+++ /dev/null
-#
-# Makefile for the Broadcom BCM963xx SoC specific parts of the kernel
-#
-# Copyright (C) 2004 Broadcom Corporation
-#
-obj-y := irq.o prom.o setup.o time.o ser_init.o int-handler.o info.o wdt.o
-
-SRCBASE := $(TOPDIR)
-EXTRA_CFLAGS += -I$(SRCBASE)/include
+++ /dev/null
-/*
- * $Id$
- *
- * Copyright (C) 2007 OpenWrt.org
- * Copyright (C) 2007 Gabor Juhos <juhosg at openwrt.org>
- * Copyright (C) 2007 Florian Fainelli <florian@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/types.h>
-#include <linux/autoconf.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/module.h>
-
-#include <asm/bootinfo.h>
-#include <asm/addrspace.h>
-#include <asm/string.h>
-#include <asm/mach-bcm963xx/bootloaders.h>
-
-static char *boot_loader_names[BOOT_LOADER_LAST+1] = {
- [BOOT_LOADER_UNKNOWN] = "Unknown",
- [BOOT_LOADER_CFE] = "CFE",
- [BOOT_LOADER_REDBOOT] = "RedBoot",
- [BOOT_LOADER_CFE2] = "CFEv2"
-};
-
-/* boot loaders specific definitions */
-#define CFE_EPTSEAL 0x43464531 /* CFE1 is the magic number to recognize CFE from other bootloaders */
-
-int boot_loader_type;
-/*
- * Boot loader detection routines
- */
-static int __init detect_cfe(void)
-{
- /*
- * This method only works, when we are booted directly from the CFE.
- */
- uint32_t cfe_handle = (uint32_t) fw_arg0;
- uint32_t cfe_a1_val = (uint32_t) fw_arg1;
- uint32_t cfe_entry = (uint32_t) fw_arg2;
- uint32_t cfe_seal = (uint32_t) fw_arg3;
-
- /* Check for CFE by finding the CFE magic number */
- if (cfe_seal != CFE_EPTSEAL)
- /* We are not booted from CFE */
- return 0;
-
- /* cfe_a1_val must be 0, because only one CPU present in the ADM5120 SoC */
- if (cfe_a1_val != 0)
- return 0;
-
- /* The cfe_handle, and the cfe_entry must be kernel mode addresses */
- if ((cfe_handle < KSEG0) || (cfe_entry < KSEG0))
- return 0;
-
- return 1;
-}
-
-static int __init detect_redboot(void)
-{
- /* On Inventel Livebox, the boot loader is passed as a command line argument, check for it */
- if (!strncmp(arcs_cmdline, "boot_loader=RedBoot", 19))
- return 1;
- return 0;
-}
-
-void __init detect_bootloader(void)
-{
- if (detect_cfe()) {
- boot_loader_type = BOOT_LOADER_CFE;
- }
-
- if (detect_redboot()) {
- boot_loader_type = BOOT_LOADER_REDBOOT;
- }
- else {
- /* Some devices are using CFE, but it is not detected as is */
- boot_loader_type = BOOT_LOADER_CFE2;
- }
- printk("Boot loader is : %s\n", boot_loader_names[boot_loader_type]);
-}
-
-void __init detect_board(void)
-{
- switch (boot_loader_type)
- {
- case BOOT_LOADER_CFE:
- break;
- case BOOT_LOADER_REDBOOT:
- break;
- default:
- break;
- }
-}
-
-EXPORT_SYMBOL(boot_loader_type);
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2002 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-/*
- * Generic interrupt handler for Broadcom MIPS boards
- */
-
-#include <linux/autoconf.h>
-
-#include <asm/asm.h>
-#include <asm/mipsregs.h>
-#include <asm/regdef.h>
-#include <asm/stackframe.h>
-
-/*
- * MIPS IRQ Source
- * -------- ------
- * 0 Software (ignored)
- * 1 Software (ignored)
- * 2 Combined hardware interrupt (hw0)
- * 3 Hardware
- * 4 Hardware
- * 5 Hardware
- * 6 Hardware
- * 7 R4k timer
- */
-
- .text
- .set noreorder
- .set noat
- .align 5
- NESTED(brcmIRQ, PT_SIZE, sp)
- SAVE_ALL
- CLI
- .set noreorder
- .set at
-
- jal plat_irq_dispatch
- move a0, sp
-
- j ret_from_irq
- nop
-
- END(brcmIRQ)
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2002 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-/*
- * Interrupt control functions for Broadcom 963xx MIPS boards
- */
-
-#include <asm/atomic.h>
-
-#include <linux/delay.h>
-#include <linux/init.h>
-#include <linux/ioport.h>
-#include <linux/irq.h>
-#include <linux/interrupt.h>
-#include <linux/kernel.h>
-#include <linux/slab.h>
-#include <linux/module.h>
-
-#include <asm/irq.h>
-#include <asm/mipsregs.h>
-#include <asm/addrspace.h>
-#include <asm/signal.h>
-#include <6348_map_part.h>
-#include <6348_intr.h>
-#include <bcm_map_part.h>
-#include <bcm_intr.h>
-
-static void irq_dispatch_int(void)
-{
- unsigned int pendingIrqs;
- static unsigned int irqBit;
- static unsigned int isrNumber = 31;
-
- pendingIrqs = PERF->IrqStatus & PERF->IrqMask;
- if (!pendingIrqs) {
- return;
- }
-
- while (1) {
- irqBit <<= 1;
- isrNumber++;
- if (isrNumber == 32) {
- isrNumber = 0;
- irqBit = 0x1;
- }
- if (pendingIrqs & irqBit) {
- PERF->IrqMask &= ~irqBit; // mask
- do_IRQ(isrNumber + INTERNAL_ISR_TABLE_OFFSET);
- break;
- }
- }
-}
-
-static void irq_dispatch_ext(uint32 irq)
-{
- if (!(PERF->ExtIrqCfg & (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT)))) {
- printk("**** Ext IRQ mask. Should not dispatch ****\n");
- }
- /* disable and clear interrupt in the controller */
- PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_CLEAR_SHFT));
- PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT));
- do_IRQ(irq);
-}
-
-
-//extern void brcm_timer_interrupt(struct pt_regs *regs);
-
-asmlinkage void plat_irq_dispatch(void)
-{
- unsigned long cause;
-
- cause = read_c0_status() & read_c0_cause() & ST0_IM;
- if (cause & CAUSEF_IP7)
- do_IRQ(7);
- else if (cause & CAUSEF_IP2)
- irq_dispatch_int();
- else if (cause & CAUSEF_IP3)
- irq_dispatch_ext(INTERRUPT_ID_EXTERNAL_0);
- else if (cause & CAUSEF_IP4)
- irq_dispatch_ext(INTERRUPT_ID_EXTERNAL_1);
- else if (cause & CAUSEF_IP5)
- irq_dispatch_ext(INTERRUPT_ID_EXTERNAL_2);
- else if (cause & CAUSEF_IP6) {
- irq_dispatch_ext(INTERRUPT_ID_EXTERNAL_3);
- local_irq_disable();
- }
-}
-
-
-void enable_brcm_irq(unsigned int irq)
-{
- unsigned long flags;
-
- local_irq_save(flags);
- if( irq >= INTERNAL_ISR_TABLE_OFFSET ) {
- PERF->IrqMask |= (1 << (irq - INTERNAL_ISR_TABLE_OFFSET));
- }
- else if (irq >= INTERRUPT_ID_EXTERNAL_0 && irq <= INTERRUPT_ID_EXTERNAL_3) {
- /* enable and clear interrupt in the controller */
- PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_CLEAR_SHFT));
- PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT));
- }
- local_irq_restore(flags);
-}
-
-void disable_brcm_irq(unsigned int irq)
-{
- unsigned long flags;
-
- local_irq_save(flags);
- if( irq >= INTERNAL_ISR_TABLE_OFFSET ) {
- PERF->IrqMask &= ~(1 << (irq - INTERNAL_ISR_TABLE_OFFSET));
- }
- else if (irq >= INTERRUPT_ID_EXTERNAL_0 && irq <= INTERRUPT_ID_EXTERNAL_3) {
- /* disable interrupt in the controller */
- PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT));
- }
- local_irq_restore(flags);
-}
-
-void ack_brcm_irq(unsigned int irq)
-{
- /* Already done in brcm_irq_dispatch */
-}
-
-unsigned int startup_brcm_irq(unsigned int irq)
-{
- enable_brcm_irq(irq);
-
- return 0; /* never anything pending */
-}
-
-unsigned int startup_brcm_none(unsigned int irq)
-{
- return 0;
-}
-
-void end_brcm_irq(unsigned int irq)
-{
- if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
- enable_brcm_irq(irq);
-}
-
-void end_brcm_none(unsigned int irq)
-{
-}
-
-static struct hw_interrupt_type brcm_irq_type = {
- .typename = "MIPS",
- .startup = startup_brcm_irq,
- .shutdown = disable_brcm_irq,
- .enable = enable_brcm_irq,
- .disable = disable_brcm_irq,
- .ack = ack_brcm_irq,
- .end = end_brcm_irq,
- .set_affinity = NULL
-};
-
-static struct hw_interrupt_type brcm_irq_no_end_type = {
- .typename = "MIPS",
- .startup = startup_brcm_none,
- .shutdown = disable_brcm_irq,
- .enable = enable_brcm_irq,
- .disable = disable_brcm_irq,
- .ack = ack_brcm_irq,
- .end = end_brcm_none,
- .set_affinity = NULL
-};
-
-void __init arch_init_irq(void)
-{
- int i;
-
- clear_c0_status(ST0_BEV);
- change_c0_status(ST0_IM, (IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3 | IE_IRQ4));
-
- for (i = 0; i < NR_IRQS; i++) {
- irq_desc[i].status = IRQ_DISABLED;
- irq_desc[i].action = 0;
- irq_desc[i].depth = 1;
- irq_desc[i].chip = &brcm_irq_type;
- }
-}
-
-int request_external_irq(unsigned int irq,
- FN_HANDLER handler,
- unsigned long irqflags,
- const char * devname,
- void *dev_id)
-{
- unsigned long flags;
-
- local_irq_save(flags);
-
- PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_CLEAR_SHFT)); // Clear
- PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT)); // Mask
- PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_INSENS_SHFT)); // Edge insesnsitive
- PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_LEVEL_SHFT)); // Level triggered
- PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_SENSE_SHFT)); // Low level
-
- local_irq_restore(flags);
-
- return( request_irq(irq, handler, irqflags, devname, dev_id) );
-}
-
-/* VxWorks compatibility function(s). */
-
-unsigned int BcmHalMapInterrupt(FN_HANDLER pfunc, unsigned int param,
- unsigned int interruptId)
-{
- int nRet = -1;
- char *devname;
-
- devname = kmalloc(16, GFP_KERNEL);
- if (devname)
- sprintf( devname, "brcm_%d", interruptId );
-
- /* Set the IRQ description to not automatically enable the interrupt at
- * the end of an ISR. The driver that handles the interrupt must
- * explicitly call BcmHalInterruptEnable or enable_brcm_irq. This behavior
- * is consistent with interrupt handling on VxWorks.
- */
- irq_desc[interruptId].chip = &brcm_irq_no_end_type;
-
- if( interruptId >= INTERNAL_ISR_TABLE_OFFSET )
- {
- printk("BcmHalMapInterrupt : internal IRQ\n");
- nRet = request_irq( interruptId, pfunc, IRQF_DISABLED, devname, (void *) param );
- }
- else if (interruptId >= INTERRUPT_ID_EXTERNAL_0 && interruptId <= INTERRUPT_ID_EXTERNAL_3)
- {
- printk("BcmHalMapInterrupt : external IRQ\n");
- nRet = request_external_irq( interruptId, pfunc, IRQF_DISABLED, devname, (void *) param );
- }
-
- return( nRet );
-}
-
-
-EXPORT_SYMBOL(enable_brcm_irq);
-EXPORT_SYMBOL(disable_brcm_irq);
-EXPORT_SYMBOL(request_external_irq);
-EXPORT_SYMBOL(BcmHalMapInterrupt);
-
+++ /dev/null
-/*
- Copyright 2004 Broadcom Corp. All Rights Reserved.
- Copyright 2007 OpenWrt,org, Florian Fainelli <florian@openwrt.org>
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-*/
-/*
- * prom.c: PROM library initialization code.
- *
- */
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/sched.h>
-#include <linux/bootmem.h>
-#include <linux/blkdev.h>
-
-#include <asm/addrspace.h>
-#include <asm/bootinfo.h>
-#include <asm/cpu.h>
-#include <asm/time.h>
-#include <asm/mach-bcm963xx/bootloaders.h>
-#include <asm/mach-bcm963xx/6348_map_part.h>
-
-#include "../cfe/cfe_private.h"
-
-extern void __init detect_bootloader(void);
-extern void serial_init(void);
-extern int boot_loader_type;
-
-#define MACH_BCM MACH_BCM96348
-
-const char *get_system_type(void)
-{
- return "Broadcom BCM963xx";
-}
-
-void __init prom_init(void)
-{
- serial_init();
-
- printk("%s prom init\n", get_system_type() );
-
- PERF->IrqMask = 0;
-
- /* Detect the bootloader */
- detect_bootloader();
-
- /* Register 16MB RAM minus the ADSL SDRAM by default */
- add_memory_region(0, (0x01000000 - ADSL_SDRAM_IMAGE_SIZE), BOOT_MEM_RAM);
-
-}
-
-void __init prom_free_prom_memory(void)
-{
- /* We do not have any memory to free */
-}
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2004 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-/*
- * Broadcom bcm63xx serial port initialization, also prepare for printk
- * by registering with console_init
- *
- */
-
-#include <linux/autoconf.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/console.h>
-#include <linux/sched.h>
-
-#include <asm/addrspace.h>
-#include <asm/irq.h>
-#include <asm/reboot.h>
-#include <asm/gdb-stub.h>
-#include <asm/mc146818rtc.h>
-
-#include <bcm_map_part.h>
-#include <6348_map_part.h>
-#include <board.h>
-
-#define SER63XX_DEFAULT_BAUD 115200
-#define BD_BCM63XX_TIMER_CLOCK_INPUT (FPERIPH)
-#define stUart ((volatile Uart * const) UART_BASE)
-
-// Transmit interrupts
-#define TXINT (TXFIFOEMT | TXUNDERR | TXOVFERR)
-// Receive interrupts
-#define RXINT (RXFIFONE | RXOVFERR)
-
-/* --------------------------------------------------------------------------
- Name: serial_init
- Purpose: Initalize the UART
--------------------------------------------------------------------------- */
-void __init serial_init(void)
-{
- u32 tmpVal = SER63XX_DEFAULT_BAUD;
- ULONG clockFreqHz;
-
-#if defined(CONFIG_BCM96345)
- // Make sure clock is ticking
- PERF->blkEnables |= UART_CLK_EN;
-#endif
-
- /* Dissable channel's receiver and transmitter. */
- stUart->control &= ~(BRGEN|TXEN|RXEN);
-
- /*--------------------------------------------------------------------*/
- /* Write the table value to the clock select register. */
- /* DPullen - this is the equation to use: */
- /* value = clockFreqHz / baud / 32-1; */
- /* (snmod) Actually you should also take into account any necessary */
- /* rounding. Divide by 16, look at lsb, if 0, divide by 2 */
- /* and subtract 1. If 1, just divide by 2 */
- /*--------------------------------------------------------------------*/
- clockFreqHz = BD_BCM63XX_TIMER_CLOCK_INPUT;
- tmpVal = (clockFreqHz / tmpVal) / 16;
- if( tmpVal & 0x01 )
- tmpVal /= 2; //Rounding up, so sub is already accounted for
- else
- tmpVal = (tmpVal / 2) - 1; // Rounding down so we must sub 1
- stUart->baudword = tmpVal;
-
- /* Finally, re-enable the transmitter and receiver. */
- stUart->control |= (BRGEN|TXEN|RXEN);
-
- stUart->config = (BITS8SYM | ONESTOP);
- // Set the FIFO interrupt depth ... stUart->fifocfg = 0xAA;
- stUart->fifoctl = RSTTXFIFOS | RSTRXFIFOS;
- stUart->intMask = 0;
- stUart->intMask = RXINT | TXINT;
-}
-
-
-/* prom_putc()
- * Output a character to the UART
- */
-void prom_putc(char c)
-{
- /* Wait for Tx uffer to empty */
- while (! (READ16(stUart->intStatus) & TXFIFOEMT));
- /* Send character */
- stUart->Data = c;
-}
-
-/* prom_puts()
- * Write a string to the UART
- */
-void prom_puts(const char *s)
-{
- while (*s) {
- if (*s == '\n') {
- prom_putc('\r');
- }
- prom_putc(*s++);
- }
-}
-
-
-/* prom_getc_nowait()
- * Returns a character from the UART
- * Returns -1 if no characters available or corrupted
- */
-int prom_getc_nowait(void)
-{
- uint16 uStatus;
- int cData = -1;
-
- uStatus = READ16(stUart->intStatus);
-
- if (uStatus & RXFIFONE) { /* Do we have a character? */
- cData = READ16(stUart->Data) & 0xff; /* Read character */
- if (uStatus & (RXFRAMERR | RXPARERR)) { /* If we got an error, throw it away */
- cData = -1;
- }
- }
-
- return cData;
-}
-
-/* prom_getc()
- * Returns a charcter from the serial port
- * Will block until it receives a valid character
-*/
-char prom_getc(void)
-{
- int cData = -1;
-
- /* Loop until we get a valid character */
- while(cData == -1) {
- cData = prom_getc_nowait();
- }
- return (char) cData;
-}
-
-/* prom_testc()
- * Returns 0 if no characters available
- */
-int prom_testc(void)
-{
- uint16 uStatus;
-
- uStatus = READ16(stUart->intStatus);
-
- return (uStatus & RXFIFONE);
-}
-
-#if defined (CONFIG_REMOTE_DEBUG)
-/* Prevent other code from writing to the serial port */
-void _putc(char c) { }
-void _puts(const char *ptr) { }
-#else
-/* Low level outputs call prom routines */
-void _putc(char c) {
- prom_putc(c);
-}
-void _puts(const char *ptr) {
- prom_puts(ptr);
-}
-#endif
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2002 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-/*
- * Generic setup routines for Broadcom 963xx MIPS boards
- */
-
-#include <linux/autoconf.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/kernel.h>
-#include <linux/kdev_t.h>
-#include <linux/types.h>
-#include <linux/console.h>
-#include <linux/sched.h>
-#include <linux/mm.h>
-#include <linux/slab.h>
-#include <linux/module.h>
-#include <linux/pm.h>
-#include <linux/bootmem.h>
-
-#include <asm/addrspace.h>
-#include <asm/bcache.h>
-#include <asm/irq.h>
-#include <asm/time.h>
-#include <asm/reboot.h>
-#include <asm/gdb-stub.h>
-#include <asm/bootinfo.h>
-#include <asm/cpu.h>
-#include <asm/mach-bcm963xx/bootloaders.h>
-
-extern void brcm_time_init(void);
-extern int boot_loader_type;
-
-#include <linux/pci.h>
-#include <linux/delay.h>
-#include <bcm_map_part.h>
-#include <6348_map_part.h>
-#include <bcmpci.h>
-
-static volatile MpiRegisters * mpi = (MpiRegisters *)(MPI_BASE);
-
-/* This function should be in a board specific directory. For now,
- * assume that all boards that include this file use a Broadcom chip
- * with a soft reset bit in the PLL control register.
- */
-static void brcm_machine_restart(char *command)
-{
- const unsigned long ulSoftReset = 0x00000001;
- unsigned long *pulPllCtrl = (unsigned long *) 0xfffe0008;
- *pulPllCtrl |= ulSoftReset;
-}
-
-static void brcm_machine_halt(void)
-{
- printk("System halted\n");
- while (1);
-}
-
-static void mpi_SetLocalPciConfigReg(uint32 reg, uint32 value)
-{
- /* write index then value */
- mpi->pcicfgcntrl = PCI_CFG_REG_WRITE_EN + reg;;
- mpi->pcicfgdata = value;
-}
-
-static uint32 mpi_GetLocalPciConfigReg(uint32 reg)
-{
- /* write index then get value */
- mpi->pcicfgcntrl = PCI_CFG_REG_WRITE_EN + reg;;
- return mpi->pcicfgdata;
-}
-
-/*
- * mpi_ResetPcCard: Set/Reset the PcCard
- */
-static void mpi_ResetPcCard(int cardtype, BOOL bReset)
-{
- if (cardtype == MPI_CARDTYPE_NONE) {
- return;
- }
-
- if (cardtype == MPI_CARDTYPE_CARDBUS) {
- bReset = ! bReset;
- }
-
- if (bReset) {
- mpi->pcmcia_cntl1 = (mpi->pcmcia_cntl1 & ~PCCARD_CARD_RESET);
- } else {
- mpi->pcmcia_cntl1 = (mpi->pcmcia_cntl1 | PCCARD_CARD_RESET);
- }
-}
-
-/*
- * mpi_ConfigCs: Configure an MPI/EBI chip select
- */
-static void mpi_ConfigCs(uint32 cs, uint32 base, uint32 size, uint32 flags)
-{
- mpi->cs[cs].base = ((base & 0x1FFFFFFF) | size);
- mpi->cs[cs].config = flags;
-}
-
-/*
- * mpi_InitPcmciaSpace
- */
-static void mpi_InitPcmciaSpace(void)
-{
- // ChipSelect 4 controls PCMCIA Memory accesses
- mpi_ConfigCs(PCMCIA_COMMON_BASE, pcmciaMem, EBI_SIZE_1M, (EBI_WORD_WIDE|EBI_ENABLE));
- // ChipSelect 5 controls PCMCIA Attribute accesses
- mpi_ConfigCs(PCMCIA_ATTRIBUTE_BASE, pcmciaAttr, EBI_SIZE_1M, (EBI_WORD_WIDE|EBI_ENABLE));
- // ChipSelect 6 controls PCMCIA I/O accesses
- mpi_ConfigCs(PCMCIA_IO_BASE, pcmciaIo, EBI_SIZE_64K, (EBI_WORD_WIDE|EBI_ENABLE));
-
- mpi->pcmcia_cntl2 = ((PCMCIA_ATTR_ACTIVE << RW_ACTIVE_CNT_BIT) |
- (PCMCIA_ATTR_INACTIVE << INACTIVE_CNT_BIT) |
- (PCMCIA_ATTR_CE_SETUP << CE_SETUP_CNT_BIT) |
- (PCMCIA_ATTR_CE_HOLD << CE_HOLD_CNT_BIT));
-
- mpi->pcmcia_cntl2 |= (PCMCIA_HALFWORD_EN | PCMCIA_BYTESWAP_DIS);
-}
-
-/*
- * cardtype_vcc_detect: PC Card's card detect and voltage sense connection
- *
- * CD1#/ CD2#/ VS1#/ VS2#/ Card Initial Vcc
- * CCD1# CCD2# CVS1 CVS2 Type
- *
- * GND GND open open 16-bit 5 vdc
- *
- * GND GND GND open 16-bit 3.3 vdc
- *
- * GND GND open GND 16-bit x.x vdc
- *
- * GND GND GND GND 16-bit 3.3 & x.x vdc
- *
- *====================================================================
- *
- * CVS1 GND CCD1# open CardBus 3.3 vdc
- *
- * GND CVS2 open CCD2# CardBus x.x vdc
- *
- * GND CVS1 CCD2# open CardBus y.y vdc
- *
- * GND CVS2 GND CCD2# CardBus 3.3 & x.x vdc
- *
- * CVS2 GND open CCD1# CardBus x.x & y.y vdc
- *
- * GND CVS1 CCD2# open CardBus 3.3, x.x & y.y vdc
- *
- */
-static int cardtype_vcc_detect(void)
-{
- uint32 data32;
- int cardtype;
-
- cardtype = MPI_CARDTYPE_NONE;
- mpi->pcmcia_cntl1 = 0x0000A000; // Turn on the output enables and drive
- // the CVS pins to 0.
- data32 = mpi->pcmcia_cntl1;
- switch (data32 & 0x00000003) // Test CD1# and CD2#, see if card is plugged in.
- {
- case 0x00000003: // No Card is in the slot.
- printk("mpi: No Card is in the PCMCIA slot\n");
- break;
-
- case 0x00000002: // Partial insertion, No CD2#.
- printk("mpi: Card in the PCMCIA slot partial insertion, no CD2 signal\n");
- break;
-
- case 0x00000001: // Partial insertion, No CD1#.
- printk("mpi: Card in the PCMCIA slot partial insertion, no CD1 signal\n");
- break;
-
- case 0x00000000:
- mpi->pcmcia_cntl1 = 0x0000A0C0; // Turn off the CVS output enables and
- // float the CVS pins.
- mdelay(1);
- data32 = mpi->pcmcia_cntl1;
- // Read the Register.
- switch (data32 & 0x0000000C) // See what is on the CVS pins.
- {
- case 0x00000000: // CVS1 and CVS2 are tied to ground, only 1 option.
- printk("mpi: Detected 3.3 & x.x 16-bit PCMCIA card\n");
- cardtype = MPI_CARDTYPE_PCMCIA;
- break;
-
- case 0x00000004: // CVS1 is open or tied to CCD1/CCD2 and CVS2 is tied to ground.
- // 2 valid voltage options.
- switch (data32 & 0x00000003) // Test the values of CCD1 and CCD2.
- {
- case 0x00000003: // CCD1 and CCD2 are tied to 1 of the CVS pins.
- // This is not a valid combination.
- printk("mpi: Unknown card plugged into slot\n");
- break;
-
- case 0x00000002: // CCD2 is tied to either CVS1 or CVS2.
- mpi->pcmcia_cntl1 = 0x0000A080; // Drive CVS1 to a 0.
- mdelay(1);
- data32 = mpi->pcmcia_cntl1;
- if (data32 & 0x00000002) { // CCD2 is tied to CVS2, not valid.
- printk("mpi: Unknown card plugged into slot\n");
- } else { // CCD2 is tied to CVS1.
- printk("mpi: Detected 3.3, x.x and y.y Cardbus card\n");
- cardtype = MPI_CARDTYPE_CARDBUS;
- }
- break;
-
- case 0x00000001: // CCD1 is tied to either CVS1 or CVS2.
- // This is not a valid combination.
- printk("mpi: Unknown card plugged into slot\n");
- break;
-
- case 0x00000000: // CCD1 and CCD2 are tied to ground.
- printk("mpi: Detected x.x vdc 16-bit PCMCIA card\n");
- cardtype = MPI_CARDTYPE_PCMCIA;
- break;
- }
- break;
-
- case 0x00000008: // CVS2 is open or tied to CCD1/CCD2 and CVS1 is tied to ground.
- // 2 valid voltage options.
- switch (data32 & 0x00000003) // Test the values of CCD1 and CCD2.
- {
- case 0x00000003: // CCD1 and CCD2 are tied to 1 of the CVS pins.
- // This is not a valid combination.
- printk("mpi: Unknown card plugged into slot\n");
- break;
-
- case 0x00000002: // CCD2 is tied to either CVS1 or CVS2.
- mpi->pcmcia_cntl1 = 0x0000A040; // Drive CVS2 to a 0.
- mdelay(1);
- data32 = mpi->pcmcia_cntl1;
- if (data32 & 0x00000002) { // CCD2 is tied to CVS1, not valid.
- printk("mpi: Unknown card plugged into slot\n");
- } else {// CCD2 is tied to CVS2.
- printk("mpi: Detected 3.3 and x.x Cardbus card\n");
- cardtype = MPI_CARDTYPE_CARDBUS;
- }
- break;
-
- case 0x00000001: // CCD1 is tied to either CVS1 or CVS2.
- // This is not a valid combination.
- printk("mpi: Unknown card plugged into slot\n");
- break;
-
- case 0x00000000: // CCD1 and CCD2 are tied to ground.
- cardtype = MPI_CARDTYPE_PCMCIA;
- printk("mpi: Detected 3.3 vdc 16-bit PCMCIA card\n");
- break;
- }
- break;
-
- case 0x0000000C: // CVS1 and CVS2 are open or tied to CCD1/CCD2.
- // 5 valid voltage options.
-
- switch (data32 & 0x00000003) // Test the values of CCD1 and CCD2.
- {
- case 0x00000003: // CCD1 and CCD2 are tied to 1 of the CVS pins.
- // This is not a valid combination.
- printk("mpi: Unknown card plugged into slot\n");
- break;
-
- case 0x00000002: // CCD2 is tied to either CVS1 or CVS2.
- // CCD1 is tied to ground.
- mpi->pcmcia_cntl1 = 0x0000A040; // Drive CVS2 to a 0.
- mdelay(1);
- data32 = mpi->pcmcia_cntl1;
- if (data32 & 0x00000002) { // CCD2 is tied to CVS1.
- printk("mpi: Detected y.y vdc Cardbus card\n");
- } else { // CCD2 is tied to CVS2.
- printk("mpi: Detected x.x vdc Cardbus card\n");
- }
- cardtype = MPI_CARDTYPE_CARDBUS;
- break;
-
- case 0x00000001: // CCD1 is tied to either CVS1 or CVS2.
- // CCD2 is tied to ground.
-
- mpi->pcmcia_cntl1 = 0x0000A040; // Drive CVS2 to a 0.
- mdelay(1);
- data32 = mpi->pcmcia_cntl1;
- if (data32 & 0x00000001) {// CCD1 is tied to CVS1.
- printk("mpi: Detected 3.3 vdc Cardbus card\n");
- } else { // CCD1 is tied to CVS2.
- printk("mpi: Detected x.x and y.y Cardbus card\n");
- }
- cardtype = MPI_CARDTYPE_CARDBUS;
- break;
-
- case 0x00000000: // CCD1 and CCD2 are tied to ground.
- cardtype = MPI_CARDTYPE_PCMCIA;
- printk("mpi: Detected 5 vdc 16-bit PCMCIA card\n");
- break;
- }
- break;
-
- default:
- printk("mpi: Unknown card plugged into slot\n");
- break;
-
- }
- }
- return cardtype;
-}
-
-/*
- * mpi_DetectPcCard: Detect the plugged in PC-Card
- * Return: < 0 => Unknown card detected
- * 0 => No card detected
- * 1 => 16-bit card detected
- * 2 => 32-bit CardBus card detected
- */
-static int mpi_DetectPcCard(void)
-{
- int cardtype;
-
- cardtype = cardtype_vcc_detect();
- switch(cardtype) {
- case MPI_CARDTYPE_PCMCIA:
- mpi->pcmcia_cntl1 &= ~0x0000e000; // disable enable bits
- //mpi->pcmcia_cntl1 = (mpi->pcmcia_cntl1 & ~PCCARD_CARD_RESET);
- mpi->pcmcia_cntl1 |= (PCMCIA_ENABLE | PCMCIA_GPIO_ENABLE);
- mpi_InitPcmciaSpace();
- mpi_ResetPcCard(cardtype, FALSE);
- // Hold card in reset for 10ms
- mdelay(10);
- mpi_ResetPcCard(cardtype, TRUE);
- // Let card come out of reset
- mdelay(100);
- break;
- case MPI_CARDTYPE_CARDBUS:
- // 8 => CardBus Enable
- // 1 => PCI Slot Number
- // C => Float VS1 & VS2
- mpi->pcmcia_cntl1 = (mpi->pcmcia_cntl1 & 0xFFFF0000) |
- CARDBUS_ENABLE |
- (CARDBUS_SLOT << 8)|
- VS2_OEN |
- VS1_OEN;
- /* access to this memory window will be to/from CardBus */
- mpi->l2pmremap1 |= CARDBUS_MEM;
-
- // Need to reset the Cardbus Card. There's no CardManager to do this,
- // and we need to be ready for PCI configuration.
- mpi_ResetPcCard(cardtype, FALSE);
- // Hold card in reset for 10ms
- mdelay(10);
- mpi_ResetPcCard(cardtype, TRUE);
- // Let card come out of reset
- mdelay(100);
- break;
- default:
- break;
- }
- return cardtype;
-}
-
-static int mpi_init(void)
-{
- unsigned long data;
- unsigned int chipid, chiprev, sdramsize;
-
- printk("Broadcom BCM963xx MPI\n");
- chipid = (PERF->RevID & 0xFFFF0000) >> 16;
- chiprev = (PERF->RevID & 0xFF);
-
- if (boot_loader_type == BOOT_LOADER_CFE)
- sdramsize = boot_mem_map.map[0].size;
- else
- sdramsize = 0x01000000;
- /*
- * Init the pci interface
- */
- data = GPIO->GPIOMode; // GPIO mode register
- data |= GROUP2_PCI | GROUP1_MII_PCCARD; // PCI internal arbiter + Cardbus
- GPIO->GPIOMode = data; // PCI internal arbiter
-
- /*
- * In the BCM6348 CardBus support is defaulted to Slot 0
- * because there is no external IDSEL for CardBus. To disable
- * the CardBus and allow a standard PCI card in Slot 0
- * set the cbus_idsel field to 0x1f.
