kernel: update kernel 3.18 to 3.18.26
[openwrt/openwrt.git] / target / linux / ipq806x / patches-3.18 / 801-ARM-qcom-add-Netgear-Nighthawk-X4-D7800-device-tree.patch
1 --- a/arch/arm/boot/dts/Makefile
2 +++ b/arch/arm/boot/dts/Makefile
3 @@ -362,6 +362,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
4 qcom-ipq8064-ap148.dtb \
5 qcom-ipq8064-db149.dtb \
6 qcom-ipq8064-r7500.dtb \
7 + qcom-ipq8064-d7800.dtb \
8 qcom-msm8660-surf.dtb \
9 qcom-msm8960-cdp.dtb \
10 qcom-msm8974-sony-xperia-honami.dtb
11 --- /dev/null
12 +++ b/arch/arm/boot/dts/qcom-ipq8064-d7800.dts
13 @@ -0,0 +1,368 @@
14 +#include "qcom-ipq8064-v1.0.dtsi"
15 +
16 +#include <dt-bindings/input/input.h>
17 +
18 +/ {
19 + model = "Netgear Nighthawk X4 D7800";
20 + compatible = "netgear,d7800", "qcom,ipq8064";
21 +
22 + memory@0 {
23 + reg = <0x42000000 0xe000000>;
24 + device_type = "memory";
25 + };
26 +
27 + reserved-memory {
28 + #address-cells = <1>;
29 + #size-cells = <1>;
30 + ranges;
31 + rsvd@41200000 {
32 + reg = <0x41200000 0x300000>;
33 + no-map;
34 + };
35 + };
36 +
37 + aliases {
38 + serial0 = &uart4;
39 + mdio-gpio0 = &mdio0;
40 + };
41 +
42 + chosen {
43 + bootargs = "rootfstype=squashfs noinitrd";
44 + linux,stdout-path = "serial0:115200n8";
45 + };
46 +
47 + soc {
48 + pinmux@800000 {
49 + i2c4_pins: i2c4_pinmux {
50 + pins = "gpio12", "gpio13";
51 + function = "gsbi4";
52 + bias-disable;
53 + };
54 +
55 + pcie0_pins: pcie0_pinmux {
56 + mux {
57 + pins = "gpio3";
58 + function = "pcie1_rst";
59 + drive-strength = <12>;
60 + bias-disable;
61 + };
62 + };
63 +
64 + pcie1_pins: pcie1_pinmux {
65 + mux {
66 + pins = "gpio48";
67 + function = "pcie2_rst";
68 + drive-strength = <12>;
69 + bias-disable;
70 + };
71 + };
72 +
73 + nand_pins: nand_pins {
74 + mux {
75 + pins = "gpio34", "gpio35", "gpio36",
76 + "gpio37", "gpio38", "gpio39",
77 + "gpio40", "gpio41", "gpio42",
78 + "gpio43", "gpio44", "gpio45",
79 + "gpio46", "gpio47";
80 + function = "nand";
81 + drive-strength = <10>;
82 + bias-disable;
83 + };
84 + pullups {
85 + pins = "gpio39";
86 + bias-pull-up;
87 + };
88 + hold {
89 + pins = "gpio40", "gpio41", "gpio42",
90 + "gpio43", "gpio44", "gpio45",
91 + "gpio46", "gpio47";
92 + bias-bus-hold;
93 + };
94 + };
95 +
96 + mdio0_pins: mdio0_pins {
97 + mux {
98 + pins = "gpio0", "gpio1";
99 + function = "gpio";
100 + drive-strength = <8>;
101 + bias-disable;
102 + };
103 + };
104 +
105 + rgmii2_pins: rgmii2_pins {
106 + mux {
107 + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
108 + "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
109 + function = "rgmii2";
110 + drive-strength = <8>;
111 + bias-disable;
112 + };
113 + };
114 + };
115 +
116 + gsbi@16300000 {
117 + qcom,mode = <GSBI_PROT_I2C_UART>;
118 + status = "ok";
119 + serial@16340000 {
120 + status = "ok";
121 + };
122 + /*
123 + * The i2c device on gsbi4 should not be enabled.
