ar71xx: add support for Nokia WI2A-AC200i
authorFelix Fietkau <nbd@nbd.name>
Tue, 27 Jun 2017 21:26:03 +0000 (23:26 +0200)
committerFelix Fietkau <nbd@nbd.name>
Thu, 19 Oct 2017 10:27:42 +0000 (12:27 +0200)
Specifications:
 - SoC: Qualcomm QCA9558 (720 MHz)
 - RAM: 256MB
 - Storage: 1MB NOR, 128 MB NAND flash
 - Ethernet: 1x1000M

Installation:
 1. Connect to serial console on the board
 2. Boot initramfs image over u-boot
 3. Copy image to the device and run sysupgrade

Installation without serial console is not supported at this time

Signed-off-by: Felix Fietkau <nbd@nbd.name>
14 files changed:
target/linux/ar71xx/base-files/etc/board.d/01_leds
target/linux/ar71xx/base-files/etc/board.d/02_network
target/linux/ar71xx/base-files/etc/diag.sh
target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
target/linux/ar71xx/base-files/lib/ar71xx.sh
target/linux/ar71xx/base-files/lib/upgrade/platform.sh
target/linux/ar71xx/config-4.4
target/linux/ar71xx/config-4.9
target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
target/linux/ar71xx/files/arch/mips/ath79/Makefile
target/linux/ar71xx/files/arch/mips/ath79/mach-wi2a-ac200i.c [new file with mode: 0644]
target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
target/linux/ar71xx/image/nand.mk
target/linux/ar71xx/nand/config-default

index 80d1953..0694fe9 100755 (executable)
@@ -824,6 +824,12 @@ r6100)
        ucidef_set_led_usbdev "usb" "USB" "netgear:blue:usb" "1-1"
        ucidef_set_led_wlan "wlan" "WLAN" "netgear:blue:wlan" "phy1tpt"
        ;;
+wi2a-ac200i)
+       ucidef_set_led_default "power" "Power (green)" "nokia:green:power" "1"
+       ucidef_set_led_default "wan" "Ethernet LED (green)" "nokia:green:wan" "1"
+       ucidef_set_led_wlan "wlan5g" "WLAN" "nokia:green:wlan-5g" "phy0tpt"
+       ucidef_set_led_wlan "wlan2g" "WLAN" "nokia:green:wlan-2g" "phy1tpt"
+       ;;
 wndr3700v4|\
 wndr4300)
        ucidef_set_led_switch "wan-green" "WAN (green)" "netgear:green:wan" "switch0" "0x20" "0x08"
index d838352..46b2171 100755 (executable)
@@ -128,6 +128,7 @@ ar71xx_setup_interfaces()
        tl-wr902ac-v1|\
        tube2h|\
        unifiac-lite|\
+       wi2a-ac200i|\
        wndap360|\
        wp543)
                ucidef_set_interface_lan "eth0"
index ade726f..7fa4ff0 100644 (file)
@@ -459,6 +459,9 @@ get_status_led() {
        airgatewaypro)
                status_led="ubnt:white:status"
                ;;
+       wi2a-ac200i)
+               status_led="nokia:green:ctrl"
+               ;;
        whr-g301n|\
        whr-hp-g300n|\
        whr-hp-gn|\
@@ -529,6 +532,9 @@ set_state() {
                        local n=$(fw_printenv activeregion | cut -d = -f 2)
                        fw_setenv "image${n}trynum" 0
                        ;;
+               wi2a-ac200i)
+                       fw_setenv PKRstCnt 0
+                       ;;
                esac
                ;;
        esac
index 85a2a63..9a5f82b 100644 (file)
@@ -111,6 +111,9 @@ case "$FIRMWARE" in
        unifiac-pro)
                ath10kcal_extract "EEPROM" 20480 2116
                ;;
+       wi2a-ac200i)
+               ath10kcal_extract "ART" 20480 2116
+               ;;
        esac
        ;;
 "ath10k/cal-pci-0000:01:00.0.bin")
index 835ced6..9298451 100755 (executable)
@@ -1231,6 +1231,9 @@ ar71xx_board_detect() {
        "WeIO"*)
                name="weio"
                ;;
+       *"WI2A-AC200i")
+               name="wi2a-ac200i"
+               ;;
        *"WHR-G301N")
                name="whr-g301n"
                ;;
index 778faed..97d5601 100755 (executable)
@@ -534,6 +534,7 @@ platform_check_image() {
        nbg6716|\
        r6100|\
        rambutan|\
+       wi2a-ac200i|\
        wndr3700v4|\
        wndr4300)
                nand_do_platform_check $board $1
@@ -708,6 +709,7 @@ platform_pre_upgrade() {
        rb-2011uias-2hnd|\
        rb-sxt2n|\
        rb-sxt5n|\
+       wi2a-ac200i|\
        wndr3700v4|\
        wndr4300)
                nand_do_upgrade "$1"
@@ -743,6 +745,23 @@ platform_nand_pre_upgrade() {
                mtd erase kernel
                tar xf "$1" sysupgrade-routerboard/kernel -O | nandwrite -o "$fw_mtd" -
                ;;
+       wi2a-ac200i)
+               case "$(fw_printenv -n dualPartition)" in
+                       imgA)
+                               fw_setenv dualPartition imgB
+                               fw_setenv ActImg NokiaImageB
+                       ;;
+                       imgB)
+                               fw_setenv dualPartition imgA
+                               fw_setenv ActImg NokiaImageA
+                       ;;
+               esac
+               ubiblock -r /dev/ubiblock0_0 2>/dev/null >/dev/null
+               rm -f /dev/ubiblock0_0
+               ubidetach -d 0 2>/dev/null >/dev/null
+               CI_UBIPART=ubi_alt
+               CI_KERNPART=kernel_alt
+               ;;
        esac
 }
 
