target/linux/ath79/dts/qca9563_elecom_wrc-ghbk2-i.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca956x.dtsi"
   8
   9 / {
  10         chosen {
  11                 bootargs = "console=ttyS0,115200n8";
  12         };
  13
  14         aliases {
  15                 led-boot = &power;
  16                 led-failsafe = &power;
  17                 led-running = &power;
  18                 led-upgrade = &power;
  19         };
  20
  21         leds: leds {
  22                 compatible = "gpio-leds";
  23
  24                 wps {
  25                         label = "elecom:red:wps";
  26                         gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
  27                 };
  28         };
  29
  30         keys {
  31                 compatible = "gpio-keys";
  32
  33                 reset {
  34                         label = "reset";
  35                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  36                         linux,code = <KEY_RESTART>;
  37                         debounce-interval = <60>;
  38                 };
  39
  40                 button_wps {
  41                         label = "wps";
  42                         gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
  43                         linux,code = <KEY_WPS_BUTTON>;
  44                         debounce-interval = <60>;
  45                 };
  46
  47                 ap {
  48                         label = "ap";
  49                         gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
  50                         linux,code = <BTN_0>;
  51                         linux,input-type = <EV_SW>;
  52                         debounce-interval = <60>;
  53                 };
  54         };
  55 };
  56
  57 &spi {
  58         status = "okay";
  59         num-cs = <1>;
  60
  61         flash@0 {
  62                 compatible = "jedec,spi-nor";
  63                 reg = <0>;
  64                 spi-max-frequency = <25000000>;
  65
  66                 partitions: partitions {
  67                         compatible = "fixed-partitions";
  68                         #address-cells = <1>;
  69                         #size-cells = <1>;
  70
  71                         partition@0 {
  72                                 label = "u-boot";
  73                                 reg = <0x000000 0x040000>;
  74                                 read-only;
  75                         };
  76
  77                         partition@40000 {
  78                                 label = "u-boot-env";
  79                                 reg = <0x040000 0x010000>;
  80                                 read-only;
  81                         };
  82
  83                         partition@50000 {
  84                                 label = "nvram";
  85                                 reg = <0x050000 0x020000>;
  86                                 read-only;
  87                         };
  88                 };
  89         };
  90 };
  91
  92 &mdio0 {
  93         status = "okay";
  94
  95         phy0: ethernet-phy@0 {
  96                 reg = <0>;
  97
  98                 qca,ar8327-initvals = <
  99                         0x04 0x00000080 /* PORT0 PAD MODE CTRL */
 100                         0x50 0xcf37cf37 /* LED_CTRL0 */
 101                         0x54 0x00000000 /* LED_CTRL1 */
 102                         0x58 0x00000000 /* LED_CTRL2 */
 103                         0x5c 0x03ffff00 /* LED_CTRL3 */
 104                         0x7c 0x0000007e /* PORT0_STATUS */
 105                 >;
 106         };
 107 };
 108
 109 &eth0 {
 110         status = "okay";
 111
 112         pll-data = <0x03000101 0x00000101 0x00001919>;
 113
 114         mtd-mac-address = <&ART 0x1002>;
 115         mtd-mac-address-increment = <(-1)>;
 116         phy-mode = "sgmii";
 117         phy-handle = <&phy0>;
 118 };
 119
 120 &uart {
 121         status = "okay";
 122 };
 123
 124 &wmac {
 125         status = "okay";
 126         mtd-cal-data = <&ART 0x1000>;
 127 };