- */
- /*
- uData = mpi->pcmcia_cntl1;
- uData |= CARDBUS_IDSEL;
- mpi->pcmcia_cntl1 = uData;
- */
- // Setup PCI I/O Window range. Give 64K to PCI I/O
- mpi->l2piorange = ~(BCM_PCI_IO_SIZE_64KB-1);
- // UBUS to PCI I/O base address
- mpi->l2piobase = BCM_PCI_IO_BASE & BCM_PCI_ADDR_MASK;
- // UBUS to PCI I/O Window remap
- mpi->l2pioremap = (BCM_PCI_IO_BASE | MEM_WINDOW_EN);
-
- // enable PCI related GPIO pins and data swap between system and PCI bus
- mpi->locbuscntrl = (EN_PCI_GPIO | DIR_U2P_NOSWAP);
-
- /* Enable 6348 BusMaster and Memory access mode */
- data = mpi_GetLocalPciConfigReg(PCI_COMMAND);
- data |= (PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
- mpi_SetLocalPciConfigReg(PCI_COMMAND, data);
-
- /* Configure two 16 MByte PCI to System memory regions. */
- /* These memory regions are used when PCI device is a bus master */
- /* Accesses to the SDRAM from PCI bus will be "byte swapped" for this region */
- mpi_SetLocalPciConfigReg(PCI_BASE_ADDRESS_3, BCM_HOST_MEM_SPACE1);
- mpi->sp0remap = 0x0;
-
- /* Accesses to the SDRAM from PCI bus will not be "byte swapped" for this region */
- mpi_SetLocalPciConfigReg(PCI_BASE_ADDRESS_4, BCM_HOST_MEM_SPACE2);
- mpi->sp1remap = 0x0;
- mpi->pcimodesel |= (PCI_BAR2_NOSWAP | 0x40);
-
- if ((chipid == 0x6348) && (chiprev == 0xb0)) {
- mpi->sp0range = ~(sdramsize-1);
- mpi->sp1range = ~(sdramsize-1);
- }
- /*
- * Change 6348 PCI Cfg Reg. offset 0x40 to PCI memory read retry count infinity
- * by set 0 in bit 8~15. This resolve read Bcm4306 srom return 0xffff in
- * first read.
- */
- data = mpi_GetLocalPciConfigReg(BRCM_PCI_CONFIG_TIMER);
- data &= ~BRCM_PCI_CONFIG_TIMER_RETRY_MASK;
- data |= 0x00000080;
- mpi_SetLocalPciConfigReg(BRCM_PCI_CONFIG_TIMER, data);
-
- /* enable pci interrupt */
- mpi->locintstat |= (EXT_PCI_INT << 16);
-
- mpi_DetectPcCard();
-
- ioport_resource.start = BCM_PCI_IO_BASE;
- ioport_resource.end = BCM_PCI_IO_BASE + BCM_PCI_IO_SIZE_64KB;
-
-#if defined(CONFIG_USB)
- PERF->blkEnables |= USBH_CLK_EN;
- mdelay(100);
- *USBH_NON_OHCI = NON_OHCI_BYTE_SWAP;
-#endif
-
- return 0;
-}
-
-void __init plat_mem_setup(void)
-{
- _machine_restart = brcm_machine_restart;
- _machine_halt = brcm_machine_halt;
- pm_power_off = brcm_machine_halt;
-
- //board_time_init = brcm_time_init;
-
- /* mpi initialization */
- mpi_init();
-}
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2004 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-/*
- * Setup time for Broadcom 963xx MIPS boards
- */
-
-#include <linux/autoconf.h>
-#include <linux/init.h>
-#include <linux/kernel_stat.h>
-#include <linux/sched.h>
-#include <linux/spinlock.h>
-#include <linux/interrupt.h>
-#include <linux/module.h>
-#include <linux/time.h>
-#include <linux/timex.h>
-
-#include <asm/mipsregs.h>
-#include <asm/ptrace.h>
-#include <asm/div64.h>
-#include <asm/time.h>
-
-#include <6348_map_part.h>
-#include <6348_intr.h>
-#include <bcm_map_part.h>
-#include <bcm_intr.h>
-
-static unsigned long r4k_offset; /* Amount to increment compare reg each time */
-static unsigned long r4k_cur; /* What counter should be at next timer irq */
-
-/* *********************************************************************
- * calculateCpuSpeed()
- * Calculate the BCM6348 CPU speed by reading the PLL strap register
- * and applying the following formula:
- * cpu_clk = (.25 * 64MHz freq) * (N1 + 1) * (N2 + 2) / (M1_CPU + 1)
- * Input parameters:
- * none
- * Return value:
- * none
- ********************************************************************* */
-
-static inline unsigned long __init calculateCpuSpeed(void)
-{
- u32 pllStrap = PERF->PllStrap;
- int n1 = (pllStrap & PLL_N1_MASK) >> PLL_N1_SHFT;
- int n2 = (pllStrap & PLL_N2_MASK) >> PLL_N2_SHFT;
- int m1cpu = (pllStrap & PLL_M1_CPU_MASK) >> PLL_M1_CPU_SHFT;
-
- return (16 * (n1 + 1) * (n2 + 2) / (m1cpu + 1)) * 1000000;
-}
-
-
-static inline unsigned long __init cal_r4koff(void)
-{
- mips_hpt_frequency = calculateCpuSpeed() / 2;
- return (mips_hpt_frequency / HZ);
-}
-
-
-/*
- * There are a lot of conceptually broken versions of the MIPS timer interrupt
- * handler floating around. This one is rather different, but the algorithm
- * is provably more robust.
- */
-#if 0
-irqreturn_t brcm_timer_interrupt(struct pt_regs *regs)
-{
- int irq = MIPS_TIMER_INT;
-
- irq_enter();
- kstat_this_cpu.irqs[irq]++;
-
- timer_interrupt(irq, regs);
- irq_exit();
- return IRQ_HANDLED;
-}
-#endif
-
-void __init plat_time_init(void)
-{
- unsigned int est_freq, flags;
- local_irq_save(flags);
-
- printk("calculating r4koff... ");
- r4k_offset = cal_r4koff();
- printk("%08lx(%d)\n", r4k_offset, (int)r4k_offset);
-
- est_freq = 2 * r4k_offset * HZ;
- est_freq += 5000; /* round */
- est_freq -= est_freq % 10000;
- printk("CPU frequency %d.%02d MHz\n", est_freq / 1000000,
- (est_freq % 1000000) * 100 / 1000000);
- local_irq_restore(flags);
-}
-
-#if 0
-void __init plat_timer_setup(struct irqaction *irq)
-{
- r4k_cur = (read_c0_count() + r4k_offset);
- write_c0_compare(r4k_cur);
- set_c0_status(IE_IRQ5);
-}
-#endif
+++ /dev/null
-/*
- * Watchdog driver for the BCM963xx devices
- *
- * Copyright (C) 2007 OpenWrt.org
- * Florian Fainelli <florian@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/errno.h>
-#include <linux/miscdevice.h>
-#include <linux/fs.h>
-#include <linux/init.h>
-#include <linux/notifier.h>
-#include <linux/watchdog.h>
-#include <linux/timer.h>
-#include <linux/jiffies.h>
-#include <linux/completion.h>
-#include <linux/ioport.h>
-
-typedef struct bcm963xx_timer {
- unsigned short unused0;
- unsigned char timer_mask;
-#define TIMER0EN 0x01
-#define TIMER1EN 0x02
-#define TIMER2EN 0x04
- unsigned char timer_ints;
-#define TIMER0 0x01
-#define TIMER1 0x02
-#define TIMER2 0x04
-#define WATCHDOG 0x08
- unsigned long timer_ctl0;
- unsigned long timer_ctl1;
- unsigned long timer_ctl2;
-#define TIMERENABLE 0x80000000
-#define RSTCNTCLR 0x40000000
- unsigned long timer_cnt0;
- unsigned long timer_cnt1;
- unsigned long timer_cnt2;
- unsigned long wdt_def_count;
-
- /* Write 0xff00 0x00ff to Start timer
- * Write 0xee00 0x00ee to Stop and re-load default count
- * Read from this register returns current watch dog count
- */
- unsigned long wdt_ctl;
-
- /* Number of 40-MHz ticks for WD Reset pulse to last */
- unsigned long wdt_rst_count;
-} bcm963xx_timer;
-
-static struct bcm963xx_wdt_device {
- struct completion stop;
- volatile int running;
- struct timer_list timer;
- volatile int queue;
- int default_ticks;
- unsigned long inuse;
-} bcm963xx_wdt_device;
-
-static int ticks = 1000;
-
-#define WDT_BASE 0xfffe0200
-#define WDT ((volatile bcm963xx_timer * const) WDT_BASE)
-
-#define BCM963XX_INTERVAL (HZ/10+1)
-
-static void bcm963xx_wdt_trigger(unsigned long unused)
-{
- if (bcm963xx_wdt_device.running)
- ticks--;
-
- /* Load the default ticking value into the reset counter register */
- WDT->wdt_rst_count = bcm963xx_wdt_device.default_ticks;
-
- if (bcm963xx_wdt_device.queue && ticks) {
- bcm963xx_wdt_device.timer.expires = jiffies + BCM963XX_INTERVAL;
- add_timer(&bcm963xx_wdt_device.timer);
- }
- else {
- complete(&bcm963xx_wdt_device.stop);
- }
-}
-
-static void bcm963xx_wdt_reset(void)
-{
- ticks = bcm963xx_wdt_device.default_ticks;
- /* Also reload default count */
- WDT->wdt_def_count = ticks;
- WDT->wdt_ctl = 0xee00;
- WDT->wdt_ctl = 0x00ee;
-}
-
-static void bcm963xx_wdt_start(void)
-{
- if (!bcm963xx_wdt_device.queue) {
- bcm963xx_wdt_device.queue;
- /* Enable the watchdog by writing 0xff00 ,then 0x00ff to the control register */
- WDT->wdt_ctl = 0xff00;
- WDT->wdt_ctl = 0x00ff;
- bcm963xx_wdt_device.timer.expires = jiffies + BCM963XX_INTERVAL;
- add_timer(&bcm963xx_wdt_device.timer);
- }
- bcm963xx_wdt_device.running++;
-}
-
-static int bcm963xx_wdt_stop(void)
-{
- if (bcm963xx_wdt_device.running)
- bcm963xx_wdt_device.running = 0;
-
- ticks = bcm963xx_wdt_device.default_ticks;
-
- /* Stop the watchdog by writing 0xee00 then 0x00ee to the control register */
- WDT->wdt_ctl = 0xee00;
- WDT->wdt_ctl = 0x00ee;
-
- return -EIO;
-}
-
-static int bcm963xx_wdt_open(struct inode *inode, struct file *file)
-{
- if (test_and_set_bit(0, &bcm963xx_wdt_device.inuse))
- return -EBUSY;
- return nonseekable_open(inode, file);
-}
-
-static int bcm963xx_wdt_release(struct inode *inode, struct file *file)
-{
- clear_bit(0, &bcm963xx_wdt_device.inuse);
- return 0;
-}
-
-static int bcm963xx_wdt_ioctl(struct inode *inode, struct file *file,
- unsigned int cmd, unsigned long arg)
-{
- void __user *argp = (void __user *)arg;
- unsigned int value;
-
- static struct watchdog_info ident = {
- .options = WDIOF_CARDRESET,
- .identity = "BCM963xx WDT",
- };
-
- switch (cmd) {
- case WDIOC_KEEPALIVE:
- bcm963xx_wdt_reset();
- break;
- case WDIOC_GETSTATUS:
- /* Reading from the control register will return the current value */
- value = WDT->wdt_ctl;
- if ( copy_to_user(argp, &value, sizeof(int)) )
- return -EFAULT;
- break;
- case WDIOC_GETSUPPORT:
- if ( copy_to_user(argp, &ident, sizeof(ident)) )
- return -EFAULT;
- break;
- case WDIOC_SETOPTIONS:
- if ( copy_from_user(&value, argp, sizeof(int)) )
- return -EFAULT;
- switch(value) {
- case WDIOS_ENABLECARD:
- bcm963xx_wdt_start();
- break;
- case WDIOS_DISABLECARD:
- bcm963xx_wdt_stop();
- break;
- default:
- return -EINVAL;
- }
- break;
- default:
- return -ENOTTY;
- }
- return 0;
-}
-
-static int bcm963xx_wdt_write(struct file *file, const char __user *buf, size_t count, loff_t *ppos)
-{
- if (!count)
- return -EIO;
- bcm963xx_wdt_reset();
- return count;
-}
-
-static const struct file_operations bcm963xx_wdt_fops = {
- .owner = THIS_MODULE,
- .llseek = no_llseek,
- .write = bcm963xx_wdt_write,
- .ioctl = bcm963xx_wdt_ioctl,
- .open = bcm963xx_wdt_open,
- .release = bcm963xx_wdt_release,
-};
-
-static struct miscdevice bcm963xx_wdt_miscdev = {
- .minor = WATCHDOG_MINOR,
- .name = "watchdog",
- .fops = &bcm963xx_wdt_fops,
-};
-
-static void __exit bcm963xx_wdt_exit(void)
-{
- if (bcm963xx_wdt_device.queue ){
- bcm963xx_wdt_device.queue = 0;
- wait_for_completion(&bcm963xx_wdt_device.stop);
- }
- misc_deregister(&bcm963xx_wdt_miscdev);
-}
-
-static int __init bcm963xx_wdt_init(void)
-{
- int ret = 0;
-
- printk("Broadcom BCM963xx Watchdog timer\n");
-
- ret = misc_register(&bcm963xx_wdt_miscdev);
- if (ret) {
- printk(KERN_CRIT "Cannot register miscdev on minor=%d (err=%d)\n", WATCHDOG_MINOR, ret);
- return ret;
- }
- init_completion(&bcm963xx_wdt_device.stop);
- bcm963xx_wdt_device.queue = 0;
-
- clear_bit(0, &bcm963xx_wdt_device.inuse);
-
- init_timer(&bcm963xx_wdt_device.timer);
- bcm963xx_wdt_device.timer.function = bcm963xx_wdt_trigger;
- bcm963xx_wdt_device.timer.data = 0;
-
- bcm963xx_wdt_device.default_ticks = ticks;
- return ret;
-}
-
-
-module_init(bcm963xx_wdt_init);
-module_exit(bcm963xx_wdt_exit);
-
-MODULE_AUTHOR("Florian Fainelli <florian@openwrt.org>");
-MODULE_DESCRIPTION("Broadcom BCM963xx Watchdog driver");
-MODULE_LICENSE("GPL");
+++ /dev/null
-#
-# Makefile for the Broadcom Common Firmware Environment support
-#
-
-obj-y += cfe.o
+++ /dev/null
-/*
- * Broadcom Common Firmware Environment (CFE) support
- *
- * Copyright 2000, 2001, 2002
- * Broadcom Corporation. All rights reserved.
- *
- * Copyright (C) 2006 Michael Buesch
- *
- * Original Authors: Mitch Lichtenberg, Chris Demetriou
- *
- * This software is furnished under license and may be used and copied only
- * in accordance with the following terms and conditions. Subject to these
- * conditions, you may download, copy, install, use, modify and distribute
- * modified or unmodified copies of this software in source and/or binary
- * form. No title or ownership is transferred hereby.
- *
- * 1) Any source code used, modified or distributed must reproduce and
- * retain this copyright notice and list of conditions as they appear in
- * the source file.
- *
- * 2) No right is granted to use any trade name, trademark, or logo of
- * Broadcom Corporation. The "Broadcom Corporation" name may not be
- * used to endorse or promote products derived from this software
- * without the prior written permission of Broadcom Corporation.
- *
- * 3) THIS SOFTWARE IS PROVIDED "AS-IS" AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
- * NON-INFRINGEMENT ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM BE LIABLE
- * FOR ANY DAMAGES WHATSOEVER, AND IN PARTICULAR, BROADCOM SHALL NOT BE
- * LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
- * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
- * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
- * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
- * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
- * OR OTHERWISE), EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- */
-
-#include <linux/init.h>
-#include <linux/string.h>
-#include <linux/errno.h>
-#include <linux/spinlock.h>
-#include <asm/cfe.h>
-
-#include "cfe_private.h"
-
-
-static cfe_uint_t cfe_handle;
-static int (*cfe_trampoline)(long handle, long iocb);
-
-
-#include <linux/kernel.h>
-
-void __init cfe_setup(unsigned long fwarg0, unsigned long fwarg1,
- unsigned long fwarg2, unsigned long fwarg3)
-{
- if (fwarg3 == 0x80300000) {
- /* WRT54G workaround */
- fwarg3 = CFE_EPTSEAL;
- fwarg2 = 0xBFC00500;
- }
- if (fwarg3 != CFE_EPTSEAL) {
- /* We are not booted from CFE */
- return;
- }
- if (fwarg1 == 0) {
- /* We are on the boot CPU */
- cfe_handle = (cfe_uint_t)fwarg0;
- cfe_trampoline = CFE_TO_PTR(fwarg2);
- }
-}
-
-int cfe_vprintk(const char *fmt, va_list args)
-{
- static char buffer[1024];
- static DEFINE_SPINLOCK(lock);
- static const char pfx[] = "CFE-console: ";
- static const size_t pfx_len = sizeof(pfx) - 1;
- unsigned long flags;
- int len, cnt, pos;
- int handle;
- int res;
-
- if (!cfe_present())
- return -ENODEV;
-
- spin_lock_irqsave(&lock, flags);
- handle = cfe_getstdhandle(CFE_STDHANDLE_CONSOLE);
- if (CFE_ISERR(handle)) {
- len = -EIO;
- goto out;
- }
- strcpy(buffer, pfx);
- len = vscnprintf(buffer + pfx_len,
- sizeof(buffer) - pfx_len - 2,
- fmt, args);
- len += pfx_len;
- /* The CFE console requires CR-LF line-ends.
- * Add a CR, if we only terminate lines with a LF.
- * This does only fix CR-LF at the end of the string.
- * So for multiple lines, use multiple cfe_vprintk calls.
- */
- if (len > 1 &&
- buffer[len - 1] == '\n' && buffer[len - 2] != '\r') {
- buffer[len - 1] = '\r';
- buffer[len] = '\n';
- len += 1;
- }
- cnt = len;
- pos = 0;
- while (cnt > 0) {
- res = cfe_write(handle, buffer + pos, len - pos);
- if (CFE_ISERR(res)) {
- len = -EIO;
- goto out;
- }
- cnt -= res;
- pos += res;
- }
-out:
- spin_unlock_irqrestore(&lock, flags);
-
- return len;
-}
-
-int cfe_printk(const char *fmt, ...)
-{
- va_list args;
- int res;
-
- va_start(args, fmt);
- res = cfe_vprintk(fmt, args);
- va_end(args);
-
- return res;
-}
-
-static int cfe_iocb_dispatch(struct cfe_iocb *iocb)
-{
- if (!cfe_present())
- return CFE_ERR_UNSUPPORTED;
- return cfe_trampoline((long)cfe_handle, (long)iocb);
-}
-
-int cfe_present(void)
-{
- return (cfe_trampoline != NULL);
-}
-
-int cfe_close(int handle)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_DEV_CLOSE;
- iocb.handle = handle;
-
- err = cfe_iocb_dispatch(&iocb);
-
- return (CFE_ISERR(err)) ? err : iocb.status;
-}
-
-int cfe_cpu_start(int cpu, void (*fn)(void), long sp, long gp, long a1)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_FW_CPUCTL;
- iocb.psize = sizeof(struct cfe_iocb_cpuctl);
- iocb.cpuctl.number = cpu;
- iocb.cpuctl.command = CFE_CPU_CMD_START;
- iocb.cpuctl.gp = gp;
- iocb.cpuctl.sp = sp;
- iocb.cpuctl.a1 = a1;
- iocb.cpuctl.start_addr = (long)fn;
-
- err = cfe_iocb_dispatch(&iocb);
-
- return (CFE_ISERR(err)) ? err : iocb.status;
-}
-
-int cfe_cpu_stop(int cpu)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_FW_CPUCTL;
- iocb.psize = sizeof(struct cfe_iocb_cpuctl);
- iocb.cpuctl.number = cpu;
- iocb.cpuctl.command = CFE_CPU_CMD_STOP;
-
- err = cfe_iocb_dispatch(&iocb);
-
- return (CFE_ISERR(err)) ? err : iocb.status;
-}
-
-int cfe_enumenv(int idx, char *name, int namelen, char *val, int vallen)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_ENV_ENUM;
- iocb.psize = sizeof(struct cfe_iocb_envbuf);
- iocb.envbuf.index = idx;
- iocb.envbuf.name = PTR_TO_CFE(name);
- iocb.envbuf.name_len = namelen;
- iocb.envbuf.val = PTR_TO_CFE(val);
- iocb.envbuf.val_len = vallen;
-
- err = cfe_iocb_dispatch(&iocb);
-
- return (CFE_ISERR(err)) ? err : iocb.status;
-}
-
-int cfe_enumdev(int idx, char *name, int namelen)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
-
- iocb.fcode = CFE_CMD_DEV_ENUM;
- iocb.psize = sizeof(struct cfe_iocb_envbuf);
- iocb.envbuf.index = idx;
- iocb.envbuf.name = PTR_TO_CFE(name);
- iocb.envbuf.name_len = namelen;
-
- err = cfe_iocb_dispatch(&iocb);
-
- return (CFE_ISERR(err)) ? err : iocb.status;
-}
-
-int cfe_enummem(int idx, int flags, u64 *start, u64 *length,
- u64 *type)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
-
- iocb.fcode = CFE_CMD_FW_MEMENUM;
- iocb.flags = flags;
- iocb.psize = sizeof(struct cfe_iocb_meminfo);
- iocb.meminfo.index = idx;
-
- err = cfe_iocb_dispatch(&iocb);
- if (CFE_ISERR(err))
- return err;
- if (!CFE_ISERR(iocb.status)) {
- *start = iocb.meminfo.addr;
- *length = iocb.meminfo.size;
- *type = iocb.meminfo.type;
- }
-
- return iocb.status;
-}
-
-int cfe_exit(int warm, int status)
-{
- struct cfe_iocb iocb;
- int err;
-
-printk("CFE REBOOT\n");
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_FW_RESTART;
- if (warm)
- iocb.flags = CFE_FLG_WARMSTART;
- iocb.psize = sizeof(struct cfe_iocb_exitstat);
- iocb.exitstat.status = status;
-
-printk("CALL\n");
- err = cfe_iocb_dispatch(&iocb);
-printk("DONE\n");
-
- return (CFE_ISERR(err)) ? err : iocb.status;
-}
-
-int cfe_flushcache(int flags)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_FW_FLUSHCACHE;
- iocb.flags = flags;
-
- err = cfe_iocb_dispatch(&iocb);
-
- return (CFE_ISERR(err)) ? err : iocb.status;
-}
-
-int cfe_getdevinfo(char *name)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_DEV_GETINFO;
- iocb.psize = sizeof(struct cfe_iocb_buf);
- iocb.buffer.ptr = PTR_TO_CFE(name);
- iocb.buffer.length = strlen(name);
-
- err = cfe_iocb_dispatch(&iocb);
- if (CFE_ISERR(err))
- return err;
- if (CFE_ISERR(iocb.status))
- return iocb.status;
-
- return iocb.buffer.devflags;
-}
-
-int cfe_getenv(char *name, char *dest, int destlen)
-{
- struct cfe_iocb iocb;
- int err;
-
- dest[0] = '\0';
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_ENV_GET;
- iocb.psize = sizeof(struct cfe_iocb_envbuf);
- iocb.envbuf.name = PTR_TO_CFE(name);
- iocb.envbuf.name_len = strlen(name);
- iocb.envbuf.val = PTR_TO_CFE(dest);
- iocb.envbuf.val_len = destlen;
-
- err = cfe_iocb_dispatch(&iocb);
-
- return (CFE_ISERR(err)) ? err : iocb.status;
-}
-
-int cfe_getfwinfo(struct cfe_fwinfo *info)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_FW_GETINFO;
- iocb.psize = sizeof(struct cfe_iocb_fwinfo);
-
- err = cfe_iocb_dispatch(&iocb);
- if (CFE_ISERR(err))
- return err;
- if (CFE_ISERR(iocb.status))
- return err;
-
- info->version = iocb.fwinfo.version;
- info->totalmem = iocb.fwinfo.totalmem;
- info->flags = iocb.fwinfo.flags;
- info->boardid = iocb.fwinfo.boardid;
- info->bootarea_va = iocb.fwinfo.bootarea_va;
- info->bootarea_pa = iocb.fwinfo.bootarea_pa;
- info->bootarea_size = iocb.fwinfo.bootarea_size;
-
- return iocb.status;
-}
-
-int cfe_getstdhandle(int handletype)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_DEV_GETHANDLE;
- iocb.flags = handletype;
-
- err = cfe_iocb_dispatch(&iocb);
- if (CFE_ISERR(err))
- return err;
- if (CFE_ISERR(iocb.status))
- return iocb.status;
-
- return iocb.handle;
-}
-
-int cfe_getticks(s64 *ticks)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_FW_GETTIME;
- iocb.psize = sizeof(struct cfe_iocb_time);
-
- err = cfe_iocb_dispatch(&iocb);
- if (CFE_ISERR(err))
- return err;
- if (!CFE_ISERR(iocb.status))
- *ticks = iocb.time.ticks;
-
- return iocb.status;
-}
-
-int cfe_inpstat(int handle)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_DEV_INPSTAT;
- iocb.handle = handle;
- iocb.psize = sizeof(struct cfe_iocb_inpstat);
-
- err = cfe_iocb_dispatch(&iocb);
- if (CFE_ISERR(err))
- return err;
- if (CFE_ISERR(iocb.status))
- return iocb.status;
-
- return iocb.inpstat.status;
-}
-
-int cfe_ioctl(int handle, unsigned int ioctlnum,
- unsigned char *buffer, int length,
- int *retlen, u64 offset)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_DEV_IOCTL;
- iocb.handle = handle;
- iocb.psize = sizeof(struct cfe_iocb_buf);
- iocb.buffer.offset = offset;
- iocb.buffer.ioctlcmd = ioctlnum;
- iocb.buffer.ptr = PTR_TO_CFE(buffer);
- iocb.buffer.length = length;
-
- err = cfe_iocb_dispatch(&iocb);
- if (CFE_ISERR(err))
- return err;
- if (CFE_ISERR(iocb.status))
- return iocb.status;
- if (retlen)
- *retlen = iocb.buffer.retlen;
-
- return iocb.status;
-}
-
-int cfe_open(char *name)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_DEV_OPEN;
- iocb.psize = sizeof(struct cfe_iocb_buf);
- iocb.buffer.ptr = PTR_TO_CFE(name);
- iocb.buffer.length = strlen(name);
-
- err = cfe_iocb_dispatch(&iocb);
- if (CFE_ISERR(err))
- return err;
- if (CFE_ISERR(iocb.status))
- return iocb.status;
-
- return iocb.handle;
-}
-
-int cfe_read(int handle, unsigned char *buffer, int length)
-{
- return cfe_readblk(handle, 0, buffer, length);
-}
-
-int cfe_readblk(int handle, s64 offset, unsigned char *buffer, int length)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_DEV_READ;
- iocb.handle = handle;
- iocb.psize = sizeof(struct cfe_iocb_buf);
- iocb.buffer.offset = offset;
- iocb.buffer.ptr = PTR_TO_CFE(buffer);
- iocb.buffer.length = length;
-
- err = cfe_iocb_dispatch(&iocb);
- if (CFE_ISERR(err))
- return err;
- if (CFE_ISERR(iocb.status))
- return iocb.status;
-
- return iocb.buffer.retlen;
-}
-
-int cfe_setenv(char *name, char *val)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_ENV_SET;
- iocb.psize = sizeof(struct cfe_iocb_envbuf);
- iocb.envbuf.name = PTR_TO_CFE(name);
- iocb.envbuf.name_len = strlen(name);
- iocb.envbuf.val = PTR_TO_CFE(val);
- iocb.envbuf.val_len = strlen(val);
-
- err = cfe_iocb_dispatch(&iocb);
-
- return (CFE_ISERR(err)) ? err : iocb.status;
-}
-
-int cfe_write(int handle, unsigned char *buffer, int length)
-{
- return cfe_writeblk(handle, 0, buffer, length);
-}
-
-int cfe_writeblk(int handle, s64 offset, unsigned char *buffer, int length)
-{
- struct cfe_iocb iocb;
- int err;
-
- memset(&iocb, 0, sizeof(iocb));
- iocb.fcode = CFE_CMD_DEV_WRITE;
- iocb.handle = handle;
- iocb.psize = sizeof(struct cfe_iocb_buf);
- iocb.buffer.offset = offset;
- iocb.buffer.ptr = PTR_TO_CFE(buffer);
- iocb.buffer.length = length;
-
- err = cfe_iocb_dispatch(&iocb);
- if (CFE_ISERR(err))
- return err;
- if (CFE_ISERR(iocb.status))
- return iocb.status;
-
- return iocb.buffer.retlen;
-}
+++ /dev/null
-/*
- * Broadcom Common Firmware Environment (CFE) support
- *
- * Copyright 2000, 2001, 2002
- * Broadcom Corporation. All rights reserved.
- *
- * Copyright (C) 2006 Michael Buesch
- *
- * Original Authors: Mitch Lichtenberg, Chris Demetriou
- *
- * This software is furnished under license and may be used and copied only
- * in accordance with the following terms and conditions. Subject to these
- * conditions, you may download, copy, install, use, modify and distribute
- * modified or unmodified copies of this software in source and/or binary
- * form. No title or ownership is transferred hereby.
- *
- * 1) Any source code used, modified or distributed must reproduce and
- * retain this copyright notice and list of conditions as they appear in
- * the source file.
- *
- * 2) No right is granted to use any trade name, trademark, or logo of
- * Broadcom Corporation. The "Broadcom Corporation" name may not be
- * used to endorse or promote products derived from this software
- * without the prior written permission of Broadcom Corporation.
