Remove patches adding support for MT7621 which have been merged upsteam.
Patches for MT7981 and MT7986 have been merged too, but not in time to
be included in the 2022.10 release, so we have to keep carrying them
until the 2023.01 release.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/kernel.mk
-PKG_VERSION:=2022.07
-PKG_HASH:=92b08eb49c24da14c1adbf70a71ae8f37cc53eeb4230e859ad8b6733d13dcf5e
+PKG_VERSION:=2022.10
+PKG_HASH:=50b4482a505bc281ba8470c399a3c26e145e29b23500bc35c50debd7fa46bdf8
PKG_BUILD_DEPENDS:=arm-trusted-firmware-tools/host
include $(INCLUDE_DIR)/u-boot.mk
+++ /dev/null
-From 1d4fcea788e579934a1ad0a90cecd6e1761127d1 Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Tue, 2 Mar 2021 15:56:17 +0800
-Subject: [PATCH 03/12] mmc: mtk-sd: increase the minimum bus frequency
-
-With a 48MHz input clock, the lowest bus frequency can be as low as
-48000000 / (4 * 4095) = 2930Hz. Such an extremely low frequency will cause
-the mmc framework take seconds to finish the initialization.
-
-Limiting the minimum bus frequency to a slightly higher value can solve the
-issue without any side effects.
-
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- drivers/mmc/mtk-sd.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/mmc/mtk-sd.c
-+++ b/drivers/mmc/mtk-sd.c
-@@ -232,7 +232,7 @@
-
- #define SCLK_CYCLES_SHIFT 20
-
--#define MIN_BUS_CLK 200000
-+#define MIN_BUS_CLK 260000
-
- #define CMD_INTS_MASK \
- (MSDC_INT_CMDRDY | MSDC_INT_RSPCRCERR | MSDC_INT_CMDTMO)
+++ /dev/null
-From 632f09f140610cf45da1dba25c66e9ca79a70a15 Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Wed, 3 Mar 2021 12:12:39 +0800
-Subject: [PATCH 09/12] configs: mt7629: remove unused options and add dm
- command
-
-Remove unused bootm options
-Add dm command
-
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- configs/mt7629_rfb_defconfig | 5 +++++
- 1 file changed, 5 insertions(+)
-
---- a/configs/mt7629_rfb_defconfig
-+++ b/configs/mt7629_rfb_defconfig
-@@ -29,9 +29,14 @@ CONFIG_SPL_WATCHDOG=y
- CONFIG_HUSH_PARSER=y
- CONFIG_SYS_PROMPT="U-Boot> "
- CONFIG_CMD_BOOTMENU=y
-+# CONFIG_BOOTM_NETBSD is not set
-+# CONFIG_BOOTM_PLAN9 is not set
-+# CONFIG_BOOTM_RTEMS is not set
-+# CONFIG_BOOTM_VXWORKS is not set
- # CONFIG_CMD_ELF is not set
- # CONFIG_CMD_XIMG is not set
- CONFIG_CMD_BIND=y
-+CONFIG_CMD_DM=y
- # CONFIG_CMD_FLASH is not set
- CONFIG_CMD_GPIO=y
- CONFIG_CMD_SF_TEST=y
CONFIG_DEFAULT_DEVICE_TREE="mt7622-rfb"
+CONFIG_ENV_SIZE=0x20000
+CONFIG_ENV_OFFSET=0x280000
+ CONFIG_SYS_PROMPT="MT7622> "
CONFIG_DEBUG_UART_BASE=0x11002000
CONFIG_DEBUG_UART_CLOCK=25000000
- CONFIG_SYS_LOAD_ADDR=0x4007ff28
-@@ -21,6 +23,9 @@ CONFIG_CMD_SF_TEST=y
+@@ -23,6 +25,9 @@ CONFIG_CMD_SF_TEST=y
CONFIG_CMD_PING=y
CONFIG_CMD_SMC=y
CONFIG_ENV_OVERWRITE=y
+++ /dev/null
-From 65a4a80157bacde3cf86ce8cbc9a08f5f05ad9bb Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:21:34 +0800
-Subject: [PATCH 01/25] mips: add asm/mipsmtregs.h for MIPS multi-threading
-
-To be compatible with old u-boot used by lots of MT7621 devices, the u-boot
-needs to boot-up MT7621's all cores, and all VPES of each core.
-
-This patch adds asm/mipsmtregs.h from linux kernel which is need for
-boot-up VPEs.
-
-Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- arch/mips/include/asm/mipsmtregs.h | 142 +++++++++++++++++++++++++++++
- 1 file changed, 142 insertions(+)
- create mode 100644 arch/mips/include/asm/mipsmtregs.h
-
---- /dev/null
-+++ b/arch/mips/include/asm/mipsmtregs.h
-@@ -0,0 +1,142 @@
-+/* SPDX-License-Identifier: GPL-2.0 */
-+/*
-+ * MT regs definitions, follows on from mipsregs.h
-+ * Copyright (C) 2004 - 2005 MIPS Technologies, Inc. All rights reserved.
-+ * Elizabeth Clarke et. al.
-+ *
-+ */
-+#ifndef _ASM_MIPSMTREGS_H
-+#define _ASM_MIPSMTREGS_H
-+
-+#include <asm/mipsregs.h>
-+
-+/*
-+ * Macros for use in assembly language code
-+ */
-+
-+#define CP0_MVPCONTROL $0, 1
-+#define CP0_MVPCONF0 $0, 2
-+#define CP0_MVPCONF1 $0, 3
-+#define CP0_VPECONTROL $1, 1
-+#define CP0_VPECONF0 $1, 2
-+#define CP0_VPECONF1 $1, 3
-+#define CP0_YQMASK $1, 4
-+#define CP0_VPESCHEDULE $1, 5
-+#define CP0_VPESCHEFBK $1, 6
-+#define CP0_TCSTATUS $2, 1
-+#define CP0_TCBIND $2, 2
-+#define CP0_TCRESTART $2, 3
-+#define CP0_TCHALT $2, 4
-+#define CP0_TCCONTEXT $2, 5
-+#define CP0_TCSCHEDULE $2, 6
-+#define CP0_TCSCHEFBK $2, 7
-+#define CP0_SRSCONF0 $6, 1
-+#define CP0_SRSCONF1 $6, 2
-+#define CP0_SRSCONF2 $6, 3
-+#define CP0_SRSCONF3 $6, 4
-+#define CP0_SRSCONF4 $6, 5
-+
-+/* MVPControl fields */
-+#define MVPCONTROL_EVP (_ULCAST_(1))
-+
-+#define MVPCONTROL_VPC_SHIFT 1
-+#define MVPCONTROL_VPC (_ULCAST_(1) << MVPCONTROL_VPC_SHIFT)
-+
-+#define MVPCONTROL_STLB_SHIFT 2
-+#define MVPCONTROL_STLB (_ULCAST_(1) << MVPCONTROL_STLB_SHIFT)
-+
-+/* MVPConf0 fields */
-+#define MVPCONF0_PTC_SHIFT 0
-+#define MVPCONF0_PTC (_ULCAST_(0xff))
-+#define MVPCONF0_PVPE_SHIFT 10
-+#define MVPCONF0_PVPE (_ULCAST_(0xf) << MVPCONF0_PVPE_SHIFT)
-+#define MVPCONF0_TCA_SHIFT 15
-+#define MVPCONF0_TCA (_ULCAST_(1) << MVPCONF0_TCA_SHIFT)
-+#define MVPCONF0_PTLBE_SHIFT 16
-+#define MVPCONF0_PTLBE (_ULCAST_(0x3ff) << MVPCONF0_PTLBE_SHIFT)
-+#define MVPCONF0_TLBS_SHIFT 29
-+#define MVPCONF0_TLBS (_ULCAST_(1) << MVPCONF0_TLBS_SHIFT)
-+#define MVPCONF0_M_SHIFT 31
-+#define MVPCONF0_M (_ULCAST_(0x1) << MVPCONF0_M_SHIFT)
-+
-+/* config3 fields */
-+#define CONFIG3_MT_SHIFT 2
-+#define CONFIG3_MT (_ULCAST_(1) << CONFIG3_MT_SHIFT)
-+
-+/* VPEControl fields (per VPE) */
-+#define VPECONTROL_TARGTC (_ULCAST_(0xff))
-+
-+#define VPECONTROL_TE_SHIFT 15
-+#define VPECONTROL_TE (_ULCAST_(1) << VPECONTROL_TE_SHIFT)
-+#define VPECONTROL_EXCPT_SHIFT 16
-+#define VPECONTROL_EXCPT (_ULCAST_(0x7) << VPECONTROL_EXCPT_SHIFT)
-+
-+/* Thread Exception Codes for EXCPT field */
-+#define THREX_TU 0
-+#define THREX_TO 1
-+#define THREX_IYQ 2
-+#define THREX_GSX 3
-+#define THREX_YSCH 4
-+#define THREX_GSSCH 5
-+
-+#define VPECONTROL_GSI_SHIFT 20
-+#define VPECONTROL_GSI (_ULCAST_(1) << VPECONTROL_GSI_SHIFT)
-+#define VPECONTROL_YSI_SHIFT 21
-+#define VPECONTROL_YSI (_ULCAST_(1) << VPECONTROL_YSI_SHIFT)
-+
-+/* VPEConf0 fields (per VPE) */
-+#define VPECONF0_VPA_SHIFT 0
-+#define VPECONF0_VPA (_ULCAST_(1) << VPECONF0_VPA_SHIFT)
-+#define VPECONF0_MVP_SHIFT 1
-+#define VPECONF0_MVP (_ULCAST_(1) << VPECONF0_MVP_SHIFT)
-+#define VPECONF0_XTC_SHIFT 21
-+#define VPECONF0_XTC (_ULCAST_(0xff) << VPECONF0_XTC_SHIFT)
-+
-+/* VPEConf1 fields (per VPE) */
-+#define VPECONF1_NCP1_SHIFT 0
-+#define VPECONF1_NCP1 (_ULCAST_(0xff) << VPECONF1_NCP1_SHIFT)
-+#define VPECONF1_NCP2_SHIFT 10
-+#define VPECONF1_NCP2 (_ULCAST_(0xff) << VPECONF1_NCP2_SHIFT)
-+#define VPECONF1_NCX_SHIFT 20
-+#define VPECONF1_NCX (_ULCAST_(0xff) << VPECONF1_NCX_SHIFT)
-+
-+/* TCStatus fields (per TC) */
-+#define TCSTATUS_TASID (_ULCAST_(0xff))
-+#define TCSTATUS_IXMT_SHIFT 10
-+#define TCSTATUS_IXMT (_ULCAST_(1) << TCSTATUS_IXMT_SHIFT)
-+#define TCSTATUS_TKSU_SHIFT 11
-+#define TCSTATUS_TKSU (_ULCAST_(3) << TCSTATUS_TKSU_SHIFT)
-+#define TCSTATUS_A_SHIFT 13
-+#define TCSTATUS_A (_ULCAST_(1) << TCSTATUS_A_SHIFT)
-+#define TCSTATUS_DA_SHIFT 15
-+#define TCSTATUS_DA (_ULCAST_(1) << TCSTATUS_DA_SHIFT)
-+#define TCSTATUS_DT_SHIFT 20
-+#define TCSTATUS_DT (_ULCAST_(1) << TCSTATUS_DT_SHIFT)
-+#define TCSTATUS_TDS_SHIFT 21
-+#define TCSTATUS_TDS (_ULCAST_(1) << TCSTATUS_TDS_SHIFT)
-+#define TCSTATUS_TSST_SHIFT 22
-+#define TCSTATUS_TSST (_ULCAST_(1) << TCSTATUS_TSST_SHIFT)
-+#define TCSTATUS_RNST_SHIFT 23
-+#define TCSTATUS_RNST (_ULCAST_(3) << TCSTATUS_RNST_SHIFT)
-+/* Codes for RNST */
-+#define TC_RUNNING 0
-+#define TC_WAITING 1
-+#define TC_YIELDING 2
-+#define TC_GATED 3
-+
-+#define TCSTATUS_TMX_SHIFT 27
-+#define TCSTATUS_TMX (_ULCAST_(1) << TCSTATUS_TMX_SHIFT)
-+/* TCStatus TCU bits can use same definitions/offsets as CU bits in Status */
-+
-+/* TCBind */
-+#define TCBIND_CURVPE_SHIFT 0
-+#define TCBIND_CURVPE (_ULCAST_(0xf))
-+
-+#define TCBIND_CURTC_SHIFT 21
-+
-+#define TCBIND_CURTC (_ULCAST_(0xff) << TCBIND_CURTC_SHIFT)
-+
-+/* TCHalt */
-+#define TCHALT_H (_ULCAST_(1))
-+
-+#endif
+++ /dev/null
-From be570e7b0ce004127a7cc97bfae30037fc42a340 Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:21:39 +0800
-Subject: [PATCH 02/25] mips: add more definitions for asm/cm.h
-
-This patch add more definitions needed for MT7621 initialization.
-MT7621 needs to initialize GIC/CPC and other related parts.
-
-Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- arch/mips/include/asm/cm.h | 67 ++++++++++++++++++++++++++++++++++++++
- 1 file changed, 67 insertions(+)
-
---- a/arch/mips/include/asm/cm.h
-+++ b/arch/mips/include/asm/cm.h
-@@ -8,9 +8,23 @@
- #define __MIPS_ASM_CM_H__
-
- /* Global Control Register (GCR) offsets */
-+#define GCR_CONFIG 0x0000
- #define GCR_BASE 0x0008
- #define GCR_BASE_UPPER 0x000c
-+#define GCR_CONTROL 0x0010
-+#define GCR_ACCESS 0x0020
- #define GCR_REV 0x0030
-+#define GCR_GIC_BASE 0x0080
-+#define GCR_CPC_BASE 0x0088
-+#define GCR_REG0_BASE 0x0090
-+#define GCR_REG0_MASK 0x0098
-+#define GCR_REG1_BASE 0x00a0
-+#define GCR_REG1_MASK 0x00a8
-+#define GCR_REG2_BASE 0x00b0
-+#define GCR_REG2_MASK 0x00b8
-+#define GCR_REG3_BASE 0x00c0
-+#define GCR_REG3_MASK 0x00c8
-+#define GCR_CPC_STATUS 0x00f0
- #define GCR_L2_CONFIG 0x0130
- #define GCR_L2_TAG_ADDR 0x0600
- #define GCR_L2_TAG_ADDR_UPPER 0x0604
-@@ -19,10 +33,59 @@
- #define GCR_L2_DATA 0x0610
- #define GCR_L2_DATA_UPPER 0x0614
- #define GCR_Cx_COHERENCE 0x2008
-+#define GCR_Cx_OTHER 0x2018
-+#define GCR_Cx_ID 0x2028
-+#define GCR_CO_COHERENCE 0x4008
-+
-+/* GCR_CONFIG fields */
-+#define GCR_CONFIG_NUM_CLUSTERS_SHIFT 23
-+#define GCR_CONFIG_NUM_CLUSTERS (0x7f << 23)
-+#define GCR_CONFIG_NUMIOCU_SHIFT 8
-+#define GCR_CONFIG_NUMIOCU (0xff << 8)
-+#define GCR_CONFIG_PCORES_SHIFT 0
-+#define GCR_CONFIG_PCORES (0xff << 0)
-+
-+/* GCR_BASE fields */
-+#define GCR_BASE_SHIFT 15
-+#define CCA_DEFAULT_OVR_SHIFT 5
-+#define CCA_DEFAULT_OVR_MASK (0x7 << 5)
-+#define CCA_DEFAULT_OVREN (0x1 << 4)
-+#define CM_DEFAULT_TARGET_SHIFT 0
-+#define CM_DEFAULT_TARGET_MASK (0x3 << 0)
-+
-+/* GCR_CONTROL fields */
-+#define GCR_CONTROL_SYNCCTL (0x1 << 16)
-
- /* GCR_REV CM versions */
- #define GCR_REV_CM3 0x0800
-
-+/* GCR_GIC_BASE fields */
-+#define GCR_GIC_BASE_ADDRMASK_SHIFT 7
-+#define GCR_GIC_BASE_ADDRMASK (0x1ffffff << 7)
-+#define GCR_GIC_EN (0x1 << 0)
-+
-+/* GCR_CPC_BASE fields */
-+#define GCR_CPC_BASE_ADDRMASK_SHIFT 15
-+#define GCR_CPC_BASE_ADDRMASK (0x1ffff << 15)
-+#define GCR_CPC_EN (0x1 << 0)
-+
-+/* GCR_REGn_MASK fields */
-+#define GCR_REGn_MASK_ADDRMASK_SHIFT 16
-+#define GCR_REGn_MASK_ADDRMASK (0xffff << 16)
-+#define GCR_REGn_MASK_CCAOVR_SHIFT 5
-+#define GCR_REGn_MASK_CCAOVR (0x7 << 5)
-+#define GCR_REGn_MASK_CCAOVREN (1 << 4)
-+#define GCR_REGn_MASK_DROPL2 (1 << 2)
-+#define GCR_REGn_MASK_CMTGT_SHIFT 0
-+#define GCR_REGn_MASK_CMTGT (0x3 << 0)
-+#define GCR_REGn_MASK_CMTGT_DISABLED 0x0
-+#define GCR_REGn_MASK_CMTGT_MEM 0x1
-+#define GCR_REGn_MASK_CMTGT_IOCU0 0x2
-+#define GCR_REGn_MASK_CMTGT_IOCU1 0x3
-+
-+/* GCR_CPC_STATUS fields */
-+#define GCR_CPC_EX (0x1 << 0)
-+
- /* GCR_L2_CONFIG fields */
- #define GCR_L2_CONFIG_ASSOC_SHIFT 0
- #define GCR_L2_CONFIG_ASSOC_BITS 8
-@@ -36,6 +99,10 @@
- #define GCR_Cx_COHERENCE_DOM_EN (0xff << 0)
- #define GCR_Cx_COHERENCE_EN (0x1 << 0)
-
-+/* GCR_Cx_OTHER fields */
-+#define GCR_Cx_OTHER_CORENUM_SHIFT 16
-+#define GCR_Cx_OTHER_CORENUM (0xffff << 16)
-+
- #ifndef __ASSEMBLY__
-
- #include <asm/io.h>
+++ /dev/null
-From 71ebc3d25147172e219ea87bec061f751257395b Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:21:45 +0800
-Subject: [PATCH 03/25] mips: add __image_copy_len for SPL linker script
-
-This patch adds __image_copy_len needed by TPL of MT7621 SoC.
-The __image_copy_len represents the binary blob size of both SPL/TPL
-binaries. To achieve this, __text_start/end are added for calculation.
-
-Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- arch/mips/cpu/u-boot-spl.lds | 3 +++
- 1 file changed, 3 insertions(+)
-
---- a/arch/mips/cpu/u-boot-spl.lds
-+++ b/arch/mips/cpu/u-boot-spl.lds
-@@ -13,7 +13,9 @@ SECTIONS
-
- . = ALIGN(4);
- .text : {
-+ __text_start = .;
- *(.text*)
-+ __text_end = .;
- } > .spl_mem
-
- . = ALIGN(4);
-@@ -36,6 +38,7 @@ SECTIONS
-
- . = ALIGN(4);
- __image_copy_end = .;
-+ __image_copy_len = __image_copy_end - __text_start;
-
- _image_binary_end = .;
-
+++ /dev/null
-From d7cfa1cb5602a1d936df36ee70869753835de28e Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:21:51 +0800
-Subject: [PATCH 04/25] mips: add support for noncached_alloc()
-
-This patch adds support for noncached_alloc() which was only supported by
-ARM platform.
-
-Unlike the ARM platform, MMU is not used in u-boot for MIPS. Instead, KSEG
-is provided to access uncached memory. So most code of this patch is copied
-from cache.c of ARM platform, with only two differences:
-1. MMU is untouched in noncached_set_region()
-2. Address returned by noncached_alloc() is converted using KSEG1ADDR()
-
-Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- arch/mips/include/asm/system.h | 20 ++++++++++++++++
- arch/mips/lib/cache.c | 43 ++++++++++++++++++++++++++++++++++
- 2 files changed, 63 insertions(+)
-
---- a/arch/mips/include/asm/system.h
-+++ b/arch/mips/include/asm/system.h
-@@ -282,4 +282,24 @@ static inline void instruction_hazard_ba
- : "=&r"(tmp));
- }
-
-+#ifdef CONFIG_SYS_NONCACHED_MEMORY
-+/* 1MB granularity */
-+#define MMU_SECTION_SHIFT 20
-+#define MMU_SECTION_SIZE (1 << MMU_SECTION_SHIFT)
-+
-+/**
-+ * noncached_init() - Initialize non-cached memory region
-+ *
-+ * Initialize non-cached memory area. This memory region will be typically
-+ * located right below the malloc() area and be accessed from KSEG1.
-+ *
-+ * It is called during the generic post-relocation init sequence.
-+ *
-+ * Return: 0 if OK
-+ */
-+int noncached_init(void);
-+
-+phys_addr_t noncached_alloc(size_t size, size_t align);
-+#endif /* CONFIG_SYS_NONCACHED_MEMORY */
-+
- #endif /* _ASM_SYSTEM_H */
---- a/arch/mips/lib/cache.c
-+++ b/arch/mips/lib/cache.c
-@@ -6,6 +6,7 @@
-
- #include <common.h>
- #include <cpu_func.h>
-+#include <malloc.h>
- #include <asm/cache.h>
- #include <asm/cacheops.h>
- #include <asm/cm.h>
-@@ -197,3 +198,45 @@ void dcache_disable(void)
- /* ensure the pipeline doesn't contain now-invalid instructions */
- instruction_hazard_barrier();
- }
-+
-+#ifdef CONFIG_SYS_NONCACHED_MEMORY
-+static unsigned long noncached_start;
-+static unsigned long noncached_end;
-+static unsigned long noncached_next;
-+
-+void noncached_set_region(void)
-+{
-+}
-+
-+int noncached_init(void)
-+{
-+ phys_addr_t start, end;
-+ size_t size;
-+
-+ /* If this calculation changes, update board_f.c:reserve_noncached() */
-+ end = ALIGN(mem_malloc_start, MMU_SECTION_SIZE) - MMU_SECTION_SIZE;
-+ size = ALIGN(CONFIG_SYS_NONCACHED_MEMORY, MMU_SECTION_SIZE);
-+ start = end - size;
-+
-+ debug("mapping memory %pa-%pa non-cached\n", &start, &end);
-+
-+ noncached_start = start;
-+ noncached_end = end;
-+ noncached_next = start;
-+
-+ return 0;
-+}
-+
-+phys_addr_t noncached_alloc(size_t size, size_t align)
-+{
-+ phys_addr_t next = ALIGN(noncached_next, align);
-+
-+ if (next >= noncached_end || (noncached_end - next) < size)
-+ return 0;
-+
-+ debug("allocated %zu bytes of uncached memory @%pa\n", size, &next);
-+ noncached_next = next + size;
-+
-+ return CKSEG1ADDR(next);
-+}
-+#endif /* CONFIG_SYS_NONCACHED_MEMORY */
+++ /dev/null
-From e0c82f36ad5180d9582d353407ff1bf34a2734bb Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:22:21 +0800
-Subject: [PATCH 05/25] mips: mtmips: add support for MediaTek MT7621 SoC
-
-This patch adds support for MediaTek MT7621 SoC.
-All files are dedicated for u-boot.
-
-The default build target is u-boot-mt7621.bin.
-
-The specification of this chip:
-https://www.mediatek.com/products/homenetworking/mt7621
-
-Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- arch/mips/dts/mt7621-u-boot.dtsi | 111 ++++++
- arch/mips/dts/mt7621.dtsi | 349 +++++++++++++++++++
- arch/mips/mach-mtmips/Kconfig | 49 ++-
- arch/mips/mach-mtmips/Makefile | 4 +
- arch/mips/mach-mtmips/cpu.c | 2 +-
- arch/mips/mach-mtmips/mt7621/Kconfig | 95 +++++
- arch/mips/mach-mtmips/mt7621/Makefile | 14 +
- arch/mips/mach-mtmips/mt7621/init.c | 246 +++++++++++++
- arch/mips/mach-mtmips/mt7621/mt7621.h | 229 ++++++++++++
- arch/mips/mach-mtmips/mt7621/serial.c | 23 ++
- arch/mips/mach-mtmips/mt7621/spl/Makefile | 9 +
- arch/mips/mach-mtmips/mt7621/spl/cps.c | 153 ++++++++
- arch/mips/mach-mtmips/mt7621/spl/dram.c | 153 ++++++++
- arch/mips/mach-mtmips/mt7621/spl/dram.h | 39 +++
- arch/mips/mach-mtmips/mt7621/spl/launch.c | 100 ++++++
- arch/mips/mach-mtmips/mt7621/spl/launch.h | 52 +++
- arch/mips/mach-mtmips/mt7621/spl/launch_ll.S | 339 ++++++++++++++++++
- arch/mips/mach-mtmips/mt7621/spl/serial.c | 24 ++
- arch/mips/mach-mtmips/mt7621/spl/spl.c | 95 +++++
- arch/mips/mach-mtmips/mt7621/spl/start.S | 226 ++++++++++++
- arch/mips/mach-mtmips/mt7621/sram_init.S | 22 ++
- arch/mips/mach-mtmips/mt7621/tpl/Makefile | 4 +
- arch/mips/mach-mtmips/mt7621/tpl/start.S | 161 +++++++++
- arch/mips/mach-mtmips/mt7621/tpl/tpl.c | 144 ++++++++
- include/configs/mt7621.h | 65 ++++
- 25 files changed, 2702 insertions(+), 6 deletions(-)
- create mode 100644 arch/mips/dts/mt7621-u-boot.dtsi
- create mode 100644 arch/mips/dts/mt7621.dtsi
- create mode 100644 arch/mips/mach-mtmips/mt7621/Kconfig
- create mode 100644 arch/mips/mach-mtmips/mt7621/Makefile
- create mode 100644 arch/mips/mach-mtmips/mt7621/init.c
- create mode 100644 arch/mips/mach-mtmips/mt7621/mt7621.h
- create mode 100644 arch/mips/mach-mtmips/mt7621/serial.c
- create mode 100644 arch/mips/mach-mtmips/mt7621/spl/Makefile
- create mode 100644 arch/mips/mach-mtmips/mt7621/spl/cps.c
- create mode 100644 arch/mips/mach-mtmips/mt7621/spl/dram.c
- create mode 100644 arch/mips/mach-mtmips/mt7621/spl/dram.h
- create mode 100644 arch/mips/mach-mtmips/mt7621/spl/launch.c
- create mode 100644 arch/mips/mach-mtmips/mt7621/spl/launch.h
- create mode 100644 arch/mips/mach-mtmips/mt7621/spl/launch_ll.S
- create mode 100644 arch/mips/mach-mtmips/mt7621/spl/serial.c
- create mode 100644 arch/mips/mach-mtmips/mt7621/spl/spl.c
- create mode 100644 arch/mips/mach-mtmips/mt7621/spl/start.S
- create mode 100644 arch/mips/mach-mtmips/mt7621/sram_init.S
- create mode 100644 arch/mips/mach-mtmips/mt7621/tpl/Makefile
- create mode 100644 arch/mips/mach-mtmips/mt7621/tpl/start.S
- create mode 100644 arch/mips/mach-mtmips/mt7621/tpl/tpl.c
- create mode 100644 include/configs/mt7621.h
-
---- /dev/null
-+++ b/arch/mips/dts/mt7621-u-boot.dtsi
-@@ -0,0 +1,111 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <linux/stringify.h>
-+
-+/ {
-+ binman: binman {
-+ multiple-images;
-+ };
-+};
-+
-+&sysc {
-+ u-boot,dm-pre-reloc;
-+};
-+
-+&reboot {
-+ u-boot,dm-pre-reloc;
-+};
-+
-+&clkctrl {
-+ u-boot,dm-pre-reloc;
-+};
-+
-+&rstctrl {
-+ u-boot,dm-pre-reloc;
-+};
-+
-+&pinctrl {
-+ u-boot,dm-pre-reloc;
-+};
-+
-+&uart0 {
-+ u-boot,dm-pre-reloc;
-+};
-+
-+&uart1 {
-+ u-boot,dm-pre-reloc;
-+};
-+
-+&uart2 {
-+ u-boot,dm-pre-reloc;
-+};
-+
-+&binman {
-+ u-boot-spl-ddr {
-+ align = <4>;
-+ align-size = <4>;
-+ filename = "u-boot-spl-ddr.bin";
-+ pad-byte = <0xff>;
-+
-+ u-boot-spl {
-+ align-end = <4>;
-+ filename = "u-boot-spl.bin";
-+ };
-+
-+ stage_bin {
-+ filename = "mt7621_stage_sram.bin";
-+ type = "blob-ext";
-+ };
-+ };
-+
-+ spl-img {
-+ filename = "u-boot-spl-ddr.img";
-+
-+ mkimage {
-+#ifdef CONFIG_MT7621_BOOT_FROM_NAND
-+ args = "-T", "mtk_image", "-n", "mt7621=1",
-+ "-a", __stringify(CONFIG_SPL_TEXT_BASE),
-+ "-e", __stringify(CONFIG_SPL_TEXT_BASE);
-+#else
-+ args = "-A", "mips", "-T", "standalone", "-O", "u-boot",
-+ "-C", "none", "-n", "MT7621 U-Boot SPL",
-+ "-a", __stringify(CONFIG_SPL_TEXT_BASE),
-+ "-e", __stringify(CONFIG_SPL_TEXT_BASE);
-+#endif
-+
-+ blob {
-+ filename = "u-boot-spl-ddr.bin";
-+ };
-+ };
-+ };
-+
-+ mt7621-uboot {
-+ filename = "u-boot-mt7621.bin";
-+ pad-byte = <0xff>;
-+
-+#ifndef CONFIG_MT7621_BOOT_FROM_NAND
-+ u-boot-tpl {
-+ align-end = <4>;
-+ filename = "u-boot-tpl.bin";
-+ };
-+#endif
-+
-+ spl {
-+#ifdef CONFIG_MT7621_BOOT_FROM_NAND
-+ align-end = <0x1000>;
-+#endif
-+ filename = "u-boot-spl-ddr.img";
-+ type = "blob";
-+ };
-+
-+ u-boot {
-+ filename = "u-boot-lzma.img";
-+ type = "blob";
-+ };
-+ };
-+};
---- /dev/null
-+++ b/arch/mips/dts/mt7621.dtsi
-@@ -0,0 +1,349 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <dt-bindings/clock/mt7621-clk.h>
-+#include <dt-bindings/reset/mt7621-reset.h>
-+#include <dt-bindings/phy/phy.h>
-+
-+/ {
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ compatible = "mediatek,mt7621-soc";
-+
-+ cpus {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ cpu@0 {
-+ device_type = "cpu";
-+ compatible = "mips,mips1004Kc";
-+ reg = <0>;
-+ };
-+
-+ cpu@1 {
-+ device_type = "cpu";
-+ compatible = "mips,mips1004Kc";
-+ reg = <1>;
-+ };
-+ };
-+
-+ clk48m: clk48m {
-+ compatible = "fixed-clock";
-+
-+ clock-frequency = <48000000>;
-+
-+ #clock-cells = <0>;
-+ };
-+
-+ clk50m: clk50m {
-+ compatible = "fixed-clock";
-+
-+ clock-frequency = <50000000>;
-+
-+ #clock-cells = <0>;
-+ };
-+
-+ sysc: sysctrl@1e000000 {
-+ compatible = "mediatek,mt7621-sysc", "syscon";
-+ reg = <0x1e000000 0x100>;
-+
-+ clkctrl: clock-controller@1e000030 {
-+ compatible = "mediatek,mt7621-clk";
-+ mediatek,memc = <&memc>;
-+
-+ #clock-cells = <1>;
-+ };
-+ };
-+
-+ rstctrl: reset-controller@1e000034 {
-+ compatible = "mediatek,mtmips-reset";
-+ reg = <0x1e000034 0x4>;
-+ #reset-cells = <1>;
-+ };
-+
-+ reboot: resetctl-reboot {
-+ compatible = "resetctl-reboot";
-+
-+ resets = <&rstctrl RST_SYS>;
-+ reset-names = "sysreset";
-+ };
-+
-+ memc: memctrl@1e005000 {
-+ compatible = "mediatek,mt7621-memc", "syscon";
-+ reg = <0x1e005000 0x1000>;
-+ };
-+
-+ pinctrl: pinctrl@1e000060 {
-+ compatible = "mediatek,mt7621-pinctrl";
-+ reg = <0x1e000048 0x30>;
-+
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&state_default>;
-+
-+ state_default: pin_state {
-+ };
-+
-+ uart1_pins: uart1_pins {
-+ groups = "uart1";
-+ function = "uart";
-+ };
-+
-+ uart2_pins: uart2_pins {
-+ groups = "uart2";
-+ function = "uart";
-+ };
-+
-+ uart3_pins: uart3_pins {
-+ groups = "uart3";
-+ function = "uart";
-+ };
-+
-+ sdxc_pins: sdxc_pins {
-+ groups = "sdxc";
-+ function = "sdxc";
-+ };
-+
-+ spi_pins: spi_pins {
-+ groups = "spi";
-+ function = "spi";
-+ };
-+
-+ eth_pins: eth_pins {
-+ mdio_pins {
-+ groups = "mdio";
-+ function = "mdio";
-+ };
-+
-+ rgmii1_pins {
-+ groups = "rgmii1";
-+ function = "rgmii";
-+ };
-+
-+ esw_pins {
-+ groups = "esw int";
-+ function = "esw int";
-+ };
-+
-+ mdio_pconf {
-+ groups = "mdio";
-+ drive-strength = <2>;
-+ };
-+ };
-+ };
-+
-+ watchdog: watchdog@1e000100 {
-+ compatible = "mediatek,mt7621-wdt";
-+ reg = <0x1e000100 0x40>;
-+
-+ resets = <&rstctrl RST_TIMER>;
-+ reset-names = "wdt";
-+
-+ status = "disabled";
-+ };
-+
-+ gpio: gpio@1e000600 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ compatible = "mtk,mt7621-gpio";
-+ reg = <0x1e000600 0x100>;
-+
-+ resets = <&rstctrl RST_PIO>;
-+ reset-names = "pio";
-+
-+ gpio0: bank@0 {
-+ reg = <0>;
-+ compatible = "mtk,mt7621-gpio-bank";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ };
-+
-+ gpio1: bank@1 {
-+ reg = <1>;
-+ compatible = "mtk,mt7621-gpio-bank";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ };
-+
-+ gpio2: bank@2 {
-+ reg = <2>;
-+ compatible = "mtk,mt7621-gpio-bank";
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ };
-+ };
-+
-+ spi: spi@1e000b00 {
-+ compatible = "ralink,mt7621-spi";
-+ reg = <0x1e000b00 0x40>;
-+
-+ status = "disabled";
-+
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&spi_pins>;
-+
-+ resets = <&rstctrl RST_SPI>;
-+ reset-names = "spi";
-+
-+ clocks = <&clkctrl MT7621_CLK_SPI>;
-+
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ };
-+
-+ uart0: uart1@1e000c00 {
-+ compatible = "mediatek,hsuart", "ns16550a";
-+ reg = <0x1e000c00 0x100>;
-+
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&uart1_pins>;
-+
-+ clocks = <&clkctrl MT7621_CLK_UART1>;
-+
-+ resets = <&rstctrl RST_UART1>;
-+
-+ reg-shift = <2>;
-+ };
-+
-+ uart1: uart2@1e000d00 {
-+ compatible = "mediatek,hsuart", "ns16550a";
-+ reg = <0x1e000d00 0x100>;
-+
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&uart2_pins>;
-+
-+ clocks = <&clkctrl MT7621_CLK_UART2>;
-+
-+ resets = <&rstctrl RST_UART2>;
-+
-+ reg-shift = <2>;
-+
-+ status = "disabled";
-+ };
-+
-+ uart2: uart3@1e000e00 {
-+ compatible = "mediatek,hsuart", "ns16550a";
-+ reg = <0x1e000e00 0x100>;
-+
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&uart3_pins>;
-+
-+ clocks = <&clkctrl MT7621_CLK_UART3>;
-+
-+ resets = <&rstctrl RST_UART3>;
-+
-+ reg-shift = <2>;
-+
-+ status = "disabled";
-+ };
-+
-+ eth: eth@1e100000 {
-+ compatible = "mediatek,mt7621-eth";
-+ reg = <0x1e100000 0x20000>;
-+ mediatek,ethsys = <&sysc>;
-+
-+ pinctrl-names = "default";
-+ pinctrl-0 = <ð_pins>;
-+
-+ resets = <&rstctrl RST_FE>, <&rstctrl RST_GMAC>, <&rstctrl RST_MCM>;
-+ reset-names = "fe", "gmac", "mcm";
-+
-+ clocks = <&clkctrl MT7621_CLK_GDMA>,
-+ <&clkctrl MT7621_CLK_ETH>;
-+ clock-names = "gmac", "fe";
-+
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ mediatek,gmac-id = <0>;
-+ phy-mode = "rgmii";
-+ mediatek,switch = "mt7530";
-+ mediatek,mcm;
-+
-+ fixed-link {
-+ speed = <1000>;
-+ full-duplex;
-+ };
-+ };
-+
-+ mmc: mmc@1e130000 {
-+ compatible = "mediatek,mt7621-mmc";
-+ reg = <0x1e130000 0x4000>;
-+
-+ status = "disabled";
-+
-+ bus-width = <4>;
-+ builtin-cd = <1>;
-+ r_smpl = <1>;
-+
-+ pinctrl-names = "default";
-+ pinctrl-0 = <&sdxc_pins>;
-+
-+ clocks = <&clk50m>, <&clkctrl MT7621_CLK_SHXC>;
-+ clock-names = "source", "hclk";
-+
-+ resets = <&rstctrl RST_SDXC>;
-+ };
-+
-+ ssusb: usb@1e1c0000 {
-+ compatible = "mediatek,mt7621-xhci", "mediatek,mtk-xhci";
-+ reg = <0x1e1c0000 0x1000>, <0x1e1d0700 0x100>;
-+ reg-names = "mac", "ippc";
-+
-+ clocks = <&clk48m>, <&clk48m>;
-+ clock-names = "sys_ck", "ref_ck";
-+
-+ phys = <&u2port0 PHY_TYPE_USB2>,
-+ <&u3port0 PHY_TYPE_USB3>,
-+ <&u2port1 PHY_TYPE_USB2>;
-+
-+ status = "disabled";
-+ };
-+
-+ u3phy: usb-phy@1e1d0000 {
-+ compatible = "mediatek,mt7621-u3phy",
-+ "mediatek,generic-tphy-v1";
-+ reg = <0x1e1d0000 0x700>;
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ ranges;
-+ status = "disabled";
-+
-+ u2port0: usb-phy@1e1d0800 {
-+ reg = <0x1e1d0800 0x0100>;
-+ #phy-cells = <1>;
-+ clocks = <&clk48m>;
-+ clock-names = "ref";
-+ };
-+
-+ u3port0: usb-phy@1e1d0900 {
-+ reg = <0x1e1d0900 0x0100>;
-+ #phy-cells = <1>;
-+ };
-+
-+ u2port1: usb-phy@1e1d1000 {
-+ reg = <0x1e1d1000 0x0100>;
-+ #phy-cells = <1>;
-+ clocks = <&clk48m>;
-+ clock-names = "ref";
-+ };
-+ };
-+
-+ i2c: i2c@1e000900 {
-+ compatible = "i2c-gpio";
-+
-+ status = "disabled";
-+
-+ i2c-gpio,delay-us = <3>;
-+
-+ gpios = <&gpio0 3 1>, /* PIN3 as SDA */
-+ <&gpio0 4 1>; /* PIN4 as CLK */
-+
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ };
-+};
---- a/arch/mips/mach-mtmips/Kconfig
-+++ b/arch/mips/mach-mtmips/Kconfig
-@@ -9,6 +9,7 @@ config SYS_MALLOC_F_LEN
-
- config SYS_SOC
- default "mt7620" if SOC_MT7620
-+ default "mt7621" if SOC_MT7621
- default "mt7628" if SOC_MT7628
-
- config SYS_DCACHE_SIZE
-@@ -18,25 +19,45 @@ config SYS_DCACHE_LINE_SIZE
- default 32
-
- config SYS_ICACHE_SIZE
-- default 65536
-+ default 65536 if SOC_MT7620 || SOC_MT7628
-+ default 32768 if SOC_MT7621
-
- config SYS_ICACHE_LINE_SIZE
- default 32
-
-+config SYS_SCACHE_LINE_SIZE
-+ default 32 if SOC_MT7621
-+
- config SYS_TEXT_BASE
-- default 0x9c000000 if !SPL
-- default 0x80200000 if SPL
-+ default 0x9c000000 if !SPL && !SOC_MT7621
-+ default 0x80200000 if SPL || SOC_MT7621
-
- config SPL_TEXT_BASE
-- default 0x9c000000
-+ default 0x9c000000 if !SOC_MT7621
-+ default 0x80100000 if SOC_MT7621
-+
-+config SPL_SIZE_LIMIT
-+ default 0x30000 if SOC_MT7621
-+
-+config TPL_TEXT_BASE
-+ default 0xbfc00000 if SOC_MT7621
-+
-+config TPL_MAX_SIZE
-+ default 4096 if SOC_MT7621
-
- config SPL_PAYLOAD
- default "u-boot-lzma.img" if SPL_LZMA
-
- config BUILD_TARGET
-- default "u-boot-with-spl.bin" if SPL
-+ default "u-boot-with-spl.bin" if SPL && !SOC_MT7621
-+ default "u-boot-lzma.img" if SOC_MT7621
- default "u-boot.bin"
-
-+config MAX_MEM_SIZE
-+ int
-+ default 256 if SOC_MT7620 || SOC_MT7628
-+ default 512 if SOC_MT7621
-+
- choice
- prompt "MediaTek MIPS SoC select"
-
-@@ -55,6 +76,23 @@ config SOC_MT7620
- help
- This supports MediaTek MT7620.
-
-+config SOC_MT7621
-+ bool "MT7621"
-+ select MIPS_CM
-+ select MIPS_L2_CACHE
-+ select SYS_CACHE_SHIFT_5
-+ select SYS_MIPS_CACHE_INIT_RAM_LOAD
-+ select PINCTRL_MT7621
-+ select MTK_SERIAL
-+ select REGMAP
-+ select SYSCON
-+ select BINMAN
-+ select SUPPORT_TPL
-+ select SPL_LOADER_SUPPORT if SPL
-+ select SPL_INIT_STACK_WITHOUT_MALLOC_F if SPL
-+ help
-+ This supports MediaTek MT7621.
-+
- config SOC_MT7628
- bool "MT7628"
- select SYS_CACHE_SHIFT_5
-@@ -80,6 +118,7 @@ config SOC_MT7628
- endchoice
-
- source "arch/mips/mach-mtmips/mt7620/Kconfig"
-+source "arch/mips/mach-mtmips/mt7621/Kconfig"
- source "arch/mips/mach-mtmips/mt7628/Kconfig"
-
- endmenu
---- a/arch/mips/mach-mtmips/Makefile
-+++ b/arch/mips/mach-mtmips/Makefile
-@@ -1,9 +1,13 @@
- # SPDX-License-Identifier: GPL-2.0+
-
- obj-y += cpu.o
-+
-+ifneq ($(CONFIG_SOC_MT7621),y)
- obj-y += ddr_init.o
- obj-y += ddr_cal.o
- obj-$(CONFIG_SPL_BUILD) += spl.o
-+endif
-
- obj-$(CONFIG_SOC_MT7620) += mt7620/
-+obj-$(CONFIG_SOC_MT7621) += mt7621/
- obj-$(CONFIG_SOC_MT7628) += mt7628/
---- a/arch/mips/mach-mtmips/cpu.c
-+++ b/arch/mips/mach-mtmips/cpu.c
-@@ -16,7 +16,7 @@ DECLARE_GLOBAL_DATA_PTR;
-
- int dram_init(void)
- {
-- gd->ram_size = get_ram_size((void *)KSEG1, SZ_256M);
-+ gd->ram_size = get_ram_size((void *)KSEG1, CONFIG_MAX_MEM_SIZE << 20);
-
- return 0;
- }
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/Kconfig
-@@ -0,0 +1,95 @@
-+
-+if SOC_MT7621
-+
-+menu "CPU & DDR configuration"
-+
-+config MT7621_CPU_FREQ
-+ int "CPU Frequency (MHz)"
-+ range 400 1200
-+ default 880
-+
-+choice
-+ prompt "DRAM Frequency"
-+ default MT7621_DRAM_FREQ_1200
-+
-+config MT7621_DRAM_FREQ_400
-+ bool "400MHz"
-+
-+config MT7621_DRAM_FREQ_800
-+ bool "800MHz"
-+
-+config MT7621_DRAM_FREQ_1066
-+ bool "1066MHz"
-+
-+config MT7621_DRAM_FREQ_1200
-+ bool "1200MHz"
-+
-+endchoice
-+
-+choice
-+ prompt "DDR2 timing parameters"
-+ default MT7621_DRAM_DDR2_1024M
-+
-+config MT7621_DRAM_DDR2_512M
-+ bool "64MB"
-+
-+config MT7621_DRAM_DDR2_1024M
-+ bool "128MB"
-+
-+config MT7621_DRAM_DDR2_512M_W9751G6KB_A02_1066MHZ
-+ bool "W9751G6KB_A02 @ 1066MHz (64MB)"
-+
-+config MT7621_DRAM_DDR2_1024M_W971GG6KB25_800MHZ
-+ bool "W971GG6KB25 @ 800MHz (128MB)"
-+
-+config MT7621_DRAM_DDR2_1024M_W971GG6KB18_1066MHZ
-+ bool "W971GG6KB18 @ 1066MHz (128MB)"
-+
-+endchoice
-+
-+choice
-+ prompt "DDR3 timing parameters"
-+ default MT7621_DRAM_DDR3_2048M
-+
-+config MT7621_DRAM_DDR3_1024M
-+ bool "128MB"
-+
-+config MT7621_DRAM_DDR3_1024M_KGD
-+ bool "128MB KGD (MT7621DA)"
-+
-+config MT7621_DRAM_DDR3_2048M
-+ bool "256MB"
-+
-+config MT7621_DRAM_DDR3_4096M
-+ bool "512MB"
-+
-+endchoice
-+
-+endmenu
-+
-+config DEBUG_UART_BOARD_INIT
-+ default y
-+
-+config MT7621_BOOT_FROM_NAND
-+ bool "Boot from NAND"
-+ help
-+ Select this if u-boot will boot from NAND flash. When booting from
-+ NAND, SPL will be loaded by bootrom directly and no TPL is needed.
