From f7cac0484d35696acae31a3db9cb9b2271c0b1e5 Mon Sep 17 00:00:00 2001 From: Daniel Golle Date: Tue, 30 May 2023 02:44:00 +0100 Subject: [PATCH] kernel: backport MT7988 DSA support for Linux 6.1 Patches adding DSA support for MT7988 have been backported to Linux 5.15 but not to Linux 6.1. Import backports also to Linux 6.1. Signed-off-by: Daniel Golle --- ...ake-some-noise-if-register-read-fail.patch | 32 + ...a-mt7530-refactor-SGMII-PCS-creation.patch | 111 +++ ...mt7530-use-unlocked-regmap-accessors.patch | 74 ++ ...se-regmap-to-access-switch-register-.patch | 224 ++++++ ...ove-SGMII-PCS-creation-to-mt7530_pro.patch | 54 ++ ...t-dsa-mt7530-introduce-mutex-helpers.patch | 273 +++++++ ...ove-p5_intf_modes-function-to-mt7530.patch | 75 ++ ...ntroduce-mt7530_probe_common-helper-.patch | 155 ++++ ...ntroduce-mt7530_remove_common-helper.patch | 54 ++ ...t7530-introduce-separate-MDIO-driver.patch | 691 ++++++++++++++++++ ...kip-locking-if-MDIO-bus-isn-t-presen.patch | 47 ++ ...ntroduce-driver-for-MT7988-built-in-.patch | 421 +++++++++++ ...-dsa-mt7530-fix-support-for-MT7531BE.patch | 118 +++ ...or-Motorcomm-yt8521-gigabit-ethernet.patch | 2 +- ...e-all-MACs-are-powered-down-before-r.patch | 2 +- ...gister-OF-node-for-internal-MDIO-bus.patch | 4 +- 16 files changed, 2333 insertions(+), 4 deletions(-) create mode 100644 target/linux/generic/backport-6.1/790-v6.4-0001-net-dsa-mt7530-make-some-noise-if-register-read-fail.patch create mode 100644 target/linux/generic/backport-6.1/790-v6.4-0002-net-dsa-mt7530-refactor-SGMII-PCS-creation.patch create mode 100644 target/linux/generic/backport-6.1/790-v6.4-0003-net-dsa-mt7530-use-unlocked-regmap-accessors.patch create mode 100644 target/linux/generic/backport-6.1/790-v6.4-0004-net-dsa-mt7530-use-regmap-to-access-switch-register-.patch create mode 100644 target/linux/generic/backport-6.1/790-v6.4-0005-net-dsa-mt7530-move-SGMII-PCS-creation-to-mt7530_pro.patch create mode 100644 target/linux/generic/backport-6.1/790-v6.4-0006-net-dsa-mt7530-introduce-mutex-helpers.patch create mode 100644 target/linux/generic/backport-6.1/790-v6.4-0007-net-dsa-mt7530-move-p5_intf_modes-function-to-mt7530.patch create mode 100644 target/linux/generic/backport-6.1/790-v6.4-0008-net-dsa-mt7530-introduce-mt7530_probe_common-helper-.patch create mode 100644 target/linux/generic/backport-6.1/790-v6.4-0009-net-dsa-mt7530-introduce-mt7530_remove_common-helper.patch create mode 100644 target/linux/generic/backport-6.1/790-v6.4-0010-net-dsa-mt7530-introduce-separate-MDIO-driver.patch create mode 100644 target/linux/generic/backport-6.1/790-v6.4-0011-net-dsa-mt7530-skip-locking-if-MDIO-bus-isn-t-presen.patch create mode 100644 target/linux/generic/backport-6.1/790-v6.4-0012-net-dsa-mt7530-introduce-driver-for-MT7988-built-in-.patch create mode 100644 target/linux/generic/backport-6.1/790-v6.4-0013-net-dsa-mt7530-fix-support-for-MT7531BE.patch diff --git a/target/linux/generic/backport-6.1/790-v6.4-0001-net-dsa-mt7530-make-some-noise-if-register-read-fail.patch b/target/linux/generic/backport-6.1/790-v6.4-0001-net-dsa-mt7530-make-some-noise-if-register-read-fail.patch new file mode 100644 index 0000000000..4d024b063a --- /dev/null +++ b/target/linux/generic/backport-6.1/790-v6.4-0001-net-dsa-mt7530-make-some-noise-if-register-read-fail.patch @@ -0,0 +1,32 @@ +From c3552d3f85f06cf4b4818bd84c4fcc09d8d45165 Mon Sep 17 00:00:00 2001 +From: Daniel Golle +Date: Mon, 3 Apr 2023 02:17:19 +0100 +Subject: [PATCH 01/13] net: dsa: mt7530: make some noise if register read + fails + +Simply returning the negative error value instead of the read value +doesn't seem like a good idea. Return 0 instead and add WARN_ON_ONCE(1) +so this kind of error will not go unnoticed. + +Suggested-by: Andrew Lunn +Signed-off-by: Daniel Golle +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/mt7530.c | 3 ++- + 1 file changed, 2 insertions(+), 1 deletion(-) + +--- a/drivers/net/dsa/mt7530.c ++++ b/drivers/net/dsa/mt7530.c +@@ -224,9 +224,10 @@ mt7530_mii_read(struct mt7530_priv *priv + /* MT7530 uses 31 as the pseudo port */ + ret = bus->write(bus, 0x1f, 0x1f, page); + if (ret < 0) { ++ WARN_ON_ONCE(1); + dev_err(&bus->dev, + "failed to read mt7530 register\n"); +- return ret; ++ return 0; + } + + lo = bus->read(bus, 0x1f, r); diff --git a/target/linux/generic/backport-6.1/790-v6.4-0002-net-dsa-mt7530-refactor-SGMII-PCS-creation.patch b/target/linux/generic/backport-6.1/790-v6.4-0002-net-dsa-mt7530-refactor-SGMII-PCS-creation.patch new file mode 100644 index 0000000000..4f255abc5b --- /dev/null +++ b/target/linux/generic/backport-6.1/790-v6.4-0002-net-dsa-mt7530-refactor-SGMII-PCS-creation.patch @@ -0,0 +1,111 @@ +From b896355fc4988216d4f38582d07add9252a795ae Mon Sep 17 00:00:00 2001 +From: Daniel Golle +Date: Mon, 3 Apr 2023 02:17:30 +0100 +Subject: [PATCH 02/13] net: dsa: mt7530: refactor SGMII PCS creation + +Instead of macro templates use a dedidated function and allocated +regmap_config when creating the regmaps for the pcs-mtk-lynxi +instances. +This is in preparation to switching to use unlocked regmap accessors +and have regmap's locking API handle locking for us. + +Signed-off-by: Daniel Golle +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/mt7530.c | 74 +++++++++++++++++++++++++++------------- + 1 file changed, 50 insertions(+), 24 deletions(-) + +--- a/drivers/net/dsa/mt7530.c ++++ b/drivers/net/dsa/mt7530.c +@@ -2950,26 +2950,56 @@ static const struct regmap_bus mt7531_re + .reg_update_bits = mt7530_regmap_update_bits, + }; + +-#define MT7531_PCS_REGMAP_CONFIG(_name, _reg_base) \ +- { \ +- .name = _name, \ +- .reg_bits = 16, \ +- .val_bits = 32, \ +- .reg_stride = 4, \ +- .reg_base = _reg_base, \ +- .max_register = 0x17c, \ ++static int ++mt7531_create_sgmii(struct mt7530_priv *priv) ++{ ++ struct regmap_config *mt7531_pcs_config[2]; ++ struct phylink_pcs *pcs; ++ struct regmap *regmap; ++ int i, ret = 0; ++ ++ for (i = 0; i < 2; i++) { ++ mt7531_pcs_config[i] = devm_kzalloc(priv->dev, ++ sizeof(struct regmap_config), ++ GFP_KERNEL); ++ if (!mt7531_pcs_config[i]) { ++ ret = -ENOMEM; ++ break; ++ } ++ ++ mt7531_pcs_config[i]->name = i ? "port6" : "port5"; ++ mt7531_pcs_config[i]->reg_bits = 16; ++ mt7531_pcs_config[i]->val_bits = 32; ++ mt7531_pcs_config[i]->reg_stride = 4; ++ mt7531_pcs_config[i]->reg_base = MT7531_SGMII_REG_BASE(5 + i); ++ mt7531_pcs_config[i]->max_register = 0x17c; ++ ++ regmap = devm_regmap_init(priv->dev, ++ &mt7531_regmap_bus, priv, ++ mt7531_pcs_config[i]); ++ if (IS_ERR(regmap)) { ++ ret = PTR_ERR(regmap); ++ break; ++ } ++ pcs = mtk_pcs_lynxi_create(priv->dev, regmap, ++ MT7531_PHYA_CTRL_SIGNAL3, 0); ++ if (!pcs) { ++ ret = -ENXIO; ++ break; ++ } ++ priv->ports[5 + i].sgmii_pcs = pcs; + } + +-static const struct regmap_config mt7531_pcs_config[] = { +- MT7531_PCS_REGMAP_CONFIG("port5", MT7531_SGMII_REG_BASE(5)), +- MT7531_PCS_REGMAP_CONFIG("port6", MT7531_SGMII_REG_BASE(6)), +-}; ++ if (ret && i) ++ mtk_pcs_lynxi_destroy(priv->ports[5].sgmii_pcs); ++ ++ return ret; ++} + + static int + mt753x_setup(struct dsa_switch *ds) + { + struct mt7530_priv *priv = ds->priv; +- struct regmap *regmap; + int i, ret; + + /* Initialise the PCS devices */ +@@ -2991,15 +3021,11 @@ mt753x_setup(struct dsa_switch *ds) + if (ret && priv->irq) + mt7530_free_irq_common(priv); + +- if (priv->id == ID_MT7531) +- for (i = 0; i < 2; i++) { +- regmap = devm_regmap_init(ds->dev, +- &mt7531_regmap_bus, priv, +- &mt7531_pcs_config[i]); +- priv->ports[5 + i].sgmii_pcs = +- mtk_pcs_lynxi_create(ds->dev, regmap, +- MT7531_PHYA_CTRL_SIGNAL3, 0); +- } ++ if (priv->id == ID_MT7531) { ++ ret = mt7531_create_sgmii(priv); ++ if (ret && priv->irq) ++ mt7530_free_irq_common(priv); ++ } + + return ret; + } diff --git a/target/linux/generic/backport-6.1/790-v6.4-0003-net-dsa-mt7530-use-unlocked-regmap-accessors.patch b/target/linux/generic/backport-6.1/790-v6.4-0003-net-dsa-mt7530-use-unlocked-regmap-accessors.patch new file mode 100644 index 0000000000..77ac3f3f26 --- /dev/null +++ b/target/linux/generic/backport-6.1/790-v6.4-0003-net-dsa-mt7530-use-unlocked-regmap-accessors.patch @@ -0,0 +1,74 @@ +From 33396408776385f3d2f6069646169a6b5b28e3b3 Mon Sep 17 00:00:00 2001 +From: Daniel Golle +Date: Mon, 3 Apr 2023 02:17:40 +0100 +Subject: [PATCH 03/13] net: dsa: mt7530: use unlocked regmap accessors + +Instead of wrapping the locked register accessor functions, use the +unlocked variants and add locking wrapper functions to let regmap +handle the locking. + +This is a preparation towards being able to always use regmap to +access switch registers instead of open-coded accessor functions. + +Signed-off-by: Daniel Golle +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/mt7530.c | 23 ++++++++++++++--------- + 1 file changed, 14 insertions(+), 9 deletions(-) + +--- a/drivers/net/dsa/mt7530.c ++++ b/drivers/net/dsa/mt7530.c +@@ -2923,7 +2923,7 @@ static int mt7530_regmap_read(void *cont + { + struct mt7530_priv *priv = context; + +- *val = mt7530_read(priv, reg); ++ *val = mt7530_mii_read(priv, reg); + return 0; + }; + +@@ -2931,23 +2931,25 @@ static int mt7530_regmap_write(void *con + { + struct mt7530_priv *priv = context; + +- mt7530_write(priv, reg, val); ++ mt7530_mii_write(priv, reg, val); + return 0; + }; + +-static int mt7530_regmap_update_bits(void *context, unsigned int reg, +- unsigned int mask, unsigned int val) ++static void ++mt7530_mdio_regmap_lock(void *mdio_lock) + { +- struct