ipq806x: Enlarge R7800 flash - use netgear partition
[openwrt/openwrt.git] / target / linux / ipq806x / files-4.14 / arch / arm / boot / dts / qcom-ipq8065-r7800.dts
1 #include "qcom-ipq8065.dtsi"
2
3 #include <dt-bindings/input/input.h>
4
5 / {
6 model = "Netgear Nighthawk X4S R7800";
7 compatible = "netgear,r7800", "qcom,ipq8065", "qcom,ipq8064";
8
9 memory@0 {
10 reg = <0x42000000 0x1e000000>;
11 device_type = "memory";
12 };
13
14 reserved-memory {
15 #address-cells = <1>;
16 #size-cells = <1>;
17 ranges;
18 rsvd@41200000 {
19 reg = <0x41200000 0x300000>;
20 no-map;
21 };
22
23 rsvd@5fe00000 {
24 reg = <0x5fe00000 0x200000>;
25 reusable;
26 };
27 };
28
29 aliases {
30 serial0 = &gsbi4_serial;
31 mdio-gpio0 = &mdio0;
32
33 led-boot = &power_white;
34 led-failsafe = &power_amber;
35 led-running = &power_white;
36 led-upgrade = &power_amber;
37 };
38
39 chosen {
40 linux,stdout-path = "serial0:115200n8";
41 };
42
43 soc {
44 pinmux@800000 {
45 button_pins: button_pins {
46 mux {
47 pins = "gpio6", "gpio54", "gpio65";
48 function = "gpio";
49 drive-strength = <2>;
50 bias-pull-up;
51 };
52 };
53
54 i2c4_pins: i2c4_pinmux {
55 mux {
56 pins = "gpio12", "gpio13";
57 function = "gsbi4";
58 drive-strength = <12>;
59 bias-disable;
60 };
61 };
62
63 led_pins: led_pins {
64 pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
65 "gpio24","gpio26", "gpio53", "gpio64";
66 function = "gpio";
67 drive-strength = <2>;
68 bias-pull-down;
69 };
70
71 nand_pins: nand_pins {
72 mux {
73 pins = "gpio34", "gpio35", "gpio36",
74 "gpio37", "gpio38", "gpio39",
75 "gpio40", "gpio41", "gpio42",
76 "gpio43", "gpio44", "gpio45",
77 "gpio46", "gpio47";
78 function = "nand";
79 drive-strength = <10>;
80 bias-disable;
81 };
82 pullups {
83 pins = "gpio39";
84 bias-pull-up;
85 };
86 hold {
87 pins = "gpio40", "gpio41", "gpio42",
88 "gpio43", "gpio44", "gpio45",
89 "gpio46", "gpio47";
90 bias-bus-hold;
91 };
92 };
93
94 mdio0_pins: mdio0_pins {
95 mux {
96 pins = "gpio0", "gpio1";
97 function = "gpio";
98 drive-strength = <8>;
99 bias-disable;
100 };
101
102 clk {
103 pins = "gpio1";
104 input-disable;
105 };
106 };
107
108 rgmii2_pins: rgmii2_pins {
109 mux {
110 pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
111 "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
112 function = "rgmii2";
113 drive-strength = <8>;
114 bias-disable;
115 };
116
117 tx {
118 pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
119 input-disable;
120 };
121 };
122
123 spi_pins: spi_pins {
124 mux {
125 pins = "gpio18", "gpio19", "gpio21";
126 function = "gsbi5";
127 bias-pull-down;
128 };
129
130 data {
131 pins = "gpio18", "gpio19";
132 drive-strength = <10>;
133 };
134
135 cs {
136 pins = "gpio20";
137 drive-strength = <10>;
138 bias-pull-up;
139 };
140
141 clk {
142 pins = "gpio21";
143 drive-strength = <12>;
144 };
145 };
146
147 spi6_pins: spi6_pins {
148 mux {
149 pins = "gpio55", "gpio56", "gpio58";
150 function = "gsbi6";
151 bias-pull-down;
152 };
153
154 mosi {
155 pins = "gpio55";
156 drive-strength = <12>;
157 };
158
159 miso {
160 pins = "gpio56";
161 drive-strength = <14>;
162 };
163
164 cs {
165 pins = "gpio57";
166 drive-strength = <12>;
167 bias-pull-up;
168 };
169
170 clk {
171 pins = "gpio58";
172 drive-strength = <12>;
173 };
174
175 reset {
176 pins = "gpio33";
177 drive-strength = <10>;
178 bias-pull-down;
179 output-high;
180 };
181 };
182
183 usb0_pwr_en_pins: usb0_pwr_en_pins {
184 mux {
185 pins = "gpio15";
186 function = "gpio";
187 drive-strength = <12>;
188 bias-pull-down;
189 output-high;
190 };
191 };
192
193 usb1_pwr_en_pins: usb1_pwr_en_pins {
194 mux {
195 pins = "gpio16", "gpio68";
196 function = "gpio";
197 drive-strength = <12>;
198 bias-pull-down;
199 output-high;
200 };
201 };
202 };
203
204 gsbi@16300000 {
205 qcom,mode = <GSBI_PROT_I2C_UART>;
206 status = "ok";
207 serial@16340000 {
208 status = "ok";
209 };
210 /*
211 * The i2c device on gsbi4 should not be enabled.
