target/linux/ath79/dts/ar9330_glinet_ar150.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar9330.dtsi"
   8
   9 / {
  10         model = "GL.iNet GL-AR150";
  11         compatible = "glinet,ar150", "qca,ar9330";
  12
  13         aliases {
  14                 serial0 = &uart;
  15                 led-status = &wlan;
  16         };
  17
  18         leds {
  19                 compatible = "gpio-leds";
  20
  21                 wlan: wlan {
  22                         label = "gl-ar150:orange:wlan";
  23                         gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
  24                         default-state = "off";
  25                         linux,default-trigger = "phy0tpt";
  26                 };
  27
  28                 lan {
  29                         label = "gl-ar150:green:lan";
  30                         gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
  31                         default-state = "off";
  32                 };
  33
  34                 wan {
  35                         label = "gl-ar150:green:wan";
  36                         gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
  37                         default-state = "off";
  38                 };
  39         };
  40
  41         keys {
  42                 compatible = "gpio-keys-polled";
  43                 #address-cells = <1>;
  44                 #size-cells = <0>;
  45                 poll-interval = <100>;
  46
  47                 manual {
  48                         label = "manual";
  49                         linux,code = <BTN_7>;
  50                         gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
  51                 };
  52
  53                 auto {
  54                         label = "auto";
  55                         linux,code = <BTN_8>;
  56                         gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
  57                 };
  58
  59                 reset {
  60                         label = "reset";
  61                         linux,code = <KEY_RESTART>;
  62                         gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
  63                 };
  64         };
  65 };
  66
  67 &uart {
  68         status = "okay";
  69 };
  70
  71 &gpio {
  72         status = "okay";
  73 };
  74
  75 &usb {
  76         dr_mode = "host";
  77         status = "okay";
  78 };
  79
  80 &usb_phy {
  81         status = "okay";
  82         gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
  83 };
  84
  85 &spi {
  86         num-chipselects = <1>;
  87         status = "okay";
  88
  89         spiflash@0 {
  90                 #address-cells = <1>;
  91                 #size-cells = <1>;
  92                 compatible = "jedec,spi-nor";
  93                 spi-max-frequency = <104000000>;
  94                 reg = <0>;
  95
  96                 partitions {
  97                         compatible = "fixed-partitions";
  98                         #address-cells = <1>;
  99                         #size-cells = <1>;
 100
 101                         partition@0 {
 102                                 label = "u-boot";
 103                                 reg = <0x000000 0x040000>;
 104                                 read-only;
 105                         };
 106
 107                         partition@1 {
 108                                 label = "u-boot-env";
 109                                 reg = <0x040000 0x010000>;
 110                         };
 111
 112                         partition@2 {
 113                                 label = "firmware";
 114                                 reg = <0x050000 0xfa0000>;
 115                         };
 116
 117                         art: partition@3 {
 118                                 label = "ART";
 119                                 reg = <0xff0000 0x010000>;
 120                                 read-only;
 121                         };
 122                 };
 123         };
 124 };
 125
 126 &mdio0 {
 127         status = "okay";
 128
 129         phy4: ethernet-phy@4 {
 130                 reg = <4>;
 131                 phy-mode = "mii";
 132         };
 133 };
 134
 135 &eth0 {
 136         status = "okay";
 137
 138         mtd-mac-address = <&art 0x0>;
 139
 140         phy-handle = <&phy4>;
 141 };
 142
 143 &eth1 {
 144         status = "okay";
 145
 146         mtd-mac-address = <&art 0x0>;
 147
 148         fixed-link {
 149                 speed = <1000>;
 150                 full-duplex;
 151         };
 152
 153         gmac-config {
 154                 device = <&gmac>;
 155
 156                 switch-phy-addr-swap = <0>;
 157                 switch-phy-swap = <0>;
 158         };
 159 };
 160
 161 &wmac {
 162         status = "okay";
 163         mtd-cal-data = <&art 0x1000>;
 164         mtd-mac-address = <&art 0x0>;
 165 };