mt7530_priv *priv = context; ++ mutex_lock_nested(mdio_lock, MDIO_MUTEX_NESTED); ++} + +- mt7530_rmw(priv, reg, mask, val); +- return 0; +-}; ++static void ++mt7530_mdio_regmap_unlock(void *mdio_lock) ++{ ++ mutex_unlock(mdio_lock); ++} + + static const struct regmap_bus mt7531_regmap_bus = { + .reg_write = mt7530_regmap_write, + .reg_read = mt7530_regmap_read, +- .reg_update_bits = mt7530_regmap_update_bits, + }; + + static int +@@ -2973,6 +2975,9 @@ mt7531_create_sgmii(struct mt7530_priv * + mt7531_pcs_config[i]->reg_stride = 4; + mt7531_pcs_config[i]->reg_base = MT7531_SGMII_REG_BASE(5 + i); + mt7531_pcs_config[i]->max_register = 0x17c; ++ mt7531_pcs_config[i]->lock = mt7530_mdio_regmap_lock; ++ mt7531_pcs_config[i]->unlock = mt7530_mdio_regmap_unlock; ++ mt7531_pcs_config[i]->lock_arg = &priv->bus->mdio_lock; + + regmap = devm_regmap_init(priv->dev, + &mt7531_regmap_bus, priv, diff --git a/target/linux/generic/backport-6.1/790-v6.4-0004-net-dsa-mt7530-use-regmap-to-access-switch-register-.patch b/target/linux/generic/backport-6.1/790-v6.4-0004-net-dsa-mt7530-use-regmap-to-access-switch-register-.patch new file mode 100644 index 0000000000..6e3e8b09b9 --- /dev/null +++ b/target/linux/generic/backport-6.1/790-v6.4-0004-net-dsa-mt7530-use-regmap-to-access-switch-register-.patch @@ -0,0 +1,224 @@ +From 743cba4345cb366248f9d375c6a9e50243dc0677 Mon Sep 17 00:00:00 2001 +From: Daniel Golle +Date: Mon, 3 Apr 2023 02:17:52 +0100 +Subject: [PATCH 04/13] net: dsa: mt7530: use regmap to access switch register + space + +Use regmap API to access the switch register space. + +Signed-off-by: Daniel Golle +Signed-off-by: David S. Miller +--- + drivers/net/dsa/mt7530.c | 99 ++++++++++++++++++++++++---------------- + drivers/net/dsa/mt7530.h | 2 + + 2 files changed, 62 insertions(+), 39 deletions(-) + +--- a/drivers/net/dsa/mt7530.c ++++ b/drivers/net/dsa/mt7530.c +@@ -183,9 +183,9 @@ core_clear(struct mt7530_priv *priv, u32 + } + + static int +-mt7530_mii_write(struct mt7530_priv *priv, u32 reg, u32 val) ++mt7530_regmap_write(void *context, unsigned int reg, unsigned int val) + { +- struct mii_bus *bus = priv->bus; ++ struct mii_bus *bus = context; + u16 page, r, lo, hi; + int ret; + +@@ -197,24 +197,34 @@ mt7530_mii_write(struct mt7530_priv *pri + /* MT7530 uses 31 as the pseudo port */ + ret = bus->write(bus, 0x1f, 0x1f, page); + if (ret < 0) +- goto err; ++ return ret; + + ret = bus->write(bus, 0x1f, r, lo); + if (ret < 0) +- goto err; ++ return ret; + + ret = bus->write(bus, 0x1f, 0x10, hi); +-err: ++ return ret; ++} ++ ++static int ++mt7530_mii_write(struct mt7530_priv *priv, u32 reg, u32 val) ++{ ++ int ret; ++ ++ ret = regmap_write(priv->regmap, reg, val); ++ + if (ret < 0) +- dev_err(&bus->dev, ++ dev_err(priv->dev, + "failed to write mt7530 register\n"); ++ + return ret; + } + +-static u32 +-mt7530_mii_read(struct mt7530_priv *priv, u32 reg) ++static int ++mt7530_regmap_read(void *context, unsigned int reg, unsigned int *val) + { +- struct mii_bus *bus = priv->bus; ++ struct mii_bus *bus = context; + u16 page, r, lo, hi; + int ret; + +@@ -223,17 +233,32 @@ mt7530_mii_read(struct mt7530_priv *priv + + /* MT7530 uses 31 as the pseudo port */ + ret = bus->write(bus, 0x1f, 0x1f, page); +- if (ret < 0) { ++ if (ret < 0) ++ return ret; ++ ++ lo = bus->read(bus, 0x1f, r); ++ hi = bus->read(bus, 0x1f, 0x10); ++ ++ *val = (hi << 16) | (lo & 0xffff); ++ ++ return 0; ++} ++ ++static u32 ++mt7530_mii_read(struct mt7530_priv *priv, u32 reg) ++{ ++ int ret; ++ u32 val; ++ ++ ret = regmap_read(priv->regmap, reg, &val); ++ if (ret) { + WARN_ON_ONCE(1); +- dev_err(&bus->dev, ++ dev_err(priv->dev, + "failed to read mt7530 register\n"); + return 0; + } + +- lo = bus->read(bus, 0x1f, r); +- hi = bus->read(bus, 0x1f, 0x10); +- +- return (hi << 16) | (lo & 0xffff); ++ return val; + } + + static void +@@ -283,14 +308,10 @@ mt7530_rmw(struct mt7530_priv *priv, u32 + u32 mask, u32 set) + { + struct mii_bus *bus = priv->bus; +- u32 val; + + mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); + +- val = mt7530_mii_read(priv, reg); +- val &= ~mask; +- val |= set; +- mt7530_mii_write(priv, reg, val); ++ regmap_update_bits(priv->regmap, reg, mask, set); + + mutex_unlock(&bus->mdio_lock); + } +@@ -298,7 +319,7 @@ mt7530_rmw(struct mt7530_priv *priv, u32 + static void + mt7530_set(struct mt7530_priv *priv, u32 reg, u32 val) + { +- mt7530_rmw(priv, reg, 0, val); ++ mt7530_rmw(priv, reg, val, val); + } + + static void +@@ -2919,22 +2940,6 @@ static const struct phylink_pcs_ops mt75 + .pcs_an_restart = mt7530_pcs_an_restart, + }; + +-static int mt7530_regmap_read(void *context, unsigned int reg, unsigned int *val) +-{ +- struct mt7530_priv *priv = context; +- +- *val = mt7530_mii_read(priv, reg); +- return 0; +-}; +- +-static int mt7530_regmap_write(void *context, unsigned int reg, unsigned int val) +-{ +- struct mt7530_priv *priv = context; +- +- mt7530_mii_write(priv, reg, val); +- return 0; +-}; +- + static void + mt7530_mdio_regmap_lock(void *mdio_lock) + { +@@ -2947,7 +2952,7 @@ mt7530_mdio_regmap_unlock(void *mdio_loc + mutex_unlock(mdio_lock); + } + +-static const struct regmap_bus mt7531_regmap_bus = { ++static const struct regmap_bus mt7530_regmap_bus = { + .reg_write = mt7530_regmap_write, + .reg_read = mt7530_regmap_read, + }; +@@ -2980,7 +2985,7 @@ mt7531_create_sgmii(struct mt7530_priv * + mt7531_pcs_config[i]->lock_arg = &priv->bus->mdio_lock; + + regmap = devm_regmap_init(priv->dev, +- &mt7531_regmap_bus, priv, ++ &mt7530_regmap_bus, priv->bus, + mt7531_pcs_config[i]); + if (IS_ERR(regmap)) { + ret = PTR_ERR(regmap); +@@ -3145,6 +3150,7 @@ MODULE_DEVICE_TABLE(of, mt7530_of_match) + static int + mt7530_probe(struct mdio_device *mdiodev) + { ++ static struct regmap_config *regmap_config; + struct mt7530_priv *priv; + struct device_node *dn; + +@@ -3224,6 +3230,21 @@ mt7530_probe(struct mdio_device *mdiodev + mutex_init(&priv->reg_mutex); + dev_set_drvdata(&mdiodev->dev, priv); + ++ regmap_config = devm_kzalloc(&mdiodev->dev, sizeof(*regmap_config), ++ GFP_KERNEL); ++ if (!regmap_config) ++ return -ENOMEM; ++ ++ regmap_config->reg_bits = 16; ++ regmap_config->val_bits = 32; ++ regmap_config->reg_stride = 4; ++ regmap_config->max_register = MT7530_CREV; ++ regmap_config->disable_locking = true; ++ priv->regmap = devm_regmap_init(priv->dev, &mt7530_regmap_bus, ++ priv->bus, regmap_config); ++ if (IS_ERR(priv->regmap)) ++ return PTR_ERR(priv->regmap); ++ + return dsa_register_switch(priv->ds); + } + +--- a/drivers/net/dsa/mt7530.h ++++ b/drivers/net/dsa/mt7530.h +@@ -747,6 +747,7 @@ struct mt753x_info { + * @dev: The device pointer + * @ds: The pointer to the dsa core structure + * @bus: The bus used for the device and built-in PHY ++ * @regmap: The regmap instance representing all switch registers + * @rstc: The pointer to reset control used by MCM + * @core_pwr: The power supplied into the core + * @io_pwr: The power supplied into the I/O +@@ -767,6 +768,7 @@ struct mt7530_priv { + struct device *dev; + struct dsa_switch *ds; + struct mii_bus *bus; ++ struct regmap *regmap; + struct reset_control *rstc; + struct regulator *core_pwr; + struct regulator *io_pwr; diff --git a/target/linux/generic/backport-6.1/790-v6.4-0005-net-dsa-mt7530-move-SGMII-PCS-creation-to-mt7530_pro.patch b/target/linux/generic/backport-6.1/790-v6.4-0005-net-dsa-mt7530-move-SGMII-PCS-creation-to-mt7530_pro.patch new file mode 100644 index 0000000000..a02702fd68 --- /dev/null +++ b/target/linux/generic/backport-6.1/790-v6.4-0005-net-dsa-mt7530-move-SGMII-PCS-creation-to-mt7530_pro.patch @@ -0,0 +1,54 @@ +From f3cf1d06e2aef644b426c23b4bb570780b1f8d47 Mon Sep 17 00:00:00 2001 +From: Daniel Golle +Date: Mon, 3 Apr 2023 02:18:04 +0100 +Subject: [PATCH 05/13] net: dsa: mt7530: move SGMII PCS creation to + mt7530_probe function + +Move creating the SGMII PCS from mt753x_setup() to the more appropriate +mt7530_probe() function. +This is done also in preparation of moving all functions related to +MDIO-connected MT753x switches to a separate module. + +Signed-off-by: Daniel Golle +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/mt7530.c | 13 +++++++------ + 1 file changed, 7 insertions(+), 6 deletions(-) + +--- a/drivers/net/dsa/mt7530.c ++++ b/drivers/net/dsa/mt7530.c +@@ -3031,12 +3031,6 @@ mt753x_setup(struct dsa_switch *ds) + if (ret && priv->irq) + mt7530_free_irq_common(priv); + +- if (priv->id == ID_MT7531) { +- ret = mt7531_create_sgmii(priv); +- if (ret && priv->irq) +- mt7530_free_irq_common(priv); +- } +- + return ret; + } + +@@ -3153,6 +3147,7 @@ mt7530_probe(struct mdio_device *mdiodev + static struct regmap_config *regmap_config; + struct mt7530_priv *priv; + struct device_node *dn; ++ int ret; + + dn = mdiodev->dev.of_node; + +@@ -3245,6 +3240,12 @@ mt7530_probe(struct mdio_device *mdiodev + if (IS_ERR(priv->regmap)) + return PTR_ERR(priv->regmap); + ++ if (priv->id == ID_MT7531) { ++ ret = mt7531_create_sgmii(priv); ++ if (ret) ++ return ret; ++ } ++ + return dsa_register_switch(priv->ds); + } + diff --git a/target/linux/generic/backport-6.1/790-v6.4-0006-net-dsa-mt7530-introduce-mutex-helpers.patch b/target/linux/generic/backport-6.1/790-v6.4-0006-net-dsa-mt7530-introduce-mutex-helpers.patch new file mode 100644 index 0000000000..98122caf09 --- /dev/null +++ b/target/linux/generic/backport-6.1/790-v6.4-0006-net-dsa-mt7530-introduce-mutex-helpers.patch @@ -0,0 +1,273 @@ +From