target/linux/ath79/dts/qca955x_zyxel_nbg6x16.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/input/input.h>
   5
   6 #include "qca955x.dtsi"
   7
   8 / {
   9         keys: keys {
  10                 compatible = "gpio-keys";
  11
  12                 wifi {
  13                         label = "WiFi on/off button";
  14                         linux,code = <KEY_RFKILL>;
  15                         linux,input-type = <EV_SW>;
  16                         gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
  17                         debounce-interval = <60>;
  18                 };
  19
  20                 wps {
  21                         label = "WPS button";
  22                         linux,code = <KEY_WPS_BUTTON>;
  23                         gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
  24                         debounce-interval = <60>;
  25                 };
  26
  27                 reset {
  28                         label = "Reset button";
  29                         linux,code = <KEY_RESTART>;
  30                         gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
  31                         debounce-interval = <60>;
  32                 };
  33         };
  34 };
  35
  36 &gpio {
  37         gpio_usb_power: usb_power {
  38                 gpio-hog;
  39                 gpios = <16 0>;
  40                 output-high;
  41         };
  42 };
  43
  44 &uart {
  45         status = "okay";
  46 };
  47
  48 &mdio0 {
  49         status = "okay";
  50
  51         phy17: ethernet-phy@11 {
  52                 reg = <0x11>;
  53                 phy-mode = "rgmii-id";
  54         };
  55
  56         switch0@1f {
  57                 compatible = "qca,ar8327";
  58                 reg = <0x1f>;
  59                 qca,ar8327-initvals = <
  60                         0x04 0x87600000 /* PORT0 PAD MODE CTRL */
  61                         0x0c 0x00080080 /* PORT6 PAD MODE CTRL */
  62                         0x10 0x81000080 /* POWER_ON_STRAP */
  63                         0x50 0xffb7ffb7 /* LED_CTRL0 */
  64                         0x54 0xffb7ffb7 /* LED_CTRL1 */
  65                         0x58 0xffb7ffb7 /* LED_CTRL2 */
  66                         0x5c 0x03ffff00 /* LED_CTRL3 */
  67                         0x7c 0x0000007e /* PORT0_STATUS */
  68                         0x94 0x0000007e /* PORT6 STATUS */
  69                         >;
  70         };
  71 };
  72
  73 &mdio1 {
  74         status = "okay";
  75
  76         phy1: ethernet-phy@1 {
  77                 reg = <1>;
  78                 phy-mode = "sgmii";
  79         };
  80 };
  81
  82
  83 &eth0 {
  84         status = "okay";
  85
  86         pll-data = <0xa6000000 0x00000101 0x00001616>;
  87         phy-handle = <&phy17>;
  88
  89         fixed-link {
  90                 speed = <1000>;
  91                 full-duplex;
  92         };
  93 };
  94
  95 &eth1 {
  96         status = "okay";
  97
  98         pll-data = <0x03000101 0x00000101 0x00001616>;
  99         phy-handle = <&phy1>;
 100
 101         fixed-link {
 102                 speed = <1000>;
 103                 full-duplex;
 104         };
 105 };
 106
 107 &wmac {
 108         status = "okay";
 109
 110         mtd-cal-data = <&art 0x1000>;
 111 };
 112
 113 &usb_phy0 {
 114         status = "okay";
 115 };
 116
 117 &usb_phy1 {
 118         status = "okay";
 119 };
 120
 121 &usb0 {
 122         status = "okay";
 123
 124         hub_port0: port@1 {
 125                 reg = <1>;
 126                 #trigger-source-cells = <0>;
 127         };
 128
 129 };
 130
 131 &usb1 {
 132         status = "okay";
 133
 134         hub_port1: port@1 {
 135                 reg = <1>;
 136                 #trigger-source-cells = <0>;
 137         };
 138 };