kirkwood: add ZyXEL NSA325 device
authorAlberto Bursi <alberto.bursi@outlook.it>
Mon, 6 Feb 2017 10:40:52 +0000 (11:40 +0100)
committerFelix Fietkau <nbd@nbd.name>
Sat, 11 Feb 2017 20:16:28 +0000 (21:16 +0100)
This patch add ZyXEL NSA325 2-Bay Media Server

The ZyXEL NSA325 device is a Kirkwood based NAS:

- SoC: Marvell 88F6702 1600Mhz
- SDRAM memory: 512MB DDR2 400Mhz
- Gigabit ethernet: Marvell Alaska
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 5 Status LED (green/red)
- 1 Copy/Sync button
- 1 Reset button
- 2 SATA II ports (internal)
- 2 USB 2.0 ports (back)
- 1 USB 3.0 port (front)
- Fan (fixed speed)
- hardware watchdog in a mcu

Basically a bigger, more powerful version of NSA310,
installation is the same as they share the same flash layout.

A notable difference is that there is a hardware watchdog
in a mcu on the board, which is disabled by default in the LEDE u-boot.
The watchdog is also disabled with a GPIO activation through
raw register change when kwbooting or it would reset the board before
the new uboot was transferred.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove dead code]
target/linux/kirkwood/base-files/etc/board.d/01_leds
target/linux/kirkwood/base-files/etc/board.d/02_network
target/linux/kirkwood/base-files/lib/kirkwood.sh
target/linux/kirkwood/image/Makefile
target/linux/kirkwood/patches-4.4/194-nsa325.patch [new file with mode: 0644]

index 4518fc4..e6da9fd 100755 (executable)
@@ -41,6 +41,9 @@ case "$board" in
 "nsa310b")
        ucidef_set_led_default "health" "health" "nsa310:green:sys" "1"
        ;;
+"nsa325")
+       ucidef_set_led_default "health" "health" "nsa325:green:sys" "1"
+       ;;
 "sheevaplug" | \
 "sheevaplug-esata")
        ucidef_set_led_timer "health" "health" "sheevaplug:blue:health" "200" "800"
index b5406b0..b82086e 100755 (executable)
@@ -30,7 +30,7 @@ case "$board" in
        ucidef_add_switch "switch0" \
                "0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "5@eth0" "6@eth1"
        ;;
-"nsa310b")
+"nsa310b"|"nsa325")
        ucidef_set_interface_lan "eth0" "dhcp"
        ucidef_set_interface_macaddr "lan" $( mtd_get_mac_ascii uboot_env ethaddr )
        ;;
index f0efec4..2c7d7ba 100755 (executable)
@@ -65,6 +65,10 @@ kirkwood_board_detect() {
                name="nsa310s"
                ;;
 
+       "ZyXEL NSA325")
+               name="nsa325"
+               ;;
+
        *)
                name="generic"
                ;;
index ece7c1a..141505e 100644 (file)
@@ -11,7 +11,7 @@ include $(TOPDIR)/rules.mk
 include $(INCLUDE_DIR)/image.mk
 
 KERNEL_LOADADDR:=0x8000
-TARGET_DEVICES = linksys-audi linksys-viper dockstar goflexnet goflexhome iconnect pogo_e02 ib62x0 nsa310b
+TARGET_DEVICES = linksys-audi linksys-viper dockstar goflexnet goflexhome iconnect pogo_e02 ib62x0 nsa310b nsa325
 
 UBI_OPTS := -m 2048 -p 128KiB -s 512
 UBIFS_OPTS := -m 2048 -e 126KiB -c 4096
@@ -87,6 +87,13 @@ $(Device/dockstar)
   DEVICE_PACKAGES := kmod-r8169 kmod-gpio-button-hotplug kmod-hwmon-lm85
 endef
 
