ramips: add support for ELECOM WRC-1167FS
authorINAGAKI Hiroshi <musashino.open@gmail.com>
Fri, 13 Sep 2019 15:14:36 +0000 (00:14 +0900)
committerAdrian Schmutzler <freifunk@adrianschmutzler.de>
Thu, 11 Feb 2021 15:37:53 +0000 (16:37 +0100)
ELECOM WRC-1167FS is a 2.4/5 GHz band 11ac (WiFi-5) router, based on
MT7628AN.

Specification:

- SoC : MediaTek MT7628AN
- RAM : DDR2 64 MiB (NT5TU32M16FG-AC)
- Flash : SPI-NOR 16 MiB (W25Q128JVSIQ)
- WLAN : 2.4/5 GHz 2T2R
  - 2.4 GHz : MediaTek MT7628AN (SoC)
  - 5 GHz : MediaTek MT7612E
- Ethernet : 10/100 Mbps x2
  - Switch : MT7628AN (SoC)
- LEDs/Keys : 6x, 3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
  - J1: 3.3V, GND, TX, RX from "J1" marking
  - 57600n8
- Power : 12 VDC, 1 A

Flash instruction using factory image:

1. Boot WRC-1167FS normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button to
   perform firmware update
4. Wait ~120 seconds to complete flashing

Notes:

- Last 0x800000 (8 MiB) in SPI-NOR flash is not used on stock firmware

- Additional padding in factory image is required to avoid incomplete
  flashing on stock firmware

MAC addresses:

- LAN : BC:5C:4C:xx:xx:68 (Config, ethaddr (text) / Factory, 0x28   (hex))
- WAN : BC:5C:4C:xx:xx:69 (Config, wanaddr (text) / Factory, 0x22   (hex))
- 2.4GHz: BC:5C:4C:xx:xx:6A (Config, rmac    (text) / Factory, 0x4    (hex))
- 5GHz : BC:5C:4C:xx:xx:6B (Config, rmac2   (text) / Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
target/linux/ramips/dts/mt7628an_elecom_wrc-1167fs.dts [new file with mode: 0644]
target/linux/ramips/image/mt76x8.mk
target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
target/linux/ramips/mt76x8/base-files/etc/board.d/02_network

diff --git a/target/linux/ramips/dts/mt7628an_elecom_wrc-1167fs.dts b/target/linux/ramips/dts/mt7628an_elecom_wrc-1167fs.dts
new file mode 100644 (file)
index 0000000..aa60b8a
--- /dev/null
@@ -0,0 +1,164 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7628an.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       compatible = "elecom,wrc-1167fs", "mediatek,mt7628an-soc";
+       model = "ELECOM WRC-1167FS";
+
+       aliases {
+               led-boot = &led_power;
+               led-failsafe = &led_power;
+               led-running = &led_power;
+               led-upgrade = &led_power;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_power: power {
+                       label = "green:power";
+                       gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+               };
+
+               wlan5g {
+                       label = "green:wlan5g";
+                       gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy1tpt";
+               };
+
+               wps {
+                       label = "red:wps";
+                       gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
+               };
+
+               internet {
+                       label = "green:internet";
+                       gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
+               };
+
+               lan {
+                       label = "green:lan";
+                       gpios = <&gpio 40 GPIO_ACTIVE_LOW>;
+               };
+
+               wlan2g {
+                       label = "green:wlan2g";
+                       gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy0tpt";
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               ap {
+                       label = "ap";
+                       gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+                       linux,code = <BTN_0>;
+                       linux,input-type = <EV_SW>;
+               };
+
+               reset {
+                       label = "reset";
+                       gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+               };
+
+               wps {
+                       label = "wps";
+                       gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
+               };
+       };
+};
+
+&spi0 {
+       status = "okay";
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <40000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "u-boot";
+                               reg = <0x0 0x30000>;
+                               read-only;
+                       };
+
+                       partition@30000 {
+                               label = "u-boot-env";
+                               reg = <0x30000 0x10000>;
+                               read-only;
+                       };
+
+                       factory: partition@40000 {
+                               label = "factory";
+                               reg = <0x40000 0x10000>;
+                               read-only;
+                       };
+
+                       partition@50000 {
+                               compatible = "denx,uimage";
+                               label = "firmware";
+                               reg = <0x50000 0x730000>;
+                       };
+
+                       partition@780000 {
+                               label = "storage";
+                               reg = <0x780000 0x80000>;
+                               read-only;
+                       };
+               };
+       };
+};
+
+&ehci {
+       status = "disabled";
+};
+
+&esw {
+       mediatek,portmap = <0x2f>;
+       mediatek,portdisable = <0x27>;
+};
+
+&ethernet {
+       mtd-mac-address = <&factory 0x28>;
+};
+
+&ohci {
+       status = "disabled";
+};
+
+&pcie {
+       status = "okay";
+};
+
+&pcie0 {
+       wifi@0,0 {
+               compatible = "mediatek,mt76";
+               reg = <0x0000 0 0 0 0>;
+               mediatek,mtd-eeprom = <&factory 0x8000>;
+               ieee80211-freq-limit = <5000000 6000000>;
+       };
+};
+
+&state_default {
+       gpio {
+               groups = "wled_an", "p3led_an", "p4led_an", "wdt", "refclk", "i2c", "i2s";
+               function = "gpio";
+       };
+};
+
+&wmac {
+       status = "okay";
+};
index 00976f6..7ba2aca 100644 (file)
@@ -6,6 +6,21 @@ include ./common-tp-link.mk
 
