target/linux/ath79/dts/qca9558_ocedo_koala.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca9557.dtsi"
   8
   9 / {
  10         compatible = "ocedo,koala", "qca,qca9557";
  11         model = "OCEDO Koala";
  12
  13         chosen {
  14                 bootargs = "console=ttyS0,115200n8";
  15         };
  16
  17         aliases {
  18                 led-boot = &system;
  19                 led-failsafe = &system;
  20                 led-running = &system;
  21                 led-upgrade = &system;
  22         };
  23
  24         leds {
  25                 compatible = "gpio-leds";
  26
  27                 power {
  28                         label = "koala:green:power";
  29                         gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
  30                         default-state = "on";
  31                 };
  32
  33                 wifi2 {
  34                         label = "koala:yellow:wlan2";
  35                         gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
  36                         linux,default-trigger = "phy1tpt";
  37                         default-state = "off";
  38                 };
  39
  40                 wifi5 {
  41                         label = "koala:red:wlan58";
  42                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  43                         linux,default-trigger = "phy0tpt";
  44                         default-state = "off";
  45                 };
  46
  47                 system: system {
  48                         label = "koala:blue:sys";
  49                         gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
  50                         default-state = "off";
  51                 };
  52         };
  53
  54         keys {
  55                 compatible = "gpio-keys-polled";
  56                 poll-interval = <100>;
  57
  58                 reset {
  59                         label = "reset";
  60                         linux,code = <KEY_RESTART>;
  61                         gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  62                 };
  63         };
  64 };
  65
  66 &pcie0 {
  67         status = "okay";
  68 };
  69
  70 &uart {
  71         status = "okay";
  72 };
  73
  74 &pll {
  75         clocks = <&extosc>;
  76 };
  77
  78 &spi {
  79         status = "okay";
  80         num-cs = <1>;
  81
  82         flash@0 {
  83                 compatible = "jedec,spi-nor";
  84                 reg = <0>;
  85                 spi-max-frequency = <25000000>;
  86
  87                 partitions {
  88                         compatible = "fixed-partitions";
  89                         #address-cells = <1>;
  90                         #size-cells = <1>;
  91
  92                         uboot: partition@0 {
  93                                 label = "u-boot";
  94                                 reg = <0x000000 0x040000>;
  95                                 read-only;
  96                         };
  97
  98                         partition@40000 {
  99                                 label = "u-boot-env";
 100                                 reg = <0x040000 0x010000>;
 101                         };
 102
 103                         partition@50000 {
 104                                 label = "firmware";
 105                                 reg = <0x050000 0x740000>;
 106                         };
 107
 108                         partition@790000 {
 109                                 label = "vendor";
 110                                 reg = <0x790000 0x740000>;
 111                                 read-only;
 112                         };
 113
 114                         partition@ed0000 {
 115                                 label = "data";
 116                                 reg = <0xed0000 0x110000>;
 117                                 read-only;
 118                         };
 119
 120                         partition@fe0000 {
 121                                 label = "id";
 122                                 reg = <0xfe0000 0x010000>;
 123                                 read-only;
 124                         };
 125
 126                         art: partition@ff0000 {
 127                                 label = "art";
 128                                 reg = <0xff0000 0x010000>;
 129                                 read-only;
 130                         };
 131                 };
 132         };
 133 };
 134
 135 &wmac {
 136         status = "okay";
 137
 138         mtd-cal-data = <&art 0x1000>;
 139         mtd-mac-address = <&art 0x06>;
 140 };
 141
 142 &mdio0 {
 143         status = "okay";
 144
 145         phy5: ethernet-phy@5 {
 146                 reg = <5>;
 147                 phy-mode = "rgmii-rxid";
 148
 149                 at803x-disable-smarteee;
 150         };
 151 };
 152
 153 &eth0 {
 154         status = "okay";
 155
 156         mtd-mac-address = <&art 0x00>;
 157
 158         phy-handle = <&phy5>;
 159         phy-mode = "rgmii-rxid";
 160
 161         pll-data = <0xae000000 0xa0000101 0xa0001313>;
 162
 163         gmac-config {
 164                 device = <&gmac>;
 165
 166                 rxdv-delay = <3>;
 167                 rxd-delay = <3>;
 168                 txen-delay = <0>;
 169                 txd-delay = <0>;
 170                 rgmii-enabled = <1>;
 171         };
 172 };