From f948f71300a9f9685a6bbb7dfd742ed64892a86c Mon Sep 17 00:00:00 2001 From: Robert Senderek Date: Fri, 10 Oct 2025 14:40:21 +0200 Subject: [PATCH] qualcommax: ipq50xx: Add support for Zyxel SCR50AXE This is tri-band WiFi6E capable router. Also Zyxel Nebula managed so no real local GUI. To open device 4 screws must be located uder the label. Four latches are on front and two on each side. Better start from ethernet port side where 3 small latches are easy to handle. FCC shows It's identical to WSQ65 sold as Zyxel Multy M6E but that's nowhare to be found yet. WSQ65 is not covered by this PR Speficiations: * SoC: Qualcomm IPQ5018 * RAM: 1GB DDR3 * Flash: Winbond W25N02KWZEIR 256MB * UART: PCB "J3" is located left from front LED strip (VCC/TX/RX/ /GND) 3.3V 115200n8 * Wi-Fi1: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax) * Wi-Fi2: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax) * Wi-Fi3: QCN6122 (2x2:2 6 Ghz 802.11an/ac/ax) * Ethernet: QCA8337 4xLAN 1Gbit / 1xWAN 1Gbit * Buttons: WPS , Reset * LEDs: 13 in total RGB power, RGB wan, RGB status (cloud), RGB wifi, Green wps * FCCID: I8803891 *Flash Instructions starts with getting root: connect uart to J3 connector next to the front LEDs go to failsafe when this shows up in log: "Press the [f] key and hit [enter] to enter failsafe mode" execute: mount_root passwd -d root reboot logon as root: look for 'Please press Enter to activate this console.' login is root password is empty execute: fw_setenv DebugFlag=0x1 fw_setenv bootdelay=0x2 passwd -d root backup ubi partition "rootfs" into safe space reboot *OpenWrt installation stop uboot and execute: setenv ipaddr 192.168.1.1 setenv serverip 192.168.1.10 tftpboot *-factory.ubi flash rootfs reset or: tftpboot *-initramfs-uImage.itb bootm use sysupgrade as usual *restore OEM from backup stop uboot and execute: setenv ipaddr 192.168.1.1 setenv serverip 192.168.1.10 tftpboot *-initramfs-uImage.itb bootm transfer rootfs.bin backup and execute: ubiformat /dev/mtd16 -y -f /tmp/rootfs.bin Signed-off-by: Robert Senderek Link: https://github.com/openwrt/openwrt/pull/21042 Signed-off-by: Robert Marko --- .../uboot-envtools/files/qualcommax_ipq50xx | 3 +- package/firmware/ipq-wifi/Makefile | 4 +- .../arm64/boot/dts/qcom/ipq5018-scr50axe.dts | 426 ++++++++++++++++++ target/linux/qualcommax/image/ipq50xx.mk | 15 + .../ipq50xx/base-files/etc/board.d/02_network | 3 +- .../etc/hotplug.d/firmware/11-ath11k-caldata | 11 +- .../base-files/lib/upgrade/platform.sh | 3 +- 7 files changed, 459 insertions(+), 6 deletions(-) create mode 100644 target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq5018-scr50axe.dts diff --git a/package/boot/uboot-tools/uboot-envtools/files/qualcommax_ipq50xx b/package/boot/uboot-tools/uboot-envtools/files/qualcommax_ipq50xx index d8542a9aac..6366859fc3 100644 --- a/package/boot/uboot-tools/uboot-envtools/files/qualcommax_ipq50xx +++ b/package/boot/uboot-tools/uboot-envtools/files/qualcommax_ipq50xx @@ -10,7 +10,8 @@ board=$(board_name) case "$board" in cmcc,pz-l8|\ elecom,wrc-x3000gs2|\ -iodata,wn-dax3000gr) +iodata,wn-dax3000gr|\ +zyxel,scr50axe) ubootenv_add_mtd "0:appsblenv" "0x0" "0x40000" "0x20000" ;; glinet,gl-b3000) diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 36370bb0d0..2f602f082b 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -106,7 +106,8 @@ ALLWIFIBOARDS:= \ zte_mf287 \ zte_mf287plus \ zyxel_nbg7815 \ - zyxel_nwa210ax + zyxel_nwa210ax \ + zyxel_scr50axe ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD)) @@ -289,5 +290,6 @@ $(eval $(call generate-ipq-wifi-package,zte_mf287,ZTE MF287)) $(eval $(call generate-ipq-wifi-package,zte_mf287plus,ZTE MF287Plus)) $(eval $(call generate-ipq-wifi-package,zyxel_nbg7815,Zyxel NBG7815)) $(eval $(call generate-ipq-wifi-package,zyxel_nwa210ax,Zyxel NWA210AX)) +$(eval $(call generate-ipq-wifi-package,zyxel_scr50axe,Zyxel SCR50AXE)) $(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE)))) diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq5018-scr50axe.