ar71xx: add support for YunCore SR3200 and XD3200
authorPiotr Dymacz <pepe2k@gmail.com>
Fri, 2 Dec 2016 21:42:41 +0000 (22:42 +0100)
committerJohn Crispin <john@phrozen.org>
Mon, 12 Dec 2016 08:57:40 +0000 (09:57 +0100)
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.

YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.

Common specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm

SR3200 specification:

- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB

XD3200 specification:

- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB

LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.

Flash instruction under vendor firmware, using telnet/SSH:

1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
12 files changed:
target/linux/ar71xx/base-files/etc/board.d/01_leds
target/linux/ar71xx/base-files/etc/board.d/02_network
target/linux/ar71xx/base-files/etc/diag.sh
target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
target/linux/ar71xx/base-files/lib/ar71xx.sh
target/linux/ar71xx/base-files/lib/upgrade/platform.sh
target/linux/ar71xx/config-4.4
target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
target/linux/ar71xx/files/arch/mips/ath79/Makefile
target/linux/ar71xx/files/arch/mips/ath79/mach-sr3200.c [new file with mode: 0644]
target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
target/linux/ar71xx/image/generic.mk

index a93ea1d..38e665f 100755 (executable)
@@ -444,6 +444,9 @@ som9331)
        ucidef_set_led_wlan "wlan" "WLAN" "$board:red:wlan" "phy0tpt"
        ucidef_set_led_usbdev "usb" "USB" "$board:green:system" "1-1"
        ;;
+sr3200)
+       ucidef_set_led_wlan "wlan2g" "WLAN2G" "$board:green:wlan2g" "phy1tpt"
+       ;;
 tellstick-znet-lite)
        ucidef_set_led_netdev "lan_act" "LANACT" "tellstick:green:lan" "eth0" "tx rx"
        ucidef_set_led_netdev "lan_link" "LANLINK" "tellstick:orange:lan" "eth0" "link"
@@ -738,6 +741,9 @@ wzr-hp-g300nh)
        ucidef_set_led_netdev "router" "Router" "buffalo:green:router" "eth1"
        ucidef_set_led_usbdev "usb" "USB" "buffalo:blue:usb" "1-1"
        ;;
+xd3200)
+       ucidef_set_led_wlan "wlan2g" "WLAN2G" "$board:blue:wlan2g" "phy1tpt"
+       ;;
 z1)
        ucidef_set_led_netdev "wlan1" "WLAN1" "$board:blue:tricolor0" "wlan1"
        ;;
index 949f161..57d690d 100755 (executable)
@@ -230,6 +230,7 @@ ar71xx_setup_interfaces()
        dir-835-a1|\
        esr900|\
        mynet-n750|\
+       sr3200|\
        wndr3700v4|\
        wndr4300)
                ucidef_add_switch "switch0" \
@@ -395,7 +396,8 @@ ar71xx_setup_interfaces()
                ucidef_add_switch "switch0" \
