+++ /dev/null
-Index: linux-2.6.22.19/arch/arm/boot/compressed/head-at91rm9200.S
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/boot/compressed/head-at91rm9200.S
-+++ linux-2.6.22.19/arch/arm/boot/compressed/head-at91rm9200.S
-@@ -73,6 +73,12 @@
- cmp r7, r3
- beq 99f
-
-+ @ Promwad Chub : 1181
-+ mov r3, #(MACH_TYPE_CHUB & 0xff)
-+ orr r3, r3, #(MACH_TYPE_CHUB & 0xff00)
-+ cmp r7, r3
-+ beq 99f
-+
- @ Unknown board, use the AT91RM9200DK board
- @ mov r7, #MACH_TYPE_AT91RM9200
- mov r7, #(MACH_TYPE_AT91RM9200DK & 0xff)
-Index: linux-2.6.22.19/arch/arm/configs/at91sam9260ek_defconfig
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/configs/at91sam9260ek_defconfig
-+++ linux-2.6.22.19/arch/arm/configs/at91sam9260ek_defconfig
-@@ -1,18 +1,24 @@
- #
- # Automatically generated make config: don't edit
--# Linux kernel version: 2.6.19-rc6
--# Fri Nov 17 18:42:21 2006
-+# Linux kernel version: 2.6.21
-+# Mon May 7 11:42:02 2007
- #
- CONFIG_ARM=y
-+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-+CONFIG_GENERIC_GPIO=y
- # CONFIG_GENERIC_TIME is not set
- CONFIG_MMU=y
-+# CONFIG_NO_IOPORT is not set
- CONFIG_GENERIC_HARDIRQS=y
- CONFIG_TRACE_IRQFLAGS_SUPPORT=y
- CONFIG_HARDIRQS_SW_RESEND=y
- CONFIG_GENERIC_IRQ_PROBE=y
- CONFIG_RWSEM_GENERIC_SPINLOCK=y
-+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
- CONFIG_GENERIC_HWEIGHT=y
- CONFIG_GENERIC_CALIBRATE_DELAY=y
-+CONFIG_ZONE_DMA=y
- CONFIG_VECTORS_BASE=0xffff0000
- CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-@@ -31,13 +37,16 @@ CONFIG_LOCALVERSION=""
- # CONFIG_SWAP is not set
- CONFIG_SYSVIPC=y
- # CONFIG_IPC_NS is not set
-+CONFIG_SYSVIPC_SYSCTL=y
- # CONFIG_POSIX_MQUEUE is not set
- # CONFIG_BSD_PROCESS_ACCT is not set
- # CONFIG_TASKSTATS is not set
- # CONFIG_UTS_NS is not set
- # CONFIG_AUDIT is not set
- # CONFIG_IKCONFIG is not set
-+CONFIG_SYSFS_DEPRECATED=y
- # CONFIG_RELAY is not set
-+CONFIG_BLK_DEV_INITRD=y
- CONFIG_INITRAMFS_SOURCE=""
- CONFIG_CC_OPTIMIZE_FOR_SIZE=y
- CONFIG_SYSCTL=y
-@@ -76,7 +85,9 @@ CONFIG_KMOD=y
- # Block layer
- #
- CONFIG_BLOCK=y
-+# CONFIG_LBD is not set
- # CONFIG_BLK_DEV_IO_TRACE is not set
-+# CONFIG_LSF is not set
-
- #
- # IO Schedulers
-@@ -110,10 +121,12 @@ CONFIG_ARCH_AT91=y
- # CONFIG_ARCH_IMX is not set
- # CONFIG_ARCH_IOP32X is not set
- # CONFIG_ARCH_IOP33X is not set
-+# CONFIG_ARCH_IOP13XX is not set
- # CONFIG_ARCH_IXP4XX is not set
- # CONFIG_ARCH_IXP2000 is not set
- # CONFIG_ARCH_IXP23XX is not set
- # CONFIG_ARCH_L7200 is not set
-+# CONFIG_ARCH_NS9XXX is not set
- # CONFIG_ARCH_PNX4008 is not set
- # CONFIG_ARCH_PXA is not set
- # CONFIG_ARCH_RPC is not set
-@@ -129,21 +142,29 @@ CONFIG_ARCH_AT91=y
- # CONFIG_ARCH_AT91RM9200 is not set
- CONFIG_ARCH_AT91SAM9260=y
- # CONFIG_ARCH_AT91SAM9261 is not set
-+# CONFIG_ARCH_AT91SAM9263 is not set
-+
-+#
-+# AT91SAM9260 Variants
-+#
-+# CONFIG_ARCH_AT91SAM9260_SAM9XE is not set
-
- #
--# AT91SAM9260 Board Type
-+# AT91SAM9260 / AT91SAM9XE Board Type
- #
- CONFIG_MACH_AT91SAM9260EK=y
-
- #
- # AT91 Board Options
- #
-+# CONFIG_MTD_AT91_DATAFLASH_CARD is not set
- # CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set
-
- #
- # AT91 Feature Selections
- #
- # CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set
-+# CONFIG_ATMEL_TCLIB is not set
-
- #
- # Processor Type
-@@ -166,6 +187,7 @@ CONFIG_CPU_CP15_MMU=y
- # CONFIG_CPU_DCACHE_DISABLE is not set
- # CONFIG_CPU_DCACHE_WRITETHROUGH is not set
- # CONFIG_CPU_CACHE_ROUND_ROBIN is not set
-+# CONFIG_OUTER_CACHE is not set
-
- #
- # Bus support
-@@ -193,6 +215,7 @@ CONFIG_FLAT_NODE_MEM_MAP=y
- # CONFIG_SPARSEMEM_STATIC is not set
- CONFIG_SPLIT_PTLOCK_CPUS=4096
- # CONFIG_RESOURCES_64BIT is not set
-+CONFIG_ZONE_DMA_FLAG=1
- # CONFIG_LEDS is not set
- CONFIG_ALIGNMENT_TRAP=y
-
-@@ -203,6 +226,7 @@ CONFIG_ZBOOT_ROM_TEXT=0x0
- CONFIG_ZBOOT_ROM_BSS=0x0
- CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw"
- # CONFIG_XIP_KERNEL is not set
-+# CONFIG_KEXEC is not set
-
- #
- # Floating point emulation
-@@ -228,7 +252,6 @@ CONFIG_BINFMT_ELF=y
- # Power management options
- #
- # CONFIG_PM is not set
--# CONFIG_APM is not set
-
- #
- # Networking
-@@ -242,9 +265,6 @@ CONFIG_NET=y
- CONFIG_PACKET=y
- # CONFIG_PACKET_MMAP is not set
- CONFIG_UNIX=y
--CONFIG_XFRM=y
--# CONFIG_XFRM_USER is not set
--# CONFIG_XFRM_SUB_POLICY is not set
- # CONFIG_NET_KEY is not set
- CONFIG_INET=y
- # CONFIG_IP_MULTICAST is not set
-@@ -263,14 +283,15 @@ CONFIG_IP_PNP_BOOTP=y
- # CONFIG_INET_IPCOMP is not set
- # CONFIG_INET_XFRM_TUNNEL is not set
- # CONFIG_INET_TUNNEL is not set
--CONFIG_INET_XFRM_MODE_TRANSPORT=y
--CONFIG_INET_XFRM_MODE_TUNNEL=y
--CONFIG_INET_XFRM_MODE_BEET=y
-+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-+# CONFIG_INET_XFRM_MODE_BEET is not set
- CONFIG_INET_DIAG=y
- CONFIG_INET_TCP_DIAG=y
- # CONFIG_TCP_CONG_ADVANCED is not set
- CONFIG_TCP_CONG_CUBIC=y
- CONFIG_DEFAULT_TCP_CONG="cubic"
-+# CONFIG_TCP_MD5SIG is not set
- # CONFIG_IPV6 is not set
- # CONFIG_INET6_XFRM_TUNNEL is not set
- # CONFIG_INET6_TUNNEL is not set
-@@ -328,6 +349,7 @@ CONFIG_STANDALONE=y
- CONFIG_PREVENT_FIRMWARE_BUILD=y
- # CONFIG_FW_LOADER is not set
- # CONFIG_DEBUG_DRIVER is not set
-+# CONFIG_DEBUG_DEVRES is not set
- # CONFIG_SYS_HYPERVISOR is not set
-
- #
-@@ -348,6 +370,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
- #
- # Plug and Play support
- #
-+# CONFIG_PNPACPI is not set
-
- #
- # Block devices
-@@ -360,7 +383,6 @@ CONFIG_BLK_DEV_RAM=y
- CONFIG_BLK_DEV_RAM_COUNT=16
- CONFIG_BLK_DEV_RAM_SIZE=8192
- CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
--CONFIG_BLK_DEV_INITRD=y
- # CONFIG_CDROM_PKTCDVD is not set
- # CONFIG_ATA_OVER_ETH is not set
-
-@@ -369,6 +391,7 @@ CONFIG_BLK_DEV_INITRD=y
- #
- # CONFIG_RAID_ATTRS is not set
- CONFIG_SCSI=y
-+# CONFIG_SCSI_TGT is not set
- # CONFIG_SCSI_NETLINK is not set
- CONFIG_SCSI_PROC_FS=y
-
-@@ -388,6 +411,7 @@ CONFIG_BLK_DEV_SD=y
- CONFIG_SCSI_MULTI_LUN=y
- # CONFIG_SCSI_CONSTANTS is not set
- # CONFIG_SCSI_LOGGING is not set
-+# CONFIG_SCSI_SCAN_ASYNC is not set
-
- #
- # SCSI Transports
-@@ -405,6 +429,11 @@ CONFIG_SCSI_MULTI_LUN=y
- # CONFIG_SCSI_DEBUG is not set
-
- #
-+# Serial ATA (prod) and Parallel ATA (experimental) drivers
-+#
-+# CONFIG_ATA is not set
-+
-+#
- # Multi-device support (RAID and LVM)
- #
- # CONFIG_MD is not set
-@@ -425,7 +454,51 @@ CONFIG_SCSI_MULTI_LUN=y
- #
- # Network device support
- #
--# CONFIG_NETDEVICES is not set
-+CONFIG_NETDEVICES=y
-+# CONFIG_DUMMY is not set
-+# CONFIG_BONDING is not set
-+# CONFIG_EQUALIZER is not set
-+# CONFIG_TUN is not set
-+
-+#
-+# PHY device support
-+#
-+# CONFIG_PHYLIB is not set
-+
-+#
-+# Ethernet (10 or 100Mbit)
-+#
-+CONFIG_NET_ETHERNET=y
-+CONFIG_MII=y
-+CONFIG_MACB=y
-+# CONFIG_SMC91X is not set
-+# CONFIG_DM9000 is not set
-+
-+#
-+# Ethernet (1000 Mbit)
-+#
-+
-+#
-+# Ethernet (10000 Mbit)
-+#
-+
-+#
-+# Token Ring devices
-+#
-+
-+#
-+# Wireless LAN (non-hamradio)
-+#
-+# CONFIG_NET_RADIO is not set
-+
-+#
-+# Wan interfaces
-+#
-+# CONFIG_WAN is not set
-+# CONFIG_PPP is not set
-+# CONFIG_SLIP is not set
-+# CONFIG_SHAPER is not set
-+# CONFIG_NETCONSOLE is not set
- # CONFIG_NETPOLL is not set
- # CONFIG_NET_POLL_CONTROLLER is not set
-
-@@ -517,10 +590,6 @@ CONFIG_HW_RANDOM=y
- # CONFIG_NVRAM is not set
- # CONFIG_DTLK is not set
- # CONFIG_R3964 is not set
--
--#
--# Ftape, the floppy tape device driver
--#
- # CONFIG_RAW_DRIVER is not set
-
- #
-@@ -553,7 +622,11 @@ CONFIG_HW_RANDOM=y
- #
- # Misc devices
- #
--# CONFIG_TIFM_CORE is not set
-+
-+#
-+# Multifunction device drivers
-+#
-+# CONFIG_MFD_SM501 is not set
-
- #
- # LED devices
-@@ -582,7 +655,7 @@ CONFIG_HW_RANDOM=y
- #
- # Graphics support
- #
--# CONFIG_FIRMWARE_EDID is not set
-+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
- # CONFIG_FB is not set
-
- #
-@@ -590,7 +663,6 @@ CONFIG_HW_RANDOM=y
- #
- # CONFIG_VGA_CONSOLE is not set
- CONFIG_DUMMY_CONSOLE=y
--# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
- #
- # Sound
-@@ -598,6 +670,12 @@ CONFIG_DUMMY_CONSOLE=y
- # CONFIG_SOUND is not set
-
- #
-+# HID Devices
-+#
-+CONFIG_HID=y
-+# CONFIG_HID_DEBUG is not set
-+
-+#
- # USB support
- #
- CONFIG_USB_ARCH_HAS_HCD=y
-@@ -610,7 +688,6 @@ CONFIG_USB=y
- # Miscellaneous USB options
- #
- CONFIG_USB_DEVICEFS=y
--# CONFIG_USB_BANDWIDTH is not set
- # CONFIG_USB_DYNAMIC_MINORS is not set
- # CONFIG_USB_OTG is not set
-
-@@ -619,7 +696,8 @@ CONFIG_USB_DEVICEFS=y
- #
- # CONFIG_USB_ISP116X_HCD is not set
- CONFIG_USB_OHCI_HCD=y
--# CONFIG_USB_OHCI_BIG_ENDIAN is not set
-+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
-+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
- CONFIG_USB_OHCI_LITTLE_ENDIAN=y
- # CONFIG_USB_SL811_HCD is not set
-
-@@ -671,6 +749,7 @@ CONFIG_USB_STORAGE_DEBUG=y
- # CONFIG_USB_ATI_REMOTE2 is not set
- # CONFIG_USB_KEYSPAN_REMOTE is not set
- # CONFIG_USB_APPLETOUCH is not set
-+# CONFIG_USB_GTCO is not set
-
- #
- # USB Imaging devices
-@@ -708,6 +787,7 @@ CONFIG_USB_MON=y
- # CONFIG_USB_RIO500 is not set
- # CONFIG_USB_LEGOTOWER is not set
- # CONFIG_USB_LCD is not set
-+# CONFIG_USB_BERRY_CHARGE is not set
- # CONFIG_USB_LED is not set
- # CONFIG_USB_CYPRESS_CY7C63 is not set
- # CONFIG_USB_CYTHERM is not set
-@@ -717,6 +797,7 @@ CONFIG_USB_MON=y
- # CONFIG_USB_APPLEDISPLAY is not set
- # CONFIG_USB_LD is not set
- # CONFIG_USB_TRANCEVIBRATOR is not set
-+# CONFIG_USB_IOWARRIOR is not set
- # CONFIG_USB_TEST is not set
-
- #
-@@ -889,6 +970,11 @@ CONFIG_NLS_ISO8859_1=y
- # CONFIG_NLS_UTF8 is not set
-
- #
-+# Distributed Lock Manager
-+#
-+# CONFIG_DLM is not set
-+
-+#
- # Profiling support
- #
- # CONFIG_PROFILING is not set
-@@ -900,28 +986,30 @@ CONFIG_NLS_ISO8859_1=y
- CONFIG_ENABLE_MUST_CHECK=y
- # CONFIG_MAGIC_SYSRQ is not set
- # CONFIG_UNUSED_SYMBOLS is not set
-+# CONFIG_DEBUG_FS is not set
-+# CONFIG_HEADERS_CHECK is not set
- CONFIG_DEBUG_KERNEL=y
-+# CONFIG_DEBUG_SHIRQ is not set
- CONFIG_LOG_BUF_SHIFT=14
- CONFIG_DETECT_SOFTLOCKUP=y
- # CONFIG_SCHEDSTATS is not set
-+# CONFIG_TIMER_STATS is not set
- # CONFIG_DEBUG_SLAB is not set
- # CONFIG_DEBUG_RT_MUTEXES is not set
- # CONFIG_RT_MUTEX_TESTER is not set
- # CONFIG_DEBUG_SPINLOCK is not set
- # CONFIG_DEBUG_MUTEXES is not set
--# CONFIG_DEBUG_RWSEMS is not set
- # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
- # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
- # CONFIG_DEBUG_KOBJECT is not set
- CONFIG_DEBUG_BUGVERBOSE=y
- # CONFIG_DEBUG_INFO is not set
--# CONFIG_DEBUG_FS is not set
- # CONFIG_DEBUG_VM is not set
- # CONFIG_DEBUG_LIST is not set
- CONFIG_FRAME_POINTER=y
- CONFIG_FORCED_INLINING=y
--# CONFIG_HEADERS_CHECK is not set
- # CONFIG_RCU_TORTURE_TEST is not set
-+# CONFIG_FAULT_INJECTION is not set
- CONFIG_DEBUG_USER=y
- # CONFIG_DEBUG_ERRORS is not set
- CONFIG_DEBUG_LL=y
-@@ -941,9 +1029,12 @@ CONFIG_DEBUG_LL=y
- #
- # Library routines
- #
-+CONFIG_BITREVERSE=y
- # CONFIG_CRC_CCITT is not set
- # CONFIG_CRC16 is not set
- CONFIG_CRC32=y
- # CONFIG_LIBCRC32C is not set
- CONFIG_ZLIB_INFLATE=y
- CONFIG_PLIST=y
-+CONFIG_HAS_IOMEM=y
-+CONFIG_HAS_IOPORT=y
-Index: linux-2.6.22.19/arch/arm/configs/at91sam9261ek_defconfig
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/configs/at91sam9261ek_defconfig
-+++ linux-2.6.22.19/arch/arm/configs/at91sam9261ek_defconfig
-@@ -1,18 +1,24 @@
- #
- # Automatically generated make config: don't edit
--# Linux kernel version: 2.6.19-rc6
--# Fri Nov 17 18:00:38 2006
-+# Linux kernel version: 2.6.21
-+# Mon May 7 11:42:30 2007
- #
- CONFIG_ARM=y
-+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-+CONFIG_GENERIC_GPIO=y
- # CONFIG_GENERIC_TIME is not set
- CONFIG_MMU=y
-+# CONFIG_NO_IOPORT is not set
- CONFIG_GENERIC_HARDIRQS=y
- CONFIG_TRACE_IRQFLAGS_SUPPORT=y
- CONFIG_HARDIRQS_SW_RESEND=y
- CONFIG_GENERIC_IRQ_PROBE=y
- CONFIG_RWSEM_GENERIC_SPINLOCK=y
-+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
- CONFIG_GENERIC_HWEIGHT=y
- CONFIG_GENERIC_CALIBRATE_DELAY=y
-+CONFIG_ZONE_DMA=y
- CONFIG_VECTORS_BASE=0xffff0000
- CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-@@ -31,13 +37,16 @@ CONFIG_LOCALVERSION=""
- # CONFIG_SWAP is not set
- CONFIG_SYSVIPC=y
- # CONFIG_IPC_NS is not set
-+CONFIG_SYSVIPC_SYSCTL=y
- # CONFIG_POSIX_MQUEUE is not set
- # CONFIG_BSD_PROCESS_ACCT is not set
- # CONFIG_TASKSTATS is not set
- # CONFIG_UTS_NS is not set
- # CONFIG_AUDIT is not set
- # CONFIG_IKCONFIG is not set
-+CONFIG_SYSFS_DEPRECATED=y
- # CONFIG_RELAY is not set
-+CONFIG_BLK_DEV_INITRD=y
- CONFIG_INITRAMFS_SOURCE=""
- CONFIG_CC_OPTIMIZE_FOR_SIZE=y
- CONFIG_SYSCTL=y
-@@ -76,7 +85,9 @@ CONFIG_KMOD=y
- # Block layer
- #
- CONFIG_BLOCK=y
-+# CONFIG_LBD is not set
- # CONFIG_BLK_DEV_IO_TRACE is not set
-+# CONFIG_LSF is not set
-
- #
- # IO Schedulers
-@@ -110,10 +121,12 @@ CONFIG_ARCH_AT91=y
- # CONFIG_ARCH_IMX is not set
- # CONFIG_ARCH_IOP32X is not set
- # CONFIG_ARCH_IOP33X is not set
-+# CONFIG_ARCH_IOP13XX is not set
- # CONFIG_ARCH_IXP4XX is not set
- # CONFIG_ARCH_IXP2000 is not set
- # CONFIG_ARCH_IXP23XX is not set
- # CONFIG_ARCH_L7200 is not set
-+# CONFIG_ARCH_NS9XXX is not set
- # CONFIG_ARCH_PNX4008 is not set
- # CONFIG_ARCH_PXA is not set
- # CONFIG_ARCH_RPC is not set
-@@ -129,6 +142,7 @@ CONFIG_ARCH_AT91=y
- # CONFIG_ARCH_AT91RM9200 is not set
- # CONFIG_ARCH_AT91SAM9260 is not set
- CONFIG_ARCH_AT91SAM9261=y
-+# CONFIG_ARCH_AT91SAM9263 is not set
-
- #
- # AT91SAM9261 Board Type
-@@ -138,12 +152,14 @@ CONFIG_MACH_AT91SAM9261EK=y
- #
- # AT91 Board Options
- #
-+# CONFIG_MTD_AT91_DATAFLASH_CARD is not set
- # CONFIG_MTD_NAND_AT91_BUSWIDTH_16 is not set
-
- #
- # AT91 Feature Selections
- #
- # CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set
-+# CONFIG_ATMEL_TCLIB is not set
-
- #
- # Processor Type
-@@ -166,6 +182,7 @@ CONFIG_CPU_CP15_MMU=y
- # CONFIG_CPU_DCACHE_DISABLE is not set
- # CONFIG_CPU_DCACHE_WRITETHROUGH is not set
- # CONFIG_CPU_CACHE_ROUND_ROBIN is not set
-+# CONFIG_OUTER_CACHE is not set
-
- #
- # Bus support
-@@ -193,6 +210,7 @@ CONFIG_FLAT_NODE_MEM_MAP=y
- # CONFIG_SPARSEMEM_STATIC is not set
- CONFIG_SPLIT_PTLOCK_CPUS=4096
- # CONFIG_RESOURCES_64BIT is not set
-+CONFIG_ZONE_DMA_FLAG=1
- # CONFIG_LEDS is not set
- CONFIG_ALIGNMENT_TRAP=y
-
-@@ -203,6 +221,7 @@ CONFIG_ZBOOT_ROM_TEXT=0x0
- CONFIG_ZBOOT_ROM_BSS=0x0
- CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw"
- # CONFIG_XIP_KERNEL is not set
-+# CONFIG_KEXEC is not set
-
- #
- # Floating point emulation
-@@ -228,7 +247,6 @@ CONFIG_BINFMT_ELF=y
- # Power management options
- #
- # CONFIG_PM is not set
--# CONFIG_APM is not set
-
- #
- # Networking
-@@ -245,6 +263,7 @@ CONFIG_UNIX=y
- CONFIG_XFRM=y
- # CONFIG_XFRM_USER is not set
- # CONFIG_XFRM_SUB_POLICY is not set
-+# CONFIG_XFRM_MIGRATE is not set
- # CONFIG_NET_KEY is not set
- CONFIG_INET=y
- # CONFIG_IP_MULTICAST is not set
-@@ -271,6 +290,7 @@ CONFIG_INET_TCP_DIAG=y
- # CONFIG_TCP_CONG_ADVANCED is not set
- CONFIG_TCP_CONG_CUBIC=y
- CONFIG_DEFAULT_TCP_CONG="cubic"
-+# CONFIG_TCP_MD5SIG is not set
- # CONFIG_IPV6 is not set
- # CONFIG_INET6_XFRM_TUNNEL is not set
- # CONFIG_INET6_TUNNEL is not set
-@@ -328,6 +348,7 @@ CONFIG_STANDALONE=y
- CONFIG_PREVENT_FIRMWARE_BUILD=y
- # CONFIG_FW_LOADER is not set
- # CONFIG_DEBUG_DRIVER is not set
-+# CONFIG_DEBUG_DEVRES is not set
- # CONFIG_SYS_HYPERVISOR is not set
-
- #
-@@ -350,6 +371,7 @@ CONFIG_MTD_CMDLINE_PARTS=y
- # User Modules And Translation Layers
- #
- # CONFIG_MTD_CHAR is not set
-+CONFIG_MTD_BLKDEVS=y
- CONFIG_MTD_BLOCK=y
- # CONFIG_FTL is not set
- # CONFIG_NFTL is not set
-@@ -386,6 +408,8 @@ CONFIG_MTD_CFI_I2=y
- #
- # Self-contained MTD device drivers
- #
-+# CONFIG_MTD_DATAFLASH is not set
-+# CONFIG_MTD_M25P80 is not set
- # CONFIG_MTD_SLRAM is not set
- # CONFIG_MTD_PHRAM is not set
- # CONFIG_MTD_MTDRAM is not set
-@@ -422,6 +446,7 @@ CONFIG_MTD_NAND_AT91=y
- #
- # Plug and Play support
- #
-+# CONFIG_PNPACPI is not set
-
- #
- # Block devices
-@@ -434,7 +459,6 @@ CONFIG_BLK_DEV_RAM=y
- CONFIG_BLK_DEV_RAM_COUNT=16
- CONFIG_BLK_DEV_RAM_SIZE=8192
- CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
--CONFIG_BLK_DEV_INITRD=y
- # CONFIG_CDROM_PKTCDVD is not set
- # CONFIG_ATA_OVER_ETH is not set
-
-@@ -443,6 +467,7 @@ CONFIG_BLK_DEV_INITRD=y
- #
- # CONFIG_RAID_ATTRS is not set
- CONFIG_SCSI=y
-+# CONFIG_SCSI_TGT is not set
- # CONFIG_SCSI_NETLINK is not set
- CONFIG_SCSI_PROC_FS=y
-
-@@ -462,6 +487,7 @@ CONFIG_BLK_DEV_SD=y
- CONFIG_SCSI_MULTI_LUN=y
- # CONFIG_SCSI_CONSTANTS is not set
- # CONFIG_SCSI_LOGGING is not set
-+# CONFIG_SCSI_SCAN_ASYNC is not set
-
- #
- # SCSI Transports
-@@ -479,6 +505,11 @@ CONFIG_SCSI_MULTI_LUN=y
- # CONFIG_SCSI_DEBUG is not set
-
- #
-+# Serial ATA (prod) and Parallel ATA (experimental) drivers
-+#
-+# CONFIG_ATA is not set
-+
-+#
- # Multi-device support (RAID and LVM)
- #
- # CONFIG_MD is not set
-@@ -575,7 +606,16 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
- # CONFIG_INPUT_KEYBOARD is not set
- # CONFIG_INPUT_MOUSE is not set
- # CONFIG_INPUT_JOYSTICK is not set
--# CONFIG_INPUT_TOUCHSCREEN is not set
-+CONFIG_INPUT_TOUCHSCREEN=y
-+CONFIG_TOUCHSCREEN_ADS7846=y
-+# CONFIG_TOUCHSCREEN_GUNZE is not set
-+# CONFIG_TOUCHSCREEN_ELO is not set
-+# CONFIG_TOUCHSCREEN_MTOUCH is not set
-+# CONFIG_TOUCHSCREEN_MK712 is not set
-+# CONFIG_TOUCHSCREEN_PENMOUNT is not set
-+# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
-+# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
-+# CONFIG_TOUCHSCREEN_UCB1400 is not set
- # CONFIG_INPUT_MISC is not set
-
- #
-@@ -634,10 +674,6 @@ CONFIG_HW_RANDOM=y
- # CONFIG_NVRAM is not set
- # CONFIG_DTLK is not set
- # CONFIG_R3964 is not set
--
--#
--# Ftape, the floppy tape device driver
--#
- # CONFIG_RAW_DRIVER is not set
-
- #
-@@ -662,6 +698,7 @@ CONFIG_I2C_CHARDEV=y
- # I2C Hardware Bus support
- #
- CONFIG_I2C_AT91=y
-+CONFIG_I2C_AT91_CLOCKRATE=100000
- # CONFIG_I2C_OCORES is not set
- # CONFIG_I2C_PARPORT_LIGHT is not set
- # CONFIG_I2C_STUB is not set
-@@ -686,8 +723,20 @@ CONFIG_I2C_AT91=y
- #
- # SPI support
- #
--# CONFIG_SPI is not set
--# CONFIG_SPI_MASTER is not set
-+CONFIG_SPI=y
-+# CONFIG_SPI_DEBUG is not set
-+CONFIG_SPI_MASTER=y
-+
-+#
-+# SPI Master Controller Drivers
-+#
-+CONFIG_SPI_ATMEL=y
-+# CONFIG_SPI_BITBANG is not set
-+
-+#
-+# SPI Protocol Masters
-+#
-+# CONFIG_SPI_AT25 is not set
-
- #
- # Dallas's 1-wire bus
-@@ -703,7 +752,11 @@ CONFIG_I2C_AT91=y
- #
- # Misc devices
- #
--# CONFIG_TIFM_CORE is not set
-+
-+#
-+# Multifunction device drivers
-+#
-+# CONFIG_MFD_SM501 is not set
-
- #
- # LED devices
-@@ -732,7 +785,7 @@ CONFIG_I2C_AT91=y
- #
- # Graphics support
- #
--# CONFIG_FIRMWARE_EDID is not set
-+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
- # CONFIG_FB is not set
-
- #
-@@ -740,7 +793,6 @@ CONFIG_I2C_AT91=y
- #
- # CONFIG_VGA_CONSOLE is not set
- CONFIG_DUMMY_CONSOLE=y
--# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
- #
- # Sound
-@@ -748,6 +800,12 @@ CONFIG_DUMMY_CONSOLE=y
- # CONFIG_SOUND is not set
-
- #
-+# HID Devices
-+#
-+CONFIG_HID=y
-+# CONFIG_HID_DEBUG is not set
-+
-+#
- # USB support
- #
- CONFIG_USB_ARCH_HAS_HCD=y
-@@ -760,7 +818,6 @@ CONFIG_USB=y
- # Miscellaneous USB options
- #
- CONFIG_USB_DEVICEFS=y
--# CONFIG_USB_BANDWIDTH is not set
- # CONFIG_USB_DYNAMIC_MINORS is not set
- # CONFIG_USB_OTG is not set
-
-@@ -769,7 +826,8 @@ CONFIG_USB_DEVICEFS=y
- #
- # CONFIG_USB_ISP116X_HCD is not set
- CONFIG_USB_OHCI_HCD=y
--# CONFIG_USB_OHCI_BIG_ENDIAN is not set
-+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
-+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
- CONFIG_USB_OHCI_LITTLE_ENDIAN=y
- # CONFIG_USB_SL811_HCD is not set
-
-@@ -821,6 +879,7 @@ CONFIG_USB_STORAGE_DEBUG=y
- # CONFIG_USB_ATI_REMOTE2 is not set
- # CONFIG_USB_KEYSPAN_REMOTE is not set
- # CONFIG_USB_APPLETOUCH is not set
-+# CONFIG_USB_GTCO is not set
-
- #
- # USB Imaging devices
-@@ -858,6 +917,7 @@ CONFIG_USB_MON=y
- # CONFIG_USB_RIO500 is not set
- # CONFIG_USB_LEGOTOWER is not set
- # CONFIG_USB_LCD is not set
-+# CONFIG_USB_BERRY_CHARGE is not set
- # CONFIG_USB_LED is not set
- # CONFIG_USB_CYPRESS_CY7C63 is not set
- # CONFIG_USB_CYTHERM is not set
-@@ -867,6 +927,7 @@ CONFIG_USB_MON=y
- # CONFIG_USB_APPLEDISPLAY is not set
- # CONFIG_USB_LD is not set
- # CONFIG_USB_TRANCEVIBRATOR is not set
-+# CONFIG_USB_IOWARRIOR is not set
- # CONFIG_USB_TEST is not set
-
- #
-@@ -903,7 +964,6 @@ CONFIG_MMC=y
- # CONFIG_MMC_DEBUG is not set
- CONFIG_MMC_BLOCK=y
- CONFIG_MMC_AT91=m
--# CONFIG_MMC_TIFM_SD is not set
-
- #
- # Real Time Clock
-@@ -973,7 +1033,6 @@ CONFIG_RAMFS=y
- # CONFIG_BEFS_FS is not set
- # CONFIG_BFS_FS is not set
- # CONFIG_EFS_FS is not set
--# CONFIG_JFFS_FS is not set
- # CONFIG_JFFS2_FS is not set
- CONFIG_CRAMFS=y
- # CONFIG_VXFS_FS is not set
-@@ -1045,6 +1104,11 @@ CONFIG_NLS_ISO8859_1=y
- # CONFIG_NLS_UTF8 is not set
-
- #
-+# Distributed Lock Manager
-+#
-+# CONFIG_DLM is not set
-+
-+#
- # Profiling support
- #
- # CONFIG_PROFILING is not set
-@@ -1056,28 +1120,30 @@ CONFIG_NLS_ISO8859_1=y
- CONFIG_ENABLE_MUST_CHECK=y
- # CONFIG_MAGIC_SYSRQ is not set
- # CONFIG_UNUSED_SYMBOLS is not set
-+# CONFIG_DEBUG_FS is not set
-+# CONFIG_HEADERS_CHECK is not set
- CONFIG_DEBUG_KERNEL=y
-+# CONFIG_DEBUG_SHIRQ is not set
- CONFIG_LOG_BUF_SHIFT=14
- CONFIG_DETECT_SOFTLOCKUP=y
- # CONFIG_SCHEDSTATS is not set
-+# CONFIG_TIMER_STATS is not set
- # CONFIG_DEBUG_SLAB is not set
- # CONFIG_DEBUG_RT_MUTEXES is not set
- # CONFIG_RT_MUTEX_TESTER is not set
- # CONFIG_DEBUG_SPINLOCK is not set
- # CONFIG_DEBUG_MUTEXES is not set
--# CONFIG_DEBUG_RWSEMS is not set
- # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
- # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
- # CONFIG_DEBUG_KOBJECT is not set
- CONFIG_DEBUG_BUGVERBOSE=y
- # CONFIG_DEBUG_INFO is not set
--# CONFIG_DEBUG_FS is not set
- # CONFIG_DEBUG_VM is not set
- # CONFIG_DEBUG_LIST is not set
- CONFIG_FRAME_POINTER=y
- CONFIG_FORCED_INLINING=y
--# CONFIG_HEADERS_CHECK is not set
- # CONFIG_RCU_TORTURE_TEST is not set
-+# CONFIG_FAULT_INJECTION is not set
- CONFIG_DEBUG_USER=y
- # CONFIG_DEBUG_ERRORS is not set
- CONFIG_DEBUG_LL=y
-@@ -1097,9 +1163,12 @@ CONFIG_DEBUG_LL=y
- #
- # Library routines
- #
-+CONFIG_BITREVERSE=y
- # CONFIG_CRC_CCITT is not set
- # CONFIG_CRC16 is not set
- CONFIG_CRC32=y
- # CONFIG_LIBCRC32C is not set
- CONFIG_ZLIB_INFLATE=y
- CONFIG_PLIST=y
-+CONFIG_HAS_IOMEM=y
-+CONFIG_HAS_IOPORT=y
-Index: linux-2.6.22.19/arch/arm/configs/at91sam9263ek_defconfig
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/configs/at91sam9263ek_defconfig
-+++ linux-2.6.22.19/arch/arm/configs/at91sam9263ek_defconfig
-@@ -1,11 +1,14 @@
- #
- # Automatically generated make config: don't edit
--# Linux kernel version: 2.6.20-rc1
--# Mon Jan 8 16:06:54 2007
-+# Linux kernel version: 2.6.21
-+# Mon May 7 11:42:49 2007
- #
- CONFIG_ARM=y
-+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-+CONFIG_GENERIC_GPIO=y
- # CONFIG_GENERIC_TIME is not set
- CONFIG_MMU=y
-+# CONFIG_NO_IOPORT is not set
- CONFIG_GENERIC_HARDIRQS=y
- CONFIG_TRACE_IRQFLAGS_SUPPORT=y
- CONFIG_HARDIRQS_SW_RESEND=y
-@@ -15,6 +18,7 @@ CONFIG_RWSEM_GENERIC_SPINLOCK=y
- # CONFIG_ARCH_HAS_ILOG2_U64 is not set
- CONFIG_GENERIC_HWEIGHT=y
- CONFIG_GENERIC_CALIBRATE_DELAY=y
-+CONFIG_ZONE_DMA=y
- CONFIG_VECTORS_BASE=0xffff0000
- CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-@@ -33,6 +37,7 @@ CONFIG_LOCALVERSION=""
- # CONFIG_SWAP is not set
- CONFIG_SYSVIPC=y
- # CONFIG_IPC_NS is not set
-+CONFIG_SYSVIPC_SYSCTL=y
- # CONFIG_POSIX_MQUEUE is not set
- # CONFIG_BSD_PROCESS_ACCT is not set
- # CONFIG_TASKSTATS is not set
-@@ -41,6 +46,7 @@ CONFIG_SYSVIPC=y
- # CONFIG_IKCONFIG is not set
- CONFIG_SYSFS_DEPRECATED=y
- # CONFIG_RELAY is not set
-+CONFIG_BLK_DEV_INITRD=y
- CONFIG_INITRAMFS_SOURCE=""
- CONFIG_CC_OPTIMIZE_FOR_SIZE=y
- CONFIG_SYSCTL=y
-@@ -120,6 +126,7 @@ CONFIG_ARCH_AT91=y
- # CONFIG_ARCH_IXP2000 is not set
- # CONFIG_ARCH_IXP23XX is not set
- # CONFIG_ARCH_L7200 is not set
-+# CONFIG_ARCH_NS9XXX is not set
- # CONFIG_ARCH_PNX4008 is not set
- # CONFIG_ARCH_PXA is not set
- # CONFIG_ARCH_RPC is not set
-@@ -152,6 +159,7 @@ CONFIG_MTD_AT91_DATAFLASH_CARD=y
- # AT91 Feature Selections
- #
- # CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set
-+# CONFIG_ATMEL_TCLIB is not set
-
- #
- # Processor Type
-@@ -174,6 +182,7 @@ CONFIG_CPU_CP15_MMU=y
- # CONFIG_CPU_DCACHE_DISABLE is not set
- # CONFIG_CPU_DCACHE_WRITETHROUGH is not set
- # CONFIG_CPU_CACHE_ROUND_ROBIN is not set
-+# CONFIG_OUTER_CACHE is not set
-
- #
- # Bus support
-@@ -201,6 +210,7 @@ CONFIG_FLAT_NODE_MEM_MAP=y
- # CONFIG_SPARSEMEM_STATIC is not set
- CONFIG_SPLIT_PTLOCK_CPUS=4096
- # CONFIG_RESOURCES_64BIT is not set
-+CONFIG_ZONE_DMA_FLAG=1
- # CONFIG_LEDS is not set
- CONFIG_ALIGNMENT_TRAP=y
-
-@@ -211,6 +221,7 @@ CONFIG_ZBOOT_ROM_TEXT=0x0
- CONFIG_ZBOOT_ROM_BSS=0x0
- CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw"
- # CONFIG_XIP_KERNEL is not set
-+# CONFIG_KEXEC is not set
-
- #
- # Floating point emulation
-@@ -236,7 +247,6 @@ CONFIG_BINFMT_ELF=y
- # Power management options
- #
- # CONFIG_PM is not set
--# CONFIG_APM is not set
-
- #
- # Networking
-@@ -333,6 +343,7 @@ CONFIG_STANDALONE=y
- CONFIG_PREVENT_FIRMWARE_BUILD=y
- # CONFIG_FW_LOADER is not set
- # CONFIG_DEBUG_DRIVER is not set
-+# CONFIG_DEBUG_DEVRES is not set
- # CONFIG_SYS_HYPERVISOR is not set
-
- #
-@@ -430,6 +441,7 @@ CONFIG_MTD_NAND_AT91=y
- #
- # Plug and Play support
- #
-+# CONFIG_PNPACPI is not set
-
- #
- # Block devices
-@@ -443,7 +455,6 @@ CONFIG_BLK_DEV_RAM=y
- CONFIG_BLK_DEV_RAM_COUNT=16
- CONFIG_BLK_DEV_RAM_SIZE=8192
- CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
--CONFIG_BLK_DEV_INITRD=y
- # CONFIG_CDROM_PKTCDVD is not set
- # CONFIG_ATA_OVER_ETH is not set
-
-@@ -531,6 +542,7 @@ CONFIG_NETDEVICES=y
- #
- CONFIG_NET_ETHERNET=y
- CONFIG_MII=y
-+CONFIG_MACB=y
- # CONFIG_SMC91X is not set
- # CONFIG_DM9000 is not set
-
-@@ -685,6 +697,7 @@ CONFIG_I2C_CHARDEV=y
- # I2C Hardware Bus support
- #
- CONFIG_I2C_AT91=y
-+CONFIG_I2C_AT91_CLOCKRATE=100000
- # CONFIG_I2C_OCORES is not set
- # CONFIG_I2C_PARPORT_LIGHT is not set
- # CONFIG_I2C_STUB is not set
-@@ -722,6 +735,7 @@ CONFIG_SPI_ATMEL=y
- #
- # SPI Protocol Masters
- #
-+# CONFIG_SPI_AT25 is not set
-
- #
- # Dallas's 1-wire bus
-@@ -737,7 +751,11 @@ CONFIG_SPI_ATMEL=y
- #
- # Misc devices
- #
--# CONFIG_TIFM_CORE is not set
-+
-+#
-+# Multifunction device drivers
-+#
-+# CONFIG_MFD_SM501 is not set
-
- #
- # LED devices
-@@ -766,15 +784,23 @@ CONFIG_SPI_ATMEL=y
- #
- # Graphics support
- #
--# CONFIG_FIRMWARE_EDID is not set
-+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
- CONFIG_FB=y
-+# CONFIG_FIRMWARE_EDID is not set
-+# CONFIG_FB_DDC is not set
- # CONFIG_FB_CFB_FILLRECT is not set
- # CONFIG_FB_CFB_COPYAREA is not set
- # CONFIG_FB_CFB_IMAGEBLIT is not set
-+# CONFIG_FB_SVGALIB is not set
- # CONFIG_FB_MACMODES is not set
- # CONFIG_FB_BACKLIGHT is not set
- # CONFIG_FB_MODE_HELPERS is not set
- # CONFIG_FB_TILEBLITTING is not set
-+
-+#
-+# Frame buffer hardware drivers
-+#
-+# CONFIG_FB_S1D15605 is not set
- # CONFIG_FB_S1D13XXX is not set
- # CONFIG_FB_VIRTUAL is not set
-
-@@ -789,7 +815,6 @@ CONFIG_DUMMY_CONSOLE=y
- # Logo configuration
- #
- # CONFIG_LOGO is not set
--# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
- #
- # Sound
-@@ -800,6 +825,7 @@ CONFIG_DUMMY_CONSOLE=y
- # HID Devices
- #
- CONFIG_HID=y
-+# CONFIG_HID_DEBUG is not set
-
- #
- # USB support
-@@ -814,9 +840,7 @@ CONFIG_USB=y
- # Miscellaneous USB options
- #
- CONFIG_USB_DEVICEFS=y
--# CONFIG_USB_BANDWIDTH is not set
- # CONFIG_USB_DYNAMIC_MINORS is not set
--# CONFIG_USB_MULTITHREAD_PROBE is not set
- # CONFIG_USB_OTG is not set
-
- #
-@@ -824,7 +848,8 @@ CONFIG_USB_DEVICEFS=y
- #
- # CONFIG_USB_ISP116X_HCD is not set
- CONFIG_USB_OHCI_HCD=y
--# CONFIG_USB_OHCI_BIG_ENDIAN is not set
-+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
-+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
- CONFIG_USB_OHCI_LITTLE_ENDIAN=y
- # CONFIG_USB_SL811_HCD is not set
-
-@@ -877,6 +902,7 @@ CONFIG_USB_STORAGE=y
- # CONFIG_USB_ATI_REMOTE2 is not set
- # CONFIG_USB_KEYSPAN_REMOTE is not set
- # CONFIG_USB_APPLETOUCH is not set
-+# CONFIG_USB_GTCO is not set
-
- #
- # USB Imaging devices
-@@ -914,6 +940,7 @@ CONFIG_USB_MON=y
- # CONFIG_USB_RIO500 is not set
- # CONFIG_USB_LEGOTOWER is not set
- # CONFIG_USB_LCD is not set
-+# CONFIG_USB_BERRY_CHARGE is not set
- # CONFIG_USB_LED is not set
- # CONFIG_USB_CYPRESS_CY7C63 is not set
- # CONFIG_USB_CYTHERM is not set
-@@ -923,6 +950,7 @@ CONFIG_USB_MON=y
- # CONFIG_USB_APPLEDISPLAY is not set
- # CONFIG_USB_LD is not set
- # CONFIG_USB_TRANCEVIBRATOR is not set
-+# CONFIG_USB_IOWARRIOR is not set
- # CONFIG_USB_TEST is not set
-
- #
-@@ -959,7 +987,6 @@ CONFIG_MMC=y
- # CONFIG_MMC_DEBUG is not set
- CONFIG_MMC_BLOCK=y
- CONFIG_MMC_AT91=m
--# CONFIG_MMC_TIFM_SD is not set
-
- #
- # Real Time Clock
-@@ -1136,15 +1163,16 @@ CONFIG_ENABLE_MUST_CHECK=y
- # CONFIG_DEBUG_FS is not set
- # CONFIG_HEADERS_CHECK is not set
- CONFIG_DEBUG_KERNEL=y
-+# CONFIG_DEBUG_SHIRQ is not set
- CONFIG_LOG_BUF_SHIFT=14
- CONFIG_DETECT_SOFTLOCKUP=y
- # CONFIG_SCHEDSTATS is not set
-+# CONFIG_TIMER_STATS is not set
- # CONFIG_DEBUG_SLAB is not set
- # CONFIG_DEBUG_RT_MUTEXES is not set
- # CONFIG_RT_MUTEX_TESTER is not set
- # CONFIG_DEBUG_SPINLOCK is not set
- # CONFIG_DEBUG_MUTEXES is not set
--# CONFIG_DEBUG_RWSEMS is not set
- # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
- # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
- # CONFIG_DEBUG_KOBJECT is not set
-@@ -1155,6 +1183,7 @@ CONFIG_DEBUG_BUGVERBOSE=y
- CONFIG_FRAME_POINTER=y
- CONFIG_FORCED_INLINING=y
- # CONFIG_RCU_TORTURE_TEST is not set
-+# CONFIG_FAULT_INJECTION is not set
- CONFIG_DEBUG_USER=y
- # CONFIG_DEBUG_ERRORS is not set
- CONFIG_DEBUG_LL=y
-@@ -1180,5 +1209,7 @@ CONFIG_BITREVERSE=y
- CONFIG_CRC32=y
- # CONFIG_LIBCRC32C is not set
- CONFIG_ZLIB_INFLATE=y
-+CONFIG_ZLIB_DEFLATE=y
- CONFIG_PLIST=y
--CONFIG_IOMAP_COPY=y
-+CONFIG_HAS_IOMEM=y
-+CONFIG_HAS_IOPORT=y
-Index: linux-2.6.22.19/arch/arm/configs/cam60_defconfig
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/arch/arm/configs/cam60_defconfig
-@@ -0,0 +1,954 @@
-+#
-+# Automatically generated make config: don't edit
-+# Linux kernel version: 2.6.20
-+# Tue May 1 21:06:33 2007
-+#
-+CONFIG_ARM=y
-+# CONFIG_GENERIC_TIME is not set
-+CONFIG_MMU=y
-+CONFIG_GENERIC_HARDIRQS=y
-+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-+CONFIG_HARDIRQS_SW_RESEND=y
-+CONFIG_GENERIC_IRQ_PROBE=y
-+CONFIG_RWSEM_GENERIC_SPINLOCK=y
-+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-+CONFIG_GENERIC_HWEIGHT=y
-+CONFIG_GENERIC_CALIBRATE_DELAY=y
-+CONFIG_VECTORS_BASE=0xffff0000
-+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-+
-+#
-+# Code maturity level options
-+#
-+CONFIG_EXPERIMENTAL=y
-+CONFIG_BROKEN_ON_SMP=y
-+CONFIG_INIT_ENV_ARG_LIMIT=32
-+
-+#
-+# General setup
-+#
-+CONFIG_LOCALVERSION=""
-+# CONFIG_LOCALVERSION_AUTO is not set
-+# CONFIG_SWAP is not set
-+CONFIG_SYSVIPC=y
-+# CONFIG_IPC_NS is not set
-+# CONFIG_POSIX_MQUEUE is not set
-+# CONFIG_BSD_PROCESS_ACCT is not set
-+# CONFIG_TASKSTATS is not set
-+# CONFIG_UTS_NS is not set
-+# CONFIG_AUDIT is not set
-+CONFIG_IKCONFIG=y
-+CONFIG_IKCONFIG_PROC=y
-+CONFIG_SYSFS_DEPRECATED=y
-+# CONFIG_RELAY is not set
-+CONFIG_INITRAMFS_SOURCE=""
-+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-+CONFIG_SYSCTL=y
-+# CONFIG_EMBEDDED is not set
-+CONFIG_UID16=y
-+CONFIG_SYSCTL_SYSCALL=y
-+CONFIG_KALLSYMS=y
-+# CONFIG_KALLSYMS_ALL is not set
-+# CONFIG_KALLSYMS_EXTRA_PASS is not set
-+CONFIG_HOTPLUG=y
-+CONFIG_PRINTK=y
-+CONFIG_BUG=y
-+CONFIG_ELF_CORE=y
-+CONFIG_BASE_FULL=y
-+CONFIG_FUTEX=y
-+CONFIG_EPOLL=y
-+CONFIG_SHMEM=y
-+CONFIG_SLAB=y
-+CONFIG_VM_EVENT_COUNTERS=y
-+CONFIG_RT_MUTEXES=y
-+# CONFIG_TINY_SHMEM is not set
-+CONFIG_BASE_SMALL=0
-+# CONFIG_SLOB is not set
-+
-+#
-+# Loadable module support
-+#
-+CONFIG_MODULES=y
-+CONFIG_MODULE_UNLOAD=y
-+CONFIG_MODULE_FORCE_UNLOAD=y
-+# CONFIG_MODVERSIONS is not set
-+# CONFIG_MODULE_SRCVERSION_ALL is not set
-+# CONFIG_KMOD is not set
-+
-+#
-+# Block layer
-+#
-+CONFIG_BLOCK=y
-+# CONFIG_LBD is not set
-+# CONFIG_BLK_DEV_IO_TRACE is not set
-+# CONFIG_LSF is not set
-+
-+#
-+# IO Schedulers
-+#
-+CONFIG_IOSCHED_NOOP=y
-+CONFIG_IOSCHED_AS=y
-+# CONFIG_IOSCHED_DEADLINE is not set
-+# CONFIG_IOSCHED_CFQ is not set
-+CONFIG_DEFAULT_AS=y
-+# CONFIG_DEFAULT_DEADLINE is not set
-+# CONFIG_DEFAULT_CFQ is not set
-+# CONFIG_DEFAULT_NOOP is not set
-+CONFIG_DEFAULT_IOSCHED="anticipatory"
-+
-+#
-+# System Type
-+#
-+# CONFIG_ARCH_AAEC2000 is not set
-+# CONFIG_ARCH_INTEGRATOR is not set
-+# CONFIG_ARCH_REALVIEW is not set
-+# CONFIG_ARCH_VERSATILE is not set
-+CONFIG_ARCH_AT91=y
-+# CONFIG_ARCH_CLPS7500 is not set
-+# CONFIG_ARCH_CLPS711X is not set
-+# CONFIG_ARCH_CO285 is not set
-+# CONFIG_ARCH_EBSA110 is not set
-+# CONFIG_ARCH_EP93XX is not set
-+# CONFIG_ARCH_FOOTBRIDGE is not set
-+# CONFIG_ARCH_NETX is not set
-+# CONFIG_ARCH_H720X is not set
-+# CONFIG_ARCH_IMX is not set
-+# CONFIG_ARCH_IOP32X is not set
-+# CONFIG_ARCH_IOP33X is not set
-+# CONFIG_ARCH_IOP13XX is not set
-+# CONFIG_ARCH_IXP4XX is not set
-+# CONFIG_ARCH_IXP2000 is not set
-+# CONFIG_ARCH_IXP23XX is not set
-+# CONFIG_ARCH_L7200 is not set
-+# CONFIG_ARCH_PNX4008 is not set
-+# CONFIG_ARCH_PXA is not set
-+# CONFIG_ARCH_RPC is not set
-+# CONFIG_ARCH_SA1100 is not set
-+# CONFIG_ARCH_S3C2410 is not set
-+# CONFIG_ARCH_SHARK is not set
-+# CONFIG_ARCH_LH7A40X is not set
-+# CONFIG_ARCH_OMAP is not set
-+
-+#
-+# Atmel AT91 System-on-Chip
-+#
-+# CONFIG_ARCH_AT91RM9200 is not set
-+CONFIG_ARCH_AT91SAM9260=y
-+# CONFIG_ARCH_AT91SAM9261 is not set
-+# CONFIG_ARCH_AT91SAM9263 is not set
-+
-+#
-+# AT91SAM9260 Board Type
-+#
-+# CONFIG_MACH_AT91SAM9260EK is not set
-+CONFIG_MACH_CAM60=y
-+
-+#
-+# AT91 Board Options
-+#
-+
-+#
-+# AT91 Feature Selections
-+#
-+# CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set
-+
-+#
-+# Processor Type
-+#
-+CONFIG_CPU_32=y
-+CONFIG_CPU_ARM926T=y
-+CONFIG_CPU_32v5=y
-+CONFIG_CPU_ABRT_EV5TJ=y
-+CONFIG_CPU_CACHE_VIVT=y
-+CONFIG_CPU_COPY_V4WB=y
-+CONFIG_CPU_TLB_V4WBI=y
-+CONFIG_CPU_CP15=y
-+CONFIG_CPU_CP15_MMU=y
-+
-+#
-+# Processor Features
-+#
-+# CONFIG_ARM_THUMB is not set
-+# CONFIG_CPU_ICACHE_DISABLE is not set
-+# CONFIG_CPU_DCACHE_DISABLE is not set
-+# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
-+# CONFIG_CPU_CACHE_ROUND_ROBIN is not set
-+
-+#
-+# Bus support