index 0e77560..4793bf4 100644 (file)
@@ -223,6 +223,7 @@ CONFIG_ATH79_MACH_UBNT=y
 CONFIG_ATH79_MACH_UBNT_UNIFIAC=y
 CONFIG_ATH79_MACH_UBNT_XM=y
 CONFIG_ATH79_MACH_WEIO=y
+# CONFIG_ATH79_MACH_WI2A_AC200I is not set
 CONFIG_ATH79_MACH_WHR_HP_G300N=y
 CONFIG_ATH79_MACH_WLAE_AG300N=y
 CONFIG_ATH79_MACH_WLR8100=y
index c5b8908..84b2a0b 100644 (file)
@@ -221,6 +221,7 @@ CONFIG_ATH79_MACH_UBNT=y
 CONFIG_ATH79_MACH_UBNT_UNIFIAC=y
 CONFIG_ATH79_MACH_UBNT_XM=y
 CONFIG_ATH79_MACH_WEIO=y
+# CONFIG_ATH79_MACH_WI2A_AC200I is not set
 CONFIG_ATH79_MACH_WHR_HP_G300N=y
 CONFIG_ATH79_MACH_WLAE_AG300N=y
 CONFIG_ATH79_MACH_WLR8100=y
index 454aee6..0b5bae6 100644 (file)
@@ -8,6 +8,17 @@ config ATH79_MACH_A60
        select ATH79_DEV_WMAC
        select ATH79_DEV_USB
 
