ar71xx: drop target This target has been mostly replaced by ath79 and won't be included in the upcoming release anymore. Finally put it to rest. This also removes all references in packages, tools, etc. as well as the uboot-ar71xx and vsc73x5-ucode packages. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ar71xx/mikrotik: ath10k: use new sysfs driver Fetch ath10k calibration data from new mikrotik sysfs driver Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
ar71xx: fix swapped LAN/WAN MAC address for Archer C60 v1/v2 The MAC addresses for lan/wan are swapped compared to the vendor firmware. This adjusts to vendor configuration, which is: lan *:7b label wan *:7c label+1 2.4g *:7b label 5g *:7a label-1 Only one address is stored in <&mac 0x8>, corresponding to the label. This has been checked on revisions v1, v2 and v3. Since ar71xx calculates the ath10k MAC address based on the ethernet addresses, the number there is adjusted, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ar71xx: fix MAC addresses for Archer C5 v1, C7 v1/v2, WDR4900 v2 As discussed in 1d18a14a90c7 ("ath79: really fix TP-Link Archer C7 v2 MAC address"), stock firmware MAC address assignment is actually as follows: wlan0 (5GHz) : -1 wlan1 (2.4GHz) : 0 eth1 (LAN) : 0 eth0 (WAN) : 1 This has never been fixed for ar71xx, so let's do it now. Note that with WDR4900 v2 even both wlan0 and wlan1 where assigned to basemac-1 before ... Fixes: FS#408 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
treewide: convert WiFi caldata size and offset to hexadecimal This changes size and offset set for WiFi caldata extraction and MAC address adjustment to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-cal-data in DTS files. Since dd cannot deal with hexadecimal notation, one has to convert back to decimal by simple $(($hexnum)). Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
treewide: convert MAC address location offsets to hexadecimal This changes the offsets for the MAC address location in mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-mac-address in DTS files. (e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486) Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ar71xx: add support for MikroTik RouterBOARD 922UAGS-5HPacD This patch adds support for the MikroTik RouterBOARD 922UAGS-5HPacD with a built-in 802.11ac High-Power radio (31dBm). See https://mikrotik.com/product/RB922UAGS-5HPacD for more info. Specifications: - SoC: Qualcomm Atheros QCA9557 (720 MHz) - RAM: 128 MB - Storage: 128 MB NAND - Wireless: external QCA9882 802.11a/ac 2x2:2 - Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE-in 24V - SFP: 1x host - USB: 1x 2.0 type A - PCIe: 1x Mini slot (also contains USB 2.0 for 3G/LTE modems) - SIM slot: 1x mini-SIM Working: - Board/system detection - NAND storage detection - PCIe - USB: Type A & mini PCIe - Wireless - Ethernet - LED's (excl. SFP and RSSI levels) - Reset button - Sysupgrade Not working: - SFP cage Installation: - Boot vmlinux-initramfs image via BOOTP/TFTP and then flash sysupgrade image using "sysupgrade -n" Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
ar71xx: Speed up caldata/eeprom handling Reading and writing to and from flash storage is slowed down enormously by some functions which use a block size of 1. This patch reworks the extraction scripts to be much faster and efficient by reading and writing in possibly one big block. This is based on the initial commit a69e101 for ipq40xx by Christian Lamparter <chunkeey@gmail.com>. Speed comparison @ TP-Link TL-WDR4300 (just manually) results in a time reduction by three orders of magnitude (99.9 %). > time dd if=/dev/mtd3 of=/lib/firmware/test-slow bs=1 count=4096 skip=4096 4096+0 records in 4096+0 records out real 0m 15.85s user 0m 0.06s sys 0m 13.28s > time dd if=/dev/mtd3 of=/lib/firmware/test-fast bs=4096 count=1 skip=4096 iflag=skip_bytes 1+0 records in 1+0 records out real 0m 0.02s user 0m 0.00s sys 0m 0.02s Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ar71xx: Fix 5 GHz MAC address for Archer C60 v2 Looks like C60 v2 needs the MAC address to be calculated manually, while the C60 v1 gets it correctly without manual interference. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ar71xx: add support for Gainstrong MiniBox V3.2 Adds MiniBox V3.2 ar71xx target (QCA99531 + QCA9887) Info: http://oolite.cn/minibox-v3-2-qca9531-qca9887-module-pin-specification.html Reference patch: http://oolite.cn/wp-content/uploads/2017/09/minibox_v3_cc15.05_20160325.patch Installation: Upload firmware to uboot via HTTP at 192.168.1.1 (press button for 5 seconds) Signed-off-by: Pau Escrich <p4u@dabax.net> Signed-off-by: Daniel Golle <daniel@makrotopia.org> (daniel@makrotopia.org: rebased and fixed conflicts, fixed LED name, added ath10k eeprom)
ar71xx: add support for TP-Link Archer C59 v2 TP-Link Archer C59v2 is a dual-band AC1350 router based on Qualcomm/Atheros QCA9561+QCA9886 chips. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - UART header on PCB Flash instruction: - via web UI: 1. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin 2. Login to router and open the Advanced tab 3. Navigate to System Tools -> Firmware Upgrade 4. Upload firmware using the Manual Upgrade form - via TFTP: 1. Set PC to fixed ip address 192.168.0.66 2. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Keith Maika <keithm@aoeex.com>