                        "0@eth0" "1:lan" "2:wan"
                ;;
-       unifiac-pro)
+       unifiac-pro|\
+       xd3200)
                ucidef_add_switch "switch0" \
                        "0@eth0" "2:lan" "3:wan"
                ;;
index 9b9aea8..43ea2b6 100644 (file)
@@ -18,7 +18,9 @@ get_status_led() {
        antminer-s3|\
        antminer-r1|\
        minibox-v1|\
-       som9331)
+       som9331|\
+       sr3200|\
+       xd3200)
                status_led="$board:green:system"
                ;;
        ap132|\
index 7983dad..97875bd 100644 (file)
@@ -49,7 +49,9 @@ case "$FIRMWARE" in
        case $board in
        cf-e380ac-v1|\
        cf-e380ac-v2|\
-       dlan-pro-1200-ac)
+       dlan-pro-1200-ac|\
+       sr3200|\
+       xd3200)
                ath10kcal_extract "art" 20480 2116
                ;;
        dap-2695-a1)
index 526d033..c27cd13 100755 (executable)
@@ -905,6 +905,9 @@ ar71xx_board_detect() {
        *SOM9331)
                name="som9331"
                ;;
+       *SR3200)
+               name="sr3200"
+               ;;
        *TEW-632BRP)
                name="tew-632brp"
                ;;
@@ -1190,6 +1193,9 @@ ar71xx_board_detect() {
        *WHR-HP-G300N)
                name="whr-hp-g300n"
                ;;
+       *XD3200)
+               name="xd3200"
+               ;;
        *Z1)
                name="z1"
                ;;
index 5f4375d..7b59bf3 100755 (executable)
@@ -228,6 +228,7 @@ platform_check_image() {
        rocket-m-xw|\
        rocket-m|\
        rw2458n|\
+       sr3200|\
        tew-632brp|\
        tew-712br|\
        tew-732br|\
@@ -251,7 +252,8 @@ platform_check_image() {
        wzr-hp-ag300h|\
        wzr-hp-g300nh2|\
        wzr-hp-g300nh|\
-       wzr-hp-g450h)
+       wzr-hp-g450h|\
+       xd3200)
                [ "$magic" != "2705" ] && {
                        echo "Invalid image type."
                        return 1
index c6a757a..3181797 100644 (file)
@@ -150,6 +150,7 @@ CONFIG_ATH79_MACH_R6100=y
 CONFIG_ATH79_MACH_RW2458N=y
 CONFIG_ATH79_MACH_SMART_300=y
 CONFIG_ATH79_MACH_SOM9331=y
+CONFIG_ATH79_MACH_SR3200=y
 CONFIG_ATH79_MACH_TELLSTICK_ZNET_LITE=y
 CONFIG_ATH79_MACH_TEW_632BRP=y
 CONFIG_ATH79_MACH_TEW_673GRU=y
@@ -217,6 +218,7 @@ CONFIG_ATH79_MACH_WZR_HP_AG300H=y
 CONFIG_ATH79_MACH_WZR_HP_G300NH=y
 CONFIG_ATH79_MACH_WZR_HP_G300NH2=y
 CONFIG_ATH79_MACH_WZR_HP_G450H=y
+CONFIG_ATH79_MACH_XD3200=y
 CONFIG_ATH79_MACH_Z1=y
 CONFIG_ATH79_MACH_ZBT_WE1526=y
 CONFIG_ATH79_MACH_ZCN_1523H=y
index f1bfcb8..9e1b50e 100644 (file)
@@ -280,6 +280,17 @@ config ATH79_MACH_SOM9331
        select ATH79_DEV_USB
        select ATH79_DEV_WMAC
 
