ath79: add support for OCEDO Koala
[openwrt/openwrt.git] / target / linux / ath79 / dts / qca9558_ocedo_koala.dts
1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2 /dts-v1/;
3
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6
7 #include "qca9557.dtsi"
8
9 / {
10 compatible = "ocedo,koala", "qca,qca9557";
11 model = "OCEDO Koala";
12
13 chosen {
14 bootargs = "console=ttyS0,115200n8";
15 };
16
17 aliases {
18 led-status = &system;
19 };
20
21 leds {
22 compatible = "gpio-leds";
23
24 power {
25 label = "koala:green:power";
26 gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
27 default-state = "on";
28 };
29
30 wifi2 {
31 label = "koala:yellow:wlan2";
32 gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
33 linux,default-trigger = "phy1tpt";
34 default-state = "off";
35 };
36
37 wifi5 {
38 label = "koala:red:wlan58";
39 gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
40 linux,default-trigger = "phy0tpt";
41 default-state = "off";
42 };
43
44 system: system {
45 label = "koala:blue:sys";
46 gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
47 default-state = "off";
48 };
49 };
50
51 keys {
52 compatible = "gpio-keys-polled";
53 poll-interval = <100>;
54
55 reset {
56 label = "reset";
57 linux,code = <KEY_RESTART>;
58 gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
59 };
60 };
61 };
62
63 &pcie0 {
64 status = "okay";
65 };
66
67 &uart {
68 status = "okay";
69 };
70
71 &pll {
72 clocks = <&extosc>;
73 };
74
75 &spi {
76 status = "okay";
77 num-cs = <1>;
78
79 flash@0 {
80 compatible = "jedec,spi-nor";
81 reg = <0>;
82 spi-max-frequency = <25000000>;
83
84 partitions {
85 compatible = "fixed-partitions";
86 #address-cells = <1>;
87 #size-cells = <1>;
88
89 uboot: partition@0 {
90 label = "u-boot";
91 reg = <0x000000 0x040000>;
92 read-only;
93 };
94
95 partition@40000 {
96 label = "u-boot-env";
97 reg = <0x040000 0x010000>;
98 };
99
100 partition@50000 {
101 label = "firmware";
102 reg = <0x050000 0x740000>;
103 };
104
105 partition@790000 {
106 label = "vendor";
107 reg = <0x790000 0x740000>;
108 read-only;
109 };
110
111 partition@ed0000 {
112 label = "data";
113 reg = <0xed0000 0x110000>;
114 read-only;
115 };
116
117 partition@fe0000 {
118 label = "id";
119 reg = <0xfe0000 0x010000>;
120 read-only;
121 };
122
123 art: partition@ff0000 {
124 label = "art";
125 reg = <0xff0000 0x010000>;
126 read-only;
127 };
128 };
129 };
130 };
131
132 &wmac {
133 status = "okay";
134
135 mtd-cal-data = <&art 0x1000>;
136 mtd-mac-address = <&art 0x06>;
137 };
138
139 &mdio0 {
140 status = "okay";
141
142 phy5: ethernet-phy@5 {
143 reg = <5>;
144 phy-mode = "rgmii-rxid";
145
146 at803x-disable-smarteee;
147 };
148 };
149
150 &eth0 {
151 status = "okay";
152
153 mtd-mac-address = <&art 0x00>;
154
155 phy-handle = <&phy5>;
156 phy-mode = "rgmii-rxid";
157
158 pll-data = <0xae000000 0xa0000101 0xa0001313>;
159
160 gmac-config {
161 device = <&gmac>;
162
163 rxdv-delay = <3>;
164 rxd-delay = <3>;
165 txen-delay = <0>;
166 txd-delay = <0>;
167 rgmii-enabled = <1>;
168 };
169 };