ath79: add support for TP-Link Archer C59v2
authorKeith Maika <keithm@aoeex.com>
Mon, 16 Sep 2019 16:45:02 +0000 (12:45 -0400)
committerDavid Bauer <mail@david-bauer.net>
Mon, 16 Sep 2019 19:40:06 +0000 (21:40 +0200)
Add ath79 support for Archer C59v2, previously supported by ar71xx.

TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB

Flash instruction:
  - via web UI:
    1. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin
    2. Login to router and open the Advanced tab
    3. Navigate to System Tools -> Firmware Upgrade
    4. Upload firmware using the Manual Upgrade form
  - via TFTP:
    1. Set PC to fixed ip address 192.168.0.66
    2. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin
       and rename it to tp_recovery.bin
    3. Start a tftp server with the file tp_recovery.bin in its root directory
    4. Turn off the router
    5. Press and hold Reset button
    6. Turn on router with the reset button pressed and wait ~15 seconds
    7. Release the reset button and after a short time
       the firmware should be transferred from the tftp server
    8. Wait ~30 second to complete recovery.

Signed-off-by: Keith Maika <keithm@aoeex.com>
target/linux/ath79/base-files/etc/board.d/01_leds
target/linux/ath79/base-files/etc/board.d/02_network
target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
target/linux/ath79/dts/qca9561_tplink_archer-c59-v2.dts [new file with mode: 0644]
target/linux/ath79/image/generic-tp-link.mk

index e317ce2..778316e 100755 (executable)
@@ -157,6 +157,7 @@ tplink,tl-wr842n-v3)
        ;;
 tplink,archer-c58-v1|\
 tplink,archer-c59-v1|\
+tplink,archer-c59-v2|\
 tplink,archer-c60-v1|\
 tplink,archer-c60-v2)
        ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x1E"
index 7d5f288..5b47af8 100755 (executable)
@@ -59,7 +59,8 @@ ath79_setup_interfaces()
        avm,fritz4020|\
        pcs,cr3000|\
        tplink,archer-c58-v1|\
-       tplink,archer-c59-v1)
+       tplink,archer-c59-v1|\
+       tplink,archer-c59-v2)
                ucidef_set_interface_wan "eth1"
                ucidef_add_switch "switch0" \
                        "0@eth0" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2"
index ed34322..446b729 100644 (file)
@@ -214,6 +214,7 @@ case "$FIRMWARE" in
                ;;
        tplink,archer-c58-v1|\
        tplink,archer-c59-v1|\
+       tplink,archer-c59-v2|\
        tplink,archer-c60-v1|\
        tplink,archer-c60-v2|\
        tplink,archer-c6-v2)
diff --git a/target/linux/ath79/dts/qca9561_tplink_archer-c59-v2.dts b/target/linux/ath79/dts/qca9561_tplink_archer-c59-v2.dts
new file mode 100644 (file)
index 0000000..e70afbf
--- /dev/null
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "qca9561_tplink_archer-c5x.dtsi"
+
+/ {
+       compatible = "tplink,archer-c59-v2", "qca,qca9560";
+       model = "TP-Link Archer C59 v2";
+};
+
+&leds {
+       usb     {
+               label = "tp-link:green:usb";
+               gpios = <&led_gpio 7 GPIO_ACTIVE_LOW>;
+               linux,default-trigger = "usbport";
+               trigger-sources = <&hub_port>;
+       };
+};
+
+&usb0 {
+       #address-cells = <1>;
+       #size-cells = <0>;
+       status = "okay";
+
+       hub_port: port@1 {
+               reg = <1>;
+               #trigger-source-cells = <0>;
+       };
+};
+
+&usb_phy0 {
+       status = "okay";
+};
+
+&spi {
+       status = "okay";
+       num-cs = <1>;
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <25000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "factory-boot";
+                               reg = <0x000000 0x020000>;
+                               read-only;
+                       };
+
+                       partition@20000 {
+                               label = "u-boot";
+                               reg = <0x020000 0x010000>;
+                               read-only;
+                       };
+
+                       mac: partition@30000 {
+                               label = "mac";
+                               reg = <0x030000 0x010000>;
+                               read-only;
+                       };
+
+                       partition@40000 {
+                               compatible = "denx,uimage";
+                               label = "firmware";
+                               reg = <0x040000 0xe10000>;
+                       };
+
+                       partition@e50000 {
+                               label = "tplink";
+                               reg = <0xe50000 0x1a0000>;
+                               read-only;
+                       };
+
+                       art: partition@ff0000 {
+                               label = "art";
+                               reg = <0xff0000 0x010000>;
+                               read-only;
+                       };
+               };
+       };
+};
index 1e63a6b..5519e9c 100644 (file)
@@ -60,6 +60,18 @@ define Device/tplink_archer-c59-v1
 endef
 TARGET_DEVICES += tplink_archer-c59-v1
 
+define Device/tplink_archer-c59-v2
+  $(Device/tplink-safeloader-uimage)
+  ATH_SOC := qca9561
+  IMAGE_SIZE := 14400k
+  DEVICE_MODEL := Archer C59
+  DEVICE_VARIANT := v2
+  TPLINK_BOARD_ID := ARCHER-C59-V2
+  DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-ath10k-ct ath10k-firmware-qca9888-ct
+  SUPPORTED_DEVICES += archer-c59-v2
+endef
+TARGET_DEVICES += tplink_archer-c59-v2
+
 define Device/tplink_archer-c60-v1
   $(Device/tplink-safeloader-uimage)
   ATH_SOC := qca9561