ath79: add support for Netgear WNR2000 v3
authorMichal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Wed, 16 Oct 2019 10:41:34 +0000 (12:41 +0200)
committerJohn Crispin <john@phrozen.org>
Mon, 21 Oct 2019 11:15:19 +0000 (13:15 +0200)
This patch adds ath79 support for Netgear WNR2000v3.
Router was previously supported by ar71xx target only.
Note: this is a 4_32 device with limited upgrade capabilities.

Specification
=============
  * Description: Netgear WNR2000 v3
  * Loader: U-boot
  * SOC: Atheros AR7241 (360 MHz)
  * RAM: 32 MiB
  * Flash: 4 MiB (SPI NOR)
- U-boot binary: 256 KiB
- U-boot environment: 64 KiB
- Firmware: 3712 KiB
- ART: 64 KiB
  * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
  * Wireless: 2.4 GHz b/g/n (Atheros AR9287)
  * USB: no
  * Buttons:
- Reset
- WiFi (rfkill)
- WPS
  * LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN (blue)
- 4 x LAN (amber/green)
- WPS (green)
  * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
  * Power supply: DC 12V 1A
  * MAC addresses: LAN on case label, WAN +1, WLAN +2

Installation
============
  * TFTP recovery
  * TFTP via U-boot prompt
  * sysupgrade
  * Web interface

Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_tiny=y
CONFIG_TARGET_ath79_tiny_DEVICE_netgear_wnr2000-v3=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
target/linux/ath79/base-files/etc/board.d/01_leds
target/linux/ath79/base-files/etc/board.d/02_network
target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
target/linux/ath79/dts/ar7241_netgear_wnr2000-v3.dts [new file with mode: 0644]
target/linux/ath79/image/tiny-netgear.mk

