ipq806x: add support for GL.iNet GL-B1300
authorDongming Han <handongming@gl-inet.com>
Thu, 7 Dec 2017 12:48:19 +0000 (20:48 +0800)
committerJohn Crispin <john@phrozen.org>
Wed, 14 Feb 2018 08:40:32 +0000 (09:40 +0100)
This patch adds support for GL.iNet GL-B1300

Specification:
- SOC:        IPQ4028 / QCA Dakota
- RAM:        256 MiB
- FLASH:      32 MiB
- ETH:        Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB:        1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1:      Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2:      Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT:      one reset and one WPS button
- LEDS:       3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART:       1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1

Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
  192.168.1.2 have that file.
- the wifi led will be flashing when writing image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
package/firmware/ipq-wifi/Makefile
package/firmware/ipq-wifi/board-glinet_gl-b1300.bin [new file with mode: 0644]
target/linux/ipq806x/base-files/etc/board.d/01_leds
target/linux/ipq806x/base-files/etc/board.d/02_network
target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq4019-gl-b1300.dts [new file with mode: 0644]
target/linux/ipq806x/image/Makefile
target/linux/ipq806x/patches-4.9/0069-arm-boot-add-dts-files.patch

index 9bb7428..cc29d32 100644 (file)
@@ -13,7 +13,7 @@ endef
 define Build/Compile
 endef
 
-ALLWIFIBOARDS:=avm_fritzbox-4040
+ALLWIFIBOARDS:=avm_fritzbox-4040 glinet_gl-b1300
 ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
 
 define Package/ipq-wifi-default
@@ -48,5 +48,6 @@ Don't install it for any other device!
 endef
 
 $(eval $(call generate-ipq-wifi-package,avm_fritzbox-4040,board-avm_fritzbox-4040.bin,AVM FRITZ!Box 4040))
+$(eval $(call generate-ipq-wifi-package,glinet_gl-b1300,board-glinet_gl-b1300.bin,GL.iNet GL-B1300))
 