-+#
-+
-+#
-+# PCCARD (PCMCIA/CardBus) support
-+#
-+# CONFIG_PCCARD is not set
-+
-+#
-+# Kernel Features
-+#
-+# CONFIG_PREEMPT is not set
-+# CONFIG_NO_IDLE_HZ is not set
-+CONFIG_HZ=100
-+# CONFIG_AEABI is not set
-+# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
-+CONFIG_SELECT_MEMORY_MODEL=y
-+CONFIG_FLATMEM_MANUAL=y
-+# CONFIG_DISCONTIGMEM_MANUAL is not set
-+# CONFIG_SPARSEMEM_MANUAL is not set
-+CONFIG_FLATMEM=y
-+CONFIG_FLAT_NODE_MEM_MAP=y
-+# CONFIG_SPARSEMEM_STATIC is not set
-+CONFIG_SPLIT_PTLOCK_CPUS=4096
-+# CONFIG_RESOURCES_64BIT is not set
-+# CONFIG_LEDS is not set
-+CONFIG_ALIGNMENT_TRAP=y
-+
-+#
-+# Boot options
-+#
-+CONFIG_ZBOOT_ROM_TEXT=0x22000000
-+CONFIG_ZBOOT_ROM_BSS=0x20004000
-+# CONFIG_ZBOOT_ROM is not set
-+CONFIG_CMDLINE="console=ttyS0,115200 noinitrd root=/dev/mtdblock3 rootfstype=jffs2 mem=64M"
-+# CONFIG_XIP_KERNEL is not set
-+
-+#
-+# Floating point emulation
-+#
-+
-+#
-+# At least one emulation must be selected
-+#
-+CONFIG_FPE_NWFPE=y
-+# CONFIG_FPE_NWFPE_XP is not set
-+# CONFIG_FPE_FASTFPE is not set
-+# CONFIG_VFP is not set
-+
-+#
-+# Userspace binary formats
-+#
-+CONFIG_BINFMT_ELF=y
-+# CONFIG_BINFMT_AOUT is not set
-+# CONFIG_BINFMT_MISC is not set
-+# CONFIG_ARTHUR is not set
-+
-+#
-+# Power management options
-+#
-+# CONFIG_PM is not set
-+# CONFIG_APM is not set
-+
-+#
-+# Networking
-+#
-+CONFIG_NET=y
-+
-+#
-+# Networking options
-+#
-+# CONFIG_NETDEBUG is not set
-+CONFIG_PACKET=y
-+# CONFIG_PACKET_MMAP is not set
-+CONFIG_UNIX=y
-+CONFIG_XFRM=y
-+# CONFIG_XFRM_USER is not set
-+# CONFIG_XFRM_SUB_POLICY is not set
-+# CONFIG_NET_KEY is not set
-+CONFIG_INET=y
-+# CONFIG_IP_MULTICAST is not set
-+# CONFIG_IP_ADVANCED_ROUTER is not set
-+CONFIG_IP_FIB_HASH=y
-+CONFIG_IP_PNP=y
-+# CONFIG_IP_PNP_DHCP is not set
-+CONFIG_IP_PNP_BOOTP=y
-+# CONFIG_IP_PNP_RARP is not set
-+# CONFIG_NET_IPIP is not set
-+# CONFIG_NET_IPGRE is not set
-+# CONFIG_ARPD is not set
-+# CONFIG_SYN_COOKIES is not set
-+# CONFIG_INET_AH is not set
-+# CONFIG_INET_ESP is not set
-+# CONFIG_INET_IPCOMP is not set
-+# CONFIG_INET_XFRM_TUNNEL is not set
-+# CONFIG_INET_TUNNEL is not set
-+CONFIG_INET_XFRM_MODE_TRANSPORT=y
-+CONFIG_INET_XFRM_MODE_TUNNEL=y
-+CONFIG_INET_XFRM_MODE_BEET=y
-+CONFIG_INET_DIAG=y
-+CONFIG_INET_TCP_DIAG=y
-+# CONFIG_TCP_CONG_ADVANCED is not set
-+CONFIG_TCP_CONG_CUBIC=y
-+CONFIG_DEFAULT_TCP_CONG="cubic"
-+# CONFIG_TCP_MD5SIG is not set
-+# CONFIG_IPV6 is not set
-+# CONFIG_INET6_XFRM_TUNNEL is not set
-+# CONFIG_INET6_TUNNEL is not set
-+# CONFIG_NETWORK_SECMARK is not set
-+# CONFIG_NETFILTER is not set
-+
-+#
-+# DCCP Configuration (EXPERIMENTAL)
-+#
-+# CONFIG_IP_DCCP is not set
-+
-+#
-+# SCTP Configuration (EXPERIMENTAL)
-+#
-+# CONFIG_IP_SCTP is not set
-+
-+#
-+# TIPC Configuration (EXPERIMENTAL)
-+#
-+# CONFIG_TIPC is not set
-+# CONFIG_ATM is not set
-+# CONFIG_BRIDGE is not set
-+# CONFIG_VLAN_8021Q is not set
-+# CONFIG_DECNET is not set
-+# CONFIG_LLC2 is not set
-+# CONFIG_IPX is not set
-+# CONFIG_ATALK is not set
-+# CONFIG_X25 is not set
-+# CONFIG_LAPB is not set
-+# CONFIG_ECONET is not set
-+# CONFIG_WAN_ROUTER is not set
-+
-+#
-+# QoS and/or fair queueing
-+#
-+# CONFIG_NET_SCHED is not set
-+
-+#
-+# Network testing
-+#
-+# CONFIG_NET_PKTGEN is not set
-+# CONFIG_HAMRADIO is not set
-+# CONFIG_IRDA is not set
-+# CONFIG_BT is not set
-+# CONFIG_IEEE80211 is not set
-+
-+#
-+# Device Drivers
-+#
-+
-+#
-+# Generic Driver Options
-+#
-+CONFIG_STANDALONE=y
-+CONFIG_PREVENT_FIRMWARE_BUILD=y
-+# CONFIG_FW_LOADER is not set
-+# CONFIG_DEBUG_DRIVER is not set
-+# CONFIG_SYS_HYPERVISOR is not set
-+
-+#
-+# Connector - unified userspace <-> kernelspace linker
-+#
-+# CONFIG_CONNECTOR is not set
-+
-+#
-+# Memory Technology Devices (MTD)
-+#
-+CONFIG_MTD=y
-+# CONFIG_MTD_DEBUG is not set
-+CONFIG_MTD_CONCAT=y
-+CONFIG_MTD_PARTITIONS=y
-+# CONFIG_MTD_REDBOOT_PARTS is not set
-+CONFIG_MTD_CMDLINE_PARTS=y
-+# CONFIG_MTD_AFS_PARTS is not set
-+
-+#
-+# User Modules And Translation Layers
-+#
-+CONFIG_MTD_CHAR=y
-+CONFIG_MTD_BLKDEVS=y
-+CONFIG_MTD_BLOCK=y
-+# CONFIG_FTL is not set
-+# CONFIG_NFTL is not set
-+# CONFIG_INFTL is not set
-+# CONFIG_RFD_FTL is not set
-+# CONFIG_SSFDC is not set
-+
-+#
-+# RAM/ROM/Flash chip drivers
-+#
-+CONFIG_MTD_CFI=y
-+# CONFIG_MTD_JEDECPROBE is not set
-+CONFIG_MTD_GEN_PROBE=y
-+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
-+CONFIG_MTD_MAP_BANK_WIDTH_1=y
-+CONFIG_MTD_MAP_BANK_WIDTH_2=y
-+CONFIG_MTD_MAP_BANK_WIDTH_4=y
-+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
-+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
-+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
-+CONFIG_MTD_CFI_I1=y
-+CONFIG_MTD_CFI_I2=y
-+# CONFIG_MTD_CFI_I4 is not set
-+# CONFIG_MTD_CFI_I8 is not set
-+# CONFIG_MTD_CFI_INTELEXT is not set
-+# CONFIG_MTD_CFI_AMDSTD is not set
-+# CONFIG_MTD_CFI_STAA is not set
-+# CONFIG_MTD_RAM is not set
-+# CONFIG_MTD_ROM is not set
-+# CONFIG_MTD_ABSENT is not set
-+# CONFIG_MTD_OBSOLETE_CHIPS is not set
-+
-+#
-+# Mapping drivers for chip access
-+#
-+CONFIG_MTD_COMPLEX_MAPPINGS=y
-+# CONFIG_MTD_PHYSMAP is not set
-+# CONFIG_MTD_ARM_INTEGRATOR is not set
-+# CONFIG_MTD_PLATRAM is not set
-+
-+#
-+# Self-contained MTD device drivers
-+#
-+CONFIG_MTD_DATAFLASH=y
-+# CONFIG_MTD_M25P80 is not set
-+# CONFIG_MTD_SLRAM is not set
-+# CONFIG_MTD_PHRAM is not set
-+# CONFIG_MTD_MTDRAM is not set
-+# CONFIG_MTD_BLOCK2MTD is not set
-+
-+#
-+# Disk-On-Chip Device Drivers
-+#
-+# CONFIG_MTD_DOC2000 is not set
-+# CONFIG_MTD_DOC2001 is not set
-+# CONFIG_MTD_DOC2001PLUS is not set
-+
-+#
-+# NAND Flash Device Drivers
-+#
-+# CONFIG_MTD_NAND is not set
-+
-+#
-+# OneNAND Flash Device Drivers
-+#
-+# CONFIG_MTD_ONENAND is not set
-+
-+#
-+# Parallel port support
-+#
-+# CONFIG_PARPORT is not set
-+
-+#
-+# Plug and Play support
-+#
-+
-+#
-+# Block devices
-+#
-+# CONFIG_BLK_DEV_COW_COMMON is not set
-+# CONFIG_BLK_DEV_LOOP is not set
-+# CONFIG_BLK_DEV_NBD is not set
-+CONFIG_BLK_DEV_RAM=y
-+CONFIG_BLK_DEV_RAM_COUNT=16
-+CONFIG_BLK_DEV_RAM_SIZE=8192
-+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
-+CONFIG_BLK_DEV_INITRD=y
-+# CONFIG_CDROM_PKTCDVD is not set
-+# CONFIG_ATA_OVER_ETH is not set
-+
-+#
-+# SCSI device support
-+#
-+# CONFIG_RAID_ATTRS is not set
-+# CONFIG_SCSI is not set
-+# CONFIG_SCSI_NETLINK is not set
-+
-+#
-+# Serial ATA (prod) and Parallel ATA (experimental) drivers
-+#
-+# CONFIG_ATA is not set
-+
-+#
-+# Multi-device support (RAID and LVM)
-+#
-+# CONFIG_MD is not set
-+
-+#
-+# Fusion MPT device support
-+#
-+# CONFIG_FUSION is not set
-+
-+#
-+# IEEE 1394 (FireWire) support
-+#
-+
-+#
-+# I2O device support
-+#
-+
-+#
-+# Network device support
-+#
-+CONFIG_NETDEVICES=y
-+# CONFIG_DUMMY is not set
-+# CONFIG_BONDING is not set
-+# CONFIG_EQUALIZER is not set
-+# CONFIG_TUN is not set
-+
-+#
-+# PHY device support
-+#
-+# CONFIG_PHYLIB is not set
-+
-+#
-+# Ethernet (10 or 100Mbit)
-+#
-+CONFIG_NET_ETHERNET=y
-+CONFIG_MII=y
-+CONFIG_MACB=y
-+# CONFIG_SMC91X is not set
-+# CONFIG_DM9000 is not set
-+
-+#
-+# Ethernet (1000 Mbit)
-+#
-+
-+#
-+# Ethernet (10000 Mbit)
-+#
-+
-+#
-+# Token Ring devices
-+#
-+
-+#
-+# Wireless LAN (non-hamradio)
-+#
-+# CONFIG_NET_RADIO is not set
-+
-+#
-+# Wan interfaces
-+#
-+# CONFIG_WAN is not set
-+# CONFIG_PPP is not set
-+# CONFIG_SLIP is not set
-+# CONFIG_SHAPER is not set
-+# CONFIG_NETCONSOLE is not set
-+# CONFIG_NETPOLL is not set
-+# CONFIG_NET_POLL_CONTROLLER is not set
-+
-+#
-+# ISDN subsystem
-+#
-+# CONFIG_ISDN is not set
-+
-+#
-+# Input device support
-+#
-+CONFIG_INPUT=y
-+# CONFIG_INPUT_FF_MEMLESS is not set
-+
-+#
-+# Userland interfaces
-+#
-+CONFIG_INPUT_MOUSEDEV=y
-+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
-+# CONFIG_INPUT_JOYDEV is not set
-+# CONFIG_INPUT_TSDEV is not set
-+# CONFIG_INPUT_EVDEV is not set
-+# CONFIG_INPUT_EVBUG is not set
-+
-+#
-+# Input Device Drivers
-+#
-+# CONFIG_INPUT_KEYBOARD is not set
-+# CONFIG_INPUT_MOUSE is not set
-+# CONFIG_INPUT_JOYSTICK is not set
-+# CONFIG_INPUT_TOUCHSCREEN is not set
-+# CONFIG_INPUT_MISC is not set
-+
-+#
-+# Hardware I/O ports
-+#
-+# CONFIG_SERIO is not set
-+# CONFIG_GAMEPORT is not set
-+
-+#
-+# Character devices
-+#
-+CONFIG_VT=y
-+CONFIG_VT_CONSOLE=y
-+CONFIG_HW_CONSOLE=y
-+# CONFIG_VT_HW_CONSOLE_BINDING is not set
-+# CONFIG_SERIAL_NONSTANDARD is not set
-+
-+#
-+# Serial drivers
-+#
-+# CONFIG_SERIAL_8250 is not set
-+
-+#
-+# Non-8250 serial port support
-+#
-+CONFIG_SERIAL_ATMEL=y
-+CONFIG_SERIAL_ATMEL_CONSOLE=y
-+# CONFIG_SERIAL_ATMEL_TTYAT is not set
-+CONFIG_SERIAL_CORE=y
-+CONFIG_SERIAL_CORE_CONSOLE=y
-+CONFIG_UNIX98_PTYS=y
-+CONFIG_LEGACY_PTYS=y
-+CONFIG_LEGACY_PTY_COUNT=256
-+
-+#
-+# IPMI
-+#
-+# CONFIG_IPMI_HANDLER is not set
-+
-+#
-+# Watchdog Cards
-+#
-+# CONFIG_WATCHDOG is not set
-+# CONFIG_HW_RANDOM is not set
-+# CONFIG_NVRAM is not set
-+# CONFIG_DTLK is not set
-+# CONFIG_R3964 is not set
-+# CONFIG_RAW_DRIVER is not set
-+
-+#
-+# TPM devices
-+#
-+# CONFIG_TCG_TPM is not set
-+
-+#
-+# I2C support
-+#
-+# CONFIG_I2C is not set
-+
-+#
-+# SPI support
-+#
-+CONFIG_SPI=y
-+# CONFIG_SPI_DEBUG is not set
-+CONFIG_SPI_MASTER=y
-+
-+#
-+# SPI Master Controller Drivers
-+#
-+CONFIG_SPI_ATMEL=y
-+# CONFIG_SPI_BITBANG is not set
-+
-+#
-+# SPI Protocol Masters
-+#
-+
-+#
-+# Dallas's 1-wire bus
-+#
-+# CONFIG_W1 is not set
-+
-+#
-+# Hardware Monitoring support
-+#
-+# CONFIG_HWMON is not set
-+# CONFIG_HWMON_VID is not set
-+
-+#
-+# Misc devices
-+#
-+# CONFIG_TIFM_CORE is not set
-+
-+#
-+# LED devices
-+#
-+# CONFIG_NEW_LEDS is not set
-+
-+#
-+# LED drivers
-+#
-+
-+#
-+# LED Triggers
-+#
-+
-+#
-+# Multimedia devices
-+#
-+# CONFIG_VIDEO_DEV is not set
-+
-+#
-+# Digital Video Broadcasting Devices
-+#
-+# CONFIG_DVB is not set
-+
-+#
-+# Graphics support
-+#
-+# CONFIG_FIRMWARE_EDID is not set
-+# CONFIG_FB is not set
-+
-+#
-+# Console display driver support
-+#
-+# CONFIG_VGA_CONSOLE is not set
-+CONFIG_DUMMY_CONSOLE=y
-+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-+
-+#
-+# Sound
-+#
-+# CONFIG_SOUND is not set
-+
-+#
-+# HID Devices
-+#
-+# CONFIG_HID is not set
-+
-+#
-+# USB support
-+#
-+CONFIG_USB_ARCH_HAS_HCD=y
-+CONFIG_USB_ARCH_HAS_OHCI=y
-+# CONFIG_USB_ARCH_HAS_EHCI is not set
-+# CONFIG_USB is not set
-+
-+#
-+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
-+#
-+
-+#
-+# USB Gadget Support
-+#
-+# CONFIG_USB_GADGET is not set
-+
-+#
-+# MMC/SD Card support
-+#
-+# CONFIG_MMC is not set
-+
-+#
-+# Real Time Clock
-+#
-+CONFIG_RTC_LIB=y
-+# CONFIG_RTC_CLASS is not set
-+
-+#
-+# File systems
-+#
-+CONFIG_EXT2_FS=y
-+# CONFIG_EXT2_FS_XATTR is not set
-+# CONFIG_EXT2_FS_XIP is not set
-+CONFIG_EXT3_FS=y
-+CONFIG_EXT3_FS_XATTR=y
-+# CONFIG_EXT3_FS_POSIX_ACL is not set
-+# CONFIG_EXT3_FS_SECURITY is not set
-+# CONFIG_EXT4DEV_FS is not set
-+CONFIG_JBD=y
-+# CONFIG_JBD_DEBUG is not set
-+CONFIG_FS_MBCACHE=y
-+# CONFIG_REISERFS_FS is not set
-+# CONFIG_JFS_FS is not set
-+# CONFIG_FS_POSIX_ACL is not set
-+# CONFIG_XFS_FS is not set
-+# CONFIG_GFS2_FS is not set
-+# CONFIG_OCFS2_FS is not set
-+# CONFIG_MINIX_FS is not set
-+# CONFIG_ROMFS_FS is not set
-+CONFIG_INOTIFY=y
-+CONFIG_INOTIFY_USER=y
-+# CONFIG_QUOTA is not set
-+CONFIG_DNOTIFY=y
-+# CONFIG_AUTOFS_FS is not set
-+CONFIG_AUTOFS4_FS=y
-+# CONFIG_FUSE_FS is not set
-+
-+#
-+# CD-ROM/DVD Filesystems
-+#
-+# CONFIG_ISO9660_FS is not set
-+# CONFIG_UDF_FS is not set
-+
-+#
-+# DOS/FAT/NT Filesystems
-+#
-+CONFIG_FAT_FS=y
-+# CONFIG_MSDOS_FS is not set
-+CONFIG_VFAT_FS=y
-+CONFIG_FAT_DEFAULT_CODEPAGE=437
-+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
-+# CONFIG_NTFS_FS is not set
-+
-+#
-+# Pseudo filesystems
-+#
-+CONFIG_PROC_FS=y
-+CONFIG_PROC_SYSCTL=y
-+CONFIG_SYSFS=y
-+CONFIG_TMPFS=y
-+# CONFIG_TMPFS_POSIX_ACL is not set
-+# CONFIG_HUGETLB_PAGE is not set
-+CONFIG_RAMFS=y
-+# CONFIG_CONFIGFS_FS is not set
-+
-+#
-+# Miscellaneous filesystems
-+#
-+# CONFIG_ADFS_FS is not set
-+# CONFIG_AFFS_FS is not set
-+# CONFIG_HFS_FS is not set
-+# CONFIG_HFSPLUS_FS is not set
-+# CONFIG_BEFS_FS is not set
-+# CONFIG_BFS_FS is not set
-+# CONFIG_EFS_FS is not set
-+CONFIG_JFFS2_FS=y
-+CONFIG_JFFS2_FS_DEBUG=0
-+CONFIG_JFFS2_FS_WRITEBUFFER=y
-+# CONFIG_JFFS2_SUMMARY is not set
-+# CONFIG_JFFS2_FS_XATTR is not set
-+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
-+CONFIG_JFFS2_ZLIB=y
-+CONFIG_JFFS2_RTIME=y
-+# CONFIG_JFFS2_RUBIN is not set
-+CONFIG_CRAMFS=y
-+# CONFIG_VXFS_FS is not set
-+# CONFIG_HPFS_FS is not set
-+# CONFIG_QNX4FS_FS is not set
-+# CONFIG_SYSV_FS is not set
-+# CONFIG_UFS_FS is not set
-+
-+#
-+# Network File Systems
-+#
-+CONFIG_NFS_FS=y
-+CONFIG_NFS_V3=y
-+# CONFIG_NFS_V3_ACL is not set
-+# CONFIG_NFS_V4 is not set
-+# CONFIG_NFS_DIRECTIO is not set
-+# CONFIG_NFSD is not set
-+CONFIG_ROOT_NFS=y
-+CONFIG_LOCKD=y
-+CONFIG_LOCKD_V4=y
-+CONFIG_NFS_COMMON=y
-+CONFIG_SUNRPC=y
-+# CONFIG_RPCSEC_GSS_KRB5 is not set
-+# CONFIG_RPCSEC_GSS_SPKM3 is not set
-+# CONFIG_SMB_FS is not set
-+# CONFIG_CIFS is not set
-+# CONFIG_NCP_FS is not set
-+# CONFIG_CODA_FS is not set
-+# CONFIG_AFS_FS is not set
-+# CONFIG_9P_FS is not set
-+
-+#
-+# Partition Types
-+#
-+# CONFIG_PARTITION_ADVANCED is not set
-+CONFIG_MSDOS_PARTITION=y
-+
-+#
-+# Native Language Support
-+#
-+CONFIG_NLS=y
-+CONFIG_NLS_DEFAULT="iso8859-1"
-+CONFIG_NLS_CODEPAGE_437=y
-+# CONFIG_NLS_CODEPAGE_737 is not set
-+# CONFIG_NLS_CODEPAGE_775 is not set
-+CONFIG_NLS_CODEPAGE_850=y
-+# CONFIG_NLS_CODEPAGE_852 is not set
-+# CONFIG_NLS_CODEPAGE_855 is not set
-+# CONFIG_NLS_CODEPAGE_857 is not set
-+# CONFIG_NLS_CODEPAGE_860 is not set
-+# CONFIG_NLS_CODEPAGE_861 is not set
-+# CONFIG_NLS_CODEPAGE_862 is not set
-+# CONFIG_NLS_CODEPAGE_863 is not set
-+# CONFIG_NLS_CODEPAGE_864 is not set
-+# CONFIG_NLS_CODEPAGE_865 is not set
-+# CONFIG_NLS_CODEPAGE_866 is not set
-+# CONFIG_NLS_CODEPAGE_869 is not set
-+# CONFIG_NLS_CODEPAGE_936 is not set
-+# CONFIG_NLS_CODEPAGE_950 is not set
-+# CONFIG_NLS_CODEPAGE_932 is not set
-+# CONFIG_NLS_CODEPAGE_949 is not set
-+# CONFIG_NLS_CODEPAGE_874 is not set
-+# CONFIG_NLS_ISO8859_8 is not set
-+# CONFIG_NLS_CODEPAGE_1250 is not set
-+# CONFIG_NLS_CODEPAGE_1251 is not set
-+# CONFIG_NLS_ASCII is not set
-+CONFIG_NLS_ISO8859_1=y
-+# CONFIG_NLS_ISO8859_2 is not set
-+# CONFIG_NLS_ISO8859_3 is not set
-+# CONFIG_NLS_ISO8859_4 is not set
-+# CONFIG_NLS_ISO8859_5 is not set
-+# CONFIG_NLS_ISO8859_6 is not set
-+# CONFIG_NLS_ISO8859_7 is not set
-+# CONFIG_NLS_ISO8859_9 is not set
-+# CONFIG_NLS_ISO8859_13 is not set
-+# CONFIG_NLS_ISO8859_14 is not set
-+# CONFIG_NLS_ISO8859_15 is not set
-+# CONFIG_NLS_KOI8_R is not set
-+# CONFIG_NLS_KOI8_U is not set
-+# CONFIG_NLS_UTF8 is not set
-+
-+#
-+# Distributed Lock Manager
-+#
-+# CONFIG_DLM is not set
-+
-+#
-+# Profiling support
-+#
-+# CONFIG_PROFILING is not set
-+
-+#
-+# Kernel hacking
-+#
-+# CONFIG_PRINTK_TIME is not set
-+CONFIG_ENABLE_MUST_CHECK=y
-+# CONFIG_MAGIC_SYSRQ is not set
-+# CONFIG_UNUSED_SYMBOLS is not set
-+# CONFIG_DEBUG_FS is not set
-+# CONFIG_HEADERS_CHECK is not set
-+CONFIG_DEBUG_KERNEL=y
-+CONFIG_LOG_BUF_SHIFT=14
-+CONFIG_DETECT_SOFTLOCKUP=y
-+# CONFIG_SCHEDSTATS is not set
-+# CONFIG_DEBUG_SLAB is not set
-+# CONFIG_DEBUG_RT_MUTEXES is not set
-+# CONFIG_RT_MUTEX_TESTER is not set
-+# CONFIG_DEBUG_SPINLOCK is not set
-+# CONFIG_DEBUG_MUTEXES is not set
-+# CONFIG_DEBUG_RWSEMS is not set
-+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
-+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
-+# CONFIG_DEBUG_KOBJECT is not set
-+CONFIG_DEBUG_BUGVERBOSE=y
-+# CONFIG_DEBUG_INFO is not set
-+# CONFIG_DEBUG_VM is not set
-+# CONFIG_DEBUG_LIST is not set
-+CONFIG_FRAME_POINTER=y
-+CONFIG_FORCED_INLINING=y
-+# CONFIG_RCU_TORTURE_TEST is not set
-+CONFIG_DEBUG_USER=y
-+# CONFIG_DEBUG_ERRORS is not set
-+CONFIG_DEBUG_LL=y
-+# CONFIG_DEBUG_ICEDCC is not set
-+
-+#
-+# Security options
-+#
-+# CONFIG_KEYS is not set
-+# CONFIG_SECURITY is not set
-+
-+#
-+# Cryptographic options
-+#
-+# CONFIG_CRYPTO is not set
-+
-+#
-+# Library routines
-+#
-+CONFIG_BITREVERSE=y
-+# CONFIG_CRC_CCITT is not set
-+# CONFIG_CRC16 is not set
-+CONFIG_CRC32=y
-+# CONFIG_LIBCRC32C is not set
-+CONFIG_ZLIB_INFLATE=y
-+CONFIG_ZLIB_DEFLATE=y
-+CONFIG_PLIST=y
-+CONFIG_IOMAP_COPY=y
-Index: linux-2.6.22.19/arch/arm/configs/kb9202_defconfig
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/configs/kb9202_defconfig
-+++ linux-2.6.22.19/arch/arm/configs/kb9202_defconfig
-@@ -1,19 +1,31 @@
- #
- # Automatically generated make config: don't edit
--# Linux kernel version: 2.6.13-rc2
--# Sun Aug 14 19:26:59 2005
-+# Linux kernel version: 2.6.21
-+# Mon May 7 11:43:14 2007
- #
- CONFIG_ARM=y
-+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-+CONFIG_GENERIC_GPIO=y
-+# CONFIG_GENERIC_TIME is not set
- CONFIG_MMU=y
--CONFIG_UID16=y
-+# CONFIG_NO_IOPORT is not set
-+CONFIG_GENERIC_HARDIRQS=y
-+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-+CONFIG_HARDIRQS_SW_RESEND=y
-+CONFIG_GENERIC_IRQ_PROBE=y
- CONFIG_RWSEM_GENERIC_SPINLOCK=y
-+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-+CONFIG_GENERIC_HWEIGHT=y
- CONFIG_GENERIC_CALIBRATE_DELAY=y
-+CONFIG_ZONE_DMA=y
-+CONFIG_VECTORS_BASE=0xffff0000
-+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
- #
- # Code maturity level options
- #
--# CONFIG_EXPERIMENTAL is not set
--CONFIG_CLEAN_COMPILE=y
-+CONFIG_EXPERIMENTAL=y
- CONFIG_BROKEN_ON_SMP=y
- CONFIG_INIT_ENV_ARG_LIMIT=32
-
-@@ -21,54 +33,103 @@ CONFIG_INIT_ENV_ARG_LIMIT=32
- # General setup
- #
- CONFIG_LOCALVERSION=""
--# CONFIG_SWAP is not set
--# CONFIG_SYSVIPC is not set
--# CONFIG_BSD_PROCESS_ACCT is not set
-+CONFIG_LOCALVERSION_AUTO=y
-+CONFIG_SWAP=y
-+CONFIG_SYSVIPC=y
-+# CONFIG_IPC_NS is not set
-+CONFIG_SYSVIPC_SYSCTL=y
-+CONFIG_POSIX_MQUEUE=y
-+CONFIG_BSD_PROCESS_ACCT=y
-+# CONFIG_BSD_PROCESS_ACCT_V3 is not set
-+# CONFIG_TASKSTATS is not set
-+# CONFIG_UTS_NS is not set
-+CONFIG_AUDIT=y
-+CONFIG_IKCONFIG=y
-+CONFIG_IKCONFIG_PROC=y
-+CONFIG_SYSFS_DEPRECATED=y
-+# CONFIG_RELAY is not set
-+CONFIG_BLK_DEV_INITRD=y
-+CONFIG_INITRAMFS_SOURCE=""
-+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
- CONFIG_SYSCTL=y
--# CONFIG_AUDIT is not set
--CONFIG_HOTPLUG=y
--# CONFIG_KOBJECT_UEVENT is not set
--# CONFIG_IKCONFIG is not set
- # CONFIG_EMBEDDED is not set
-+CONFIG_UID16=y
-+CONFIG_SYSCTL_SYSCALL=y
- CONFIG_KALLSYMS=y
- # CONFIG_KALLSYMS_ALL is not set
--# CONFIG_KALLSYMS_EXTRA_PASS is not set
-+CONFIG_KALLSYMS_EXTRA_PASS=y
-+CONFIG_HOTPLUG=y
- CONFIG_PRINTK=y
- CONFIG_BUG=y
-+CONFIG_ELF_CORE=y
- CONFIG_BASE_FULL=y
- CONFIG_FUTEX=y
- CONFIG_EPOLL=y
--CONFIG_CC_OPTIMIZE_FOR_SIZE=y
- CONFIG_SHMEM=y
--CONFIG_CC_ALIGN_FUNCTIONS=0
--CONFIG_CC_ALIGN_LABELS=0
--CONFIG_CC_ALIGN_LOOPS=0
--CONFIG_CC_ALIGN_JUMPS=0
-+CONFIG_SLAB=y
-+CONFIG_VM_EVENT_COUNTERS=y
-+CONFIG_RT_MUTEXES=y
- # CONFIG_TINY_SHMEM is not set
- CONFIG_BASE_SMALL=0
-+# CONFIG_SLOB is not set
-
- #
- # Loadable module support
- #
- CONFIG_MODULES=y
- CONFIG_MODULE_UNLOAD=y
--CONFIG_OBSOLETE_MODPARM=y
--# CONFIG_MODULE_SRCVERSION_ALL is not set
-+# CONFIG_MODULE_FORCE_UNLOAD is not set
-+CONFIG_MODVERSIONS=y
-+CONFIG_MODULE_SRCVERSION_ALL=y
- CONFIG_KMOD=y
-
- #
-+# Block layer
-+#
-+CONFIG_BLOCK=y
-+CONFIG_LBD=y
-+# CONFIG_BLK_DEV_IO_TRACE is not set
-+# CONFIG_LSF is not set
-+
-+#
-+# IO Schedulers
-+#
-+CONFIG_IOSCHED_NOOP=y
-+CONFIG_IOSCHED_AS=y
-+CONFIG_IOSCHED_DEADLINE=y
-+CONFIG_IOSCHED_CFQ=y
-+# CONFIG_DEFAULT_AS is not set
-+# CONFIG_DEFAULT_DEADLINE is not set
-+CONFIG_DEFAULT_CFQ=y
-+# CONFIG_DEFAULT_NOOP is not set
-+CONFIG_DEFAULT_IOSCHED="cfq"
-+
-+#
- # System Type
- #
-+# CONFIG_ARCH_AAEC2000 is not set
-+# CONFIG_ARCH_INTEGRATOR is not set
-+# CONFIG_ARCH_REALVIEW is not set
-+# CONFIG_ARCH_VERSATILE is not set
-+CONFIG_ARCH_AT91=y
- # CONFIG_ARCH_CLPS7500 is not set
- # CONFIG_ARCH_CLPS711X is not set
- # CONFIG_ARCH_CO285 is not set
- # CONFIG_ARCH_EBSA110 is not set
-+# CONFIG_ARCH_EP93XX is not set
- # CONFIG_ARCH_FOOTBRIDGE is not set
--# CONFIG_ARCH_INTEGRATOR is not set
--# CONFIG_ARCH_IOP3XX is not set
-+# CONFIG_ARCH_NETX is not set
-+# CONFIG_ARCH_H720X is not set
-+# CONFIG_ARCH_IMX is not set
-+# CONFIG_ARCH_IOP32X is not set
-+# CONFIG_ARCH_IOP33X is not set
-+# CONFIG_ARCH_IOP13XX is not set
- # CONFIG_ARCH_IXP4XX is not set
- # CONFIG_ARCH_IXP2000 is not set
-+# CONFIG_ARCH_IXP23XX is not set
- # CONFIG_ARCH_L7200 is not set
-+# CONFIG_ARCH_NS9XXX is not set
-+# CONFIG_ARCH_PNX4008 is not set
- # CONFIG_ARCH_PXA is not set
- # CONFIG_ARCH_RPC is not set
- # CONFIG_ARCH_SA1100 is not set
-@@ -76,34 +137,52 @@ CONFIG_KMOD=y
- # CONFIG_ARCH_SHARK is not set
- # CONFIG_ARCH_LH7A40X is not set
- # CONFIG_ARCH_OMAP is not set
--# CONFIG_ARCH_VERSATILE is not set
--# CONFIG_ARCH_IMX is not set
--# CONFIG_ARCH_H720X is not set
--# CONFIG_ARCH_AAEC2000 is not set
--CONFIG_ARCH_AT91=y
-+
-+#
-+# Atmel AT91 System-on-Chip
-+#
- CONFIG_ARCH_AT91RM9200=y
-+# CONFIG_ARCH_AT91SAM9260 is not set
-+# CONFIG_ARCH_AT91SAM9261 is not set
-+# CONFIG_ARCH_AT91SAM9263 is not set
-
- #
--# AT91RM9200 Implementations
-+# AT91RM9200 Board Type
- #
-+# CONFIG_MACH_ONEARM is not set
- # CONFIG_ARCH_AT91RM9200DK is not set
- # CONFIG_MACH_AT91RM9200EK is not set
- # CONFIG_MACH_CSB337 is not set
- # CONFIG_MACH_CSB637 is not set
- # CONFIG_MACH_CARMEVA is not set
-+# CONFIG_MACH_ATEB9200 is not set
- CONFIG_MACH_KB9200=y
-+# CONFIG_MACH_KAFA is not set
-+# CONFIG_MACH_CHUB is not set
-+
-+#
-+# AT91 Board Options
-+#
-+
-+#
-+# AT91 Feature Selections
-+#
-+# CONFIG_AT91_PROGRAMMABLE_CLOCKS is not set
-+# CONFIG_ATMEL_TCLIB is not set
-
- #
- # Processor Type
- #
- CONFIG_CPU_32=y
- CONFIG_CPU_ARM920T=y
--CONFIG_CPU_32v4=y
-+CONFIG_CPU_32v4T=y
- CONFIG_CPU_ABRT_EV4T=y
- CONFIG_CPU_CACHE_V4WT=y
- CONFIG_CPU_CACHE_VIVT=y
- CONFIG_CPU_COPY_V4WB=y
- CONFIG_CPU_TLB_V4WBI=y
-+CONFIG_CPU_CP15=y
-+CONFIG_CPU_CP15_MMU=y
-
- #
- # Processor Features
-@@ -112,24 +191,44 @@ CONFIG_ARM_THUMB=y
- # CONFIG_CPU_ICACHE_DISABLE is not set
- # CONFIG_CPU_DCACHE_DISABLE is not set
- # CONFIG_CPU_DCACHE_WRITETHROUGH is not set
-+# CONFIG_OUTER_CACHE is not set
-
- #
- # Bus support
- #
--CONFIG_ISA_DMA_API=y
-
- #
- # PCCARD (PCMCIA/CardBus) support
- #
--# CONFIG_PCCARD is not set
-+CONFIG_PCCARD=m
-+# CONFIG_PCMCIA_DEBUG is not set
-+CONFIG_PCMCIA=m
-+CONFIG_PCMCIA_LOAD_CIS=y
-+CONFIG_PCMCIA_IOCTL=y
-+
-+#
-+# PC-card bridges
-+#
-+# CONFIG_AT91_CF is not set
-
- #
- # Kernel Features
- #
-+# CONFIG_PREEMPT is not set
- # CONFIG_NO_IDLE_HZ is not set
-+CONFIG_HZ=100
-+# CONFIG_AEABI is not set
- # CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
-+CONFIG_SELECT_MEMORY_MODEL=y
-+CONFIG_FLATMEM_MANUAL=y
-+# CONFIG_DISCONTIGMEM_MANUAL is not set
-+# CONFIG_SPARSEMEM_MANUAL is not set
- CONFIG_FLATMEM=y
- CONFIG_FLAT_NODE_MEM_MAP=y
-+# CONFIG_SPARSEMEM_STATIC is not set
-+CONFIG_SPLIT_PTLOCK_CPUS=4096
-+# CONFIG_RESOURCES_64BIT is not set
-+CONFIG_ZONE_DMA_FLAG=1
- # CONFIG_LEDS is not set
- CONFIG_ALIGNMENT_TRAP=y
-
-@@ -138,8 +237,10 @@ CONFIG_ALIGNMENT_TRAP=y
- #
- CONFIG_ZBOOT_ROM_TEXT=0x10000000
- CONFIG_ZBOOT_ROM_BSS=0x20040000
--CONFIG_ZBOOT_ROM=y
--CONFIG_CMDLINE="console=ttyS0,115200 root=/dev/ram rw initrd=0x20210000,654933"
-+# CONFIG_ZBOOT_ROM is not set
-+CONFIG_CMDLINE="noinitrd root=/dev/mtdblock0 rootfstype=jffs2 mem=64M"
-+# CONFIG_XIP_KERNEL is not set
-+# CONFIG_KEXEC is not set
-
- #
- # Floating point emulation
-@@ -150,6 +251,7 @@ CONFIG_CMDLINE="console=ttyS0,115200 roo
- #
- CONFIG_FPE_NWFPE=y
- # CONFIG_FPE_NWFPE_XP is not set
-+# CONFIG_FPE_FASTFPE is not set
-
- #
- # Userspace binary formats
-@@ -165,6 +267,96 @@ CONFIG_BINFMT_MISC=y
- # CONFIG_PM is not set
-
- #
-+# Networking
-+#
-+CONFIG_NET=y
-+
-+#
-+# Networking options
-+#
-+# CONFIG_NETDEBUG is not set
-+CONFIG_PACKET=y
-+# CONFIG_PACKET_MMAP is not set
-+CONFIG_UNIX=y
-+# CONFIG_NET_KEY is not set
-+CONFIG_INET=y
-+CONFIG_IP_MULTICAST=y
-+# CONFIG_IP_ADVANCED_ROUTER is not set
-+CONFIG_IP_FIB_HASH=y
-+CONFIG_IP_PNP=y
-+# CONFIG_IP_PNP_DHCP is not set
-+# CONFIG_IP_PNP_BOOTP is not set
-+# CONFIG_IP_PNP_RARP is not set
-+# CONFIG_NET_IPIP is not set
-+# CONFIG_NET_IPGRE is not set
-+# CONFIG_IP_MROUTE is not set
-+# CONFIG_ARPD is not set
-+# CONFIG_SYN_COOKIES is not set
-+# CONFIG_INET_AH is not set
-+# CONFIG_INET_ESP is not set
-+# CONFIG_INET_IPCOMP is not set
-+# CONFIG_INET_XFRM_TUNNEL is not set
-+# CONFIG_INET_TUNNEL is not set
-+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-+# CONFIG_INET_XFRM_MODE_BEET is not set
-+# CONFIG_INET_DIAG is not set
-+# CONFIG_TCP_CONG_ADVANCED is not set
-+CONFIG_TCP_CONG_CUBIC=y
-+CONFIG_DEFAULT_TCP_CONG="cubic"
-+# CONFIG_TCP_MD5SIG is not set
-+# CONFIG_IPV6 is not set
-+# CONFIG_INET6_XFRM_TUNNEL is not set
-+# CONFIG_INET6_TUNNEL is not set
-+# CONFIG_NETWORK_SECMARK is not set
-+# CONFIG_NETFILTER is not set
-+
-+#
-+# DCCP Configuration (EXPERIMENTAL)
-+#
-+# CONFIG_IP_DCCP is not set
-+
-+#
-+# SCTP Configuration (EXPERIMENTAL)
-+#
-+CONFIG_IP_SCTP=m
-+# CONFIG_SCTP_DBG_MSG is not set
-+# CONFIG_SCTP_DBG_OBJCNT is not set
-+# CONFIG_SCTP_HMAC_NONE is not set
-+# CONFIG_SCTP_HMAC_SHA1 is not set
-+CONFIG_SCTP_HMAC_MD5=y
-+
-+#
-+# TIPC Configuration (EXPERIMENTAL)
-+#
-+# CONFIG_TIPC is not set
-+# CONFIG_ATM is not set
-+# CONFIG_BRIDGE is not set
-+# CONFIG_VLAN_8021Q is not set
-+# CONFIG_DECNET is not set
-+# CONFIG_LLC2 is not set
-+# CONFIG_IPX is not set
-+# CONFIG_ATALK is not set
-+# CONFIG_X25 is not set
-+# CONFIG_LAPB is not set
-+# CONFIG_ECONET is not set
-+# CONFIG_WAN_ROUTER is not set
-+
-+#
-+# QoS and/or fair queueing
-+#
-+# CONFIG_NET_SCHED is not set
-+
-+#
-+# Network testing
-+#
-+# CONFIG_NET_PKTGEN is not set
-+# CONFIG_HAMRADIO is not set
-+# CONFIG_IRDA is not set
-+# CONFIG_BT is not set
-+# CONFIG_IEEE80211 is not set
-+
-+#
- # Device Drivers
- #
-
-@@ -173,13 +365,95 @@ CONFIG_BINFMT_MISC=y
- #
- CONFIG_STANDALONE=y
- CONFIG_PREVENT_FIRMWARE_BUILD=y
--# CONFIG_FW_LOADER is not set
--CONFIG_DEBUG_DRIVER=y
-+CONFIG_FW_LOADER=y
-+# CONFIG_DEBUG_DRIVER is not set
-+# CONFIG_DEBUG_DEVRES is not set
-+# CONFIG_SYS_HYPERVISOR is not set
-+
-+#
-+# Connector - unified userspace <-> kernelspace linker
-+#
-+# CONFIG_CONNECTOR is not set
-
- #
- # Memory Technology Devices (MTD)
- #
--# CONFIG_MTD is not set
-+CONFIG_MTD=y
-+# CONFIG_MTD_DEBUG is not set
-+CONFIG_MTD_CONCAT=y
-+CONFIG_MTD_PARTITIONS=y
-+# CONFIG_MTD_REDBOOT_PARTS is not set
-+CONFIG_MTD_CMDLINE_PARTS=y
-+# CONFIG_MTD_AFS_PARTS is not set
-+
-+#
-+# User Modules And Translation Layers
-+#
-+CONFIG_MTD_CHAR=y
-+CONFIG_MTD_BLKDEVS=y
-+CONFIG_MTD_BLOCK=y
-+# CONFIG_FTL is not set
-+# CONFIG_NFTL is not set
-+# CONFIG_INFTL is not set
-+# CONFIG_RFD_FTL is not set
-+# CONFIG_SSFDC is not set
-+
-+#
-+# RAM/ROM/Flash chip drivers
-+#
-+# CONFIG_MTD_CFI is not set
-+# CONFIG_MTD_JEDECPROBE is not set
-+CONFIG_MTD_MAP_BANK_WIDTH_1=y
-+CONFIG_MTD_MAP_BANK_WIDTH_2=y
-+CONFIG_MTD_MAP_BANK_WIDTH_4=y
-+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
-+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
-+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
-+CONFIG_MTD_CFI_I1=y
-+CONFIG_MTD_CFI_I2=y
-+# CONFIG_MTD_CFI_I4 is not set
-+# CONFIG_MTD_CFI_I8 is not set
-+# CONFIG_MTD_RAM is not set
-+# CONFIG_MTD_ROM is not set
-+# CONFIG_MTD_ABSENT is not set
-+# CONFIG_MTD_OBSOLETE_CHIPS is not set
-+
-+#
-+# Mapping drivers for chip access
-+#
-+CONFIG_MTD_COMPLEX_MAPPINGS=y
-+# CONFIG_MTD_PLATRAM is not set
-+
-+#
-+# Self-contained MTD device drivers
-+#
-+# CONFIG_MTD_SLRAM is not set
-+# CONFIG_MTD_PHRAM is not set
-+# CONFIG_MTD_MTDRAM is not set
-+# CONFIG_MTD_BLOCK2MTD is not set
-+
-+#
-+# Disk-On-Chip Device Drivers
-+#
-+# CONFIG_MTD_DOC2000 is not set
-+# CONFIG_MTD_DOC2001 is not set
-+# CONFIG_MTD_DOC2001PLUS is not set
-+
-+#
-+# NAND Flash Device Drivers
-+#
-+CONFIG_MTD_NAND=y
-+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
-+# CONFIG_MTD_NAND_ECC_SMC is not set
-+CONFIG_MTD_NAND_IDS=y
-+# CONFIG_MTD_NAND_DISKONCHIP is not set
-+CONFIG_MTD_NAND_AT91=y
-+# CONFIG_MTD_NAND_NANDSIM is not set
-+
-+#
-+# OneNAND Flash Device Drivers
-+#
-+# CONFIG_MTD_ONENAND is not set
-
- #
- # Parallel port support
-@@ -189,6 +463,7 @@ CONFIG_DEBUG_DRIVER=y
- #
- # Plug and Play support
- #
-+# CONFIG_PNPACPI is not set
-
- #
- # Block devices
-@@ -196,28 +471,27 @@ CONFIG_DEBUG_DRIVER=y
- # CONFIG_BLK_DEV_COW_COMMON is not set
- CONFIG_BLK_DEV_LOOP=y
- # CONFIG_BLK_DEV_CRYPTOLOOP is not set
--CONFIG_BLK_DEV_NBD=y
-+# CONFIG_BLK_DEV_NBD is not set
- # CONFIG_BLK_DEV_UB is not set
- CONFIG_BLK_DEV_RAM=y
- CONFIG_BLK_DEV_RAM_COUNT=16
--CONFIG_BLK_DEV_RAM_SIZE=4096
--CONFIG_BLK_DEV_INITRD=y
--CONFIG_INITRAMFS_SOURCE=""
-+CONFIG_BLK_DEV_RAM_SIZE=16384
-+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
- # CONFIG_CDROM_PKTCDVD is not set
-+# CONFIG_ATA_OVER_ETH is not set
-
- #
--# IO Schedulers
-+# ATA/ATAPI/MFM/RLL support
- #
--CONFIG_IOSCHED_NOOP=y
--CONFIG_IOSCHED_AS=y
--CONFIG_IOSCHED_DEADLINE=y
--CONFIG_IOSCHED_CFQ=y
--# CONFIG_ATA_OVER_ETH is not set
-+# CONFIG_IDE is not set
-
- #
- # SCSI device support
- #
-+# CONFIG_RAID_ATTRS is not set
- CONFIG_SCSI=y
-+# CONFIG_SCSI_TGT is not set
-+# CONFIG_SCSI_NETLINK is not set
- CONFIG_SCSI_PROC_FS=y
-
- #
-@@ -233,97 +507,61 @@ CONFIG_CHR_DEV_SG=y
- #
- # Some SCSI devices (e.g. CD jukebox) support multiple LUNs
- #
--# CONFIG_SCSI_MULTI_LUN is not set
--# CONFIG_SCSI_CONSTANTS is not set
--# CONFIG_SCSI_LOGGING is not set
-+CONFIG_SCSI_MULTI_LUN=y
-+CONFIG_SCSI_CONSTANTS=y
-+CONFIG_SCSI_LOGGING=y
-+# CONFIG_SCSI_SCAN_ASYNC is not set
-
- #
--# SCSI Transport Attributes
-+# SCSI Transports
- #
--# CONFIG_SCSI_SPI_ATTRS is not set
-+CONFIG_SCSI_SPI_ATTRS=m
- # CONFIG_SCSI_FC_ATTRS is not set
- # CONFIG_SCSI_ISCSI_ATTRS is not set
-+# CONFIG_SCSI_SAS_ATTRS is not set
-+# CONFIG_SCSI_SAS_LIBSAS is not set
-
- #
- # SCSI low-level drivers
- #
--# CONFIG_SCSI_SATA is not set
-+# CONFIG_ISCSI_TCP is not set
- # CONFIG_SCSI_DEBUG is not set
-
- #
--# Multi-device support (RAID and LVM)
--#
--# CONFIG_MD is not set
--
--#
--# Fusion MPT device support
-+# PCMCIA SCSI adapter support
- #
--# CONFIG_FUSION is not set
-+# CONFIG_PCMCIA_AHA152X is not set
-+# CONFIG_PCMCIA_FDOMAIN is not set
-+# CONFIG_PCMCIA_NINJA_SCSI is not set
-+# CONFIG_PCMCIA_QLOGIC is not set
-+# CONFIG_PCMCIA_SYM53C500 is not set
-
- #
--# IEEE 1394 (FireWire) support
-+# Serial ATA (prod) and Parallel ATA (experimental) drivers
- #
-+# CONFIG_ATA is not set
-
- #
--# I2O device support
-+# Multi-device support (RAID and LVM)
- #
-+# CONFIG_MD is not set
-
- #
--# Networking support
-+# Fusion MPT device support
- #
--CONFIG_NET=y
-+# CONFIG_FUSION is not set
-
- #
--# Networking options
-+# IEEE 1394 (FireWire) support
- #
--CONFIG_PACKET=y
--# CONFIG_PACKET_MMAP is not set
--CONFIG_UNIX=y
--# CONFIG_NET_KEY is not set
--CONFIG_INET=y
--CONFIG_IP_MULTICAST=y
--# CONFIG_IP_ADVANCED_ROUTER is not set
--CONFIG_IP_FIB_HASH=y
--CONFIG_IP_PNP=y
--CONFIG_IP_PNP_DHCP=y
--# CONFIG_IP_PNP_BOOTP is not set
--# CONFIG_IP_PNP_RARP is not set
--# CONFIG_NET_IPIP is not set
--# CONFIG_NET_IPGRE is not set
--# CONFIG_IP_MROUTE is not set
--# CONFIG_SYN_COOKIES is not set
--# CONFIG_INET_AH is not set
--# CONFIG_INET_ESP is not set
--# CONFIG_INET_IPCOMP is not set
--# CONFIG_INET_TUNNEL is not set
--# CONFIG_IP_TCPDIAG is not set
--# CONFIG_IP_TCPDIAG_IPV6 is not set
--# CONFIG_TCP_CONG_ADVANCED is not set
--CONFIG_TCP_CONG_BIC=y
--# CONFIG_IPV6 is not set
--# CONFIG_NETFILTER is not set
--# CONFIG_BRIDGE is not set
--# CONFIG_VLAN_8021Q is not set
--# CONFIG_DECNET is not set
--# CONFIG_LLC2 is not set
--# CONFIG_IPX is not set
--# CONFIG_ATALK is not set
-
- #
--# QoS and/or fair queueing
-+# I2O device support
- #
--# CONFIG_NET_SCHED is not set
--# CONFIG_NET_CLS_ROUTE is not set
-
- #
--# Network testing
-+# Network device support
- #
--# CONFIG_NET_PKTGEN is not set
--# CONFIG_NETPOLL is not set
--# CONFIG_NET_POLL_CONTROLLER is not set
--# CONFIG_HAMRADIO is not set
--# CONFIG_IRDA is not set
--# CONFIG_BT is not set
- CONFIG_NETDEVICES=y
- # CONFIG_DUMMY is not set
- # CONFIG_BONDING is not set
-@@ -331,6 +569,11 @@ CONFIG_NETDEVICES=y
- # CONFIG_TUN is not set
-
- #
-+# PHY device support
-+#
-+# CONFIG_PHYLIB is not set
-+
-+#
- # Ethernet (10 or 100Mbit)
- #
- CONFIG_NET_ETHERNET=y
-@@ -357,11 +600,20 @@ CONFIG_ARM_AT91_ETHER=y
- # CONFIG_NET_RADIO is not set
-
- #
-+# PCMCIA network device support
-+#
-+# CONFIG_NET_PCMCIA is not set
-+
-+#
- # Wan interfaces
- #
- # CONFIG_WAN is not set
- # CONFIG_PPP is not set
- # CONFIG_SLIP is not set
-+# CONFIG_SHAPER is not set
-+# CONFIG_NETCONSOLE is not set
-+# CONFIG_NETPOLL is not set
-+# CONFIG_NET_POLL_CONTROLLER is not set
-
- #
- # ISDN subsystem
-@@ -372,6 +624,7 @@ CONFIG_ARM_AT91_ETHER=y
- # Input device support
- #
- CONFIG_INPUT=y
-+# CONFIG_INPUT_FF_MEMLESS is not set
-
- #
- # Userland interfaces
-@@ -397,9 +650,7 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
- #
- # Hardware I/O ports
- #
--CONFIG_SERIO=y
--# CONFIG_SERIO_SERPORT is not set
--# CONFIG_SERIO_RAW is not set
-+# CONFIG_SERIO is not set
- # CONFIG_GAMEPORT is not set
-
- #
-@@ -408,6 +659,7 @@ CONFIG_SERIO=y
- CONFIG_VT=y
- CONFIG_VT_CONSOLE=y
- CONFIG_HW_CONSOLE=y
-+# CONFIG_VT_HW_CONSOLE_BINDING is not set
- # CONFIG_SERIAL_NONSTANDARD is not set
-
- #
-@@ -420,11 +672,11 @@ CONFIG_HW_CONSOLE=y
- #
- CONFIG_SERIAL_ATMEL=y
- CONFIG_SERIAL_ATMEL_CONSOLE=y
-+# CONFIG_SERIAL_ATMEL_TTYAT is not set
- CONFIG_SERIAL_CORE=y
- CONFIG_SERIAL_CORE_CONSOLE=y
- CONFIG_UNIX98_PTYS=y
--CONFIG_LEGACY_PTYS=y
--CONFIG_LEGACY_PTY_COUNT=256
-+# CONFIG_LEGACY_PTYS is not set
-
- #
- # IPMI
-@@ -435,21 +687,23 @@ CONFIG_LEGACY_PTY_COUNT=256
- # Watchdog Cards
- #
- # CONFIG_WATCHDOG is not set
-+# CONFIG_HW_RANDOM is not set
- # CONFIG_NVRAM is not set
--# CONFIG_RTC is not set
--# CONFIG_AT91RM9200_RTC is not set
- # CONFIG_DTLK is not set
- # CONFIG_R3964 is not set
-
- #
--# Ftape, the floppy tape device driver
-+# PCMCIA character devices
- #
-+# CONFIG_SYNCLINK_CS is not set
-+# CONFIG_CARDMAN_4000 is not set
-+# CONFIG_CARDMAN_4040 is not set
- # CONFIG_RAW_DRIVER is not set
-
- #
- # TPM devices
- #
--# CONFIG_AT91_SPI is not set
-+# CONFIG_TCG_TPM is not set
-
- #
- # I2C support
-@@ -457,10 +711,50 @@ CONFIG_LEGACY_PTY_COUNT=256
- # CONFIG_I2C is not set
-
- #
-+# SPI support
-+#
-+# CONFIG_SPI is not set
-+# CONFIG_SPI_MASTER is not set
-+
-+#
-+# Dallas's 1-wire bus
-+#
-+# CONFIG_W1 is not set