- *
- * 3) THIS SOFTWARE IS PROVIDED "AS-IS" AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
- * NON-INFRINGEMENT ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM BE LIABLE
- * FOR ANY DAMAGES WHATSOEVER, AND IN PARTICULAR, BROADCOM SHALL NOT BE
- * LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
- * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
- * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
- * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
- * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
- * OR OTHERWISE), EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- */
-
-#ifndef LINUX_CFE_PRIVATE_H_
-#define LINUX_CFE_PRIVATE_H_
-
-#ifndef __ASSEMBLY__
-
-/* Seal indicating CFE's presence, passed to the kernel. */
-#define CFE_EPTSEAL 0x43464531
-
-#define CFE_CMD_FW_GETINFO 0
-#define CFE_CMD_FW_RESTART 1
-#define CFE_CMD_FW_BOOT 2
-#define CFE_CMD_FW_CPUCTL 3
-#define CFE_CMD_FW_GETTIME 4
-#define CFE_CMD_FW_MEMENUM 5
-#define CFE_CMD_FW_FLUSHCACHE 6
-
-#define CFE_CMD_DEV_GETHANDLE 9
-#define CFE_CMD_DEV_ENUM 10
-#define CFE_CMD_DEV_OPEN 11
-#define CFE_CMD_DEV_INPSTAT 12
-#define CFE_CMD_DEV_READ 13
-#define CFE_CMD_DEV_WRITE 14
-#define CFE_CMD_DEV_IOCTL 15
-#define CFE_CMD_DEV_CLOSE 16
-#define CFE_CMD_DEV_GETINFO 17
-
-#define CFE_CMD_ENV_ENUM 20
-#define CFE_CMD_ENV_GET 22
-#define CFE_CMD_ENV_SET 23
-#define CFE_CMD_ENV_DEL 24
-
-#define CFE_CMD_MAX 32
-
-#define CFE_CMD_VENDOR_USE 0x8000 /* codes above this are for customer use */
-
-typedef u64 cfe_uint_t;
-typedef s64 cfe_int_t;
-typedef s64 cfe_ptr_t;
-
-/* Cast a pointer from native to CFE-API pointer and back */
-#define CFE_TO_PTR(p) ((void *)(unsigned long)(p))
-#define PTR_TO_CFE(p) ((cfe_ptr_t)(unsigned long)(p))
-
-struct cfe_iocb_buf {
- cfe_uint_t offset; /* offset on device (bytes) */
- cfe_ptr_t ptr; /* pointer to a buffer */
- cfe_uint_t length; /* length of this buffer */
- cfe_uint_t retlen; /* returned length (for read ops) */
- union {
- cfe_uint_t ioctlcmd; /* IOCTL command (used only for IOCTLs) */
- cfe_uint_t devflags; /* Returned device info flags */
- };
-};
-
-struct cfe_iocb_inpstat {
- cfe_uint_t status; /* 1 means input available */
-};
-
-struct cfe_iocb_envbuf {
- cfe_int_t index; /* 0-based enumeration index */
- cfe_ptr_t name; /* name string buffer */
- cfe_int_t name_len; /* size of name buffer */
- cfe_ptr_t val; /* value string buffer */
- cfe_int_t val_len; /* size of value string buffer */
-};
-
-struct cfe_iocb_cpuctl {
- cfe_uint_t number; /* cpu number to control */
- cfe_uint_t command; /* command to issue to CPU */
- cfe_uint_t start_addr; /* CPU start address */
- cfe_uint_t gp; /* starting GP value */
- cfe_uint_t sp; /* starting SP value */
- cfe_uint_t a1; /* starting A1 value */
-};
-
-struct cfe_iocb_time {
- cfe_int_t ticks; /* current time in ticks */
-};
-
-struct cfe_iocb_exitstat {
- cfe_int_t status;
-};
-
-struct cfe_iocb_meminfo {
- cfe_int_t index; /* 0-based enumeration index */
- cfe_int_t type; /* type of memory block */
- cfe_uint_t addr; /* physical start address */
- cfe_uint_t size; /* block size */
-};
-
-struct cfe_iocb_fwinfo {
- cfe_int_t version; /* major, minor, eco version */
- cfe_int_t totalmem; /* total installed mem */
- cfe_int_t flags; /* various flags */
- cfe_int_t boardid; /* board ID */
- cfe_int_t bootarea_va; /* VA of boot area */
- cfe_int_t bootarea_pa; /* PA of boot area */
- cfe_int_t bootarea_size; /* size of boot area */
- cfe_int_t reserved1;
- cfe_int_t reserved2;
- cfe_int_t reserved3;
-};
-
-/* CFE I/O Control Block */
-struct cfe_iocb {
- cfe_uint_t fcode; /* IOCB function code */
- cfe_int_t status; /* return status */
- cfe_int_t handle; /* file/device handle */
- cfe_uint_t flags; /* flags for this IOCB */
- cfe_uint_t psize; /* size of parameter list */
- union {
- struct cfe_iocb_buf buffer; /* buffer parameters */
- struct cfe_iocb_inpstat inpstat; /* input status parameters */
- struct cfe_iocb_envbuf envbuf; /* environment function parameters */
- struct cfe_iocb_cpuctl cpuctl; /* CPU control parameters */
- struct cfe_iocb_time time; /* timer parameters */
- struct cfe_iocb_meminfo meminfo; /* memory arena info parameters */
- struct cfe_iocb_fwinfo fwinfo; /* firmware information */
- struct cfe_iocb_exitstat exitstat; /* Exit Status */
- };
-};
-
-
-#include <linux/init.h>
-
-void __init cfe_setup(unsigned long fwarg0, unsigned long fwarg1,
- unsigned long fwarg2, unsigned long fwarg3);
-
-#else /* __ASSEMBLY__ */
-
- .macro cfe_early_init
-#ifdef CONFIG_CFE
- jal cfe_setup
-#endif
- .endm
-
-#endif /* __ASSEMBLY__ */
-#endif /* LINUX_CFE_PRIVATE_H_ */
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2002 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-#include <linux/init.h>
-#include <linux/types.h>
-#include <linux/pci.h>
-
-#include <bcmpci.h>
-#include <bcm_intr.h>
-#include <bcm_map_part.h>
-#include <6348_intr.h>
-#include <6348_map_part.h>
-
-static volatile MpiRegisters * mpi = (MpiRegisters *)(MPI_BASE);
-
-static char irq_tab_bcm96348[] __initdata = {
- [0] = INTERRUPT_ID_MPI,
- [1] = INTERRUPT_ID_MPI,
-#if defined(CONFIG_USB)
- [USB_HOST_SLOT] = INTERRUPT_ID_USBH
-#endif
-};
-
-int __init pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
- return irq_tab_bcm96348[slot];
-}
-
-static void bcm96348_fixup(struct pci_dev *dev)
-{
- uint32 memaddr;
- uint32 size;
-
- memaddr = pci_resource_start(dev, 0);
- size = pci_resource_len(dev, 0);
-
- switch (PCI_SLOT(dev->devfn)) {
- case 0:
- // UBUS to PCI address range
- // Memory Window 1. Mask determines which bits are decoded.
- mpi->l2pmrange1 = ~(size-1);
- // UBUS to PCI Memory base address. This is akin to the ChipSelect base
- // register.
- mpi->l2pmbase1 = memaddr & BCM_PCI_ADDR_MASK;
- // UBUS to PCI Remap Address. Replaces the masked address bits in the
- // range register with this setting.
- // Also, enable direct I/O and direct Memory accesses
- mpi->l2pmremap1 = (memaddr | MEM_WINDOW_EN);
- break;
-
- case 1:
- // Memory Window 2
- mpi->l2pmrange2 = ~(size-1);
- // UBUS to PCI Memory base address.
- mpi->l2pmbase2 = memaddr & BCM_PCI_ADDR_MASK;
- // UBUS to PCI Remap Address
- mpi->l2pmremap2 = (memaddr | MEM_WINDOW_EN);
- break;
-
-#if defined(CONFIG_USB)
- case USB_HOST_SLOT:
- dev->resource[0].start = USB_HOST_BASE;
- dev->resource[0].end = USB_HOST_BASE+USB_BAR0_MEM_SIZE-1;
- break;
-#endif
- }
-}
-
-int pcibios_plat_dev_init(struct pci_dev *dev)
-{
- return 0;
-}
-
-DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, PCI_ANY_ID,
- bcm96348_fixup);
-
-/*struct pci_fixup pcibios_fixups[] = {
- { PCI_FIXUP_FINAL, PCI_ANY_ID, PCI_ANY_ID, bcm96348_fixup },
- {0}
-};*/
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2002 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <asm/addrspace.h>
-
-#include <bcm_intr.h>
-#include <bcm_map_part.h>
-#include <6348_intr.h>
-#include <6348_map_part.h>
-#include <bcmpci.h>
-
-#include <linux/delay.h>
-
-#if defined(CONFIG_USB)
-#if 0
-#define DPRINT(x...) printk(x)
-#else
-#define DPRINT(x...)
-#endif
-
-static int
-pci63xx_int_read(unsigned int devfn, int where, u32 * value, int size);
-static int
-pci63xx_int_write(unsigned int devfn, int where, u32 * value, int size);
-
-static bool usb_mem_size_rd = FALSE;
-static uint32 usb_mem_base = 0;
-static uint32 usb_cfg_space_cmd_reg = 0;
-#endif
-static bool pci_mem_size_rd = FALSE;
-
-static volatile MpiRegisters * mpi = (MpiRegisters *)(MPI_BASE);
-
-static void mpi_SetupPciConfigAccess(uint32 addr)
-{
- mpi->l2pcfgctl = (DIR_CFG_SEL | DIR_CFG_USEREG | addr) & ~CONFIG_TYPE;
-}
-
-static void mpi_ClearPciConfigAccess(void)
-{
- mpi->l2pcfgctl = 0x00000000;
-}
-
-#if defined(CONFIG_USB)
-/* --------------------------------------------------------------------------
- Name: pci63xx_int_write
-Abstract: PCI Config write on internal device(s)
- -------------------------------------------------------------------------- */
-static int
-pci63xx_int_write(unsigned int devfn, int where, u32 * value, int size)
-{
- if (PCI_SLOT(devfn) != USB_HOST_SLOT) {
- return PCIBIOS_SUCCESSFUL;
- }
-
- switch (size) {
- case 1:
- DPRINT("W => Slot: %d Where: %2X Len: %d Data: %02X\n",
- PCI_SLOT(devfn), where, size, *value);
- break;
- case 2:
- DPRINT("W => Slot: %d Where: %2X Len: %d Data: %04X\n",
- PCI_SLOT(devfn), where, size, *value);
- switch (where) {
- case PCI_COMMAND:
- usb_cfg_space_cmd_reg = *value;
- break;
- default:
- break;
- }
- break;
- case 4:
- DPRINT("W => Slot: %d Where: %2X Len: %d Data: %08lX\n",
- PCI_SLOT(devfn), where, size, *value);
- switch (where) {
- case PCI_BASE_ADDRESS_0:
- if (*value == 0xffffffff) {
- usb_mem_size_rd = TRUE;
- } else {
- usb_mem_base = *value;
- }
- break;
- default:
- break;
- }
- break;
- default:
- break;
- }
-
- return PCIBIOS_SUCCESSFUL;
-}
-
-/* --------------------------------------------------------------------------
- Name: pci63xx_int_read
-Abstract: PCI Config read on internal device(s)
- -------------------------------------------------------------------------- */
-static int
-pci63xx_int_read(unsigned int devfn, int where, u32 * value, int size)
-{
- uint32 retValue = 0xFFFFFFFF;
-
- if (PCI_SLOT(devfn) != USB_HOST_SLOT) {
- return PCIBIOS_SUCCESSFUL;
- }
-
- // For now, this is specific to the USB Host controller. We can
- // make it more general if we have to...
- // Emulate PCI Config accesses
- switch (where) {
- case PCI_VENDOR_ID:
- case PCI_DEVICE_ID:
- retValue = PCI_VENDOR_ID_BROADCOM | 0x63000000;
- break;
- case PCI_COMMAND:
- case PCI_STATUS:
- retValue = (0x0006 << 16) | usb_cfg_space_cmd_reg;
- break;
- case PCI_CLASS_REVISION:
- case PCI_CLASS_DEVICE:
- retValue = (PCI_CLASS_SERIAL_USB << 16) | (0x10 << 8) | 0x01;
- break;
- case PCI_BASE_ADDRESS_0:
- if (usb_mem_size_rd) {
- retValue = USB_BAR0_MEM_SIZE;
- } else {
- if (usb_mem_base != 0)
- retValue = usb_mem_base;
- else
- retValue = USB_HOST_BASE;
- }
- usb_mem_size_rd = FALSE;
- break;
- case PCI_CACHE_LINE_SIZE:
- case PCI_LATENCY_TIMER:
- retValue = 0;
- break;
- case PCI_HEADER_TYPE:
- retValue = PCI_HEADER_TYPE_NORMAL;
- break;
- case PCI_SUBSYSTEM_VENDOR_ID:
- retValue = PCI_VENDOR_ID_BROADCOM;
- break;
- case PCI_SUBSYSTEM_ID:
- retValue = 0x6300;
- break;
- case PCI_INTERRUPT_LINE:
- retValue = INTERRUPT_ID_USBH;
- break;
- default:
- break;
- }
-
- switch (size) {
- case 1:
- *value = (retValue >> ((where & 3) << 3)) & 0xff;
- DPRINT("R <= Slot: %d Where: %2X Len: %d Data: %02X\n",
- PCI_SLOT(devfn), where, size, *value);
- break;
- case 2:
- *value = (retValue >> ((where & 3) << 3)) & 0xffff;
- DPRINT("R <= Slot: %d Where: %2X Len: %d Data: %04X\n",
- PCI_SLOT(devfn), where, size, *value);
- break;
- case 4:
- *value = retValue;
- DPRINT("R <= Slot: %d Where: %2X Len: %d Data: %08lX\n",
- PCI_SLOT(devfn), where, size, *value);
- break;
- default:
- break;
- }
-
- return PCIBIOS_SUCCESSFUL;
-}
-#endif
-
-static int bcm96348_pcibios_read(struct pci_bus *bus, unsigned int devfn,
- int where, int size, u32 * val)
-{
- volatile unsigned char *ioBase = (unsigned char *)(mpi->l2piobase | KSEG1);
- uint32 data;
-
-#if defined(CONFIG_USB)
- if (PCI_SLOT(devfn) == USB_HOST_SLOT)
- return pci63xx_int_read(devfn, where, val, size);
-#endif
-
- mpi_SetupPciConfigAccess(BCM_PCI_CFG(PCI_SLOT(devfn), PCI_FUNC(devfn), where));
- data = *(uint32 *)ioBase;
- switch(size) {
- case 1:
- *val = (data >> ((where & 3) << 3)) & 0xff;
- break;
- case 2:
- *val = (data >> ((where & 3) << 3)) & 0xffff;
- break;
- case 4:
- *val = data;
- /* Special case for reading PCI device range */
- if ((where >= PCI_BASE_ADDRESS_0) && (where <= PCI_BASE_ADDRESS_5)) {
- if (pci_mem_size_rd) {
- /* bcm6348 PCI memory window minimum size is 64K */
- *val &= PCI_SIZE_64K;
- }
- }
- break;
- default:
- break;
- }
- pci_mem_size_rd = FALSE;
- mpi_ClearPciConfigAccess();
-
- return PCIBIOS_SUCCESSFUL;
-}
-
-static int bcm96348_pcibios_write(struct pci_bus *bus, unsigned int devfn,
- int where, int size, u32 val)
-{
- volatile unsigned char *ioBase = (unsigned char *)(mpi->l2piobase | KSEG1);
- uint32 data;
-
-#if defined(CONFIG_USB)
- if (PCI_SLOT(devfn) == USB_HOST_SLOT)
- return pci63xx_int_write(devfn, where, &val, size);
-#endif
- mpi_SetupPciConfigAccess(BCM_PCI_CFG(PCI_SLOT(devfn), PCI_FUNC(devfn), where));
- data = *(uint32 *)ioBase;
- switch(size) {
- case 1:
- data = (data & ~(0xff << ((where & 3) << 3))) |
- (val << ((where & 3) << 3));
- break;
- case 2:
- data = (data & ~(0xffff << ((where & 3) << 3))) |
- (val << ((where & 3) << 3));
- break;
- case 4:
- data = val;
- /* Special case for reading PCI device range */
- if ((where >= PCI_BASE_ADDRESS_0) && (where <= PCI_BASE_ADDRESS_5)) {
- if (val == 0xffffffff)
- pci_mem_size_rd = TRUE;
- }
- break;
- default:
- break;
- }
- *(uint32 *)ioBase = data;
- udelay(500);
- mpi_ClearPciConfigAccess();
-
- return PCIBIOS_SUCCESSFUL;
-}
-
-struct pci_ops bcm96348_pci_ops = {
- .read = bcm96348_pcibios_read,
- .write = bcm96348_pcibios_write
-};
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2002 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-
-#include <bcmpci.h>
-
-static struct resource bcm_pci_io_resource = {
- .name = "bcm96348 pci IO space",
- .start = BCM_PCI_IO_BASE,
- .end = BCM_PCI_IO_BASE + BCM_PCI_IO_SIZE_64KB - 1,
- .flags = IORESOURCE_IO
-};
-
-static struct resource bcm_pci_mem_resource = {
- .name = "bcm96348 pci memory space",
- .start = BCM_PCI_MEM_BASE,
- .end = BCM_PCI_MEM_BASE + BCM_PCI_MEM_SIZE_16MB - 1,
- .flags = IORESOURCE_MEM
-};
-
-extern struct pci_ops bcm96348_pci_ops;
-
-struct pci_controller bcm96348_controller = {
- .pci_ops = &bcm96348_pci_ops,
- .io_resource = &bcm_pci_io_resource,
- .mem_resource = &bcm_pci_mem_resource,
-};
-
-static __init int bcm96348_pci_init(void)
-{
- /* Avoid ISA compat ranges. */
- PCIBIOS_MIN_IO = 0x00000000;
- PCIBIOS_MIN_MEM = 0x00000000;
-
- /* Set I/O resource limits. */
- ioport_resource.end = 0x1fffffff;
- iomem_resource.end = 0xffffffff;
-
- register_pci_controller(&bcm96348_controller);
- return 0;
-}
-
-arch_initcall(bcm96348_pci_init);
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2002 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-
-/* Description: Serial port driver for the BCM963XX. */
-
-#define CARDNAME "bcm963xx_serial driver"
-#define VERSION "2.0"
-#define VER_STR CARDNAME " v" VERSION "\n"
-
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/version.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/spinlock.h>
-
-/* for definition of struct console */
-#include <linux/console.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/serial.h>
-#include <linux/serialP.h>
-#include <asm/uaccess.h>
-
-#include <bcmtypes.h>
-#include <board.h>
-#include <bcm_map_part.h>
-#include <bcm_intr.h>
-#include <6348_map_part.h>
-#include <6348_intr.h>
-
-static DEFINE_SPINLOCK(bcm963xx_serial_lock);
-
-extern void _putc(char);
-extern void _puts(const char *);
-
-typedef struct bcm_serial {
- volatile Uart *port;
- int type;
- int flags;
- int irq;
- int baud_base;
- int blocked_open;
- unsigned short close_delay;
- unsigned short closing_wait;
- unsigned short line; /* port/line number */
- unsigned short cflags; /* line configuration flag */
- unsigned short x_char; /* xon/xoff character */
- unsigned short read_status_mask; /* mask for read condition */
- unsigned short ignore_status_mask; /* mask for ignore condition */
- unsigned long event; /* mask used in BH */
- int xmit_head; /* Position of the head */
- int xmit_tail; /* Position of the tail */
- int xmit_cnt; /* Count of the chars in the buffer */
- int count; /* indicates how many times it has been opened */
- int magic;
-
- struct async_icount icount; /* keep track of things ... */
- struct tty_struct *tty; /* tty associated */
- struct ktermios normal_termios;
-
- wait_queue_head_t open_wait;
- wait_queue_head_t close_wait;
-
- long session; /* Session of opening process */
- long pgrp; /* pgrp of opening process */
-
- unsigned char is_initialized;
-} Context;
-
-
-/*---------------------------------------------------------------------*/
-/* Define bits in the Interrupt Enable register */
-/*---------------------------------------------------------------------*/
-/* Enable receive interrupt */
-#define RXINT (RXFIFONE|RXOVFERR)
-
-/* Enable transmit interrupt */
-#define TXINT (TXFIFOEMT|TXUNDERR|TXOVFERR)
-
-/* Enable receiver line status interrupt */
-#define LSINT (RXBRK|RXPARERR|RXFRAMERR)
-
-#define BCM_NUM_UARTS 1
-
-#define BD_BCM63XX_TIMER_CLOCK_INPUT (FPERIPH)
-
-
-static struct bcm_serial multi[BCM_NUM_UARTS];
-static struct bcm_serial *lines[BCM_NUM_UARTS];
-static struct tty_driver *serial_driver;
-static struct ktermios *serial_termios[BCM_NUM_UARTS];
-static struct ktermios *serial_termios_locked[BCM_NUM_UARTS];
-
-
-static void bcm_stop(struct tty_struct *tty);
-static void bcm_start(struct tty_struct *tty);
-static inline void receive_chars(struct bcm_serial *info);
-static int startup(struct bcm_serial *info);
-static void shutdown(struct bcm_serial *info);
-static void change_speed(volatile Uart * pUart, tcflag_t cFlag);
-static void bcm63xx_cons_flush_chars(struct tty_struct *tty);
-static int bcm63xx_cons_write(struct tty_struct *tty,
- const unsigned char *buf, int count);
-static int bcm63xx_cons_write_room(struct tty_struct *tty);
-static int bcm_chars_in_buffer(struct tty_struct *tty);
-static void bcm_flush_buffer(struct tty_struct *tty);
-static void bcm_throttle(struct tty_struct *tty);
-static void bcm_unthrottle(struct tty_struct *tty);
-static void bcm_send_xchar(struct tty_struct *tty, char ch);
-static int get_serial_info(struct bcm_serial *info,
- struct serial_struct *retinfo);
-static int set_serial_info(struct bcm_serial *info,
- struct serial_struct *new_info);
-static int get_lsr_info(struct bcm_serial *info, unsigned int *value);
-static void send_break(struct bcm_serial *info, int duration);
-static int bcm_ioctl(struct tty_struct *tty, struct file *file,
- unsigned int cmd, unsigned long arg);
-static void bcm_set_termios(struct tty_struct *tty,
- struct ktermios *old_termios);
-static void bcm63xx_cons_close(struct tty_struct *tty, struct file *filp);
-static void bcm_hangup(struct tty_struct *tty);
-static int block_til_ready(struct tty_struct *tty, struct file *filp,
- struct bcm_serial *info);
-static int bcm63xx_cons_open(struct tty_struct *tty, struct file *filp);
-static int __init bcm63xx_serialinit(void);
-
-
-/*
- * ------------------------------------------------------------
- * rs_stop () and rs_start ()
- *
- * These routines are called before setting or resetting
- * tty->stopped. They enable or disable transmitter interrupts,
- * as necessary.
- * ------------------------------------------------------------
- */
-static void bcm_stop(struct tty_struct *tty)
-{
-}
-
-static void bcm_start(struct tty_struct *tty)
-{
- _puts(CARDNAME " Start\n");
-}
-
-/*
- * ------------------------------------------------------------
- * receive_char ()
- *
- * This routine deals with inputs from any lines.
- * ------------------------------------------------------------
- */
-static inline void receive_chars(struct bcm_serial *info)
-{
- struct tty_struct *tty = 0;
- struct async_icount *icount;
- int ignore = 0;
- unsigned short status, tmp;
- UCHAR ch = 0;
- while ((status = info->port->intStatus) & RXINT) {
- char flag_char = TTY_NORMAL;
-
- if (status & RXFIFONE)
- ch = info->port->Data; // Read the character
- tty = info->tty; /* now tty points to the proper dev */
- icount = &info->icount;
- if (!tty)
- break;
- if (!tty_buffer_request_room(tty, 1))
- break;
- icount->rx++;
- if (status & RXBRK) {
- flag_char = TTY_BREAK;
- icount->brk++;
- }
- // keep track of the statistics
- if (status & (RXFRAMERR | RXPARERR | RXOVFERR)) {
- if (status & RXPARERR) /* parity error */
- icount->parity++;
- else if (status & RXFRAMERR) /* frame error */
- icount->frame++;
- if (status & RXOVFERR) {
- // Overflow. Reset the RX FIFO
- info->port->fifoctl |= RSTRXFIFOS;
- icount->overrun++;
- }
- // check to see if we should ignore the character
- // and mask off conditions that should be ignored
- if (status & info->ignore_status_mask) {
- if (++ignore > 100)
- break;
- goto ignore_char;
- }
- // Mask off the error conditions we want to ignore
- tmp = status & info->read_status_mask;
- if (tmp & RXPARERR) {
- flag_char = TTY_PARITY;
- } else if (tmp & RXFRAMERR) {
- flag_char = TTY_FRAME;
- }
- if (tmp & RXOVFERR) {
- tty_insert_flip_char(tty, ch, flag_char);
- ch = 0;
- flag_char = TTY_OVERRUN;
- if (!tty_buffer_request_room(tty, 1))
- break;
- }
- }
- tty_insert_flip_char(tty, ch, flag_char);
- }
- ignore_char:;
- tty_flip_buffer_push(tty);
- tty_schedule_flip(tty);
-
-}
-
-
-/*
- * ------------------------------------------------------------
- * bcm_interrupt ()
- *
- * this is the main interrupt routine for the chip.
- * It deals with the multiple ports.
- * ------------------------------------------------------------
- */
-#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
-static irqreturn_t bcm_interrupt(int irq, void *dev)
-#else
-static void bcm_interrupt(int irq, void *dev, struct pt_regs *regs)
-#endif
-{
- struct bcm_serial *info = lines[0];
- UINT16 intStat;
-
- /* get pending interrupt flags from UART */
-
- /* Mask with only the serial interrupts that are enabled */
- intStat = info->port->intStatus & info->port->intMask;
- while (intStat) {
- if (intStat & RXINT)
- receive_chars(info);
- else if (intStat & TXINT)
- info->port->intStatus = TXINT;
- else /* don't know what it was, so let's mask it */
- info->port->intMask &= ~intStat;
-
- intStat = info->port->intStatus & info->port->intMask;
- }
-
- // Clear the interrupt
- enable_brcm_irq(INTERRUPT_ID_UART);
-#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
- return IRQ_HANDLED;
-#endif
-}
-
-/*
- * -------------------------------------------------------------------
- * startup ()
- *
- * various initialization tasks
- * -------------------------------------------------------------------
- */
-static int startup(struct bcm_serial *info)
-{
- // Port is already started...
- return 0;
-}
-
-/*
- * -------------------------------------------------------------------
- * shutdown ()
- *
- * This routine will shutdown a serial port; interrupts are disabled, and
- * DTR is dropped if the hangup on close termio flag is on.
- * -------------------------------------------------------------------
- */
-static void shutdown(struct bcm_serial *info)
-{
- unsigned long flags;
- if (!info->is_initialized)
- return;
-
- spin_lock_irqsave(&bcm963xx_serial_lock, flags);
-
- info->port->control &= ~(BRGEN | TXEN | RXEN);
- if (info->tty)
- set_bit(TTY_IO_ERROR, &info->tty->flags);
- info->is_initialized = 0;
-
- spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
-}
-
-/*
- * -------------------------------------------------------------------
- * change_speed ()
- *
- * Set the baud rate, character size, parity and stop bits.
- * -------------------------------------------------------------------
- */
-static void change_speed(volatile Uart * pUart, tcflag_t cFlag)
-{
- unsigned long ulFlags, ulBaud, ulClockFreqHz, ulTmp;
-
- spin_lock_irqsave(&bcm963xx_serial_lock, ulFlags);
- switch (cFlag & (CBAUD | CBAUDEX)) {
- case B115200:
- ulBaud = 115200;
- break;
- case B57600:
- ulBaud = 57600;
- break;
- case B38400:
- ulBaud = 38400;
- break;
- case B19200:
- ulBaud = 19200;
- break;
- case B9600:
- ulBaud = 9600;
- break;
- case B4800:
- ulBaud = 4800;
- break;
- case B2400:
- ulBaud = 2400;
- break;
- case B1800:
- ulBaud = 1800;
- break;
- case B1200:
- ulBaud = 1200;
- break;
- case B600:
- ulBaud = 600;
- break;
- case B300:
- ulBaud = 300;
- break;
- case B200:
- ulBaud = 200;
- break;
- case B150:
- ulBaud = 150;
- break;
- case B134:
- ulBaud = 134;
- break;
- case B110:
- ulBaud = 110;
- break;
- case B75:
- ulBaud = 75;
- break;
- case B50:
- ulBaud = 50;
- break;
- default:
- ulBaud = 115200;
- break;
- }
-
- /* Calculate buad rate. */
- ulClockFreqHz = BD_BCM63XX_TIMER_CLOCK_INPUT;
- ulTmp = (ulClockFreqHz / ulBaud) / 16;
- if (ulTmp & 0x01)
- ulTmp /= 2; /* Rounding up, so sub is already accounted for */
- else
- ulTmp = (ulTmp / 2) - 1; /* Rounding down so we must sub 1 */
- pUart->baudword = ulTmp;
-
- /* Set character size, stop bits and parity. */
- switch (cFlag & CSIZE) {
- case CS5:
- ulTmp = BITS5SYM; /* select transmit 5 bit data size */
- break;
- case CS6:
- ulTmp = BITS6SYM; /* select transmit 6 bit data size */
- break;
- case CS7:
- ulTmp = BITS7SYM; /* select transmit 7 bit data size */
- break;
- default:
- ulTmp = BITS8SYM; /* select transmit 8 bit data size */
- break;
- }
- if (cFlag & CSTOPB)
- ulTmp |= TWOSTOP; /* select 2 stop bits */
- else
- ulTmp |= ONESTOP; /* select one stop bit */
-
- /* Write these values into the config reg. */
- pUart->config = ulTmp;
- pUart->control &=
- ~(RXPARITYEN | TXPARITYEN | RXPARITYEVEN | TXPARITYEVEN);
- switch (cFlag & (PARENB | PARODD)) {
- case PARENB | PARODD:
- pUart->control |= RXPARITYEN | TXPARITYEN;
- break;
- case PARENB:
- pUart->control |=
- RXPARITYEN | TXPARITYEN | RXPARITYEVEN | TXPARITYEVEN;
- break;
- default:
- pUart->control |= 0;
- break;
- }
-
- /* Reset and flush uart */
- pUart->fifoctl = RSTTXFIFOS | RSTRXFIFOS;
- spin_unlock_irqrestore(&bcm963xx_serial_lock, ulFlags);
-}
-
-
-/*
- * -------------------------------------------------------------------
- * bcm_flush_char ()
- *
- * Nothing to flush. Polled I/O is used.
- * -------------------------------------------------------------------
- */
-static void bcm63xx_cons_flush_chars(struct tty_struct *tty)
-{
-}
-
-
-/*
- * -------------------------------------------------------------------
- * bcm63xx_cons_write ()
- *
- * Main output routine using polled I/O.
- * -------------------------------------------------------------------
- */
-static int bcm63xx_cons_write(struct tty_struct *tty,
- const unsigned char *buf, int count)
-{
- int c;
-
- for (c = 0; c < count; c++)
- _putc(buf[c]);
- return count;
-}
-
-/*
- * -------------------------------------------------------------------
- * bcm63xx_cons_write_room ()
- *
- * Compute the amount of space available for writing.
- * -------------------------------------------------------------------
- */
-static int bcm63xx_cons_write_room(struct tty_struct *tty)
-{
- /* Pick a number. Any number. Polled I/O is used. */
- return 1024;
-}
-
-/*
- * -------------------------------------------------------------------
- * bcm_chars_in_buffer ()
- *
- * compute the amount of char left to be transmitted
- * -------------------------------------------------------------------
- */
-static int bcm_chars_in_buffer(struct tty_struct *tty)
-{
- return 0;
-}
-
-/*
- * -------------------------------------------------------------------
- * bcm_flush_buffer ()
- *
- * Empty the output buffer
- * -------------------------------------------------------------------
- */
-static void bcm_flush_buffer(struct tty_struct *tty)
-{
- tty_wakeup(tty);
-}
-
-/*
- * ------------------------------------------------------------
- * bcm_throttle () and bcm_unthrottle ()
- *
- * This routine is called by the upper-layer tty layer to signal that
- * incoming characters should be throttled (or not).
- * ------------------------------------------------------------
- */
-static void bcm_throttle(struct tty_struct *tty)
-{
- struct bcm_serial *info = (struct bcm_serial *) tty->driver_data;
- if (I_IXOFF(tty))
- info->x_char = STOP_CHAR(tty);
-}
-
-static void bcm_unthrottle(struct tty_struct *tty)
-{
- struct bcm_serial *info = (struct bcm_serial *) tty->driver_data;
- if (I_IXOFF(tty)) {
- if (info->x_char)
- info->x_char = 0;
- else
- info->x_char = START_CHAR(tty);
- }
-}
-
-static void bcm_send_xchar(struct tty_struct *tty, char ch)
-{
- struct bcm_serial *info = (struct bcm_serial *) tty->driver_data;
- info->x_char = ch;
- if (ch)
- bcm_start(info->tty);
-}
-
-/*
- * ------------------------------------------------------------
- * rs_ioctl () and friends
- * ------------------------------------------------------------
- */
-static int get_serial_info(struct bcm_serial *info,
- struct serial_struct *retinfo)
-{
- struct serial_struct tmp;
-
- if (!retinfo)
- return -EFAULT;
-
- memset(&tmp, 0, sizeof(tmp));
- tmp.type = info->type;
- tmp.line = info->line;
- tmp.port = (int) info->port;
- tmp.irq = info->irq;
- tmp.flags = 0;
- tmp.baud_base = info->baud_base;
- tmp.close_delay = info->close_delay;
- tmp.closing_wait = info->closing_wait;
-
- return copy_to_user(retinfo, &tmp, sizeof(*retinfo));
-}
-
-static int set_serial_info(struct bcm_serial *info,
- struct serial_struct *new_info)
-{
- struct serial_struct new_serial;
- struct bcm_serial old_info;
- int retval = 0;
-
- if (!new_info)
- return -EFAULT;
-
- copy_from_user(&new_serial, new_info, sizeof(new_serial));
- old_info = *info;
-
- if (!capable(CAP_SYS_ADMIN))
- return -EPERM;
-
-
- if (info->count > 1)
- return -EBUSY;
-
- /* OK, past this point, all the error checking has been done.
- * At this point, we start making changes.....
- */
- info->baud_base = new_serial.baud_base;
- info->type = new_serial.type;
- info->close_delay = new_serial.close_delay;
- info->closing_wait = new_serial.closing_wait;
- retval = startup(info);
- return retval;
-}
-
-/*
- * get_lsr_info - get line status register info
- *
- * Purpose: Let user call ioctl() to get info when the UART physically
- * is emptied. On bus types like RS485, the transmitter must
- * release the bus after transmitting. This must be done when
- * the transmit shift register is empty, not be done when the
- * transmit holding register is empty. This functionality
- * allows an RS485 driver to be written in user space.
- */
-static int get_lsr_info(struct bcm_serial *info, unsigned int *value)
-{
- return (0);
-}
-
-/*
- * This routine sends a break character out the serial port.
