target/linux/brcm2708/patches-4.4/0201-Add-overlay-and-enable-support-for-QCA7000-board.patch

   1 From 52ca91f1e28a45f4584432525b149f32a0048dd0 Mon Sep 17 00:00:00 2001
   2 From: Michael Heimpold <michael.heimpold@i2se.com>
   3 Date: Fri, 29 Jan 2016 12:00:37 +0100
   4 Subject: [PATCH] Add overlay and enable support for QCA7000 board
   5
   6 This adds a device tree overlay for the QCA7000 which can be used
   7 when attaching an I2SE's PLC Stamp micro EVK to the Raspberry Pi.
   8
   9 This Evaluation Board embeds a QCA7000 chip, a Homeplug Green PHY
  10 powerline chip from Qualcomm/Atheros for the Internet of Things.
  11
  12 This patch also enables the required QCA7000 driver module
  13 in the default configurations.
  14
  15 Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
  16 Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
  17 ---
  18  arch/arm/boot/dts/overlays/Makefile            |  1 +
  19  arch/arm/boot/dts/overlays/README              |  8 ++++
  20  arch/arm/boot/dts/overlays/qca7000-overlay.dts | 52 ++++++++++++++++++++++++++
  21  arch/arm/configs/bcm2709_defconfig             |  1 +
  22  arch/arm/configs/bcmrpi_defconfig              |  1 +
  23  5 files changed, 63 insertions(+)
  24  create mode 100644 arch/arm/boot/dts/overlays/qca7000-overlay.dts
  25
  26 --- a/arch/arm/boot/dts/overlays/Makefile
  27 +++ b/arch/arm/boot/dts/overlays/Makefile
  28 @@ -48,6 +48,7 @@ dtbo-$(RPI_DT_OVERLAYS) += pitft28-resis
  29  dtbo-$(RPI_DT_OVERLAYS) += pps-gpio.dtbo
  30  dtbo-$(RPI_DT_OVERLAYS) += pwm.dtbo
  31  dtbo-$(RPI_DT_OVERLAYS) += pwm-2chan.dtbo
  32 +dtbo-$(RPI_DT_OVERLAYS) += qca7000.dtbo
  33  dtbo-$(RPI_DT_OVERLAYS) += raspidac3.dtbo
  34  dtbo-$(RPI_DT_OVERLAYS) += rpi-backlight.dtbo
  35  dtbo-$(RPI_DT_OVERLAYS) += rpi-dac.dtbo
  36 --- a/arch/arm/boot/dts/overlays/README
  37 +++ b/arch/arm/boot/dts/overlays/README
  38 @@ -625,6 +625,14 @@ Params: pin                     Output p
  39          clock                   PWM clock frequency (informational)
  40
  41
  42 +Name:   qca7000
  43 +Info:   I2SE's Evaluation Board for PLC Stamp micro
  44 +Load:   dtoverlay=qca7000,<param>=<val>
  45 +Params: int_pin                 GPIO pin for interrupt signal (default 23)
  46 +
  47 +        speed                   SPI bus speed (default 12 MHz)
  48 +
  49 +
  50  Name:   raspidac3
  51  Info:   Configures the RaspiDAV Rev.3x audio card
  52  Load:   dtoverlay=raspidac3
  53 --- /dev/null
  54 +++ b/arch/arm/boot/dts/overlays/qca7000-overlay.dts
  55 @@ -0,0 +1,52 @@
  56 +// Overlay for the Qualcomm Atheros QCA7000 on I2SE's PLC Stamp micro EVK
  57 +// Visit: https://www.i2se.com/product/plc-stamp-micro-evk for details
  58 +
  59 +/dts-v1/;
  60 +/plugin/;
  61 +
  62 +/ {
  63 +       compatible = "brcm,bcm2708";
  64 +
  65 +       fragment@0 {
  66 +               target = <&spi0>;
  67 +               __overlay__ {
  68 +                       /* needed to avoid dtc warning */
  69 +                       #address-cells = <1>;
  70 +                       #size-cells = <0>;
  71 +
  72 +                       status = "okay";
  73 +
  74 +                       spidev@0 {
  75 +                               status = "disabled";
  76 +                       };
  77 +
  78 +                       eth1: qca7000@0 {
  79 +                               compatible = "qca,qca7000";
  80 +                               reg = <0>; /* CE0 */
  81 +                               pinctrl-names = "default";
  82 +                               pinctrl-0 = <&eth1_pins>;
  83 +                               interrupt-parent = <&gpio>;
  84 +                               interrupts = <23 0x1>; /* rising edge */
  85 +                               spi-max-frequency = <12000000>;
  86 +                               status = "okay";
  87 +                       };
  88 +               };
  89 +       };
  90 +
  91 +       fragment@1 {
  92 +               target = <&gpio>;
  93 +               __overlay__ {
  94 +                       eth1_pins: eth1_pins {
  95 +                               brcm,pins = <23>;
  96 +                               brcm,function = <0>; /* in */
  97 +                               brcm,pull = <0>; /* none */
  98 +                       };
  99 +               };
 100 +       };
 101 +
 102 +       __overrides__ {
 103 +               int_pin = <&eth1>, "interrupts:0",
 104 +                         <&eth1_pins>, "brcm,pins:0";
 105 +               speed   = <&eth1>, "spi-max-frequency:0";
 106 +       };
 107 +};
 108 --- a/arch/arm/configs/bcm2709_defconfig
 109 +++ b/arch/arm/configs/bcm2709_defconfig
 110 @@ -446,6 +446,7 @@ CONFIG_NETCONSOLE=m
 111  CONFIG_TUN=m
 112  CONFIG_VETH=m
 113  CONFIG_ENC28J60=m
 114 +CONFIG_QCA7000=m
 115  CONFIG_MDIO_BITBANG=m
 116  CONFIG_PPP=m
 117  CONFIG_PPP_BSDCOMP=m
 118 --- a/arch/arm/configs/bcmrpi_defconfig
 119 +++ b/arch/arm/configs/bcmrpi_defconfig
 120 @@ -439,6 +439,7 @@ CONFIG_NETCONSOLE=m
 121  CONFIG_TUN=m
 122  CONFIG_VETH=m
 123  CONFIG_ENC28J60=m
 124 +CONFIG_QCA7000=m
 125  CONFIG_MDIO_BITBANG=m
 126  CONFIG_PPP=m
 127  CONFIG_PPP_BSDCOMP=m