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq5018-scr50axe.dts new file mode 100644 index 0000000000..fd625af414 --- /dev/null +++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq5018-scr50axe.dts @@ -0,0 +1,426 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; + +#include "ipq5018.dtsi" +#include "ipq5018-ess.dtsi" +#include "ipq5018-qcn6122.dtsi" + +#include +#include +#include + +/ { + model = "Zyxel SCR50AXE"; + compatible ="zyxel,scr50axe", "qcom,ipq5018"; + + aliases { + label-mac-device = &dp2; + led-boot = &led_power_blue; + led-failsafe = &led_power_red; + led-upgrade = &led_power_green; + led-running = &led_power_green; + serial0 = &blsp1_uart1; + }; + + chosen { + bootargs-append = " root=/dev/ubiblock0_1 swiotlb=1 coherent_pool=2M"; + stdout-path = "serial0:115200n8"; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + reset { + label = "reset"; + gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&leds_pins>; + pinctrl-names = "default"; + + led_power_red: R1 { + color = ; + function = LED_FUNCTION_POWER; + gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>; + }; + + led_power_green: G1 { + color = ; + function = LED_FUNCTION_POWER; + gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>; + }; + + led_power_blue: B1 { + color = ; + function = LED_FUNCTION_POWER; + gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>; + }; + + R2 { + color = ; + function = LED_FUNCTION_WAN; + gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>; + }; + + G2 { + color = ; + function = LED_FUNCTION_WAN; + gpios = <&tlmm 35 GPIO_ACTIVE_HIGH>; + }; + + B2 { + color = ; + function = LED_FUNCTION_WAN; + gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>; + }; + + R3 { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>; + }; + + G3 { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&tlmm 34 GPIO_ACTIVE_HIGH>; + }; + + B3 { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>; + }; + + R4 { + color = ; + function = LED_FUNCTION_WLAN_6GHZ; + gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy2radio"; + }; + + G4 { + color = ; + function = LED_FUNCTION_WLAN_2GHZ; + gpios = <&tlmm 33 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0radio"; + }; + + B4 { + color = ; + function = LED_FUNCTION_WLAN_5GHZ; + gpios = <&tlmm 30 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy1radio"; + }; + + G5 { + color = ; + function = LED_FUNCTION_WPS; + gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&switch { + status = "okay"; + switch_mac_mode = ; + + qcom,port_phyinfo { + + port@0 { + port_id = <1>; + mdiobus = <&mdio0>; + phy_address = <7>; + }; + + port@1 { + port_id = <2>; + forced-speed = <1000>; + forced-duplex = <1>; + }; + }; +}; + +&dp1 { + status = "okay"; + + label = "wan"; + nvmem-cells = <&macaddr_appsblenv_ethaddr 0>; + nvmem-cell-names = "mac-address"; +}; + +&dp2 { + status = "okay"; + nvmem-cells = <&macaddr_appsblenv_ethaddr (-4)>; + nvmem-cell-names = "mac-address"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&mdio0 { + status = "okay"; +}; + +&mdio1 { + status = "okay"; + pinctrl-0 = <&mdio1_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 39 GPIO_ACTIVE_LOW>; + + qca8337_0: ethernet-phy@0 { + reg = <0>; + }; + + qca8337_1: ethernet-phy@1 { + reg = <1>; + }; + + qca8337_2: ethernet-phy@2 { + reg = <2>; + }; + + qca8337_3: ethernet-phy@3 { + reg = <3>; + }; + + ethernet-switch@17 { + compatible = "qca,qca8337"; + reg = <0x17>; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&qca8337_0>; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&qca8337_1>; + }; + + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&qca8337_2>; + }; + + port@4 { + reg = <4>; + label = "lan4"; + phy-handle = <&qca8337_3>; + }; + + port@6 { + reg = <6>; + phy-mode = "sgmii"; + ethernet = <&dp2>; + qca,sgmii-enable-pll; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; +}; + +&sleep_clk { + clock-frequency = <32000>; +}; + +&xo_board_clk { + clock-div = <4>; + clock-mult = <1>; +}; + +&blsp1_uart1 { + status = "okay"; + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; +}; + +&crypto { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&prng { + status = "okay"; +}; + +&qfprom { + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&qpic_nand { + pinctrl-0 = <&qpic_pins>; + pinctrl-names = "default"; + status = "okay"; + + nand@0 { + compatible = "spi-nand"; + reg = <0>; + nand-ecc-engine = <&qpic_nand>; + nand-bus-width = <8>; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "qcom,smem-part"; + + partition-0-appsblenv { + compatible = "fixed-partitions"; + label = "0:appsblenv"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "env-data"; + reg = <0x0 0x40000>; + + nvmem-layout { + compatible = "u-boot,env"; + + macaddr_appsblenv_ethaddr: ethaddr { + compatible = "mac-base"; + #nvmem-cell-cells = <1>; + }; + }; + }; + }; + }; + }; +}; + +&tlmm { + mdio1_pins: mdio-state { + mdc-pins { + pins = "gpio36"; + function = "mdc"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio-pins { + pins = "gpio37"; + function = "mdio"; + drive-strength = <8>; + bias-pull-up; + }; + }; + + leds_pins: leds-pins { + pins = "gpio26", "gpio35", "gpio32", "gpio25", "gpio34", + "gpio24", "gpio31", "gpio33", "gpio30", "gpio10", + "gpio11", "gpio12", "gpio40"; + function = "gpio"; + drive-strength = <8>; + bias-pull-down; + }; + + button_pins: button-pins { + pins = "gpio22", "gpio38"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + + qpic_pins: qpic-state { + clock-pins { + pins = "gpio9"; + function = "qspi_clk"; + drive-strength = <8>; + bias-disable; + }; + + cs-pins { + pins = "gpio8"; + function = "qspi_cs"; + drive-strength = <8>; + bias-disable; + }; + + data-pins { + pins = "gpio4", "gpio5", "gpio6", "gpio7"; + function = "qspi_data"; + drive-strength = <8>; + bias-disable; + }; + }; + + serial_0_pins: uart0-state { + pins = + "gpio20", // RX + "gpio21"; // TX + function = "blsp0_uart0"; + drive-strength = <8>; + bias-disable; + }; +}; + +&q6_region { + reg = <0x0 0x4b000000 0x0 0x4d00000>; +}; + +&wifi { + status = "okay"; + + qcom,rproc = <&q6_wcss_pd1>; + qcom,userpd-subsys-name = "q6v5_wcss_userpd1"; + qcom,ath11k-calibration-variant = "Zyxel-SCR50AXE"; + qcom,ath11k-fw-memory-mode = <1>; + qcom,bdf-addr = <0x4c400000>; +}; + +&wifi1 { + status = "okay"; + + qcom,rproc = <&q6_wcss_pd2>; + qcom,userpd-subsys-name = "q6v5_wcss_userpd2"; + qcom,ath11k-calibration-variant = "Zyxel-SCR50AXE-5G"; + qcom,ath11k-fw-memory-mode = <1>; + qcom,bdf-addr = <0x4d100000>; + qcom,m3-dump-addr = <0x4df00000>; +}; + +&wifi2 { + status = "okay"; + + qcom,rproc = <&q6_wcss_pd3>; + qcom,userpd-subsys-name = "q6v5_wcss_userpd3"; + qcom,ath11k-calibration-variant = "Zyxel-SCR50AXE-6G"; + qcom,ath11k-fw-memory-mode = <1>; + qcom,bdf-addr = <0x4e500000>; + qcom,m3-dump-addr = <0x4f200000>; +}; diff --git a/target/linux/qualcommax/image/ipq50xx.mk b/target/linux/qualcommax/image/ipq50xx.mk index be247c7df9..7fab522783 100644 --- a/target/linux/qualcommax/image/ipq50xx.mk +++ b/target/linux/qualcommax/image/ipq50xx.mk @@ -218,3 +218,18 @@ define Device/yuncore_ax850 ipq-wifi-yuncore_ax850 endef TARGET_DEVICES += yuncore_ax850 + +define Device/zyxel_scr50axe + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_VENDOR := Zyxel + DEVICE_MODEL := SCR50AXE + SOC := ipq5018 + BLOCKSIZE := 128k + PAGESIZE := 2048 + NAND_SIZE := 256m + DEVICE_DTS_CONFIG := config@mp03.5-c1 + DEVICE_PACKAGES := ath11k-firmware-ipq5018-qcn6122 \ + ipq-wifi-zyxel_scr50axe +endef +TARGET_DEVICES += zyxel_scr50axe diff --git a/target/linux/qualcommax/ipq50xx/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq50xx/base-files/etc/board.d/02_network index 4bcd7dd5df..09a68d7c1e 100644 --- a/target/linux/qualcommax/ipq50xx/base-files/etc/board.d/02_network +++ b/target/linux/qualcommax/ipq50xx/base-files/etc/board.d/02_network @@ -9,7 +9,8 @@ ipq50xx_setup_interfaces() case $board in elecom,wrc-x3000gs2|\ iodata,wn-dax3000gr|\ - linksys,mr5500) + linksys,mr5500|\ + zyxel,scr50axe) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan" ;; glinet,gl-b3000) diff --git a/target/linux/qualcommax/ipq50xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/qualcommax/ipq50xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata index cf48022aea..d4a913b9cc 100644 --- a/target/linux/qualcommax/ipq50xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata +++ b/target/linux/qualcommax/ipq50xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata @@ -10,7 +10,8 @@ case "$FIRMWARE" in "ath11k/IPQ5018/hw1.0/cal-ahb-c000000.wifi.bin") case "$board" in elecom,wrc-x3000gs2|\ - iodata,wn-dax3000gr) + iodata,wn-dax3000gr|\ + zyxel,scr50axe) caldata_extract "0:art" 0x1000 0x20000 wlan_mac=$(mtd_get_mac_ascii 0:appsblenv wifi0) ath11k_patch_mac $wlan_mac 0 @@ -54,7 +55,8 @@ case "$FIRMWARE" in "ath11k/QCN6122/hw1.0/cal-ahb-b00a040.wifi.bin") case "$board" in elecom,wrc-x3000gs2|\ - iodata,wn-dax3000gr) + iodata,wn-dax3000gr|\ + zyxel,scr50axe) caldata_extract "0:art" 0x26800 0x20000 wlan_mac=$(mtd_get_mac_ascii 0:appsblenv wifi1) ath11k_patch_mac $wlan_mac 0 @@ -95,6 +97,11 @@ case "$FIRMWARE" in label_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr) ath11k_patch_mac $(macaddr_add $label_mac 4) 0 ath11k_remove_regdomain + ;; + zyxel,scr50axe) + caldata_extract "0:art" 0x4C000 0x20000 + wlan_mac=$(mtd_get_mac_ascii 0:appsblenv wifi2) + ath11k_patch_mac $wlan_mac 0 ath11k_set_macflag ;; esac diff --git a/target/linux/qualcommax/ipq50xx/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq50xx/base-files/lib/upgrade/platform.sh index 24bacdb6b8..c6e8d0fb0d 100644 --- a/target/linux/qualcommax/ipq50xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/qualcommax/ipq50xx/base-files/lib/upgrade/platform.sh @@ -229,7 +229,8 @@ platform_do_upgrade() { nand_do_upgrade "$1" ;; yuncore,ax830|\ - yuncore,ax850) + yuncore,ax850|\ + zyxel,scr50axe) CI_UBIPART="rootfs" remove_oem_ubi_volume ubi_rootfs remove_oem_ubi_volume bt_fw -- 2.30.2