 $(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))
diff --git a/package/firmware/ipq-wifi/board-glinet_gl-b1300.bin b/package/firmware/ipq-wifi/board-glinet_gl-b1300.bin
new file mode 100644 (file)
index 0000000..f2020f6
Binary files /dev/null and b/package/firmware/ipq-wifi/board-glinet_gl-b1300.bin differ
index b04832f..ea8b781 100755 (executable)
@@ -16,6 +16,9 @@ avm,fritzbox-4040)
        ucidef_set_led_netdev "wan" "WAN" "fritz4040:green:wan" "eth1"
        ucidef_set_led_switch "lan" "LAN" "fritz4040:green:lan" "switch0" "0x1e"
        ;;
+glinet,gl-b1300)
+       ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
+       ;;
 netgear,d7800 |\
 netgear,r7500 |\
 netgear,r7500v2 |\
index 580c1d8..74223e5 100755 (executable)
@@ -33,6 +33,7 @@ tplink,vr2600v)
        ucidef_add_switch "switch0" \
                "1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
        ;;
+glinet,gl-b1300 |\
 openmesh,a42)
        ucidef_set_interfaces_lan_wan "eth1" "eth0"
        ;;
index 61b7403..fa8eb11 100644 (file)
@@ -53,6 +53,7 @@ case "$FIRMWARE" in
        openmesh,a42)
                ath10kcal_extract "0:ART" 4096 12064
                ;;
+       glinet,gl-b1300 |\
        qcom,ap-dk01.1-c1)
                ath10kcal_extract "ART" 4096 12064
                ;;
@@ -66,6 +67,7 @@ case "$FIRMWARE" in
        openmesh,a42)
                ath10kcal_extract "0:ART" 20480 12064
                ;;
+       glinet,gl-b1300 |\
        qcom,ap-dk01.1-c1)
                ath10kcal_extract "ART" 20480 12064
                ;;
diff --git a/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq4019-gl-b1300.dts b/target/linux/ipq806x/files-4.9/arch/arm/boot/dts/qcom-ipq4019-gl-b1300.dts
new file mode 100644 (file)
index 0000000..53824e3
--- /dev/null
@@ -0,0 +1,316 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+       model = "GL.iNet GL-B1300";
+       compatible = "glinet,gl-b1300", "qcom,ipq4019";
+
+       memory {
+               device_type = "memory";
+               reg = <0x80000000 0x10000000>;
+       };
+
+       reserved-memory {
+               #address-cells = <0x1>;
+               #size-cells = <0x1>;
+               ranges;
+
+               apps_bl@87000000 {
+                       reg = <0x87000000 0x400000>;
+                       no-map;
+               };
+
+               sbl@87400000 {
+                       reg = <0x87400000 0x100000>;
+                       no-map;
+               };
+
+               cnss_debug@87500000 {
+                       reg = <0x87500000 0x600000>;
+                       no-map;
+               };
+
+               cpu_context_dump@87b00000 {
+                       reg = <0x87b00000 0x080000>;
+                       no-map;
+               };
+
+               tz_apps@87b80000 {
+                       reg = <0x87b80000 0x280000>;
+                       no-map;
+               };
+
+               smem@87e00000 {
+                       reg = <0x87e00000 0x080000>;
+                       no-map;
+               };
+
+               tz@87e80000 {
+                       reg = <0x87e80000 0x180000>;
+                       no-map;
+               };
+       };
+
+       soc {
+               tcsr@194b000 {
+                       /* select hostmode */
+                       compatible = "qcom,tcsr";
+                       reg = <0x194b000 0x100>;
+                       qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+                       status = "ok";
+               };
+
+               ess_tcsr@1953000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1953000 0x1000>;
+                       qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+               };
+
+               tcsr@1949000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1949000 0x100>;
+                       qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+               };
+
+               tcsr@1957000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1957000 0x100>;
+                       qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+               };
+
+               pinctrl@1000000 {
+                       serial_pins: serial_pinmux {
+                               mux {
+                                       pins = "gpio60", "gpio61";
+                                       function = "blsp_uart0";
+                                       bias-disable;
+                               };
+                       };
+
+                       spi_0_pins: spi_0_pinmux {
+                               pinmux {
+                                       function = "blsp_spi0";
+                                       pins = "gpio55", "gpio56", "gpio57";
+                               };
+                               pinmux_cs {
+                                       function = "gpio";
+                                       pins = "gpio54";
+                               };
+                               pinconf {
+                                       pins = "gpio55", "gpio56", "gpio57";
+                                       drive-strength = <12>;
+                                       bias-disable;
+                               };
+                               pinconf_cs {
+                                       pins = "gpio54";
+                                       drive-strength = <2>;
+                                       bias-disable;
+                                       output-high;
+                               };
+                       };
+               };
+
+               blsp_dma: dma@7884000 {
+                       status = "ok";
+               };
+
+               spi_0: spi@78b5000 {
+                       pinctrl-0 = <&spi_0_pins>;
+                       pinctrl-names = "default";
+                       status = "ok";
+                       cs-gpios = <&tlmm 54 0>;
+               };
+
+               serial@78af000 {
+                       pinctrl-0 = <&serial_pins>;
+                       pinctrl-names = "default";
+                       status = "ok";
+               };
+
+               cryptobam: dma@8e04000 {
+                       status = "ok";
+               };
+
+               crypto@8e3a000 {
+                       status = "ok";
+               };
+
+               watchdog@b017000 {
+                       status = "ok";
+               };
+
+               usb3_ss_phy: ssphy@9a000 {
+                       status = "ok";
+               };
+
+               usb3_hs_phy: hsphy@a6000 {
+                       status = "ok";
+               };
+
+               usb3: usb3@8af8800 {
+                       status = "ok";
+               };
+
+               usb2_hs_phy: hsphy@a8000 {
+                       status = "ok";
+               };
+
+               usb2: usb2@60f8800 {
+                       status = "ok";
+               };
+
+               mdio@90000 {
+                       status = "okay";
+               };
+
+               ess-switch@c000000 {
+                       status = "okay";
+               };
+
+               ess-psgmii@98000 {
+                       status = "okay";
+               };
+
+               edma@c080000 {
+                       status = "okay";
+               };
+
+               wifi@a000000 {
+                       status = "okay";
+               };
+
+               wifi@a800000 {
+                       status = "okay";
+               };
+       };
+
+       gpio-keys {
+               compatible = "gpio-keys";
+
+               wps {
+                       label = "wps";
+                       gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
+               };
+               reset {
+                       label = "reset";
+                       gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+               };
+       };
+
+       gpio-leds {
+               compatible = "gpio-leds";
+
+               power {
+                       label = "gl-b1300:green:power";
+                       gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+                       default-state = "on";
+               };
+               mesh {
+                       label = "gl-b1300:green:mesh";
+                       gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+               };
+               wlan {
+                       label = "gl-b1300:green:wlan";
+                       gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+               };
+       };
+};
+
+&spi_0 {
+       mx25l25635f@0 {
+               compatible = "mx25l25635f", "jedec,spi-nor";
+               #address-cells = <1>;
+               #size-cells = <1>;
+               reg = <0>;
+               spi-max-frequency = <24000000>;
+
+               SBL1@0 {
+                       label = "SBL1";
+                       reg = <0x0 0x40000>;
+                       read-only;
+               };
+               MIBIB@40000 {
+                       label = "MIBIB";
+                       reg = <0x40000 0x20000>;
+                       read-only;
+               };
+               QSEE@60000 {
+                       label = "QSEE";
+                       reg = <0x60000 0x60000>;
+                       read-only;
+               };
+               CDT@c0000 {
+                       label = "CDT";
+                       reg = <0xc0000 0x10000>;
+                       read-only;
+               };
+               DDRPARAMS@d0000 {
+                       label = "DDRPARAMS";
+                       reg = <0xd0000 0x10000>;
+                       read-only;
+               };
+               APPSBLENV@e0000 {
+                       label = "APPSBLENV";
+                       reg = <0xe0000 0x10000>;
+                       read-only;
+               };
+               APPSBL@f0000 {
+                       label = "APPSBL";
+                       reg = <0xf0000 0x80000>;
+                       read-only;
+               };
+               ART@170000 {
+                       label = "ART";
+                       reg = <0x170000 0x10000>;
+                       read-only;
+               };
+               kernel@180000 {
+                       label = "kernel";
+                       reg = <0x180000 0x400000>;
+               };
+               rootfs@580000 {
+                       label = "rootfs";
+                       reg = <0x580000 0x1a80000>;
+               };
+               firmware@180000 {
+                       label = "firmware";
+                       reg = <0x180000 0x1e80000>;
+               };
+       };
+};
+
+&gmac0 {
+       qcom,phy_mdio_addr = <4>;
+       qcom,poll_required = <1>;
+       qcom,forced_speed = <1000>;
+       qcom,forced_duplex = <1>;
+       vlan_tag = <2 0x20>;
+};
+
+&gmac1 {
+       qcom,phy_mdio_addr = <3>;
+       qcom,poll_required = <1>;
+       qcom,forced_speed = <1000>;
+       qcom,forced_duplex = <1>;
+       vlan_tag = <1 0x10>;
+};
\ No newline at end of file
index 1cae7a5..c2d7255 100644 (file)
@@ -165,6 +165,21 @@ define Device/netgear_r7800
 endef
 TARGET_DEVICES += netgear_r7800
 
