target/linux/ath79/dts/qca9563_phicomm_k2t.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca956x.dtsi"
   8
   9 / {
  10         model = "Phicomm K2T";
  11         compatible = "phicomm,k2t";
  12
  13         aliases {
  14                 led-boot = &status_red;
  15                 led-failsafe = &status_red;
  16                 led-running = &status_red;
  17                 led-upgrade = &status_red;
  18         };
  19
  20         chosen {
  21                 bootargs = "console=ttyS0,115200n8";
  22         };
  23
  24         leds {
  25                 compatible = "gpio-leds";
  26
  27                 status_blue {
  28                         label = "phicomm:blue:status";
  29                         gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
  30                         default-state = "off";
  31                 };
  32
  33                 status_red: status_red {
  34                         label = "phicomm:red:status";
  35                         gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
  36                         default-state = "off";
  37                 };
  38
  39                 status_yellow {
  40                         label = "phicomm:yellow:status";
  41                         gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
  42                         default-state = "off";
  43                 };
  44         };
  45
  46         keys {
  47                 compatible = "gpio-keys-polled";
  48                 poll-interval = <20>;
  49
  50                 reset {
  51                         linux,code = <KEY_RESTART>;
  52                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  53                         debounce-interval = <60>;
  54                 };
  55         };
  56 };
  57
  58 &uart {
  59         status = "okay";
  60 };
  61
  62 &gpio {
  63         status = "okay";
  64 };
  65
  66 &pcie {
  67         status = "okay";
  68 };
  69
  70 &spi {
  71         num-cs = <1>;
  72
  73         status = "okay";
  74
  75         flash@0 {
  76                 compatible = "jedec,spi-nor";
  77                 reg = <0>;
  78                 spi-max-frequency = <25000000>;
  79
  80                 partitions {
  81                         compatible = "fixed-partitions";
  82                         #address-cells = <1>;
  83                         #size-cells = <1>;
  84
  85                         partition@0 {
  86                                 label = "u-boot";
  87                                 reg = <0x000000 0x30000>;
  88                                 read-only;
  89                         };
  90
  91                         partition@30000 {
  92                                 label = "config";
  93                                 reg = <0x030000 0x10000>;
  94                                 read-only;
  95                         };
  96
  97                         partition@40000 {
  98                                 label = "permanent";
  99                                 reg = <0x040000 0x50000>;
 100                                 read-only;
 101                         };
 102
 103                         partition@90000 {
 104                                 label = "firmware";
 105                                 reg = <0x090000 0xf60000>;
 106                         };
 107
 108                         art: partition@ff0000 {
 109                                 label = "art";
 110                                 reg = <0xff0000 0x010000>;
 111                                 read-only;
 112                         };
 113                 };
 114         };
 115 };
 116
 117 &mdio0 {
 118         status = "okay";
 119
 120         phy-mask = <0>;
 121
 122         phy0: ethernet-phy@0 {
 123                 reg = <0>;
 124                 phy-mode = "sgmii";
 125
 126                 qca,ar8327-initvals = <
 127                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
 128                         0x10 0x81000080 /* POWER_ON_STRIP */
 129                         0x50 0xcc35cc35 /* LED_CTRL0 */
 130                         0x54 0xcb37cb37 /* LED_CTRL1 */
 131                         0x58 0x00000000 /* LED_CTRL2 */
 132                         0x5c 0x00f3cf00 /* LED_CTRL3 */
 133                         0x7c 0x0000007e /* PORT0_STATUS */
 134                         >;
 135         };
 136 };
 137
 138 &eth0 {
 139         status = "okay";
 140
 141         pll-data = <0x03000101 0x00000101 0x00001919>;
 142
 143         phy-mode = "sgmii";
 144         phy-handle = <&phy0>;
 145 };
 146
 147 &wmac {
 148         status = "okay";
 149         mtd-cal-data = <&art 0x1000>;
 150 };