_dai_component, -+ afe->dai_drivers, -+ afe->num_dai_drivers); -+ if (ret) -+ return dev_err_probe(dev, ret, "Cannot register PCM DAI component\n"); -+ -+ return 0; -+} -+ -+static void mt7986_afe_pcm_dev_remove(struct platform_device *pdev) -+{ -+ pm_runtime_disable(&pdev->dev); -+ if (!pm_runtime_status_suspended(&pdev->dev)) -+ mt7986_afe_runtime_suspend(&pdev->dev); -+} -+ -+static const struct of_device_id mt7986_afe_pcm_dt_match[] = { -+ { .compatible = "mediatek,mt7986-afe" }, -+ { /* sentinel */ } -+}; -+MODULE_DEVICE_TABLE(of, mt7986_afe_pcm_dt_match); -+ -+static const struct dev_pm_ops mt7986_afe_pm_ops = { -+ SET_RUNTIME_PM_OPS(mt7986_afe_runtime_suspend, -+ mt7986_afe_runtime_resume, NULL) -+}; -+ -+static struct platform_driver mt7986_afe_pcm_driver = { -+ .driver = { -+ .name = "mt7986-audio", -+ .of_match_table = mt7986_afe_pcm_dt_match, -+ .pm = &mt7986_afe_pm_ops, -+ }, -+ .probe = mt7986_afe_pcm_dev_probe, -+ .remove_new = mt7986_afe_pcm_dev_remove, -+}; -+module_platform_driver(mt7986_afe_pcm_driver); -+ -+MODULE_DESCRIPTION("MediaTek SoC AFE platform driver for ALSA MT7986"); -+MODULE_AUTHOR("Vic Wu "); -+MODULE_LICENSE("GPL"); diff --git a/target/linux/mediatek/patches-5.15/860-v6.6-04-ASoC-mediatek-mt7986-add-machine-driver-with-wm8960.patch b/target/linux/mediatek/patches-5.15/860-v6.6-04-ASoC-mediatek-mt7986-add-machine-driver-with-wm8960.patch deleted file mode 100644 index dd354c04e3..0000000000 --- a/target/linux/mediatek/patches-5.15/860-v6.6-04-ASoC-mediatek-mt7986-add-machine-driver-with-wm8960.patch +++ /dev/null @@ -1,243 +0,0 @@ -From ddf6abc1c78072f8ccad59166be95f0ca5af8ca4 Mon Sep 17 00:00:00 2001 -From: Maso Huang -Date: Thu, 17 Aug 2023 18:13:36 +0800 -Subject: [PATCH 4/9] ASoC: mediatek: mt7986: add machine driver with wm8960 - -Add support for mt7986 board with wm8960. - -Signed-off-by: Maso Huang -Reviewed-by: AngeloGioacchino Del Regno -Link: https://lore.kernel.org/r/20230817101338.18782-5-maso.huang@mediatek.com -Signed-off-by: Mark Brown ---- - sound/soc/mediatek/Kconfig | 10 ++ - sound/soc/mediatek/mt7986/Makefile | 1 + - sound/soc/mediatek/mt7986/mt7986-wm8960.c | 196 ++++++++++++++++++++++ - 3 files changed, 207 insertions(+) - create mode 100644 sound/soc/mediatek/mt7986/mt7986-wm8960.c - ---- a/sound/soc/mediatek/Kconfig -+++ b/sound/soc/mediatek/Kconfig -@@ -64,6 +64,16 @@ config SND_SOC_MT7986 - Select Y if you have such device. - If unsure select "N". - -+config SND_SOC_MT7986_WM8960 -+ tristate "ASoc Audio driver for MT7986 with WM8960 codec" -+ depends on SND_SOC_MT7986 && I2C -+ select SND_SOC_WM8960 -+ help -+ This adds support for ASoC machine driver for MediaTek MT7986 -+ boards with the WM8960 codecs. -+ Select Y if you have such device. -+ If unsure select "N". -+ - config SND_SOC_MT8173 - tristate "ASoC support for Mediatek MT8173 chip" - depends on ARCH_MEDIATEK ---- a/sound/soc/mediatek/mt7986/Makefile -+++ b/sound/soc/mediatek/mt7986/Makefile -@@ -6,3 +6,4 @@ snd-soc-mt7986-afe-objs := \ - mt7986-dai-etdm.o - - obj-$(CONFIG_SND_SOC_MT7986) += snd-soc-mt7986-afe.o -+obj-$(CONFIG_SND_SOC_MT7986_WM8960) += mt7986-wm8960.o ---- /dev/null -+++ b/sound/soc/mediatek/mt7986/mt7986-wm8960.c -@@ -0,0 +1,196 @@ -+// SPDX-License-Identifier: GPL-2.0 -+/* -+ * mt7986-wm8960.c -- MT7986-WM8960 ALSA SoC machine driver -+ * -+ * Copyright (c) 2023 MediaTek Inc. -+ * Authors: Vic Wu -+ * Maso Huang -+ */ -+ -+#include -+#include -+ -+#include "mt7986-afe-common.h" -+ -+struct mt7986_wm8960_priv { -+ struct device_node *platform_node; -+ struct device_node *codec_node; -+}; -+ -+static const struct snd_soc_dapm_widget mt7986_wm8960_widgets[] = { -+ SND_SOC_DAPM_HP("Headphone", NULL), -+ SND_SOC_DAPM_MIC("AMIC", NULL), -+}; -+ -+static const struct snd_kcontrol_new mt7986_wm8960_controls[] = { -+ SOC_DAPM_PIN_SWITCH("Headphone"), -+ SOC_DAPM_PIN_SWITCH("AMIC"), -+}; -+ -+SND_SOC_DAILINK_DEFS(playback, -+ DAILINK_COMP_ARRAY(COMP_CPU("DL1")), -+ DAILINK_COMP_ARRAY(COMP_DUMMY()), -+ DAILINK_COMP_ARRAY(COMP_EMPTY())); -+ -+SND_SOC_DAILINK_DEFS(capture, -+ DAILINK_COMP_ARRAY(COMP_CPU("UL1")), -+ DAILINK_COMP_ARRAY(COMP_DUMMY()), -+ DAILINK_COMP_ARRAY(COMP_EMPTY())); -+ -+SND_SOC_DAILINK_DEFS(codec, -+ DAILINK_COMP_ARRAY(COMP_CPU("ETDM")), -+ DAILINK_COMP_ARRAY(COMP_CODEC(NULL, "wm8960-hifi")), -+ DAILINK_COMP_ARRAY(COMP_EMPTY())); -+ -+static struct snd_soc_dai_link mt7986_wm8960_dai_links[] = { -+ /* FE */ -+ { -+ .name = "wm8960-playback", -+ .stream_name = "wm8960-playback", -+ .trigger = {SND_SOC_DPCM_TRIGGER_POST, -+ SND_SOC_DPCM_TRIGGER_POST}, -+ .dynamic = 1, -+ .dpcm_playback = 1, -+ SND_SOC_DAILINK_REG(playback), -+ }, -+ { -+ .name = "wm8960-capture", -+ .stream_name = "wm8960-capture", -+ .trigger = {SND_SOC_DPCM_TRIGGER_POST, -+ SND_SOC_DPCM_TRIGGER_POST}, -+ .dynamic = 1, -+ .dpcm_capture = 1, -+ SND_SOC_DAILINK_REG(capture), -+ }, -+ /* BE */ -+ { -+ .name = "wm8960-codec", -+ .no_pcm = 1, -+ .dai_fmt = SND_SOC_DAIFMT_I2S | -+ SND_SOC_DAIFMT_NB_NF | -+ SND_SOC_DAIFMT_CBS_CFS | -+ SND_SOC_DAIFMT_GATED, -+ .dpcm_playback = 1, -+ .dpcm_capture = 1, -+ SND_SOC_DAILINK_REG(codec), -+ }, -+}; -+ -+static struct snd_soc_card mt7986_wm8960_card = { -+ .name = "mt7986-wm8960", -+ .owner = THIS_MODULE, -+ .dai_link = mt7986_wm8960_dai_links, -+ .num_links = ARRAY_SIZE(mt7986_wm8960_dai_links), -+ .controls = mt7986_wm8960_controls, -+ .num_controls = ARRAY_SIZE(mt7986_wm8960_controls), -+ .dapm_widgets = mt7986_wm8960_widgets, -+ .num_dapm_widgets = ARRAY_SIZE(mt7986_wm8960_widgets), -+}; -+ -+static int mt7986_wm8960_machine_probe(struct platform_device *pdev) -+{ -+ struct snd_soc_card *card = &mt7986_wm8960_card; -+ struct snd_soc_dai_link *dai_link; -+ struct device_node *platform, *codec; -+ struct mt7986_wm8960_priv *priv; -+ int ret, i; -+ -+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); -+ if (!priv) -+ return -ENOMEM; -+ -+ platform = of_get_child_by_name(pdev->dev.of_node, "platform"); -+ -+ if (platform) { -+ priv->platform_node = of_parse_phandle(platform, "sound-dai", 0); -+ of_node_put(platform); -+ -+ if (!priv->platform_node) { -+ dev_err(&pdev->dev, "Failed to parse platform/sound-dai property\n"); -+ return -EINVAL; -+ } -+ } else { -+ dev_err(&pdev->dev, "Property 'platform' missing or invalid\n"); -+ return -EINVAL; -+ } -+ -+ for_each_card_prelinks(card, i, dai_link) { -+ if (dai_link->platforms->name) -+ continue; -+ dai_link->platforms->of_node = priv->platform_node; -+ } -+ -+ card->dev = &pdev->dev; -+ -+ codec = of_get_child_by_name(pdev->dev.of_node, "codec"); -+ -+ if (codec) { -+ priv->codec_node = of_parse_phandle(codec, "sound-dai", 0); -+ of_node_put(codec); -+ -+ if (!priv->codec_node) { -+ of_node_put(priv->platform_node); -+ dev_err(&pdev->dev, "Failed to parse codec/sound-dai property\n"); -+ return -EINVAL; -+ } -+ } else { -+ of_node_put(priv->platform_node); -+ dev_err(&pdev->dev, "Property 'codec' missing or invalid\n"); -+ return -EINVAL; -+ } -+ -+ for_each_card_prelinks(card, i, dai_link) { -+ if (dai_link->codecs->name) -+ continue; -+ dai_link->codecs->of_node = priv->codec_node; -+ } -+ -+ ret = snd_soc_of_parse_audio_routing(card, "audio-routing"); -+ if (ret) { -+ dev_err(&pdev->dev, "Failed to parse audio-routing: %d\n", ret); -+ goto err_of_node_put; -+ } -+ -+ ret = devm_snd_soc_register_card(&pdev->dev, card); -+ if (ret) { -+ dev_err(&pdev->dev, "%s snd_soc_register_card fail: %d\n", __func__, ret); -+ goto err_of_node_put; -+ } -+ -+err_of_node_put: -+ of_node_put(priv->codec_node); -+ of_node_put(priv->platform_node); -+ return ret; -+} -+ -+static void mt7986_wm8960_machine_remove(struct platform_device *pdev) -+{ -+ struct snd_soc_card *card = platform_get_drvdata(pdev); -+ struct mt7986_wm8960_priv *priv = snd_soc_card_get_drvdata(card); -+ -+ of_node_put(priv->codec_node); -+ of_node_put(priv->platform_node); -+} -+ -+static const struct of_device_id mt7986_wm8960_machine_dt_match[] = { -+ {.compatible = "mediatek,mt7986-wm8960-sound"}, -+ { /* sentinel */ } -+}; -+MODULE_DEVICE_TABLE(of, mt7986_wm8960_machine_dt_match); -+ -+static struct platform_driver mt7986_wm8960_machine = { -+ .driver = { -+ .name = "mt7986-wm8960", -+ .of_match_table = mt7986_wm8960_machine_dt_match, -+ }, -+ .probe = mt7986_wm8960_machine_probe, -+ .remove_new = mt7986_wm8960_machine_remove, -+}; -+ -+module_platform_driver(mt7986_wm8960_machine); -+ -+/* Module information */ -+MODULE_DESCRIPTION("MT7986 WM8960 ALSA SoC machine driver"); -+MODULE_AUTHOR("Vic Wu "); -+MODULE_LICENSE("GPL"); -+MODULE_ALIAS("mt7986 wm8960 soc card"); diff --git a/target/linux/mediatek/patches-5.15/860-v6.6-05-ASoC-dt-bindings-mediatek-mt7986-wm8960-add-mt7986-w.patch b/target/linux/mediatek/patches-5.15/860-v6.6-05-ASoC-dt-bindings-mediatek-mt7986-wm8960-add-mt7986-w.patch deleted file mode 100644 index 8cf0b5464a..0000000000 --- a/target/linux/mediatek/patches-5.15/860-v6.6-05-ASoC-dt-bindings-mediatek-mt7986-wm8960-add-mt7986-w.patch +++ /dev/null @@ -1,87 +0,0 @@ -From 72469f950b629e57e60fbcbefed45e083619b986 Mon Sep 17 00:00:00 2001 -From: Maso Huang -Date: Thu, 17 Aug 2023 18:13:37 +0800 -Subject: [PATCH 5/9] ASoC: dt-bindings: mediatek,mt7986-wm8960: add - mt7986-wm8960 document - -Add document for mt7986 board with wm8960. - -Signed-off-by: Maso Huang -Reviewed-by: AngeloGioacchino Del Regno -Link: https://lore.kernel.org/r/20230817101338.18782-6-maso.huang@mediatek.com -Signed-off-by: Mark Brown ---- - .../sound/mediatek,mt7986-wm8960.yaml | 67 +++++++++++++++++++ - 1 file changed, 67 insertions(+) - create mode 100644 Documentation/devicetree/bindings/sound/mediatek,mt7986-wm8960.yaml - ---- /dev/null -+++ b/Documentation/devicetree/bindings/sound/mediatek,mt7986-wm8960.yaml -@@ -0,0 +1,67 @@ -+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) -+%YAML 1.2 -+--- -+$id: http://devicetree.org/schemas/sound/mediatek,mt7986-wm8960.yaml# -+$schema: http://devicetree.org/meta-schemas/core.yaml# -+ -+title: MediaTek MT7986 sound card with WM8960 codec -+ -+maintainers: -+ - Maso Huang -+ -+allOf: -+ - $ref: sound-card-common.yaml# -+ -+properties: -+ compatible: -+ const: mediatek,mt7986-wm8960-sound -+ -+ platform: -+ type: object -+ additionalProperties: false -+ properties: -+ sound-dai: -+ description: The phandle of MT7986 platform. -+ maxItems: 1 -+ required: -+ - sound-dai -+ -+ codec: -+ type: object -+ additionalProperties: false -+ properties: -+ sound-dai: -+ description: The phandle of wm8960 codec. -+ maxItems: 1 -+ required: -+ - sound-dai -+ -+unevaluatedProperties: false -+ -+required: -+ - compatible -+ - audio-routing -+ - platform -+ - codec -+ -+examples: -+ - | -+ sound { -+ compatible = "mediatek,mt7986-wm8960-sound"; -+ model = "mt7986-wm8960"; -+ audio-routing = -+ "Headphone", "HP_L", -+ "Headphone", "HP_R", -+ "LINPUT1", "AMIC", -+ "RINPUT1", "AMIC"; -+ -+ platform { -+ sound-dai = <&afe>; -+ }; -+ -+ codec { -+ sound-dai = <&wm8960>; -+ }; -+ }; -+ -+... diff --git a/target/linux/mediatek/patches-5.15/860-v6.6-06-ASoC-dt-bindings-mediatek-mt7986-afe-add-audio-afe-d.patch b/target/linux/mediatek/patches-5.15/860-v6.6-06-ASoC-dt-bindings-mediatek-mt7986-afe-add-audio-afe-d.patch deleted file mode 100644 index 236d6a217c..0000000000 --- a/target/linux/mediatek/patches-5.15/860-v6.6-06-ASoC-dt-bindings-mediatek-mt7986-afe-add-audio-afe-d.patch +++ /dev/null @@ -1,180 +0,0 @@ -From d16202eb38585adbc16e32d11188dbc2127015de Mon Sep 17 00:00:00 2001 -From: Maso Huang -Date: Thu, 17 Aug 2023 18:13:38 +0800 -Subject: [PATCH 6/9] ASoC: dt-bindings: mediatek,mt7986-afe: add audio afe - document - -Add mt7986 audio afe document. - -Signed-off-by: Maso Huang -Reviewed-by: AngeloGioacchino Del Regno -Link: https://lore.kernel.org/r/20230817101338.18782-7-maso.huang@mediatek.com -Signed-off-by: Mark Brown ---- - .../bindings/sound/mediatek,mt7986-afe.yaml | 160 ++++++++++++++++++ - 1 file changed, 160 insertions(+) - create mode 100644 Documentation/devicetree/bindings/sound/mediatek,mt7986-afe.yaml - ---- /dev/null -+++ b/Documentation/devicetree/bindings/sound/mediatek,mt7986-afe.yaml -@@ -0,0 +1,160 @@ -+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) -+%YAML 1.2 -+--- -+$id: http://devicetree.org/schemas/sound/mediatek,mt7986-afe.yaml# -+$schema: http://devicetree.org/meta-schemas/core.yaml# -+ -+title: MediaTek AFE PCM controller for MT7986 -+ -+maintainers: -+ - Maso Huang -+ -+properties: -+ compatible: -+ oneOf: -+ - const: mediatek,mt7986-afe -+ - items: -+ - enum: -+ - mediatek,mt7981-afe -+ - mediatek,mt7988-afe -+ - const: mediatek,mt7986-afe -+ -+ reg: -+ maxItems: 1 -+ -+ interrupts: -+ maxItems: 1 -+ -+ clocks: -+ minItems: 5 -+ items: -+ - description: audio bus clock -+ - description: audio 26M clock -+ - description: audio intbus clock -+ - description: audio hopping clock -+ - description: audio pll clock -+ - description: mux for pcm_mck -+ - description: audio i2s/pcm mck -+ -+ clock-names: -+ minItems: 5 -+ items: -+ - const: bus_ck -+ - const: 26m_ck -+ - const: l_ck -+ - const: aud_ck -+ - const: eg2_ck -+ - const: sel -+ - const: i2s_m -+ -+required: -+ - compatible -+ - reg -+ - interrupts -+ - clocks -+ - clock-names -+ -+allOf: -+ - if: -+ properties: -+ compatible: -+ contains: -+ const: mediatek,mt7986-afe -+ then: -+ properties: -+ clocks: -+ items: -+ - description: audio bus clock -+ - description: audio 26M clock -+ - description: audio intbus clock -+ - description: audio hopping clock -+ - description: audio pll clock -+ clock-names: -+ items: -+ - const: bus_ck -+ - const: 26m_ck -+ - const: l_ck -+ - const: aud_ck -+ - const: eg2_ck -+ -+ - if: -+ properties: -+ compatible: -+ contains: -+ const: mediatek,mt7981-afe -+ then: -+ properties: -+ clocks: -+ items: -+ - description: audio bus clock -+ - description: audio 26M clock -+ - description: audio intbus clock -+ - description: audio hopping clock -+ - description: audio pll clock -+ - description: mux for pcm_mck -+ clock-names: -+ items: -+ - const: bus_ck -+ - const: 26m_ck -+ - const: l_ck -+ - const: aud_ck -+ - const: eg2_ck -+ - const: sel -+ -+ - if: -+ properties: -+ compatible: -+ contains: -+ const: mediatek,mt7988-afe -+ then: -+ properties: -+ clocks: -+ items: -+ - description: audio bus clock -+ - description: audio 26M clock -+ - description: audio intbus clock -+ - description: audio hopping clock -+ - description: audio pll clock -+ - description: mux for pcm_mck -+ - description: audio i2s/pcm mck -+ clock-names: -+ items: -+ - const: bus_ck -+ - const: 26m_ck -+ - const: l_ck -+ - const: aud_ck -+ - const: eg2_ck -+ - const: sel -+ - const: i2s_m -+ -+additionalProperties: false -+ -+examples: -+ - | -+ #include -+ #include -+ #include -+ -+ afe@11210000 { -+ compatible = "mediatek,mt7986-afe"; -+ reg = <0x11210000 0x9000>; -+ interrupts = ; -+ clocks = <&infracfg_ao CLK_INFRA_AUD_BUS_CK>, -+ <&infracfg_ao CLK_INFRA_AUD_26M_CK>, -+ <&infracfg_ao CLK_INFRA_AUD_L_CK>, -+ <&infracfg_ao CLK_INFRA_AUD_AUD_CK>, -+ <&infracfg_ao CLK_INFRA_AUD_EG2_CK>; -+ clock-names = "bus_ck", -+ "26m_ck", -+ "l_ck", -+ "aud_ck", -+ "eg2_ck"; -+ assigned-clocks = <&topckgen CLK_TOP_A1SYS_SEL>, -+ <&topckgen CLK_TOP_AUD_L_SEL>, -+ <&topckgen CLK_TOP_A_TUNER_SEL>; -+ assigned-clock-parents = <&topckgen CLK_TOP_APLL2_D4>, -+ <&apmixedsys CLK_APMIXED_APLL2>, -+ <&topckgen CLK_TOP_APLL2_D4>; -+ }; -+ -+... diff --git a/target/linux/mediatek/patches-5.15/860-v6.7-07-ASoC-mediatek-mt7986-drop-the-remove-callback-of-mt7.patch b/target/linux/mediatek/patches-5.15/860-v6.7-07-ASoC-mediatek-mt7986-drop-the-remove-callback-of-mt7.patch deleted file mode 100644 index 413db8233f..0000000000 --- a/target/linux/mediatek/patches-5.15/860-v6.7-07-ASoC-mediatek-mt7986-drop-the-remove-callback-of-mt7.patch +++ /dev/null @@ -1,42 +0,0 @@ -From f3f0934e5c7b9c16e0cb2435be3555382e6293ad Mon Sep 17 00:00:00 2001 -From: Maso Huang -Date: Tue, 24 Oct 2023 11:50:17 +0800 -Subject: [PATCH 7/9] ASoC: mediatek: mt7986: drop the remove callback of - mt7986_wm8960 - -Drop the remove callback of mt7986_wm8960. - -Signed-off-by: Maso Huang -Reviewed-by: AngeloGioacchino Del Regno -Link: https://lore.kernel.org/r/20231024035019.11732-2-maso.huang@mediatek.com -Signed-off-by: Mark Brown ---- - sound/soc/mediatek/mt7986/mt7986-wm8960.c | 10 ---------- - 1 file changed, 10 deletions(-) - ---- a/sound/soc/mediatek/mt7986/mt7986-wm8960.c -+++ b/sound/soc/mediatek/mt7986/mt7986-wm8960.c -@@ -163,15 +163,6 @@ err_of_node_put: - return ret; - } - --static void mt7986_wm8960_machine_remove(struct platform_device *pdev) --{ -- struct snd_soc_card *card = platform_get_drvdata(pdev); -- struct mt7986_wm8960_priv *priv = snd_soc_card_get_drvdata(card); -- -- of_node_put(priv->codec_node); -- of_node_put(priv->platform_node); --} -- - static const struct of_device_id mt7986_wm8960_machine_dt_match[] = { - {.compatible = "mediatek,mt7986-wm8960-sound"}, - { /* sentinel */ } -@@ -184,7 +175,6 @@ static struct platform_driver mt7986_wm8 - .of_match_table = mt7986_wm8960_machine_dt_match, - }, - .probe = mt7986_wm8960_machine_probe, -- .remove_new = mt7986_wm8960_machine_remove, - }; - - module_platform_driver(mt7986_wm8960_machine); diff --git a/target/linux/mediatek/patches-5.15/860-v6.7-08-ASoC-mediatek-mt7986-remove-the-mt7986_wm8960_priv-s.patch b/target/linux/mediatek/patches-5.15/860-v6.7-08-ASoC-mediatek-mt7986-remove-the-mt7986_wm8960_priv-s.patch deleted file mode 100644 index 5c596fc49c..0000000000 --- a/target/linux/mediatek/patches-5.15/860-v6.7-08-ASoC-mediatek-mt7986-remove-the-mt7986_wm8960_priv-s.patch +++ /dev/null @@ -1,105 +0,0 @@ -From 98b8fb2cb4fcab1903d0baf611bf0c3f822a08dc Mon Sep 17 00:00:00 2001 -From: Maso Huang -Date: Tue, 24 Oct 2023 11:50:18 +0800 -Subject: [PATCH 8/9] ASoC: mediatek: mt7986: remove the mt7986_wm8960_priv - structure - -Remove the mt7986_wm8960_priv structure. - -Signed-off-by: Maso Huang -Reviewed-by: AngeloGioacchino Del Regno -Link: https://lore.kernel.org/r/20231024035019.11732-3-maso.huang@mediatek.com -Signed-off-by: Mark Brown ---- - sound/soc/mediatek/mt7986/mt7986-wm8960.c | 33 +++++++++-------------- - 1 file changed, 12 insertions(+), 21 deletions(-) - ---- a/sound/soc/mediatek/mt7986/mt7986-wm8960.c -+++ b/sound/soc/mediatek/mt7986/mt7986-wm8960.c -@@ -12,11 +12,6 @@ - - #include "mt7986-afe-common.h" - --struct mt7986_wm8960_priv { -- struct device_node *platform_node; -- struct device_node *codec_node; --}; -- - static const struct snd_soc_dapm_widget mt7986_wm8960_widgets[] = { - SND_SOC_DAPM_HP("Headphone", NULL), - SND_SOC_DAPM_MIC("AMIC", NULL), -@@ -92,20 +87,18 @@ static int mt7986_wm8960_machine_probe(s - struct snd_soc_card *card = &mt7986_wm8960_card; - struct snd_soc_dai_link *dai_link; - struct device_node *platform, *codec; -- struct mt7986_wm8960_priv *priv; -+ struct device_node *platform_dai_node, *codec_dai_node; - int ret, i; - -- priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); -- if (!priv) -- return -ENOMEM; -+ card->dev = &pdev->dev; - - platform = of_get_child_by_name(pdev->dev.of_node, "platform"); - - if (platform) { -- priv->platform_node = of_parse_phandle(platform, "sound-dai", 0); -+ platform_dai_node = of_parse_phandle(platform, "sound-dai", 0); - of_node_put(platform); - -- if (!priv->platform_node) { -+ if (!platform_dai_node) { - dev_err(&pdev->dev, "Failed to parse platform/sound-dai property\n"); - return -EINVAL; - } -@@ -117,24 +110,22 @@ static int mt7986_wm8960_machine_probe(s - for_each_card_prelinks(card, i, dai_link) { - if (dai_link->platforms->name) - continue; -- dai_link->platforms->of_node = priv->platform_node; -+ dai_link->platforms->of_node = platform_dai_node; - } - -- card->dev = &pdev->dev; -- - codec = of_get_child_by_name(pdev->dev.of_node, "codec"); - - if (codec) { -- priv->codec_node = of_parse_phandle(codec, "sound-dai", 0); -+ codec_dai_node = of_parse_phandle(codec, "sound-dai", 0); - of_node_put(codec); - -- if (!priv->codec_node) { -- of_node_put(priv->platform_node); -+ if (!codec_dai_node) { -+ of_node_put(platform_dai_node); - dev_err(&pdev->dev, "Failed to parse codec/sound-dai property\n"); - return -EINVAL; - } - } else { -- of_node_put(priv->platform_node); -+ of_node_put(platform_dai_node); - dev_err(&pdev->dev, "Property 'codec' missing or invalid\n"); - return -EINVAL; - } -@@ -142,7 +133,7 @@ static int mt7986_wm8960_machine_probe(s - for_each_card_prelinks(card, i, dai_link) { - if (dai_link->codecs->name) - continue; -- dai_link->codecs->of_node = priv->codec_node; -+ dai_link->codecs->of_node = codec_dai_node; - } - - ret = snd_soc_of_parse_audio_routing(card, "audio-routing"); -@@ -158,8 +149,8 @@ static int mt7986_wm8960_machine_probe(s - } - - err_of_node_put: -- of_node_put(priv->codec_node); -- of_node_put(priv->platform_node); -+ of_node_put(platform_dai_node); -+ of_node_put(codec_dai_node); - return ret; - } - diff --git a/target/linux/mediatek/patches-5.15/860-v6.7-09-ASoC-mediatek-mt7986-add-sample-rate-checker.patch b/target/linux/mediatek/patches-5.15/860-v6.7-09-ASoC-mediatek-mt7986-add-sample-rate-checker.patch deleted file mode 100644 index d4128deabc..0000000000 --- a/target/linux/mediatek/patches-5.15/860-v6.7-09-ASoC-mediatek-mt7986-add-sample-rate-checker.patch +++ /dev/null @@ -1,49 +0,0 @@ -From 4e229f4264f4be7a6a554487714c0913ef59cf7f Mon Sep 17 00:00:00 2001 -From: Maso Huang -Date: Tue, 24 Oct 2023 11:50:19 +0800 -Subject: [PATCH 9/9] ASoC: mediatek: mt7986: add sample rate checker - -mt7986 only supports 8/12/16/24/32/48/96/192 kHz - -Signed-off-by: Maso Huang -Reviewed-by: AngeloGioacchino Del Regno -Link: https://lore.kernel.org/r/20231024035019.11732-4-maso.huang@mediatek.com -Signed-off-by: Mark Brown ---- - sound/soc/mediatek/mt7986/mt7986-dai-etdm.c | 23 +++++++++++++++++---- - 1 file changed, 19 insertions(+), 4 deletions(-) - ---- a/sound/soc/mediatek/mt7986/mt7986-dai-etdm.c -+++ b/sound/soc/mediatek/mt7986/mt7986-dai-etdm.c -@@ -237,12 +237,27 @@ static int mtk_dai_etdm_hw_params(struct - struct snd_pcm_hw_params *params, - struct snd_soc_dai *dai) - { -+ unsigned int rate = params_rate(params); - struct mtk_base_afe *afe = snd_soc_dai_get_drvdata(dai); - -- mtk_dai_etdm_config(afe, params, dai, SNDRV_PCM_STREAM_PLAYBACK); -- mtk_dai_etdm_config(afe, params, dai, SNDRV_PCM_STREAM_CAPTURE); -- -- return 0; -+ switch (rate) { -+ case 8000: -+ case 12000: -+ case 16000: -+ case 24000: -+ case 32000: -+ case 48000: -+ case 96000: -+ case 192000: -+ mtk_dai_etdm_config(afe, params, dai, SNDRV_PCM_STREAM_PLAYBACK); -+ mtk_dai_etdm_config(afe, params, dai, SNDRV_PCM_STREAM_CAPTURE); -+ return 0; -+ default: -+ dev_err(afe->dev, -+ "Sample rate %d invalid. Supported rates: 8/12/16/24/32/48/96/192 kHz\n", -+ rate); -+ return -EINVAL; -+ } - } - - static int mtk_dai_etdm_trigger(struct snd_pcm_substream *substream, int cmd, diff --git a/target/linux/mediatek/patches-5.15/861-pending-10-ASoC-mediatek-mt7986-silence-error-in-case-of-EPROBE.patch b/target/linux/mediatek/patches-5.15/861-pending-10-ASoC-mediatek-mt7986-silence-error-in-case-of-EPROBE.patch deleted file mode 100644 index a40c249257..0000000000 --- a/target/linux/mediatek/patches-5.15/861-pending-10-ASoC-mediatek-mt7986-silence-error-in-case-of-EPROBE.patch +++ /dev/null @@ -1,26 +0,0 @@ -From e4cde335d1771863a60b6931e51357b8470e85c4 Mon Sep 17 00:00:00 2001 -From: Daniel Golle -Date: Sun, 10 Dec 2023 22:41:39 +0000 -Subject: [PATCH] ASoC: mediatek: mt7986: silence error in case of - -EPROBE_DEFER - -If probe is defered no error should be printed. Mute it. - -Signed-off-by: Daniel Golle ---- - sound/soc/mediatek/mt7986/mt7986-wm8960.c | 4 +++- - 1 file changed, 3 insertions(+), 1 deletion(-) - ---- a/sound/soc/mediatek/mt7986/mt7986-wm8960.c -+++ b/sound/soc/mediatek/mt7986/mt7986-wm8960.c -@@ -144,7 +144,9 @@ static int mt7986_wm8960_machine_probe(s - - ret = devm_snd_soc_register_card(&pdev->dev, card); - if (ret) { -- dev_err(&pdev->dev, "%s snd_soc_register_card fail: %d\n", __func__, ret); -+ if (ret != -EPROBE_DEFER) -+ dev_err(&pdev->dev, "%s snd_soc_register_card fail: %d\n", __func__, ret); -+ - goto err_of_node_put; - } - diff --git a/target/linux/mediatek/patches-5.15/862-arm64-dts-mt7986-add-afe.patch b/target/linux/mediatek/patches-5.15/862-arm64-dts-mt7986-add-afe.patch deleted file mode 100644 index b31710fe69..0000000000 --- a/target/linux/mediatek/patches-5.15/862-arm64-dts-mt7986-add-afe.patch +++ /dev/null @@ -1,40 +0,0 @@ -From 1c09b694a1e9378931085e77d834a4d9786a5356 Mon Sep 17 00:00:00 2001 -From: Maso Huang -Date: Thu, 7 Sep 2023 10:54:37 +0800 -Subject: [PATCH] arm64: dts: mt7986: add afe - ---- - arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 23 +++++++++++ - 1 files changed, 23 insertions(+) - ---- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi -@@ -248,6 +248,28 @@ - status = "disabled"; - }; - -+ afe: audio-controller@11210000 { -+ compatible = "mediatek,mt7986-afe"; -+ reg = <0 0x11210000 0 0x9000>; -+ interrupts = ; -+ clocks = <&infracfg CLK_INFRA_AUD_BUS_CK>, -+ <&infracfg CLK_INFRA_AUD_26M_CK>, -+ <&infracfg CLK_INFRA_AUD_L_CK>, -+ <&infracfg CLK_INFRA_AUD_AUD_CK>, -+ <&infracfg CLK_INFRA_AUD_EG2_CK>; -+ clock-names = "aud_bus_ck", -+ "aud_26m_ck", -+ "aud_l_ck", -+ "aud_aud_ck", -+ "aud_eg2_ck"; -+ assigned-clocks = <&topckgen CLK_TOP_A1SYS_SEL>, -+ <&topckgen CLK_TOP_AUD_L_SEL>, -+ <&topckgen CLK_TOP_A_TUNER_SEL>; -+ assigned-clock-parents = <&topckgen CLK_TOP_APLL2_D4>, -+ <&apmixedsys CLK_APMIXED_APLL2>, -+ <&topckgen CLK_TOP_APLL2_D4>; -+ }; -+ - pwm: pwm@10048000 { - compatible = "mediatek,mt7986-pwm"; - reg = <0 0x10048000 0 0x1000>; diff --git a/target/linux/mediatek/patches-5.15/863-arm64-dts-mt7986-add-sound-wm8960.patch b/target/linux/mediatek/patches-5.15/863-arm64-dts-mt7986-add-sound-wm8960.patch deleted file mode 100644 index 15e30dec56..0000000000 --- a/target/linux/mediatek/patches-5.15/863-arm64-dts-mt7986-add-sound-wm8960.patch +++ /dev/null @@ -1,61 +0,0 @@ -From 1c09b694a1e9378931085e77d834a4d9786a5356 Mon Sep 17 00:00:00 2001 -From: Maso Huang -Date: Thu, 7 Sep 2023 10:54:37 +0800 -Subject: [PATCH] arm64: dts: mt7986: add sound wm8960 - ---- - .../dts/mediatek/mt7986a-rfb-spim-nand.dts | 39 +++++++++++++++++++ - 1 files changed, 39 insertions(+) - ---- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb-spim-nand.dts -+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb-spim-nand.dts -@@ -4,6 +4,35 @@ - - / { - compatible = "mediatek,mt7986a-rfb-snand"; -+ -+ sound_wm8960 { -+ compatible = "mediatek,mt7986-wm8960-sound"; -+ audio-routing = "Headphone", "HP_L", -+ "Headphone", "HP_R", -+ "LINPUT1", "AMIC", -+ "RINPUT1", "AMIC"; -+ -+ status = "okay"; -+ -+ platform { -+ sound-dai = <&afe>; -+ }; -+ -+ codec { -+ sound-dai = <&wm8960>; -+ }; -+ }; -+}; -+ -+&i2c0 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&i2c_pins>; -+ status = "okay"; -+ -+ wm8960: wm8960@1a { -+ compatible = "wlf,wm8960"; -+ reg = <0x1a>; -+ }; - }; - - &spi0 { -@@ -50,3 +79,13 @@ - &wifi { - mediatek,mtd-eeprom = <&factory 0>; - }; -+ -+&pio { -+ i2c_pins: i2c-pins-3-4 { -+ mux { -+ function = "i2c"; -+ groups = "i2c"; -+ }; -+ }; -+}; -+ diff --git a/target/linux/mediatek/patches-5.15/864-arm64-dts-mt7986-add-sound-overlay-for-bpi-r3.patch b/target/linux/mediatek/patches-5.15/864-arm64-dts-mt7986-add-sound-overlay-for-bpi-r3.patch deleted file mode 100644 index 4fc12bf402..0000000000 --- a/target/linux/mediatek/patches-5.15/864-arm64-dts-mt7986-add-sound-overlay-for-bpi-r3.patch +++ /dev/null @@ -1,65 +0,0 @@ ---- /dev/null -+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-respeaker-2mics.dtso -@@ -0,0 +1,62 @@ -+// SPDX-License-Identifier: (GPL-2.0 OR MIT) -+/* -+ * Copyright (C) 2023 MediaTek Inc. -+ * Author: Maso Huang -+ */ -+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "bananapi,bpi-r3", "mediatek,mt7986a"; -+ -+ fragment@0 { -+ target-path = "/"; -+ __overlay__ { -+ sound_wm8960 { -+ compatible = "mediatek,mt7986-wm8960-sound"; -+ audio-routing = "Headphone", "HP_L", -+ "Headphone", "HP_R", -+ "LINPUT1", "AMIC", -+ "RINPUT1", "AMIC"; -+ -+ status = "okay"; -+ -+ platform { -+ sound-dai = <&afe>; -+ }; -+ -+ codec { -+ sound-dai = <&wm8960>; -+ }; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&i2c0>; -+ __overlay__ { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&i2c_pins>; -+ clock-frequency = <400000>; -+ status = "okay"; -+ -+ wm8960: wm8960@1a { -+ compatible = "wlf,wm8960"; -+ reg = <0x1a>; -+ }; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&pio>; -+ __overlay__ { -+ i2c_pins: i2c-pins-3-4 { -+ mux { -+ function = "i2c"; -+ groups = "i2c"; -+ }; -+ }; -+ }; -+ }; -+}; diff --git a/target/linux/mediatek/patches-5.15/900-dts-mt7622-bpi-r64-aliases-for-dtoverlay.patch b/target/linux/mediatek/patches-5.15/900-dts-mt7622-bpi-r64-aliases-for-dtoverlay.patch deleted file mode 100644 index f779c1e047..0000000000 --- a/target/linux/mediatek/patches-5.15/900-dts-mt7622-bpi-r64-aliases-for-dtoverlay.patch +++ /dev/null @@ -1,65 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -@@ -318,7 +318,7 @@ - /* Attention: GPIO 90 is used to switch between PCIe@1,0 and - * SATA functions. i.e. output-high: PCIe, output-low: SATA - */ -- asm_sel { -+ asmsel: asm_sel { - gpio-hog; - gpios = <90 GPIO_ACTIVE_HIGH>; - output-high; ---- /dev/null -+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64-sata.dtso -@@ -0,0 +1,31 @@ -+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */ -+ -+#include -+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "bananapi,bpi-r64", "mediatek,mt7622"; -+ -+ fragment@0 { -+ target = <&asmsel>; -+ __overlay__ { -+ gpios = <90 GPIO_ACTIVE_LOW>; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&sata>; -+ __overlay__ { -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&sata_phy>; -+ __overlay__ { -+ status = "okay"; -+ }; -+ }; -+}; ---- /dev/null -+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64-pcie1.dtso -@@ -0,0 +1,17 @@ -+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */ -+ -+#include -+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "bananapi,bpi-r64", "mediatek,mt7622"; -+ -+ fragment@0 { -+ target = <&asmsel>; -+ __overlay__ { -+ gpios = <90 GPIO_ACTIVE_HIGH>; -+ }; -+ }; -+}; diff --git a/target/linux/mediatek/patches-5.15/901-arm-add-cmdline-override.patch b/target/linux/mediatek/patches-5.15/901-arm-add-cmdline-override.patch deleted file mode 100644 index 54901f5549..0000000000 --- a/target/linux/mediatek/patches-5.15/901-arm-add-cmdline-override.patch +++ /dev/null @@ -1,54 +0,0 @@ ---- a/arch/arm/Kconfig -+++ b/arch/arm/Kconfig -@@ -1730,6 +1730,14 @@ config ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEN - - endchoice - -+config CMDLINE_OVERRIDE -+ bool "Use alternative cmdline from device tree" -+ help -+ Some bootloaders may have uneditable bootargs. While CMDLINE_FORCE can -+ be used, this is not a good option for kernels that are shared across -+ devices. This setting enables using "chosen/cmdline-override" as the -+ cmdline if it exists in the device tree. -+ - config CMDLINE - string "Default kernel command string" - default "" ---- a/drivers/of/fdt.c -+++ b/drivers/of/fdt.c -@@ -1162,6 +1162,17 @@ int __init early_init_dt_scan_chosen(uns - if (p != NULL && l > 0) - strlcat(data, p, min_t(int, strlen(data) + (int)l, COMMAND_LINE_SIZE)); - -+ /* CONFIG_CMDLINE_OVERRIDE is used to fallback to a different -+ * device tree option of chosen/bootargs-override. This is -+ * helpful on boards where u-boot sets bootargs, and is unable -+ * to be modified. -+ */ -+#ifdef CONFIG_CMDLINE_OVERRIDE -+ p = of_get_flat_dt_prop(node, "bootargs-override", &l); -+ if (p != NULL && l > 0) -+ strlcpy(data, p, min((int)l, COMMAND_LINE_SIZE)); -+#endif -+ - /* - * CONFIG_CMDLINE is meant to be a default in case nothing else - * managed to set