ipq806x: clean up dts patch
[openwrt/openwrt.git] / target / linux / ipq806x / files-4.9 / arch / arm / boot / dts / qcom-ipq8064-r7500.dts
1 #include "qcom-ipq8064-v1.0.dtsi"
2
3 #include <dt-bindings/input/input.h>
4
5 / {
6 model = "Netgear Nighthawk X4 R7500";
7 compatible = "netgear,r7500", "qcom,ipq8064";
8
9 memory@0 {
10 reg = <0x42000000 0xe000000>;
11 device_type = "memory";
12 };
13
14 reserved-memory {
15 #address-cells = <1>;
16 #size-cells = <1>;
17 ranges;
18 rsvd@41200000 {
19 reg = <0x41200000 0x300000>;
20 no-map;
21 };
22 };
23
24 aliases {
25 serial0 = &gsbi4_serial;
26 mdio-gpio0 = &mdio0;
27
28 led-boot = &power_white;
29 led-failsafe = &power_amber;
30 led-running = &power_white;
31 led-upgrade = &power_amber;
32 };
33
34 chosen {
35 bootargs = "rootfstype=squashfs noinitrd";
36 linux,stdout-path = "serial0:115200n8";
37 };
38
39 soc {
40 pinmux@800000 {
41 button_pins: button_pins {
42 mux {
43 pins = "gpio6", "gpio54", "gpio65";
44 function = "gpio";
45 drive-strength = <2>;
46 bias-pull-up;
47 };
48 };
49
50 i2c4_pins: i2c4_pinmux {
51 mux {
52 pins = "gpio12", "gpio13";
53 function = "gsbi4";
54 drive-strength = <12>;
55 bias-disable;
56 };
57 };
58
59 led_pins: led_pins {
60 mux {
61 pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
62 "gpio24","gpio26", "gpio53", "gpio64";
63 function = "gpio";
64 drive-strength = <2>;
65 bias-pull-up;
66 };
67 };
68
69 mdio0_pins: mdio0_pins {
70 mux {
71 pins = "gpio0", "gpio1";
72 function = "gpio";
73 drive-strength = <8>;
74 bias-disable;
75 };
76 };
77
78 nand_pins: nand_pins {
79 mux {
80 pins = "gpio34", "gpio35", "gpio36",
81 "gpio37", "gpio38", "gpio39",
82 "gpio40", "gpio41", "gpio42",
83 "gpio43", "gpio44", "gpio45",
84 "gpio46", "gpio47";
85 function = "nand";
86 drive-strength = <10>;
87 bias-disable;
88 };
89 pullups {
90 pins = "gpio39";
91 bias-pull-up;
92 };
93 hold {
94 pins = "gpio40", "gpio41", "gpio42",
95 "gpio43", "gpio44", "gpio45",
96 "gpio46", "gpio47";
97 bias-bus-hold;
98 };
99 };
100
101 rgmii2_pins: rgmii2_pins {
102 mux {
103 pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
104 "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
105 function = "rgmii2";
106 drive-strength = <8>;
107 bias-disable;
108 };
109 };
110 };
111
112 gsbi@16300000 {
113 qcom,mode = <GSBI_PROT_I2C_UART>;
114 status = "ok";
115 serial@16340000 {
116 status = "ok";
117 };
118 /*
119 * The i2c device on gsbi4 should not be enabled.
120 * On ipq806x designs gsbi4 i2c is meant for exclusive
121 * RPM usage. Turning this on in kernel manifests as
122 * i2c failure for the RPM.