-+
-+#
-+# Hardware Monitoring support
-+#
-+CONFIG_HWMON=y
-+# CONFIG_HWMON_VID is not set
-+# CONFIG_SENSORS_ABITUGURU is not set
-+# CONFIG_SENSORS_F71805F is not set
-+# CONFIG_SENSORS_PC87427 is not set
-+# CONFIG_SENSORS_VT1211 is not set
-+CONFIG_HWMON_DEBUG_CHIP=y
-+
-+#
- # Misc devices
- #
-
- #
-+# Multifunction device drivers
-+#
-+# CONFIG_MFD_SM501 is not set
-+
-+#
-+# LED devices
-+#
-+# CONFIG_NEW_LEDS is not set
-+
-+#
-+# LED drivers
-+#
-+
-+#
-+# LED Triggers
-+#
-+
-+#
- # Multimedia devices
- #
- # CONFIG_VIDEO_DEV is not set
-@@ -469,17 +763,57 @@ CONFIG_LEGACY_PTY_COUNT=256
- # Digital Video Broadcasting Devices
- #
- # CONFIG_DVB is not set
-+# CONFIG_USB_DABUSB is not set
-
- #
- # Graphics support
- #
--# CONFIG_FB is not set
-+CONFIG_BACKLIGHT_LCD_SUPPORT=y
-+CONFIG_BACKLIGHT_CLASS_DEVICE=y
-+# CONFIG_LCD_CLASS_DEVICE is not set
-+CONFIG_BACKLIGHT_KB920x=y
-+CONFIG_FB=y
-+# CONFIG_FIRMWARE_EDID is not set
-+# CONFIG_FB_DDC is not set
-+CONFIG_FB_CFB_FILLRECT=y
-+CONFIG_FB_CFB_COPYAREA=y
-+CONFIG_FB_CFB_IMAGEBLIT=y
-+# CONFIG_FB_SVGALIB is not set
-+# CONFIG_FB_MACMODES is not set
-+# CONFIG_FB_BACKLIGHT is not set
-+CONFIG_FB_MODE_HELPERS=y
-+CONFIG_FB_TILEBLITTING=y
-+
-+#
-+# Frame buffer hardware drivers
-+#
-+CONFIG_FB_S1D15605=y
-+# CONFIG_FB_S1D13XXX is not set
-+# CONFIG_FB_VIRTUAL is not set
-
- #
- # Console display driver support
- #
- # CONFIG_VGA_CONSOLE is not set
- CONFIG_DUMMY_CONSOLE=y
-+CONFIG_FRAMEBUFFER_CONSOLE=y
-+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
-+CONFIG_FONTS=y
-+# CONFIG_FONT_8x8 is not set
-+# CONFIG_FONT_8x16 is not set
-+# CONFIG_FONT_6x11 is not set
-+# CONFIG_FONT_7x14 is not set
-+# CONFIG_FONT_PEARL_8x8 is not set
-+# CONFIG_FONT_ACORN_8x8 is not set
-+CONFIG_FONT_MINI_4x6=y
-+# CONFIG_FONT_SUN8x16 is not set
-+# CONFIG_FONT_SUN12x22 is not set
-+# CONFIG_FONT_10x18 is not set
-+
-+#
-+# Logo configuration
-+#
-+# CONFIG_LOGO is not set
-
- #
- # Sound
-@@ -487,82 +821,98 @@ CONFIG_DUMMY_CONSOLE=y
- # CONFIG_SOUND is not set
-
- #
-+# HID Devices
-+#
-+CONFIG_HID=y
-+# CONFIG_HID_DEBUG is not set
-+
-+#
- # USB support
- #
- CONFIG_USB_ARCH_HAS_HCD=y
- CONFIG_USB_ARCH_HAS_OHCI=y
-+# CONFIG_USB_ARCH_HAS_EHCI is not set
- CONFIG_USB=y
--CONFIG_USB_DEBUG=y
-+# CONFIG_USB_DEBUG is not set
-
- #
- # Miscellaneous USB options
- #
- CONFIG_USB_DEVICEFS=y
-+# CONFIG_USB_DYNAMIC_MINORS is not set
-+# CONFIG_USB_OTG is not set
-
- #
- # USB Host Controller Drivers
- #
- # CONFIG_USB_ISP116X_HCD is not set
- CONFIG_USB_OHCI_HCD=y
--# CONFIG_USB_OHCI_BIG_ENDIAN is not set
-+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
-+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
- CONFIG_USB_OHCI_LITTLE_ENDIAN=y
- # CONFIG_USB_SL811_HCD is not set
-
- #
- # USB Device Class drivers
- #
--# CONFIG_USB_BLUETOOTH_TTY is not set
- # CONFIG_USB_ACM is not set
- # CONFIG_USB_PRINTER is not set
-
- #
--# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information
-+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
-+#
-+
-+#
-+# may also be needed; see USB_STORAGE Help for more information
- #
- CONFIG_USB_STORAGE=y
--CONFIG_USB_STORAGE_DEBUG=y
-+# CONFIG_USB_STORAGE_DEBUG is not set
-+# CONFIG_USB_STORAGE_DATAFAB is not set
- # CONFIG_USB_STORAGE_FREECOM is not set
- # CONFIG_USB_STORAGE_DPCM is not set
-+# CONFIG_USB_STORAGE_USBAT is not set
-+# CONFIG_USB_STORAGE_SDDR09 is not set
-+# CONFIG_USB_STORAGE_SDDR55 is not set
-+# CONFIG_USB_STORAGE_JUMPSHOT is not set
-+# CONFIG_USB_STORAGE_ALAUDA is not set
-+# CONFIG_USB_STORAGE_KARMA is not set
-+CONFIG_USB_LIBUSUAL=y
-
- #
- # USB Input Devices
- #
--# CONFIG_USB_HID is not set
--
--#
--# USB HID Boot Protocol drivers
--#
--# CONFIG_USB_KBD is not set
--# CONFIG_USB_MOUSE is not set
-+CONFIG_USB_HID=y
-+# CONFIG_USB_HIDINPUT_POWERBOOK is not set
-+# CONFIG_HID_FF is not set
-+# CONFIG_USB_HIDDEV is not set
- # CONFIG_USB_AIPTEK is not set
- # CONFIG_USB_WACOM is not set
- # CONFIG_USB_ACECAD is not set
- # CONFIG_USB_KBTAB is not set
- # CONFIG_USB_POWERMATE is not set
--# CONFIG_USB_MTOUCH is not set
--# CONFIG_USB_ITMTOUCH is not set
--# CONFIG_USB_EGALAX is not set
-+# CONFIG_USB_TOUCHSCREEN is not set
-+# CONFIG_USB_YEALINK is not set
- # CONFIG_USB_XPAD is not set
- # CONFIG_USB_ATI_REMOTE is not set
-+# CONFIG_USB_ATI_REMOTE2 is not set
-+# CONFIG_USB_KEYSPAN_REMOTE is not set
-+# CONFIG_USB_APPLETOUCH is not set
-+# CONFIG_USB_GTCO is not set
-
- #
- # USB Imaging devices
- #
-+# CONFIG_USB_MDC800 is not set
- # CONFIG_USB_MICROTEK is not set
-
- #
--# USB Multimedia devices
--#
--# CONFIG_USB_DABUSB is not set
--
--#
--# Video4Linux support is needed for USB Multimedia device support
--#
--
--#
- # USB Network Adapters
- #
-+# CONFIG_USB_CATC is not set
- # CONFIG_USB_KAWETH is not set
- # CONFIG_USB_PEGASUS is not set
-+# CONFIG_USB_RTL8150 is not set
-+# CONFIG_USB_USBNET_MII is not set
- # CONFIG_USB_USBNET is not set
- # CONFIG_USB_MON is not set
-
-@@ -580,12 +930,23 @@ CONFIG_USB_STORAGE_DEBUG=y
- #
- # CONFIG_USB_EMI62 is not set
- # CONFIG_USB_EMI26 is not set
-+# CONFIG_USB_ADUTUX is not set
-+# CONFIG_USB_AUERSWALD is not set
-+# CONFIG_USB_RIO500 is not set
-+# CONFIG_USB_LEGOTOWER is not set
- # CONFIG_USB_LCD is not set
-+# CONFIG_USB_BERRY_CHARGE is not set
- # CONFIG_USB_LED is not set
-+# CONFIG_USB_CYPRESS_CY7C63 is not set
- # CONFIG_USB_CYTHERM is not set
--# CONFIG_USB_PHIDGETKIT is not set
--# CONFIG_USB_PHIDGETSERVO is not set
-+# CONFIG_USB_PHIDGET is not set
- # CONFIG_USB_IDMOUSE is not set
-+# CONFIG_USB_FTDI_ELAN is not set
-+# CONFIG_USB_APPLEDISPLAY is not set
-+# CONFIG_USB_LD is not set
-+# CONFIG_USB_TRANCEVIBRATOR is not set
-+# CONFIG_USB_IOWARRIOR is not set
-+# CONFIG_USB_TEST is not set
-
- #
- # USB DSL modem support
-@@ -599,36 +960,51 @@ CONFIG_USB_STORAGE_DEBUG=y
- #
- # MMC/SD Card support
- #
--# CONFIG_MMC is not set
-+CONFIG_MMC=y
-+# CONFIG_MMC_DEBUG is not set
-+CONFIG_MMC_BLOCK=y
-+CONFIG_MMC_AT91=y
-+
-+#
-+# Real Time Clock
-+#
-+CONFIG_RTC_LIB=y
-+# CONFIG_RTC_CLASS is not set
-
- #
- # File systems
- #
- CONFIG_EXT2_FS=y
- CONFIG_EXT2_FS_XATTR=y
--# CONFIG_EXT2_FS_POSIX_ACL is not set
--# CONFIG_EXT2_FS_SECURITY is not set
-+CONFIG_EXT2_FS_POSIX_ACL=y
-+CONFIG_EXT2_FS_SECURITY=y
- # CONFIG_EXT2_FS_XIP is not set
- CONFIG_EXT3_FS=y
- CONFIG_EXT3_FS_XATTR=y
--# CONFIG_EXT3_FS_POSIX_ACL is not set
--# CONFIG_EXT3_FS_SECURITY is not set
-+CONFIG_EXT3_FS_POSIX_ACL=y
-+CONFIG_EXT3_FS_SECURITY=y
-+# CONFIG_EXT4DEV_FS is not set
- CONFIG_JBD=y
- # CONFIG_JBD_DEBUG is not set
- CONFIG_FS_MBCACHE=y
- # CONFIG_REISERFS_FS is not set
- # CONFIG_JFS_FS is not set
--
--#
--# XFS support
--#
-+CONFIG_FS_POSIX_ACL=y
- # CONFIG_XFS_FS is not set
-+# CONFIG_GFS2_FS is not set
-+# CONFIG_OCFS2_FS is not set
- # CONFIG_MINIX_FS is not set
- # CONFIG_ROMFS_FS is not set
--# CONFIG_QUOTA is not set
-+CONFIG_INOTIFY=y
-+CONFIG_INOTIFY_USER=y
-+CONFIG_QUOTA=y
-+# CONFIG_QFMT_V1 is not set
-+CONFIG_QFMT_V2=y
-+CONFIG_QUOTACTL=y
- CONFIG_DNOTIFY=y
--CONFIG_AUTOFS_FS=y
-+# CONFIG_AUTOFS_FS is not set
- CONFIG_AUTOFS4_FS=y
-+# CONFIG_FUSE_FS is not set
-
- #
- # CD-ROM/DVD Filesystems
-@@ -643,25 +1019,40 @@ CONFIG_FAT_FS=y
- CONFIG_MSDOS_FS=y
- CONFIG_VFAT_FS=y
- CONFIG_FAT_DEFAULT_CODEPAGE=437
--CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
-+CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
- # CONFIG_NTFS_FS is not set
-
- #
- # Pseudo filesystems
- #
- CONFIG_PROC_FS=y
-+CONFIG_PROC_SYSCTL=y
- CONFIG_SYSFS=y
--CONFIG_DEVPTS_FS_XATTR=y
--# CONFIG_DEVPTS_FS_SECURITY is not set
- CONFIG_TMPFS=y
--# CONFIG_TMPFS_XATTR is not set
-+# CONFIG_TMPFS_POSIX_ACL is not set
- # CONFIG_HUGETLB_PAGE is not set
- CONFIG_RAMFS=y
-+CONFIG_CONFIGFS_FS=y
-
- #
- # Miscellaneous filesystems
- #
-+# CONFIG_ADFS_FS is not set
-+# CONFIG_AFFS_FS is not set
-+# CONFIG_HFS_FS is not set
- # CONFIG_HFSPLUS_FS is not set
-+# CONFIG_BEFS_FS is not set
-+# CONFIG_BFS_FS is not set
-+# CONFIG_EFS_FS is not set
-+CONFIG_JFFS2_FS=y
-+CONFIG_JFFS2_FS_DEBUG=0
-+CONFIG_JFFS2_FS_WRITEBUFFER=y
-+# CONFIG_JFFS2_SUMMARY is not set
-+# CONFIG_JFFS2_FS_XATTR is not set
-+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
-+CONFIG_JFFS2_ZLIB=y
-+CONFIG_JFFS2_RTIME=y
-+# CONFIG_JFFS2_RUBIN is not set
- # CONFIG_CRAMFS is not set
- # CONFIG_VXFS_FS is not set
- # CONFIG_HPFS_FS is not set
-@@ -675,16 +1066,23 @@ CONFIG_RAMFS=y
- CONFIG_NFS_FS=y
- CONFIG_NFS_V3=y
- # CONFIG_NFS_V3_ACL is not set
-+CONFIG_NFS_V4=y
-+# CONFIG_NFS_DIRECTIO is not set
- # CONFIG_NFSD is not set
- CONFIG_ROOT_NFS=y
- CONFIG_LOCKD=y
- CONFIG_LOCKD_V4=y
- CONFIG_NFS_COMMON=y
- CONFIG_SUNRPC=y
-+CONFIG_SUNRPC_GSS=y
-+CONFIG_RPCSEC_GSS_KRB5=y
-+# CONFIG_RPCSEC_GSS_SPKM3 is not set
- # CONFIG_SMB_FS is not set
- # CONFIG_CIFS is not set
- # CONFIG_NCP_FS is not set
- # CONFIG_CODA_FS is not set
-+# CONFIG_AFS_FS is not set
-+# CONFIG_9P_FS is not set
-
- #
- # Partition Types
-@@ -734,26 +1132,51 @@ CONFIG_NLS_ASCII=y
- # CONFIG_NLS_ISO8859_15 is not set
- # CONFIG_NLS_KOI8_R is not set
- # CONFIG_NLS_KOI8_U is not set
--# CONFIG_NLS_UTF8 is not set
-+CONFIG_NLS_UTF8=y
-+
-+#
-+# Distributed Lock Manager
-+#
-+# CONFIG_DLM is not set
-+
-+#
-+# Profiling support
-+#
-+# CONFIG_PROFILING is not set
-
- #
- # Kernel hacking
- #
- # CONFIG_PRINTK_TIME is not set
-+CONFIG_ENABLE_MUST_CHECK=y
-+CONFIG_MAGIC_SYSRQ=y
-+# CONFIG_UNUSED_SYMBOLS is not set
-+# CONFIG_DEBUG_FS is not set
-+# CONFIG_HEADERS_CHECK is not set
- CONFIG_DEBUG_KERNEL=y
--# CONFIG_MAGIC_SYSRQ is not set
--CONFIG_LOG_BUF_SHIFT=14
-+# CONFIG_DEBUG_SHIRQ is not set
-+CONFIG_LOG_BUF_SHIFT=17
-+CONFIG_DETECT_SOFTLOCKUP=y
- # CONFIG_SCHEDSTATS is not set
-+# CONFIG_TIMER_STATS is not set
- # CONFIG_DEBUG_SLAB is not set
--# CONFIG_DEBUG_SPINLOCK is not set
--# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
-+# CONFIG_DEBUG_RT_MUTEXES is not set
-+# CONFIG_RT_MUTEX_TESTER is not set
-+CONFIG_DEBUG_SPINLOCK=y
-+# CONFIG_DEBUG_MUTEXES is not set
-+CONFIG_DEBUG_SPINLOCK_SLEEP=y
-+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
- # CONFIG_DEBUG_KOBJECT is not set
- CONFIG_DEBUG_BUGVERBOSE=y
- # CONFIG_DEBUG_INFO is not set
--# CONFIG_DEBUG_FS is not set
-+# CONFIG_DEBUG_VM is not set
-+# CONFIG_DEBUG_LIST is not set
- CONFIG_FRAME_POINTER=y
--CONFIG_DEBUG_USER=y
--CONFIG_DEBUG_ERRORS=y
-+CONFIG_FORCED_INLINING=y
-+# CONFIG_RCU_TORTURE_TEST is not set
-+# CONFIG_FAULT_INJECTION is not set
-+# CONFIG_DEBUG_USER is not set
-+# CONFIG_DEBUG_ERRORS is not set
- CONFIG_DEBUG_LL=y
- # CONFIG_DEBUG_ICEDCC is not set
-
-@@ -766,7 +1189,43 @@ CONFIG_DEBUG_LL=y
- #
- # Cryptographic options
- #
--# CONFIG_CRYPTO is not set
-+CONFIG_CRYPTO=y
-+CONFIG_CRYPTO_ALGAPI=y
-+CONFIG_CRYPTO_BLKCIPHER=y
-+CONFIG_CRYPTO_HASH=m
-+CONFIG_CRYPTO_MANAGER=y
-+CONFIG_CRYPTO_HMAC=m
-+# CONFIG_CRYPTO_XCBC is not set
-+# CONFIG_CRYPTO_NULL is not set
-+# CONFIG_CRYPTO_MD4 is not set
-+CONFIG_CRYPTO_MD5=y
-+# CONFIG_CRYPTO_SHA1 is not set
-+# CONFIG_CRYPTO_SHA256 is not set
-+# CONFIG_CRYPTO_SHA512 is not set
-+# CONFIG_CRYPTO_WP512 is not set
-+# CONFIG_CRYPTO_TGR192 is not set
-+# CONFIG_CRYPTO_GF128MUL is not set
-+# CONFIG_CRYPTO_ECB is not set
-+CONFIG_CRYPTO_CBC=y
-+CONFIG_CRYPTO_PCBC=m
-+# CONFIG_CRYPTO_LRW is not set
-+CONFIG_CRYPTO_DES=y
-+# CONFIG_CRYPTO_FCRYPT is not set
-+# CONFIG_CRYPTO_BLOWFISH is not set
-+# CONFIG_CRYPTO_TWOFISH is not set
-+# CONFIG_CRYPTO_SERPENT is not set
-+# CONFIG_CRYPTO_AES is not set
-+# CONFIG_CRYPTO_CAST5 is not set
-+# CONFIG_CRYPTO_CAST6 is not set
-+# CONFIG_CRYPTO_TEA is not set
-+# CONFIG_CRYPTO_ARC4 is not set
-+# CONFIG_CRYPTO_KHAZAD is not set
-+# CONFIG_CRYPTO_ANUBIS is not set
-+# CONFIG_CRYPTO_DEFLATE is not set
-+# CONFIG_CRYPTO_MICHAEL_MIC is not set
-+# CONFIG_CRYPTO_CRC32C is not set
-+# CONFIG_CRYPTO_CAMELLIA is not set
-+# CONFIG_CRYPTO_TEST is not set
-
- #
- # Hardware crypto devices
-@@ -775,6 +1234,14 @@ CONFIG_DEBUG_LL=y
- #
- # Library routines
- #
-+CONFIG_BITREVERSE=y
- # CONFIG_CRC_CCITT is not set
-+# CONFIG_CRC16 is not set
- CONFIG_CRC32=y
- # CONFIG_LIBCRC32C is not set
-+CONFIG_AUDIT_GENERIC=y
-+CONFIG_ZLIB_INFLATE=y
-+CONFIG_ZLIB_DEFLATE=y
-+CONFIG_PLIST=y
-+CONFIG_HAS_IOMEM=y
-+CONFIG_HAS_IOPORT=y
-Index: linux-2.6.22.19/arch/arm/mach-at91/at91rm9200.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/at91rm9200.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/at91rm9200.c
-@@ -267,6 +267,33 @@ static void at91rm9200_reset(void)
-
-
- /* --------------------------------------------------------------------
-+ * Timer/Counter library initialization
-+ * -------------------------------------------------------------------- */
-+#ifdef CONFIG_ATMEL_TCLIB
-+
-+#include "tclib.h"
-+
-+static struct atmel_tcblock at91rm9200_tcblocks[] = {
-+ [0] = {
-+ .physaddr = AT91RM9200_BASE_TCB0,
-+ .irq = { AT91RM9200_ID_TC0, AT91RM9200_ID_TC1, AT91RM9200_ID_TC2 },
-+ .clk = { &tc0_clk, &tc1_clk, &tc2_clk },
-+ },
-+ [1] = {
-+ .physaddr = AT91RM9200_BASE_TCB1,
-+ .irq = { AT91RM9200_ID_TC3, AT91RM9200_ID_TC4, AT91RM9200_ID_TC5 },
-+ .clk = { &tc3_clk, &tc4_clk, &tc5_clk },
-+ },
-+};
-+
-+#define at91rm9200_tc_init() atmel_tc_init(at91rm9200_tcblocks, ARRAY_SIZE(at91rm9200_tcblocks))
-+
-+#else
-+#define at91rm9200_tc_init() do {} while(0)
-+#endif
-+
-+
-+/* --------------------------------------------------------------------
- * AT91RM9200 processor initialization
- * -------------------------------------------------------------------- */
- void __init at91rm9200_initialize(unsigned long main_clock, unsigned short banks)
-@@ -288,6 +315,9 @@ void __init at91rm9200_initialize(unsign
-
- /* Initialize GPIO subsystem */
- at91_gpio_init(at91rm9200_gpio, banks);
-+
-+ /* Initialize the Timer/Counter blocks */
-+ at91rm9200_tc_init();
- }
-
-
-@@ -301,28 +331,28 @@ void __init at91rm9200_initialize(unsign
- static unsigned int at91rm9200_default_irq_priority[NR_AIC_IRQS] __initdata = {
- 7, /* Advanced Interrupt Controller (FIQ) */
- 7, /* System Peripherals */
-- 0, /* Parallel IO Controller A */
-- 0, /* Parallel IO Controller B */
-- 0, /* Parallel IO Controller C */
-- 0, /* Parallel IO Controller D */
-- 6, /* USART 0 */
-- 6, /* USART 1 */
-- 6, /* USART 2 */
-- 6, /* USART 3 */
-+ 1, /* Parallel IO Controller A */
-+ 1, /* Parallel IO Controller B */
-+ 1, /* Parallel IO Controller C */
-+ 1, /* Parallel IO Controller D */
-+ 5, /* USART 0 */
-+ 5, /* USART 1 */
-+ 5, /* USART 2 */
-+ 5, /* USART 3 */
- 0, /* Multimedia Card Interface */
-- 4, /* USB Device Port */
-- 0, /* Two-Wire Interface */
-- 6, /* Serial Peripheral Interface */
-- 5, /* Serial Synchronous Controller 0 */
-- 5, /* Serial Synchronous Controller 1 */
-- 5, /* Serial Synchronous Controller 2 */
-+ 2, /* USB Device Port */
-+ 6, /* Two-Wire Interface */
-+ 5, /* Serial Peripheral Interface */
-+ 4, /* Serial Synchronous Controller 0 */
-+ 4, /* Serial Synchronous Controller 1 */
-+ 4, /* Serial Synchronous Controller 2 */
- 0, /* Timer Counter 0 */
- 0, /* Timer Counter 1 */
- 0, /* Timer Counter 2 */
- 0, /* Timer Counter 3 */
- 0, /* Timer Counter 4 */
- 0, /* Timer Counter 5 */
-- 3, /* USB Host port */
-+ 2, /* USB Host port */
- 3, /* Ethernet MAC */
- 0, /* Advanced Interrupt Controller (IRQ0) */
- 0, /* Advanced Interrupt Controller (IRQ1) */
-Index: linux-2.6.22.19/arch/arm/mach-at91/at91rm9200_devices.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/at91rm9200_devices.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/at91rm9200_devices.c
-@@ -477,7 +477,18 @@ void __init at91_add_device_i2c(void) {}
- * SPI
- * -------------------------------------------------------------------- */
-
--#if defined(CONFIG_SPI_AT91) || defined(CONFIG_SPI_AT91_MODULE) || defined(CONFIG_AT91_SPI) || defined(CONFIG_AT91_SPI_MODULE)
-+#if defined(CONFIG_AT91_SPI) || defined(CONFIG_AT91_SPI_MODULE) /* legacy SPI driver */
-+#define SPI_DEVNAME "at91_spi"
-+
-+#elif defined(CONFIG_SPI_AT91) || defined(CONFIG_SPI_AT91_MODULE) /* SPI bitbanging driver */
-+#define SPI_DEVNAME "at91_spi"
-+
-+#elif defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE) /* new SPI driver */
-+#define SPI_DEVNAME "atmel_spi"
-+
-+#endif
-+
-+#ifdef SPI_DEVNAME
- static u64 spi_dmamask = 0xffffffffUL;
-
- static struct resource spi_resources[] = {
-@@ -494,7 +505,7 @@ static struct resource spi_resources[] =
- };
-
- static struct platform_device at91rm9200_spi_device = {
-- .name = "at91_spi",
-+ .name = SPI_DEVNAME,
- .id = 0,
- .dev = {
- .dma_mask = &spi_dmamask,
-@@ -603,6 +614,32 @@ void __init at91_init_leds(u8 cpu_led, u
- #endif
-
-
-+#if defined(CONFIG_NEW_LEDS)
-+
-+static struct platform_device at91_leds = {
-+ .name = "at91_leds",
-+ .id = -1,
-+};
-+
-+void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr)
-+{
-+ if (!nr)
-+ return;
-+
-+ at91_leds.dev.platform_data = leds;
-+
-+ for ( ; nr; nr--, leds++) {
-+ leds->index = nr; /* first record stores number of leds */
-+ at91_set_gpio_output(leds->gpio, (leds->flags & 1) == 0);
-+ }
-+
-+ platform_device_register(&at91_leds);
-+}
-+#else
-+void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr) {}
-+#endif
-+
-+
- /* --------------------------------------------------------------------
- * UART
- * -------------------------------------------------------------------- */
-Index: linux-2.6.22.19/arch/arm/mach-at91/at91sam9260.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/at91sam9260.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/at91sam9260.c
-@@ -269,6 +269,33 @@ static void at91sam9260_reset(void)
-
-
- /* --------------------------------------------------------------------
-+ * Timer/Counter library initialization
-+ * -------------------------------------------------------------------- */
-+#ifdef CONFIG_ATMEL_TCLIB
-+
-+#include "tclib.h"
-+
-+static struct atmel_tcblock at91sam9260_tcblocks[] = {
-+ [0] = {
-+ .physaddr = AT91SAM9260_BASE_TCB0,
-+ .irq = { AT91SAM9260_ID_TC0, AT91SAM9260_ID_TC1, AT91SAM9260_ID_TC2 },
-+ .clk = { &tc0_clk, &tc1_clk, &tc2_clk },
-+ },
-+ [1] = {
-+ .physaddr = AT91SAM9260_BASE_TCB1,
-+ .irq = { AT91SAM9260_ID_TC3, AT91SAM9260_ID_TC4, AT91SAM9260_ID_TC5 },
-+ .clk = { &tc3_clk, &tc4_clk, &tc5_clk },
-+ },
-+};
-+
-+#define at91sam9260_tc_init() atmel_tc_init(at91sam9260_tcblocks, ARRAY_SIZE(at91sam9260_tcblocks))
-+
-+#else
-+#define at91sam9260_tc_init() do {} while(0)
-+#endif
-+
-+
-+/* --------------------------------------------------------------------
- * AT91SAM9260 processor initialization
- * -------------------------------------------------------------------- */
-
-@@ -315,6 +342,9 @@ void __init at91sam9260_initialize(unsig
-
- /* Register GPIO subsystem */
- at91_gpio_init(at91sam9260_gpio, 3);
-+
-+ /* Initialize the Timer/Counter blocks */
-+ at91sam9260_tc_init();
- }
-
- /* --------------------------------------------------------------------
-@@ -327,30 +357,30 @@ void __init at91sam9260_initialize(unsig
- static unsigned int at91sam9260_default_irq_priority[NR_AIC_IRQS] __initdata = {
- 7, /* Advanced Interrupt Controller */
- 7, /* System Peripherals */
-- 0, /* Parallel IO Controller A */
-- 0, /* Parallel IO Controller B */
-- 0, /* Parallel IO Controller C */
-+ 1, /* Parallel IO Controller A */
-+ 1, /* Parallel IO Controller B */
-+ 1, /* Parallel IO Controller C */
- 0, /* Analog-to-Digital Converter */
-- 6, /* USART 0 */
-- 6, /* USART 1 */
-- 6, /* USART 2 */
-+ 5, /* USART 0 */
-+ 5, /* USART 1 */
-+ 5, /* USART 2 */
- 0, /* Multimedia Card Interface */
-- 4, /* USB Device Port */
-- 0, /* Two-Wire Interface */
-- 6, /* Serial Peripheral Interface 0 */
-- 6, /* Serial Peripheral Interface 1 */
-+ 2, /* USB Device Port */
-+ 6, /* Two-Wire Interface */
-+ 5, /* Serial Peripheral Interface 0 */
-+ 5, /* Serial Peripheral Interface 1 */
- 5, /* Serial Synchronous Controller */
- 0,
- 0,
- 0, /* Timer Counter 0 */
- 0, /* Timer Counter 1 */
- 0, /* Timer Counter 2 */
-- 3, /* USB Host port */
-+ 2, /* USB Host port */
- 3, /* Ethernet */
- 0, /* Image Sensor Interface */
-- 6, /* USART 3 */
-- 6, /* USART 4 */
-- 6, /* USART 5 */
-+ 5, /* USART 3 */
-+ 5, /* USART 4 */
-+ 5, /* USART 5 */
- 0, /* Timer Counter 3 */
- 0, /* Timer Counter 4 */
- 0, /* Timer Counter 5 */
-Index: linux-2.6.22.19/arch/arm/mach-at91/at91sam9260_devices.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/at91sam9260_devices.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/at91sam9260_devices.c
-@@ -524,6 +524,32 @@ void __init at91_init_leds(u8 cpu_led, u
- #endif
-
-
-+#if defined(CONFIG_NEW_LEDS)
-+
-+static struct platform_device at91_leds = {
-+ .name = "at91_leds",
-+ .id = -1,
-+};
-+
-+void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr)
-+{
-+ if (!nr)
-+ return;
-+
-+ at91_leds.dev.platform_data = leds;
-+
-+ for ( ; nr; nr--, leds++) {
-+ leds->index = nr; /* first record stores number of leds */
-+ at91_set_gpio_output(leds->gpio, (leds->flags & 1) == 0);
-+ }
-+
-+ platform_device_register(&at91_leds);
-+}
-+#else
-+void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr) {}
-+#endif
-+
-+
- /* --------------------------------------------------------------------
- * UART
- * -------------------------------------------------------------------- */
-Index: linux-2.6.22.19/arch/arm/mach-at91/at91sam9261.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/at91sam9261.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/at91sam9261.c
-@@ -247,6 +247,28 @@ static void at91sam9261_reset(void)
-
-
- /* --------------------------------------------------------------------
-+ * Timer/Counter library initialization
-+ * -------------------------------------------------------------------- */
-+#ifdef CONFIG_ATMEL_TCLIB
-+
-+#include "tclib.h"
-+
-+static struct atmel_tcblock at91sam9261_tcblocks[] = {
-+ [0] = {
-+ .physaddr = AT91SAM9261_BASE_TCB0,
-+ .irq = { AT91SAM9261_ID_TC0, AT91SAM9261_ID_TC1, AT91SAM9261_ID_TC2 },
-+ .clk = { &tc0_clk, &tc1_clk, &tc2_clk },
-+ }
-+};
-+
-+#define at91sam9261_tc_init() atmel_tc_init(at91sam9261_tcblocks, ARRAY_SIZE(at91sam9261_tcblocks))
-+
-+#else
-+#define at91sam9261_tc_init() do {} while(0)
-+#endif
-+
-+
-+/* --------------------------------------------------------------------
- * AT91SAM9261 processor initialization
- * -------------------------------------------------------------------- */
-
-@@ -267,6 +289,9 @@ void __init at91sam9261_initialize(unsig
-
- /* Register GPIO subsystem */
- at91_gpio_init(at91sam9261_gpio, 3);
-+
-+ /* Initialize the Timer/Counter blocks */
-+ at91sam9261_tc_init();
- }
-
- /* --------------------------------------------------------------------
-@@ -279,25 +304,25 @@ void __init at91sam9261_initialize(unsig
- static unsigned int at91sam9261_default_irq_priority[NR_AIC_IRQS] __initdata = {
- 7, /* Advanced Interrupt Controller */
- 7, /* System Peripherals */
-- 0, /* Parallel IO Controller A */
-- 0, /* Parallel IO Controller B */
-- 0, /* Parallel IO Controller C */
-- 0,
-- 6, /* USART 0 */
-- 6, /* USART 1 */
-- 6, /* USART 2 */
-+ 1, /* Parallel IO Controller A */
-+ 1, /* Parallel IO Controller B */
-+ 1, /* Parallel IO Controller C */
-+ 0,
-+ 5, /* USART 0 */
-+ 5, /* USART 1 */
-+ 5, /* USART 2 */
- 0, /* Multimedia Card Interface */
-- 4, /* USB Device Port */
-- 0, /* Two-Wire Interface */
-- 6, /* Serial Peripheral Interface 0 */
-- 6, /* Serial Peripheral Interface 1 */
-- 5, /* Serial Synchronous Controller 0 */
-- 5, /* Serial Synchronous Controller 1 */
-- 5, /* Serial Synchronous Controller 2 */
-+ 2, /* USB Device Port */
-+ 6, /* Two-Wire Interface */
-+ 5, /* Serial Peripheral Interface 0 */
-+ 5, /* Serial Peripheral Interface 1 */
-+ 4, /* Serial Synchronous Controller 0 */
-+ 4, /* Serial Synchronous Controller 1 */
-+ 4, /* Serial Synchronous Controller 2 */
- 0, /* Timer Counter 0 */
- 0, /* Timer Counter 1 */
- 0, /* Timer Counter 2 */
-- 3, /* USB Host port */
-+ 2, /* USB Host port */
- 3, /* LCD Controller */
- 0,
- 0,
-Index: linux-2.6.22.19/arch/arm/mach-at91/at91sam9261_devices.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/at91sam9261_devices.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/at91sam9261_devices.c
-@@ -14,6 +14,9 @@
- #include <asm/mach/map.h>
-
- #include <linux/platform_device.h>
-+#include <linux/fb.h>
-+
-+#include <video/atmel_lcdc.h>
-
- #include <asm/arch/board.h>
- #include <asm/arch/gpio.h>
-@@ -522,6 +525,32 @@ void __init at91_init_leds(u8 cpu_led, u
- #endif
-
-
-+#if defined(CONFIG_NEW_LEDS)
-+
-+static struct platform_device at91_leds = {
-+ .name = "at91_leds",
-+ .id = -1,
-+};
-+
-+void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr)
-+{
-+ if (!nr)
-+ return;
-+
-+ at91_leds.dev.platform_data = leds;
-+
-+ for ( ; nr; nr--, leds++) {
-+ leds->index = nr; /* first record stores number of leds */
-+ at91_set_gpio_output(leds->gpio, (leds->flags & 1) == 0);
-+ }
-+
-+ platform_device_register(&at91_leds);
-+}
-+#else
-+void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr) {}
-+#endif
-+
-+
- /* --------------------------------------------------------------------
- * UART
- * -------------------------------------------------------------------- */
-Index: linux-2.6.22.19/arch/arm/mach-at91/at91sam9263.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/at91sam9263.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/at91sam9263.c
-@@ -273,6 +273,28 @@ static void at91sam9263_reset(void)
-
-
- /* --------------------------------------------------------------------
-+ * Timer/Counter library initialization
-+ * -------------------------------------------------------------------- */
-+#ifdef CONFIG_ATMEL_TCLIB
-+
-+#include "tclib.h"
-+
-+static struct atmel_tcblock at91sam9263_tcblocks[] = {
-+ [0] = {
-+ .physaddr = AT91SAM9263_BASE_TCB0,
-+ .irq = { AT91SAM9263_ID_TCB, AT91SAM9263_ID_TCB, AT91SAM9263_ID_TCB },
-+ .clk = { &tcb_clk, &tcb_clk, &tcb_clk },
-+ }
-+};
-+
-+#define at91sam9263_tc_init() atmel_tc_init(at91sam9263_tcblocks, ARRAY_SIZE(at91sam9263_tcblocks))
-+
-+#else
-+#define at91sam9263_tc_init() do {} while(0)
-+#endif
-+
-+
-+/* --------------------------------------------------------------------
- * AT91SAM9263 processor initialization
- * -------------------------------------------------------------------- */
-
-@@ -292,6 +314,9 @@ void __init at91sam9263_initialize(unsig
-
- /* Register GPIO subsystem */
- at91_gpio_init(at91sam9263_gpio, 5);
-+
-+ /* Initialize the Timer/Counter blocks */
-+ at91sam9263_tc_init();
- }
-
- /* --------------------------------------------------------------------
-@@ -304,34 +329,34 @@ void __init at91sam9263_initialize(unsig
- static unsigned int at91sam9263_default_irq_priority[NR_AIC_IRQS] __initdata = {
- 7, /* Advanced Interrupt Controller (FIQ) */
- 7, /* System Peripherals */
-- 0, /* Parallel IO Controller A */
-- 0, /* Parallel IO Controller B */
-- 0, /* Parallel IO Controller C, D and E */
-+ 1, /* Parallel IO Controller A */
-+ 1, /* Parallel IO Controller B */
-+ 1, /* Parallel IO Controller C, D and E */
- 0,
- 0,
-- 6, /* USART 0 */
-- 6, /* USART 1 */
-- 6, /* USART 2 */
-+ 5, /* USART 0 */
-+ 5, /* USART 1 */
-+ 5, /* USART 2 */
- 0, /* Multimedia Card Interface 0 */
- 0, /* Multimedia Card Interface 1 */
-- 4, /* CAN */
-- 0, /* Two-Wire Interface */
-- 6, /* Serial Peripheral Interface 0 */
-- 6, /* Serial Peripheral Interface 1 */
-- 5, /* Serial Synchronous Controller 0 */
-- 5, /* Serial Synchronous Controller 1 */
-- 6, /* AC97 Controller */
-+ 3, /* CAN */
-+ 6, /* Two-Wire Interface */
-+ 5, /* Serial Peripheral Interface 0 */
-+ 5, /* Serial Peripheral Interface 1 */
-+ 4, /* Serial Synchronous Controller 0 */
-+ 4, /* Serial Synchronous Controller 1 */
-+ 5, /* AC97 Controller */
- 0, /* Timer Counter 0, 1 and 2 */
- 0, /* Pulse Width Modulation Controller */
- 3, /* Ethernet */
- 0,
- 0, /* 2D Graphic Engine */
-- 3, /* USB Device Port */
-+ 2, /* USB Device Port */
- 0, /* Image Sensor Interface */
- 3, /* LDC Controller */
- 0, /* DMA Controller */
- 0,
-- 3, /* USB Host port */
-+ 2, /* USB Host port */
- 0, /* Advanced Interrupt Controller (IRQ0) */
- 0, /* Advanced Interrupt Controller (IRQ1) */
- };
-Index: linux-2.6.22.19/arch/arm/mach-at91/at91sam9263_devices.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/at91sam9263_devices.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/at91sam9263_devices.c
-@@ -13,6 +13,9 @@
- #include <asm/mach/map.h>
-
- #include <linux/platform_device.h>
-+#include <linux/fb.h>
-+
-+#include <video/atmel_lcdc.h>
-
- #include <asm/arch/board.h>
- #include <asm/arch/gpio.h>
-@@ -625,6 +628,56 @@ void __init at91_add_device_ac97(struct
-
-
- /* --------------------------------------------------------------------
-+ * Image Sensor Interface
-+ * -------------------------------------------------------------------- */
-+
-+#if defined(CONFIG_VIDEO_AT91_ISI) || defined(CONFIG_VIDEO_AT91_ISI_MODULE)
-+
-+struct resource isi_resources[] = {
-+ [0] = {
-+ .start = AT91SAM9263_BASE_ISI,
-+ .end = AT91SAM9263_BASE_ISI + SZ_16K - 1,
-+ .flags = IORESOURCE_MEM,
-+ },
-+ [1] = {
-+ .start = AT91SAM9263_ID_ISI,
-+ .end = AT91SAM9263_ID_ISI,
-+ .flags = IORESOURCE_IRQ,
-+ },
-+};
-+
-+static struct platform_device at91sam9263_isi_device = {
-+ .name = "at91_isi",
-+ .id = -1,
-+ .resource = isi_resources,
-+ .num_resources = ARRAY_SIZE(isi_resources),
-+};
-+
-+void __init at91_add_device_isi(void)
-+{
-+ at91_set_A_periph(AT91_PIN_PE0, 0); /* ISI_D0 */
-+ at91_set_A_periph(AT91_PIN_PE1, 0); /* ISI_D1 */
-+ at91_set_A_periph(AT91_PIN_PE2, 0); /* ISI_D2 */
-+ at91_set_A_periph(AT91_PIN_PE3, 0); /* ISI_D3 */
-+ at91_set_A_periph(AT91_PIN_PE4, 0); /* ISI_D4 */
-+ at91_set_A_periph(AT91_PIN_PE5, 0); /* ISI_D5 */
-+ at91_set_A_periph(AT91_PIN_PE6, 0); /* ISI_D6 */
-+ at91_set_A_periph(AT91_PIN_PE7, 0); /* ISI_D7 */
-+ at91_set_A_periph(AT91_PIN_PE8, 0); /* ISI_PCK */
-+ at91_set_A_periph(AT91_PIN_PE9, 0); /* ISI_HSYNC */
-+ at91_set_A_periph(AT91_PIN_PE10, 0); /* ISI_VSYNC */
-+ at91_set_B_periph(AT91_PIN_PE11, 0); /* ISI_MCK (PCK3) */
-+ at91_set_B_periph(AT91_PIN_PE12, 0); /* ISI_PD8 */
-+ at91_set_B_periph(AT91_PIN_PE13, 0); /* ISI_PD9 */
-+ at91_set_B_periph(AT91_PIN_PE14, 0); /* ISI_PD10 */
-+ at91_set_B_periph(AT91_PIN_PE15, 0); /* ISI_PD11 */
-+}
-+#else
-+void __init at91_add_device_isi(void) {}
-+#endif
-+
-+
-+/* --------------------------------------------------------------------
- * LCD Controller
- * -------------------------------------------------------------------- */
-
-@@ -715,6 +768,32 @@ void __init at91_init_leds(u8 cpu_led, u
- #endif
-
-
-+#if defined(CONFIG_NEW_LEDS)
-+
-+static struct platform_device at91_leds = {
-+ .name = "at91_leds",
-+ .id = -1,
-+};
-+
-+void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr)
-+{
-+ if (!nr)
-+ return;
-+
-+ at91_leds.dev.platform_data = leds;
-+
-+ for ( ; nr; nr--, leds++) {
-+ leds->index = nr; /* first record stores number of leds */
-+ at91_set_gpio_output(leds->gpio, (leds->flags & 1) == 0);
-+ }
-+
-+ platform_device_register(&at91_leds);
-+}
-+#else
-+void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr) {}
-+#endif
-+
-+
- /* --------------------------------------------------------------------
- * UART
- * -------------------------------------------------------------------- */
-Index: linux-2.6.22.19/arch/arm/mach-at91/at91sam9rl.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/at91sam9rl.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/at91sam9rl.c
-@@ -246,6 +246,28 @@ static void at91sam9rl_reset(void)
-
-
- /* --------------------------------------------------------------------
-+ * Timer/Counter library initialization
-+ * -------------------------------------------------------------------- */
-+#ifdef CONFIG_ATMEL_TCLIB
-+
-+#include "tclib.h"
-+
-+static struct atmel_tcblock at91sam9rl_tcblocks[] = {
-+ [0] = {
-+ .physaddr = AT91SAM9RL_BASE_TCB0,
-+ .irq = { AT91SAM9RL_ID_TC0, AT91SAM9RL_ID_TC1, AT91SAM9RL_ID_TC2 },
-+ .clk = { &tc0_clk, &tc1_clk, &tc2_clk },
-+ }
-+};
-+
-+#define at91sam9rl_tc_init() atmel_tc_init(at91sam9rl_tcblocks, ARRAY_SIZE(at91sam9rl_tcblocks))
-+
-+#else
-+#define at91sam9rl_tc_init() do {} while(0)
-+#endif
-+
-+
-+/* --------------------------------------------------------------------
- * AT91SAM9RL processor initialization
- * -------------------------------------------------------------------- */
-
-@@ -284,6 +306,9 @@ void __init at91sam9rl_initialize(unsign
-
- /* Register GPIO subsystem */
- at91_gpio_init(at91sam9rl_gpio, 4);
-+
-+ /* Initialize the Timer/Counter blocks */
-+ at91sam9rl_tc_init();
- }
-
- /* --------------------------------------------------------------------
-Index: linux-2.6.22.19/arch/arm/mach-at91/at91sam9rl_devices.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/at91sam9rl_devices.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/at91sam9rl_devices.c
-@@ -370,6 +370,32 @@ void __init at91_init_leds(u8 cpu_led, u
- #endif
-
-
-+#if defined(CONFIG_NEW_LEDS)
-+
-+static struct platform_device at91_leds = {
-+ .name = "at91_leds",
-+ .id = -1,
-+};
-+
-+void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr)
-+{
-+ if (!nr)
-+ return;
-+
-+ at91_leds.dev.platform_data = leds;
-+
-+ for ( ; nr; nr--, leds++) {
-+ leds->index = nr; /* first record stores number of leds */
-+ at91_set_gpio_output(leds->gpio, (leds->flags & 1) == 0);
-+ }
-+
-+ platform_device_register(&at91_leds);
-+}
-+#else
-+void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr) {}
-+#endif
-+
-+
- /* --------------------------------------------------------------------
- * UART
- * -------------------------------------------------------------------- */
-Index: linux-2.6.22.19/arch/arm/mach-at91/board-cam60.c
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/arch/arm/mach-at91/board-cam60.c
-@@ -0,0 +1,148 @@
-+/*
-+ * KwikByte CAM60
-+ *
-+ * based on board-sam9260ek.c
-+ * Copyright (C) 2005 SAN People
-+ * Copyright (C) 2006 Atmel
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+
-+#include <linux/types.h>
-+#include <linux/init.h>
-+#include <linux/mm.h>
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+#include <linux/spi/spi.h>
-+#include <linux/spi/flash.h>
-+
-+#include <asm/hardware.h>
-+#include <asm/setup.h>
-+#include <asm/mach-types.h>
-+#include <asm/irq.h>
-+
-+#include <asm/mach/arch.h>
-+#include <asm/mach/map.h>
-+#include <asm/mach/irq.h>
-+
-+#include <asm/arch/board.h>
-+#include <asm/arch/gpio.h>
-+#include <asm/arch/at91sam926x_mc.h>
-+
-+#include "generic.h"
-+
-+
-+/*
-+ * Serial port configuration.