-+
-+choice
-+ prompt "Board select"
-+
-+endchoice
-+
-+config SYS_CONFIG_NAME
-+ string "Board configuration name"
-+ default "mt7621" if BOARD_MT7621_RFB || BOARD_MT7621_NAND_RFB
-+
-+config SYS_BOARD
-+ string "Board name"
-+ default "mt7621" if BOARD_MT7621_RFB || BOARD_MT7621_NAND_RFB
-+
-+config SYS_VENDOR
-+ default "mediatek" if BOARD_MT7621_RFB || BOARD_MT7621_NAND_RFB
-+
-+endif
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/Makefile
-@@ -0,0 +1,14 @@
-+# SPDX-License-Identifier: GPL-2.0
-+
-+obj-y += init.o
-+obj-y += serial.o
-+
-+ifeq ($(CONFIG_SPL_BUILD),y)
-+ifeq ($(CONFIG_TPL_BUILD),y)
-+obj-y += tpl/
-+else
-+obj-y += spl/
-+endif
-+
-+obj-y += sram_init.o
-+endif
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/init.c
-@@ -0,0 +1,246 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <clk.h>
-+#include <dm.h>
-+#include <dm/uclass.h>
-+#include <dt-bindings/clock/mt7621-clk.h>
-+#include <asm/global_data.h>
-+#include <linux/io.h>
-+#include <linux/bitfield.h>
-+#include "mt7621.h"
-+
-+DECLARE_GLOBAL_DATA_PTR;
-+
-+static const char *const boot_mode[(CHIP_MODE_M >> CHIP_MODE_S) + 1] = {
-+ [1] = "NAND 2K+64",
-+ [2] = "SPI-NOR 3-Byte Addr",
-+ [3] = "SPI-NOR 4-Byte Addr",
-+ [10] = "NAND 2K+128",
-+ [11] = "NAND 4K+128",
-+ [12] = "NAND 4K+256",
-+};
-+
-+int print_cpuinfo(void)
-+{
-+ void __iomem *sysc = ioremap_nocache(SYSCTL_BASE, SYSCTL_SIZE);
-+ u32 val, ver, eco, pkg, core, dram, chipmode;
-+ u32 cpu_clk, ddr_clk, bus_clk, xtal_clk;
-+ struct udevice *clkdev;
-+ const char *bootdev;
-+ struct clk clk;
-+ int ret;
-+
-+ val = readl(sysc + SYSCTL_CHIP_REV_ID_REG);
-+ ver = FIELD_GET(VER_ID_M, val);
-+ eco = FIELD_GET(ECO_ID_M, val);
-+ pkg = FIELD_GET(PKG_ID, val);
-+ core = FIELD_GET(CPU_ID, val);
-+
-+ val = readl(sysc + SYSCTL_SYSCFG0_REG);
-+ dram = FIELD_GET(DRAM_TYPE, val);
-+ chipmode = FIELD_GET(CHIP_MODE_M, val);
-+
-+ bootdev = boot_mode[chipmode];
-+ if (!bootdev)
-+ bootdev = "Unsupported boot mode";
-+
-+ printf("CPU: MediaTek MT7621%c ver %u, eco %u\n",
-+ core ? (pkg ? 'A' : 'N') : 'S', ver, eco);
-+
-+ printf("Boot: DDR%u, %s\n", dram ? 2 : 3, bootdev);
-+
-+ ret = uclass_get_device_by_driver(UCLASS_CLK, DM_DRIVER_GET(mt7621_clk),
-+ &clkdev);
-+ if (ret)
-+ return ret;
-+
-+ clk.dev = clkdev;
-+
-+ clk.id = MT7621_CLK_CPU;
-+ cpu_clk = clk_get_rate(&clk);
-+
-+ clk.id = MT7621_CLK_BUS;
-+ bus_clk = clk_get_rate(&clk);
-+
-+ clk.id = MT7621_CLK_DDR;
-+ ddr_clk = clk_get_rate(&clk);
-+
-+ clk.id = MT7621_CLK_XTAL;
-+ xtal_clk = clk_get_rate(&clk);
-+
-+ /* Set final timer frequency */
-+ if (cpu_clk)
-+ gd->arch.timer_freq = cpu_clk / 2;
-+
-+ printf("Clock: CPU: %uMHz, DDR: %uMT/s, Bus: %uMHz, XTAL: %uMHz\n",
-+ cpu_clk / 1000000, ddr_clk / 500000, bus_clk / 1000000,
-+ xtal_clk / 1000000);
-+
-+ return 0;
-+}
-+
-+unsigned long get_xtal_mhz(void)
-+{
-+ void __iomem *sysc = ioremap_nocache(SYSCTL_BASE, SYSCTL_SIZE);
-+ u32 bs, xtal_sel;
-+
-+ bs = readl(sysc + SYSCTL_SYSCFG0_REG);
-+ xtal_sel = FIELD_GET(XTAL_MODE_SEL_M, bs);
-+
-+ if (xtal_sel <= 2)
-+ return 20;
-+ else if (xtal_sel <= 5)
-+ return 40;
-+ else
-+ return 25;
-+}
-+
-+static void xhci_config_40mhz(void __iomem *usbh)
-+{
-+ writel(FIELD_PREP(SSUSB_MAC3_SYS_CK_GATE_MASK_TIME_M, 0x20) |
-+ FIELD_PREP(SSUSB_MAC2_SYS_CK_GATE_MASK_TIME_M, 0x20) |
-+ FIELD_PREP(SSUSB_MAC3_SYS_CK_GATE_MODE_M, 2) |
-+ FIELD_PREP(SSUSB_MAC2_SYS_CK_GATE_MODE_M, 2) | 0x10,
-+ usbh + SSUSB_MAC_CK_CTRL_REG);
-+
-+ writel(FIELD_PREP(SSUSB_PLL_PREDIV_PE1D_M, 2) |
-+ FIELD_PREP(SSUSB_PLL_PREDIV_U3_M, 1) |
-+ FIELD_PREP(SSUSB_PLL_FBKDI_M, 4),
-+ usbh + DA_SSUSB_U3PHYA_10_REG);
-+
-+ writel(FIELD_PREP(SSUSB_PLL_FBKDIV_PE2H_M, 0x18) |
-+ FIELD_PREP(SSUSB_PLL_FBKDIV_PE1D_M, 0x18) |
-+ FIELD_PREP(SSUSB_PLL_FBKDIV_PE1H_M, 0x18) |
-+ FIELD_PREP(SSUSB_PLL_FBKDIV_U3_M, 0x1e),
-+ usbh + DA_SSUSB_PLL_FBKDIV_REG);
-+
-+ writel(FIELD_PREP(SSUSB_PLL_PCW_NCPO_U3_M, 0x1e400000),
-+ usbh + DA_SSUSB_PLL_PCW_NCPO_REG);
-+
-+ writel(FIELD_PREP(SSUSB_PLL_SSC_DELTA1_PE1H_M, 0x25) |
-+ FIELD_PREP(SSUSB_PLL_SSC_DELTA1_U3_M, 0x73),
-+ usbh + DA_SSUSB_PLL_SSC_DELTA1_REG);
-+
-+ writel(FIELD_PREP(SSUSB_PLL_SSC_DELTA_U3_M, 0x71) |
-+ FIELD_PREP(SSUSB_PLL_SSC_DELTA1_PE2D_M, 0x4a),
-+ usbh + DA_SSUSB_U3PHYA_21_REG);
-+
-+ writel(FIELD_PREP(SSUSB_PLL_SSC_PRD_M, 0x140),
-+ usbh + SSUSB_U3PHYA_9_REG);
-+
-+ writel(FIELD_PREP(SSUSB_SYSPLL_PCW_NCPO_M, 0x11c00000),
-+ usbh + SSUSB_U3PHYA_3_REG);
-+
-+ writel(FIELD_PREP(SSUSB_PCIE_CLKDRV_AMP_M, 4) |
-+ FIELD_PREP(SSUSB_SYSPLL_FBSEL_M, 1) |
-+ FIELD_PREP(SSUSB_SYSPLL_PREDIV_M, 1),
-+ usbh + SSUSB_U3PHYA_1_REG);
-+
-+ writel(FIELD_PREP(SSUSB_SYSPLL_FBDIV_M, 0x12) |
-+ SSUSB_SYSPLL_VCO_DIV_SEL | SSUSB_SYSPLL_FPEN |
-+ SSUSB_SYSPLL_MONCK_EN | SSUSB_SYSPLL_VOD_EN,
-+ usbh + SSUSB_U3PHYA_2_REG);
-+
-+ writel(SSUSB_EQ_CURSEL | FIELD_PREP(SSUSB_RX_DAC_MUX_M, 8) |
-+ FIELD_PREP(SSUSB_PCIE_SIGDET_VTH_M, 1) |
-+ FIELD_PREP(SSUSB_PCIE_SIGDET_LPF_M, 1),
-+ usbh + SSUSB_U3PHYA_11_REG);
-+
-+ writel(FIELD_PREP(SSUSB_RING_OSC_CNTEND_M, 0x1ff) |
-+ FIELD_PREP(SSUSB_XTAL_OSC_CNTEND_M, 0x7f) |
-+ SSUSB_RING_BYPASS_DET,
-+ usbh + SSUSB_B2_ROSC_0_REG);
-+
-+ writel(FIELD_PREP(SSUSB_RING_OSC_FRC_RECAL_M, 3) |
-+ SSUSB_RING_OSC_FRC_SEL,
-+ usbh + SSUSB_B2_ROSC_1_REG);
-+}
-+
-+static void xhci_config_25mhz(void __iomem *usbh)
-+{
-+ writel(FIELD_PREP(SSUSB_MAC3_SYS_CK_GATE_MASK_TIME_M, 0x20) |
-+ FIELD_PREP(SSUSB_MAC2_SYS_CK_GATE_MASK_TIME_M, 0x20) |
-+ FIELD_PREP(SSUSB_MAC3_SYS_CK_GATE_MODE_M, 2) |
-+ FIELD_PREP(SSUSB_MAC2_SYS_CK_GATE_MODE_M, 2) | 0x10,
-+ usbh + SSUSB_MAC_CK_CTRL_REG);
-+
-+ writel(FIELD_PREP(SSUSB_PLL_PREDIV_PE1D_M, 2) |
-+ FIELD_PREP(SSUSB_PLL_FBKDI_M, 4),
-+ usbh + DA_SSUSB_U3PHYA_10_REG);
-+
-+ writel(FIELD_PREP(SSUSB_PLL_FBKDIV_PE2H_M, 0x18) |
-+ FIELD_PREP(SSUSB_PLL_FBKDIV_PE1D_M, 0x18) |
-+ FIELD_PREP(SSUSB_PLL_FBKDIV_PE1H_M, 0x18) |
-+ FIELD_PREP(SSUSB_PLL_FBKDIV_U3_M, 0x19),
-+ usbh + DA_SSUSB_PLL_FBKDIV_REG);
-+
-+ writel(FIELD_PREP(SSUSB_PLL_PCW_NCPO_U3_M, 0x18000000),
-+ usbh + DA_SSUSB_PLL_PCW_NCPO_REG);
-+
-+ writel(FIELD_PREP(SSUSB_PLL_SSC_DELTA1_PE1H_M, 0x25) |
-+ FIELD_PREP(SSUSB_PLL_SSC_DELTA1_U3_M, 0x4a),
-+ usbh + DA_SSUSB_PLL_SSC_DELTA1_REG);
-+
-+ writel(FIELD_PREP(SSUSB_PLL_SSC_DELTA_U3_M, 0x48) |
-+ FIELD_PREP(SSUSB_PLL_SSC_DELTA1_PE2D_M, 0x4a),
-+ usbh + DA_SSUSB_U3PHYA_21_REG);
-+
-+ writel(FIELD_PREP(SSUSB_PLL_SSC_PRD_M, 0x190),
-+ usbh + SSUSB_U3PHYA_9_REG);
-+
-+ writel(FIELD_PREP(SSUSB_SYSPLL_PCW_NCPO_M, 0xe000000),
-+ usbh + SSUSB_U3PHYA_3_REG);
-+
-+ writel(FIELD_PREP(SSUSB_PCIE_CLKDRV_AMP_M, 4) |
-+ FIELD_PREP(SSUSB_SYSPLL_FBSEL_M, 1),
-+ usbh + SSUSB_U3PHYA_1_REG);
-+
-+ writel(FIELD_PREP(SSUSB_SYSPLL_FBDIV_M, 0xf) |
-+ SSUSB_SYSPLL_VCO_DIV_SEL | SSUSB_SYSPLL_FPEN |
-+ SSUSB_SYSPLL_MONCK_EN | SSUSB_SYSPLL_VOD_EN,
-+ usbh + SSUSB_U3PHYA_2_REG);
-+
-+ writel(SSUSB_EQ_CURSEL | FIELD_PREP(SSUSB_RX_DAC_MUX_M, 8) |
-+ FIELD_PREP(SSUSB_PCIE_SIGDET_VTH_M, 1) |
-+ FIELD_PREP(SSUSB_PCIE_SIGDET_LPF_M, 1),
-+ usbh + SSUSB_U3PHYA_11_REG);
-+
-+ writel(FIELD_PREP(SSUSB_RING_OSC_CNTEND_M, 0x1ff) |
-+ FIELD_PREP(SSUSB_XTAL_OSC_CNTEND_M, 0x7f) |
-+ SSUSB_RING_BYPASS_DET,
-+ usbh + SSUSB_B2_ROSC_0_REG);
-+
-+ writel(FIELD_PREP(SSUSB_RING_OSC_FRC_RECAL_M, 3) |
-+ SSUSB_RING_OSC_FRC_SEL,
-+ usbh + SSUSB_B2_ROSC_1_REG);
-+}
-+
-+void lowlevel_init(void)
-+{
-+ void __iomem *usbh = ioremap_nocache(SSUSB_BASE, SSUSB_SIZE);
-+ u32 xtal = get_xtal_mhz();
-+
-+ /* Setup USB xHCI */
-+ if (xtal == 40)
-+ xhci_config_40mhz(usbh);
-+ else if (xtal == 25)
-+ xhci_config_25mhz(usbh);
-+}
-+
-+ulong notrace get_tbclk(void)
-+{
-+ return gd->arch.timer_freq;
-+}
-+
-+void _machine_restart(void)
-+{
-+ void __iomem *sysc = ioremap_nocache(SYSCTL_BASE, SYSCTL_SIZE);
-+
-+ while (1)
-+ writel(SYS_RST, sysc + SYSCTL_RSTCTL_REG);
-+}
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/mt7621.h
-@@ -0,0 +1,229 @@
-+/* SPDX-License-Identifier: GPL-2.0 */
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#ifndef _MT7621_H_
-+#define _MT7621_H_
-+
-+#define SYSCTL_BASE 0x1e000000
-+#define SYSCTL_SIZE 0x100
-+#define TIMER_BASE 0x1e000100
-+#define TIMER_SIZE 0x100
-+#define RBUS_BASE 0x1e000400
-+#define RBUS_SIZE 0x100
-+#define GPIO_BASE 0x1e000600
-+#define GPIO_SIZE 0x100
-+#define DMA_CFG_ARB_BASE 0x1e000800
-+#define DMA_CFG_ARB_SIZE 0x100
-+#define SPI_BASE 0x1e000b00
-+#define SPI_SIZE 0x100
-+#define UART1_BASE 0x1e000c00
-+#define UART1_SIZE 0x100
-+#define UART2_BASE 0x1e000d00
-+#define UART2_SIZE 0x100
-+#define UART3_BASE 0x1e000e00
-+#define UART3_SIZE 0x100
-+#define NFI_BASE 0x1e003000
-+#define NFI_SIZE 0x800
-+#define NFI_ECC_BASE 0x1e003800
-+#define NFI_ECC_SIZE 0x800
-+#define DRAMC_BASE 0x1e005000
-+#define DRAMC_SIZE 0x1000
-+#define FE_BASE 0x1e100000
-+#define FE_SIZE 0xe000
-+#define GMAC_BASE 0x1e110000
-+#define GMAC_SIZE 0x8000
-+#define SSUSB_BASE 0x1e1c0000
-+#define SSUSB_SIZE 0x40000
-+
-+ /* GIC Base Address */
-+#define MIPS_GIC_BASE 0x1fbc0000
-+
-+ /* CPC Base Address */
-+#define MIPS_CPC_BASE 0x1fbf0000
-+
-+ /* Flash Memory-mapped Base Address */
-+#define FLASH_MMAP_BASE 0x1fc00000
-+#define TPL_INFO_OFFSET 0x40
-+#define TPL_INFO_MAGIC 0x31323637 /* Magic "7621" */
-+
-+/* SRAM */
-+#define FE_SRAM_BASE1 0x8000
-+#define FE_SRAM_BASE2 0xa000
-+
-+/* SYSCTL_BASE */
-+#define SYSCTL_CHIP_REV_ID_REG 0x0c
-+#define CPU_ID 0x20000
-+#define PKG_ID 0x10000
-+#define VER_ID_S 8
-+#define VER_ID_M 0xf00
-+#define ECO_ID_S 0
-+#define ECO_ID_M 0x0f
-+
-+#define SYSCTL_SYSCFG0_REG 0x10
-+#define XTAL_MODE_SEL_S 6
-+#define XTAL_MODE_SEL_M 0x1c0
-+#define DRAM_TYPE 0x10
-+#define CHIP_MODE_S 0
-+#define CHIP_MODE_M 0x0f
-+
-+#define BOOT_SRAM_BASE_REG 0x20
-+
-+#define SYSCTL_CLKCFG0_REG 0x2c
-+#define CPU_CLK_SEL_S 30
-+#define CPU_CLK_SEL_M 0xc0000000
-+#define MPLL_CFG_SEL_S 23
-+#define MPLL_CFG_SEL_M 0x800000
-+
-+#define SYSCTL_RSTCTL_REG 0x34
-+#define MCM_RST 0x04
-+#define SYS_RST 0x01
-+
-+#define SYSCTL_CUR_CLK_STS_REG 0x44
-+#define CUR_CPU_FDIV_S 8
-+#define CUR_CPU_FDIV_M 0x1f00
-+#define CUR_CPU_FFRAC_S 0
-+#define CUR_CPU_FFRAC_M 0x1f
-+
-+#define SYSCTL_GPIOMODE_REG 0x60
-+#define UART2_MODE_S 5
-+#define UART2_MODE_M 0x60
-+#define UART3_MODE_S 3
-+#define UART3_MODE_M 0x18
-+#define UART1_MODE 0x02
-+
-+/* RBUS_BASE */
-+#define RBUS_DYN_CFG0_REG 0x0010
-+#define CPU_FDIV_S 8
-+#define CPU_FDIV_M 0x1f00
-+#define CPU_FFRAC_S 0
-+#define CPU_FFRAC_M 0x1f
-+
-+/* DMA_CFG_ARB_BASE */
-+#define DMA_ROUTE_REG 0x000c
-+
-+/* SPI_BASE */
-+#define SPI_SPACE_REG 0x003c
-+#define FS_SLAVE_SEL_S 12
-+#define FS_SLAVE_SEL_M 0x70000
-+#define FS_CLK_SEL_S 0
-+#define FS_CLK_SEL_M 0xfff
-+
-+/* FE_BASE */
-+#define FE_RST_GLO_REG 0x0004
-+#define FE_PSE_RAM 0x04
-+#define FE_PSE_MEM_EN 0x02
-+#define FE_PSE_RESET 0x01
-+
-+/* SSUSB_BASE */
-+#define SSUSB_MAC_CK_CTRL_REG 0x10784
-+#define SSUSB_MAC3_SYS_CK_GATE_MASK_TIME_S 16
-+#define SSUSB_MAC3_SYS_CK_GATE_MASK_TIME_M 0xff0000
-+#define SSUSB_MAC2_SYS_CK_GATE_MASK_TIME_S 8
-+#define SSUSB_MAC2_SYS_CK_GATE_MASK_TIME_M 0xff00
-+#define SSUSB_MAC3_SYS_CK_GATE_MODE_S 2
-+#define SSUSB_MAC3_SYS_CK_GATE_MODE_M 0x0c
-+#define SSUSB_MAC2_SYS_CK_GATE_MODE_S 0
-+#define SSUSB_MAC2_SYS_CK_GATE_MODE_M 0x03
-+
-+#define SSUSB_B2_ROSC_0_REG 0x10a40
-+#define SSUSB_RING_OSC_CNTEND_S 23
-+#define SSUSB_RING_OSC_CNTEND_M 0xff800000
-+#define SSUSB_XTAL_OSC_CNTEND_S 16
-+#define SSUSB_XTAL_OSC_CNTEND_M 0x7f0000
-+#define SSUSB_RING_BYPASS_DET 0x01
-+
-+#define SSUSB_B2_ROSC_1_REG 0x10a44
-+#define SSUSB_RING_OSC_FRC_RECAL_S 17
-+#define SSUSB_RING_OSC_FRC_RECAL_M 0x60000
-+#define SSUSB_RING_OSC_FRC_SEL 0x01
-+
-+#define SSUSB_U3PHYA_1_REG 0x10b04
-+#define SSUSB_PCIE_CLKDRV_AMP_S 27
-+#define SSUSB_PCIE_CLKDRV_AMP_M 0x38000000
-+#define SSUSB_SYSPLL_FBSEL_S 2
-+#define SSUSB_SYSPLL_FBSEL_M 0x0c
-+#define SSUSB_SYSPLL_PREDIV_S 0
-+#define SSUSB_SYSPLL_PREDIV_M 0x03
-+
-+#define SSUSB_U3PHYA_2_REG 0x10b08
-+#define SSUSB_SYSPLL_FBDIV_S 24
-+#define SSUSB_SYSPLL_FBDIV_M 0x7f000000
-+#define SSUSB_SYSPLL_VCO_DIV_SEL 0x200000
-+#define SSUSB_SYSPLL_FPEN 0x2000
-+#define SSUSB_SYSPLL_MONCK_EN 0x1000
-+#define SSUSB_SYSPLL_VOD_EN 0x200
-+
-+#define SSUSB_U3PHYA_3_REG 0x10b10
-+#define SSUSB_SYSPLL_PCW_NCPO_S 1
-+#define SSUSB_SYSPLL_PCW_NCPO_M 0xfffffffe
-+
-+#define SSUSB_U3PHYA_9_REG 0x10b24
-+#define SSUSB_PLL_SSC_PRD_S 0
-+#define SSUSB_PLL_SSC_PRD_M 0xffff
-+
-+#define SSUSB_U3PHYA_11_REG 0x10b2c
-+#define SSUSB_EQ_CURSEL 0x1000000
-+#define SSUSB_RX_DAC_MUX_S 19
-+#define SSUSB_RX_DAC_MUX_M 0xf80000
-+#define SSUSB_PCIE_SIGDET_VTH_S 5
-+#define SSUSB_PCIE_SIGDET_VTH_M 0x60
-+#define SSUSB_PCIE_SIGDET_LPF_S 3
-+#define SSUSB_PCIE_SIGDET_LPF_M 0x18
-+
-+#define DA_SSUSB_PLL_FBKDIV_REG 0x10c1c
-+#define SSUSB_PLL_FBKDIV_PE2H_S 24
-+#define SSUSB_PLL_FBKDIV_PE2H_M 0x7f000000
-+#define SSUSB_PLL_FBKDIV_PE1D_S 16
-+#define SSUSB_PLL_FBKDIV_PE1D_M 0x7f0000
-+#define SSUSB_PLL_FBKDIV_PE1H_S 8
-+#define SSUSB_PLL_FBKDIV_PE1H_M 0x7f00
-+#define SSUSB_PLL_FBKDIV_U3_S 0
-+#define SSUSB_PLL_FBKDIV_U3_M 0x7f
-+
-+#define DA_SSUSB_U3PHYA_10_REG 0x10c20
-+#define SSUSB_PLL_PREDIV_PE1D_S 18
-+#define SSUSB_PLL_PREDIV_PE1D_M 0xc0000
-+#define SSUSB_PLL_PREDIV_U3_S 8
-+#define SSUSB_PLL_PREDIV_U3_M 0x300
-+#define SSUSB_PLL_FBKDI_S 0
-+#define SSUSB_PLL_FBKDI_M 0x07
-+
-+#define DA_SSUSB_PLL_PCW_NCPO_REG 0x10c24
-+#define SSUSB_PLL_PCW_NCPO_U3_S 0
-+#define SSUSB_PLL_PCW_NCPO_U3_M 0x7fffffff
-+
-+#define DA_SSUSB_PLL_SSC_DELTA1_REG 0x10c38
-+#define SSUSB_PLL_SSC_DELTA1_PE1H_S 16
-+#define SSUSB_PLL_SSC_DELTA1_PE1H_M 0xffff0000
-+#define SSUSB_PLL_SSC_DELTA1_U3_S 0
-+#define SSUSB_PLL_SSC_DELTA1_U3_M 0xffff
-+
-+#define DA_SSUSB_U3PHYA_21_REG 0x10c40
-+#define SSUSB_PLL_SSC_DELTA_U3_S 16
-+#define SSUSB_PLL_SSC_DELTA_U3_M 0xffff0000
-+#define SSUSB_PLL_SSC_DELTA1_PE2D_S 0
-+#define SSUSB_PLL_SSC_DELTA1_PE2D_M 0xffff
-+
-+/* MT7621 specific CM values */
-+
-+/* GCR_REGx_BASE */
-+#define GCR_REG0_BASE_VALUE 0x1c000000
-+#define GCR_REG1_BASE_VALUE 0x60000000
-+#define GCR_REG2_BASE_VALUE 0x1c000000
-+#define GCR_REG3_BASE_VALUE 0x1c000000
-+
-+/* GCR_REGx_MASK */
-+#define GCR_REG0_MASK_VALUE 0x0000fc00 /* 64M Bus */
-+#define GCR_REG1_MASK_VALUE 0x0000f000 /* 256M PCI Mem */
-+#define GCR_REG2_MASK_VALUE 0x0000fc00 /* unused */
-+#define GCR_REG3_MASK_VALUE 0x0000fc00 /* unused */
-+
-+#ifndef __ASSEMBLY__
-+unsigned long get_xtal_mhz(void);
-+#endif
-+
-+#endif /* _MT7621_H_ */
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/serial.c
-@@ -0,0 +1,23 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <asm/io.h>
-+#include <asm/addrspace.h>
-+#include "mt7621.h"
-+
-+void board_debug_uart_init(void)
-+{
-+ void __iomem *base = ioremap_nocache(SYSCTL_BASE, SYSCTL_SIZE);
-+
-+#if CONFIG_DEBUG_UART_BASE == 0xbe000c00 /* KSEG1ADDR(UART1_BASE) */
-+ clrbits_32(base + SYSCTL_GPIOMODE_REG, UART1_MODE);
-+#elif CONFIG_DEBUG_UART_BASE == 0xbe000d00 /* KSEG1ADDR(UART2_BASE) */
-+ clrbits_32(base + SYSCTL_GPIOMODE_REG, UART2_MODE_M);
-+#elif CONFIG_DEBUG_UART_BASE == 0xbe000e00 /* KSEG1ADDR(UART3_BASE) */
-+ clrbits_32(base + SYSCTL_GPIOMODE_REG, UART3_MODE_M);
-+#endif
-+}
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/spl/Makefile
-@@ -0,0 +1,9 @@
-+
-+extra-y += start.o
-+
-+obj-y += spl.o
-+obj-y += cps.o
-+obj-y += dram.o
-+obj-y += serial.o
-+obj-y += launch.o
-+obj-y += launch_ll.o
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/spl/cps.c
-@@ -0,0 +1,153 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <asm/io.h>
-+#include <asm/addrspace.h>
-+#include <asm/mipsregs.h>
-+#include <asm/cm.h>
-+#include <linux/bitfield.h>
-+#include "../mt7621.h"
-+
-+/* GIC Shared Register Bases */
-+#define GIC_SH_POL_BASE 0x100
-+#define GIC_SH_TRIG_BASE 0x180
-+#define GIC_SH_RMASK_BASE 0x300
-+#define GIC_SH_SMASK_BASE 0x380
-+#define GIC_SH_MASK_BASE 0x400
-+#define GIC_SH_PEND_BASE 0x480
-+#define GIC_SH_MAP_PIN_BASE 0x500
-+#define GIC_SH_MAP_VPE_BASE 0x2000
-+
-+/* GIC Registers */
-+#define GIC_SH_POL31_0 (GIC_SH_POL_BASE + 0x00)
-+#define GIC_SH_POL63_32 (GIC_SH_POL_BASE + 0x04)
-+
-+#define GIC_SH_TRIG31_0 (GIC_SH_TRIG_BASE + 0x00)
-+#define GIC_SH_TRIG63_32 (GIC_SH_TRIG_BASE + 0x04)
-+
-+#define GIC_SH_RMASK31_0 (GIC_SH_RMASK_BASE + 0x00)
-+#define GIC_SH_RMASK63_32 (GIC_SH_RMASK_BASE + 0x04)
-+
-+#define GIC_SH_SMASK31_0 (GIC_SH_SMASK_BASE + 0x00)
-+#define GIC_SH_SMASK63_32 (GIC_SH_SMASK_BASE + 0x04)
-+
-+#define GIC_SH_MAP_PIN(n) (GIC_SH_MAP_PIN_BASE + (n) * 4)
-+
-+#define GIC_SH_MAP_VPE(n, v) (GIC_SH_MAP_VPE_BASE + (n) * 0x20 + ((v) / 32) * 4)
-+#define GIC_SH_MAP_VPE31_0(n) GIC_SH_MAP_VPE(n, 0)
-+
-+/* GIC_SH_MAP_PIN fields */
-+#define GIC_MAP_TO_PIN BIT(31)
-+#define GIC_MAP_TO_NMI BIT(30)
-+#define GIC_MAP GENMASK(5, 0)
-+#define GIC_MAP_SHIFT 0
-+
-+static void cm_init(void __iomem *cm_base)
-+{
-+ u32 gcrcfg, num_cores;
-+
-+ gcrcfg = readl(cm_base + GCR_CONFIG);
-+ num_cores = FIELD_GET(GCR_CONFIG_PCORES, gcrcfg) + 1;
-+
-+ writel((1 << num_cores) - 1, cm_base + GCR_ACCESS);
-+
-+ writel(GCR_REG0_BASE_VALUE, cm_base + GCR_REG0_BASE);
-+ writel(GCR_REG1_BASE_VALUE, cm_base + GCR_REG1_BASE);
-+ writel(GCR_REG2_BASE_VALUE, cm_base + GCR_REG2_BASE);
-+ writel(GCR_REG3_BASE_VALUE, cm_base + GCR_REG3_BASE);
-+
-+ clrsetbits_32(cm_base + GCR_REG0_MASK,
-+ GCR_REGn_MASK_ADDRMASK | GCR_REGn_MASK_CMTGT,
-+ FIELD_PREP(GCR_REGn_MASK_ADDRMASK, GCR_REG0_MASK_VALUE) |
-+ GCR_REGn_MASK_CMTGT_IOCU0);
-+
-+ clrsetbits_32(cm_base + GCR_REG1_MASK,
-+ GCR_REGn_MASK_ADDRMASK | GCR_REGn_MASK_CMTGT,
-+ FIELD_PREP(GCR_REGn_MASK_ADDRMASK, GCR_REG1_MASK_VALUE) |
-+ GCR_REGn_MASK_CMTGT_IOCU0);
-+
-+ clrsetbits_32(cm_base + GCR_REG2_MASK,
-+ GCR_REGn_MASK_ADDRMASK | GCR_REGn_MASK_CMTGT,
-+ FIELD_PREP(GCR_REGn_MASK_ADDRMASK, GCR_REG2_MASK_VALUE) |
-+ GCR_REGn_MASK_CMTGT_IOCU0);
-+
-+ clrsetbits_32(cm_base + GCR_REG3_MASK,
-+ GCR_REGn_MASK_ADDRMASK | GCR_REGn_MASK_CMTGT,
-+ FIELD_PREP(GCR_REGn_MASK_ADDRMASK, GCR_REG3_MASK_VALUE) |
-+ GCR_REGn_MASK_CMTGT_IOCU0);
-+
-+ clrbits_32(cm_base + GCR_BASE, CM_DEFAULT_TARGET_MASK);
-+ setbits_32(cm_base + GCR_CONTROL, GCR_CONTROL_SYNCCTL);
-+}
-+
-+static void gic_init(void)
-+{
-+ void __iomem *gic_base = (void *)KSEG1ADDR(MIPS_GIC_BASE);
-+ int i;
-+
-+ /* Interrupt 0..5: Level Trigger, Active High */
-+ writel(0, gic_base + GIC_SH_TRIG31_0);
-+ writel(0x3f, gic_base + GIC_SH_RMASK31_0);
-+ writel(0x3f, gic_base + GIC_SH_POL31_0);
-+ writel(0x3f, gic_base + GIC_SH_SMASK31_0);
-+
-+ /* Interrupt 56..63: Edge Trigger, Rising Edge */
-+ /* Hardcoded to set up the last 8 external interrupts for IPI. */
-+ writel(0xff000000, gic_base + GIC_SH_TRIG63_32);
-+ writel(0xff000000, gic_base + GIC_SH_RMASK63_32);
-+ writel(0xff000000, gic_base + GIC_SH_POL63_32);
-+ writel(0xff000000, gic_base + GIC_SH_SMASK63_32);
-+
-+ /* Map interrupt source to particular hardware interrupt pin */
-+ /* source {0,1,2,3,4,5} -> pin {0,0,4,3,0,5} */
-+ writel(GIC_MAP_TO_PIN | 0, gic_base + GIC_SH_MAP_PIN(0));
-+ writel(GIC_MAP_TO_PIN | 0, gic_base + GIC_SH_MAP_PIN(1));
-+ writel(GIC_MAP_TO_PIN | 4, gic_base + GIC_SH_MAP_PIN(2));
-+ writel(GIC_MAP_TO_PIN | 3, gic_base + GIC_SH_MAP_PIN(3));
-+ writel(GIC_MAP_TO_PIN | 0, gic_base + GIC_SH_MAP_PIN(4));
-+ writel(GIC_MAP_TO_PIN | 5, gic_base + GIC_SH_MAP_PIN(5));
-+
-+ /* source 56~59 -> pin 1, 60~63 -> pin 2 */
-+ writel(GIC_MAP_TO_PIN | 1, gic_base + GIC_SH_MAP_PIN(56));
-+ writel(GIC_MAP_TO_PIN | 1, gic_base + GIC_SH_MAP_PIN(57));
-+ writel(GIC_MAP_TO_PIN | 1, gic_base + GIC_SH_MAP_PIN(58));
-+ writel(GIC_MAP_TO_PIN | 1, gic_base + GIC_SH_MAP_PIN(59));
-+ writel(GIC_MAP_TO_PIN | 2, gic_base + GIC_SH_MAP_PIN(60));
-+ writel(GIC_MAP_TO_PIN | 2, gic_base + GIC_SH_MAP_PIN(61));
-+ writel(GIC_MAP_TO_PIN | 2, gic_base + GIC_SH_MAP_PIN(62));
-+ writel(GIC_MAP_TO_PIN | 2, gic_base + GIC_SH_MAP_PIN(63));
-+
-+ /* Interrupt map to VPE (bit mask) */
-+ for (i = 0; i < 32; i++)
-+ writel(BIT(0), gic_base + GIC_SH_MAP_VPE31_0(i));
-+
-+ /*
-+ * Direct GIC_int 56..63 to vpe 0..3
-+ * MIPS Linux convention that last 16 interrupts implemented be set
-+ * aside for IPI signaling.
-+ * The actual interrupts are tied low and software sends interrupts
-+ * via GIC_SH_WEDGE writes.
-+ */
-+ for (i = 0; i < 4; i++) {
-+ writel(BIT(i), gic_base + GIC_SH_MAP_VPE31_0(i + 56));
-+ writel(BIT(i), gic_base + GIC_SH_MAP_VPE31_0(i + 60));
-+ }
-+}
-+
-+void mt7621_cps_init(void)
-+{
-+ void __iomem *cm_base = (void *)KSEG1ADDR(CONFIG_MIPS_CM_BASE);
-+
-+ /* Enable GIC */
-+ writel(MIPS_GIC_BASE | GCR_GIC_EN, cm_base + GCR_GIC_BASE);
-+
-+ /* Enable CPC */
-+ writel(MIPS_CPC_BASE | GCR_CPC_EN, cm_base + GCR_CPC_BASE);
-+
-+ gic_init();
-+ cm_init(cm_base);
-+}
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/spl/dram.c
-@@ -0,0 +1,153 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <vsprintf.h>
-+#include <asm/io.h>
-+#include <asm/sections.h>
-+#include <asm/byteorder.h>
-+#include <asm/addrspace.h>
-+#include <linux/string.h>
-+#include "../mt7621.h"
-+#include "dram.h"
-+
-+static const u32 ddr2_act[DDR_PARAM_SIZE] = {
-+#if defined(CONFIG_MT7621_DRAM_DDR2_512M)
-+ 0xAA00AA00, 0xAA00AA00, 0x00000007, 0x22174441,
-+ 0x00000000, 0xF0748661, 0x40001273, 0x9F0A0481,
-+ 0x0304692F, 0x15602842, 0x00008888, 0x88888888,
-+ 0x00000000, 0x00000000, 0x00000000, 0x07100000,
-+ 0x00001B63, 0x00002000, 0x00004000, 0x00006000,
-+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
-+#elif defined(CONFIG_MT7621_DRAM_DDR2_512M_W9751G6KB_A02_1066MHZ)
-+ 0xAA00AA00, 0xAA00AA00, 0x00000007, 0x33484584,
-+ 0x00000000, 0xF07486A1, 0x50001273, 0x9F010481,
-+ 0x0304693F, 0x15602842, 0x00008888, 0x88888888,
-+ 0x00000000, 0x00000000, 0x00000010, 0x07100000,
-+ 0x00001F73, 0x00002000, 0x00004000, 0x00006000,
-+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
-+#elif defined(CONFIG_MT7621_DRAM_DDR2_1024M_W971GG6KB25_800MHZ)
-+ 0xAA00AA00, 0xAA00AA00, 0x00000007, 0x22174430,
-+ 0x01000000, 0xF0748661, 0x40001273, 0x9F0F0481,
-+ 0x0304692F, 0x15602842, 0x00008888, 0x88888888,
-+ 0x00000000, 0x00000000, 0x00000000, 0x07100000,
-+ 0x00001B63, 0x00002000, 0x00004000, 0x00006000,
-+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
-+#elif defined(CONFIG_MT7621_DRAM_DDR2_1024M_W971GG6KB18_1066MHZ)
-+ 0xAA00AA00, 0xAA00AA00, 0x00000007, 0x33484584,
-+ 0x01000000, 0xF07486A1, 0x50001273, 0x9F070481,
-+ 0x0304693F, 0x15602842, 0x00008888, 0x88888888,
-+ 0x00000000, 0x00000000, 0x00000010, 0x07100000,
-+ 0x00001F73, 0x00002000, 0x00004000, 0x00006000,
-+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
-+#else /* CONFIG_MT7621_DRAM_DDR2_1024M */
-+ 0xAA00AA00, 0xAA00AA00, 0x00000007, 0x22174441,
-+ 0x01000000, 0xF0748661, 0x40001273, 0x9F0F0481,
-+ 0x0304692F, 0x15602842, 0x00008888, 0x88888888,
-+ 0x00000000, 0x00000000, 0x00000000, 0x07100000,
-+ 0x00001B63, 0x00002000, 0x00004000, 0x00006000,
-+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
-+#endif
-+};
-+
-+static const u32 ddr3_act[DDR_PARAM_SIZE] = {
-+#if defined(CONFIG_MT7621_DRAM_DDR3_1024M)
-+ 0xAA00AA00, 0xAA00AA00, 0x00000007, 0x44694683,
-+ 0x01000000, 0xF07486A1, 0xC287221D, 0x9F060481,
-+ 0x03046948, 0x15602842, 0x00008888, 0x88888888,
-+ 0x00000000, 0x00000000, 0x00000210, 0x07100000,
-+ 0x00001B61, 0x00002040, 0x00004010, 0x00006000,
-+ 0x0C000000, 0x07070000, 0x00000000, 0x00000000,
-+#elif defined(CONFIG_MT7621_DRAM_DDR3_4096M)
-+ 0xAA00AA00, 0xAA00AA00, 0x00000007, 0x44694683,
-+ 0x01000000, 0xF07486A1, 0xC287221D, 0x9F0F0481,
-+ 0x03046948, 0x15602842, 0x00008888, 0x88888888,
-+ 0x00000000, 0x00000000, 0x00000240, 0x07100000,
-+ 0x00001B61, 0x00002040, 0x00004010, 0x00006000,
-+ 0x0C000000, 0x07070000, 0x00000000, 0x00000000,
-+#elif defined(CONFIG_MT7621_DRAM_DDR3_1024M_KGD)
-+ 0xFF00FF00, 0xFF00FF00, 0x00000007, 0x44694683,
-+ 0x01000000, 0xF07406A1, 0xC287221D, 0x9F060481,
-+ 0x03046923, 0x152f2842, 0x00008888, 0x88888888,
-+ 0x00000000, 0x00000000, 0x00000210, 0x07100000,
-+ 0x00001B61, 0x00002040, 0x00004010, 0x00006000,
-+ 0x0C000000, 0x07070000, 0x000C0000, 0x00000000,
-+#else /* CONFIG_MT7621_DRAM_DDR3_2048M */
-+ 0xAA00AA00, 0xAA00AA00, 0x00000007, 0x44694673,
-+ 0x01000000, 0xF07486A1, 0xC287221D, 0x9F050481,
-+ 0x03046948, 0x15602842, 0x00008888, 0x88888888,
-+ 0x00000000, 0x00000000, 0x00000220, 0x07100000,
-+ 0x00001B61, 0x00002040, 0x00004010, 0x00006000,
-+ 0x0C000000, 0x07070000, 0x00000000, 0x00000000,
-+#endif
-+};
-+
-+#if defined(CONFIG_MT7621_DRAM_FREQ_400)
-+#define DDR_FREQ_PARAM 0x41000000
-+#elif defined(CONFIG_MT7621_DRAM_FREQ_1066)
-+#define DDR_FREQ_PARAM 0x21000000
-+#elif defined(CONFIG_MT7621_DRAM_FREQ_1200)
-+#define DDR_FREQ_PARAM 0x11000000
-+#else /* CONFIG_MT7621_DRAM_FREQ_800 */
-+#define DDR_FREQ_PARAM 0x31000000
-+#endif
-+
-+#define RG_MEPL_FBDIV_S 4
-+#define RG_MEPL_FBDIV_M 0x7f
-+
-+static inline void word_copy(u32 *dest, const u32 *src, u32 count)
-+{
-+ u32 i;
-+
-+ for (i = 0; i < count; i++)
-+ dest[i] = src[i];
-+}
-+
-+static u32 calc_cpu_pll_val(void)
-+{
-+ u32 div, baseval, fb;
-+
-+ div = get_xtal_mhz();
-+
-+ if (div == 40) {
-+ div /= 2;
-+ baseval = 0xc0005802;
-+ } else {
-+ baseval = 0xc0004802;
-+ }
-+
-+ fb = CONFIG_MT7621_CPU_FREQ / div - 1;
-+ if (fb > RG_MEPL_FBDIV_M)
-+ fb = RG_MEPL_FBDIV_M;
-+
-+ return baseval | (fb << RG_MEPL_FBDIV_S);
-+}
-+
-+void prepare_stage_bin(void)
-+{
-+ u32 stage_size;
-+
-+ const struct stage_header *stock_stage_bin =
-+ (const struct stage_header *)__image_copy_end;
-+
-+ struct stage_header *new_stage_bin =
-+ (struct stage_header *)STAGE_LOAD_ADDR;
-+
-+ if (be32_to_cpu(stock_stage_bin->ep) != STAGE_LOAD_ADDR)
-+ panic("Invalid DDR stage binary blob\n");
-+
-+ stage_size = be32_to_cpu(stock_stage_bin->stage_size);
-+
-+ word_copy((u32 *)new_stage_bin, (const u32 *)stock_stage_bin,
-+ (stage_size + sizeof(u32) - 1) / sizeof(u32));
-+
-+ word_copy(new_stage_bin->ddr2_act, ddr2_act, DDR_PARAM_SIZE);
-+ word_copy(new_stage_bin->ddr3_act, ddr3_act, DDR_PARAM_SIZE);
-+
-+ new_stage_bin->cpu_pll_cfg = calc_cpu_pll_val();
-+ new_stage_bin->ddr_pll_cfg = DDR_FREQ_PARAM;
-+ new_stage_bin->baudrate = CONFIG_BAUDRATE;
-+}
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/spl/dram.h
-@@ -0,0 +1,39 @@
-+/* SPDX-License-Identifier: GPL-2.0 */
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#ifndef _MT7621_DRAM_H_
-+#define _MT7621_DRAM_H_
-+
-+#define STAGE_LOAD_ADDR 0xBE108800
-+
-+#ifndef __ASSEMBLY__
-+#include <linux/types.h>
-+
-+#define DDR_PARAM_SIZE 24
-+
-+struct stage_header {
-+ u32 jump_insn[2];
-+ u32 ep;
-+ u32 stage_size;
-+ u32 has_stage2;
-+ u32 next_ep;
-+ u32 next_size;
-+ u32 next_offset;
-+ u32 cpu_pll_cfg;
-+ u32 ddr_pll_cfg;
-+ u32 reserved2[6];
-+ char build_tag[32];
-+ u32 ddr3_act[DDR_PARAM_SIZE];
-+ u32 padding1[2];
-+ u32 ddr2_act[DDR_PARAM_SIZE];
-+ u32 padding2[2];
-+ u32 baudrate;
-+ u32 padding3;
-+};
-+#endif
-+
-+#endif /* _MT7621_DRAM_H_ */
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/spl/launch.c
-@@ -0,0 +1,100 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <asm/io.h>
-+#include <asm/cm.h>
-+#include <asm/sections.h>
-+#include <asm/addrspace.h>
-+#include <asm/mipsmtregs.h>
-+#include <linux/sizes.h>
-+#include <time.h>
-+#include <cpu_func.h>
-+#include "launch.h"
-+#include "../mt7621.h"
-+
-+/* Cluster Power Controller (CPC) offsets */
-+#define CPC_CL_OTHER 0x2010
-+#define CPC_CO_CMD 0x4000
-+
-+/* CPC_CL_OTHER fields */
-+#define CPC_CL_OTHER_CORENUM_SHIFT 16
-+#define CPC_CL_OTHER_CORENUM GENMASK(23, 16)
-+
-+/* CPC_CO_CMD */
-+#define PWR_UP 3
-+
-+#define NUM_CORES 2
-+#define NUM_CPUS 4
-+#define WAIT_CPUS_TIMEOUT 4000
-+
-+static void copy_launch_wait_code(void)
-+{
-+ memset((void *)KSEG1, 0, SZ_4K);
-+
-+ memcpy((void *)KSEG1ADDR(LAUNCH_WAITCODE),
-+ &launch_wait_code_start,
-+ &launch_wait_code_end - &launch_wait_code_start);
-+
-+ invalidate_dcache_range(KSEG0, SZ_4K);
-+}
-+
-+static void bootup_secondary_core(void)
-+{
-+ void __iomem *cpcbase = (void __iomem *)KSEG1ADDR(MIPS_CPC_BASE);
-+ int i;
-+
-+ for (i = 1; i < NUM_CORES; i++) {
-+ writel(i << CPC_CL_OTHER_CORENUM_SHIFT, cpcbase + CPC_CL_OTHER);
-+ writel(PWR_UP, cpcbase + CPC_CO_CMD);
-+ }
-+}
-+
-+void secondary_cpu_init(void)
-+{
-+ void __iomem *sysc = (void __iomem *)KSEG1ADDR(SYSCTL_BASE);
-+ u32 i, dual_core = 0, cpuready = 1, cpumask = 0x03;
-+ ulong wait_tick;
-+ struct cpulaunch_t *c;
-+
-+ /* Copy LAUNCH wait code used by other VPEs */
-+ copy_launch_wait_code();
-+
-+ dual_core = readl(sysc + SYSCTL_CHIP_REV_ID_REG) & CPU_ID;
-+
-+ if (dual_core) {
-+ /* Bootup secondary core for MT7621A */
-+ cpumask = 0x0f;
-+
-+ /* Make BootROM/TPL redirect Core1's bootup flow to our entry point */
-+ writel((uintptr_t)&_start, sysc + BOOT_SRAM_BASE_REG);
-+
-+ bootup_secondary_core();
-+ }
-+
-+ /* Join the coherent domain */
-+ join_coherent_domain(dual_core ? 2 : 1);
-+
-+ /* Bootup Core0/VPE1 */
-+ boot_vpe1();
-+
-+ /* Wait for all CPU ready */
-+ wait_tick = get_timer(0) + WAIT_CPUS_TIMEOUT;
-+
-+ while (time_before(get_timer(0), wait_tick)) {
-+ /* CPU0 is obviously ready */
-+ for (i = 1; i < NUM_CPUS; i++) {
-+ c = (struct cpulaunch_t *)(KSEG0ADDR(CPULAUNCH) +
-+ (i << LOG2CPULAUNCH));
-+
-+ if (c->flags & LAUNCH_FREADY)
-+ cpuready |= BIT(i);
-+ }
-+
-+ if ((cpuready & cpumask) == cpumask)
-+ break;
-+ }
-+}
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/spl/launch.h
-@@ -0,0 +1,52 @@
-+/* SPDX-License-Identifier: GPL-2.0 */
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#ifndef _LAUNCH_H_
-+#define _LAUNCH_H_
-+
-+#ifndef __ASSEMBLY__
-+
-+struct cpulaunch_t {
-+ unsigned long pc;
-+ unsigned long gp;
-+ unsigned long sp;
-+ unsigned long a0;
-+ unsigned long _pad[3]; /* pad to cache line size to avoid thrashing */
-+ unsigned long flags;
-+};
-+
-+extern char launch_wait_code_start;
-+extern char launch_wait_code_end;
-+
-+void join_coherent_domain(int ncores);
-+void boot_vpe1(void);
-+
-+#else
-+
-+#define LAUNCH_PC 0
-+#define LAUNCH_GP 4
-+#define LAUNCH_SP 8
-+#define LAUNCH_A0 12
-+#define LAUNCH_FLAGS 28
-+
-+#endif
-+
-+#define LOG2CPULAUNCH 5
-+
-+#define LAUNCH_FREADY 1
-+#define LAUNCH_FGO 2
-+#define LAUNCH_FGONE 4
-+
-+#define LAUNCH_WAITCODE 0x00000d00
-+#define SCRLAUNCH 0x00000e00
-+#define CPULAUNCH 0x00000f00
-+#define NCPULAUNCH 8
-+
-+/* Polling period in count cycles for secondary CPU's */
-+#define LAUNCHPERIOD 10000
-+
-+#endif /* _LAUNCH_H_ */
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/spl/launch_ll.S
-@@ -0,0 +1,339 @@
-+/* SPDX-License-Identifier: GPL-2.0 */
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <asm/cm.h>
-+#include <asm/asm.h>
-+#include <asm/regdef.h>
-+#include <asm/cacheops.h>
-+#include <asm/mipsregs.h>
-+#include <asm/addrspace.h>
-+#include <asm/mipsmtregs.h>
-+#include "launch.h"
-+
-+ .macro cache_loop curr, end, line_sz, op
-+10: cache \op, 0(\curr)
-+ PTR_ADDU \curr, \curr, \line_sz
-+ bne \curr, \end, 10b
-+ .endm
-+
-+ .set mt
-+
-+/*
-+ * Join the coherent domain
-+ * a0 = number of cores
-+ */
-+LEAF(join_coherent_domain)
-+ /*
-+ * Enable coherence and allow interventions from all other cores.
