lantiq: rename gphy firmware
[openwrt/openwrt.git] / target / linux / lantiq / dts / P2812HNUFX.dtsi
index a03129f..ec3bd10 100644 (file)
@@ -1,50 +1,32 @@
-/include/ "vr9.dtsi"
+#include "vr9.dtsi"
+
+#include <dt-bindings/input/input.h>
 
 / {
+       compatible = "zyxel,p-2812hnu", "lantiq,xway", "lantiq,vr9";
+
        chosen {
-               bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
+               bootargs = "console=ttyLTQ0,115200";
+       };
 
-               leds {
-                       dsl = &dsl;
-                       internet = &internet_green;
-                       power = &power;
-                       power2 = &power2;
-                       usb = &usb1;
-                       usb2 = &usb2;
-                       wifi = &wireless_green;
-               };
+       aliases {
+               led-boot = &power_green;
+               led-failsafe = &power_red;
+               led-running = &power_green;
+
+               led-dsl = &dsl_green;
+               led-internet = &internet_green;
+               led-wifi = &wireless_green;
        };
 
        memory@0 {
                reg = <0x0 0x8000000>;
        };
 
-        fpi@10000000 {
-               #address-cells = <1>;
-               #size-cells = <1>;
-               compatible = "lantiq,fpi", "simple-bus";
-               ranges = <0x0 0x10000000 0xEEFFFFF>;
-               reg = <0x10000000 0xEF00000>;
-
-               localbus@0 {
-                       #address-cells = <2>;
-                       #size-cells = <1>;
-                       ranges = <0 0 0x0 0x3ffffff /* addrsel0 */
-                               1 0 0x4000000 0x4000010>; /* addsel1 */
-                       compatible = "lantiq,localbus", "simple-bus";
-               };
-
+       fpi@10000000 {
                gpio: pinmux@E100B10 {
-                       compatible = "lantiq,pinctrl-xr9";
                        pinctrl-names = "default";
                        pinctrl-0 = <&state_default>;
-                       
-                       interrupt-parent = <&icu0>;
-                       interrupts = <166 135 66 40 41 42 38>;
-
-                       #gpio-cells = <2>;
-                       gpio-controller;
-                       reg = <0xE100B10 0xA0>;
 
                        state_default: pinmux {
                                exin3 {
                        };
                };
 
-               eth@E108000 {
-                       #address-cells = <1>;
-                       #size-cells = <0>;
-                       compatible = "lantiq,xrx200-net";
-                       reg = < 0xE108000 0x3000        /* switch */
-                               0xE10B100 0x70          /* mdio */
-                               0xE10B1D8 0x30          /* mii */
-                               0xE10B308 0x30 >;       /* pmac */
-                       interrupt-parent = <&icu0>;
-                       interrupts = <73 72>;
-
-                       lan: interface@0 {
-                               compatible = "lantiq,xrx200-pdi";
-                               #address-cells = <1>;
-                               #size-cells = <0>;
-                               reg = <0>;
-                               mac-address = [ 00 11 22 33 44 55 ];
-                               lantiq,switch;
-
-                               ethernet@0 {
-                                       compatible = "lantiq,xrx200-pdi-port";
-                                       reg = <0>;
-                                       phy-mode = "rgmii";
-                                       phy-handle = <&phy0>;
-                               };
-                               ethernet@1 {
-                                       compatible = "lantiq,xrx200-pdi-port";
-                                       reg = <1>;
-                                       phy-mode = "rgmii";
-                                       phy-handle = <&phy1>;
-                               };
-                               ethernet@2 {
-                                       compatible = "lantiq,xrx200-pdi-port";
-                                       reg = <2>;
-                                       phy-mode = "gmii";
-                                       phy-handle = <&phy11>;
-                               };
-                               ethernet@4 {
-                                       compatible = "lantiq,xrx200-pdi-port";
-                                       reg = <4>;
-                                       phy-mode = "gmii";
-                                       phy-handle = <&phy13>;
-                               };
-                               ethernet@5 {
-                                       compatible = "lantiq,xrx200-pdi-port";
-                                       reg = <5>;
-                                       phy-mode = "rgmii";
-                                       phy-handle = <&phy5>;
-                               };
-                       };
-
-                       mdio@0 {
-                               #address-cells = <1>;
-                               #size-cells = <0>;
-                               compatible = "lantiq,xrx200-mdio";
-
-                               phy0: ethernet-phy@0 {
-                                       reg = <0x0>;
-                                       compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
-                               };
-                               phy1: ethernet-phy@1 {
-                                       reg = <0x1>;
-                                       compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
-                               };
-                               phy5: ethernet-phy@5 {
-                                       reg = <0x5>;
-                                       compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
-                               };
-                               phy11: ethernet-phy@11 {
-                                       reg = <0x11>;
-                                       compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
-                               };
-                               phy13: ethernet-phy@13 {
-                                       reg = <0x13>;
-                                       compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
-                               };
-                       };
-               };
-
                stp: stp@E100BB0 {
                        compatible = "lantiq,gpio-stp-xway";
                        reg = <0xE100BB0 0x40>;
 
