config_add_string hwmode
config_add_int beacon_int chanbw frag rts
config_add_int rxantenna txantenna antenna_gain txpower distance
- config_add_boolean noscan
+ config_add_boolean noscan ht_coex
config_add_array ht_capab
+ config_add_array channels
config_add_boolean \
rxldpc \
short_gi_80 \
json_select config
[ "$auto_channel" -gt 0 ] && channel=acs_survey
+ [ "$auto_channel" -gt 0 ] && json_get_values channel_list channels
- json_get_vars noscan
+ json_get_vars noscan ht_coex
json_get_values ht_capab_list ht_capab
ieee80211n=1
[ -n "$ieee80211n" ] && {
append base_cfg "ieee80211n=1" "$N"
+ set_default ht_coex 0
+ append base_cfg "ht_coex=$ht_coex" "$N"
+
json_get_vars \
ldpc:1 \
greenfield:0 \
vht_max_a_mpdu_len_exp:7 \
vht_max_mpdu:11454 \
rx_stbc:4 \
- tx_stbc:4 \
vht_link_adapt:3 \
vht160:2
cap_rx_stbc=$((($vht_cap >> 8) & 7))
[ "$rx_stbc" -lt "$cap_rx_stbc" ] && cap_rx_stbc="$rx_stbc"
- ht_cap_mask="$(( ($vht_cap & ~(0x700)) | ($cap_rx_stbc << 8) ))"
+ vht_cap="$(( ($vht_cap & ~(0x700)) | ($cap_rx_stbc << 8) ))"
mac80211_add_capabilities vht_capab $vht_cap \
RXLDPC:0x10::$rxldpc \
SHORT-GI-80:0x20::$short_gi_80 \
SHORT-GI-160:0x40::$short_gi_160 \
- TX-STBC-2BY1:0x80::$tx_stbc \
+ TX-STBC-2BY1:0x80::$tx_stbc_2by1 \
SU-BEAMFORMER:0x800::$su_beamformer \
SU-BEAMFORMEE:0x1000::$su_beamformee \
MU-BEAMFORMER:0x80000::$mu_beamformer \
HTC-VHT:0x400000::$htc_vht \
RX-ANTENNA-PATTERN:0x10000000::$rx_antenna_pattern \
TX-ANTENNA-PATTERN:0x20000000::$tx_antenna_pattern \
- RX-STBC1:0x700:0x100:1 \
- RX-STBC12:0x700:0x200:1 \
- RX-STBC123:0x700:0x300:1 \
- RX-STBC1234:0x700:0x400:1 \
+ RX-STBC-1:0x700:0x100:1 \
+ RX-STBC-12:0x700:0x200:1 \
+ RX-STBC-123:0x700:0x300:1 \
+ RX-STBC-1234:0x700:0x400:1 \
# supported Channel widths
vht160_hw=0
hostapd_prepare_device_config "$hostapd_conf_file" nl80211
cat >> "$hostapd_conf_file" <<EOF
${channel:+channel=$channel}
+${channel_list:+chanlist=$channel_list}
${noscan:+noscan=$noscan}
$base_cfg
find_phy() {
[ -n "$phy" -a -d /sys/class/ieee80211/$phy ] && return 0
[ -n "$path" ] && {
- for phy in /sys/devices/$path/ieee80211/phy*; do
- [ -e "$phy" ] && {
- phy="${phy##*/}"
- return 0
- }
+ for phy in $(ls /sys/class/ieee80211 2>/dev/null); do
+ case "$(readlink -f /sys/class/ieee80211/$phy/device)" in
+ *$path) return 0;;
+ esac
done
}
[ -n "$macaddr" ] && {
mac80211_hostapd_setup_bss "$phy" "$ifname" "$macaddr" "$type" || return
[ -n "$hostapd_ctrl" ] || {
- iw phy "$phy" interface add "$ifname" type managed
+ iw phy "$phy" interface add "$ifname" type __ap
hostapd_ctrl="${hostapd_ctrl:-/var/run/hostapd/$ifname}"
}
;;
mesh)
- json_get_vars key mesh_id
- if [ -n "$key" ]; then
- iw phy "$phy" interface add "$ifname" type mp
- else
- iw phy "$phy" interface add "$ifname" type mp mesh_id "$mesh_id"
- fi
+ iw phy "$phy" interface add "$ifname" type mp
;;
monitor)
iw phy "$phy" interface add "$ifname" type monitor
# All interfaces must have unique mac addresses
# which can either be explicitly set in the device
# section, or automatically generated
- ifconfig "$ifname" hw ether "$macaddr"
+ ip link set dev "$ifname" address "$macaddr"
fi
json_select ..