-+ * (Write access enabled via GCR_ACCESS by core 0.)
-+ */
-+ li t1, 1
-+ sll t1, a0
-+ addiu t1, -1
-+
-+ li t0, KSEG1ADDR(CONFIG_MIPS_CM_BASE)
-+ sw t1, GCR_Cx_COHERENCE(t0)
-+ ehb
-+
-+ move t2, zero
-+
-+_next_coherent_core:
-+ sll t1, t2, GCR_Cx_OTHER_CORENUM_SHIFT
-+ sw t1, GCR_Cx_OTHER(t0)
-+
-+_busy_wait_coherent_core:
-+ lw t1, GCR_CO_COHERENCE(t0)
-+ beqz t1, _busy_wait_coherent_core
-+
-+ addiu t2, 1
-+ bne t2, a0, _next_coherent_core
-+
-+ jr ra
-+ END(join_coherent_domain)
-+
-+/*
-+ * All VPEs other than VPE0 will go here.
-+ */
-+LEAF(launch_vpe_entry)
-+ mfc0 t0, CP0_EBASE
-+ and t0, t0, MIPS_EBASE_CPUNUM
-+
-+ /* per-VPE cpulaunch_t */
-+ li a0, KSEG0ADDR(CPULAUNCH)
-+ sll t1, t0, LOG2CPULAUNCH
-+ addu a0, t1
-+
-+ /* Set CPU online flag */
-+ li t0, LAUNCH_FREADY
-+ sw t0, LAUNCH_FLAGS(a0)
-+
-+ /* Enable count interrupt in mask, but do not enable interrupts */
-+ mfc0 t0, CP0_STATUS
-+ ori t0, STATUSF_IP7
-+ mtc0 t0, CP0_STATUS
-+
-+ /* VPEs executing in wait code do not need a stack */
-+ li t9, KSEG0ADDR(LAUNCH_WAITCODE)
-+ jr t9
-+ END(launch_vpe_entry)
-+
-+/*
-+ * This function will not be executed in place.
-+ * It will be copied into memory, and VPEs other than VPE0 will be
-+ * started to run into this in-memory function.
-+ */
-+LEAF(launch_wait_code)
-+ .globl launch_wait_code_start
-+launch_wait_code_start:
-+
-+ move t0, a0
-+
-+start_poll:
-+ /* Poll CPU go flag */
-+ mtc0 zero, CP0_COUNT
-+ li t1, LAUNCHPERIOD
-+ mtc0 t1, CP0_COMPARE
-+
-+time_wait:
-+ /* Software wait */
-+ mfc0 t2, CP0_COUNT
-+ subu t2, t1
-+ bltz t2, time_wait
-+
-+ /* Check the launch flag */
-+ lw t3, LAUNCH_FLAGS(t0)
-+ and t3, LAUNCH_FGO
-+ beqz t3, start_poll
-+
-+ /* Reset the counter and interrupts to give naive clients a chance */
-+ mfc0 t1, CP0_STATUS
-+ ins t1, zero, STATUSB_IP7, 1
-+ mtc0 t1, CP0_STATUS
-+
-+ mfc0 t1, CP0_COUNT
-+ subu t1, 1
-+ mtc0 t1, CP0_COMPARE
-+
-+ /* Jump to kernel */
-+ lw t9, LAUNCH_PC(t0)
-+ lw gp, LAUNCH_GP(t0)
-+ lw sp, LAUNCH_SP(t0)
-+ lw a0, LAUNCH_A0(t0)
-+ move a1, zero
-+ move a2, zero
-+ move a3, zero
-+ ori t3, LAUNCH_FGONE
-+ sw t3, LAUNCH_FLAGS(t0)
-+
-+ jr t9
-+
-+ .globl launch_wait_code_end
-+launch_wait_code_end:
-+ END(launch_wait_code)
-+
-+/*
-+ * Core1 will go here.
-+ */
-+LEAF(launch_core_entry)
-+ /* Disable caches */
-+ bal mips_cache_disable
-+
-+ /* Initialize L1 cache only */
-+ li a0, CONFIG_SYS_ICACHE_SIZE
-+ li a1, CONFIG_SYS_ICACHE_LINE_SIZE
-+ li a2, CONFIG_SYS_DCACHE_SIZE
-+ li a3, CONFIG_SYS_DCACHE_LINE_SIZE
-+
-+ mtc0 zero, CP0_TAGLO
-+ mtc0 zero, CP0_TAGLO, 2
-+ ehb
-+
-+ /*
-+ * Initialize the I-cache first,
-+ */
-+ li t0, KSEG0
-+ addu t1, t0, a0
-+ /* clear tag to invalidate */
-+ cache_loop t0, t1, a1, INDEX_STORE_TAG_I
-+#ifdef CONFIG_SYS_MIPS_CACHE_INIT_RAM_LOAD
-+ /* fill once, so data field parity is correct */
-+ PTR_LI t0, KSEG0
-+ cache_loop t0, t1, a1, FILL
-+ /* invalidate again - prudent but not strictly necessary */
-+ PTR_LI t0, KSEG0
-+ cache_loop t0, t1, a1, INDEX_STORE_TAG_I
-+#endif
-+
-+ /*
-+ * then initialize D-cache.
-+ */
-+ PTR_LI t0, KSEG0
-+ PTR_ADDU t1, t0, a2
-+ /* clear all tags */
-+ cache_loop t0, t1, a3, INDEX_STORE_TAG_D
-+#ifdef CONFIG_SYS_MIPS_CACHE_INIT_RAM_LOAD
-+ /* load from each line (in cached space) */
-+ PTR_LI t0, KSEG0
-+2: LONG_L zero, 0(t0)
-+ PTR_ADDU t0, a3
-+ bne t0, t1, 2b
-+ /* clear all tags */
-+ PTR_LI t0, KSEG0
-+ cache_loop t0, t1, a3, INDEX_STORE_TAG_D
-+#endif
-+
-+ /* Set Cache Mode */
-+ mfc0 t0, CP0_CONFIG
-+ li t1, CONF_CM_CACHABLE_COW
-+ ins t0, t1, 0, 3
-+ mtc0 t0, CP0_CONFIG
-+
-+ /* Join the coherent domain */
-+ li a0, 2
-+ bal join_coherent_domain
-+
-+ /* Bootup Core0/VPE1 */
-+ bal boot_vpe1
-+
-+ b launch_vpe_entry
-+ END(launch_core_entry)
-+
-+/*
-+ * Bootup VPE1.
-+ * This subroutine must be executed from VPE0 with VPECONF0[MVP] already set.
-+ */
-+LEAF(boot_vpe1)
-+ mfc0 t0, CP0_MVPCONF0
-+
-+ /* a0 = number of TCs - 1 */
-+ ext a0, t0, MVPCONF0_PTC_SHIFT, 8
-+ beqz a0, _vpe1_init_done
-+
-+ /* a1 = number of VPEs - 1 */
-+ ext a1, t0, MVPCONF0_PVPE_SHIFT, 4
-+ beqz a1, _vpe1_init_done
-+
-+ /* a2 = current TC No. */
-+ move a2, zero
-+
-+ /* Enter VPE Configuration State */
-+ mfc0 t0, CP0_MVPCONTROL
-+ or t0, MVPCONTROL_VPC
-+ mtc0 t0, CP0_MVPCONTROL
-+ ehb
-+
-+_next_tc:
-+ /* Set the TC number to be used on MTTR and MFTR instructions */
-+ mfc0 t0, CP0_VPECONTROL
-+ ins t0, a2, 0, 8
-+ mtc0 t0, CP0_VPECONTROL
-+ ehb
-+
-+ /* TC0 is already bound */
-+ beqz a2, _next_vpe
-+
-+ /* Halt current TC */
-+ li t0, TCHALT_H
-+ mttc0 t0, CP0_TCHALT
-+ ehb
-+
-+ /* If there is spare TC, bind it to the last VPE (VPE[a1]) */
-+ slt t1, a1, a2
-+ bnez t1, _vpe_bind_tc
-+ move t1, a1
-+
-+ /* Set Exclusive TC for active TC */
-+ mftc0 t0, CP0_VPECONF0
-+ ins t0, a2, VPECONF0_XTC_SHIFT, 8
-+ mttc0 t0, CP0_VPECONF0
-+
-+ move t1, a2
-+_vpe_bind_tc:
-+ /* Bind TC to a VPE */
-+ mftc0 t0, CP0_TCBIND
-+ ins t0, t1, TCBIND_CURVPE_SHIFT, 4
-+ mttc0 t0, CP0_TCBIND
-+
-+ /*
-+ * Set up CP0_TCSTATUS register:
-+ * Disable Coprocessor Usable bits
-+ * Disable MDMX/DSP ASE
-+ * Clear Dirty TC
-+ * not dynamically allocatable
-+ * not allocated
-+ * Kernel mode
-+ * interrupt exempt
-+ * ASID 0
-+ */
-+ li t0, TCSTATUS_IXMT
-+ mttc0 t0, CP0_TCSTATUS
-+
-+_next_vpe:
-+ slt t1, a1, a2
-+ bnez t1, _done_vpe # No more VPEs
-+
-+ /* Disable TC multi-threading */
-+ mftc0 t0, CP0_VPECONTROL
-+ ins t0, zero, VPECONTROL_TE_SHIFT, 1
-+ mttc0 t0, CP0_VPECONTROL
-+
-+ /* Skip following configuration for TC0 */
-+ beqz a2, _done_vpe
-+
-+ /* Deactivate VPE, set Master VPE */
-+ mftc0 t0, CP0_VPECONF0
-+ ins t0, zero, VPECONF0_VPA_SHIFT, 1
-+ or t0, VPECONF0_MVP
-+ mttc0 t0, CP0_VPECONF0
-+
-+ mfc0 t0, CP0_STATUS
-+ mttc0 t0, CP0_STATUS
-+
-+ mttc0 zero, CP0_EPC
-+ mttc0 zero, CP0_CAUSE
-+
-+ mfc0 t0, CP0_CONFIG
-+ mttc0 t0, CP0_CONFIG
-+
-+ /*
-+ * VPE1 of each core can execute cached as its L1 I$ has already
-+ * been initialized.
-+ * and the L2$ has been initialized or "disabled" via CCA override.
-+ */
-+ PTR_LA t0, _start
-+ mttc0 t0, CP0_TCRESTART
-+
-+ /* Unset Interrupt Exempt, set Activate Thread */
-+ mftc0 t0, CP0_TCSTATUS
-+ ins t0, zero, TCSTATUS_IXMT_SHIFT, 1
-+ ori t0, TCSTATUS_A
-+ mttc0 t0, CP0_TCSTATUS
-+
-+ /* Resume TC */
-+ mttc0 zero, CP0_TCHALT
-+
-+ /* Activate VPE */
-+ mftc0 t0, CP0_VPECONF0
-+ ori t0, VPECONF0_VPA
-+ mttc0 t0, CP0_VPECONF0
-+
-+_done_vpe:
-+ addu a2, 1
-+ sltu t0, a0, a2
-+ beqz t0, _next_tc
-+
-+ mfc0 t0, CP0_MVPCONTROL
-+ /* Enable all activated VPE to execute */
-+ ori t0, MVPCONTROL_EVP
-+ /* Exit VPE Configuration State */
-+ ins t0, zero, MVPCONTROL_VPC_SHIFT, 1
-+ mtc0 t0, CP0_MVPCONTROL
-+ ehb
-+
-+_vpe1_init_done:
-+ jr ra
-+ END(boot_vpe1)
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/spl/serial.c
-@@ -0,0 +1,24 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <asm/io.h>
-+#include "../mt7621.h"
-+
-+void mtmips_spl_serial_init(void)
-+{
-+#ifdef CONFIG_SPL_SERIAL
-+ void __iomem *base = ioremap_nocache(SYSCTL_BASE, SYSCTL_SIZE);
-+
-+#if CONFIG_CONS_INDEX == 1
-+ clrbits_32(base + SYSCTL_GPIOMODE_REG, UART1_MODE);
-+#elif CONFIG_CONS_INDEX == 2
-+ clrbits_32(base + SYSCTL_GPIOMODE_REG, UART2_MODE_M);
-+#elif CONFIG_CONS_INDEX == 3
-+ clrbits_32(base + SYSCTL_GPIOMODE_REG, UART3_MODE_M);
-+#endif /* CONFIG_CONS_INDEX */
-+#endif /* CONFIG_SPL_SERIAL */
-+}
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/spl/spl.c
-@@ -0,0 +1,95 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <spl.h>
-+#include <init.h>
-+#include <image.h>
-+#include <vsprintf.h>
-+#include <malloc.h>
-+#include <asm/io.h>
-+#include <asm/sections.h>
-+#include <asm/addrspace.h>
-+#include <asm/byteorder.h>
-+#include <asm/global_data.h>
-+#include <linux/sizes.h>
-+#include <mach/serial.h>
-+#include "../mt7621.h"
-+#include "dram.h"
-+
-+DECLARE_GLOBAL_DATA_PTR;
-+
-+struct tpl_info {
-+ u32 magic;
-+ u32 size;
-+};
-+
-+void set_timer_freq_simple(void)
-+{
-+ u32 div = get_xtal_mhz();
-+
-+ /* Round down cpu freq */
-+ gd->arch.timer_freq = rounddown(CONFIG_MT7621_CPU_FREQ, div) * 500000;
-+}
-+
-+void __noreturn board_init_f(ulong dummy)
-+{
-+ spl_init();
-+
-+#ifdef CONFIG_SPL_SERIAL
-+ /*
-+ * mtmips_spl_serial_init() is useful if debug uart is enabled,
-+ * or DM based serial is not enabled.
-+ */
-+ mtmips_spl_serial_init();
-+ preloader_console_init();
-+#endif
-+
-+ board_init_r(NULL, 0);
-+}
-+
-+void board_boot_order(u32 *spl_boot_list)
-+{
-+#ifdef CONFIG_MT7621_BOOT_FROM_NAND
-+ spl_boot_list[0] = BOOT_DEVICE_NAND;
-+#else
-+ spl_boot_list[0] = BOOT_DEVICE_NOR;
-+#endif
-+}
-+
-+unsigned long spl_nor_get_uboot_base(void)
-+{
-+ const struct tpl_info *tpli;
-+ const image_header_t *hdr;
-+ u32 addr;
-+
-+ addr = FLASH_MMAP_BASE + TPL_INFO_OFFSET;
-+ tpli = (const struct tpl_info *)KSEG1ADDR(addr);
-+
-+ if (tpli->magic == TPL_INFO_MAGIC) {
-+ addr = FLASH_MMAP_BASE + tpli->size;
-+ hdr = (const image_header_t *)KSEG1ADDR(addr);
-+
-+ if (image_get_magic(hdr) == IH_MAGIC) {
-+ addr += sizeof(*hdr) + image_get_size(hdr);
-+ return KSEG1ADDR(addr);
-+ }
-+ }
-+
-+ panic("Unable to locate SPL payload\n");
-+ return 0;
-+}
-+
-+uint32_t spl_nand_get_uboot_raw_page(void)
-+{
-+ const struct stage_header *sh = (const struct stage_header *)&_start;
-+ u32 addr;
-+
-+ addr = image_get_header_size() + be32_to_cpu(sh->stage_size);
-+ addr = ALIGN(addr, SZ_4K);
-+
-+ return addr;
-+}
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/spl/start.S
-@@ -0,0 +1,226 @@
-+/* SPDX-License-Identifier: GPL-2.0 */
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <asm-offsets.h>
-+#include <config.h>
-+#include <asm/asm.h>
-+#include <asm/regdef.h>
-+#include <asm/mipsregs.h>
-+#include <asm/cacheops.h>
-+#include <asm/addrspace.h>
-+#include <asm/mipsmtregs.h>
-+#include <asm/cm.h>
-+#include "../mt7621.h"
-+#include "dram.h"
-+
-+#ifndef CONFIG_SYS_INIT_SP_ADDR
-+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \
-+ CONFIG_SYS_INIT_SP_OFFSET)
-+#endif
-+
-+#define SP_ADDR_TEMP 0xbe10dff0
-+
-+ .macro init_wr sel
-+ MTC0 zero, CP0_WATCHLO,\sel
-+ mtc0 t1, CP0_WATCHHI,\sel
-+ .endm
-+
-+ .macro setup_stack_gd
-+ li t0, -16
-+ PTR_LI t1, CONFIG_SYS_INIT_SP_ADDR
-+ and sp, t1, t0 # force 16 byte alignment
-+ PTR_SUBU \
-+ sp, sp, GD_SIZE # reserve space for gd
-+ and sp, sp, t0 # force 16 byte alignment
-+ move k0, sp # save gd pointer
-+#if CONFIG_VAL(SYS_MALLOC_F_LEN) && \
-+ !CONFIG_IS_ENABLED(INIT_STACK_WITHOUT_MALLOC_F)
-+ li t2, CONFIG_VAL(SYS_MALLOC_F_LEN)
-+ PTR_SUBU \
-+ sp, sp, t2 # reserve space for early malloc
-+ and sp, sp, t0 # force 16 byte alignment
-+#endif
-+ move fp, sp
-+
-+ /* Clear gd */
-+ move t0, k0
-+1:
-+ PTR_S zero, 0(t0)
-+ PTR_ADDIU t0, PTRSIZE
-+ blt t0, t1, 1b
-+ nop
-+
-+#if CONFIG_VAL(SYS_MALLOC_F_LEN) && \
-+ !CONFIG_IS_ENABLED(INIT_STACK_WITHOUT_MALLOC_F)
-+ PTR_S sp, GD_MALLOC_BASE(k0) # gd->malloc_base offset
-+#endif
-+ .endm
-+
-+ .set noreorder
-+
-+ENTRY(_start)
-+ b 1f
-+ mtc0 zero, CP0_COUNT
-+
-+ /* Stage header required by BootROM */
-+ .org 0x8
-+ .word 0 # ep, filled by mkimage
-+ .word 0 # stage_size, filled by mkimage
-+ .word 0 # has_stage2
-+ .word 0 # next_ep
-+ .word 0 # next_size
-+ .word 0 # next_offset
-+
-+1:
-+ /* Init CP0 Status */
-+ mfc0 t0, CP0_STATUS
-+ and t0, ST0_IMPL
-+ or t0, ST0_BEV | ST0_ERL
-+ mtc0 t0, CP0_STATUS
-+ ehb
-+
-+ /* Clear Watch Status bits and disable watch exceptions */
-+ li t1, 0x7 # Clear I, R and W conditions
-+ init_wr 0
-+ init_wr 1
-+ init_wr 2
-+ init_wr 3
-+
-+ /* Clear WP, IV and SW interrupts */
-+ mtc0 zero, CP0_CAUSE
-+
-+ /* Clear timer interrupt (CP0_COUNT cleared on branch to 'reset') */
-+ mtc0 zero, CP0_COMPARE
-+
-+ /* VPE1 goes to wait code directly */
-+ mfc0 t0, CP0_TCBIND
-+ andi t0, TCBIND_CURVPE
-+ bnez t0, launch_vpe_entry
-+ nop
-+
-+ /* Core1 goes to specific launch entry */
-+ PTR_LI t0, KSEG1ADDR(CONFIG_MIPS_CM_BASE)
-+ lw t1, GCR_Cx_ID(t0)
-+ bnez t1, launch_core_entry
-+ nop
-+
-+ /* MT7530 reset */
-+ li t0, KSEG1ADDR(SYSCTL_BASE)
-+ lw t1, SYSCTL_RSTCTL_REG(t0)
-+ ori t1, MCM_RST
-+ sw t1, SYSCTL_RSTCTL_REG(t0)
-+
-+ /* Disable DMA route for PSE SRAM set by BootROM */
-+ PTR_LI t0, KSEG1ADDR(DMA_CFG_ARB_BASE)
-+ sw zero, DMA_ROUTE_REG(t0)
-+
-+ /* Set CPU clock to 500MHz (Required if boot from NAND) */
-+ li t0, KSEG1ADDR(SYSCTL_BASE)
-+ lw t1, SYSCTL_CLKCFG0_REG(t0)
-+ ins t1, zero, 30, 2 # CPU_CLK_SEL
-+ sw t1, SYSCTL_CLKCFG0_REG(t0)
-+
-+ /* Set CPU clock divider to 1/1 */
-+ li t0, KSEG1ADDR(RBUS_BASE)
-+ li t1, 0x101
-+ sw t1, RBUS_DYN_CFG0_REG(t0)
-+
-+ /* (Re-)initialize the SRAM */
-+ bal mips_sram_init
-+ nop
-+
-+ /* Set up temporary stack */
-+ li sp, SP_ADDR_TEMP
-+
-+ /* Setup full CPS */
-+ bal mips_cm_map
-+ nop
-+
-+ bal mt7621_cps_init
-+ nop
-+
-+ /* Prepare for CPU/DDR initialization binary blob */
-+ bal prepare_stage_bin
-+ nop
-+
-+ /* Call CPU/DDR initialization binary blob */
-+ li t9, STAGE_LOAD_ADDR
-+ jalr t9
-+ nop
-+
-+ /* Switch CPU PLL source */
-+ li t0, KSEG1ADDR(SYSCTL_BASE)
-+ lw t1, SYSCTL_CLKCFG0_REG(t0)
-+ li t2, 1
-+ ins t1, t2, CPU_CLK_SEL_S, 2
-+ sw t1, SYSCTL_CLKCFG0_REG(t0)
-+
-+ /*
-+ * Currently SPL is running on locked L2 cache (on KSEG0).
-+ * To reset the entire cache, we have to writeback SPL to DRAM first.
-+ * Cache flush won't work here. Use memcpy instead.
-+ */
-+
-+ la a0, __text_start
-+ move a1, a0
-+ la a2, __image_copy_end
-+ sub a2, a2, a1
-+ li a3, 5
-+ ins a0, a3, 29, 3 # convert to KSEG1
-+
-+ bal memcpy
-+ nop
-+
-+ /* Disable caches */
-+ bal mips_cache_disable
-+ nop
-+
-+ /* Reset caches */
-+ bal mips_cache_reset
-+ nop
-+
-+ /* Disable SRAM */
-+ li t0, KSEG1ADDR(FE_BASE)
-+ li t1, FE_PSE_RESET
-+ sw t1, FE_RST_GLO_REG(t0)
-+
-+ /* Clear the .bss section */
-+ la a0, __bss_start
-+ la a1, __bss_end
-+1: sw zero, 0(a0)
-+ addiu a0, 4
-+ ble a0, a1, 1b
-+ nop
-+
-+ /* Set up initial stack and global data */
-+ setup_stack_gd
-+
-+#if CONFIG_IS_ENABLED(INIT_STACK_WITHOUT_MALLOC_F)
-+ /* Set malloc base */
-+ li t0, (CONFIG_SYS_INIT_SP_ADDR + 15) & (~15)
-+ PTR_S t0, GD_MALLOC_BASE(k0) # gd->malloc_base offset
-+#endif
-+
-+#if defined(CONFIG_DEBUG_UART) && defined(CONFIG_SPL_SERIAL)
-+ /* Earliest point to set up debug uart */
-+ bal debug_uart_init
-+ nop
-+#endif
-+
-+ /* Setup timer */
-+ bal set_timer_freq_simple
-+ nop
-+
-+ /* Bootup secondary CPUs */
-+ bal secondary_cpu_init
-+ nop
-+
-+ move a0, zero # a0 <-- boot_flags = 0
-+ bal board_init_f
-+ move ra, zero
-+
-+ END(_start)
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/sram_init.S
-@@ -0,0 +1,22 @@
-+/* SPDX-License-Identifier: GPL-2.0 */
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <asm/addrspace.h>
-+#include <asm/asm.h>
-+#include <asm/regdef.h>
-+#include "mt7621.h"
-+
-+LEAF(mips_sram_init)
-+ li t0, KSEG1ADDR(FE_BASE)
-+ li t1, FE_PSE_RESET
-+ sw t1, FE_RST_GLO_REG(t0)
-+
-+ li t1, (FE_PSE_RAM | FE_PSE_MEM_EN)
-+ sw t1, FE_RST_GLO_REG(t0)
-+
-+ jr ra
-+ END(mips_sram_init)
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/tpl/Makefile
-@@ -0,0 +1,4 @@
-+
-+extra-y += start.o
-+
-+obj-y += tpl.o
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/tpl/start.S
-@@ -0,0 +1,161 @@
-+/* SPDX-License-Identifier: GPL-2.0 */
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <asm-offsets.h>
-+#include <config.h>
-+#include <asm/asm.h>
-+#include <asm/regdef.h>
-+#include <asm/addrspace.h>
-+#include <asm/mipsregs.h>
-+#include <asm/cm.h>
-+#include "../mt7621.h"
-+
-+#define SP_ADDR_TEMP 0xbe10dff0
-+
-+ .set noreorder
-+
-+ .macro init_wr sel
-+ MTC0 zero, CP0_WATCHLO,\sel
-+ mtc0 t1, CP0_WATCHHI,\sel
-+ .endm
-+
-+ .macro uhi_mips_exception
-+ move k0, t9 # preserve t9 in k0
-+ move k1, a0 # preserve a0 in k1
-+ li t9, 15 # UHI exception operation
-+ li a0, 0 # Use hard register context
-+ sdbbp 1 # Invoke UHI operation
-+ .endm
-+
-+ENTRY(_start)
-+ b reset
-+ mtc0 zero, CP0_COUNT
-+
-+ /*
-+ * Store TPL size here.
-+ * This will be used by SPL to locate u-boot payload.
-+ */
-+ .org TPL_INFO_OFFSET
-+ .word TPL_INFO_MAGIC
-+ .word __image_copy_len
-+
-+ /* Exception vector */
-+ .org 0x200
-+ /* TLB refill, 32 bit task */
-+ uhi_mips_exception
-+
-+ .org 0x280
-+ /* XTLB refill, 64 bit task */
-+ uhi_mips_exception
-+
-+ .org 0x300
-+ /* Cache error exception */
-+ uhi_mips_exception
-+
-+ .org 0x380
-+ /* General exception */
-+ uhi_mips_exception
-+
-+ .org 0x400
-+ /* Catch interrupt exceptions */
-+ uhi_mips_exception
-+
-+ .org 0x480
-+ /* EJTAG debug exception */
-+1: b 1b
-+ nop
-+
-+ .org 0x500
-+
-+reset:
-+ /* Set KSEG0 to Uncached */
-+ mfc0 t0, CP0_CONFIG
-+ ins t0, zero, 0, 3
-+ ori t0, t0, CONF_CM_UNCACHED
-+ mtc0 t0, CP0_CONFIG
-+ ehb
-+
-+ /* Check for CPU number */
-+ mfc0 t0, CP0_EBASE
-+ and t0, t0, MIPS_EBASE_CPUNUM
-+ beqz t0, 1f
-+ nop
-+
-+ /* Secondary core goes to specified SPL entry address */
-+ li t0, KSEG1ADDR(SYSCTL_BASE)
-+ lw t0, BOOT_SRAM_BASE_REG(t0)
-+ jr t0
-+ nop
-+
-+ /* Init CP0 Status */
-+1: mfc0 t0, CP0_STATUS
-+ and t0, ST0_IMPL
-+ or t0, ST0_BEV | ST0_ERL
-+ mtc0 t0, CP0_STATUS
-+ nop
-+
-+ /* Clear Watch Status bits and disable watch exceptions */
-+ li t1, 0x7 # Clear I, R and W conditions
-+ init_wr 0
-+ init_wr 1
-+ init_wr 2
-+ init_wr 3
-+
-+ /* Clear WP, IV and SW interrupts */
-+ mtc0 zero, CP0_CAUSE
-+
-+ /* Clear timer interrupt (CP0_COUNT cleared on branch to 'reset') */
-+ mtc0 zero, CP0_COMPARE
-+
-+ /* Setup basic CPS */
-+ bal mips_cm_map
-+ nop
-+
-+ li t0, KSEG1ADDR(CONFIG_MIPS_CM_BASE)
-+ li t1, GCR_REG0_BASE_VALUE
-+ sw t1, GCR_REG0_BASE(t0)
-+
-+ li t1, ((GCR_REG0_MASK_VALUE << GCR_REGn_MASK_ADDRMASK_SHIFT) | \
-+ GCR_REGn_MASK_CMTGT_IOCU0)
-+ sw t1, GCR_REG0_MASK(t0)
-+
-+ lw t1, GCR_BASE(t0)
-+ ins t1, zero, 0, 2 # CM_DEFAULT_TARGET
-+ sw t1, GCR_BASE(t0)
-+
-+ lw t1, GCR_CONTROL(t0)
-+ li t2, GCR_CONTROL_SYNCCTL
-+ or t1, t1, t2
-+ sw t1, GCR_CONTROL(t0)
-+
-+ /* Increase SPI frequency */
-+ li t0, KSEG1ADDR(SPI_BASE)
-+ li t1, 5
-+ sw t1, SPI_SPACE_REG(t0)
-+
-+ /* Set CPU clock to 500MHz */
-+ li t0, KSEG1ADDR(SYSCTL_BASE)
-+ lw t1, SYSCTL_CLKCFG0_REG(t0)
-+ ins t1, zero, 30, 2 # CPU_CLK_SEL
-+ sw t1, SYSCTL_CLKCFG0_REG(t0)
-+
-+ /* Set CPU clock divider to 1/1 */
-+ li t0, KSEG1ADDR(RBUS_BASE)
-+ li t1, 0x101
-+ sw t1, RBUS_DYN_CFG0_REG(t0)
-+
-+ /* Initialize the SRAM */
-+ bal mips_sram_init
-+ nop
-+
-+ /* Set up initial stack */
-+ li sp, SP_ADDR_TEMP
-+
-+ bal tpl_main
-+ nop
-+
-+ END(_start)
---- /dev/null
-+++ b/arch/mips/mach-mtmips/mt7621/tpl/tpl.c
-@@ -0,0 +1,144 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <image.h>
-+#include <asm/system.h>
-+#include <asm/sections.h>
-+#include <asm/cacheops.h>
-+#include <asm/mipsregs.h>
-+#include <asm/cm.h>
-+
-+#define INDEX_STORE_DATA_SD 0x0f
-+
-+typedef void __noreturn (*image_entry_noargs_t)(void);
-+
-+/*
-+ * Lock L2 cache and fill data
-+ * Assume that data is 4-byte aligned and start_addr/size is 32-byte aligned
-+ */
-+static void fill_lock_l2cache(uintptr_t dataptr, ulong start_addr, ulong size)
-+{
-+ ulong slsize = CONFIG_SYS_DCACHE_LINE_SIZE;
-+ ulong end_addr = start_addr + size;
-+ const u32 *data = (u32 *)dataptr;
-+ ulong i, addr;
-+ u32 val;
-+
-+ /* Clear WSC & SPR bit in ErrCtl */
-+ val = read_c0_ecc();
-+ val &= 0xcfffffff;
-+ write_c0_ecc(val);
-+ execution_hazard_barrier();
-+
-+ for (addr = start_addr; addr < end_addr; addr += slsize) {
-+ /* Set STagLo to lock cache line */
-+ write_c0_staglo((addr & 0x1ffff800) | 0xa0);
-+ mips_cache(INDEX_STORE_TAG_SD, (void *)addr);
-+
-+ /* Fill data */
-+ for (i = 0; i < slsize; i += 8) {
-+ val = *data++;
-+ __write_32bit_c0_register($28, 5, val); /* sdtaglo */
-+ val = *data++;
-+ __write_32bit_c0_register($29, 5, val); /* sdtaghi */
-+ mips_cache(INDEX_STORE_DATA_SD, (void *)(addr + i));
-+ }
-+ }
-+
-+ sync();
-+}
-+
-+/* A simple function to initialize MT7621's cache */
-+static void mt7621_cache_init(void)
-+{
-+ void __iomem *cm_base = (void *)KSEG1ADDR(CONFIG_MIPS_CM_BASE);
-+ ulong lsize = CONFIG_SYS_DCACHE_LINE_SIZE;
-+ ulong addr;
-+ u32 val;
-+
-+ /* Enable CCA override. Set to uncached */
-+ val = readl(cm_base + GCR_BASE);
-+ val &= ~CCA_DEFAULT_OVR_MASK;
-+ val |= CCA_DEFAULT_OVREN | (2 << CCA_DEFAULT_OVR_SHIFT);
-+ writel(val, cm_base + GCR_BASE);
-+
-+ /* Initialize L1 I-Cache */
-+ write_c0_taglo(0);
-+ write_c0_taghi(0);
-+
-+ for (addr = 0; addr < CONFIG_SYS_ICACHE_SIZE; addr += lsize)
-+ mips_cache(INDEX_STORE_TAG_I, (void *)addr);
-+
-+ /* Initialize L1 D-Cache */
-+ write_c0_dtaglo(0);
-+ __write_32bit_c0_register($29, 2, 0); /* dtaghi */
-+
-+ for (addr = 0; addr < CONFIG_SYS_DCACHE_SIZE; addr += lsize)
-+ mips_cache(INDEX_STORE_TAG_D, (void *)addr);
-+
-+ /* Initialize L2 Cache */
-+ write_c0_staglo(0);
-+ __write_32bit_c0_register($29, 4, 0); /* staghi */
-+
-+ for (addr = 0; addr < (256 << 10); addr += lsize)
-+ mips_cache(INDEX_STORE_TAG_SD, (void *)addr);
-+
-+ /* Dsiable CCA override */
-+ val = readl(cm_base + GCR_BASE);
-+ val &= ~(CCA_DEFAULT_OVR_MASK | CCA_DEFAULT_OVREN);
-+ writel(val, cm_base + GCR_BASE);
-+
-+ /* Set KSEG0 to non-coherent cached (important!) */
-+ val = read_c0_config();
-+ val &= ~CONF_CM_CMASK;
-+ val |= CONF_CM_CACHABLE_NONCOHERENT;
-+ write_c0_config(val);
-+ execution_hazard_barrier();
-+
-+ /* Again, invalidate L1 D-Cache */
-+ for (addr = 0; addr < CONFIG_SYS_DCACHE_SIZE; addr += lsize)
-+ mips_cache(INDEX_WRITEBACK_INV_D, (void *)addr);
-+
-+ /* Invalidate L1 I-Cache */
-+ for (addr = 0; addr < CONFIG_SYS_ICACHE_SIZE; addr += lsize)
-+ mips_cache(INDEX_INVALIDATE_I, (void *)addr);
-+
-+ /* Disable L2 cache bypass */
-+ val = read_c0_config2();
-+ val &= ~MIPS_CONF_IMPL;
-+ write_c0_config2(val);
-+ execution_hazard_barrier();
-+}
-+
-+void __noreturn tpl_main(void)
-+{
-+ const image_header_t *hdr = (const image_header_t *)__image_copy_end;
-+ image_entry_noargs_t image_entry;
-+ u32 loadaddr, size;
-+ uintptr_t data;
-+
-+ /* Initialize the cache first */
-+ mt7621_cache_init();
-+
-+ if (image_get_magic(hdr) != IH_MAGIC)
-+ goto failed;
-+
-+ loadaddr = image_get_load(hdr);
-+ size = image_get_size(hdr);
-+ image_entry = (image_entry_noargs_t)image_get_ep(hdr);
-+
-+ /* Load TPL image to L2 cache */
-+ data = (uintptr_t)__image_copy_end + sizeof(struct image_header);
-+ fill_lock_l2cache(data, loadaddr, size);
-+
-+ /* Jump to SPL */
-+ image_entry();
-+
-+failed:
-+ for (;;)
-+ ;
-+}
---- /dev/null
-+++ b/include/configs/mt7621.h
-@@ -0,0 +1,65 @@
-+/* SPDX-License-Identifier: GPL-2.0 */
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#ifndef __CONFIG_MT7621_H
-+#define __CONFIG_MT7621_H
-+
-+#define CONFIG_SYS_MIPS_TIMER_FREQ 440000000
-+
-+#define CONFIG_SYS_BOOTPARAMS_LEN 0x20000
-+
-+#define CONFIG_SYS_SDRAM_BASE 0x80000000
-+
-+#define CONFIG_VERY_BIG_RAM
-+#define CONFIG_MAX_MEM_MAPPED 0x1c000000
-+
-+#define CONFIG_SYS_INIT_SP_OFFSET 0x800000
-+
-+#define CONFIG_SYS_BOOTM_LEN 0x2000000
-+
-+#define CONFIG_SYS_MAXARGS 16
-+#define CONFIG_SYS_CBSIZE 1024
-+
-+#define CONFIG_SYS_NONCACHED_MEMORY 0x100000
-+
-+/* MMC */
-+#define MMC_SUPPORTS_TUNING
-+
-+/* NAND */
-+#define CONFIG_SYS_MAX_NAND_DEVICE 1
-+
-+/* Serial SPL */
-+#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_SERIAL)
-+#define CONFIG_SYS_NS16550_MEM32
-+#define CONFIG_SYS_NS16550_CLK 50000000
-+#define CONFIG_SYS_NS16550_REG_SIZE -4
-+#define CONFIG_SYS_NS16550_COM1 0xbe000c00
-+#endif
-+
-+/* Serial common */
-+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, \
-+ 230400, 460800, 921600 }
-+
-+/* SPL */
-+#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
-+
-+#ifdef CONFIG_TPL_BUILD
-+#define CONFIG_SPL_START_S_PATH "arch/mips/mach-mtmips/mt7621/tpl"
-+/* .bss will not be used by TPL */
-+#define CONFIG_SPL_BSS_START_ADDR 0x80000000
-+#define CONFIG_SPL_BSS_MAX_SIZE 0
-+#else
-+#define CONFIG_SPL_START_S_PATH "arch/mips/mach-mtmips/mt7621/spl"
-+#define CONFIG_SPL_BSS_START_ADDR 0x80140000
-+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
-+#define CONFIG_SPL_MAX_SIZE 0x30000
-+#endif
-+
-+/* Dummy value */
-+#define CONFIG_SYS_UBOOT_BASE 0
-+
-+#endif /* __CONFIG_MT7621_H */
+++ /dev/null
-From b1549087ecd1eb53f6173b17b473134fd6cca157 Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:22:26 +0800
-Subject: [PATCH 06/25] mips: mtmips: add two reference boards for mt7621
-
-The mt7621_rfb board supports integrated giga PHYs plus one external
-giga PHYs. It also has up to 512MiB DDR3, 16MB SPI-NOR, 3 mini PCI-e x1
-slots, SDXC and USB.
-
-The mt7621_nand_rfb board is almost the same as mt7621_rfb board, but it
-uses NAND flash and SDXC is not available.