index 4ea9586..97598ce 100755 (executable)
@@ -111,6 +111,17 @@ glinet,gl-ar300m-lite)
 glinet,gl-x750)
        ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth1"
        ;;
+netgear,wnr2000-v3)
+       ucidef_set_led_netdev "wan-amber" "WAN (amber)" "netgear:amber:wan" "eth0"
+       ucidef_set_led_switch "lan1green" "LAN1 (green)" "netgear:green:lan1" "switch0" "0x02" "0x04"
+       ucidef_set_led_switch "lan2green" "LAN2 (green)" "netgear:green:lan2" "switch0" "0x04" "0x04"
+       ucidef_set_led_switch "lan3green" "LAN3 (green)" "netgear:green:lan3" "switch0" "0x08" "0x04"
+       ucidef_set_led_switch "lan4green" "LAN4 (green)" "netgear:green:lan4" "switch0" "0x10" "0x04"
+       ucidef_set_led_switch "lan1amber" "LAN1 (amber)" "netgear:amber:lan1" "switch0" "0x02" "0x02"
+       ucidef_set_led_switch "lan2amber" "LAN2 (amber)" "netgear:amber:lan2" "switch0" "0x04" "0x02"
+       ucidef_set_led_switch "lan3amber" "LAN3 (amber)" "netgear:amber:lan3" "switch0" "0x08" "0x02"
+       ucidef_set_led_switch "lan4amber" "LAN4 (amber)" "netgear:amber:lan4" "switch0" "0x10" "0x02"
+       ;;
 netgear,wnr612-v2|\
 on,n150r)
        ucidef_set_led_netdev "wan" "WAN" "netgear:green:wan" "eth0"
index 8e746d3..5b50a62 100755 (executable)
@@ -205,6 +205,7 @@ ath79_setup_interfaces()
                ucidef_add_switch_port_attr "switch0" 2 led 9
                ucidef_add_switch_port_attr "switch0" 5 led 2
                ;;
+       netgear,wnr2000-v3|\
        netgear,wnr612-v2|\
        on,n150r|\
        tplink,tl-wr740n-v1|\
index 1caba14..96b4fb0 100644 (file)
@@ -79,6 +79,7 @@ case "$FIRMWARE" in
        winchannel,wb2000)
                caldata_extract "art" 0x5000 0x440
                ;;
+       netgear,wnr2000-v3|\
        netgear,wnr612-v2|\
        on,n150r|\
        pcs,cap324|\
diff --git a/target/linux/ath79/dts/ar7241_netgear_wnr2000-v3.dts b/target/linux/ath79/dts/ar7241_netgear_wnr2000-v3.dts
new file mode 100644 (file)
index 0000000..deb031b
--- /dev/null
@@ -0,0 +1,207 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar7241.dtsi"
+
+/ {
+       compatible = "netgear,wnr2000-v3", "qca,ar7241";
+       model = "Netgear WNR2000 v3";
+
+       chosen {
+               bootargs = "console=ttyS0,115200n8";
+       };
+
+       aliases {
+               led-boot = &power_amber;
+               led-failsafe = &power_amber;
+               led-running = &power_green;
+               led-upgrade = &power_amber;
+               label-mac-device = &eth1;
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               wps {
+                       label = "wps";
+                       linux,code = <KEY_WPS_BUTTON>;
+                       gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       ath9k-keys {
+               compatible = "gpio-keys-polled";
+               poll-interval = <20>;
+
+               reset {
+                       label = "reset";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&ath9k 8 GPIO_ACTIVE_LOW>;
+                       debounce-interval = <60>;
+               };
+
+               rfkill {
+                       label = "rfkill";
+                       linux,code = <KEY_RFKILL>;
+                       gpios = <&ath9k 9 GPIO_ACTIVE_LOW>;
+                       debounce-interval = <60>;
+               };
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               pinctrl-names = "default";
+               pinctrl-0 = <&jtag_disable_pins &switch_led_disable_pins &clks_disable_pins>;
+
+               wan_green {
+                       label = "netgear:green:wan";
+                       gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+               };
+
+               wan_amber {
+                       label = "netgear:amber:wan";
+                       gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+               };
+
+               lan1_green {
+                       label = "netgear:green:lan1";
+                       gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+               };
+
+               lan1_amber {
+                       label = "netgear:amber:lan1";
+                       gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+               };
+
+               lan2_green {
+                       label = "netgear:green:lan2";
+                       gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+               };
+
+               lan2_amber {
+                       label = "netgear:amber:lan2";
+                       gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+               };
+
+               lan3_green {
+                       label = "netgear:green:lan3";
+                       gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+               };
+
+               lan3_amber {
+                       label = "netgear:amber:lan3";
+                       gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+               };
+
+               lan4_green {
+                       label = "netgear:green:lan4";
+                       gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+               };
+
+               lan4_amber {
+                       label = "netgear:amber:lan4";
+                       gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+               };
+
+               wps_green {
+                       label = "netgear:green:wps";
+                       gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       ath9k-leds {
+               compatible = "gpio-leds";
+
+               power_green: power_green {
+                       label = "netgear:green:power";
+                       gpios = <&ath9k 3 GPIO_ACTIVE_LOW>;
+               };
+
+               power_amber: power_amber {
+                       label = "netgear:amber:power";
+                       gpios = <&ath9k 2 GPIO_ACTIVE_LOW>;
+                       default-state = "keep";
+               };
+
+               wlan_blue {
+                       label = "netgear:blue:wlan";
+                       gpios = <&ath9k 1 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy0tpt";
+               };
+       };
+};
+
+&spi {
+       status = "okay";
+       num-cs = <1>;
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <25000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "u-boot";
+                               reg = <0x0 0x40000>;
+                               read-only;
+                       };
+
+                       partition@40000 {
+                               label = "u-boot-env";
+                               reg = <0x40000 0x10000>;
+                       };
+
+                       partition@50000 {
+                               label = "firmware";
+                               reg = <0x50000 0x3a0000>;
+                               compatible = "netgear,uimage";
+                       };
+
+                       art: partition@3f0000 {
+                               label = "art";
+                               reg = <0x3f0000 0x10000>;
+                               read-only;
+                       };
+               };
+       };
+};
+
+&eth0 {
+       status = "okay";
+
+       mtd-mac-address = <&art 0x0>;
+};
+
+&eth1 {
+       status = "okay";
+
+       compatible = "qca,ar7241-eth", "syscon", "simple-mfd";
+       mtd-mac-address = <&art 0x6>;
+};
+
+&pcie {
+       status = "okay";
+
+       ath9k: wifi@0,0 {
+               compatible = "pci168c,002e";
+               reg = <0x0000 0 0 0 0>;
+               mtd-mac-address = <&art 0x0>;
+               mtd-mac-address-increment = <1>;
+               qca,no-eeprom;
+               #gpio-cells = <2>;
+               gpio-controller;
+       };
+};
+
+&uart {
+       status = "okay";
+};
index 2f17d79..b5fed1b 100644 (file)
@@ -27,3 +27,19 @@ define Device/on_n150r
   SUPPORTED_DEVICES += n150r
 endef
 TARGET_DEVICES += on_n150r
+
+define Device/netgear_wnr2000-v3
+  ATH_SOC := ar7241
+  DEVICE_MODEL := WNR2000
+  DEVICE_VARIANT := v3
+  NETGEAR_KERNEL_MAGIC := 0x32303033
+  NETGEAR_BOARD_ID := WNR2000V3
+  NETGEAR_HW_ID := 29763551+04+32
+  IMAGE_SIZE := 3712k
+  IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | netgear-squashfs | append-rootfs | pad-rootfs
+  IMAGES += factory-NA.img
+  IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | check-size $$$$(IMAGE_SIZE)
+  SUPPORTED_DEVICES += wnr2000-v3
+  $(Device/netgear_ath79)
+endef
+TARGET_DEVICES += netgear_wnr2000-v3