123 */
124 };
125
126 sata-phy@1b400000 {
127 status = "ok";
128 };
129
130 sata@29000000 {
131 status = "ok";
132 };
133
134 phy@100f8800 { /* USB3 port 1 HS phy */
135 status = "ok";
136 };
137
138 phy@100f8830 { /* USB3 port 1 SS phy */
139 status = "ok";
140 };
141
142 phy@110f8800 { /* USB3 port 0 HS phy */
143 status = "ok";
144 };
145
146 phy@110f8830 { /* USB3 port 0 SS phy */
147 status = "ok";
148 };
149
150 usb30@0 {
151 status = "ok";
152 };
153
154 usb30@1 {
155 status = "ok";
156 };
157
158 pcie0: pci@1b500000 {
159 status = "ok";
160 };
161
162 pcie1: pci@1b700000 {
163 status = "ok";
164 };
165
166 nand@1ac00000 {
167 status = "ok";
168
169 pinctrl-0 = <&nand_pins>;
170 pinctrl-names = "default";
171
172 nand-ecc-strength = <4>;
173 nand-bus-width = <8>;
174
175 #address-cells = <1>;
176 #size-cells = <1>;
177
178 qcadata@0 {
179 label = "qcadata";
180 reg = <0x0000000 0x0c80000>;
181 read-only;
182 };
183
184 APPSBL@c80000 {
185 label = "APPSBL";
186 reg = <0x0c80000 0x0500000>;
187 read-only;
188 };
189
190 APPSBLENV@1180000 {
191 label = "APPSBLENV";
192 reg = <0x1180000 0x0080000>;
193 read-only;
194 };
195
196 art: art@1200000 {
197 label = "art";
198 reg = <0x1200000 0x0140000>;
199 read-only;
200 };
201
202 kernel@1340000 {
203 label = "kernel";
204 reg = <0x1340000 0x0200000>;
205 };
206
207 ubi@1540000 {
208 label = "ubi";
209 reg = <0x1540000 0x1800000>;
210 };
211
212 netgear@2d40000 {
213 label = "netgear";
214 reg = <0x2d40000 0x0c00000>;
215 read-only;
216 };
217
218 reserve@3940000 {
219 label = "reserve";
220 reg = <0x3940000 0x46c0000>;
221 read-only;
222 };
223
224 firmware@1340000 {
225 label = "firmware";
226 reg = <0x1340000 0x1a00000>;
227 };
228
229 };
230
231 mdio0: mdio {
232 compatible = "virtual,mdio-gpio";
233 #address-cells = <1>;
234 #size-cells = <0>;
235 gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
236 pinctrl-0 = <&mdio0_pins>;
237 pinctrl-names = "default";
238
239 phy0: ethernet-phy@0 {
240 device_type = "ethernet-phy";
241 reg = <0>;
242 qca,ar8327-initvals = <
243 0x00004 0x7600000 /* PAD0_MODE */
244 0x00008 0x1000000 /* PAD5_MODE */
245 0x0000c 0x80 /* PAD6_MODE */
246 0x000e4 0x6a545 /* MAC_POWER_SEL */
247 0x000e0 0xc74164de /* SGMII_CTRL */
248 0x0007c 0x4e /* PORT0_STATUS */
249 0x00094 0x4e /* PORT6_STATUS */
250 >;
251 };
252
253 phy4: ethernet-phy@4 {
254 device_type = "ethernet-phy";
255 reg = <4>;
256 };
257 };
258
259 gmac1: ethernet@37200000 {
260 status = "ok";
261 phy-mode = "rgmii";
262 qcom,id = <1>;
263
264 pinctrl-0 = <&rgmii2_pins>;
265 pinctrl-names = "default";
266
267 mtd-mac-address = <&art 6>;
268
269 fixed-link {
270 speed = <1000>;
271 full-duplex;
272 };
273 };
274
275 gmac2: ethernet@37400000 {
276 status = "ok";
277 phy-mode = "sgmii";
278 qcom,id = <2>;
279
280 mtd-mac-address = <&art 0>;
281
282 fixed-link {
283 speed = <1000>;
284 full-duplex;
285 };
286 };
287
288 rpm@108000 {
289 pinctrl-0 = <&i2c4_pins>;
290 pinctrl-names = "default";
291 };
292 };
293
294 gpio-keys {
295 compatible = "gpio-keys";
296 pinctrl-0 = <&button_pins>;
297 pinctrl-names = "default";
298
299 wifi {
300 label = "wifi";
301 gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
302 linux,code = <KEY_RFKILL>;
303 };
304
305 reset {
306 label = "reset";
307 gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
308 linux,code = <KEY_RESTART>;
309 };
310
311 wps {
312 label = "wps";
313 gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
314 linux,code = <KEY_WPS_BUTTON>;
315 };
316 };
317
318 gpio-leds {
319 compatible = "gpio-leds";
320 pinctrl-0 = <&led_pins>;
321 pinctrl-names = "default";
322
323 usb1 {
324 label = "r7500:white:usb1";
325 gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
326 };
327
328 usb2 {
329 label = "r7500:white:usb2";
330 gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
331 };
332
333 power_amber: power_amber {
334 label = "r7500:amber:power";
335 gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
336 };
337
338 wan_white {
339 label = "r7500:white:wan";
340 gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
341 };
342
343 wan_amber {
344 label = "r7500:amber:wan";
345 gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
346 };
347
348 wps {
349 label = "r7500:white:wps";
350 gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
351 };
352
353 esata {
354 label = "r7500:white:esata";
355 gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
356 };
357
358 power_white: power_white {
359 label = "r7500:white:power";
360 gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
361 default-state = "keep";
362 };
363
364 wifi {
365 label = "r7500:white:wifi";
366 gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
367 };
368 };
369 };
370
371 &adm_dma {
372 status = "ok";
373 };