212 * On ipq806x designs gsbi4 i2c is meant for exclusive
213 * RPM usage. Turning this on in kernel manifests as
214 * i2c failure for the RPM.
215 */
216 };
217
218 sata-phy@1b400000 {
219 status = "ok";
220 };
221
222 sata@29000000 {
223 ports-implemented = <0x1>;
224 status = "ok";
225 };
226
227 phy@100f8800 { /* USB3 port 1 HS phy */
228 status = "ok";
229 };
230
231 phy@100f8830 { /* USB3 port 1 SS phy */
232 status = "ok";
233 };
234
235 phy@110f8800 { /* USB3 port 0 HS phy */
236 status = "ok";
237 };
238
239 phy@110f8830 { /* USB3 port 0 SS phy */
240 status = "ok";
241 };
242
243 usb30@0 {
244 status = "ok";
245
246 pinctrl-0 = <&usb0_pwr_en_pins>;
247 pinctrl-names = "default";
248 };
249
250 usb30@1 {
251 status = "ok";
252
253 pinctrl-0 = <&usb1_pwr_en_pins>;
254 pinctrl-names = "default";
255 };
256
257 pcie0: pci@1b500000 {
258 status = "ok";
259 };
260
261 pcie1: pci@1b700000 {
262 status = "ok";
263 force_gen1 = <1>;
264 };
265
266 nand@1ac00000 {
267 status = "ok";
268
269 pinctrl-0 = <&nand_pins>;
270 pinctrl-names = "default";
271
272 cs0 {
273 reg = <0>;
274 compatible = "qcom,nandcs";
275
276 nand-ecc-strength = <4>;
277 nand-bus-width = <8>;
278 nand-ecc-step-size = <512>;
279
280 partitions {
281 compatible = "fixed-partitions";
282 #address-cells = <1>;
283 #size-cells = <1>;
284
285 qcadata@0 {
286 label = "qcadata";
287 reg = <0x0000000 0x0c80000>;
288 read-only;
289 };
290
291 APPSBL@c80000 {
292 label = "APPSBL";
293 reg = <0x0c80000 0x0500000>;
294 read-only;
295 };
296
297 APPSBLENV@1180000 {
298 label = "APPSBLENV";
299 reg = <0x1180000 0x0080000>;
300 read-only;
301 };
302
303 art: art@1200000 {
304 label = "art";
305 reg = <0x1200000 0x0140000>;
306 read-only;
307 };
308
309 artbak: art@1340000 {
310 label = "artbak";
311 reg = <0x1340000 0x0140000>;
312 read-only;
313 };
314
315 kernel@1480000 {
316 label = "kernel";
317 reg = <0x1480000 0x0400000>;
318 };
319
320 ubi@1880000 {
321 label = "ubi";
322 reg = <0x1880000 0x6080000>;
323 };
324
325 reserve@7900000 {
326 label = "reserve";
327 reg = <0x7900000 0x0700000>;
328 read-only;
329 };
330
331 firmware@1480000 {
332 label = "firmware";
333 reg = <0x1480000 0x6480000>;
334 };
335 };
336 };
337 };
338
339 mdio0: mdio {
340 compatible = "virtual,mdio-gpio";
341 #address-cells = <1>;
342 #size-cells = <0>;
343 gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
344 pinctrl-0 = <&mdio0_pins>;
345 pinctrl-names = "default";
346
347
348 phy0: ethernet-phy@0 {
349 device_type = "ethernet-phy";
350 reg = <0>;
351 qca,ar8327-initvals = <
352 0x00004 0x7600000 /* PAD0_MODE */
353 0x00008 0x1000000 /* PAD5_MODE */
354 0x0000c 0x80 /* PAD6_MODE */
355 0x000e4 0xaa545 /* MAC_POWER_SEL */
356 0x000e0 0xc74164de /* SGMII_CTRL */
357 0x0007c 0x4e /* PORT0_STATUS */
358 0x00094 0x4e /* PORT6_STATUS */
359 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */
360 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */
361 0x00978 0x19008643 /* QM_PORT1_CTRL0 */
362 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */
363 0x00980 0x19008643 /* QM_PORT2_CTRL0 */
364 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */
365 0x00988 0x19008643 /* QM_PORT3_CTRL0 */
366 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */
367 0x00990 0x19008643 /* QM_PORT4_CTRL0 */
368 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */
369 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */
370 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */
371 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */
372 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */
373 >;
374 qca,ar8327-vlans = <
375 0x1 0x5e /* VLAN1 Ports 1/2/3/4/6 */
376 0x2 0x21 /* VLAN2 Ports 0/5 */
377 >;
378 };
379
380 phy4: ethernet-phy@4 {
381 device_type = "ethernet-phy";
382 reg = <4>;
383 qca,ar8327-initvals = <
384 0x000e4 0x6a545 /* MAC_POWER_SEL */
385 0x0000c 0x80 /* PAD6_MODE */
386 >;
387 };
388 };
389
390 gmac1: ethernet@37200000 {
391 status = "ok";
392 phy-mode = "rgmii";
393 qcom,id = <1>;
394 qcom,phy_mdio_addr = <4>;
395 qcom,poll_required = <0>;
396 qcom,rgmii_delay = <1>;
397 qcom,phy_mii_type = <0>;
398 qcom,emulation = <0>;
399 qcom,irq = <255>;
400 mdiobus = <&mdio0>;
401
402 pinctrl-0 = <&rgmii2_pins>;
403 pinctrl-names = "default";
404
405 mtd-mac-address = <&art 6>;
406
407 fixed-link {
408 speed = <1000>;
409 full-duplex;
410 };
411 };
412
413 gmac2: ethernet@37400000 {
414 status = "ok";
415 phy-mode = "sgmii";
416 qcom,id = <2>;
417 qcom,phy_mdio_addr = <0>; /* none */
418 qcom,poll_required = <0>; /* no polling */
419 qcom,rgmii_delay = <0>;
420 qcom,phy_mii_type = <1>;
421 qcom,emulation = <0>;
422 qcom,irq = <258>;
423 mdiobus = <&mdio0>;
424
425 mtd-mac-address = <&art 0>;
426
427 fixed-link {
428 speed = <1000>;
429 full-duplex;
430 };
431 };
432 };
433
434 gpio-keys {
435 compatible = "gpio-keys";
436 pinctrl-0 = <&button_pins>;
437 pinctrl-names = "default";
438
439 wifi {
440 label = "wifi";
441 gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
442 linux,code = <KEY_RFKILL>;
443 debounce-interval = <60>;
444 wakeup-source;
445 };
446
447 reset {
448 label = "reset";
449 gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
450 linux,code = <KEY_RESTART>;
451 debounce-interval = <60>;
452 wakeup-source;
453 };
454
455 wps {
456 label = "wps";
457 gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
458 linux,code = <KEY_WPS_BUTTON>;
459 debounce-interval = <60>;
460 wakeup-source;
461 };
462 };
463
464 gpio-leds {
465 compatible = "gpio-leds";
466 pinctrl-0 = <&led_pins>;
467 pinctrl-names = "default";
468
469 power_white: power_white {
470 label = "r7800:white:power";
471 gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
472 default-state = "keep";
473 };
474
475 power_amber: power_amber {
476 label = "r7800:amber:power";
477 gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
478 };
479
480 wan_white {
481 label = "r7800:white:wan";
482 gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
483 };
484
485 wan_amber {
486 label = "r7800:amber:wan";
487 gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
488 };
489
490 usb1 {
491 label = "r7800:white:usb1";
492 gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
493 };
494
495 usb2 {
496 label = "r7800:white:usb2";
497 gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
498 };
499
500 esata {
501 label = "r7800:white:esata";
502 gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
503 };
504
505 wifi {
506 label = "r7800:white:wifi";
507 gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
508 };
509
510 wps {
511 label = "r7800:white:wps";
512 gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
513 };
514 };
515 };
516
517 &adm_dma {
518 status = "ok";
519 };