-+ * 0 .. 5 = USART0 .. USART5
-+ * 6 = DBGU
-+ */
-+static struct at91_uart_config __initdata cam60_uart_config = {
-+ .console_tty = 0, /* ttyS0 */
-+ .nr_tty = 1,
-+ .tty_map = { 6, -1, -1, -1, -1, -1, -1 } /* ttyS0, ..., ttyS6 */
-+};
-+
-+static void __init cam60_map_io(void)
-+{
-+ /* Initialize processor: 10 MHz crystal */
-+ at91sam9260_initialize(10000000);
-+
-+ /* Setup the serial ports and console */
-+ at91_init_serial(&cam60_uart_config);
-+}
-+
-+static void __init cam60_init_irq(void)
-+{
-+ at91sam9260_init_interrupts(NULL);
-+}
-+
-+
-+/*
-+ * SPI devices.
-+ */
-+#if defined(CONFIG_MTD_DATAFLASH)
-+static struct mtd_partition __initdata cam60_spi_partitions[] = {
-+ {
-+ .name = "BOOT1",
-+ .offset = 0,
-+ .size = 4 * 1056,
-+ },
-+ {
-+ .name = "BOOT2",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = 256 * 1056,
-+ },
-+ {
-+ .name = "kernel",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = 2222 * 1056,
-+ },
-+ {
-+ .name = "file system",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = MTDPART_SIZ_FULL,
-+ },
-+};
-+
-+static struct flash_platform_data __initdata cam60_spi_flash_platform_data = {
-+ .name = "spi_flash",
-+ .parts = cam60_spi_partitions,
-+ .nr_parts = ARRAY_SIZE(cam60_spi_partitions)
-+};
-+#endif
-+
-+static struct spi_board_info cam60_spi_devices[] = {
-+#if defined(CONFIG_MTD_DATAFLASH)
-+ { /* DataFlash chip */
-+ .modalias = "mtd_dataflash",
-+ .chip_select = 0,
-+ .max_speed_hz = 15 * 1000 * 1000,
-+ .bus_num = 0,
-+ .platform_data = &cam60_spi_flash_platform_data
-+ },
-+#endif
-+};
-+
-+
-+/*
-+ * MACB Ethernet device
-+ */
-+static struct __initdata at91_eth_data cam60_macb_data = {
-+ .phy_irq_pin = AT91_PIN_PB5,
-+ .is_rmii = 0,
-+};
-+
-+
-+static void __init cam60_board_init(void)
-+{
-+ /* Serial */
-+ at91_add_device_serial();
-+ /* SPI */
-+ at91_add_device_spi(cam60_spi_devices, ARRAY_SIZE(cam60_spi_devices));
-+ /* Ethernet */
-+ at91_add_device_eth(&cam60_macb_data);
-+}
-+
-+MACHINE_START(CAM60, "KwikByte CAM60")
-+ /* Maintainer: KwikByte */
-+ .phys_io = AT91_BASE_SYS,
-+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
-+ .boot_params = AT91_SDRAM_BASE + 0x100,
-+ .timer = &at91sam926x_timer,
-+ .map_io = cam60_map_io,
-+ .init_irq = cam60_init_irq,
-+ .init_machine = cam60_board_init,
-+MACHINE_END
-Index: linux-2.6.22.19/arch/arm/mach-at91/board-chub.c
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/arch/arm/mach-at91/board-chub.c
-@@ -0,0 +1,132 @@
-+/*
-+ * linux/arch/arm/mach-at91/board-chub.c
-+ *
-+ * Copyright (C) 2005 SAN People, adapted for Promwad Chub board
-+ * by Kuten Ivan
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+
-+#include <linux/types.h>
-+#include <linux/init.h>
-+#include <linux/mm.h>
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <asm/hardware.h>
-+#include <asm/setup.h>
-+#include <asm/mach-types.h>
-+#include <asm/irq.h>
-+
-+#include <asm/mach/arch.h>
-+#include <asm/mach/map.h>
-+#include <asm/mach/irq.h>
-+
-+#include <asm/arch/board.h>
-+#include <asm/arch/gpio.h>
-+
-+#include "generic.h"
-+
-+/*
-+ * Serial port configuration.
-+ * 0 .. 3 = USART0 .. USART3
-+ * 4 = DBGU
-+ */
-+static struct at91_uart_config __initdata chub_uart_config = {
-+ .console_tty = 0, /* ttyS0 */
-+ .nr_tty = 5,
-+ .tty_map = { 4, 0, 1, 2, 3 } /* ttyS0, ..., ttyS4 */
-+};
-+
-+static void __init chub_init_irq(void)
-+{
-+ at91rm9200_init_interrupts(NULL);
-+}
-+
-+static void __init chub_map_io(void)
-+{
-+ /* Initialize clocks: 18.432 MHz crystal */
-+ at91rm9200_initialize(18432000, AT91RM9200_PQFP);
-+
-+ /* Setup the serial ports and console */
-+ at91_init_serial(&chub_uart_config);
-+}
-+
-+static struct at91_eth_data __initdata chub_eth_data = {
-+ .phy_irq_pin = AT91_PIN_PB29,
-+ .is_rmii = 0,
-+};
-+
-+static struct mtd_partition __initdata chub_nand_partition[] = {
-+ {
-+ .name = "NAND Partition 1",
-+ .offset = 0,
-+ .size = MTDPART_SIZ_FULL,
-+ },
-+};
-+
-+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
-+{
-+ *num_partitions = ARRAY_SIZE(chub_nand_partition);
-+ return chub_nand_partition;
-+}
-+
-+static struct at91_nand_data __initdata chub_nand_data = {
-+ .ale = 22,
-+ .cle = 21,
-+ .enable_pin = AT91_PIN_PA27,
-+ .partition_info = nand_partitions,
-+};
-+
-+static struct spi_board_info chub_spi_devices[] = {
-+ { /* DataFlash chip */
-+ .modalias = "mtd_dataflash",
-+ .chip_select = 0,
-+ .max_speed_hz = 15 * 1000 * 1000,
-+ },
-+};
-+
-+static void __init chub_board_init(void)
-+{
-+ /* Serial */
-+ at91_add_device_serial();
-+ /* I2C */
-+ at91_add_device_i2c();
-+ /* Ethernet */
-+ at91_add_device_eth(&chub_eth_data);
-+ /* SPI */
-+ at91_add_device_spi(chub_spi_devices, ARRAY_SIZE(chub_spi_devices));
-+ /* NAND Flash */
-+ at91_add_device_nand(&chub_nand_data);
-+ /* Disable write protect for NAND */
-+ at91_set_gpio_output(AT91_PIN_PB7, 1);
-+ /* Power enable for 3x RS-232 and 1x RS-485 */
-+ at91_set_gpio_output(AT91_PIN_PB9, 1);
-+ /* Disable write protect for FRAM */
-+ at91_set_gpio_output(AT91_PIN_PA21, 1);
-+ /* Disable write protect for Dataflash */
-+ at91_set_gpio_output(AT91_PIN_PA19, 1);
-+}
-+
-+MACHINE_START(CHUB, "Promwad Chub")
-+ /* Maintainer: Ivan Kuten AT Promwad DOT com */
-+ .phys_io = AT91_BASE_SYS,
-+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
-+ .boot_params = AT91_SDRAM_BASE + 0x100,
-+ .timer = &at91rm9200_timer,
-+ .map_io = chub_map_io,
-+ .init_irq = chub_init_irq,
-+ .init_machine = chub_board_init,
-+MACHINE_END
-Index: linux-2.6.22.19/arch/arm/mach-at91/board-csb337.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/board-csb337.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/board-csb337.c
-@@ -24,6 +24,7 @@
- #include <linux/module.h>
- #include <linux/platform_device.h>
- #include <linux/spi/spi.h>
-+#include <linux/interrupt.h>
- #include <linux/mtd/physmap.h>
-
- #include <asm/hardware.h>
-@@ -59,6 +60,7 @@ static void __init csb337_map_io(void)
-
- /* Setup the LEDs */
- at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
-+ at91_set_gpio_output(AT91_PIN_PB2, 1); /* third (unused) LED */
-
- /* Setup the serial ports and console */
- at91_init_serial(&csb337_uart_config);
-@@ -149,6 +151,55 @@ static struct platform_device csb_flash
- .num_resources = ARRAY_SIZE(csb_flash_resources),
- };
-
-+static struct at91_gpio_led csb337_leds[] = {
-+ {
-+ .name = "led0",
-+ .gpio = AT91_PIN_PB0,
-+ .trigger = "heartbeat",
-+ },
-+ {
-+ .name = "led1",
-+ .gpio = AT91_PIN_PB1,
-+ .trigger = "timer",
-+ },
-+ {
-+ .name = "led2",
-+ .gpio = AT91_PIN_PB2,
-+ }
-+};
-+
-+#if defined(CONFIG_CSB300_WAKE_SW0) || defined(CONFIG_CSB300_WAKE_SW1)
-+static irqreturn_t switch_irq_handler(int irq, void *context)
-+{
-+ return IRQ_HANDLED;
-+}
-+
-+static inline void __init switch_irq_setup(int irq, char *name, unsigned long mode)
-+{
-+ int res;
-+
-+ res = request_irq(irq, switch_irq_handler, IRQF_SAMPLE_RANDOM | mode, name, NULL);
-+ if (res == 0)
-+ enable_irq_wake(irq);
-+}
-+
-+static void __init csb300_switches(void)
-+{
-+#ifdef CONFIG_CSB300_WAKE_SW0
-+ at91_set_A_periph(AT91_PIN_PB29, 1); /* IRQ0 */
-+ switch_irq_setup(AT91RM9200_ID_IRQ0, "csb300_sw0", IRQF_TRIGGER_FALLING);
-+#endif
-+#ifdef CONFIG_CSB300_WAKE_SW1
-+ at91_set_gpio_input(AT91_PIN_PB28, 1);
-+ at91_set_deglitch(AT91_PIN_PB28, 1);
-+ switch_irq_setup(AT91_PIN_PB28, "csb300_sw1", IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING);
-+#endif
-+ /* there's also SW2 at PA21, GPIO or TIOA2 */
-+}
-+#else
-+static void __init csb300_switches(void) {}
-+#endif
-+
- static void __init csb337_board_init(void)
- {
- /* Serial */
-@@ -168,8 +219,12 @@ static void __init csb337_board_init(voi
- at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices));
- /* MMC */
- at91_add_device_mmc(0, &csb337_mmc_data);
-+ /* LEDS */
-+ at91_gpio_leds(csb337_leds, ARRAY_SIZE(csb337_leds));
- /* NOR flash */
- platform_device_register(&csb_flash);
-+ /* Switches on CSB300 */
-+ csb300_switches();
- }
-
- MACHINE_START(CSB337, "Cogent CSB337")
-Index: linux-2.6.22.19/arch/arm/mach-at91/board-dk.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/board-dk.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/board-dk.c
-@@ -73,6 +73,185 @@ static void __init dk_init_irq(void)
- at91rm9200_init_interrupts(NULL);
- }
-
-+#if defined(CONFIG_FB_S1D13XXX) || defined(CONFIG_FB_S1D13XXX_MODULE)
-+#include <video/s1d13xxxfb.h>
-+#include <asm/arch/ics1523.h>
-+
-+/* EPSON S1D13806 FB */
-+#define AT91_FB_REG_BASE 0x30000000L
-+#define AT91_FB_REG_SIZE 0x200
-+#define AT91_FB_VMEM_BASE 0x30200000L
-+#define AT91_FB_VMEM_SIZE 0x140000L
-+
-+static void __init dk_init_video(void)
-+{
-+ /* NWAIT Signal */
-+ at91_set_A_periph(AT91_PIN_PC6, 0);
-+
-+ /* Initialization of the Static Memory Controller for Chip Select 2 */
-+ at91_sys_write(AT91_SMC_CSR(2), AT91_SMC_DBW_16 /* 16 bit */
-+ | AT91_SMC_WSEN | AT91_SMC_NWS_(4) /* wait states */
-+ | AT91_SMC_TDF_(1) /* float time */
-+ );
-+
-+ at91_ics1523_init();
-+}
-+
-+/* CRT: (active) 640x480 60Hz (PCLK=CLKI=25.175MHz)
-+ Memory: Embedded SDRAM (MCLK=CLKI3=50.000MHz) (BUSCLK=60.000MHz) */
-+static const struct s1d13xxxfb_regval dk_s1dfb_initregs[] = {
-+ {S1DREG_MISC, 0x00}, /* Enable Memory/Register select bit */
-+ {S1DREG_COM_DISP_MODE, 0x00}, /* disable display output */
-+ {S1DREG_GPIO_CNF0, 0x00},
-+ {S1DREG_GPIO_CNF1, 0x00},
-+ {S1DREG_GPIO_CTL0, 0x08},
-+ {S1DREG_GPIO_CTL1, 0x00},
-+ {S1DREG_CLK_CNF, 0x01}, /* no divide, MCLK source is CLKI3 0x02*/
-+ {S1DREG_LCD_CLK_CNF, 0x00},
-+ {S1DREG_CRT_CLK_CNF, 0x00},
-+ {S1DREG_MPLUG_CLK_CNF, 0x00},
-+ {S1DREG_CPU2MEM_WST_SEL, 0x01}, /* 2*period(MCLK) - 4ns > period(BCLK) */
-+ {S1DREG_SDRAM_REF_RATE, 0x03}, /* 32768 <= MCLK <= 50000 (MHz) */
-+ {S1DREG_SDRAM_TC0, 0x00}, /* MCLK source freq (MHz): */
-+ {S1DREG_SDRAM_TC1, 0x01}, /* 42 <= MCLK <= 50 */
-+ {S1DREG_MEM_CNF, 0x80}, /* SDRAM Initialization - needed before mem access */
-+ {S1DREG_PANEL_TYPE, 0x25}, /* std TFT 16bit, 8bit SCP format 2, single passive LCD */
-+ {S1DREG_MOD_RATE, 0x00}, /* toggle every FPFRAME */
-+ {S1DREG_LCD_DISP_HWIDTH, 0x4F}, /* 680 pix */
-+ {S1DREG_LCD_NDISP_HPER, 0x12}, /* 152 pix */
-+ {S1DREG_TFT_FPLINE_START, 0x01}, /* 13 pix */
-+ {S1DREG_TFT_FPLINE_PWIDTH, 0x0B}, /* 96 pix */
-+ {S1DREG_LCD_DISP_VHEIGHT0, 0xDF},
-+ {S1DREG_LCD_DISP_VHEIGHT1, 0x01}, /* 480 lines */
-+ {S1DREG_LCD_NDISP_VPER, 0x2C}, /* 44 lines */
-+ {S1DREG_TFT_FPFRAME_START, 0x0A}, /* 10 lines */
-+ {S1DREG_TFT_FPFRAME_PWIDTH, 0x01}, /* 2 lines */
-+ {S1DREG_LCD_DISP_MODE, 0x05}, /* 16 bpp */
-+ {S1DREG_LCD_MISC, 0x00}, /* dithering enabled, dual panel buffer enabled */
-+ {S1DREG_LCD_DISP_START0, 0x00},
-+ {S1DREG_LCD_DISP_START1, 0xC8},
-+ {S1DREG_LCD_DISP_START2, 0x00},
-+ {S1DREG_LCD_MEM_OFF0, 0x80},
-+ {S1DREG_LCD_MEM_OFF1, 0x02},
-+ {S1DREG_LCD_PIX_PAN, 0x00},
-+ {S1DREG_LCD_DISP_FIFO_HTC, 0x3B},
-+ {S1DREG_LCD_DISP_FIFO_LTC, 0x3C},
-+ {S1DREG_CRT_DISP_HWIDTH, 0x4F}, /* 680 pix */
-+ {S1DREG_CRT_NDISP_HPER, 0x13}, /* 160 pix */
-+ {S1DREG_CRT_HRTC_START, 0x01}, /* 13 pix */
-+ {S1DREG_CRT_HRTC_PWIDTH, 0x0B}, /* 96 pix */
-+ {S1DREG_CRT_DISP_VHEIGHT0, 0xDF},
-+ {S1DREG_CRT_DISP_VHEIGHT1, 0x01}, /* 480 lines */
-+ {S1DREG_CRT_NDISP_VPER, 0x2B}, /* 44 lines */
-+ {S1DREG_CRT_VRTC_START, 0x09}, /* 10 lines */
-+ {S1DREG_CRT_VRTC_PWIDTH, 0x01}, /* 2 lines */
-+ {S1DREG_TV_OUT_CTL, 0x10},
-+ {S1DREG_CRT_DISP_MODE, 0x05}, /* 16 bpp */
-+ {S1DREG_CRT_DISP_START0, 0x00},
-+ {S1DREG_CRT_DISP_START1, 0x00},
-+ {S1DREG_CRT_DISP_START2, 0x00},
-+ {S1DREG_CRT_MEM_OFF0, 0x80},
-+ {S1DREG_CRT_MEM_OFF1, 0x02},
-+ {S1DREG_CRT_PIX_PAN, 0x00},
-+ {S1DREG_CRT_DISP_FIFO_HTC, 0x3B},
-+ {S1DREG_CRT_DISP_FIFO_LTC, 0x3C},
-+ {S1DREG_LCD_CUR_CTL, 0x00}, /* inactive */
-+ {S1DREG_LCD_CUR_START, 0x01},
-+ {S1DREG_LCD_CUR_XPOS0, 0x00},
-+ {S1DREG_LCD_CUR_XPOS1, 0x00},
-+ {S1DREG_LCD_CUR_YPOS0, 0x00},
-+ {S1DREG_LCD_CUR_YPOS1, 0x00},
-+ {S1DREG_LCD_CUR_BCTL0, 0x00},
-+ {S1DREG_LCD_CUR_GCTL0, 0x00},
-+ {S1DREG_LCD_CUR_RCTL0, 0x00},
-+ {S1DREG_LCD_CUR_BCTL1, 0x1F},
-+ {S1DREG_LCD_CUR_GCTL1, 0x3F},
-+ {S1DREG_LCD_CUR_RCTL1, 0x1F},
-+ {S1DREG_LCD_CUR_FIFO_HTC, 0x00},
-+ {S1DREG_CRT_CUR_CTL, 0x00}, /* inactive */
-+ {S1DREG_CRT_CUR_START, 0x01},
-+ {S1DREG_CRT_CUR_XPOS0, 0x00},
-+ {S1DREG_CRT_CUR_XPOS1, 0x00},
-+ {S1DREG_CRT_CUR_YPOS0, 0x00},
-+ {S1DREG_CRT_CUR_YPOS1, 0x00},
-+ {S1DREG_CRT_CUR_BCTL0, 0x00},
-+ {S1DREG_CRT_CUR_GCTL0, 0x00},
-+ {S1DREG_CRT_CUR_RCTL0, 0x00},
-+ {S1DREG_CRT_CUR_BCTL1, 0x1F},
-+ {S1DREG_CRT_CUR_GCTL1, 0x3F},
-+ {S1DREG_CRT_CUR_RCTL1, 0x1F},
-+ {S1DREG_CRT_CUR_FIFO_HTC, 0x00},
-+ {S1DREG_BBLT_CTL0, 0x00},
-+ {S1DREG_BBLT_CTL0, 0x00},
-+ {S1DREG_BBLT_CC_EXP, 0x00},
-+ {S1DREG_BBLT_OP, 0x00},
-+ {S1DREG_BBLT_SRC_START0, 0x00},
-+ {S1DREG_BBLT_SRC_START1, 0x00},
-+ {S1DREG_BBLT_SRC_START2, 0x00},
-+ {S1DREG_BBLT_DST_START0, 0x00},
-+ {S1DREG_BBLT_DST_START1, 0x00},
-+ {S1DREG_BBLT_DST_START2, 0x00},
-+ {S1DREG_BBLT_MEM_OFF0, 0x00},
-+ {S1DREG_BBLT_MEM_OFF1, 0x00},
-+ {S1DREG_BBLT_WIDTH0, 0x00},
-+ {S1DREG_BBLT_WIDTH1, 0x00},
-+ {S1DREG_BBLT_HEIGHT0, 0x00},
-+ {S1DREG_BBLT_HEIGHT1, 0x00},
-+ {S1DREG_BBLT_BGC0, 0x00},
-+ {S1DREG_BBLT_BGC1, 0x00},
-+ {S1DREG_BBLT_FGC0, 0x00},
-+ {S1DREG_BBLT_FGC1, 0x00},
-+ {S1DREG_LKUP_MODE, 0x00}, /* LCD LUT r | LCD and CRT/TV LUT w */
-+ {S1DREG_LKUP_ADDR, 0x00},
-+ {S1DREG_PS_CNF, 0x00}, /* Power Save disable */
-+ {S1DREG_PS_STATUS, 0x02}, /* LCD Panel down, mem up */
-+ {S1DREG_CPU2MEM_WDOGT, 0x00},
-+ {S1DREG_COM_DISP_MODE, 0x02}, /* enable CRT display output */
-+};
-+
-+static struct s1d13xxxfb_pdata dk_s1dfb_pdata = {
-+ .initregs = dk_s1dfb_initregs,
-+ .initregssize = ARRAY_SIZE(dk_s1dfb_initregs),
-+ .platform_init_video = dk_init_video,
-+};
-+
-+static u64 s1dfb_dmamask = 0xffffffffUL;
-+
-+static struct resource dk_s1dfb_resource[] = {
-+ [0] = { /* video mem */
-+ .name = "s1d13806 memory",
-+ .start = AT91_FB_VMEM_BASE,
-+ .end = AT91_FB_VMEM_BASE + AT91_FB_VMEM_SIZE -1,
-+ .flags = IORESOURCE_MEM,
-+ },
-+ [1] = { /* video registers */
-+ .name = "s1d13806 registers",
-+ .start = AT91_FB_REG_BASE,
-+ .end = AT91_FB_REG_BASE + AT91_FB_REG_SIZE -1,
-+ .flags = IORESOURCE_MEM,
-+ },
-+};
-+
-+static struct platform_device dk_s1dfb_device = {
-+ .name = "s1d13806fb",
-+ .id = -1,
-+ .dev = {
-+ .dma_mask = &s1dfb_dmamask,
-+ .coherent_dma_mask = 0xffffffff,
-+ .platform_data = &dk_s1dfb_pdata,
-+ },
-+ .resource = dk_s1dfb_resource,
-+ .num_resources = ARRAY_SIZE(dk_s1dfb_resource),
-+};
-+
-+static void __init dk_add_device_video(void)
-+{
-+ platform_device_register(&dk_s1dfb_device);
-+}
-+#else
-+static void __init dk_add_device_video(void) {}
-+#endif
-+
- static struct at91_eth_data __initdata dk_eth_data = {
- .phy_irq_pin = AT91_PIN_PC4,
- .is_rmii = 1,
-@@ -151,7 +330,7 @@ static struct at91_nand_data __initdata
- #define DK_FLASH_SIZE 0x200000
-
- static struct physmap_flash_data dk_flash_data = {
-- .width = 2,
-+ .width = 2,
- };
-
- static struct resource dk_flash_resource = {
-@@ -170,6 +349,13 @@ static struct platform_device dk_flash =
- .num_resources = 1,
- };
-
-+static struct at91_gpio_led dk_leds[] = {
-+ {
-+ .name = "led0",
-+ .gpio = AT91_PIN_PB2,
-+ .trigger = "timer",
-+ }
-+};
-
- static void __init dk_board_init(void)
- {
-@@ -200,8 +386,10 @@ static void __init dk_board_init(void)
- at91_add_device_nand(&dk_nand_data);
- /* NOR Flash */
- platform_device_register(&dk_flash);
-+ /* LEDs */
-+ at91_gpio_leds(dk_leds, ARRAY_SIZE(dk_leds));
- /* VGA */
--// dk_add_device_video();
-+ dk_add_device_video();
- }
-
- MACHINE_START(AT91RM9200DK, "Atmel AT91RM9200-DK")
-Index: linux-2.6.22.19/arch/arm/mach-at91/board-ek.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/board-ek.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/board-ek.c
-@@ -73,6 +73,187 @@ static void __init ek_init_irq(void)
- at91rm9200_init_interrupts(NULL);
- }
-
-+#if defined(CONFIG_FB_S1D13XXX) || defined(CONFIG_FB_S1D13XXX_MODULE)
-+#include <video/s1d13xxxfb.h>
-+#include <asm/arch/ics1523.h>
-+
-+/* EPSON S1D13806 FB */
-+#define AT91_FB_REG_BASE 0x40000000L
-+#define AT91_FB_REG_SIZE 0x200
-+#define AT91_FB_VMEM_BASE 0x40200000L
-+#define AT91_FB_VMEM_SIZE 0x140000L
-+
-+static void __init ek_init_video(void)
-+{
-+ /* NWAIT Signal */
-+ at91_set_A_periph(AT91_PIN_PC6, 0);
-+
-+ /* Initialization of the Static Memory Controller for Chip Select 3 */
-+ at91_sys_write(AT91_SMC_CSR(3), AT91_SMC_DBW_16 /* 16 bit */
-+ | AT91_SMC_WSEN | AT91_SMC_NWS_(5) /* wait states */
-+ | AT91_SMC_TDF_(1) /* float time */
-+ );
-+
-+ at91_ics1523_init();
-+}
-+
-+/* CRT: (active) 640x480 60Hz (PCLK=CLKI=25.175MHz)
-+ Memory: Embedded SDRAM (MCLK=CLKI3=50.000MHz) (BUSCLK=60.000MHz) */
-+static const struct s1d13xxxfb_regval ek_s1dfb_initregs[] = {
-+ {S1DREG_MISC, 0x00}, /* Enable Memory/Register select bit */
-+ {S1DREG_COM_DISP_MODE, 0x00}, /* disable display output */
-+ {S1DREG_GPIO_CNF0, 0xFF}, // 0x00
-+ {S1DREG_GPIO_CNF1, 0x1F}, // 0x08
-+ {S1DREG_GPIO_CTL0, 0x00},
-+ {S1DREG_GPIO_CTL1, 0x00},
-+ {S1DREG_CLK_CNF, 0x01}, /* no divide, MCLK source is CLKI3 0x02*/
-+ {S1DREG_LCD_CLK_CNF, 0x00},
-+ {S1DREG_CRT_CLK_CNF, 0x00},
-+ {S1DREG_MPLUG_CLK_CNF, 0x00},
-+ {S1DREG_CPU2MEM_WST_SEL, 0x01}, /* 2*period(MCLK) - 4ns > period(BCLK) */
-+ {S1DREG_SDRAM_REF_RATE, 0x03}, /* 32768 <= MCLK <= 50000 (MHz) */
-+ {S1DREG_SDRAM_TC0, 0x00}, /* MCLK source freq (MHz): */
-+ {S1DREG_SDRAM_TC1, 0x01}, /* 42 <= MCLK <= 50 */
-+ {S1DREG_MEM_CNF, 0x80}, /* SDRAM Initialization - needed before mem access */
-+ {S1DREG_PANEL_TYPE, 0x25}, /* std TFT 16bit, 8bit SCP format 2, single passive LCD */
-+ {S1DREG_MOD_RATE, 0x00}, /* toggle every FPFRAME */
-+ {S1DREG_LCD_DISP_HWIDTH, 0x4F}, /* 680 pix */
-+ {S1DREG_LCD_NDISP_HPER, 0x12}, /* 152 pix */
-+ {S1DREG_TFT_FPLINE_START, 0x01}, /* 13 pix */
-+ {S1DREG_TFT_FPLINE_PWIDTH, 0x0B}, /* 96 pix */
-+ {S1DREG_LCD_DISP_VHEIGHT0, 0xDF},
-+ {S1DREG_LCD_DISP_VHEIGHT1, 0x01}, /* 480 lines */
-+ {S1DREG_LCD_NDISP_VPER, 0x2C}, /* 44 lines */
-+ {S1DREG_TFT_FPFRAME_START, 0x0A}, /* 10 lines */
-+ {S1DREG_TFT_FPFRAME_PWIDTH, 0x01}, /* 2 lines */
-+ {S1DREG_LCD_DISP_MODE, 0x05}, /* 16 bpp */
-+ {S1DREG_LCD_MISC, 0x00}, /* dithering enabled, dual panel buffer enabled */
-+ {S1DREG_LCD_DISP_START0, 0x00},
-+ {S1DREG_LCD_DISP_START1, 0xC8},
-+ {S1DREG_LCD_DISP_START2, 0x00},
-+ {S1DREG_LCD_MEM_OFF0, 0x80},
-+ {S1DREG_LCD_MEM_OFF1, 0x02},
-+ {S1DREG_LCD_PIX_PAN, 0x00},
-+ {S1DREG_LCD_DISP_FIFO_HTC, 0x3B},
-+ {S1DREG_LCD_DISP_FIFO_LTC, 0x3C},
-+ {S1DREG_CRT_DISP_HWIDTH, 0x4F}, /* 680 pix */
-+ {S1DREG_CRT_NDISP_HPER, 0x13}, /* 160 pix */
-+ {S1DREG_CRT_HRTC_START, 0x01}, /* 13 pix */
-+ {S1DREG_CRT_HRTC_PWIDTH, 0x0B}, /* 96 pix */
-+ {S1DREG_CRT_DISP_VHEIGHT0, 0xDF},
-+ {S1DREG_CRT_DISP_VHEIGHT1, 0x01}, /* 480 lines */
-+ {S1DREG_CRT_NDISP_VPER, 0x2B}, /* 44 lines */
-+ {S1DREG_CRT_VRTC_START, 0x09}, /* 10 lines */
-+ {S1DREG_CRT_VRTC_PWIDTH, 0x01}, /* 2 lines */
-+ {S1DREG_TV_OUT_CTL, 0x10},
-+ {0x005E, 0x9F},
-+ {0x005F, 0x00},
-+ {S1DREG_CRT_DISP_MODE, 0x05}, /* 16 bpp */
-+ {S1DREG_CRT_DISP_START0, 0x00},
-+ {S1DREG_CRT_DISP_START1, 0x00},
-+ {S1DREG_CRT_DISP_START2, 0x00},
-+ {S1DREG_CRT_MEM_OFF0, 0x80},
-+ {S1DREG_CRT_MEM_OFF1, 0x02},
-+ {S1DREG_CRT_PIX_PAN, 0x00},
-+ {S1DREG_CRT_DISP_FIFO_HTC, 0x3B},
-+ {S1DREG_CRT_DISP_FIFO_LTC, 0x3C},
-+ {S1DREG_LCD_CUR_CTL, 0x00}, /* inactive */
-+ {S1DREG_LCD_CUR_START, 0x01},
-+ {S1DREG_LCD_CUR_XPOS0, 0x00},
-+ {S1DREG_LCD_CUR_XPOS1, 0x00},
-+ {S1DREG_LCD_CUR_YPOS0, 0x00},
-+ {S1DREG_LCD_CUR_YPOS1, 0x00},
-+ {S1DREG_LCD_CUR_BCTL0, 0x00},
-+ {S1DREG_LCD_CUR_GCTL0, 0x00},
-+ {S1DREG_LCD_CUR_RCTL0, 0x00},
-+ {S1DREG_LCD_CUR_BCTL1, 0x1F},
-+ {S1DREG_LCD_CUR_GCTL1, 0x3F},
-+ {S1DREG_LCD_CUR_RCTL1, 0x1F},
-+ {S1DREG_LCD_CUR_FIFO_HTC, 0x00},
-+ {S1DREG_CRT_CUR_CTL, 0x00}, /* inactive */
-+ {S1DREG_CRT_CUR_START, 0x01},
-+ {S1DREG_CRT_CUR_XPOS0, 0x00},
-+ {S1DREG_CRT_CUR_XPOS1, 0x00},
-+ {S1DREG_CRT_CUR_YPOS0, 0x00},
-+ {S1DREG_CRT_CUR_YPOS1, 0x00},
-+ {S1DREG_CRT_CUR_BCTL0, 0x00},
-+ {S1DREG_CRT_CUR_GCTL0, 0x00},
-+ {S1DREG_CRT_CUR_RCTL0, 0x00},
-+ {S1DREG_CRT_CUR_BCTL1, 0x1F},
-+ {S1DREG_CRT_CUR_GCTL1, 0x3F},
-+ {S1DREG_CRT_CUR_RCTL1, 0x1F},
-+ {S1DREG_CRT_CUR_FIFO_HTC, 0x00},
-+ {S1DREG_BBLT_CTL0, 0x00},
-+ {S1DREG_BBLT_CTL0, 0x00},
-+ {S1DREG_BBLT_CC_EXP, 0x00},
-+ {S1DREG_BBLT_OP, 0x00},
-+ {S1DREG_BBLT_SRC_START0, 0x00},
-+ {S1DREG_BBLT_SRC_START1, 0x00},
-+ {S1DREG_BBLT_SRC_START2, 0x00},
-+ {S1DREG_BBLT_DST_START0, 0x00},
-+ {S1DREG_BBLT_DST_START1, 0x00},
-+ {S1DREG_BBLT_DST_START2, 0x00},
-+ {S1DREG_BBLT_MEM_OFF0, 0x00},
-+ {S1DREG_BBLT_MEM_OFF1, 0x00},
-+ {S1DREG_BBLT_WIDTH0, 0x00},
-+ {S1DREG_BBLT_WIDTH1, 0x00},
-+ {S1DREG_BBLT_HEIGHT0, 0x00},
-+ {S1DREG_BBLT_HEIGHT1, 0x00},
-+ {S1DREG_BBLT_BGC0, 0x00},
-+ {S1DREG_BBLT_BGC1, 0x00},
-+ {S1DREG_BBLT_FGC0, 0x00},
-+ {S1DREG_BBLT_FGC1, 0x00},
-+ {S1DREG_LKUP_MODE, 0x00}, /* LCD LUT r | LCD and CRT/TV LUT w */
-+ {S1DREG_LKUP_ADDR, 0x00},
-+ {S1DREG_PS_CNF, 0x10}, /* Power Save disable */
-+ {S1DREG_PS_STATUS, 0x02}, /* LCD Panel down, mem up */
-+ {S1DREG_CPU2MEM_WDOGT, 0x00},
-+ {S1DREG_COM_DISP_MODE, 0x02}, /* enable CRT display output */
-+};
-+
-+static struct s1d13xxxfb_pdata ek_s1dfb_pdata = {
-+ .initregs = ek_s1dfb_initregs,
-+ .initregssize = ARRAY_SIZE(ek_s1dfb_initregs),
-+ .platform_init_video = ek_init_video,
-+};
-+
-+static u64 s1dfb_dmamask = 0xffffffffUL;
-+
-+static struct resource ek_s1dfb_resource[] = {
-+ [0] = { /* video mem */
-+ .name = "s1d13806 memory",
-+ .start = AT91_FB_VMEM_BASE,
-+ .end = AT91_FB_VMEM_BASE + AT91_FB_VMEM_SIZE -1,
-+ .flags = IORESOURCE_MEM,
-+ },
-+ [1] = { /* video registers */
-+ .name = "s1d13806 registers",
-+ .start = AT91_FB_REG_BASE,
-+ .end = AT91_FB_REG_BASE + AT91_FB_REG_SIZE -1,
-+ .flags = IORESOURCE_MEM,
-+ },
-+};
-+
-+static struct platform_device ek_s1dfb_device = {
-+ .name = "s1d13806fb",
-+ .id = -1,
-+ .dev = {
-+ .dma_mask = &s1dfb_dmamask,
-+ .coherent_dma_mask = 0xffffffff,
-+ .platform_data = &ek_s1dfb_pdata,
-+ },
-+ .resource = ek_s1dfb_resource,
-+ .num_resources = ARRAY_SIZE(ek_s1dfb_resource),
-+};
-+
-+static void __init ek_add_device_video(void)
-+{
-+ platform_device_register(&ek_s1dfb_device);
-+}
-+#else
-+static void __init ek_add_device_video(void) {}
-+#endif
-+
- static struct at91_eth_data __initdata ek_eth_data = {
- .phy_irq_pin = AT91_PIN_PC4,
- .is_rmii = 1,
-@@ -113,7 +294,7 @@ static struct spi_board_info ek_spi_devi
- #define EK_FLASH_SIZE 0x200000
-
- static struct physmap_flash_data ek_flash_data = {
-- .width = 2,
-+ .width = 2,
- };
-
- static struct resource ek_flash_resource = {
-@@ -132,6 +313,18 @@ static struct platform_device ek_flash =
- .num_resources = 1,
- };
-
-+static struct at91_gpio_led ek_leds[] = {
-+ {
-+ .name = "led0",
-+ .gpio = AT91_PIN_PB1,
-+ .trigger = "heartbeat",
-+ },
-+ {
-+ .name = "led1",
-+ .gpio = AT91_PIN_PB2,
-+ .trigger = "timer",
-+ }
-+};
-
- static void __init ek_board_init(void)
- {
-@@ -158,8 +351,10 @@ static void __init ek_board_init(void)
- #endif
- /* NOR Flash */
- platform_device_register(&ek_flash);
-+ /* LEDs */
-+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
- /* VGA */
--// ek_add_device_video();
-+ ek_add_device_video();
- }
-
- MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK")
-Index: linux-2.6.22.19/arch/arm/mach-at91/board-kb9202.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/board-kb9202.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/board-kb9202.c
-@@ -37,6 +37,8 @@
- #include <asm/arch/board.h>
- #include <asm/arch/gpio.h>
-
-+#include <asm/arch/at91rm9200_mc.h>
-+
- #include "generic.h"
-
-
-@@ -111,6 +113,48 @@ static struct at91_nand_data __initdata
- .partition_info = nand_partitions,
- };
-
-+
-+#if defined(CONFIG_FB_S1D15605)
-+#warning "Rather pass reset pin via platform_data"
-+static struct resource kb9202_lcd_resources[] = {
-+ [0] = {
-+ .start = AT91_CHIPSELECT_2,
-+ .end = AT91_CHIPSELECT_2 + 0x200FF,
-+ .flags = IORESOURCE_MEM
-+ },
-+ [1] = { /* reset pin */
-+ .start = AT91_PIN_PC22,
-+ .end = AT91_PIN_PC22,
-+ .flags = IORESOURCE_MEM
-+ },
-+};
-+
-+static struct platform_device kb9202_lcd_device = {
-+ .name = "s1d15605fb",
-+ .id = 0,
-+ .num_resources = ARRAY_SIZE(kb9202_lcd_resources),
-+ .resource = kb9202_lcd_resources,
-+};
-+
-+static void __init kb9202_add_device_lcd(void)
-+{
-+ /* In case the boot loader did not set the chip select mode and timing */
-+ at91_sys_write(AT91_SMC_CSR(2),
-+ AT91_SMC_WSEN | AT91_SMC_NWS_(18) | AT91_SMC_TDF_(1) | AT91_SMC_DBW_8 |
-+ AT91_SMC_RWSETUP_(1) | AT91_SMC_RWHOLD_(1));
-+
-+ /* Backlight pin = output, off */
-+ at91_set_gpio_output(AT91_PIN_PC23, 0);
-+
-+ /* Reset pin = output, in reset */
-+ at91_set_gpio_output(AT91_PIN_PC22, 0);
-+
-+ platform_device_register(&kb9202_lcd_device);
-+}
-+#else
-+static void __init kb9202_add_device_lcd(void) {}
-+#endif
-+
- static void __init kb9202_board_init(void)
- {
- /* Serial */
-@@ -129,6 +173,8 @@ static void __init kb9202_board_init(voi
- at91_add_device_spi(NULL, 0);
- /* NAND */
- at91_add_device_nand(&kb9202_nand_data);
-+ /* LCD */
-+ kb9202_add_device_lcd();
- }
-
- MACHINE_START(KB9200, "KB920x")
-Index: linux-2.6.22.19/arch/arm/mach-at91/board-sam9261ek.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/board-sam9261ek.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/board-sam9261ek.c
-@@ -27,6 +27,9 @@
- #include <linux/spi/spi.h>
- #include <linux/spi/ads7846.h>
- #include <linux/dm9000.h>
-+#include <linux/fb.h>
-+
-+#include <video/atmel_lcdc.h>
-
- #include <asm/hardware.h>
- #include <asm/setup.h>
-@@ -251,6 +254,7 @@ static struct spi_board_info ek_spi_devi
- .bus_num = 0,
- .platform_data = &ads_info,
- .irq = AT91SAM9261_ID_IRQ0,
-+ .controller_data = AT91_PIN_PA28, /* CS pin */
- },
- #endif
- #if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
-@@ -271,6 +275,65 @@ static struct spi_board_info ek_spi_devi
- };
-
-
-+/*
-+ * LCD Controller
-+ */
-+#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
-+static struct fb_videomode at91_tft_vga_modes[] = {
-+ {
-+ .name = "TX09D50VM1CCA @ 60",
-+ .refresh = 60,
-+ .xres = 240, .yres = 320,
-+ .pixclock = KHZ2PICOS(4965),
-+
-+ .left_margin = 1, .right_margin = 33,
-+ .upper_margin = 1, .lower_margin = 0,
-+ .hsync_len = 5, .vsync_len = 1,
-+
-+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-+ .vmode = FB_VMODE_NONINTERLACED,
-+ },
-+};
-+
-+static struct fb_monspecs at91fb_default_monspecs = {
-+ .manufacturer = "HIT",
-+ .monitor = "TX09D50VM1CCA",
-+
-+ .modedb = at91_tft_vga_modes,
-+ .modedb_len = ARRAY_SIZE(at91_tft_vga_modes),
-+ .hfmin = 15000,
-+ .hfmax = 64000,
-+ .vfmin = 50,
-+ .vfmax = 150,
-+};
-+
-+#define AT91SAM9261_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
-+ | ATMEL_LCDC_DISTYPE_TFT \
-+ | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-+
-+static void at91_lcdc_power_control(int on)
-+{
-+ if (on)
-+ at91_set_gpio_value(AT91_PIN_PA12, 0); /* power up */
-+ else
-+ at91_set_gpio_value(AT91_PIN_PA12, 1); /* power down */
-+}
-+
-+/* Driver datas */
-+static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
-+ .default_bpp = 16,
-+ .default_dmacon = ATMEL_LCDC_DMAEN,
-+ .default_lcdcon2 = AT91SAM9261_DEFAULT_LCDCON2,
-+ .default_monspecs = &at91fb_default_monspecs,
-+ .atmel_lcdfb_power_control = at91_lcdc_power_control,
-+ .guard_time = 1,
-+};
-+
-+#else
-+static struct atmel_lcdfb_info __initdata ek_lcdc_data;
-+#endif
-+
-+
- static void __init ek_board_init(void)
- {
- /* Serial */
-@@ -296,6 +359,8 @@ static void __init ek_board_init(void)
- /* MMC */
- at91_add_device_mmc(0, &ek_mmc_data);
- #endif
-+ /* LCD Controller */
-+ at91_add_device_lcdc(&ek_lcdc_data);
- }
-
- MACHINE_START(AT91SAM9261EK, "Atmel AT91SAM9261-EK")
-Index: linux-2.6.22.19/arch/arm/mach-at91/board-sam9263ek.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/board-sam9263ek.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/board-sam9263ek.c
-@@ -26,6 +26,9 @@
- #include <linux/platform_device.h>
- #include <linux/spi/spi.h>
- #include <linux/spi/ads7846.h>
-+#include <linux/fb.h>
-+
-+#include <video/atmel_lcdc.h>
-
- #include <asm/hardware.h>
- #include <asm/setup.h>
-@@ -202,6 +205,65 @@ static struct at91_nand_data __initdata
-
-
- /*
-+ * LCD Controller
-+ */
-+#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
-+static struct fb_videomode at91_tft_vga_modes[] = {
-+ {
-+ .name = "TX09D50VM1CCA @ 60",
-+ .refresh = 60,
-+ .xres = 240, .yres = 320,
-+ .pixclock = KHZ2PICOS(4965),
-+
-+ .left_margin = 1, .right_margin = 33,
-+ .upper_margin = 1, .lower_margin = 0,
-+ .hsync_len = 5, .vsync_len = 1,
-+
-+ .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-+ .vmode = FB_VMODE_NONINTERLACED,
-+ },
-+};
-+
-+static struct fb_monspecs at91fb_default_monspecs = {
-+ .manufacturer = "HIT",
-+ .monitor = "TX09D70VM1CCA",
-+
-+ .modedb = at91_tft_vga_modes,
-+ .modedb_len = ARRAY_SIZE(at91_tft_vga_modes),