 DEFAULT_SOC := mt7628an
 
+define Build/elecom-header
+       $(eval model_id=$(1))
+       ( \
+               fw_size="$$(printf '%08x' $$(stat -c%s $@))"; \
+               echo -ne "$$(echo "031d6129$${fw_size}06000000$(model_id)" | \
+                       sed 's/../\\x&/g')"; \
+               dd if=/dev/zero bs=92 count=1; \
+               data_crc="$$(dd if=$@ | gzip -c | tail -c 8 | \
+                       od -An -N4 -tx4 --endian little | tr -d ' \n')"; \
+               echo -ne "$$(echo "$${data_crc}00000000" | sed 's/../\\x&/g')"; \
+               dd if=$@; \
+       ) > $@.new
+       mv $@.new $@
+endef
+
 define Build/ravpower-wd009-factory
        mkimage -A mips -T standalone -C none -a 0x80010000 -e 0x80010000 \
                -n "OpenWrt Bootloader" -d $(UBOOT_PATH) $@.new
@@ -93,6 +108,18 @@ define Device/duzun_dm06
 endef
 TARGET_DEVICES += duzun_dm06
 
+define Device/elecom_wrc-1167fs
+  IMAGE_SIZE := 7360k
+  DEVICE_VENDOR := ELECOM
+  DEVICE_MODEL := WRC-1167FS
+  IMAGES += factory.bin
+  IMAGE/factory.bin := $$(sysupgrade_bin) | pad-to 64k | check-size | \
+       xor-image -p 29944A25 -x | elecom-header 00228000 | \
+       elecom-product-header WRC-1167FS
+  DEVICE_PACKAGES := kmod-mt76x2
+endef
+TARGET_DEVICES += elecom_wrc-1167fs
+
 define Device/glinet_gl-mt300n-v2
   IMAGE_SIZE := 16064k
   DEVICE_VENDOR := GL.iNet
index bcbc2ed..47b73e0 100755 (executable)
@@ -25,6 +25,10 @@ cudy,wr1000)
        ucidef_set_led_switch "lan1" "lan1" "blue:lan1" "switch0" "0x08"
        ucidef_set_led_switch "lan2" "lan2" "blue:lan2" "switch0" "0x04"
        ;;
+elecom,wrc-1167fs)
+       ucidef_set_led_switch "lan" "lan" "green:lan" "switch0" "0x8"
+       ucidef_set_led_switch "internet" "internet" "green:internet" "switch0" "0x10"
+       ;;
 glinet,gl-mt300n-v2)
        ucidef_set_led_netdev "wifi_led" "wifi" "red:wlan" "wlan0"
        ucidef_set_led_switch "wan" "wan" "green:wan" "switch0" "0x1"
index 8bbcbb2..b741b4f 100755 (executable)
@@ -46,6 +46,7 @@ ramips_setup_interfaces()
                        "0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0"
                ;;
        buffalo,wcr-1166ds|\
+       elecom,wrc-1167fs|\
        wavlink,wl-wn577a2)
                ucidef_add_switch "switch0" \
                        "3:lan" "4:wan" "6@eth0"
@@ -181,6 +182,10 @@ ramips_setup_macs()
        zyxel,keenetic-extra-ii)
                wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 0x4)" 1)
                ;;
+       elecom,wrc-1167fs)
+               wan_mac=$(mtd_get_mac_binary factory 0x22)
+               label_mac=$wan_mac
+               ;;
        hilink,hlk-7628n)
                lan_mac=$(macaddr_setbit_la "$(cat /sys/class/net/eth0/address)")
                wan_mac=$(macaddr_add "$lan_mac" 1)