+config ATH79_MACH_WI2A_AC200I
+       bool "Nokia WI2A-AC200i support"
+       select SOC_QCA955X
+       select ATH79_DEV_ETH
+       select ATH79_DEV_GPIO_BUTTONS
+       select ATH79_DEV_LEDS_GPIO
+       select ATH79_DEV_M25P80
+       select ATH79_DEV_NFC
+       select ATH79_DEV_WMAC
+       select ATH79_DEV_USB
+
 config ATH79_MACH_ALFA_AP120C
        bool "ALFA Network AP120C board support"
        select ATH79_DEV_AP9X_PCI if PCI
index 0975aac..a8d9dda 100644 (file)
@@ -39,6 +39,7 @@ obj-$(CONFIG_ATH79_ROUTERBOOT)                += routerboot.o
 # Machines
 #
 obj-$(CONFIG_ATH79_MACH_A60)                   += mach-a60.o
+obj-$(CONFIG_ATH79_MACH_WI2A_AC200I)           += mach-wi2a-ac200i.o
 obj-$(CONFIG_ATH79_MACH_ALFA_AP120C)           += mach-alfa-ap120c.o
 obj-$(CONFIG_ATH79_MACH_ALFA_AP96)             += mach-alfa-ap96.o
 obj-$(CONFIG_ATH79_MACH_ALFA_NX)               += mach-alfa-nx.o
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-wi2a-ac200i.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-wi2a-ac200i.c
new file mode 100644 (file)
index 0000000..85e0c8f
--- /dev/null
@@ -0,0 +1,217 @@
+/*
+ * Nokia WI2A-AC200i support
+ *
+ * Copyright (c) 2012 Qualcomm Atheros
+ * Copyright (c) 2012-2013 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (c) 2017 Felix Fietkau <nbd@nbd.name>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/platform/ar934x_nfc.h>
+
+#include <asm/mach-ath79/ar71xx_regs.h>
+#include <asm/fw/fw.h>
+
+#include "common.h"
+#include "pci.h"
+#include "dev-ap9x-pci.h"
+#include "dev-gpio-buttons.h"
+#include "dev-eth.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-nfc.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+
+#define AC200I_GPIO_BTN_RESET          17
+
+#define AC200I_KEYS_POLL_INTERVAL      20      /* msecs */
+#define AC200I_KEYS_DEBOUNCE_INTERVAL  (3 * AC200I_KEYS_POLL_INTERVAL)
+
+#define AC200I_MAC_ADDR                        0x1f040249
+#define AC200I_MAC1_OFFSET             6
+#define AC200I_WMAC_CALDATA_ADDR       0x1f061000
+
+static struct gpio_led ac200i_leds_gpio[] __initdata = {
+       {
+               .name           = "nokia:red:wlan-2g",
+               .gpio           = 0,
+               .active_low     = 1,
+       },
+       {
+               .name           = "nokia:green:power",
+               .gpio           = 1,
+               .active_low     = 1,
+       },
+       {
+               .name           = "nokia:green:wlan-2g",
+               .gpio           = 2,
+               .active_low     = 1,
+       },
+       {
+               .name           = "nokia:green:ctrl",
+               .gpio           = 3,
+               .active_low     = 1,
+       },
+       {
+               .name           = "nokia:green:eth",
+               .gpio           = 4,
+               .active_low     = 1,
+       },
+       {
+               .name           = "nokia:red:power",
+               .gpio           = 13,
+               .active_low     = 1,
+       },
+       {
+               .name           = "nokia:red:eth",
+               .gpio           = 14,
+               .active_low     = 1,
+       },
+       {
+               .name           = "nokia:red:wlan-5g",
+               .gpio           = 18,
+               .active_low     = 1,
+       },
+       {
+               .name           = "nokia:green:wlan-5g",
+               .gpio           = 19,
+               .active_low     = 1,
+       },
+       {
+               .name           = "nokia:red:ctrl",
+               .gpio           = 20,
+               .active_low     = 1,
+       },
+};
+
+static struct gpio_keys_button ac200i_gpio_keys[] __initdata = {
+       {
+               .desc           = "Reset button",
+               .type           = EV_KEY,
+               .code           = KEY_RESTART,
+               .debounce_interval = AC200I_KEYS_DEBOUNCE_INTERVAL,
+               .gpio           = AC200I_GPIO_BTN_RESET,
+               .active_low     = 1,
+       },
+};
+
+static struct mtd_partition ac200i_nand_partitions[] = {
+       {
+               .name   = "cfg",
+               .offset = 0x0100000,
+               .size   = 0x1800000,
+               .mask_flags = MTD_WRITEABLE,
+       },
+       {
+               .name   = "kernel",
+               .offset = 0x2000000,
+               .size   = 0x0400000,
+       },
+       {
+               .name   = "ubi",
+               .offset = 0x2400000,
+               .size   = 0x2000000,
+       },
+       {
+               .name   = "kernel",
+               .offset = 0x5000000,
+               .size   = 0x0400000,
+       },
+       {
+               .name   = "ubi",
+               .offset = 0x5400000,
+               .size   = 0x2000000,
+       },
+};
+
+static const char *boot_getenv(const char *key)
+{
+       const char *start = (const char *) KSEG1ADDR(0x1f070000);
+       const char *end = start + 0x20000;
+       const char *addr;
+
+       for (addr = start + 4;
+            *addr && *addr != 0xff && addr < end &&
+            strnlen(addr, end - addr) < end - addr;
+            addr += strnlen(addr, end - addr) + 1) {
+               const char *val;
+
+               val = strchr(addr, '=');
+               if (!val)
+                       continue;
+
+               if (strncmp(addr, key, val - addr))
+                       continue;
+
+               return val + 1;
+       }
+       return NULL;
+}
+
+static void __init ac200i_setup(void)
+{
+       const char *img;
+       u8 *wmac = (u8 *) KSEG1ADDR(AC200I_WMAC_CALDATA_ADDR);
+       u8 *mac_addr = (u8 *) KSEG1ADDR(AC200I_MAC_ADDR);
+
+       ath79_register_m25p80(NULL);
+
+       ath79_register_leds_gpio(-1, ARRAY_SIZE(ac200i_leds_gpio),
+                                ac200i_leds_gpio);
+       ath79_register_gpio_keys_polled(-1, AC200I_KEYS_POLL_INTERVAL,
+                                       ARRAY_SIZE(ac200i_gpio_keys),
+                                       ac200i_gpio_keys);
+
+       ath79_register_usb();
+       ath79_nfc_set_parts(ac200i_nand_partitions,
+                           ARRAY_SIZE(ac200i_nand_partitions));
+       ath79_nfc_set_ecc_mode(AR934X_NFC_ECC_HW);
+       ath79_register_nfc();
+
+       ath79_register_wmac(wmac, NULL);
+
+       ath79_register_mdio(0, 0x0);
+       ath79_init_mac(ath79_eth0_data.mac_addr, mac_addr, 0);
+
+       /* GMAC0 is connected to the SGMII interface */
+       ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
+       ath79_eth0_data.phy_mask = BIT(4);
+       ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+       ath79_eth0_pll_data.pll_1000 = 0x03000101;
+       ath79_eth0_pll_data.pll_100 = 0x80000101;
+       ath79_eth0_pll_data.pll_10 = 0x80001313;
+
+       img = boot_getenv("dualPartition");
+       if (img && !strcmp(img, "imgA")) {
+               ac200i_nand_partitions[3].name = "kernel_alt";
+               ac200i_nand_partitions[4].name = "ubi_alt";
+       } else {
+               ac200i_nand_partitions[1].name = "kernel_alt";
+               ac200i_nand_partitions[2].name = "ubi_alt";
+       }
+
+       ath79_register_eth(0);
+
+       ath79_register_pci();
+}
+
+MIPS_MACHINE(ATH79_MACH_WI2A_AC200I, "WI2A-AC200i",
+            "Nokia WI2A-AC200i",
+            ac200i_setup);
index 756d406..c75ff4f 100644 (file)
@@ -19,6 +19,7 @@ enum ath79_mach_type {
        ATH79_MACH_GENERIC = 0,
        ATH79_MACH_A40,                         /* OpenMesh A40 */
        ATH79_MACH_A60,                         /* OpenMesh A60 */
+       ATH79_MACH_WI2A_AC200I,                 /* Nokia WI2A-AC200i */
        ATH79_MACH_ALFA_AP120C,                 /* ALFA Network AP120C board */
        ATH79_MACH_ALFA_AP96,                   /* ALFA Network AP96 board */
        ATH79_MACH_ALFA_NX,                     /* ALFA Network N2/N5 board */
index fafccb9..ba9e1ba 100644 (file)
@@ -84,6 +84,21 @@ define Device/rambutan
 endef
 TARGET_DEVICES += rambutan
 