-+ .hfmin = 15000,
-+ .hfmax = 64000,
-+ .vfmin = 50,
-+ .vfmax = 150,
-+};
-+
-+#define AT91SAM9263_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
-+ | ATMEL_LCDC_DISTYPE_TFT \
-+ | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-+
-+static void at91_lcdc_power_control(int on)
-+{
-+ if (on)
-+ at91_set_gpio_value(AT91_PIN_PD12, 0); /* power up */
-+ else
-+ at91_set_gpio_value(AT91_PIN_PD12, 1); /* power down */
-+}
-+
-+/* Driver datas */
-+static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
-+ .default_bpp = 16,
-+ .default_dmacon = ATMEL_LCDC_DMAEN,
-+ .default_lcdcon2 = AT91SAM9263_DEFAULT_LCDCON2,
-+ .default_monspecs = &at91fb_default_monspecs,
-+ .atmel_lcdfb_power_control = at91_lcdc_power_control,
-+ .guard_time = 1,
-+};
-+
-+#else
-+static struct atmel_lcdfb_info __initdata ek_lcdc_data;
-+#endif
-+
-+
-+/*
- * AC97
- */
- static struct atmel_ac97_data ek_ac97_data = {
-@@ -230,6 +292,8 @@ static void __init ek_board_init(void)
- at91_add_device_nand(&ek_nand_data);
- /* I2C */
- at91_add_device_i2c();
-+ /* LCD Controller */
-+ at91_add_device_lcdc(&ek_lcdc_data);
- /* AC97 */
- at91_add_device_ac97(&ek_ac97_data);
- }
-Index: linux-2.6.22.19/arch/arm/mach-at91/clock.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/clock.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/clock.c
-@@ -32,6 +32,7 @@
- #include <asm/arch/cpu.h>
-
- #include "clock.h"
-+#include "generic.h"
-
-
- /*
-@@ -254,6 +255,23 @@ EXPORT_SYMBOL(clk_get_rate);
-
- /*------------------------------------------------------------------------*/
-
-+#ifdef CONFIG_PM
-+
-+int clk_must_disable(struct clk *clk)
-+{
-+ if (!at91_suspend_entering_slow_clock())
-+ return 0;
-+
-+ while (clk->parent)
-+ clk = clk->parent;
-+ return clk != &clk32k;
-+}
-+EXPORT_SYMBOL(clk_must_disable);
-+
-+#endif
-+
-+/*------------------------------------------------------------------------*/
-+
- #ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS
-
- /*
-Index: linux-2.6.22.19/arch/arm/mach-at91/generic.h
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/generic.h
-+++ linux-2.6.22.19/arch/arm/mach-at91/generic.h
-@@ -36,6 +36,7 @@ extern void __init at91_clock_associate(
- /* Power Management */
- extern void at91_irq_suspend(void);
- extern void at91_irq_resume(void);
-+extern int at91_suspend_entering_slow_clock(void);
-
- /* GPIO */
- #define AT91RM9200_PQFP 3 /* AT91RM9200 PQFP package has 3 banks */
-Index: linux-2.6.22.19/arch/arm/mach-at91/ics1523.c
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/arch/arm/mach-at91/ics1523.c
-@@ -0,0 +1,207 @@
-+/*
-+ * arch/arm/mach-at91rm9200/ics1523.c
-+ *
-+ * Copyright (C) 2003 ATMEL Rousset
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+
-+#include <asm/hardware.h>
-+#include <asm/io.h>
-+
-+#include <linux/clk.h>
-+#include <linux/delay.h>
-+#include <linux/err.h>
-+#include <linux/init.h>
-+
-+#include <asm/arch/ics1523.h>
-+#include <asm/arch/at91_twi.h>
-+#include <asm/arch/gpio.h>
-+
-+/* TWI Errors */
-+#define AT91_TWI_ERROR (AT91_TWI_NACK | AT91_TWI_UNRE | AT91_TWI_OVRE)
-+
-+
-+static void __iomem *twi_base;
-+
-+#define at91_twi_read(reg) __raw_readl(twi_base + (reg))
-+#define at91_twi_write(reg, val) __raw_writel((val), twi_base + (reg))
-+
-+
-+/* -----------------------------------------------------------------------------
-+ * Initialization of TWI CLOCK
-+ * ----------------------------------------------------------------------------- */
-+
-+static void at91_ics1523_SetTwiClock(unsigned int mck_khz)
-+{
-+ int sclock;
-+
-+ /* Here, CKDIV = 1 and CHDIV = CLDIV ==> CLDIV = CHDIV = 1/4*((Fmclk/FTWI) -6) */
-+ sclock = (10*mck_khz / ICS_TRANSFER_RATE);
-+ if (sclock % 10 >= 5)
-+ sclock = (sclock /10) - 5;
-+ else
-+ sclock = (sclock /10)- 6;
-+ sclock = (sclock + (4 - sclock %4)) >> 2; /* div 4 */
-+
-+ at91_twi_write(AT91_TWI_CWGR, 0x00010000 | sclock | (sclock << 8));
-+}
-+
-+/* -----------------------------------------------------------------------------
-+ * Read a byte with TWI Interface from the Clock Generator ICS1523
-+ * ----------------------------------------------------------------------------- */
-+
-+static int at91_ics1523_ReadByte(unsigned char reg_address, unsigned char *data_in)
-+{
-+ int Status, nb_trial;
-+
-+ at91_twi_write(AT91_TWI_MMR, AT91_TWI_MREAD | AT91_TWI_IADRSZ_1 | ((ICS_ADDR << 16) & AT91_TWI_DADR));
-+ at91_twi_write(AT91_TWI_IADR, reg_address);
-+ at91_twi_write(AT91_TWI_CR, AT91_TWI_START | AT91_TWI_STOP);
-+
-+ /* Program temporizing period (300us) */
-+ udelay(300);
-+
-+ /* Wait TXcomplete ... */
-+ nb_trial = 0;
-+ Status = at91_twi_read(AT91_TWI_SR);
-+ while (!(Status & AT91_TWI_TXCOMP) && (nb_trial < 10)) {
-+ nb_trial++;
-+ Status = at91_twi_read(AT91_TWI_SR);
-+ }
-+
-+ if (Status & AT91_TWI_TXCOMP) {
-+ *data_in = (unsigned char) at91_twi_read(AT91_TWI_RHR);
-+ return ICS1523_ACCESS_OK;
-+ }
-+ else
-+ return ICS1523_ACCESS_ERROR;
-+}
-+
-+/* -----------------------------------------------------------------------------
-+ * Write a byte with TWI Interface to the Clock Generator ICS1523
-+ * ----------------------------------------------------------------------------- */
-+
-+static int at91_ics1523_WriteByte(unsigned char reg_address, unsigned char data_out)
-+{
-+ int Status, nb_trial;
-+
-+ at91_twi_write(AT91_TWI_MMR, AT91_TWI_IADRSZ_1 | ((ICS_ADDR << 16) & AT91_TWI_DADR));
-+ at91_twi_write(AT91_TWI_IADR, reg_address);
-+ at91_twi_write(AT91_TWI_THR, data_out);
-+ at91_twi_write(AT91_TWI_CR, AT91_TWI_START | AT91_TWI_STOP);
-+
-+ /* Program temporizing period (300us) */
-+ udelay(300);
-+
-+ nb_trial = 0;
-+ Status = at91_twi_read(AT91_TWI_SR);
-+ while (!(Status & AT91_TWI_TXCOMP) && (nb_trial < 10)) {
-+ nb_trial++;
-+ if (Status & AT91_TWI_ERROR) {
-+ /* If Underrun OR NACK - Start again */
-+ at91_twi_write(AT91_TWI_CR, AT91_TWI_START | AT91_TWI_STOP);
-+
-+ /* Program temporizing period (300us) */
-+ udelay(300);
-+ }
-+ Status = at91_twi_read(AT91_TWI_SR);
-+ };
-+
-+ if (Status & AT91_TWI_TXCOMP)
-+ return ICS1523_ACCESS_OK;
-+ else
-+ return ICS1523_ACCESS_ERROR;
-+}
-+
-+/* -----------------------------------------------------------------------------
-+ * Initialization of the Clock Generator ICS1523
-+ * ----------------------------------------------------------------------------- */
-+
-+int at91_ics1523_init(void)
-+{
-+ int nb_trial;
-+ int ack = ICS1523_ACCESS_OK;
-+ unsigned int status = 0xffffffff;
-+ struct clk *twi_clk;
-+
-+ /* Map in TWI peripheral */
-+ twi_base = ioremap(AT91RM9200_BASE_TWI, SZ_16K);
-+ if (!twi_base)
-+ return -ENOMEM;
-+
-+ /* pins used for TWI interface */
-+ at91_set_A_periph(AT91_PIN_PA25, 0); /* TWD */
-+ at91_set_multi_drive(AT91_PIN_PA25, 1);
-+ at91_set_A_periph(AT91_PIN_PA26, 0); /* TWCK */
-+ at91_set_multi_drive(AT91_PIN_PA26, 1);
-+
-+ /* Enable the TWI clock */
-+ twi_clk = clk_get(NULL, "twi_clk");
-+ if (IS_ERR(twi_clk))
-+ return ICS1523_ACCESS_ERROR;
-+ clk_enable(twi_clk);
-+
-+ /* Disable interrupts */
-+ at91_twi_write(AT91_TWI_IDR, -1);
-+
-+ /* Reset peripheral */
-+ at91_twi_write(AT91_TWI_CR, AT91_TWI_SWRST);
-+
-+ /* Set Master mode */
-+ at91_twi_write(AT91_TWI_CR, AT91_TWI_MSEN);
-+
-+ /* Set TWI Clock Waveform Generator Register */
-+ at91_ics1523_SetTwiClock(60000); /* MCK in KHz = 60000 KHz */
-+
-+ /* ICS1523 Initialisation */
-+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_ICR, (unsigned char) 0);
-+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_OE, (unsigned char) (ICS_OEF | ICS_OET2 | ICS_OETCK));
-+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_OD, (unsigned char) (ICS_INSEL | 0x7F));
-+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_DPAO, (unsigned char) 0);
-+
-+ nb_trial = 0;
-+ do {
-+ nb_trial++;
-+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_ICR, (unsigned char) (ICS_ENDLS | ICS_ENPLS | ICS_PDEN /*| ICS_FUNCSEL*/));
-+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_LCR, (unsigned char) (ICS_PSD | ICS_PFD));
-+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_FD0, (unsigned char) 0x39) ; /* 0x7A */
-+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_FD1, (unsigned char) 0x00);
-+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_SWRST, (unsigned char) (ICS_PLLR));
-+
-+ /* Program 1ms temporizing period */
-+ mdelay(1);
-+
-+ at91_ics1523_ReadByte ((unsigned char) ICS_SR, (char *)&status);
-+ } while (!((unsigned int) status & (unsigned int) ICS_PLLLOCK) && (nb_trial < 10));
-+
-+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_DPAC, (unsigned char) 0x03) ; /* 0x01 */
-+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_SWRST, (unsigned char) (ICS_DPAR));
-+
-+ /* Program 1ms temporizing period */
-+ mdelay(1);
-+
-+ ack |= at91_ics1523_WriteByte ((unsigned char) ICS_DPAO, (unsigned char) 0x00);
-+
-+ /* Program 1ms temporizing period */
-+ mdelay(1);
-+
-+ /* All done - cleanup */
-+ iounmap(twi_base);
-+ clk_disable(twi_clk);
-+ clk_put(twi_clk);
-+
-+ return ack;
-+}
-Index: linux-2.6.22.19/arch/arm/mach-at91/Kconfig
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/Kconfig
-+++ linux-2.6.22.19/arch/arm/mach-at91/Kconfig
-@@ -97,6 +97,12 @@ config MACH_KAFA
- help
- Select this if you are using Sperry-Sun's KAFA board.
-
-+config MACH_CHUB
-+ bool "Promwad Chub board"
-+ depends on ARCH_AT91RM9200
-+ help
-+ Select this if you are using Promwad's Chub board.
-+
- endif
-
- # ----------------------------------------------------------
-@@ -121,6 +127,13 @@ config MACH_AT91SAM9260EK
- Select this if you are using Atmel's AT91SAM9260-EK or AT91SAM9XE Evaluation Kit
- <http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3933>
-
-+config MACH_CAM60
-+ bool "KwikByte CAM60 board"
-+ depends on ARCH_AT91SAM9260
-+ help
-+ Select this if you are using KwikByte's CAM60 board based on the Atmel AT91SAM9260.
-+ <http://www.kwikbyte.com>
-+
- endif
-
- # ----------------------------------------------------------
-@@ -184,6 +197,20 @@ config MTD_NAND_AT91_BUSWIDTH_16
- On AT91SAM926x boards both types of NAND flash can be present
- (8 and 16 bit data bus width).
-
-+config CSB300_WAKE_SW0
-+ bool "CSB300 SW0 irq0 wakeup"
-+ depends on MACH_CSB337 && PM
-+ help
-+ If you have a CSB300 connected to your CSB337, this lets
-+ SW0 serve as a wakeup button. It uses IRQ0.
-+
-+config CSB300_WAKE_SW1
-+ bool "CSB300 SW1 gpio wakeup"
-+ depends on MACH_CSB337 && PM
-+ help
-+ If you have a CSB300 connected to your CSB337, this lets
-+ SW1 serve as a wakeup button. It uses GPIO.
-+
- # ----------------------------------------------------------
-
- comment "AT91 Feature Selections"
-@@ -194,6 +221,20 @@ config AT91_PROGRAMMABLE_CLOCKS
- Select this if you need to program one or more of the PCK0..PCK3
- programmable clock outputs.
-
-+config ATMEL_TCLIB
-+ bool "Timer/Counter Library"
-+ help
-+ Select this if you want a library to allocate the Timer/Counter
-+ blocks found on many Atmel processors. This facilitates using
-+ these modules despite processor differences.
-+
-+config AT91_SLOW_CLOCK
-+ bool "Suspend-to-RAM uses slow clock mode (EXPERIMENTAL)"
-+ depends on PM && EXPERIMENTAL
-+ help
-+ Select this if you wish to put the CPU into slow clock mode
-+ while in the "Suspend to RAM" state, to save more power.
-+
- endmenu
-
- endif
-Index: linux-2.6.22.19/arch/arm/mach-at91/Makefile
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/Makefile
-+++ linux-2.6.22.19/arch/arm/mach-at91/Makefile
-@@ -8,6 +8,8 @@ obj-n :=
- obj- :=
-
- obj-$(CONFIG_PM) += pm.o
-+obj-$(CONFIG_AT91_SLOW_CLOCK) += pm_slowclock.o
-+obj-$(CONFIG_ATMEL_TCLIB) += tclib.o
-
- # CPU-specific support
- obj-$(CONFIG_ARCH_AT91RM9200) += at91rm9200.o at91rm9200_time.o at91rm9200_devices.o
-@@ -26,10 +28,12 @@ obj-$(CONFIG_MACH_CARMEVA) += board-carm
- obj-$(CONFIG_MACH_KB9200) += board-kb9202.o
- obj-$(CONFIG_MACH_ATEB9200) += board-eb9200.o
- obj-$(CONFIG_MACH_KAFA) += board-kafa.o
-+obj-$(CONFIG_MACH_CHUB) += board-chub.o
- obj-$(CONFIG_MACH_PICOTUX2XX) += board-picotux200.o
-
- # AT91SAM9260 board-specific support
- obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o
-+obj-$(CONFIG_MACH_CAM60) += board-cam60.o
-
- # AT91SAM9261 board-specific support
- obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o
-@@ -51,7 +55,7 @@ led-$(CONFIG_MACH_KAFA) += leds.o
- obj-$(CONFIG_LEDS) += $(led-y)
-
- # VGA support
--#obj-$(CONFIG_FB_S1D13XXX) += ics1523.o
-+obj-$(CONFIG_FB_S1D13XXX) += ics1523.o
-
-
- ifeq ($(CONFIG_PM_DEBUG),y)
-Index: linux-2.6.22.19/arch/arm/mach-at91/pm.c
-===================================================================
---- linux-2.6.22.19.orig/arch/arm/mach-at91/pm.c
-+++ linux-2.6.22.19/arch/arm/mach-at91/pm.c
-@@ -63,6 +63,7 @@ static int at91_pm_set_target(suspend_st
- * Verify that all the clocks are correct before entering
- * slow-clock mode.
- */
-+#warning "SAM9260 only has 3 programmable clocks."
- static int at91_pm_verify_clocks(void)
- {
- unsigned long scsr;
-@@ -103,20 +104,15 @@ static int at91_pm_verify_clocks(void)
- }
-
- /*
-- * Call this from platform driver suspend() to see how deeply to suspend.
-+ * This is called from clk_must_disable(), to see how deeply to suspend.
- * For example, some controllers (like OHCI) need one of the PLL clocks
- * in order to act as a wakeup source, and those are not available when
- * going into slow clock mode.
-- *
-- * REVISIT: generalize as clk_will_be_available(clk)? Other platforms have
-- * the very same problem (but not using at91 main_clk), and it'd be better
-- * to add one generic API rather than lots of platform-specific ones.
- */
- int at91_suspend_entering_slow_clock(void)
- {
- return (target_state == PM_SUSPEND_MEM);
- }
--EXPORT_SYMBOL(at91_suspend_entering_slow_clock);
-
-
- static void (*slow_clock)(void);
-@@ -205,16 +201,23 @@ static struct pm_ops at91_pm_ops ={
- .enter = at91_pm_enter,
- };
-
-+#ifdef CONFIG_AT91_SLOW_CLOCK
-+extern void at91rm9200_slow_clock(void);
-+extern u32 at91rm9200_slow_clock_sz;
-+#endif
-+
- static int __init at91_pm_init(void)
- {
-- printk("AT91: Power Management\n");
--
--#ifdef CONFIG_AT91_PM_SLOW_CLOCK
-- /* REVISIT allocations of SRAM should be dynamically managed.
-+#ifdef CONFIG_AT91_SLOW_CLOCK
-+ /*
-+ * REVISIT allocations of SRAM should be dynamically managed.
- * FIQ handlers and other components will want SRAM/TCM too...
- */
-- slow_clock = (void *) (AT91_VA_BASE_SRAM + (3 * SZ_4K));
-+ slow_clock = (void *) (AT91_IO_VIRT_BASE - AT91RM9200_SRAM_SIZE + (3 * SZ_4K));
- memcpy(slow_clock, at91rm9200_slow_clock, at91rm9200_slow_clock_sz);
-+ printk("AT91: Power Management (with slow clock mode)\n");
-+#else
-+ printk("AT91: Power Management\n");
- #endif
-
- /* Disable SDRAM low-power mode. Cannot be used with self-refresh. */
-Index: linux-2.6.22.19/arch/arm/mach-at91/pm.c.orig
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/arch/arm/mach-at91/pm.c.orig
-@@ -0,0 +1,227 @@
-+/*
-+ * arch/arm/mach-at91/pm.c
-+ * AT91 Power Management
-+ *
-+ * Copyright (C) 2005 David Brownell
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ */
-+
-+#include <linux/pm.h>
-+#include <linux/sched.h>
-+#include <linux/proc_fs.h>
-+#include <linux/pm.h>
-+#include <linux/interrupt.h>
-+#include <linux/sysfs.h>
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+
-+#include <asm/io.h>
-+#include <asm/irq.h>
-+#include <asm/atomic.h>
-+#include <asm/mach/time.h>
-+#include <asm/mach/irq.h>
-+#include <asm/mach-types.h>
-+
-+#include <asm/arch/at91_pmc.h>
-+#include <asm/arch/at91rm9200_mc.h>
-+#include <asm/arch/gpio.h>
-+#include <asm/arch/cpu.h>
-+
-+#include "generic.h"
-+
-+
-+static int at91_pm_valid_state(suspend_state_t state)
-+{
-+ switch (state) {
-+ case PM_SUSPEND_ON:
-+ case PM_SUSPEND_STANDBY:
-+ case PM_SUSPEND_MEM:
-+ return 1;
-+
-+ default:
-+ return 0;
-+ }
-+}
-+
-+
-+static suspend_state_t target_state;
-+
-+/*
-+ * Called after processes are frozen, but before we shutdown devices.
-+ */
-+static int at91_pm_prepare(suspend_state_t state)
-+{
-+ target_state = state;
-+ return 0;
-+}
-+
-+/*
-+ * Verify that all the clocks are correct before entering
-+ * slow-clock mode.
-+ */
-+static int at91_pm_verify_clocks(void)
-+{
-+ unsigned long scsr;
-+ int i;
-+
-+ scsr = at91_sys_read(AT91_PMC_SCSR);
-+
-+ /* USB must not be using PLLB */
-+ if (cpu_is_at91rm9200()) {
-+ if ((scsr & (AT91RM9200_PMC_UHP | AT91RM9200_PMC_UDP)) != 0) {
-+ pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n");
-+ return 0;
-+ }
-+ } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263()) {
-+ if ((scsr & (AT91SAM926x_PMC_UHP | AT91SAM926x_PMC_UDP)) != 0) {
-+ pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n");
-+ return 0;
-+ }
-+ }
-+
-+#ifdef CONFIG_AT91_PROGRAMMABLE_CLOCKS
-+ /* PCK0..PCK3 must be disabled, or configured to use clk32k */
-+ for (i = 0; i < 4; i++) {
-+ u32 css;
-+
-+ if ((scsr & (AT91_PMC_PCK0 << i)) == 0)
-+ continue;
-+
-+ css = at91_sys_read(AT91_PMC_PCKR(i)) & AT91_PMC_CSS;
-+ if (css != AT91_PMC_CSS_SLOW) {
-+ pr_debug("AT91: PM - Suspend-to-RAM with PCK%d src %d\n", i, css);
-+ return 0;
-+ }
-+ }
-+#endif
-+
-+ return 1;
-+}
-+
-+/*
-+ * Call this from platform driver suspend() to see how deeply to suspend.
-+ * For example, some controllers (like OHCI) need one of the PLL clocks
-+ * in order to act as a wakeup source, and those are not available when
-+ * going into slow clock mode.
-+ *
-+ * REVISIT: generalize as clk_will_be_available(clk)? Other platforms have
-+ * the very same problem (but not using at91 main_clk), and it'd be better
-+ * to add one generic API rather than lots of platform-specific ones.
-+ */
-+int at91_suspend_entering_slow_clock(void)
-+{
-+ return (target_state == PM_SUSPEND_MEM);
-+}
-+EXPORT_SYMBOL(at91_suspend_entering_slow_clock);
-+
-+
-+static void (*slow_clock)(void);
-+
-+
-+static int at91_pm_enter(suspend_state_t state)
-+{
-+ at91_gpio_suspend();
-+ at91_irq_suspend();
-+
-+ pr_debug("AT91: PM - wake mask %08x, pm state %d\n",
-+ /* remember all the always-wake irqs */
-+ (at91_sys_read(AT91_PMC_PCSR)
-+ | (1 << AT91_ID_FIQ)
-+ | (1 << AT91_ID_SYS)
-+ | (at91_extern_irq))
-+ & at91_sys_read(AT91_AIC_IMR),
-+ state);
-+
-+ switch (state) {
-+ /*
-+ * Suspend-to-RAM is like STANDBY plus slow clock mode, so
-+ * drivers must suspend more deeply: only the master clock
-+ * controller may be using the main oscillator.
-+ */
-+ case PM_SUSPEND_MEM:
-+ /*
-+ * Ensure that clocks are in a valid state.
-+ */
-+ if (!at91_pm_verify_clocks())
-+ goto error;
-+
-+ /*
-+ * Enter slow clock mode by switching over to clk32k and
-+ * turning off the main oscillator; reverse on wakeup.
-+ */
-+ if (slow_clock) {
-+ slow_clock();
-+ break;
-+ } else {
-+ /* DEVELOPMENT ONLY */
-+ pr_info("AT91: PM - no slow clock mode yet ...\n");
-+ /* FALLTHROUGH leaving master clock alone */
-+ }
-+
-+ /*
-+ * STANDBY mode has *all* drivers suspended; ignores irqs not
-+ * marked as 'wakeup' event sources; and reduces DRAM power.
-+ * But otherwise it's identical to PM_SUSPEND_ON: cpu idle, and
-+ * nothing fancy done with main or cpu clocks.
-+ */
-+ case PM_SUSPEND_STANDBY:
-+ /*
-+ * NOTE: the Wait-for-Interrupt instruction needs to be
-+ * in icache so the SDRAM stays in self-refresh mode until
-+ * the wakeup IRQ occurs.
-+ */
-+ asm("b 1f; .align 5; 1:");
-+ asm("mcr p15, 0, r0, c7, c10, 4"); /* drain write buffer */
-+ at91_sys_write(AT91_SDRAMC_SRR, 1); /* self-refresh mode */
-+ /* fall though to next state */
-+
-+ case PM_SUSPEND_ON:
-+ asm("mcr p15, 0, r0, c7, c0, 4"); /* wait for interrupt */
-+ break;
-+
-+ default:
-+ pr_debug("AT91: PM - bogus suspend state %d\n", state);
-+ goto error;
-+ }
-+
-+ pr_debug("AT91: PM - wakeup %08x\n",
-+ at91_sys_read(AT91_AIC_IPR) & at91_sys_read(AT91_AIC_IMR));
-+
-+error:
-+ target_state = PM_SUSPEND_ON;
-+ at91_irq_resume();
-+ at91_gpio_resume();
-+ return 0;
-+}
-+
-+
-+static struct pm_ops at91_pm_ops ={
-+ .valid = at91_pm_valid_state,
-+ .prepare = at91_pm_prepare,
-+ .enter = at91_pm_enter,
-+};
-+
-+static int __init at91_pm_init(void)
-+{
-+ printk("AT91: Power Management\n");
-+
-+#ifdef CONFIG_AT91_PM_SLOW_CLOCK
-+ /* REVISIT allocations of SRAM should be dynamically managed.
-+ * FIQ handlers and other components will want SRAM/TCM too...
-+ */
-+ slow_clock = (void *) (AT91_VA_BASE_SRAM + (3 * SZ_4K));
-+ memcpy(slow_clock, at91rm9200_slow_clock, at91rm9200_slow_clock_sz);
-+#endif
-+
-+ /* Disable SDRAM low-power mode. Cannot be used with self-refresh. */
-+ at91_sys_write(AT91_SDRAMC_LPR, 0);
-+
-+ pm_set_ops(&at91_pm_ops);
-+
-+ return 0;
-+}
-+arch_initcall(at91_pm_init);
-Index: linux-2.6.22.19/arch/arm/mach-at91/pm_slowclock.S
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/arch/arm/mach-at91/pm_slowclock.S
-@@ -0,0 +1,172 @@
-+/*
-+ * arch/arm/mach-at91/pm_slow_clock.S
-+ *
-+ * Copyright (C) 2006 Savin Zlobec
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ *
-+ */
-+
-+#include <linux/linkage.h>
-+#include <asm/hardware.h>
-+#include <asm/arch/at91_pmc.h>
-+#include <asm/arch/at91rm9200_mc.h>
-+
-+#define MCKRDY_TIMEOUT 1000
-+#define MOSCRDY_TIMEOUT 1000
-+#define PLLALOCK_TIMEOUT 1000
-+
-+ .macro wait_mckrdy
-+ mov r2, #MCKRDY_TIMEOUT
-+1: sub r2, r2, #1
-+ cmp r2, #0
-+ beq 2f
-+ ldr r3, [r1, #AT91_PMC_SR]
-+ tst r3, #AT91_PMC_MCKRDY
-+ beq 1b
-+2:
-+ .endm
-+
-+ .macro wait_moscrdy
-+ mov r2, #MOSCRDY_TIMEOUT
-+1: sub r2, r2, #1
-+ cmp r2, #0
-+ beq 2f
-+ ldr r3, [r1, #AT91_PMC_SR]
-+ tst r3, #AT91_PMC_MOSCS
-+ beq 1b
-+2:
-+ .endm
-+
-+ .macro wait_pllalock
-+ mov r2, #PLLALOCK_TIMEOUT
-+1: sub r2, r2, #1
-+ cmp r2, #0
-+ beq 2f
-+ ldr r3, [r1, #AT91_PMC_SR]
-+ tst r3, #AT91_PMC_LOCKA
-+ beq 1b
-+2:
-+ .endm
-+
-+ .macro wait_plladis
-+ mov r2, #PLLALOCK_TIMEOUT
-+1: sub r2, r2, #1
-+ cmp r2, #0
-+ beq 2f
-+ ldr r3, [r1, #AT91_PMC_SR]
-+ tst r3, #AT91_PMC_LOCKA
-+ bne 1b
-+2:
-+ .endm
-+
-+ .text
-+
-+ENTRY(at91rm9200_slow_clock)
-+
-+ ldr r1, .at91_va_base_sys
-+
-+ /* Put SDRAM in self refresh mode */
-+
-+ b 1f
-+ .align 5
-+1: mcr p15, 0, r0, c7, c10, 4
-+ mov r2, #1
-+ str r2, [r1, #AT91_SDRAMC_SRR]
-+
-+ /* Save Master clock setting */
-+
-+ ldr r2, [r1, #AT91_PMC_MCKR]
-+ str r2, .saved_mckr
-+
-+ /*
-+ * Set the Master clock source to slow clock
-+ *
-+ * First set the CSS field, wait for MCKRDY
-+ * and than set the PRES and MDIV fields.
-+ *
-+ * See eratta #2[78] for details.
-+ */
-+
-+ bic r2, r2, #3
-+ str r2, [r1, #AT91_PMC_MCKR]
-+
-+ wait_mckrdy
-+
-+ mov r2, #0
-+ str r2, [r1, #AT91_PMC_MCKR]
-+
-+ /* Save PLLA setting and disable it */
-+
-+ ldr r2, [r1, #AT91_CKGR_PLLAR]
-+ str r2, .saved_pllar
-+
-+ mov r2, #0
-+ str r2, [r1, #AT91_CKGR_PLLAR]
-+
-+ wait_plladis
-+
-+ /* Turn off the main oscillator */
-+
-+ ldr r2, [r1, #AT91_CKGR_MOR]
-+ bic r2, r2, #AT91_PMC_MOSCEN
-+ str r2, [r1, #AT91_CKGR_MOR]
-+
-+ /* Wait for interrupt */
-+
-+ mcr p15, 0, r0, c7, c0, 4
-+
-+ /* Turn on the main oscillator */
-+
-+ ldr r2, [r1, #AT91_CKGR_MOR]
-+ orr r2, r2, #AT91_PMC_MOSCEN
-+ str r2, [r1, #AT91_CKGR_MOR]
-+
-+ wait_moscrdy
-+
-+ /* Restore PLLA setting */
-+
-+ ldr r2, .saved_pllar
-+ str r2, [r1, #AT91_CKGR_PLLAR]
-+
-+ wait_pllalock
-+
-+ /*
-+ * Restore master clock setting
-+ *
-+ * First set PRES if it was not 0,
-+ * than set CSS and MDIV fields.
-+ * After every change wait for
-+ * MCKRDY.
-+ *
-+ * See eratta #2[78] for details.
-+ */
-+
-+ ldr r2, .saved_mckr
-+ tst r2, #0x1C
-+ beq 2f
-+ and r2, r2, #0x1C
-+ str r2, [r1, #AT91_PMC_MCKR]
-+
-+ wait_mckrdy
-+
-+2: ldr r2, .saved_mckr
-+ str r2, [r1, #AT91_PMC_MCKR]
-+
-+ wait_mckrdy
-+
-+ mov pc, lr
-+
-+.saved_mckr:
-+ .word 0
-+
-+.saved_pllar:
-+ .word 0
-+
-+.at91_va_base_sys:
-+ .word AT91_VA_BASE_SYS
-+
-+ENTRY(at91rm9200_slow_clock_sz)
-+ .word .-at91rm9200_slow_clock
-Index: linux-2.6.22.19/arch/arm/mach-at91/tclib.c
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/arch/arm/mach-at91/tclib.c
-@@ -0,0 +1,17 @@
-+#include <linux/clk.h>
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+
-+#include "tclib.h"
-+
-+static struct atmel_tcblock *blocks;
-+static int nblocks;
-+
-+/*
-+ * Called from the processor-specific init to register the TC Blocks.
-+ */
-+void __init atmel_tc_init(struct atmel_tcblock *tcblocks, int n)
-+{
-+ blocks = tcblocks;
-+ nblocks = n;
-+}
-Index: linux-2.6.22.19/arch/arm/mach-at91/tclib.h
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/arch/arm/mach-at91/tclib.h
-@@ -0,0 +1,11 @@
-+
-+#define TC_PER_TCB 3
-+
-+struct atmel_tcblock {
-+ u32 physaddr;
-+ void __iomem *ioaddr;
-+ struct clk *clk[TC_PER_TCB];
-+ int irq[TC_PER_TCB];
-+};
-+
-+extern void __init atmel_tc_init(struct atmel_tcblock *tcblocks, int n);
-Index: linux-2.6.22.19/include/asm-arm/arch-at91/at91_mci.h
-===================================================================
---- linux-2.6.22.19.orig/include/asm-arm/arch-at91/at91_mci.h
-+++ linux-2.6.22.19/include/asm-arm/arch-at91/at91_mci.h
-@@ -26,6 +26,9 @@
- #define AT91_MCI_MR 0x04 /* Mode Register */
- #define AT91_MCI_CLKDIV (0xff << 0) /* Clock Divider */
- #define AT91_MCI_PWSDIV (7 << 8) /* Power Saving Divider */
-+#define AT91_MCI_RDPROOF (1 << 11) /* Read Proof Enable [SAM926[03] only] */
-+#define AT91_MCI_WRPROOF (1 << 12) /* Write Proof Enable [SAM926[03] only] */
-+#define AT91_MCI_PDCFBYTE (1 << 13) /* PDC Force Byte Transfer [SAM926[03] only] */
- #define AT91_MCI_PDCPADV (1 << 14) /* PDC Padding Value */
- #define AT91_MCI_PDCMODE (1 << 15) /* PDC-orientated Mode */
- #define AT91_MCI_BLKLEN (0xfff << 18) /* Data Block Length */
-Index: linux-2.6.22.19/include/asm-arm/arch-at91/at91_pmc.h
-===================================================================
---- linux-2.6.22.19.orig/include/asm-arm/arch-at91/at91_pmc.h
-+++ linux-2.6.22.19/include/asm-arm/arch-at91/at91_pmc.h
-@@ -37,7 +37,9 @@
- #define AT91_PMC_PCDR (AT91_PMC + 0x14) /* Peripheral Clock Disable Register */
- #define AT91_PMC_PCSR (AT91_PMC + 0x18) /* Peripheral Clock Status Register */
-
--#define AT91_CKGR_MOR (AT91_PMC + 0x20) /* Main Oscillator Register */
-+#define AT91_CKGR_UCKR (AT91_PMC + 0x1C) /* UTMI Clock Register [SAM9RL only] */
-+
-+#define AT91_CKGR_MOR (AT91_PMC + 0x20) /* Main Oscillator Register [not on SAM9RL] */
- #define AT91_PMC_MOSCEN (1 << 0) /* Main Oscillator Enable */
- #define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass [AT91SAM926x only] */
- #define AT91_PMC_OSCOUNT (0xff << 8) /* Main Oscillator Start-up Time */
-Index: linux-2.6.22.19/include/asm-arm/arch-at91/at91sam9260_matrix.h
-===================================================================
---- linux-2.6.22.19.orig/include/asm-arm/arch-at91/at91sam9260_matrix.h
-+++ linux-2.6.22.19/include/asm-arm/arch-at91/at91sam9260_matrix.h
-@@ -67,7 +67,7 @@
- #define AT91_MATRIX_CS4A (1 << 4) /* Chip Select 4 Assignment */
- #define AT91_MATRIX_CS4A_SMC (0 << 4)
- #define AT91_MATRIX_CS4A_SMC_CF1 (1 << 4)
--#define AT91_MATRIX_CS5A (1 << 5 ) /* Chip Select 5 Assignment */
-+#define AT91_MATRIX_CS5A (1 << 5) /* Chip Select 5 Assignment */
- #define AT91_MATRIX_CS5A_SMC (0 << 5)
- #define AT91_MATRIX_CS5A_SMC_CF2 (1 << 5)
- #define AT91_MATRIX_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */
-Index: linux-2.6.22.19/include/asm-arm/arch-at91/board.h
-===================================================================
---- linux-2.6.22.19.orig/include/asm-arm/arch-at91/board.h
-+++ linux-2.6.22.19/include/asm-arm/arch-at91/board.h
-@@ -124,9 +124,21 @@ struct atmel_ac97_data {
- };
- extern void __init at91_add_device_ac97(struct atmel_ac97_data *data);
-
-+ /* ISI */
-+extern void __init at91_add_device_isi(void);
-+
- /* LEDs */
- extern u8 at91_leds_cpu;
- extern u8 at91_leds_timer;
- extern void __init at91_init_leds(u8 cpu_led, u8 timer_led);
-
-+struct at91_gpio_led {
-+ u8 index; /* index of LED */
-+ char* name; /* name of LED */
-+ u8 gpio; /* AT91_PIN_xx */
-+ u8 flags; /* 1=active-high */
-+ char* trigger; /* default trigger */
-+};
-+extern void __init at91_gpio_leds(struct at91_gpio_led *leds, int nr);
-+
- #endif
-Index: linux-2.6.22.19/include/asm-arm/arch-at91/ics1523.h
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/include/asm-arm/arch-at91/ics1523.h
-@@ -0,0 +1,154 @@
-+//*----------------------------------------------------------------------------
-+//* ATMEL Microcontroller Software Support - ROUSSET -
-+//*----------------------------------------------------------------------------
-+//* The software is delivered "AS IS" without warranty or condition of any
-+//* kind, either express, implied or statutory. This includes without
-+//* limitation any warranty or condition with respect to merchantability or
-+//* fitness for any particular purpose, or against the infringements of
-+//* intellectual property rights of others.
-+//*----------------------------------------------------------------------------
-+//* File Name : ics1523.h
-+//* Object : Clock Generator Prototyping File.