+config ATH79_MACH_SR3200
+       bool "YunCore SR3200 support"
+       select SOC_QCA956X
+       select ATH79_DEV_AP9X_PCI if PCI
+       select ATH79_DEV_ETH
+       select ATH79_DEV_GPIO_BUTTONS
+       select ATH79_DEV_LEDS_GPIO
+       select ATH79_DEV_M25P80
+       select ATH79_DEV_USB
+       select ATH79_DEV_WMAC
+
 config ATH79_MACH_BHR_4GRV2
        bool "Buffalo BHR-4GRV2 board support"
        select SOC_QCA955X
@@ -425,6 +436,16 @@ config ATH79_MACH_WPJ558
        select ATH79_DEV_USB
        select ATH79_DEV_WMAC
 
+config ATH79_MACH_XD3200
+       bool "YunCore XD3200 support"
+       select SOC_QCA956X
+       select ATH79_DEV_AP9X_PCI if PCI
+       select ATH79_DEV_ETH
+       select ATH79_DEV_GPIO_BUTTONS
+       select ATH79_DEV_LEDS_GPIO
+       select ATH79_DEV_M25P80
+       select ATH79_DEV_WMAC
+
 config ATH79_MACH_DGL_5500_A1
        bool "D-Link DGL-5500 A1 support"
        select SOC_QCA955X
index ac2dbbb..e573b4b 100644 (file)
@@ -156,6 +156,7 @@ obj-$(CONFIG_ATH79_MACH_RBSXTLITE)          += mach-rbsxtlite.o
 obj-$(CONFIG_ATH79_MACH_RW2458N)               += mach-rw2458n.o
 obj-$(CONFIG_ATH79_MACH_SMART_300)             += mach-smart-300.o
 obj-$(CONFIG_ATH79_MACH_SOM9331)               += mach-som9331.o
+obj-$(CONFIG_ATH79_MACH_SR3200)                        += mach-sr3200.o
 obj-$(CONFIG_ATH79_MACH_TELLSTICK_ZNET_LITE)   += mach-tellstick-znet-lite.o
 obj-$(CONFIG_ATH79_MACH_TEW_632BRP)            += mach-tew-632brp.o
 obj-$(CONFIG_ATH79_MACH_TEW_673GRU)            += mach-tew-673gru.o
@@ -223,6 +224,7 @@ obj-$(CONFIG_ATH79_MACH_WZR_HP_AG300H)              += mach-wzr-hp-ag300h.o
 obj-$(CONFIG_ATH79_MACH_WZR_HP_G300NH)         += mach-wzr-hp-g300nh.o
 obj-$(CONFIG_ATH79_MACH_WZR_HP_G300NH2)                += mach-wzr-hp-g300nh2.o
 obj-$(CONFIG_ATH79_MACH_WZR_HP_G450H)          += mach-wzr-hp-g450h.o
+obj-$(CONFIG_ATH79_MACH_XD3200)                        += mach-sr3200.o
 obj-$(CONFIG_ATH79_MACH_Z1)                    += mach-z1.o
 obj-$(CONFIG_ATH79_MACH_ZBT_WE1526)            += mach-zbt-we1526.o
 obj-$(CONFIG_ATH79_MACH_ZCN_1523H)             += mach-zcn-1523h.o
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-sr3200.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-sr3200.c
new file mode 100644 (file)
index 0000000..51fcccf
--- /dev/null
@@ -0,0 +1,187 @@
+/*
+ * Support for YunCore SR3200 and XD3200 boards
+ *
+ * Copyright (C) 2016 Piotr Dymacz <pepe2k@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/phy.h>
+#include <linux/gpio.h>
+#include <linux/ar8216_platform.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach-ath79/ath79.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "dev-ap9x-pci.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+
+#define SR3200_XD3200_GPIO_LED_SYSTEM  1
+#define SR3200_XD3200_GPIO_LED_WLAN2G  19
+
+#define SR3200_XD3200_GPIO_BTN_RESET   2
+
+#define SR3200_XD3200_KEYS_POLL_INTERVAL       20
+#define SR3200_XD3200_KEYS_DEBOUNCE_INTERVAL   \
+               (3 * SR3200_XD3200_KEYS_POLL_INTERVAL)
+
+static struct gpio_led xd3200_leds_gpio[] __initdata = {
+       {
+               .name           = "xd3200:green:system",
+               .gpio           = SR3200_XD3200_GPIO_LED_SYSTEM,
+               .active_low     = 1,
+       },
+       {
+               .name           = "xd3200:blue:wlan2g",