+define Device/glinet_gl-b1300
+       DEVICE_TITLE := GL.iNet GL-B1300
+       BOARD_NAME := gl-b1300
+       DEVICE_DTS := qcom-ipq4019-gl-b1300
+       KERNEL_LOADADDR := 0x80208000
+       KERNEL_INSTALL := 1
+       KERNEL_SIZE := 4096k
+       IMAGE_SIZE := 26624k
+       $(call Device/FitImage)
+       IMAGES := sysupgrade.bin
+       IMAGE/sysupgrade.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
+       DEVICE_PACKAGES := ipq-wifi-glinet_gl-b1300
+endef
+TARGET_DEVICES += glinet_gl-b1300
+
 define Device/openmesh_a42
        $(call Device/FitImageLzma)
        DEVICE_DTS := qcom-ipq4019-a42
index faabc24..0f3b20e 100644 (file)
@@ -10,11 +10,12 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -616,9 +616,19 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -616,9 +616,20 @@ dtb-$(CONFIG_ARCH_QCOM) += \
        qcom-apq8074-dragonboard.dtb \
        qcom-apq8084-ifc6540.dtb \
        qcom-apq8084-mtp.dtb \
 +      qcom-ipq4019-a42.dtb \
++      qcom-ipq4019-gl-b1300.dtb \
        qcom-ipq4019-ap.dk01.1-c1.dtb \
        qcom-ipq4019-ap.dk04.1-c1.dtb \
 +      qcom-ipq4019-fritz4040.dtb \