e4729ae7c095c0c87794bff47ea43e35d69de986 Mon Sep 17 00:00:00 2001 +From: Daniel Golle +Date: Mon, 3 Apr 2023 02:18:16 +0100 +Subject: [PATCH 06/13] net: dsa: mt7530: introduce mutex helpers + +As the MDIO bus lock only needs to be involved if actually operating +on an MDIO-connected switch we will need to skip locking for built-in +switches which are accessed via MMIO. +Create helper functions which simplify that upcoming change. + +Signed-off-by: Daniel Golle +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/mt7530.c | 73 ++++++++++++++++++++-------------------- + 1 file changed, 36 insertions(+), 37 deletions(-) + +--- a/drivers/net/dsa/mt7530.c ++++ b/drivers/net/dsa/mt7530.c +@@ -143,31 +143,40 @@ err: + } + + static void +-core_write(struct mt7530_priv *priv, u32 reg, u32 val) ++mt7530_mutex_lock(struct mt7530_priv *priv) + { +- struct mii_bus *bus = priv->bus; ++ mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); ++} + +- mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); ++static void ++mt7530_mutex_unlock(struct mt7530_priv *priv) ++{ ++ mutex_unlock(&priv->bus->mdio_lock); ++} ++ ++static void ++core_write(struct mt7530_priv *priv, u32 reg, u32 val) ++{ ++ mt7530_mutex_lock(priv); + + core_write_mmd_indirect(priv, reg, MDIO_MMD_VEND2, val); + +- mutex_unlock(&bus->mdio_lock); ++ mt7530_mutex_unlock(priv); + } + + static void + core_rmw(struct mt7530_priv *priv, u32 reg, u32 mask, u32 set) + { +- struct mii_bus *bus = priv->bus; + u32 val; + +- mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); ++ mt7530_mutex_lock(priv); + + val = core_read_mmd_indirect(priv, reg, MDIO_MMD_VEND2); + val &= ~mask; + val |= set; + core_write_mmd_indirect(priv, reg, MDIO_MMD_VEND2, val); + +- mutex_unlock(&bus->mdio_lock); ++ mt7530_mutex_unlock(priv); + } + + static void +@@ -264,13 +273,11 @@ mt7530_mii_read(struct mt7530_priv *priv + static void + mt7530_write(struct mt7530_priv *priv, u32 reg, u32 val) + { +- struct mii_bus *bus = priv->bus; +- +- mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); ++ mt7530_mutex_lock(priv); + + mt7530_mii_write(priv, reg, val); + +- mutex_unlock(&bus->mdio_lock); ++ mt7530_mutex_unlock(priv); + } + + static u32 +@@ -282,14 +289,13 @@ _mt7530_unlocked_read(struct mt7530_dumm + static u32 + _mt7530_read(struct mt7530_dummy_poll *p) + { +- struct mii_bus *bus = p->priv->bus; + u32 val; + +- mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); ++ mt7530_mutex_lock(p->priv); + + val = mt7530_mii_read(p->priv, p->reg); + +- mutex_unlock(&bus->mdio_lock); ++ mt7530_mutex_unlock(p->priv); + + return val; + } +@@ -307,13 +313,11 @@ static void + mt7530_rmw(struct mt7530_priv *priv, u32 reg, + u32 mask, u32 set) + { +- struct mii_bus *bus = priv->bus; +- +- mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); ++ mt7530_mutex_lock(priv); + + regmap_update_bits(priv->regmap, reg, mask, set); + +- mutex_unlock(&bus->mdio_lock); ++ mt7530_mutex_unlock(priv); + } + + static void +@@ -645,14 +649,13 @@ static int + mt7531_ind_c45_phy_read(struct mt7530_priv *priv, int port, int devad, + int regnum) + { +- struct mii_bus *bus = priv->bus; + struct mt7530_dummy_poll p; + u32 reg, val; + int ret; + + INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC); + +- mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); ++ mt7530_mutex_lock(priv); + + ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val, + !(val & MT7531_PHY_ACS_ST), 20, 100000); +@@ -685,7 +688,7 @@ mt7531_ind_c45_phy_read(struct mt7530_pr + + ret = val & MT7531_MDIO_RW_DATA_MASK; + out: +- mutex_unlock(&bus->mdio_lock); ++ mt7530_mutex_unlock(priv); + + return ret; + } +@@ -694,14 +697,13 @@ static int + mt7531_ind_c45_phy_write(struct mt7530_priv *priv, int port, int devad, + int regnum, u32 data) + { +- struct mii_bus *bus = priv->bus; + struct mt7530_dummy_poll p; + u32 val, reg; + int ret; + + INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC); + +- mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); ++ mt7530_mutex_lock(priv); + + ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val, + !(val & MT7531_PHY_ACS_ST), 20, 100000); +@@ -733,7 +735,7 @@ mt7531_ind_c45_phy_write(struct mt7530_p + } + + out: +- mutex_unlock(&bus->mdio_lock); ++ mt7530_mutex_unlock(priv); + + return ret; + } +@@ -741,14 +743,13 @@ out: + static int + mt7531_ind_c22_phy_read(struct mt7530_priv *priv, int port, int regnum) + { +- struct mii_bus *bus = priv->bus; + struct mt7530_dummy_poll p; + int ret; + u32 val; + + INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC); + +- mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); ++ mt7530_mutex_lock(priv); + + ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val, + !(val & MT7531_PHY_ACS_ST), 20, 100000); +@@ -771,7 +772,7 @@ mt7531_ind_c22_phy_read(struct mt7530_pr + + ret = val & MT7531_MDIO_RW_DATA_MASK; + out: +- mutex_unlock(&bus->mdio_lock); ++ mt7530_mutex_unlock(priv); + + return ret; + } +@@ -780,14 +781,13 @@ static int + mt7531_ind_c22_phy_write(struct mt7530_priv *priv, int port, int regnum, + u16 data) + { +- struct mii_bus *bus = priv->bus; + struct mt7530_dummy_poll p; + int ret; + u32 reg; + + INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC); + +- mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); ++ mt7530_mutex_lock(priv); + + ret = readx_poll_timeout(_mt7530_unlocked_read, &p, reg, + !(reg & MT7531_PHY_ACS_ST), 20, 100000); +@@ -809,7 +809,7 @@ mt7531_ind_c22_phy_write(struct mt7530_p + } + + out: +- mutex_unlock(&bus->mdio_lock); ++ mt7530_mutex_unlock(priv); + + return ret; + } +@@ -1109,7 +1109,6 @@ static int + mt7530_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu) + { + struct mt7530_priv *priv = ds->priv; +- struct mii_bus *bus = priv->bus; + int length; + u32 val; + +@@ -1120,7 +1119,7 @@ mt7530_port_change_mtu(struct dsa_switch + if (!dsa_is_cpu_port(ds, port)) + return 0; + +- mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); ++ mt7530_mutex_lock(priv); + + val = mt7530_mii_read(priv, MT7530_GMACCR); + val &= ~MAX_RX_PKT_LEN_MASK; +@@ -1141,7 +1140,7 @@ mt7530_port_change_mtu(struct dsa_switch + + mt7530_mii_write(priv, MT7530_GMACCR, val); + +- mutex_unlock(&bus->mdio_lock); ++ mt7530_mutex_unlock(priv); + + return 0; + } +@@ -1942,10 +1941,10 @@ mt7530_irq_thread_fn(int irq, void *dev_ + u32 val; + int p; + +- mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); ++ mt7530_mutex_lock(priv); + val = mt7530_mii_read(priv, MT7530_SYS_INT_STS); + mt7530_mii_write(priv, MT7530_SYS_INT_STS, val); +- mutex_unlock(&priv->bus->mdio_lock); ++ mt7530_mutex_unlock(priv); + + for (p = 0; p < MT7530_NUM_PHYS; p++) { + if (BIT(p) & val) { +@@ -1981,7 +1980,7 @@ mt7530_irq_bus_lock(struct irq_data *d) + { + struct mt7530_priv *priv = irq_data_get_irq_chip_data(d); + +- mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); ++ mt7530_mutex_lock(priv); + } + + static void +@@ -1990,7 +1989,7 @@ mt7530_irq_bus_sync_unlock(struct irq_da + struct mt7530_priv *priv = irq_data_get_irq_chip_data(d); + + mt7530_mii_write(priv, MT7530_SYS_INT_EN, priv->irq_enable); +- mutex_unlock(&priv->bus->mdio_lock); ++ mt7530_mutex_unlock(priv); + } + + static struct irq_chip mt7530_irq_chip = { diff --git a/target/linux/generic/backport-6.1/790-v6.4-0007-net-dsa-mt7530-move-p5_intf_modes-function-to-mt7530.patch b/target/linux/generic/backport-6.1/790-v6.4-0007-net-dsa-mt7530-move-p5_intf_modes-function-to-mt7530.patch new file mode 100644 index 0000000000..5065d73523 --- /dev/null +++ b/target/linux/generic/backport-6.1/790-v6.4-0007-net-dsa-mt7530-move-p5_intf_modes-function-to-mt7530.patch @@ -0,0 +1,75 @@ +From 0d7ae94a0c581f86939bebec0b6ccd66e640d1d8 Mon Sep 17 00:00:00 2001 +From: Daniel Golle +Date: Mon, 3 Apr 2023 02:18:28 +0100 +Subject: [PATCH 07/13] net: dsa: mt7530: move p5_intf_modes() function to + mt7530.c + +In preparation of splitting mt7530.c into a driver for MDIO-connected +as well as MDIO-accessed built-in switches on one hand and MMIO-accessed +built-in switches move the p5_inft_modes() function from mt7530.h to +mt7530.c. The function is only needed there and will trigger a compiler +warning about a defined but unused function otherwise when including +mt7530.h in the to-be-introduced bus-specific drivers. + +Signed-off-by: Daniel Golle +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/mt7530.c | 18 ++++++++++++++++++ + drivers/net/dsa/mt7530.h | 18 ------------------ + 2 files changed, 18 insertions(+), 18 deletions(-) + +--- a/drivers/net/dsa/mt7530.c ++++ b/drivers/net/dsa/mt7530.c +@@ -950,6 +950,24 @@ mt7530_set_ageing_time(struct dsa_switch + return 0; + } + ++static const char *p5_intf_modes(unsigned int p5_interface) ++{ ++ switch (p5_interface) { ++ case P5_DISABLED: ++ return "DISABLED"; ++ case P5_INTF_SEL_PHY_P0: ++ return "PHY P0"; ++ case P5_INTF_SEL_PHY_P4: ++ return "PHY P4"; ++ case P5_INTF_SEL_GMAC5: ++ return "GMAC5"; ++ case P5_INTF_SEL_GMAC5_SGMII: ++ return "GMAC5_SGMII"; ++ default: ++ return "unknown"; ++ } ++} ++ + static void mt7530_setup_port5(struct dsa_switch *ds, phy_interface_t interface) + { + struct mt7530_priv *priv = ds->priv; +--- a/drivers/net/dsa/mt7530.h ++++ b/drivers/net/dsa/mt7530.h +@@ -682,24 +682,6 @@ enum p5_interface_select { + P5_INTF_SEL_GMAC5_SGMII, + }; + +-static const char *p5_intf_modes(unsigned int p5_interface) +-{ +- switch (p5_interface) { +- case P5_DISABLED: +- return "DISABLED"; +- case