-+//*
-+//* 1.0 08/28/02 ED : Creation
-+//* 1.2 13/01/03 FB : Update on lib V3
-+//*----------------------------------------------------------------------------
-+
-+#ifndef ics1523_h
-+#define ics1523_h
-+
-+/*-------------------------------------------*/
-+/* ICS1523 TWI Serial Clock Definition */
-+/*-------------------------------------------*/
-+
-+#define ICS_MIN_CLOCK 100 /* Min Frequency Access Clock KHz */
-+#define ICS_MAX_CLOCK 400 /* Max Frequency Access Clock KHz */
-+#define ICS_TRANSFER_RATE ICS_MAX_CLOCK /* Transfer speed to apply */
-+
-+#define ICS_WRITE_CLK_PNB 30 /* TWCK Clock Periods required to write */
-+#define ICS_READ_CLK_PNB 40 /* TWCK Clock Periods required to read */
-+
-+/*-------------------------------------------*/
-+/* ICS1523 Write Operation Definition */
-+/*-------------------------------------------*/
-+
-+#define ICS1523_ACCESS_OK 0 /* OK */
-+#define ICS1523_ACCESS_ERROR -1 /* NOK */
-+
-+/*-------------------------------------------*/
-+/* ICS1523 Device Addresses Definition */
-+/*-------------------------------------------*/
-+
-+#define ICS_ADDR 0x26 /* Device Address */
-+
-+/*--------------------------------------------------*/
-+/* ICS1523 Registers Internal Addresses Definition */
-+/*--------------------------------------------------*/
-+
-+#define ICS_ICR 0x0 /* Input Control Register */
-+#define ICS_LCR 0x1 /* Loop Control Register */
-+#define ICS_FD0 0x2 /* PLL FeedBack Divider LSBs */
-+#define ICS_FD1 0x3 /* PLL FeedBack Divider MSBs */
-+#define ICS_DPAO 0x4 /* Dynamic Phase Aligner Offset */
-+#define ICS_DPAC 0x5 /* Dynamic Phase Aligner Resolution */
-+#define ICS_OE 0x6 /* Output Enables Register */
-+#define ICS_OD 0x7 /* Osc Divider Register */
-+#define ICS_SWRST 0x8 /* DPA & PLL Reset Register */
-+#define ICS_VID 0x10 /* Chip Version Register */
-+#define ICS_RID 0x11 /* Chip Revision Register */
-+#define ICS_SR 0x12 /* Status Register */
-+
-+/*------------------------------------------------------*/
-+/* ICS1523 Input Control Register Bits Definition */
-+/*------------------------------------------------------*/
-+
-+#define ICS_PDEN 0x1 /* Phase Detector Enable */
-+#define ICS_PDPOL 0x2 /* Phase Detector Enable Polarity */
-+#define ICS_REFPOL 0x4 /* External Reference Polarity */
-+#define ICS_FBKPOL 0x8 /* External Feedback Polarity */
-+#define ICS_FBKSEL 0x10 /* External Feedback Select */
-+#define ICS_FUNCSEL 0x20 /* Function Out Select */
-+#define ICS_ENPLS 0x40 /* Enable PLL Lock/Ref Status Output */
-+#define ICS_ENDLS 0x80 /* Enable DPA Lock/Ref Status Output */
-+
-+/*-----------------------------------------------------*/
-+/* ICS1523 Loop Control Register Bits Definition */
-+/*-----------------------------------------------------*/
-+
-+#define ICS_PFD 0x7 /* Phase Detector Gain */
-+#define ICS_PSD 0x30 /* Post-Scaler Divider */
-+
-+/*----------------------------------------------------*/
-+/* ICS1523 PLL FeedBack Divider LSBs Definition */
-+/*----------------------------------------------------*/
-+
-+#define ICS_FBDL 0xFF /* PLL FeedBack Divider LSBs */
-+
-+/*----------------------------------------------------*/
-+/* ICS1523 PLL FeedBack Divider MSBs Definition */
-+/*----------------------------------------------------*/
-+
-+#define ICS_FBDM 0xF /* PLL FeedBack Divider MSBs */
-+
-+/*------------------------------------------------------------*/
-+/* ICS1523 Dynamic Phase Aligner Offset Bits Definition */
-+/*------------------------------------------------------------*/
-+
-+#define ICS_DPAOS 0x2F /* Dynamic Phase Aligner Offset */
-+#define ICS_FILSEL 0x80 /* Loop Filter Select */
-+
-+/*----------------------------------------------------------------*/
-+/* ICS1523 Dynamic Phase Aligner Resolution Bits Definition */
-+/*----------------------------------------------------------------*/
-+
-+#define ICS_DPARES 0x3 /* Dynamic Phase Aligner Resolution */
-+#define ICS_MMREV 0xFC /* Metal Mask Revision Number */
-+
-+/*-------------------------------------------------------*/
-+/* ICS1523 Output Enables Register Bits Definition */
-+/*-------------------------------------------------------*/
-+
-+#define ICS_OEPCK 0x1 /* Output Enable for PECL PCLK Outputs */
-+#define ICS_OETCK 0x2 /* Output Enable for STTL CLK Output */
-+#define ICS_OEP2 0x4 /* Output Enable for PECL CLK/2 Outputs */
-+#define ICS_OET2 0x8 /* Output Enable for STTL CLK/2 Output */
-+#define ICS_OEF 0x10 /* Output Enable for STTL FUNC Output */
-+#define ICS_CLK2INV 0x20 /* CLK/2 Invert */
-+#define ICS_OSCL 0xC0 /* SSTL Clock Scaler */
-+
-+/*----------------------------------------------------*/
-+/* ICS1523 Osc Divider Register Bits Definition */
-+/*----------------------------------------------------*/
-+
-+#define ICS_OSCDIV 0x7F /* Oscillator Divider Modulus */
-+#define ICS_INSEL 0x80 /* Input Select */
-+
-+/*---------------------------------------------------*/
-+/* ICS1523 DPA & PLL Reset Register Definition */
-+/*---------------------------------------------------*/
-+
-+#define ICS_DPAR 0x0A /* DPA Reset Command */
-+#define ICS_PLLR 0x50 /* PLL Reset Command */
-+
-+/*------------------------------------------------*/
-+/* ICS1523 Chip Version Register Definition */
-+/*------------------------------------------------*/
-+
-+#define ICS_CHIPV 0xFF /* Chip Version */
-+
-+/*-------------------------------------------------*/
-+/* ICS1523 Chip Revision Register Definition */
-+/*-------------------------------------------------*/
-+
-+#define ICS_CHIPR 0xFF /* Chip Revision */
-+
-+/*------------------------------------------*/
-+/* ICS1523 Status Register Definition */
-+/*------------------------------------------*/
-+
-+#define ICS_DPALOCK 0x1 /* DPA Lock Status */
-+#define ICS_PLLLOCK 0x2 /* PLL Lock Status */
-+
-+int at91_ics1523_init(void);
-+
-+#endif /* ics1523_h */
-Index: linux-2.6.22.19/include/asm-arm/arch-at91/spi.h
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/include/asm-arm/arch-at91/spi.h
-@@ -0,0 +1,54 @@
-+/*
-+ * Serial Peripheral Interface (SPI) driver for the Atmel AT91RM9200
-+ *
-+ * (c) SAN People (Pty) Ltd
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * as published by the Free Software Foundation; either version
-+ * 2 of the License, or (at your option) any later version.
-+ */
-+
-+#ifndef AT91_LEGACY_SPI_H
-+#define AT91_LEGACY_SPI_H
-+
-+#define SPI_MAJOR 153 /* registered device number */
-+
-+#define DEFAULT_SPI_CLK 6000000
-+
-+
-+/* Maximum number of buffers in a single SPI transfer.
-+ * DataFlash uses maximum of 2
-+ * spidev interface supports up to 8.
-+ */
-+#define MAX_SPI_TRANSFERS 8
-+#define NR_SPI_DEVICES 4 /* number of devices on SPI bus */
-+
-+/*
-+ * Describes the buffers for a SPI transfer.
-+ * A transmit & receive buffer must be specified for each transfer
-+ */
-+struct spi_transfer_list {
-+ void* tx[MAX_SPI_TRANSFERS]; /* transmit */
-+ int txlen[MAX_SPI_TRANSFERS];
-+ void* rx[MAX_SPI_TRANSFERS]; /* receive */
-+ int rxlen[MAX_SPI_TRANSFERS];
-+ int nr_transfers; /* number of transfers */
-+ int curr; /* current transfer */
-+};
-+
-+struct spi_local {
-+ unsigned int pcs; /* Peripheral Chip Select value */
-+
-+ struct spi_transfer_list *xfers; /* current transfer list */
-+ dma_addr_t tx, rx; /* DMA address for current transfer */
-+ dma_addr_t txnext, rxnext; /* DMA address for next transfer */
-+};
-+
-+
-+/* Exported functions */
-+extern void spi_access_bus(short device);
-+extern void spi_release_bus(short device);
-+extern int spi_transfer(struct spi_transfer_list* list);
-+
-+#endif
-Index: linux-2.6.22.19/include/linux/clk.h
-===================================================================
---- linux-2.6.22.19.orig/include/linux/clk.h
-+++ linux-2.6.22.19/include/linux/clk.h
-@@ -121,4 +121,24 @@ int clk_set_parent(struct clk *clk, stru
- */
- struct clk *clk_get_parent(struct clk *clk);
-
-+/**
-+ * clk_must_disable - report whether a clock's users must disable it
-+ * @clk: one node in the clock tree
-+ *
-+ * This routine returns true only if the upcoming system state requires
-+ * disabling the specified clock.
-+ *
-+ * It's common for platform power states to constrain certain clocks (and
-+ * their descendants) to be unavailable, while other states allow that
-+ * clock to be active. A platform's power states often include an "all on"
-+ * mode; system wide sleep states like "standby" or "suspend-to-RAM"; and
-+ * operating states which sacrifice functionality for lower power usage.
-+ *
-+ * The constraint value is commonly tested in device driver suspend(), to
-+ * leave clocks active if they are needed for features like wakeup events.
-+ * On platforms that support reduced functionality operating states, the
-+ * constraint may also need to be tested during resume() and probe() calls.
-+ */
-+int clk_must_disable(struct clk *clk);
-+
- #endif
-Index: linux-2.6.22.19/include/linux/i2c-id.h
-===================================================================
---- linux-2.6.22.19.orig/include/linux/i2c-id.h
-+++ linux-2.6.22.19/include/linux/i2c-id.h
-@@ -203,6 +203,7 @@
-
- /* --- PCA 9564 based algorithms */
- #define I2C_HW_A_ISA 0x1a0000 /* generic ISA Bus interface card */
-+#define I2C_HW_A_PLAT 0x1a0001 /* generic platform_bus interface */
-
- /* --- ACPI Embedded controller algorithms */
- #define I2C_HW_ACPI_EC 0x1f0000
-Index: linux-2.6.22.19/sound/soc/at91/eti_b1_wm8731.c
-===================================================================
---- linux-2.6.22.19.orig/sound/soc/at91/eti_b1_wm8731.c
-+++ linux-2.6.22.19/sound/soc/at91/eti_b1_wm8731.c
-@@ -34,8 +34,7 @@
- #include <sound/soc.h>
- #include <sound/soc-dapm.h>
-
--#include <asm/arch/hardware.h>
--#include <asm/arch/at91_pio.h>
-+#include <asm/hardware.h>
- #include <asm/arch/gpio.h>
-
- #include "../codecs/wm8731.h"
-@@ -48,13 +47,6 @@
- #define DBG(x...)
- #endif
-
--#define AT91_PIO_TF1 (1 << (AT91_PIN_PB6 - PIN_BASE) % 32)
--#define AT91_PIO_TK1 (1 << (AT91_PIN_PB7 - PIN_BASE) % 32)
--#define AT91_PIO_TD1 (1 << (AT91_PIN_PB8 - PIN_BASE) % 32)
--#define AT91_PIO_RD1 (1 << (AT91_PIN_PB9 - PIN_BASE) % 32)
--#define AT91_PIO_RK1 (1 << (AT91_PIN_PB10 - PIN_BASE) % 32)
--#define AT91_PIO_RF1 (1 << (AT91_PIN_PB11 - PIN_BASE) % 32)
--
- static struct clk *pck1_clk;
- static struct clk *pllb_clk;
-
-@@ -277,7 +269,6 @@ static struct platform_device *eti_b1_sn
- static int __init eti_b1_init(void)
- {
- int ret;
-- u32 ssc_pio_lines;
- struct at91_ssc_periph *ssc = eti_b1_dai.cpu_dai->private_data;
-
- if (!request_mem_region(AT91RM9200_BASE_SSC1, SZ_16K, "soc-audio")) {
-@@ -311,19 +302,12 @@ static int __init eti_b1_init(void)
- goto fail_io_unmap;
- }
-
-- ssc_pio_lines = AT91_PIO_TF1 | AT91_PIO_TK1 | AT91_PIO_TD1
-- | AT91_PIO_RD1 /* | AT91_PIO_RK1 */ | AT91_PIO_RF1;
--
-- /* Reset all PIO registers and assign lines to peripheral A */
-- at91_sys_write(AT91_PIOB + PIO_PDR, ssc_pio_lines);
-- at91_sys_write(AT91_PIOB + PIO_ODR, ssc_pio_lines);
-- at91_sys_write(AT91_PIOB + PIO_IFDR, ssc_pio_lines);
-- at91_sys_write(AT91_PIOB + PIO_CODR, ssc_pio_lines);
-- at91_sys_write(AT91_PIOB + PIO_IDR, ssc_pio_lines);
-- at91_sys_write(AT91_PIOB + PIO_MDDR, ssc_pio_lines);
-- at91_sys_write(AT91_PIOB + PIO_PUDR, ssc_pio_lines);
-- at91_sys_write(AT91_PIOB + PIO_ASR, ssc_pio_lines);
-- at91_sys_write(AT91_PIOB + PIO_OWDR, ssc_pio_lines);
-+ at91_set_A_periph(AT91_PIN_PB6, 0); /* TF1 */
-+ at91_set_A_periph(AT91_PIN_PB7, 0); /* TK1 */
-+ at91_set_A_periph(AT91_PIN_PB8, 0); /* TD1 */
-+ at91_set_A_periph(AT91_PIN_PB9, 0); /* RD1 */
-+/* at91_set_A_periph(AT91_PIN_PB10, 0);*/ /* RK1 */
-+ at91_set_A_periph(AT91_PIN_PB11, 0); /* RF1 */
-
- /*
- * Set PCK1 parent to PLLB and its rate to 12 Mhz.
-Index: linux-2.6.22.19/drivers/char/at91_spi.c
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/drivers/char/at91_spi.c
-@@ -0,0 +1,336 @@
-+/*
-+ * Serial Peripheral Interface (SPI) driver for the Atmel AT91RM9200 (Thunder)
-+ *
-+ * Copyright (C) SAN People (Pty) Ltd
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * as published by the Free Software Foundation; either version
-+ * 2 of the License, or (at your option) any later version.
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/module.h>
-+#include <linux/sched.h>
-+#include <linux/completion.h>
-+#include <linux/interrupt.h>
-+#include <linux/clk.h>
-+#include <linux/platform_device.h>
-+#include <linux/atmel_pdc.h>
-+#include <asm/io.h>
-+#include <asm/semaphore.h>
-+
-+#include <asm/arch/at91_spi.h>
-+#include <asm/arch/board.h>
-+#include <asm/arch/spi.h>
-+
-+#undef DEBUG_SPI
-+
-+static struct spi_local spi_dev[NR_SPI_DEVICES]; /* state of the SPI devices */
-+static int spi_enabled = 0;
-+static struct semaphore spi_lock; /* protect access to SPI bus */
-+static int current_device = -1; /* currently selected SPI device */
-+static struct clk *spi_clk; /* SPI clock */
-+static void __iomem *spi_base; /* SPI peripheral base-address */
-+
-+DECLARE_COMPLETION(transfer_complete);
-+
-+
-+#define at91_spi_read(reg) __raw_readl(spi_base + (reg))
-+#define at91_spi_write(reg, val) __raw_writel((val), spi_base + (reg))
-+
-+
-+/* ......................................................................... */
-+
-+/*
-+ * Access and enable the SPI bus.
-+ * This MUST be called before any transfers are performed.
-+ */
-+void spi_access_bus(short device)
-+{
-+ /* Ensure that requested device is valid */
-+ if ((device < 0) || (device >= NR_SPI_DEVICES))
-+ panic("at91_spi: spi_access_bus called with invalid device");
-+
-+ if (spi_enabled == 0) {
-+ clk_enable(spi_clk); /* Enable Peripheral clock */
-+ at91_spi_write(AT91_SPI_CR, AT91_SPI_SPIEN); /* Enable SPI */
-+#ifdef DEBUG_SPI
-+ printk("SPI on\n");
-+#endif
-+ }
-+ spi_enabled++;
-+
-+ /* Lock the SPI bus */
-+ down(&spi_lock);
-+ current_device = device;
-+
-+ /* Configure SPI bus for device */
-+ at91_spi_write(AT91_SPI_MR, AT91_SPI_MSTR | AT91_SPI_MODFDIS | (spi_dev[device].pcs << 16));
-+}
-+
-+/*
-+ * Relinquish control of the SPI bus.
-+ */
-+void spi_release_bus(short device)
-+{
-+ if (device != current_device)
-+ panic("at91_spi: spi_release called with invalid device");
-+
-+ /* Release the SPI bus */
-+ current_device = -1;
-+ up(&spi_lock);
-+
-+ spi_enabled--;
-+ if (spi_enabled == 0) {
-+ at91_spi_write(AT91_SPI_CR, AT91_SPI_SPIDIS); /* Disable SPI */
-+ clk_disable(spi_clk); /* Disable Peripheral clock */
-+#ifdef DEBUG_SPI
-+ printk("SPI off\n");
-+#endif
-+ }
-+}
-+
-+/*
-+ * Perform a data transfer over the SPI bus
-+ */
-+int spi_transfer(struct spi_transfer_list* list)
-+{
-+ struct spi_local *device = (struct spi_local *) &spi_dev[current_device];
-+ int tx_size;
-+
-+ if (!list)
-+ panic("at91_spi: spi_transfer called with NULL transfer list");
-+ if (current_device == -1)
-+ panic("at91_spi: spi_transfer called without acquiring bus");
-+
-+#ifdef DEBUG_SPI
-+ printk("SPI transfer start [%i]\n", list->nr_transfers);
-+#endif
-+
-+ /* If we are in 16-bit mode, we need to modify what we pass to the PDC */
-+ tx_size = (at91_spi_read(AT91_SPI_CSR(current_device)) & AT91_SPI_BITS_16) ? 2 : 1;
-+
-+ /* Store transfer list */
-+ device->xfers = list;
-+ list->curr = 0;
-+
-+ /* Assume there must be at least one transfer */
-+ device->tx = dma_map_single(NULL, list->tx[0], list->txlen[0], DMA_TO_DEVICE);
-+ device->rx = dma_map_single(NULL, list->rx[0], list->rxlen[0], DMA_FROM_DEVICE);
-+
-+ /* Program PDC registers */
-+ at91_spi_write(ATMEL_PDC_TPR, device->tx);
-+ at91_spi_write(ATMEL_PDC_RPR, device->rx);
-+ at91_spi_write(ATMEL_PDC_TCR, list->txlen[0] / tx_size);
-+ at91_spi_write(ATMEL_PDC_RCR, list->rxlen[0] / tx_size);
-+
-+ /* Is there a second transfer? */
-+ if (list->nr_transfers > 1) {
-+ device->txnext = dma_map_single(NULL, list->tx[1], list->txlen[1], DMA_TO_DEVICE);
-+ device->rxnext = dma_map_single(NULL, list->rx[1], list->rxlen[1], DMA_FROM_DEVICE);
-+
-+ /* Program Next PDC registers */
-+ at91_spi_write(ATMEL_PDC_TNPR, device->txnext);
-+ at91_spi_write(ATMEL_PDC_RNPR, device->rxnext);
-+ at91_spi_write(ATMEL_PDC_TNCR, list->txlen[1] / tx_size);
-+ at91_spi_write(ATMEL_PDC_RNCR, list->rxlen[1] / tx_size);
-+ }
-+ else {
-+ device->txnext = 0;
-+ device->rxnext = 0;
-+ at91_spi_write(ATMEL_PDC_TNCR, 0);
-+ at91_spi_write(ATMEL_PDC_RNCR, 0);
-+ }
-+
-+ // TODO: If we are doing consecutive transfers (at high speed, or
-+ // small buffers), then it might be worth modifying the 'Delay between
-+ // Consecutive Transfers' in the CSR registers.
-+ // This is an issue if we cannot chain the next buffer fast enough
-+ // in the interrupt handler.
-+
-+ /* Enable transmitter and receiver */
-+ at91_spi_write(ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN | ATMEL_PDC_TXTEN);
-+
-+ at91_spi_write(AT91_SPI_IER, AT91_SPI_ENDRX); /* enable buffer complete interrupt */
-+ wait_for_completion(&transfer_complete);
-+
-+#ifdef DEBUG_SPI
-+ printk("SPI transfer end\n");
-+#endif
-+
-+ return 0;
-+}
-+
-+/* ......................................................................... */
-+
-+/*
-+ * Handle interrupts from the SPI controller.
-+ */
-+static irqreturn_t at91spi_interrupt(int irq, void *dev_id)
-+{
-+ unsigned int status;
-+ struct spi_local *device = (struct spi_local *) &spi_dev[current_device];
-+ struct spi_transfer_list *list = device->xfers;
-+
-+#ifdef DEBUG_SPI
-+ printk("SPI interrupt %i\n", current_device);
-+#endif
-+
-+ if (!list)
-+ panic("at91_spi: spi_interrupt with a NULL transfer list");
-+
-+ status = at91_spi_read(AT91_SPI_SR) & at91_spi_read(AT91_SPI_IMR); /* read status */
-+
-+ dma_unmap_single(NULL, device->tx, list->txlen[list->curr], DMA_TO_DEVICE);
-+ dma_unmap_single(NULL, device->rx, list->rxlen[list->curr], DMA_FROM_DEVICE);
-+
-+ device->tx = device->txnext; /* move next transfer to current transfer */
-+ device->rx = device->rxnext;
-+
-+ list->curr = list->curr + 1;
-+ if (list->curr == list->nr_transfers) { /* all transfers complete */
-+ at91_spi_write(AT91_SPI_IDR, AT91_SPI_ENDRX); /* disable interrupt */
-+
-+ /* Disable transmitter and receiver */
-+ at91_spi_write(ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
-+
-+ device->xfers = NULL;
-+ complete(&transfer_complete);
-+ }
-+ else if (list->curr+1 == list->nr_transfers) { /* no more next transfers */
-+ device->txnext = 0;
-+ device->rxnext = 0;
-+ at91_spi_write(ATMEL_PDC_TNCR, 0);
-+ at91_spi_write(ATMEL_PDC_RNCR, 0);
-+ }
-+ else {
-+ int i = (list->curr)+1;
-+
-+ /* If we are in 16-bit mode, we need to modify what we pass to the PDC */
-+ int tx_size = (at91_spi_read(AT91_SPI_CSR(current_device)) & AT91_SPI_BITS_16) ? 2 : 1;
-+
-+ device->txnext = dma_map_single(NULL, list->tx[i], list->txlen[i], DMA_TO_DEVICE);
-+ device->rxnext = dma_map_single(NULL, list->rx[i], list->rxlen[i], DMA_FROM_DEVICE);
-+ at91_spi_write(ATMEL_PDC_TNPR, device->txnext);
-+ at91_spi_write(ATMEL_PDC_RNPR, device->rxnext);
-+ at91_spi_write(ATMEL_PDC_TNCR, list->txlen[i] / tx_size);
-+ at91_spi_write(ATMEL_PDC_RNCR, list->rxlen[i] / tx_size);
-+ }
-+ return IRQ_HANDLED;
-+}
-+
-+/* ......................................................................... */
-+
-+/*
-+ * Initialize the SPI controller
-+ */
-+static int __init at91spi_probe(struct platform_device *pdev)
-+{
-+ int i;
-+ unsigned long scbr;
-+ struct resource *res;
-+
-+ init_MUTEX(&spi_lock);
-+
-+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ if (!res)
-+ return -ENXIO;
-+
-+ if (!request_mem_region(res->start, res->end - res->start + 1, "at91_spi"))
-+ return -EBUSY;
-+
-+ spi_base = ioremap(res->start, res->end - res->start + 1);
-+ if (!spi_base) {
-+ release_mem_region(res->start, res->end - res->start + 1);
-+ return -ENOMEM;
-+ }
-+
-+ spi_clk = clk_get(NULL, "spi_clk");
-+ if (IS_ERR(spi_clk)) {
-+ printk(KERN_ERR "at91_spi: no clock defined\n");
-+ iounmap(spi_base);
-+ release_mem_region(res->start, res->end - res->start + 1);
-+ return -ENODEV;
-+ }
-+
-+ at91_spi_write(AT91_SPI_CR, AT91_SPI_SWRST); /* software reset of SPI controller */
-+
-+ /*
-+ * Calculate the correct SPI baud-rate divisor.
-+ */
-+ scbr = clk_get_rate(spi_clk) / (2 * DEFAULT_SPI_CLK);
-+ scbr = scbr + 1; /* round up */
-+
-+ printk(KERN_INFO "at91_spi: Baud rate set to %ld\n", clk_get_rate(spi_clk) / (2 * scbr));
-+
-+ /* Set Chip Select registers to good defaults */
-+ for (i = 0; i < 4; i++) {
-+ at91_spi_write(AT91_SPI_CSR(i), AT91_SPI_CPOL | AT91_SPI_BITS_8 | (16 << 16) | (scbr << 8));
-+ }
-+
-+ at91_spi_write(ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
-+
-+ memset(&spi_dev, 0, sizeof(spi_dev));
-+ spi_dev[0].pcs = 0xE;
-+ spi_dev[1].pcs = 0xD;
-+ spi_dev[2].pcs = 0xB;
-+ spi_dev[3].pcs = 0x7;
-+
-+ if (request_irq(AT91RM9200_ID_SPI, at91spi_interrupt, 0, "spi", NULL)) {
-+ clk_put(spi_clk);
-+ iounmap(spi_base);
-+ release_mem_region(res->start, res->end - res->start + 1);
-+ return -EBUSY;
-+ }
-+
-+ at91_spi_write(AT91_SPI_CR, AT91_SPI_SPIEN); /* Enable SPI */
-+
-+ return 0;
-+}
-+
-+static int __devexit at91spi_remove(struct platform_device *pdev)
-+{
-+ struct resource *res;
-+
-+ at91_spi_write(AT91_SPI_CR, AT91_SPI_SPIDIS); /* Disable SPI */
-+ clk_put(spi_clk);
-+
-+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ iounmap(spi_base);
-+ release_mem_region(res->start, res->end - res->start + 1);
-+
-+ free_irq(AT91RM9200_ID_SPI, 0);
-+ return 0;
-+}
-+
-+static struct platform_driver at91spi_driver = {
-+ .probe = at91spi_probe,
-+ .remove = __devexit_p(at91spi_remove),
-+ .driver = {
-+ .name = "at91_spi",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+static int __init at91spi_init(void)
-+{
-+ return platform_driver_register(&at91spi_driver);
-+}
-+
-+static void __exit at91spi_exit(void)
-+{
-+ platform_driver_unregister(&at91spi_driver);
-+}
-+
-+EXPORT_SYMBOL(spi_access_bus);
-+EXPORT_SYMBOL(spi_release_bus);
-+EXPORT_SYMBOL(spi_transfer);
-+
-+module_init(at91spi_init);
-+module_exit(at91spi_exit);
-+
-+MODULE_LICENSE("GPL")
-+MODULE_AUTHOR("Andrew Victor")
-+MODULE_DESCRIPTION("SPI driver for Atmel AT91RM9200")
-Index: linux-2.6.22.19/drivers/char/at91_spidev.c
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/drivers/char/at91_spidev.c
-@@ -0,0 +1,236 @@
-+/*
-+ * User-space interface to the SPI bus on Atmel AT91RM9200
-+ *
-+ * Copyright (C) 2003 SAN People (Pty) Ltd
-+ *
-+ * Based on SPI driver by Rick Bronson
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * as published by the Free Software Foundation; either version
-+ * 2 of the License, or (at your option) any later version.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/init.h>
-+#include <linux/slab.h>
-+#include <linux/highmem.h>
-+#include <linux/pagemap.h>
-+#include <asm/arch/spi.h>
-+
-+#ifdef CONFIG_DEVFS_FS
-+#include <linux/devfs_fs_kernel.h>
-+#endif
-+
-+
-+#undef DEBUG_SPIDEV
-+
-+/* ......................................................................... */
-+
-+/*
-+ * Read or Write to SPI bus.
-+ */
-+static ssize_t spidev_rd_wr(struct file *file, char *buf, size_t count, loff_t *offset)
-+{
-+ unsigned int spi_device = (unsigned int) file->private_data;
-+
-+ struct mm_struct * mm;
-+ struct page ** maplist;
-+ struct spi_transfer_list* list;
-+ int pgcount;
-+
-+ unsigned int ofs, pagelen;
-+ int res, i, err;
-+
-+ if (!count) {
-+ return 0;
-+ }
-+
-+ list = kmalloc(sizeof(struct spi_transfer_list), GFP_KERNEL);
-+ if (!list) {
-+ return -ENOMEM;
-+ }
-+
-+ mm = current->mm;
-+
-+ pgcount = ((unsigned long)buf+count+PAGE_SIZE-1)/PAGE_SIZE - (unsigned long)buf/PAGE_SIZE;
-+
-+ if (pgcount >= MAX_SPI_TRANSFERS) {
-+ kfree(list);
-+ return -EFBIG;
-+ }
-+
-+ maplist = kmalloc (pgcount * sizeof (struct page *), GFP_KERNEL);
-+
-+ if (!maplist) {
-+ kfree(list);
-+ return -ENOMEM;
-+ }
-+ flush_cache_all();
-+ down_read(&mm->mmap_sem);
-+ err= get_user_pages(current, mm, (unsigned long)buf, pgcount, 1, 0, maplist, NULL);
-+ up_read(&mm->mmap_sem);
-+
-+ if (err < 0) {
-+ kfree(list);
-+ kfree(maplist);
-+ return err;
-+ }
-+ pgcount = err;
-+
-+#ifdef DEBUG_SPIDEV
-+ printk("spidev_rd_rw: %i %i\n", count, pgcount);
-+#endif
-+
-+ /* Set default return value = transfer length */
-+ res = count;
-+
-+ /*
-+ * At this point, the virtual area buf[0] .. buf[count-1] will have
-+ * corresponding pages mapped in the physical memory and locked until
-+ * we unmap the kiobuf. The pages cannot be swapped out or moved
-+ * around.
-+ */
-+ ofs = (unsigned long) buf & (PAGE_SIZE -1);
-+ pagelen = PAGE_SIZE - ofs;
-+ if (count < pagelen)
-+ pagelen = count;
-+
-+ for (i = 0; i < pgcount; i++) {
-+ flush_dcache_page(maplist[i]);
-+
-+ list->tx[i] = list->rx[i] = page_address(maplist[i]) + ofs;
-+ list->txlen[i] = list->rxlen[i] = pagelen;
-+
-+#ifdef DEBUG_SPIDEV
-+ printk(" %i: %x (%i)\n", i, list->tx[i], list->txlen[i]);
-+#endif
-+
-+ ofs = 0; /* all subsequent transfers start at beginning of a page */
-+ count = count - pagelen;
-+ pagelen = (count < PAGE_SIZE) ? count : PAGE_SIZE;
-+ }
-+ list->nr_transfers = pgcount;
-+
-+ /* Perform transfer on SPI bus */
-+ spi_access_bus(spi_device);
-+ spi_transfer(list);
-+ spi_release_bus(spi_device);
-+
-+ while (pgcount--) {
-+ page_cache_release (maplist[pgcount]);
-+ }
-+ flush_cache_all();
-+
-+ kfree(maplist);
-+ kfree(list);
-+
-+ return res;
-+}
-+
-+static int spidev_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg)
-+{
-+ int spi_device = MINOR(inode->i_rdev);
-+
-+ if (spi_device >= NR_SPI_DEVICES)
-+ return -ENODEV;
-+
-+ // TODO: This interface can be used to configure the SPI bus.
-+ // Configurable options could include: Speed, Clock Polarity, Clock Phase
-+
-+ switch(cmd) {
-+ default:
-+ return -ENOIOCTLCMD;
-+ }
-+}
-+
-+/*
-+ * Open the SPI device
-+ */
-+static int spidev_open(struct inode *inode, struct file *file)
-+{
-+ unsigned int spi_device = MINOR(inode->i_rdev);
-+
-+ if (spi_device >= NR_SPI_DEVICES)
-+ return -ENODEV;
-+
-+ /*
-+ * 'private_data' is actually a pointer, but we overload it with the
-+ * value we want to store.
-+ */
-+ file->private_data = (void *)spi_device;
-+
-+ return 0;
-+}
-+
-+/*
-+ * Close the SPI device
-+ */
-+static int spidev_close(struct inode *inode, struct file *file)
-+{
-+ return 0;
-+}
-+
-+/* ......................................................................... */
-+
-+static struct file_operations spidev_fops = {
-+ .owner = THIS_MODULE,
-+ .llseek = no_llseek,
-+ .read = spidev_rd_wr,
-+ .write = (int (*) (struct file *file, const char *buf, size_t count, loff_t *offset))spidev_rd_wr,
-+ .ioctl = spidev_ioctl,
-+ .open = spidev_open,
-+ .release = spidev_close,
-+};
-+
-+/*
-+ * Install the SPI /dev interface driver
-+ */
-+static int __init at91_spidev_init(void)
-+{
-+#ifdef CONFIG_DEVFS_FS
-+ int i;
-+#endif
-+
-+ if (register_chrdev(SPI_MAJOR, "spi", &spidev_fops)) {
-+ printk(KERN_ERR "at91_spidev: Unable to get major %d for SPI bus\n", SPI_MAJOR);
-+ return -EIO;
-+ }
-+
-+#ifdef CONFIG_DEVFS_FS
-+ devfs_mk_dir("spi");
-+ for (i = 0; i < NR_SPI_DEVICES; i++) {
-+ devfs_mk_cdev(MKDEV(SPI_MAJOR, i), S_IFCHR | S_IRUSR | S_IWUSR, "spi/%d",i);
-+ }
-+#endif
-+ printk(KERN_INFO "AT91 SPI driver loaded\n");
-+
-+ return 0;
-+}
-+
-+/*
-+ * Remove the SPI /dev interface driver
-+ */
-+static void __exit at91_spidev_exit(void)
-+{
-+#ifdef CONFIG_DEVFS_FS
-+ int i;
-+ for (i = 0; i < NR_SPI_DEVICES; i++) {
-+ devfs_remove("spi/%d", i);
-+ }
-+
-+ devfs_remove("spi");
-+#endif
-+
-+ if (unregister_chrdev(SPI_MAJOR, "spi")) {
-+ printk(KERN_ERR "at91_spidev: Unable to release major %d for SPI bus\n", SPI_MAJOR);
-+ return;
-+ }
-+}
-+
-+module_init(at91_spidev_init);
-+module_exit(at91_spidev_exit);
-+
-+MODULE_LICENSE("GPL")
-+MODULE_AUTHOR("Andrew Victor")
-+MODULE_DESCRIPTION("SPI /dev interface for Atmel AT91RM9200")
-Index: linux-2.6.22.19/drivers/char/Kconfig
-===================================================================
---- linux-2.6.22.19.orig/drivers/char/Kconfig
-+++ linux-2.6.22.19/drivers/char/Kconfig
-@@ -1083,5 +1083,21 @@ config DEVPORT
-
- source "drivers/s390/char/Kconfig"
-
-+config AT91_SPI
-+ bool "SPI driver (legacy) for AT91RM9200 processors"
-+ depends on ARCH_AT91RM9200
-+ default y
-+ help
-+ The SPI driver gives access to this serial bus on the AT91RM9200
-+ processor.
-+
-+config AT91_SPIDEV
-+ bool "SPI device interface (legacy) for AT91RM9200 processors"
-+ depends on ARCH_AT91RM9200 && AT91_SPI
-+ default n
-+ help
-+ The SPI driver gives user mode access to this serial
-+ bus on the AT91RM9200 processor.
-+
- endmenu
-
-Index: linux-2.6.22.19/drivers/char/Makefile
-===================================================================
---- linux-2.6.22.19.orig/drivers/char/Makefile
-+++ linux-2.6.22.19/drivers/char/Makefile
-@@ -93,6 +93,8 @@ obj-$(CONFIG_CS5535_GPIO) += cs5535_gpio
- obj-$(CONFIG_GPIO_VR41XX) += vr41xx_giu.o
- obj-$(CONFIG_GPIO_TB0219) += tb0219.o
- obj-$(CONFIG_TELCLOCK) += tlclk.o
-+obj-$(CONFIG_AT91_SPI) += at91_spi.o
-+obj-$(CONFIG_AT91_SPIDEV) += at91_spidev.o
-
- obj-$(CONFIG_WATCHDOG) += watchdog/
- obj-$(CONFIG_MWAVE) += mwave/
-Index: linux-2.6.22.19/drivers/i2c/busses/i2c-at91.c
-===================================================================
---- linux-2.6.22.19.orig/drivers/i2c/busses/i2c-at91.c
-+++ linux-2.6.22.19/drivers/i2c/busses/i2c-at91.c
-@@ -31,8 +31,11 @@
- #include <asm/arch/board.h>
- #include <asm/arch/cpu.h>
-
--#define TWI_CLOCK 100000 /* Hz. max 400 Kbits/sec */
-
-+/* Clockrate is configurable - max 400 Kbits/sec */
-+static unsigned int clockrate = CONFIG_I2C_AT91_CLOCKRATE;
-+module_param(clockrate, uint, 0);
-+MODULE_PARM_DESC(clockrate, "The TWI clockrate");
-
- static struct clk *twi_clk;
- static void __iomem *twi_base;
-@@ -53,7 +56,7 @@ static void __devinit at91_twi_hwinit(vo
- at91_twi_write(AT91_TWI_CR, AT91_TWI_MSEN); /* Set Master mode */
-
- /* Calcuate clock dividers */
-- cdiv = (clk_get_rate(twi_clk) / (2 * TWI_CLOCK)) - 3;
-+ cdiv = (clk_get_rate(twi_clk) / (2 * clockrate)) - 3;
- cdiv = cdiv + 1; /* round up */
- ckdiv = 0;
- while (cdiv > 255) {
-@@ -61,11 +64,12 @@ static void __devinit at91_twi_hwinit(vo
- cdiv = cdiv >> 1;
- }
-
-- if (cpu_is_at91rm9200()) { /* AT91RM9200 Errata #22 */
-- if (ckdiv > 5) {
-- printk(KERN_ERR "AT91 I2C: Invalid TWI_CLOCK value!\n");
-- ckdiv = 5;
-- }
-+ if (cpu_is_at91rm9200() && (ckdiv > 5)) { /* AT91RM9200 Errata #22 */
-+ printk(KERN_ERR "AT91 I2C: Invalid TWI clockrate!\n");
-+ ckdiv = 5;
-+ } else if (ckdiv > 7) {
-+ printk(KERN_ERR "AT91 I2C: Invalid TWI clockrate!\n");
-+ ckdiv = 7;
- }
-
- at91_twi_write(AT91_TWI_CWGR, (ckdiv << 16) | (cdiv << 8) | cdiv);
-Index: linux-2.6.22.19/drivers/i2c/busses/i2c-pca.c
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/drivers/i2c/busses/i2c-pca.c
-@@ -0,0 +1,213 @@
-+/*
-+ * Platform driver for PCA9564 I2C bus controller.
-+ *
-+ * (C) 2006 Andrew Victor
-+ *
-+ * Based on i2c-pca-isa.c driver for PCA9564 on ISA boards
-+ * Copyright (C) 2004 Arcom Control Systems
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/moduleparam.h>
-+#include <linux/delay.h>
-+#include <linux/init.h>
-+#include <linux/interrupt.h>
-+#include <linux/wait.h>
-+#include <linux/platform_device.h>
-+
-+#include <linux/i2c.h>
-+#include <linux/i2c-algo-pca.h>
-+
-+#include <asm/io.h>
-+
-+#include "../algos/i2c-algo-pca.h"
-+
-+#define PCA_OWN_ADDRESS 0x55 /* our address for slave mode */
-+#define PCA_CLOCK I2C_PCA_CON_59kHz
-+
-+//#define REG_SHIFT 2
-+#define REG_SHIFT 0
-+
-+//#define DEBUG_IO
-+
-+#define PCA_IO_SIZE 4
-+
-+static void __iomem *base_addr;
-+static int irq;
-+static wait_queue_head_t pca_wait;
-+
-+static int pca_getown(struct i2c_algo_pca_data *adap)
-+{
-+ return PCA_OWN_ADDRESS;
-+}
-+
-+static int pca_getclock(struct i2c_algo_pca_data *adap)
-+{
-+ return PCA_CLOCK;
-+}
-+
-+static void pca_writebyte(struct i2c_algo_pca_data *adap, int reg, int val)
-+{
-+#ifdef DEBUG_IO
-+ static char *names[] = { "T/O", "DAT", "ADR", "CON" };
-+ printk("*** write %s at %#lx <= %#04x\n", names[reg], (unsigned long) base_addr+reg, val);
-+#endif
-+ udelay(1);
-+ outb(val, base_addr + (reg << REG_SHIFT));
-+}
-+
-+static int pca_readbyte(struct i2c_algo_pca_data *adap, int reg)
-+{
-+ int res;
-+
-+ udelay(1);
-+ res = inb(base_addr + (reg << REG_SHIFT));
-+#ifdef DEBUG_IO
-+ {
-+ static char *names[] = { "STA", "DAT", "ADR", "CON" };
-+ printk("*** read %s => %#04x\n", names[reg], res);
-+ }
-+#endif
-+ return res;
-+}
-+
-+static int pca_waitforinterrupt(struct i2c_algo_pca_data *adap)
-+{
-+ int ret = 0;
-+
-+ if (irq > -1) {
-+ ret = wait_event_interruptible(pca_wait,
-+ pca_readbyte(adap, I2C_PCA_CON) & I2C_PCA_CON_SI);
-+ } else {
-+ while ((pca_readbyte(adap, I2C_PCA_CON) & I2C_PCA_CON_SI) == 0)
-+ udelay(100);
-+ }
-+ return ret;
-+}
-+
-+static irqreturn_t pca_handler(int this_irq, void *dev_id)
-+{
-+ wake_up_interruptible(&pca_wait);
-+ return IRQ_HANDLED;
-+}
-+
-+static struct i2c_algo_pca_data pca_i2c_data = {
-+ .get_own = pca_getown,
-+ .get_clock = pca_getclock,
-+ .write_byte = pca_writebyte,
-+ .read_byte = pca_readbyte,
-+ .wait_for_interrupt = pca_waitforinterrupt,
-+};
-+
-+static struct i2c_adapter pca_i2c_ops = {
-+ .owner = THIS_MODULE,
-+ .id = I2C_HW_A_PLAT,
-+ .algo_data = &pca_i2c_data,
-+ .name = "PCA9564",
-+ .class = I2C_CLASS_HWMON,
-+};
-+
-+static int __devinit pca_i2c_probe(struct platform_device *pdev)
-+{
-+ struct resource *res;
-+
-+ init_waitqueue_head(&pca_wait);
-+
-+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ if (!res)
-+ return -ENODEV;
-+
-+ if (!request_mem_region(res->start, PCA_IO_SIZE, "PCA9564"))
-+ return -ENXIO;
-+
-+ base_addr = ioremap(res->start, PCA_IO_SIZE);
-+ if (base_addr == NULL)
-+ goto out_region;
-+
-+ irq = platform_get_irq(pdev, 0);
-+ if (irq > -1) {
-+ if (request_irq(irq, pca_handler, 0, "pca9564", NULL) < 0) {
-+ printk(KERN_ERR "i2c-pca: Request irq%d failed\n", irq);
-+ goto out_remap;
-+ }
-+ }
-+
-+ /* set up the driverfs linkage to our parent device */
-+ pca_i2c_ops.dev.parent = &pdev->dev;
-+
-+ if (i2c_pca_add_bus(&pca_i2c_ops) < 0) {
-+ printk(KERN_ERR "i2c-pca: Failed to add i2c bus\n");
-+ goto out_irq;
-+ }
-+
-+ return 0;
-+
-+ out_irq:
-+ if (irq > -1)
-+ free_irq(irq, &pca_i2c_ops);
-+
-+ out_remap:
-+ iounmap(base_addr);
-+
-+ out_region:
-+ release_mem_region(res->start, PCA_IO_SIZE);
-+ return -ENODEV;
-+}
-+
-+static int __devexit pca_i2c_remove(struct platform_device *pdev)
-+{
-+ struct resource *res;
-+
-+ i2c_del_adapter(&pca_i2c_ops);
-+
-+ if (irq > 0)
-+ free_irq(irq, NULL);
-+
-+ iounmap(base_addr);
-+
-+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ release_mem_region(res->start, PCA_IO_SIZE);
-+
-+ return 0;
-+}
-+
-+static struct platform_driver pca_i2c_driver = {
-+ .probe = pca_i2c_probe,
-+ .remove = __devexit_p(pca_i2c_remove),
-+ .driver = {
-+ .name = "pca9564",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+static int __init pca_i2c_init(void)
-+{
-+ return platform_driver_register(&pca_i2c_driver);
-+}
-+
-+static void __exit pca_i2c_exit(void)
-+{
-+ platform_driver_unregister(&pca_i2c_driver);
-+}
-+
-+module_init(pca_i2c_init);
-+module_exit(pca_i2c_exit);
-+
-+MODULE_AUTHOR("Andrew Victor");
-+MODULE_DESCRIPTION("PCA9564 platform driver");
-+MODULE_LICENSE("GPL");
-Index: linux-2.6.22.19/drivers/i2c/busses/Kconfig
-===================================================================
---- linux-2.6.22.19.orig/drivers/i2c/busses/Kconfig
-+++ linux-2.6.22.19/drivers/i2c/busses/Kconfig
-@@ -80,6 +80,14 @@ config I2C_AT91
- This supports the use of the I2C interface on Atmel AT91
- processors.
-
-+config I2C_AT91_CLOCKRATE
-+ prompt "Atmel AT91 I2C/TWI clock-rate"
-+ depends on I2C_AT91
-+ int
-+ default 100000
-+ help
-+ Set the AT91 I2C/TWI clock-rate.
-+
- config I2C_AU1550
- tristate "Au1550/Au1200 SMBus interface"
- depends on SOC_AU1550 || SOC_AU1200
-@@ -598,6 +606,14 @@ config I2C_VOODOO3
- This driver can also be built as a module. If so, the module
- will be called i2c-voodoo3.
-
-+config I2C_PCA
-+ tristate "PCA9564"
-+ depends on I2C
-+ select I2C_ALGOPCA
-+ help
-+ This driver support the Philips PCA 9564 Parallel bus to I2C
-+ bus controller.
-+
- config I2C_PCA_ISA
- tristate "PCA9564 on an ISA bus"
- depends on ISA
-Index: linux-2.6.22.19/drivers/i2c/busses/Makefile
-===================================================================
---- linux-2.6.22.19.orig/drivers/i2c/busses/Makefile
-+++ linux-2.6.22.19/drivers/i2c/busses/Makefile
-@@ -30,6 +30,7 @@ obj-$(CONFIG_I2C_OMAP) += i2c-omap.o
- obj-$(CONFIG_I2C_PARPORT) += i2c-parport.o
- obj-$(CONFIG_I2C_PARPORT_LIGHT) += i2c-parport-light.o
- obj-$(CONFIG_I2C_PASEMI) += i2c-pasemi.o
-+obj-$(CONFIG_I2C_PCA) += i2c-pca.o
- obj-$(CONFIG_I2C_PCA_ISA) += i2c-pca-isa.o
- obj-$(CONFIG_I2C_PIIX4) += i2c-piix4.o
- obj-$(CONFIG_I2C_PNX) += i2c-pnx.o
-Index: linux-2.6.22.19/drivers/leds/Kconfig
-===================================================================
---- linux-2.6.22.19.orig/drivers/leds/Kconfig
-+++ linux-2.6.22.19/drivers/leds/Kconfig
-@@ -77,6 +77,13 @@ config LEDS_NET48XX
- This option enables support for the Soekris net4801 and net4826 error
- LED.
-
-+config LEDS_AT91
-+ tristate "LED support using AT91 GPIOs"
-+ depends on LEDS_CLASS && ARCH_AT91 && !LEDS
-+ help
-+ This option enables support for LEDs connected to GPIO lines
-+ on AT91-based boards.
-+
- config LEDS_WRAP
- tristate "LED Support for the WRAP series LEDs"
- depends on LEDS_CLASS && SCx200_GPIO
-Index: linux-2.6.22.19/drivers/leds/leds-at91.c
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/drivers/leds/leds-at91.c
-@@ -0,0 +1,140 @@
-+/*
-+ * AT91 GPIO based LED driver
-+ *
-+ * Copyright (C) 2006 David Brownell
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/platform_device.h>
-+#include <linux/leds.h>
-+
-+#include <asm/arch/board.h>
-+#include <asm/arch/gpio.h>
-+
-+static LIST_HEAD(at91_led_list); /* list of AT91 LEDs */
-+
-+struct at91_led {
-+ struct led_classdev cdev;
-+ struct list_head list;
-+ struct at91_gpio_led *led_data;
-+};
-+
-+/*
-+ * Change the state of the LED.
