ath79: enable UART in SoC DTSI files
[openwrt/openwrt.git] / target / linux / ath79 / dts / ar7240_tplink.dtsi
1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2
3 #include "ar7240.dtsi"
4
5 #include <dt-bindings/gpio/gpio.h>
6 #include <dt-bindings/input/input.h>
7
8 / {
9 aliases {
10 led-boot = &led_system;
11 led-failsafe = &led_system;
12 led-running = &led_system;
13 led-upgrade = &led_system;
14 label-mac-device = &ath9k;
15 };
16
17 keys {
18 compatible = "gpio-keys";
19
20 reset {
21 label = "reset";
22 linux,code = <KEY_RESTART>;
23 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
24 debounce-interval = <60>;
25 };
26
27 wps {
28 label = "wps";
29 linux,code = <KEY_WPS_BUTTON>;
30 gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
31 debounce-interval = <60>;
32 };
33 };
34
35 leds: leds {
36 compatible = "gpio-leds";
37
38 pinctrl-names = "default";
39 pinctrl-0 = <&pinmux_switch_led_pins>;
40
41 led_system: system {
42 label = "green:system";
43 gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
44 };
45
46 qss {
47 label = "green:qss";
48 gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
49 };
50 };
51
52 ath9k-leds {
53 compatible = "gpio-leds";
54
55 wlan {
56 label = "green:wlan";
57 gpios = <&ath9k 1 GPIO_ACTIVE_LOW>;
58 linux,default-trigger = "phy0tpt";
59 };
60 };
61 };
62
63 &spi {
64 status = "okay";
65
66 flash@0 {
67 compatible = "jedec,spi-nor";
68 reg = <0>;
69 spi-max-frequency = <25000000>;
70
71 partitions {
72 compatible = "fixed-partitions";
73 #address-cells = <1>;
74 #size-cells = <1>;
75
76 uboot: partition@0 {
77 reg = <0x0 0x20000>;
78 label = "u-boot";
79 read-only;
80 };
81
82 partition@20000 {
83 compatible = "tplink,firmware";
84 reg = <0x20000 0x3d0000>;
85 label = "firmware";
86 };
87
88 art: partition@3f0000 {
89 reg = <0x3f0000 0x10000>;
90 label = "art";
91 read-only;
92 };
93 };
94 };
95 };
96
97 &eth1 {
98 status = "okay";
99 };
100
101 &pcie {
102 status = "okay";
103
104 ath9k: wifi@0,0 {
105 reg = <0x0000 0 0 0 0>;
106 qca,no-eeprom;
107 mtd-mac-address = <&uboot 0x1fc00>;
108 #gpio-cells = <2>;
109 gpio-controller;
110 };
111 };
112
113 &pinmux {
114 pinmux_switch_led_pins: switch_led_pins {
115 pinctrl-single,bits = <0x0 0x0 0xf8>;
116 };
117 };