+               .gpio           = SR3200_XD3200_GPIO_LED_WLAN2G,
+               .active_low     = 1,
+       },
+};
+
+static struct gpio_led sr3200_leds_gpio[] __initdata = {
+       {
+               .name           = "sr3200:green:system",
+               .gpio           = SR3200_XD3200_GPIO_LED_SYSTEM,
+               .active_low     = 1,
+       },
+       {
+               .name           = "sr3200:green:wlan2g",
+               .gpio           = SR3200_XD3200_GPIO_LED_WLAN2G,
+               .active_low     = 1,
+       },
+};
+
+static struct gpio_keys_button sr3200_xd3200_gpio_keys[] __initdata = {
+       {
+               .desc           = "reset",
+               .type           = EV_KEY,
+               .code           = KEY_RESTART,
+               .debounce_interval = SR3200_XD3200_KEYS_DEBOUNCE_INTERVAL,
+               .gpio           = SR3200_XD3200_GPIO_BTN_RESET,
+               .active_low     = 1,
+       },
+};
+
+static const struct ar8327_led_info sr3200_leds_qca833x[] = {
+       AR8327_LED_INFO(PHY0_0, HW, "sr3200:green:lan1"),
+       AR8327_LED_INFO(PHY1_0, HW, "sr3200:green:lan2"),
+       AR8327_LED_INFO(PHY2_0, HW, "sr3200:green:lan3"),
+       AR8327_LED_INFO(PHY3_0, HW, "sr3200:green:lan4"),
+       AR8327_LED_INFO(PHY4_0, HW, "sr3200:green:wan"),
+};
+
+static const struct ar8327_led_info xd3200_leds_qca833x[] = {
+       AR8327_LED_INFO(PHY1_0, HW, "xd3200:green:lan"),
+       AR8327_LED_INFO(PHY2_0, HW, "xd3200:green:wan"),
+};
+
+/* Blink rate: 1 Gbps -> 8 hz, 100 Mbs -> 4 Hz, 10 Mbps -> 2 Hz */
+static struct ar8327_led_cfg sr3200_xd3200_qca833x_led_cfg = {
+       .led_ctrl0 = 0xcf37cf37,
+       .led_ctrl1 = 0xcf37cf37,
+       .led_ctrl2 = 0xcf37cf37,
+       .led_ctrl3 = 0x0,
+       .open_drain = true,
+};
+
+static struct ar8327_pad_cfg sr3200_xd3200_qca833x_pad0_cfg = {
+       .mode = AR8327_PAD_MAC_SGMII,
+       .sgmii_delay_en = true,
+};
+
+static struct ar8327_platform_data sr3200_xd3200_qca833x_data = {
+       .pad0_cfg = &sr3200_xd3200_qca833x_pad0_cfg,
+       .port0_cfg = {
+               .force_link = 1,
+               .speed = AR8327_PORT_SPEED_1000,
+               .duplex = 1,
+               .txpause = 1,
+               .rxpause = 1,
+       },
+       .led_cfg = &sr3200_xd3200_qca833x_led_cfg,
+};
+
+static struct mdio_board_info sr3200_xd3200_mdio0_info[] = {
+       {
+               .bus_id = "ag71xx-mdio.0",
+               .phy_addr = 0,
+               .platform_data = &sr3200_xd3200_qca833x_data,
+       },
+};
+
+static void __init sr3200_xd3200_common_setup(void)
+{
+       u8 *mac = (u8 *) KSEG1ADDR(0x1fff0000);
+
+       ath79_register_m25p80(NULL);
+
+       ath79_register_mdio(0, 0x0);
+       mdiobus_register_board_info(sr3200_xd3200_mdio0_info,
+                                   ARRAY_SIZE(sr3200_xd3200_mdio0_info));
+
+       /* GMAC0 is connected to QCA8334/QCA8337N switch */
+       ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+       ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
+       ath79_eth0_data.phy_mask = BIT(0);
+       ath79_eth0_data.speed = SPEED_1000;
+       ath79_eth0_data.duplex = DUPLEX_FULL;
+
+       ath79_init_mac(ath79_eth0_data.mac_addr, mac, 0);
+       ath79_register_eth(0);
+
+       ath79_register_wmac(mac + 0x1000, NULL);
+
+       ap91_pci_init(mac + 0x5000, NULL);
+
+       ath79_gpio_direction_select(SR3200_XD3200_GPIO_LED_SYSTEM, true);