+define Device/wi2a-ac200i
+  SUPPORTED_DEVICES = $(1)
+  DEVICE_TITLE := Nokia WI2A-AC200i
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath9k kmod-ath10k ath10k-firmware-qca988x
+  BOARDNAME := WI2A-AC200i
+  BLOCKSIZE := 64k
+  KERNEL_SIZE := 3648k
+  IMAGE_SIZE := 32m
+  IMAGES := sysupgrade.tar
+  MTDPARTS := spi0.0:256k(u-boot)ro,64k(envFacA)ro,64k(envFacB)ro,64k(ART)ro,128k(u-boot-env)
+  KERNEL := kernel-bin | patch-cmdline | lzma | uImage lzma
+  IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
+endef
+TARGET_DEVICES += wi2a-ac200i
+
 define Device/z1
   DEVICE_TITLE := Meraki Z1
   DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport kmod-spi-gpio kmod-ath9k kmod-owl-loader
index fc243c5..340d64c 100644 (file)
@@ -180,6 +180,7 @@ CONFIG_ATH79_MACH_RAMBUTAN=y
 # CONFIG_ATH79_MACH_UBNT_XM is not set
 # CONFIG_ATH79_MACH_WEIO is not set
 # CONFIG_ATH79_MACH_WHR_HP_G300N is not set
+CONFIG_ATH79_MACH_WI2A_AC200I=y
 # CONFIG_ATH79_MACH_WLAE_AG300N is not set
 # CONFIG_ATH79_MACH_WLR8100 is not set
 # CONFIG_ATH79_MACH_WNDAP360 is not set