P5_INTF_SEL_PHY_P0: +- return "PHY P0"; +- case P5_INTF_SEL_PHY_P4: +- return "PHY P4"; +- case P5_INTF_SEL_GMAC5: +- return "GMAC5"; +- case P5_INTF_SEL_GMAC5_SGMII: +- return "GMAC5_SGMII"; +- default: +- return "unknown"; +- } +-} +- + struct mt7530_priv; + + struct mt753x_pcs { diff --git a/target/linux/generic/backport-6.1/790-v6.4-0008-net-dsa-mt7530-introduce-mt7530_probe_common-helper-.patch b/target/linux/generic/backport-6.1/790-v6.4-0008-net-dsa-mt7530-introduce-mt7530_probe_common-helper-.patch new file mode 100644 index 0000000000..761aa1d979 --- /dev/null +++ b/target/linux/generic/backport-6.1/790-v6.4-0008-net-dsa-mt7530-introduce-mt7530_probe_common-helper-.patch @@ -0,0 +1,155 @@ +From 4d632005c90e253c000d0db73b7cdb9d8dc2e2dd Mon Sep 17 00:00:00 2001 +From: Daniel Golle +Date: Mon, 3 Apr 2023 02:18:39 +0100 +Subject: [PATCH 08/13] net: dsa: mt7530: introduce mt7530_probe_common helper + function + +Move commonly used parts from mt7530_probe into new mt7530_probe_common +helper function which will be used by both, mt7530_probe and the +to-be-introduced mt7988_probe. + +Signed-off-by: Daniel Golle +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/mt7530.c | 98 ++++++++++++++++++++++------------------ + 1 file changed, 54 insertions(+), 44 deletions(-) + +--- a/drivers/net/dsa/mt7530.c ++++ b/drivers/net/dsa/mt7530.c +@@ -3159,44 +3159,21 @@ static const struct of_device_id mt7530_ + MODULE_DEVICE_TABLE(of, mt7530_of_match); + + static int +-mt7530_probe(struct mdio_device *mdiodev) ++mt7530_probe_common(struct mt7530_priv *priv) + { +- static struct regmap_config *regmap_config; +- struct mt7530_priv *priv; +- struct device_node *dn; +- int ret; ++ struct device *dev = priv->dev; + +- dn = mdiodev->dev.of_node; +- +- priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL); +- if (!priv) +- return -ENOMEM; +- +- priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL); ++ priv->ds = devm_kzalloc(dev, sizeof(*priv->ds), GFP_KERNEL); + if (!priv->ds) + return -ENOMEM; + +- priv->ds->dev = &mdiodev->dev; ++ priv->ds->dev = dev; + priv->ds->num_ports = MT7530_NUM_PORTS; + +- /* Use medatek,mcm property to distinguish hardware type that would +- * casues a little bit differences on power-on sequence. +- */ +- priv->mcm = of_property_read_bool(dn, "mediatek,mcm"); +- if (priv->mcm) { +- dev_info(&mdiodev->dev, "MT7530 adapts as multi-chip module\n"); +- +- priv->rstc = devm_reset_control_get(&mdiodev->dev, "mcm"); +- if (IS_ERR(priv->rstc)) { +- dev_err(&mdiodev->dev, "Couldn't get our reset line\n"); +- return PTR_ERR(priv->rstc); +- } +- } +- + /* Get the hardware identifier from the devicetree node. + * We will need it for some of the clock and regulator setup. + */ +- priv->info = of_device_get_match_data(&mdiodev->dev); ++ priv->info = of_device_get_match_data(dev); + if (!priv->info) + return -EINVAL; + +@@ -3210,23 +3187,53 @@ mt7530_probe(struct mdio_device *mdiodev + return -EINVAL; + + priv->id = priv->info->id; ++ priv->dev = dev; ++ priv->ds->priv = priv; ++ priv->ds->ops = &mt7530_switch_ops; ++ mutex_init(&priv->reg_mutex); ++ dev_set_drvdata(dev, priv); + +- if (priv->id == ID_MT7530) { +- priv->core_pwr = devm_regulator_get(&mdiodev->dev, "core"); +- if (IS_ERR(priv->core_pwr)) +- return PTR_ERR(priv->core_pwr); ++ return 0; ++} + +- priv->io_pwr = devm_regulator_get(&mdiodev->dev, "io"); +- if (IS_ERR(priv->io_pwr)) +- return PTR_ERR(priv->io_pwr); +- } ++static int ++mt7530_probe(struct mdio_device *mdiodev) ++{ ++ static struct regmap_config *regmap_config; ++ struct mt7530_priv *priv; ++ struct device_node *dn; ++ int ret; ++ ++ dn = mdiodev->dev.of_node; ++ ++ priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL); ++ if (!priv) ++ return -ENOMEM; + +- /* Not MCM that indicates switch works as the remote standalone ++ priv->bus = mdiodev->bus; ++ priv->dev = &mdiodev->dev; ++ ++ ret = mt7530_probe_common(priv); ++ if (ret) ++ return ret; ++ ++ /* Use medatek,mcm property to distinguish hardware type that would ++ * cause a little bit differences on power-on sequence. ++ * Not MCM that indicates switch works as the remote standalone + * integrated circuit so the GPIO pin would be used to complete + * the reset, otherwise memory-mapped register accessing used + * through syscon provides in the case of MCM. + */ +- if (!priv->mcm) { ++ priv->mcm = of_property_read_bool(dn, "mediatek,mcm"); ++ if (priv->mcm) { ++ dev_info(&mdiodev->dev, "MT7530 adapts as multi-chip module\n"); ++ ++ priv->rstc = devm_reset_control_get(&mdiodev->dev, "mcm"); ++ if (IS_ERR(priv->rstc)) { ++ dev_err(&mdiodev->dev, "Couldn't get our reset line\n"); ++ return PTR_ERR(priv->rstc); ++ } ++ } else { + priv->reset = devm_gpiod_get_optional(&mdiodev->dev, "reset", + GPIOD_OUT_LOW); + if (IS_ERR(priv->reset)) { +@@ -3235,12 +3242,15 @@ mt7530_probe(struct mdio_device *mdiodev + } + } + +- priv->bus = mdiodev->bus; +- priv->dev = &mdiodev->dev; +- priv->ds->priv = priv; +- priv->ds->ops = &mt7530_switch_ops; +- mutex_init(&priv->reg_mutex); +- dev_set_drvdata(&mdiodev->dev, priv); ++ if (priv->id == ID_MT7530) { ++ priv->core_pwr = devm_regulator_get(&mdiodev->dev, "core"); ++ if (IS_ERR(priv->core_pwr)) ++ return PTR_ERR(priv->core_pwr); ++ ++ priv->io_pwr = devm_regulator_get(&mdiodev->dev, "io"); ++ if (IS_ERR(priv->io_pwr)) ++ return PTR_ERR(priv->io_pwr); ++ } + + regmap_config = devm_kzalloc(&mdiodev->dev, sizeof(*regmap_config), + GFP_KERNEL); diff --git a/target/linux/generic/backport-6.1/790-v6.4-0009-net-dsa-mt7530-introduce-mt7530_remove_common-helper.patch b/target/linux/generic/backport-6.1/790-v6.4-0009-net-dsa-mt7530-introduce-mt7530_remove_common-helper.patch new file mode 100644 index 0000000000..d3c2a7e2c9 --- /dev/null +++ b/target/linux/generic/backport-6.1/790-v6.4-0009-net-dsa-mt7530-introduce-mt7530_remove_common-helper.patch @@ -0,0 +1,54 @@ +From 69b838d2629e6b82bcd9e0ab3c1c03f46e5e01d3 Mon Sep 17 00:00:00 2001 +From: Daniel Golle +Date: Mon, 3 Apr 2023 02:18:50 +0100 +Subject: [PATCH 09/13] net: dsa: mt7530: introduce mt7530_remove_common helper + function + +Move commonly used parts from mt7530_remove into new +mt7530_remove_common helper function which will be used by both, +mt7530_remove and the to-be-introduced mt7988_remove. + +Signed-off-by: Daniel Golle +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/mt7530.c | 18 ++++++++++++------ + 1 file changed, 12 insertions(+), 6 deletions(-) + +--- a/drivers/net/dsa/mt7530.c ++++ b/drivers/net/dsa/mt7530.c +@@ -3277,6 +3277,17 @@ mt7530_probe(struct mdio_device *mdiodev + } + + static void ++mt7530_remove_common(struct mt7530_priv *priv) ++{ ++ if (priv->irq) ++ mt7530_free_irq(priv); ++ ++ dsa_unregister_switch(priv->ds); ++ ++ mutex_destroy(&priv->reg_mutex); ++} ++ ++static void + mt7530_remove(struct mdio_device *mdiodev) + { + struct mt7530_priv *priv = dev_get_drvdata(&mdiodev->dev); +@@ -3295,15 +3306,10 @@ mt7530_remove(struct mdio_device *mdiode + dev_err(priv->dev, "Failed to disable io pwr: %d\n", + ret); + +- if (priv->irq) +- mt7530_free_irq(priv); +- +- dsa_unregister_switch(priv->ds); ++ mt7530_remove_common(priv); + + for (i = 0; i < 2; ++i) + mtk_pcs_lynxi_destroy(priv->ports[5 + i].sgmii_pcs); +- +- mutex_destroy(&priv->reg_mutex); + } + + static void mt7530_shutdown(struct mdio_device *mdiodev) diff --git a/target/linux/generic/backport-6.1/790-v6.4-0010-net-dsa-mt7530-introduce-separate-MDIO-driver.patch b/target/linux/generic/backport-6.1/790-v6.4-0010-net-dsa-mt7530-introduce-separate-MDIO-driver.patch new file mode 100644 index 0000000000..55378ca016 --- /dev/null +++ b/target/linux/generic/backport-6.1/790-v6.4-0010-net-dsa-mt7530-introduce-separate-MDIO-driver.patch @@ -0,0 +1,691 @@ +From 8eceed6dbd74067dbf4d8e39f14734f4d2f35176 Mon Sep 17 00:00:00 2001 +From: Daniel Golle +Date: Mon, 3 Apr 2023 02:19:13 +0100 +Subject: [PATCH 10/13] net: dsa: mt7530: introduce separate MDIO driver + +Split MT7530 switch driver into a common part and a part specific +for MDIO connected switches and multi-chip modules. +Move MDIO-specific functions to newly introduced mt7530-mdio.c while +keeping the common parts in mt7530.c. +Introduce new Kconfig symbol CONFIG_NET_DSA_MT7530_MDIO which is +implied by CONFIG_NET_DSA_MT7530. + +Signed-off-by: Daniel Golle +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + MAINTAINERS | 1 + + drivers/net/dsa/Kconfig | 16 +- + drivers/net/dsa/Makefile | 1 + + drivers/net/dsa/mt7530-mdio.c | 271 ++++++++++++++++++++++++++++++++++ + drivers/net/dsa/mt7530.c | 264 +-------------------------------- + drivers/net/dsa/mt7530.h | 6 + + 6 files changed, 301 insertions(+), 258 deletions(-) + create mode 100644 drivers/net/dsa/mt7530-mdio.c + +--- a/MAINTAINERS ++++ b/MAINTAINERS +@@ -13060,6 +13060,7 @@ M: Landen Chao + L: netdev@vger.kernel.org + S: Maintained ++F: drivers/net/dsa/mt7530-mdio.c + F: drivers/net/dsa/mt7530.