the command line, unless CONFIG_CMDLINE_FORCE ---- a/arch/arm64/Kconfig -+++ b/arch/arm64/Kconfig -@@ -2059,6 +2059,14 @@ config CMDLINE_FORCE - - endchoice - -+config CMDLINE_OVERRIDE -+ bool "Use alternative cmdline from device tree" -+ help -+ Some bootloaders may have uneditable bootargs. While CMDLINE_FORCE can -+ be used, this is not a good option for kernels that are shared across -+ devices. This setting enables using "chosen/cmdline-override" as the -+ cmdline if it exists in the device tree. -+ - config EFI_STUB - bool - diff --git a/target/linux/mediatek/patches-5.15/910-dts-mt7622-bpi-r64-wifi-eeprom.patch b/target/linux/mediatek/patches-5.15/910-dts-mt7622-bpi-r64-wifi-eeprom.patch deleted file mode 100644 index 2a863aecf9..0000000000 --- a/target/linux/mediatek/patches-5.15/910-dts-mt7622-bpi-r64-wifi-eeprom.patch +++ /dev/null @@ -1,31 +0,0 @@ ---- a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts -@@ -645,5 +645,28 @@ - }; - - &wmac { -+ mediatek,eeprom-data = <0x22760500 0x0 0x0 0x0 -+ 0x0 0x0 0x0 0x0 -+ 0x0 0x0 0x0 0x0 -+ 0x0 0x44000020 0x0 0x10002000 -+ 0x4400 0x4000000 0x0 0x0 -+ 0x200000b3 0x40b6c3c3 0x26000000 0x41c42600 -+ 0x41c4 0x26000000 0xc0c52600 0x0 -+ 0x0 0x0 0x0 0x0 -+ 0x0 0x0 0x0 0x0 -+ 0x0 0x0 0x0 0x0 -+ 0x0 0x0 0x0 0x0 -+ 0x0 0x0 0x0 0xc6c6 -+ 0xc3c3c2c1 0xc300c3 0x818181 0x83c1c182 -+ 0x83838382 0x0 0x0 0x0 -+ 0x0 0x0 0x0 0x0 -+ 0x84002e00 0x90000087 0x8a000000 0x0 -+ 0x0 0x0 0x0 0x0 -+ 0x0 0x0 0x0 0x0 -+ 0xb000009 0x0 0x0 0x0 -+ 0x0 0x0 0x0 0x0 -+ 0x0 0x0 0x0 0x0 -+ 0x0 0x0 0x0 0x7707>; -+ - status = "okay"; - }; diff --git a/target/linux/mediatek/patches-5.15/920-v5.16-watchdog-mtk-add-disable_wdt_extrst-support.patch b/target/linux/mediatek/patches-5.15/920-v5.16-watchdog-mtk-add-disable_wdt_extrst-support.patch deleted file mode 100644 index d9379721fb..0000000000 --- a/target/linux/mediatek/patches-5.15/920-v5.16-watchdog-mtk-add-disable_wdt_extrst-support.patch +++ /dev/null @@ -1,50 +0,0 @@ -From 59b0f51335644ee603260faaa4298c0115fb7187 Mon Sep 17 00:00:00 2001 -From: Fengquan Chen -Date: Tue, 14 Sep 2021 20:34:54 +0800 -Subject: [PATCH] watchdog: mtk: add disable_wdt_extrst support - -In some cases, we may need watchdog just to trigger an -internal soc reset without sending any output signal. - -Provide a disable_wdt_extrst parameter for configuration. -We can disable or enable it just by configuring dts. - -Signed-off-by: Fengquan Chen -Reviewed-by: Guenter Roeck -Link: https://lore.kernel.org/r/20210914123454.32603-3-Fengquan.Chen@mediatek.com -Signed-off-by: Guenter Roeck -Signed-off-by: Wim Van Sebroeck ---- - drivers/watchdog/mtk_wdt.c | 7 +++++++ - 1 file changed, 7 insertions(+) - ---- a/drivers/watchdog/mtk_wdt.c -+++ b/drivers/watchdog/mtk_wdt.c -@@ -65,6 +65,7 @@ struct mtk_wdt_dev { - void __iomem *wdt_base; - spinlock_t lock; /* protects WDT_SWSYSRST reg */ - struct reset_controller_dev rcdev; -+ bool disable_wdt_extrst; - }; - - struct mtk_wdt_data { -@@ -256,6 +257,8 @@ static int mtk_wdt_start(struct watchdog - reg |= (WDT_MODE_IRQ_EN | WDT_MODE_DUAL_EN); - else - reg &= ~(WDT_MODE_IRQ_EN | WDT_MODE_DUAL_EN); -+ if (mtk_wdt->disable_wdt_extrst) -+ reg &= ~WDT_MODE_EXRST_EN; - reg |= (WDT_MODE_EN | WDT_MODE_KEY); - iowrite32(reg, wdt_base + WDT_MODE); - -@@ -381,6 +384,10 @@ static int mtk_wdt_probe(struct platform - if (err) - return err; - } -+ -+ mtk_wdt->disable_wdt_extrst = -+ of_property_read_bool(dev->of_node, "mediatek,disable-extrst"); -+ - return 0; - } - diff --git a/target/linux/mediatek/patches-5.15/921-v5.19-watchdog-mtk_wdt-mt7986-Add-toprgu-reset-controller.patch b/target/linux/mediatek/patches-5.15/921-v5.19-watchdog-mtk_wdt-mt7986-Add-toprgu-reset-controller.patch deleted file mode 100644 index 96fb215f76..0000000000 --- a/target/linux/mediatek/patches-5.15/921-v5.19-watchdog-mtk_wdt-mt7986-Add-toprgu-reset-controller.patch +++ /dev/null @@ -1,49 +0,0 @@ -From 711a5b25bac95dcd1111521ed71693330e74a926 Mon Sep 17 00:00:00 2001 -From: Sam Shih -Date: Wed, 5 Jan 2022 18:04:56 +0800 -Subject: [PATCH] watchdog: mtk_wdt: mt7986: Add toprgu reset controller - support - -Besides watchdog, the mt7986 toprgu module also provides software reset -functionality for various peripheral subsystems -(eg, ethernet, pcie, and connectivity) - -Signed-off-by: Sam Shih -Reviewed-by: Matthias Brugger -Reviewed-by: Guenter Roeck -Link: https://lore.kernel.org/r/20220105100456.7126-3-sam.shih@mediatek.com -Signed-off-by: Guenter Roeck -Signed-off-by: Wim Van Sebroeck ---- - drivers/watchdog/mtk_wdt.c | 6 ++++++ - 1 file changed, 6 insertions(+) - ---- a/drivers/watchdog/mtk_wdt.c -+++ b/drivers/watchdog/mtk_wdt.c -@@ -10,6 +10,7 @@ - */ - - #include -+#include - #include - #include - #include -@@ -76,6 +77,10 @@ static const struct mtk_wdt_data mt2712_ - .toprgu_sw_rst_num = MT2712_TOPRGU_SW_RST_NUM, - }; - -+static const struct mtk_wdt_data mt7986_data = { -+ .toprgu_sw_rst_num = MT7986_TOPRGU_SW_RST_NUM, -+}; -+ - static const struct mtk_wdt_data mt8183_data = { - .toprgu_sw_rst_num = MT8183_TOPRGU_SW_RST_NUM, - }; -@@ -418,6 +423,7 @@ static int mtk_wdt_resume(struct device - static const struct of_device_id mtk_wdt_dt_ids[] = { - { .compatible = "mediatek,mt2712-wdt", .data = &mt2712_data }, - { .compatible = "mediatek,mt6589-wdt" }, -+ { .compatible = "mediatek,mt7986-wdt", .data = &mt7986_data }, - { .compatible = "mediatek,mt8183-wdt", .data = &mt8183_data }, - { .compatible = "mediatek,mt8192-wdt", .data = &mt8192_data }, - { .compatible = "mediatek,mt8195-wdt", .data = &mt8195_data }, diff --git a/target/linux/mediatek/patches-5.15/922-v6.1-PCI-mediatek-gen3-change-driver-name-to-mtk-pcie-gen.patch b/target/linux/mediatek/patches-5.15/922-v6.1-PCI-mediatek-gen3-change-driver-name-to-mtk-pcie-gen.patch deleted file mode 100644 index f026f5573c..0000000000 --- a/target/linux/mediatek/patches-5.15/922-v6.1-PCI-mediatek-gen3-change-driver-name-to-mtk-pcie-gen.patch +++ /dev/null @@ -1,20 +0,0 @@ -From: Felix Fietkau -Date: Wed, 4 May 2022 12:03:42 +0200 -Subject: [PATCH] PCI: mediatek-gen3: change driver name to mtk-pcie-gen3 - -This allows it to coexist with the other mtk pcie driver in the same kernel - -Signed-off-by: Felix Fietkau ---- - ---- a/drivers/pci/controller/pcie-mediatek-gen3.c -+++ b/drivers/pci/controller/pcie-mediatek-gen3.c -@@ -1031,7 +1031,7 @@ static struct platform_driver mtk_pcie_d - .probe = mtk_pcie_probe, - .remove = mtk_pcie_remove, - .driver = { -- .name = "mtk-pcie", -+ .name = "mtk-pcie-gen3", - .of_match_table = mtk_pcie_of_match, - .pm = &mtk_pcie_pm_ops, - }, diff --git a/target/linux/mediatek/patches-5.15/930-spi-mt65xx-enable-sel-clk.patch b/target/linux/mediatek/patches-5.15/930-spi-mt65xx-enable-sel-clk.patch deleted file mode 100644 index ebb6c060b5..0000000000 --- a/target/linux/mediatek/patches-5.15/930-spi-mt65xx-enable-sel-clk.patch +++ /dev/null @@ -1,29 +0,0 @@ ---- a/drivers/spi/spi-mt65xx.c -+++ b/drivers/spi/spi-mt65xx.c -@@ -1231,10 +1231,16 @@ static int mtk_spi_probe(struct platform - goto err_disable_spi_hclk; - } - -+ ret = clk_prepare_enable(mdata->sel_clk); -+ if (ret < 0) { -+ dev_err(&pdev->dev, "failed to enable sel_clk (%d)\n", ret); -+ goto err_disable_spi_clk; -+ } -+ - ret = clk_set_parent(mdata->sel_clk, mdata->parent_clk); - if (ret < 0) { - dev_err(&pdev->dev, "failed to clk_set_parent (%d)\n", ret); -- goto err_disable_spi_clk; -+ goto err_disable_spi_sel_clk; - } - - mdata->spi_clk_hz = clk_get_rate(mdata->spi_clk); -@@ -1285,6 +1291,8 @@ static int mtk_spi_probe(struct platform - - err_disable_runtime_pm: - pm_runtime_disable(&pdev->dev); -+err_disable_spi_sel_clk: -+ clk_disable_unprepare(mdata->sel_clk); - err_disable_spi_clk: - clk_disable_unprepare(mdata->spi_clk); - err_disable_spi_hclk: diff --git a/target/linux/mediatek/patches-5.15/940-net-ethernet-mtk_wed-rename-mtk_wed_get_memory_regio.patch b/target/linux/mediatek/patches-5.15/940-net-ethernet-mtk_wed-rename-mtk_wed_get_memory_regio.patch deleted file mode 100644 index 30be53518a..0000000000 --- a/target/linux/mediatek/patches-5.15/940-net-ethernet-mtk_wed-rename-mtk_wed_get_memory_regio.patch +++ /dev/null @@ -1,37 +0,0 @@ -From 3cf212c4ce6cd72c09bc47f35f539ba0afd4d106 Mon Sep 17 00:00:00 2001 -Message-Id: <3cf212c4ce6cd72c09bc47f35f539ba0afd4d106.1678716918.git.lorenzo@kernel.org> -From: Lorenzo Bianconi -Date: Sun, 12 Mar 2023 16:40:31 +0100 -Subject: [PATCH net-next 1/2] net: ethernet: mtk_wed: rename - mtk_wed_get_memory_region in mtk_wed_get_reserved_memory_region - -This is a preliminary patch to move wed ilm/dlm and cpuboot properties in -dedicated dts nodes. - -Signed-off-by: Lorenzo Bianconi ---- - drivers/net/ethernet/mediatek/mtk_wed_mcu.c | 8 ++++---- - 1 file changed, 4 insertions(+), 4 deletions(-) - ---- a/drivers/net/ethernet/mediatek/mtk_wed_mcu.c -+++ b/drivers/net/ethernet/mediatek/mtk_wed_mcu.c -@@ -234,8 +234,8 @@ int mtk_wed_mcu_msg_update(struct mtk_we - } - - static int --mtk_wed_get_memory_region(struct mtk_wed_hw *hw, int index, -- struct mtk_wed_wo_memory_region *region) -+mtk_wed_get_reserved_memory_region(struct mtk_wed_hw *hw, int index, -+ struct mtk_wed_wo_memory_region *region) - { - struct reserved_mem *rmem; - struct device_node *np; -@@ -321,7 +321,7 @@ mtk_wed_mcu_load_firmware(struct mtk_wed - if (index < 0) - continue; - -- ret = mtk_wed_get_memory_region(wo->hw, index, &mem_region[i]); -+ ret = mtk_wed_get_reserved_memory_region(wo->hw, index, &mem_region[i]); - if (ret) - return ret; - } diff --git a/target/linux/mediatek/patches-5.15/941-arm64-dts-mt7986-move-cpuboot-in-a-dedicated-node.patch b/target/linux/mediatek/patches-5.15/941-arm64-dts-mt7986-move-cpuboot-in-a-dedicated-node.patch deleted file mode 100644 index 3ba485346c..0000000000 --- a/target/linux/mediatek/patches-5.15/941-arm64-dts-mt7986-move-cpuboot-in-a-dedicated-node.patch +++ /dev/null @@ -1,66 +0,0 @@ -From 247e566e3459481f1fa98733534bfed767e18b42 Mon Sep 17 00:00:00 2001 -Message-Id: <247e566e3459481f1fa98733534bfed767e18b42.1678620342.git.lorenzo@kernel.org> -From: Lorenzo Bianconi -Date: Sat, 11 Mar 2023 16:32:41 +0100 -Subject: [PATCH net-next] arm64: dts: mt7986: move cpuboot in a dedicated node - -Signed-off-by: Lorenzo Bianconi ---- - arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 21 +++++++++++---------- - 1 file changed, 11 insertions(+), 10 deletions(-) - ---- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi -@@ -121,12 +121,6 @@ - reg = <0 0x151f8000 0 0x2000>; - no-map; - }; -- -- wo_boot: wo-boot@15194000 { -- reg = <0 0x15194000 0 0x1000>; -- no-map; -- }; -- - }; - - timer { -@@ -540,10 +534,11 @@ - interrupt-parent = <&gic>; - interrupts = ; - memory-region = <&wo_emi0>, <&wo_ilm0>, <&wo_dlm0>, -- <&wo_data>, <&wo_boot>; -+ <&wo_data>; - memory-region-names = "wo-emi", "wo-ilm", "wo-dlm", -- "wo-data", "wo-boot"; -+ "wo-data"; - mediatek,wo-ccif = <&wo_ccif0>; -+ mediatek,wo-cpuboot = <&wo_cpuboot>; - }; - - wed1: wed@15011000 { -@@ -553,10 +548,11 @@ - interrupt-parent = <&gic>; - interrupts = ; - memory-region = <&wo_emi1>, <&wo_ilm1>, <&wo_dlm1>, -- <&wo_data>, <&wo_boot>; -+ <&wo_data>; - memory-region-names = "wo-emi", "wo-ilm", "wo-dlm", -- "wo-data", "wo-boot"; -+ "wo-data"; - mediatek,wo-ccif = <&wo_ccif1>; -+ mediatek,wo-cpuboot = <&wo_cpuboot>; - }; - - wo_ccif0: syscon@151a5000 { -@@ -573,6 +569,11 @@ - interrupts = ; - }; - -+ wo_cpuboot: syscon@15194000 { -+ compatible = "mediatek,mt7986-wo-cpuboot", "syscon"; -+ reg = <0 0x15194000 0 0x1000>; -+ }; -+ - eth: ethernet@15100000 { - compatible = "mediatek,mt7986-eth"; - reg = <0 0x15100000 0 0x80000>; diff --git a/target/linux/mediatek/patches-5.15/942-net-ethernet-mtk_wed-move-cpuboot-in-a-dedicated-dts.patch b/target/linux/mediatek/patches-5.15/942-net-ethernet-mtk_wed-move-cpuboot-in-a-dedicated-dts.patch deleted file mode 100644 index b4bea2087b..0000000000 --- a/target/linux/mediatek/patches-5.15/942-net-ethernet-mtk_wed-move-cpuboot-in-a-dedicated-dts.patch +++ /dev/null @@ -1,81 +0,0 @@ -From f292d1bf83ec160bef2532b58aa08f5b71041923 Mon Sep 17 00:00:00 2001 -Message-Id: -In-Reply-To: <3cf212c4ce6cd72c09bc47f35f539ba0afd4d106.1678716918.git.lorenzo@kernel.org> -References: <3cf212c4ce6cd72c09bc47f35f539ba0afd4d106.1678716918.git.lorenzo@kernel.org> -From: Lorenzo Bianconi -Date: Sat, 11 Mar 2023 18:13:04 +0100 -Subject: [PATCH net-next 2/2] net: ethernet: mtk_wed: move cpuboot in a - dedicated dts node - -Since the cpuboot memory region is not part of the RAM SoC, move cpuboot -in a deidicated syscon node. -This patch helps to keep backward-compatibility with older version of -uboot codebase where we have a limit of 8 reserved-memory dts child -nodes. -Keep backward-compatibility with older dts version where cpuboot was -defined as reserved-memory child node. - -Signed-off-by: Lorenzo Bianconi ---- - drivers/net/ethernet/mediatek/mtk_wed_mcu.c | 34 +++++++++++++++++---- - drivers/net/ethernet/mediatek/mtk_wed_wo.h | 3 +- - 2 files changed, 30 insertions(+), 7 deletions(-) - ---- a/drivers/net/ethernet/mediatek/mtk_wed_mcu.c -+++ b/drivers/net/ethernet/mediatek/mtk_wed_mcu.c -@@ -34,12 +34,23 @@ static struct mtk_wed_wo_memory_region m - - static u32 wo_r32(struct mtk_wed_wo *wo, u32 reg) - { -- return readl(mem_region[MTK_WED_WO_REGION_BOOT].addr + reg); -+ u32 val; -+ -+ if (!wo->boot_regmap) -+ return readl(mem_region[MTK_WED_WO_REGION_BOOT].addr + reg); -+ -+ if (regmap_read(wo->boot_regmap, reg, &val)) -+ val = ~0; -+ -+ return val; - } - - static void wo_w32(struct mtk_wed_wo *wo, u32 reg, u32 val) - { -- writel(val, mem_region[MTK_WED_WO_REGION_BOOT].addr + reg); -+ if (wo->boot_regmap) -+ regmap_write(wo->boot_regmap, reg, val); -+ else -+ writel(val, mem_region[MTK_WED_WO_REGION_BOOT].addr + reg); - } - - static struct sk_buff * -@@ -313,6 +324,9 @@ mtk_wed_mcu_load_firmware(struct mtk_wed - u32 val, boot_cr; - int ret, i; - -+ wo->boot_regmap = syscon_regmap_lookup_by_phandle(wo->hw->node, -+ "mediatek,wo-cpuboot"); -+ - /* load firmware region metadata */ - for (i = 0; i < ARRAY_SIZE(mem_region); i++) { - int index = of_property_match_string(wo->hw->node, -@@ -321,6 +335,9 @@ mtk_wed_mcu_load_firmware(struct mtk_wed - if (index < 0) - continue; - -+ if (index == MTK_WED_WO_REGION_BOOT && !IS_ERR(wo->boot_regmap)) -+ continue; -+ - ret = mtk_wed_get_reserved_memory_region(wo->hw, index, &mem_region[i]); - if (ret) - return ret; ---- a/drivers/net/ethernet/mediatek/mtk_wed_wo.h -+++ b/drivers/net/ethernet/mediatek/mtk_wed_wo.h -@@ -231,6 +231,7 @@ struct mtk_wed_wo_queue { - struct mtk_wed_wo { - struct mtk_wed_hw *hw; - -+ struct regmap *boot_regmap; - struct mtk_wed_wo_queue q_tx; - struct mtk_wed_wo_queue q_rx; - diff --git a/target/linux/mediatek/patches-5.15/943-net-ethernet-mtk_wed-move-ilm-a-dedicated-dts-node.patch b/target/linux/mediatek/patches-5.15/943-net-ethernet-mtk_wed-move-ilm-a-dedicated-dts-node.patch deleted file mode 100644 index b4ba5b0d2d..0000000000 --- a/target/linux/mediatek/patches-5.15/943-net-ethernet-mtk_wed-move-ilm-a-dedicated-dts-node.patch +++ /dev/null @@ -1,86 +0,0 @@ -From f3565e6c2276411275e707a5442d3f69cc111273 Mon Sep 17 00:00:00 2001 -Message-Id: -From: Lorenzo Bianconi -Date: Sun, 12 Mar 2023 18:51:47 +0100 -Subject: [PATCH net-next 1/3] net: ethernet: mtk_wed: move ilm a dedicated dts - node - -Since the ilm memory region is not part of the RAM SoC, move ilm in a -deidicated syscon node. -This patch helps to keep backward-compatibility with older version of -uboot codebase where we have a limit of 8 reserved-memory dts child -nodes. -Keep backward-compatibility with older dts version where ilm was defined -as reserved-memory child node. - -Signed-off-by: Lorenzo Bianconi ---- - drivers/net/ethernet/mediatek/mtk_wed_mcu.c | 55 ++++++++++++++++++--- - 1 file changed, 49 insertions(+), 6 deletions(-) - ---- a/drivers/net/ethernet/mediatek/mtk_wed_mcu.c -+++ b/drivers/net/ethernet/mediatek/mtk_wed_mcu.c -@@ -316,6 +316,39 @@ next: - } - - static int -+mtk_wed_mcu_load_ilm(struct mtk_wed_wo *wo) -+{ -+ struct mtk_wed_wo_memory_region *ilm_region; -+ struct resource res; -+ struct device_node *np; -+ int ret; -+ -+ np = of_parse_phandle(wo->hw->node, "mediatek,wo-ilm", 0); -+ if (!np) -+ return 0; -+ -+ ret = of_address_to_resource(np, 0, &res); -+ of_node_put(np); -+ -+ if (ret < 0) -+ return ret; -+ -+ ilm_region = &mem_region[MTK_WED_WO_REGION_ILM]; -+ ilm_region->phy_addr = res.start; -+ ilm_region->size = resource_size(&res); -+ ilm_region->addr = devm_ioremap(wo->hw->dev, res.start, -+ resource_size(&res)); -+ -+ if (!IS_ERR(ilm_region->addr)) -+ return 0; -+ -+ ret = PTR_ERR(ilm_region->addr); -+ ilm_region->addr = NULL; -+ -+ return ret; -+} -+ -+static int - mtk_wed_mcu_load_firmware(struct mtk_wed_wo *wo) - { - const struct mtk_wed_fw_trailer *trailer; -@@ -324,14 +357,20 @@ mtk_wed_mcu_load_firmware(struct mtk_wed - u32 val, boot_cr; - int ret, i; - -+ mtk_wed_mcu_load_ilm(wo); - wo->boot_regmap = syscon_regmap_lookup_by_phandle(wo->hw->node, - "mediatek,wo-cpuboot"); - - /* load firmware region metadata */ - for (i = 0; i < ARRAY_SIZE(mem_region); i++) { -- int index = of_property_match_string(wo->hw->node, -- "memory-region-names", -- mem_region[i].name); -+ int index; -+ -+ if (mem_region[i].addr) -+ continue; -+ -+ index = of_property_match_string(wo->hw->node, -+ "memory-region-names", -+ mem_region[i].name); - if (index < 0) - continue; - diff --git a/target/linux/mediatek/patches-5.15/944-net-ethernet-mtk_wed-move-dlm-a-dedicated-dts-node.patch b/target/linux/mediatek/patches-5.15/944-net-ethernet-mtk_wed-move-dlm-a-dedicated-dts-node.patch deleted file mode 100644 index c92fcd43ce..0000000000 --- a/target/linux/mediatek/patches-5.15/944-net-ethernet-mtk_wed-move-dlm-a-dedicated-dts-node.patch +++ /dev/null @@ -1,57 +0,0 @@ -From b74ba226be2c45091b93bd49192bdd6d2178729e Mon Sep 17 00:00:00 2001 -Message-Id: -In-Reply-To: -References: -From: Lorenzo Bianconi -Date: Mon, 13 Mar 2023 15:45:16 +0100 -Subject: [PATCH net-next 3/3] net: ethernet: mtk_wed: move dlm a dedicated dts - node - -Since the dlm memory region is not part of the RAM SoC, move dlm in a -deidicated syscon node. -This patch helps to keep backward-compatibility with older version of -uboot codebase where we have a limit of 8 reserved-memory dts child -nodes. -Keep backward-compatibility with older dts version where dlm was defined -as reserved-memory child node. - -Signed-off-by: Lorenzo Bianconi ---- - drivers/net/ethernet/mediatek/mtk_wed.c | 19 +++++++++++++++++++ - 1 file changed, 19 insertions(+) - ---- a/drivers/net/ethernet/mediatek/mtk_wed.c -+++ b/drivers/net/ethernet/mediatek/mtk_wed.c -@@ -1320,6 +1320,24 @@ mtk_wed_rro_alloc(struct mtk_wed_device - struct device_node *np; - int index; - -+ np = of_parse_phandle(dev->hw->node, "mediatek,wo-dlm", 0); -+ if (np) { -+ struct resource res; -+ int ret; -+ -+ ret = of_address_to_resource(np, 0, &res); -+ of_node_put(np); -+ -+ if (ret < 0) -+ return ret; -+ -+ dev->rro.miod_phys = res.start; -+ goto out; -+ } -+ -+ /* For backward compatibility, we need to check if DLM -+ * node is defined through reserved memory property. -+ */ - index = of_property_match_string(dev->hw->node, "memory-region-names", - "wo-dlm"); - if (index < 0) -@@ -1336,6 +1354,7 @@ mtk_wed_rro_alloc(struct mtk_wed_device - return -ENODEV; - - dev->rro.miod_phys = rmem->base; -+out: - dev->rro.fdbk_phys = MTK_WED_MIOD_COUNT + dev->rro.miod_phys; - - return mtk_wed_rro_ring_alloc(dev, &dev->rro.ring, diff --git a/target/linux/mediatek/patches-5.15/945-arm64-dts-mt7986-move-ilm-in-a-dedicated-node.patch b/target/linux/mediatek/patches-5.15/945-arm64-dts-mt7986-move-ilm-in-a-dedicated-node.patch deleted file mode 100644 index 0ba9bd7cf0..0000000000 --- a/target/linux/mediatek/patches-5.15/945-arm64-dts-mt7986-move-ilm-in-a-dedicated-node.patch +++ /dev/null @@ -1,83 +0,0 @@ -From 01561065af5bf1d2a4244896d897e3a1eafbcd46 Mon Sep 17 00:00:00 2001 -Message-Id: <01561065af5bf1d2a4244896d897e3a1eafbcd46.1678717704.git.lorenzo@kernel.org> -From: Lorenzo Bianconi -Date: Mon, 13 Mar 2023 15:10:56 +0100 -Subject: [PATCH net-next] arm64: dts: mt7986: move ilm in a dedicated node - -Since the ilm memory region is not part of the RAM SoC, move ilm in a -deidicated syscon node. -This patch helps to keep backward-compatibility with older version of -uboot codebase where we have a limit of 8 reserved-memory dts child -nodes. - -Signed-off-by: Lorenzo Bianconi ---- - arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 34 +++++++++++------------ - 1 file changed, 16 insertions(+), 18 deletions(-) - ---- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi -@@ -97,16 +97,6 @@ - no-map; - }; - -- wo_ilm0: wo-ilm@151e0000 { -- reg = <0 0x151e0000 0 0x8000>; -- no-map; -- }; -- -- wo_ilm1: wo-ilm@151f0000 { -- reg = <0 0x151f0000 0 0x8000>; -- no-map; -- }; -- - wo_data: wo-data@4fd80000 { - reg = <0 0x4fd80000 0 0x240000>; - no-map; -@@ -533,11 +523,10 @@ - reg = <0 0x15010000 0 0x1000>; - interrupt-parent = <&gic>; - interrupts = ; -- memory-region = <&wo_emi0>, <&wo_ilm0>, <&wo_dlm0>, -- <&wo_data>; -- memory-region-names = "wo-emi", "wo-ilm", "wo-dlm", -- "wo-data"; -+ memory-region = <&wo_emi0>, <&wo_dlm0>, <&wo_data>; -+ memory-region-names = "wo-emi", "wo-dlm", "wo-data"; - mediatek,wo-ccif = <&wo_ccif0>; -+ mediatek,wo-ilm = <&wo_ilm0>; - mediatek,wo-cpuboot = <&wo_cpuboot>; - }; - -@@ -547,11 +536,10 @@ - reg = <0 0x15011000 0 0x1000>; - interrupt-parent = <&gic>; - interrupts = ; -- memory-region = <&wo_emi1>, <&wo_ilm1>, <&wo_dlm1>, -- <&wo_data>; -- memory-region-names = "wo-emi", "wo-ilm", "wo-dlm", -- "wo-data"; -+ memory-region = <&wo_emi1>, <&wo_dlm1>, <&wo_data>; -+ memory-region-names = "wo-emi", "wo-dlm", "wo-data"; - mediatek,wo-ccif = <&wo_ccif1>; -+ mediatek,wo-ilm = <&wo_ilm1>; - mediatek,wo-cpuboot = <&wo_cpuboot>; - }; - -@@ -569,6 +557,16 @@ - interrupts = ; - }; - -+ wo_ilm0: syscon@151e0000 { -+ compatible = "mediatek,mt7986-wo-ilm", "syscon"; -+ reg = <0 0x151e0000 0 0x8000>; -+ }; -+ -+ wo_ilm1: syscon@151f0000 { -+ compatible = "mediatek,mt7986-wo-ilm", "syscon"; -+ reg = <0 0x151f0000 0 0x8000>; -+ }; -+ - wo_cpuboot: syscon@15194000 { - compatible = "mediatek,mt7986-wo-cpuboot", "syscon"; - reg = <0 0x15194000 0 0x1000>; diff --git a/target/linux/mediatek/patches-5.15/946-arm64-dts-mt7986-move-dlm-in-a-dedicated-node.patch b/target/linux/mediatek/patches-5.15/946-arm64-dts-mt7986-move-dlm-in-a-dedicated-node.patch deleted file mode 100644 index 90b2bb91a2..0000000000 --- a/target/linux/mediatek/patches-5.15/946-arm64-dts-mt7986-move-dlm-in-a-dedicated-node.patch +++ /dev/null @@ -1,81 +0,0 @@ -From 9f76be683a8ec498563c294bc1cc279468058302 Mon Sep 17 00:00:00 2001 -Message-Id: <9f76be683a8ec498563c294bc1cc279468058302.1678719283.git.lorenzo@kernel.org> -From: Lorenzo Bianconi -Date: Mon, 13 Mar 2023 15:53:30 +0100 -Subject: [PATCH net-next] arm64: dts: mt7986: move dlm in a dedicated node - -Since the dlm memory region is not part of the RAM SoC, move dlm in a -deidicated syscon node. -This patch helps to keep backward-compatibility with older version of -uboot codebase where we have a limit of 8 reserved-memory dts child -nodes. - -Signed-off-by: Lorenzo Bianconi ---- - arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 30 ++++++++++++----------- - 1 file changed, 16 insertions(+), 14 deletions(-) - ---- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi -+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi -@@ -101,16 +101,6 @@ - reg = <0 0x4fd80000 0 0x240000>; - no-map; - }; -- -- wo_dlm0: wo-dlm@151e8000 { -- reg = <0 0x151e8000 0 0x2000>; -- no-map; -- }; -- -- wo_dlm1: wo-dlm@151f8000 { -- reg = <0 0x151f8000 0 0x2000>; -- no-map; -- }; - }; - - timer { -@@ -523,10 +513,11 @@ - reg = <0 0x15010000 0 0x1000>; - interrupt-parent = <&gic>; - interrupts = ; -- memory-region = <&wo_emi0>, <&wo_dlm0>, <&wo_data>; -- memory-region-names = "wo-emi", "wo-dlm", "wo-data"; -+ memory-region = <&wo_emi0>, <&wo_data>; -+ memory-region-names = "wo-emi", "wo-data"; - mediatek,wo-ccif = <&wo_ccif0>; - mediatek,wo-ilm = <&wo_ilm0>; -+ mediatek,wo-dlm = <&wo_dlm0>; - mediatek,wo-cpuboot = <&wo_cpuboot>; - }; - -@@ -536,10 +527,11 @@ - reg = <0 0x15011000 0 0x1000>; - interrupt-parent = <&gic>; - interrupts = ; -- memory-region = <&wo_emi1>, <&wo_dlm1>, <&wo_data>; -- memory-region-names = "wo-emi", "wo-dlm", "wo-data"; -+ memory-region = <&wo_emi1>, <&wo_data>; -+ memory-region-names = "wo-emi", "wo-data"; - mediatek,wo-ccif = <&wo_ccif1>; - mediatek,wo-ilm = <&wo_ilm1>; -+ mediatek,wo-dlm = <&wo_dlm1>; - mediatek,wo-cpuboot = <&wo_cpuboot>; - }; - -@@ -567,6 +559,16 @@ - reg = <0 0x151f0000 0 0x8000>; - }; - -+ wo_dlm0: syscon@151e8000 { -+ compatible = "mediatek,mt7986-wo-dlm", "syscon"; -+ reg = <0 0x151e8000 0 0x2000>; -+ }; -+ -+ wo_dlm1: syscon@151f8000 { -+ compatible = "mediatek,mt7986-wo-dlm", "syscon"; -+ reg = <0 0x151f8000 0 0x2000>; -+ }; -+ - wo_cpuboot: syscon@15194000 { - compatible = "mediatek,mt7986-wo-cpuboot", "syscon"; - reg = <0 0x15194000 0 0x1000>; diff --git a/target/linux/mediatek/patches-5.15/950-smartrg-i2c-led-driver.patch b/target/linux/mediatek/patches-5.15/950-smartrg-i2c-led-driver.patch deleted file mode 100644 index f8f1156e71..0000000000 --- a/target/linux/mediatek/patches-5.15/950-smartrg-i2c-led-driver.patch +++ /dev/null @@ -1,34 +0,0 @@ ---- - drivers/leds/Kconfig | 10 ++++++++++ - drivers/leds/Makefile | 1 + - 2 files changed, 11 insertions(+) - ---- a/drivers/leds/Kconfig -+++ b/drivers/leds/Kconfig -@@ -878,6 +878,16 @@ source "drivers/leds/blink/Kconfig" - comment "Flash and Torch LED drivers" - source "drivers/leds/flash/Kconfig" - -+config LEDS_SMARTRG_LED -+ tristate "LED support for Adtran SmartRG" -+ depends on LEDS_CLASS && I2C && OF -+ help -+ This option enables support for the Adtran SmartRG platform -+ system LED driver. -+ -+ To compile this driver as a module, choose M here: the module -+ will be called leds-smartrg-system. -+ - comment "LED Triggers" - source "drivers/leds/trigger/Kconfig" - ---- a/drivers/leds/Makefile -+++ b/drivers/leds/Makefile -@@ -77,6 +77,7 @@ obj-$(CONFIG_LEDS_PWM) += leds-pwm.o - obj-$(CONFIG_LEDS_REGULATOR) += leds-regulator.o - obj-$(CONFIG_LEDS_S3C24XX) += leds-s3c24xx.o - obj-$(CONFIG_LEDS_SC27XX_BLTC) += leds-sc27xx-bltc.o -+obj-$(CONFIG_LEDS_SMARTRG_LED) += leds-smartrg-system.o - obj-$(CONFIG_LEDS_SUNFIRE) += leds-sunfire.o - obj-$(CONFIG_LEDS_SYSCON) += leds-syscon.o - obj-$(CONFIG_LEDS_TCA6507) += leds-tca6507.o diff --git a/target/linux/mediatek/patches-5.15/961-net-ethernet-mediatek-split-tx-and-rx-fields-in-mtk_.patch b/target/linux/mediatek/patches-5.15/961-net-ethernet-mediatek-split-tx-and-rx-fields-in-mtk_.patch deleted file mode 100644 index 3b59491189..0000000000 --- a/target/linux/mediatek/patches-5.15/961-net-ethernet-mediatek-split-tx-and-rx-fields-in-mtk_.patch +++ /dev/null @@ -1,599 +0,0 @@ -From: Lorenzo Bianconi -Date: Thu, 2 Nov 2023 16:47:07 +0100 -Subject: [PATCH net-next 1/2] net: ethernet: mediatek: split tx and rx fields - in mtk_soc_data struct - -Split tx and rx fields in mtk_soc_data struct. This is a preliminary -patch to roll back to QDMA for MT7986 SoC in order to fix a hw hang -if the device receives a corrupted packet. - -Signed-off-by: Lorenzo Bianconi ---- - drivers/net/ethernet/mediatek/mtk_eth_soc.c | 210 ++++++++++++-------- - drivers/net/ethernet/mediatek/mtk_eth_soc.h | 29 +-- - 2 files changed, 139 insertions(+), 100 deletions(-) - ---- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c -+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c -@@ -1239,7 +1239,7 @@ static int mtk_init_fq_dma(struct mtk_et - eth->scratch_ring = eth->sram_base; - else - eth->scratch_ring = dma_alloc_coherent(eth->dma_dev, -- cnt * soc->txrx.txd_size, -+ cnt * soc->tx.desc_size, - ð->phy_scratch_ring, - GFP_KERNEL); - if (unlikely(!eth->scratch_ring)) -@@ -1255,16 +1255,16 @@ static int mtk_init_fq_dma(struct mtk_et - if (unlikely(dma_mapping_error(eth->dma_dev, dma_addr))) - return -ENOMEM; - -- phy_ring_tail = eth->phy_scratch_ring + soc->txrx.txd_size * (cnt - 1); -+ phy_ring_tail = eth->phy_scratch_ring + soc->tx.desc_size * (cnt - 1); - - for (i = 0; i < cnt; i++) { - struct mtk_tx_dma_v2 *txd; - -- txd = eth->scratch_ring + i * soc->txrx.txd_size; -+ txd = eth->scratch_ring + i * soc->tx.desc_size; - txd->txd1 = dma_addr + i * MTK_QDMA_PAGE_SIZE; - if (i < cnt - 1) - txd->txd2 = eth->phy_scratch_ring + -- (i + 1) * soc->txrx.txd_size; -+ (i + 1) * soc->tx.desc_size; - - txd->txd3 = TX_DMA_PLEN0(MTK_QDMA_PAGE_SIZE); - txd->txd4 = 0; -@@ -1511,7 +1511,7 @@ static int mtk_tx_map(struct sk_buff *sk - if (itxd == ring->last_free) - return -ENOMEM; - -- itx_buf = mtk_desc_to_tx_buf(ring, itxd, soc->txrx.txd_size); -+ itx_buf = mtk_desc_to_tx_buf(ring, itxd, soc->tx.desc_size); - memset(itx_buf, 0, sizeof(*itx_buf)); - - txd_info.addr = dma_map_single(eth->dma_dev, skb->data, txd_info.size, -@@ -1552,7 +1552,7 @@ static int mtk_tx_map(struct sk_buff *sk - - memset(&txd_info, 0, sizeof(struct mtk_tx_dma_desc_info)); - txd_info.size = min_t(unsigned int, frag_size, -- soc->txrx.dma_max_len); -+ soc->tx.dma_max_len); - txd_info.qid = queue; - txd_info.last = i == skb_shinfo(skb)->nr_frags - 1 && - !(frag_size - txd_info.size); -@@ -1565,7 +1565,7 @@ static int mtk_tx_map(struct sk_buff *sk - mtk_tx_set_dma_desc(dev, txd, &txd_info); - - tx_buf = mtk_desc_to_tx_buf(ring, txd, -- soc->txrx.txd_size); -+ soc->tx.desc_size); - if (new_desc) - memset(tx_buf, 0, sizeof(*tx_buf)); - tx_buf->data = (void *)MTK_DMA_DUMMY_DESC; -@@ -1608,7 +1608,7 @@ static int mtk_tx_map(struct sk_buff *sk - } else { - int next_idx; - -- next_idx = NEXT_DESP_IDX(txd_to_idx(ring, txd, soc->txrx.txd_size), -+ next_idx = NEXT_DESP_IDX(txd_to_idx(ring, txd, soc->tx.desc_size), - ring->dma_size); - mtk_w32(eth, next_idx, MT7628_TX_CTX_IDX0); - } -@@ -1617,7 +1617,7 @@ static int mtk_tx_map(struct sk_buff *sk - - err_dma: - do { -- tx_buf = mtk_desc_to_tx_buf(ring, itxd, soc->txrx.txd_size); -+ tx_buf = mtk_desc_to_tx_buf(ring, itxd, soc->tx.desc_size); - - /* unmap dma */ - mtk_tx_unmap(eth, tx_buf, false); -@@ -1642,7 +1642,7 @@ static int mtk_cal_txd_req(struct mtk_et - for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) { - frag = &skb_shinfo(skb)->frags[i]; - nfrags += DIV_ROUND_UP(skb_frag_size(frag), -- eth->soc->txrx.dma_max_len); -+ eth->soc->tx.dma_max_len); - } - } else { - nfrags += skb_shinfo(skb)->nr_frags; -@@ -1783,7 +1783,7 @@ static struct mtk_rx_ring *mtk_get_rx_ri - - ring = ð->rx_ring[i]; - idx = NEXT_DESP_IDX(ring->calc_idx, ring->dma_size); -- rxd = ring->dma + idx * eth->soc->txrx.rxd_size; -+ rxd = ring->dma + idx * eth->soc->rx.desc_size; - if (rxd->rxd2 & RX_DMA_DONE) { - ring->calc_idx_update = true; - return ring; -@@ -1951,7 +1951,7 @@ static int mtk_xdp_submit_frame(struct m - } - htxd = txd; - -- tx_buf = mtk_desc_to_tx_buf(ring, txd, soc->txrx.txd_size); -+ tx_buf = mtk_desc_to_tx_buf(ring, txd, soc->tx.desc_size); - memset(tx_buf, 0, sizeof(*tx_buf)); - htx_buf = tx_buf; - -@@ -1971,7 +1971,7 @@ static int mtk_xdp_submit_frame(struct m - goto unmap; - - tx_buf = mtk_desc_to_tx_buf(ring, txd, -- soc->txrx.txd_size); -+ soc->tx.desc_size); - memset(tx_buf, 0, sizeof(*tx_buf)); - n_desc++; - } -@@ -2008,7 +2008,7 @@ static int mtk_xdp_submit_frame(struct m - } else { - int idx; - -- idx = txd_to_idx(ring, txd, soc->txrx.txd_size); -+ idx = txd_to_idx(ring, txd, soc->tx.desc_size); - mtk_w32(eth, NEXT_DESP_IDX(idx, ring->dma_size), - MT7628_TX_CTX_IDX0); - } -@@ -2020,7 +2020,7 @@ static int mtk_xdp_submit_frame(struct m - unmap: - while (htxd != txd) { - txd_pdma = qdma_to_pdma(ring, htxd); -- tx_buf = mtk_desc_to_tx_buf(ring, htxd, soc->txrx.txd_size); -+ tx_buf = mtk_desc_to_tx_buf(ring, htxd, soc->tx.desc_size); - mtk_tx_unmap(eth, tx_buf, false); - - htxd->txd3 = TX_DMA_LS0 | TX_DMA_OWNER_CPU; -@@ -2148,7 +2148,7 @@ static int mtk_poll_rx(struct napi_struc - goto rx_done; - - idx = NEXT_DESP_IDX(ring->calc_idx, ring->dma_size); -- rxd = ring->dma + idx * eth->soc->txrx.rxd_size; -+ rxd = ring->dma + idx * eth->soc->rx.desc_size; - data = ring->data[idx]; - - if (!mtk_rx_get_desc(eth, &trxd, rxd)) -@@ -2283,7 +2283,7 @@ static int mtk_poll_rx(struct napi_struc - rxdcsum = &trxd.rxd4; - } - -- if (*rxdcsum & eth->soc->txrx.rx_dma_l4_valid) -+ if (*rxdcsum & eth->soc->rx.dma_l4_valid) - skb->ip_summed = CHECKSUM_UNNECESSARY; - else - skb_checksum_none_assert(skb); -@@ -2405,7 +2405,7 @@ static int mtk_poll_tx_qdma(struct mtk_e - break; - - tx_buf = mtk_desc_to_tx_buf(ring, desc, -- eth->soc->txrx.txd_size); -+ eth->soc->tx.desc_size); - if (!tx_buf->data) - break; - -@@ -2453,7 +2453,7 @@ static int mtk_poll_tx_pdma(struct mtk_e - } - mtk_tx_unmap(eth, tx_buf, true); - -- desc = ring->dma + cpu * eth->soc->txrx.txd_size; -+ desc = ring->dma + cpu * eth->soc->tx.desc_size; - ring->last_free = desc; - atomic_inc(&ring->free_count); - -@@ -2542,7 +2542,7 @@ static int mtk_napi_rx(struct napi_struc - do { - int rx_done; - -- mtk_w32(eth, eth->soc->txrx.rx_irq_done_mask, -+ mtk_w32(eth, eth->soc->rx.irq_done_mask, - reg_map->pdma.irq_status); - rx_done = mtk_poll_rx(napi, budget - rx_done_total, eth); - rx_done_total += rx_done; -@@ -2558,10 +2558,10 @@ static int mtk_napi_rx(struct napi_struc - return budget; - - } while (mtk_r32(eth, reg_map->pdma.irq_status) & -- eth->soc->txrx.rx_irq_done_mask); -+ eth->soc->rx.irq_done_mask); - - if (napi_complete_done(napi, rx_done_total)) -- mtk_rx_irq_enable(eth, eth->soc->txrx.rx_irq_done_mask); -+ mtk_rx_irq_enable(eth, eth->soc->rx.irq_done_mask); - - return rx_done_total; - } -@@ -2570,7 +2570,7 @@ static int mtk_tx_alloc(struct mtk_eth * - { - const struct mtk_soc_data *soc = eth->soc; - struct mtk_tx_ring *ring = ð->tx_ring; -- int i, sz = soc->txrx.txd_size; -+ int i, sz = soc->tx.desc_size; - struct mtk_tx_dma_v2 *txd; - int ring_size; - u32 ofs, val; -@@ -2693,14 +2693,14 @@ static void mtk_tx_clean(struct mtk_eth - } - if (!MTK_HAS_CAPS(soc->caps, MTK_SRAM) && ring->dma) { - dma_free_coherent(eth->dma_dev, -- ring->dma_size * soc->txrx.txd_size, -+ ring->dma_size * soc->tx.desc_size, - ring->dma, ring->phys); - ring->dma = NULL; - } - - if (ring->dma_pdma) { - dma_free_coherent(eth->dma_dev, -- ring->dma_size * soc->txrx.txd_size, -+ ring->dma_size * soc->tx.desc_size, - ring->dma_pdma, ring->phys_pdma); - ring->dma_pdma = NULL; - } -@@ -2755,15 +2755,15 @@ static int mtk_rx_alloc(struct mtk_eth * - if (!MTK_HAS_CAPS(eth->soc->caps, MTK_SRAM) || - rx_flag != MTK_RX_FLAGS_NORMAL) { - ring->dma = dma_alloc_coherent(eth->dma_dev, -- rx_dma_size * eth->soc->txrx.rxd_size, -- &ring->phys, GFP_KERNEL); -+ rx_dma_size * eth->soc->rx.desc_size, -+ &ring->phys, GFP_KERNEL); - } else { - struct mtk_tx_ring *tx_ring = ð->tx_ring; - - ring->dma = tx_ring->dma + tx_ring_size * -- eth->soc->txrx.txd_size * (ring_no + 1); -+ eth->soc->tx.desc_size * (ring_no + 1); - ring->phys = tx_ring->phys + tx_ring_size * -- eth->soc->txrx.txd_size * (ring_no + 1); -+ eth->soc->tx.desc_size * (ring_no + 1); - } - - if (!ring->dma) -@@ -2774,7 +2774,7 @@ static int mtk_rx_alloc(struct mtk_eth * - dma_addr_t dma_addr; - void *data; - -- rxd = ring->dma + i * eth->soc->txrx.rxd_size; -+ rxd = ring->dma + i * eth->soc->rx.desc_size; - if (ring->page_pool) { - data = mtk_page_pool_get_buff(ring->page_pool, - &dma_addr, GFP_KERNEL); -@@ -2863,7 +2863,7 @@ static void mtk_rx_clean(struct mtk_eth - if (!ring->data[i]) - continue; - -- rxd = ring->dma + i * eth->soc->txrx.rxd_size; -+ rxd = ring->dma + i * eth->soc->rx.desc_size; - if (!rxd->rxd1) - continue; - -@@ -2880,7 +2880,7 @@ static void mtk_rx_clean(struct mtk_eth - - if (!in_sram && ring->dma) { - dma_free_coherent(eth->dma_dev, -- ring->dma_size * eth->soc->txrx.rxd_size, -+ ring->dma_size * eth->soc->rx.desc_size, - ring->dma, ring->phys); - ring->dma = NULL; - } -@@ -3243,7 +3243,7 @@ static void mtk_dma_free(struct mtk_eth - netdev_reset_queue(eth->netdev[i]); - if (!MTK_HAS_CAPS(soc->caps, MTK_SRAM) && eth->scratch_ring) { - dma_free_coherent(eth->dma_dev, -- MTK_QDMA_RING_SIZE * soc->txrx.txd_size, -+ MTK_QDMA_RING_SIZE * soc->tx.desc_size, - eth->scratch_ring, eth->phy_scratch_ring); - eth->scratch_ring = NULL; - eth->phy_scratch_ring = 0; -@@ -3293,7 +3293,7 @@ static irqreturn_t mtk_handle_irq_rx(int - - eth->rx_events++; - if (likely(napi_schedule_prep(ð->rx_napi))) { -- mtk_rx_irq_disable(eth, eth->soc->txrx.rx_irq_done_mask); -+ mtk_rx_irq_disable(eth, eth->soc->rx.irq_done_mask); - __napi_schedule(ð->rx_napi); - } - -@@ -3319,9 +3319,9 @@ static irqreturn_t mtk_handle_irq(int ir - const struct mtk_reg_map *reg_map = eth->soc->reg_map; - - if (mtk_r32(eth, reg_map->pdma.irq_mask) & -- eth->soc->txrx.rx_irq_done_mask) { -+ eth->soc->rx.irq_done_mask) { - if (mtk_r32(eth, reg_map->pdma.irq_status) & -- eth->soc->txrx.rx_irq_done_mask) -+ eth->soc->rx.irq_done_mask) - mtk_handle_irq_rx(irq, _eth); - } - if (mtk_r32(eth, reg_map->tx_irq_mask) & MTK_TX_DONE_INT) { -@@ -3339,10 +3339,10 @@ static void mtk_poll_controller(struct n - struct mtk_eth *eth = mac->hw; - - mtk_tx_irq_disable(eth, MTK_TX_DONE_INT); -- mtk_rx_irq_disable(eth, eth->soc->txrx.rx_irq_done_mask); -+ mtk_rx_irq_disable(eth, eth->soc->rx.irq_done_mask); - mtk_handle_irq_rx(eth->irq[2], dev); - mtk_tx_irq_enable(eth, MTK_TX_DONE_INT); -- mtk_rx_irq_enable(eth, eth->soc->txrx.rx_irq_done_mask); -+ mtk_rx_irq_enable(eth, eth->soc->rx.irq_done_mask); - } - #endif - -@@ -3507,7 +3507,7 @@ static int mtk_open(struct net_device *d - napi_enable(ð->tx_napi); - napi_enable(ð->rx_napi); - mtk_tx_irq_enable(eth, MTK_TX_DONE_INT); -- mtk_rx_irq_enable(eth, soc->txrx.rx_irq_done_mask); -+ mtk_rx_irq_enable(eth, soc->rx.irq_done_mask); - refcount_set(ð->dma_refcnt, 1); - } - else -@@ -3590,7 +3590,7 @@ static int mtk_stop(struct net_device *d - mtk_gdm_config(eth, MTK_GDMA_DROP_ALL); - - mtk_tx_irq_disable(eth, MTK_TX_DONE_INT); -- mtk_rx_irq_disable(eth, eth->soc->txrx.rx_irq_done_mask); -+ mtk_rx_irq_disable(eth, eth->soc->rx.irq_done_mask); - napi_disable(ð->tx_napi); - napi_disable(ð->rx_napi); - -@@ -4066,9 +4066,9 @@ static int mtk_hw_init(struct mtk_eth *e - - /* FE int grouping */ - mtk_w32(eth, MTK_TX_DONE_INT, reg_map->pdma.int_grp); -- mtk_w32(eth, eth->soc->txrx.rx_irq_done_mask, reg_map->pdma.int_grp + 4); -+ mtk_w32(eth, eth->soc->rx.irq_done_mask, reg_map->pdma.int_grp + 4); - mtk_w32(eth, MTK_TX_DONE_INT, reg_map->qdma.int_grp); -- mtk_w32(eth, eth->soc->txrx.rx_irq_done_mask, reg_map->qdma.int_grp + 4); -+ mtk_w32(eth, eth->soc->rx.irq_done_mask, reg_map->qdma.int_grp + 4); - mtk_w32(eth, 0x21021000, MTK_FE_INT_GRP); - - if (mtk_is_netsys_v3_or_greater(eth)) { -@@ -5168,11 +5168,15 @@ static const struct mtk_soc_data mt2701_ - .required_clks = MT7623_CLKS_BITMAP, - .required_pctl = true, - .version = 1, -- .txrx = { -- .txd_size = sizeof(struct mtk_tx_dma), -- .rxd_size = sizeof(struct mtk_rx_dma), -- .rx_irq_done_mask = MTK_RX_DONE_INT, -- .rx_dma_l4_valid = RX_DMA_L4_VALID, -+ .tx = { -+ .desc_size = sizeof(struct mtk_tx_dma), -+ .dma_max_len = MTK_TX_DMA_BUF_LEN, -+ .dma_len_offset = 16, -+ }, -+ .rx = { -+ .desc_size = sizeof(struct mtk_rx_dma), -+ .irq_done_mask = MTK_RX_DONE_INT, -+ .dma_l4_valid = RX_DMA_L4_VALID, - .dma_max_len = MTK_TX_DMA_BUF_LEN, - .dma_len_offset = 16, - }, -@@ -5188,11 +5192,15 @@ static const struct mtk_soc_data mt7621_ - .offload_version = 1, - .hash_offset = 2, - .foe_entry_size = MTK_FOE_ENTRY_V1_SIZE, -- .txrx = { -- .txd_size = sizeof(struct mtk_tx_dma), -- .rxd_size = sizeof(struct mtk_rx_dma), -- .rx_irq_done_mask = MTK_RX_DONE_INT, -- .rx_dma_l4_valid = RX_DMA_L4_VALID, -+ .tx = { -+ .desc_size = sizeof(struct mtk_tx_dma), -+ .dma_max_len = MTK_TX_DMA_BUF_LEN, -+ .dma_len_offset = 16, -+ }, -+ .rx = { -+ .desc_size = sizeof(struct mtk_rx_dma), -+ .irq_done_mask = MTK_RX_DONE_INT, -+ .dma_l4_valid = RX_DMA_L4_VALID, - .dma_max_len = MTK_TX_DMA_BUF_LEN, - .dma_len_offset = 16, - }, -@@ -5210,11 +5218,15 @@ static const struct mtk_soc_data mt7622_ - .hash_offset = 2, - .has_accounting = true, - .foe_entry_size = MTK_FOE_ENTRY_V1_SIZE, -- .txrx = { -- .txd_size = sizeof(struct mtk_tx_dma), -- .rxd_size = sizeof(struct mtk_rx_dma), -- .rx_irq_done_mask = MTK_RX_DONE_INT, -- .rx_dma_l4_valid = RX_DMA_L4_VALID, -+ .tx = { -+ .desc_size = sizeof(struct mtk_tx_dma), -+ .dma_max_len = MTK_TX_DMA_BUF_LEN, -+ .dma_len_offset = 16, -+ }, -+ .rx = { -+ .desc_size = sizeof(struct mtk_rx_dma), -+ .irq_done_mask = MTK_RX_DONE_INT, -+ .dma_l4_valid = RX_DMA_L4_VALID, - .dma_max_len = MTK_TX_DMA_BUF_LEN, - .dma_len_offset = 16, - }, -@@ -5231,11 +5243,15 @@ static const struct mtk_soc_data mt7623_ - .hash_offset = 2, - .foe_entry_size = MTK_FOE_ENTRY_V1_SIZE, - .disable_pll_modes = true, -- .txrx = { -- .txd_size = sizeof(struct mtk_tx_dma), -- .rxd_size = sizeof(struct mtk_rx_dma), -- .rx_irq_done_mask = MTK_RX_DONE_INT, -- .rx_dma_l4_valid = RX_DMA_L4_VALID, -+ .tx = { -+ .desc_size = sizeof(struct mtk_tx_dma), -+ .dma_max_len = MTK_TX_DMA_BUF_LEN, -+ .dma_len_offset = 16, -+ }, -+ .rx = { -+ .desc_size = sizeof(struct mtk_rx_dma), -+ .irq_done_mask = MTK_RX_DONE_INT, -+ .dma_l4_valid = RX_DMA_L4_VALID, - .dma_max_len = MTK_TX_DMA_BUF_LEN, - .dma_len_offset = 16, - }, -@@ -5250,11 +5266,15 @@ static const struct mtk_soc_data mt7629_ - .required_pctl = false, - .has_accounting = true, - .version = 1, -- .txrx = { -- .txd_size = sizeof(struct mtk_tx_dma), -- .rxd_size = sizeof(struct mtk_rx_dma), -- .rx_irq_done_mask = MTK_RX_DONE_INT, -- .rx_dma_l4_valid = RX_DMA_L4_VALID, -+ .tx = { -+ .desc_size = sizeof(struct mtk_tx_dma), -+ .dma_max_len = MTK_TX_DMA_BUF_LEN, -+ .dma_len_offset = 16, -+ }, -+ .rx = { -+ .desc_size = sizeof(struct mtk_rx_dma), -+ .irq_done_mask = MTK_RX_DONE_INT, -+ .dma_l4_valid = RX_DMA_L4_VALID, - .dma_max_len = MTK_TX_DMA_BUF_LEN, - .dma_len_offset = 16, - }, -@@ -5272,11 +5292,15 @@ static const struct mtk_soc_data mt7981_ - .hash_offset = 4, - .has_accounting = true, - .foe_entry_size = MTK_FOE_ENTRY_V2_SIZE, -- .txrx = { -- .txd_size = sizeof(struct mtk_tx_dma_v2), -- .rxd_size = sizeof(struct mtk_rx_dma_v2), -- .rx_irq_done_mask = MTK_RX_DONE_INT_V2, -- .rx_dma_l4_valid = RX_DMA_L4_VALID_V2, -+ .tx = { -+ .desc_size = sizeof(struct mtk_tx_dma_v2), -+ .dma_max_len = MTK_TX_DMA_BUF_LEN_V2, -+ .dma_len_offset = 8, -+ }, -+ .rx = { -+ .desc_size = sizeof(struct mtk_rx_dma_v2), -+ .irq_done_mask = MTK_RX_DONE_INT_V2, -+ .dma_l4_valid = RX_DMA_L4_VALID_V2, - .dma_max_len = MTK_TX_DMA_BUF_LEN_V2, - .dma_len_offset = 8, - }, -@@ -5294,11 +5318,15 @@ static const struct mtk_soc_data mt7986_ - .hash_offset = 4, - .has_accounting = true, - .foe_entry_size = MTK_FOE_ENTRY_V2_SIZE, -- .txrx = { -- .txd_size = sizeof(struct mtk_tx_dma_v2), -- .rxd_size = sizeof(struct mtk_rx_dma_v2), -- .rx_irq_done_mask = MTK_RX_DONE_INT_V2, -- .rx_dma_l4_valid = RX_DMA_L4_VALID_V2, -+ .tx = { -+ .desc_size = sizeof(struct mtk_tx_dma_v2), -+ .dma_max_len = MTK_TX_DMA_BUF_LEN_V2, -+ .dma_len_offset = 8, -+ }, -+ .rx = { -+ .desc_size = sizeof(struct mtk_rx_dma_v2), -+ .irq_done_mask = MTK_RX_DONE_INT_V2, -+ .dma_l4_valid = RX_DMA_L4_VALID_V2, - .dma_max_len = MTK_TX_DMA_BUF_LEN_V2, - .dma_len_offset = 8, - }, -@@ -5316,11 +5344,15 @@ static const struct mtk_soc_data mt7988_ - .hash_offset = 4, - .has_accounting = true, - .foe_entry_size = MTK_FOE_ENTRY_V3_SIZE, -- .txrx = { -- .txd_size = sizeof(struct mtk_tx_dma_v2), -- .rxd_size = sizeof(struct mtk_rx_dma_v2), -- .rx_irq_done_mask = MTK_RX_DONE_INT_V2, -- .rx_dma_l4_valid = RX_DMA_L4_VALID_V2, -+ .tx = { -+ .desc_size = sizeof(struct mtk_tx_dma_v2), -+ .dma_max_len = MTK_TX_DMA_BUF_LEN_V2, -+ .dma_len_offset = 8, -+ }, -+ .rx = { -+ .desc_size = sizeof(struct mtk_rx_dma_v2), -+ .irq_done_mask = MTK_RX_DONE_INT_V2, -+ .dma_l4_valid = RX_DMA_L4_VALID_V2, - .dma_max_len = MTK_TX_DMA_BUF_LEN_V2, - .dma_len_offset = 8, - }, -@@ -5333,11 +5365,15 @@ static const struct mtk_soc_data rt5350_ - .required_clks = MT7628_CLKS_BITMAP, - .required_pctl = false, - .version = 1, -- .txrx = { -- .txd_size = sizeof(struct mtk_tx_dma), -- .rxd_size = sizeof(struct mtk_rx_dma), -- .rx_irq_done_mask = MTK_RX_DONE_INT, -- .rx_dma_l4_valid = RX_DMA_L4_VALID_PDMA, -+ .tx = { -+ .desc_size = sizeof(struct mtk_tx_dma), -+ .dma_max_len = MTK_TX_DMA_BUF_LEN, -+ .dma_len_offset = 16, -+ }, -+ .rx = { -+ .desc_size = sizeof(struct mtk_rx_dma), -+ .irq_done_mask = MTK_RX_DONE_INT, -+ .dma_l4_valid = RX_DMA_L4_VALID_PDMA, - .dma_max_len = MTK_TX_DMA_BUF_LEN, - .dma_len_offset = 16, - }, ---- a/drivers/net/ethernet/mediatek/mtk_eth_soc.h -+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.h -@@ -326,8 +326,8 @@ - /* QDMA descriptor txd3 */ - #define TX_DMA_OWNER_CPU BIT(31) - #define TX_DMA_LS0 BIT(30) --#define TX_DMA_PLEN0(x) (((x) & eth->soc->txrx.dma_max_len) << eth->soc->txrx.dma_len_offset) --#define TX_DMA_PLEN1(x) ((x) & eth->soc->txrx.dma_max_len) -+#define TX_DMA_PLEN0(x) (((x) & eth->soc->tx.dma_max_len) << eth->soc->tx.dma_len_offset) -+#define TX_DMA_PLEN1(x) ((x) & eth->soc->tx.dma_max_len) - #define TX_DMA_SWC BIT(14) - #define TX_DMA_PQID GENMASK(3, 0) - #define TX_DMA_ADDR64_MASK GENMASK(3, 0) -@@ -347,8 +347,8 @@ - /* QDMA descriptor rxd2 */ - #define RX_DMA_DONE BIT(31) - #define RX_DMA_LSO BIT(30) --#define RX_DMA_PREP_PLEN0(x) (((x) & eth->soc->txrx.dma_max_len) << eth->soc->txrx.dma_len_offset) --#define RX_DMA_GET_PLEN0(x) (((x) >> eth->soc->txrx.dma_len_offset) & eth->soc->txrx.dma_max_len) -+#define RX_DMA_PREP_PLEN0(x) (((x) & eth->soc->rx.dma_max_len) << eth->soc->rx.dma_len_offset) -+#define RX_DMA_GET_PLEN0(x) (((x) >> eth->soc->rx.dma_len_offset) & eth->soc->rx.dma_max_len) - #define RX_DMA_VTAG BIT(15) - #define RX_DMA_ADDR64_MASK GENMASK(3, 0) - #if IS_ENABLED(CONFIG_64BIT) -@@ -1279,10 +1279,9 @@ struct mtk_reg_map { - * @foe_entry_size Foe table entry size. - * @has_accounting Bool indicating support for accounting of - * offloaded flows. -- * @txd_size Tx DMA descriptor size. -- * @rxd_size Rx DMA descriptor size. -- * @rx_irq_done_mask Rx irq done register mask. -- * @rx_dma_l4_valid Rx DMA valid register mask. -+ * @desc_size Tx/Rx DMA descriptor size. -+ * @irq_done_mask Rx irq done register mask. -+ * @dma_l4_valid Rx DMA valid register mask. - * @dma_max_len Max DMA tx/rx buffer length. - * @dma_len_offset Tx/Rx DMA length field offset. - */ -@@ -1300,13 +1299,17 @@ struct mtk_soc_data { - bool has_accounting; - bool disable_pll_modes; - struct { -- u32 txd_size; -- u32 rxd_size; -- u32 rx_irq_done_mask; -- u32 rx_dma_l4_valid; -+ u32 desc_size; - u32 dma_max_len; - u32 dma_len_offset; -- } txrx; -+ } tx; -+ struct { -+ u32 desc_size; -+ u32 irq_done_mask; -+ u32 dma_l4_valid; -+ u32 dma_max_len; -+ u32 dma_len_offset; -+ } rx; - }; - - #define MTK_DMA_MONITOR_TIMEOUT msecs_to_jiffies(1000) diff --git a/target/linux/mediatek/patches-5.15/962-net-ethernet-mediatek-use-QDMA-instead-of-ADMAv2-on-.patch b/target/linux/mediatek/patches-5.15/962-net-ethernet-mediatek-use-QDMA-instead-of-ADMAv2-on-.patch deleted file mode 100644 index 3d4d68cb81..0000000000 --- a/target/linux/mediatek/patches-5.15/962-net-ethernet-mediatek-use-QDMA-instead-of-ADMAv2-on-.patch +++ /dev/null @@ -1,123 +0,0 @@ -From: Daniel Golle -Date: Tue, 10 Oct 2023 21:06:43 +0200 -Subject: [PATCH net-next 2/2] net: ethernet: mediatek: use QDMA instead of - ADMAv2 on MT7981 and MT7986 - -ADMA is plagued by RX hangs which can't easily detected and happen upon -receival of a corrupted package. -Use QDMA just like on netsys v1 which is also still present and usable, and -doesn't suffer from that problem. - -Co-developed-by: Lorenzo Bianconi -Signed-off-by: Lorenzo Bianconi -Signed-off-by: Daniel Golle ---- - drivers/net/ethernet/mediatek/mtk_eth_soc.c | 46 ++++++++++----------- - 1 file changed, 23 insertions(+), 23 deletions(-) - ---- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c -+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c -@@ -108,16 +108,16 @@ static const struct mtk_reg_map mt7986_r - .tx_irq_mask = 0x461c, - .tx_irq_status = 0x4618, - .pdma = { -- .rx_ptr = 0x6100, -- .rx_cnt_cfg = 0x6104, -- .pcrx_ptr = 0x6108, -- .glo_cfg = 0x6204, -- .rst_idx = 0x6208, -- .delay_irq = 0x620c, -- .irq_status = 0x6220, -- .irq_mask = 0x6228, -- .adma_rx_dbg0 = 0x6238, -- .int_grp = 0x6250, -+ .rx_ptr = 0x4100, -+ .rx_cnt_cfg = 0x4104, -+ .pcrx_ptr = 0x4108, -+ .glo_cfg = 0x4204, -+ .rst_idx = 0x4208, -+ .delay_irq = 0x420c, -+ .irq_status = 0x4220, -+ .irq_mask = 0x4228, -+ .adma_rx_dbg0 = 0x4238, -+ .int_grp = 0x4250, - }, - .qdma = { - .qtx_cfg = 0x4400, -@@ -1207,7 +1207,7 @@ static bool mtk_rx_get_desc(struct mtk_e - rxd->rxd1 = READ_ONCE(dma_rxd->rxd1); - rxd->rxd3 = READ_ONCE(dma_rxd->rxd3); - rxd->rxd4 = READ_ONCE(dma_rxd->rxd4); -- if (mtk_is_netsys_v2_or_greater(eth)) { -+ if (mtk_is_netsys_v3_or_greater(eth)) { - rxd->rxd5 = READ_ONCE(dma_rxd->rxd5); - rxd->rxd6 = READ_ONCE(dma_rxd->rxd6); - } -@@ -2155,7 +2155,7 @@ static int mtk_poll_rx(struct napi_struc - break; - - /* find out which mac the packet come from. values start at 1 */ -- if (mtk_is_netsys_v2_or_greater(eth)) { -+ if (mtk_is_netsys_v3_or_greater(eth)) { - u32 val = RX_DMA_GET_SPORT_V2(trxd.rxd5); - - switch (val) { -@@ -2267,7 +2267,7 @@ static int mtk_poll_rx(struct napi_struc - skb->dev = netdev; - bytes += skb->len; - -- if (mtk_is_netsys_v2_or_greater(eth)) { -+ if (mtk_is_netsys_v3_or_greater(eth)) { - reason = FIELD_GET(MTK_RXD5_PPE_CPU_REASON, trxd.rxd5); - hash = trxd.rxd5 & MTK_RXD5_FOE_ENTRY; - if (hash != MTK_RXD5_FOE_ENTRY) -@@ -2809,7 +2809,7 @@ static int mtk_rx_alloc(struct mtk_eth * - - rxd->rxd3 = 0; - rxd->rxd4 = 0; -- if (mtk_is_netsys_v2_or_greater(eth)) { -+ if (mtk_is_netsys_v3_or_greater(eth)) { - rxd->rxd5 = 0; - rxd->rxd6 = 0; - rxd->rxd7 = 0; -@@ -4012,7 +4012,7 @@ static int mtk_hw_init(struct mtk_eth *e - else - mtk_hw_reset(eth); - -- if (mtk_is_netsys_v2_or_greater(eth)) { -+ if (mtk_is_netsys_v3_or_greater(eth)) { - /* Set FE to PDMAv2 if necessary */ - val = mtk_r32(eth, MTK_FE_GLO_MISC); - mtk_w32(eth, val | BIT(4), MTK_FE_GLO_MISC); -@@ -5298,11 +5298,11 @@ static const struct mtk_soc_data mt7981_ - .dma_len_offset = 8, - }, - .rx = { -- .desc_size = sizeof(struct mtk_rx_dma_v2), -- .irq_done_mask = MTK_RX_DONE_INT_V2, -+ .desc_size = sizeof(struct mtk_rx_dma), -+ .irq_done_mask = MTK_RX_DONE_INT, - .dma_l4_valid = RX_DMA_L4_VALID_V2, -- .dma_max_len = MTK_TX_DMA_BUF_LEN_V2, -- .dma_len_offset = 8, -+ .dma_max_len = MTK_TX_DMA_BUF_LEN, -+ .dma_len_offset = 16, - }, - }; - -@@ -5324,11 +5324,11 @@ static const struct mtk_soc_data mt7986_ - .dma_len_offset = 8, - }, - .rx = { -- .desc_size = sizeof(struct mtk_rx_dma_v2), -- .irq_done_mask = MTK_RX_DONE_INT_V2, -+ .desc_size = sizeof(struct mtk_rx_dma), -+ .irq_done_mask = MTK_RX_DONE_INT, - .dma_l4_valid = RX_DMA_L4_VALID_V2, -- .dma_max_len = MTK_TX_DMA_BUF_LEN_V2, -- .dma_len_offset = 8, -+ .dma_max_len = MTK_TX_DMA_BUF_LEN, -+ .dma_len_offset = 16, - }, - }; - diff --git a/target/linux/mediatek/patches-5.15/963-net-ethernet-mtk_eth_soc-fix-WED-wifi-reset.patch b/target/linux/mediatek/patches-5.15/963-net-ethernet-mtk_eth_soc-fix-WED-wifi-reset.patch deleted file mode 100644 index 11b52d07ab..0000000000 --- a/target/linux/mediatek/patches-5.15/963-net-ethernet-mtk_eth_soc-fix-WED-wifi-reset.patch +++ /dev/null @@ -1,49 +0,0 @@ -From: Felix Fietkau -Date: Thu, 18 Jan 2024 12:51:32 +0100 -Subject: [PATCH] net: ethernet: mtk_eth_soc: fix WED + wifi reset - -The WLAN + WED reset sequence relies on being able to receive interrupts from -the card, in order to synchronize individual steps with the firmware. -When WED is stopped, leave interrupts running and rely on the driver turning -off unwanted ones. -WED DMA also needs to be disabled before resetting. - -Fixes: f78cd9c783e0 ("net: ethernet: mtk_wed: update mtk_wed_stop") -Signed-off-by: Felix Fietkau ---- - ---- a/drivers/net/ethernet/mediatek/mtk_wed.c -+++ b/drivers/net/ethernet/mediatek/mtk_wed.c -@@ -1071,13 +1071,13 @@ mtk_wed_dma_disable(struct mtk_wed_devic - static void - mtk_wed_stop(struct mtk_wed_device *dev) - { -+ mtk_wed_dma_disable(dev); - mtk_wed_set_ext_int(dev, false); - - wed_w32(dev, MTK_WED_WPDMA_INT_TRIGGER, 0); - wed_w32(dev, MTK_WED_WDMA_INT_TRIGGER, 0); - wdma_w32(dev, MTK_WDMA_INT_MASK, 0); - wdma_w32(dev, MTK_WDMA_INT_GRP2, 0); -- wed_w32(dev, MTK_WED_WPDMA_INT_MASK, 0); - - if (!mtk_wed_get_rx_capa(dev)) - return; -@@ -1090,7 +1090,6 @@ static void - mtk_wed_deinit(struct mtk_wed_device *dev) - { - mtk_wed_stop(dev); -- mtk_wed_dma_disable(dev); - - wed_clr(dev, MTK_WED_CTRL, - MTK_WED_CTRL_WDMA_INT_AGENT_EN | -@@ -2621,9 +2620,6 @@ mtk_wed_irq_get(struct mtk_wed_device *d - static void - mtk_wed_irq_set_mask(struct mtk_wed_device *dev, u32 mask) - { -- if (!dev->running) -- return; -- - mtk_wed_set_ext_int(dev, !!mask); - wed_w32(dev, MTK_WED_INT_MASK, mask); - } -- 2.30.2