ath79: fix dts warnings
[openwrt/openwrt.git] / target / linux / ath79 / dts / ar9331_etactica_eg200.dts
1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2 /dts-v1/;
3
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6
7 #include "ar9331.dtsi"
8
9 / {
10 model = "eTactica EG200";
11 compatible = "etactica,eg200", "rme-eg200";
12
13 aliases {
14 serial0 = &uart;
15 };
16
17 keys {
18 compatible = "gpio-keys-polled";
19 poll-interval = <50>;
20
21 restore {
22 linux,code = <KEY_WPS_BUTTON>;
23 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
24 };
25 };
26
27 leds {
28 compatible = "gpio-leds";
29
30 modbus {
31 label = "eg200:red:modbus";
32 gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
33 default-state = "off";
34 };
35
36 etactica {
37 label = "eg200:red:etactica";
38 gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
39 default-state = "off";
40 };
41
42 eth0 {
43 label = "eg200:red:eth0";
44 gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
45 default-state = "off";
46 };
47
48 wlan {
49 label = "eg200:red:wlan";
50 gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
51 default-state = "off";
52 linux,default-trigger = "phy0tpt";
53 };
54 };
55 };
56
57 &uart {
58 status = "okay";
59 };
60
61 &gpio {
62 status = "okay";
63 };
64
65 &usb {
66 dr_mode = "host";
67 status = "okay";
68 };
69
70 &usb_phy {
71 status = "okay";
72 };
73
74 &eth0 {
75 status = "okay";
76 mtd-mac-address = <&art 0x0>;
77
78 gmac-config {
79 device = <&gmac>;
80 switch-phy-addr-swap = <1>;
81 switch-phy-swap = <1>;
82 };
83 };
84
85 &eth1 {
86 status = "okay";
87 compatible = "syscon", "simple-mfd";
88 };
89
90 &spi {
91 num-chipselects = <1>;
92 status = "okay";
93
94 flash@0 {
95 compatible = "jedec,spi-nor";
96 spi-max-frequency = <50000000>;
97 reg = <0>;
98
99 partitions {
100 compatible = "fixed-partitions";
101 #address-cells = <1>;
102 #size-cells = <1>;
103
104 uboot@0 {
105 reg = <0x0 0x40000>;
106 read-only;
107 };
108
109 uboot-env@40000 {
110 reg = <0x40000 0x10000>;
111 read-only;
112 };
113
114 firmware@50000 {
115 reg = <0x50000 0xfa0000>;
116 };
117
118 art: art@ff0000 {
119 reg = <0xff0000 0x10000>;
120 read-only;
121 };
122 };
123 };
124 };
125
126 &wmac {
127 status = "okay";
128 mtd-cal-data = <&art 0x1000>;
129 mtd-mac-address = <&art 0x1002>;
130 };