-
-Reviewed-by: Stefan Roese <sr@denx.de>
-Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- arch/mips/dts/Makefile | 2 +
- arch/mips/dts/mediatek,mt7621-nand-rfb.dts | 67 +++++++++++++++++
- arch/mips/dts/mediatek,mt7621-rfb.dts | 82 +++++++++++++++++++++
- arch/mips/mach-mtmips/mt7621/Kconfig | 20 +++++
- board/mediatek/mt7621/MAINTAINERS | 8 ++
- board/mediatek/mt7621/Makefile | 3 +
- board/mediatek/mt7621/board.c | 6 ++
- configs/mt7621_nand_rfb_defconfig | 85 ++++++++++++++++++++++
- configs/mt7621_rfb_defconfig | 82 +++++++++++++++++++++
- 9 files changed, 355 insertions(+)
- create mode 100644 arch/mips/dts/mediatek,mt7621-nand-rfb.dts
- create mode 100644 arch/mips/dts/mediatek,mt7621-rfb.dts
- create mode 100644 board/mediatek/mt7621/MAINTAINERS
- create mode 100644 board/mediatek/mt7621/Makefile
- create mode 100644 board/mediatek/mt7621/board.c
- create mode 100644 configs/mt7621_nand_rfb_defconfig
- create mode 100644 configs/mt7621_rfb_defconfig
-
---- a/arch/mips/dts/Makefile
-+++ b/arch/mips/dts/Makefile
-@@ -16,6 +16,8 @@ dtb-$(CONFIG_BOARD_COMTREND_WAP5813N) +=
- dtb-$(CONFIG_BOARD_HUAWEI_HG556A) += huawei,hg556a.dtb
- dtb-$(CONFIG_BOARD_MT7620_RFB) += mediatek,mt7620-rfb.dtb
- dtb-$(CONFIG_BOARD_MT7620_MT7530_RFB) += mediatek,mt7620-mt7530-rfb.dtb
-+dtb-$(CONFIG_BOARD_MT7621_RFB) += mediatek,mt7621-rfb.dtb
-+dtb-$(CONFIG_BOARD_MT7621_NAND_RFB) += mediatek,mt7621-nand-rfb.dtb
- dtb-$(CONFIG_BOARD_MT7628_RFB) += mediatek,mt7628-rfb.dtb
- dtb-$(CONFIG_BOARD_GARDENA_SMART_GATEWAY_MT7688) += gardena-smart-gateway-mt7688.dtb
- dtb-$(CONFIG_BOARD_LINKIT_SMART_7688) += linkit-smart-7688.dtb
---- /dev/null
-+++ b/arch/mips/dts/mediatek,mt7621-nand-rfb.dts
-@@ -0,0 +1,67 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+/dts-v1/;
-+
-+#include "mt7621.dtsi"
-+
-+/ {
-+ compatible = "mediatek,mt7621-nand-rfb", "mediatek,mt7621-soc";
-+ model = "MediaTek MT7621 RFB (NAND)";
-+
-+ aliases {
-+ serial0 = &uart0;
-+ };
-+
-+ chosen {
-+ stdout-path = &uart0;
-+ };
-+};
-+
-+&pinctrl {
-+ state_default: pin_state {
-+ nand {
-+ groups = "spi", "sdxc";
-+ function = "nand";
-+ };
-+
-+ gpios {
-+ groups = "i2c", "uart3", "pcie reset";
-+ function = "gpio";
-+ };
-+
-+ wdt {
-+ groups = "wdt";
-+ function = "wdt rst";
-+ };
-+
-+ jtag {
-+ groups = "jtag";
-+ function = "jtag";
-+ };
-+ };
-+};
-+
-+&uart0 {
-+ status = "okay";
-+};
-+
-+&gpio {
-+ status = "okay";
-+};
-+
-+ð {
-+ status = "okay";
-+};
-+
-+&ssusb {
-+ status = "okay";
-+};
-+
-+&u3phy {
-+ status = "okay";
-+};
---- /dev/null
-+++ b/arch/mips/dts/mediatek,mt7621-rfb.dts
-@@ -0,0 +1,82 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+/dts-v1/;
-+
-+#include "mt7621.dtsi"
-+
-+/ {
-+ compatible = "mediatek,mt7621-rfb", "mediatek,mt7621-soc";
-+ model = "MediaTek MT7621 RFB (SPI-NOR)";
-+
-+ aliases {
-+ serial0 = &uart0;
-+ spi0 = &spi;
-+ };
-+
-+ chosen {
-+ stdout-path = &uart0;
-+ };
-+};
-+
-+&pinctrl {
-+ state_default: pin_state {
-+ gpios {
-+ groups = "i2c", "uart3", "pcie reset";
-+ function = "gpio";
-+ };
-+
-+ wdt {
-+ groups = "wdt";
-+ function = "wdt rst";
-+ };
-+
-+ jtag {
-+ groups = "jtag";
-+ function = "jtag";
-+ };
-+ };
-+};
-+
-+&uart0 {
-+ status = "okay";
-+};
-+
-+&gpio {
-+ status = "okay";
-+};
-+
-+&spi {
-+ status = "okay";
-+ num-cs = <2>;
-+
-+ spi-flash@0 {
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ compatible = "jedec,spi-nor";
-+ spi-max-frequency = <25000000>;
-+ reg = <0>;
-+ };
-+};
-+
-+ð {
-+ status = "okay";
-+};
-+
-+&mmc {
-+ cap-sd-highspeed;
-+
-+ status = "okay";
-+};
-+
-+&ssusb {
-+ status = "okay";
-+};
-+
-+&u3phy {
-+ status = "okay";
-+};
---- a/arch/mips/mach-mtmips/mt7621/Kconfig
-+++ b/arch/mips/mach-mtmips/mt7621/Kconfig
-@@ -79,6 +79,26 @@ config MT7621_BOOT_FROM_NAND
- choice
- prompt "Board select"
-
-+config BOARD_MT7621_RFB
-+ bool "MediaTek MT7621 RFB (SPI-NOR)"
-+ help
-+ The reference design of MT7621A (WS3010) booting from SPI-NOR flash.
-+ The board can be configured with DDR2 (64MiB~256MiB) or DDR3
-+ (128MiB~512MiB). The board has 16 MiB SPI-NOR flash, built-in MT7530
-+ GbE switch, 1 UART, 1 USB 2.0 host, 1 USB 3.0 host, 1 SDXC, 3 PCIe
-+ sockets, 1 RGMII to external GbE PHY, 2 audio jacks (in/out),
-+ JTAG pins and expansion GPIO pins.
-+
-+config BOARD_MT7621_NAND_RFB
-+ bool "MediaTek MT7621 RFB (NAND)"
-+ help
-+ The reference design of MT7621A (WS3010) booting from NAND flash.
-+ The board can be configured with DDR2 (64MiB~256MiB) or DDR3
-+ (128MiB~512MiB). The board has 128 MiB parallel NAND flash, built-in
-+ MT7530 GbE switch, 1 UART, 1 USB 2.0 host, 1 USB 3.0 host, 3 PCIe
-+ sockets, 1 RGMII to external GbE PHY, 2 audio jacks (in/out),
-+ JTAG pins and expansion GPIO pins.
-+
- endchoice
-
- config SYS_CONFIG_NAME
---- /dev/null
-+++ b/board/mediatek/mt7621/MAINTAINERS
-@@ -0,0 +1,8 @@
-+MT7621_RFB BOARD
-+M: Weijie Gao <weijie.gao@mediatek.com>
-+S: Maintained
-+F: board/mediatek/mt7621
-+F: configs/mt7621_rfb_defconfig
-+F: configs/mt7621_nand_rfb_defconfig
-+F: arch/mips/dts/mediatek,mt7621-rfb.dts
-+F: arch/mips/dts/mediatek,mt7621-nand-rfb.dts
---- /dev/null
-+++ b/board/mediatek/mt7621/Makefile
-@@ -0,0 +1,3 @@
-+# SPDX-License-Identifier: GPL-2.0
-+
-+obj-y += board.o
---- /dev/null
-+++ b/board/mediatek/mt7621/board.c
-@@ -0,0 +1,6 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
---- /dev/null
-+++ b/configs/mt7621_nand_rfb_defconfig
-@@ -0,0 +1,85 @@
-+CONFIG_MIPS=y
-+CONFIG_SYS_MALLOC_LEN=0x100000
-+CONFIG_SPL_LIBCOMMON_SUPPORT=y
-+CONFIG_SPL_LIBGENERIC_SUPPORT=y
-+CONFIG_NR_DRAM_BANKS=1
-+CONFIG_ENV_SIZE=0x1000
-+CONFIG_DEFAULT_DEVICE_TREE="mediatek,mt7621-nand-rfb"
-+CONFIG_SPL_SERIAL=y
-+CONFIG_SPL_SYS_MALLOC_F_LEN=0x100000
-+CONFIG_SPL=y
-+CONFIG_DEBUG_UART_BASE=0xbe000c00
-+CONFIG_DEBUG_UART_CLOCK=50000000
-+CONFIG_SYS_LOAD_ADDR=0x83000000
-+CONFIG_ARCH_MTMIPS=y
-+CONFIG_SOC_MT7621=y
-+CONFIG_MT7621_BOOT_FROM_NAND=y
-+CONFIG_BOARD_MT7621_NAND_RFB=y
-+# CONFIG_MIPS_CACHE_SETUP is not set
-+# CONFIG_MIPS_CACHE_DISABLE is not set
-+CONFIG_RESTORE_EXCEPTION_VECTOR_BASE=y
-+CONFIG_MIPS_BOOT_FDT=y
-+CONFIG_DEBUG_UART=y
-+CONFIG_FIT=y
-+# CONFIG_ARCH_FIXUP_FDT_MEMORY is not set
-+CONFIG_SYS_CONSOLE_INFO_QUIET=y
-+CONFIG_SPL_SYS_MALLOC_SIMPLE=y
-+CONFIG_SPL_NAND_SUPPORT=y
-+CONFIG_SPL_NAND_BASE=y
-+CONFIG_SPL_NAND_IDENT=y
-+# CONFIG_BOOTM_NETBSD is not set
-+# CONFIG_BOOTM_PLAN9 is not set
-+# CONFIG_BOOTM_RTEMS is not set
-+# CONFIG_BOOTM_VXWORKS is not set
-+# CONFIG_CMD_ELF is not set
-+# CONFIG_CMD_XIMG is not set
-+# CONFIG_CMD_CRC32 is not set
-+# CONFIG_CMD_DM is not set
-+# CONFIG_CMD_FLASH is not set
-+CONFIG_CMD_GPIO=y
-+# CONFIG_CMD_LOADS is not set
-+CONFIG_CMD_MMC=y
-+CONFIG_CMD_MTD=y
-+CONFIG_CMD_PART=y
-+# CONFIG_CMD_PINMUX is not set
-+CONFIG_CMD_USB=y
-+# CONFIG_CMD_NFS is not set
-+CONFIG_CMD_FAT=y
-+CONFIG_CMD_FS_GENERIC=y
-+# CONFIG_SPL_DOS_PARTITION is not set
-+# CONFIG_ISO_PARTITION is not set
-+CONFIG_EFI_PARTITION=y
-+# CONFIG_SPL_EFI_PARTITION is not set
-+CONFIG_PARTITION_TYPE_GUID=y
-+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-+CONFIG_NET_RANDOM_ETHADDR=y
-+# CONFIG_I2C is not set
-+# CONFIG_INPUT is not set
-+CONFIG_MMC=y
-+# CONFIG_MMC_QUIRKS is not set
-+# CONFIG_MMC_HW_PARTITIONING is not set
-+CONFIG_MMC_MTK=y
-+CONFIG_MTD=y
-+CONFIG_DM_MTD=y
-+CONFIG_MTD_RAW_NAND=y
-+CONFIG_NAND_MT7621=y
-+CONFIG_SYS_NAND_ONFI_DETECTION=y
-+CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
-+CONFIG_SYS_NAND_U_BOOT_OFFS=0x0
-+CONFIG_MEDIATEK_ETH=y
-+CONFIG_PHY=y
-+CONFIG_PHY_MTK_TPHY=y
-+CONFIG_DEBUG_UART_SHIFT=2
-+CONFIG_SYSRESET=y
-+CONFIG_SYSRESET_RESETCTL=y
-+CONFIG_USB=y
-+CONFIG_USB_XHCI_HCD=y
-+CONFIG_USB_XHCI_MTK=y
-+CONFIG_USB_STORAGE=y
-+CONFIG_WDT=y
-+CONFIG_WDT_MT7621=y
-+CONFIG_FAT_WRITE=y
-+# CONFIG_BINMAN_FDT is not set
-+CONFIG_LZMA=y
-+# CONFIG_GZIP is not set
-+CONFIG_SPL_LZMA=y
---- /dev/null
-+++ b/configs/mt7621_rfb_defconfig
-@@ -0,0 +1,82 @@
-+CONFIG_MIPS=y
-+CONFIG_SYS_MALLOC_LEN=0x100000
-+CONFIG_SPL_LIBCOMMON_SUPPORT=y
-+CONFIG_SPL_LIBGENERIC_SUPPORT=y
-+CONFIG_NR_DRAM_BANKS=1
-+CONFIG_ENV_SIZE=0x1000
-+CONFIG_DEFAULT_DEVICE_TREE="mediatek,mt7621-rfb"
-+CONFIG_SPL_SERIAL=y
-+CONFIG_SPL_SYS_MALLOC_F_LEN=0x40000
-+CONFIG_SPL=y
-+CONFIG_DEBUG_UART_BASE=0xbe000c00
-+CONFIG_DEBUG_UART_CLOCK=50000000
-+CONFIG_SYS_LOAD_ADDR=0x83000000
-+CONFIG_ARCH_MTMIPS=y
-+CONFIG_SOC_MT7621=y
-+# CONFIG_MIPS_CACHE_SETUP is not set
-+# CONFIG_MIPS_CACHE_DISABLE is not set
-+CONFIG_RESTORE_EXCEPTION_VECTOR_BASE=y
-+CONFIG_MIPS_BOOT_FDT=y
-+CONFIG_DEBUG_UART=y
-+CONFIG_TPL_SYS_MALLOC_F_LEN=0x1000
-+CONFIG_FIT=y
-+# CONFIG_ARCH_FIXUP_FDT_MEMORY is not set
-+CONFIG_SYS_CONSOLE_INFO_QUIET=y
-+CONFIG_SPL_SYS_MALLOC_SIMPLE=y
-+CONFIG_SPL_NOR_SUPPORT=y
-+CONFIG_TPL=y
-+# CONFIG_TPL_FRAMEWORK is not set
-+# CONFIG_BOOTM_NETBSD is not set
-+# CONFIG_BOOTM_PLAN9 is not set
-+# CONFIG_BOOTM_RTEMS is not set
-+# CONFIG_BOOTM_VXWORKS is not set
-+# CONFIG_CMD_ELF is not set
-+# CONFIG_CMD_XIMG is not set
-+# CONFIG_CMD_CRC32 is not set
-+# CONFIG_CMD_DM is not set
-+CONFIG_CMD_GPIO=y
-+# CONFIG_CMD_LOADS is not set
-+CONFIG_CMD_MMC=y
-+CONFIG_CMD_PART=y
-+# CONFIG_CMD_PINMUX is not set
-+CONFIG_CMD_SPI=y
-+# CONFIG_CMD_NFS is not set
-+CONFIG_DOS_PARTITION=y
-+# CONFIG_SPL_DOS_PARTITION is not set
-+# CONFIG_ISO_PARTITION is not set
-+CONFIG_EFI_PARTITION=y
-+# CONFIG_SPL_EFI_PARTITION is not set
-+CONFIG_PARTITION_TYPE_GUID=y
-+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-+CONFIG_NET_RANDOM_ETHADDR=y
-+# CONFIG_I2C is not set
-+# CONFIG_INPUT is not set
-+CONFIG_MMC=y
-+# CONFIG_MMC_QUIRKS is not set
-+# CONFIG_MMC_HW_PARTITIONING is not set
-+CONFIG_MMC_MTK=y
-+CONFIG_SF_DEFAULT_SPEED=20000000
-+CONFIG_SPI_FLASH_BAR=y
-+CONFIG_SPI_FLASH_EON=y
-+CONFIG_SPI_FLASH_GIGADEVICE=y
-+CONFIG_SPI_FLASH_ISSI=y
-+CONFIG_SPI_FLASH_MACRONIX=y
-+CONFIG_SPI_FLASH_SPANSION=y
-+CONFIG_SPI_FLASH_STMICRO=y
-+CONFIG_SPI_FLASH_WINBOND=y
-+CONFIG_SPI_FLASH_XMC=y
-+CONFIG_SPI_FLASH_XTX=y
-+CONFIG_MEDIATEK_ETH=y
-+CONFIG_PHY=y
-+CONFIG_PHY_MTK_TPHY=y
-+CONFIG_DEBUG_UART_SHIFT=2
-+CONFIG_SPI=y
-+CONFIG_MT7621_SPI=y
-+CONFIG_SYSRESET=y
-+CONFIG_SYSRESET_RESETCTL=y
-+CONFIG_WDT=y
-+CONFIG_WDT_MT7621=y
-+# CONFIG_BINMAN_FDT is not set
-+CONFIG_LZMA=y
-+# CONFIG_GZIP is not set
-+CONFIG_SPL_LZMA=y
+++ /dev/null
-From 3fed02d930597c53f1c8500aff14581bb87a1e3d Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:22:31 +0800
-Subject: [PATCH 07/25] doc: mediatek: add documentation for mt7621 reference
- boards
-
-The MT7621 requires external binary blob being executed during u-boot's
-boot-up flow. It's necessary to provide a guide here for users to correctly
-build the u-boot.
-
-Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- doc/board/index.rst | 1 +
- doc/board/mediatek/index.rst | 9 +++++++
- doc/board/mediatek/mt7621.rst | 48 +++++++++++++++++++++++++++++++++++
- 3 files changed, 58 insertions(+)
- create mode 100644 doc/board/mediatek/index.rst
- create mode 100644 doc/board/mediatek/mt7621.rst
-
---- a/doc/board/index.rst
-+++ b/doc/board/index.rst
-@@ -23,6 +23,7 @@ Board-specific doc
- highbank/index
- intel/index
- kontron/index
-+ mediatek/index
- microchip/index
- nokia/index
- nxp/index
---- /dev/null
-+++ b/doc/board/mediatek/index.rst
-@@ -0,0 +1,9 @@
-+.. SPDX-License-Identifier: GPL-2.0+
-+
-+Mediatek
-+=========
-+
-+.. toctree::
-+ :maxdepth: 2
-+
-+ mt7621
---- /dev/null
-+++ b/doc/board/mediatek/mt7621.rst
-@@ -0,0 +1,48 @@
-+.. SPDX-License-Identifier: GPL-2.0
-+
-+mt7621_rfb/mt7621_nand_rfb
-+==========================
-+
-+U-Boot for the MediaTek MT7621 boards
-+
-+Quick Start
-+-----------
-+
-+- Get the DDR initialization binary blob
-+- Configure CPU and DDR parameters
-+- Build U-Boot
-+
-+Get the DDR initialization binary blob
-+--------------------------------------
-+
-+Download one from:
-+ - https://raw.githubusercontent.com/mtk-openwrt/mt7621-lowlevel-preloader/master/mt7621_stage_sram.bin
-+ - https://raw.githubusercontent.com/mtk-openwrt/mt7621-lowlevel-preloader/master/mt7621_stage_sram_noprint.bin
-+
-+mt7621_stage_sram_noprint.bin has removed all output logs. To use this one,
-+download and rename it to mt7621_stage_sram.bin
-+
-+Put the binary blob to the u-boot build directory.
-+
-+Configure CPU and DDR parameters
-+--------------------------------
-+
-+menuconfig > MIPS architecture > MediaTek MIPS platforms > CPU & DDR configuration
-+
-+Select the correct DDR timing parameters for your board. The size shown here
-+must match the DDR size of you board.
-+
-+The frequency of CPU and DDR can also be adjusted.
-+
-+Build U-Boot
-+------------
-+
-+.. code-block:: bash
-+
-+ $ export CROSS_COMPILE=mipsel-linux-
-+ $ make O=build mt7621_rfb_defconfig # or mt7621_nand_rfb_defconfig
-+ $ cp mt7621_stage_sram.bin ./build/mt7621_stage_sram.bin
-+ $ # or cp mt7621_stage_sram_noprint.bin ./build/mt7621_stage_sram.bin
-+ $ make O=build
-+
-+Burn the u-boot-mt7621.bin to the SPI-NOR or NAND flash.
+++ /dev/null
-From c2e579662748cb5d3bf3e31f58d99c4db4d102c1 Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:22:36 +0800
-Subject: [PATCH 08/25] clk: mtmips: add clock driver for MediaTek MT7621 SoC
-
-This patch adds a clock driver for MediaTek MT7621 SoC.
-This driver provides clock gate control as well as getting clock frequency
-for CPU/SYS/XTAL and some peripherals.
-
-Reviewed-by: Sean Anderson <seanga2@gmail.com>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- drivers/clk/mtmips/Makefile | 1 +
- drivers/clk/mtmips/clk-mt7621.c | 288 +++++++++++++++++++++++++
- include/dt-bindings/clock/mt7621-clk.h | 46 ++++
- 3 files changed, 335 insertions(+)
- create mode 100644 drivers/clk/mtmips/clk-mt7621.c
- create mode 100644 include/dt-bindings/clock/mt7621-clk.h
-
---- a/drivers/clk/mtmips/Makefile
-+++ b/drivers/clk/mtmips/Makefile
-@@ -1,4 +1,5 @@
- # SPDX-License-Identifier: GPL-2.0
-
- obj-$(CONFIG_SOC_MT7620) += clk-mt7620.o
-+obj-$(CONFIG_SOC_MT7621) += clk-mt7621.o
- obj-$(CONFIG_SOC_MT7628) += clk-mt7628.o
---- /dev/null
-+++ b/drivers/clk/mtmips/clk-mt7621.c
-@@ -0,0 +1,288 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <clk-uclass.h>
-+#include <dm.h>
-+#include <dm/device_compat.h>
-+#include <regmap.h>
-+#include <syscon.h>
-+#include <dt-bindings/clock/mt7621-clk.h>
-+#include <linux/io.h>
-+#include <linux/bitops.h>
-+#include <linux/bitfield.h>
-+
-+#define SYSC_MAP_SIZE 0x100
-+#define MEMC_MAP_SIZE 0x1000
-+
-+/* SYSC */
-+#define SYSCFG0_REG 0x10
-+#define XTAL_MODE_SEL GENMASK(8, 6)
-+
-+#define CLKCFG0_REG 0x2c
-+#define CPU_CLK_SEL GENMASK(31, 30)
-+#define PERI_CLK_SEL BIT(4)
-+
-+#define CLKCFG1_REG 0x30
-+
-+#define CUR_CLK_STS_REG 0x44
-+#define CUR_CPU_FDIV GENMASK(12, 8)
-+#define CUR_CPU_FFRAC GENMASK(4, 0)
-+
-+/* MEMC */
-+#define MEMPLL1_REG 0x0604
-+#define RG_MEPL_DIV2_SEL GENMASK(2, 1)
-+
-+#define MEMPLL6_REG 0x0618
-+#define MEMPLL18_REG 0x0648
-+#define RG_MEPL_PREDIV GENMASK(13, 12)
-+#define RG_MEPL_FBDIV GENMASK(10, 4)
-+
-+/* Fixed 500M clock */
-+#define GMPLL_CLK 500000000
-+
-+struct mt7621_clk_priv {
-+ void __iomem *sysc_base;
-+ int cpu_clk;
-+ int ddr_clk;
-+ int sys_clk;
-+ int xtal_clk;
-+};
-+
-+enum mt7621_clk_src {
-+ CLK_SRC_CPU,
-+ CLK_SRC_DDR,
-+ CLK_SRC_SYS,
-+ CLK_SRC_XTAL,
-+ CLK_SRC_PERI,
-+ CLK_SRC_125M,
-+ CLK_SRC_150M,
-+ CLK_SRC_250M,
-+ CLK_SRC_270M,
-+
-+ __CLK_SRC_MAX
-+};
-+
-+struct mt7621_clk_map {
-+ u32 cgbit;
-+ enum mt7621_clk_src clksrc;
-+};
-+
-+#define CLK_MAP(_id, _cg, _src) \
-+ [_id] = { .cgbit = (_cg), .clksrc = (_src) }
-+
-+#define CLK_MAP_SRC(_id, _src) \
-+ [_id] = { .cgbit = UINT32_MAX, .clksrc = (_src) }
-+
-+static const struct mt7621_clk_map mt7621_clk_mappings[] = {
-+ CLK_MAP_SRC(MT7621_CLK_XTAL, CLK_SRC_XTAL),
-+ CLK_MAP_SRC(MT7621_CLK_CPU, CLK_SRC_CPU),
-+ CLK_MAP_SRC(MT7621_CLK_BUS, CLK_SRC_SYS),
-+ CLK_MAP_SRC(MT7621_CLK_50M, CLK_SRC_PERI),
-+ CLK_MAP_SRC(MT7621_CLK_125M, CLK_SRC_125M),
-+ CLK_MAP_SRC(MT7621_CLK_150M, CLK_SRC_150M),
-+ CLK_MAP_SRC(MT7621_CLK_250M, CLK_SRC_250M),
-+ CLK_MAP_SRC(MT7621_CLK_270M, CLK_SRC_270M),
-+
-+ CLK_MAP(MT7621_CLK_HSDMA, 5, CLK_SRC_150M),
-+ CLK_MAP(MT7621_CLK_FE, 6, CLK_SRC_250M),
-+ CLK_MAP(MT7621_CLK_SP_DIVTX, 7, CLK_SRC_270M),
-+ CLK_MAP(MT7621_CLK_TIMER, 8, CLK_SRC_PERI),
-+ CLK_MAP(MT7621_CLK_PCM, 11, CLK_SRC_270M),
-+ CLK_MAP(MT7621_CLK_PIO, 13, CLK_SRC_PERI),
-+ CLK_MAP(MT7621_CLK_GDMA, 14, CLK_SRC_SYS),
-+ CLK_MAP(MT7621_CLK_NAND, 15, CLK_SRC_125M),
-+ CLK_MAP(MT7621_CLK_I2C, 16, CLK_SRC_PERI),
-+ CLK_MAP(MT7621_CLK_I2S, 17, CLK_SRC_270M),
-+ CLK_MAP(MT7621_CLK_SPI, 18, CLK_SRC_SYS),
-+ CLK_MAP(MT7621_CLK_UART1, 19, CLK_SRC_PERI),
-+ CLK_MAP(MT7621_CLK_UART2, 20, CLK_SRC_PERI),
-+ CLK_MAP(MT7621_CLK_UART3, 21, CLK_SRC_PERI),
-+ CLK_MAP(MT7621_CLK_ETH, 23, CLK_SRC_PERI),
-+ CLK_MAP(MT7621_CLK_PCIE0, 24, CLK_SRC_125M),
-+ CLK_MAP(MT7621_CLK_PCIE1, 25, CLK_SRC_125M),
-+ CLK_MAP(MT7621_CLK_PCIE2, 26, CLK_SRC_125M),
-+ CLK_MAP(MT7621_CLK_CRYPTO, 29, CLK_SRC_250M),
-+ CLK_MAP(MT7621_CLK_SHXC, 30, CLK_SRC_PERI),
-+
-+ CLK_MAP_SRC(MT7621_CLK_MAX, __CLK_SRC_MAX),
-+
-+ CLK_MAP_SRC(MT7621_CLK_DDR, CLK_SRC_DDR),
-+};
-+
-+static ulong mt7621_clk_get_rate(struct clk *clk)
-+{
-+ struct mt7621_clk_priv *priv = dev_get_priv(clk->dev);
-+ u32 val;
-+
-+ switch (mt7621_clk_mappings[clk->id].clksrc) {
-+ case CLK_SRC_CPU:
-+ return priv->cpu_clk;
-+ case CLK_SRC_DDR:
-+ return priv->ddr_clk;
-+ case CLK_SRC_SYS:
-+ return priv->sys_clk;
-+ case CLK_SRC_XTAL:
-+ return priv->xtal_clk;
-+ case CLK_SRC_PERI:
-+ val = readl(priv->sysc_base + CLKCFG0_REG);
-+ if (val & PERI_CLK_SEL)
-+ return priv->xtal_clk;
-+ else
-+ return GMPLL_CLK / 10;
-+ case CLK_SRC_125M:
-+ return 125000000;
-+ case CLK_SRC_150M:
-+ return 150000000;
-+ case CLK_SRC_250M:
-+ return 250000000;
-+ case CLK_SRC_270M:
-+ return 270000000;
-+ default:
-+ return 0;
-+ }
-+}
-+
-+static int mt7621_clk_enable(struct clk *clk)
-+{
-+ struct mt7621_clk_priv *priv = dev_get_priv(clk->dev);
-+ u32 cgbit;
-+
-+ cgbit = mt7621_clk_mappings[clk->id].cgbit;
-+ if (cgbit == UINT32_MAX)
-+ return -ENOSYS;
-+
-+ setbits_32(priv->sysc_base + CLKCFG1_REG, BIT(cgbit));
-+
-+ return 0;
-+}
-+
-+static int mt7621_clk_disable(struct clk *clk)
-+{
-+ struct mt7621_clk_priv *priv = dev_get_priv(clk->dev);
-+ u32 cgbit;
-+
-+ cgbit = mt7621_clk_mappings[clk->id].cgbit;
-+ if (cgbit == UINT32_MAX)
-+ return -ENOSYS;
-+
-+ clrbits_32(priv->sysc_base + CLKCFG1_REG, BIT(cgbit));
-+
-+ return 0;
-+}
-+
-+static int mt7621_clk_request(struct clk *clk)
-+{
-+ if (clk->id >= ARRAY_SIZE(mt7621_clk_mappings))
-+ return -EINVAL;
-+ return 0;
-+}
-+
-+const struct clk_ops mt7621_clk_ops = {
-+ .request = mt7621_clk_request,
-+ .enable = mt7621_clk_enable,
-+ .disable = mt7621_clk_disable,
-+ .get_rate = mt7621_clk_get_rate,
-+};
-+
-+static void mt7621_get_clocks(struct mt7621_clk_priv *priv, struct regmap *memc)
-+{
-+ u32 bs, xtal_sel, clkcfg0, cur_clk, mempll, dividx, fb;
-+ u32 xtal_clk, xtal_div, ffiv, ffrac, cpu_clk, ddr_clk;
-+ static const u32 xtal_div_tbl[] = {0, 1, 2, 2};
-+
-+ bs = readl(priv->sysc_base + SYSCFG0_REG);
-+ clkcfg0 = readl(priv->sysc_base + CLKCFG0_REG);
-+ cur_clk = readl(priv->sysc_base + CUR_CLK_STS_REG);
-+
-+ xtal_sel = FIELD_GET(XTAL_MODE_SEL, bs);
-+
-+ if (xtal_sel <= 2)
-+ xtal_clk = 20 * 1000 * 1000;
-+ else if (xtal_sel <= 5)
-+ xtal_clk = 40 * 1000 * 1000;
-+ else
-+ xtal_clk = 25 * 1000 * 1000;
-+
-+ switch (FIELD_GET(CPU_CLK_SEL, clkcfg0)) {
-+ case 0:
-+ cpu_clk = GMPLL_CLK;
-+ break;
-+ case 1:
-+ regmap_read(memc, MEMPLL18_REG, &mempll);
-+ dividx = FIELD_GET(RG_MEPL_PREDIV, mempll);
-+ fb = FIELD_GET(RG_MEPL_FBDIV, mempll);
-+ xtal_div = 1 << xtal_div_tbl[dividx];
-+ cpu_clk = (fb + 1) * xtal_clk / xtal_div;
-+ break;
-+ default:
-+ cpu_clk = xtal_clk;
-+ }
-+
-+ ffiv = FIELD_GET(CUR_CPU_FDIV, cur_clk);
-+ ffrac = FIELD_GET(CUR_CPU_FFRAC, cur_clk);
-+ cpu_clk = cpu_clk / ffiv * ffrac;
-+
-+ regmap_read(memc, MEMPLL6_REG, &mempll);
-+ dividx = FIELD_GET(RG_MEPL_PREDIV, mempll);
-+ fb = FIELD_GET(RG_MEPL_FBDIV, mempll);
-+ xtal_div = 1 << xtal_div_tbl[dividx];
-+ ddr_clk = fb * xtal_clk / xtal_div;
-+
-+ regmap_read(memc, MEMPLL1_REG, &bs);
-+ if (!FIELD_GET(RG_MEPL_DIV2_SEL, bs))
-+ ddr_clk *= 2;
-+
-+ priv->cpu_clk = cpu_clk;
-+ priv->sys_clk = cpu_clk / 4;
-+ priv->ddr_clk = ddr_clk;
-+ priv->xtal_clk = xtal_clk;
-+}
-+
-+static int mt7621_clk_probe(struct udevice *dev)
-+{
-+ struct mt7621_clk_priv *priv = dev_get_priv(dev);
-+ struct ofnode_phandle_args args;
-+ struct udevice *pdev;
-+ struct regmap *memc;
-+ int ret;
-+
-+ pdev = dev_get_parent(dev);
-+ if (!pdev)
-+ return -ENODEV;
-+
-+ priv->sysc_base = dev_remap_addr(pdev);
-+ if (!priv->sysc_base)
-+ return -EINVAL;
-+
-+ /* get corresponding memc phandle */
-+ ret = dev_read_phandle_with_args(dev, "mediatek,memc", NULL, 0, 0,
-+ &args);
-+ if (ret)
-+ return ret;
-+
-+ memc = syscon_node_to_regmap(args.node);
-+ if (IS_ERR(memc))
-+ return PTR_ERR(memc);
-+
-+ mt7621_get_clocks(priv, memc);
-+
-+ return 0;
-+}
-+
-+static const struct udevice_id mt7621_clk_ids[] = {
-+ { .compatible = "mediatek,mt7621-clk" },
-+ { }
-+};
-+
-+U_BOOT_DRIVER(mt7621_clk) = {
-+ .name = "mt7621-clk",
-+ .id = UCLASS_CLK,
-+ .of_match = mt7621_clk_ids,
-+ .probe = mt7621_clk_probe,
-+ .priv_auto = sizeof(struct mt7621_clk_priv),
-+ .ops = &mt7621_clk_ops,
-+};
---- /dev/null
-+++ b/include/dt-bindings/clock/mt7621-clk.h
-@@ -0,0 +1,46 @@
-+/* SPDX-License-Identifier: GPL-2.0 */
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#ifndef _DT_BINDINGS_MT7621_CLK_H_
-+#define _DT_BINDINGS_MT7621_CLK_H_
-+
-+#define MT7621_CLK_XTAL 0
-+#define MT7621_CLK_CPU 1
-+#define MT7621_CLK_BUS 2
-+#define MT7621_CLK_50M 3
-+#define MT7621_CLK_125M 4
-+#define MT7621_CLK_150M 5
-+#define MT7621_CLK_250M 6
-+#define MT7621_CLK_270M 7
-+
-+#define MT7621_CLK_HSDMA 8
-+#define MT7621_CLK_FE 9
-+#define MT7621_CLK_SP_DIVTX 10
-+#define MT7621_CLK_TIMER 11
-+#define MT7621_CLK_PCM 12
-+#define MT7621_CLK_PIO 13
-+#define MT7621_CLK_GDMA 14
-+#define MT7621_CLK_NAND 15
-+#define MT7621_CLK_I2C 16
-+#define MT7621_CLK_I2S 17
-+#define MT7621_CLK_SPI 18
-+#define MT7621_CLK_UART1 19
-+#define MT7621_CLK_UART2 20
-+#define MT7621_CLK_UART3 21
-+#define MT7621_CLK_ETH 22
-+#define MT7621_CLK_PCIE0 23
-+#define MT7621_CLK_PCIE1 24
-+#define MT7621_CLK_PCIE2 25
-+#define MT7621_CLK_CRYPTO 26
-+#define MT7621_CLK_SHXC 27
-+
-+#define MT7621_CLK_MAX 28
-+
-+/* for u-boot only */
-+#define MT7621_CLK_DDR 29
-+
-+#endif /* _DT_BINDINGS_MT7621_CLK_H_ */
+++ /dev/null
-From 03035a6566300808c8845799b2f9ceca471aa61a Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:22:41 +0800
-Subject: [PATCH 09/25] reset: mtmips: add reset controller support for
- MediaTek MT7621 SoC
-
-This patch adds reset controller bits definition header file for MediaTek
-MT7621 SoC
-
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- include/dt-bindings/reset/mt7621-reset.h | 38 ++++++++++++++++++++++++
- 1 file changed, 38 insertions(+)
- create mode 100644 include/dt-bindings/reset/mt7621-reset.h
-
---- /dev/null
-+++ b/include/dt-bindings/reset/mt7621-reset.h
-@@ -0,0 +1,38 @@
-+/* SPDX-License-Identifier: GPL-2.0 */
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#ifndef _DT_BINDINGS_MT7621_RESET_H_
-+#define _DT_BINDINGS_MT7621_RESET_H_
-+
-+#define RST_PPE 31
-+#define RST_SDXC 30
-+#define RST_CRYPTO 29
-+#define RST_AUX_STCK 28
-+#define RST_PCIE2 26
-+#define RST_PCIE1 25
-+#define RST_PCIE0 24
-+#define RST_GMAC 23
-+#define RST_UART3 21
-+#define RST_UART2 20
-+#define RST_UART1 19
-+#define RST_SPI 18
-+#define RST_I2S 17
-+#define RST_I2C 16
-+#define RST_NFI 15
-+#define RST_GDMA 14
-+#define RST_PIO 13
-+#define RST_PCM 11
-+#define RST_MC 10
-+#define RST_INTC 9
-+#define RST_TIMER 8
-+#define RST_SPDIFTX 7
-+#define RST_FE 6
-+#define RST_HSDMA 5
-+#define RST_MCM 2
-+#define RST_SYS 0
-+
-+#endif /* _DT_BINDINGS_MT7621_RESET_H_ */
+++ /dev/null
-From 3cf9e2daca330a0ba89d3793ceb09037c788db46 Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:22:49 +0800
-Subject: [PATCH 10/25] pinctrl: mtmips: add support for MediaTek MT7621 SoC
-
-This patch adds pinctrl support for MediaTek MT7621 SoC.
-The MT7621 SoC supports pinconf, but it is not the same as mt7628.
-
-Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- drivers/pinctrl/mtmips/Kconfig | 9 +
- drivers/pinctrl/mtmips/Makefile | 1 +
- drivers/pinctrl/mtmips/pinctrl-mt7621.c | 306 ++++++++++++++++++
- .../pinctrl/mtmips/pinctrl-mtmips-common.c | 4 +-
- .../pinctrl/mtmips/pinctrl-mtmips-common.h | 12 +
- 5 files changed, 330 insertions(+), 2 deletions(-)
- create mode 100644 drivers/pinctrl/mtmips/pinctrl-mt7621.c
-
---- a/drivers/pinctrl/mtmips/Kconfig
-+++ b/drivers/pinctrl/mtmips/Kconfig
-@@ -12,6 +12,15 @@ config PINCTRL_MT7620
- The driver is controlled by a device tree node which contains
- the pin mux functions for each available pin groups.
-
-+config PINCTRL_MT7621
-+ bool "MediaTek MT7621 pin control driver"
-+ select PINCTRL_MTMIPS
-+ depends on SOC_MT7621 && PINCTRL_GENERIC
-+ help
-+ Support pin multiplexing control on MediaTek MT7621.
-+ The driver is controlled by a device tree node which contains
-+ the pin mux functions for each available pin groups.
