ath79: etactica-eg200: fix restore button
[openwrt/openwrt.git] / target / linux / ath79 / dts / ar9331_etactica_eg200.dts
1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2 /dts-v1/;
3
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6
7 #include "ar9331.dtsi"
8
9 / {
10 model = "eTactica EG200";
11 compatible = "etactica,eg200", "qca,ar9331";
12
13 aliases {
14 serial0 = &uart;
15 };
16
17 keys {
18 compatible = "gpio-keys-polled";
19 poll-interval = <50>;
20
21 restore {
22 linux,code = <KEY_RESTART>;
23 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
24 };
25 };
26
27 leds {
28 compatible = "gpio-leds";
29 pinctrl-names = "default";
30 pinctrl-0 = <&switch_led_disable_pins>;
31
32 modbus {
33 label = "eg200:red:modbus";
34 gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
35 };
36
37 etactica {
38 label = "eg200:red:etactica";
39 gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
40 };
41
42 eth0 {
43 label = "eg200:red:eth0";
44 gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
45 };
46
47 wlan {
48 label = "eg200:red:wlan";
49 gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
50 linux,default-trigger = "phy0tpt";
51 };
52 };
53 };
54
55 &uart {
56 status = "okay";
57 };
58
59 &gpio {
60 status = "okay";
61 };
62
63 &usb {
64 dr_mode = "host";
65 status = "okay";
66 };
67
68 &usb_phy {
69 status = "okay";
70 };
71
72 &eth0 {
73 status = "okay";
74 mtd-mac-address = <&art 0x0>;
75
76 gmac-config {
77 device = <&gmac>;
78 switch-phy-addr-swap = <1>;
79 switch-phy-swap = <1>;
80 };
81 };
82
83 &eth1 {
84 status = "okay";
85 compatible = "syscon", "simple-mfd";
86 };
87
88 &spi {
89 num-chipselects = <1>;
90 status = "okay";
91
92 flash@0 {
93 compatible = "jedec,spi-nor";
94 spi-max-frequency = <50000000>;
95 reg = <0>;
96
97 partitions {
98 compatible = "fixed-partitions";
99 #address-cells = <1>;
100 #size-cells = <1>;
101
102 uboot@0 {
103 reg = <0x0 0x40000>;
104 read-only;
105 };
106
107 uboot-env@40000 {
108 reg = <0x40000 0x10000>;
109 read-only;
110 };
111
112 firmware@50000 {
113 compatible = "denx,uimage";
114 reg = <0x50000 0xfa0000>;
115 };
116
117 art: art@ff0000 {
118 reg = <0xff0000 0x10000>;
119 read-only;
120 };
121 };
122 };
123 };
124
125 &wmac {
126 status = "okay";
127 mtd-cal-data = <&art 0x1000>;
128 mtd-mac-address = <&art 0x1002>;
129 };