target/linux/ath79/dts/ar9331_pisen_ts-d084.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include "ar9331.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         model = "Pisen TS-D084";
  10         compatible = "pisen,ts-d084", "qca,ar9331";
  11
  12         aliases {
  13                 led-boot = &led_system;
  14                 led-failsafe = &led_system;
  15                 led-running = &led_system;
  16                 led-upgrade = &led_system;
  17                 label-mac-device = &wmac;
  18         };
  19
  20         keys {
  21                 compatible = "gpio-keys";
  22
  23                 reset {
  24                         label = "reset";
  25                         linux,code = <KEY_RESTART>;
  26                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  27                         debounce-interval = <60>;
  28                 };
  29         };
  30
  31         leds {
  32                 compatible = "gpio-leds";
  33
  34                 led_system: system {
  35                         label = "blue:system";
  36                         gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
  37                 };
  38         };
  39 };
  40
  41 &spi {
  42         status = "okay";
  43
  44         flash@0 {
  45                 compatible = "jedec,spi-nor";
  46                 reg = <0>;
  47                 spi-max-frequency = <25000000>;
  48
  49                 partitions {
  50                         compatible = "fixed-partitions";
  51                         #address-cells = <1>;
  52                         #size-cells = <1>;
  53
  54                         uboot: partition@0 {
  55                                 reg = <0x0 0x20000>;
  56                                 label = "u-boot";
  57                                 read-only;
  58                         };
  59
  60                         firmware: partition@20000 {
  61                                 compatible = "tplink,firmware";
  62                                 reg = <0x20000 0x7d0000>;
  63                                 label = "firmware";
  64                         };
  65
  66                         art: partition@7f0000 {
  67                                 reg = <0x7f0000 0x10000>;
  68                                 label = "art";
  69                                 read-only;
  70                         };
  71                 };
  72         };
  73 };
  74
  75 &eth0 {
  76         status = "okay";
  77
  78         mtd-mac-address = <&uboot 0x1fc00>;
  79
  80         gmac-config {
  81                 device = <&gmac>;
  82
  83                 switch-phy-addr-swap = <0>;
  84                 switch-phy-swap = <0>;
  85         };
  86 };
  87
  88 &eth1 {
  89         status = "okay";
  90         compatible = "syscon", "simple-mfd";
  91 };
  92
  93 &usb {
  94         dr_mode = "host";
  95         status = "okay";
  96 };
  97
  98 &usb_phy {
  99         status = "okay";
 100 };
 101
 102 &wmac {
 103         status = "okay";
 104         mtd-cal-data = <&art 0x1000>;
 105         mtd-mac-address = <&uboot 0x1fc00>;
 106 };