ath79: add pll for archer c7
[openwrt/openwrt.git] / target / linux / ath79 / dts / qca9558_tplink_archer-c7.dtsi
1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2 /dts-v1/;
3
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6
7 #include "qca9557.dtsi"
8
9 / {
10 chosen {
11 bootargs = "console=ttyS0,115200n8";
12 };
13
14 aliases {
15 led-status = &system;
16 };
17
18 gpio_leds: leds {
19 compatible = "gpio-leds";
20
21 system: system {
22 label = "tp-link:green:system";
23 gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
24 default-state = "on";
25 };
26
27 usb1 {
28 label = "tp-link:green:usb1";
29 gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
30 default-state = "off";
31 trigger-sources = <&hub_port1>;
32 linux,default-trigger = "usbport";
33 };
34
35 usb2 {
36 label = "tp-link:green:usb2";
37 gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
38 default-state = "off";
39 trigger-sources = <&hub_port0>;
40 linux,default-trigger = "usbport";
41 };
42
43 led_wlan2g: wlan2g {
44 label = "tp-link:green:wlan2g";
45 gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
46 default-state = "off";
47 linux,default-trigger = "phy1tpt";
48 };
49
50 qss {
51 label = "tp-link:green:qss";
52 gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
53 default-state = "off";
54 };
55 };
56
57 gpio_keys: keys {
58 compatible = "gpio-keys";
59
60 reset {
61 label = "Reset button";
62 linux,code = <KEY_RESTART>;
63 gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
64 debounce-interval = <60>;
65 };
66 };
67
68 gpio-export {
69 compatible = "gpio-export";
70
71 gpio_usb1_power {
72 gpio-export,name = "tp-link:power:usb1";
73 gpio-export,output = <1>;
74 gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
75 };
76
77 gpio_usb2_power {
78 gpio-export,name = "tp-link:power:usb2";
79 gpio-export,output = <1>;
80 gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
81 };
82
83 };
84 };
85
86 &pcie1 {
87 status = "okay";
88 };
89
90 &uart {
91 status = "okay";
92 };
93
94 &gpio {
95 status = "okay";
96 };
97
98 &usb_phy0 {
99 status = "okay";
100 };
101
102 &usb0 {
103 #address-cells = <1>;
104 #size-cells = <0>;
105 status = "okay";
106
107 hub_port0: port@1 {
108 reg = <1>;
109 #trigger-source-cells = <0>;
110 };
111 };
112
113 &usb_phy1 {
114 status = "okay";
115 };
116
117 &usb1 {
118 #address-cells = <1>;
119 #size-cells = <0>;
120 status = "okay";
121
122 hub_port1: port@1 {
123 reg = <1>;
124 #trigger-source-cells = <0>;
125 };
126 };
127
128 &spi {
129 status = "okay";
130 num-cs = <1>;
131
132 flash@0 {
133 compatible = "jedec,spi-nor";
134 reg = <0>;
135 spi-max-frequency = <25000000>;
136
137 mtdparts: partitions {
138 compatible = "fixed-partitions";
139 #address-cells = <1>;
140 #size-cells = <1>;
141 };
142 };
143 };
144
145 &mdio0 {
146 status = "okay";
147
148 phy0: ethernet-phy@0 {
149 reg = <0>;
150
151 qca,ar8327-initvals = <
152 0x04 0x00080080 /* PORT0 PAD MODE CTRL */
153 0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
154 0x50 0xc737c737 /* LED_CTRL0 */
155 0x54 0x00000000 /* LED_CTRL1 */
156 0x58 0x00000000 /* LED_CTRL2 */
157 0x5c 0x0030c300 /* LED_CTRL3 */
158 0x7c 0x0000007e /* PORT0_STATUS */
159 0x94 0x0000007e /* PORT6 STATUS */
160 >;
161 };
162 };
163
164 &eth0 {
165 status = "okay";
166
167 mtd-mac-address = <&uboot 0x1fc00>;
168 mtd-mac-address-increment = <1>;
169 phy-handle = <&phy0>;
170 pll-data = <0x56000000 0x00000101 0x00001616>;
171
172 gmac-config {
173 device = <&gmac>;
174 rgmii-enabled = <1>;
175 };
176 };
177
178 &eth1 {
179 status = "okay";
180
181 mtd-mac-address = <&uboot 0x1fc00>;
182 pll-data = <0x03000101 0x00000101 0x00001616>;
183
184 fixed-link {
185 speed = <1000>;
186 full-duplex;
187 };
188 };
189
190 &wmac {
191 status = "okay";
192 mtd-cal-data = <&art 0x1000>;
193 mtd-mac-address = <&uboot 0x1fc00>;
194 };