target/linux/ramips/dts/AR670W.dts

   1 /dts-v1/;
   2
   3 #include "rt2880.dtsi"
   4
   5 / {
   6         compatible = "AR670W", "ralink,rt2880-soc";
   7         model = "Airlink101 AR670W";
   8
   9         cfi@bdc00000 {
  10                 compatible = "cfi-flash";
  11                 reg = <0xbc400000 0x800000>;
  12                 bank-width = <2>;
  13                 #address-cells = <1>;
  14                 #size-cells = <1>;
  15
  16                 u-boot@0 {
  17                         reg = <0x0 0x30000>;
  18                         label = "u-boot";
  19                         read-only;
  20                 };
  21
  22                 factory: factory@30000 {
  23                         reg = <0x30000 0x10000>;
  24                         label = "factory";
  25                         read-only;
  26                 };
  27
  28                 firmware@40000 {
  29                         reg = <0x40000 0x3c0000>;
  30                         label = "firmware";
  31                 };
  32         };
  33
  34         gpio-leds {
  35                 compatible = "gpio-leds";
  36
  37                 status {
  38                         label = "ar670w:green:power";
  39                         gpios = <&gpio0 7 1>;
  40                 };
  41
  42                 wpsblue {
  43                         label = "ar670w:blue:wps";
  44                         gpios = <&gpio0 13 1>;
  45                 };
  46         };
  47
  48         gpio-keys-polled {
  49                 compatible = "gpio-keys-polled";
  50                 #address-cells = <1>;
  51                 #size-cells = <0>;
  52                 poll-interval = <100>;
  53
  54                 wps {
  55                         label = "wps";
  56                         gpios = <&gpio0 0 1>;
  57                         linux,code = <0x211>;
  58                 };
  59
  60                 reset {
  61                         label = "reset";
  62                         gpios = <&gpio0 9 1>;
  63                         linux,code = <0x198>;
  64                 };
  65         };
  66 };
  67
  68 &gpio0 {
  69         status = "okay";
  70 };
  71
  72 &pinctrl {
  73         state_default: pinctrl0 {
  74                 gpio {
  75                         ralink,group = "i2c", "spi", "uartlite";
  76                         ralink,function = "gpio";
  77                 };
  78         };
  79 };
  80
  81 &ethernet {
  82         status = "okay";
  83         mtd-mac-address = <&factory 0x2004>;
  84
  85         port@0 {
  86                 phy-handle = <&phy0>;
  87                 phy-mode = "mii";
  88         };
  89
  90         mdio-bus {
  91                 status = "okay";
  92
  93                 phy0: ethernet-phy@0 {
  94                         phy-mode = "mii";
  95                         reg = <0>;
  96                 };
  97         };
  98 };
  99
 100 &wmac {
 101         status = "okay";
 102         ralink,mtd-eeprom = <&factory 0x2000>;
 103 };