* + F: net/dsa/tag_mtk.c + +--- a/drivers/net/dsa/Kconfig ++++ b/drivers/net/dsa/Kconfig +@@ -37,10 +37,22 @@ config NET_DSA_MT7530 + tristate "MediaTek MT753x and MT7621 Ethernet switch support" + select NET_DSA_TAG_MTK + select MEDIATEK_GE_PHY ++ imply NET_DSA_MT7530_MDIO ++ help ++ This enables support for the MediaTek MT7530 and MT7531 Ethernet ++ switch chips. Multi-chip module MT7530 in MT7621AT, MT7621DAT, ++ MT7621ST and MT7623AI SoCs, and built-in switch in MT7988 SoC are ++ supported as well. ++ ++config NET_DSA_MT7530_MDIO ++ tristate "MediaTek MT7530 MDIO interface driver" ++ depends on NET_DSA_MT7530 + select PCS_MTK_LYNXI + help +- This enables support for the MediaTek MT7530, MT7531, and MT7621 +- Ethernet switch chips. ++ This enables support for the MediaTek MT7530 and MT7531 switch ++ chips which are connected via MDIO, as well as multi-chip ++ module MT7530 which can be found in the MT7621AT, MT7621DAT, ++ MT7621ST and MT7623AI SoCs. + + config NET_DSA_MV88E6060 + tristate "Marvell 88E6060 ethernet switch chip support" +--- a/drivers/net/dsa/Makefile ++++ b/drivers/net/dsa/Makefile +@@ -7,6 +7,7 @@ obj-$(CONFIG_FIXED_PHY) += dsa_loop_bdi + endif + obj-$(CONFIG_NET_DSA_LANTIQ_GSWIP) += lantiq_gswip.o + obj-$(CONFIG_NET_DSA_MT7530) += mt7530.o ++obj-$(CONFIG_NET_DSA_MT7530_MDIO) += mt7530-mdio.o + obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e6060.o + obj-$(CONFIG_NET_DSA_RZN1_A5PSW) += rzn1_a5psw.o + obj-$(CONFIG_NET_DSA_SMSC_LAN9303) += lan9303-core.o +--- /dev/null ++++ b/drivers/net/dsa/mt7530-mdio.c +@@ -0,0 +1,271 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "mt7530.h" ++ ++static int ++mt7530_regmap_write(void *context, unsigned int reg, unsigned int val) ++{ ++ struct mii_bus *bus = context; ++ u16 page, r, lo, hi; ++ int ret; ++ ++ page = (reg >> 6) & 0x3ff; ++ r = (reg >> 2) & 0xf; ++ lo = val & 0xffff; ++ hi = val >> 16; ++ ++ /* MT7530 uses 31 as the pseudo port */ ++ ret = bus->write(bus, 0x1f, 0x1f, page); ++ if (ret < 0) ++ return ret; ++ ++ ret = bus->write(bus, 0x1f, r, lo); ++ if (ret < 0) ++ return ret; ++ ++ ret = bus->write(bus, 0x1f, 0x10, hi); ++ return ret; ++} ++ ++static int ++mt7530_regmap_read(void *context, unsigned int reg, unsigned int *val) ++{ ++ struct mii_bus *bus = context; ++ u16 page, r, lo, hi; ++ int ret; ++ ++ page = (reg >> 6) & 0x3ff; ++ r = (reg >> 2) & 0xf; ++ ++ /* MT7530 uses 31 as the pseudo port */ ++ ret = bus->write(bus, 0x1f, 0x1f, page); ++ if (ret < 0) ++ return ret; ++ ++ lo = bus->read(bus, 0x1f, r); ++ hi = bus->read(bus, 0x1f, 0x10); ++ ++ *val = (hi << 16) | (lo & 0xffff); ++ ++ return 0; ++} ++ ++static void ++mt7530_mdio_regmap_lock(void *mdio_lock) ++{ ++ mutex_lock_nested(mdio_lock, MDIO_MUTEX_NESTED); ++} ++ ++static void ++mt7530_mdio_regmap_unlock(void *mdio_lock) ++{ ++ mutex_unlock(mdio_lock); ++} ++ ++static const struct regmap_bus mt7530_regmap_bus = { ++ .reg_write = mt7530_regmap_write, ++ .reg_read = mt7530_regmap_read, ++}; ++ ++static int ++mt7531_create_sgmii(struct mt7530_priv *priv) ++{ ++ struct regmap_config *mt7531_pcs_config[2]; ++ struct phylink_pcs *pcs; ++ struct regmap *regmap; ++ int i, ret = 0; ++ ++ for (i = 0; i < 2; i++) { ++ mt7531_pcs_config[i] = devm_kzalloc(priv->dev, ++ sizeof(struct regmap_config), ++ GFP_KERNEL); ++ if (!mt7531_pcs_config[i]) { ++ ret = -ENOMEM; ++ break; ++ } ++ ++ mt7531_pcs_config[i]->name = i ? "port6" : "port5"; ++ mt7531_pcs_config[i]->reg_bits = 16; ++ mt7531_pcs_config[i]->val_bits = 32; ++ mt7531_pcs_config[i]->reg_stride = 4; ++ mt7531_pcs_config[i]->reg_base = MT7531_SGMII_REG_BASE(5 + i); ++ mt7531_pcs_config[i]->max_register = 0x17c; ++ mt7531_pcs_config[i]->lock = mt7530_mdio_regmap_lock; ++ mt7531_pcs_config[i]->unlock = mt7530_mdio_regmap_unlock; ++ mt7531_pcs_config[i]->lock_arg = &priv->bus->mdio_lock; ++ ++ regmap = devm_regmap_init(priv->dev, ++ &mt7530_regmap_bus, priv->bus, ++ mt7531_pcs_config[i]); ++ if (IS_ERR(regmap)) { ++ ret = PTR_ERR(regmap); ++ break; ++ } ++ pcs = mtk_pcs_lynxi_create(priv->dev, regmap, ++ MT7531_PHYA_CTRL_SIGNAL3, 0); ++ if (!pcs) { ++ ret = -ENXIO; ++ break; ++ } ++ priv->ports[5 + i].sgmii_pcs = pcs; ++ } ++ ++ if (ret && i) ++ mtk_pcs_lynxi_destroy(priv->ports[5].sgmii_pcs); ++ ++ return ret; ++} ++ ++static const struct of_device_id mt7530_of_match[] = { ++ { .compatible = "mediatek,mt7621", .data = &mt753x_table[ID_MT7621], }, ++ { .compatible = "mediatek,mt7530", .data = &mt753x_table[ID_MT7530], }, ++ { .compatible = "mediatek,mt7531", .data = &mt753x_table[ID_MT7531], }, ++ { /* sentinel */ }, ++}; ++MODULE_DEVICE_TABLE(of, mt7530_of_match); ++ ++static int ++mt7530_probe(struct mdio_device *mdiodev) ++{ ++ static struct regmap_config *regmap_config; ++ struct mt7530_priv *priv; ++ struct device_node *dn; ++ int ret; ++ ++ dn = mdiodev->dev.of_node; ++ ++ priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL); ++ if (!priv) ++ return -ENOMEM; ++ ++ priv->bus = mdiodev->bus; ++ priv->dev = &mdiodev->dev; ++ ++ ret = mt7530_probe_common(priv); ++ if (ret) ++ return ret; ++ ++ /* Use medatek,mcm property to distinguish hardware type that would ++ * cause a little bit differences on power-on sequence. ++ * Not MCM that indicates switch works as the remote standalone ++ * integrated circuit so the GPIO pin would be used to complete ++ * the reset, otherwise memory-mapped register accessing used ++ * through syscon provides in the case of MCM. ++ */ ++ priv->mcm = of_property_read_bool(dn, "mediatek,mcm"); ++ if (priv->mcm) { ++ dev_info(&mdiodev->dev, "MT7530 adapts as multi-chip module\n"); ++ ++ priv->rstc = devm_reset_control_get(&mdiodev->dev, "mcm"); ++ if (IS_ERR(priv->rstc)) { ++ dev_err(&mdiodev->dev, "Couldn't get our reset line\n"); ++ return PTR_ERR(priv->rstc); ++ } ++ } else { ++ priv->reset = devm_gpiod_get_optional(&mdiodev->dev, "reset", ++ GPIOD_OUT_LOW); ++ if (IS_ERR(priv->reset)) { ++ dev_err(&mdiodev->dev, "Couldn't get our reset line\n"); ++ return PTR_ERR(priv->reset); ++ } ++ } ++ ++ if (priv->id == ID_MT7530) { ++ priv->core_pwr = devm_regulator_get(&mdiodev->dev, "core"); ++ if (IS_ERR(priv->core_pwr)) ++ return PTR_ERR(priv->core_pwr); ++ ++ priv->io_pwr = devm_regulator_get(&mdiodev->dev, "io"); ++ if (IS_ERR(priv->io_pwr)) ++ return PTR_ERR(priv->io_pwr); ++ } ++ ++ regmap_config = devm_kzalloc(&mdiodev->dev, sizeof(*regmap_config), ++ GFP_KERNEL); ++ if (!regmap_config) ++ return -ENOMEM; ++ ++ regmap_config->reg_bits = 16; ++ regmap_config->val_bits = 32; ++ regmap_config->reg_stride = 4; ++ regmap_config->max_register = MT7530_CREV; ++ regmap_config->disable_locking = true; ++ priv->regmap = devm_regmap_init(priv->dev, &mt7530_regmap_bus, ++ priv->bus, regmap_config); ++ if (IS_ERR(priv->regmap)) ++ return PTR_ERR(priv->regmap); ++ ++ if (priv->id == ID_MT7531) { ++ ret = mt7531_create_sgmii(priv); ++ if (ret) ++ return ret; ++ } ++ ++ return dsa_register_switch(priv->ds); ++} ++ ++static void ++mt7530_remove(struct mdio_device *mdiodev) ++{ ++ struct mt7530_priv *priv = dev_get_drvdata(&mdiodev->dev); ++ int ret = 0, i; ++ ++ if (!priv) ++ return; ++ ++ ret = regulator_disable(priv->core_pwr); ++ if (ret < 0) ++ dev_err(priv->dev, ++ "Failed to disable core power: %d\n", ret); ++ ++ ret = regulator_disable(priv->io_pwr); ++ if (ret < 0) ++ dev_err(priv->dev, "Failed to disable io pwr: %d\n", ++ ret); ++ ++ mt7530_remove_common(priv); ++ ++ for (i = 0; i < 2; ++i) ++ mtk_pcs_lynxi_destroy(priv->ports[5 + i].sgmii_pcs); ++} ++ ++static void mt7530_shutdown(struct mdio_device *mdiodev) ++{ ++ struct mt7530_priv *priv = dev_get_drvdata(&mdiodev->dev); ++ ++ if (!priv) ++ return; ++ ++ dsa_switch_shutdown(priv->ds); ++ ++ dev_set_drvdata(&mdiodev->dev, NULL); ++} ++ ++static struct mdio_driver mt7530_mdio_driver = { ++ .probe = mt7530_probe, ++ .remove = mt7530_remove, ++ .shutdown = mt7530_shutdown, ++ .mdiodrv.driver = { ++ .name = "mt7530-mdio", ++ .of_match_table = mt7530_of_match, ++ }, ++}; ++ ++mdio_module_driver(mt7530_mdio_driver); ++ ++MODULE_AUTHOR("Sean Wang "); ++MODULE_DESCRIPTION("Driver for Mediatek MT7530 Switch (MDIO)"); ++MODULE_LICENSE("GPL"); +--- a/drivers/net/dsa/mt7530.c ++++ b/drivers/net/dsa/mt7530.c +@@ -14,7 +14,6 @@ + #include + #include + #include +-#include + #include + #include + #include +@@ -192,31 +191,6 @@ core_clear(struct mt7530_priv *priv, u32 + } + + static int +-mt7530_regmap_write(void *context, unsigned int reg, unsigned int val) +-{ +- struct mii_bus *bus = context; +- u16 page, r, lo, hi; +- int ret; +- +- page = (reg >> 6) & 0x3ff; +- r = (reg >> 2) & 0xf; +- lo = val & 0xffff; +- hi = val >> 16; +- +- /* MT7530 uses 31 as the pseudo port */ +- ret = bus->write(bus, 0x1f, 0x1f, page); +- if (ret < 0) +- return ret; +- +- ret = bus->write(bus, 0x1f, r, lo); +- if (ret < 0) +- return ret; +- +- ret = bus->write(bus, 0x1f, 0x10, hi); +- return ret; +-} +- +-static int + mt7530_mii_write(struct mt7530_priv *priv, u32 reg, u32 val) + { + int ret; +@@ -230,29 +204,6 @@ mt7530_mii_write(struct mt7530_priv *pri + return ret; + } + +-static int +-mt7530_regmap_read(void *context, unsigned int reg, unsigned int *val) +-{ +- struct mii_bus *bus = context; +- u16 page, r, lo, hi; +- int ret; +- +- page = (reg >> 6) & 0x3ff; +- r = (reg >> 2) & 0xf; +- +- /* MT7530 uses 31 as the pseudo port */ +- ret = bus->write(bus, 0x1f, 0x1f, page); +- if (ret < 0) +- return ret; +- +- lo = bus->read(bus, 0x1f, r); +- hi = bus->read(bus, 0x1f, 0x10); +- +- *val = (hi << 16) | (lo & 0xffff); +- +- return 0; +-} +- + static u32 + mt7530_mii_read(struct mt7530_priv *priv, u32 reg) + { +@@ -2957,72 +2908,6 @@ static const struct phylink_pcs_ops mt75 + .pcs_an_restart = mt7530_pcs_an_restart, + }; + +-static void +-mt7530_mdio_regmap_lock(void *mdio_lock) +-{ +- mutex_lock_nested(mdio_lock, MDIO_MUTEX_NESTED); +-} +- +-static void +-mt7530_mdio_regmap_unlock(void *mdio_lock) +-{ +- mutex_unlock(mdio_lock); +-} +- +-static