                ifxhcd@E101000 {
                        status = "okay";
-                       gpios = <&gpio 33 0>;
+                       gpios = <&gpio 33 GPIO_ACTIVE_HIGH>;
                        lantiq,portmask = <0x3>;
                };
 
                ifxhcd@E106000 {
                        status = "okay";
-                       gpios = <&gpio 33 0>;
+                       gpios = <&gpio 33 GPIO_ACTIVE_HIGH>;
                };
 
                pci@E105400 {
                        status = "okay";
-                       #address-cells = <3>;
-                       #size-cells = <2>;
-                       #interrupt-cells = <1>;
-                       compatible = "lantiq,pci-xway";
-                       bus-range = <0x0 0x0>;
-                       ranges = <0x2000000 0 0x8000000 0x8000000 0 0x2000000   /* pci memory */
-                               0x1000000 0 0x00000000 0xAE00000 0 0x200000>; /* io space */
-                       reg = <0x7000000 0x8000         /* config space */
-                               0xE105400 0x400>;       /* pci bridge */
-                       lantiq,bus-clock = <33333333>;
-                       /*lantiq,external-clock;*/
-                       lantiq,delay-hi = <0>; /* 0ns delay */
-                       lantiq,delay-lo = <0>; /* 0.0ns delay */
-                       interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
-                       interrupt-map = <
-                               0x7000 0 0 1 &icu0 30 1 // slot 14, irq 30
-                               >;
-                       gpio-reset = <&gpio 21 0>;
-                       req-mask = <0x1>;       /* GNT1 */
+                       gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
                };
        };
 
        gphy-xrx200 {
                compatible = "lantiq,phy-xrx200";
-               firmware1 = "lantiq/vr9_phy11g_a1x.bin";        /*VR9 1.1*/
-               firmware2 = "lantiq/vr9_phy11g_a2x.bin";        /*VR9 1.2*/
+               firmware1 = "lantiq/xrx200_phy11g_a14.bin";     /*VR9 1.1*/
+               firmware2 = "lantiq/xrx200_phy11g_a22.bin";     /*VR9 1.2*/
                phys = [ 00 01 ];
        };
 
 
                reset {
                        label = "reset";
-                       gpios = <&gpio 39 1>;
-                       linux,code = <0x198>;
+                       gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
                };
 
                rfkill {
                        label = "rfkill";
-                       gpios = <&gpio 1 1>;
-                       linux,code = <0xf7>;
+                       gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RFKILL>;
                };
        };
 
        gpio-leds {
                compatible = "gpio-leds";
 