-+
- config PINCTRL_MT7628
- bool "MediaTek MT7628 pin control driver"
- select PINCTRL_MTMIPS
---- a/drivers/pinctrl/mtmips/Makefile
-+++ b/drivers/pinctrl/mtmips/Makefile
-@@ -5,4 +5,5 @@ obj-$(CONFIG_PINCTRL_MTMIPS) += pinctrl-
-
- # SoC Drivers
- obj-$(CONFIG_PINCTRL_MT7620) += pinctrl-mt7620.o
-+obj-$(CONFIG_PINCTRL_MT7621) += pinctrl-mt7621.o
- obj-$(CONFIG_PINCTRL_MT7628) += pinctrl-mt7628.o
---- /dev/null
-+++ b/drivers/pinctrl/mtmips/pinctrl-mt7621.c
-@@ -0,0 +1,306 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <dm.h>
-+#include <dm/pinctrl.h>
-+#include <dm/device_compat.h>
-+#include <linux/bitops.h>
-+#include <linux/io.h>
-+
-+#include "pinctrl-mtmips-common.h"
-+
-+#define SYSC_MAP_SIZE 0x100
-+
-+#define PAD_UART1_GPIO0_OFS 0x00
-+#define PAD_UART3_I2C_OFS 0x04
-+#define PAD_UART2_JTAG_OFS 0x08
-+#define PAD_PERST_WDT_OFS 0x0c
-+#define PAD_RGMII2_MDIO_OFS 0x10
-+#define PAD_SDXC_SPI_OFS 0x14
-+#define GPIOMODE_OFS 0x18
-+#define PAD_BOPT_ESWINT_OFS 0x28
-+
-+#define ESWINT_SHIFT 20
-+#define SDXC_SHIFT 18
-+#define SPI_SHIFT 16
-+#define RGMII2_SHIFT 15
-+#define RGMII1_SHIFT 14
-+#define MDIO_SHIFT 12
-+#define PERST_SHIFT 10
-+#define WDT_SHIFT 8
-+#define JTAG_SHIFT 7
-+#define UART2_SHIFT 5
-+#define UART3_SHIFT 3
-+#define I2C_SHIFT 2
-+#define UART1_SHIFT 1
-+#define GPIO0_SHIFT 0 /* Dummy */
-+
-+#define GM4_MASK 3
-+
-+#define E4_E2_M 0x03
-+#define E4_E2_S 4
-+#define PULL_UP BIT(3)
-+#define PULL_DOWN BIT(2)
-+#define SMT BIT(1)
-+#define SR BIT(0)
-+
-+struct mt7621_pinctrl_priv {
-+ struct mtmips_pinctrl_priv mp;
-+};
-+
-+#if CONFIG_IS_ENABLED(PINMUX)
-+static const struct mtmips_pmx_func esw_int_grp[] = {
-+ FUNC("gpio", 1),
-+ FUNC("esw int", 0),
-+};
-+
-+static const struct mtmips_pmx_func sdxc_grp[] = {
-+ FUNC("nand", 2),
-+ FUNC("gpio", 1),
-+ FUNC("sdxc", 0),
-+};
-+
-+static const struct mtmips_pmx_func spi_grp[] = {
-+ FUNC("nand", 2),
-+ FUNC("gpio", 1),
-+ FUNC("spi", 0),
-+};
-+
-+static const struct mtmips_pmx_func rgmii2_grp[] = {
-+ FUNC("gpio", 1),
-+ FUNC("rgmii", 0),
-+};
-+
-+static const struct mtmips_pmx_func rgmii1_grp[] = {
-+ FUNC("gpio", 1),
-+ FUNC("rgmii", 0),
-+};
-+
-+static const struct mtmips_pmx_func mdio_grp[] = {
-+ FUNC("gpio", 1),
-+ FUNC("mdio", 0),
-+};
-+
-+static const struct mtmips_pmx_func perst_grp[] = {
-+ FUNC("refclk", 2),
-+ FUNC("gpio", 1),
-+ FUNC("pcie reset", 0),
-+};
-+
-+static const struct mtmips_pmx_func wdt_grp[] = {
-+ FUNC("refclk", 2),
-+ FUNC("gpio", 1),
-+ FUNC("wdt rst", 0),
-+};
-+
-+static const struct mtmips_pmx_func jtag_grp[] = {
-+ FUNC("gpio", 1),
-+ FUNC("jtag", 0),
-+};
-+
-+static const struct mtmips_pmx_func uart2_grp[] = {
-+ FUNC("spdif", 3),
-+ FUNC("pcm", 2),
-+ FUNC("gpio", 1),
-+ FUNC("uart", 0),
-+};
-+
-+static const struct mtmips_pmx_func uart3_grp[] = {
-+ FUNC("spdif", 3),
-+ FUNC("i2s", 2),
-+ FUNC("gpio", 1),
-+ FUNC("uart", 0),
-+};
-+
-+static const struct mtmips_pmx_func i2c_grp[] = {
-+ FUNC("gpio", 1),
-+ FUNC("i2c", 0),
-+};
-+
-+static const struct mtmips_pmx_func uart1_grp[] = {
-+ FUNC("gpio", 1),
-+ FUNC("uart", 0),
-+};
-+
-+static const struct mtmips_pmx_func gpio0_grp[] = {
-+ FUNC("gpio", 0),
-+};
-+
-+static const struct mtmips_pmx_group mt7621_pmx_data[] = {
-+ GRP_PCONF("esw int", esw_int_grp, GPIOMODE_OFS, ESWINT_SHIFT, 1,
-+ PAD_BOPT_ESWINT_OFS, 0),
-+ GRP_PCONF("sdxc", sdxc_grp, GPIOMODE_OFS, SDXC_SHIFT, GM4_MASK,
-+ PAD_SDXC_SPI_OFS, 16),
-+ GRP_PCONF("spi", spi_grp, GPIOMODE_OFS, SPI_SHIFT, GM4_MASK,
-+ PAD_SDXC_SPI_OFS, 0),
-+ GRP_PCONF("rgmii2", rgmii2_grp, GPIOMODE_OFS, RGMII2_SHIFT, 1,
-+ PAD_RGMII2_MDIO_OFS, 16),
-+ GRP("rgmii1", rgmii1_grp, GPIOMODE_OFS, RGMII1_SHIFT, 1),
-+ GRP_PCONF("mdio", mdio_grp, GPIOMODE_OFS, MDIO_SHIFT, GM4_MASK,
-+ PAD_RGMII2_MDIO_OFS, 0),
-+ GRP_PCONF("pcie reset", perst_grp, GPIOMODE_OFS, PERST_SHIFT, GM4_MASK,
-+ PAD_PERST_WDT_OFS, 16),
-+ GRP_PCONF("wdt", wdt_grp, GPIOMODE_OFS, WDT_SHIFT, GM4_MASK,
-+ PAD_PERST_WDT_OFS, 0),
-+ GRP_PCONF("jtag", jtag_grp, GPIOMODE_OFS, JTAG_SHIFT, 1,
-+ PAD_UART2_JTAG_OFS, 16),
-+ GRP_PCONF("uart2", uart2_grp, GPIOMODE_OFS, UART2_SHIFT, GM4_MASK,
-+ PAD_UART2_JTAG_OFS, 0),
-+ GRP_PCONF("uart3", uart3_grp, GPIOMODE_OFS, UART3_SHIFT, GM4_MASK,
-+ PAD_UART3_I2C_OFS, 16),
-+ GRP_PCONF("i2c", i2c_grp, GPIOMODE_OFS, I2C_SHIFT, 1,
-+ PAD_UART3_I2C_OFS, 0),
-+ GRP_PCONF("uart1", uart1_grp, GPIOMODE_OFS, UART1_SHIFT, 1,
-+ PAD_UART1_GPIO0_OFS, 16),
-+ GRP_PCONF("gpio0", gpio0_grp, GPIOMODE_OFS, GPIO0_SHIFT, 1,
-+ PAD_UART1_GPIO0_OFS, 0),
-+};
-+
-+static int mt7621_get_groups_count(struct udevice *dev)
-+{
-+ return ARRAY_SIZE(mt7621_pmx_data);
-+}
-+
-+static const char *mt7621_get_group_name(struct udevice *dev,
-+ unsigned int selector)
-+{
-+ return mt7621_pmx_data[selector].name;
-+}
-+#endif /* CONFIG_IS_ENABLED(PINMUX) */
-+
-+#if CONFIG_IS_ENABLED(PINCONF)
-+static const struct pinconf_param mt7621_conf_params[] = {
-+ { "bias-disable", PIN_CONFIG_BIAS_DISABLE, 0 },
-+ { "bias-pull-up", PIN_CONFIG_BIAS_PULL_UP, 1 },
-+ { "bias-pull-down", PIN_CONFIG_BIAS_PULL_DOWN, 1 },
-+ { "input-schmitt-enable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 1 },
-+ { "input-schmitt-disable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 0 },
-+ { "drive-strength", PIN_CONFIG_DRIVE_STRENGTH, 0 },
-+ { "slew-rate", PIN_CONFIG_SLEW_RATE, 0 },
-+};
-+
-+static const u32 mt7621_pconf_drv_strength_tbl[] = {2, 4, 6, 8};
-+
-+static int mt7621_pinconf_group_set(struct udevice *dev,
-+ unsigned int group_selector,
-+ unsigned int param, unsigned int arg)
-+{
-+ struct mt7621_pinctrl_priv *priv = dev_get_priv(dev);
-+ const struct mtmips_pmx_group *grp = &mt7621_pmx_data[group_selector];
-+ u32 clr = 0, set = 0;
-+ int i;
-+
-+ if (!grp->pconf_avail)
-+ return 0;
-+
-+ switch (param) {
-+ case PIN_CONFIG_BIAS_DISABLE:
-+ clr = PULL_UP | PULL_DOWN;
-+ break;
-+
-+ case PIN_CONFIG_BIAS_PULL_UP:
-+ clr = PULL_DOWN;
-+ set = PULL_UP;
-+ break;
-+
-+ case PIN_CONFIG_BIAS_PULL_DOWN:
-+ clr = PULL_UP;
-+ set = PULL_DOWN;
-+ break;
-+
-+ case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
-+ if (arg)
-+ set = SMT;
-+ else
-+ clr = SMT;
-+ break;
-+
-+ case PIN_CONFIG_DRIVE_STRENGTH:
-+ for (i = 0; i < ARRAY_SIZE(mt7621_pconf_drv_strength_tbl); i++)
-+ if (mt7621_pconf_drv_strength_tbl[i] == arg)
-+ break;
-+
-+ if (i >= ARRAY_SIZE(mt7621_pconf_drv_strength_tbl))
-+ return -EINVAL;
-+
-+ clr = E4_E2_M << E4_E2_S;
-+ set = i << E4_E2_S;
-+ break;
-+
-+ case PIN_CONFIG_SLEW_RATE:
-+ if (arg)
-+ set = SR;
-+ else
-+ clr = SR;
-+ break;
-+
-+ default:
-+ return -EINVAL;
-+ }
-+
-+ mtmips_pinctrl_reg_set(&priv->mp, grp->pconf_reg, grp->pconf_shift,
-+ clr, set);
-+
-+ return 0;
-+}
-+#endif
-+
-+static int mt7621_pinctrl_probe(struct udevice *dev)
-+{
-+ struct mt7621_pinctrl_priv *priv = dev_get_priv(dev);
-+ int ret = 0;
-+
-+#if CONFIG_IS_ENABLED(PINMUX)
-+ ret = mtmips_pinctrl_probe(&priv->mp, ARRAY_SIZE(mt7621_pmx_data),
-+ mt7621_pmx_data);
-+#endif /* CONFIG_IS_ENABLED(PINMUX) */
-+
-+ return ret;
-+}
-+
-+static int mt7621_pinctrl_of_to_plat(struct udevice *dev)
-+{
-+ struct mt7621_pinctrl_priv *priv = dev_get_priv(dev);
-+
-+ priv->mp.base = (void __iomem *)dev_remap_addr_index(dev, 0);
-+
-+ if (!priv->mp.base)
-+ return -EINVAL;
-+
-+ return 0;
-+}
-+
-+static const struct pinctrl_ops mt7621_pinctrl_ops = {
-+#if CONFIG_IS_ENABLED(PINMUX)
-+ .get_groups_count = mt7621_get_groups_count,
-+ .get_group_name = mt7621_get_group_name,
-+ .get_functions_count = mtmips_get_functions_count,
-+ .get_function_name = mtmips_get_function_name,
-+ .pinmux_group_set = mtmips_pinmux_group_set,
-+#endif /* CONFIG_IS_ENABLED(PINMUX) */
-+#if CONFIG_IS_ENABLED(PINCONF)
-+ .pinconf_num_params = ARRAY_SIZE(mt7621_conf_params),
-+ .pinconf_params = mt7621_conf_params,
-+ .pinconf_group_set = mt7621_pinconf_group_set,
-+#endif /* CONFIG_IS_ENABLED(PINCONF) */
-+ .set_state = pinctrl_generic_set_state,
-+};
-+
-+static const struct udevice_id mt7621_pinctrl_ids[] = {
-+ { .compatible = "mediatek,mt7621-pinctrl" },
-+ { }
-+};
-+
-+U_BOOT_DRIVER(mt7621_pinctrl) = {
-+ .name = "mt7621-pinctrl",
-+ .id = UCLASS_PINCTRL,
-+ .of_match = mt7621_pinctrl_ids,
-+ .of_to_plat = mt7621_pinctrl_of_to_plat,
-+ .ops = &mt7621_pinctrl_ops,
-+ .probe = mt7621_pinctrl_probe,
-+ .priv_auto = sizeof(struct mt7621_pinctrl_priv),
-+};
---- a/drivers/pinctrl/mtmips/pinctrl-mtmips-common.c
-+++ b/drivers/pinctrl/mtmips/pinctrl-mtmips-common.c
-@@ -13,8 +13,8 @@
-
- #include "pinctrl-mtmips-common.h"
-
--static void mtmips_pinctrl_reg_set(struct mtmips_pinctrl_priv *priv,
-- u32 reg, u32 shift, u32 mask, u32 value)
-+void mtmips_pinctrl_reg_set(struct mtmips_pinctrl_priv *priv,
-+ u32 reg, u32 shift, u32 mask, u32 value)
- {
- u32 val;
-
---- a/drivers/pinctrl/mtmips/pinctrl-mtmips-common.h
-+++ b/drivers/pinctrl/mtmips/pinctrl-mtmips-common.h
-@@ -22,6 +22,10 @@ struct mtmips_pmx_group {
- u32 shift;
- char mask;
-
-+ int pconf_avail;
-+ u32 pconf_reg;
-+ u32 pconf_shift;
-+
- int nfuncs;
- const struct mtmips_pmx_func *funcs;
- };
-@@ -42,6 +46,14 @@ struct mtmips_pinctrl_priv {
- { .name = (_name), .reg = (_reg), .shift = (_shift), .mask = (_mask), \
- .funcs = (_funcs), .nfuncs = ARRAY_SIZE(_funcs) }
-
-+#define GRP_PCONF(_name, _funcs, _reg, _shift, _mask, _pconf_reg, _pconf_shift) \
-+ { .name = (_name), .reg = (_reg), .shift = (_shift), .mask = (_mask), \
-+ .funcs = (_funcs), .nfuncs = ARRAY_SIZE(_funcs), .pconf_avail = 1, \
-+ .pconf_reg = (_pconf_reg), .pconf_shift = (_pconf_shift) }
-+
-+void mtmips_pinctrl_reg_set(struct mtmips_pinctrl_priv *priv,
-+ u32 reg, u32 shift, u32 mask, u32 value);
-+
- int mtmips_get_functions_count(struct udevice *dev);
- const char *mtmips_get_function_name(struct udevice *dev,
- unsigned int selector);
+++ /dev/null
-From ab59bb14a0efd40c12a967f73bd08ba2f27da3be Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:22:56 +0800
-Subject: [PATCH 11/25] usb: xhci-mtk: add support for MediaTek MT7621 SoC
-
-This patch makes xhci-mtk driver available for MediaTek MT7621 SoC
-
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- drivers/usb/host/Kconfig | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/usb/host/Kconfig
-+++ b/drivers/usb/host/Kconfig
-@@ -34,7 +34,7 @@ config USB_XHCI_DWC3_OF_SIMPLE
-
- config USB_XHCI_MTK
- bool "Support for MediaTek on-chip xHCI USB controller"
-- depends on ARCH_MEDIATEK
-+ depends on ARCH_MEDIATEK || SOC_MT7621
- help
- Enables support for the on-chip xHCI controller on MediaTek SoCs.
-
+++ /dev/null
-From 23c19fa476929b6e94cc7f1a55f5ed4d3ab03934 Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:23:01 +0800
-Subject: [PATCH 12/25] phy: mtk-tphy: add support for MediaTek MT7621 SoC
-
-This patch makes mtk-tphy driver available for MediaTek MT7621 SoC
-
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- drivers/phy/Kconfig | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/phy/Kconfig
-+++ b/drivers/phy/Kconfig
-@@ -266,7 +266,7 @@ config MT76X8_USB_PHY
- config PHY_MTK_TPHY
- bool "MediaTek T-PHY Driver"
- depends on PHY
-- depends on ARCH_MEDIATEK
-+ depends on ARCH_MEDIATEK || SOC_MT7621
- help
- MediaTek T-PHY driver supports usb2.0, usb3.0 ports, PCIe and
- SATA, and meanwhile supports two version T-PHY which have
+++ /dev/null
-From 34b623ccfd135e846b8464729a8b0e8df4b77a66 Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:23:08 +0800
-Subject: [PATCH 13/25] spi: add support for MediaTek MT7621 SoC
-
-This patch makes mt7621_spi driver available for MediaTek MT7621 SoC
-
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- drivers/spi/Kconfig | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/spi/Kconfig
-+++ b/drivers/spi/Kconfig
-@@ -240,7 +240,7 @@ config MT7620_SPI
-
- config MT7621_SPI
- bool "MediaTek MT7621 SPI driver"
-- depends on SOC_MT7628
-+ depends on SOC_MT7621 || SOC_MT7628
- help
- Enable the MT7621 SPI driver. This driver can be used to access
- the SPI NOR flash on platforms embedding this Ralink / MediaTek
+++ /dev/null
-From f265423a441a3bcb51e25238544adb69f74becc7 Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:23:14 +0800
-Subject: [PATCH 14/25] gpio: add support for MediaTek MT7621 SoC
-
-This patch makes mt7621_gpio driver available for MediaTek MT7621 SoC
-
-Reviewed-by: Stefan Roese <sr@denx.de>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- drivers/gpio/Kconfig | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/gpio/Kconfig
-+++ b/drivers/gpio/Kconfig
-@@ -553,7 +553,7 @@ config MT7620_GPIO
-
- config MT7621_GPIO
- bool "MediaTek MT7621 GPIO driver"
-- depends on DM_GPIO && SOC_MT7628
-+ depends on DM_GPIO && (SOC_MT7621 || SOC_MT7628)
- default y
- help
- Say yes here to support MediaTek MT7621 compatible GPIOs.
+++ /dev/null
-From eb1806fbf65c60b2ce462a0ebe39d9f9e652235a Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:23:19 +0800
-Subject: [PATCH 15/25] watchdog: add support for MediaTek MT7621 SoC
-
-This patch makes mt7621_wdt driver available for MediaTek MT7621 SoC
-
-Reviewed-by: Stefan Roese <sr@denx.de>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- drivers/watchdog/Kconfig | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/watchdog/Kconfig
-+++ b/drivers/watchdog/Kconfig
-@@ -191,7 +191,7 @@ config WDT_MT7620
-
- config WDT_MT7621
- bool "MediaTek MT7621 watchdog timer support"
-- depends on WDT && SOC_MT7628
-+ depends on WDT && (SOC_MT7621 || SOC_MT7628)
- help
- Select this to enable Ralink / Mediatek watchdog timer,
- which can be found on some MediaTek chips.
+++ /dev/null
-From 4339ec44313e85dd1f6d3d708dd2e594855ce25d Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:23:26 +0800
-Subject: [PATCH 16/25] mmc: mediatek: add support for MediaTek MT7621 SoC
-
-This patch adds SDXC support for MediaTek MT7621 SoC
-
-Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- drivers/mmc/mtk-sd.c | 13 +++++++++++++
- 1 file changed, 13 insertions(+)
-
---- a/drivers/mmc/mtk-sd.c
-+++ b/drivers/mmc/mtk-sd.c
-@@ -1761,6 +1761,18 @@ static const struct msdc_compatible mt76
- .default_pad_dly = true,
- };
-
-+static const struct msdc_compatible mt7621_compat = {
-+ .clk_div_bits = 8,
-+ .pad_tune0 = false,
-+ .async_fifo = true,
-+ .data_tune = true,
-+ .busy_check = false,
-+ .stop_clk_fix = false,
-+ .enhance_rx = false,
-+ .builtin_pad_ctrl = true,
-+ .default_pad_dly = true,
-+};
-+
- static const struct msdc_compatible mt7622_compat = {
- .clk_div_bits = 12,
- .pad_tune0 = true,
-@@ -1809,6 +1821,7 @@ static const struct msdc_compatible mt81
-
- static const struct udevice_id msdc_ids[] = {
- { .compatible = "mediatek,mt7620-mmc", .data = (ulong)&mt7620_compat },
-+ { .compatible = "mediatek,mt7621-mmc", .data = (ulong)&mt7621_compat },
- { .compatible = "mediatek,mt7622-mmc", .data = (ulong)&mt7622_compat },
- { .compatible = "mediatek,mt7623-mmc", .data = (ulong)&mt7623_compat },
- { .compatible = "mediatek,mt8512-mmc", .data = (ulong)&mt8512_compat },
+++ /dev/null
-From 391785398f61c85e6b55b1e9edbab94e3ba1b783 Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:23:31 +0800
-Subject: [PATCH 17/25] net: mediatek: remap iobase address
-
-The iobase address from dts node is actually physical address. It's
-identical to the virtual address in ARM platform. This is ok because this
-driver was used only by ARM platforms (mt7622/mt7623 ...).
-
-But now this driver will be used by mt7621 which is a MIPS SoC. For MIPS
-platform the physical address space is mapped to KSEG0 and KSEG1 and this
-makes the virtual address apparently not idential to its physical address.
-
-To solve this issue, this patch replaces dev_read_addr with dev_remap_addr
-to get the remapped iobase address.
-
-Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- drivers/net/mtk_eth.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/net/mtk_eth.c
-+++ b/drivers/net/mtk_eth.c
-@@ -1419,7 +1419,7 @@ static int mtk_eth_of_to_plat(struct ude
-
- priv->soc = dev_get_driver_data(dev);
-
-- pdata->iobase = dev_read_addr(dev);
-+ pdata->iobase = (phys_addr_t)dev_remap_addr(dev);
-
- /* get corresponding ethsys phandle */
- ret = dev_read_phandle_with_args(dev, "mediatek,ethsys", NULL, 0, 0,
+++ /dev/null
-From 955cc76d8074df943d59d559895007f91de8eed5 Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:23:37 +0800
-Subject: [PATCH 18/25] net: mediatek: use regmap api to modify ethsys
- registers
-
-The address returned by regmap_get_range() is not remapped. Directly r/w
-to this address is ok for ARM platforms since it's idential to the virtual
-address.
-
-But for MIPS platform only virtual address should be used for access.
-To solve this issue, the regmap api regmap_read/regmap_write should be used
-since they will remap address before accessing.
-
-Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- drivers/net/mtk_eth.c | 22 +++++++++++-----------
- 1 file changed, 11 insertions(+), 11 deletions(-)
-
---- a/drivers/net/mtk_eth.c
-+++ b/drivers/net/mtk_eth.c
-@@ -159,9 +159,10 @@ struct mtk_eth_priv {
-
- void __iomem *fe_base;
- void __iomem *gmac_base;
-- void __iomem *ethsys_base;
- void __iomem *sgmii_base;
-
-+ struct regmap *ethsys_regmap;
-+
- struct mii_dev *mdio_bus;
- int (*mii_read)(struct mtk_eth_priv *priv, u8 phy, u8 reg);
- int (*mii_write)(struct mtk_eth_priv *priv, u8 phy, u8 reg, u16 val);
-@@ -233,7 +234,12 @@ static void mtk_gmac_rmw(struct mtk_eth_
- static void mtk_ethsys_rmw(struct mtk_eth_priv *priv, u32 reg, u32 clr,
- u32 set)
- {
-- clrsetbits_le32(priv->ethsys_base + reg, clr, set);
-+ uint val;
-+
-+ regmap_read(priv->ethsys_regmap, reg, &val);
-+ val &= ~clr;
-+ val |= set;
-+ regmap_write(priv->ethsys_regmap, reg, val);
- }
-
- /* Direct MDIO clause 22/45 access via SoC */
-@@ -1427,15 +1433,9 @@ static int mtk_eth_of_to_plat(struct ude
- if (ret)
- return ret;
-
-- regmap = syscon_node_to_regmap(args.node);
-- if (IS_ERR(regmap))
-- return PTR_ERR(regmap);
--
-- priv->ethsys_base = regmap_get_range(regmap, 0);
-- if (!priv->ethsys_base) {
-- dev_err(dev, "Unable to find ethsys\n");
-- return -ENODEV;
-- }
-+ priv->ethsys_regmap = syscon_node_to_regmap(args.node);
-+ if (IS_ERR(priv->ethsys_regmap))
-+ return PTR_ERR(priv->ethsys_regmap);
-
- /* Reset controllers */
- ret = reset_get_by_name(dev, "fe", &priv->rst_fe);
+++ /dev/null
-From 7237a6a0c020c05bb819774391154b40b2cfaabd Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:23:42 +0800
-Subject: [PATCH 19/25] net: mediatek: add support for MediaTek MT7621 SoC
-
-This patch adds GMAC support for MediaTek MT7621 SoC.
-MT7621 has the same GMAC/Switch configuration as MT7623.
-
-Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- drivers/net/mtk_eth.c | 21 +++++++++++++++------
- 1 file changed, 15 insertions(+), 6 deletions(-)
-
---- a/drivers/net/mtk_eth.c
-+++ b/drivers/net/mtk_eth.c
-@@ -145,7 +145,8 @@ enum mtk_switch {
- enum mtk_soc {
- SOC_MT7623,
- SOC_MT7629,
-- SOC_MT7622
-+ SOC_MT7622,
-+ SOC_MT7621
- };
-
- struct mtk_eth_priv {
-@@ -675,12 +676,18 @@ static int mt7530_pad_clk_setup(struct m
- static int mt7530_setup(struct mtk_eth_priv *priv)
- {
- u16 phy_addr, phy_val;
-- u32 val;
-+ u32 val, txdrv;
- int i;
-
-- /* Select 250MHz clk for RGMII mode */
-- mtk_ethsys_rmw(priv, ETHSYS_CLKCFG0_REG,
-- ETHSYS_TRGMII_CLK_SEL362_5, 0);
-+ if (priv->soc != SOC_MT7621) {
-+ /* Select 250MHz clk for RGMII mode */
-+ mtk_ethsys_rmw(priv, ETHSYS_CLKCFG0_REG,
-+ ETHSYS_TRGMII_CLK_SEL362_5, 0);
-+
-+ txdrv = 8;
-+ } else {
-+ txdrv = 4;
-+ }
-
- /* Modify HWTRAP first to allow direct access to internal PHYs */
- mt753x_reg_read(priv, HWTRAP_REG, &val);
-@@ -738,7 +745,8 @@ static int mt7530_setup(struct mtk_eth_p
- /* Lower Tx Driving for TRGMII path */
- for (i = 0 ; i < NUM_TRGMII_CTRL ; i++)
- mt753x_reg_write(priv, MT7530_TRGMII_TD_ODT(i),
-- (8 << TD_DM_DRVP_S) | (8 << TD_DM_DRVN_S));
-+ (txdrv << TD_DM_DRVP_S) |
-+ (txdrv << TD_DM_DRVN_S));
-
- for (i = 0 ; i < NUM_TRGMII_CTRL; i++)
- mt753x_reg_rmw(priv, MT7530_TRGMII_RD(i), RD_TAP_M, 16);
-@@ -1540,6 +1548,7 @@ static const struct udevice_id mtk_eth_i
- { .compatible = "mediatek,mt7629-eth", .data = SOC_MT7629 },
- { .compatible = "mediatek,mt7623-eth", .data = SOC_MT7623 },
- { .compatible = "mediatek,mt7622-eth", .data = SOC_MT7622 },
-+ { .compatible = "mediatek,mt7621-eth", .data = SOC_MT7621 },
- {}
- };
-
+++ /dev/null
-From 8d94833f13ccd7e1dfea605cfdf9a8eb53505515 Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:23:47 +0800
-Subject: [PATCH 20/25] nand: raw: add support for MediaTek MT7621 SoC
-
-This patch adds NAND flash controller driver for MediaTek MT7621 SoC.
-The NAND flash controller of MT7621 supports only SLC NAND flashes.
-It supports 4~12 bits correction with maximum 4KB page size.
-
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- drivers/mtd/nand/raw/Kconfig | 17 +-
- drivers/mtd/nand/raw/Makefile | 2 +
- drivers/mtd/nand/raw/mt7621_nand.c | 1205 ++++++++++++++++++++++++
- drivers/mtd/nand/raw/mt7621_nand.h | 29 +
- drivers/mtd/nand/raw/mt7621_nand_spl.c | 237 +++++
- 5 files changed, 1488 insertions(+), 2 deletions(-)
- create mode 100644 drivers/mtd/nand/raw/mt7621_nand.c
- create mode 100644 drivers/mtd/nand/raw/mt7621_nand.h
- create mode 100644 drivers/mtd/nand/raw/mt7621_nand_spl.c
-
---- a/drivers/mtd/nand/raw/Kconfig
-+++ b/drivers/mtd/nand/raw/Kconfig
-@@ -521,12 +521,25 @@ config TEGRA_NAND
- help
- Enables support for NAND Flash chips on Tegra SoCs platforms.
-
-+config NAND_MT7621
-+ bool "Support for MediaTek MT7621 NAND flash controller"
-+ depends on SOC_MT7621
-+ select SYS_NAND_SELF_INIT
-+ select SPL_SYS_NAND_SELF_INIT
-+ imply CMD_NAND
-+ help
-+ This enables NAND driver for the NAND flash controller on MediaTek
-+ MT7621 platform.
-+ The controller supports 4~12 bits correction per 512 bytes with a
-+ maximum 4KB page size.
-+
- comment "Generic NAND options"
-
- config SYS_NAND_BLOCK_SIZE
- hex "NAND chip eraseblock size"
- depends on ARCH_SUNXI || SPL_NAND_SUPPORT || TPL_NAND_SUPPORT
-- depends on !NAND_MXS && !NAND_DENALI_DT && !NAND_LPC32XX_MLC && !NAND_FSL_IFC
-+ depends on !NAND_MXS && !NAND_DENALI_DT && !NAND_LPC32XX_MLC && \
-+ !NAND_FSL_IFC && !NAND_MT7621
- help
- Number of data bytes in one eraseblock for the NAND chip on the
- board. This is the multiple of NAND_PAGE_SIZE and the number of
-@@ -551,7 +564,7 @@ config SYS_NAND_PAGE_SIZE
- depends on ARCH_SUNXI || NAND_OMAP_GPMC || NAND_LPC32XX_SLC || \
- SPL_NAND_SIMPLE || (NAND_MXC && SPL_NAND_SUPPORT) || \
- (NAND_ATMEL && SPL_NAND_SUPPORT) || SPL_GENERATE_ATMEL_PMECC_HEADER
-- depends on !NAND_MXS && !NAND_DENALI_DT && !NAND_LPC32XX_MLC
-+ depends on !NAND_MXS && !NAND_DENALI_DT && !NAND_LPC32XX_MLC && !NAND_MT7621
- help
- Number of data bytes in one page for the NAND chip on the
- board, not including the OOB area.
---- a/drivers/mtd/nand/raw/Makefile
-+++ b/drivers/mtd/nand/raw/Makefile
-@@ -72,6 +72,7 @@ obj-$(CONFIG_NAND_ZYNQ) += zynq_nand.o
- obj-$(CONFIG_NAND_STM32_FMC2) += stm32_fmc2_nand.o
- obj-$(CONFIG_CORTINA_NAND) += cortina_nand.o
- obj-$(CONFIG_ROCKCHIP_NAND) += rockchip_nfc.o
-+obj-$(CONFIG_NAND_MT7621) += mt7621_nand.o
-
- else # minimal SPL drivers
-
-@@ -80,5 +81,6 @@ obj-$(CONFIG_NAND_FSL_IFC) += fsl_ifc_sp
- obj-$(CONFIG_NAND_MXC) += mxc_nand_spl.o
- obj-$(CONFIG_NAND_MXS) += mxs_nand_spl.o mxs_nand.o
- obj-$(CONFIG_NAND_SUNXI) += sunxi_nand_spl.o
-+obj-$(CONFIG_NAND_MT7621) += mt7621_nand_spl.o mt7621_nand.o
-
- endif # drivers
---- /dev/null
-+++ b/drivers/mtd/nand/raw/mt7621_nand.c
-@@ -0,0 +1,1205 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <log.h>
-+#include <nand.h>
-+#include <malloc.h>
-+#include <asm/addrspace.h>
-+#include <linux/io.h>
-+#include <linux/iopoll.h>
-+#include <linux/sizes.h>
-+#include <linux/bitops.h>
-+#include <linux/bitfield.h>
-+#include "mt7621_nand.h"
-+
-+/* NFI core registers */
-+#define NFI_CNFG 0x000
-+#define CNFG_OP_MODE GENMASK(14, 12)
-+#define CNFG_OP_CUSTOM 6
-+#define CNFG_AUTO_FMT_EN BIT(9)
-+#define CNFG_HW_ECC_EN BIT(8)
-+#define CNFG_BYTE_RW BIT(6)
-+#define CNFG_READ_MODE BIT(1)
-+
-+#define NFI_PAGEFMT 0x004
-+#define PAGEFMT_FDM_ECC GENMASK(15, 12)
-+#define PAGEFMT_FDM GENMASK(11, 8)
-+#define PAGEFMT_SPARE GENMASK(5, 4)
-+#define PAGEFMT_PAGE GENMASK(1, 0)
-+
-+#define NFI_CON 0x008
-+#define CON_NFI_SEC GENMASK(15, 12)
-+#define CON_NFI_BWR BIT(9)
-+#define CON_NFI_BRD BIT(8)
-+#define CON_NFI_RST BIT(1)
-+#define CON_FIFO_FLUSH BIT(0)
-+
-+#define NFI_ACCCON 0x00c
-+#define ACCCON_POECS GENMASK(31, 28)
-+#define ACCCON_POECS_DEF 3
-+#define ACCCON_PRECS GENMASK(27, 22)
-+#define ACCCON_PRECS_DEF 3
-+#define ACCCON_C2R GENMASK(21, 16)
-+#define ACCCON_C2R_DEF 7
-+#define ACCCON_W2R GENMASK(15, 12)
-+#define ACCCON_W2R_DEF 7
-+#define ACCCON_WH GENMASK(11, 8)
-+#define ACCCON_WH_DEF 15
-+#define ACCCON_WST GENMASK(7, 4)
-+#define ACCCON_WST_DEF 15
-+#define ACCCON_WST_MIN 3
-+#define ACCCON_RLT GENMASK(3, 0)
-+#define ACCCON_RLT_DEF 15
-+#define ACCCON_RLT_MIN 3
-+
-+#define NFI_CMD 0x020
-+
-+#define NFI_ADDRNOB 0x030
-+#define ADDR_ROW_NOB GENMASK(6, 4)
-+#define ADDR_COL_NOB GENMASK(2, 0)
-+
-+#define NFI_COLADDR 0x034
-+#define NFI_ROWADDR 0x038
-+
-+#define NFI_STRDATA 0x040
-+#define STR_DATA BIT(0)
-+
-+#define NFI_CNRNB 0x044
-+#define CB2R_TIME GENMASK(7, 4)
-+#define STR_CNRNB BIT(0)
-+
-+#define NFI_DATAW 0x050
-+#define NFI_DATAR 0x054
-+
-+#define NFI_PIO_DIRDY 0x058
-+#define PIO_DIRDY BIT(0)
-+
-+#define NFI_STA 0x060
-+#define STA_NFI_FSM GENMASK(19, 16)
-+#define STA_FSM_CUSTOM_DATA 14
-+#define STA_BUSY BIT(8)
-+#define STA_ADDR BIT(1)
-+#define STA_CMD BIT(0)
-+
-+#define NFI_ADDRCNTR 0x070
-+#define SEC_CNTR GENMASK(15, 12)
-+#define SEC_ADDR GENMASK(9, 0)
-+
-+#define NFI_CSEL 0x090
-+#define CSEL GENMASK(1, 0)
-+
-+#define NFI_FDM0L 0x0a0
-+#define NFI_FDML(n) (0x0a0 + ((n) << 3))
-+
-+#define NFI_FDM0M 0x0a4
-+#define NFI_FDMM(n) (0x0a4 + ((n) << 3))
-+
-+#define NFI_MASTER_STA 0x210
-+#define MAS_ADDR GENMASK(11, 9)
-+#define MAS_RD GENMASK(8, 6)
-+#define MAS_WR GENMASK(5, 3)
-+#define MAS_RDDLY GENMASK(2, 0)
-+
-+/* ECC engine registers */
-+#define ECC_ENCCON 0x000
-+#define ENC_EN BIT(0)
-+
-+#define ECC_ENCCNFG 0x004
-+#define ENC_CNFG_MSG GENMASK(28, 16)
-+#define ENC_MODE GENMASK(5, 4)
-+#define ENC_MODE_NFI 1
-+#define ENC_TNUM GENMASK(2, 0)
-+
-+#define ECC_ENCIDLE 0x00c
-+#define ENC_IDLE BIT(0)
-+
-+#define ECC_DECCON 0x100
-+#define DEC_EN BIT(0)
-+
-+#define ECC_DECCNFG 0x104
-+#define DEC_EMPTY_EN BIT(31)
-+#define DEC_CS GENMASK(28, 16)
-+#define DEC_CON GENMASK(13, 12)
-+#define DEC_CON_EL 2
-+#define DEC_MODE GENMASK(5, 4)
-+#define DEC_MODE_NFI 1
-+#define DEC_TNUM GENMASK(2, 0)
-+
-+#define ECC_DECIDLE 0x10c
-+#define DEC_IDLE BIT(1)
-+
-+#define ECC_DECENUM 0x114
-+#define ERRNUM_S 2
-+#define ERRNUM_M GENMASK(3, 0)
-+
-+#define ECC_DECDONE 0x118
-+#define DEC_DONE7 BIT(7)
-+#define DEC_DONE6 BIT(6)
-+#define DEC_DONE5 BIT(5)
-+#define DEC_DONE4 BIT(4)
-+#define DEC_DONE3 BIT(3)
-+#define DEC_DONE2 BIT(2)
-+#define DEC_DONE1 BIT(1)
-+#define DEC_DONE0 BIT(0)
-+
-+#define ECC_DECEL(n) (0x11c + (n) * 4)
-+#define DEC_EL_ODD_S 16
-+#define DEC_EL_M 0x1fff
-+#define DEC_EL_BYTE_POS_S 3
-+#define DEC_EL_BIT_POS_M GENMASK(2, 0)
-+
-+#define ECC_FDMADDR 0x13c
-+
-+/* ENCIDLE and DECIDLE */
-+#define ECC_IDLE BIT(0)
-+
-+#define ACCTIMING(tpoecs, tprecs, tc2r, tw2r, twh, twst, trlt) \
-+ (FIELD_PREP(ACCCON_POECS, tpoecs) | \
-+ FIELD_PREP(ACCCON_PRECS, tprecs) | \
-+ FIELD_PREP(ACCCON_C2R, tc2r) | \
-+ FIELD_PREP(ACCCON_W2R, tw2r) | \
-+ FIELD_PREP(ACCCON_WH, twh) | \
-+ FIELD_PREP(ACCCON_WST, twst) | \
-+ FIELD_PREP(ACCCON_RLT, trlt))
-+
-+#define MASTER_STA_MASK (MAS_ADDR | MAS_RD | MAS_WR | \
-+ MAS_RDDLY)
-+#define NFI_RESET_TIMEOUT 1000000
-+#define NFI_CORE_TIMEOUT 500000
-+#define ECC_ENGINE_TIMEOUT 500000
-+
-+#define ECC_SECTOR_SIZE 512
-+#define ECC_PARITY_BITS 13
-+
-+#define NFI_FDM_SIZE 8
-+
-+/* Register base */
-+#define NFI_BASE 0x1e003000
-+#define NFI_ECC_BASE 0x1e003800
-+
-+static struct mt7621_nfc nfc_dev;
-+
-+static const u16 mt7621_nfi_page_size[] = { SZ_512, SZ_2K, SZ_4K };
-+static const u8 mt7621_nfi_spare_size[] = { 16, 26, 27, 28 };
-+static const u8 mt7621_ecc_strength[] = { 4, 6, 8, 10, 12 };
-+
-+static inline u32 nfi_read32(struct mt7621_nfc *nfc, u32 reg)
-+{
-+ return readl(nfc->nfi_regs + reg);
-+}
-+
-+static inline void nfi_write32(struct mt7621_nfc *nfc, u32 reg, u32 val)
-+{
-+ writel(val, nfc->nfi_regs + reg);
-+}
-+
-+static inline u16 nfi_read16(struct mt7621_nfc *nfc, u32 reg)
-+{
-+ return readw(nfc->nfi_regs + reg);
-+}
-+
-+static inline void nfi_write16(struct mt7621_nfc *nfc, u32 reg, u16 val)
-+{
-+ writew(val, nfc->nfi_regs + reg);
-+}
-+
-+static inline void ecc_write16(struct mt7621_nfc *nfc, u32 reg, u16 val)
-+{
-+ writew(val, nfc->ecc_regs + reg);
-+}
-+
-+static inline u32 ecc_read32(struct mt7621_nfc *nfc, u32 reg)
-+{
-+ return readl(nfc->ecc_regs + reg);
-+}
-+
-+static inline void ecc_write32(struct mt7621_nfc *nfc, u32 reg, u32 val)
-+{
-+ return writel(val, nfc->ecc_regs + reg);
-+}
-+
-+static inline u8 *oob_fdm_ptr(struct nand_chip *nand, int sect)
-+{
-+ return nand->oob_poi + sect * NFI_FDM_SIZE;
-+}
-+
-+static inline u8 *oob_ecc_ptr(struct mt7621_nfc *nfc, int sect)
-+{
-+ struct nand_chip *nand = &nfc->nand;
-+
-+ return nand->oob_poi + nand->ecc.steps * NFI_FDM_SIZE +
-+ sect * (nfc->spare_per_sector - NFI_FDM_SIZE);
-+}
-+
-+static inline u8 *page_data_ptr(struct nand_chip *nand, const u8 *buf,
-+ int sect)
-+{
-+ return (u8 *)buf + sect * nand->ecc.size;
-+}
-+
-+static int mt7621_ecc_wait_idle(struct mt7621_nfc *nfc, u32 reg)
-+{
-+ u32 val;
-+ int ret;
-+
-+ ret = readw_poll_timeout(nfc->ecc_regs + reg, val, val & ECC_IDLE,
-+ ECC_ENGINE_TIMEOUT);
-+ if (ret) {
-+ pr_warn("ECC engine timed out entering idle mode\n");
-+ return -EIO;
-+ }
-+
-+ return 0;
-+}
-+
-+static int mt7621_ecc_decoder_wait_done(struct mt7621_nfc *nfc, u32 sect)
-+{
-+ u32 val;
-+ int ret;
-+
-+ ret = readw_poll_timeout(nfc->ecc_regs + ECC_DECDONE, val,
-+ val & (1 << sect), ECC_ENGINE_TIMEOUT);
-+ if (ret) {
-+ pr_warn("ECC decoder for sector %d timed out\n", sect);
-+ return -ETIMEDOUT;
-+ }
-+
-+ return 0;
-+}
-+
-+static void mt7621_ecc_encoder_op(struct mt7621_nfc *nfc, bool enable)
-+{
-+ mt7621_ecc_wait_idle(nfc, ECC_ENCIDLE);
-+ ecc_write16(nfc, ECC_ENCCON, enable ? ENC_EN : 0);
-+}
-+
-+static void mt7621_ecc_decoder_op(struct mt7621_nfc *nfc, bool enable)
-+{
-+ mt7621_ecc_wait_idle(nfc, ECC_DECIDLE);
-+ ecc_write16(nfc, ECC_DECCON, enable ? DEC_EN : 0);
-+}
-+
-+static int mt7621_ecc_correct_check(struct mt7621_nfc *nfc, u8 *sector_buf,
-+ u8 *fdm_buf, u32 sect)
-+{
-+ struct nand_chip *nand = &nfc->nand;
-+ u32 decnum, num_error_bits, fdm_end_bits;
-+ u32 error_locations, error_bit_loc;
-+ u32 error_byte_pos, error_bit_pos;
-+ int bitflips = 0;
-+ u32 i;
-+
-+ decnum = ecc_read32(nfc, ECC_DECENUM);
-+ num_error_bits = (decnum >> (sect << ERRNUM_S)) & ERRNUM_M;
-+ fdm_end_bits = (nand->ecc.size + NFI_FDM_SIZE) << 3;
-+
-+ if (!num_error_bits)
-+ return 0;
-+
-+ if (num_error_bits == ERRNUM_M)
-+ return -1;
-+
-+ for (i = 0; i < num_error_bits; i++) {
-+ error_locations = ecc_read32(nfc, ECC_DECEL(i / 2));
-+ error_bit_loc = (error_locations >> ((i % 2) * DEC_EL_ODD_S)) &
-+ DEC_EL_M;
-+ error_byte_pos = error_bit_loc >> DEC_EL_BYTE_POS_S;
-+ error_bit_pos = error_bit_loc & DEC_EL_BIT_POS_M;
-+
-+ if (error_bit_loc < (nand->ecc.size << 3)) {
-+ if (sector_buf) {
-+ sector_buf[error_byte_pos] ^=
-+ (1 << error_bit_pos);
-+ }
-+ } else if (error_bit_loc < fdm_end_bits) {
-+ if (fdm_buf) {
-+ fdm_buf[error_byte_pos - nand->ecc.size] ^=
-+ (1 << error_bit_pos);
-+ }
-+ }
-+
-+ bitflips++;
-+ }
-+
-+ return bitflips;
-+}
-+
-+static int mt7621_nfc_wait_write_completion(struct mt7621_nfc *nfc,
-+ struct nand_chip *nand)
-+{
-+ u16 val;
-+ int ret;
-+
-+ ret = readw_poll_timeout(nfc->nfi_regs + NFI_ADDRCNTR, val,
-+ FIELD_GET(SEC_CNTR, val) >= nand->ecc.steps,
-+ NFI_CORE_TIMEOUT);
-+
-+ if (ret) {
-+ pr_warn("NFI core write operation timed out\n");
-+ return -ETIMEDOUT;
-+ }
-+
-+ return ret;
-+}
-+
-+static void mt7621_nfc_hw_reset(struct mt7621_nfc *nfc)
-+{
-+ u32 val;
-+ int ret;
-+
-+ /* reset all registers and force the NFI master to terminate */
-+ nfi_write16(nfc, NFI_CON, CON_FIFO_FLUSH | CON_NFI_RST);
-+
-+ /* wait for the master to finish the last transaction */
-+ ret = readw_poll_timeout(nfc->nfi_regs + NFI_MASTER_STA, val,
-+ !(val & MASTER_STA_MASK), NFI_RESET_TIMEOUT);
-+ if (ret) {
-+ pr_warn("Failed to reset NFI master in %dms\n",
-+ NFI_RESET_TIMEOUT);
-+ }
-+
-+ /* ensure any status register affected by the NFI master is reset */
-+ nfi_write16(nfc, NFI_CON, CON_FIFO_FLUSH | CON_NFI_RST);
-+ nfi_write16(nfc, NFI_STRDATA, 0);
-+}
-+
-+static inline void mt7621_nfc_hw_init(struct mt7621_nfc *nfc)
-+{
-+ u32 acccon;
-+
-+ /*
-+ * CNRNB: nand ready/busy register
-+ * -------------------------------
-+ * 7:4: timeout register for polling the NAND busy/ready signal
-+ * 0 : poll the status of the busy/ready signal after [7:4]*16 cycles.