-+ */
-+static void at91_led_set(struct led_classdev *cdev, enum led_brightness value)
-+{
-+ struct at91_led *led = container_of(cdev, struct at91_led, cdev);
-+ short active = (value == LED_OFF);
-+
-+ if (led->led_data->flags & 1) /* active high/low? */
-+ active = !active;
-+ at91_set_gpio_value(led->led_data->gpio, active);
-+}
-+
-+static int __devexit at91_led_remove(struct platform_device *pdev)
-+{
-+ struct at91_led *led;
-+
-+ list_for_each_entry (led, &at91_led_list, list)
-+ led_classdev_unregister(&led->cdev);
-+
-+#warning "Free allocated memory"
-+ // TODO: Free memory. kfree(led);
-+
-+ return 0;
-+}
-+
-+static int __init at91_led_probe(struct platform_device *pdev)
-+{
-+ int status = 0;
-+ struct at91_gpio_led *pdata = pdev->dev.platform_data;
-+ unsigned nr_leds;
-+ struct at91_led *led;
-+
-+ if (!pdata)
-+ return -ENODEV;
-+
-+ nr_leds = pdata->index; /* first index stores number of LEDs */
-+
-+ while (nr_leds--) {
-+ led = kzalloc(sizeof(struct at91_led), GFP_KERNEL);
-+ if (!led) {
-+ dev_err(&pdev->dev, "No memory for device\n");
-+ status = -ENOMEM;
-+ goto cleanup;
-+ }
-+ led->led_data = pdata;
-+ led->cdev.name = pdata->name;
-+ led->cdev.brightness_set = at91_led_set,
-+ led->cdev.default_trigger = pdata->trigger;
-+
-+ status = led_classdev_register(&pdev->dev, &led->cdev);
-+ if (status < 0) {
-+ dev_err(&pdev->dev, "led_classdev_register failed - %d\n", status);
-+cleanup:
-+ at91_led_remove(pdev);
-+ break;
-+ }
-+ list_add(&led->list, &at91_led_list);
-+ pdata++;
-+ }
-+ return status;
-+}
-+
-+#ifdef CONFIG_PM
-+static int at91_led_suspend(struct platform_device *dev, pm_message_t state)
-+{
-+ struct at91_led *led;
-+
-+ list_for_each_entry (led, &at91_led_list, list)
-+ led_classdev_suspend(&led->cdev);
-+
-+ return 0;
-+}
-+
-+static int at91_led_resume(struct platform_device *dev)
-+{
-+ struct at91_led *led;
-+
-+ list_for_each_entry (led, &at91_led_list, list)
-+ led_classdev_resume(&led->cdev);
-+
-+ return 0;
-+}
-+#else
-+#define at91_led_suspend NULL
-+#define at91_led_resume NULL
-+#endif
-+
-+static struct platform_driver at91_led_driver = {
-+ .probe = at91_led_probe,
-+ .remove = __devexit_p(at91_led_remove),
-+ .suspend = at91_led_suspend,
-+ .resume = at91_led_resume,
-+ .driver = {
-+ .name = "at91_leds",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+static int __init at91_led_init(void)
-+{
-+ return platform_driver_register(&at91_led_driver);
-+}
-+module_init(at91_led_init);
-+
-+static void __exit at91_led_exit(void)
-+{
-+ platform_driver_unregister(&at91_led_driver);
-+}
-+module_exit(at91_led_exit);
-+
-+MODULE_DESCRIPTION("AT91 GPIO LED driver");
-+MODULE_AUTHOR("David Brownell");
-+MODULE_LICENSE("GPL");
-Index: linux-2.6.22.19/drivers/leds/Makefile
-===================================================================
---- linux-2.6.22.19.orig/drivers/leds/Makefile
-+++ linux-2.6.22.19/drivers/leds/Makefile
-@@ -16,6 +16,7 @@ obj-$(CONFIG_LEDS_NET48XX) += leds-net4
- obj-$(CONFIG_LEDS_WRAP) += leds-wrap.o
- obj-$(CONFIG_LEDS_H1940) += leds-h1940.o
- obj-$(CONFIG_LEDS_COBALT) += leds-cobalt.o
-+obj-$(CONFIG_LEDS_AT91) += leds-at91.o
-
- # LED Triggers
- obj-$(CONFIG_LEDS_TRIGGER_TIMER) += ledtrig-timer.o
-Index: linux-2.6.22.19/drivers/mmc/host/at91_mci.c
-===================================================================
---- linux-2.6.22.19.orig/drivers/mmc/host/at91_mci.c
-+++ linux-2.6.22.19/drivers/mmc/host/at91_mci.c
-@@ -85,7 +85,7 @@
-
- #define AT91_MCI_ERRORS (AT91_MCI_RINDE | AT91_MCI_RDIRE | AT91_MCI_RCRCE \
- | AT91_MCI_RENDE | AT91_MCI_RTOE | AT91_MCI_DCRCE \
-- | AT91_MCI_DTOE | AT91_MCI_OVRE | AT91_MCI_UNRE)
-+ | AT91_MCI_DTOE | AT91_MCI_OVRE | AT91_MCI_UNRE)
-
- #define at91_mci_read(host, reg) __raw_readl((host)->baseaddr + (reg))
- #define at91_mci_write(host, reg, val) __raw_writel((val), (host)->baseaddr + (reg))
-@@ -560,9 +560,7 @@ static void at91mci_completed_command(st
- pr_debug("Status = %08X [%08X %08X %08X %08X]\n",
- status, cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3]);
-
-- if (status & (AT91_MCI_RINDE | AT91_MCI_RDIRE | AT91_MCI_RCRCE |
-- AT91_MCI_RENDE | AT91_MCI_RTOE | AT91_MCI_DCRCE |
-- AT91_MCI_DTOE | AT91_MCI_OVRE | AT91_MCI_UNRE)) {
-+ if (status & AT91_MCI_ERRORS) {
- if ((status & AT91_MCI_RCRCE) && !(mmc_resp_type(cmd) & MMC_RSP_CRC)) {
- cmd->error = MMC_ERR_NONE;
- }
-@@ -663,15 +661,15 @@ static irqreturn_t at91_mci_irq(int irq,
-
- int_status = at91_mci_read(host, AT91_MCI_SR);
- int_mask = at91_mci_read(host, AT91_MCI_IMR);
--
-+
- pr_debug("MCI irq: status = %08X, %08X, %08X\n", int_status, int_mask,
- int_status & int_mask);
--
-+
- int_status = int_status & int_mask;
-
- if (int_status & AT91_MCI_ERRORS) {
- completed = 1;
--
-+
- if (int_status & AT91_MCI_UNRE)
- pr_debug("MMC: Underrun error\n");
- if (int_status & AT91_MCI_OVRE)
-@@ -819,7 +817,7 @@ static int __init at91_mci_probe(struct
- mmc->f_min = 375000;
- mmc->f_max = 25000000;
- mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
-- mmc->caps = MMC_CAP_BYTEBLOCK;
-+ mmc->caps = MMC_CAP_BYTEBLOCK | MMC_CAP_MULTIWRITE;
-
- mmc->max_blk_size = 4095;
- mmc->max_blk_count = mmc->max_req_size;
-@@ -893,6 +891,8 @@ static int __init at91_mci_probe(struct
-
- mmc_add_host(mmc);
-
-+ device_init_wakeup(&pdev->dev, 1);
-+
- /*
- * monitor card insertion/removal if we can
- */
-@@ -922,6 +922,8 @@ static int __exit at91_mci_remove(struct
-
- host = mmc_priv(mmc);
-
-+ device_init_wakeup(&pdev->dev, 0);
-+
- if (host->present != -1) {
- free_irq(host->board->det_pin, host);
- cancel_delayed_work(&host->mmc->detect);
-@@ -949,8 +951,12 @@ static int __exit at91_mci_remove(struct
- static int at91_mci_suspend(struct platform_device *pdev, pm_message_t state)
- {
- struct mmc_host *mmc = platform_get_drvdata(pdev);
-+ struct at91mci_host *host = mmc_priv(mmc);
- int ret = 0;
-
-+ if (device_may_wakeup(&pdev->dev))
-+ enable_irq_wake(host->board->det_pin);
-+
- if (mmc)
- ret = mmc_suspend_host(mmc, state);
-
-@@ -960,8 +966,12 @@ static int at91_mci_suspend(struct platf
- static int at91_mci_resume(struct platform_device *pdev)
- {
- struct mmc_host *mmc = platform_get_drvdata(pdev);
-+ struct at91mci_host *host = mmc_priv(mmc);
- int ret = 0;
-
-+ if (device_may_wakeup(&pdev->dev))
-+ disable_irq_wake(host->board->det_pin);
-+
- if (mmc)
- ret = mmc_resume_host(mmc);
-
-Index: linux-2.6.22.19/drivers/mtd/devices/at91_dataflash.c
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/drivers/mtd/devices/at91_dataflash.c
-@@ -0,0 +1,667 @@
-+/*
-+ * Atmel DataFlash driver for Atmel AT91RM9200 (Thunder)
-+ *
-+ * Copyright (C) SAN People (Pty) Ltd
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * as published by the Free Software Foundation; either version
-+ * 2 of the License, or (at your option) any later version.
-+*/
-+
-+#include <linux/module.h>
-+#include <linux/init.h>
-+#include <linux/slab.h>
-+#include <linux/pci.h>
-+#include <linux/mtd/mtd.h>
-+#include <linux/mtd/partitions.h>
-+
-+#include <asm/arch/spi.h>
-+
-+#undef DEBUG_DATAFLASH
-+
-+#define DATAFLASH_MAX_DEVICES 4 /* max number of dataflash devices */
-+#undef DATAFLASH_ALWAYS_ADD_DEVICE /* always add whole device when using partitions? */
-+
-+#define OP_READ_CONTINUOUS 0xE8
-+#define OP_READ_PAGE 0xD2
-+#define OP_READ_BUFFER1 0xD4
-+#define OP_READ_BUFFER2 0xD6
-+#define OP_READ_STATUS 0xD7
-+
-+#define OP_ERASE_PAGE 0x81
-+#define OP_ERASE_BLOCK 0x50
-+
-+#define OP_TRANSFER_BUF1 0x53
-+#define OP_TRANSFER_BUF2 0x55
-+#define OP_COMPARE_BUF1 0x60
-+#define OP_COMPARE_BUF2 0x61
-+
-+#define OP_PROGRAM_VIA_BUF1 0x82
-+#define OP_PROGRAM_VIA_BUF2 0x85
-+
-+struct dataflash_local
-+{
-+ int spi; /* SPI chip-select number */
-+
-+ unsigned int page_size; /* number of bytes per page */
-+ unsigned short page_offset; /* page offset in flash address */
-+};
-+
-+
-+/* Detected DataFlash devices */
-+static struct mtd_info* mtd_devices[DATAFLASH_MAX_DEVICES];
-+static int nr_devices = 0;
-+
-+/* ......................................................................... */
-+
-+#ifdef CONFIG_MTD_PARTITIONS
-+
-+static struct mtd_partition static_partitions_2M[] =
-+{
-+ {
-+ .name = "bootloader",
-+ .offset = 0,
-+ .size = 1 * 32 * 8 * 528, /* 1st sector = 32 blocks * 8 pages * 528 bytes */
-+ .mask_flags = MTD_WRITEABLE, /* read-only */
-+ },
-+ {
-+ .name = "kernel",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = 6 * 32 * 8 * 528, /* 6 sectors */
-+ },
-+ {
-+ .name = "filesystem",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = MTDPART_SIZ_FULL, /* rest = 9 sectors */
-+ }
-+};
-+
-+static struct mtd_partition static_partitions_4M[] =
-+{
-+ {
-+ .name = "bootloader",
-+ .offset = 0,
-+ .size = 1 * 64 * 8 * 528, /* 1st sector = 64 blocks * 8 pages * 528 bytes */
-+ .mask_flags = MTD_WRITEABLE, /* read-only */
-+ },
-+ {
-+ .name = "kernel",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = 4 * 64 * 8 * 528, /* 4 sectors */
-+ },
-+ {
-+ .name = "filesystem",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = MTDPART_SIZ_FULL, /* rest = 11 sectors */
-+ }
-+};
-+
-+#if defined(CONFIG_MACH_KAFA)
-+static struct mtd_partition static_partitions_8M[] =
-+{
-+ {
-+ name: "romboot",
-+ offset: 0,
-+ size: 16 * 1056, /* 160 Kb */
-+ mask_flags: MTD_WRITEABLE, /* read-only */
-+ },
-+ {
-+ name: "uboot",
-+ offset: MTDPART_OFS_APPEND, /* Sperry, NXTBLK is broken */
-+ size: 128 * 1056, /* 1 MB */
-+ },
-+ {
-+ name: "kernel",
-+ offset: MTDPART_OFS_APPEND, /* Sperry, NXTBLK is broken */
-+ size: 1024 * 1056, /* 1 MB */
-+ },
-+ {
-+ name: "filesystem",
-+ offset: MTDPART_OFS_APPEND, /* Sperry, NXTBLK is broken */
-+ size: MTDPART_SIZ_FULL,
-+ }
-+};
-+
-+#elif defined(CONFIG_MACH_MULTMDP)
-+
-+static struct mtd_partition static_partitions_8M[] =
-+{
-+ {
-+ .name = "bootloader",
-+ .offset = 0,
-+ .size = 12 * 1056, /* 1st sector = 32 blocks * 8 pages * 1056 bytes */
-+ .mask_flags = MTD_WRITEABLE, /* read-only */
-+ },
-+ {
-+ .name = "configuration",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = 20 * 1056,
-+ },
-+ {
-+ .name = "kernel",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = 1520 * 1056,
-+ },
-+ {
-+ .name = "filesystem",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = MTDPART_SIZ_FULL,
-+ }
-+};
-+
-+#else
-+
-+static struct mtd_partition static_partitions_8M[] =
-+{
-+ {
-+ .name = "bootloader",
-+ .offset = 0,
-+ .size = 1 * 32 * 8 * 1056, /* 1st sector = 32 blocks * 8 pages * 1056 bytes */
-+ .mask_flags = MTD_WRITEABLE, /* read-only */
-+ },
-+ {
-+ .name = "kernel",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = 5 * 32 * 8 * 1056, /* 5 sectors */
-+ },
-+ {
-+ .name = "filesystem",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = MTDPART_SIZ_FULL, /* rest = 26 sectors */
-+ }
-+};
-+#endif
-+
-+static const char *part_probes[] = { "cmdlinepart", NULL, };
-+
-+#endif
-+
-+/* ......................................................................... */
-+
-+/* Allocate a single SPI transfer descriptor. We're assuming that if multiple
-+ SPI transfers occur at the same time, spi_access_bus() will serialize them.
-+ If this is not valid, then either (i) each dataflash 'priv' structure
-+ needs it's own transfer descriptor, (ii) we lock this one, or (iii) use
-+ another mechanism. */
-+static struct spi_transfer_list* spi_transfer_desc;
-+
-+/*
-+ * Perform a SPI transfer to access the DataFlash device.
-+ */
-+static int do_spi_transfer(int nr, char* tx, int tx_len, char* rx, int rx_len,
-+ char* txnext, int txnext_len, char* rxnext, int rxnext_len)
-+{
-+ struct spi_transfer_list* list = spi_transfer_desc;
-+
-+ list->tx[0] = tx; list->txlen[0] = tx_len;
-+ list->rx[0] = rx; list->rxlen[0] = rx_len;
-+
-+ list->tx[1] = txnext; list->txlen[1] = txnext_len;
-+ list->rx[1] = rxnext; list->rxlen[1] = rxnext_len;
-+
-+ list->nr_transfers = nr;
-+
-+ return spi_transfer(list);
-+}
-+
-+/* ......................................................................... */
-+
-+/*
-+ * Poll the DataFlash device until it is READY.
-+ */
-+static void at91_dataflash_waitready(void)
-+{
-+ char* command = kmalloc(2, GFP_KERNEL);
-+
-+ if (!command)
-+ return;
-+
-+ do {
-+ command[0] = OP_READ_STATUS;
-+ command[1] = 0;
-+
-+ do_spi_transfer(1, command, 2, command, 2, NULL, 0, NULL, 0);
-+ } while ((command[1] & 0x80) == 0);
-+
-+ kfree(command);
-+}
-+
-+/*
-+ * Return the status of the DataFlash device.
-+ */
-+static unsigned short at91_dataflash_status(void)
-+{
-+ unsigned short status;
-+ char* command = kmalloc(2, GFP_KERNEL);
-+
-+ if (!command)
-+ return 0;
-+
-+ command[0] = OP_READ_STATUS;
-+ command[1] = 0;
-+
-+ do_spi_transfer(1, command, 2, command, 2, NULL, 0, NULL, 0);
-+ status = command[1];
-+
-+ kfree(command);
-+ return status;
-+}
-+
-+/* ......................................................................... */
-+
-+/*
-+ * Erase blocks of flash.
-+ */
-+static int at91_dataflash_erase(struct mtd_info *mtd, struct erase_info *instr)
-+{
-+ struct dataflash_local *priv = (struct dataflash_local *) mtd->priv;
-+ unsigned int pageaddr;
-+ char* command;
-+
-+#ifdef DEBUG_DATAFLASH
-+ printk("dataflash_erase: addr=%i len=%i\n", instr->addr, instr->len);
-+#endif
-+
-+ /* Sanity checks */
-+ if (instr->addr + instr->len > mtd->size)
-+ return -EINVAL;
-+ if ((instr->len % mtd->erasesize != 0) || (instr->len % priv->page_size != 0))
-+ return -EINVAL;
-+ if ((instr->addr % priv->page_size) != 0)
-+ return -EINVAL;
-+
-+ command = kmalloc(4, GFP_KERNEL);
-+ if (!command)
-+ return -ENOMEM;
-+
-+ while (instr->len > 0) {
-+ /* Calculate flash page address */
-+ pageaddr = (instr->addr / priv->page_size) << priv->page_offset;
-+
-+ command[0] = OP_ERASE_PAGE;
-+ command[1] = (pageaddr & 0x00FF0000) >> 16;
-+ command[2] = (pageaddr & 0x0000FF00) >> 8;
-+ command[3] = 0;
-+#ifdef DEBUG_DATAFLASH
-+ printk("ERASE: (%x) %x %x %x [%i]\n", command[0], command[1], command[2], command[3], pageaddr);
-+#endif
-+
-+ /* Send command to SPI device */
-+ spi_access_bus(priv->spi);
-+ do_spi_transfer(1, command, 4, command, 4, NULL, 0, NULL, 0);
-+
-+ at91_dataflash_waitready(); /* poll status until ready */
-+ spi_release_bus(priv->spi);
-+
-+ instr->addr += priv->page_size; /* next page */
-+ instr->len -= priv->page_size;
-+ }
-+
-+ kfree(command);
-+
-+ /* Inform MTD subsystem that erase is complete */
-+ instr->state = MTD_ERASE_DONE;
-+ if (instr->callback)
-+ instr->callback(instr);
-+
-+ return 0;
-+}
-+
-+/*
-+ * Read from the DataFlash device.
-+ * from : Start offset in flash device
-+ * len : Amount to read
-+ * retlen : About of data actually read
-+ * buf : Buffer containing the data
-+ */
-+static int at91_dataflash_read(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, u_char *buf)
-+{
-+ struct dataflash_local *priv = (struct dataflash_local *) mtd->priv;
-+ unsigned int addr;
-+ char* command;
-+
-+#ifdef DEBUG_DATAFLASH
-+ printk("dataflash_read: %lli .. %lli\n", from, from+len);
-+#endif
-+
-+ *retlen = 0;
-+
-+ /* Sanity checks */
-+ if (!len)
-+ return 0;
-+ if (from + len > mtd->size)
-+ return -EINVAL;
-+
-+ /* Calculate flash page/byte address */
-+ addr = (((unsigned)from / priv->page_size) << priv->page_offset) + ((unsigned)from % priv->page_size);
-+
-+ command = kmalloc(8, GFP_KERNEL);
-+ if (!command)
-+ return -ENOMEM;
-+
-+ command[0] = OP_READ_CONTINUOUS;
-+ command[1] = (addr & 0x00FF0000) >> 16;
-+ command[2] = (addr & 0x0000FF00) >> 8;
-+ command[3] = (addr & 0x000000FF);
-+#ifdef DEBUG_DATAFLASH
-+ printk("READ: (%x) %x %x %x\n", command[0], command[1], command[2], command[3]);
-+#endif
-+
-+ /* Send command to SPI device */
-+ spi_access_bus(priv->spi);
-+ do_spi_transfer(2, command, 8, command, 8, buf, len, buf, len);
-+ spi_release_bus(priv->spi);
-+
-+ *retlen = len;
-+ kfree(command);
-+ return 0;
-+}
-+
-+/*
-+ * Write to the DataFlash device.
-+ * to : Start offset in flash device
-+ * len : Amount to write
-+ * retlen : Amount of data actually written
-+ * buf : Buffer containing the data
-+ */
-+static int at91_dataflash_write(struct mtd_info *mtd, loff_t to, size_t len, size_t *retlen, const u_char *buf)
-+{
-+ struct dataflash_local *priv = (struct dataflash_local *) mtd->priv;
-+ unsigned int pageaddr, addr, offset, writelen;
-+ size_t remaining;
-+ u_char *writebuf;
-+ unsigned short status;
-+ int res = 0;
-+ char* command;
-+ char* tmpbuf = NULL;
-+
-+#ifdef DEBUG_DATAFLASH
-+ printk("dataflash_write: %lli .. %lli\n", to, to+len);
-+#endif
-+
-+ *retlen = 0;
-+
-+ /* Sanity checks */
-+ if (!len)
-+ return 0;
-+ if (to + len > mtd->size)
-+ return -EINVAL;
-+
-+ command = kmalloc(4, GFP_KERNEL);
-+ if (!command)
-+ return -ENOMEM;
-+
-+ pageaddr = ((unsigned)to / priv->page_size);
-+ offset = ((unsigned)to % priv->page_size);
-+ if (offset + len > priv->page_size)
-+ writelen = priv->page_size - offset;
-+ else
-+ writelen = len;
-+ writebuf = (u_char *)buf;
-+ remaining = len;
-+
-+ /* Allocate temporary buffer */
-+ tmpbuf = kmalloc(priv->page_size, GFP_KERNEL);
-+ if (!tmpbuf) {
-+ kfree(command);
-+ return -ENOMEM;
-+ }
-+
-+ /* Gain access to the SPI bus */
-+ spi_access_bus(priv->spi);
-+
-+ while (remaining > 0) {
-+#ifdef DEBUG_DATAFLASH
-+ printk("write @ %i:%i len=%i\n", pageaddr, offset, writelen);
-+#endif
-+
-+ /* (1) Transfer to Buffer1 */
-+ if (writelen != priv->page_size) {
-+ addr = pageaddr << priv->page_offset;
-+ command[0] = OP_TRANSFER_BUF1;
-+ command[1] = (addr & 0x00FF0000) >> 16;
-+ command[2] = (addr & 0x0000FF00) >> 8;
-+ command[3] = 0;
-+#ifdef DEBUG_DATAFLASH
-+ printk("TRANSFER: (%x) %x %x %x\n", command[0], command[1], command[2], command[3]);
-+#endif
-+ do_spi_transfer(1, command, 4, command, 4, NULL, 0, NULL, 0);
-+ at91_dataflash_waitready();
-+ }
-+
-+ /* (2) Program via Buffer1 */
-+ addr = (pageaddr << priv->page_offset) + offset;
-+ command[0] = OP_PROGRAM_VIA_BUF1;
-+ command[1] = (addr & 0x00FF0000) >> 16;
-+ command[2] = (addr & 0x0000FF00) >> 8;
-+ command[3] = (addr & 0x000000FF);
-+#ifdef DEBUG_DATAFLASH
-+ printk("PROGRAM: (%x) %x %x %x\n", command[0], command[1], command[2], command[3]);
-+#endif
-+ do_spi_transfer(2, command, 4, command, 4, writebuf, writelen, tmpbuf, writelen);
-+ at91_dataflash_waitready();
-+
-+ /* (3) Compare to Buffer1 */
-+ addr = pageaddr << priv->page_offset;
-+ command[0] = OP_COMPARE_BUF1;
-+ command[1] = (addr & 0x00FF0000) >> 16;
-+ command[2] = (addr & 0x0000FF00) >> 8;
-+ command[3] = 0;
-+#ifdef DEBUG_DATAFLASH
-+ printk("COMPARE: (%x) %x %x %x\n", command[0], command[1], command[2], command[3]);
-+#endif
-+ do_spi_transfer(1, command, 4, command, 4, NULL, 0, NULL, 0);
-+ at91_dataflash_waitready();
-+
-+ /* Get result of the compare operation */
-+ status = at91_dataflash_status();
-+ if ((status & 0x40) == 1) {
-+ printk("at91_dataflash: Write error on page %i\n", pageaddr);
-+ remaining = 0;
-+ res = -EIO;
-+ }
-+
-+ remaining = remaining - writelen;
-+ pageaddr++;
-+ offset = 0;
-+ writebuf += writelen;
-+ *retlen += writelen;
-+
-+ if (remaining > priv->page_size)
-+ writelen = priv->page_size;
-+ else
-+ writelen = remaining;
-+ }
-+
-+ /* Release SPI bus */
-+ spi_release_bus(priv->spi);
-+
-+ kfree(tmpbuf);
-+ kfree(command);
-+ return res;
-+}
-+
-+/* ......................................................................... */
-+
-+/*
-+ * Initialize and register DataFlash device with MTD subsystem.
-+ */
-+static int __init add_dataflash(int channel, char *name, int IDsize,
-+ int nr_pages, int pagesize, int pageoffset)
-+{
-+ struct mtd_info *device;
-+ struct dataflash_local *priv;
-+#ifdef CONFIG_MTD_PARTITIONS
-+ struct mtd_partition *mtd_parts = 0;
-+ int mtd_parts_nr = 0;
-+#endif
-+
-+ if (nr_devices >= DATAFLASH_MAX_DEVICES) {
-+ printk(KERN_ERR "at91_dataflash: Too many devices detected\n");
-+ return 0;
-+ }
-+
-+ device = kmalloc(sizeof(struct mtd_info) + strlen(name) + 8, GFP_KERNEL);
-+ if (!device)
-+ return -ENOMEM;
-+ memset(device, 0, sizeof(struct mtd_info));
-+
-+ device->name = (char *)&device[1];
-+ sprintf(device->name, "%s.spi%d", name, channel);
-+ device->size = nr_pages * pagesize;
-+ device->erasesize = pagesize;
-+ device->writesize = pagesize;
-+ device->owner = THIS_MODULE;
-+ device->type = MTD_DATAFLASH;
-+ device->flags = MTD_WRITEABLE;
-+ device->erase = at91_dataflash_erase;
-+ device->read = at91_dataflash_read;
-+ device->write = at91_dataflash_write;
-+
-+ priv = (struct dataflash_local *) kmalloc(sizeof(struct dataflash_local), GFP_KERNEL);
-+ if (!priv) {
-+ kfree(device);
-+ return -ENOMEM;
-+ }
-+ memset(priv, 0, sizeof(struct dataflash_local));
-+
-+ priv->spi = channel;
-+ priv->page_size = pagesize;
-+ priv->page_offset = pageoffset;
-+ device->priv = priv;
-+
-+ mtd_devices[nr_devices] = device;
-+ nr_devices++;
-+ printk("at91_dataflash: %s detected [spi%i] (%i bytes)\n", name, channel, device->size);
-+
-+#ifdef CONFIG_MTD_PARTITIONS
-+#ifdef CONFIG_MTD_CMDLINE_PARTS
-+ mtd_parts_nr = parse_mtd_partitions(device, part_probes, &mtd_parts, 0);
-+#endif
-+ if (mtd_parts_nr <= 0) {
-+ switch (IDsize) {
-+ case SZ_2M:
-+ mtd_parts = static_partitions_2M;
-+ mtd_parts_nr = ARRAY_SIZE(static_partitions_2M);
-+ break;
-+ case SZ_4M:
-+ mtd_parts = static_partitions_4M;
-+ mtd_parts_nr = ARRAY_SIZE(static_partitions_4M);
-+ break;
-+ case SZ_8M:
-+ mtd_parts = static_partitions_8M;
-+ mtd_parts_nr = ARRAY_SIZE(static_partitions_8M);
-+ break;
-+ }
-+ }
-+
-+ if (mtd_parts_nr > 0) {
-+#ifdef DATAFLASH_ALWAYS_ADD_DEVICE
-+ add_mtd_device(device);
-+#endif
-+ return add_mtd_partitions(device, mtd_parts, mtd_parts_nr);
-+ }
-+#endif
-+ return add_mtd_device(device); /* add whole device */
-+}
-+
-+/*
-+ * Detect and initialize DataFlash device connected to specified SPI channel.
-+ *
-+ * Device Density ID code Nr Pages Page Size Page offset
-+ * AT45DB011B 1Mbit (128K) xx0011xx (0x0c) 512 264 9
-+ * AT45DB021B 2Mbit (256K) xx0101xx (0x14) 1025 264 9
-+ * AT45DB041B 4Mbit (512K) xx0111xx (0x1c) 2048 264 9
-+ * AT45DB081B 8Mbit (1M) xx1001xx (0x24) 4096 264 9
-+ * AT45DB0161B 16Mbit (2M) xx1011xx (0x2c) 4096 528 10
-+ * AT45DB0321B 32Mbit (4M) xx1101xx (0x34) 8192 528 10
-+ * AT45DB0642 64Mbit (8M) xx1111xx (0x3c) 8192 1056 11
-+ * AT45DB1282 128Mbit (16M) xx0100xx (0x10) 16384 1056 11
-+ */
-+static int __init at91_dataflash_detect(int channel)
-+{
-+ int res = 0;
-+ unsigned short status;
-+
-+ spi_access_bus(channel);
-+ status = at91_dataflash_status();
-+ spi_release_bus(channel);
-+ if (status != 0xff) { /* no dataflash device there */
-+ switch (status & 0x3c) {
-+ case 0x0c: /* 0 0 1 1 */
-+ res = add_dataflash(channel, "AT45DB011B", SZ_128K, 512, 264, 9);
-+ break;
-+ case 0x14: /* 0 1 0 1 */
-+ res = add_dataflash(channel, "AT45DB021B", SZ_256K, 1025, 264, 9);
-+ break;
-+ case 0x1c: /* 0 1 1 1 */
-+ res = add_dataflash(channel, "AT45DB041B", SZ_512K, 2048, 264, 9);
-+ break;
-+ case 0x24: /* 1 0 0 1 */
-+ res = add_dataflash(channel, "AT45DB081B", SZ_1M, 4096, 264, 9);
-+ break;
-+ case 0x2c: /* 1 0 1 1 */
-+ res = add_dataflash(channel, "AT45DB161B", SZ_2M, 4096, 528, 10);
-+ break;
-+ case 0x34: /* 1 1 0 1 */
-+ res = add_dataflash(channel, "AT45DB321B", SZ_4M, 8192, 528, 10);
-+ break;
-+ case 0x3c: /* 1 1 1 1 */
-+ res = add_dataflash(channel, "AT45DB642", SZ_8M, 8192, 1056, 11);
-+ break;
-+// Currently unsupported since Atmel removed the "Main Memory Program via Buffer" commands.
-+// case 0x10: /* 0 1 0 0 */
-+// res = add_dataflash(channel, "AT45DB1282", SZ_16M, 16384, 1056, 11);
-+// break;
-+ default:
-+ printk(KERN_ERR "at91_dataflash: Unknown device (%x)\n", status & 0x3c);
-+ }
-+ }
-+
-+ return res;
-+}
-+
-+static int __init at91_dataflash_init(void)
-+{
-+ spi_transfer_desc = kmalloc(sizeof(struct spi_transfer_list), GFP_KERNEL);
-+ if (!spi_transfer_desc)
-+ return -ENOMEM;
-+
-+ /* DataFlash (SPI chip select 0) */
-+ at91_dataflash_detect(0);
-+
-+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
-+ /* DataFlash card (SPI chip select 3) */
-+ at91_dataflash_detect(3);
-+#endif
-+
-+ return 0;
-+}
-+
-+static void __exit at91_dataflash_exit(void)
-+{
-+ int i;
-+
-+ for (i = 0; i < DATAFLASH_MAX_DEVICES; i++) {
-+ if (mtd_devices[i]) {
-+#ifdef CONFIG_MTD_PARTITIONS
-+ del_mtd_partitions(mtd_devices[i]);
-+#else
-+ del_mtd_device(mtd_devices[i]);
-+#endif
-+ kfree(mtd_devices[i]->priv);
-+ kfree(mtd_devices[i]);
-+ }
-+ }
-+ nr_devices = 0;
-+ kfree(spi_transfer_desc);
-+}
-+
-+
-+module_init(at91_dataflash_init);
-+module_exit(at91_dataflash_exit);
-+
-+MODULE_LICENSE("GPL");
-+MODULE_AUTHOR("Andrew Victor");
-+MODULE_DESCRIPTION("DataFlash driver for Atmel AT91RM9200");
-Index: linux-2.6.22.19/drivers/mtd/devices/Kconfig
-===================================================================
---- linux-2.6.22.19.orig/drivers/mtd/devices/Kconfig
-+++ linux-2.6.22.19/drivers/mtd/devices/Kconfig
-@@ -269,5 +269,11 @@ config MTD_DOCPROBE_55AA
- LinuxBIOS or if you need to recover a DiskOnChip Millennium on which
- you have managed to wipe the first block.
-
--endmenu
-+config MTD_AT91_DATAFLASH
-+ tristate "AT91RM9200 DataFlash AT45DBxxx (legacy driver)"
-+ depends on MTD && ARCH_AT91RM9200 && AT91_SPI
-+ help
-+ This enables access to the DataFlash (AT45DBxxx) on the AT91RM9200.
-+ If you have such a board, say 'Y'.
-
-+endmenu
-Index: linux-2.6.22.19/drivers/mtd/devices/Makefile
-===================================================================
---- linux-2.6.22.19.orig/drivers/mtd/devices/Makefile
-+++ linux-2.6.22.19/drivers/mtd/devices/Makefile
-@@ -18,3 +18,4 @@ obj-$(CONFIG_MTD_BLOCK2MTD) += block2mtd
- obj-$(CONFIG_MTD_DATAFLASH) += mtd_dataflash.o
- obj-$(CONFIG_MTD_DATAFLASH26) += at91_dataflash26.o
- obj-$(CONFIG_MTD_M25P80) += m25p80.o
-+obj-$(CONFIG_MTD_AT91_DATAFLASH)+= at91_dataflash.o
-Index: linux-2.6.22.19/drivers/net/arm/at91_ether.c
-===================================================================
---- linux-2.6.22.19.orig/drivers/net/arm/at91_ether.c
-+++ linux-2.6.22.19/drivers/net/arm/at91_ether.c
-@@ -894,6 +894,7 @@ static void at91ether_rx(struct net_devi
- skb_reserve(skb, 2);
- memcpy(skb_put(skb, pktlen), p_recv, pktlen);
-
-+ skb->dev = dev;
- skb->protocol = eth_type_trans(skb, dev);
- dev->last_rx = jiffies;
- lp->stats.rx_bytes += pktlen;
-@@ -978,14 +979,22 @@ static int __init at91ether_setup(unsign
- struct net_device *dev;
- struct at91_private *lp;
- unsigned int val;
-- int res;
-+ struct resource *res;
-+ int ret;
-
- dev = alloc_etherdev(sizeof(struct at91_private));
- if (!dev)
- return -ENOMEM;
-
-- dev->base_addr = AT91_VA_BASE_EMAC;
-- dev->irq = AT91RM9200_ID_EMAC;
-+ /* Get I/O base address and IRQ */
-+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ if (!res) {
-+ free_netdev(dev);
-+ return -ENODEV;
-+ }
-+ dev->base_addr = res->start;
-+ dev->irq = platform_get_irq(pdev, 0);
-+
- SET_MODULE_OWNER(dev);
-
- /* Install the interrupt handler */
-@@ -1058,12 +1067,12 @@ static int __init at91ether_setup(unsign
- lp->phy_address = phy_address; /* MDI address of PHY */
-
- /* Register the network interface */
-- res = register_netdev(dev);
-- if (res) {
-+ ret = register_netdev(dev);
-+ if (ret) {
- free_irq(dev->irq, dev);
- free_netdev(dev);
- dma_free_coherent(NULL, sizeof(struct recv_desc_bufs), lp->dlist, (dma_addr_t)lp->dlist_phys);
-- return res;
-+ return ret;
- }
-
- /* Determine current link speed */
-Index: linux-2.6.22.19/drivers/serial/atmel_serial.c
-===================================================================
---- linux-2.6.22.19.orig/drivers/serial/atmel_serial.c
-+++ linux-2.6.22.19/drivers/serial/atmel_serial.c
-@@ -7,6 +7,8 @@
- * Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd.
- * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
- *
-+ * DMA support added by Chip Coldwell.
-+ *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
-@@ -33,6 +35,7 @@
- #include <linux/sysrq.h>
- #include <linux/tty_flip.h>
- #include <linux/platform_device.h>
-+#include <linux/dma-mapping.h>
- #include <linux/atmel_pdc.h>
-
- #include <asm/io.h>
-@@ -47,6 +50,11 @@
-
- #include "atmel_serial.h"
-
-+#define SUPPORT_PDC
-+#define PDC_BUFFER_SIZE (L1_CACHE_BYTES << 3)
-+#warning "Revisit"
-+#define PDC_RX_TIMEOUT (3 * 10) /* 3 bytes */
-+
- #if defined(CONFIG_SERIAL_ATMEL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
- #define SUPPORT_SYSRQ
- #endif
-@@ -107,6 +115,13 @@
- static int (*atmel_open_hook)(struct uart_port *);
- static void (*atmel_close_hook)(struct uart_port *);
-
-+struct atmel_dma_buffer {
-+ unsigned char *buf;
-+ dma_addr_t dma_addr;
-+ size_t dma_size;
-+ unsigned int ofs;
-+};
-+
- /*
- * We wrap our port structure around the generic uart_port.
- */
-@@ -114,10 +129,20 @@ struct atmel_uart_port {
- struct uart_port uart; /* uart */
- struct clk *clk; /* uart clock */
- unsigned short suspended; /* is port suspended? */
-+
-+ short use_dma_rx; /* enable PDC receiver */
-+ short pdc_rx_idx; /* current PDC RX buffer */
-+ struct atmel_dma_buffer pdc_rx[2]; /* PDC receier */
-+
-+ short use_dma_tx; /* enable PDC transmitter */
-+ struct atmel_dma_buffer pdc_tx; /* PDC transmitter */
- };
-
- static struct atmel_uart_port atmel_ports[ATMEL_MAX_UART];
-
-+#define PDC_RX_BUF(port) &(port)->pdc_rx[(port)->pdc_rx_idx]
-+#define PDC_RX_SWITCH(port) (port)->pdc_rx_idx = !(port)->pdc_rx_idx
-+
- #ifdef SUPPORT_SYSRQ
- static struct console atmel_console;
- #endif
-@@ -205,7 +230,12 @@ static void atmel_stop_tx(struct uart_po
- {
- struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
-
-- UART_PUT_IDR(port, ATMEL_US_TXRDY);
-+ if (atmel_port->use_dma_tx) {
-+ UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS); /* disable PDC transmit */
-+ UART_PUT_IDR(port, ATMEL_US_ENDTX | ATMEL_US_TXBUFE);
-+ }
-+ else
-+ UART_PUT_IDR(port, ATMEL_US_TXRDY);
- }
-
- /*
-@@ -215,7 +245,17 @@ static void atmel_start_tx(struct uart_p
- {
- struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
-
-- UART_PUT_IER(port, ATMEL_US_TXRDY);
-+ if (atmel_port->use_dma_tx) {
-+ if (UART_GET_PTSR(port) & ATMEL_PDC_TXTEN)
-+ /* The transmitter is already running. Yes, we
-+ really need this.*/
-+ return;
-+
-+ UART_PUT_IER(port, ATMEL_US_ENDTX | ATMEL_US_TXBUFE);
-+ UART_PUT_PTCR(port, ATMEL_PDC_TXTEN); /* re-enable PDC transmit */
-+ }
-+ else
-+ UART_PUT_IER(port, ATMEL_US_TXRDY);
- }
-
- /*
-@@ -225,7 +265,12 @@ static void atmel_stop_rx(struct uart_po
- {
- struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
-
-- UART_PUT_IDR(port, ATMEL_US_RXRDY);
-+ if (atmel_port->use_dma_rx) {
-+ UART_PUT_PTCR(port, ATMEL_PDC_RXTDIS); /* disable PDC receive */
-+ UART_PUT_IDR(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
-+ }
-+ else
-+ UART_PUT_IDR(port, ATMEL_US_RXRDY);
- }
-
- /*
-@@ -248,6 +293,134 @@ static void atmel_break_ctl(struct uart_
- }
-
- /*
-+ * Receive data via the PDC. A buffer has been fulled.
-+ */
-+static void atmel_pdc_endrx(struct uart_port *port)
-+{
-+ struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
-+ struct tty_struct *tty = port->info->tty;
-+ struct atmel_dma_buffer *pdc = PDC_RX_BUF(atmel_port);
-+ unsigned int count;
-+
-+ count = pdc->dma_size - pdc->ofs;
-+ if (likely(count > 0)) {
-+ dma_sync_single_for_cpu(port->dev, pdc->dma_addr, pdc->dma_size, DMA_FROM_DEVICE);
-+ tty_insert_flip_string(tty, pdc->buf + pdc->ofs, count);
-+ tty_flip_buffer_push(tty);
-+
-+ port->icount.rx += count;
-+ }
-+
-+ /* Set this buffer as the next receive buffer */
-+ pdc->ofs = 0;
-+ UART_PUT_RNPR(port, pdc->dma_addr);
-+ UART_PUT_RNCR(port, pdc->dma_size);
-+
-+ /* Switch to next buffer */
-+ PDC_RX_SWITCH(atmel_port); /* next PDC buffer */
-+}
-+
-+/*
-+ * Receive data via the PDC. At least one byte was received, but the
-+ * buffer was not full when the inter-character timeout expired.
-+ */
-+static void atmel_pdc_timeout(struct uart_port *port)
-+{
-+ struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
-+ struct tty_struct *tty = port->info->tty;
-+ struct atmel_dma_buffer *pdc = PDC_RX_BUF(atmel_port);
-+ /* unsigned */ int ofs, count;
-+
-+ ofs = UART_GET_RPR(port) - pdc->dma_addr; /* current DMA adress */
-+ count = ofs - pdc->ofs;
-+
-+ if (likely(count > 0)) {
-+ dma_sync_single_for_cpu(port->dev, pdc->dma_addr, pdc->dma_size, DMA_FROM_DEVICE);
-+ tty_insert_flip_string(tty, pdc->buf + pdc->ofs, count);
-+ tty_flip_buffer_push(tty);
-+
-+ pdc->ofs = ofs;
-+ port->icount.rx += count;
-+ }
-+
-+ /* reset the UART timeout */
-+ UART_PUT_CR(port, ATMEL_US_STTTO);
-+}
-+
-+/*
-+ * Deal with parity, framing and overrun errors.
-+ */
-+static void atmel_pdc_rxerr(struct uart_port *port, unsigned int status)
-+{
-+ /* clear error */
-+ UART_PUT_CR(port, ATMEL_US_RSTSTA);
-+
-+ if (status & ATMEL_US_RXBRK) {
-+ status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME); /* ignore side-effect */
-+ port->icount.brk++;
-+ }
-+ if (status & ATMEL_US_PARE)
-+ port->icount.parity++;
-+ if (status & ATMEL_US_FRAME)
-+ port->icount.frame++;
-+ if (status & ATMEL_US_OVRE)
-+ port->icount.overrun++;
-+}
-+
-+/*
-+ * A transmission via the PDC is complete.
-+ */
-+static void atmel_pdc_endtx(struct uart_port *port)
-+{
-+ struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
-+ struct circ_buf *xmit = &port->info->xmit;
-+ struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
-+
-+ xmit->tail += pdc->ofs;
-+ if (xmit->tail >= SERIAL_XMIT_SIZE)
-+ xmit->tail -= SERIAL_XMIT_SIZE;
-+
-+ port->icount.tx += pdc->ofs;
-+ pdc->ofs = 0;
-+
-+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
-+ uart_write_wakeup(port);
-+}
-+
-+/*
-+ * The PDC transmitter is idle, so either start the next transfer or
-+ * disable the transmitter.
-+ */
-+static void atmel_pdc_txbufe(struct uart_port *port)
-+{
-+ struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
-+ struct circ_buf *xmit = &port->info->xmit;
-+ struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
-+ int count;
-+
-+ if (!uart_circ_empty(xmit)) {
-+ /* more to transmit - setup next transfer */
-+ UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS); /* disable PDC transmit */
-+ dma_sync_single_for_device(port->dev, pdc->dma_addr, pdc->dma_size, DMA_TO_DEVICE);
-+
-+ if (xmit->tail < xmit->head)
-+ count = xmit->head - xmit->tail;
-+ else
-+ count = SERIAL_XMIT_SIZE - xmit->tail;
-+ pdc->ofs = count;
-+
-+ UART_PUT_TPR(port, pdc->dma_addr + xmit->tail);
-+ UART_PUT_TCR(port, count);
-+ UART_PUT_PTCR(port, ATMEL_PDC_TXTEN); /* re-enable PDC transmit */
-+ }
-+ else {
-+ /* nothing left to transmit - disable the transmitter */
-+ UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS); /* disable PDC transmit */
-+ UART_PUT_IDR(port, ATMEL_US_ENDTX | ATMEL_US_TXBUFE);
-+ }
-+}
-+
-+/*
- * Characters received (called from interrupt handler)
- */
- static void atmel_rx_chars(struct uart_port *port)
-@@ -349,6 +522,14 @@ static irqreturn_t atmel_interrupt(int i
- status = UART_GET_CSR(port);
- pending = status & UART_GET_IMR(port);
- while (pending) {
-+ /* PDC receive */
-+ if (pending & ATMEL_US_ENDRX)
-+ atmel_pdc_endrx(port);
-+ if (pending & ATMEL_US_TIMEOUT)
-+ atmel_pdc_timeout(port);
-+ if (atmel_port->use_dma_rx && pending & (ATMEL_US_RXBRK | ATMEL_US_OVRE | ATMEL_US_FRAME | ATMEL_US_PARE))
-+ atmel_pdc_rxerr(port, pending);
-+
- /* Interrupt receive */
- if (pending & ATMEL_US_RXRDY)
- atmel_rx_chars(port);
-@@ -363,6 +544,12 @@ static irqreturn_t atmel_interrupt(int i
- if (pending & (ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC | ATMEL_US_CTSIC))
- wake_up_interruptible(&port->info->delta_msr_wait);
-
-+ /* PDC transmit */
-+ if (pending & ATMEL_US_ENDTX)
-+ atmel_pdc_endtx(port);
-+ if (pending & ATMEL_US_TXBUFE)
-+ atmel_pdc_txbufe(port);
-+
- /* Interrupt transmit */
- if (pending & ATMEL_US_TXRDY)
- atmel_tx_chars(port);
-@@ -401,6 +588,47 @@ static int atmel_startup(struct uart_por
- }
-
- /*
-+ * Initialize DMA (if necessary)
-+ */
-+ if (atmel_port->use_dma_rx) {
-+ int i;
-+
-+ for (i = 0; i < 2; i++) {
-+ struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
-+
-+ pdc->buf = kmalloc(PDC_BUFFER_SIZE, GFP_KERNEL);
-+ if (pdc->buf == NULL) {
-+ if (i != 0) {
-+ dma_unmap_single(port->dev, atmel_port->pdc_rx[0].dma_addr, PDC_BUFFER_SIZE, DMA_FROM_DEVICE);
-+ kfree(atmel_port->pdc_rx[0].buf);
-+ }
-+ free_irq(port->irq, port);
-+ return -ENOMEM;
-+ }
-+ pdc->dma_addr = dma_map_single(port->dev, pdc->buf, PDC_BUFFER_SIZE, DMA_FROM_DEVICE);
-+ pdc->dma_size = PDC_BUFFER_SIZE;
-+ pdc->ofs = 0;
-+ }
-+
-+ atmel_port->pdc_rx_idx = 0;
-+
-+ UART_PUT_RPR(port, atmel_port->pdc_rx[0].dma_addr);
-+ UART_PUT_RCR(port, PDC_BUFFER_SIZE);
-+
-+ UART_PUT_RNPR(port, atmel_port->pdc_rx[1].dma_addr);
-+ UART_PUT_RNCR(port, PDC_BUFFER_SIZE);
-+ }
-+ if (atmel_port->use_dma_tx) {
-+ struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
-+ struct circ_buf *xmit = &port->info->xmit;
-+
-+ pdc->buf = xmit->buf;
-+ pdc->dma_addr = dma_map_single(port->dev, pdc->buf, SERIAL_XMIT_SIZE, DMA_TO_DEVICE);
-+ pdc->dma_size = SERIAL_XMIT_SIZE;
-+ pdc->ofs = 0;
-+ }
-+
-+ /*
- * If there is a specific "open" function (to register
- * control line interrupts)
- */
-@@ -418,7 +646,15 @@ static int atmel_startup(struct uart_por
- UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
- UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN); /* enable xmit & rcvr */
-
-- UART_PUT_IER(port, ATMEL_US_RXRDY); /* enable receive only */
-+ if (atmel_port->use_dma_rx) {
-+ UART_PUT_RTOR(port, PDC_RX_TIMEOUT); /* set UART timeout */
-+ UART_PUT_CR(port, ATMEL_US_STTTO);
-+
-+ UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
-+ UART_PUT_PTCR(port, ATMEL_PDC_RXTEN); /* enable PDC controller */
-+ }
-+ else
-+ UART_PUT_IER(port, ATMEL_US_RXRDY); /* enable receive only */
-
- return 0;
- }
-@@ -431,6 +667,31 @@ static void atmel_shutdown(struct uart_p
- struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
-
- /*
-+ * Ensure everything is stopped.
