ramips: add support for D-Link DWR-116-A1/2

[openwrt/openwrt.git] / target / linux / ramips / base-files / etc / hotplug.d / firmware / 10-rt2x00-eeprom

diff --git a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
index 47f7f016af166f85c945127d049ce8066422305b..67c05c9a461225dd847c6447c8123f088da01e30 100644 (file)
--- a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
+++ b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
@@ -11,63 +11,62 @@ rt2x00_eeprom_extract() {
        local count=$3
        local mtd
 
-       . /etc/functions.sh
+       mtd=$(find_mtd_part $part)
+       [ -n "$mtd" ] || \
+               rt2x00_eeprom_die "no mtd device found for partition $part"
+
+       dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
+               rt2x00_eeprom_die "failed to extract from $mtd"
+}
+
+jboot_eeprom_extract() {
+       local part=$1
+       local offset=$2
+       local mtd
 
        mtd=$(find_mtd_part $part)
        [ -n "$mtd" ] || \
                rt2x00_eeprom_die "no mtd device found for partition $part"
 
-       dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count || \
+       jboot_config_read -i $mtd -o $offset -e /lib/firmware/$FIRMWARE  2>/dev/null || \
                rt2x00_eeprom_die "failed to extract from $mtd"
 }
 
-[ -e /lib/firmware/$FIRMWARE ] && exit 0
+rt2x00_eeprom_set_macaddr() {
+       local macaddr=$1
 
-case "$FIRMWARE" in
-"RT288X.eeprom" | \
-"RT305X.eeprom")
-       . /lib/ramips.sh
+       [ -n "$macaddr" ] || \
+               rt2x00_eeprom_die "invalid wlan mac address"
 
-       local board=$(ramips_board_name)
+       macaddr_2bin $macaddr | dd of=/lib/firmware/$FIRMWARE \
+                               conv=notrunc bs=1 seek=4 count=6 2>/dev/null || \
+               rt2x00_eeprom_die "failed to write mac address to eeprom file"
+}
 
-       case $board in
-       dir-300-b1 | \
-       dir-600-b1 | \
-       dir-600-b2)
-               rt2x00_eeprom_extract "devdata" 16384 272
-               ;;
+FW="/lib/firmware/$FIRMWARE"
+[ -e "$FW" ] && exit 0
 
-       rt-g32-b1)
-               rt2x00_eeprom_extract "devconf" 0 272
-               ;;
+. /lib/functions.sh
+. /lib/functions/system.sh
 
-       f5d8235-v2)
-               rt2x00_eeprom_extract "u-boot" 262144 272
-               ;;
+board=$(board_name)
 
-       argus-atp52b | \
-       bc2 | \
-       esr-9753 | \
-       fonera20n | \
-       hw550-3g | \
-       mofi3500-3gn | \
-       pwh2004 | \
-       nbg-419n | \
-       nw718 | \
-       omni-emb | \
-       rt-n15 | \
-       v22rw-2x2 | \
-       w502u | \
-       wcr-150gn | \
-       whr-g300n | \
-       wl-351 | \
-       wli-tx4-ag300n | \
-       wr512-3gn)
-               rt2x00_eeprom_extract "factory" 0 272
+case "$FIRMWARE" in
+"soc_wmac.eeprom")
+       case $board in
+       dlink,dwr-116-a1)
+               wan_mac=$(jboot_config_read -m -i $(find_mtd_part "config") -o 0xE000)
+               wifi_mac=$(macaddr_add "$wan_mac" 1)
+               jboot_eeprom_extract "config" 0xE000
+               rt2x00_eeprom_set_macaddr $wifi_mac
+               ;;
+       tiny-ac)
+               wifi_mac=$(mtd_get_mac_ascii u-boot-env INIC_MAC_ADDR)
+               rt2x00_eeprom_extract "factory" 0 512
+               rt2x00_eeprom_set_macaddr $wifi_mac
                ;;
-
        *)
-               rt2x00_eeprom_die "board $board is not supported yet"
+               rt2x00_eeprom_die "Please define mtd-eeprom in $board DTS file!"
                ;;
        esac
        ;;