-+ */
-+ nfi_write16(nfc, NFI_CNRNB, CB2R_TIME | STR_CNRNB);
-+
-+ mt7621_nfc_hw_reset(nfc);
-+
-+ /* Apply default access timing */
-+ acccon = ACCTIMING(ACCCON_POECS_DEF, ACCCON_PRECS_DEF, ACCCON_C2R_DEF,
-+ ACCCON_W2R_DEF, ACCCON_WH_DEF, ACCCON_WST_DEF,
-+ ACCCON_RLT_DEF);
-+
-+ nfi_write32(nfc, NFI_ACCCON, acccon);
-+}
-+
-+static int mt7621_nfc_send_command(struct mt7621_nfc *nfc, u8 command)
-+{
-+ u32 val;
-+ int ret;
-+
-+ nfi_write32(nfc, NFI_CMD, command);
-+
-+ ret = readl_poll_timeout(nfc->nfi_regs + NFI_STA, val, !(val & STA_CMD),
-+ NFI_CORE_TIMEOUT);
-+ if (ret) {
-+ pr_warn("NFI core timed out entering command mode\n");
-+ return -EIO;
-+ }
-+
-+ return 0;
-+}
-+
-+static int mt7621_nfc_send_address_byte(struct mt7621_nfc *nfc, int addr)
-+{
-+ u32 val;
-+ int ret;
-+
-+ nfi_write32(nfc, NFI_COLADDR, addr);
-+ nfi_write32(nfc, NFI_ROWADDR, 0);
-+ nfi_write16(nfc, NFI_ADDRNOB, 1);
-+
-+ ret = readl_poll_timeout(nfc->nfi_regs + NFI_STA, val,
-+ !(val & STA_ADDR), NFI_CORE_TIMEOUT);
-+ if (ret) {
-+ pr_warn("NFI core timed out entering address mode\n");
-+ return -EIO;
-+ }
-+
-+ return 0;
-+}
-+
-+static void mt7621_nfc_cmd_ctrl(struct mtd_info *mtd, int dat,
-+ unsigned int ctrl)
-+{
-+ struct mt7621_nfc *nfc = nand_get_controller_data(mtd_to_nand(mtd));
-+
-+ if (ctrl & NAND_ALE) {
-+ mt7621_nfc_send_address_byte(nfc, dat & 0xff);
-+ } else if (ctrl & NAND_CLE) {
-+ mt7621_nfc_hw_reset(nfc);
-+ nfi_write16(nfc, NFI_CNFG,
-+ FIELD_PREP(CNFG_OP_MODE, CNFG_OP_CUSTOM));
-+ mt7621_nfc_send_command(nfc, dat);
-+ }
-+}
-+
-+static int mt7621_nfc_dev_ready(struct mtd_info *mtd)
-+{
-+ struct mt7621_nfc *nfc = nand_get_controller_data(mtd_to_nand(mtd));
-+
-+ if (nfi_read32(nfc, NFI_STA) & STA_BUSY)
-+ return 0;
-+
-+ return 1;
-+}
-+
-+static void mt7621_nfc_select_chip(struct mtd_info *mtd, int chipnr)
-+{
-+ struct mt7621_nfc *nfc = nand_get_controller_data(mtd_to_nand(mtd));
-+
-+ nfi_write16(nfc, NFI_CSEL, 0);
-+}
-+
-+static void mt7621_nfc_wait_pio_ready(struct mt7621_nfc *nfc)
-+{
-+ int ret;
-+ u16 val;
-+
-+ ret = readw_poll_timeout(nfc->nfi_regs + NFI_PIO_DIRDY, val,
-+ val & PIO_DIRDY, NFI_CORE_TIMEOUT);
-+ if (ret < 0)
-+ pr_err("NFI core PIO mode not ready\n");
-+}
-+
-+static u32 mt7621_nfc_pio_read(struct mt7621_nfc *nfc, bool br)
-+{
-+ u32 reg, fsm;
-+
-+ /* after each byte read, the NFI_STA reg is reset by the hardware */
-+ reg = nfi_read32(nfc, NFI_STA);
-+ fsm = FIELD_GET(STA_NFI_FSM, reg);
-+
-+ if (fsm != STA_FSM_CUSTOM_DATA) {
-+ reg = nfi_read16(nfc, NFI_CNFG);
-+ reg |= CNFG_READ_MODE | CNFG_BYTE_RW;
-+ if (!br)
-+ reg &= ~CNFG_BYTE_RW;
-+ nfi_write16(nfc, NFI_CNFG, reg);
-+
-+ /*
-+ * set to max sector to allow the HW to continue reading over
-+ * unaligned accesses
-+ */
-+ nfi_write16(nfc, NFI_CON, CON_NFI_SEC | CON_NFI_BRD);
-+
-+ /* trigger to fetch data */
-+ nfi_write16(nfc, NFI_STRDATA, STR_DATA);
-+ }
-+
-+ mt7621_nfc_wait_pio_ready(nfc);
-+
-+ return nfi_read32(nfc, NFI_DATAR);
-+}
-+
-+static void mt7621_nfc_read_data(struct mt7621_nfc *nfc, u8 *buf, u32 len)
-+{
-+ while (((uintptr_t)buf & 3) && len) {
-+ *buf = mt7621_nfc_pio_read(nfc, true);
-+ buf++;
-+ len--;
-+ }
-+
-+ while (len >= 4) {
-+ *(u32 *)buf = mt7621_nfc_pio_read(nfc, false);
-+ buf += 4;
-+ len -= 4;
-+ }
-+
-+ while (len) {
-+ *buf = mt7621_nfc_pio_read(nfc, true);
-+ buf++;
-+ len--;
-+ }
-+}
-+
-+static void mt7621_nfc_read_data_discard(struct mt7621_nfc *nfc, u32 len)
-+{
-+ while (len >= 4) {
-+ mt7621_nfc_pio_read(nfc, false);
-+ len -= 4;
-+ }
-+
-+ while (len) {
-+ mt7621_nfc_pio_read(nfc, true);
-+ len--;
-+ }
-+}
-+
-+static void mt7621_nfc_pio_write(struct mt7621_nfc *nfc, u32 val, bool bw)
-+{
-+ u32 reg, fsm;
-+
-+ reg = nfi_read32(nfc, NFI_STA);
-+ fsm = FIELD_GET(STA_NFI_FSM, reg);
-+
-+ if (fsm != STA_FSM_CUSTOM_DATA) {
-+ reg = nfi_read16(nfc, NFI_CNFG);
-+ reg &= ~(CNFG_READ_MODE | CNFG_BYTE_RW);
-+ if (bw)
-+ reg |= CNFG_BYTE_RW;
-+ nfi_write16(nfc, NFI_CNFG, reg);
-+
-+ nfi_write16(nfc, NFI_CON, CON_NFI_SEC | CON_NFI_BWR);
-+ nfi_write16(nfc, NFI_STRDATA, STR_DATA);
-+ }
-+
-+ mt7621_nfc_wait_pio_ready(nfc);
-+ nfi_write32(nfc, NFI_DATAW, val);
-+}
-+
-+static void mt7621_nfc_write_data(struct mt7621_nfc *nfc, const u8 *buf,
-+ u32 len)
-+{
-+ while (((uintptr_t)buf & 3) && len) {
-+ mt7621_nfc_pio_write(nfc, *buf, true);
-+ buf++;
-+ len--;
-+ }
-+
-+ while (len >= 4) {
-+ mt7621_nfc_pio_write(nfc, *(const u32 *)buf, false);
-+ buf += 4;
-+ len -= 4;
-+ }
-+
-+ while (len) {
-+ mt7621_nfc_pio_write(nfc, *buf, true);
-+ buf++;
-+ len--;
-+ }
-+}
-+
-+static void mt7621_nfc_write_data_empty(struct mt7621_nfc *nfc, u32 len)
-+{
-+ while (len >= 4) {
-+ mt7621_nfc_pio_write(nfc, 0xffffffff, false);
-+ len -= 4;
-+ }
-+
-+ while (len) {
-+ mt7621_nfc_pio_write(nfc, 0xff, true);
-+ len--;
-+ }
-+}
-+
-+static void mt7621_nfc_write_byte(struct mtd_info *mtd, u8 byte)
-+{
-+ struct mt7621_nfc *nfc = nand_get_controller_data(mtd_to_nand(mtd));
-+
-+ mt7621_nfc_pio_write(nfc, byte, true);
-+}
-+
-+static void mt7621_nfc_write_buf(struct mtd_info *mtd, const u8 *buf, int len)
-+{
-+ struct mt7621_nfc *nfc = nand_get_controller_data(mtd_to_nand(mtd));
-+
-+ return mt7621_nfc_write_data(nfc, buf, len);
-+}
-+
-+static u8 mt7621_nfc_read_byte(struct mtd_info *mtd)
-+{
-+ struct mt7621_nfc *nfc = nand_get_controller_data(mtd_to_nand(mtd));
-+
-+ return mt7621_nfc_pio_read(nfc, true);
-+}
-+
-+static void mt7621_nfc_read_buf(struct mtd_info *mtd, u8 *buf, int len)
-+{
-+ struct mt7621_nfc *nfc = nand_get_controller_data(mtd_to_nand(mtd));
-+
-+ mt7621_nfc_read_data(nfc, buf, len);
-+}
-+
-+static int mt7621_nfc_calc_ecc_strength(struct mt7621_nfc *nfc,
-+ u32 avail_ecc_bytes)
-+{
-+ struct nand_chip *nand = &nfc->nand;
-+ struct mtd_info *mtd = nand_to_mtd(nand);
-+ u32 strength;
-+ int i;
-+
-+ strength = avail_ecc_bytes * 8 / ECC_PARITY_BITS;
-+
-+ /* Find the closest supported ecc strength */
-+ for (i = ARRAY_SIZE(mt7621_ecc_strength) - 1; i >= 0; i--) {
-+ if (mt7621_ecc_strength[i] <= strength)
-+ break;
-+ }
-+
-+ if (unlikely(i < 0)) {
-+ pr_err("OOB size (%u) is not supported\n", mtd->oobsize);
-+ return -EINVAL;
-+ }
-+
-+ nand->ecc.strength = mt7621_ecc_strength[i];
-+ nand->ecc.bytes = DIV_ROUND_UP(nand->ecc.strength * ECC_PARITY_BITS, 8);
-+
-+ pr_debug("ECC strength adjusted to %u bits\n", nand->ecc.strength);
-+
-+ return i;
-+}
-+
-+static int mt7621_nfc_set_spare_per_sector(struct mt7621_nfc *nfc)
-+{
-+ struct nand_chip *nand = &nfc->nand;
-+ struct mtd_info *mtd = nand_to_mtd(nand);
-+ u32 size;
-+ int i;
-+
-+ size = nand->ecc.bytes + NFI_FDM_SIZE;
-+
-+ /* Find the closest supported spare size */
-+ for (i = 0; i < ARRAY_SIZE(mt7621_nfi_spare_size); i++) {
-+ if (mt7621_nfi_spare_size[i] >= size)
-+ break;
-+ }
-+
-+ if (unlikely(i >= ARRAY_SIZE(mt7621_nfi_spare_size))) {
-+ pr_err("OOB size (%u) is not supported\n", mtd->oobsize);
-+ return -EINVAL;
-+ }
-+
-+ nfc->spare_per_sector = mt7621_nfi_spare_size[i];
-+
-+ return i;
-+}
-+
-+static int mt7621_nfc_ecc_init(struct mt7621_nfc *nfc)
-+{
-+ struct nand_chip *nand = &nfc->nand;
-+ struct mtd_info *mtd = nand_to_mtd(nand);
-+ u32 avail_ecc_bytes, encode_block_size, decode_block_size;
-+ u32 ecc_enccfg, ecc_deccfg;
-+ int ecc_cap;
-+
-+ nand->ecc.options |= NAND_ECC_CUSTOM_PAGE_ACCESS;
-+
-+ nand->ecc.size = ECC_SECTOR_SIZE;
-+ nand->ecc.steps = mtd->writesize / nand->ecc.size;
-+
-+ avail_ecc_bytes = mtd->oobsize / nand->ecc.steps - NFI_FDM_SIZE;
-+
-+ ecc_cap = mt7621_nfc_calc_ecc_strength(nfc, avail_ecc_bytes);
-+ if (ecc_cap < 0)
-+ return ecc_cap;
-+
-+ /* Sector + FDM */
-+ encode_block_size = (nand->ecc.size + NFI_FDM_SIZE) * 8;
-+ ecc_enccfg = ecc_cap | FIELD_PREP(ENC_MODE, ENC_MODE_NFI) |
-+ FIELD_PREP(ENC_CNFG_MSG, encode_block_size);
-+
-+ /* Sector + FDM + ECC parity bits */
-+ decode_block_size = ((nand->ecc.size + NFI_FDM_SIZE) * 8) +
-+ nand->ecc.strength * ECC_PARITY_BITS;
-+ ecc_deccfg = ecc_cap | FIELD_PREP(DEC_MODE, DEC_MODE_NFI) |
-+ FIELD_PREP(DEC_CS, decode_block_size) |
-+ FIELD_PREP(DEC_CON, DEC_CON_EL) | DEC_EMPTY_EN;
-+
-+ mt7621_ecc_encoder_op(nfc, false);
-+ ecc_write32(nfc, ECC_ENCCNFG, ecc_enccfg);
-+
-+ mt7621_ecc_decoder_op(nfc, false);
-+ ecc_write32(nfc, ECC_DECCNFG, ecc_deccfg);
-+
-+ return 0;
-+}
-+
-+static int mt7621_nfc_set_page_format(struct mt7621_nfc *nfc)
-+{
-+ struct nand_chip *nand = &nfc->nand;
-+ struct mtd_info *mtd = nand_to_mtd(nand);
-+ int i, spare_size;
-+ u32 pagefmt;
-+
-+ spare_size = mt7621_nfc_set_spare_per_sector(nfc);
-+ if (spare_size < 0)
-+ return spare_size;
-+
-+ for (i = 0; i < ARRAY_SIZE(mt7621_nfi_page_size); i++) {
-+ if (mt7621_nfi_page_size[i] == mtd->writesize)
-+ break;
-+ }
-+
-+ if (unlikely(i >= ARRAY_SIZE(mt7621_nfi_page_size))) {
-+ pr_err("Page size (%u) is not supported\n", mtd->writesize);
-+ return -EINVAL;
-+ }
-+
-+ pagefmt = FIELD_PREP(PAGEFMT_PAGE, i) |
-+ FIELD_PREP(PAGEFMT_SPARE, spare_size) |
-+ FIELD_PREP(PAGEFMT_FDM, NFI_FDM_SIZE) |
-+ FIELD_PREP(PAGEFMT_FDM_ECC, NFI_FDM_SIZE);
-+
-+ nfi_write16(nfc, NFI_PAGEFMT, pagefmt);
-+
-+ return 0;
-+}
-+
-+static int mt7621_nfc_attach_chip(struct nand_chip *nand)
-+{
-+ struct mt7621_nfc *nfc = nand_get_controller_data(nand);
-+ int ret;
-+
-+ if (nand->options & NAND_BUSWIDTH_16) {
-+ pr_err("16-bit buswidth is not supported");
-+ return -EINVAL;
-+ }
-+
-+ ret = mt7621_nfc_ecc_init(nfc);
-+ if (ret)
-+ return ret;
-+
-+ return mt7621_nfc_set_page_format(nfc);
-+}
-+
-+static void mt7621_nfc_write_fdm(struct mt7621_nfc *nfc)
-+{
-+ struct nand_chip *nand = &nfc->nand;
-+ u32 vall, valm;
-+ u8 *oobptr;
-+ int i, j;
-+
-+ for (i = 0; i < nand->ecc.steps; i++) {
-+ vall = 0;
-+ valm = 0;
-+ oobptr = oob_fdm_ptr(nand, i);
-+
-+ for (j = 0; j < 4; j++)
-+ vall |= (u32)oobptr[j] << (j * 8);
-+
-+ for (j = 0; j < 4; j++)
-+ valm |= (u32)oobptr[j + 4] << (j * 8);
-+
-+ nfi_write32(nfc, NFI_FDML(i), vall);
-+ nfi_write32(nfc, NFI_FDMM(i), valm);
-+ }
-+}
-+
-+static void mt7621_nfc_read_sector_fdm(struct mt7621_nfc *nfc, u32 sect)
-+{
-+ struct nand_chip *nand = &nfc->nand;
-+ u32 vall, valm;
-+ u8 *oobptr;
-+ int i;
-+
-+ vall = nfi_read32(nfc, NFI_FDML(sect));
-+ valm = nfi_read32(nfc, NFI_FDMM(sect));
-+ oobptr = oob_fdm_ptr(nand, sect);
-+
-+ for (i = 0; i < 4; i++)
-+ oobptr[i] = (vall >> (i * 8)) & 0xff;
-+
-+ for (i = 0; i < 4; i++)
-+ oobptr[i + 4] = (valm >> (i * 8)) & 0xff;
-+}
-+
-+static int mt7621_nfc_read_page_hwecc(struct mtd_info *mtd,
-+ struct nand_chip *nand, uint8_t *buf,
-+ int oob_required, int page)
-+{
-+ struct mt7621_nfc *nfc = nand_get_controller_data(nand);
-+ int bitflips = 0, ret = 0;
-+ int rc, i;
-+
-+ nand_read_page_op(nand, page, 0, NULL, 0);
-+
-+ nfi_write16(nfc, NFI_CNFG, FIELD_PREP(CNFG_OP_MODE, CNFG_OP_CUSTOM) |
-+ CNFG_READ_MODE | CNFG_AUTO_FMT_EN | CNFG_HW_ECC_EN);
-+
-+ mt7621_ecc_decoder_op(nfc, true);
-+
-+ nfi_write16(nfc, NFI_CON, FIELD_PREP(CON_NFI_SEC, nand->ecc.steps) |
-+ CON_NFI_BRD);
-+
-+ for (i = 0; i < nand->ecc.steps; i++) {
-+ if (buf)
-+ mt7621_nfc_read_data(nfc, page_data_ptr(nand, buf, i),
-+ nand->ecc.size);
-+ else
-+ mt7621_nfc_read_data_discard(nfc, nand->ecc.size);
-+
-+ rc = mt7621_ecc_decoder_wait_done(nfc, i);
-+
-+ mt7621_nfc_read_sector_fdm(nfc, i);
-+
-+ if (rc < 0) {
-+ ret = -EIO;
-+ continue;
-+ }
-+
-+ rc = mt7621_ecc_correct_check(nfc,
-+ buf ? page_data_ptr(nand, buf, i) : NULL,
-+ oob_fdm_ptr(nand, i), i);
-+
-+ if (rc < 0) {
-+ pr_warn("Uncorrectable ECC error at page %d step %d\n",
-+ page, i);
-+ bitflips = nand->ecc.strength + 1;
-+ mtd->ecc_stats.failed++;
-+ } else {
-+ if (rc > bitflips)
-+ bitflips = rc;
-+ mtd->ecc_stats.corrected += rc;
-+ }
-+ }
-+
-+ mt7621_ecc_decoder_op(nfc, false);
-+
-+ nfi_write16(nfc, NFI_CON, 0);
-+
-+ if (ret < 0)
-+ return ret;
-+
-+ return bitflips;
-+}
-+
-+static int mt7621_nfc_read_page_raw(struct mtd_info *mtd,
-+ struct nand_chip *nand, uint8_t *buf,
-+ int oob_required, int page)
-+{
-+ struct mt7621_nfc *nfc = nand_get_controller_data(nand);
-+ int i;
-+
-+ nand_read_page_op(nand, page, 0, NULL, 0);
-+
-+ nfi_write16(nfc, NFI_CNFG, FIELD_PREP(CNFG_OP_MODE, CNFG_OP_CUSTOM) |
-+ CNFG_READ_MODE);
-+
-+ nfi_write16(nfc, NFI_CON, FIELD_PREP(CON_NFI_SEC, nand->ecc.steps) |
-+ CON_NFI_BRD);
-+
-+ for (i = 0; i < nand->ecc.steps; i++) {
-+ /* Read data */
-+ if (buf)
-+ mt7621_nfc_read_data(nfc, page_data_ptr(nand, buf, i),
-+ nand->ecc.size);
-+ else
-+ mt7621_nfc_read_data_discard(nfc, nand->ecc.size);
-+
-+ /* Read FDM */
-+ mt7621_nfc_read_data(nfc, oob_fdm_ptr(nand, i), NFI_FDM_SIZE);
-+
-+ /* Read ECC parity data */
-+ mt7621_nfc_read_data(nfc, oob_ecc_ptr(nfc, i),
-+ nfc->spare_per_sector - NFI_FDM_SIZE);
-+ }
-+
-+ nfi_write16(nfc, NFI_CON, 0);
-+
-+ return 0;
-+}
-+
-+static int mt7621_nfc_read_oob_hwecc(struct mtd_info *mtd,
-+ struct nand_chip *nand, int page)
-+{
-+ return mt7621_nfc_read_page_hwecc(mtd, nand, NULL, 1, page);
-+}
-+
-+static int mt7621_nfc_read_oob_raw(struct mtd_info *mtd,
-+ struct nand_chip *nand, int page)
-+{
-+ return mt7621_nfc_read_page_raw(mtd, nand, NULL, 1, page);
-+}
-+
-+static int mt7621_nfc_check_empty_page(struct nand_chip *nand, const u8 *buf)
-+{
-+ struct mtd_info *mtd = nand_to_mtd(nand);
-+ u8 *oobptr;
-+ u32 i, j;
-+
-+ if (buf) {
-+ for (i = 0; i < mtd->writesize; i++)
-+ if (buf[i] != 0xff)
-+ return 0;
-+ }
-+
-+ for (i = 0; i < nand->ecc.steps; i++) {
-+ oobptr = oob_fdm_ptr(nand, i);
-+ for (j = 0; j < NFI_FDM_SIZE; j++)
-+ if (oobptr[j] != 0xff)
-+ return 0;
-+ }
-+
-+ return 1;
-+}
-+
-+static int mt7621_nfc_write_page_hwecc(struct mtd_info *mtd,
-+ struct nand_chip *nand,
-+ const u8 *buf, int oob_required,
-+ int page)
-+{
-+ struct mt7621_nfc *nfc = nand_get_controller_data(nand);
-+
-+ if (mt7621_nfc_check_empty_page(nand, buf)) {
-+ /*
-+ * MT7621 ECC engine always generates parity code for input
-+ * pages, even for empty pages. Doing so will write back ECC
-+ * parity code to the oob region, which means such pages will
-+ * no longer be empty pages.
-+ *
-+ * To avoid this, stop write operation if current page is an
-+ * empty page.
-+ */
-+ return 0;
-+ }
-+
-+ nand_prog_page_begin_op(nand, page, 0, NULL, 0);
-+
-+ nfi_write16(nfc, NFI_CNFG, FIELD_PREP(CNFG_OP_MODE, CNFG_OP_CUSTOM) |
-+ CNFG_AUTO_FMT_EN | CNFG_HW_ECC_EN);
-+
-+ mt7621_ecc_encoder_op(nfc, true);
-+
-+ mt7621_nfc_write_fdm(nfc);
-+
-+ nfi_write16(nfc, NFI_CON, FIELD_PREP(CON_NFI_SEC, nand->ecc.steps) |
-+ CON_NFI_BWR);
-+
-+ if (buf)
-+ mt7621_nfc_write_data(nfc, buf, mtd->writesize);
-+ else
-+ mt7621_nfc_write_data_empty(nfc, mtd->writesize);
-+
-+ mt7621_nfc_wait_write_completion(nfc, nand);
-+
-+ mt7621_ecc_encoder_op(nfc, false);
-+
-+ nfi_write16(nfc, NFI_CON, 0);
-+
-+ return nand_prog_page_end_op(nand);
-+}
-+
-+static int mt7621_nfc_write_page_raw(struct mtd_info *mtd,
-+ struct nand_chip *nand,
-+ const u8 *buf, int oob_required,
-+ int page)
-+{
-+ struct mt7621_nfc *nfc = nand_get_controller_data(nand);
-+ int i;
-+
-+ nand_prog_page_begin_op(nand, page, 0, NULL, 0);
-+
-+ nfi_write16(nfc, NFI_CNFG, FIELD_PREP(CNFG_OP_MODE, CNFG_OP_CUSTOM));
-+
-+ nfi_write16(nfc, NFI_CON, FIELD_PREP(CON_NFI_SEC, nand->ecc.steps) |
-+ CON_NFI_BWR);
-+
-+ for (i = 0; i < nand->ecc.steps; i++) {
-+ /* Write data */
-+ if (buf)
-+ mt7621_nfc_write_data(nfc, page_data_ptr(nand, buf, i),
-+ nand->ecc.size);
-+ else
-+ mt7621_nfc_write_data_empty(nfc, nand->ecc.size);
-+
-+ /* Write FDM */
-+ mt7621_nfc_write_data(nfc, oob_fdm_ptr(nand, i),
-+ NFI_FDM_SIZE);
-+
-+ /* Write dummy ECC parity data */
-+ mt7621_nfc_write_data_empty(nfc, nfc->spare_per_sector -
-+ NFI_FDM_SIZE);
-+ }
-+
-+ mt7621_nfc_wait_write_completion(nfc, nand);
-+
-+ nfi_write16(nfc, NFI_CON, 0);
-+
-+ return nand_prog_page_end_op(nand);
-+}
-+
-+static int mt7621_nfc_write_oob_hwecc(struct mtd_info *mtd,
-+ struct nand_chip *nand, int page)
-+{
-+ return mt7621_nfc_write_page_hwecc(mtd, nand, NULL, 1, page);
-+}
-+
-+static int mt7621_nfc_write_oob_raw(struct mtd_info *mtd,
-+ struct nand_chip *nand, int page)
-+{
-+ return mt7621_nfc_write_page_raw(mtd, nand, NULL, 1, page);
-+}
-+
-+static int mt7621_nfc_ooblayout_free(struct mtd_info *mtd, int section,
-+ struct mtd_oob_region *oob_region)
-+{
-+ struct nand_chip *nand = mtd_to_nand(mtd);
-+
-+ if (section >= nand->ecc.steps)
-+ return -ERANGE;
-+
-+ oob_region->length = NFI_FDM_SIZE - 1;
-+ oob_region->offset = section * NFI_FDM_SIZE + 1;
-+
-+ return 0;
-+}
-+
-+static int mt7621_nfc_ooblayout_ecc(struct mtd_info *mtd, int section,
-+ struct mtd_oob_region *oob_region)
-+{
-+ struct nand_chip *nand = mtd_to_nand(mtd);
-+
-+ if (section)
-+ return -ERANGE;
-+
-+ oob_region->offset = NFI_FDM_SIZE * nand->ecc.steps;
-+ oob_region->length = mtd->oobsize - oob_region->offset;
-+
-+ return 0;
-+}
-+
-+static const struct mtd_ooblayout_ops mt7621_nfc_ooblayout_ops = {
-+ .rfree = mt7621_nfc_ooblayout_free,
-+ .ecc = mt7621_nfc_ooblayout_ecc,
-+};
-+
-+/*
-+ * This function will override the default one which is not supposed to be
-+ * used for ECC syndrome based pages.
-+ */
-+static int mt7621_nfc_block_bad(struct mtd_info *mtd, loff_t ofs)
-+{
-+ struct nand_chip *nand = mtd_to_nand(mtd);
-+ struct mtd_oob_ops ops;
-+ int ret, i = 0;
-+ u16 bad;
-+
-+ memset(&ops, 0, sizeof(ops));
-+ ops.oobbuf = (uint8_t *)&bad;
-+ ops.ooboffs = nand->badblockpos;
-+ if (nand->options & NAND_BUSWIDTH_16) {
-+ ops.ooboffs &= ~0x01;
-+ ops.ooblen = 2;
-+ } else {
-+ ops.ooblen = 1;
-+ }
-+ ops.mode = MTD_OPS_RAW;
-+
-+ /* Read from first/last page(s) if necessary */
-+ if (nand->bbt_options & NAND_BBT_SCANLASTPAGE)
-+ ofs += mtd->erasesize - mtd->writesize;
-+
-+ do {
-+ ret = mtd_read_oob(mtd, ofs, &ops);
-+ if (ret)
-+ return ret;
-+
-+ if (likely(nand->badblockbits == 8))
-+ ret = bad != 0xFF;
-+ else
-+ ret = hweight8(bad) < nand->badblockbits;
-+
-+ i++;
-+ ofs += mtd->writesize;
-+ } while (!ret && (nand->bbt_options & NAND_BBT_SCAN2NDPAGE) && i < 2);
-+
-+ return ret;
-+}
-+
-+static void mt7621_nfc_init_chip(struct mt7621_nfc *nfc)
-+{
-+ struct nand_chip *nand = &nfc->nand;
-+ struct mtd_info *mtd;
-+ int ret;
-+
-+ nand_set_controller_data(nand, nfc);
-+
-+ nand->options |= NAND_NO_SUBPAGE_WRITE;
-+
-+ nand->ecc.mode = NAND_ECC_HW_SYNDROME;
-+ nand->ecc.read_page = mt7621_nfc_read_page_hwecc;
-+ nand->ecc.read_page_raw = mt7621_nfc_read_page_raw;
-+ nand->ecc.write_page = mt7621_nfc_write_page_hwecc;
-+ nand->ecc.write_page_raw = mt7621_nfc_write_page_raw;
-+ nand->ecc.read_oob = mt7621_nfc_read_oob_hwecc;
-+ nand->ecc.read_oob_raw = mt7621_nfc_read_oob_raw;
-+ nand->ecc.write_oob = mt7621_nfc_write_oob_hwecc;
-+ nand->ecc.write_oob_raw = mt7621_nfc_write_oob_raw;
-+
-+ nand->dev_ready = mt7621_nfc_dev_ready;
-+ nand->select_chip = mt7621_nfc_select_chip;
-+ nand->write_byte = mt7621_nfc_write_byte;
-+ nand->write_buf = mt7621_nfc_write_buf;
-+ nand->read_byte = mt7621_nfc_read_byte;
-+ nand->read_buf = mt7621_nfc_read_buf;
-+ nand->cmd_ctrl = mt7621_nfc_cmd_ctrl;
-+ nand->block_bad = mt7621_nfc_block_bad;
-+
-+ mtd = nand_to_mtd(nand);
-+ mtd_set_ooblayout(mtd, &mt7621_nfc_ooblayout_ops);
-+
-+ /* Reset NFI master */
-+ mt7621_nfc_hw_init(nfc);
-+
-+ ret = nand_scan_ident(mtd, 1, NULL);
-+ if (ret)
-+ return;
-+
-+ mt7621_nfc_attach_chip(nand);
-+
-+ ret = nand_scan_tail(mtd);
-+ if (ret)
-+ return;
-+
-+ nand_register(0, mtd);
-+}
-+
-+static void mt7621_nfc_set_regs(struct mt7621_nfc *nfc)
-+{
-+ nfc->nfi_regs = (void __iomem *)CKSEG1ADDR(NFI_BASE);
-+ nfc->ecc_regs = (void __iomem *)CKSEG1ADDR(NFI_ECC_BASE);
-+}
-+
-+void mt7621_nfc_spl_init(struct mt7621_nfc *nfc)
-+{
-+ struct nand_chip *nand = &nfc->nand;
-+
-+ mt7621_nfc_set_regs(nfc);
-+
-+ nand_set_controller_data(nand, nfc);
-+
-+ nand->options |= NAND_NO_SUBPAGE_WRITE;
-+
-+ nand->ecc.mode = NAND_ECC_HW_SYNDROME;
-+ nand->ecc.read_page = mt7621_nfc_read_page_hwecc;
-+
-+ nand->dev_ready = mt7621_nfc_dev_ready;
-+ nand->select_chip = mt7621_nfc_select_chip;
-+ nand->read_byte = mt7621_nfc_read_byte;
-+ nand->read_buf = mt7621_nfc_read_buf;
-+ nand->cmd_ctrl = mt7621_nfc_cmd_ctrl;
-+
-+ /* Reset NFI master */
-+ mt7621_nfc_hw_init(nfc);
-+}
-+
-+int mt7621_nfc_spl_post_init(struct mt7621_nfc *nfc)
-+{
-+ struct nand_chip *nand = &nfc->nand;
-+ int nand_maf_id, nand_dev_id;
-+ struct nand_flash_dev *type;
-+
-+ type = nand_get_flash_type(&nand->mtd, nand, &nand_maf_id,
-+ &nand_dev_id, NULL);
-+
-+ if (IS_ERR(type))
-+ return PTR_ERR(type);
-+
-+ nand->numchips = 1;
-+ nand->mtd.size = nand->chipsize;
-+
-+ return mt7621_nfc_attach_chip(nand);
-+}
-+
-+void board_nand_init(void)
-+{
-+ mt7621_nfc_set_regs(&nfc_dev);
-+ mt7621_nfc_init_chip(&nfc_dev);
-+}
---- /dev/null
-+++ b/drivers/mtd/nand/raw/mt7621_nand.h
-@@ -0,0 +1,29 @@
-+/* SPDX-License-Identifier: GPL-2.0 */
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#ifndef _MT7621_NAND_H_
-+#define _MT7621_NAND_H_
-+
-+#include <linux/types.h>
-+#include <linux/mtd/mtd.h>
-+#include <linux/compiler.h>
-+#include <linux/mtd/rawnand.h>
-+
-+struct mt7621_nfc {
-+ struct nand_chip nand;
-+
-+ void __iomem *nfi_regs;
-+ void __iomem *ecc_regs;
-+
-+ u32 spare_per_sector;
-+};
-+
-+/* for SPL */
-+void mt7621_nfc_spl_init(struct mt7621_nfc *nfc);
-+int mt7621_nfc_spl_post_init(struct mt7621_nfc *nfc);
-+
-+#endif /* _MT7621_NAND_H_ */
---- /dev/null
-+++ b/drivers/mtd/nand/raw/mt7621_nand_spl.c
-@@ -0,0 +1,237 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * Copyright (C) 2022 MediaTek Inc. All rights reserved.
-+ *
-+ * Author: Weijie Gao <weijie.gao@mediatek.com>
-+ */
-+
-+#include <image.h>
-+#include <malloc.h>
-+#include <linux/sizes.h>
-+#include <linux/delay.h>
-+#include <linux/mtd/rawnand.h>
-+#include "mt7621_nand.h"
-+
-+static struct mt7621_nfc nfc_dev;
-+static u8 *buffer;
-+static int nand_valid;
-+
-+static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
-+ int column, int page_addr)
-+{
-+ register struct nand_chip *chip = mtd_to_nand(mtd);
-+
-+ /* Command latch cycle */
-+ chip->cmd_ctrl(mtd, command, NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE);
-+
-+ if (column != -1 || page_addr != -1) {
-+ int ctrl = NAND_CTRL_CHANGE | NAND_NCE | NAND_ALE;
-+
-+ /* Serially input address */
-+ if (column != -1) {
-+ chip->cmd_ctrl(mtd, column, ctrl);
-+ ctrl &= ~NAND_CTRL_CHANGE;
-+ if (command != NAND_CMD_READID)
-+ chip->cmd_ctrl(mtd, column >> 8, ctrl);
-+ }
-+ if (page_addr != -1) {
-+ chip->cmd_ctrl(mtd, page_addr, ctrl);
-+ chip->cmd_ctrl(mtd, page_addr >> 8,
-+ NAND_NCE | NAND_ALE);
-+ if (chip->options & NAND_ROW_ADDR_3)
-+ chip->cmd_ctrl(mtd, page_addr >> 16,
-+ NAND_NCE | NAND_ALE);
-+ }
-+ }
-+ chip->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
-+
-+ /*
-+ * Program and erase have their own busy handlers status, sequential
-+ * in and status need no delay.
-+ */
-+ switch (command) {
-+ case NAND_CMD_STATUS:
-+ case NAND_CMD_READID:
-+ case NAND_CMD_SET_FEATURES:
-+ return;
-+
-+ case NAND_CMD_READ0:
-+ chip->cmd_ctrl(mtd, NAND_CMD_READSTART,
-+ NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE);
-+ chip->cmd_ctrl(mtd, NAND_CMD_NONE,
-+ NAND_NCE | NAND_CTRL_CHANGE);
-+ }
-+
-+ /*
-+ * Apply this short delay always to ensure that we do wait tWB in
-+ * any case on any machine.
-+ */
-+ ndelay(100);
-+
-+ nand_wait_ready(mtd);
-+}
-+
-+static int nfc_read_page_hwecc(struct mtd_info *mtd, void *buf,
-+ unsigned int page)
-+{
-+ struct nand_chip *chip = mtd_to_nand(mtd);
-+ int ret;
-+
-+ chip->cmdfunc(mtd, NAND_CMD_READ0, 0x0, page);
-+
-+ ret = chip->ecc.read_page(mtd, chip, buf, 1, page);
-+ if (ret < 0 || ret > chip->ecc.strength)
-+ return -1;
-+
-+ return 0;
-+}
-+
-+static int nfc_read_oob_hwecc(struct mtd_info *mtd, void *buf, u32 len,
-+ unsigned int page)
-+{
-+ struct nand_chip *chip = mtd_to_nand(mtd);
-+ int ret;
-+
-+ chip->cmdfunc(mtd, NAND_CMD_READ0, 0x0, page);
-+
-+ ret = chip->ecc.read_page(mtd, chip, NULL, 1, page);
-+ if (ret < 0)
-+ return -1;
-+
-+ if (len > mtd->oobsize)
-+ len = mtd->oobsize;
-+
-+ memcpy(buf, chip->oob_poi, len);
-+
-+ return 0;
-+}
-+
-+static int nfc_check_bad_block(struct mtd_info *mtd, unsigned int page)
-+{
-+ struct nand_chip *chip = mtd_to_nand(mtd);
-+ u32 pages_per_block, i = 0;
-+ int ret;
-+ u8 bad;
-+
-+ pages_per_block = 1 << (mtd->erasesize_shift - mtd->writesize_shift);
-+
-+ /* Read from first/last page(s) if necessary */
-+ if (chip->bbt_options & NAND_BBT_SCANLASTPAGE) {
-+ page += pages_per_block - 1;
-+ if (chip->bbt_options & NAND_BBT_SCAN2NDPAGE)
-+ page--;
-+ }
-+
-+ do {
-+ ret = nfc_read_oob_hwecc(mtd, &bad, 1, page);
-+ if (ret)
-+ return ret;
-+
-+ ret = bad != 0xFF;
-+
-+ i++;
-+ page++;
-+ } while (!ret && (chip->bbt_options & NAND_BBT_SCAN2NDPAGE) && i < 2);
-+
-+ return ret;
-+}
-+
-+int nand_spl_load_image(uint32_t offs, unsigned int size, void *dest)
-+{
-+ struct mt7621_nfc *nfc = &nfc_dev;
-+ struct nand_chip *chip = &nfc->nand;
-+ struct mtd_info *mtd = &chip->mtd;
-+ u32 addr, col, page, chksz;
-+ bool check_bad = true;
-+
-+ if (!nand_valid)
-+ return -ENODEV;
-+
-+ while (size) {
-+ if (check_bad || !(offs & mtd->erasesize_mask)) {
-+ addr = offs & (~mtd->erasesize_mask);
-+ page = addr >> mtd->writesize_shift;
-+ if (nfc_check_bad_block(mtd, page)) {
-+ /* Skip bad block */
-+ if (addr >= mtd->size - mtd->erasesize)
-+ return -1;
-+
-+ offs += mtd->erasesize;
-+ continue;
-+ }
-+
-+ check_bad = false;
-+ }
-+
-+ col = offs & mtd->writesize_mask;
-+ page = offs >> mtd->writesize_shift;
-+ chksz = min(mtd->writesize - col, (uint32_t)size);
-+
-+ if (unlikely(chksz < mtd->writesize)) {
-+ /* Not reading a full page */
-+ if (nfc_read_page_hwecc(mtd, buffer, page))
-+ return -1;
-+
-+ memcpy(dest, buffer + col, chksz);
-+ } else {
-+ if (nfc_read_page_hwecc(mtd, dest, page))
-+ return -1;
-+ }
-+
-+ dest += chksz;
-+ offs += chksz;
-+ size -= chksz;
-+ }
-+
-+ return 0;
-+}
-+
-+int nand_default_bbt(struct mtd_info *mtd)
-+{
-+ return 0;
-+}
-+
-+unsigned long nand_size(void)
-+{
-+ if (!nand_valid)
-+ return 0;
-+
-+ /* Unlikely that NAND size > 2GBytes */
-+ if (nfc_dev.nand.chipsize <= SZ_2G)
-+ return nfc_dev.nand.chipsize;
-+
-+ return SZ_2G;
-+}
-+
-+void nand_deselect(void)
-+{
-+}
-+
-+void nand_init(void)
-+{
-+ struct mtd_info *mtd;
-+ struct nand_chip *chip;
-+
-+ if (nand_valid)
-+ return;
-+
-+ mt7621_nfc_spl_init(&nfc_dev);
-+
-+ chip = &nfc_dev.nand;
-+ mtd = &chip->mtd;
-+ chip->cmdfunc = nand_command_lp;
-+
-+ if (mt7621_nfc_spl_post_init(&nfc_dev))
-+ return;
-+
-+ mtd->erasesize_shift = ffs(mtd->erasesize) - 1;
-+ mtd->writesize_shift = ffs(mtd->writesize) - 1;
-+ mtd->erasesize_mask = (1 << mtd->erasesize_shift) - 1;
-+ mtd->writesize_mask = (1 << mtd->writesize_shift) - 1;
-+
-+ buffer = malloc(mtd->writesize);
-+ if (!buffer)
-+ return;
-+
-+ nand_valid = 1;
-+}
+++ /dev/null
-From 474082b03ae2b569f9daf43f78b91b57f7a1ae50 Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:23:53 +0800
-Subject: [PATCH 21/25] spl: allow using nand base without standard nand driver
-
-This patch removes the dependency to SPL_NAND_DRIVERS for SPL_NAND_BASE to
-allow minimal spl nand driver to use nand base for probing NAND chips.
-
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- common/spl/Kconfig | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/common/spl/Kconfig
-+++ b/common/spl/Kconfig
-@@ -764,7 +764,7 @@ config SPL_NAND_SIMPLE
- expose the cmd_ctrl() interface.
-
- config SPL_NAND_BASE
-- depends on SPL_NAND_DRIVERS
-+ depends on SPL_NAND_SUPPORT
- bool "Use Base NAND Driver"
- help
- Include nand_base.c in the SPL.
+++ /dev/null
-From ba9c81e720f39b5dbc14592252bfc9402afee79d Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:23:58 +0800
-Subject: [PATCH 22/25] spl: spl_legacy: fix the use of SPL_COPY_PAYLOAD_ONLY
-
-If the payload is compressed, SPL_COPY_PAYLOAD_ONLY should always be set
-since the payload will not be directly read to its load address. The
-payload will first be read to a temporary buffer, and then be decompressed
-to its load address, without image header.
-
-If the payload is not compressed, and SPL_COPY_PAYLOAD_ONLY is set, image
-header should be skipped on loading. Otherwise image header should also be
-read to its load address.
-
-Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- common/spl/spl_legacy.c | 21 +++++++++++++++++++--
- 1 file changed, 19 insertions(+), 2 deletions(-)
-
---- a/common/spl/spl_legacy.c
-+++ b/common/spl/spl_legacy.c
-@@ -88,15 +88,29 @@ int spl_load_legacy_img(struct spl_image
- /* Read header into local struct */
- load->read(load, header, sizeof(hdr), &hdr);
-
-+ /*
-+ * If the payload is compressed, the decompressed data should be
-+ * directly write to its load address.
-+ */
-+ if (spl_image_get_comp(&hdr) != IH_COMP_NONE)
-+ spl_image->flags |= SPL_COPY_PAYLOAD_ONLY;
-+
- ret = spl_parse_image_header(spl_image, bootdev, &hdr);
- if (ret)
- return ret;
-
-- dataptr = header + sizeof(hdr);
--
- /* Read image */
- switch (spl_image_get_comp(&hdr)) {
- case IH_COMP_NONE:
-+ dataptr = header;
-+
-+ /*
-+ * Image header will be skipped only if SPL_COPY_PAYLOAD_ONLY
-+ * is set
-+ */
-+ if (spl_image->flags & SPL_COPY_PAYLOAD_ONLY)
-+ dataptr += sizeof(hdr);
-+
- load->read(load, dataptr, spl_image->size,
- (void *)(unsigned long)spl_image->load_addr);
- break;
-@@ -104,6 +118,9 @@ int spl_load_legacy_img(struct spl_image
- case IH_COMP_LZMA:
- lzma_len = LZMA_LEN;
-
-+ /* dataptr points to compressed payload */
-+ dataptr = header + sizeof(hdr);
-+
- debug("LZMA: Decompressing %08lx to %08lx\n",
- dataptr, spl_image->load_addr);
- src = malloc(spl_image->size);
+++ /dev/null
-From b4e5137067d34a099efd921532ece177560789ca Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:24:04 +0800
-Subject: [PATCH 23/25] spl: nand: support loading legacy image with payload
- compressed
-
-Add support to load legacy image with payload compressed. This redirects
-the boot flow for all legacy images. If the payload is not compressed, the
-actual behavior will remain unchanged.
-
-Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- common/spl/spl_nand.c | 27 +++++++++++++++++++++++++++
- 1 file changed, 27 insertions(+)
-
---- a/common/spl/spl_nand.c
-+++ b/common/spl/spl_nand.c
-@@ -56,6 +56,21 @@ static ulong spl_nand_fit_read(struct sp
- return size / load->bl_len;
- }
-
-+static ulong spl_nand_legacy_read(struct spl_load_info *load, ulong offs,
-+ ulong size, void *dst)
-+{
-+ int err;
-+
-+ debug("%s: offs %lx, size %lx, dst %p\n",
-+ __func__, offs, size, dst);
-+
-+ err = nand_spl_load_image(offs, size, dst);
-+ if (err)
-+ return 0;
-+
-+ return size;
-+}
-+
- struct mtd_info * __weak nand_get_mtd(void)
- {
- return NULL;
-@@ -93,6 +108,18 @@ static int spl_nand_load_element(struct
- load.bl_len = bl_len;
- load.read = spl_nand_fit_read;
- return spl_load_imx_container(spl_image, &load, offset / bl_len);
-+ } else if (IS_ENABLED(CONFIG_SPL_LEGACY_IMAGE_FORMAT) &&
-+ image_get_magic(header) == IH_MAGIC) {
-+ struct spl_load_info load;
-+
-+ debug("Found legacy image\n");
-+ load.dev = NULL;
-+ load.priv = NULL;
-+ load.filename = NULL;
-+ load.bl_len = 1;
-+ load.read = spl_nand_legacy_read;
-+
-+ return spl_load_legacy_img(spl_image, bootdev, &load, offset);
- } else {
- err = spl_parse_image_header(spl_image, bootdev, header);
- if (err)
+++ /dev/null
-From 18dd1ef9417d0880f2f492b55bd4d9ede499f137 Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:24:10 +0800
-Subject: [PATCH 24/25] tools: mtk_image: add support for MT7621 NAND images
-
-The BootROM of MT7621 requires a image header for SPL to record its size
-and load address when booting from NAND.
