ramips: add new device ZyXEL Keenetic as kn
authorAlexey Belyaev <spider@spider.vc>
Thu, 27 Apr 2017 18:02:05 +0000 (00:02 +0600)
committerMathias Kresin <dev@kresin.me>
Wed, 10 May 2017 06:45:12 +0000 (08:45 +0200)
This device exactly same as NBG-419N but with USB port and USB Led.

Specification:

- SoC: Ralink RT3052 (MIPS24Kc) @384MHz
- RAM: 32 MiB
- Flash: 8 MiB
- WLAN: WiSoC 2T2R/300Mbps (2.4GHz)
- LAN: 4x100M
- WAN: 1x100M
- USB: 1x2.0

Installation via serial console (57600 8N1) from TFTP server
 - rename the firmware to something shorter, for example
   "sysupgrade.bin" (max. 32 chars)
 - copy firmware TFTP server's directory
 - when you power on device, and see U-Boot log, immediatly push "2"
   once.
 - You will see this message:
     2: System Load Linux Kernel then write to Flash via TFTP.
        Warning!! Erase Linux in Flash then burn new one. Are you sure?
 - Push "y", and enter: device IP, then TFTP server's IP, and then
   image firmware file name.

The firmware will be downloaded within ~30 seconds and flashed to the
device (It will take about 2 minutes).

Signed-off-by: Alexey Belyaev <spider@spider.vc>
[squash commits, compact commit message, fix compatible string, remove
superfluous pinmuxes]
Signed-off-by: Mathias Kresin <dev@kresin.me>
target/linux/ramips/base-files/etc/board.d/01_leds
target/linux/ramips/base-files/etc/board.d/02_network
target/linux/ramips/base-files/etc/diag.sh
target/linux/ramips/base-files/lib/ramips.sh
target/linux/ramips/base-files/lib/upgrade/platform.sh
target/linux/ramips/dts/kn.dts [new file with mode: 0644]
target/linux/ramips/image/rt305x.mk

index 52542ec..9322228 100755 (executable)
@@ -222,6 +222,11 @@ ht-tm02)
        ucidef_set_led_netdev "eth" "Ethernet" "$board:green:lan" "eth0"
        set_wifi_led "$board:blue:wlan"
        ;;
+kn|\
+nbg-419n2)
+       set_usb_led "$board:green:usb"
+       set_wifi_led "rt2800pci-phy0::radio"
+       ;;
 kn_rc|\
 kn_rf|\
 kng_rc)
@@ -265,10 +270,6 @@ mzk-ex750np)
 na930)
        set_usb_led "$board:blue:status"
        ;;
-nbg-419n2)
-       set_usb_led "$board:green:usb"
-       set_wifi_led "rt2800pci-phy0::radio"
-       ;;
 newifi-d1)
        set_usb_led "$board:red:status"
        ;;
index 80a3bc2..cefc4f4 100755 (executable)
@@ -84,6 +84,7 @@ ramips_setup_interfaces()
        hc5661a|\
        hc5962|\
        hlk-rm04|\
+       kn|\
        kn_rc|\
        mac1200rv2|\
        miwifi-mini|\
index 461f46c..a36ce54 100644 (file)
@@ -24,6 +24,7 @@ get_status_led() {
        e1700|\
        ex3700|\
        fonera20n|\
+       kn|\
        kn_rc|\
        kn_rf|\
        kng_rc|\
index 87cb7ff..506a982 100755 (executable)
@@ -670,6 +670,9 @@ ramips_board_detect() {
        *"ZBT-WR8305RT")
                name="zbt-wr8305rt"
                ;;
+       *"ZyXEL Keenetic")
+               name="kn"
+               ;;
        *"ZyXEL Keenetic Omni")
                name="kn_rc"
                ;;
index adad8da..0390093 100755 (executable)
@@ -76,6 +76,7 @@ platform_check_image() {
        jhr-n805r|\
        jhr-n825r|\
        jhr-n926r|\
+       kn|\
        kn_rc|\
        kn_rf|\
        kng_rc|\
diff --git a/target/linux/ramips/dts/kn.dts b/target/linux/ramips/dts/kn.dts
new file mode 100644 (file)
index 0000000..77b047c
--- /dev/null
@@ -0,0 +1,113 @@
+/dts-v1/;
+
+#include "rt3050.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       compatible = "zyxel,keenetic", "ralink,rt3052-soc";
+       model = "ZyXEL Keenetic";
+
+       cfi@1f000000 {
+               compatible = "cfi-flash";
+               reg = <0x1f000000 0x800000>;
+               bank-width = <2>;
+               device-width = <2>;
+               #address-cells = <1>;
+               #size-cells = <1>;
+
+               partition@0 {
+                       label = "u-boot";
+                       reg = <0x0 0x30000>;
+                       read-only;
+               };
+
+               partition@30000 {
+                       label = "u-boot-env";
+                       reg = <0x30000 0x10000>;
+                       read-only;
+               };
+
+               factory: partition@40000 {
+                       label = "factory";
+                       reg = <0x40000 0x10000>;
+                       read-only;
+               };
+
+               partition@50000 {
+                       label = "firmware";
+                       reg = <0x50000 0x3b0000>;
+               };
+       };
+
+       gpio-leds {
+               compatible = "gpio-leds";
+
+               power {
+                       label = "kn:green:power";
+                       gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
+               };
+
+               usb {
+                       label = "kn:green:usb";
+                       gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+               };
+
+               wps {
+                       label = "kn:green:wps";
+                       gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       gpio-keys-polled {
+               compatible = "gpio-keys-polled";
+               #address-cells = <1>;
+               #size-cells = <0>;
+               poll-interval = <20>;
+
+               reset {
+                       label = "reset";
+                       gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+               };
+
+               rfkill {
+                       label = "rfkill";
+                       gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+                       linux,code = <KEY_RFKILL>;
+                       linux,input-type = <EV_SW>;
+               };
+
+               wps {
+                       label = "wps";
+                       gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
+               };
+       };
+};
+
+&pinctrl {
+       state_default: pinctrl0 {
+               gpio {
+                       ralink,group = "uartf";
+                       ralink,function = "gpio";
+               };
+       };
+};
+
+&ethernet {
+       mtd-mac-address = <&factory 0x28>;
+};
+
+&esw {
+       mediatek,portmap = <0x2f>;
+};
+
+&wmac {
+       ralink,mtd-eeprom = <&factory 0>;
+};
+
+&otg {
+       status = "okay";
+};
index 69533ce..62ced9b 100644 (file)
@@ -850,3 +850,12 @@ define Device/xdxrn502j
   DEVICE_TITLE := XDX RN502J
 endef
 TARGET_DEVICES += xdxrn502j
+
+define Device/kn
+  DTS := kn
+  BLOCKSIZE := 64k
+  IMAGE_SIZE := $(ralink_default_fw_size_4M)
+  DEVICE_TITLE := ZyXEL Keenetic
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ehci kmod-usb-ledtrig-usbport
+endef
+TARGET_DEVICES += kn