const struct regmap_bus mt7530_regmap_bus = { +- .reg_write = mt7530_regmap_write, +- .reg_read = mt7530_regmap_read, +-}; +- +-static int +-mt7531_create_sgmii(struct mt7530_priv *priv) +-{ +- struct regmap_config *mt7531_pcs_config[2]; +- struct phylink_pcs *pcs; +- struct regmap *regmap; +- int i, ret = 0; +- +- for (i = 0; i < 2; i++) { +- mt7531_pcs_config[i] = devm_kzalloc(priv->dev, +- sizeof(struct regmap_config), +- GFP_KERNEL); +- if (!mt7531_pcs_config[i]) { +- ret = -ENOMEM; +- break; +- } +- +- mt7531_pcs_config[i]->name = i ? "port6" : "port5"; +- mt7531_pcs_config[i]->reg_bits = 16; +- mt7531_pcs_config[i]->val_bits = 32; +- mt7531_pcs_config[i]->reg_stride = 4; +- mt7531_pcs_config[i]->reg_base = MT7531_SGMII_REG_BASE(5 + i); +- mt7531_pcs_config[i]->max_register = 0x17c; +- mt7531_pcs_config[i]->lock = mt7530_mdio_regmap_lock; +- mt7531_pcs_config[i]->unlock = mt7530_mdio_regmap_unlock; +- mt7531_pcs_config[i]->lock_arg = &priv->bus->mdio_lock; +- +- regmap = devm_regmap_init(priv->dev, +- &mt7530_regmap_bus, priv->bus, +- mt7531_pcs_config[i]); +- if (IS_ERR(regmap)) { +- ret = PTR_ERR(regmap); +- break; +- } +- pcs = mtk_pcs_lynxi_create(priv->dev, regmap, +- MT7531_PHYA_CTRL_SIGNAL3, 0); +- if (!pcs) { +- ret = -ENXIO; +- break; +- } +- priv->ports[5 + i].sgmii_pcs = pcs; +- } +- +- if (ret && i) +- mtk_pcs_lynxi_destroy(priv->ports[5].sgmii_pcs); +- +- return ret; +-} +- + static int + mt753x_setup(struct dsa_switch *ds) + { +@@ -3081,7 +2966,7 @@ static int mt753x_set_mac_eee(struct dsa + return 0; + } + +-static const struct dsa_switch_ops mt7530_switch_ops = { ++const struct dsa_switch_ops mt7530_switch_ops = { + .get_tag_protocol = mtk_get_tag_protocol, + .setup = mt753x_setup, + .get_strings = mt7530_get_strings, +@@ -3115,8 +3000,9 @@ static const struct dsa_switch_ops mt753 + .get_mac_eee = mt753x_get_mac_eee, + .set_mac_eee = mt753x_set_mac_eee, + }; ++EXPORT_SYMBOL_GPL(mt7530_switch_ops); + +-static const struct mt753x_info mt753x_table[] = { ++const struct mt753x_info mt753x_table[] = { + [ID_MT7621] = { + .id = ID_MT7621, + .pcs_ops = &mt7530_pcs_ops, +@@ -3149,16 +3035,9 @@ static const struct mt753x_info mt753x_t + .mac_port_config = mt7531_mac_config, + }, + }; ++EXPORT_SYMBOL_GPL(mt753x_table); + +-static const struct of_device_id mt7530_of_match[] = { +- { .compatible = "mediatek,mt7621", .data = &mt753x_table[ID_MT7621], }, +- { .compatible = "mediatek,mt7530", .data = &mt753x_table[ID_MT7530], }, +- { .compatible = "mediatek,mt7531", .data = &mt753x_table[ID_MT7531], }, +- { /* sentinel */ }, +-}; +-MODULE_DEVICE_TABLE(of, mt7530_of_match); +- +-static int ++int + mt7530_probe_common(struct mt7530_priv *priv) + { + struct device *dev = priv->dev; +@@ -3195,88 +3074,9 @@ mt7530_probe_common(struct mt7530_priv * + + return 0; + } ++EXPORT_SYMBOL_GPL(mt7530_probe_common); + +-static int +-mt7530_probe(struct mdio_device *mdiodev) +-{ +- static struct regmap_config *regmap_config; +- struct mt7530_priv *priv; +- struct device_node *dn; +- int ret; +- +- dn = mdiodev->dev.of_node; +- +- priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL); +- if (!priv) +- return -ENOMEM; +- +- priv->bus = mdiodev->bus; +- priv->dev = &mdiodev->dev; +- +- ret = mt7530_probe_common(priv); +- if (ret) +- return ret; +- +- /* Use medatek,mcm property to distinguish hardware type that would +- * cause a little bit differences on power-on sequence. +- * Not MCM that indicates switch works as the remote standalone +- * integrated circuit so the GPIO pin would be used to complete +- * the reset, otherwise memory-mapped register accessing used +- * through syscon provides in the case of MCM. +- */ +- priv->mcm = of_property_read_bool(dn, "mediatek,mcm"); +- if (priv->mcm) { +- dev_info(&mdiodev->dev, "MT7530 adapts as multi-chip module\n"); +- +- priv->rstc = devm_reset_control_get(&mdiodev->dev, "mcm"); +- if (IS_ERR(priv->rstc)) { +- dev_err(&mdiodev->dev, "Couldn't get our reset line\n"); +- return PTR_ERR(priv->rstc); +- } +- } else { +- priv->reset = devm_gpiod_get_optional(&mdiodev->dev, "reset", +- GPIOD_OUT_LOW); +- if (IS_ERR(priv->reset)) { +- dev_err(&mdiodev->dev, "Couldn't get our reset line\n"); +- return PTR_ERR(priv->reset); +- } +- } +- +- if (priv->id == ID_MT7530) { +- priv->core_pwr = devm_regulator_get(&mdiodev->dev, "core"); +- if (IS_ERR(priv->core_pwr)) +- return PTR_ERR(priv->core_pwr); +- +- priv->io_pwr = devm_regulator_get(&mdiodev->dev, "io"); +- if (IS_ERR(priv->io_pwr)) +- return PTR_ERR(priv->io_pwr); +- } +- +- regmap_config = devm_kzalloc(&mdiodev->dev, sizeof(*regmap_config), +- GFP_KERNEL); +- if (!regmap_config) +- return -ENOMEM; +- +- regmap_config->reg_bits = 16; +- regmap_config->val_bits = 32; +- regmap_config->reg_stride = 4; +- regmap_config->max_register = MT7530_CREV; +- regmap_config->disable_locking = true; +- priv->regmap = devm_regmap_init(priv->dev, &mt7530_regmap_bus, +- priv->bus, regmap_config); +- if (IS_ERR(priv->regmap)) +- return PTR_ERR(priv->regmap); +- +- if (priv->id == ID_MT7531) { +- ret = mt7531_create_sgmii(priv); +- if (ret) +- return ret; +- } +- +- return dsa_register_switch(priv->ds); +-} +- +-static void ++void + mt7530_remove_common(struct mt7530_priv *priv) + { + if (priv->irq) +@@ -3286,55 +3086,7 @@ mt7530_remove_common(struct mt7530_priv + + mutex_destroy(&priv->reg_mutex); + } +- +-static void +-mt7530_remove(struct mdio_device *mdiodev) +-{ +- struct mt7530_priv *priv = dev_get_drvdata(&mdiodev->dev); +- int ret = 0, i; +- +- if (!priv) +- return; +- +- ret = regulator_disable(priv->core_pwr); +- if (ret < 0) +- dev_err(priv->dev, +- "Failed to disable core power: %d\n", ret); +- +- ret = regulator_disable(priv->io_pwr); +- if (ret < 0) +- dev_err(priv->dev, "Failed to disable io pwr: %d\n", +- ret); +- +- mt7530_remove_common(priv); +- +- for (i = 0; i < 2; ++i) +- mtk_pcs_lynxi_destroy(priv->ports[5 + i].sgmii_pcs); +-} +- +-static void mt7530_shutdown(struct mdio_device *mdiodev) +-{ +- struct mt7530_priv *priv = dev_get_drvdata(&mdiodev->dev); +- +- if (!priv) +- return; +- +- dsa_switch_shutdown(priv->ds); +- +- dev_set_drvdata(&mdiodev->dev, NULL); +-} +- +-static struct mdio_driver mt7530_mdio_driver = { +- .probe = mt7530_probe, +- .remove = mt7530_remove, +- .shutdown = mt7530_shutdown, +- .mdiodrv.driver = { +- .name = "mt7530", +- .of_match_table = mt7530_of_match, +- }, +-}; +- +-mdio_module_driver(mt7530_mdio_driver); ++EXPORT_SYMBOL_GPL(mt7530_remove_common); + + MODULE_AUTHOR("Sean Wang "); + MODULE_DESCRIPTION("Driver for Mediatek MT7530 Switch"); +--- a/drivers/net/dsa/mt7530.h ++++ b/drivers/net/dsa/mt7530.h +@@ -807,4 +807,10 @@ static inline void INIT_MT7530_DUMMY_POL + p->reg = reg; + } + ++int mt7530_probe_common(struct mt7530_priv *priv); ++void mt7530_remove_common(struct mt7530_priv *priv); ++ ++extern const struct dsa_switch_ops mt7530_switch_ops; ++extern const struct mt753x_info mt753x_table[]; ++ + #endif /* __MT7530_H */ diff --git a/target/linux/generic/backport-6.1/790-v6.4-0011-net-dsa-mt7530-skip-locking-if-MDIO-bus-isn-t-presen.patch b/target/linux/generic/backport-6.1/790-v6.4-0011-net-dsa-mt7530-skip-locking-if-MDIO-bus-isn-t-presen.patch new file mode 100644 index 0000000000..01011ed1a0 --- /dev/null +++ b/target/linux/generic/backport-6.1/790-v6.4-0011-net-dsa-mt7530-skip-locking-if-MDIO-bus-isn-t-presen.patch @@ -0,0 +1,47 @@ +From a52cadbf76593f8fcb2f4f62cb006e3f2a22ad06 Mon Sep 17 00:00:00 2001 +From: Daniel Golle +Date: Mon, 3 Apr 2023 02:19:28 +0100 +Subject: [PATCH 11/13] net: dsa: mt7530: skip locking if MDIO bus isn't + present + +As MT7530 and MT7531 internally use 32-bit wide registers, each access +to any register of the switch requires several operations on the MDIO +bus. Hence if there is congruent access, e.g. due to PCS or PHY +polling, this can mess up and interfere with another ongoing register +access sequence. + +However, the MDIO bus mutex is only relevant for MDIO-connected +switches. Prepare switches which have there registers directly mapped +into the SoCs register space via MMIO which do not require such +locking. There we can simply use regmap's default locking mechanism. + +Hence guard mutex operations to only be performed in case of MDIO +connected switches. + +Signed-off-by: Daniel Golle +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + drivers/net/dsa/mt7530.c | 6 ++++-- + 1 file changed, 4 insertions(+), 2 deletions(-) + +--- a/drivers/net/dsa/mt7530.c ++++ b/drivers/net/dsa/mt7530.c +@@ -144,13 +144,15 @@ err: + static void + mt7530_mutex_lock(struct mt7530_priv *priv) + { +- mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); ++ if (priv->bus) ++ mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED); + } + + static void + mt7530_mutex_unlock(struct mt7530_priv *priv) + { +- mutex_unlock(&priv->bus->mdio_lock); ++ if (priv->bus) ++ mutex_unlock(&priv->bus->mdio_lock); + } + + static void diff --git a/target/linux/generic/backport-6.1/790-v6.4-0012-net-dsa-mt7530-introduce-driver-for-MT7988-built-in-.patch b/target/linux/generic/backport-6.1/790-v6.4-0012-net-dsa-mt7530-introduce-driver-for-MT7988-built-in-.patch new file mode 100644 index 0000000000..aeaf9f8467 --- /dev/null +++ b/target/linux/generic/backport-6.1/790-v6.4-0012-net-dsa-mt7530-introduce-driver-for-MT7988-built-in-.patch @@ -0,0 +1,421 @@ +From b361015763fedea439f13b336b15ef7bdf1f7d4f Mon Sep 17 00:00:00 2001 +From: Daniel Golle +Date: Mon, 3 Apr 2023 02:19:40 +0100 +Subject: [PATCH 12/13] net: dsa: mt7530: introduce driver for MT7988 built-in + switch + +Add driver for the built-in Gigabit Ethernet switch which can be found +in the MediaTek MT7988 SoC. + +The switch shares most of its design with MT7530 and MT7531, but has +it's registers mapped into the SoCs register space rather than being +connected externally or internally via MDIO. + +Introduce a new platform driver to support that. + +Signed-off-by: Daniel Golle +Reviewed-by: Andrew Lunn +Signed-off-by: David S. Miller +--- + MAINTAINERS | 2 + + drivers/net/dsa/Kconfig | 12 +++ + drivers/net/dsa/Makefile | 1 + + drivers/net/dsa/mt7530-mmio.c | 101 +++++++++++++++++++++++++ + drivers/net/dsa/mt7530.c | 137 +++++++++++++++++++++++++++++++++- + drivers/net/dsa/mt7530.h | 12 +-- + 6 files changed, 255 insertions(+), 10 deletions(-) + create mode 100644 drivers/net/dsa/mt7530-mmio.c + +--- a/MAINTAINERS ++++ b/MAINTAINERS +@@ -13058,9 +13058,11 @@ MEDIATEK SWITCH DRIVER + M: Sean Wang + M: Landen Chao + M: DENG Qingfang ++M: Daniel Golle + L: netdev@vger.kernel.org + S: Maintained + F: drivers/net/dsa/mt7530-mdio.c ++F: drivers/net/dsa/mt7530-mmio.c + F: drivers/net/dsa/mt7530.