target/linux/ath79/dts/ar9331_etactica_eg200.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar9331.dtsi"
   8
   9 / {
  10         model = "eTactica EG200";
  11         compatible = "etactica,eg200", "qca,ar9331";
  12
  13         aliases {
  14                 serial0 = &uart;
  15         };
  16
  17         keys {
  18                 compatible = "gpio-keys-polled";
  19                 poll-interval = <50>;
  20
  21                 restore {
  22                         linux,code = <KEY_WPS_BUTTON>;
  23                         gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
  24                 };
  25         };
  26
  27         leds {
  28                 compatible = "gpio-leds";
  29                 pinctrl-names = "default";
  30                 pinctrl-0 = <&switch_led_disable_pins>;
  31
  32                 modbus {
  33                         label = "eg200:red:modbus";
  34                         gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
  35                 };
  36
  37                 etactica {
  38                         label = "eg200:red:etactica";
  39                         gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
  40                 };
  41
  42                 eth0 {
  43                         label = "eg200:red:eth0";
  44                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  45                 };
  46
  47                 wlan {
  48                         label = "eg200:red:wlan";
  49                         gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
  50                         linux,default-trigger = "phy0tpt";
  51                 };
  52         };
  53 };
  54
  55 &uart {
  56         status = "okay";
  57 };
  58
  59 &gpio {
  60         status = "okay";
  61 };
  62
  63 &usb {
  64         dr_mode = "host";
  65         status = "okay";
  66 };
  67
  68 &usb_phy {
  69         status = "okay";
  70 };
  71
  72 &eth0 {
  73         status = "okay";
  74         mtd-mac-address = <&art 0x0>;
  75
  76         gmac-config {
  77                 device = <&gmac>;
  78                 switch-phy-addr-swap = <1>;
  79                 switch-phy-swap = <1>;
  80         };
  81 };
  82
  83 &eth1 {
  84         status = "okay";
  85         compatible = "syscon", "simple-mfd";
  86 };
  87
  88 &spi {
  89         num-chipselects = <1>;
  90         status = "okay";
  91
  92         flash@0 {
  93                 compatible = "jedec,spi-nor";
  94                 spi-max-frequency = <50000000>;
  95                 reg = <0>;
  96
  97                 partitions {
  98                         compatible = "fixed-partitions";
  99                         #address-cells = <1>;
 100                         #size-cells = <1>;
 101
 102                         uboot@0 {
 103                                 reg = <0x0 0x40000>;
 104                                 read-only;
 105                         };
 106
 107                         uboot-env@40000 {
 108                                 reg = <0x40000 0x10000>;
 109                                 read-only;
 110                         };
 111
 112                         firmware@50000 {
 113                                 compatible = "denx,uimage";
 114                                 reg = <0x50000 0xfa0000>;
 115                         };
 116
 117                         art: art@ff0000 {
 118                                 reg = <0xff0000 0x10000>;
 119                                 read-only;
 120                         };
 121                 };
 122         };
 123 };
 124
 125 &wmac {
 126         status = "okay";
 127         mtd-cal-data = <&art 0x1000>;
 128         mtd-mac-address = <&art 0x1002>;
 129 };