-
-To create such an image, one can use the following command line:
-mkimage -T mtk_image -a 0x80200000 -e 0x80200000 -n "mt7621=1"
--d u-boot-spl-ddr.bin u-boot-spl-ddr.img
-
-Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- tools/mtk_image.c | 182 ++++++++++++++++++++++++++++++++++++++++++++++
- tools/mtk_image.h | 24 ++++++
- 2 files changed, 206 insertions(+)
-
---- a/tools/mtk_image.c
-+++ b/tools/mtk_image.c
-@@ -6,7 +6,9 @@
- * Author: Weijie Gao <weijie.gao@mediatek.com>
- */
-
-+#include <time.h>
- #include <image.h>
-+#include <u-boot/crc.h>
- #include <u-boot/sha256.h>
- #include "imagetool.h"
- #include "mtk_image.h"
-@@ -251,17 +253,45 @@ static uint32_t img_size;
- static enum brlyt_img_type hdr_media;
- static uint32_t hdr_offset;
- static int use_lk_hdr;
-+static int use_mt7621_hdr;
- static bool is_arm64_image;
-
- /* LK image name */
- static char lk_name[32] = "U-Boot";
-
-+/* CRC32 normal table required by MT7621 image */
-+static uint32_t crc32tbl[256];
-+
- /* NAND header selected by user */
- static const union nand_boot_header *hdr_nand;
-
- /* GFH header + 2 * 4KB pages of NAND */
- static char hdr_tmp[sizeof(struct gfh_header) + 0x2000];
-
-+static uint32_t crc32_normal_cal(uint32_t crc, const void *data, size_t length,
-+ const uint32_t *crc32c_table)
-+{
-+ const uint8_t *p = data;
-+
-+ while (length--)
-+ crc = crc32c_table[(uint8_t)((crc >> 24) ^ *p++)] ^ (crc << 8);
-+
-+ return crc;
-+}
-+
-+static void crc32_normal_init(uint32_t *crc32c_table, uint32_t poly)
-+{
-+ uint32_t v, i, j;
-+
-+ for (i = 0; i < 256; i++) {
-+ v = i << 24;
-+ for (j = 0; j < 8; j++)
-+ v = (v << 1) ^ ((v & (1 << 31)) ? poly : 0);
-+
-+ crc32c_table[i] = v;
-+ }
-+}
-+
- static int mtk_image_check_image_types(uint8_t type)
- {
- if (type == IH_TYPE_MTKIMAGE)
-@@ -283,6 +313,7 @@ static int mtk_brom_parse_imagename(cons
- static const char *hdr_offs = "";
- static const char *nandinfo = "";
- static const char *lk = "";
-+ static const char *mt7621 = "";
- static const char *arm64_param = "";
-
- key = buf;
-@@ -332,6 +363,9 @@ static int mtk_brom_parse_imagename(cons
- if (!strcmp(key, "lk"))
- lk = val;
-
-+ if (!strcmp(key, "mt7621"))
-+ mt7621 = val;
-+
- if (!strcmp(key, "lkname"))
- snprintf(lk_name, sizeof(lk_name), "%s", val);
-
-@@ -352,6 +386,13 @@ static int mtk_brom_parse_imagename(cons
- return 0;
- }
-
-+ /* if user specified MT7621 image header, skip following checks */
-+ if (mt7621 && mt7621[0] == '1') {
-+ use_mt7621_hdr = 1;
-+ free(buf);
-+ return 0;
-+ }
-+
- /* parse media type */
- for (i = 0; i < ARRAY_SIZE(brom_images); i++) {
- if (!strcmp(brom_images[i].name, media)) {
-@@ -419,6 +460,13 @@ static int mtk_image_vrec_header(struct
- return 0;
- }
-
-+ if (use_mt7621_hdr) {
-+ tparams->header_size = image_get_header_size();
-+ tparams->hdr = &hdr_tmp;
-+ memset(&hdr_tmp, 0, tparams->header_size);
-+ return 0;
-+ }
-+
- if (hdr_media == BRLYT_TYPE_NAND || hdr_media == BRLYT_TYPE_SNAND)
- tparams->header_size = 2 * le16_to_cpu(hdr_nand->pagesize);
- else
-@@ -579,9 +627,90 @@ static int mtk_image_verify_nand_header(
- return 0;
- }
-
-+static uint32_t crc32be_cal(const void *data, size_t length)
-+{
-+ uint32_t crc = 0;
-+ uint8_t c;
-+
-+ if (crc32tbl[1] != MT7621_IH_CRC_POLYNOMIAL)
-+ crc32_normal_init(crc32tbl, MT7621_IH_CRC_POLYNOMIAL);
-+
-+ crc = crc32_normal_cal(crc, data, length, crc32tbl);
-+
-+ for (; length; length >>= 8) {
-+ c = length & 0xff;
-+ crc = crc32_normal_cal(crc, &c, 1, crc32tbl);
-+ }
-+
-+ return ~crc;
-+}
-+
-+static int mtk_image_verify_mt7621_header(const uint8_t *ptr, int print)
-+{
-+ const image_header_t *hdr = (const image_header_t *)ptr;
-+ struct mt7621_nand_header *nhdr;
-+ uint32_t spl_size, crcval;
-+ image_header_t header;
-+ int ret;
-+
-+ spl_size = image_get_size(hdr);
-+
-+ if (spl_size > img_size) {
-+ if (print)
-+ printf("Incomplete SPL image\n");
-+ return -1;
-+ }
-+
-+ ret = image_check_hcrc(hdr);
-+ if (!ret) {
-+ if (print)
-+ printf("Bad header CRC\n");
-+ return -1;
-+ }
-+
-+ ret = image_check_dcrc(hdr);
-+ if (!ret) {
-+ if (print)
-+ printf("Bad data CRC\n");
-+ return -1;
-+ }
-+
-+ /* Copy header so we can blank CRC field for re-calculation */
-+ memmove(&header, hdr, image_get_header_size());
-+ image_set_hcrc(&header, 0);
-+
-+ nhdr = (struct mt7621_nand_header *)header.ih_name;
-+ crcval = be32_to_cpu(nhdr->crc);
-+ nhdr->crc = 0;
-+
-+ if (crcval != crc32be_cal(&header, image_get_header_size())) {
-+ if (print)
-+ printf("Bad NAND header CRC\n");
-+ return -1;
-+ }
-+
-+ if (print) {
-+ printf("Load Address: %08x\n", image_get_load(hdr));
-+
-+ printf("Image Name: %.*s\n", MT7621_IH_NMLEN,
-+ image_get_name(hdr));
-+
-+ if (IMAGE_ENABLE_TIMESTAMP) {
-+ printf("Created: ");
-+ genimg_print_time((time_t)image_get_time(hdr));
-+ }
-+
-+ printf("Data Size: ");
-+ genimg_print_size(image_get_data_size(hdr));
-+ }
-+
-+ return 0;
-+}
-+
- static int mtk_image_verify_header(unsigned char *ptr, int image_size,
- struct image_tool_params *params)
- {
-+ image_header_t *hdr = (image_header_t *)ptr;
- union lk_hdr *lk = (union lk_hdr *)ptr;
-
- /* nothing to verify for LK image header */
-@@ -590,6 +719,9 @@ static int mtk_image_verify_header(unsig
-
- img_size = image_size;
-
-+ if (image_get_magic(hdr) == IH_MAGIC)
-+ return mtk_image_verify_mt7621_header(ptr, 0);
-+
- if (!strcmp((char *)ptr, NAND_BOOT_NAME))
- return mtk_image_verify_nand_header(ptr, 0);
- else
-@@ -600,6 +732,7 @@ static int mtk_image_verify_header(unsig
-
- static void mtk_image_print_header(const void *ptr)
- {
-+ image_header_t *hdr = (image_header_t *)ptr;
- union lk_hdr *lk = (union lk_hdr *)ptr;
-
- if (le32_to_cpu(lk->magic) == LK_PART_MAGIC) {
-@@ -610,6 +743,11 @@ static void mtk_image_print_header(const
-
- printf("Image Type: MediaTek BootROM Loadable Image\n");
-
-+ if (image_get_magic(hdr) == IH_MAGIC) {
-+ mtk_image_verify_mt7621_header(ptr, 1);
-+ return;
-+ }
-+
- if (!strcmp((char *)ptr, NAND_BOOT_NAME))
- mtk_image_verify_nand_header(ptr, 1);
- else
-@@ -773,6 +911,45 @@ static void mtk_image_set_nand_header(vo
- filesize - 2 * le16_to_cpu(hdr_nand->pagesize) - SHA256_SUM_LEN);
- }
-
-+static void mtk_image_set_mt7621_header(void *ptr, off_t filesize,
-+ uint32_t loadaddr)
-+{
-+ image_header_t *hdr = (image_header_t *)ptr;
-+ struct mt7621_stage1_header *shdr;
-+ struct mt7621_nand_header *nhdr;
-+ uint32_t datasize, crcval;
-+
-+ datasize = filesize - image_get_header_size();
-+ nhdr = (struct mt7621_nand_header *)hdr->ih_name;
-+ shdr = (struct mt7621_stage1_header *)(ptr + image_get_header_size());
-+
-+ shdr->ep = cpu_to_be32(loadaddr);
-+ shdr->stage_size = cpu_to_be32(datasize);
-+
-+ image_set_magic(hdr, IH_MAGIC);
-+ image_set_time(hdr, time(NULL));
-+ image_set_size(hdr, datasize);
-+ image_set_load(hdr, loadaddr);
-+ image_set_ep(hdr, loadaddr);
-+ image_set_os(hdr, IH_OS_U_BOOT);
-+ image_set_arch(hdr, IH_ARCH_MIPS);
-+ image_set_type(hdr, IH_TYPE_STANDALONE);
-+ image_set_comp(hdr, IH_COMP_NONE);
-+
-+ crcval = crc32(0, (uint8_t *)shdr, datasize);
-+ image_set_dcrc(hdr, crcval);
-+
-+ strncpy(nhdr->ih_name, "MT7621 NAND", MT7621_IH_NMLEN);
-+
-+ nhdr->ih_stage_offset = cpu_to_be32(image_get_header_size());
-+
-+ crcval = crc32be_cal(hdr, image_get_header_size());
-+ nhdr->crc = cpu_to_be32(crcval);
-+
-+ crcval = crc32(0, (uint8_t *)hdr, image_get_header_size());
-+ image_set_hcrc(hdr, crcval);
-+}
-+
- static void mtk_image_set_header(void *ptr, struct stat *sbuf, int ifd,
- struct image_tool_params *params)
- {
-@@ -791,6 +968,11 @@ static void mtk_image_set_header(void *p
- img_gen = true;
- img_size = sbuf->st_size;
-
-+ if (use_mt7621_hdr) {
-+ mtk_image_set_mt7621_header(ptr, sbuf->st_size, params->addr);
-+ return;
-+ }
-+
- if (hdr_media == BRLYT_TYPE_NAND || hdr_media == BRLYT_TYPE_SNAND)
- mtk_image_set_nand_header(ptr, sbuf->st_size, params->addr);
- else
---- a/tools/mtk_image.h
-+++ b/tools/mtk_image.h
-@@ -200,4 +200,28 @@ union lk_hdr {
-
- #define LK_PART_MAGIC 0x58881688
-
-+/* MT7621 NAND SPL image header */
-+
-+#define MT7621_IH_NMLEN 12
-+#define MT7621_IH_CRC_POLYNOMIAL 0x04c11db7
-+
-+struct mt7621_nand_header {
-+ char ih_name[MT7621_IH_NMLEN];
-+ uint32_t nand_ac_timing;
-+ uint32_t ih_stage_offset;
-+ uint32_t ih_bootloader_offset;
-+ uint32_t nand_info_1_data;
-+ uint32_t crc;
-+};
-+
-+struct mt7621_stage1_header {
-+ uint32_t jump_insn[2];
-+ uint32_t ep;
-+ uint32_t stage_size;
-+ uint32_t has_stage2;
-+ uint32_t next_ep;
-+ uint32_t next_size;
-+ uint32_t next_offset;
-+};
-+
- #endif /* _MTK_IMAGE_H */
+++ /dev/null
-From e5fc4022af3cfd59e3459276305671a595ac5ff0 Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Fri, 20 May 2022 11:24:16 +0800
-Subject: [PATCH 25/25] MAINTAINERS: update maintainer for MediaTek MIPS
- platform
-
-Update maintainer for MediaTek MIPS platform
-
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- MAINTAINERS | 8 ++++++++
- 1 file changed, 8 insertions(+)
-
---- a/MAINTAINERS
-+++ b/MAINTAINERS
-@@ -1007,15 +1007,23 @@ R: GSS_MTK_Uboot_upstream <GSS_MTK_Uboot
- S: Maintained
- F: arch/mips/mach-mtmips/
- F: arch/mips/dts/mt7620.dtsi
-+F: arch/mips/dts/mt7621.dtsi
- F: arch/mips/dts/mt7620-u-boot.dtsi
-+F: arch/mips/dts/mt7621-u-boot.dtsi
- F: include/configs/mt7620.h
-+F: include/configs/mt7621.h
- F: include/dt-bindings/clock/mt7620-clk.h
-+F: include/dt-bindings/clock/mt7621-clk.h
- F: include/dt-bindings/clock/mt7628-clk.h
- F: include/dt-bindings/reset/mt7620-reset.h
-+F: include/dt-bindings/reset/mt7621-reset.h
- F: include/dt-bindings/reset/mt7628-reset.h
- F: drivers/clk/mtmips/
- F: drivers/pinctrl/mtmips/
- F: drivers/gpio/mt7620_gpio.c
-+F: drivers/mtd/nand/raw/mt7621_nand.c
-+F: drivers/mtd/nand/raw/mt7621_nand.h
-+F: drivers/mtd/nand/raw/mt7621_nand_spl.c
- F: drivers/net/mt7620-eth.c
- F: drivers/phy/mt7620-usb-phy.c
- F: drivers/reset/reset-mtmips.c
+++ /dev/null
-From a3ba6adb70c91ec3b9312c3a025faa44acd39cfa Mon Sep 17 00:00:00 2001
-From: Weijie Gao <weijie.gao@mediatek.com>
-Date: Wed, 13 Jul 2022 11:16:39 +0800
-Subject: [PATCH] arm: dts: mt7622: remove default pinctrl of uart0
-
-Currently u-boot running on mt7622 will print an warning log at beginning:
-> serial_mtk serial@11002000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
-
-It turns out that the pinctrl uclass can't work properly in board_f stage.
-
-Since the uart0 is the default UART device used by bootrom, and will be
-initialized in both bootrom and tf-a bl2. It's ok not to setup pinctrl for
-uart0 in u-boot.
-
-This patch removes the default pinctrl of uart0 to suppress the unwanted
-warning.
-
-Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
----
- arch/arm/dts/mt7622-bananapi-bpi-r64.dts | 2 --
- arch/arm/dts/mt7622-rfb.dts | 2 --
- 2 files changed, 4 deletions(-)
-
---- a/arch/arm/dts/mt7622-bananapi-bpi-r64.dts
-+++ b/arch/arm/dts/mt7622-bananapi-bpi-r64.dts
-@@ -182,8 +182,6 @@
- };
-
- &uart0 {
-- pinctrl-names = "default";
-- pinctrl-0 = <&uart0_pins>;
- status = "okay";
- };
-
---- a/arch/arm/dts/mt7622-rfb.dts
-+++ b/arch/arm/dts/mt7622-rfb.dts
-@@ -189,8 +189,6 @@
- };
-
- &uart0 {
-- pinctrl-names = "default";
-- pinctrl-0 = <&uart0_pins>;
- status = "okay";
- };
-
+++ /dev/null
-From b62450cf229c50ad2ce819dd02a09726909cc89a Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Pali=20Roh=C3=A1r?= <pali@kernel.org>
-Date: Fri, 27 May 2022 22:15:24 +0200
-Subject: [PATCH] serial: Replace CONFIG_DEBUG_UART_BASE by
- CONFIG_VAL(DEBUG_UART_BASE)
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-CONFIG_VAL(DEBUG_UART_BASE) expands to CONFIG_DEBUG_UART_BASE or
-CONFIG_SPL_DEBUG_UART_BASE or CONFIG_TPL_DEBUG_UART_BASE and allows boards
-to set different values for SPL, TPL and U-Boot Proper.
-
-For ns16550 driver this support is there since commit d293759d55cc
-("serial: ns16550: Add support for SPL_DEBUG_UART_BASE").
-
-Signed-off-by: Pali Rohár <pali@kernel.org>
----
- arch/arm/mach-uniphier/debug-uart/debug-uart.c | 4 ++--
- arch/x86/cpu/apollolake/cpu_common.c | 2 +-
- board/eets/pdu001/board.c | 2 +-
- drivers/serial/altera_jtag_uart.c | 2 +-
- drivers/serial/altera_uart.c | 4 ++--
- drivers/serial/atmel_usart.c | 4 ++--
- drivers/serial/serial_ar933x.c | 4 ++--
- drivers/serial/serial_arc.c | 4 ++--
- drivers/serial/serial_bcm6345.c | 4 ++--
- drivers/serial/serial_linflexuart.c | 4 ++--
- drivers/serial/serial_meson.c | 2 +-
- drivers/serial/serial_msm_geni.c | 6 +++---
- drivers/serial/serial_mt7620.c | 4 ++--
- drivers/serial/serial_mtk.c | 4 ++--
- drivers/serial/serial_mvebu_a3700.c | 4 ++--
- drivers/serial/serial_mxc.c | 4 ++--
- drivers/serial/serial_omap.c | 4 ++--
- drivers/serial/serial_pic32.c | 4 ++--
- drivers/serial/serial_pl01x.c | 4 ++--
- drivers/serial/serial_s5p.c | 4 ++--
- drivers/serial/serial_sifive.c | 4 ++--
- drivers/serial/serial_stm32.c | 4 ++--
- drivers/serial/serial_xuartlite.c | 4 ++--
- drivers/serial/serial_zynq.c | 4 ++--
- 24 files changed, 45 insertions(+), 45 deletions(-)
-
---- a/arch/arm/mach-uniphier/debug-uart/debug-uart.c
-+++ b/arch/arm/mach-uniphier/debug-uart/debug-uart.c
-@@ -18,7 +18,7 @@
-
- static void _debug_uart_putc(int c)
- {
-- void __iomem *base = (void __iomem *)CONFIG_DEBUG_UART_BASE;
-+ void __iomem *base = (void __iomem *)CONFIG_VAL(DEBUG_UART_BASE);
-
- while (!(readl(base + UNIPHIER_UART_LSR) & UART_LSR_THRE))
- ;
-@@ -57,7 +57,7 @@ void sg_set_iectrl(unsigned int pin)
- void _debug_uart_init(void)
- {
- #ifdef CONFIG_SPL_BUILD
-- void __iomem *base = (void __iomem *)CONFIG_DEBUG_UART_BASE;
-+ void __iomem *base = (void __iomem *)CONFIG_VAL(DEBUG_UART_BASE);
- unsigned int divisor;
-
- switch (uniphier_get_soc_id()) {
---- a/arch/x86/cpu/apollolake/cpu_common.c
-+++ b/arch/x86/cpu/apollolake/cpu_common.c
-@@ -72,7 +72,7 @@ static void pch_uart_init(void)
- }
-
- #ifdef CONFIG_DEBUG_UART
-- apl_uart_init(PCH_DEV_UART, CONFIG_DEBUG_UART_BASE);
-+ apl_uart_init(PCH_DEV_UART, CONFIG_VAL(DEBUG_UART_BASE));
- #endif
- }
-
---- a/board/eets/pdu001/board.c
-+++ b/board/eets/pdu001/board.c
-@@ -273,7 +273,7 @@ void board_debug_uart_init(void)
- setup_early_clocks();
-
- /* done by pin controller driver if not debugging */
-- enable_uart_pin_mux(CONFIG_DEBUG_UART_BASE);
-+ enable_uart_pin_mux(CONFIG_VAL(DEBUG_UART_BASE));
- }
- #endif
-
---- a/drivers/serial/altera_jtag_uart.c
-+++ b/drivers/serial/altera_jtag_uart.c
-@@ -134,7 +134,7 @@ static inline void _debug_uart_init(void
-
- static inline void _debug_uart_putc(int ch)
- {
-- struct altera_jtaguart_regs *regs = (void *)CONFIG_DEBUG_UART_BASE;
-+ struct altera_jtaguart_regs *regs = (void *)CONFIG_VAL(DEBUG_UART_BASE);
-
- while (1) {
- u32 st = readl(®s->control);
---- a/drivers/serial/altera_uart.c
-+++ b/drivers/serial/altera_uart.c
-@@ -123,7 +123,7 @@ U_BOOT_DRIVER(altera_uart) = {
-
- static inline void _debug_uart_init(void)
- {
-- struct altera_uart_regs *regs = (void *)CONFIG_DEBUG_UART_BASE;
-+ struct altera_uart_regs *regs = (void *)CONFIG_VAL(DEBUG_UART_BASE);
- u32 div;
-
- div = (CONFIG_DEBUG_UART_CLOCK / CONFIG_BAUDRATE) - 1;
-@@ -132,7 +132,7 @@ static inline void _debug_uart_init(void
-
- static inline void _debug_uart_putc(int ch)
- {
-- struct altera_uart_regs *regs = (void *)CONFIG_DEBUG_UART_BASE;
-+ struct altera_uart_regs *regs = (void *)CONFIG_VAL(DEBUG_UART_BASE);
-
- while (1) {
- u32 st = readl(®s->status);
---- a/drivers/serial/atmel_usart.c
-+++ b/drivers/serial/atmel_usart.c
-@@ -319,14 +319,14 @@ U_BOOT_DRIVER(serial_atmel) = {
- #ifdef CONFIG_DEBUG_UART_ATMEL
- static inline void _debug_uart_init(void)
- {
-- atmel_usart3_t *usart = (atmel_usart3_t *)CONFIG_DEBUG_UART_BASE;
-+ atmel_usart3_t *usart = (atmel_usart3_t *)CONFIG_VAL(DEBUG_UART_BASE);
-
- _atmel_serial_init(usart, CONFIG_DEBUG_UART_CLOCK, CONFIG_BAUDRATE);
- }
-
- static inline void _debug_uart_putc(int ch)
- {
-- atmel_usart3_t *usart = (atmel_usart3_t *)CONFIG_DEBUG_UART_BASE;
-+ atmel_usart3_t *usart = (atmel_usart3_t *)CONFIG_VAL(DEBUG_UART_BASE);
-
- while (!(readl(&usart->csr) & USART3_BIT(TXRDY)))
- ;
---- a/drivers/serial/serial_ar933x.c
-+++ b/drivers/serial/serial_ar933x.c
-@@ -199,7 +199,7 @@ U_BOOT_DRIVER(serial_ar933x) = {
-
- static inline void _debug_uart_init(void)
- {
-- void __iomem *regs = (void *)CONFIG_DEBUG_UART_BASE;
-+ void __iomem *regs = (void *)CONFIG_VAL(DEBUG_UART_BASE);
- u32 val, scale, step;
-
- /*
-@@ -227,7 +227,7 @@ static inline void _debug_uart_init(void
-
- static inline void _debug_uart_putc(int c)
- {
-- void __iomem *regs = (void *)CONFIG_DEBUG_UART_BASE;
-+ void __iomem *regs = (void *)CONFIG_VAL(DEBUG_UART_BASE);
- u32 data;
-
- do {
---- a/drivers/serial/serial_arc.c
-+++ b/drivers/serial/serial_arc.c
-@@ -137,7 +137,7 @@ U_BOOT_DRIVER(serial_arc) = {
-
- static inline void _debug_uart_init(void)
- {
-- struct arc_serial_regs *regs = (struct arc_serial_regs *)CONFIG_DEBUG_UART_BASE;
-+ struct arc_serial_regs *regs = (struct arc_serial_regs *)CONFIG_VAL(DEBUG_UART_BASE);
- int arc_console_baud = CONFIG_DEBUG_UART_CLOCK / (CONFIG_BAUDRATE * 4) - 1;
-
- writeb(arc_console_baud & 0xff, ®s->baudl);
-@@ -146,7 +146,7 @@ static inline void _debug_uart_init(void
-
- static inline void _debug_uart_putc(int c)
- {
-- struct arc_serial_regs *regs = (struct arc_serial_regs *)CONFIG_DEBUG_UART_BASE;
-+ struct arc_serial_regs *regs = (struct arc_serial_regs *)CONFIG_VAL(DEBUG_UART_BASE);
-
- while (!(readb(®s->status) & UART_TXEMPTY))
- ;
---- a/drivers/serial/serial_bcm6345.c
-+++ b/drivers/serial/serial_bcm6345.c
-@@ -269,7 +269,7 @@ U_BOOT_DRIVER(bcm6345_serial) = {
- #ifdef CONFIG_DEBUG_UART_BCM6345
- static inline void _debug_uart_init(void)
- {
-- void __iomem *base = (void __iomem *)CONFIG_DEBUG_UART_BASE;
-+ void __iomem *base = (void __iomem *)CONFIG_VAL(DEBUG_UART_BASE);
-
- bcm6345_serial_init(base, CONFIG_DEBUG_UART_CLOCK, CONFIG_BAUDRATE);
- }
-@@ -285,7 +285,7 @@ static inline void wait_xfered(void __io
-
- static inline void _debug_uart_putc(int ch)
- {
-- void __iomem *base = (void __iomem *)CONFIG_DEBUG_UART_BASE;
-+ void __iomem *base = (void __iomem *)CONFIG_VAL(DEBUG_UART_BASE);
-
- wait_xfered(base);
- writel(ch, base + UART_FIFO_REG);
---- a/drivers/serial/serial_linflexuart.c
-+++ b/drivers/serial/serial_linflexuart.c
-@@ -201,14 +201,14 @@ U_BOOT_DRIVER(serial_linflex) = {
-
- static inline void _debug_uart_init(void)
- {
-- struct linflex_fsl *base = (struct linflex_fsl *)CONFIG_DEBUG_UART_BASE;
-+ struct linflex_fsl *base = (struct linflex_fsl *)CONFIG_VAL(DEBUG_UART_BASE);
-
- linflex_serial_init_internal(base);
- }
-
- static inline void _debug_uart_putc(int ch)
- {
-- struct linflex_fsl *base = (struct linflex_fsl *)CONFIG_DEBUG_UART_BASE;
-+ struct linflex_fsl *base = (struct linflex_fsl *)CONFIG_VAL(DEBUG_UART_BASE);
-
- /* XXX: Is this OK? Should this use the non-DM version? */
- _linflex_serial_putc(base, ch);
---- a/drivers/serial/serial_meson.c
-+++ b/drivers/serial/serial_meson.c
-@@ -182,7 +182,7 @@ static inline void _debug_uart_init(void
-
- static inline void _debug_uart_putc(int ch)
- {
-- struct meson_uart *regs = (struct meson_uart *)CONFIG_DEBUG_UART_BASE;
-+ struct meson_uart *regs = (struct meson_uart *)CONFIG_VAL(DEBUG_UART_BASE);
-
- while (readl(®s->status) & AML_UART_TX_FULL)
- ;
---- a/drivers/serial/serial_msm_geni.c
-+++ b/drivers/serial/serial_msm_geni.c
-@@ -569,7 +569,7 @@ U_BOOT_DRIVER(serial_msm_geni) = {
- #ifdef CONFIG_DEBUG_UART_MSM_GENI
-
- static struct msm_serial_data init_serial_data = {
-- .base = CONFIG_DEBUG_UART_BASE
-+ .base = CONFIG_VAL(DEBUG_UART_BASE)
- };
-
- /* Serial dumb device, to reuse driver code */
-@@ -587,7 +587,7 @@ static struct udevice init_dev = {
-
- static inline void _debug_uart_init(void)
- {
-- phys_addr_t base = CONFIG_DEBUG_UART_BASE;
-+ phys_addr_t base = CONFIG_VAL(DEBUG_UART_BASE);
-
- geni_serial_init(&init_dev);
- geni_serial_baud(base, CLK_DIV, CONFIG_BAUDRATE);
-@@ -596,7 +596,7 @@ static inline void _debug_uart_init(void
-
- static inline void _debug_uart_putc(int ch)
- {
-- phys_addr_t base = CONFIG_DEBUG_UART_BASE;
-+ phys_addr_t base = CONFIG_VAL(DEBUG_UART_BASE);
-
- writel(DEF_TX_WM, base + SE_GENI_TX_WATERMARK_REG);
- qcom_geni_serial_setup_tx(base, 1);
---- a/drivers/serial/serial_mt7620.c
-+++ b/drivers/serial/serial_mt7620.c
-@@ -220,7 +220,7 @@ static inline void _debug_uart_init(void
- {
- struct mt7620_serial_plat plat;
-
-- plat.regs = (void *)CONFIG_DEBUG_UART_BASE;
-+ plat.regs = (void *)CONFIG_VAL(DEBUG_UART_BASE);
- plat.clock = CONFIG_DEBUG_UART_CLOCK;
-
- writel(0, &plat.regs->ier);
-@@ -233,7 +233,7 @@ static inline void _debug_uart_init(void
- static inline void _debug_uart_putc(int ch)
- {
- struct mt7620_serial_regs __iomem *regs =
-- (void *)CONFIG_DEBUG_UART_BASE;
-+ (void *)CONFIG_VAL(DEBUG_UART_BASE);
-
- while (!(readl(®s->lsr) & UART_LSR_THRE))
- ;
---- a/drivers/serial/serial_mtk.c
-+++ b/drivers/serial/serial_mtk.c
-@@ -426,7 +426,7 @@ static inline void _debug_uart_init(void
- {
- struct mtk_serial_priv priv;
-
-- priv.regs = (void *) CONFIG_DEBUG_UART_BASE;
-+ priv.regs = (void *) CONFIG_VAL(DEBUG_UART_BASE);
- priv.clock = CONFIG_DEBUG_UART_CLOCK;
-
- writel(0, &priv.regs->ier);
-@@ -439,7 +439,7 @@ static inline void _debug_uart_init(void
- static inline void _debug_uart_putc(int ch)
- {
- struct mtk_serial_regs __iomem *regs =
-- (void *) CONFIG_DEBUG_UART_BASE;
-+ (void *) CONFIG_VAL(DEBUG_UART_BASE);
-
- while (!(readl(®s->lsr) & UART_LSR_THRE))
- ;
---- a/drivers/serial/serial_mvebu_a3700.c
-+++ b/drivers/serial/serial_mvebu_a3700.c
-@@ -321,7 +321,7 @@ U_BOOT_DRIVER(serial_mvebu) = {
-
- static inline void _debug_uart_init(void)
- {
-- void __iomem *base = (void __iomem *)CONFIG_DEBUG_UART_BASE;
-+ void __iomem *base = (void __iomem *)CONFIG_VAL(DEBUG_UART_BASE);
- u32 parent_rate, divider;
-
- /* reset FIFOs */
-@@ -349,7 +349,7 @@ static inline void _debug_uart_init(void
-
- static inline void _debug_uart_putc(int ch)
- {
-- void __iomem *base = (void __iomem *)CONFIG_DEBUG_UART_BASE;
-+ void __iomem *base = (void __iomem *)CONFIG_VAL(DEBUG_UART_BASE);
-
- while (readl(base + UART_STATUS_REG) & UART_STATUS_TXFIFO_FULL)
- ;
---- a/drivers/serial/serial_mxc.c
-+++ b/drivers/serial/serial_mxc.c
-@@ -372,7 +372,7 @@ U_BOOT_DRIVER(serial_mxc) = {
-
- static inline void _debug_uart_init(void)
- {
-- struct mxc_uart *base = (struct mxc_uart *)CONFIG_DEBUG_UART_BASE;
-+ struct mxc_uart *base = (struct mxc_uart *)CONFIG_VAL(DEBUG_UART_BASE);
-
- _mxc_serial_init(base, false);
- _mxc_serial_setbrg(base, CONFIG_DEBUG_UART_CLOCK,
-@@ -381,7 +381,7 @@ static inline void _debug_uart_init(void
-
- static inline void _debug_uart_putc(int ch)
- {
-- struct mxc_uart *base = (struct mxc_uart *)CONFIG_DEBUG_UART_BASE;
-+ struct mxc_uart *base = (struct mxc_uart *)CONFIG_VAL(DEBUG_UART_BASE);
-
- while (!(readl(&base->ts) & UTS_TXEMPTY))
- WATCHDOG_RESET();
---- a/drivers/serial/serial_omap.c
-+++ b/drivers/serial/serial_omap.c
-@@ -66,7 +66,7 @@ static inline int serial_in_shift(void *
-
- static inline void _debug_uart_init(void)
- {
-- struct ns16550 *com_port = (struct ns16550 *)CONFIG_DEBUG_UART_BASE;
-+ struct ns16550 *com_port = (struct ns16550 *)CONFIG_VAL(DEBUG_UART_BASE);
- int baud_divisor;
-
- baud_divisor = ns16550_calc_divisor(com_port, CONFIG_DEBUG_UART_CLOCK,
-@@ -85,7 +85,7 @@ static inline void _debug_uart_init(void
-
- static inline void _debug_uart_putc(int ch)
- {
-- struct ns16550 *com_port = (struct ns16550 *)CONFIG_DEBUG_UART_BASE;
-+ struct ns16550 *com_port = (struct ns16550 *)CONFIG_VAL(DEBUG_UART_BASE);
-
- while (!(serial_din(&com_port->lsr) & UART_LSR_THRE))
- ;
---- a/drivers/serial/serial_pic32.c
-+++ b/drivers/serial/serial_pic32.c
-@@ -187,14 +187,14 @@ U_BOOT_DRIVER(pic32_serial) = {
-
- static inline void _debug_uart_init(void)
- {
-- void __iomem *base = (void __iomem *)CONFIG_DEBUG_UART_BASE;
-+ void __iomem *base = (void __iomem *)CONFIG_VAL(DEBUG_UART_BASE);
-
- pic32_serial_init(base, CONFIG_DEBUG_UART_CLOCK, CONFIG_BAUDRATE);
- }
-
- static inline void _debug_uart_putc(int ch)
- {
-- writel(ch, CONFIG_DEBUG_UART_BASE + U_TXR);
-+ writel(ch, CONFIG_VAL(DEBUG_UART_BASE) + U_TXR);
- }
-
- DEBUG_UART_FUNCS
---- a/drivers/serial/serial_pl01x.c
-+++ b/drivers/serial/serial_pl01x.c
-@@ -403,7 +403,7 @@ U_BOOT_DRIVER(serial_pl01x) = {
- static void _debug_uart_init(void)
- {
- #ifndef CONFIG_DEBUG_UART_SKIP_INIT
-- struct pl01x_regs *regs = (struct pl01x_regs *)CONFIG_DEBUG_UART_BASE;
-+ struct pl01x_regs *regs = (struct pl01x_regs *)CONFIG_VAL(DEBUG_UART_BASE);
- enum pl01x_type type;
-
- if (IS_ENABLED(CONFIG_DEBUG_UART_PL011))
-@@ -419,7 +419,7 @@ static void _debug_uart_init(void)
-
- static inline void _debug_uart_putc(int ch)
- {
-- struct pl01x_regs *regs = (struct pl01x_regs *)CONFIG_DEBUG_UART_BASE;
-+ struct pl01x_regs *regs = (struct pl01x_regs *)CONFIG_VAL(DEBUG_UART_BASE);
-
- while (pl01x_putc(regs, ch) == -EAGAIN)
- ;
---- a/drivers/serial/serial_s5p.c
-+++ b/drivers/serial/serial_s5p.c
-@@ -276,7 +276,7 @@ static inline void _debug_uart_init(void
- if (IS_ENABLED(CONFIG_DEBUG_UART_SKIP_INIT))
- return;
-
-- struct s5p_uart *uart = (struct s5p_uart *)CONFIG_DEBUG_UART_BASE;
-+ struct s5p_uart *uart = (struct s5p_uart *)CONFIG_VAL(DEBUG_UART_BASE);
-
- s5p_serial_init(uart);
- #if CONFIG_IS_ENABLED(ARCH_APPLE)
-@@ -288,7 +288,7 @@ static inline void _debug_uart_init(void
-
- static inline void _debug_uart_putc(int ch)
- {
-- struct s5p_uart *uart = (struct s5p_uart *)CONFIG_DEBUG_UART_BASE;
-+ struct s5p_uart *uart = (struct s5p_uart *)CONFIG_VAL(DEBUG_UART_BASE);
-
- #if CONFIG_IS_ENABLED(ARCH_APPLE)
- while (readl(&uart->ufstat) & S5L_TX_FIFO_FULL);
---- a/drivers/serial/serial_sifive.c
-+++ b/drivers/serial/serial_sifive.c
-@@ -212,7 +212,7 @@ U_BOOT_DRIVER(serial_sifive) = {
- static inline void _debug_uart_init(void)
- {
- struct uart_sifive *regs =
-- (struct uart_sifive *)CONFIG_DEBUG_UART_BASE;
-+ (struct uart_sifive *)CONFIG_VAL(DEBUG_UART_BASE);
-
- _sifive_serial_setbrg(regs, CONFIG_DEBUG_UART_CLOCK,
- CONFIG_BAUDRATE);
-@@ -222,7 +222,7 @@ static inline void _debug_uart_init(void
- static inline void _debug_uart_putc(int ch)
- {
- struct uart_sifive *regs =
-- (struct uart_sifive *)CONFIG_DEBUG_UART_BASE;
-+ (struct uart_sifive *)CONFIG_VAL(DEBUG_UART_BASE);
-
- while (_sifive_serial_putc(regs, ch) == -EAGAIN)
- WATCHDOG_RESET();
---- a/drivers/serial/serial_stm32.c
-+++ b/drivers/serial/serial_stm32.c
-@@ -270,7 +270,7 @@ static inline struct stm32_uart_info *_d
-
- static inline void _debug_uart_init(void)
- {
-- fdt_addr_t base = CONFIG_DEBUG_UART_BASE;
-+ fdt_addr_t base = CONFIG_VAL(DEBUG_UART_BASE);
- struct stm32_uart_info *uart_info = _debug_uart_info();
-
- _stm32_serial_init(base, uart_info);
-@@ -281,7 +281,7 @@ static inline void _debug_uart_init(void
-
- static inline void _debug_uart_putc(int c)
- {
-- fdt_addr_t base = CONFIG_DEBUG_UART_BASE;
-+ fdt_addr_t base = CONFIG_VAL(DEBUG_UART_BASE);
- struct stm32_uart_info *uart_info = _debug_uart_info();
-
- while (_stm32_serial_putc(base, uart_info, c) == -EAGAIN)
---- a/drivers/serial/serial_xuartlite.c
-+++ b/drivers/serial/serial_xuartlite.c
-@@ -143,7 +143,7 @@ U_BOOT_DRIVER(serial_uartlite) = {
-
- static inline void _debug_uart_init(void)
- {
-- struct uartlite *regs = (struct uartlite *)CONFIG_DEBUG_UART_BASE;
-+ struct uartlite *regs = (struct uartlite *)CONFIG_VAL(DEBUG_UART_BASE);
- int ret;
-
- uart_out32(®s->control, 0);
-@@ -159,7 +159,7 @@ static inline void _debug_uart_init(void
-
- static inline void _debug_uart_putc(int ch)
- {
-- struct uartlite *regs = (struct uartlite *)CONFIG_DEBUG_UART_BASE;
-+ struct uartlite *regs = (struct uartlite *)CONFIG_VAL(DEBUG_UART_BASE);
-
- while (uart_in32(®s->status) & SR_TX_FIFO_FULL)
- ;
---- a/drivers/serial/serial_zynq.c
-+++ b/drivers/serial/serial_zynq.c
-@@ -295,7 +295,7 @@ U_BOOT_DRIVER(serial_zynq) = {
- #ifdef CONFIG_DEBUG_UART_ZYNQ
- static inline void _debug_uart_init(void)
- {
-- struct uart_zynq *regs = (struct uart_zynq *)CONFIG_DEBUG_UART_BASE;
-+ struct uart_zynq *regs = (struct uart_zynq *)CONFIG_VAL(DEBUG_UART_BASE);
-
- _uart_zynq_serial_init(regs);
- _uart_zynq_serial_setbrg(regs, CONFIG_DEBUG_UART_CLOCK,
-@@ -304,7 +304,7 @@ static inline void _debug_uart_init(void
-
- static inline void _debug_uart_putc(int ch)
- {
-- struct uart_zynq *regs = (struct uart_zynq *)CONFIG_DEBUG_UART_BASE;
-+ struct uart_zynq *regs = (struct uart_zynq *)CONFIG_VAL(DEBUG_UART_BASE);
-
- while (_uart_zynq_serial_putc(regs, ch) == -EAGAIN)
- WATCHDOG_RESET();
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
-@@ -1205,6 +1205,12 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
+@@ -1233,6 +1233,12 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
mt7622-bananapi-bpi-r64.dtb \
mt7623n-bananapi-bpi-r2.dtb \
mt7629-rfb.dtb \
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
-@@ -1205,6 +1205,9 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
+@@ -1233,6 +1233,9 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
mt7622-bananapi-bpi-r64.dtb \
mt7623n-bananapi-bpi-r2.dtb \
mt7629-rfb.dtb \
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
-@@ -262,6 +262,14 @@ config MTK_SNFI_SPI
+@@ -276,6 +276,14 @@ config MTK_SNFI_SPI
used to access SPI memory devices like SPI-NOR or SPI-NAND on
platforms embedding this IP core, like MT7622/M7629.
select CLK_ARMADA_3720
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
-@@ -41,6 +41,7 @@ obj-$(CONFIG_MPC8XX_SPI) += mpc8xx_spi.o
+@@ -43,6 +43,7 @@ obj-$(CONFIG_MPC8XX_SPI) += mpc8xx_spi.o
obj-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o
obj-$(CONFIG_MTK_SNFI_SPI) += mtk_snfi_spi.o
obj-$(CONFIG_MTK_SNOR) += mtk_snor.o
obj-$(CONFIG_SYS_I2C_MXC) += mxc_i2c.o
+obj-$(CONFIG_SYS_I2C_MTK) += mtk_i2c.o
obj-$(CONFIG_SYS_I2C_NEXELL) += nx_i2c.o
+ obj-$(CONFIG_SYS_I2C_NPCM) += npcm_i2c.o
obj-$(CONFIG_SYS_I2C_OCORES) += ocores_i2c.o
- obj-$(CONFIG_SYS_I2C_OCTEON) += octeon_i2c.o
--- /dev/null
+++ b/drivers/i2c/mtk_i2c.c
@@ -0,0 +1,822 @@
+obj-$(CONFIG_ARCH_MEDIATEK) += mtk_cpu.o
obj-$(CONFIG_CPU_MPC83XX) += mpc83xx_cpu.o
obj-$(CONFIG_CPU_RISCV) += riscv_cpu.o
- obj-$(CONFIG_SANDBOX) += cpu_sandbox.o
+ obj-$(CONFIG_CPU_MICROBLAZE) += microblaze_cpu.o
--- /dev/null
+++ b/drivers/cpu/mtk_cpu.c
@@ -0,0 +1,106 @@
--- a/MAINTAINERS
+++ b/MAINTAINERS
-@@ -340,20 +340,26 @@ F: doc/device-tree-bindings/phy/phy-mtk-
+@@ -356,20 +356,26 @@ F: doc/device-tree-bindings/phy/phy-mtk-
F: doc/device-tree-bindings/usb/mediatek,*
F: doc/README.mediatek
F: drivers/clk/mediatek/
+F: tools/mtk_nand_headers.h
N: mediatek
- ARM MICROCHIP/ATMEL AT91
+ ARM METHODE SUPPORT
+++ /dev/null
-From baef13ec9d592a27b5d3bf03967bfd2bebd65157 Mon Sep 17 00:00:00 2001
-From: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
-Date: Wed, 25 May 2022 10:47:12 +0530
-Subject: [PATCH] mtd: spi-nor-ids: Add support for flashes tested by xilinx
-
-Add support for various flashes from below manufacturers which are tested
-by xilinx for years.