- */
-static void send_break(struct bcm_serial *info, int duration)
-{
- unsigned long flags;
-
- if (!info->port)
- return;
-
- current->state = TASK_INTERRUPTIBLE;
-
- /*save_flags (flags);
- cli(); */
- spin_lock_irqsave(&bcm963xx_serial_lock, flags);
-
- info->port->control |= XMITBREAK;
- schedule_timeout(duration);
- info->port->control &= ~XMITBREAK;
-
- spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
- //restore_flags (flags);
-}
-
-static int bcm_ioctl(struct tty_struct *tty, struct file *file,
- unsigned int cmd, unsigned long arg)
-{
- int error;
- struct bcm_serial *info = (struct bcm_serial *) tty->driver_data;
- int retval;
-
- if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
- (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGWILD) &&
- (cmd != TIOCSERSWILD) && (cmd != TIOCSERGSTRUCT)) {
- if (tty->flags & (1 << TTY_IO_ERROR))
- return -EIO;
- }
- switch (cmd) {
-
- case TCSBRK: /* SVID version: non-zero arg --> no break */
- retval = tty_check_change(tty);
- if (retval)
- return retval;
- tty_wait_until_sent(tty, 0);
- if (!arg)
- send_break(info, HZ / 4); /* 1/4 second */
- return 0;
-
- case TCSBRKP: /* support for POSIX tcsendbreak() */
- retval = tty_check_change(tty);
- if (retval)
- return retval;
- tty_wait_until_sent(tty, 0);
- send_break(info, arg ? arg * (HZ / 10) : HZ / 4);
- return 0;
-
- case TIOCGSOFTCAR:
- error =
- access_ok(VERIFY_WRITE, (void *) arg, sizeof(long));
- if (!error)
- return -EFAULT;
- else {
- put_user(C_CLOCAL(tty) ? 1 : 0,
- (unsigned long *) arg);
- return 0;
- }
-
- case TIOCSSOFTCAR:
- error = get_user(arg, (unsigned long *) arg);
- if (error)
- return error;
- tty->termios->c_cflag =
- ((tty->termios->
- c_cflag & ~CLOCAL) | (arg ? CLOCAL : 0));
- return 0;
-
- case TIOCGSERIAL:
- error =
- access_ok(VERIFY_WRITE, (void *) arg,
- sizeof(struct serial_struct));
- if (!error)
- return -EFAULT;
- else
- return get_serial_info(info,
- (struct serial_struct *)
- arg);
-
- case TIOCSSERIAL:
- return set_serial_info(info, (struct serial_struct *) arg);
-
- case TIOCSERGETLSR: /* Get line status register */
- error =
- access_ok(VERIFY_WRITE, (void *) arg,
- sizeof(unsigned int));
- if (!error)
- return -EFAULT;
- else
- return get_lsr_info(info, (unsigned int *) arg);
-
- case TIOCSERGSTRUCT:
- error =
- access_ok(VERIFY_WRITE, (void *) arg,
- sizeof(struct bcm_serial));
- if (!error)
- return -EFAULT;
- else {
- copy_to_user((struct bcm_serial *) arg, info,
- sizeof(struct bcm_serial));
- return 0;
- }
-
- default:
- return -ENOIOCTLCMD;
- }
- return 0;
-}
-
-static void bcm_set_termios(struct tty_struct *tty,
- struct ktermios *old_termios)
-{
- struct bcm_serial *info = (struct bcm_serial *) tty->driver_data;
-
- if (tty->termios->c_cflag != old_termios->c_cflag)
- change_speed(info->port, tty->termios->c_cflag);
-}
-
-/*
- * ------------------------------------------------------------
- * bcm63xx_cons_close()
- *
- * This routine is called when the serial port gets closed. First, we
- * wait for the last remaining data to be sent. Then, we turn off
- * the transmit enable and receive enable flags.
- * ------------------------------------------------------------
- */
-static void bcm63xx_cons_close(struct tty_struct *tty, struct file *filp)
-{
- struct bcm_serial *info = (struct bcm_serial *) tty->driver_data;
- unsigned long flags;
-
- if (!info)
- return;
-
- /*save_flags (flags);
- cli(); */
- spin_lock_irqsave(&bcm963xx_serial_lock, flags);
-
- if (tty_hung_up_p(filp)) {
- spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
- //restore_flags (flags);
- return;
- }
-
- if ((tty->count == 1) && (info->count != 1)) {
-
- /* Uh, oh. tty->count is 1, which means that the tty
- * structure will be freed. Info->count should always
- * be one in these conditions. If it's greater than
- * one, we've got real problems, since it means the
- * serial port won't be shutdown.
- */
- printk
- ("bcm63xx_cons_close: bad serial port count; tty->count is 1, "
- "info->count is %d\n", info->count);
- info->count = 1;
- }
-
- if (--info->count < 0) {
- printk("ds_close: bad serial port count for ttys%d: %d\n",
- info->line, info->count);
- info->count = 0;
- }
-
- if (info->count) {
- //restore_flags (flags);
- spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
- return;
- }
-
- /* Now we wait for the transmit buffer to clear; and we notify
- * the line discipline to only process XON/XOFF characters.
- */
- tty->closing = 1;
-
- /* At this point we stop accepting input. To do this, we
- * disable the receive line status interrupts.
- */
- shutdown(info);
-#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
- if (tty->driver->flush_buffer)
- tty->driver->flush_buffer(tty);
-#else
- if (tty->driver.flush_buffer)
- tty->driver.flush_buffer(tty);
-#endif
- if (tty->ldisc.flush_buffer)
- tty->ldisc.flush_buffer(tty);
-
- tty->closing = 0;
- info->event = 0;
- info->tty = 0;
- if (tty->ldisc.num != tty_ldisc_get(N_TTY)->num) {
- if (tty->ldisc.close)
- (tty->ldisc.close) (tty);
- tty->ldisc = *tty_ldisc_get(N_TTY);
- tty->termios->c_line = N_TTY;
- if (tty->ldisc.open)
- (tty->ldisc.open) (tty);
- }
- if (info->blocked_open) {
- if (info->close_delay) {
- current->state = TASK_INTERRUPTIBLE;
- schedule_timeout(info->close_delay);
- }
- wake_up_interruptible(&info->open_wait);
- }
- wake_up_interruptible(&info->close_wait);
-
- //restore_flags (flags);
- spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
-}
-
-/*
- * bcm_hangup () --- called by tty_hangup() when a hangup is signaled.
- */
-static void bcm_hangup(struct tty_struct *tty)
-{
-
- struct bcm_serial *info = (struct bcm_serial *) tty->driver_data;
-
- shutdown(info);
- info->event = 0;
- info->count = 0;
- info->tty = 0;
- wake_up_interruptible(&info->open_wait);
-}
-
-/*
- * ------------------------------------------------------------
- * rs_open() and friends
- * ------------------------------------------------------------
- */
-static int block_til_ready(struct tty_struct *tty, struct file *filp,
- struct bcm_serial *info)
-{
- return 0;
-}
-
-/*
- * This routine is called whenever a serial port is opened. It
- * enables interrupts for a serial port. It also performs the
- * serial-specific initialization for the tty structure.
- */
-static int bcm63xx_cons_open(struct tty_struct *tty, struct file *filp)
-{
- struct bcm_serial *info;
- int retval, line;
-
- // Make sure we're only opening on of the ports we support
-#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
- line = MINOR(tty->driver->cdev.dev) - tty->driver->minor_start;
-#else
- line = MINOR(tty->device) - tty->driver.minor_start;
-#endif
-
- if ((line < 0) || (line >= BCM_NUM_UARTS))
- return -ENODEV;
-
- info = lines[line];
-
- tty->low_latency = 1;
- info->port->intMask = 0; /* Clear any pending interrupts */
- info->port->intMask = RXINT; /* Enable RX */
-
- info->count++;
- tty->driver_data = info;
- info->tty = tty;
- enable_brcm_irq(INTERRUPT_ID_UART);
-
- // Start up serial port
- retval = startup(info);
- if (retval)
- return retval;
-
- retval = block_til_ready(tty, filp, info);
- if (retval)
- return retval;
-
-
-#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
- info->pgrp = task_pgrp(current);
-#else
- info->session = current->session;
- info->pgrp = current->pgrp;
-#endif
-
- return 0;
-}
-
-
-static struct tty_operations rs_ops = {
- .open = bcm63xx_cons_open,
- .close = bcm63xx_cons_close,
- .write = bcm63xx_cons_write,
- .flush_chars = bcm63xx_cons_flush_chars,
- .write_room = bcm63xx_cons_write_room,
- .chars_in_buffer = bcm_chars_in_buffer,
- .flush_buffer = bcm_flush_buffer,
- .ioctl = bcm_ioctl,
- .throttle = bcm_throttle,
- .unthrottle = bcm_unthrottle,
- .send_xchar = bcm_send_xchar,
- .set_termios = bcm_set_termios,
- .stop = bcm_stop,
- .start = bcm_start,
- .hangup = bcm_hangup,
-};
-
-/* --------------------------------------------------------------------------
- Name: bcm63xx_serialinit
- Purpose: Initialize our BCM63xx serial driver
--------------------------------------------------------------------------- */
-static int __init bcm63xx_serialinit(void)
-{
- int i, flags;
- struct bcm_serial *info;
-
- // Print the driver version information
- printk(VER_STR);
- serial_driver = alloc_tty_driver(BCM_NUM_UARTS);
- if (!serial_driver)
- return -ENOMEM;
-
- serial_driver->owner = THIS_MODULE;
- serial_driver->name = "ttyS";
- serial_driver->major = TTY_MAJOR;
- serial_driver->minor_start = 64;
- serial_driver->num = 1;
- serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
- serial_driver->subtype = SERIAL_TYPE_NORMAL;
- serial_driver->init_termios = tty_std_termios;
- serial_driver->init_termios.c_cflag = B115200 | CS8 | CREAD | HUPCL | CLOCAL;
- serial_driver->flags = TTY_DRIVER_REAL_RAW;
-
- serial_driver->termios = serial_termios;
- serial_driver->termios_locked = serial_termios_locked;
-
- tty_set_operations(serial_driver, &rs_ops);
-
- if (tty_register_driver(serial_driver))
- panic("Couldn't register serial driver\n");
-
- //save_flags(flags); cli();
- spin_lock_irqsave(&bcm963xx_serial_lock, flags);
-
- for (i = 0; i < 1; i++) {
- info = &multi[i];
- lines[i] = info;
- info->magic = SERIAL_MAGIC;
- info->port = (Uart *) ((char *) UART_BASE + (i * 0x20));
- info->tty = 0;
- info->irq = (2 - i) + 8;
- info->line = i;
- info->close_delay = 50;
- info->closing_wait = 3000;
- info->x_char = 0;
- info->event = 0;
- info->count = 0;
- info->blocked_open = 0;
- info->normal_termios = serial_driver->init_termios;
- init_waitqueue_head(&info->open_wait);
- init_waitqueue_head(&info->close_wait);
-
- /* If we are pointing to address zero then punt - not correctly
- * set up in setup.c to handle this.
- */
- if (!info->port)
- return 0;
- BcmHalMapInterrupt(bcm_interrupt, 0, INTERRUPT_ID_UART);
- }
-
- /* order matters here... the trick is that flags
- * is updated... in request_irq - to immediatedly obliterate
- * it is unwise.
- */
- spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
- return 0;
-}
-
-module_init(bcm63xx_serialinit);
-
-/* --------------------------------------------------------------------------
- Name: bcm_console_print
- Purpose: bcm_console_print is registered for printk.
- The console_lock must be held when we get here.
--------------------------------------------------------------------------- */
-static void bcm_console_print(struct console *cons, const char *str,
- unsigned int count)
-{
- unsigned int i;
- //_puts(str);
- for (i = 0; i < count; i++, str++) {
- _putc(*str);
- if (*str == 10) {
- _putc(13);
- }
- }
-}
-
-static struct tty_driver *bcm_console_device(struct console *c, int *index)
-{
- *index = c->index;
- return serial_driver;
-}
-
-static int __init bcm_console_setup(struct console *co, char *options)
-{
- return 0;
-}
-
-static struct console bcm_sercons = {
- .name = "ttyS",
- .write = bcm_console_print,
- .device = bcm_console_device,
- .setup = bcm_console_setup,
- .flags = CON_PRINTBUFFER,
- .index = -1,
-};
-
-static int __init bcm63xx_console_init(void)
-{
- register_console(&bcm_sercons);
- return 0;
-}
-
-console_initcall(bcm63xx_console_init);
+++ /dev/null
-/*
- * Broadcom Common Firmware Environment (CFE) support
- *
- * Copyright 2000, 2001, 2002
- * Broadcom Corporation. All rights reserved.
- *
- * Copyright (C) 2006 Michael Buesch
- *
- * Original Authors: Mitch Lichtenberg, Chris Demetriou
- *
- * This software is furnished under license and may be used and copied only
- * in accordance with the following terms and conditions. Subject to these
- * conditions, you may download, copy, install, use, modify and distribute
- * modified or unmodified copies of this software in source and/or binary
- * form. No title or ownership is transferred hereby.
- *
- * 1) Any source code used, modified or distributed must reproduce and
- * retain this copyright notice and list of conditions as they appear in
- * the source file.
- *
- * 2) No right is granted to use any trade name, trademark, or logo of
- * Broadcom Corporation. The "Broadcom Corporation" name may not be
- * used to endorse or promote products derived from this software
- * without the prior written permission of Broadcom Corporation.
- *
- * 3) THIS SOFTWARE IS PROVIDED "AS-IS" AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
- * NON-INFRINGEMENT ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM BE LIABLE
- * FOR ANY DAMAGES WHATSOEVER, AND IN PARTICULAR, BROADCOM SHALL NOT BE
- * LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
- * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
- * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
- * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
- * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
- * OR OTHERWISE), EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- */
-
-#ifndef LINUX_CFE_API_H_
-#define LINUX_CFE_API_H_
-
-#include <linux/types.h>
-
-
-#define CFE_MI_RESERVED 0 /* memory is reserved, do not use */
-#define CFE_MI_AVAILABLE 1 /* memory is available */
-
-#define CFE_FLG_WARMSTART 0x00000001
-#define CFE_FLG_FULL_ARENA 0x00000001
-#define CFE_FLG_ENV_PERMANENT 0x00000001
-
-#define CFE_CPU_CMD_START 1
-#define CFE_CPU_CMD_STOP 0
-
-#define CFE_STDHANDLE_CONSOLE 0
-
-#define CFE_DEV_NETWORK 1
-#define CFE_DEV_DISK 2
-#define CFE_DEV_FLASH 3
-#define CFE_DEV_SERIAL 4
-#define CFE_DEV_CPU 5
-#define CFE_DEV_NVRAM 6
-#define CFE_DEV_CLOCK 7
-#define CFE_DEV_OTHER 8
-#define CFE_DEV_MASK 0x0F
-
-#define CFE_CACHE_FLUSH_D 1
-#define CFE_CACHE_INVAL_I 2
-#define CFE_CACHE_INVAL_D 4
-#define CFE_CACHE_INVAL_L2 8
-
-#define CFE_FWI_64BIT 0x00000001
-#define CFE_FWI_32BIT 0x00000002
-#define CFE_FWI_RELOC 0x00000004
-#define CFE_FWI_UNCACHED 0x00000008
-#define CFE_FWI_MULTICPU 0x00000010
-#define CFE_FWI_FUNCSIM 0x00000020
-#define CFE_FWI_RTLSIM 0x00000040
-
-struct cfe_fwinfo {
- s64 version; /* major, minor, eco version */
- s64 totalmem; /* total installed mem */
- s64 flags; /* various flags */
- s64 boardid; /* board ID */
- s64 bootarea_va; /* VA of boot area */
- s64 bootarea_pa; /* PA of boot area */
- s64 bootarea_size; /* size of boot area */
-};
-
-
-/* The public CFE API */
-
-int cfe_present(void); /* Check if we booted from CFE. Returns bool */
-
-int cfe_getticks(s64 *ticks);
-int cfe_close(int handle);
-int cfe_cpu_start(int cpu, void (*fn)(void), long sp, long gp, long a1);
-int cfe_cpu_stop(int cpu);
-int cfe_enumenv(int idx, char *name, int namelen, char *val, int vallen);
-int cfe_enumdev(int idx, char *name, int namelen);
-int cfe_enummem(int idx, int flags, u64 *start, u64 *length,
- u64 *type);
-int cfe_exit(int warm, int status);
-int cfe_flushcache(int flags);
-int cfe_getdevinfo(char *name);
-int cfe_getenv(char *name, char *dest, int destlen);
-int cfe_getfwinfo(struct cfe_fwinfo *info);
-int cfe_getstdhandle(int handletype);
-int cfe_inpstat(int handle);
-int cfe_ioctl(int handle, unsigned int ioctlnum, unsigned char *buffer,
- int length, int *retlen, u64 offset);
-int cfe_open(char *name);
-int cfe_read(int handle, unsigned char *buffer, int length);
-int cfe_readblk(int handle, s64 offset, unsigned char *buffer, int length);
-int cfe_setenv(char *name, char *val);
-int cfe_write(int handle, unsigned char *buffer, int length);
-int cfe_writeblk(int handle, s64 offset, unsigned char *buffer,
- int length);
-
-
-/* High level API */
-
-/* Print some information to CFE's console (most likely serial line) */
-int cfe_printk(const char *fmt, ...) __attribute__((format(printf, 1, 2)));
-int cfe_vprintk(const char *fmt, va_list args);
-
-
-
-/* Error codes returned by the low API functions */
-
-#define CFE_ISERR(errcode) (errcode < 0)
-
-#define CFE_OK 0
-#define CFE_ERR -1 /* generic error */
-#define CFE_ERR_INV_COMMAND -2
-#define CFE_ERR_EOF -3
-#define CFE_ERR_IOERR -4
-#define CFE_ERR_NOMEM -5
-#define CFE_ERR_DEVNOTFOUND -6
-#define CFE_ERR_DEVOPEN -7
-#define CFE_ERR_INV_PARAM -8
-#define CFE_ERR_ENVNOTFOUND -9
-#define CFE_ERR_ENVREADONLY -10
-
-#define CFE_ERR_NOTELF -11
-#define CFE_ERR_NOT32BIT -12
-#define CFE_ERR_WRONGENDIAN -13
-#define CFE_ERR_BADELFVERS -14
-#define CFE_ERR_NOTMIPS -15
-#define CFE_ERR_BADELFFMT -16
-#define CFE_ERR_BADADDR -17
-
-#define CFE_ERR_FILENOTFOUND -18
-#define CFE_ERR_UNSUPPORTED -19
-
-#define CFE_ERR_HOSTUNKNOWN -20
-
-#define CFE_ERR_TIMEOUT -21
-
-#define CFE_ERR_PROTOCOLERR -22
-
-#define CFE_ERR_NETDOWN -23
-#define CFE_ERR_NONAMESERVER -24
-
-#define CFE_ERR_NOHANDLES -25
-#define CFE_ERR_ALREADYBOUND -26
-
-#define CFE_ERR_CANNOTSET -27
-#define CFE_ERR_NOMORE -28
-#define CFE_ERR_BADFILESYS -29
-#define CFE_ERR_FSNOTAVAIL -30
-
-#define CFE_ERR_INVBOOTBLOCK -31
-#define CFE_ERR_WRONGDEVTYPE -32
-#define CFE_ERR_BBCHECKSUM -33
-#define CFE_ERR_BOOTPROGCHKSUM -34
-
-#define CFE_ERR_LDRNOTAVAIL -35
-
-#define CFE_ERR_NOTREADY -36
-
-#define CFE_ERR_GETMEM -37
-#define CFE_ERR_SETMEM -38
-
-#define CFE_ERR_NOTCONN -39
-#define CFE_ERR_ADDRINUSE -40
-
-
-#endif /* LINUX_CFE_API_H_ */
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2003 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-
-#ifndef __6338_INTR_H
-#define __6338_INTR_H
-
-/*=====================================================================*/
-/* BCM6338 External Interrupt Level Assignments */
-/*=====================================================================*/
-#define INTERRUPT_ID_EXTERNAL_0 3
-#define INTERRUPT_ID_EXTERNAL_1 4
-#define INTERRUPT_ID_EXTERNAL_2 5
-#define INTERRUPT_ID_EXTERNAL_3 6
-
-/*=====================================================================*/
-/* BCM6338 Timer Interrupt Level Assignments */
-/*=====================================================================*/
-#define MIPS_TIMER_INT 7
-
-/*=====================================================================*/
-/* Peripheral ISR Table Offset */
-/*=====================================================================*/
-#define INTERNAL_ISR_TABLE_OFFSET 8
-
-/*=====================================================================*/
-/* Logical Peripheral Interrupt IDs */
-/*=====================================================================*/
-
-#define INTERRUPT_ID_TIMER (INTERNAL_ISR_TABLE_OFFSET + 0)
-#define INTERRUPT_ID_SPI (INTERNAL_ISR_TABLE_OFFSET + 1)
-#define INTERRUPT_ID_UART (INTERNAL_ISR_TABLE_OFFSET + 2)
-#define INTERRUPT_ID_DG (INTERNAL_ISR_TABLE_OFFSET + 4)
-#define INTERRUPT_ID_ADSL (INTERNAL_ISR_TABLE_OFFSET + 5)
-#define INTERRUPT_ID_ATM (INTERNAL_ISR_TABLE_OFFSET + 6)
-#define INTERRUPT_ID_USBS (INTERNAL_ISR_TABLE_OFFSET + 7)
-#define INTERRUPT_ID_EMAC1 (INTERNAL_ISR_TABLE_OFFSET + 8)
-#define INTERRUPT_ID_EPHY (INTERNAL_ISR_TABLE_OFFSET + 9)
-#define INTERRUPT_ID_SDRAM (INTERNAL_ISR_TABLE_OFFSET + 10)
-#define INTERRUPT_ID_USB_CNTL_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 11)
-#define INTERRUPT_ID_USB_CNTL_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 12)
-#define INTERRUPT_ID_USB_BULK_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 13)
-#define INTERRUPT_ID_USB_BULK_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 14)
-#define INTERRUPT_ID_EMAC1_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 15)
-#define INTERRUPT_ID_EMAC1_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 16)
-#define INTERRUPT_ID_SDIO (INTERNAL_ISR_TABLE_OFFSET + 17)
-
-#endif /* __BCM6338_H */
-
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2004 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-
-#ifndef __BCM6338_MAP_H
-#define __BCM6338_MAP_H
-
-#include "bcmtypes.h"
-
-#define PERF_BASE 0xfffe0000
-#define TIMR_BASE 0xfffe0200
-#define UART_BASE 0xfffe0300
-#define GPIO_BASE 0xfffe0400
-#define SPI_BASE 0xfffe0c00
-
-typedef struct PerfControl {
- uint32 RevID;
- uint16 testControl;
- uint16 blkEnables;
-#define EMAC_CLK_EN 0x0010
-#define USBS_CLK_EN 0x0010
-#define SAR_CLK_EN 0x0020
-
-#define SPI_CLK_EN 0x0200
-
- uint32 pll_control;
-#define SOFT_RESET 0x00000001
-
- uint32 IrqMask;
- uint32 IrqStatus;
-
- uint32 ExtIrqCfg;
-#define EI_SENSE_SHFT 0
-#define EI_STATUS_SHFT 5
-#define EI_CLEAR_SHFT 10
-#define EI_MASK_SHFT 15
-#define EI_INSENS_SHFT 20
-#define EI_LEVEL_SHFT 25
-
- uint32 unused[4]; /* (18) */
- uint32 BlockSoftReset; /* (28) */
-#define BSR_SPI 0x00000001
-#define BSR_EMAC 0x00000004
-#define BSR_USBH 0x00000008
-#define BSR_USBS 0x00000010
-#define BSR_ADSL 0x00000020
-#define BSR_DMAMEM 0x00000040
-#define BSR_SAR 0x00000080
-#define BSR_ACLC 0x00000100
-#define BSR_ADSL_MIPS_PLL 0x00000400
-#define BSR_ALL_BLOCKS \
- (BSR_SPI | BSR_EMAC | BSR_USBH | BSR_USBS | BSR_ADSL | BSR_DMAMEM | \
- BSR_SAR | BSR_ACLC | BSR_ADSL_MIPS_PLL)
-} PerfControl;
-
-#define PERF ((volatile PerfControl * const) PERF_BASE)
-
-
-typedef struct Timer {
- uint16 unused0;
- byte TimerMask;
-#define TIMER0EN 0x01
-#define TIMER1EN 0x02
-#define TIMER2EN 0x04
- byte TimerInts;
-#define TIMER0 0x01
-#define TIMER1 0x02
-#define TIMER2 0x04
-#define WATCHDOG 0x08
- uint32 TimerCtl0;
- uint32 TimerCtl1;
- uint32 TimerCtl2;
-#define TIMERENABLE 0x80000000
-#define RSTCNTCLR 0x40000000
- uint32 TimerCnt0;
- uint32 TimerCnt1;
- uint32 TimerCnt2;
- uint32 WatchDogDefCount;
-
- /* Write 0xff00 0x00ff to Start timer
- * Write 0xee00 0x00ee to Stop and re-load default count
- * Read from this register returns current watch dog count
- */
- uint32 WatchDogCtl;
-
- /* Number of 40-MHz ticks for WD Reset pulse to last */
- uint32 WDResetCount;
-} Timer;
-
-#define TIMER ((volatile Timer * const) TIMR_BASE)
-typedef struct UartChannel {
- byte unused0;
- byte control;
-#define BRGEN 0x80 /* Control register bit defs */
-#define TXEN 0x40
-#define RXEN 0x20
-#define LOOPBK 0x10
-#define TXPARITYEN 0x08
-#define TXPARITYEVEN 0x04
-#define RXPARITYEN 0x02
-#define RXPARITYEVEN 0x01
-
- byte config;
-#define XMITBREAK 0x40
-#define BITS5SYM 0x00
-#define BITS6SYM 0x10
-#define BITS7SYM 0x20
-#define BITS8SYM 0x30
-#define ONESTOP 0x07
-#define TWOSTOP 0x0f
- /* 4-LSBS represent STOP bits/char
- * in 1/8 bit-time intervals. Zero
- * represents 1/8 stop bit interval.
- * Fifteen represents 2 stop bits.
- */
- byte fifoctl;
-#define RSTTXFIFOS 0x80
-#define RSTRXFIFOS 0x40
- /* 5-bit TimeoutCnt is in low bits of this register.
- * This count represents the number of characters
- * idle times before setting receive Irq when below threshold
- */
- uint32 baudword;
- /* When divide SysClk/2/(1+baudword) we should get 32*bit-rate
- */
-
- byte txf_levl; /* Read-only fifo depth */
- byte rxf_levl; /* Read-only fifo depth */
- byte fifocfg; /* Upper 4-bits are TxThresh, Lower are
- * RxThreshold. Irq can be asserted
- * when rx fifo> thresh, txfifo<thresh
- */
- byte prog_out; /* Set value of DTR (Bit0), RTS (Bit1)
- * if these bits are also enabled to GPIO_o
- */
-#define DTREN 0x01
-#define RTSEN 0x02
-
- byte unused1;
- byte DeltaIPEdgeNoSense; /* Low 4-bits, set corr bit to 1 to
- * detect irq on rising AND falling
- * edges for corresponding GPIO_i
- * if enabled (edge insensitive)
- */
- byte DeltaIPConfig_Mask; /* Upper 4 bits: 1 for posedge sense
- * 0 for negedge sense if
- * not configured for edge
- * insensitive (see above)
- * Lower 4 bits: Mask to enable change
- * detection IRQ for corresponding
- * GPIO_i
- */
- byte DeltaIP_SyncIP; /* Upper 4 bits show which bits
- * have changed (may set IRQ).
