ath79: add support for TP-Link Archer C6 v2
authorGeorgi Vlaev <georgi.vlaev@gmail.com>
Fri, 28 Dec 2018 08:24:01 +0000 (10:24 +0200)
committerMathias Kresin <dev@kresin.me>
Mon, 31 Dec 2018 15:25:11 +0000 (16:25 +0100)
This patch adds support for TP-Link Archer C6 v2 (EU)

Hardware specification:
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q64CSIG (8MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
  - 2.4GHz (bgn) QCA9563 integrated (3x3)
  - 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: There's no UART header on the board

Flash instructions:

Upload
openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin
via the router Web interface.

Flash instruction using tftp recovery:

1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
   tftp root directory renamed to ArcherC6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the reset
   button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing

According to the GPL source the non-EU variant has different
GPIOs assigned to some of the LEDs and buttons. The flash
layout might be different as well. The wikidevi entry for
Archer A6/C6 assumes they are identical.

Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
target/linux/ath79/base-files/etc/board.d/01_leds
target/linux/ath79/base-files/etc/board.d/02_network
target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
target/linux/ath79/dts/qca9563_tplink_archer-c6-v2.dts [new file with mode: 0644]
target/linux/ath79/dts/qca9563_tplink_archer-x6-v2.dtsi [new file with mode: 0644]
target/linux/ath79/image/generic-tp-link.mk
tools/firmware-utils/src/tplink-safeloader.c

index 87c9c29..fa7fe71 100755 (executable)
@@ -76,6 +76,10 @@ tplink,archer-c59-v1)
        ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x1E"
        ucidef_set_led_netdev "wan" "WAN" "tp-link:green:wan" "eth0"
        ;;
+tplink,archer-c6-v2)
+       ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x3C"
+       ucidef_set_led_switch "wan" "WAN" "tp-link:green:wan" "switch0" "0x02"
+       ;;
 tplink,re450-v2)
        ucidef_set_led_netdev "lan_data" "LAN Data" "tp-link:green:lan_data" "eth0" "tx rx"
        ucidef_set_led_netdev "lan_link" "LAN Link" "tp-link:green:lan_link" "eth0" "link"
index 3316607..e24c58e 100755 (executable)
@@ -154,6 +154,7 @@ ath79_setup_interfaces()
                        "0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
                ;;
        tplink,archer-a7-v5|\
+       tplink,archer-c6-v2|\
        tplink,archer-c7-v5|\
        tplink,tl-wdr3600|\
        tplink,tl-wdr4300)
index d9ce0c9..441893a 100644 (file)
@@ -155,7 +155,8 @@ case "$FIRMWARE" in
                        /lib/firmware/ath10k/QCA9888/hw2.0/board.bin
                ;;
        tplink,archer-c58-v1|\
-       tplink,archer-c59-v1)
+       tplink,archer-c59-v1|\
+       tplink,archer-c6-v2)
                ath10kcal_extract "art" 20480 12064
                ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary mac 8) -1)
                ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
diff --git a/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2.dts b/target/linux/ath79/dts/qca9563_tplink_archer-c6-v2.dts
new file mode 100644 (file)
index 0000000..5caec6f
--- /dev/null
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "qca9563_tplink_archer-x6-v2.dtsi"
+
+/ {
+       compatible = "tplink,archer-c6-v2", "qca,qca9563";
+       model = "TP-Link Archer C6 v2";
+};
diff --git a/target/linux/ath79/dts/qca9563_tplink_archer-x6-v2.dtsi b/target/linux/ath79/dts/qca9563_tplink_archer-x6-v2.dtsi
new file mode 100644 (file)
index 0000000..37ab164
--- /dev/null
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca956x.dtsi"
+
+/ {
+       chosen {
+               bootargs = "console=ttyS0,115200n8";
+       };
+
+       aliases {
+               led-boot = &power;
+               led-failsafe = &power;
+               led-running = &power;
+               led-upgrade = &power;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               power: power {
+                       label = "tp-link:green:power";
+                       gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+                       default-state = "on";
+               };
+
+               wlan2g {
+                       label = "tp-link:green:wlan2g";
+                       gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy1tpt";
+               };
+
+               wlan5g {
+                       label = "tp-link:green:wlan5g";
+                       gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy0tpt";
+               };
+
+               lan {
+                       label = "tp-link:green:lan";
+                       gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
+               };
+
+               wan {
+                       label = "tp-link:green:wan";
+                       gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+               };
+
+               wan_fail {
+                       label = "tp-link:amber:wan";
+                       gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+               };
+
+               wps {
+                       label = "tp-link:green:wps";
+                       gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       label = "Reset button";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+                       debounce-interval = <60>;
+               };
+
+               wps {
+                       label = "WPS button";
+                       linux,code = <KEY_WPS_BUTTON>;
+                       gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+                       debounce-interval = <60>;
+               };
+       };
+};
+
+&pcie {
+       status = "okay";
+};
+
+&uart {
+       status = "okay";
+};
+
+&gpio {
+       status = "okay";
+};
+
+&spi {
+       status = "okay";
+       num-cs = <1>;
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <25000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "u-boot";
+                               reg = <0x000000 0x020000>;
+                               read-only;
+                       };
+
+                       mac: partition@20000 {
+                               label = "mac";
+                               reg = <0x020000 0x010000>;
+                               read-only;
+                       };
+
+                       partition@30000 {
+                               compatible = "denx,uimage";
+                               label = "firmware";
+                               reg = <0x030000 0x7a0000>;
+                       };
+
+                       partition@7d0000 {
+                               label = "tplink";
+                               reg = <0x7d0000 0x020000>;
+                               read-only;
+                       };
+
+                       art: partition@7f0000 {
+                               label = "art";
+                               reg = <0x7f0000 0x010000>;
+                               read-only;
+                       };
+               };
+       };
+};
+
+&mdio0 {
+       status = "okay";
+
+       phy-mask = <0>;
+
+       phy0: ethernet-phy@0 {
+               reg = <0>;
+               phy-mode = "sgmii";
+
+               qca,ar8327-initvals = <
+                       0x04 0x00080080 /* PORT0 PAD MODE CTRL */
+                       0x7c 0x0000007e /* PORT0_STATUS */
+                       >;
+       };
+};
+
+&eth0 {
+       status = "okay";
+
+       phy-mode = "sgmii";
+       mtd-mac-address = <&mac 0x8>;
+       phy-handle = <&phy0>;
+};
+
+&wmac {
+       status = "okay";
+
+       mtd-cal-data = <&art 0x1000>;
+       mtd-mac-address = <&mac 0x8>;
+};
index 093ac72..be755c7 100644 (file)
@@ -34,6 +34,16 @@ define Device/tplink_archer-c59-v1
 endef
 TARGET_DEVICES += tplink_archer-c59-v1
 