mac80211_setup_adhoc_htmode() {
case "$htmode" in
VHT20|HT20) ibss_htmode=HT20;;
- HT40*|VHT40|VHT80|VHT160)
+ HT40*|VHT40|VHT160)
case "$hwmode" in
a)
case "$(( ($channel / 4) % 2 ))" in
esac
[ "$auto_channel" -gt 0 ] && ibss_htmode="HT40+"
;;
+ VHT80)
+ ibss_htmode="80MHZ"
+ ;;
+ NONE|NOHT)
+ ibss_htmode="NOHT"
+ ;;
*) ibss_htmode="" ;;
esac
json_get_vars mode
json_get_var vif_txpower txpower
- ifconfig "$ifname" up || {
+ ip link set dev "$ifname" up || {
wireless_setup_vif_failed IFUP_ERROR
json_select ..
return
case "$mode" in
mesh)
- for var in $MP_CONFIG_INT $MP_CONFIG_BOOL $MP_CONFIG_STRING; do
- json_get_var mp_val "$var"
- [ -n "$mp_val" ] && iw dev "$ifname" set mesh_param "$var" "$mp_val"
- done
-
- # authsae
+ # authsae or wpa_supplicant
json_get_vars key
if [ -n "$key" ]; then
if [ -e "/lib/wifi/authsae.sh" ]; then
. /lib/wifi/authsae.sh
authsae_start_interface || failed=1
else
- wireless_setup_vif_failed AUTHSAE_NOT_INSTALLED
- json_select ..
- return
+ wireless_vif_parse_encryption
+ mac80211_setup_supplicant || failed=1
fi
+ else
+ json_get_vars mesh_id mcast_rate
+
+ mcval=
+ [ -n "$mcast_rate" ] && wpa_supplicant_add_rate mcval "$mcast_rate"
+
+ case "$htmode" in
+ VHT20|HT20) mesh_htmode=HT20;;
+ HT40*|VHT40)
+ case "$hwmode" in
+ a)
+ case "$(( ($channel / 4) % 2 ))" in
+ 1) mesh_htmode="HT40+" ;;
+ 0) mesh_htmode="HT40-";;
+ esac
+ ;;
+ *)
+ case "$htmode" in
+ HT40+) mesh_htmode="HT40+";;
+ HT40-) mesh_htmode="HT40-";;
+ *)
+ if [ "$channel" -lt 7 ]; then
+ mesh_htmode="HT40+"
+ else
+ mesh_htmode="HT40-"
+ fi
+ ;;
+ esac
+ ;;
+ esac
+ ;;
+ VHT80)
+ mesh_htmode="80Mhz"
+ ;;
+ VHT160)
+ mesh_htmode="160Mhz"
+ ;;
+ *) mesh_htmode="NOHT" ;;
+ esac
+
+ freq="$(get_freq "$phy" "$channel")"
+ iw dev "$ifname" mesh join "$mesh_id" freq $freq $mesh_htmode ${mcval:+mcast-rate $mcval}
fi
+
+ for var in $MP_CONFIG_INT $MP_CONFIG_BOOL $MP_CONFIG_STRING; do
+ json_get_var mp_val "$var"
+ [ -n "$mp_val" ] && iw dev "$ifname" set mesh_param "$var" "$mp_val"
+ done
;;
adhoc)
wireless_vif_parse_encryption
local phy="$1"
for wdev in $(list_phy_interfaces "$phy"); do
- ifconfig "$wdev" down 2>/dev/null
+ ip link set dev "$wdev" down 2>/dev/null
iw dev "$wdev" del
done
}
for_each_interface "ap" mac80211_prepare_vif
[ -n "$hostapd_ctrl" ] && {
- /usr/sbin/hostapd -P /var/run/wifi-$phy.pid -B "$hostapd_conf_file"
+ /usr/sbin/hostapd -s -P /var/run/wifi-$phy.pid -B "$hostapd_conf_file"
ret="$?"
wireless_add_process "$(cat /var/run/wifi-$phy.pid)" "/usr/sbin/hostapd" 1
[ "$ret" != 0 ] && {
projects / openwrt / openwrt.git / blobdiff