ar71xx: add support for TP-LINK Archer C7 v5 TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros QCA9563+QCA9880. Specification: - 750/400/250 MHz (CPU/DDR/AHB - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 5x 10/100/1000 Mbps Ethernet - 10x LED, 2x button - UART header on PCB Flash instruction: 1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface Flash instruction using TFTP recovery: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin and rename it to ArcherC7v5_tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Arvid E. Picciani <aep@exys.org>
ar71xx: add support for OCEDO Koala This commit adds support for the OCEDO Koala SOC: Qualcomm QCA9558 (Scorpion) RAM: 128MB FLASH: 16MiB WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3 WLAN2: QCA9880 5 GHz 802.11nac 3x3 INPUT: RESET button LED: Power, LAN, WiFi 2.4, WiFi 5, SYS Serial: Header Next to Black metal shield Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi - 5 GHz WiFi - TFTP boot from ramdisk image - Installation via ramdisk image - OpenWRT sysupgrade - Buttons - LEDs Installation seems to be possible only through booting an OpenWRT ramdisk image. Hold down the reset button while powering on the device. It will load a ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8. Note: depending on the present software, the device might also try to pull a file called 'koala-uimage-factory'. Only the name differs, it is still used as a ramdisk image. Wait for the ramdisk image to boot. OpenWRT can be written to the flash via sysupgrade or mtd. Due to the flip-flop bootloader which we not (yet) support, you need to set the partition the bootloader is selecting. It is possible from the initramfs image with > fw_setenv bootcmd run bootcmd_1 Afterwards you can reboot the device. Signed-off-by: David Bauer <mail@david-bauer.net>
ar71xx: add support for GL.iNet GL-AR750S This patch adds supports for GL-AR750S. Specification: - SOC: QCA9563 (775MHz) - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR2 - Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN - Wireless: 2.4GHz (bgn) and 5GHz (ac) - USB: 1x USB 2.0 port - Button: 1x switch button, 1x reset button - LED: 3x LEDS (green) Flash instruction: Apply factory image via web-gui. Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
ar71xx: add support for TP-Link Archer C60 v2 TP-Link Archer C60 v2 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561 + QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction (web): Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and use OEM System Tools - Firmware Upgrade site. Flash instruction (recovery): 1. Set PC to fixed IP address 192.168.0.66 2. Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery Flash instruction (under U-Boot, using UART): tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin erase 0x9f030000 +$filesize cp.b $fileaddr 0x9f030000 $filesize reset Signed-off-by: Henryk Heisig <hyniu@o2.pl>
ar71xx: add support for GainStrong Oolite V5.2 GainStrong Oolite V5.2 is a small (39.5 x 78 mm), dual-band system on module, based on Qualcomm QCA9531 + QCA9887. All QCA9531 SOC GPIOs are available on castellated pins. Specification: - 650/400/200 MHz (CPU/DDR/AHB) - 64/128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 5x 10/100 Mbps Ethernet (all ports available on castellated pins) - 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA - 1T1R 5 GHz (QCA9887) with ext. FEM (SKY85710-11) - 3x U.FL - 1x USB 2.0 The dedicated development board includes 5 FE ports, USB 2.0 port, two buttons (one directly connected to SOC reset input), header with all GPIOs and several LEDs. Flash instruction: Vendor firmware is based on OpenWrt. LuCI or sysupgrade can be used to flash OpenWrt firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ar71xx: fix 5 GHz Wi-Fi on NBG6716 Some NBG6716 do not have ath10k calibration data in flash, only in chip OTP. To determine if flash has a valid calibration data, the first two bytes telling the length of the calibration data are checked against the requested length. If the lengths match, calibration data is valid and read from flash. Signed-off-by: Matti Laakso <matti.laakso@outlook.com>
ar71xx: add support for COMFAST CF-E385AC COMFAST CF-E385AC is an AC2200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9558 + QCA9984 + QCA8337N. Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 256 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100/1000 Mbps Ethernet, with PoE support - 3T3R 2.4 GHz (QCA9558), with external LNA and PA (SE2576L) - 4T4R 5 GHz (QCA9984), with external FEM (SKY85728-11) - 7x internal antennas - 1x RGB LED (driven by GPIO) - 1x button (reset) - UART, LEDs/GPIO and USB headers on PCB - external watchdog (Pericon Technology PT7A7514) Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ar71xx: rename COMFAST CF-E355AC to CF-E355AC v1 There are now supported two versions of the CF-E355AC board which differ in 802.11ac radio chip. Include version number in board, model, image filename, etc., also for the v1. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ar71xx: add support for COMFAST CF-E355AC v2 COMFAST CF-E355AC v2 is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9531 + QCA9886. Short specification: - 2x 10/100 Mbps Ethernet, with PoE support - 128MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, 802.11b/g/n - 2T2R 5 GHz, 802.11ac/n/a, WAVE 2 - built-in 4x 3 dBi antennas - output power (max): 500 mW (27 dBm) - 1x RGB LED, 1x button - built-in watchdog chipset Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Ding Tengfei <dtf@comfast.cn> [updated kernel config for both boards] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>