-               internet_red {                          /* red */
-                       label = "internet_red";
-                       gpios = <&stp 16 1>;
+               internet_red {
+                       label = "p2812hnufx:red:internet";
+                       gpios = <&stp 16 GPIO_ACTIVE_LOW>;
                };
                internet_green: internet_green {
-                       label = "internet_green";       /* green */
-                       gpios = <&stp 17 1>;
+                       label = "p2812hnufx:green:internet";
+                       gpios = <&stp 17 GPIO_ACTIVE_LOW>;
+               };
+               dsl_green: dsl_green {
+                       label = "p2812hnufx:green:dsl";
+                       gpios = <&stp 18 GPIO_ACTIVE_LOW>;
+               };
+               dsl_orange {
+                       label = "p2812hnufx:orange:dsl";
+                       gpios = <&stp 19 GPIO_ACTIVE_LOW>;
+               };
+               wireless_orange {
+                       label = "p2812hnufx:orange:wlan";
+                       gpios = <&stp 20 GPIO_ACTIVE_LOW>;
+               };
+               wireless_green: wireless_green {
+                       label = "p2812hnufx:green:wlan";
+                       gpios = <&stp 21 GPIO_ACTIVE_LOW>;
+               };
+               power_red: power {
+                       label = "p2812hnufx:red:power";
+                       gpios = <&stp 22 GPIO_ACTIVE_LOW>;
+               };
+               power_green: power2 {
+                       label = "p2812hnufx:green:power";
+                       gpios = <&stp 23 GPIO_ACTIVE_LOW>;
+                       default-state = "keep";
+               };
+               phone1 {
+                       label = "p2812hnufx:green:phone";
+                       gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
                };
-               dsl: dsl {
-                       label = "dsl";
-                       gpios = <&stp 18 1>;
+               phone1warn {
+                       label = "p2812hnufx:orange:phone";
+                       gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
                };
-               dsl2 {
-                       label = "dsl2";
-                       gpios = <&stp 19 1>;
+               phone2warn {
+                       label = "p2812hnufx:orange:phone2";
+                       gpios = <&gpio 26 GPIO_ACTIVE_LOW>;
                };
-               wireless_red {                          /* red */
-                       label = "wireless_red";
-                       gpios = <&stp 20 1>;
+               phone2 {
+                       label = "p2812hnufx:green:phone2";
+                       gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
                };
-               wireless_green: wireless_green {                        /* green */
-                       label = "wireless_green";
-                       gpios = <&stp 21 1>;
+       };
+};
+
+&eth0 {
+       lan: interface@0 {
+               compatible = "lantiq,xrx200-pdi";
+               #address-cells = <1>;
+               #size-cells = <0>;
+               reg = <0>;
+               mac-address = [ 00 11 22 33 44 55 ];
+               lantiq,switch;
+
+               ethernet@0 {
+                       compatible = "lantiq,xrx200-pdi-port";
+                       reg = <0>;
+                       phy-mode = "rgmii";
+                       phy-handle = <&phy0>;
                };
-               power: power {                                  /* red */
-                       label = "power";
-                       gpios = <&stp 22 1>;
+               ethernet@1 {
+                       compatible = "lantiq,xrx200-pdi-port";
+                       reg = <1>;
+                       phy-mode = "rgmii";
+                       phy-handle = <&phy1>;
                };
-               power2: power2 {                                /* green */
-                       label = "power2";
-                       gpios = <&stp 23 1>;
+               ethernet@2 {
+                       compatible = "lantiq,xrx200-pdi-port";
+                       reg = <2>;
+                       phy-mode = "gmii";
+                       phy-handle = <&phy11>;
                };
-               usb1: usb1 {                                    /* green */
-                       label = "usb1";
-                       gpios = <&gpio 38 1>;
+               ethernet@4 {
+                       compatible = "lantiq,xrx200-pdi-port";
+                       reg = <4>;
+                       phy-mode = "gmii";
+                       phy-handle = <&phy13>;
                };
-               usb2: usb2 {                                    /* green */
-                       label = "usb2";
-                       gpios = <&gpio 44 1>;
+               ethernet@5 {
+                       compatible = "lantiq,xrx200-pdi-port";
+                       reg = <5>;
+                       phy-mode = "rgmii";
+                       phy-handle = <&phy5>;
+               };
+       };
+
+       mdio@0 {
+               #address-cells = <1>;
+               #size-cells = <0>;
+               compatible = "lantiq,xrx200-mdio";
+
+               phy0: ethernet-phy@0 {
+                       reg = <0x0>;
+                       compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
                };
-               phone1 {                                /* green */
-                       label = "phone1";
-                       gpios = <&gpio 11 1>;
+               phy1: ethernet-phy@1 {
+                       reg = <0x1>;
+                       compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
                };
-               phone1warn {                            /* red */
-                       label = "phone1warn";
-                       gpios = <&gpio 12 1>;
+               phy5: ethernet-phy@5 {
+                       reg = <0x5>;
+                       compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
                };
-               phone2warn {                            /* red */
-                       label = "phone2warn";
-                       gpios = <&gpio 26 1>;
+               phy11: ethernet-phy@11 {
+                       reg = <0x11>;
+                       compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
                };
-               phone2 {                                /* green */
-                       label = "phone2";
-                       gpios = <&gpio 28 1>;
+               phy13: ethernet-phy@13 {
+                       reg = <0x13>;
+                       compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
                };
        };
 };