target/linux/ramips/dts/WNCE2001.dts

   1 /dts-v1/;
   2
   3 #include "rt3050.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         compatible = "netgear,wnce2001", "ralink,rt3052-soc";
  10         model = "Netgear WNCE2001";
  11
  12         chosen {
  13                 bootargs = "console=ttyS0,115200";
  14         };
  15
  16         gpio-leds {
  17                 compatible = "gpio-leds";
  18
  19                 power-green {
  20                         label = "wnce2001:green:power";
  21                         gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
  22                 };
  23
  24                 power-red {
  25                         label = "wnce2001:red:power";
  26                         gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
  27                 };
  28
  29                 wlan-green {
  30                         label = "wnce2001:green:wlan";
  31                         gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
  32                 };
  33
  34                 wlan-red {
  35                         label = "wnce2001:red:wlan";
  36                         gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
  37                 };
  38         };
  39
  40         gpio-keys-polled {
  41                 compatible = "gpio-keys-polled";
  42                 #address-cells = <1>;
  43                 #size-cells = <0>;
  44                 poll-interval = <20>;
  45
  46                 reset {
  47                         label = "reset";
  48                         gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
  49                         linux,code = <KEY_RESTART>;
  50                 };
  51
  52                 wps {
  53                         label = "wps";
  54                         gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
  55                         linux,code = <KEY_WPS_BUTTON>;
  56                 };
  57
  58                 rt {
  59                         label = "rt";
  60                         gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
  61                         linux,code = <BTN_0>;
  62                 };
  63
  64                 ap {
  65                         label = "ap";
  66                         gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
  67                         linux,code = <BTN_1>;
  68                 };
  69         };
  70 };
  71
  72 &spi0 {
  73         status = "okay";
  74
  75         m25p80@0 {
  76                 #address-cells = <1>;
  77                 #size-cells = <1>;
  78                 compatible = "jedec,spi-nor";
  79                 reg = <0>;
  80                 spi-max-frequency = <10000000>;
  81
  82                 partition@0 {
  83                         label = "u-boot";
  84                         reg = <0x0 0x30000>;
  85                         read-only;
  86                 };
  87
  88                 factory: partition@30000 {
  89                         label = "factory";
  90                         reg = <0x30000 0x10000>;
  91                         read-only;
  92                 };
  93
  94                 partition@40000 {
  95                         label = "config";
  96                         reg = <0x40000 0x20000>;
  97                         read-only;
  98                 };
  99
 100                 partition@60000 {
 101                         label = "language";
 102                         reg = <0x60000 0x30000>;
 103                         read-only;
 104                 };
 105
 106                 partition@90000 {
 107                         label = "pot";
 108                         reg = <0x90000 0x10000>;
 109                         read-only;
 110                 };
 111
 112                 partition@a0000 {
 113                         label = "checksum";
 114                         reg = <0xa0000 0x10000>;
 115                 };
 116
 117                 partition@b0000 {
 118                         label = "firmware";
 119                         reg = <0xb0000 0x350000>;
 120                 };
 121         };
 122 };
 123
 124 &pinctrl {
 125         state_default: pinctrl0 {
 126                 gpio {
 127                         ralink,group = "i2c", "jtag", "rgmii", "mdio", "uartf";
 128                         ralink,function = "gpio";
 129                 };
 130         };
 131 };
 132
 133 &ethernet {
 134         mtd-mac-address = <&factory 0x28>;
 135 };
 136
 137 &wmac {
 138         ralink,mtd-eeprom = <&factory 0>;
 139 };