- * read automatically clears bit
- * Lower 4 bits are actual status
- */
-
- uint16 intMask; /* Same Bit defs for Mask and status */
- uint16 intStatus;
-#define DELTAIP 0x0001
-#define TXUNDERR 0x0002
-#define TXOVFERR 0x0004
-#define TXFIFOTHOLD 0x0008
-#define TXREADLATCH 0x0010
-#define TXFIFOEMT 0x0020
-#define RXUNDERR 0x0040
-#define RXOVFERR 0x0080
-#define RXTIMEOUT 0x0100
-#define RXFIFOFULL 0x0200
-#define RXFIFOTHOLD 0x0400
-#define RXFIFONE 0x0800
-#define RXFRAMERR 0x1000
-#define RXPARERR 0x2000
-#define RXBRK 0x4000
-
- uint16 unused2;
- uint16 Data; /* Write to TX, Read from RX */
- /* bits 11:8 are BRK,PAR,FRM errors */
-
- uint32 unused3;
- uint32 unused4;
-} Uart;
-
-#define UART ((volatile Uart * const) UART_BASE)
-
-typedef struct GpioControl {
- uint32 unused0;
- uint32 GPIODir; /* bits 7:0 */
- uint32 unused1;
- uint32 GPIOio; /* bits 7:0 */
- uint32 LEDCtrl;
-#define LED3_STROBE 0x08000000
-#define LED2_STROBE 0x04000000
-#define LED1_STROBE 0x02000000
-#define LED0_STROBE 0x01000000
-#define LED_TEST 0x00010000
-#define LED3_DISABLE_LINK_ACT 0x00008000
-#define LED2_DISABLE_LINK_ACT 0x00004000
-#define LED1_DISABLE_LINK_ACT 0x00002000
-#define LED0_DISABLE_LINK_ACT 0x00001000
-#define LED_INTERVAL_SET_MASK 0x00000f00
-#define LED_INTERVAL_SET_320MS 0x00000500
-#define LED_INTERVAL_SET_160MS 0x00000400
-#define LED_INTERVAL_SET_80MS 0x00000300
-#define LED_INTERVAL_SET_40MS 0x00000200
-#define LED_INTERVAL_SET_20MS 0x00000100
-#define LED3_ON 0x00000080
-#define LED2_ON 0x00000040
-#define LED1_ON 0x00000020
-#define LED0_ON 0x00000010
-#define LED3_ENABLE 0x00000008
-#define LED2_ENABLE 0x00000004
-#define LED1_ENABLE 0x00000002
-#define LED0_ENABLE 0x00000001
- uint32 SpiSlaveCfg;
-#define SPI_SLAVE_RESET 0x00010000
-#define SPI_RESTRICT 0x00000400
-#define SPI_DELAY_DISABLE 0x00000200
-#define SPI_PROBE_MUX_SEL_MASK 0x000001e0
-#define SPI_SER_ADDR_CFG_MASK 0x0000000c
-#define SPI_MODE 0x00000001
- uint32 vRegConfig;
-} GpioControl;
-
-#define GPIO ((volatile GpioControl * const) GPIO_BASE)
-
-/* Number to mask conversion macro used for GPIODir and GPIOio */
-#define GPIO_NUM_MAX_BITS_MASK 0x0f
-#define GPIO_NUM_TO_MASK(X) (1 << ((X) & GPIO_NUM_MAX_BITS_MASK))
-
-/*
-** Spi Controller
-*/
-
-typedef struct SpiControl {
- uint16 spiCmd; /* (0x0): SPI command */
-#define SPI_CMD_START_IMMEDIATE 3
-
-#define SPI_CMD_COMMAND_SHIFT 0
-#define SPI_CMD_DEVICE_ID_SHIFT 4
-#define SPI_CMD_PREPEND_BYTE_CNT_SHIFT 8
-
- byte spiIntStatus; /* (0x2): SPI interrupt status */
- byte spiMaskIntStatus; /* (0x3): SPI masked interrupt status */
-
- byte spiIntMask; /* (0x4): SPI interrupt mask */
-#define SPI_INTR_CMD_DONE 0x01
-#define SPI_INTR_CLEAR_ALL 0x1f
-
- byte spiStatus; /* (0x5): SPI status */
-
- byte spiClkCfg; /* (0x6): SPI clock configuration */
-
- byte spiFillByte; /* (0x7): SPI fill byte */
-
- byte unused0;
- byte spiMsgTail; /* (0x9): msgtail */
- byte unused1;
- byte spiRxTail; /* (0xB): rxtail */
-
- uint32 unused2[13]; /* (0x0c - 0x3c) reserved */
-
- byte spiMsgCtl; /* (0x40) control byte */
-#define HALF_DUPLEX_W 1
-#define HALF_DUPLEX_R 2
-#define SPI_MSG_TYPE_SHIFT 6
-#define SPI_BYTE_CNT_SHIFT 0
- byte spiMsgData[63]; /* (0x41 - 0x7f) msg data */
- byte spiRxDataFifo[64]; /* (0x80 - 0xbf) rx data */
- byte unused3[64]; /* (0xc0 - 0xff) reserved */
-} SpiControl;
-
-#define SPI ((volatile SpiControl * const) SPI_BASE)
-
-/*
-** External Bus Interface
-*/
-typedef struct EbiChipSelect {
- uint32 base; /* base address in upper 24 bits */
-#define EBI_SIZE_8K 0
-#define EBI_SIZE_16K 1
-#define EBI_SIZE_32K 2
-#define EBI_SIZE_64K 3
-#define EBI_SIZE_128K 4
-#define EBI_SIZE_256K 5
-#define EBI_SIZE_512K 6
-#define EBI_SIZE_1M 7
-#define EBI_SIZE_2M 8
-#define EBI_SIZE_4M 9
-#define EBI_SIZE_8M 10
-#define EBI_SIZE_16M 11
-#define EBI_SIZE_32M 12
-#define EBI_SIZE_64M 13
-#define EBI_SIZE_128M 14
-#define EBI_SIZE_256M 15
- uint32 config;
-#define EBI_ENABLE 0x00000001 /* .. enable this range */
-#define EBI_WAIT_STATES 0x0000000e /* .. mask for wait states */
-#define EBI_WTST_SHIFT 1 /* .. for shifting wait states */
-#define EBI_WORD_WIDE 0x00000010 /* .. 16-bit peripheral, else 8 */
-#define EBI_WREN 0x00000020 /* enable posted writes */
-#define EBI_POLARITY 0x00000040 /* .. set to invert something,
- ** don't know what yet */
-#define EBI_TS_TA_MODE 0x00000080 /* .. use TS/TA mode */
-#define EBI_TS_SEL 0x00000100 /* .. drive tsize, not bs_b */
-#define EBI_FIFO 0x00000200 /* .. use fifo */
-#define EBI_RE 0x00000400 /* .. Reverse Endian */
-} EbiChipSelect;
-
-typedef struct MpiRegisters {
- EbiChipSelect cs[1]; /* size chip select configuration */
-} MpiRegisters;
-
-#define MPI ((volatile MpiRegisters * const) MPI_BASE)
-
-
-#endif
-
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2002 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-
-#ifndef __6345_INTR_H
-#define __6345_INTR_H
-
-
-/*=====================================================================*/
-/* BCM6345 External Interrupt Level Assignments */
-/*=====================================================================*/
-#define INTERRUPT_ID_EXTERNAL_0 3
-#define INTERRUPT_ID_EXTERNAL_1 4
-#define INTERRUPT_ID_EXTERNAL_2 5
-#define INTERRUPT_ID_EXTERNAL_3 6
-
-/*=====================================================================*/
-/* BCM6345 Timer Interrupt Level Assignments */
-/*=====================================================================*/
-#define MIPS_TIMER_INT 7
-
-/*=====================================================================*/
-/* Peripheral ISR Table Offset */
-/*=====================================================================*/
-#define INTERNAL_ISR_TABLE_OFFSET 8
-#define DMA_ISR_TABLE_OFFSET (INTERNAL_ISR_TABLE_OFFSET + 13)
-
-/*=====================================================================*/
-/* Logical Peripheral Interrupt IDs */
-/*=====================================================================*/
-
-/* Internal peripheral interrupt IDs */
-#define INTERRUPT_ID_TIMER (INTERNAL_ISR_TABLE_OFFSET + 0)
-#define INTERRUPT_ID_UART (INTERNAL_ISR_TABLE_OFFSET + 2)
-#define INTERRUPT_ID_ADSL (INTERNAL_ISR_TABLE_OFFSET + 3)
-#define INTERRUPT_ID_ATM (INTERNAL_ISR_TABLE_OFFSET + 4)
-#define INTERRUPT_ID_USB (INTERNAL_ISR_TABLE_OFFSET + 5)
-#define INTERRUPT_ID_EMAC (INTERNAL_ISR_TABLE_OFFSET + 8)
-#define INTERRUPT_ID_EPHY (INTERNAL_ISR_TABLE_OFFSET + 12)
-
-/* DMA channel interrupt IDs */
-#define INTERRUPT_ID_EMAC_RX_CHAN (DMA_ISR_TABLE_OFFSET + EMAC_RX_CHAN)
-#define INTERRUPT_ID_EMAC_TX_CHAN (DMA_ISR_TABLE_OFFSET + EMAC_TX_CHAN)
-#define INTERRUPT_ID_EBI_RX_CHAN (DMA_ISR_TABLE_OFFSET + EBI_RX_CHAN)
-#define INTERRUPT_ID_EBI_TX_CHAN (DMA_ISR_TABLE_OFFSET + EBI_TX_CHAN)
-#define INTERRUPT_ID_RESERVED_RX_CHAN (DMA_ISR_TABLE_OFFSET + RESERVED_RX_CHAN)
-#define INTERRUPT_ID_RESERVED_TX_CHAN (DMA_ISR_TABLE_OFFSET + RESERVED_TX_CHAN)
-#define INTERRUPT_ID_USB_BULK_RX_CHAN (DMA_ISR_TABLE_OFFSET + USB_BULK_RX_CHAN)
-#define INTERRUPT_ID_USB_BULK_TX_CHAN (DMA_ISR_TABLE_OFFSET + USB_BULK_TX_CHAN)
-#define INTERRUPT_ID_USB_CNTL_RX_CHAN (DMA_ISR_TABLE_OFFSET + USB_CNTL_RX_CHAN)
-#define INTERRUPT_ID_USB_CNTL_TX_CHAN (DMA_ISR_TABLE_OFFSET + USB_CNTL_TX_CHAN)
-#define INTERRUPT_ID_USB_ISO_RX_CHAN (DMA_ISR_TABLE_OFFSET + USB_ISO_RX_CHAN)
-#define INTERRUPT_ID_USB_ISO_TX_CHAN (DMA_ISR_TABLE_OFFSET + USB_ISO_TX_CHAN)
-
-
-#endif /* __BCM6345_H */
-
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2002 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-
-#ifndef __BCM6345_MAP_H
-#define __BCM6345_MAP_H
-
-
-#include "bcmtypes.h"
-#include "6345_intr.h"
-
-typedef struct IntControl {
- uint32 RevID;
- uint16 testControl;
- uint16 blkEnables;
-#define USB_CLK_EN 0x0100
-#define EMAC_CLK_EN 0x0080
-#define UART_CLK_EN 0x0008
-#define CPU_CLK_EN 0x0001
-
- uint32 pll_control;
-#define SOFT_RESET 0x00000001
-
- uint32 IrqMask;
- uint32 IrqStatus;
-
- uint32 ExtIrqCfg;
-#define EI_SENSE_SHFT 0
-#define EI_STATUS_SHFT 4
-#define EI_CLEAR_SHFT 8
-#define EI_MASK_SHFT 12
-#define EI_INSENS_SHFT 16
-#define EI_LEVEL_SHFT 20
-} IntControl;
-
-#define INTC_BASE 0xfffe0000
-#define PERF ((volatile IntControl * const) INTC_BASE)
-
-#define TIMR_BASE 0xfffe0200
-typedef struct Timer {
- uint16 unused0;
- byte TimerMask;
-#define TIMER0EN 0x01
-#define TIMER1EN 0x02
-#define TIMER2EN 0x04
- byte TimerInts;
-#define TIMER0 0x01
-#define TIMER1 0x02
-#define TIMER2 0x04
-#define WATCHDOG 0x08
- uint32 TimerCtl0;
- uint32 TimerCtl1;
- uint32 TimerCtl2;
-#define TIMERENABLE 0x80000000
-#define RSTCNTCLR 0x40000000
- uint32 TimerCnt0;
- uint32 TimerCnt1;
- uint32 TimerCnt2;
- uint32 WatchDogDefCount;
-
- /* Write 0xff00 0x00ff to Start timer
- * Write 0xee00 0x00ee to Stop and re-load default count
- * Read from this register returns current watch dog count
- */
- uint32 WatchDogCtl;
-
- /* Number of 40-MHz ticks for WD Reset pulse to last */
- uint32 WDResetCount;
-} Timer;
-
-#define TIMER ((volatile Timer * const) TIMR_BASE)
-
-typedef struct UartChannel {
- byte unused0;
- byte control;
-#define BRGEN 0x80 /* Control register bit defs */
-#define TXEN 0x40
-#define RXEN 0x20
-#define TXPARITYEN 0x08
-#define TXPARITYEVEN 0x04
-#define RXPARITYEN 0x02
-#define RXPARITYEVEN 0x01
- byte config;
-#define BITS5SYM 0x00
-#define BITS6SYM 0x10
-#define BITS7SYM 0x20
-#define BITS8SYM 0x30
-#define XMITBREAK 0x40
-#define ONESTOP 0x07
-#define TWOSTOP 0x0f
-
- byte fifoctl;
-#define RSTTXFIFOS 0x80
-#define RSTRXFIFOS 0x40
- uint32 baudword;
-
- byte txf_levl;
- byte rxf_levl;
- byte fifocfg;
- byte prog_out;
-
- byte unused1;
- byte DeltaIPEdgeNoSense;
- byte DeltaIPConfig_Mask;
- byte DeltaIP_SyncIP;
- uint16 intMask;
- uint16 intStatus;
-#define TXUNDERR 0x0002
-#define TXOVFERR 0x0004
-#define TXFIFOEMT 0x0020
-#define RXOVFERR 0x0080
-#define RXFIFONE 0x0800
-#define RXFRAMERR 0x1000
-#define RXPARERR 0x2000
-#define RXBRK 0x4000
-
- uint16 unused2;
- uint16 Data;
- uint32 unused3;
- uint32 unused4;
-} Uart;
-
-#define UART_BASE 0xfffe0300
-#define UART ((volatile Uart * const) UART_BASE)
-
-typedef struct GpioControl {
- uint16 unused0;
- byte unused1;
- byte TBusSel;
-
- uint16 unused2;
- uint16 GPIODir;
- byte unused3;
- byte Leds;
- uint16 GPIOio;
-
- uint32 UartCtl;
-} GpioControl;
-
-#define GPIO_BASE 0xfffe0400
-#define GPIO ((volatile GpioControl * const) GPIO_BASE)
-
-#define GPIO_NUM_MAX_BITS_MASK 0x0f
-#define GPIO_NUM_TO_MASK(X) (1 << ((X) & GPIO_NUM_MAX_BITS_MASK))
-
-
-#endif
-
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2003 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-
-#ifndef __6348_INTR_H
-#define __6348_INTR_H
-
-
-/*=====================================================================*/
-/* BCM6348 External Interrupt Level Assignments */
-/*=====================================================================*/
-#define INTERRUPT_ID_EXTERNAL_0 3
-#define INTERRUPT_ID_EXTERNAL_1 4
-#define INTERRUPT_ID_EXTERNAL_2 5
-#define INTERRUPT_ID_EXTERNAL_3 6
-
-/*=====================================================================*/
-/* BCM6348 Timer Interrupt Level Assignments */
-/*=====================================================================*/
-#define MIPS_TIMER_INT 7
-
-/*=====================================================================*/
-/* Peripheral ISR Table Offset */
-/*=====================================================================*/
-#define INTERNAL_ISR_TABLE_OFFSET 8
-
-/*=====================================================================*/
-/* Logical Peripheral Interrupt IDs */
-/*=====================================================================*/
-
-#define INTERRUPT_ID_TIMER (INTERNAL_ISR_TABLE_OFFSET + 0)
-#define INTERRUPT_ID_SPI (INTERNAL_ISR_TABLE_OFFSET + 1)
-#define INTERRUPT_ID_UART (INTERNAL_ISR_TABLE_OFFSET + 2)
-#define INTERRUPT_ID_ADSL (INTERNAL_ISR_TABLE_OFFSET + 4)
-#define INTERRUPT_ID_ATM (INTERNAL_ISR_TABLE_OFFSET + 5)
-#define INTERRUPT_ID_USBS (INTERNAL_ISR_TABLE_OFFSET + 6)
-#define INTERRUPT_ID_EMAC2 (INTERNAL_ISR_TABLE_OFFSET + 7)
-#define INTERRUPT_ID_EMAC1 (INTERNAL_ISR_TABLE_OFFSET + 8)
-#define INTERRUPT_ID_EPHY (INTERNAL_ISR_TABLE_OFFSET + 9)
-#define INTERRUPT_ID_M2M (INTERNAL_ISR_TABLE_OFFSET + 10)
-#define INTERRUPT_ID_ACLC (INTERNAL_ISR_TABLE_OFFSET + 11)
-#define INTERRUPT_ID_USBH (INTERNAL_ISR_TABLE_OFFSET + 12)
-#define INTERRUPT_ID_SDRAM (INTERNAL_ISR_TABLE_OFFSET + 13)
-#define INTERRUPT_ID_USB_CNTL_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 14)
-#define INTERRUPT_ID_USB_CNTL_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 15)
-#define INTERRUPT_ID_USB_BULK_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 16)
-#define INTERRUPT_ID_USB_BULK_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 17)
-#define INTERRUPT_ID_USB_ISO_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 18)
-#define INTERRUPT_ID_USB_ISO_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 19)
-#define INTERRUPT_ID_EMAC1_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 20)
-#define INTERRUPT_ID_EMAC1_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 21)
-#define INTERRUPT_ID_EMAC2_RX_DMA (INTERNAL_ISR_TABLE_OFFSET + 22)
-#define INTERRUPT_ID_EMAC2_TX_DMA (INTERNAL_ISR_TABLE_OFFSET + 23)
-#define INTERRUPT_ID_MPI (INTERNAL_ISR_TABLE_OFFSET + 24)
-#define INTERRUPT_ID_DG (INTERNAL_ISR_TABLE_OFFSET + 25)
-
-
-#endif /* __BCM6348_H */
-
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2002 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-
-#ifndef __BCM6348_MAP_H
-#define __BCM6348_MAP_H
-
-#include "bcmtypes.h"
-
-#define PERF_BASE 0xfffe0000
-#define TIMR_BASE 0xfffe0200
-#define UART_BASE 0xfffe0300
-#define GPIO_BASE 0xfffe0400
-#define MPI_BASE 0xfffe2000 /* MPI control registers */
-#define USB_HOST_BASE 0xfffe1b00 /* USB host registers */
-#define USB_HOST_NON_OHCI 0xfffe1c00 /* USB host non-OHCI registers */
-
-typedef struct PerfControl {
- uint32 RevID;
- uint16 testControl;
- uint16 blkEnables;
-#define EMAC_CLK_EN 0x0010
-#define SAR_CLK_EN 0x0020
-#define USBS_CLK_EN 0x0040
-#define USBH_CLK_EN 0x0100
-
- uint32 pll_control;
-#define SOFT_RESET 0x00000001
-
- uint32 IrqMask;
- uint32 IrqStatus;
-
- uint32 ExtIrqCfg;
-#define EI_SENSE_SHFT 0
-#define EI_STATUS_SHFT 5
-#define EI_CLEAR_SHFT 10
-#define EI_MASK_SHFT 15
-#define EI_INSENS_SHFT 20
-#define EI_LEVEL_SHFT 25
-
- uint32 unused[4]; /* (18) */
- uint32 BlockSoftReset; /* (28) */
-#define BSR_SPI 0x00000001
-#define BSR_EMAC 0x00000004
-#define BSR_USBH 0x00000008
-#define BSR_USBS 0x00000010
-#define BSR_ADSL 0x00000020
-#define BSR_DMAMEM 0x00000040
-#define BSR_SAR 0x00000080
-#define BSR_ACLC 0x00000100
-#define BSR_ADSL_MIPS_PLL 0x00000400
-#define BSR_ALL_BLOCKS \
- (BSR_SPI | BSR_EMAC | BSR_USBH | BSR_USBS | BSR_ADSL | BSR_DMAMEM | \
- BSR_SAR | BSR_ACLC | BSR_ADSL_MIPS_PLL)
- uint32 unused2[2]; /* (2c) */
- uint32 PllStrap; /* (34) */
-#define PLL_N1_SHFT 20
-#define PLL_N1_MASK (7<<PLL_N1_SHFT)
-#define PLL_N2_SHFT 15
-#define PLL_N2_MASK (0x1f<<PLL_N2_SHFT)
-#define PLL_M1_REF_SHFT 12
-#define PLL_M1_REF_MASK (7<<PLL_M1_REF_SHFT)
-#define PLL_M2_REF_SHFT 9
-#define PLL_M2_REF_MASK (7<<PLL_M2_REF_SHFT)
-#define PLL_M1_CPU_SHFT 6
-#define PLL_M1_CPU_MASK (7<<PLL_M1_CPU_SHFT)
-#define PLL_M1_BUS_SHFT 3
-#define PLL_M1_BUS_MASK (7<<PLL_M1_BUS_SHFT)
-#define PLL_M2_BUS_SHFT 0
-#define PLL_M2_BUS_MASK (7<<PLL_M2_BUS_SHFT)
-} PerfControl;
-
-#define PERF ((volatile PerfControl * const) PERF_BASE)
-
-typedef struct Timer {
- uint16 unused0;
- byte TimerMask;
-#define TIMER0EN 0x01
-#define TIMER1EN 0x02
-#define TIMER2EN 0x04
- byte TimerInts;
-#define TIMER0 0x01
-#define TIMER1 0x02
-#define TIMER2 0x04
-#define WATCHDOG 0x08
- uint32 TimerCtl0;
- uint32 TimerCtl1;
- uint32 TimerCtl2;
-#define TIMERENABLE 0x80000000
-#define RSTCNTCLR 0x40000000
- uint32 TimerCnt0;
- uint32 TimerCnt1;
- uint32 TimerCnt2;
- uint32 WatchDogDefCount;
-
- /* Write 0xff00 0x00ff to Start timer
- * Write 0xee00 0x00ee to Stop and re-load default count
- * Read from this register returns current watch dog count
- */
- uint32 WatchDogCtl;
-
- /* Number of 40-MHz ticks for WD Reset pulse to last */
- uint32 WDResetCount;
-} Timer;
-
-#define TIMER ((volatile Timer * const) TIMR_BASE)
-
-typedef struct UartChannel {
- byte unused0;
- byte control;
-#define BRGEN 0x80 /* Control register bit defs */
-#define TXEN 0x40
-#define RXEN 0x20
-#define LOOPBK 0x10
-#define TXPARITYEN 0x08
-#define TXPARITYEVEN 0x04
-#define RXPARITYEN 0x02
-#define RXPARITYEVEN 0x01
-
- byte config;
-#define XMITBREAK 0x40
-#define BITS5SYM 0x00
-#define BITS6SYM 0x10
-#define BITS7SYM 0x20
-#define BITS8SYM 0x30
-#define ONESTOP 0x07
-#define TWOSTOP 0x0f
- /* 4-LSBS represent STOP bits/char
- * in 1/8 bit-time intervals. Zero
- * represents 1/8 stop bit interval.
- * Fifteen represents 2 stop bits.
- */
- byte fifoctl;
-#define RSTTXFIFOS 0x80
-#define RSTRXFIFOS 0x40
- /* 5-bit TimeoutCnt is in low bits of this register.
- * This count represents the number of characters
- * idle times before setting receive Irq when below threshold
- */
- uint32 baudword;
- /* When divide SysClk/2/(1+baudword) we should get 32*bit-rate
- */
-
- byte txf_levl; /* Read-only fifo depth */
- byte rxf_levl; /* Read-only fifo depth */
- byte fifocfg; /* Upper 4-bits are TxThresh, Lower are
- * RxThreshold. Irq can be asserted
- * when rx fifo> thresh, txfifo<thresh
- */
- byte prog_out; /* Set value of DTR (Bit0), RTS (Bit1)
- * if these bits are also enabled to GPIO_o
- */
-#define DTREN 0x01
-#define RTSEN 0x02
-
- byte unused1;
- byte DeltaIPEdgeNoSense; /* Low 4-bits, set corr bit to 1 to
- * detect irq on rising AND falling
- * edges for corresponding GPIO_i
- * if enabled (edge insensitive)
- */
- byte DeltaIPConfig_Mask; /* Upper 4 bits: 1 for posedge sense
- * 0 for negedge sense if
- * not configured for edge
- * insensitive (see above)
- * Lower 4 bits: Mask to enable change
- * detection IRQ for corresponding
- * GPIO_i
- */
- byte DeltaIP_SyncIP; /* Upper 4 bits show which bits
- * have changed (may set IRQ).
- * read automatically clears bit
- * Lower 4 bits are actual status
- */
-
- uint16 intMask; /* Same Bit defs for Mask and status */
- uint16 intStatus;
-#define DELTAIP 0x0001
-#define TXUNDERR 0x0002
-#define TXOVFERR 0x0004
-#define TXFIFOTHOLD 0x0008
-#define TXREADLATCH 0x0010
-#define TXFIFOEMT 0x0020
-#define RXUNDERR 0x0040
-#define RXOVFERR 0x0080
-#define RXTIMEOUT 0x0100
-#define RXFIFOFULL 0x0200
-#define RXFIFOTHOLD 0x0400
-#define RXFIFONE 0x0800
-#define RXFRAMERR 0x1000
-#define RXPARERR 0x2000
-#define RXBRK 0x4000
-
- uint16 unused2;
- uint16 Data; /* Write to TX, Read from RX */
- /* bits 11:8 are BRK,PAR,FRM errors */
-
- uint32 unused3;
- uint32 unused4;
-} Uart;
-
-#define UART ((volatile Uart * const) UART_BASE)
-
-typedef struct GpioControl {
- uint32 GPIODir_high; /* bits 36:32 */
- uint32 GPIODir; /* bits 31:00 */
- uint32 GPIOio_high; /* bits 36:32 */
- uint32 GPIOio; /* bits 31:00 */
- uint32 LEDCtrl;
-#define LED3_STROBE 0x08000000
-#define LED2_STROBE 0x04000000
-#define LED1_STROBE 0x02000000
-#define LED0_STROBE 0x01000000
-#define LED_TEST 0x00010000
-#define LED3_DISABLE_LINK_ACT 0x00008000
-#define LED2_DISABLE_LINK_ACT 0x00004000
-#define LED1_DISABLE_LINK_ACT 0x00002000
-#define LED0_DISABLE_LINK_ACT 0x00001000
-#define LED_INTERVAL_SET_MASK 0x00000f00
-#define LED_INTERVAL_SET_320MS 0x00000500
-#define LED_INTERVAL_SET_160MS 0x00000400
-#define LED_INTERVAL_SET_80MS 0x00000300
-#define LED_INTERVAL_SET_40MS 0x00000200
-#define LED_INTERVAL_SET_20MS 0x00000100
-#define LED3_ON 0x00000080
-#define LED2_ON 0x00000040
-#define LED1_ON 0x00000020
-#define LED0_ON 0x00000010
-#define LED3_ENABLE 0x00000008
-#define LED2_ENABLE 0x00000004
-#define LED1_ENABLE 0x00000002
-#define LED0_ENABLE 0x00000001
- uint32 SpiSlaveCfg;
-#define SPI_SLAVE_RESET 0x00010000
-#define SPI_RESTRICT 0x00000400
-#define SPI_DELAY_DISABLE 0x00000200
-#define SPI_PROBE_MUX_SEL_MASK 0x000001e0
-#define SPI_SER_ADDR_CFG_MASK 0x0000000c
-#define SPI_MODE 0x00000001
- uint32 GPIOMode;
-#define GROUP4_DIAG 0x00090000
-#define GROUP4_UTOPIA 0x00080000
-#define GROUP4_LEGACY_LED 0x00030000
-#define GROUP4_MII_SNOOP 0x00020000
-#define GROUP4_EXT_EPHY 0x00010000
-#define GROUP3_DIAG 0x00009000
-#define GROUP3_UTOPIA 0x00008000
-#define GROUP3_EXT_MII 0x00007000
-#define GROUP2_DIAG 0x00000900
-#define GROUP2_PCI 0x00000500
-#define GROUP1_DIAG 0x00000090
-#define GROUP1_UTOPIA 0x00000080
-#define GROUP1_SPI_UART 0x00000060
-#define GROUP1_SPI_MASTER 0x00000060
-#define GROUP1_MII_PCCARD 0x00000040
-#define GROUP1_MII_SNOOP 0x00000020
-#define GROUP1_EXT_EPHY 0x00000010
-#define GROUP0_DIAG 0x00000009
-#define GROUP0_EXT_MII 0x00000007
-
-} GpioControl;
-
-#define GPIO ((volatile GpioControl * const) GPIO_BASE)
-
-/* Number to mask conversion macro used for GPIODir and GPIOio */
-#define GPIO_NUM_TOTAL_BITS_MASK 0x3f
-#define GPIO_NUM_MAX_BITS_MASK 0x1f
-#define GPIO_NUM_TO_MASK(X) ( (((X) & GPIO_NUM_TOTAL_BITS_MASK) < 32) ? (1 << ((X) & GPIO_NUM_MAX_BITS_MASK)) : (0) )
-
-/* Number to mask conversion macro used for GPIODir_high and GPIOio_high */
-#define GPIO_NUM_MAX_BITS_MASK_HIGH 0x07
-#define GPIO_NUM_TO_MASK_HIGH(X) ( (((X) & GPIO_NUM_TOTAL_BITS_MASK) >= 32) ? (1 << ((X-32) & GPIO_NUM_MAX_BITS_MASK_HIGH)) : (0) )
-
-
-/*
-** External Bus Interface
-*/
-typedef struct EbiChipSelect {
- uint32 base; /* base address in upper 24 bits */
-#define EBI_SIZE_8K 0
-#define EBI_SIZE_16K 1
-#define EBI_SIZE_32K 2
-#define EBI_SIZE_64K 3
-#define EBI_SIZE_128K 4
-#define EBI_SIZE_256K 5
-#define EBI_SIZE_512K 6
-#define EBI_SIZE_1M 7
-#define EBI_SIZE_2M 8
-#define EBI_SIZE_4M 9
-#define EBI_SIZE_8M 10
-#define EBI_SIZE_16M 11
-#define EBI_SIZE_32M 12
-#define EBI_SIZE_64M 13
-#define EBI_SIZE_128M 14
-#define EBI_SIZE_256M 15
- uint32 config;
-#define EBI_ENABLE 0x00000001 /* .. enable this range */
-#define EBI_WAIT_STATES 0x0000000e /* .. mask for wait states */
-#define EBI_WTST_SHIFT 1 /* .. for shifting wait states */
-#define EBI_WORD_WIDE 0x00000010 /* .. 16-bit peripheral, else 8 */
-#define EBI_WREN 0x00000020 /* enable posted writes */
-#define EBI_POLARITY 0x00000040 /* .. set to invert something,
- ** don't know what yet */
-#define EBI_TS_TA_MODE 0x00000080 /* .. use TS/TA mode */
-#define EBI_TS_SEL 0x00000100 /* .. drive tsize, not bs_b */
-#define EBI_FIFO 0x00000200 /* .. use fifo */
-#define EBI_RE 0x00000400 /* .. Reverse Endian */
-} EbiChipSelect;
-
-typedef struct MpiRegisters {
- EbiChipSelect cs[7]; /* size chip select configuration */
-#define EBI_CS0_BASE 0
-#define EBI_CS1_BASE 1
-#define EBI_CS2_BASE 2
-#define EBI_CS3_BASE 3
-#define PCMCIA_COMMON_BASE 4
-#define PCMCIA_ATTRIBUTE_BASE 5
-#define PCMCIA_IO_BASE 6
- uint32 unused0[2]; /* reserved */
- uint32 ebi_control; /* ebi control */
- uint32 unused1[4]; /* reserved */
-#define EBI_ACCESS_TIMEOUT 0x000007FF
- uint32 pcmcia_cntl1; /* pcmcia control 1 */
-#define PCCARD_CARD_RESET 0x00040000
-#define CARDBUS_ENABLE 0x00008000
-#define PCMCIA_ENABLE 0x00004000
-#define PCMCIA_GPIO_ENABLE 0x00002000
-#define CARDBUS_IDSEL 0x00001F00
-#define VS2_OEN 0x00000080
-#define VS1_OEN 0x00000040
-#define VS2_OUT 0x00000020
-#define VS1_OUT 0x00000010
-#define VS2_IN 0x00000008
-#define VS1_IN 0x00000004
-#define CD2_IN 0x00000002
-#define CD1_IN 0x00000001
-#define VS_MASK 0x0000000C
-#define CD_MASK 0x00000003
- uint32 unused2; /* reserved */
- uint32 pcmcia_cntl2; /* pcmcia control 2 */
-#define PCMCIA_BYTESWAP_DIS 0x00000002
-#define PCMCIA_HALFWORD_EN 0x00000001
-#define RW_ACTIVE_CNT_BIT 2
-#define INACTIVE_CNT_BIT 8
-#define CE_SETUP_CNT_BIT 16
-#define CE_HOLD_CNT_BIT 24
- uint32 unused3[40]; /* reserved */
-
- uint32 sp0range; /* PCI to internal system bus address space */
- uint32 sp0remap;
- uint32 sp0cfg;
- uint32 sp1range;
- uint32 sp1remap;
- uint32 sp1cfg;
-
- uint32 EndianCfg;
-
- uint32 l2pcfgctl; /* internal system bus to PCI IO/Cfg control */
-#define DIR_CFG_SEL 0x80000000 /* change from PCI I/O access to PCI config access */
-#define DIR_CFG_USEREG 0x40000000 /* use this register info for PCI configuration access */
-#define DEVICE_NUMBER 0x00007C00 /* device number for the PCI configuration access */
-#define FUNC_NUMBER 0x00000300 /* function number for the PCI configuration access */
-#define REG_NUMBER 0x000000FC /* register number for the PCI configuration access */
-#define CONFIG_TYPE 0x00000003 /* configuration type for the PCI configuration access */
-
- uint32 l2pmrange1; /* internal system bus to PCI memory space */
-#define PCI_SIZE_64K 0xFFFF0000
-#define PCI_SIZE_128K 0xFFFE0000
-#define PCI_SIZE_256K 0xFFFC0000
-#define PCI_SIZE_512K 0xFFF80000
-#define PCI_SIZE_1M 0xFFF00000
-#define PCI_SIZE_2M 0xFFE00000
-#define PCI_SIZE_4M 0xFFC00000
-#define PCI_SIZE_8M 0xFF800000
-#define PCI_SIZE_16M 0xFF000000
-#define PCI_SIZE_32M 0xFE000000
- uint32 l2pmbase1; /* kseg0 or kseg1 address & 0x1FFFFFFF */
- uint32 l2pmremap1;
-#define CARDBUS_MEM 0x00000004
-#define MEM_WINDOW_EN 0x00000001
- uint32 l2pmrange2;
- uint32 l2pmbase2;
- uint32 l2pmremap2;
- uint32 l2piorange; /* internal system bus to PCI I/O space */
- uint32 l2piobase;
- uint32 l2pioremap;
-
- uint32 pcimodesel;
-#define PCI2_INT_BUS_RD_PREFECH 0x000000F0
-#define PCI_BAR2_NOSWAP 0x00000002 /* BAR at offset 0x20 */
-#define PCI_BAR1_NOSWAP 0x00000001 /* BAR at affset 0x1c */
-
- uint32 pciintstat; /* PCI interrupt mask/status */
-#define MAILBOX1_SENT 0x08
-#define MAILBOX0_SENT 0x04
-#define MAILBOX1_MSG_RCV 0x02
-#define MAILBOX0_MSG_RCV 0x01
- uint32 locbuscntrl; /* internal system bus control */
-#define DIR_U2P_NOSWAP 0x00000002
-#define EN_PCI_GPIO 0x00000001
- uint32 locintstat; /* internal system bus interrupt mask/status */
-#define CSERR 0x0200
-#define SERR 0x0100
-#define EXT_PCI_INT 0x0080
-#define DIR_FAILED 0x0040
-#define DIR_COMPLETE 0x0020
-#define PCI_CFG 0x0010
- uint32 unused5[7];
-
- uint32 mailbox0;
- uint32 mailbox1;
-
- uint32 pcicfgcntrl; /* internal system bus PCI configuration control */
-#define PCI_CFG_REG_WRITE_EN 0x00000080
-#define PCI_CFG_ADDR 0x0000003C
- uint32 pcicfgdata; /* internal system bus PCI configuration data */
-
- uint32 locch2ctl; /* PCI to interrnal system bus DMA (downstream) local control */
-#define MPI_DMA_HALT 0x00000008 /* idle after finish current memory burst */
-#define MPI_DMA_PKT_HALT 0x00000004 /* idle after an EOP flag is detected */
-#define MPI_DMA_STALL 0x00000002 /* idle after an EOP flag is detected */
-#define MPI_DMA_ENABLE 0x00000001 /* set to enable channel */
- uint32 locch2intStat;
-#define MPI_DMA_NO_DESC 0x00000004 /* no valid descriptors */
-#define MPI_DMA_DONE 0x00000002 /* packet xfer complete */
-#define MPI_DMA_BUFF_DONE 0x00000001 /* buffer done */
- uint32 locch2intMask;
- uint32 unused6;
- uint32 locch2descaddr;
- uint32 locch2status1;
-#define LOCAL_DESC_STATE 0xE0000000
-#define PCI_DESC_STATE 0x1C000000
-#define BYTE_DONE 0x03FFC000
-#define RING_ADDR 0x00003FFF
- uint32 locch2status2;
-#define BUFPTR_OFFSET 0x1FFF0000
-#define PCI_MASTER_STATE 0x000000C0
-#define LOC_MASTER_STATE 0x00000038
-#define CONTROL_STATE 0x00000007
- uint32 unused7;
-
- uint32 locch1Ctl; /*internal system bus to PCI DMA (upstream) local control */
-#define DMA_U2P_LE 0x00000200 /* local bus is little endian */
-#define DMA_U2P_NOSWAP 0x00000100 /* lccal bus is little endian but no data swapped */
- uint32 locch1intstat;
- uint32 locch1intmask;
- uint32 unused8;
- uint32 locch1descaddr;
- uint32 locch1status1;
- uint32 locch1status2;
- uint32 unused9;
-
- uint32 pcich1ctl; /* internal system bus to PCI DMA PCI control */
- uint32 pcich1intstat;
- uint32 pcich1intmask;
- uint32 pcich1descaddr;
- uint32 pcich1status1;
- uint32 pcich1status2;
-
- uint32 pcich2Ctl; /* PCI to internal system bus DMA PCI control */
- uint32 pcich2intstat;
- uint32 pcich2intmask;
- uint32 pcich2descaddr;
- uint32 pcich2status1;
- uint32 pcich2status2;
-
- uint32 perm_id; /* permanent device and vendor id */
- uint32 perm_rev; /* permanent revision id */
-} MpiRegisters;
-
-#define MPI ((volatile MpiRegisters * const) MPI_BASE)
-
-/* PCI configuration address space start offset 0x40 */
-#define BRCM_PCI_CONFIG_TIMER 0x40
-#define BRCM_PCI_CONFIG_TIMER_RETRY_MASK 0x0000FF00
-#define BRCM_PCI_CONFIG_TIMER_TRDY_MASK 0x000000FF
-
-/* USB host non-Open HCI register, USB_HOST_NON_OHCI, bit definitions. */
-#define NON_OHCI_ENABLE_PORT1 0x00000001 /* Use USB port 1 for host, not dev */
-#define NON_OHCI_BYTE_SWAP 0x00000008 /* Swap USB host registers */
-
-#define USBH_NON_OHCI ((volatile unsigned long * const) USB_HOST_NON_OHCI)
-
-#endif
-
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2002 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-//**************************************************************************************
-// File Name : bcmTag.h
-//
-// Description: add tag with validation system to the firmware image file to be uploaded
-// via http
-//
-// Created : 02/28/2002 seanl
-//**************************************************************************************
-
-#ifndef _BCMTAG_H_
-#define _BCMTAG_H_
-
-
-#define BCM_SIG_1 "Broadcom Corporation"
-#define BCM_SIG_2 "ver. 2.0" // was "firmware version 2.0" now it is split 6 char out for chip id.