124 + * On ipq806x designs gsbi4 i2c is meant for exclusive
125 + * RPM usage. Turning this on in kernel manifests as
126 + * i2c failure for the RPM.
127 + */
128 + };
129 +
130 + sata-phy@1b400000 {
131 + status = "ok";
132 + };
133 +
134 + sata@29000000 {
135 + status = "ok";
136 + };
137 +
138 + phy@100f8800 { /* USB3 port 1 HS phy */
139 + status = "ok";
140 + };
141 +
142 + phy@100f8830 { /* USB3 port 1 SS phy */
143 + status = "ok";
144 + };
145 +
146 + phy@110f8800 { /* USB3 port 0 HS phy */
147 + status = "ok";
148 + };
149 +
150 + phy@110f8830 { /* USB3 port 0 SS phy */
151 + status = "ok";
152 + };
153 +
154 + usb30@0 {
155 + status = "ok";
156 + };
157 +
158 + usb30@1 {
159 + status = "ok";
160 + };
161 +
162 + pcie0: pci@1b500000 {
163 + status = "ok";
164 + reset-gpio = <&qcom_pinmux 3 0>;
165 + pinctrl-0 = <&pcie0_pins>;
166 + pinctrl-names = "default";
167 + };
168 +
169 + pcie1: pci@1b700000 {
170 + status = "ok";
171 + reset-gpio = <&qcom_pinmux 48 0>;
172 + pinctrl-0 = <&pcie1_pins>;
173 + pinctrl-names = "default";
174 + };
175 +
176 + nand@1ac00000 {
177 + status = "ok";
178 +
179 + pinctrl-0 = <&nand_pins>;
180 + pinctrl-names = "default";
181 +
182 + nand-ecc-strength = <4>;
183 + nand-bus-width = <8>;
184 +
185 + #address-cells = <1>;
186 + #size-cells = <1>;
187 +
188 + qcadata@0 {
189 + label = "qcadata";
190 + reg = <0x0000000 0x0c80000>;
191 + read-only;
192 + };
193 +
194 + APPSBL@c80000 {
195 + label = "APPSBL";
196 + reg = <0x0c80000 0x0500000>;
197 + read-only;
198 + };
199 +
200 + APPSBLENV@1180000 {
201 + label = "APPSBLENV";
202 + reg = <0x1180000 0x0080000>;
203 + read-only;
204 + };
205 +
206 + art: art@1200000 {
207 + label = "art";
208 + reg = <0x1200000 0x0140000>;
209 + read-only;
210 + };
211 +
212 + artbak: art@1340000 {
213 + label = "artbak";
214 + reg = <0x1340000 0x0140000>;
215 + read-only;
216 + };
217 +
218 + kernel@1480000 {
219 + label = "kernel";
220 + reg = <0x1480000 0x0200000>;
221 + };
222 +
223 + ubi@1680000 {
224 + label = "ubi";
225 + reg = <0x1680000 0x1E00000>;
226 + };
227 +
228 + netgear@3480000 {
229 + label = "netgear";
230 + reg = <0x3480000 0x4480000>;
231 + read-only;
232 + };
233 +
234 + reserve@7900000 {
235 + label = "reserve";
236 + reg = <0x7900000 0x0700000>;
237 + read-only;
238 + };
239 +
240 + firmware@1480000 {
241 + label = "firmware";
242 + reg = <0x1480000 0x2000000>;
243 + };
244 +
245 + };
246 +
247 + mdio0: mdio {
248 + compatible = "virtual,mdio-gpio";
249 + #address-cells = <1>;
250 + #size-cells = <0>;
251 + gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
252 + pinctrl-0 = <&mdio0_pins>;