* + F: net/dsa/tag_mtk.c + +--- a/drivers/net/dsa/Kconfig ++++ b/drivers/net/dsa/Kconfig +@@ -38,6 +38,7 @@ config NET_DSA_MT7530 + select NET_DSA_TAG_MTK + select MEDIATEK_GE_PHY + imply NET_DSA_MT7530_MDIO ++ imply NET_DSA_MT7530_MMIO + help + This enables support for the MediaTek MT7530 and MT7531 Ethernet + switch chips. Multi-chip module MT7530 in MT7621AT, MT7621DAT, +@@ -54,6 +55,17 @@ config NET_DSA_MT7530_MDIO + module MT7530 which can be found in the MT7621AT, MT7621DAT, + MT7621ST and MT7623AI SoCs. + ++config NET_DSA_MT7530_MMIO ++ tristate "MediaTek MT7530 MMIO interface driver" ++ depends on NET_DSA_MT7530 ++ depends on HAS_IOMEM ++ help ++ This enables support for the built-in Ethernet switch found ++ in the MediaTek MT7988 SoC. ++ The switch is a similar design as MT7531, but the switch registers ++ are directly mapped into the SoCs register space rather than being ++ accessible via MDIO. ++ + config NET_DSA_MV88E6060 + tristate "Marvell 88E6060 ethernet switch chip support" + select NET_DSA_TAG_TRAILER +--- a/drivers/net/dsa/Makefile ++++ b/drivers/net/dsa/Makefile +@@ -8,6 +8,7 @@ endif + obj-$(CONFIG_NET_DSA_LANTIQ_GSWIP) += lantiq_gswip.o + obj-$(CONFIG_NET_DSA_MT7530) += mt7530.o + obj-$(CONFIG_NET_DSA_MT7530_MDIO) += mt7530-mdio.o ++obj-$(CONFIG_NET_DSA_MT7530_MMIO) += mt7530-mmio.o + obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e6060.o + obj-$(CONFIG_NET_DSA_RZN1_A5PSW) += rzn1_a5psw.o + obj-$(CONFIG_NET_DSA_SMSC_LAN9303) += lan9303-core.o +--- /dev/null ++++ b/drivers/net/dsa/mt7530-mmio.c +@@ -0,0 +1,101 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++ ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "mt7530.h" ++ ++static const struct of_device_id mt7988_of_match[] = { ++ { .compatible = "mediatek,mt7988-switch", .data = &mt753x_table[ID_MT7988], }, ++ { /* sentinel */ }, ++}; ++MODULE_DEVICE_TABLE(of, mt7988_of_match); ++ ++static int ++mt7988_probe(struct platform_device *pdev) ++{ ++ static struct regmap_config *sw_regmap_config; ++ struct mt7530_priv *priv; ++ void __iomem *base_addr; ++ int ret; ++ ++ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); ++ if (!priv) ++ return -ENOMEM; ++ ++ priv->bus = NULL; ++ priv->dev = &pdev->dev; ++ ++ ret = mt7530_probe_common(priv); ++ if (ret) ++ return ret; ++ ++ priv->rstc = devm_reset_control_get(&pdev->dev, NULL); ++ if (IS_ERR(priv->rstc)) { ++ dev_err(&pdev->dev, "Couldn't get our reset line\n"); ++ return PTR_ERR(priv->rstc); ++ } ++ ++ base_addr = devm_platform_ioremap_resource(pdev, 0); ++ if (IS_ERR(base_addr)) { ++ dev_err(&pdev->dev, "cannot request I/O memory space\n"); ++ return -ENXIO; ++ } ++ ++ sw_regmap_config = devm_kzalloc(&pdev->dev, sizeof(*sw_regmap_config), GFP_KERNEL); ++ if (!sw_regmap_config) ++ return -ENOMEM; ++ ++ sw_regmap_config->name = "switch"; ++ sw_regmap_config->reg_bits = 16; ++ sw_regmap_config->val_bits = 32; ++ sw_regmap_config->reg_stride = 4; ++ sw_regmap_config->max_register = MT7530_CREV; ++ priv->regmap = devm_regmap_init_mmio(&pdev->dev, base_addr, sw_regmap_config); ++ if (IS_ERR(priv->regmap)) ++ return PTR_ERR(priv->regmap); ++ ++ return dsa_register_switch(priv->ds); ++} ++ ++static int ++mt7988_remove(struct platform_device *pdev) ++{ ++ struct mt7530_priv *priv = platform_get_drvdata(pdev); ++ ++ if (priv) ++ mt7530_remove_common(priv); ++ ++ return 0; ++} ++ ++static void mt7988_shutdown(struct platform_device *pdev) ++{ ++ struct mt7530_priv *priv = platform_get_drvdata(pdev); ++ ++ if (!priv) ++ return; ++ ++ dsa_switch_shutdown(priv->ds); ++ ++ dev_set_drvdata(&pdev->dev, NULL); ++} ++ ++static struct platform_driver mt7988_platform_driver = { ++ .probe = mt7988_probe, ++ .remove = mt7988_remove, ++ .shutdown = mt7988_shutdown, ++ .driver = { ++ .name = "mt7530-mmio", ++ .of_match_table = mt7988_of_match, ++ }, ++}; ++module_platform_driver(mt7988_platform_driver); ++ ++MODULE_AUTHOR("Daniel Golle "); ++MODULE_DESCRIPTION("Driver for Mediatek MT7530 Switch (MMIO)"); ++MODULE_LICENSE("GPL"); +--- a/drivers/net/dsa/mt7530.c ++++ b/drivers/net/dsa/mt7530.c +@@ -1989,6 +1989,47 @@ static const struct irq_domain_ops mt753 + }; + + static void ++mt7988_irq_mask(struct irq_data *d) ++{ ++ struct mt7530_priv *priv = irq_data_get_irq_chip_data(d); ++ ++ priv->irq_enable &= ~BIT(d->hwirq); ++ mt7530_mii_write(priv, MT7530_SYS_INT_EN, priv->irq_enable); ++} ++ ++static void ++mt7988_irq_unmask(struct irq_data *d) ++{ ++ struct mt7530_priv *priv = irq_data_get_irq_chip_data(d); ++ ++ priv->irq_enable |= BIT(d->hwirq); ++ mt7530_mii_write(priv, MT7530_SYS_INT_EN, priv->irq_enable); ++} ++ ++static struct irq_chip mt7988_irq_chip = { ++ .name = KBUILD_MODNAME, ++ .irq_mask = mt7988_irq_mask, ++ .irq_unmask = mt7988_irq_unmask, ++}; ++ ++static int ++mt7988_irq_map(struct irq_domain *domain, unsigned int irq, ++ irq_hw_number_t hwirq) ++{ ++ irq_set_chip_data(irq, domain->host_data); ++ irq_set_chip_and_handler(irq, &mt7988_irq_chip, handle_simple_irq); ++ irq_set_nested_thread(irq, true); ++ irq_set_noprobe(irq); ++ ++ return 0; ++} ++ ++static const struct irq_domain_ops mt7988_irq_domain_ops = { ++ .map = mt7988_irq_map, ++ .xlate = irq_domain_xlate_onecell, ++}; ++ ++static void + mt7530_setup_mdio_irq(struct mt7530_priv *priv) + { + struct dsa_switch *ds = priv->ds; +@@ -2022,8 +2063,15 @@ mt7530_setup_irq(struct mt7530_priv *pri + return priv->irq ? : -EINVAL; + } + +- priv->irq_domain = irq_domain_add_linear(np, MT7530_NUM_PHYS, +- &mt7530_irq_domain_ops, priv); ++ if (priv->id == ID_MT7988) ++ priv->irq_domain = irq_domain_add_linear(np, MT7530_NUM_PHYS, ++ &mt7988_irq_domain_ops, ++ priv); ++ else ++ priv->irq_domain = irq_domain_add_linear(np, MT7530_NUM_PHYS, ++ &mt7530_irq_domain_ops, ++ priv); ++ + if (!priv->irq_domain) { + dev_err(dev, "failed to create IRQ domain\n"); + return -ENOMEM; +@@ -2520,6 +2568,25 @@ static void mt7531_mac_port_get_caps(str + } + } + ++static void mt7988_mac_port_get_caps(struct dsa_switch *ds, int port, ++ struct phylink_config *config) ++{ ++ phy_interface_zero(config->supported_interfaces); ++ ++ switch (port) { ++ case 0 ... 4: /* Internal phy */ ++ __set_bit(PHY_INTERFACE_MODE_INTERNAL, ++ config->supported_interfaces); ++ break; ++ ++ case 6: ++ __set_bit(PHY_INTERFACE_MODE_INTERNAL, ++ config->supported_interfaces); ++ config->mac_capabilities = MAC_ASYM_PAUSE | MAC_SYM_PAUSE | ++ MAC_10000FD; ++ } ++} ++ + static int + mt753x_pad_setup(struct dsa_switch *ds, const struct phylink_link_state *state) + { +@@ -2596,6 +2663,17 @@ static bool mt753x_is_mac_port(u32 port) + } + + static int ++mt7988_mac_config(struct dsa_switch *ds, int port, unsigned int mode, ++ phy_interface_t interface) ++{ ++ if (dsa_is_cpu_port(ds, port) && ++ interface == PHY_INTERFACE_MODE_INTERNAL) ++ return 0; ++ ++ return -EINVAL; ++} ++ ++static int + mt7531_mac_config(struct dsa_switch *ds, int port, unsigned int mode, + phy_interface_t interface) + { +@@ -2665,7 +2743,8 @@ mt753x_phylink_mac_config(struct dsa_swi + + switch (port) { + case 0 ... 