-
-#define BCM_TAG_VER "6"
-#define BCM_TAG_VER_LAST "26"
-
-// file tag (head) structure all is in clear text except validationTokens (crc, md5, sha1, etc). Total: 128 unsigned chars
-#define TAG_LEN 256
-#define TAG_VER_LEN 4
-#define SIG_LEN 20
-#define SIG_LEN_2 14 // Original second SIG = 20 is now devided into 14 for SIG_LEN_2 and 6 for CHIP_ID
-#define CHIP_ID_LEN 6
-#define IMAGE_LEN 10
-#define ADDRESS_LEN 12
-#define FLAG_LEN 2
-#define TOKEN_LEN 20
-#define BOARD_ID_LEN 16
-#define RESERVED_LEN (TAG_LEN - TAG_VER_LEN - SIG_LEN - SIG_LEN_2 - CHIP_ID_LEN - BOARD_ID_LEN - \
- (4*IMAGE_LEN) - (3*ADDRESS_LEN) - (3*FLAG_LEN) - (2*TOKEN_LEN))
-
-
-// TAG for downloadable image (kernel plus file system)
-typedef struct _FILE_TAG
-{
- unsigned char tagVersion[TAG_VER_LEN]; // tag version. Will be 2 here.
- unsigned char signiture_1[SIG_LEN]; // text line for company info
- unsigned char signiture_2[SIG_LEN_2]; // additional info (can be version number)
- unsigned char chipId[CHIP_ID_LEN]; // chip id
- unsigned char boardId[BOARD_ID_LEN]; // board id
- unsigned char bigEndian[FLAG_LEN]; // if = 1 - big, = 0 - little endia of the host
- unsigned char totalImageLen[IMAGE_LEN]; // the sum of all the following length
- unsigned char cfeAddress[ADDRESS_LEN]; // if non zero, cfe starting address
- unsigned char cfeLen[IMAGE_LEN]; // if non zero, cfe size in clear ASCII text.
- unsigned char rootfsAddress[ADDRESS_LEN]; // if non zero, filesystem starting address
- unsigned char rootfsLen[IMAGE_LEN]; // if non zero, filesystem size in clear ASCII text.
- unsigned char kernelAddress[ADDRESS_LEN]; // if non zero, kernel starting address
- unsigned char kernelLen[IMAGE_LEN]; // if non zero, kernel size in clear ASCII text.
- unsigned char dualImage[FLAG_LEN]; // if 1, dual image
- unsigned char inactiveLen[FLAG_LEN]; // if 1, the image is INACTIVE; if 0, active
- unsigned char reserved[RESERVED_LEN]; // reserved for later use
- unsigned char imageValidationToken[TOKEN_LEN];// image validation token - can be crc, md5, sha; for
- // now will be 4 unsigned char crc
- unsigned char tagValidationToken[TOKEN_LEN]; // validation token for tag(from signiture_1 to end of // mageValidationToken)
-} FILE_TAG, *PFILE_TAG;
-
-#define CRC32_INIT_VALUE 0xffffffff /* Initial CRC32 checksum value */
-#define CRC_LEN 4
-
-// only included if for bcmTag.exe program
-#ifdef BCMTAG_EXE_USE
-
-static unsigned long Crc32_table[256] = {
- 0x00000000, 0x77073096, 0xEE0E612C, 0x990951BA,
- 0x076DC419, 0x706AF48F, 0xE963A535, 0x9E6495A3,
- 0x0EDB8832, 0x79DCB8A4, 0xE0D5E91E, 0x97D2D988,
- 0x09B64C2B, 0x7EB17CBD, 0xE7B82D07, 0x90BF1D91,
- 0x1DB71064, 0x6AB020F2, 0xF3B97148, 0x84BE41DE,
- 0x1ADAD47D, 0x6DDDE4EB, 0xF4D4B551, 0x83D385C7,
- 0x136C9856, 0x646BA8C0, 0xFD62F97A, 0x8A65C9EC,
- 0x14015C4F, 0x63066CD9, 0xFA0F3D63, 0x8D080DF5,
- 0x3B6E20C8, 0x4C69105E, 0xD56041E4, 0xA2677172,
- 0x3C03E4D1, 0x4B04D447, 0xD20D85FD, 0xA50AB56B,
- 0x35B5A8FA, 0x42B2986C, 0xDBBBC9D6, 0xACBCF940,
- 0x32D86CE3, 0x45DF5C75, 0xDCD60DCF, 0xABD13D59,
- 0x26D930AC, 0x51DE003A, 0xC8D75180, 0xBFD06116,
- 0x21B4F4B5, 0x56B3C423, 0xCFBA9599, 0xB8BDA50F,
- 0x2802B89E, 0x5F058808, 0xC60CD9B2, 0xB10BE924,
- 0x2F6F7C87, 0x58684C11, 0xC1611DAB, 0xB6662D3D,
- 0x76DC4190, 0x01DB7106, 0x98D220BC, 0xEFD5102A,
- 0x71B18589, 0x06B6B51F, 0x9FBFE4A5, 0xE8B8D433,
- 0x7807C9A2, 0x0F00F934, 0x9609A88E, 0xE10E9818,
- 0x7F6A0DBB, 0x086D3D2D, 0x91646C97, 0xE6635C01,
- 0x6B6B51F4, 0x1C6C6162, 0x856530D8, 0xF262004E,
- 0x6C0695ED, 0x1B01A57B, 0x8208F4C1, 0xF50FC457,
- 0x65B0D9C6, 0x12B7E950, 0x8BBEB8EA, 0xFCB9887C,
- 0x62DD1DDF, 0x15DA2D49, 0x8CD37CF3, 0xFBD44C65,
- 0x4DB26158, 0x3AB551CE, 0xA3BC0074, 0xD4BB30E2,
- 0x4ADFA541, 0x3DD895D7, 0xA4D1C46D, 0xD3D6F4FB,
- 0x4369E96A, 0x346ED9FC, 0xAD678846, 0xDA60B8D0,
- 0x44042D73, 0x33031DE5, 0xAA0A4C5F, 0xDD0D7CC9,
- 0x5005713C, 0x270241AA, 0xBE0B1010, 0xC90C2086,
- 0x5768B525, 0x206F85B3, 0xB966D409, 0xCE61E49F,
- 0x5EDEF90E, 0x29D9C998, 0xB0D09822, 0xC7D7A8B4,
- 0x59B33D17, 0x2EB40D81, 0xB7BD5C3B, 0xC0BA6CAD,
- 0xEDB88320, 0x9ABFB3B6, 0x03B6E20C, 0x74B1D29A,
- 0xEAD54739, 0x9DD277AF, 0x04DB2615, 0x73DC1683,
- 0xE3630B12, 0x94643B84, 0x0D6D6A3E, 0x7A6A5AA8,
- 0xE40ECF0B, 0x9309FF9D, 0x0A00AE27, 0x7D079EB1,
- 0xF00F9344, 0x8708A3D2, 0x1E01F268, 0x6906C2FE,
- 0xF762575D, 0x806567CB, 0x196C3671, 0x6E6B06E7,
- 0xFED41B76, 0x89D32BE0, 0x10DA7A5A, 0x67DD4ACC,
- 0xF9B9DF6F, 0x8EBEEFF9, 0x17B7BE43, 0x60B08ED5,
- 0xD6D6A3E8, 0xA1D1937E, 0x38D8C2C4, 0x4FDFF252,
- 0xD1BB67F1, 0xA6BC5767, 0x3FB506DD, 0x48B2364B,
- 0xD80D2BDA, 0xAF0A1B4C, 0x36034AF6, 0x41047A60,
- 0xDF60EFC3, 0xA867DF55, 0x316E8EEF, 0x4669BE79,
- 0xCB61B38C, 0xBC66831A, 0x256FD2A0, 0x5268E236,
- 0xCC0C7795, 0xBB0B4703, 0x220216B9, 0x5505262F,
- 0xC5BA3BBE, 0xB2BD0B28, 0x2BB45A92, 0x5CB36A04,
- 0xC2D7FFA7, 0xB5D0CF31, 0x2CD99E8B, 0x5BDEAE1D,
- 0x9B64C2B0, 0xEC63F226, 0x756AA39C, 0x026D930A,
- 0x9C0906A9, 0xEB0E363F, 0x72076785, 0x05005713,
- 0x95BF4A82, 0xE2B87A14, 0x7BB12BAE, 0x0CB61B38,
- 0x92D28E9B, 0xE5D5BE0D, 0x7CDCEFB7, 0x0BDBDF21,
- 0x86D3D2D4, 0xF1D4E242, 0x68DDB3F8, 0x1FDA836E,
- 0x81BE16CD, 0xF6B9265B, 0x6FB077E1, 0x18B74777,
- 0x88085AE6, 0xFF0F6A70, 0x66063BCA, 0x11010B5C,
- 0x8F659EFF, 0xF862AE69, 0x616BFFD3, 0x166CCF45,
- 0xA00AE278, 0xD70DD2EE, 0x4E048354, 0x3903B3C2,
- 0xA7672661, 0xD06016F7, 0x4969474D, 0x3E6E77DB,
- 0xAED16A4A, 0xD9D65ADC, 0x40DF0B66, 0x37D83BF0,
- 0xA9BCAE53, 0xDEBB9EC5, 0x47B2CF7F, 0x30B5FFE9,
- 0xBDBDF21C, 0xCABAC28A, 0x53B39330, 0x24B4A3A6,
- 0xBAD03605, 0xCDD70693, 0x54DE5729, 0x23D967BF,
- 0xB3667A2E, 0xC4614AB8, 0x5D681B02, 0x2A6F2B94,
- 0xB40BBE37, 0xC30C8EA1, 0x5A05DF1B, 0x2D02EF8D
-};
-#endif // BCMTAG_USE
-
-
-#endif // _BCMTAG_H_
-
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2003 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-
-#ifndef __BCM_INTR_H
-#define __BCM_INTR_H
-
-#ifdef __cplusplus
- extern "C" {
-#endif
-
-#if defined(CONFIG_BCM96338)
-#include <6338_intr.h>
-#endif
-#if defined(CONFIG_BCM96345)
-#include <6345_intr.h>
-#endif
-#if defined(CONFIG_BCM96348)
-#include <6348_intr.h>
-#endif
-
-/* defines */
-struct pt_regs;
-typedef int (*FN_HANDLER) (int, void *);
-
-/* prototypes */
-extern void enable_brcm_irq(unsigned int irq);
-extern void disable_brcm_irq(unsigned int irq);
-extern int request_external_irq(unsigned int irq,
- FN_HANDLER handler, unsigned long irqflags,
- const char * devname, void *dev_id);
-extern unsigned int BcmHalMapInterrupt(FN_HANDLER isr, unsigned int param,
- unsigned int interruptId);
-extern void dump_intr_regs(void);
-
-/* compatibility definitions */
-#define BcmHalInterruptEnable(irq) enable_brcm_irq( irq )
-#define BcmHalInterruptDisable(irq) disable_brcm_irq( irq )
-
-#ifdef __cplusplus
- }
-#endif
-
-#endif
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2004 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-
-#ifndef __BCM_MAP_PART_H
-#define __BCM_MAP_PART_H
-
-#if defined(CONFIG_BCM96338)
-#include <6338_map_part.h>
-#endif
-#if defined(CONFIG_BCM96345)
-#include <6345_map_part.h>
-#endif
-#if defined(CONFIG_BCM96348)
-#include <6348_map_part.h>
-#endif
-
-#endif
-
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2004 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-
-//
-// bcmpci.h - bcm96348 PCI, Cardbus, and PCMCIA definition
-//
-#ifndef BCMPCI_H
-#define BCMPCI_H
-
-/* Memory window in internal system bus address space */
-#define BCM_PCI_MEM_BASE 0x08000000
-/* IO window in internal system bus address space */
-#define BCM_PCI_IO_BASE 0x0C000000
-
-#define BCM_PCI_ADDR_MASK 0x1fffffff
-
-/* Memory window size (range) */
-#define BCM_PCI_MEM_SIZE_16MB 0x01000000
-/* IO window size (range) */
-#define BCM_PCI_IO_SIZE_64KB 0x00010000
-
-/* PCI Configuration and I/O space acesss */
-#define BCM_PCI_CFG(d, f, o) ( (d << 11) | (f << 8) | (o/4 << 2) )
-
-/* fake USB PCI slot */
-#define USB_HOST_SLOT 9
-#define USB_BAR0_MEM_SIZE 0x0800
-
-#define BCM_HOST_MEM_SPACE1 0x10000000
-#define BCM_HOST_MEM_SPACE2 0x00000000
-
-/*
- * EBI bus clock is 33MHz and share with PCI bus
- * each clock cycle is 30ns.
- */
-/* attribute memory access wait cnt for 4306 */
-#define PCMCIA_ATTR_CE_HOLD 3 // data hold time 70ns
-#define PCMCIA_ATTR_CE_SETUP 3 // data setup time 50ns
-#define PCMCIA_ATTR_INACTIVE 6 // time between read/write cycles 180ns. For the total cycle time 600ns (cnt1+cnt2+cnt3+cnt4)
-#define PCMCIA_ATTR_ACTIVE 10 // OE/WE pulse width 300ns
-
-/* common memory access wait cnt for 4306 */
-#define PCMCIA_MEM_CE_HOLD 1 // data hold time 30ns
-#define PCMCIA_MEM_CE_SETUP 1 // data setup time 30ns
-#define PCMCIA_MEM_INACTIVE 2 // time between read/write cycles 40ns. For the total cycle time 250ns (cnt1+cnt2+cnt3+cnt4)
-#define PCMCIA_MEM_ACTIVE 5 // OE/WE pulse width 150ns
-
-#define PCCARD_VCC_MASK 0x00070000 // Mask Reset also
-#define PCCARD_VCC_33V 0x00010000
-#define PCCARD_VCC_50V 0x00020000
-
-typedef enum {
- MPI_CARDTYPE_NONE, // No Card in slot
- MPI_CARDTYPE_PCMCIA, // 16-bit PCMCIA card in slot
- MPI_CARDTYPE_CARDBUS, // 32-bit CardBus card in slot
-} CardType;
-
-#define CARDBUS_SLOT 0 // Slot 0 is default for CardBus
-
-#define pcmciaAttrOffset 0x00200000
-#define pcmciaMemOffset 0x00000000
-// Needs to be right above PCI I/O space. Give 0x8000 (32K) to PCMCIA.
-#define pcmciaIoOffset (BCM_PCI_IO_BASE + 0x80000)
-// Base Address is that mapped into the MPI ChipSelect registers.
-// UBUS bridge MemoryWindow 0 outputs a 0x00 for the base.
-#define pcmciaBase 0xbf000000
-#define pcmciaAttr (pcmciaAttrOffset | pcmciaBase)
-#define pcmciaMem (pcmciaMemOffset | pcmciaBase)
-#define pcmciaIo (pcmciaIoOffset | pcmciaBase)
-
-#endif
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2002 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-
-//
-// bcmtypes.h - misc useful typedefs
-//
-#ifndef BCMTYPES_H
-#define BCMTYPES_H
-
-// These are also defined in typedefs.h in the application area, so I need to
-// protect against re-definition.
-
-#ifndef _TYPEDEFS_H_
-typedef unsigned char uint8;
-typedef unsigned short uint16;
-typedef unsigned long uint32;
-typedef signed char int8;
-typedef signed short int16;
-typedef signed long int32;
-#endif
-
-typedef unsigned char byte;
-// typedef unsigned long sem_t;
-
-typedef unsigned long HANDLE,*PULONG,DWORD,*PDWORD;
-typedef signed long LONG,*PLONG;
-
-typedef unsigned int *PUINT;
-typedef signed int INT;
-
-typedef unsigned short *PUSHORT;
-typedef signed short SHORT,*PSHORT;
-typedef unsigned short WORD,*PWORD;
-
-typedef unsigned char *PUCHAR;
-typedef signed char *PCHAR;
-
-typedef void *PVOID;
-
-typedef unsigned char BOOLEAN, *PBOOL, *PBOOLEAN;
-
-typedef unsigned char BYTE,*PBYTE;
-
-//#ifndef __GNUC__
-//The following has been defined in Vxworks internally: vxTypesOld.h
-//redefine under vxworks will cause error
-typedef signed int *PINT;
-
-typedef signed char INT8;
-typedef signed short INT16;
-typedef signed long INT32;
-
-typedef unsigned char UINT8;
-typedef unsigned short UINT16;
-typedef unsigned long UINT32;
-
-typedef unsigned char UCHAR;
-typedef unsigned short USHORT;
-typedef unsigned int UINT;
-typedef unsigned long ULONG;
-
-typedef void VOID;
-typedef unsigned char BOOL;
-
-//#endif /* __GNUC__ */
-
-
-// These are also defined in typedefs.h in the application area, so I need to
-// protect against re-definition.
-#ifndef TYPEDEFS_H
-
-// Maximum and minimum values for a signed 16 bit integer.
-#define MAX_INT16 32767
-#define MIN_INT16 -32768
-
-// Useful for true/false return values. This uses the
-// Taligent notation (k for constant).
-typedef enum
-{
- kFalse = 0,
- kTrue = 1
-} Bool;
-
-#endif
-
-/* macros to protect against unaligned accesses */
-
-#if 0
-/* first arg is an address, second is a value */
-#define PUT16( a, d ) { \
- *((byte *)a) = (byte)((d)>>8); \
- *(((byte *)a)+1) = (byte)(d); \
-}
-
-#define PUT32( a, d ) { \
- *((byte *)a) = (byte)((d)>>24); \
- *(((byte *)a)+1) = (byte)((d)>>16); \
- *(((byte *)a)+2) = (byte)((d)>>8); \
- *(((byte *)a)+3) = (byte)(d); \
-}
-
-/* first arg is an address, returns a value */
-#define GET16( a ) ( \
- (*((byte *)a) << 8) | \
- (*(((byte *)a)+1)) \
-)
-
-#define GET32( a ) ( \
- (*((byte *)a) << 24) | \
- (*(((byte *)a)+1) << 16) | \
- (*(((byte *)a)+2) << 8) | \
- (*(((byte *)a)+3)) \
-)
-#endif
-
-#ifndef YES
-#define YES 1
-#endif
-
-#ifndef NO
-#define NO 0
-#endif
-
-#ifndef IN
-#define IN
-#endif
-
-#ifndef OUT
-#define OUT
-#endif
-
-#ifndef TRUE
-#define TRUE 1
-#endif
-
-#ifndef FALSE
-#define FALSE 0
-#endif
-
-#define READ32(addr) (*(volatile UINT32 *)((ULONG)&addr))
-#define READ16(addr) (*(volatile UINT16 *)((ULONG)&addr))
-#define READ8(addr) (*(volatile UINT8 *)((ULONG)&addr))
-
-#endif
+++ /dev/null
-/*
-<:copyright-gpl
- Copyright 2002 Broadcom Corp. All Rights Reserved.
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
- published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- for more details.
-
- You should have received a copy of the GNU General Public License along
- with this program; if not, write to the Free Software Foundation, Inc.,
- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
-:>
-*/
-/***********************************************************************/
-/* */
-/* MODULE: board.h */
-/* DATE: 97/02/18 */
-/* PURPOSE: Board specific information. This module should include */
-/* all base device addresses and board specific macros. */
-/* */
-/***********************************************************************/
-#ifndef _BOARD_H
-#define _BOARD_H
-
-/*****************************************************************************/
-/* Misc board definitions */
-/*****************************************************************************/
-
-#define DYING_GASP_API
-
-/*****************************************************************************/
-/* Physical Memory Map */
-/*****************************************************************************/
-
-#define PHYS_DRAM_BASE 0x00000000 /* Dynamic RAM Base */
-#define PHYS_FLASH_BASE 0x1FC00000 /* Flash Memory */
-
-/*****************************************************************************/
-/* Note that the addresses above are physical addresses and that programs */
-/* have to use converted addresses defined below: */
-/*****************************************************************************/
-#define DRAM_BASE (0x80000000 | PHYS_DRAM_BASE) /* cached DRAM */
-#define DRAM_BASE_NOCACHE (0xA0000000 | PHYS_DRAM_BASE) /* uncached DRAM */
-#define FLASH_BASE (0xA0000000 | PHYS_FLASH_BASE) /* uncached Flash */
-
-/*****************************************************************************/
-/* Select the PLL value to get the desired CPU clock frequency. */
-/* */
-/* */
-/*****************************************************************************/
-#define FPERIPH 50000000
-
-#define ONEK 1024
-#define BLK64K (64*ONEK)
-#define FLASH45_BLKS_BOOT_ROM 1
-#define FLASH45_LENGTH_BOOT_ROM (FLASH45_BLKS_BOOT_ROM * BLK64K)
-#define FLASH_RESERVED_AT_END (64*ONEK) /*reserved for PSI, scratch pad*/
-
-/*****************************************************************************/
-/* Note that the addresses above are physical addresses and that programs */
-/* have to use converted addresses defined below: */
-/*****************************************************************************/
-#define DRAM_BASE (0x80000000 | PHYS_DRAM_BASE) /* cached DRAM */
-#define DRAM_BASE_NOCACHE (0xA0000000 | PHYS_DRAM_BASE) /* uncached DRAM */
-#define FLASH_BASE (0xA0000000 | PHYS_FLASH_BASE) /* uncached Flash */
-
-/*****************************************************************************/
-/* Select the PLL value to get the desired CPU clock frequency. */
-/* */
-/* */
-/*****************************************************************************/
-#define FPERIPH 50000000
-
-#define SDRAM_TYPE_ADDRESS_OFFSET 16
-#define NVRAM_DATA_OFFSET 0x0580
-#define NVRAM_DATA_ID 0x0f1e2d3c
-#define BOARD_SDRAM_TYPE *(unsigned long *) \
- (FLASH_BASE + SDRAM_TYPE_ADDRESS_OFFSET)
-
-#define ONEK 1024
-#define BLK64K (64*ONEK)
-
-// nvram and psi flash definitions for 45
-#define FLASH45_LENGTH_NVRAM ONEK // 1k nvram
-#define NVRAM_PSI_DEFAULT 24 // default psi in K byes
-
-/*****************************************************************************/
-/* NVRAM Offset and definition */
-/*****************************************************************************/
-
-#define NVRAM_VERSION_NUMBER 2
-#define NVRAM_VERSION_NUMBER_ADDRESS 0
-
-#define NVRAM_BOOTLINE_LEN 256
-#define NVRAM_BOARD_ID_STRING_LEN 16
-#define NVRAM_MAC_ADDRESS_LEN 6
-#define NVRAM_MAC_COUNT_MAX 32
-
-/*****************************************************************************/
-/* Misc Offsets */
-/*****************************************************************************/
-
-#define CFE_VERSION_OFFSET 0x0570
-#define CFE_VERSION_MARK_SIZE 5
-#define CFE_VERSION_SIZE 5
-
-typedef struct
-{
- unsigned long ulVersion;
- char szBootline[NVRAM_BOOTLINE_LEN];
- char szBoardId[NVRAM_BOARD_ID_STRING_LEN];
- unsigned long ulReserved1[2];
- unsigned long ulNumMacAddrs;
- unsigned char ucaBaseMacAddr[NVRAM_MAC_ADDRESS_LEN];
- char chReserved[2];
- unsigned long ulCheckSum;
-} NVRAM_DATA, *PNVRAM_DATA;
-
-
-/*****************************************************************************/
-/* board ioctl calls for flash, led and some other utilities */
-/*****************************************************************************/
-
-
-/* Defines. for board driver */
-#define BOARD_IOCTL_MAGIC 'B'
-#define BOARD_DRV_MAJOR 206
-
-#define MAC_ADDRESS_ANY (unsigned long) -1
-
-#define BOARD_IOCTL_FLASH_INIT \
- _IOWR(BOARD_IOCTL_MAGIC, 0, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_FLASH_WRITE \
- _IOWR(BOARD_IOCTL_MAGIC, 1, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_FLASH_READ \
- _IOWR(BOARD_IOCTL_MAGIC, 2, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_GET_NR_PAGES \
- _IOWR(BOARD_IOCTL_MAGIC, 3, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_DUMP_ADDR \
- _IOWR(BOARD_IOCTL_MAGIC, 4, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_SET_MEMORY \
- _IOWR(BOARD_IOCTL_MAGIC, 5, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_MIPS_SOFT_RESET \
- _IOWR(BOARD_IOCTL_MAGIC, 6, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_LED_CTRL \
- _IOWR(BOARD_IOCTL_MAGIC, 7, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_GET_ID \
- _IOWR(BOARD_IOCTL_MAGIC, 8, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_GET_MAC_ADDRESS \
- _IOWR(BOARD_IOCTL_MAGIC, 9, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_RELEASE_MAC_ADDRESS \
- _IOWR(BOARD_IOCTL_MAGIC, 10, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_GET_PSI_SIZE \
- _IOWR(BOARD_IOCTL_MAGIC, 11, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_GET_SDRAM_SIZE \
- _IOWR(BOARD_IOCTL_MAGIC, 12, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_SET_MONITOR_FD \
- _IOWR(BOARD_IOCTL_MAGIC, 13, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_WAKEUP_MONITOR_TASK \
- _IOWR(BOARD_IOCTL_MAGIC, 14, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_GET_BOOTLINE \
- _IOWR(BOARD_IOCTL_MAGIC, 15, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_SET_BOOTLINE \
- _IOWR(BOARD_IOCTL_MAGIC, 16, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_GET_BASE_MAC_ADDRESS \
- _IOWR(BOARD_IOCTL_MAGIC, 17, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_GET_CHIP_ID \
- _IOWR(BOARD_IOCTL_MAGIC, 18, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_GET_NUM_ENET \
- _IOWR(BOARD_IOCTL_MAGIC, 19, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_GET_CFE_VER \
- _IOWR(BOARD_IOCTL_MAGIC, 20, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_GET_ENET_CFG \
- _IOWR(BOARD_IOCTL_MAGIC, 21, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_GET_WLAN_ANT_INUSE \
- _IOWR(BOARD_IOCTL_MAGIC, 22, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_SET_TRIGGER_EVENT \
- _IOWR(BOARD_IOCTL_MAGIC, 23, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_GET_TRIGGER_EVENT \
- _IOWR(BOARD_IOCTL_MAGIC, 24, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_UNSET_TRIGGER_EVENT \
- _IOWR(BOARD_IOCTL_MAGIC, 25, BOARD_IOCTL_PARMS)
-
-#define BOARD_IOCTL_SET_SES_LED \
- _IOWR(BOARD_IOCTL_MAGIC, 26, BOARD_IOCTL_PARMS)
-
-//<<JUNHON, 2004/09/15, get reset button status , tim hou , 05/04/12
-#define RESET_BUTTON_UP 1
-#define RESET_BUTTON_PRESSDOWN 0
-#define BOARD_IOCTL_GET_RESETHOLD \
- _IOWR(BOARD_IOCTL_MAGIC, 27, BOARD_IOCTL_PARMS)
-//>>JUNHON, 2004/09/15
-
-// for the action in BOARD_IOCTL_PARMS for flash operation
-typedef enum
-{
- PERSISTENT,
- NVRAM,
- BCM_IMAGE_CFE,
- BCM_IMAGE_FS,
- BCM_IMAGE_KERNEL,
- BCM_IMAGE_WHOLE,
- SCRATCH_PAD,
- FLASH_SIZE,
-} BOARD_IOCTL_ACTION;
-
-
-typedef struct boardIoctParms
-{
- char *string;
- char *buf;
- int strLen;
- int offset;
- BOARD_IOCTL_ACTION action; /* flash read/write: nvram, persistent, bcm image */
- int result;
-} BOARD_IOCTL_PARMS;
-
-
-// LED defines
-typedef enum
-{
- kLedAdsl,
- kLedWireless,
- kLedUsb,
- kLedHpna,
- kLedWanData,
- kLedPPP,
- kLedVoip,
- kLedSes,
- kLedLan,
- kLedSelfTest,
- kLedEnd, // NOTE: Insert the new led name before this one. Alway stay at the end.
-} BOARD_LED_NAME;
-
-typedef enum
-{
- kLedStateOff, /* turn led off */
- kLedStateOn, /* turn led on */
- kLedStateFail, /* turn led on red */
- kLedStateBlinkOnce, /* blink once, ~100ms and ignore the same call during the 100ms period */
- kLedStateSlowBlinkContinues, /* slow blink continues at ~600ms interval */
- kLedStateFastBlinkContinues, /* fast blink continues at ~200ms interval */
-} BOARD_LED_STATE;
-
-
-// virtual and physical map pair defined in board.c
-typedef struct ledmappair
-{
- BOARD_LED_NAME ledName; // virtual led name
- BOARD_LED_STATE ledInitState; // initial led state when the board boots.
- unsigned short ledMask; // physical GPIO pin mask
- unsigned short ledActiveLow; // reset bit to turn on LED
- unsigned short ledMaskFail; // physical GPIO pin mask for state failure
- unsigned short ledActiveLowFail;// reset bit to turn on LED
-} LED_MAP_PAIR, *PLED_MAP_PAIR;
-
-typedef void (*HANDLE_LED_FUNC)(BOARD_LED_NAME ledName, BOARD_LED_STATE ledState);
-
-/* Flash storage address information that is determined by the flash driver. */
-typedef struct flashaddrinfo
-{
- int flash_persistent_start_blk;
- int flash_persistent_number_blk;
- int flash_persistent_length;
- unsigned long flash_persistent_blk_offset;
- int flash_scratch_pad_start_blk; // start before psi (SP_BUF_LEN)
- int flash_scratch_pad_number_blk;
- int flash_scratch_pad_length;
- unsigned long flash_scratch_pad_blk_offset;
- int flash_nvram_start_blk;
- int flash_nvram_number_blk;
- int flash_nvram_length;
- unsigned long flash_nvram_blk_offset;
-} FLASH_ADDR_INFO, *PFLASH_ADDR_INFO;
-
-// scratch pad defines
-/* SP - Persisten Scratch Pad format:
- sp header : 32 bytes
- tokenId-1 : 8 bytes
- tokenId-1 len : 4 bytes
- tokenId-1 data
- ....
