target/linux/ath79/dts/qca9563_phicomm-k2t.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca956x.dtsi"
   8
   9 / {
  10         model = "Phicomm K2T";
  11         compatible = "phicomm,k2t";
  12
  13         aliases {
  14                 led-status = &status_red;
  15         };
  16
  17         chosen {
  18                 bootargs = "console=ttyS0,115200n8";
  19         };
  20
  21         leds {
  22                 compatible = "gpio-leds";
  23
  24                 status_blue {
  25                         label = "phicomm:blue:status";
  26                         gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
  27                         default-state = "off";
  28                 };
  29
  30                 status_red: status_red {
  31                         label = "phicomm:red:status";
  32                         gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
  33                         default-state = "off";
  34                 };
  35
  36                 status_yellow {
  37                         label = "phicomm:yellow:status";
  38                         gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
  39                         default-state = "off";
  40                 };
  41         };
  42
  43         keys {
  44                 compatible = "gpio-keys-polled";
  45                 #address-cells = <1>;
  46                 #size-cells = <0>;
  47                 poll-interval = <20>;
  48
  49                 reset {
  50                         linux,code = <KEY_RESTART>;
  51                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  52                         debounce-interval = <60>;
  53                 };
  54         };
  55 };
  56
  57 &uart {
  58         status = "okay";
  59 };
  60
  61 &gpio {
  62         status = "okay";
  63 };
  64
  65 &pcie {
  66         status = "okay";
  67 };
  68
  69 &spi {
  70         num-cs = <1>;
  71
  72         status = "okay";
  73
  74         flash@0 {
  75                 #address-cells = <1>;
  76                 #size-cells = <1>;
  77                 compatible = "jedec,spi-nor";
  78                 reg = <0>;
  79                 spi-max-frequency = <25000000>;
  80
  81                 partitions {
  82                         compatible = "fixed-partitions";
  83                         #address-cells = <1>;
  84                         #size-cells = <1>;
  85
  86                         partition@0 {
  87                                 label = "u-boot";
  88                                 reg = <0x000000 0x30000>;
  89                                 read-only;
  90                         };
  91
  92                         partition@30000 {
  93                                 label = "config";
  94                                 reg = <0x030000 0x10000>;
  95                                 read-only;
  96                         };
  97
  98                         partition@40000 {
  99                                 label = "permanent";
 100                                 reg = <0x040000 0x50000>;
 101                                 read-only;
 102                         };
 103
 104                         partition@90000 {
 105                                 label = "firmware";
 106                                 reg = <0x090000 0xf60000>;
 107                         };
 108
 109                         art: partition@ff0000 {
 110                                 label = "art";
 111                                 reg = <0xff0000 0x010000>;
 112                                 read-only;
 113                         };
 114                 };
 115         };
 116 };
 117
 118 &mdio0 {
 119         status = "okay";
 120
 121         phy-mask = <0>;
 122
 123         phy0: ethernet-phy@0 {
 124                 reg = <0>;
 125                 phy-mode = "sgmii";
 126
 127                 qca,ar8327-initvals = <
 128                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
 129                         0x10 0x81000080 /* POWER_ON_STRIP */
 130                         0x50 0xcc35cc35 /* LED_CTRL0 */
 131                         0x54 0xcb37cb37 /* LED_CTRL1 */
 132                         0x58 0x00000000 /* LED_CTRL2 */
 133                         0x5c 0x00f3cf00 /* LED_CTRL3 */
 134                         0x7c 0x0000007e /* PORT0_STATUS */
 135                         >;
 136         };
 137 };
 138
 139 &eth0 {
 140         status = "okay";
 141
 142         pll-data = <0x03000101 0x00000101 0x00001919>;
 143
 144         phy-mode = "sgmii";
 145         phy-handle = <&phy0>;
 146 };
 147
 148 &wmac {
 149         status = "okay";
 150         mtd-cal-data = <&art 0x1000>;
 151 };