+define Device/nsa325
+$(Device/dockstar)
+  DEVICE_TITLE := ZyXEL NSA325 (v1 and v2)
+  DEVICE_DTS := kirkwood-nsa325
+  DEVICE_PACKAGES := kmod-gpio-button-hotplug kmod-rtc-pcf8563 kmod-usb3
+endef
+
 define Device/pogo_e02
 $(Device/dockstar)
   DEVICE_TITLE := Cloud Engines Pogoplug E02
diff --git a/target/linux/kirkwood/patches-4.4/194-nsa325.patch b/target/linux/kirkwood/patches-4.4/194-nsa325.patch
new file mode 100644 (file)
index 0000000..8e5cd77
--- /dev/null
@@ -0,0 +1,238 @@
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -205,6 +205,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
+       kirkwood-nsa310a.dtb \
+       kirkwood-nsa310b.dtb \
+       kirkwood-nsa310s.dtb \
++      kirkwood-nsa325.dtb \
+       kirkwood-openblocks_a6.dtb \
+       kirkwood-openblocks_a7.dtb \
+       kirkwood-openrd-base.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/kirkwood-nsa325.dts
+@@ -0,0 +1,225 @@
++/*
++ * Device tree file for Zyxel NSA325 and NSA325v2 NAS
++ */
++/dts-v1/;
++#include "kirkwood-nsa3x0-common.dtsi"
++
++/ {
++      model = "ZyXEL NSA325";
++      compatible = "zyxel,nsa325", "marvell,kirkwood-88f6282", "marvell,kirkwood";
++
++      memory {
++              device_type = "memory";
++              reg = <0x00000000 0x20000000>;
++      };
++
++      chosen {
++              bootargs = "console=ttyS0,115200";
++              stdout-path = &uart0;
++      };
++
++      mbus {
++              pcie-controller {
++                      status = "okay";
++
++                      pcie@1,0 {
++                              status = "okay";
++                      };
++              };
++      };
++
++      ocp@f1000000 {
++              pinctrl: pin-controller@10000 {
++                      pinctrl-names = "default";
++
++                      pmx_led_sata2_green: pmx-led-sata2-green {
++                              marvell,pins = "mpp12";
++                              marvell,function = "gpio";
++                      };
++
++                      pmx_led_sata2_red: pmx-led-sata2-red {
++                              marvell,pins = "mpp13";
++                              marvell,function = "gpio";
++                      };
++
++                      pmx_mcu_data: pmx-mcu-data {
++                              marvell,pins = "mpp14";
++                              marvell,function = "gpio";
++                      };
++
++                      pmx_led_usb_green: pmx-led-usb-green {
++                              marvell,pins = "mpp15";
++                              marvell,function = "gpio";
++                      };
++
++                      pmx_mcu_clk: pmx-mcu-clk {
++                              marvell,pins = "mpp16";
++                              marvell,function = "gpio";
++                      };
++
++                      pmx_mcu_act: pmx-mcu-act {
++                              marvell,pins = "mpp17";
++                              marvell,function = "gpio";
++                      };
++
++                      pmx_usb_power_off: pmx-usb-power-off {
++                              marvell,pins = "mpp21";
++                              marvell,function = "gpio";
++                      };
++
++                      pmx_led_sys_green: pmx-led-sys-green {
++                              marvell,pins = "mpp28";
++                              marvell,function = "gpio";
++                      };
++
++                      pmx_led_sys_orange: pmx-led-sys-orange {
++                              marvell,pins = "mpp29";
++                              marvell,function = "gpio";
++                      };
++
++                      pmx_led_sata1_green: pmx-led-sata1-green {
++                              marvell,pins = "mpp41";
++                              marvell,function = "gpio";
++                      };
++
++                      pmx_led_sata1_red: pmx-led-sata1-red {
++                              marvell,pins = "mpp42";
++                              marvell,function = "gpio";
++                      };
++
++                      pmx_beeper: pmx-beeper {
++                              marvell,pins = "mpp44";
++                              marvell,function = "gpio";
++                      };
++
++                      pmx_pwr_sata1: pmx-pwr-sata1 {
++                              marvell,pins = "mpp47";
++                              marvell,function = "gpio";
++                      };
++
++              };
++
++              /* This board uses the pcf8563 RTC instead of the SoC RTC */
++              rtc@10300 {
++                      status = "disabled";
++              };
++
++              i2c@11000 {
++                      status = "okay";
++
++                      pcf8563: pcf8563@51 {
++                              compatible = "nxp,pcf8563";
++                              reg = <0x51>;
++                      };
++              };
++
++      };
++
++      gpio-leds {
++              compatible = "gpio-leds";
++              pinctrl-0 = <&pmx_led_sata1_green &pmx_led_sata1_red
++                           &pmx_led_sata2_green &pmx_led_sata2_red
++                           &pmx_led_sys_green &pmx_led_sys_orange
++                           &pmx_led_copy_green &pmx_led_copy_red
++                           &pmx_led_usb_green>;
++              pinctrl-names = "default";
++
++              green-sata2 {
++                      label = "nsa325:green:sata2";
++                      gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
++                        linux,default-trigger = "ide-disk2";
++              };
++
++              red-sata2 {
++                      label = "nsa325:red:sata2";
++                      gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
++              };
++
++              green-usb {
++                      label = "nsa325:green:usb";
++                      gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
++                        linux,default-trigger = "usb-host";
++              };
++
++              green-sys {
++                      label = "nsa325:green:sys";
++                      gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
++                      linux,default-trigger = "default-on";
++              };
++
++              orange-sys {
++                      label = "nsa325:orange:sys";
++                      gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
++                      linux,default-trigger = "cpu0";
++              };
++
++              green-copy {
++                      label = "nsa325:green:copy";
++                      gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
++              };
++
++              red-copy {
++                      label = "nsa325:red:copy";
++                      gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
++              };
++
++              green-sata1 {
++                      label = "nsa325:green:sata1";
++                      gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
++                      linux,default-trigger = "ide-disk1";
++              };
++
++              red-sata1 {
++                      label = "nsa325:red:sata1";
++                      gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
++              };
++      };
++
++      regulators {
++              compatible = "simple-bus";
++              #address-cells = <1>;
++              #size-cells = <0>;
++              pinctrl-0 = <&pmx_usb_power_off &pmx_pwr_sata1>;
++              pinctrl-names = "default";
++
++              usb_power: regulator@1 {
++                      compatible = "regulator-fixed";
++                      reg = <1>;
++                      regulator-name = "USB Power";
++                      regulator-min-microvolt = <5000000>;
++                      regulator-max-microvolt = <5000000>;
++                      regulator-always-on;
++                      regulator-boot-on;
++                      enable-active-high;
++                      gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
++              };
++
++              sata1_power: regulator@2 {
++                      compatible = "regulator-fixed";
++                      reg = <2>;
++                      regulator-name = "SATA Power";
++                      regulator-min-microvolt = <5000000>;
++                      regulator-max-microvolt = <5000000>;
++                      regulator-always-on;
++                      regulator-boot-on;
++                      enable-active-high;
++                      gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>;
++              };
++      };
++};
++
++&mdio {
++      status = "okay";
++
++      ethphy0: ethernet-phy@1 {
++              reg = <1>;
++      };
++};
++
++&eth0 {
++      status = "okay";
++
++      ethernet0-port@0 {
++              phy-handle = <&ethphy0>;
++      };
++};