- tokenId-n : 8 bytes
- tokenId-n len : 4 bytes
- tokenId-n data
-*/
-
-#define MAGIC_NUM_LEN 8
-#define MAGIC_NUMBER "gOGoBrCm"
-#define TOKEN_NAME_LEN 16
-#define SP_VERSION 1
-#define SP_MAX_LEN 8 * 1024 // 8k buf before psi
-#define SP_RESERVERD 16
-
-typedef struct _SP_HEADER
-{
- char SPMagicNum[MAGIC_NUM_LEN]; // 8 bytes of magic number
- int SPVersion; // version number
- int SPUsedLen; // used sp len
- char SPReserved[SP_RESERVERD]; // reservied, total 32 bytes
-} SP_HEADER, *PSP_HEADER;
-
-typedef struct _TOKEN_DEF
-{
- char tokenName[TOKEN_NAME_LEN];
- int tokenLen;
-} SP_TOKEN, *PSP_TOKEN;
-
-
-/*****************************************************************************/
-/* Function Prototypes */
-/*****************************************************************************/
-#if !defined(__ASM_ASM_H)
-void dumpaddr( unsigned char *pAddr, int nLen );
-
-int kerSysNvRamGet(char *string, int strLen, int offset);
-int kerSysNvRamSet(char *string, int strLen, int offset);
-int kerSysPersistentGet(char *string, int strLen, int offset);
-int kerSysPersistentSet(char *string, int strLen, int offset);
-int kerSysScratchPadGet(char *tokName, char *tokBuf, int tokLen);
-int kerSysScratchPadSet(char *tokName, char *tokBuf, int tokLen);
-int kerSysBcmImageSet( int flash_start_addr, char *string, int size);
-int kerSysGetMacAddress( unsigned char *pucaAddr, unsigned long ulId );
-int kerSysReleaseMacAddress( unsigned char *pucaAddr );
-int kerSysGetSdramSize( void );
-void kerSysGetBootline(char *string, int strLen);
-void kerSysSetBootline(char *string, int strLen);
-void kerSysMipsSoftReset(void);
-void kerSysLedCtrl(BOARD_LED_NAME, BOARD_LED_STATE);
-void kerSysLedRegisterHwHandler( BOARD_LED_NAME, HANDLE_LED_FUNC, int );
-int kerSysFlashSizeGet(void);
-void kerSysRegisterDyingGaspHandler(char *devname, void *cbfn, void *context);
-void kerSysDeregisterDyingGaspHandler(char *devname);
-void kerSysWakeupMonitorTask( void );
-#endif
-
-#define BOOT_CFE 0
-#define BOOT_REDBOOT 1
-
-extern int boot_loader_type;
-
-#endif /* _BOARD_H */
-
+++ /dev/null
-#define ADSL_SDRAM_IMAGE_SIZE (384*1024)
-
-#define BOOT_LOADER_UNKNOWN 0
-#define BOOT_LOADER_CFE 1
-#define BOOT_LOADER_REDBOOT 2
-#define BOOT_LOADER_CFE2 3
-#define BOOT_LOADER_LAST 3
+++ /dev/null
-#ifndef __ASM_MACH_BCM963XX_CPU_FEATURE_OVERRIDES_H
-#define __ASM_MACH_BCM963XX_CPU_FEATURE_OVERRIDES_H
-
-#define cpu_has_tlb 1
-#define cpu_has_4kex 4
-#define cpu_has_4ktlb 8
-#define cpu_has_fpu 0
-#define cpu_has_32fpr 0
-#define cpu_has_counter 0x40
-#define cpu_has_watch 0
-#define cpu_has_mips16 0
-#define cpu_has_divec 0x200
-#define cpu_has_vce 0
-#define cpu_has_cache_cdex_p 0
-#define cpu_has_cache_cdex_s 0
-#define cpu_has_prefetch 0x40000
-#define cpu_has_mcheck 0x2000
-#define cpu_has_ejtag 0x4000
-#define cpu_has_llsc 0x10000
-#define cpu_has_vtag_icache 0
-#define cpu_has_dc_aliases 0
-#define cpu_has_ic_fills_f_dc 0
-
-#define cpu_has_nofpuex 0
-#define cpu_has_64bits 0
-#define cpu_has_64bit_zero_reg 0
-#define cpu_has_64bit_gp_regs 0
-#define cpu_has_64bit_addresses 0
-
-#define cpu_has_subset_pcaches 0
-
-#define cpu_dcache_line_size() 16
-#define cpu_icache_line_size() 16
-#define cpu_scache_line_size() 0
-
-#endif /* __ASM_MACH_BCM963XX_CPU_FEATURE_OVERRIDES_H */
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2002, 2004, 2007 by Ralf Baechle <ralf@linux-mips.org>
- */
-#ifndef __ASM_MIPS_MACH_BCM963XX_WAR_H
-#define __ASM_MIPS_MACH_BCM963XX_WAR_H
-
-#define R4600_V1_INDEX_ICACHEOP_WAR 0
-#define R4600_V1_HIT_CACHEOP_WAR 0
-#define R4600_V2_HIT_CACHEOP_WAR 0
-#define R5432_CP0_INTERRUPT_WAR 0
-#define BCM1250_M3_WAR 0
-#define SIBYTE_1956_WAR 0
-#define MIPS4K_ICACHE_REFILL_WAR 0
-#define MIPS_CACHE_SYNC_WAR 0
-#define TX49XX_ICACHE_INDEX_INV_WAR 0
-#define RM9000_CDEX_SMP_WAR 0
-#define ICACHE_REFILLS_WORKAROUND_WAR 0
-#define R10000_LLSC_WAR 0
-#define MIPS34K_MISSED_ITLB_WAR 0
-
-#endif /* __ASM_MIPS_MACH_BCM963XX_WAR_H */
+++ /dev/null
-#ifndef _LINUX_ATMRT2684_H
-#define _LINUX_ATMRT2684_H
-
-#include <linux/atm.h>
-#include <linux/if.h> /* For IFNAMSIZ */
-
-#define RT2684_ENCAPS_NULL (0) /* VC-mux */
-#define RT2684_ENCAPS_LLC (1)
-#define RT2684_ENCAPS_AUTODETECT (2) /* Unsuported */
-
-/*
- * This is for the ATM_NEWBACKENDIF call - these are like socket families:
- * the first element of the structure is the backend number and the rest
- * is per-backend specific
- */
-struct atm_newif_rt2684 {
- atm_backend_t backend_num; /* ATM_BACKEND_RT2684 */
- char ifname[IFNAMSIZ];
-};
-
-/*
- * This structure is used to specify a rt2684 interface - either by a
- * positive integer (returned by ATM_NEWBACKENDIF) or the interfaces name
- */
-#define RT2684_FIND_BYNOTHING (0)
-#define RT2684_FIND_BYNUM (1)
-#define RT2684_FIND_BYIFNAME (2)
-struct rt2684_if_spec {
- int method; /* RT2684_FIND_* */
- union {
- char ifname[IFNAMSIZ];
- int devnum;
- } spec;
-};
-
-/*
- * This is for the ATM_SETBACKEND call - these are like socket families:
- * the first element of the structure is the backend number and the rest
- * is per-backend specific
- */
-struct atm_backend_rt2684 {
- atm_backend_t backend_num; /* ATM_BACKEND_RT2684 */
- struct rt2684_if_spec ifspec;
- unsigned char encaps; /* RT2684_ENCAPS_* */
-};
-
-
-#endif /* _LINUX_ATMRT2684_H */
+++ /dev/null
-From 2b2b8e163d28646cbbfde81c900fbb57d6572a11 Mon Sep 17 00:00:00 2001
-From: Axel Gembe <ago@bastart.eu.org>
-Date: Thu, 15 May 2008 11:00:43 +0200
-Subject: [PATCH] bcm963xx: board support
-
-
-Signed-off-by: Axel Gembe <ago@bastart.eu.org>
----
- arch/mips/Kconfig | 11 +++++++++++
- arch/mips/Makefile | 4 ++++
- arch/mips/kernel/cpu-probe.c | 16 ++++++++++++++++
- arch/mips/mm/c-r4k.c | 7 +++++++
- arch/mips/mm/tlbex.c | 4 ++++
- arch/mips/pci/Makefile | 1 +
- include/asm-mips/bootinfo.h | 12 ++++++++++++
- include/asm-mips/cpu.h | 7 ++++++-
- 8 files changed, 61 insertions(+), 1 deletions(-)
-
---- a/arch/mips/Kconfig
-+++ b/arch/mips/Kconfig
-@@ -59,6 +59,17 @@
- help
- Support for BCM47XX based boards
-
-+config BCM963XX
-+ bool "Support for Broadcom BCM963xx SoC"
-+ select SYS_SUPPORTS_32BIT_KERNEL
-+ select SYS_SUPPORTS_BIG_ENDIAN
-+ select SYS_HAS_CPU_MIPS32_R1
-+ select HW_HAS_PCI
-+ select DMA_NONCOHERENT
-+ select IRQ_CPU
-+ help
-+ This is a fmaily of boards based on the Broadcom MIPS32
-+
- config MIPS_COBALT
- bool "Cobalt Server"
- select CEVT_R4K
---- a/arch/mips/Makefile
-+++ b/arch/mips/Makefile
-@@ -560,6 +560,10 @@
- cflags-$(CONFIG_BCM47XX) += -Iinclude/asm-mips/mach-bcm47xx
- load-$(CONFIG_BCM47XX) := 0xffffffff80001000
-
-+core-$(CONFIG_BCM963XX) += arch/mips/bcm963xx/
-+cflags-$(CONFIG_BCM963XX) += -Iinclude/asm-mips/mach-bcm963xx
-+load-$(CONFIG_BCM963XX) := 0xffffffff8001000
-+
- #
- # SNI RM
- #
---- a/arch/mips/kernel/cpu-probe.c
-+++ b/arch/mips/kernel/cpu-probe.c
-@@ -803,6 +803,21 @@
- case PRID_IMP_BCM4710:
- c->cputype = CPU_BCM4710;
- break;
-+// case PRID_IMP_BCM6338:
-+// c->cputype = CPU_BCM6338;
-+// break;
-+ case PRID_IMP_BCM6345:
-+ c->cputype = CPU_BCM6345;
-+ break;
-+ case PRID_IMP_BCM6348:
-+ c->cputype = CPU_BCM6348;
-+ break;
-+ case PRID_IMP_BCM6358:
-+ c->cputype = CPU_BCM6358;
-+ break;
-+ case PRID_IMP_BCM3350:
-+ c->cputype = CPU_BCM3350;
-+ break;
- default:
- c->cputype = CPU_UNKNOWN;
- break;
-@@ -887,6 +902,11 @@
- case CPU_SR71000: name = "Sandcraft SR71000"; break;
- case CPU_BCM3302: name = "Broadcom BCM3302"; break;
- case CPU_BCM4710: name = "Broadcom BCM4710"; break;
-+ case CPU_BCM6338: name = "Broadcom BCM6338"; break;
-+ case CPU_BCM6345: name = "Broadcom BCM6345"; break;
-+ case CPU_BCM6348: name = "Broadcom BCM6348"; break;
-+ case CPU_BCM6358: name = "Broadcom BCM6358"; break;
-+ case CPU_BCM3350: name = "Broadcom BCM3350"; break;
- case CPU_PR4450: name = "Philips PR4450"; break;
- case CPU_LOONGSON2: name = "ICT Loongson-2"; break;
- default:
---- a/arch/mips/mm/c-r4k.c
-+++ b/arch/mips/mm/c-r4k.c
-@@ -882,6 +882,13 @@
- if (!(config & MIPS_CONF_M))
- panic("Don't know how to probe P-caches on this cpu.");
-
-+ if (c->cputype == CPU_BCM6338 || c->cputype == CPU_BCM6345 || c->cputype == CPU_BCM6348 || c->cputype == CPU_BCM6358 || c->cputype == CPU_BCM3350)
-+ {
-+ printk("bcm963xx: enabling icache and dcache...\n");
-+ /* Enable caches */
-+ write_c0_diag(read_c0_diag() | 0xC0000000);
-+ }
-+
- /*
- * So we seem to be a MIPS32 or MIPS64 CPU
- * So let's probe the I-cache ...
---- a/arch/mips/mm/tlbex.c
-+++ b/arch/mips/mm/tlbex.c
-@@ -315,6 +315,11 @@
- case CPU_25KF:
- case CPU_BCM3302:
- case CPU_BCM4710:
-+// case CPU_BCM6338:
-+ case CPU_BCM6345:
-+ case CPU_BCM6348:
-+ case CPU_BCM6358:
-+ case CPU_BCM3350:
- case CPU_LOONGSON2:
- if (m4kc_tlbp_war())
- uasm_i_nop(p);
---- a/arch/mips/pci/Makefile
-+++ b/arch/mips/pci/Makefile
-@@ -48,3 +48,4 @@
- obj-$(CONFIG_VICTOR_MPC30X) += fixup-mpc30x.o
- obj-$(CONFIG_ZAO_CAPCELLA) += fixup-capcella.o
- obj-$(CONFIG_WR_PPMC) += fixup-wrppmc.o
-+obj-$(CONFIG_BCM963XX) += fixup-bcm96348.o pci-bcm96348.o ops-bcm96348.o
---- a/include/asm-mips/bootinfo.h
-+++ b/include/asm-mips/bootinfo.h
-@@ -94,6 +94,19 @@
- #define MACH_MSP7120_FPGA 5 /* PMC-Sierra MSP7120 Emulation */
- #define MACH_MSP_OTHER 255 /* PMC-Sierra unknown board type */
-
-+#define MACH_WRPPMC 1
-+
-+/*
-+ * Valid machtype for group Broadcom
-+ */
-+#define MACH_GROUP_BRCM 23 /* Broadcom */
-+#define MACH_BCM47XX 1 /* Broadcom BCM47XX */
-+#define MACH_BCM96338 2
-+#define MACH_BCM96345 3
-+#define MACH_BCM96348 4
-+#define MACH_BCM96358 5
-+#define MACH_BCM3350 6
-+
- #define CL_SIZE COMMAND_LINE_SIZE
-
- extern char *system_type;
---- a/include/asm-mips/cpu.h
-+++ b/include/asm-mips/cpu.h
-@@ -111,6 +111,11 @@
-
- #define PRID_IMP_BCM4710 0x4000
- #define PRID_IMP_BCM3302 0x9000
-+//#define PRID_IMP_BCM6338 0x9000
-+#define PRID_IMP_BCM6345 0x8000
-+#define PRID_IMP_BCM6348 0x9100
-+#define PRID_IMP_BCM6358 0xA000
-+#define PRID_IMP_BCM3350 0x28000
-
- /*
- * Definitions for 7:0 on legacy processors
-@@ -196,7 +201,8 @@
- */
- CPU_4KC, CPU_4KEC, CPU_4KSC, CPU_24K, CPU_34K, CPU_74K, CPU_AU1000,
- CPU_AU1100, CPU_AU1200, CPU_AU1210, CPU_AU1250, CPU_AU1500, CPU_AU1550,
-- CPU_PR4450, CPU_BCM3302, CPU_BCM4710,
-+ CPU_PR4450, CPU_BCM3302, CPU_BCM4710, CPU_BCM6338, CPU_BCM6345, CPU_BCM6348,
-+ CPU_BCM6358, CPU_BCM3350,
-
- /*
- * MIPS64 class processors
+++ /dev/null
-From 53bc5316c1123689dddf2c78a4cdfd15834237e8 Mon Sep 17 00:00:00 2001
-From: Axel Gembe <ago@bastart.eu.org>
-Date: Mon, 12 May 2008 18:53:47 +0200
-Subject: [PATCH] bcm963xx: serial port support
-
-
-Signed-off-by: Axel Gembe <ago@bastart.eu.org>
----
- drivers/serial/Makefile | 1 +
- 1 files changed, 1 insertions(+), 0 deletions(-)
-
---- a/drivers/serial/Makefile
-+++ b/drivers/serial/Makefile
-@@ -67,3 +67,4 @@
- obj-$(CONFIG_SERIAL_OF_PLATFORM) += of_serial.o
- obj-$(CONFIG_SERIAL_KS8695) += serial_ks8695.o
- obj-$(CONFIG_SERIAL_QE) += ucc_uart.o
-+obj-$(CONFIG_BCM963XX) += bcm63xx_cons.o
+++ /dev/null
-From e734ace5baa04e0e8af1d4483475fbd6bd2b32a1 Mon Sep 17 00:00:00 2001
-From: Axel Gembe <ago@bastart.eu.org>
-Date: Mon, 12 May 2008 18:54:09 +0200
-Subject: [PATCH] bcm963xx: flashmap support
-
-
-Signed-off-by: Axel Gembe <ago@bastart.eu.org>
----
- drivers/mtd/maps/Kconfig | 7 +++++++
- drivers/mtd/maps/Makefile | 1 +
- drivers/mtd/redboot.c | 13 ++++++++++---
- 3 files changed, 18 insertions(+), 3 deletions(-)
-
---- a/drivers/mtd/maps/Kconfig
-+++ b/drivers/mtd/maps/Kconfig
-@@ -262,6 +262,13 @@
- Flash memory access on 4G Systems MTX-1 Board. If you have one of
- these boards and would like to use the flash chips on it, say 'Y'.
-
-+config MTD_BCM963XX
-+ tristate "BCM963xx Flash device"
-+ depends on MIPS && BCM963XX
-+ help
-+ Flash memory access on BCM963xx boards. Currently only works with
-+ RedBoot and CFE.
-+
- config MTD_DILNETPC
- tristate "CFI Flash device mapped on DIL/Net PC"
- depends on X86 && MTD_CONCAT && MTD_PARTITIONS && MTD_CFI_INTELEXT
---- a/drivers/mtd/maps/Makefile
-+++ b/drivers/mtd/maps/Makefile
-@@ -68,3 +68,4 @@
- obj-$(CONFIG_MTD_OMAP_NOR) += omap_nor.o
- obj-$(CONFIG_MTD_MTX1) += mtx-1_flash.o
- obj-$(CONFIG_MTD_INTEL_VR_NOR) += intel_vr_nor.o
-+obj-$(CONFIG_MTD_BCM963XX) += bcm963xx-flash.o
---- a/drivers/mtd/redboot.c
-+++ b/drivers/mtd/redboot.c
-@@ -39,7 +39,7 @@
- return 1;
- }
-
--static int parse_redboot_partitions(struct mtd_info *master,
-+int parse_redboot_partitions(struct mtd_info *master,
- struct mtd_partition **pparts,
- unsigned long fis_origin)
- {
-@@ -161,6 +161,14 @@
- goto out;
- }
-
-+ if (!fis_origin) {
-+ for (i = 0; i < numslots; i++) {
-+ if (!strncmp(buf[i].name, "RedBoot", 8)) {
-+ fis_origin = (buf[i].flash_base & (master->size << 1) - 1);
-+ }
-+ }
-+ }
-+
- for (i = 0; i < numslots; i++) {
- struct fis_list *new_fl, **prev;
-
-@@ -183,9 +191,8 @@
- new_fl->img = &buf[i];
- if (fis_origin) {
- buf[i].flash_base -= fis_origin;
-- } else {
-- buf[i].flash_base &= master->size-1;
- }
-+ buf[i].flash_base &= (master->size << 1) - 1;
-
- /* I'm sure the JFFS2 code has done me permanent damage.
- * I now think the following is _normal_
+++ /dev/null
-From 40dd38388c3d1c87efe254cee533fc5db5ffc4ed Mon Sep 17 00:00:00 2001
-From: Axel Gembe <ago@bastart.eu.org>
-Date: Wed, 14 May 2008 12:43:34 +0200
-Subject: [PATCH] bcm963xx: add missing trailing zero to load address
-
-The load address for BCM963xx is 0x80010000, not 0xf8001000 as in the current
-sources. I think this is just a typo, so this patch fixes it (tested on 96345).
-
-Signed-off-by: Axel Gembe <ago@bastart.eu.org>
----
- arch/mips/Makefile | 2 +-
- 1 files changed, 1 insertions(+), 1 deletions(-)
-
---- a/arch/mips/Makefile
-+++ b/arch/mips/Makefile
-@@ -562,7 +562,7 @@
-
- core-$(CONFIG_BCM963XX) += arch/mips/bcm963xx/
- cflags-$(CONFIG_BCM963XX) += -Iinclude/asm-mips/mach-bcm963xx
--load-$(CONFIG_BCM963XX) := 0xffffffff8001000
-+load-$(CONFIG_BCM963XX) := 0xffffffff80010000
-
- #
- # SNI RM
+++ /dev/null
-From 9a70f2dcb24a5aab29386373c86ba035acba4891 Mon Sep 17 00:00:00 2001
-From: Axel Gembe <ago@bastart.eu.org>
-Date: Sun, 18 May 2008 12:07:21 +0200
-Subject: [PATCH] bcm963xx: rewrite irq handling code
-
-This patch adds interrupt handling as on AR7. The old code was very messy and
-didn't work too well.
-
-Signed-off-by: Axel Gembe <ago@bastart.eu.org>
----
- arch/mips/bcm963xx/irq.c | 308 ++++++++++-------------------
- drivers/serial/bcm63xx_cons.c | 13 +-
- include/asm-mips/mach-bcm963xx/bcm_intr.h | 18 +--
- 3 files changed, 119 insertions(+), 220 deletions(-)
-
---- a/arch/mips/bcm963xx/irq.c
-+++ b/arch/mips/bcm963xx/irq.c
-@@ -1,259 +1,159 @@
- /*
--<:copyright-gpl
-- Copyright 2002 Broadcom Corp. All Rights Reserved.
--
-- This program is free software; you can distribute it and/or modify it
-- under the terms of the GNU General Public License (Version 2) as
-- published by the Free Software Foundation.
--
-- This program is distributed in the hope it will be useful, but WITHOUT
-- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-- for more details.
--
-- You should have received a copy of the GNU General Public License along
-- with this program; if not, write to the Free Software Foundation, Inc.,
-- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
--:>
--*/
--/*
-- * Interrupt control functions for Broadcom 963xx MIPS boards
-+ * Copyright (C) 2006,2007 Felix Fietkau <nbd@openwrt.org>
-+ * Copyright (C) 2006,2007 Eugene Konev <ejka@openwrt.org>
-+ * Copyright (C) 2008 Axel Gembe <ago@bastart.eu.org>
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
--#include <asm/atomic.h>
--
--#include <linux/delay.h>
--#include <linux/init.h>
--#include <linux/ioport.h>
--#include <linux/irq.h>
- #include <linux/interrupt.h>
--#include <linux/kernel.h>
--#include <linux/slab.h>
--#include <linux/module.h>
-+#include <linux/io.h>
-
--#include <asm/irq.h>
-+#include <asm/irq_cpu.h>
- #include <asm/mipsregs.h>
--#include <asm/addrspace.h>
--#include <asm/signal.h>
-+
- #include <6348_map_part.h>
- #include <6348_intr.h>
- #include <bcm_map_part.h>
- #include <bcm_intr.h>
-
--static void irq_dispatch_int(void)
--{
-- unsigned int pendingIrqs;
-- static unsigned int irqBit;
-- static unsigned int isrNumber = 31;
--
-- pendingIrqs = PERF->IrqStatus & PERF->IrqMask;
-- if (!pendingIrqs) {
-- return;
-- }
-+static int bcm963xx_irq_base;
-
-- while (1) {
-- irqBit <<= 1;
-- isrNumber++;
-- if (isrNumber == 32) {
-- isrNumber = 0;
-- irqBit = 0x1;
-- }
-- if (pendingIrqs & irqBit) {
-- PERF->IrqMask &= ~irqBit; // mask
-- do_IRQ(isrNumber + INTERNAL_ISR_TABLE_OFFSET);
-- break;
-- }
-- }
-+void bcm963xx_unmask_irq(unsigned int irq)
-+{
-+ PERF->IrqMask |= (1 << (irq - bcm963xx_irq_base));
- }
-
--static void irq_dispatch_ext(uint32 irq)
-+void bcm963xx_mask_irq(unsigned int irq)
- {
-- if (!(PERF->ExtIrqCfg & (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT)))) {
-- printk("**** Ext IRQ mask. Should not dispatch ****\n");
-- }
-- /* disable and clear interrupt in the controller */
-- PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_CLEAR_SHFT));
-- PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT));
-- do_IRQ(irq);
-+ PERF->IrqMask &= ~(1 << (irq - bcm963xx_irq_base));
- }
-
--
--//extern void brcm_timer_interrupt(struct pt_regs *regs);
--
--asmlinkage void plat_irq_dispatch(void)
-+void bcm963xx_ack_irq(unsigned int irq)
- {
-- unsigned long cause;
--
-- cause = read_c0_status() & read_c0_cause() & ST0_IM;
-- if (cause & CAUSEF_IP7)
-- do_IRQ(7);
-- else if (cause & CAUSEF_IP2)
-- irq_dispatch_int();
-- else if (cause & CAUSEF_IP3)
-- irq_dispatch_ext(INTERRUPT_ID_EXTERNAL_0);
-- else if (cause & CAUSEF_IP4)
-- irq_dispatch_ext(INTERRUPT_ID_EXTERNAL_1);
-- else if (cause & CAUSEF_IP5)
-- irq_dispatch_ext(INTERRUPT_ID_EXTERNAL_2);
-- else if (cause & CAUSEF_IP6) {
-- irq_dispatch_ext(INTERRUPT_ID_EXTERNAL_3);
-- local_irq_disable();
-- }
-+ PERF->IrqStatus &= ~(1 << (irq - bcm963xx_irq_base));
- }
-
--
--void enable_brcm_irq(unsigned int irq)
-+void bcm963xx_unmask_ext_irq(unsigned int irq)
- {
-- unsigned long flags;
--
-- local_irq_save(flags);
-- if( irq >= INTERNAL_ISR_TABLE_OFFSET ) {
-- PERF->IrqMask |= (1 << (irq - INTERNAL_ISR_TABLE_OFFSET));
-- }
-- else if (irq >= INTERRUPT_ID_EXTERNAL_0 && irq <= INTERRUPT_ID_EXTERNAL_3) {
-- /* enable and clear interrupt in the controller */
-- PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_CLEAR_SHFT));
- PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT));
-- }
-- local_irq_restore(flags);
- }
-
--void disable_brcm_irq(unsigned int irq)
-+void bcm963xx_mask_ext_irq(unsigned int irq)
- {
-- unsigned long flags;
--
-- local_irq_save(flags);
-- if( irq >= INTERNAL_ISR_TABLE_OFFSET ) {
-- PERF->IrqMask &= ~(1 << (irq - INTERNAL_ISR_TABLE_OFFSET));
-- }
-- else if (irq >= INTERRUPT_ID_EXTERNAL_0 && irq <= INTERRUPT_ID_EXTERNAL_3) {
-- /* disable interrupt in the controller */
- PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT));
-- }
-- local_irq_restore(flags);
- }
-
--void ack_brcm_irq(unsigned int irq)
-+void bcm963xx_ack_ext_irq(unsigned int irq)
- {
-- /* Already done in brcm_irq_dispatch */
-+ PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_CLEAR_SHFT));
- }
-
--unsigned int startup_brcm_irq(unsigned int irq)
-+static void bcm963xx_dispatch_ext_irq(unsigned int irq)
- {
-- enable_brcm_irq(irq);
--
-- return 0; /* never anything pending */
-+ bcm963xx_ack_ext_irq(irq);
-+ bcm963xx_mask_ext_irq(irq);
-+ do_IRQ(irq);
- }
-
--unsigned int startup_brcm_none(unsigned int irq)
-+static void bcm963xx_cascade(void)
- {
-- return 0;
--}
-+ uint32_t pending, bit, irq;
-
--void end_brcm_irq(unsigned int irq)
--{
-- if (!(irq_desc[irq].status & (IRQ_DISABLED|IRQ_INPROGRESS)))
-- enable_brcm_irq(irq);
--}
-+ if (!(pending = PERF->IrqStatus & PERF->IrqMask))
-+ return;
-
--void end_brcm_none(unsigned int irq)
--{
--}
-+ for (irq = 0, bit = 1; irq < 32; irq++, bit <<= 1) {
-+ if (pending & bit) {
-+ bcm963xx_ack_irq(irq + bcm963xx_irq_base);
-+ bcm963xx_mask_irq(irq + bcm963xx_irq_base);
-+ do_IRQ(irq + bcm963xx_irq_base);
-+ return;
-+ }
-+ }
-+
-+ spurious_interrupt();
-+}
-+
-+static struct irq_chip bcm963xx_irq_type = {
-+ .name = "bcm963xx",
-+ .unmask = bcm963xx_unmask_irq,
-+ .mask = bcm963xx_mask_irq,
-+ .ack = bcm963xx_ack_irq
-+};
-
--static struct hw_interrupt_type brcm_irq_type = {
-- .typename = "MIPS",
-- .startup = startup_brcm_irq,
-- .shutdown = disable_brcm_irq,
-- .enable = enable_brcm_irq,
-- .disable = disable_brcm_irq,
-- .ack = ack_brcm_irq,
-- .end = end_brcm_irq,
-- .set_affinity = NULL
-+static struct irq_chip bcm963xx_ext_irq_type = {
-+ .name = "bcm963xx_ext",
-+ .unmask = bcm963xx_unmask_ext_irq,
-+ .mask = bcm963xx_mask_ext_irq,
-+ .ack = bcm963xx_ack_ext_irq,
- };
-
--static struct hw_interrupt_type brcm_irq_no_end_type = {
-- .typename = "MIPS",
-- .startup = startup_brcm_none,
-- .shutdown = disable_brcm_irq,
-- .enable = enable_brcm_irq,
-- .disable = disable_brcm_irq,
-- .ack = ack_brcm_irq,
-- .end = end_brcm_none,
-- .set_affinity = NULL
-+static struct irqaction bcm963xx_cascade_action = {
-+ .handler = no_action,
-+ .name = "BCM963xx cascade interrupt"
- };
-
--void __init arch_init_irq(void)
-+static void __init bcm963xx_irq_init(int base)
- {
- int i;
-
-- clear_c0_status(ST0_BEV);
-- change_c0_status(ST0_IM, (IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3 | IE_IRQ4));
-+ bcm963xx_irq_base = base;
-
-- for (i = 0; i < NR_IRQS; i++) {
-- irq_desc[i].status = IRQ_DISABLED;
-- irq_desc[i].action = 0;
-- irq_desc[i].depth = 1;
-- irq_desc[i].chip = &brcm_irq_type;
-- }
-+ /* External IRQs */
-+ set_irq_chip_and_handler(INTERRUPT_ID_EXTERNAL_0, &bcm963xx_ext_irq_type,
-+ handle_level_irq);
-+ set_irq_chip_and_handler(INTERRUPT_ID_EXTERNAL_1, &bcm963xx_ext_irq_type,
-+ handle_level_irq);
-+ set_irq_chip_and_handler(INTERRUPT_ID_EXTERNAL_2, &bcm963xx_ext_irq_type,
-+ handle_level_irq);
-+ set_irq_chip_and_handler(INTERRUPT_ID_EXTERNAL_3, &bcm963xx_ext_irq_type,
-+ handle_level_irq);
-+
-+ for (i = 0; i < 32; i++) {
-+ set_irq_chip_and_handler(base + i, &bcm963xx_irq_type,
-+ handle_level_irq);
-+ }
-+
-+ setup_irq(2, &bcm963xx_cascade_action);
-+ setup_irq(bcm963xx_irq_base, &bcm963xx_cascade_action);
-+ set_c0_status(IE_IRQ0);
- }
-
--int request_external_irq(unsigned int irq,
-- FN_HANDLER handler,
-- unsigned long irqflags,
-- const char * devname,
-- void *dev_id)
-+asmlinkage void plat_irq_dispatch(void)
- {
-- unsigned long flags;
--
-- local_irq_save(flags);
-+ unsigned int pending = read_c0_status() & read_c0_cause() & ST0_IM;
-
-- PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_CLEAR_SHFT)); // Clear
-- PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_MASK_SHFT)); // Mask
-- PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_INSENS_SHFT)); // Edge insesnsitive
-- PERF->ExtIrqCfg |= (1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_LEVEL_SHFT)); // Level triggered
-- PERF->ExtIrqCfg &= ~(1 << (irq - INTERRUPT_ID_EXTERNAL_0 + EI_SENSE_SHFT)); // Low level
--
-- local_irq_restore(flags);
--
-- return( request_irq(irq, handler, irqflags, devname, dev_id) );
-+ if (pending & STATUSF_IP7) /* cpu timer */
-+ do_IRQ(7);
-+ else if (pending & STATUSF_IP2) /* internal interrupt cascade */
-+ bcm963xx_cascade();
-+ else if (pending & STATUSF_IP3)
-+ bcm963xx_dispatch_ext_irq(INTERRUPT_ID_EXTERNAL_0);
-+ else if (pending & STATUSF_IP4)
-+ bcm963xx_dispatch_ext_irq(INTERRUPT_ID_EXTERNAL_1);
-+ else if (pending & STATUSF_IP5)
-+ bcm963xx_dispatch_ext_irq(INTERRUPT_ID_EXTERNAL_2);
-+ else if (pending & STATUSF_IP6)
-+ bcm963xx_dispatch_ext_irq(INTERRUPT_ID_EXTERNAL_3);
-+ else
-+ spurious_interrupt();
- }
-
--/* VxWorks compatibility function(s). */
--
--unsigned int BcmHalMapInterrupt(FN_HANDLER pfunc, unsigned int param,
-- unsigned int interruptId)
-+void __init arch_init_irq(void)
- {
-- int nRet = -1;
-- char *devname;
--
-- devname = kmalloc(16, GFP_KERNEL);
-- if (devname)
-- sprintf( devname, "brcm_%d", interruptId );
--
-- /* Set the IRQ description to not automatically enable the interrupt at
-- * the end of an ISR. The driver that handles the interrupt must
-- * explicitly call BcmHalInterruptEnable or enable_brcm_irq. This behavior
-- * is consistent with interrupt handling on VxWorks.