4: /* Internal phy */ +- if (state->interface != PHY_INTERFACE_MODE_GMII) ++ if (state->interface != PHY_INTERFACE_MODE_GMII && ++ state->interface != PHY_INTERFACE_MODE_INTERNAL) + goto unsupported; + break; + case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */ +@@ -2743,7 +2822,8 @@ static void mt753x_phylink_mac_link_up(s + /* MT753x MAC works in 1G full duplex mode for all up-clocked + * variants. + */ +- if (interface == PHY_INTERFACE_MODE_TRGMII || ++ if (interface == PHY_INTERFACE_MODE_INTERNAL || ++ interface == PHY_INTERFACE_MODE_TRGMII || + (phy_interface_mode_is_8023z(interface))) { + speed = SPEED_1000; + duplex = DUPLEX_FULL; +@@ -2823,6 +2903,21 @@ mt7531_cpu_port_config(struct dsa_switch + return 0; + } + ++static int ++mt7988_cpu_port_config(struct dsa_switch *ds, int port) ++{ ++ struct mt7530_priv *priv = ds->priv; ++ ++ mt7530_write(priv, MT7530_PMCR_P(port), ++ PMCR_CPU_PORT_SETTING(priv->id)); ++ ++ mt753x_phylink_mac_link_up(ds, port, MLO_AN_FIXED, ++ PHY_INTERFACE_MODE_INTERNAL, NULL, ++ SPEED_10000, DUPLEX_FULL, true, true); ++ ++ return 0; ++} ++ + static void mt753x_phylink_get_caps(struct dsa_switch *ds, int port, + struct phylink_config *config) + { +@@ -2968,6 +3063,27 @@ static int mt753x_set_mac_eee(struct dsa + return 0; + } + ++static int mt7988_pad_setup(struct dsa_switch *ds, phy_interface_t interface) ++{ ++ return 0; ++} ++ ++static int mt7988_setup(struct dsa_switch *ds) ++{ ++ struct mt7530_priv *priv = ds->priv; ++ ++ /* Reset the switch */ ++ reset_control_assert(priv->rstc); ++ usleep_range(20, 50); ++ reset_control_deassert(priv->rstc); ++ usleep_range(20, 50); ++ ++ /* Reset the switch PHYs */ ++ mt7530_write(priv, MT7530_SYS_CTRL, SYS_CTRL_PHY_RST); ++ ++ return mt7531_setup_common(ds); ++} ++ + const struct dsa_switch_ops mt7530_switch_ops = { + .get_tag_protocol = mtk_get_tag_protocol, + .setup = mt753x_setup, +@@ -3036,6 +3152,17 @@ const struct mt753x_info mt753x_table[] + .mac_port_get_caps = mt7531_mac_port_get_caps, + .mac_port_config = mt7531_mac_config, + }, ++ [ID_MT7988] = { ++ .id = ID_MT7988, ++ .pcs_ops = &mt7530_pcs_ops, ++ .sw_setup = mt7988_setup, ++ .phy_read = mt7531_ind_phy_read, ++ .phy_write = mt7531_ind_phy_write, ++ .pad_setup = mt7988_pad_setup, ++ .cpu_port_config = mt7988_cpu_port_config, ++ .mac_port_get_caps = mt7988_mac_port_get_caps, ++ .mac_port_config = mt7988_mac_config, ++ }, + }; + EXPORT_SYMBOL_GPL(mt753x_table); + +--- a/drivers/net/dsa/mt7530.h ++++ b/drivers/net/dsa/mt7530.h +@@ -18,6 +18,7 @@ enum mt753x_id { + ID_MT7530 = 0, + ID_MT7621 = 1, + ID_MT7531 = 2, ++ ID_MT7988 = 3, + }; + + #define NUM_TRGMII_CTRL 5 +@@ -54,11 +55,11 @@ enum mt753x_id { + #define MT7531_MIRROR_PORT_SET(x) (((x) & MIRROR_MASK) << 16) + #define MT7531_CPU_PMAP_MASK GENMASK(7, 0) + +-#define MT753X_MIRROR_REG(id) (((id) == ID_MT7531) ? \ ++#define MT753X_MIRROR_REG(id) ((((id) == ID_MT7531) || ((id) == ID_MT7988)) ? \ + MT7531_CFC : MT7530_MFC) +-#define MT753X_MIRROR_EN(id) (((id) == ID_MT7531) ? \ ++#define MT753X_MIRROR_EN(id) ((((id) == ID_MT7531) || ((id) == ID_MT7988)) ? \ + MT7531_MIRROR_EN : MIRROR_EN) +-#define MT753X_MIRROR_MASK(id) (((id) == ID_MT7531) ? \ ++#define MT753X_MIRROR_MASK(id) ((((id) == ID_MT7531) || ((id) == ID_MT7988)) ? \ + MT7531_MIRROR_MASK : MIRROR_MASK) + + /* Registers for BPDU and PAE frame control*/ +@@ -295,9 +296,8 @@ enum mt7530_vlan_port_acc_frm { + MT7531_FORCE_DPX | \ + MT7531_FORCE_RX_FC | \ + MT7531_FORCE_TX_FC) +-#define PMCR_FORCE_MODE_ID(id) (((id) == ID_MT7531) ? \ +- MT7531_FORCE_MODE : \ +- PMCR_FORCE_MODE) ++#define PMCR_FORCE_MODE_ID(id) ((((id) == ID_MT7531) || ((id) == ID_MT7988)) ? \ ++ MT7531_FORCE_MODE : PMCR_FORCE_MODE) + #define PMCR_LINK_SETTINGS_MASK (PMCR_TX_EN | PMCR_FORCE_SPEED_1000 | \ + PMCR_RX_EN | PMCR_FORCE_SPEED_100 | \ + PMCR_TX_FC_EN | PMCR_RX_FC_EN | \ diff --git a/target/linux/generic/backport-6.1/790-v6.4-0013-net-dsa-mt7530-fix-support-for-MT7531BE.patch b/target/linux/generic/backport-6.1/790-v6.4-0013-net-dsa-mt7530-fix-support-for-MT7531BE.patch new file mode 100644 index 0000000000..074472f6dc --- /dev/null +++ b/target/linux/generic/backport-6.1/790-v6.4-0013-net-dsa-mt7530-fix-support-for-MT7531BE.patch @@ -0,0 +1,118 @@ +From eb1dd407b4be7ca38166a38c56c8edf52c6a399f Mon Sep 17 00:00:00 2001 +From: Daniel Golle +Date: Sun, 16 Apr 2023 13:08:14 +0100 +Subject: [PATCH 13/13] net: dsa: mt7530: fix support for MT7531BE +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +There are two variants of the MT7531 switch IC which got different +features (and pins) regarding port 5: + * MT7531AE: SGMII/1000Base-X/2500Base-X SerDes PCS + * MT7531BE: RGMII + +Moving the creation of the SerDes PCS from mt753x_setup to mt7530_probe +with commit 6de285229773 ("net: dsa: mt7530: move SGMII PCS creation +to mt7530_probe function") works fine for MT7531AE which got two +instances of mtk-pcs-lynxi, however, MT7531BE requires mt7531_pll_setup +to setup clocks before the single PCS on port 6 (usually used as CPU +port) starts to work and hence the PCS creation failed on MT7531BE. + +Fix this by introducing a pointer to mt7531_create_sgmii function in +struct mt7530_priv and call it again at the end of mt753x_setup like it +was before commit 6de285229773 ("net: dsa: mt7530: move SGMII PCS +creation to mt7530_probe function"). + +Fixes: 6de285229773 ("net: dsa: mt7530: move SGMII PCS creation to mt7530_probe function") +Signed-off-by: Daniel Golle +Acked-by: Arınç ÜNAL +Link: https://lore.kernel.org/r/ZDvlLhhqheobUvOK@makrotopia.org +Signed-off-by: Jakub Kicinski +--- + drivers/net/dsa/mt7530-mdio.c | 16 ++++++++-------- + drivers/net/dsa/mt7530.c | 6 ++++++ + drivers/net/dsa/mt7530.h | 4 ++-- + 3 files changed, 16 insertions(+), 10 deletions(-) + +--- a/drivers/net/dsa/mt7530-mdio.c ++++ b/drivers/net/dsa/mt7530-mdio.c +@@ -81,14 +81,17 @@ static const struct regmap_bus mt7530_re + }; + + static int +-mt7531_create_sgmii(struct mt7530_priv *priv) ++mt7531_create_sgmii(struct mt7530_priv *priv, bool dual_sgmii) + { +- struct regmap_config *mt7531_pcs_config[2]; ++ struct regmap_config *mt7531_pcs_config[2] = {}; + struct phylink_pcs *pcs; + struct regmap *regmap; + int i, ret = 0; + +- for (i = 0; i < 2; i++) { ++ /* MT7531AE has two SGMII units for port 5 and port 6 ++ * MT7531BE has only one SGMII unit for port 6 ++ */ ++ for (i = dual_sgmii ? 0 : 1; i < 2; i++) { + mt7531_pcs_config[i] = devm_kzalloc(priv->dev, + sizeof(struct regmap_config), + GFP_KERNEL); +@@ -208,11 +211,8 @@ mt7530_probe(struct mdio_device *mdiodev + if (IS_ERR(priv->regmap)) + return PTR_ERR(priv->regmap); + +- if (priv->id == ID_MT7531) { +- ret = mt7531_create_sgmii(priv); +- if (ret) +- return ret; +- } ++ if (priv->id == ID_MT7531) ++ priv->create_sgmii = mt7531_create_sgmii; + + return dsa_register_switch(priv->ds); + } +--- a/drivers/net/dsa/mt7530.c ++++ b/drivers/net/dsa/mt7530.c +@@ -3030,6 +3030,12 @@ mt753x_setup(struct dsa_switch *ds) + if (ret && priv->irq) + mt7530_free_irq_common(priv); + ++ if (priv->create_sgmii) { ++ ret = priv->create_sgmii(priv, mt7531_dual_sgmii_supported(priv)); ++ if (ret && priv->irq) ++ mt7530_free_irq(priv); ++ } ++ + return ret; + } + +--- a/drivers/net/dsa/mt7530.h ++++ b/drivers/net/dsa/mt7530.h +@@ -741,10 +741,10 @@ struct mt753x_info { + * registers + * @p6_interface Holding the current port 6 interface + * @p5_intf_sel: Holding the current port 5 interface select +- * + * @irq: IRQ number of the switch + * @irq_domain: IRQ domain of the switch irq_chip + * @irq_enable: IRQ enable bits, synced to SYS_INT_EN ++ * @create_sgmii: Pointer to function creating SGMII PCS instance(s) + */ + struct mt7530_priv { + struct device *dev; +@@ -763,7 +763,6 @@ struct mt7530_priv { + unsigned int p5_intf_sel; + u8 mirror_rx; + u8 mirror_tx; +- + struct mt7530_port ports[MT7530_NUM_PORTS]; + struct mt753x_pcs pcs[MT7530_NUM_PORTS]; + /* protect among processes for registers access*/ +@@ -771,6 +770,7 @@ struct mt7530_priv { + int irq; + struct irq_domain *irq_domain; + u32 irq_enable; ++ int (*create_sgmii)(struct mt7530_priv *priv, bool dual_sgmii); + }; + + struct mt7530_hw_vlan_entry { diff --git a/target/linux/generic/backport-6.1/791-v6.2-01-net-phy-Add-driver-for-Motorcomm-yt8521-gigabit-ethernet.patch b/target/linux/generic/backport-6.1/791-v6.2-01-net-phy-Add-driver-for-Motorcomm-yt8521-gigabit-ethernet.patch index df2f65d433..ddb32385e4 100644 --- a/target/linux/generic/backport-6.1/791-v6.2-01-net-phy-Add-driver-for-Motorcomm-yt8521-gigabit-ethernet.patch +++ b/target/linux/generic/backport-6.1/791-v6.2-01-net-phy-Add-driver-for-Motorcomm-yt8521-gigabit-ethernet.patch @@ -21,7 +21,7 @@ Signed-off-by: David S. Miller --- a/MAINTAINERS +++ b/MAINTAINERS -@@ -13959,6 +13959,7 @@ F: include/uapi/linux/meye.h +@@ -13962,6 +13962,7 @@ F: include/uapi/linux/meye.h MOTORCOMM PHY DRIVER M: Peter Geis diff --git a/target/linux/generic/pending-6.1/723-net-mt7531-ensure-all-MACs-are-powered-down-before-r.patch b/target/linux/generic/pending-6.1/723-net-mt7531-ensure-all-MACs-are-powered-down-before-r.patch index 06642ec866..00a43e3e55 100644 --- a/target/linux/generic/pending-6.1/723-net-mt7531-ensure-all-MACs-are-powered-down-before-r.patch +++ b/target/linux/generic/pending-6.1/723-net-mt7531-ensure-all-MACs-are-powered-down-before-r.patch @@ -15,7 +15,7 @@ Signed-off-by: Alexander Couzens --- a/drivers/net/dsa/mt7530.c +++ b/drivers/net/dsa/mt7530.c -@@ -2196,6 +2196,10 @@ mt7530_setup(struct dsa_switch *ds) +@@ -2236,6 +2236,10 @@ mt7530_setup(struct dsa_switch *ds) return -ENODEV; } diff --git a/target/linux/generic/pending-6.1/795-mt7530-register-OF-node-for-internal-MDIO-bus.patch b/target/linux/generic/pending-6.1/795-mt7530-register-OF-node-for-internal-MDIO-bus.patch index 0e0af2a718..26f40d9f87 100644 --- a/target/linux/generic/pending-6.1/795-mt7530-register-OF-node-for-internal-MDIO-bus.patch +++ b/target/linux/generic/pending-6.1/795-mt7530-register-OF-node-for-internal-MDIO-bus.patch @@ -16,7 +16,7 @@ Signed-off-by: David Bauer --- a/drivers/net/dsa/mt7530.c +++ b/drivers/net/dsa/mt7530.c -@@ -2086,10 +2086,13 @@ mt7530_setup_mdio(struct mt7530_priv *pr +@@ -2126,10 +2126,13 @@ mt7530_setup_mdio(struct mt7530_priv *pr { struct dsa_switch *ds = priv->ds; struct device *dev = priv->dev; @@ -30,7 +30,7 @@ Signed-off-by: David Bauer bus = devm_mdiobus_alloc(dev); if (!bus) return -ENOMEM; -@@ -2106,7 +2109,9 @@ mt7530_setup_mdio(struct mt7530_priv *pr +@@ -2146,7 +2149,9 @@ mt7530_setup_mdio(struct mt7530_priv *pr if (priv->irq) mt7530_setup_mdio_irq(priv); -- 2.30.2