253 + pinctrl-names = "default";
254 +
255 + phy0: ethernet-phy@0 {
256 + device_type = "ethernet-phy";
257 + reg = <0>;
258 + qca,ar8327-initvals = <
259 + 0x00004 0x7600000 /* PAD0_MODE */
260 + 0x00008 0x1000000 /* PAD5_MODE */
261 + 0x0000c 0x80 /* PAD6_MODE */
262 + 0x000e4 0xaa545 /* MAC_POWER_SEL */
263 + 0x000e0 0xc74164de /* SGMII_CTRL */
264 + 0x0007c 0x4e /* PORT0_STATUS */
265 + 0x00094 0x4e /* PORT6_STATUS */
266 + >;
267 + };
268 +
269 + phy4: ethernet-phy@4 {
270 + device_type = "ethernet-phy";
271 + reg = <4>;
272 + };
273 + };
274 +
275 + gmac1: ethernet@37200000 {
276 + status = "ok";
277 + phy-mode = "rgmii";
278 + phy-handle = <&phy4>;
279 + qcom,id = <1>;
280 +
281 + pinctrl-0 = <&rgmii2_pins>;
282 + pinctrl-names = "default";
283 +
284 + mtd-mac-address = <&art 6>;
285 + };
286 +
287 + gmac2: ethernet@37400000 {
288 + status = "ok";
289 + phy-mode = "sgmii";
290 + qcom,id = <2>;
291 +
292 + mtd-mac-address = <&art 0>;
293 +
294 + fixed-link {
295 + speed = <1000>;
296 + full-duplex;
297 + };
298 + };
299 + };
300 +
301 + gpio-keys {
302 + compatible = "gpio-keys";
303 +
304 + wifi {
305 + label = "wifi";
306 + gpios = <&qcom_pinmux 6 1>;
307 + linux,code = <KEY_WLAN>;
308 + };
309 +
310 + reset {
311 + label = "reset";
312 + gpios = <&qcom_pinmux 54 1>;
313 + linux,code = <KEY_RESTART>;
314 + };
315 +
316 + wps {
317 + label = "wps";
318 + gpios = <&qcom_pinmux 65 1>;
319 + linux,code = <KEY_WPS_BUTTON>;
320 + };
321 + };
322 +
323 + gpio-leds {
324 + compatible = "gpio-leds";
325 +
326 + usb1 {
327 + label = "d7800:amber:usb1";
328 + gpios = <&qcom_pinmux 7 0>;
329 + };
330 +
331 + usb3 {
332 + label = "d7800:amber:usb3";
333 + gpios = <&qcom_pinmux 8 0>;
334 + };
335 +
336 + status {
337 + label = "d7800:amber:status";
338 + gpios = <&qcom_pinmux 9 0>;
339 + };
340 +
341 + internet {
342 + label = "d7800:white:internet";
343 + gpios = <&qcom_pinmux 22 0>;
344 + };
345 +
346 + wan {
347 + label = "d7800:white:wan";
348 + gpios = <&qcom_pinmux 23 0>;
349 + };
350 +
351 + wps {
352 + label = "d7800:white:wps";
353 + gpios = <&qcom_pinmux 24 0>;
354 + };
355 +
356 + esata {
357 + label = "d7800:white:esata";
358 + gpios = <&qcom_pinmux 26 0>;
359 + };
360 +
361 + power {
362 + label = "d7800:white:power";
363 + gpios = <&qcom_pinmux 53 0>;
364 + default-state = "on";
365 + };
366 +
367 + rfkill {
368 + label = "d7800:white:rfkill";
369 + gpios = <&qcom_pinmux 64 0>;
370 + };
371 +
372 + wifi5g {
373 + label = "d7800:white:wifi5g";
374 + gpios = <&qcom_pinmux 67 0>;
375 + };
376 + };
377 +};
378 +
379 +&adm_dma {
380 + status = "ok";
381 +};