#!/bin/sh /etc/rc.common # Copyright (C) 2012 OpenWrt.org # needs to start before the atm layer which starts at 50 START=48 USE_PROCD=1 EXTRA_COMMANDS="status lucistat" EXTRA_HELP=" status Get DSL status information lucistat Get status information if lua friendly format" [ -f /lib/functions/lantiq_dsl.sh ] && . /lib/functions/lantiq_dsl.sh # # ITU-T G.997.1 (06/2012) - Section 7.3.1.1.1 (xTU transmission system enabling (XTSE)) # ITU-T G.997.1 Amendment 2 (04/2013) - Section 2.1 - (Vectoring mode enable (VECTORMODE_ENABLE)) # # G.992.1 Annex A # G.992.3 Annex A / L-US1 / L_US-2 / M # G.992.5 Annex A / M # G.993.2 Annex A/B/C # G.993.5 Annex A/B/C xtse_xdsl_a="04_00_04_00_4C_01_04_0F" # G.992.1 Annex B # G.992.3 Annex B # G.992.5 Annex B # G.993.2 Annex A/B/C # G.993.5 Annex A/B/C xtse_xdsl_b="10_00_10_00_00_04_00_0F" # G.992.1 Annex B # G.992.3 Annex B # G.992.3 Annex J # G.992.5 Annex B # G.992.5 Annex J # G.993.2 Annex A/B/C # G.993.5 Annex A/B/C xtse_xdsl_j="10_00_10_40_00_04_01_0F" # # ITU-T G.994.1 (06/2012) - Table 2 (Mandatory carrier sets) # # A43 tone_adsl_a="0x142" # A43C + J43 + A43 tone_vdsl_a="0x142" # A43C + J43 + A43 # A43 + V43 tone_adsl_av="0x142" # A43C + J43 + A43 tone_vdsl_av="0x146" # A43C + J43 + A43 + V43 # B43 tone_adsl_b="0x81" # B43 + B43c tone_vdsl_b="0x1" # B43 # B43 + V43 tone_adsl_bv="0x81" # B43 + B43c tone_vdsl_bv="0x5" # B43 + V43 lowlevel_cfg() { echo "# VRX Low Level Configuration File # # Parameters must be separated by tabs or spaces. # Empty lines and comments will be ignored. # # nFilter # # NA = -1 # OFF = 0 # ISDN = 1 # POTS = 2 # POTS_2 = 3 # POTS_3 = 4 # # (dec) -1 # nHsToneGroupMode nHsToneGroup_A nHsToneGroup_V nHsToneGroup_AV # # NA = -1 NA = -1 see see # AUTO = 0 VDSL2_B43 = 0x0001 nHsToneGroup_A nHsToneGroup_A # MANUAL = 1 VDSL2_A43 = 0x0002 # VDSL2_V43 = 0x0004 # VDSL1_V43P = 0x0008 # VDSL1_V43I = 0x0010 # ADSL1_C43 = 0x0020 # ADSL2_J43 = 0x0040 # ADSL2_B43C = 0x0080 # ADSL2_A43C = 0x0100 # # (dec) (hex) (hex) (hex) 1 $1 $2 0x0 # nBaseAddr nIrqNum # # (hex) (dec) 0x1e116000 63 # nUtopiaPhyAdr nUtopiaBusWidth nPosPhyParity # default(16b) = 0 NA = -1 # 8-bit = 1 ODD = 0 # 16-bit = 2 # # # (hex) (dec) (dec) 0xFF 0 0 # bNtrEnable # # (dec) 0" > /tmp/lowlevel.cfg } service_triggers() { procd_add_reload_trigger network } start_service() { local annex local firmware local tone local tone_adsl local tone_vdsl local xtse local mode local lowlevel config_load network config_get tone dsl tone config_get annex dsl annex config_get firmware dsl firmware config_get xfer_mode dsl xfer_mode eval "xtse=\"\${xtse_xdsl_$annex}\"" [ -z "${xfer_mode}" ] && xfer_mode=ptm case "${xfer_mode}" in atm) LOAD=ltq_atm_vr9 UNLOAD=ltq_ptm_vr9 mode=1 # mask out VDSL bits when ATM is requested xtse="${xtse%_*}_00" ;; *) LOAD=ltq_ptm_vr9 UNLOAD=ltq_atm_vr9 mode=2 ;; esac [ -z "${firmware}" ] && firmware=/lib/firmware/vdsl.bin [ -f "${firmware}" ] || { echo failed to find $firmware return 1 } eval "tone_adsl=\"\${tone_adsl_$tone}\"" eval "tone_vdsl=\"\${tone_vdsl_$tone}\"" [ -n "${tone_adsl}" ] && [ -n "${tone_vdsl}" ] && { lowlevel_cfg "${tone_adsl}" "${tone_vdsl}" lowlevel="-l /tmp/lowlevel.cfg" } procd_open_instance procd_set_param command /sbin/vdsl_cpe_control_wrapper \ -i$xtse \ -n /sbin/dsl_notify.sh \ -f ${firmware} \ $lowlevel \ -M ${mode} procd_append_param env "LOAD=$LOAD" "UNLOAD=$UNLOAD" procd_close_instance } stop_service() { DSL_NOTIFICATION_TYPE="DSL_INTERFACE_STATUS" \ DSL_INTERFACE_STATUS="DOWN" \ /sbin/dsl_notify.sh }