-
-EON:
- en25q128b
-GIGA:
- gd25lx256e
-ISSI:
- is25lp008
- is25lp016
- is25lp01g
- is25wp008
- is25wp016
- is25wp01g
- is25wx256
-MACRONIX:
- mx25u51245f
- mx66u1g45g
- mx66l2g45g
-MICRON:
- mt35xl512aba
- mt35xu01g
-SPANSION:
- s70fs01gs_256k
-SST:
- sst26wf016b
-WINBOND:
- w25q16dw
- w25q16jv
- w25q512jv
- w25q32bv
- w25h02jv
-
-Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
-Link: https://lore.kernel.org/r/1653455832-14763-1-git-send-email-ashok.reddy.soma@xilinx.com
-Signed-off-by: Michal Simek <michal.simek@amd.com>
----
- drivers/mtd/spi/spi-nor-ids.c | 37 +++++++++++++++++++++++++++++++++++
- 1 file changed, 37 insertions(+)
-
---- a/drivers/mtd/spi/spi-nor-ids.c
-+++ b/drivers/mtd/spi/spi-nor-ids.c
-@@ -82,6 +82,7 @@ const struct flash_info spi_nor_ids[] =
- /* EON -- en25xxx */
- { INFO("en25q32b", 0x1c3016, 0, 64 * 1024, 64, 0) },
- { INFO("en25q64", 0x1c3017, 0, 64 * 1024, 128, SECT_4K) },
-+ { INFO("en25q128b", 0x1c3018, 0, 64 * 1024, 256, 0) },
- { INFO("en25qh128", 0x1c7018, 0, 64 * 1024, 256, 0) },
- { INFO("en25s64", 0x1c3817, 0, 64 * 1024, 128, SECT_4K) },
- #endif
-@@ -127,11 +128,17 @@ const struct flash_info spi_nor_ids[] =
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
-+ {
-+ INFO("gd25lx256e", 0xc86819, 0, 64 * 1024, 512,
-+ SECT_4K | SPI_NOR_OCTAL_READ | SPI_NOR_4B_OPCODES)
-+ },
- #endif
- #ifdef CONFIG_SPI_FLASH_ISSI /* ISSI */
- /* ISSI */
- { INFO("is25lq040b", 0x9d4013, 0, 64 * 1024, 8,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
-+ { INFO("is25lp008", 0x9d6014, 0, 64 * 1024, 16, SPI_NOR_QUAD_READ) },
-+ { INFO("is25lp016", 0x9d6015, 0, 64 * 1024, 32, SPI_NOR_QUAD_READ) },
- { INFO("is25lp032", 0x9d6016, 0, 64 * 1024, 64, 0) },
- { INFO("is25lp064", 0x9d6017, 0, 64 * 1024, 128, 0) },
- { INFO("is25lp128", 0x9d6018, 0, 64 * 1024, 256,
-@@ -140,6 +147,10 @@ const struct flash_info spi_nor_ids[] =
- SECT_4K | SPI_NOR_DUAL_READ) },
- { INFO("is25lp512", 0x9d601a, 0, 64 * 1024, 1024,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
-+ { INFO("is25lp01g", 0x9d601b, 0, 64 * 1024, 2048,
-+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
-+ { INFO("is25wp008", 0x9d7014, 0, 64 * 1024, 16, SPI_NOR_QUAD_READ) },
-+ { INFO("is25wp016", 0x9d7015, 0, 64 * 1024, 32, SPI_NOR_QUAD_READ) },
- { INFO("is25wp032", 0x9d7016, 0, 64 * 1024, 64,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { INFO("is25wp064", 0x9d7017, 0, 64 * 1024, 128,
-@@ -151,6 +162,10 @@ const struct flash_info spi_nor_ids[] =
- SPI_NOR_4B_OPCODES) },
- { INFO("is25wp512", 0x9d701a, 0, 64 * 1024, 1024,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
-+ { INFO("is25wp01g", 0x9d701b, 0, 64 * 1024, 2048,
-+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
-+ { INFO("is25wx256", 0x9d5b19, 0, 128 * 1024, 256,
-+ SECT_4K | USE_FSR | SPI_NOR_OCTAL_READ | SPI_NOR_4B_OPCODES) },
- #endif
- #ifdef CONFIG_SPI_FLASH_MACRONIX /* MACRONIX */
- /* Macronix */
-@@ -176,8 +191,11 @@ const struct flash_info spi_nor_ids[] =
- { INFO("mx25l25655e", 0xc22619, 0, 64 * 1024, 512, 0) },
- { INFO("mx66l51235l", 0xc2201a, 0, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
- { INFO("mx66u51235f", 0xc2253a, 0, 64 * 1024, 1024, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx25u51245f", 0xc2953a, 0, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx66u1g45g", 0xc2253b, 0, 64 * 1024, 2048, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
- { INFO("mx66u2g45g", 0xc2253c, 0, 64 * 1024, 4096, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
- { INFO("mx66l1g45g", 0xc2201b, 0, 64 * 1024, 2048, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
-+ { INFO("mx66l2g45g", 0xc2201c, 0, 64 * 1024, 4096, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
- { INFO("mx25l1633e", 0xc22415, 0, 64 * 1024, 32, SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES | SECT_4K) },
- { INFO("mx25r6435f", 0xc22817, 0, 64 * 1024, 128, SECT_4K) },
- { INFO("mx66uw2g345g", 0xc2943c, 0, 64 * 1024, 4096, SECT_4K | SPI_NOR_OCTAL_READ | SPI_NOR_4B_OPCODES) },
-@@ -208,8 +226,10 @@ const struct flash_info spi_nor_ids[] =
- { INFO("mt25qu02g", 0x20bb22, 0, 64 * 1024, 4096, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
- { INFO("mt25ql02g", 0x20ba22, 0, 64 * 1024, 4096, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE | SPI_NOR_4B_OPCODES) },
- #ifdef CONFIG_SPI_FLASH_MT35XU
-+ { INFO("mt35xl512aba", 0x2c5a1a, 0, 128 * 1024, 512, USE_FSR | SPI_NOR_OCTAL_READ | SPI_NOR_4B_OPCODES | SPI_NOR_OCTAL_DTR_READ) },
- { INFO("mt35xu512aba", 0x2c5b1a, 0, 128 * 1024, 512, USE_FSR | SPI_NOR_OCTAL_READ | SPI_NOR_4B_OPCODES | SPI_NOR_OCTAL_DTR_READ) },
- #endif /* CONFIG_SPI_FLASH_MT35XU */
-+ { INFO6("mt35xu01g", 0x2c5b1b, 0x104100, 128 * 1024, 1024, USE_FSR | SPI_NOR_OCTAL_READ | SPI_NOR_4B_OPCODES) },
- { INFO("mt35xu02g", 0x2c5b1c, 0, 128 * 1024, 2048, USE_FSR | SPI_NOR_OCTAL_READ | SPI_NOR_4B_OPCODES) },
- #endif
- #ifdef CONFIG_SPI_FLASH_SPANSION /* SPANSION */
-@@ -225,6 +245,7 @@ const struct flash_info spi_nor_ids[] =
- { INFO("s25fl512s_256k", 0x010220, 0x4d00, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { INFO("s25fl512s_64k", 0x010220, 0x4d01, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
- { INFO("s25fl512s_512k", 0x010220, 0x4f00, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
-+ { INFO("s70fs01gs_256k", 0x010221, 0x4d00, 256 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { INFO("s25sl12800", 0x012018, 0x0300, 256 * 1024, 64, 0) },
- { INFO("s25sl12801", 0x012018, 0x0301, 64 * 1024, 256, 0) },
- { INFO6("s25fl128s", 0x012018, 0x4d0180, 64 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR) },
-@@ -275,6 +296,7 @@ const struct flash_info spi_nor_ids[] =
- { INFO("sst25wf040", 0xbf2504, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) },
- { INFO("sst25wf080", 0xbf2505, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) },
- { INFO("sst26vf064b", 0xbf2643, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_HAS_SST26LOCK | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
-+ { INFO("sst26wf016b", 0xbf2641, 0, 64 * 1024, 32, SECT_4K) },
- { INFO("sst26wf016", 0xbf2651, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_HAS_SST26LOCK) },
- { INFO("sst26wf032", 0xbf2622, 0, 64 * 1024, 64, SECT_4K | SPI_NOR_HAS_SST26LOCK) },
- { INFO("sst26wf064", 0xbf2643, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_HAS_SST26LOCK) },
-@@ -312,11 +334,19 @@ const struct flash_info spi_nor_ids[] =
- { INFO("w25q20ew", 0xef6012, 0, 64 * 1024, 4, SECT_4K) },
- { INFO("w25q32", 0xef4016, 0, 64 * 1024, 64, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- {
-+ INFO("w25q16dw", 0xef6015, 0, 64 * 1024, 32,
-+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ)
-+ },
-+ {
- INFO("w25q32dw", 0xef6016, 0, 64 * 1024, 64,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- {
-+ INFO("w25q16jv", 0xef7015, 0, 64 * 1024, 32,
-+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ)
-+ },
-+ {
- INFO("w25q32jv", 0xef7016, 0, 64 * 1024, 64,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
-@@ -363,6 +393,11 @@ const struct flash_info spi_nor_ids[] =
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- {
-+ INFO("w25q512jv", 0xef7119, 0, 64 * 1024, 512,
-+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
-+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
-+ },
-+ {
- INFO("w25q01jv", 0xef4021, 0, 64 * 1024, 2048,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
-@@ -370,6 +405,7 @@ const struct flash_info spi_nor_ids[] =
- { INFO("w25q80", 0xef5014, 0, 64 * 1024, 16, SECT_4K) },
- { INFO("w25q80bl", 0xef4014, 0, 64 * 1024, 16, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { INFO("w25q16cl", 0xef4015, 0, 64 * 1024, 32, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
-+ { INFO("w25q32bv", 0xef4016, 0, 64 * 1024, 64, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { INFO("w25q64cv", 0xef4017, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { INFO("w25q128", 0xef4018, 0, 64 * 1024, 256,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
-@@ -378,6 +414,7 @@ const struct flash_info spi_nor_ids[] =
- { INFO("w25q256", 0xef4019, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { INFO("w25m512jw", 0xef6119, 0, 64 * 1024, 1024, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- { INFO("w25m512jv", 0xef7119, 0, 64 * 1024, 1024, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
-+ { INFO("w25h02jv", 0xef9022, 0, 64 * 1024, 4096, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
- #endif
- #ifdef CONFIG_SPI_FLASH_XMC
- /* XMC (Wuhan Xinxin Semiconductor Manufacturing Corp.) */
+++ /dev/null
-From 4290ed7835e0a76792b8e554ae79e3f6d52ac800 Mon Sep 17 00:00:00 2001
-From: JaimeLiao <jaimeliao.tw@gmail.com>
-Date: Mon, 18 Jul 2022 14:49:22 +0800
-Subject: [PATCH] mtd: spi-nor-core: Add support for Macronix Octal flash
-
-Adding Macronix Octal flash for Octal DTR support.
-
-The octaflash series can be divided into the following types:
-
-MX25 series : Serial NOR Flash.
-MX66 series : Serial NOR Flash with stacked die.(Size larger than 1Gb)
-LM/UM series : Up to 250MHz clock frequency with both DTR/STR operation.
-LW/UW series : Support simultaneous Read-while-Write operation in multiple
- bank architecture. Read-while-write feature which means read
- data one bank while another bank is programing or erasing.
-
-MX25LM : 3.0V Octal I/O
- -https://www.mxic.com.tw/Lists/Datasheet/Attachments/7841/MX25LM51245G,%203V,%20512Mb,%20v1.1.pdf
-
-MX25UM : 1.8V Octal I/O
- -https://www.mxic.com.tw/Lists/Datasheet/Attachments/7525/MX25UM51245G%20Extreme%20Speed,%201.8V,%20512Mb,%20v1.0.pdf
-
-MX66LM : 3.0V Octal I/O with stacked die
- -https://www.mxic.com.tw/Lists/Datasheet/Attachments/7929/MX66LM1G45G,%203V,%201Gb,%20v1.1.pdf
-
-MX66UM : 1.8V Octal I/O with stacked die
- -https://www.mxic.com.tw/Lists/Datasheet/Attachments/7721/MX66UM1G45G,%201.8V,%201Gb,%20v1.1.pdf
-
-MX25LW : 3.0V Octal I/O with Read-while-Write
-MX25UW : 1.8V Octal I/O with Read-while-Write
-MX66LW : 3.0V Octal I/O with Read-while-Write and stack die
-MX66UW : 1.8V Octal I/O with Read-while-Write and stack die
-
-About LW/UW series, please contact us freely if you have any
-questions. For adding Octal NOR Flash IDs, we have validated
-each Flash on plateform zynq-picozed.
-
-As below are the SFDP table dump.
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c2943c
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx66uw2g345gx0
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx66uw2g345gx0
-zynq> hexdump mx66uw2g345gx0
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 ffff ffff ffff ffff
-0000040 20e5 ff8a ffff 7fff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 7987 0001 1284 e200 04cc 4667
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 237c 0048 0000 0000 8888
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
-0000130 4514 8098 0643 001f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c2853b
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx66lm1g45g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx66lm1g45g
-zynq> hexdump mx66lm1g45g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 ffff ffff ffff ffff
-0000040 20e5 ff8a ffff 3fff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 6987 0001 1282 e200 02cc 3867
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 a37c 0048 0000 0000 6666
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0000 0000
-0000130 3514 001c 0643 000f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c2853a
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx25lm51245g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25lm51245g
-zynq> hexdump mx25lm51245g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 ffff ffff ffff ffff
-0000040 20e5 ff8a ffff 1fff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 7989 0001 128d e200 02cc 4467
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 a37c 0048 0000 0000 6666
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0000 0000
-0000130 3514 001c 0643 000f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c2863a
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx25lw51245g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25lw51245g
-zynq> hexdump mx25lw51245g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 0000 0000 0000 0000
-0000040 20e5 ff8a ffff 1fff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 798b 0001 128f e200 04cc 4667
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 a37c 0048 0000 0000 6666
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0000 0000
-0000130 3514 001c 0643 000f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c28539
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx25lm25645g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25lm25645g
-zynq> hexdump mx25lm25645g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 ffff ffff ffff ffff
-0000040 20e5 ff8a ffff 0fff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 6987 0001 1282 d200 02cc 3867
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 a37c 0048 0000 0000 6666
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0000 0000
-0000130 3514 001c 0643 000f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c2843c
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx66uw2g345g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx66uw2g345g
-zynq> hexdump mx66uw2g345g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 ffff ffff ffff ffff
-0000040 20e5 ff8a ffff 7fff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 7987 0001 1284 e200 04cc 4667
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 237c 0048 0000 0000 8888
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
-0000130 4514 8098 0643 001f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c2803b
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx66um1g45g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx66um1g45g
-zynq> hexdump mx66um1g45g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 ffff ffff ffff ffff
-0000040 20e5 ff8a ffff 3fff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 7989 0001 128d e200 02cc 4467
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 a37c 0048 0000 0000 8888
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
-0000130 3514 809c 0643 000f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c2813b
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx66uw1g45g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx66uw1g45g
-zynq> hexdump mx66uw1g45g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 ffff ffff ffff ffff
-0000040 20e5 ff8a ffff 3fff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 798b 0001 128f e200 04cc 4667
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 a37c 0048 0000 0000 8888
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
-0000130 4514 8098 0643 000f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c2813a
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx25uw51245g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25uw51245g
-zynq> hexdump mx25uw51245g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 ffff ffff ffff ffff
-0000040 20e5 ff8a ffff 1fff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 798b 0001 128f e200 04cc 4667
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 a37c 0048 0000 0000 7777
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0000 0000
-0000130 4514 8098 0643 000f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c2843a
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx25uw51345g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25uw51345g
-zynq> hexdump mx25uw51345g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 ffff ffff ffff ffff
-0000040 20e5 ff8a ffff 1fff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 798b 0001 128f e200 04cc 4667
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 237c 0048 0000 0000 8888
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
-0000130 4514 8098 0643 000f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c28039
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx25um25645g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25um25645g
-zynq> random: fast init done
-zynq> hexdump mx25um25645g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 ffff ffff ffff ffff
-0000040 20e5 ff8a ffff 0fff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 7987 0001 1284 d200 02cc 3867
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 a37c 0048 0000 0000 8888
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
-0000130 3514 809c 0643 000f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c28139
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx25uw25645g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25uw25645g
-zynq> hexdump mx25uw25645g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 ffff ffff ffff ffff
-0000040 20e5 ff8a ffff 0fff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 7989 0001 128d d200 04cc 4667
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 a37c 0048 0000 0000 8888
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
-0000130 4514 8098 0643 000f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c28339
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx25um25345g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25um25345g
-zynq> hexdump mx25um25345g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 ffff ffff ffff ffff
-0000040 20e5 ff8a ffff 0fff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 6987 0001 1282 d200 02cc 3867
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 237c 0048 0000 0000 8888
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0904 0000
-0000130 4514 8098 0643 000f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c28439
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx25uw25345g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25uw25345g
-zynq> hexdump mx25uw25345g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 ffff ffff ffff ffff
-0000040 20e5 ff8a ffff 0fff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 7987 0001 1284 d200 04cc 4667
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 237c 0048 0000 0000 8888
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
-0000130 4514 8098 0643 000f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c28138
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx25uw12845g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25uw12845g
-zynq> hexdump mx25uw12845g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 0000 0000 0000 0000
-0000040 20e5 ff8a ffff 07ff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 798b 0001 128f c900 04cc 4667
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 a37c 0048 0000 0000 8888
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
-0000130 4514 8098 0643 000f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c28438
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx25uw12345g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25uw12345g
-zynq> hexdump mx25uw12345g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 ffff ffff ffff ffff
-0000040 20e5 ff8a ffff 07ff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 798b 0001 128f c900 04cc 4667
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 237c 0048 0000 0000 8888
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
-0000130 4514 8098 0643 000f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c28137
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx25uw6445g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25uw6445g
-zynq> hexdump mx25uw6445g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 ffff ffff ffff ffff
-0000040 20e5 ff8a ffff 03ff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 7989 0001 128d c400 04cc 4667
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 a37c 0048 0000 0000 8888
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
-0000130 4514 8098 0643 000f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
-c28437
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
-macronix
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
-mx25uw6345g
-zynq> cat /sys/bus/spi/devices/spi0.0/spi-nor/sfdp > mx25uw6345g
-zynq> hexdump mx25uw6345g
-0000000 4653 5044 0108 fd04 0700 1401 0040 ff00
-0000010 0187 1c01 0090 ff00 000a 0801 0100 ff00
-0000020 0005 0501 0120 ff00 0084 0201 0134 ff00
-0000030 0000 0000 0000 0000 ffff ffff ffff ffff
-0000040 20e5 ff8a ffff 03ff ff00 ff00 ff00 ff00
-0000050 ffee ffff ffff ff00 ffff ff00 200c d810
-0000060 ff00 ff00 798b 0001 128f c400 04cc 4667
-0000070 b030 b030 bdf4 5cd5 0000 ff00 1010 2000
-0000080 0000 0000 0000 237c 0048 0000 0000 8888
-0000090 0000 0000 0000 4000 d10f f3ff d10f f3ff
-00000a0 0500 9000 0500 b100 2b00 9500 2b00 9600
-00000b0 7172 b803 7172 b803 0000 0000 a390 8218
-00000c0 c000 9669 0000 0000 0000 0000 7172 9800
-00000d0 7172 b800 7172 9900 0000 0000 7172 9800
-00000e0 7172 f800 7172 9900 7172 f900 0000 0000
-00000f0 0000 0000 1501 d001 7172 d806 0000 5086
-0000100 0000 0106 0000 0000 0002 0301 0200 0000
-0000110 0000 0106 0000 0000 0000 0672 0200 0000
-0000120 ee00 69c0 7272 7171 d800 f6f7 0a00 0000
-0000130 4514 8098 0643 000f dc21 ffff ffff ffff
-0000140 ffff ffff ffff ffff ffff ffff ffff ffff
-
-Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com>
-Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
----
- drivers/mtd/spi/spi-nor-ids.c | 19 ++++++++++++++++++-
- 1 file changed, 18 insertions(+), 1 deletion(-)
-
---- a/drivers/mtd/spi/spi-nor-ids.c
-+++ b/drivers/mtd/spi/spi-nor-ids.c
-@@ -198,7 +198,24 @@ const struct flash_info spi_nor_ids[] =
- { INFO("mx66l2g45g", 0xc2201c, 0, 64 * 1024, 4096, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
- { INFO("mx25l1633e", 0xc22415, 0, 64 * 1024, 32, SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES | SECT_4K) },
- { INFO("mx25r6435f", 0xc22817, 0, 64 * 1024, 128, SECT_4K) },
-- { INFO("mx66uw2g345g", 0xc2943c, 0, 64 * 1024, 4096, SECT_4K | SPI_NOR_OCTAL_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx66uw2g345gx0", 0xc2943c, 0, 64 * 1024, 4096, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx66lm1g45g", 0xc2853b, 0, 64 * 1024, 2048, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx25lm51245g", 0xc2853a, 0, 64 * 1024, 1024, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx25lw51245g", 0xc2863a, 0, 64 * 1024, 1024, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx25lm25645g", 0xc28539, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx66uw2g345g", 0xc2843c, 0, 64 * 1024, 4096, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx66um1g45g", 0xc2803b, 0, 64 * 1024, 2048, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx66uw1g45g", 0xc2813b, 0, 64 * 1024, 2048, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx25uw51245g", 0xc2813a, 0, 64 * 1024, 1024, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx25uw51345g", 0xc2843a, 0, 64 * 1024, 1024, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx25um25645g", 0xc28039, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx25uw25645g", 0xc28139, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx25um25345g", 0xc28339, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx25uw25345g", 0xc28439, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx25uw12845g", 0xc28138, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx25uw12345g", 0xc28438, 0, 64 * 1024, 256, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx25uw6445g", 0xc28137, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
-+ { INFO("mx25uw6345g", 0xc28437, 0, 64 * 1024, 128, SECT_4K | SPI_NOR_OCTAL_DTR_READ | SPI_NOR_4B_OPCODES) },
- #endif
-
- #ifdef CONFIG_SPI_FLASH_STMICRO /* STMICRO */
+++ /dev/null
-From 47ed8b22fd561b65e8541919becc76ab3d86f7a3 Mon Sep 17 00:00:00 2001
-From: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
-Date: Fri, 8 Jul 2022 12:03:19 -0700
-Subject: [PATCH] mtd: spi-nor-ids: add winbond w25q512nw family support
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Add Winbond w25q512nwq/n and w25q512nwm support.
-
-datasheet:
-https://www.winbond.com/resource-files/W25Q512NW%20RevB%2007192021.pdf
-
-Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
-Reviewed-by: Cédric Le Goater <clg@kaod.org>
-Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
----
- drivers/mtd/spi/spi-nor-ids.c | 10 ++++++++++
- 1 file changed, 10 insertions(+)
-
---- a/drivers/mtd/spi/spi-nor-ids.c
-+++ b/drivers/mtd/spi/spi-nor-ids.c
-@@ -415,6 +415,16 @@ const struct flash_info spi_nor_ids[] =
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
- },
- {
-+ INFO("w25q512nwq", 0xef6020, 0, 64 * 1024, 1024,
-+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
-+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
-+ },
-+ {
-+ INFO("w25q512nwm", 0xef8020, 0, 64 * 1024, 1024,
-+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
-+ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
-+ },
-+ {
- INFO("w25q01jv", 0xef4021, 0, 64 * 1024, 2048,
- SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
- SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+++ /dev/null
-From 22832a0a15227e3fcc364b356247d8aeb9ce45b3 Mon Sep 17 00:00:00 2001
-From: Daniel Golle <daniel@makrotopia.org>
-Date: Sat, 27 Aug 2022 04:05:31 +0100
-Subject: [PATCH 1/2] bootm: fix typo imape_comp -> image_comp
-
-Chage variable name 'imape_comp' to the supposedly intended name
-'image_comp'.
-
-Signed-off-by: Daniel Golle <daniel@makrotopia.org>
----
- boot/bootm.c | 8 ++++----
- 1 file changed, 4 insertions(+), 4 deletions(-)
-
---- a/boot/bootm.c
-+++ b/boot/bootm.c
-@@ -1006,7 +1006,7 @@ static int bootm_host_load_image(const v
- int noffset;
- ulong load_end;
- uint8_t image_type;
-- uint8_t imape_comp;
-+ uint8_t image_comp;
- void *load_buf;
- int ret;
-
-@@ -1024,20 +1024,20 @@ static int bootm_host_load_image(const v
- return -EINVAL;
- }
-
-- if (fit_image_get_comp(fit, noffset, &imape_comp)) {
-+ if (fit_image_get_comp(fit, noffset, &image_comp)) {
- puts("Can't get image compression!\n");
- return -EINVAL;
- }
-
- /* Allow the image to expand by a factor of 4, should be safe */
- load_buf = malloc((1 << 20) + len * 4);
-- ret = image_decomp(imape_comp, 0, data, image_type, load_buf,
-+ ret = image_decomp(image_comp, 0, data, image_type, load_buf,
- (void *)data, len, CONFIG_SYS_BOOTM_LEN,
- &load_end);
- free(load_buf);
-
- if (ret) {
-- ret = handle_decomp_error(imape_comp, load_end - 0, ret);
-+ ret = handle_decomp_error(image_comp, load_end - 0, ret);
- if (ret != BOOTM_ERR_UNIMPLEMENTED)
- return ret;
- }
+++ /dev/null
-From b2c109c012ca946baebbb23e7f4301f6eee4c6f3 Mon Sep 17 00:00:00 2001
-From: Daniel Golle <daniel@makrotopia.org>
-Date: Mon, 15 Aug 2022 12:15:50 +0200
-Subject: [PATCH 2/2] image-fit: don't set compression if it can't be read
-
-fit_image_get_comp() should not set value -1 in case it can't read
-the compression node. Instead, leave the value untouched in that case
-as it can be absent and a default value previously defined by the
-caller of fit_image_get_comp() should be used.
-
-As a result the warning message
-WARNING: 'compression' nodes for ramdisks are deprecated, please fix your .its file!
-no longer shows if the compression node is actually absent.
-
-Signed-off-by: Daniel Golle <daniel@makrotopia.org>
----
- boot/bootm.c | 6 ++----
- boot/image-fit.c | 3 +--
- cmd/ximg.c | 7 ++-----
- 3 files changed, 5 insertions(+), 11 deletions(-)
-
---- a/boot/bootm.c
-+++ b/boot/bootm.c
-@@ -1024,10 +1024,8 @@ static int bootm_host_load_image(const v
- return -EINVAL;
- }
-
-- if (fit_image_get_comp(fit, noffset, &image_comp)) {
-- puts("Can't get image compression!\n");
-- return -EINVAL;
-- }
-+ if (fit_image_get_comp(fit, noffset, &image_comp))
-+ image_comp = IH_COMP_NONE;
-
- /* Allow the image to expand by a factor of 4, should be safe */
- load_buf = malloc((1 << 20) + len * 4);
---- a/boot/image-fit.c
-+++ b/boot/image-fit.c
-@@ -477,7 +477,7 @@ void fit_print_contents(const void *fit)
- void fit_image_print(const void *fit, int image_noffset, const char *p)
- {
- char *desc;
-- uint8_t type, arch, os, comp;
-+ uint8_t type, arch, os, comp = IH_COMP_NONE;
- size_t size;
- ulong load, entry;
- const void *data;
-@@ -794,7 +794,6 @@ int fit_image_get_comp(const void *fit,
- data = fdt_getprop(fit, noffset, FIT_COMP_PROP, &len);
- if (data == NULL) {
- fit_get_debug(fit, noffset, FIT_COMP_PROP, len);
-- *comp = -1;
- return -1;
- }
-
---- a/cmd/ximg.c
-+++ b/cmd/ximg.c
-@@ -171,11 +171,8 @@ do_imgextract(struct cmd_tbl *cmdtp, int
- return 1;
- }
-
-- if (fit_image_get_comp(fit_hdr, noffset, &comp)) {
-- puts("Could not find script subimage "
-- "compression type\n");
-- return 1;
-- }
-+ if (fit_image_get_comp(fit_hdr, noffset, &comp))
-+ comp = IH_COMP_NONE;
-
- data = (ulong)fit_data;
- len = (ulong)fit_len;
--- a/include/configs/mt7622.h
+++ b/include/configs/mt7622.h
-@@ -30,6 +30,7 @@
+@@ -23,6 +23,7 @@
/* Ethernet */
#define CONFIG_IPADDR 192.168.1.1
#endif
--- a/include/configs/mt7623.h
+++ b/include/configs/mt7623.h
-@@ -45,6 +45,7 @@
+@@ -37,6 +37,7 @@
/* Ethernet */
#define CONFIG_IPADDR 192.168.1.1
#define CONFIG_SERVERIP 192.168.1.2
--- a/include/configs/mt7629.h
+++ b/include/configs/mt7629.h
-@@ -45,5 +45,6 @@
+@@ -32,5 +32,6 @@
/* Ethernet */
#define CONFIG_IPADDR 192.168.1.1
#define CONFIG_SERVERIP 192.168.1.2
--- a/drivers/mtd/Kconfig
+++ b/drivers/mtd/Kconfig
-@@ -158,6 +158,8 @@ config SYS_MAX_FLASH_BANKS_DETECT
+@@ -210,6 +210,8 @@ config SYS_MAX_FLASH_BANKS_DETECT
to reduce the effective number of flash bank, between 0 and
CONFIG_SYS_MAX_FLASH_BANKS
config SYS_NAND_MAX_CHIPS
--- a/drivers/mtd/Makefile
+++ b/drivers/mtd/Makefile
-@@ -39,3 +39,5 @@ obj-$(CONFIG_$(SPL_TPL_)SPI_FLASH_SUPPOR
+@@ -38,3 +38,5 @@ obj-$(CONFIG_$(SPL_TPL_)SPI_FLASH_SUPPOR
obj-$(CONFIG_SPL_UBI) += ubispl/
endif
--- a/env/Kconfig
+++ b/env/Kconfig
-@@ -37,7 +37,7 @@ config ENV_IS_NOWHERE
+@@ -53,7 +53,7 @@ config ENV_IS_NOWHERE
!ENV_IS_IN_MMC && !ENV_IS_IN_NAND && \
!ENV_IS_IN_NVRAM && !ENV_IS_IN_ONENAND && \
!ENV_IS_IN_REMOTE && !ENV_IS_IN_SPI_FLASH && \
help
Define this if you don't want to or can't have an environment stored
on a storage medium. In this case the environment will still exist
-@@ -226,6 +226,27 @@ config ENV_IS_IN_MMC
+@@ -242,6 +242,27 @@ config ENV_IS_IN_MMC
This value is also in units of bytes, but must also be aligned to
an MMC sector boundary.
config ENV_IS_IN_NAND
bool "Environment in a NAND device"
depends on !CHAIN_OF_TRUST
-@@ -531,10 +552,16 @@ config ENV_ADDR_REDUND
+@@ -549,10 +570,16 @@ config ENV_ADDR_REDUND
Offset from the start of the device (or partition) of the redundant
environment location.
default 0x3f8000 if ARCH_ROCKCHIP && ENV_IS_IN_MMC
default 0x140000 if ARCH_ROCKCHIP && ENV_IS_IN_SPI_FLASH
default 0xF0000 if ARCH_SUNXI
-@@ -581,6 +608,12 @@ config ENV_SECT_SIZE
+@@ -599,6 +626,12 @@ config ENV_SECT_SIZE
help
Size of the sector containing the environment.
--- a/drivers/mtd/Kconfig
+++ b/drivers/mtd/Kconfig
-@@ -174,4 +174,6 @@ source "drivers/mtd/spi/Kconfig"
+@@ -226,4 +226,6 @@ source "drivers/mtd/spi/Kconfig"
source "drivers/mtd/ubi/Kconfig"
endmenu
--- a/drivers/mtd/Makefile
+++ b/drivers/mtd/Makefile
-@@ -41,3 +41,4 @@ obj-$(CONFIG_SPL_UBI) += ubispl/
+@@ -40,3 +40,4 @@ obj-$(CONFIG_SPL_UBI) += ubispl/
endif
obj-$(CONFIG_MTK_SPI_NAND) += mtk-snand/
--- a/common/board_r.c
+++ b/common/board_r.c
-@@ -382,6 +382,20 @@ static int initr_nand(void)
+@@ -385,6 +385,20 @@ static int initr_nand(void)
}
#endif
#if defined(CONFIG_CMD_ONENAND)
/* go init the NAND */
static int initr_onenand(void)
-@@ -703,6 +717,9 @@ static init_fnc_t init_sequence_r[] = {
+@@ -697,6 +711,9 @@ static init_fnc_t init_sequence_r[] = {
#ifdef CONFIG_CMD_ONENAND
initr_onenand,
#endif
--- a/cmd/Kconfig
+++ b/cmd/Kconfig
-@@ -1260,6 +1260,12 @@ config CMD_NAND_TORTURE
+@@ -1305,6 +1305,12 @@ config CMD_NAND_TORTURE
endif # CMD_NAND
/*
--- a/env/Kconfig
+++ b/env/Kconfig
-@@ -37,7 +37,7 @@ config ENV_IS_NOWHERE
+@@ -53,7 +53,7 @@ config ENV_IS_NOWHERE
!ENV_IS_IN_MMC && !ENV_IS_IN_NAND && \
!ENV_IS_IN_NVRAM && !ENV_IS_IN_ONENAND && \
!ENV_IS_IN_REMOTE && !ENV_IS_IN_SPI_FLASH && \
help
Define this if you don't want to or can't have an environment stored
on a storage medium. In this case the environment will still exist
-@@ -285,6 +285,21 @@ config ENV_IS_IN_NAND
- Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
- using CONFIG_ENV_OFFSET_OOB.
+@@ -303,6 +303,21 @@ config ENV_RANGE
+ Specifying a range with more erase blocks than are needed to hold
+ CONFIG_ENV_SIZE allows bad blocks within the range to be avoided.
+config ENV_IS_IN_NMBM
+ bool "Environment in a NMBM upper MTD layer"
config ENV_IS_IN_NVRAM
bool "Environment in a non-volatile RAM"
depends on !CHAIN_OF_TRUST
-@@ -561,7 +576,7 @@ config ENV_MTD_NAME
+@@ -579,7 +594,7 @@ config ENV_MTD_NAME
config ENV_OFFSET
hex "Environment offset"
depends on ENV_IS_IN_EEPROM || ENV_IS_IN_MMC || ENV_IS_IN_NAND || \
--- a/cmd/Kconfig
+++ b/cmd/Kconfig
-@@ -1260,6 +1260,14 @@ config CMD_NAND_TORTURE
+@@ -1305,6 +1305,14 @@ config CMD_NAND_TORTURE
endif # CMD_NAND
--- a/drivers/mtd/spi/spi-nor-core.c
+++ b/drivers/mtd/spi/spi-nor-core.c
-@@ -2742,6 +2742,100 @@ static int spi_nor_init_params(struct sp
+@@ -2791,6 +2791,100 @@ static int spi_nor_init_params(struct sp
return 0;
}
static int spi_nor_hwcaps2cmd(u32 hwcaps, const int table[][2], size_t size)
{
size_t i;
-@@ -3719,6 +3813,7 @@ int spi_nor_scan(struct spi_nor *nor)
+@@ -3858,6 +3952,7 @@ int spi_nor_scan(struct spi_nor *nor)
nor->write = spi_nor_write_data;
nor->read_reg = spi_nor_read_reg;
nor->write_reg = spi_nor_write_reg;
#define SNOR_MFR_CYPRESS 0x34
/*
-@@ -547,6 +548,7 @@ struct spi_nor {
+@@ -558,6 +559,7 @@ struct spi_nor {
void (*unprepare)(struct spi_nor *nor, enum spi_nor_ops ops);
int (*read_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len);
int (*write_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len);
--- a/cmd/sf.c
+++ b/cmd/sf.c
-@@ -391,6 +391,14 @@ static int do_spi_protect(int argc, char
+@@ -403,6 +403,14 @@ static int do_spi_protect(int argc, char
return ret == 0 ? 0 : 1;
}
enum {
STAGE_ERASE,
STAGE_CHECK,
-@@ -587,6 +595,8 @@ static int do_spi_flash(struct cmd_tbl *
+@@ -599,6 +607,8 @@ static int do_spi_flash(struct cmd_tbl *
ret = do_spi_flash_erase(argc, argv);
else if (strcmp(cmd, "protect") == 0)
ret = do_spi_protect(argc, argv);
else if (IS_ENABLED(CONFIG_CMD_SF_TEST) && !strcmp(cmd, "test"))
ret = do_spi_flash_test(argc, argv);
else
-@@ -617,7 +627,8 @@ static const char long_help[] =
+@@ -629,7 +639,8 @@ static const char long_help[] =
" at `addr' to flash at `offset'\n"
" or to start of mtd `partition'\n"
"sf protect lock/unlock sector len - protect/unprotect 'len' bytes starting\n"
reg = <0x11014000 0x1000>;
--- a/configs/mt7622_rfb_defconfig
+++ b/configs/mt7622_rfb_defconfig
-@@ -18,6 +18,7 @@ CONFIG_LOG=y
- CONFIG_SYS_PROMPT="MT7622> "
+@@ -20,6 +20,7 @@ CONFIG_SYS_MAXARGS=8
+ CONFIG_SYS_PBSIZE=1049
CONFIG_CMD_BOOTMENU=y
CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
CONFIG_CMD_PCI=y
CONFIG_CMD_SF_TEST=y
CONFIG_CMD_PING=y
-@@ -33,6 +34,10 @@ CONFIG_SYSCON=y
+@@ -35,6 +36,10 @@ CONFIG_SYSCON=y
CONFIG_CLK=y
CONFIG_MMC_HS200_SUPPORT=y
CONFIG_MMC_MTK=y
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
-@@ -1206,6 +1206,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
+@@ -1234,6 +1234,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
mt7623n-bananapi-bpi-r2.dtb \
mt7629-rfb.dtb \
mt7981-rfb.dtb \
--- a/drivers/mtd/spi/spi-nor-core.c
+++ b/drivers/mtd/spi/spi-nor-core.c
-@@ -641,6 +641,7 @@ static int set_4byte(struct spi_nor *nor
+@@ -648,6 +648,7 @@ static int set_4byte(struct spi_nor *nor
case SNOR_MFR_ISSI:
case SNOR_MFR_MACRONIX:
case SNOR_MFR_WINBOND:
--- a/drivers/mmc/Kconfig
+++ b/drivers/mmc/Kconfig
-@@ -789,6 +789,14 @@ config MMC_MTK
+@@ -812,6 +812,14 @@ config MMC_MTK
This is needed if support for any SD/SDIO/MMC devices is required.
If unsure, say N.
--- a/env/Kconfig
+++ b/env/Kconfig
-@@ -647,6 +647,12 @@ config ENV_UBI_VOLUME_REDUND
+@@ -665,6 +665,12 @@ config ENV_UBI_VOLUME_REDUND
help
Name of the redundant volume that you want to store the environment in.
+++ /dev/null
---- a/include/configs/mt7986.h
-+++ b/include/configs/mt7986.h
-@@ -11,6 +11,11 @@
-
- #include <linux/sizes.h>
-
-+#define CONFIG_SYS_MAXARGS 32
-+#define CONFIG_SYS_BOOTM_LEN SZ_128M
-+#define CONFIG_SYS_CBSIZE SZ_1K
-+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
-+ sizeof(CONFIG_SYS_PROMPT) + 16)
- #define CONFIG_SYS_NONCACHED_MEMORY SZ_1M
- #define CONFIG_SYS_MMC_ENV_DEV 0
-
-@@ -19,6 +24,11 @@
-
- /* SPL -> Uboot */
- #define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
-+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE + SZ_2M - \
-+ GENERATED_GBL_DATA_SIZE)
-+
-+/* Flash */
-+#define CONFIG_SYS_NAND_MAX_CHIPS 1
-
- /* DRAM */
- #define CONFIG_SYS_SDRAM_BASE 0x40000000
--- a/Makefile
+++ b/Makefile
-@@ -1061,7 +1061,7 @@ quiet_cmd_pad_cat = CAT $@
+@@ -1062,7 +1062,7 @@ quiet_cmd_pad_cat = CAT $@
cmd_pad_cat = $(cmd_objcopy) && $(append) || { rm -f $@; false; }
quiet_cmd_lzma = LZMA $@
--- a/cmd/bootm.c
+++ b/cmd/bootm.c
-@@ -257,6 +257,67 @@ U_BOOT_CMD(
+@@ -256,6 +256,67 @@ U_BOOT_CMD(
/* iminfo - print header info for a requested image */
/*******************************************************************/
#if defined(CONFIG_CMD_IMI)
{
--- a/boot/image-fit.c
+++ b/boot/image-fit.c
-@@ -1994,6 +1994,51 @@ static const char *fit_get_image_type_pr
+@@ -2031,6 +2031,51 @@ static const char *fit_get_image_type_pr
return "unknown";
}
--- a/cmd/Kconfig
+++ b/cmd/Kconfig
-@@ -540,6 +540,12 @@ config CMD_ENV_EXISTS
+@@ -579,6 +579,12 @@ config CMD_ENV_EXISTS
Check if a variable is defined in the environment for use in
shell scripting.
--- a/boot/image-fdt.c
+++ b/boot/image-fdt.c
-@@ -639,6 +639,12 @@ int image_setup_libfdt(bootm_headers_t *
+@@ -636,6 +636,12 @@ int image_setup_libfdt(bootm_headers_t *
images->fit_uname_cfg,
strlen(images->fit_uname_cfg) + 1, 1);
--- a/Makefile
+++ b/Makefile
-@@ -2063,26 +2063,7 @@ endif
+@@ -2032,26 +2032,7 @@ endif
# Check dtc and pylibfdt, if DTC is provided, else build them
PHONY += scripts_dtc
scripts_dtc: scripts_basic
--- a/configs/mt7623n_bpir2_defconfig
+++ b/configs/mt7623n_bpir2_defconfig
-@@ -4,53 +4,138 @@ CONFIG_ARCH_MEDIATEK=y
+@@ -4,57 +4,142 @@ CONFIG_ARCH_MEDIATEK=y
CONFIG_SYS_TEXT_BASE=0x81e00000
CONFIG_SYS_MALLOC_F_LEN=0x4000
CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x10000
CONFIG_ENV_OFFSET=0x100000
CONFIG_DEFAULT_DEVICE_TREE="mt7623n-bananapi-bpi-r2"
+-CONFIG_SYS_PROMPT="U-Boot> "
+CONFIG_USE_DEFAULT_ENV_FILE=y
++CONFIG_SYS_PROMPT="MT7623> "
CONFIG_TARGET_MT7623=y
CONFIG_SYS_LOAD_ADDR=0x84000000
CONFIG_DISTRO_DEFAULTS=y
+ CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+ CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x81ffff10
CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
+CONFIG_FIT_ENABLE_SHA256_SUPPORT=y
+CONFIG_CFB_CONSOLE_ANSI=y
+CONFIG_CMD_ENV_FLAGS=y
# CONFIG_DISPLAY_BOARDINFO is not set
--CONFIG_SYS_PROMPT="U-Boot> "
-+CONFIG_SYS_PROMPT="MT7623> "
+ CONFIG_SYS_MAXARGS=8
+ CONFIG_SYS_PBSIZE=1049
+ CONFIG_SYS_BOOTM_LEN=0x4000000
CONFIG_CMD_BOOTMENU=y
+CONFIG_CMD_BOOTP=y
+CONFIG_CMD_BUTTON=y
CONFIG_SUPPORT_EMMC_BOOT=y
CONFIG_MMC_HS400_SUPPORT=y
CONFIG_MMC_MTK=y
-+CONFIG_MTK_AHCI=y
+CONFIG_MTK_POWER_DOMAIN=y
+CONFIG_MTK_SERIAL=y
+CONFIG_MTK_TIMER=y
+CONFIG_PCIE_MEDIATEK=y
+CONFIG_PHY=y
CONFIG_PHY_FIXED=y
--CONFIG_DM_ETH=y
-CONFIG_MEDIATEK_ETH=y
CONFIG_PINCTRL=y
CONFIG_PINCONF=y
--- a/configs/mt7623a_unielec_u7623_02_defconfig
+++ b/configs/mt7623a_unielec_u7623_02_defconfig
-@@ -4,51 +4,135 @@ CONFIG_ARCH_MEDIATEK=y
+@@ -4,55 +4,140 @@ CONFIG_ARCH_MEDIATEK=y
CONFIG_SYS_TEXT_BASE=0x81e00000
CONFIG_SYS_MALLOC_F_LEN=0x4000
CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x10000
CONFIG_ENV_OFFSET=0x100000
CONFIG_DEFAULT_DEVICE_TREE="mt7623a-unielec-u7623-02-emmc"
+-CONFIG_SYS_PROMPT="U-Boot> "
+CONFIG_USE_DEFAULT_ENV_FILE=y
++CONFIG_SYS_PROMPT="MT7623> "
CONFIG_TARGET_MT7623=y
CONFIG_SYS_LOAD_ADDR=0x84000000
CONFIG_DISTRO_DEFAULTS=y
+ CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+ CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x81ffff10
CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
+CONFIG_FIT_ENABLE_SHA256_SUPPORT=y
+CONFIG_CFB_CONSOLE_ANSI=y
+CONFIG_CMD_ENV_FLAGS=y
# CONFIG_DISPLAY_BOARDINFO is not set
--CONFIG_SYS_PROMPT="U-Boot> "
-+CONFIG_SYS_PROMPT="MT7623> "
+ CONFIG_SYS_MAXARGS=8
+ CONFIG_SYS_PBSIZE=1049
+ CONFIG_SYS_BOOTM_LEN=0x4000000
CONFIG_CMD_BOOTMENU=y
+CONFIG_CMD_BOOTP=y
+CONFIG_CMD_BOOTZ=y
+CONFIG_PCIE_MEDIATEK=y
+CONFIG_PHY=y
CONFIG_PHY_FIXED=y
--CONFIG_DM_ETH=y
-CONFIG_MEDIATEK_ETH=y
CONFIG_PINCTRL=y
CONFIG_PINCONF=y
+};
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
-@@ -1203,6 +1203,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
+@@ -1231,6 +1231,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
mt7622-rfb.dtb \
mt7623a-unielec-u7623-02-emmc.dtb \
mt7622-bananapi-bpi-r64.dtb \
+};
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
-@@ -1204,6 +1204,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
+@@ -1232,6 +1232,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
mt7623a-unielec-u7623-02-emmc.dtb \
mt7622-bananapi-bpi-r64.dtb \
mt7622-linksys-e8450-ubi.dtb \
+_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title \e[33m$ver\e[0m"
--- a/common/board_r.c
+++ b/common/board_r.c
-@@ -62,6 +62,7 @@
+@@ -65,6 +65,7 @@
#include <asm-generic/gpio.h>
#include <efi_loader.h>
#include <relocate.h>
DECLARE_GLOBAL_DATA_PTR;
-@@ -406,6 +407,20 @@ static int initr_onenand(void)
+@@ -409,6 +410,20 @@ static int initr_onenand(void)
}
#endif
#ifdef CONFIG_MMC
static int initr_mmc(void)
{
-@@ -720,6 +735,9 @@ static init_fnc_t init_sequence_r[] = {
+@@ -714,6 +729,9 @@ static init_fnc_t init_sequence_r[] = {
#ifdef CONFIG_NMBM_MTD
initr_nmbm,
#endif
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
-@@ -1211,6 +1211,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
+@@ -1239,6 +1239,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
mt7981-snfi-nand-rfb.dtb \
mt7981-emmc-rfb.dtb \
mt7981-sd-rfb.dtb \
+CONFIG_CMD_SF=y
+CONFIG_CMD_NAND=y
+CONFIG_CMD_NAND_TRIMFFS=y
-+# CONFIG_ENABLE_NAND_NMBM is not set
--- /dev/null
+++ b/configs/mt7986a_bpi-r3-nor_defconfig
@@ -0,0 +1,193 @@
+CONFIG_CMD_SF=y
+#CONFIG_CMD_NAND=y
+#CONFIG_CMD_NAND_TRIMFFS=y
-+# CONFIG_ENABLE_NAND_NMBM is not set
--- /dev/null
+++ b/configs/mt7986a_bpi-r3-sd_defconfig
@@ -0,0 +1,192 @@
+CONFIG_CMD_SF=y
+CONFIG_CMD_NAND=y
+CONFIG_CMD_NAND_TRIMFFS=y
-+# CONFIG_ENABLE_NAND_NMBM is not set
--- /dev/null
+++ b/configs/mt7986a_bpi-r3-snand_defconfig
@@ -0,0 +1,193 @@
+#CONFIG_CMD_SF=y
+CONFIG_CMD_NAND=y
+CONFIG_CMD_NAND_TRIMFFS=y
-+# CONFIG_ENABLE_NAND_NMBM is not set
--- /dev/null
+++ b/arch/arm/dts/mt7986a-bpi-r3-emmc.dts
@@ -0,0 +1,33 @@
projects / openwrt / openwrt.git / commitdiff