+       ath79_gpio_direction_select(SR3200_XD3200_GPIO_LED_WLAN2G, true);
+
+       /* Mute LEDs on boot */
+       gpio_set_value(SR3200_XD3200_GPIO_LED_SYSTEM, 1);
+       gpio_set_value(SR3200_XD3200_GPIO_LED_WLAN2G, 1);
+
+       ath79_gpio_output_select(SR3200_XD3200_GPIO_LED_SYSTEM, 0);
+       ath79_gpio_output_select(SR3200_XD3200_GPIO_LED_WLAN2G, 0);
+
+       ath79_register_gpio_keys_polled(-1, SR3200_XD3200_KEYS_POLL_INTERVAL,
+                                       ARRAY_SIZE(sr3200_xd3200_gpio_keys),
+                                       sr3200_xd3200_gpio_keys);
+}
+
+static void __init sr3200_setup(void)
+{
+       sr3200_xd3200_qca833x_data.leds = sr3200_leds_qca833x;
+       sr3200_xd3200_qca833x_data.num_leds = ARRAY_SIZE(sr3200_leds_qca833x);
+
+       sr3200_xd3200_common_setup();
+
+       ath79_register_leds_gpio(-1, ARRAY_SIZE(sr3200_leds_gpio),
+                                sr3200_leds_gpio);
+
+       ath79_register_usb();
+}
+
+MIPS_MACHINE(ATH79_MACH_SR3200, "SR3200", "YunCore SR3200", sr3200_setup);
+
+static void __init xd3200_setup(void)
+{
+       sr3200_xd3200_qca833x_data.leds = xd3200_leds_qca833x;
+       sr3200_xd3200_qca833x_data.num_leds = ARRAY_SIZE(xd3200_leds_qca833x);
+
+       sr3200_xd3200_common_setup();
+
+       ath79_register_leds_gpio(-1, ARRAY_SIZE(xd3200_leds_gpio),
+                                xd3200_leds_gpio);
+}
+
+MIPS_MACHINE(ATH79_MACH_XD3200, "XD3200", "YunCore XD3200", xd3200_setup);
index 9a8da22..0054067 100644 (file)
@@ -173,6 +173,7 @@ enum ath79_mach_type {
        ATH79_MACH_RW2458N,                     /* Redwave RW2458N */
        ATH79_MACH_SMART_300,                   /* NC-LINK SMART-300 */
        ATH79_MACH_SOM9331,                     /* OpenEmbed SOM9331 */
+       ATH79_MACH_SR3200,                      /* YunCore SR3200 */
        ATH79_MACH_TELLSTICK_ZNET_LITE,         /* TellStick ZNet Lite */
        ATH79_MACH_TEW_632BRP,                  /* TRENDnet TEW-632BRP */
        ATH79_MACH_TEW_673GRU,                  /* TRENDnet TEW-673GRU */
@@ -282,6 +283,7 @@ enum ath79_mach_type {
        ATH79_MACH_WZR_HP_G300NH,               /* Buffalo WZR-HP-G300NH */
        ATH79_MACH_WZR_HP_G300NH2,              /* Buffalo WZR-HP-G300NH2 */
        ATH79_MACH_WZR_HP_G450H,                /* Buffalo WZR-HP-G450H */
+       ATH79_MACH_XD3200,                      /* YunCore XD3200 */
        ATH79_MACH_Z1,                          /* Cisco Meraki Z1 */
        ATH79_MACH_ZBT_WE1526,                  /* Zbtlink ZBT-WE1526 */
        ATH79_MACH_ZCN_1523H_2,                 /* Zcomax ZCN-1523H-2-xx */
index 6ceabeb..e2867e6 100644 (file)
@@ -484,6 +484,24 @@ define Device/som9331
 endef
 TARGET_DEVICES += som9331
 
+define Device/sr3200
+  DEVICE_TITLE := YunCore SR3200
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k ath10k-firmware-qca988x
+  BOARDNAME = SR3200
+  IMAGE_SIZE = 16000k
+  CONSOLE = ttyS0,115200
+  MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env),16000k(firmware),64k(art)ro
+endef
+TARGET_DEVICES += sr3200
+
+define Device/xd3200
+  $(Device/sr3200)
+  DEVICE_TITLE := YunCore XD3200
+  DEVICE_PACKAGES := kmod-ath10k ath10k-firmware-qca988x
+  BOARDNAME = XD3200
+endef
+TARGET_DEVICES += xd3200
+
 define Device/tellstick-znet-lite
   $(Device/tplink-16mlzma)
   DEVICE_TITLE := TellStick ZNet Lite