+define Device/tplink_archer-c6-v2
+  $(Device/tplink-safeloader-uimage)
+  ATH_SOC := qca9563
+  IMAGE_SIZE := 7808k
+  DEVICE_TITLE := TP-LINK Archer C6 v2
+  TPLINK_BOARD_ID := ARCHER-C6-V2
+  DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
+endef
+TARGET_DEVICES += tplink_archer-c6-v2
+
 define Device/tplink_archer-c7-v1
   $(Device/tplink-8mlzma)
   ATH_SOC := qca9558
index 358247e..74ea697 100644 (file)
@@ -548,6 +548,42 @@ static struct device_info boards[] = {
                .last_sysupgrade_partition = "file-system",
        },
 
+       /** Firmware layout for the C6v2 */
+       {
+               .id     = "ARCHER-C6-V2",
+               .vendor = "",
+               .support_list =
+                       "SupportList:\r\n"
+                       "{product_name:Archer C6,product_ver:2.0.0,special_id:45550000}\r\n"
+                       "{product_name:Archer C6,product_ver:2.0.0,special_id:52550000}\r\n"
+                       "{product_name:Archer C6,product_ver:2.0.0,special_id:4A500000}\r\n",
+               .support_trail = '\x00',
+               .soft_ver = "soft_ver:1.0.0\n",
+
+               .partitions = {
+                       {"fs-uboot", 0x00000, 0x20000},
+                       {"default-mac", 0x20000, 0x00200},
+                       {"pin", 0x20200, 0x00100},
+                       {"product-info", 0x20300, 0x00200},
+                       {"device-id", 0x20500, 0x0fb00},
+                       {"firmware", 0x30000, 0x7a9400},
+                       {"soft-version", 0x7d9400, 0x00100},
+                       {"extra-para", 0x7d9500, 0x00100},
+                       {"support-list", 0x7d9600, 0x00200},
+                       {"profile", 0x7d9800, 0x03000},
+                       {"default-config", 0x7dc800, 0x03000},
+                       {"partition-table", 0x7df800, 0x00800},
+                       {"user-config", 0x7e0000, 0x0c000},
+                       {"certificate", 0x7ec000, 0x04000},
+                       {"radio", 0x7f0000, 0x10000},
+                       {NULL, 0, 0}
+               },
+
+               .first_sysupgrade_partition = "os-image",
+               .last_sysupgrade_partition = "file-system",
+       },
+
+
        /** Firmware layout for the C60v1 */
        {
                .id     = "ARCHER-C60-V1",
@@ -1624,6 +1660,9 @@ static void build_image(const char *output,
        } else if (strcasecmp(info->id, "ARCHER-A7-V5") == 0 || strcasecmp(info->id, "ARCHER-C7-V4") == 0 || strcasecmp(info->id, "ARCHER-C7-V5") == 0) {
                const char mdat[11] = {0x01, 0x00, 0x00, 0x02, 0x00, 0x00, 0xca, 0x00, 0x01, 0x00, 0x00};
                parts[5] = put_data("extra-para", mdat, 11);
+       } else if (strcasecmp(info->id, "ARCHER-C6-V2") == 0) {
+               const char mdat[11] = {0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00};
+               parts[5] = put_data("extra-para", mdat, 11);
        }
 
        size_t len;