target/linux/ramips/dts/WZR-AGL300NH.dts

   1 /dts-v1/;
   2
   3 #include "rt2880.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         #address-cells = <1>;
  10         #size-cells = <1>;
  11         compatible = "buffalo,wzr-agl300nh", "ralink,rt2880-soc";
  12         model = "Buffalo WZR-AGL300NH";
  13
  14         pci@440000 {
  15                 status = "ok";
  16         };
  17
  18         cfi@1f000000 {
  19                 compatible = "cfi-flash";
  20                 reg = <0x1f000000 0x800000>;
  21                 bank-width = <2>;
  22                 device-width = <2>;
  23                 #address-cells = <1>;
  24                 #size-cells = <1>;
  25
  26                 partition@0 {
  27                         label = "uboot";
  28                         reg = <0x0 0x30000>;
  29                         read-only;
  30                 };
  31
  32                 partition@30000 {
  33                         label = "uboot-env";
  34                         reg = <0x30000 0x10000>;
  35                         read-only;
  36                 };
  37
  38                 factory: partition@40000 {
  39                         label = "factory";
  40                         reg = <0x40000 0x10000>;
  41                         read-only;
  42                 };
  43
  44                 partition@50000 {
  45                         label = "firmware";
  46                         reg = <0x50000 0x3b0000>;
  47                 };
  48         };
  49
  50         rtl8366s {
  51                 compatible = "realtek,rtl8366s";
  52                 gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>;
  53                 gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>;
  54         };
  55
  56         gpio-keys-polled {
  57                 compatible = "gpio-keys-polled";
  58                 #address-cells = <1>;
  59                 #size-cells = <0>;
  60                 poll-interval = <100>;
  61
  62                 wps {
  63                         label = "wps";
  64                         gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
  65                         linux,code = <KEY_WPS_BUTTON>;
  66                 };
  67
  68                 router {
  69                         label = "router_switch";
  70                         gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
  71                         linux,code = <BTN_0>;
  72                 };
  73
  74                 reset {
  75                         label = "reset";
  76                         gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
  77                         linux,code = <KEY_RESTART>;
  78                 };
  79         };
  80
  81         gpio-leds {
  82                 compatible = "gpio-leds";
  83
  84                 router {
  85                         label = "wzr-agl300nh:green:router";
  86                         gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
  87                 };
  88
  89                 diag {
  90                         label = "wzr-agl300nh:red:diag";
  91                         gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
  92                 };
  93
  94                 security_g {
  95                         label = "wzr-agl300nh:orange:security_g";
  96                         gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
  97                 };
  98
  99                 security_n {
 100                         label = "wzr-agl300nh:orange:security_n";
 101                         gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
 102                 };
 103         };
 104 };
 105
 106 &gpio0 {
 107         status = "okay";
 108 };
 109
 110 &pinctrl {
 111         state_default: pinctrl0 {
 112                 gpio {
 113                         ralink,group = "i2c", "uartlite", "mdio";
 114                         ralink,function = "gpio";
 115                 };
 116         };
 117 };
 118
 119 &ethernet {
 120         status = "okay";
 121         mtd-mac-address = <&factory 0x4>;
 122
 123         port@0 {
 124                 mediatek,fixed-link = <1000 1 1 1>;
 125         };
 126
 127         mdio-bus {
 128                 status = "okay";
 129
 130                 phy0: ethernet-phy@0 {
 131                         phy-mode = "mii";
 132                         reg = <0>;
 133                 };
 134         };
 135 };
 136
 137 &wmac {
 138         ralink,mtd-eeprom = <&factory 0>;
 139 };