-- */
-- irq_desc[interruptId].chip = &brcm_irq_no_end_type;
--
-- if( interruptId >= INTERNAL_ISR_TABLE_OFFSET )
-- {
-- printk("BcmHalMapInterrupt : internal IRQ\n");
-- nRet = request_irq( interruptId, pfunc, IRQF_DISABLED, devname, (void *) param );
-- }
-- else if (interruptId >= INTERRUPT_ID_EXTERNAL_0 && interruptId <= INTERRUPT_ID_EXTERNAL_3)
-- {
-- printk("BcmHalMapInterrupt : external IRQ\n");
-- nRet = request_external_irq( interruptId, pfunc, IRQF_DISABLED, devname, (void *) param );
-- }
--
-- return( nRet );
-+ mips_cpu_irq_init();
-+ bcm963xx_irq_init(INTERNAL_ISR_TABLE_OFFSET);
- }
--
--
--EXPORT_SYMBOL(enable_brcm_irq);
--EXPORT_SYMBOL(disable_brcm_irq);
--EXPORT_SYMBOL(request_external_irq);
--EXPORT_SYMBOL(BcmHalMapInterrupt);
--
---- a/drivers/serial/bcm63xx_cons.c
-+++ b/drivers/serial/bcm63xx_cons.c
-@@ -267,7 +267,7 @@
- }
-
- // Clear the interrupt
-- enable_brcm_irq(INTERRUPT_ID_UART);
-+// bcm963xx_unmask_irq(INTERRUPT_ID_UART);
- #if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,0)
- return IRQ_HANDLED;
- #endif
-@@ -880,7 +880,7 @@
- info->count++;
- tty->driver_data = info;
- info->tty = tty;
-- enable_brcm_irq(INTERRUPT_ID_UART);
-+ bcm963xx_unmask_irq(INTERRUPT_ID_UART);
-
- // Start up serial port
- retval = startup(info);
-@@ -927,7 +927,7 @@
- -------------------------------------------------------------------------- */
- static int __init bcm63xx_serialinit(void)
- {
-- int i, flags;
-+ int i, flags, res;
- struct bcm_serial *info;
-
- // Print the driver version information
-@@ -981,7 +981,12 @@
- */
- if (!info->port)
- return 0;
-- BcmHalMapInterrupt(bcm_interrupt, 0, INTERRUPT_ID_UART);
-+
-+ res = request_irq(INTERRUPT_ID_UART, bcm_interrupt, 0, "bcm-uart", NULL);
-+ if (res) {
-+ spin_unlock_irqrestore(&bcm963xx_serial_lock, flags);
-+ return res;
-+ }
- }
-
- /* order matters here... the trick is that flags
---- a/include/asm-mips/mach-bcm963xx/bcm_intr.h
-+++ b/include/asm-mips/mach-bcm963xx/bcm_intr.h
-@@ -39,18 +39,12 @@
- typedef int (*FN_HANDLER) (int, void *);
-
- /* prototypes */
--extern void enable_brcm_irq(unsigned int irq);
--extern void disable_brcm_irq(unsigned int irq);
--extern int request_external_irq(unsigned int irq,
-- FN_HANDLER handler, unsigned long irqflags,
-- const char * devname, void *dev_id);
--extern unsigned int BcmHalMapInterrupt(FN_HANDLER isr, unsigned int param,
-- unsigned int interruptId);
--extern void dump_intr_regs(void);
--
--/* compatibility definitions */
--#define BcmHalInterruptEnable(irq) enable_brcm_irq( irq )
--#define BcmHalInterruptDisable(irq) disable_brcm_irq( irq )
-+extern void bcm963xx_unmask_irq(unsigned int irq);
-+extern void bcm963xx_mask_irq(unsigned int irq);
-+extern void bcm963xx_ack_irq(unsigned int irq);
-+extern void bcm963xx_unmask_ext_irq(unsigned int irq);
-+extern void bcm963xx_mask_ext_irq(unsigned int irq);
-+extern void bcm963xx_ack_ext_irq(unsigned int irq);
-
- #ifdef __cplusplus
- }
+++ /dev/null
-From 7bc3950017d2c54883591367723b7fd84cc65d6f Mon Sep 17 00:00:00 2001
-From: Axel Gembe <ago@bastart.eu.org>
-Date: Sun, 18 May 2008 12:09:14 +0200
-Subject: [PATCH] bcm963xx: fix uart isr
-
-The ISR ended up in an endless loop because the TX ISR never got used or masked.
-This patch basically makes the TX ISR mask the the TX interrupt when it
-encounters it, because it doesn't even use the TX interrupt.
-
-Signed-off-by: Axel Gembe <ago@bastart.eu.org>
----
- drivers/serial/bcm63xx_cons.c | 6 ++++++
- 1 files changed, 6 insertions(+), 0 deletions(-)
-
---- a/drivers/serial/bcm63xx_cons.c
-+++ b/drivers/serial/bcm63xx_cons.c
-@@ -258,8 +258,14 @@
- while (intStat) {
- if (intStat & RXINT)
- receive_chars(info);
-+
-+#if 0 /* This code is total bullshit, TXINT doesn't get masked anywhere, so this will give an endless loop */
-+
- else if (intStat & TXINT)
- info->port->intStatus = TXINT;
-+
-+#endif /* 0 */
-+
- else /* don't know what it was, so let's mask it */
- info->port->intMask &= ~intStat;
-
+++ /dev/null
-From e3abd028e7631ee952fe73d8f9ee97bc615526a8 Mon Sep 17 00:00:00 2001
-From: Axel Gembe <ago@bastart.eu.org>
-Date: Sat, 17 May 2008 16:07:46 +0200
-Subject: [PATCH] bcm963xx: remove unused int-handler.S
-
-The code is not used anymore.
-
-Signed-off-by: Axel Gembe <ago@bastart.eu.org>
----
- arch/mips/bcm963xx/Makefile | 2 +-
- arch/mips/bcm963xx/int-handler.S | 59 --------------------------------------
- 2 files changed, 1 insertions(+), 60 deletions(-)
- delete mode 100644 arch/mips/bcm963xx/int-handler.S
-
---- a/arch/mips/bcm963xx/Makefile
-+++ b/arch/mips/bcm963xx/Makefile
-@@ -3,7 +3,7 @@
- #
- # Copyright (C) 2004 Broadcom Corporation
- #
--obj-y := irq.o prom.o setup.o time.o ser_init.o int-handler.o info.o wdt.o
-+obj-y := irq.o prom.o setup.o time.o ser_init.o info.o wdt.o
-
- SRCBASE := $(TOPDIR)
- EXTRA_CFLAGS += -I$(SRCBASE)/include
---- a/arch/mips/bcm963xx/int-handler.S
-+++ /dev/null
-@@ -1,59 +0,0 @@
--/*
--<:copyright-gpl
-- Copyright 2002 Broadcom Corp. All Rights Reserved.
--
-- This program is free software; you can distribute it and/or modify it
-- under the terms of the GNU General Public License (Version 2) as
-- published by the Free Software Foundation.
--
-- This program is distributed in the hope it will be useful, but WITHOUT
-- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
-- for more details.
--
-- You should have received a copy of the GNU General Public License along
-- with this program; if not, write to the Free Software Foundation, Inc.,
-- 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
--:>
--*/
--/*
-- * Generic interrupt handler for Broadcom MIPS boards
-- */
--
--#include <linux/autoconf.h>
--
--#include <asm/asm.h>
--#include <asm/mipsregs.h>
--#include <asm/regdef.h>
--#include <asm/stackframe.h>
--
--/*
-- * MIPS IRQ Source
-- * -------- ------
-- * 0 Software (ignored)
-- * 1 Software (ignored)
-- * 2 Combined hardware interrupt (hw0)
-- * 3 Hardware
-- * 4 Hardware
-- * 5 Hardware
-- * 6 Hardware
-- * 7 R4k timer
-- */
--
-- .text
-- .set noreorder
-- .set noat
-- .align 5
-- NESTED(brcmIRQ, PT_SIZE, sp)
-- SAVE_ALL
-- CLI
-- .set noreorder
-- .set at
--
-- jal plat_irq_dispatch
-- move a0, sp
--
-- j ret_from_irq
-- nop
--
-- END(brcmIRQ)
+++ /dev/null
-From 42ecc15386869684cf29881a3a6941bafaa3bf69 Mon Sep 17 00:00:00 2001
-From: Axel Gembe <ago@bastart.eu.org>
-Date: Wed, 14 May 2008 00:25:28 +0200
-Subject: [PATCH] bcm963xx: remove obsolete timer code
-
-This removes some code that has been deprecated in kernels >= 2.6.24.
-
-Signed-off-by: Axel Gembe <ago@bastart.eu.org>
----
- arch/mips/bcm963xx/setup.c | 2 --
- arch/mips/bcm963xx/time.c | 29 -----------------------------
- 2 files changed, 0 insertions(+), 31 deletions(-)
-
---- a/arch/mips/bcm963xx/setup.c
-+++ b/arch/mips/bcm963xx/setup.c
-@@ -465,8 +465,6 @@
- _machine_halt = brcm_machine_halt;
- pm_power_off = brcm_machine_halt;
-
-- //board_time_init = brcm_time_init;
--
- /* mpi initialization */
- mpi_init();
- }
---- a/arch/mips/bcm963xx/time.c
-+++ b/arch/mips/bcm963xx/time.c
-@@ -71,26 +71,6 @@
- return (mips_hpt_frequency / HZ);
- }
-
--
--/*
-- * There are a lot of conceptually broken versions of the MIPS timer interrupt
-- * handler floating around. This one is rather different, but the algorithm
-- * is provably more robust.
-- */
--#if 0
--irqreturn_t brcm_timer_interrupt(struct pt_regs *regs)
--{
-- int irq = MIPS_TIMER_INT;
--
-- irq_enter();
-- kstat_this_cpu.irqs[irq]++;
--
-- timer_interrupt(irq, regs);
-- irq_exit();
-- return IRQ_HANDLED;
--}
--#endif
--
- void __init plat_time_init(void)
- {
- unsigned int est_freq, flags;
-@@ -107,12 +87,3 @@
- (est_freq % 1000000) * 100 / 1000000);
- local_irq_restore(flags);
- }
--
--#if 0
--void __init plat_timer_setup(struct irqaction *irq)
--{
-- r4k_cur = (read_c0_count() + r4k_offset);
-- write_c0_compare(r4k_cur);
-- set_c0_status(IE_IRQ5);
--}
--#endif
+++ /dev/null
-From 7d6656dc127b54e53e507e8f264bb7e14e620cad Mon Sep 17 00:00:00 2001
-From: Axel Gembe <ago@bastart.eu.org>
-Date: Sat, 17 May 2008 15:02:39 +0200
-Subject: [PATCH] bcm963xx: add new timer code
-
-This basically selects the new generic MIPS timer code for BCM963xx and
-simplifies the timer setup code.
-
-Signed-off-by: Axel Gembe <ago@bastart.eu.org>
----
- arch/mips/Kconfig | 2 +
- arch/mips/bcm963xx/time.c | 64 ++++++++++++++++++++------------------------
- 2 files changed, 31 insertions(+), 35 deletions(-)
-
---- a/arch/mips/Kconfig
-+++ b/arch/mips/Kconfig
-@@ -67,6 +67,8 @@
- select HW_HAS_PCI
- select DMA_NONCOHERENT
- select IRQ_CPU
-+ select CEVT_R4K
-+ select CSRC_R4K
- help
- This is a fmaily of boards based on the Broadcom MIPS32
-
---- a/arch/mips/bcm963xx/time.c
-+++ b/arch/mips/bcm963xx/time.c
-@@ -1,6 +1,7 @@
- /*
- <:copyright-gpl
- Copyright 2004 Broadcom Corp. All Rights Reserved.
-+ Copyright (C) 2008 Axel Gembe <ago@bastart.eu.org>
-
- This program is free software; you can distribute it and/or modify it
- under the terms of the GNU General Public License (Version 2) as
-@@ -40,50 +41,43 @@
- #include <bcm_map_part.h>
- #include <bcm_intr.h>
-
--static unsigned long r4k_offset; /* Amount to increment compare reg each time */
--static unsigned long r4k_cur; /* What counter should be at next timer irq */
--
--/* *********************************************************************
-- * calculateCpuSpeed()
-- * Calculate the BCM6348 CPU speed by reading the PLL strap register
-- * and applying the following formula:
-- * cpu_clk = (.25 * 64MHz freq) * (N1 + 1) * (N2 + 2) / (M1_CPU + 1)
-- * Input parameters:
-- * none
-- * Return value:
-- * none
-- ********************************************************************* */
--
-+/*
-+ * calculateCpuSpeed()
-+ *
-+ * Calculate the BCM6348 CPU speed by reading the PLL strap register and applying
-+ * the following formula:
-+ *
-+ * cpu_clk = (.25 * 64MHz freq) * (N1 + 1) * (N2 + 2) / (M1_CPU + 1)
-+ */
- static inline unsigned long __init calculateCpuSpeed(void)
- {
-- u32 pllStrap = PERF->PllStrap;
-- int n1 = (pllStrap & PLL_N1_MASK) >> PLL_N1_SHFT;
-- int n2 = (pllStrap & PLL_N2_MASK) >> PLL_N2_SHFT;
-- int m1cpu = (pllStrap & PLL_M1_CPU_MASK) >> PLL_M1_CPU_SHFT;
-+ u32 pllStrap;
-+ int n1, n2, m1cpu;
-+
-+ pllStrap = PERF->PllStrap;
-+ n1 = (pllStrap & PLL_N1_MASK) >> PLL_N1_SHFT;
-+ n2 = (pllStrap & PLL_N2_MASK) >> PLL_N2_SHFT;
-+ m1cpu = (pllStrap & PLL_M1_CPU_MASK) >> PLL_M1_CPU_SHFT;
-
- return (16 * (n1 + 1) * (n2 + 2) / (m1cpu + 1)) * 1000000;
- }
-
-
--static inline unsigned long __init cal_r4koff(void)
--{
-- mips_hpt_frequency = calculateCpuSpeed() / 2;
-- return (mips_hpt_frequency / HZ);
--}
--
- void __init plat_time_init(void)
- {
-- unsigned int est_freq, flags;
-- local_irq_save(flags);
-+ unsigned long cpu_clock;
-+
-+ cpu_clock = calculateCpuSpeed();
-+
-+ printk("CPU frequency %lu.%02lu MHz\n", cpu_clock / 1000000,
-+ (cpu_clock % 1000000) * 100 / 1000000);
-+
-+ mips_hpt_frequency = cpu_clock / 2;
-
-- printk("calculating r4koff... ");
-- r4k_offset = cal_r4koff();
-- printk("%08lx(%d)\n", r4k_offset, (int)r4k_offset);
--
-- est_freq = 2 * r4k_offset * HZ;
-- est_freq += 5000; /* round */
-- est_freq -= est_freq % 10000;
-- printk("CPU frequency %d.%02d MHz\n", est_freq / 1000000,
-- (est_freq % 1000000) * 100 / 1000000);
-- local_irq_restore(flags);
-+ /*
-+ * Use deterministic values for initial counter interrupt
-+ * so that calibrate delay avoids encountering a counter wrap.
-+ */
-+ write_c0_count(0);
-+ write_c0_compare(0xffff);
- }
+++ /dev/null
-From f1a605c36cf1659f5f486ae4135de1e285fdf86c Mon Sep 17 00:00:00 2001
-From: Axel Gembe <ago@bastart.eu.org>
-Date: Sat, 17 May 2008 16:17:22 +0200
-Subject: [PATCH] bcm963xx: fix cfe detection
-
-The CFE detection failed to account for zero termination.
-
-Signed-off-by: Axel Gembe <ago@bastart.eu.org>
----
- drivers/mtd/maps/bcm963xx-flash.c | 11 ++++++-----
- 1 files changed, 6 insertions(+), 5 deletions(-)
-
---- a/drivers/mtd/maps/bcm963xx-flash.c
-+++ b/drivers/mtd/maps/bcm963xx-flash.c
-@@ -1,8 +1,7 @@
- /*
-- * $Id$
- * Copyright (C) 2006 Florian Fainelli <florian@openwrt.org>
-- * Mike Albon <malbon@openwrt.org>
-- * Copyright (C) $Date$ $Author$
-+ * Mike Albon <malbon@openwrt.org>
-+ * Copyright (C) 2008 Axel Gembe <ago@bastart.eu.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
-@@ -184,11 +183,13 @@
- static int bcm963xx_detect_cfe(struct mtd_info *master)
- {
- int idoffset = 0x4e0;
-- static char idstring[8] = "CFE1CFE1";
-- char buf[8];
-+ static char idstring[9] = "CFE1CFE1";
-+ char buf[9];
- int ret;
- size_t retlen;
-
-+ memset(buf, 0, sizeof(buf));
-+
- ret = master->read(master, idoffset, 8, &retlen, (void *)buf);
- printk("bcm963xx: Read Signature value of %s\n", buf);
- return strcmp(idstring,buf);
+++ /dev/null
-From d1259cf42ce84246c695f06b44d58e3aca0a480b Mon Sep 17 00:00:00 2001
-From: Axel Gembe <ago@bastart.eu.org>
-Date: Sat, 17 May 2008 14:59:35 +0200
-Subject: [PATCH] bcm96345: correct some 6345 specific stuff
-
-This fixes some problems with the 6345 support and adds a macro for CPU
-identification that is easier on the eyes. The first thing it does is to not
-initialize MPI on the 6345 as it does not have PCI. The second thing it does is
-to use a static value for the CPU frequency of the 6345 chip to provide an
-accurate timer.
-
-Signed-off-by: Axel Gembe <ago@bastart.eu.org>
----
- arch/mips/bcm963xx/setup.c | 8 ++++++--
- arch/mips/bcm963xx/time.c | 5 ++++-
- arch/mips/pci/pci-bcm96348.c | 21 +++++++++++++--------
- include/asm-mips/mach-bcm963xx/board.h | 2 ++
- 4 files changed, 25 insertions(+), 11 deletions(-)
-
---- a/arch/mips/bcm963xx/setup.c
-+++ b/arch/mips/bcm963xx/setup.c
-@@ -43,6 +43,7 @@
- #include <asm/bootinfo.h>
- #include <asm/cpu.h>
- #include <asm/mach-bcm963xx/bootloaders.h>
-+#include <asm/mach-bcm963xx/board.h>
-
- extern void brcm_time_init(void);
- extern int boot_loader_type;
-@@ -465,6 +466,9 @@
- _machine_halt = brcm_machine_halt;
- pm_power_off = brcm_machine_halt;
-
-- /* mpi initialization */
-- mpi_init();
-+ /* BCM96345 has no MPI */
-+ if (!ISBCM(0x6345)) {
-+ /* mpi initialization */
-+ mpi_init();
-+ }
- }
---- a/arch/mips/bcm963xx/time.c
-+++ b/arch/mips/bcm963xx/time.c
-@@ -40,6 +40,8 @@
- #include <6348_intr.h>
- #include <bcm_map_part.h>
- #include <bcm_intr.h>
-+#include <asm/mach-bcm963xx/board.h>
-+
-
- /*
- * calculateCpuSpeed()
-@@ -63,11 +65,12 @@
- }
-
-
-+#define BCM96345_CPU_CLOCK 140000000
- void __init plat_time_init(void)
- {
- unsigned long cpu_clock;
-
-- cpu_clock = calculateCpuSpeed();
-+ cpu_clock = ISBCM(0x6345) ? BCM96345_CPU_CLOCK : calculateCpuSpeed();
-
- printk("CPU frequency %lu.%02lu MHz\n", cpu_clock / 1000000,
- (cpu_clock % 1000000) * 100 / 1000000);
---- a/arch/mips/pci/pci-bcm96348.c
-+++ b/arch/mips/pci/pci-bcm96348.c
-@@ -21,6 +21,8 @@
- #include <linux/kernel.h>
- #include <linux/init.h>
-
-+#include <asm/mach-bcm963xx/6348_map_part.h>
-+#include <asm/mach-bcm963xx/board.h>
- #include <bcmpci.h>
-
- static struct resource bcm_pci_io_resource = {
-@@ -47,16 +49,19 @@
-
- static __init int bcm96348_pci_init(void)
- {
-- /* Avoid ISA compat ranges. */
-- PCIBIOS_MIN_IO = 0x00000000;
-- PCIBIOS_MIN_MEM = 0x00000000;
--
-- /* Set I/O resource limits. */
-- ioport_resource.end = 0x1fffffff;
-- iomem_resource.end = 0xffffffff;
-+ if (!ISBCM(0x6345)) {
-+ /* Avoid ISA compat ranges. */
-+ PCIBIOS_MIN_IO = 0x00000000;
-+ PCIBIOS_MIN_MEM = 0x00000000;
-+
-+ /* Set I/O resource limits. */
-+ ioport_resource.end = 0x1fffffff;
-+ iomem_resource.end = 0xffffffff;
-
-- register_pci_controller(&bcm96348_controller);
-- return 0;
-+ register_pci_controller(&bcm96348_controller);
-+ }
-+
-+ return 0;
- }
-
- arch_initcall(bcm96348_pci_init);
---- a/include/asm-mips/mach-bcm963xx/board.h
-+++ b/include/asm-mips/mach-bcm963xx/board.h
-@@ -369,5 +369,7 @@
-
- extern int boot_loader_type;
-
-+#define ISBCM(x) (((PERF->RevID & 0xFFFF0000) >> 16) == x)
-+
- #endif /* _BOARD_H */
-
+++ /dev/null
-Index: linux-2.6.24.7/arch/mips/Kconfig
-===================================================================
---- linux-2.6.24.7.orig/arch/mips/Kconfig
-+++ linux-2.6.24.7/arch/mips/Kconfig
-@@ -67,6 +67,17 @@ config BCM47XX
- help
- Support for BCM47XX based boards
-
-+config BCM963XX
-+ bool "Support for Broadcom BCM963xx SoC"
-+ select SYS_SUPPORTS_32BIT_KERNEL
-+ select SYS_SUPPORTS_BIG_ENDIAN
-+ select SYS_HAS_CPU_MIPS32_R1
-+ select HW_HAS_PCI
-+ select DMA_NONCOHERENT
-+ select IRQ_CPU
-+ help
-+ This is a fmaily of boards based on the Broadcom MIPS32
-+
- config MIPS_COBALT
- bool "Cobalt Server"
- select CEVT_R4K
-Index: linux-2.6.24.7/arch/mips/kernel/cpu-probe.c
-===================================================================
---- linux-2.6.24.7.orig/arch/mips/kernel/cpu-probe.c
-+++ linux-2.6.24.7/arch/mips/kernel/cpu-probe.c
-@@ -796,6 +796,18 @@ static inline void cpu_probe_broadcom(st
- case PRID_IMP_BCM4710:
- c->cputype = CPU_BCM4710;
- break;
-+// case PRID_IMP_BCM6338:
-+// c->cputype = CPU_BCM6338;
-+// break;
-+ case PRID_IMP_BCM6345:
-+ c->cputype = CPU_BCM6345;
-+ break;
-+ case PRID_IMP_BCM6348:
-+ c->cputype = CPU_BCM6348;
-+ break;
-+ case PRID_IMP_BCM6358:
-+ c->cputype = CPU_BCM6358;
-+ break;
- default:
- c->cputype = CPU_UNKNOWN;
- break;
-@@ -878,6 +890,10 @@ static __init const char *cpu_to_name(st
- case CPU_SR71000: name = "Sandcraft SR71000"; break;
- case CPU_BCM3302: name = "Broadcom BCM3302"; break;
- case CPU_BCM4710: name = "Broadcom BCM4710"; break;
-+ case CPU_BCM6338: name = "Broadcom BCM6338"; break;
-+ case CPU_BCM6345: name = "Broadcom BCM6345"; break;
-+ case CPU_BCM6348: name = "Broadcom BCM6348"; break;
-+ case CPU_BCM6358: name = "Broadcom BCM6358"; break;
- case CPU_PR4450: name = "Philips PR4450"; break;
- case CPU_LOONGSON2: name = "ICT Loongson-2"; break;
- default:
-Index: linux-2.6.24.7/arch/mips/Makefile
-===================================================================
---- linux-2.6.24.7.orig/arch/mips/Makefile
-+++ linux-2.6.24.7/arch/mips/Makefile
-@@ -543,6 +543,10 @@ core-$(CONFIG_BCM47XX) += arch/mips/bcm
- cflags-$(CONFIG_BCM47XX) += -Iinclude/asm-mips/mach-bcm47xx
- load-$(CONFIG_BCM47XX) := 0xffffffff80001000
-
-+core-$(CONFIG_BCM963XX) += arch/mips/bcm963xx/
-+cflags-$(CONFIG_BCM963XX) += -Iinclude/asm-mips/mach-bcm963xx
-+load-$(CONFIG_BCM963XX) := 0xffffffff8001000
-+
- #
- # SNI RM
- #
-Index: linux-2.6.24.7/arch/mips/mm/c-r4k.c
-===================================================================
---- linux-2.6.24.7.orig/arch/mips/mm/c-r4k.c
-+++ linux-2.6.24.7/arch/mips/mm/c-r4k.c
-@@ -878,6 +878,13 @@ static void __init probe_pcache(void)
- if (!(config & MIPS_CONF_M))
- panic("Don't know how to probe P-caches on this cpu.");
-
-+ if (c->cputype == CPU_BCM6338 || c->cputype == CPU_BCM6345 || c->cputype == CPU_BCM6348 || c->cputype == CPU_BCM6358)
-+ {
-+ printk("bcm963xx: enabling icache and dcache...\n");
-+ /* Enable caches */
-+ write_c0_diag(read_c0_diag() | 0xC0000000);
-+ }
-+
- /*
- * So we seem to be a MIPS32 or MIPS64 CPU
- * So let's probe the I-cache ...
-Index: linux-2.6.24.7/arch/mips/mm/tlbex.c
-===================================================================
---- linux-2.6.24.7.orig/arch/mips/mm/tlbex.c
-+++ linux-2.6.24.7/arch/mips/mm/tlbex.c
-@@ -909,6 +909,10 @@ static __init void build_tlb_write_entry
- case CPU_25KF:
- case CPU_BCM3302:
- case CPU_BCM4710:
-+// case CPU_BCM6338:
-+ case CPU_BCM6345:
-+ case CPU_BCM6348:
-+ case CPU_BCM6358:
- case CPU_LOONGSON2:
- if (m4kc_tlbp_war())
- i_nop(p);
-Index: linux-2.6.24.7/arch/mips/pci/Makefile
-===================================================================
---- linux-2.6.24.7.orig/arch/mips/pci/Makefile
-+++ linux-2.6.24.7/arch/mips/pci/Makefile
-@@ -48,3 +48,4 @@ obj-$(CONFIG_TOSHIBA_RBTX4938) += fixup-
- obj-$(CONFIG_VICTOR_MPC30X) += fixup-mpc30x.o
- obj-$(CONFIG_ZAO_CAPCELLA) += fixup-capcella.o
- obj-$(CONFIG_WR_PPMC) += fixup-wrppmc.o
-+obj-$(CONFIG_BCM963XX) += fixup-bcm96348.o pci-bcm96348.o ops-bcm96348.o
-Index: linux-2.6.24.7/include/asm-mips/bootinfo.h
-===================================================================
---- linux-2.6.24.7.orig/include/asm-mips/bootinfo.h
-+++ linux-2.6.24.7/include/asm-mips/bootinfo.h
-@@ -197,6 +197,10 @@
- */
- #define MACH_GROUP_BRCM 23 /* Broadcom */
- #define MACH_BCM47XX 1 /* Broadcom BCM47XX */
-+#define MACH_BCM96338 2
-+#define MACH_BCM96345 3
-+#define MACH_BCM96348 4
-+#define MACH_BCM96358 5
-
- #define CL_SIZE COMMAND_LINE_SIZE
-
-Index: linux-2.6.24.7/include/asm-mips/cpu.h
-===================================================================
---- linux-2.6.24.7.orig/include/asm-mips/cpu.h
-+++ linux-2.6.24.7/include/asm-mips/cpu.h
-@@ -111,6 +111,10 @@
-
- #define PRID_IMP_BCM4710 0x4000
- #define PRID_IMP_BCM3302 0x9000
-+//#define PRID_IMP_BCM6338 0x9000
-+#define PRID_IMP_BCM6345 0x8000
-+#define PRID_IMP_BCM6348 0x9100
-+#define PRID_IMP_BCM6358 0xA000
-
- /*
- * Definitions for 7:0 on legacy processors
-@@ -196,7 +200,8 @@ enum cpu_type_enum {
- */
- CPU_4KC, CPU_4KEC, CPU_4KSC, CPU_24K, CPU_34K, CPU_74K, CPU_AU1000,
- CPU_AU1100, CPU_AU1200, CPU_AU1500, CPU_AU1550, CPU_PR4450,
-- CPU_BCM3302, CPU_BCM4710,
-+ CPU_BCM3302, CPU_BCM4710, CPU_BCM6338, CPU_BCM6345, CPU_BCM6348,
-+ CPU_BCM6358,
-
- /*
- * MIPS64 class processors
+++ /dev/null
-Index: linux-2.6.24.7/drivers/serial/Makefile
-===================================================================
---- linux-2.6.24.7.orig/drivers/serial/Makefile
-+++ linux-2.6.24.7/drivers/serial/Makefile
-@@ -65,3 +65,4 @@ obj-$(CONFIG_SERIAL_NETX) += netx-serial
- obj-$(CONFIG_SERIAL_OF_PLATFORM) += of_serial.o
- obj-$(CONFIG_SERIAL_KS8695) += serial_ks8695.o
- obj-$(CONFIG_SERIAL_QE) += ucc_uart.o
-+obj-$(CONFIG_BCM963XX) += bcm63xx_cons.o
+++ /dev/null
-Index: linux-2.6.24.7/drivers/mtd/maps/Kconfig
-===================================================================
---- linux-2.6.24.7.orig/drivers/mtd/maps/Kconfig
-+++ linux-2.6.24.7/drivers/mtd/maps/Kconfig
-@@ -269,6 +269,13 @@ config MTD_MTX1
- Flash memory access on 4G Systems MTX-1 Board. If you have one of
- these boards and would like to use the flash chips on it, say 'Y'.
-
-+config MTD_BCM963XX
-+ tristate "BCM963xx Flash device"
-+ depends on MIPS && BCM963XX
-+ help
-+ Flash memory access on BCM963xx boards. Currently only works with
-+ RedBoot and CFE.
-+
- config MTD_DILNETPC
- tristate "CFI Flash device mapped on DIL/Net PC"
- depends on X86 && MTD_CONCAT && MTD_PARTITIONS && MTD_CFI_INTELEXT
-Index: linux-2.6.24.7/drivers/mtd/redboot.c
-===================================================================
---- linux-2.6.24.7.orig/drivers/mtd/redboot.c
-+++ linux-2.6.24.7/drivers/mtd/redboot.c
-@@ -39,7 +39,7 @@ static inline int redboot_checksum(struc
- return 1;
- }
-
--static int parse_redboot_partitions(struct mtd_info *master,
-+int parse_redboot_partitions(struct mtd_info *master,
- struct mtd_partition **pparts,
- unsigned long fis_origin)
- {
-@@ -146,6 +146,14 @@ static int parse_redboot_partitions(stru
- goto out;
- }
-
-+ if (!fis_origin) {
-+ for (i = 0; i < numslots; i++) {
-+ if (!strncmp(buf[i].name, "RedBoot", 8)) {
-+ fis_origin = (buf[i].flash_base & (master->size << 1) - 1);
-+ }
-+ }
-+ }
-+
- for (i = 0; i < numslots; i++) {
- struct fis_list *new_fl, **prev;
-
-@@ -168,9 +176,8 @@ static int parse_redboot_partitions(stru
- new_fl->img = &buf[i];
- if (fis_origin) {
- buf[i].flash_base -= fis_origin;
-- } else {
-- buf[i].flash_base &= master->size-1;
- }
-+ buf[i].flash_base &= (master->size << 1) - 1;
-
- /* I'm sure the JFFS2 code has done me permanent damage.
- * I now think the following is _normal_
-Index: linux-2.6.24.7/drivers/mtd/maps/Makefile
-===================================================================
---- linux-2.6.24.7.orig/drivers/mtd/maps/Makefile
-+++ linux-2.6.24.7/drivers/mtd/maps/Makefile
-@@ -69,3 +69,4 @@ obj-$(CONFIG_MTD_PLATRAM) += plat-ram.o
- obj-$(CONFIG_MTD_OMAP_NOR) += omap_nor.o
- obj-$(CONFIG_MTD_MTX1) += mtx-1_flash.o
- obj-$(CONFIG_MTD_INTEL_VR_NOR) += intel_vr_nor.o
-+obj-$(CONFIG_MTD_BCM963XX) += bcm963xx-flash.o
projects / openwrt / openwrt.git / commitdiff