ath79: add TP-Link TL-MR10U port
[openwrt/openwrt.git] / target / linux / ath79 / dts / ar9331_tl-wr703n.dtsi
1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2 /dts-v1/;
3
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6
7 #include "ar9331.dtsi"
8
9 / {
10 compatible = "tplink,tl-wr703n", "qca,ar9331";
11 model = "TP-Link TL-WR703N";
12
13 aliases {
14 serial0 = &uart;
15 led-status = &led_system;
16 };
17
18 memory@0 {
19 device_type = "memory";
20 reg = <0x0 0x2000000>;
21 };
22
23 gpio-keys-polled {
24 compatible = "gpio-keys-polled";
25 #address-cells = <1>;
26 #size-cells = <0>;
27 poll-interval = <20>;
28
29 reset {
30 label = "reset";
31 linux,code = <KEY_RESTART>;
32 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
33 debounce-interval = <60>;
34 };
35 };
36
37 gpio-leds {
38 compatible = "gpio-leds";
39
40 led_system: system {
41 label = "tl-wr703n:blue:system";
42 gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
43 };
44 };
45
46 reg_usb_vbus: reg_usb_vbus {
47 compatible = "regulator-fixed";
48 regulator-name = "usb_vbus";
49 regulator-min-microvolt = <5000000>;
50 regulator-max-microvolt = <5000000>;
51 gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
52 enable-active-high;
53 };
54
55 };
56
57 &spi {
58 status = "okay";
59 num-cs = <1>;
60
61 flash@0 {
62 #address-cells = <1>;
63 #size-cells = <1>;
64 compatible = "jedec,spi-nor";
65 reg = <0>;
66 spi-max-frequency = <25000000>;
67
68 partitions {
69 compatible = "fixed-partitions";
70 #address-cells = <1>;
71 #size-cells = <1>;
72
73 uboot: partition@0 {
74 reg = <0x0 0x20000>;
75 label = "u-boot";
76 read-only;
77 };
78
79 firmware: partition@20000 {
80 reg = <0x20000 0x3d0000>;
81 label = "firmware";
82 };
83
84 art: partition@3f0000 {
85 reg = <0x3f0000 0x10000>;
86 label = "art";
87 read-only;
88 };
89 };
90 };
91 };
92
93 &eth0 {
94 status = "okay";
95
96 phy-handle = <&phy4>;
97
98 mtd-mac-address = <&uboot 0x1fc00>;
99
100 gmac-config {
101 device = <&gmac>;
102
103 switch-phy-addr-swap = <0>;
104 switch-phy-swap = <0>;
105 };
106 };
107
108 &gpio {
109 status = "okay";
110 };
111
112 &mdio0 {
113 status = "okay";
114
115 phy4: ethernet-phy@4 {
116 reg = <4>;
117 phy-mode = "mii";
118 };
119 };
120
121 &uart {
122 status = "okay";
123 };
124
125 &usb {
126 dr_mode = "host";
127 vbus-supply = <&reg_usb_vbus>;
128 status = "okay";
129 };
130
131 &usb_phy {
132 status = "okay";
133 };
134
135 &wmac {
136 status = "okay";
137 mtd-cal-data = <&art 0x1000>;
138 mtd-mac-address = <&uboot 0x1fc00>;
139 };