-+ */
-+ atmel_stop_rx(port);
-+ atmel_stop_tx(port);
-+
-+ /*
-+ * Shut-down the DMA.
-+ */
-+ if (atmel_port->use_dma_rx) {
-+ int i;
-+
-+ for (i = 0; i < 2; i++) {
-+ struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
-+
-+ dma_unmap_single(port->dev, pdc->dma_addr, pdc->dma_size, DMA_FROM_DEVICE);
-+ kfree(pdc->buf);
-+ }
-+ }
-+ if (atmel_port->use_dma_tx) {
-+ struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
-+
-+ dma_unmap_single(port->dev, pdc->dma_addr, pdc->dma_size, DMA_TO_DEVICE);
-+ }
-+
-+ /*
- * Disable all interrupts, port and break condition.
- */
- UART_PUT_CR(port, ATMEL_US_RSTSTA);
-@@ -481,6 +742,7 @@ static void atmel_serial_pm(struct uart_
- */
- static void atmel_set_termios(struct uart_port *port, struct ktermios * termios, struct ktermios * old)
- {
-+ struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
- unsigned long flags;
- unsigned int mode, imr, quot, baud;
-
-@@ -490,7 +752,7 @@ static void atmel_set_termios(struct uar
- baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
- quot = uart_get_divisor(port, baud);
-
-- if (quot > 65535) { /* BRGR is 16-bit, so switch to slower clock */
-+ if (quot > 65535) { /* BRGR is 16-bit, so switch to slower clock */
- quot /= 8;
- mode |= ATMEL_US_USCLKS_MCK_DIV8;
- }
-@@ -539,6 +801,9 @@ static void atmel_set_termios(struct uar
- if (termios->c_iflag & (BRKINT | PARMRK))
- port->read_status_mask |= ATMEL_US_RXBRK;
-
-+ if (atmel_port->use_dma_rx) /* need to enable error interrupts */
-+ UART_PUT_IER(port, port->read_status_mask);
-+
- /*
- * Characters to ignore
- */
-@@ -717,6 +982,13 @@ static void __devinit atmel_init_port(st
- clk_enable(atmel_port->clk);
- port->uartclk = clk_get_rate(atmel_port->clk);
- }
-+
-+#ifdef SUPPORT_PDC
-+ atmel_port->use_dma_rx = data->use_dma_rx;
-+ atmel_port->use_dma_tx = data->use_dma_tx;
-+ if (atmel_port->use_dma_tx)
-+ port->fifosize = PDC_BUFFER_SIZE;
-+#endif
- }
-
- /*
-@@ -893,7 +1165,8 @@ static int atmel_serial_suspend(struct p
- struct uart_port *port = platform_get_drvdata(pdev);
- struct atmel_uart_port *atmel_port = (struct atmel_uart_port *) port;
-
-- if (device_may_wakeup(&pdev->dev) && !at91_suspend_entering_slow_clock())
-+ if (device_may_wakeup(&pdev->dev)
-+ && !clk_must_disable(atmel_port->clk))
- enable_irq_wake(port->irq);
- else {
- uart_suspend_port(&atmel_uart, port);
-Index: linux-2.6.22.19/drivers/spi/Kconfig
-===================================================================
---- linux-2.6.22.19.orig/drivers/spi/Kconfig
-+++ linux-2.6.22.19/drivers/spi/Kconfig
-@@ -55,6 +55,7 @@ comment "SPI Master Controller Drivers"
- config SPI_ATMEL
- tristate "Atmel SPI Controller"
- depends on (ARCH_AT91 || AVR32) && SPI_MASTER
-+ select SPI_AT91_MANUAL_CS if ARCH_AT91RM9200
- help
- This selects a driver for the Atmel SPI Controller, present on
- many AT32 (AVR32) and AT91 (ARM) chips.
-@@ -100,6 +101,24 @@ config SPI_BUTTERFLY
- inexpensive battery powered microcontroller evaluation board.
- This same cable can be used to flash new firmware.
-
-+config SPI_AT91
-+ tristate "AT91RM9200 Bitbang SPI Master"
-+ depends on SPI_MASTER && ARCH_AT91RM9200 && !SPI_ATMEL && EXPERIMENTAL
-+ select SPI_BITBANG
-+ select SPI_AT91_MANUAL_CS
-+ help
-+ This is dumb PIO bitbanging driver for the Atmel AT91RM9200.
-+ The SPI_ATMEL driver will be its replacement, using the native
-+ SPI hardware and its DMA controller.
-+
-+config SPI_AT91_MANUAL_CS
-+ bool
-+ depends on ARCH_AT91RM9200
-+ help
-+ Works around an AT91RM9200 problem whereby the SPI chip-select
-+ will be wrongly disabled. The workaround uses those pins as
-+ GPIOs instead of letting the SPI controller manage them.
-+
- config SPI_IMX
- tristate "Freescale iMX SPI controller"
- depends on SPI_MASTER && ARCH_IMX && EXPERIMENTAL
-Index: linux-2.6.22.19/drivers/spi/Makefile
-===================================================================
---- linux-2.6.22.19.orig/drivers/spi/Makefile
-+++ linux-2.6.22.19/drivers/spi/Makefile
-@@ -23,6 +23,7 @@ obj-$(CONFIG_SPI_MPC52xx_PSC) += mpc52x
- obj-$(CONFIG_SPI_MPC83xx) += spi_mpc83xx.o
- obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o
- obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx.o
-+obj-$(CONFIG_SPI_AT91) += spi_at91_bitbang.o
- # ... add above this line ...
-
- # SPI protocol drivers (device/link on bus)
-Index: linux-2.6.22.19/drivers/spi/spi_at91_bitbang.c
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/drivers/spi/spi_at91_bitbang.c
-@@ -0,0 +1,207 @@
-+/*
-+ * at91_spi.c - at91 SPI driver (BOOTSTRAP/BITBANG VERSION)
-+ *
-+ * Copyright (C) 2006 David Brownell
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
-+ */
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/platform_device.h>
-+
-+#include <linux/spi/spi.h>
-+#include <linux/spi/spi_bitbang.h>
-+
-+#include <asm/arch/gpio.h>
-+
-+
-+/*
-+ * FIXME this bitbanging version is just to help bootstrap systems until
-+ * there's a native SPI+IRQ+DMA controller driver ... such a driver should
-+ * be a drop-in replacement for this one, and much faster.
-+ *
-+ * remember:
-+ *
-+ * - other at91 parts (like at91sam9) have multiple controllers
-+ * and different pin muxing; this version is at91rm9200 specfic.
-+ *
-+ * - at91sam9261 SPI0 pins are directly muxed with MMC/SD pins.
-+ *
-+ * - rm9200 spi chipselects drop wrongly, so the native driver
-+ * will need to use gpios much like this does.
-+ *
-+ * - real hardware only allows 8..16 bits per word, while this
-+ * bitbanger allows 1..32 (incompatible superset).
-+ *
-+ * - this disregards clock parameters. with inlined gpio calls,
-+ * gcc 3.4.4 produces about 1.5 mbit/sec, more than 2x faster
-+ * than using the subroutined veresion from txrx_word().
-+ *
-+ * - suspend/resume and <linux/clk.h> support is missing ...
-+ */
-+
-+#define spi_miso_bit AT91_PIN_PA0
-+#define spi_mosi_bit AT91_PIN_PA1
-+#define spi_sck_bit AT91_PIN_PA2
-+
-+struct at91_spi {
-+ struct spi_bitbang bitbang;
-+ struct platform_device *pdev;
-+};
-+
-+/*----------------------------------------------------------------------*/
-+
-+static inline void setsck(struct spi_device *spi, int is_on)
-+{
-+ at91_set_gpio_value(spi_sck_bit, is_on);
-+}
-+
-+static inline void setmosi(struct spi_device *spi, int is_on)
-+{
-+ at91_set_gpio_value(spi_mosi_bit, is_on);
-+}
-+
-+static inline int getmiso(struct spi_device *spi)
-+{
-+ return at91_get_gpio_value(spi_miso_bit);
-+}
-+
-+static void at91_spi_chipselect(struct spi_device *spi, int is_active)
-+{
-+ unsigned long cs = (unsigned long) spi->controller_data;
-+
-+ /* set default clock polarity */
-+ if (is_active)
-+ setsck(spi, spi->mode & SPI_CPOL);
-+
-+ /* only support active-low (default) */
-+ at91_set_gpio_value(cs, !is_active);
-+}
-+
-+/*
-+ * NOTE: this is "as fast as we can"; it should be a function of
-+ * the device clock ...
-+ */
-+#define spidelay(X) do{} while(0)
-+
-+#define EXPAND_BITBANG_TXRX
-+#include <linux/spi/spi_bitbang.h>
-+
-+static u32 at91_spi_txrx_word_mode0(struct spi_device *spi,
-+ unsigned nsecs, u32 word, u8 bits)
-+{
-+ return bitbang_txrx_be_cpha0(spi, nsecs, 0, word, 8);
-+}
-+
-+static u32 at91_spi_txrx_word_mode1(struct spi_device *spi,
-+ unsigned nsecs, u32 word, u8 bits)
-+{
-+ return bitbang_txrx_be_cpha1(spi, nsecs, 0, word, 8);
-+}
-+
-+static u32 at91_spi_txrx_word_mode2(struct spi_device *spi,
-+ unsigned nsecs, u32 word, u8 bits)
-+{
-+ return bitbang_txrx_be_cpha0(spi, nsecs, 1, word, 8);
-+}
-+
-+static u32 at91_spi_txrx_word_mode3(struct spi_device *spi,
-+ unsigned nsecs, u32 word, u8 bits)
-+{
-+ return bitbang_txrx_be_cpha1(spi, nsecs, 1, word, 8);
-+}
-+
-+/*----------------------------------------------------------------------*/
-+
-+static int __init at91_spi_probe(struct platform_device *pdev)
-+{
-+ int status;
-+ struct spi_master *master;
-+ struct at91_spi *at91_spi;
-+
-+ if (pdev->id != 0) /* SPI0 bus */
-+ return -EINVAL;
-+
-+ master = spi_alloc_master(&pdev->dev, sizeof *at91_spi);
-+ if (!master)
-+ return -ENOMEM;
-+
-+ at91_spi = spi_master_get_devdata(master);
-+ at91_spi->pdev = pdev;
-+ platform_set_drvdata(pdev, at91_spi);
-+
-+ /* SPI and bitbang hookup */
-+ master->bus_num = 0;
-+ master->num_chipselect = 4;
-+
-+ at91_spi->bitbang.master = spi_master_get(master);
-+ at91_spi->bitbang.chipselect = at91_spi_chipselect;
-+ at91_spi->bitbang.txrx_word[SPI_MODE_0] = at91_spi_txrx_word_mode0;
-+ at91_spi->bitbang.txrx_word[SPI_MODE_1] = at91_spi_txrx_word_mode1;
-+ at91_spi->bitbang.txrx_word[SPI_MODE_2] = at91_spi_txrx_word_mode2;
-+ at91_spi->bitbang.txrx_word[SPI_MODE_3] = at91_spi_txrx_word_mode3;
-+
-+ status = spi_bitbang_start(&at91_spi->bitbang);
-+ if (status < 0)
-+ (void) spi_master_put(at91_spi->bitbang.master);
-+
-+ return status;
-+}
-+
-+static int __exit at91_spi_remove(struct platform_device *pdev)
-+{
-+ struct at91_spi *at91_spi = platform_get_drvdata(pdev);
-+ int status;
-+
-+ /* stop() unregisters child devices too */
-+ status = spi_bitbang_stop(&at91_spi->bitbang);
-+ (void) spi_master_put(at91_spi->bitbang.master);
-+
-+ platform_set_drvdata(pdev, NULL);
-+ return status;
-+}
-+
-+static struct platform_driver at91_spi_driver = {
-+ .probe = at91_spi_probe,
-+ .remove = __exit_p(at91_spi_remove),
-+ .driver = {
-+ .name = "at91_spi",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+static int __init at91_spi_init(void)
-+{
-+ at91_set_gpio_output(spi_sck_bit, 0);
-+ at91_set_gpio_output(spi_mosi_bit, 0);
-+ at91_set_gpio_input(spi_miso_bit, 1 /* pullup */);
-+
-+ /* register driver */
-+ return platform_driver_register(&at91_spi_driver);
-+}
-+
-+static void __exit at91_spi_exit(void)
-+{
-+ platform_driver_unregister(&at91_spi_driver);
-+}
-+
-+device_initcall(at91_spi_init);
-+module_exit(at91_spi_exit);
-+
-+MODULE_ALIAS("at91_spi.0");
-+
-+MODULE_DESCRIPTION("AT91 SPI support (BOOTSTRAP/BITBANG VERSION)");
-+MODULE_AUTHOR("David Brownell");
-+MODULE_LICENSE("GPL");
-Index: linux-2.6.22.19/drivers/usb/gadget/at91_udc.c
-===================================================================
---- linux-2.6.22.19.orig/drivers/usb/gadget/at91_udc.c
-+++ linux-2.6.22.19/drivers/usb/gadget/at91_udc.c
-@@ -1803,7 +1803,7 @@ static int at91udc_suspend(struct platfo
- */
- if ((!udc->suspended && udc->addr)
- || !wake
-- || at91_suspend_entering_slow_clock()) {
-+ || clk_must_disable(udc->fclk)) {
- pullup(udc, 0);
- wake = 0;
- } else
-Index: linux-2.6.22.19/drivers/usb/host/ohci-at91.c
-===================================================================
---- linux-2.6.22.19.orig/drivers/usb/host/ohci-at91.c
-+++ linux-2.6.22.19/drivers/usb/host/ohci-at91.c
-@@ -299,7 +299,7 @@ ohci_hcd_at91_drv_suspend(struct platfor
- *
- * REVISIT: some boards will be able to turn VBUS off...
- */
-- if (at91_suspend_entering_slow_clock()) {
-+ if (clk_must_disable(fclk)) {
- ohci_usb_reset (ohci);
- at91_stop_clock();
- }
-Index: linux-2.6.22.19/drivers/video/backlight/kb920x_bl.c
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/drivers/video/backlight/kb920x_bl.c
-@@ -0,0 +1,164 @@
-+/*
-+ * Backlight Driver for KB9202
-+ *
-+ * Copyright (c) 2006 KwikByte
-+ *
-+ * Based on Sharp's Corgi Backlight Driver
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/platform_device.h>
-+#include <linux/spinlock.h>
-+#include <linux/fb.h>
-+#include <linux/backlight.h>
-+
-+#include <asm/arch/gpio.h>
-+
-+/* The backlight is on(1)/off(0) */
-+#define KB9202_DEFAULT_INTENSITY 1
-+#define KB9202_MAX_INTENSITY 1
-+
-+static int kb9202bl_suspended;
-+static int current_intensity = 0;
-+static DEFINE_SPINLOCK(bl_lock);
-+
-+static int kb9202bl_set_intensity(struct backlight_device *bd)
-+{
-+ unsigned long flags;
-+ int intensity = bd->props.brightness;
-+
-+ if (bd->props.power != FB_BLANK_UNBLANK)
-+ intensity = 0;
-+ if (bd->props.fb_blank != FB_BLANK_UNBLANK)
-+ intensity = 0;
-+ if (kb9202bl_suspended)
-+ intensity = 0;
-+
-+ if ((!current_intensity) && (bd->props.power == FB_BLANK_UNBLANK))
-+ intensity = 1;
-+
-+ spin_lock_irqsave(&bl_lock, flags);
-+ if (intensity)
-+ gpio_set_value(AT91_PIN_PC23, 1);
-+ else
-+ gpio_set_value(AT91_PIN_PC23, 0);
-+ spin_unlock_irqrestore(&bl_lock, flags);
-+
-+ current_intensity = intensity;
-+
-+ return 0;
-+}
-+
-+static int kb9202bl_get_intensity(struct backlight_device *bd)
-+{
-+ return current_intensity;
-+}
-+
-+static struct backlight_ops kb9202bl_ops = {
-+ .get_brightness = kb9202bl_get_intensity,
-+ .update_status = kb9202bl_set_intensity,
-+};
-+
-+static int __init kb9202bl_probe(struct platform_device *pdev)
-+{
-+ struct backlight_device *bd;
-+
-+ bd = backlight_device_register ("kb9202-bl", &pdev->dev, NULL, &kb9202bl_ops);
-+ if (IS_ERR(bd))
-+ return PTR_ERR(bd);
-+
-+ platform_set_drvdata(pdev, bd);
-+
-+ bd->props.max_brightness = KB9202_MAX_INTENSITY;
-+ bd->props.brightness = KB9202_DEFAULT_INTENSITY;
-+ (void) kb9202bl_set_intensity(bd);
-+
-+ return 0;
-+}
-+
-+static int kb9202bl_remove(struct platform_device *pdev)
-+{
-+ struct backlight_device *bd = platform_get_drvdata(pdev);
-+
-+ bd->props.brightness = 0;
-+ bd->props.power = 0;
-+ (void) kb9202bl_set_intensity(bd);
-+
-+ backlight_device_unregister(bd);
-+
-+ return 0;
-+}
-+
-+#ifdef CONFIG_PM
-+static int kb9202bl_suspend(struct platform_device *dev, pm_message_t state)
-+{
-+ struct backlight_device *bd = platform_get_drvdata(pdev);
-+
-+ kb9202bl_suspended = 1;
-+ (void) kb9202bl_set_intensity(bd);
-+ return 0;
-+}
-+
-+static int kb9202bl_resume(struct platform_device *dev)
-+{
-+ struct backlight_device *bd = platform_get_drvdata(pdev);
-+
-+ kb9202bl_suspended = 0;
-+ (void) kb9202bl_set_intensity(bd);
-+ return 0;
-+}
-+#else
-+#define kb9202bl_suspend NULL
-+#define kb9202bl_resume NULL
-+#endif
-+
-+static struct platform_driver kb9202bl_driver = {
-+ .probe = kb9202bl_probe,
-+ .remove = kb9202bl_remove,
-+ .suspend = kb9202bl_suspend,
-+ .resume = kb9202bl_resume,
-+ .driver = {
-+ .name = "kb9202-bl",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+static struct platform_device *kb9202bl_device;
-+
-+static int __init kb9202bl_init(void)
-+{
-+ int ret;
-+
-+ ret = platform_driver_register(&kb9202bl_driver);
-+ if (!ret) {
-+ kb9202bl_device = platform_device_alloc("kb9202-bl", -1);
-+ if (!kb9202bl_device)
-+ return -ENOMEM;
-+
-+ ret = platform_device_add(kb9202bl_device);
-+ if (ret) {
-+ platform_device_put(kb9202bl_device);
-+ platform_driver_unregister(&kb9202bl_driver);
-+ }
-+ }
-+ return ret;
-+}
-+
-+static void __exit kb9202bl_exit(void)
-+{
-+ platform_device_unregister(kb9202bl_device);
-+ platform_driver_unregister(&kb9202bl_driver);
-+}
-+
-+module_init(kb9202bl_init);
-+module_exit(kb9202bl_exit);
-+
-+MODULE_AUTHOR("KwikByte <kb9200_dev@kwikbyte.com>");
-+MODULE_DESCRIPTION("KB9202 Backlight Driver");
-+MODULE_LICENSE("GPL");
-Index: linux-2.6.22.19/drivers/video/backlight/Kconfig
-===================================================================
---- linux-2.6.22.19.orig/drivers/video/backlight/Kconfig
-+++ linux-2.6.22.19/drivers/video/backlight/Kconfig
-@@ -71,3 +71,11 @@ config BACKLIGHT_CARILLO_RANCH
- help
- If you have a Intel LE80578 (Carillo Ranch) say Y to enable the
- backlight driver.
-+
-+config BACKLIGHT_KB920x
-+ tristate "KwikByte KB9202 Backlight Driver"
-+ depends on BACKLIGHT_CLASS_DEVICE && MACH_KB9200
-+ default y
-+ help
-+ If you have a KwikByte KB9202 board, say Y to enable the
-+ backlight driver.
-Index: linux-2.6.22.19/drivers/video/backlight/Makefile
-===================================================================
---- linux-2.6.22.19.orig/drivers/video/backlight/Makefile
-+++ linux-2.6.22.19/drivers/video/backlight/Makefile
-@@ -7,3 +7,4 @@ obj-$(CONFIG_BACKLIGHT_HP680) += hp680_b
- obj-$(CONFIG_BACKLIGHT_LOCOMO) += locomolcd.o
- obj-$(CONFIG_BACKLIGHT_PROGEAR) += progear_bl.o
- obj-$(CONFIG_BACKLIGHT_CARILLO_RANCH) += cr_bllcd.o
-+obj-$(CONFIG_BACKLIGHT_KB920x) += kb920x_bl.o
-Index: linux-2.6.22.19/drivers/video/Kconfig
-===================================================================
---- linux-2.6.22.19.orig/drivers/video/Kconfig
-+++ linux-2.6.22.19/drivers/video/Kconfig
-@@ -822,6 +822,17 @@ config FB_EPSON1355
- framebuffer. Product specs at
- <http://www.erd.epson.com/vdc/html/products.htm>.
-
-+config FB_S1D15605
-+ tristate "Epson S1D15605 framebuffer support"
-+ depends on FB
-+ default m if MACH_KB9200
-+ select FB_CFB_FILLRECT
-+ select FB_CFB_COPYAREA
-+ select FB_CFB_IMAGEBLIT
-+ help
-+ Build in support for the S1D15605 Epson Research 128x64
-+ LCD controller as a framebuffer.
-+
- config FB_S1D13XXX
- tristate "Epson S1D13XXX framebuffer support"
- depends on FB
-@@ -835,7 +846,7 @@ config FB_S1D13XXX
-
- config FB_ATMEL
- tristate "AT91/AT32 LCD Controller support"
-- depends on FB && (ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || AVR32)
-+ depends on FB && (ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || AVR32)
- select FB_CFB_FILLRECT
- select FB_CFB_COPYAREA
- select FB_CFB_IMAGEBLIT
-Index: linux-2.6.22.19/drivers/video/Makefile
-===================================================================
---- linux-2.6.22.19.orig/drivers/video/Makefile
-+++ linux-2.6.22.19/drivers/video/Makefile
-@@ -87,7 +87,8 @@ obj-$(CONFIG_FB_G364) += g36
- obj-$(CONFIG_FB_SA1100) += sa1100fb.o
- obj-$(CONFIG_FB_HIT) += hitfb.o
- obj-$(CONFIG_FB_EPSON1355) += epson1355fb.o
--obj-$(CONFIG_FB_ATMEL) += atmel_lcdfb.o
-+obj-$(CONFIG_FB_S1D15605) += s1d15605fb.o
-+obj-$(CONFIG_FB_ATMEL) += atmel_lcdfb.o
- obj-$(CONFIG_FB_PVR2) += pvr2fb.o
- obj-$(CONFIG_FB_VOODOO1) += sstfb.o
- obj-$(CONFIG_FB_ARMCLCD) += amba-clcd.o
-Index: linux-2.6.22.19/drivers/video/s1d15605fb.c
-===================================================================
---- /dev/null
-+++ linux-2.6.22.19/drivers/video/s1d15605fb.c
-@@ -0,0 +1,659 @@
-+/*
-+ * drivers/video/s1d15605.c
-+ *
-+ * Adapted from several sources including:
-+ * 1) Driver for AT91 LCD Controller
-+ * Copyright (C) 2006 Atmel
-+ *
-+ * 2) Copyright (C) 2005 S. Kevin Hester
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file COPYING in the main directory of this archive for
-+ * more details.
-+ *
-+ * This is a basic framebuffer driver for the Optrex F-51320 128x64 mono LCD
-+ * display. This display uses a clone of the common Epson SED 1531 display
-+ * controller.
-+ *
-+ * I've heavily borrowed code from the vfb.c driver.
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-+ */
-+
-+#ifdef DEBUG
-+#define MSG(string, args...) printk("s1d15605fb:" string, ##args)
-+#else
-+#define MSG(string, args...)
-+#endif
-+
-+#include <linux/kernel.h>
-+#include <linux/platform_device.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/interrupt.h>
-+#include <linux/clk.h>
-+#include <linux/fb.h>
-+#include <linux/init.h>
-+#include <linux/delay.h>
-+
-+#include <asm/uaccess.h>
-+
-+#include <asm/arch/board.h>
-+#include <asm/arch/gpio.h>
-+
-+#ifdef CONFIG_PMAC_BACKLIGHT
-+#include <asm/backlight.h>
-+#endif
-+
-+#define VIDEOWIDTH 128
-+#define VIDEOHEIGHT 64
-+#define VIDEODEPTH 1 /* bits/pixel */
-+#define VIDEOWIDTH_BYTES ((VIDEOWIDTH * VIDEODEPTH) / 8)
-+
-+/* The number of bytes that actually go to the device */
-+#define ACTUALVIDEOMEMSIZE (VIDEOWIDTH_BYTES * VIDEOHEIGHT)
-+#define VIDEOMEMSIZE PAGE_SIZE
-+
-+static struct fb_var_screeninfo s1d15605_default __initdata = {
-+ .xres = VIDEOWIDTH,
-+ .yres = VIDEOHEIGHT,
-+ .xres_virtual = VIDEOWIDTH,
-+ .yres_virtual = VIDEOHEIGHT,
-+ .bits_per_pixel = VIDEODEPTH,
-+ .red = { 0, 1, 0 },
-+ .green = { 0, 1, 0 },
-+ .blue = { 0, 1, 0 },
-+ .activate = FB_ACTIVATE_NOW,
-+ .pixclock = 20000,
-+ .vmode = FB_VMODE_NONINTERLACED,
-+};
-+
-+static struct fb_fix_screeninfo s1d15605_fix __initdata = {
-+ .id = "s1d15605",
-+ .type = FB_TYPE_PACKED_PIXELS,
-+ .visual = FB_VISUAL_MONO10,
-+ .xpanstep = 0,
-+ .ypanstep = 0,
-+ .ywrapstep = 0,
-+ .accel = FB_ACCEL_NONE,
-+};
-+
-+struct s1d15605fb_info {
-+ struct fb_info *info;
-+ char *mmio;
-+ unsigned long reset_pin;
-+ struct platform_device *pdev;
-+};
-+
-+/*
-+ * LCD device interface
-+ */
-+#define RESET_DISPLAY 0xE2
-+#define LCD_BIAS_1_9 0xA2
-+#define ADC_SELECT_REVERSE 0xA1
-+#define COMMON_OUTPUT_NORMAL 0xC0
-+#define V5_RESISTOR_RATIO 0x26
-+#define ELECTRONIC_VOLUME_SET 0x81
-+#define ELECTRONIC_VOLUME_INIT 0x20
-+#define POWER_CONTROL_SET 0x28
-+#define VOLTAGE_REGULATOR 0x02
-+#define VOLTAGE_FOLLOWER 0x01
-+#define BOOSTER_CIRCUIT 0x04
-+#define DISPLAY_ON 0xAF
-+#define START_LINE_SET 0x40
-+#define PAGE_ADDRESS_SET 0xB0
-+#define COLUMN_ADDRESS_HIGH 0x10
-+#define COLUMN_ADDRESS_LOW 0x00
-+#define RESISTOR_RATIO_START 0x20
-+
-+#define NUM_OF_PAGES 8
-+#define NUM_OF_COLUMNS 128
-+
-+#define WRITE_COMMAND(x) __raw_writeb((x), (sinfo)->mmio)
-+#define READ_COMMAND __raw_readb((sinfo)->mmio)
-+#define WRITE_DATA(x) __raw_writeb((x), (sinfo)->mmio + (0x10000))
-+#define READ_DATA __raw_readb((sinfo)->mmio + (0x10000))
-+
-+
-+/*
-+ * s1d15605fb_resize_framebuffer
-+ *
-+ * Free allocated space if different. Allocate on new of changed.
-+ * Returns -ENOMEM if the new framebuffer can not be allocated,
-+ * zero on success.
-+ */
-+static int s1d15605fb_resize_framebuffer(struct s1d15605fb_info *sinfo)
-+{
-+ struct fb_info *info = sinfo->info;
-+ struct fb_fix_screeninfo *fix = &info->fix;
-+ struct fb_var_screeninfo *var = &info->var;
-+ unsigned int new_size;
-+ void *new_vaddr;
-+
-+ new_size = ((var->xres_virtual * var->yres_virtual * var->bits_per_pixel) / 8);
-+
-+ MSG("%s: x (%d) y (%d) bpp (%d): new size 0x%08x\n", __FUNCTION__,
-+ var->xres_virtual, var->yres_virtual, var->bits_per_pixel, new_size);
-+
-+ if (new_size == fix->smem_len)
-+ return 0;
-+
-+ if (fix->smem_len) {
-+ kfree(info->screen_base);
-+ }
-+
-+ new_vaddr = kmalloc(new_size, GFP_KERNEL);
-+
-+ if (!new_vaddr) {
-+ fix->smem_len = 0;
-+ return -ENOMEM;
-+ }
-+
-+ info->screen_base = new_vaddr;
-+ fix->smem_start = (unsigned)new_vaddr;
-+ fix->smem_len = new_size;
-+ fix->line_length = (var->xres_virtual * var->bits_per_pixel) / 8;
-+
-+ dev_info(info->device,
-+ "%luKiB frame buffer at %08lx (mapped at %p)\n",
-+ (unsigned long)info->fix.smem_len / 1024,
-+ (unsigned long)info->fix.smem_start,
-+ info->screen_base);
-+
-+ return 0;
-+}
-+
-+
-+/*
-+ * The s1d15605 seems to be divided into eight 128 pixel wide pages (from top to
-+ * bottom) each page seems to be eight pixels high, where these eight pixels are
-+ * one byte
-+ */
-+static void s1d15605_update(struct fb_info *info)
-+{
-+ struct s1d15605fb_info *sinfo = info->par;
-+ int page, i, row, colmask;
-+ u8 retVal, *rowPtr;
-+
-+ WRITE_COMMAND(START_LINE_SET);
-+ for (page = 0; page < NUM_OF_PAGES; ++page) {
-+ WRITE_COMMAND(PAGE_ADDRESS_SET + page);
-+ WRITE_COMMAND(COLUMN_ADDRESS_HIGH);
-+ WRITE_COMMAND(COLUMN_ADDRESS_LOW);
-+
-+ for (i = 0; i < NUM_OF_COLUMNS; ++i)
-+ {
-+ /* point of opportunity: optimization */
-+ colmask = (1 << (i & 0x7));
-+ rowPtr = (u8*)(info->screen_base);
-+ rowPtr += (VIDEOWIDTH_BYTES * 8 * page);
-+ rowPtr += (i >> 3);
-+ retVal = 0;
-+ for (row = 0; row < 8; ++row)
-+ {
-+ retVal = (retVal >> 1) | (((*rowPtr) & colmask) ? 0x80 : 0);
-+ rowPtr += VIDEOWIDTH_BYTES;
-+ }
-+ WRITE_DATA(retVal);
-+ }
-+ }
-+
-+ WRITE_COMMAND(DISPLAY_ON);
-+}
-+
-+
-+/*
-+ * Setting the video mode has been split into two parts.
-+ * First part, xxxfb_check_var, must not write anything
-+ * to hardware, it should only verify and adjust var.
-+ * This means it doesn't alter par but it does use hardware
-+ * data from it to check this var.
-+ */
-+static int s1d15605_check_var(struct fb_var_screeninfo *var, struct fb_info *info)
-+{
-+ /*
-+ * Some very basic checks
-+ */
-+ if (!var->xres)
-+ var->xres = 1;
-+ if (!var->yres)
-+ var->yres = 1;
-+ if (var->xres > var->xres_virtual)
-+ var->xres_virtual = var->xres;
-+ if (var->yres > var->yres_virtual)
-+ var->yres_virtual = var->yres;
-+
-+ if(var->bits_per_pixel > VIDEODEPTH)
-+ return -EINVAL;
-+
-+ /*
-+ * Memory limit
-+ */
-+ if (((var->yres_virtual * var->bits_per_pixel * var->yres_virtual) >> 3) >
-+ ACTUALVIDEOMEMSIZE)
-+ return -ENOMEM;
-+
-+ /*
-+ * Now that we checked it we alter var. The reason being is that the video
-+ * mode passed in might not work but slight changes to it might make it
-+ * work. This way we let the user know what is acceptable.
-+ */
-+ switch (var->bits_per_pixel) {
-+ case 1:
-+ var->red.offset = var->green.offset = var->blue.offset = 0;
-+ var->red.length = var->green.length = var->blue.length
-+ = var->bits_per_pixel;
-+ break;
-+ default:
-+ return -EINVAL;
-+ }
-+
-+ var->xoffset = var->yoffset = 0;
-+ var->red.msb_right = var->green.msb_right = var->blue.msb_right =
-+ var->transp.msb_right = 0;
-+
-+ return 0;
-+}
-+
-+
-+/*
-+ * This routine actually sets the video mode. It's in here where we
-+ * the hardware state info->par and fix which can be affected by the
-+ * change in par. For this driver it doesn't do much.
-+ */
-+static int s1d15605_set_par(struct fb_info *info)
-+{
-+ int ret;
-+
-+ MSG("%s:\n", __func__);
-+ MSG(" * resolution: %ux%u (%ux%u virtual)\n",
-+ info->var.xres, info->var.yres,
-+ info->var.xres_virtual, info->var.yres_virtual);
-+
-+ ret = s1d15605fb_resize_framebuffer(info->par);
-+
-+ info->fix.visual = FB_VISUAL_MONO10;
-+ return ret;
-+}
-+
-+
-+/*
-+ * Set a single color register. The values supplied are already
-+ * rounded down to the hardware's capabilities (according to the
-+ * entries in the var structure). Return != 0 for invalid regno.
-+ */
-+static int s1d15605_setcolreg(u_int regno, u_int red, u_int green, u_int blue,
-+ u_int transp, struct fb_info *info)
-+{
-+ if (regno > 1) /* no. of hw registers - we only do mono now */
-+ return 1;
-+
-+ return 0;
-+}
-+
-+
-+/*
-+ * Currently, the routine will simply shut-off the backlight and prevent
-+ * updates/refreshes. Modify according to application.
-+ *
-+ * 0 unblank, 1 blank, 2 no vsync, 3 no hsync, 4 off
-+ */
-+static int s1d15605_blank(int blank, struct fb_info *info)
-+{
-+#ifdef CONFIG_PMAC_BACKLIGHT
-+ if (blank)
-+ pmac_backlight->props.power = FB_BLANK_POWERDOWN;
-+ else
-+ pmac_backlight->props.power = FB_BLANK_UNBLANK;
-+ backlight_update_status(pmac_backlight);
-+#endif
-+ return 1;
-+}
-+
-+
-+/*
-+ * Pan or Wrap the Display
-+ *
-+ * This call looks only at xoffset, yoffset and the FB_VMODE_YWRAP flag
-+ */
-+/*
-+static int s1d15605_pan_display(struct fb_var_screeninfo *var,
-+ struct fb_info *info)
-+{
-+ if (var->vmode & FB_VMODE_YWRAP) {
-+ if (var->yoffset < 0
-+ || var->yoffset >= info->var.yres_virtual
-+ || var->xoffset)
-+ return -EINVAL;
-+ } else {
-+ if (var->xoffset + var->xres > info->var.xres_virtual ||
-+ var->yoffset + var->yres > info->var.yres_virtual)
-+ return -EINVAL;
-+ }
-+ info->var.xoffset = var->xoffset;
-+ info->var.yoffset = var->yoffset;
-+ if (var->vmode & FB_VMODE_YWRAP)
-+ info->var.vmode |= FB_VMODE_YWRAP;
-+ else
-+ info->var.vmode &= ~FB_VMODE_YWRAP;
-+ return 0;
-+}
-+*/
-+
-+
-+static void s1d15605_copyarea(struct fb_info *info, const struct fb_copyarea *region)
-+{
-+ cfb_copyarea(info, region);
-+ s1d15605_update(info);
-+}
-+
-+
-+static void s1d15605_fillrect (struct fb_info *info, const struct fb_fillrect *rect)
-+{
-+ cfb_fillrect(info, rect);
-+ s1d15605_update(info);
-+}
-+
-+
-+static void s1d15605_imageblit(struct fb_info *p, const struct fb_image *image)
-+{
-+ cfb_imageblit(p, image);
-+ s1d15605_update(p);
-+}
-+
-+
-+/*
-+ * Write the users data to our framebuffer, and then trigger a psuedo DMA
-+ */
-+static ssize_t s1d15605_write(struct file *file, const char *buf,
-+ size_t count, loff_t *ppos)
-+{
-+ unsigned long p = *ppos;
-+ struct inode *inode = file->f_dentry->d_inode;
-+ int fbidx = iminor(inode);
-+ struct fb_info *info = registered_fb[fbidx];
-+ int err;
-+
-+ if (p > info->fix.smem_len)
-+ return -ENOSPC;
-+ if (count >= info->fix.smem_len)
-+ count = info->fix.smem_len;
-+ err = 0;
-+ if (count + p > info->fix.smem_len) {
-+ count = info->fix.smem_len - p;
-+ err = -ENOSPC;
-+ }
-+ if (count) {
-+ char *base_addr;
-+
-+ base_addr = info->screen_base;
-+ count -= copy_from_user(base_addr+p, buf, count);
-+ *ppos += count;
-+ err = -EFAULT;
-+ }
-+
-+ s1d15605_update(info);
-+
-+ if (count)
-+ return count;
-+
-+ return err;
-+}
-+
-+#ifdef USE_PRIVATE_VMA_FXS
-+static void s1d15605_vma_open(struct vm_area_struct *vma)
-+{
-+ // FIXME - store stats in the device data via vm_private_data
-+}
-+
-+
-+static void s1d15605_vma_close(struct vm_area_struct *vma)
-+{
-+ // FIXME - store stats in the device data via vm_private_data
-+}
-+
-+
-+static struct page *s1d15605_vma_nopage(struct vm_area_struct *vma,
-+ unsigned long address, int *type)
-+{
-+ struct page *page;
-+ struct fb_info *info = vma->vm_private_data;
-+
-+ page = virt_to_page(info->screen_base);
-+ get_page(page);
-+
-+ // FIXME - now someone has a link to our page, start periodically blitting
-+ // latest updates to the actual device.
-+
-+ return page;
-+}
-+
-+
-+static struct vm_operations_struct s1d15605_vm_ops = {
-+ .open = s1d15605_vma_open,
-+ .close = s1d15605_vma_close,
-+ .nopage = s1d15605_vma_nopage
-+};
-+
-+
-+/* We don't do much here - because we have special vm_ops */
-+static int s1d15605_mmap(struct fb_info *info, struct vm_area_struct *vma)
-+{
-+ vma->vm_ops = &s1d15605_vm_ops;
-+ vma->vm_flags |= VM_RESERVED;
-+ vma->vm_private_data = info;
-+ s1d15605_vma_open(vma);
-+
-+ return 0;
-+}
-+#endif /* USE_PRIVATE_VMA_FXS */
-+
-+
-+static struct fb_ops s1d15605fb_ops = {
-+ .owner = THIS_MODULE,
-+ .fb_check_var = s1d15605_check_var,
-+ .fb_set_par = s1d15605_set_par,
-+ .fb_setcolreg = s1d15605_setcolreg,
-+ .fb_blank = s1d15605_blank,
-+// .fb_pan_display = s1d15605_pan_display,
-+ .fb_fillrect = s1d15605_fillrect,
-+ .fb_copyarea = s1d15605_copyarea,
-+ .fb_imageblit = s1d15605_imageblit,
-+ .fb_write = s1d15605_write,
-+#ifdef USE_PRIVATE_VMA_FXS
-+ .fb_mmap = s1d15605_mmap,
-+#endif
-+};
-+
-+
-+static void s1d15605_device_init(struct s1d15605fb_info *sinfo) {
-+
-+ char value;
-+
-+ /* release the reset line by reading the device - proto hardware */
-+ value = READ_COMMAND;
-+ value = READ_COMMAND;
-+
-+#ifdef CONFIG_MACH_KB9200
-+ /* new boards have dedicated reset line */
-+ gpio_set_value(sinfo->reset_pin, 1);
-+#endif
-+
-+ /* initialize the device within 5ms */
-+ WRITE_COMMAND(RESET_DISPLAY);
-+ WRITE_COMMAND(LCD_BIAS_1_9);
-+ WRITE_COMMAND(ADC_SELECT_REVERSE);
-+ WRITE_COMMAND(COMMON_OUTPUT_NORMAL);
-+ WRITE_COMMAND(V5_RESISTOR_RATIO);
-+ WRITE_COMMAND(ELECTRONIC_VOLUME_SET);
-+ WRITE_COMMAND(ELECTRONIC_VOLUME_INIT);
-+ WRITE_COMMAND(POWER_CONTROL_SET | VOLTAGE_REGULATOR | VOLTAGE_FOLLOWER | BOOSTER_CIRCUIT);
-+ WRITE_COMMAND(DISPLAY_ON);
-+
-+ WRITE_COMMAND(RESISTOR_RATIO_START + 4);
-+ WRITE_COMMAND(ELECTRONIC_VOLUME_SET);
-+ WRITE_COMMAND(0x33);
-+}
-+
-+
-+static int s1d15605fb_probe(struct platform_device *pdev)
-+{
-+ struct device *dev = &pdev->dev;
-+ struct fb_info *info;
-+ struct s1d15605fb_info *sinfo;
-+ int ret;
-+
-+ MSG("%s\n", __func__);
-+
-+ if (!(info = framebuffer_alloc(sizeof(struct s1d15605fb_info), dev))) {
-+ dev_err(dev, "Cannot allocate framebuffer struct\n");
-+ return -ENOMEM;
-+ }
-+
-+ sinfo = info->par;
-+ sinfo->info = info;
-+ sinfo->pdev = pdev;
-+
-+ if (pdev->num_resources < 2) {
-+ dev_err(dev, "Resources unusable\n");
-+ ret = -ENODEV;
-+ goto free_info;
-+ }
-+
-+ info->fbops = &s1d15605fb_ops;
-+ strcpy(info->fix.id, pdev->name);
-+
-+ info->fix.mmio_start = pdev->resource[0].start;
-+ info->fix.mmio_len = pdev->resource[0].end - pdev->resource[0].start + 1;
-+ sinfo->reset_pin = pdev->resource[1].start;
-+
-+ ret = s1d15605fb_resize_framebuffer(sinfo);
-+ if (ret < 0) {
-+ dev_err(dev, "Cannot resize framebuffer: %d\n", ret);
-+ goto free_fb;
-+ }
-+
-+ if (!request_mem_region(info->fix.mmio_start,
-+ info->fix.mmio_len, pdev->name)) {
-+ ret = -EBUSY;
-+ goto free_fb;
-+ }
-+
-+ sinfo->mmio = ioremap(info->fix.mmio_start, info->fix.mmio_len);
-+ if (!sinfo->mmio) {
-+ dev_err(dev, "Cannot map LCD memory region\n");
-+ goto release_mem;
-+ }
-+
-+ s1d15605_device_init(sinfo);
-+
-+ ret = fb_find_mode(&info->var, info, NULL, NULL, 0, NULL, 1);
-+
-+ if (!ret || (ret == 4))
-+ info->var = s1d15605_default;
-+
-+ info->fix = s1d15605_fix;
-+ info->flags = FBINFO_FLAG_DEFAULT |
-+/* FBINFO_HWACCEL_YPAN | */
-+ FBINFO_HWACCEL_FILLRECT | FBINFO_HWACCEL_COPYAREA;
-+
-+ ret = register_framebuffer(info);
-+ if (ret < 0) {
-+ dev_err(dev, "Failed to register framebuffer device: %d\n", ret);
-+ goto unmap_mmio;
-+ }
-+
-+ dev_set_drvdata(dev, info);
-+
-+ memset(info->screen_base, 0, info->fix.smem_len);
-+ info->var.activate |= FB_ACTIVATE_NOW;
-+ ret = fb_set_var(info, &info->var);
-+ if (ret) {
-+ dev_warn(dev, "Unable to set display parameters\n");
-+ }
-+
-+ info->var.activate &= ~(FB_ACTIVATE_FORCE | FB_ACTIVATE_NOW);
-+
-+ dev_dbg(dev, "%s SUCCESS\n", __func__);
-+
-+ dev_info(dev, "Driver $Revision: 1.1 $\n");
-+
-+ return 0;
-+
-+unmap_mmio:
-+ iounmap(sinfo->mmio);
-+release_mem:
-+ release_mem_region(info->fix.mmio_start, info->fix.mmio_len);
-+free_fb:
-+ kfree(info->screen_base);
-+
-+free_info:
-+ framebuffer_release(info);
-+
-+ dev_dbg(dev, "%s FAILED\n", __func__);
-+ return ret;
-+}
-+
-+
-+static int s1d15605fb_remove(struct platform_device *pdev)
-+{
-+ struct device *dev = &pdev->dev;
-+ struct fb_info *info = dev_get_drvdata(dev);
-+ struct s1d15605fb_info *sinfo = info->par;
-+
-+ if (!sinfo)
-+ return 0;
-+
-+ unregister_framebuffer(info);
-+
-+ iounmap(sinfo->mmio);
-+ release_mem_region(info->fix.mmio_start, info->fix.mmio_len);
-+
-+ kfree(info->screen_base);
-+
-+ dev_set_drvdata(dev, NULL);
-+ framebuffer_release(info);
-+ return 0;
-+}
-+
-+
-+static struct platform_driver s1d15605fb_driver = {
-+ .probe = s1d15605fb_probe,
-+ .remove = s1d15605fb_remove,
-+ .driver = {
-+ .name = "s1d15605fb",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+
-+static int __init s1d15605fb_init(void)
-+{
-+ return platform_driver_register(&s1d15605fb_driver);
-+}
-+
-+
-+static void __exit s1d15605fb_exit(void)
-+{
-+ platform_driver_unregister(&s1d15605fb_driver);
-+}
-+
-+
-+module_init(s1d15605fb_init);
-+module_exit(s1d15605fb_exit);
-+
-+
-+MODULE_AUTHOR("KwikByte");
-+MODULE_DESCRIPTION("Epson S1D15605 LCD Controller framebuffer driver");
-+MODULE_LICENSE("GPL");
projects / openwrt / openwrt.git / commitdiff