ramips: add support for ELECOM WRC-1167GHBK2-S
authorINAGAKI Hiroshi <musashino.open@gmail.com>
Fri, 15 Jun 2018 15:27:51 +0000 (00:27 +0900)
committerMathias Kresin <dev@kresin.me>
Tue, 19 Jun 2018 20:46:04 +0000 (22:46 +0200)
ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Cores, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
  - MediaTek MT7615D
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 2x keys
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 57600 bps

Flash instruction using factory image:

1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin"
2. Connect the computer to the LAN port of WRC-1167GHBK2-S
3. Connect power cable to WRC-1167GHBK2-S and turn on it
4. Access to "http://192.168.2.1/details.html" and open firmware
update page ("手動更新(アップデート)")
5. Select the factory image and click apply ("適用") button
6. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
target/linux/ramips/base-files/etc/board.d/01_leds
target/linux/ramips/base-files/etc/board.d/02_network
target/linux/ramips/base-files/etc/diag.sh
target/linux/ramips/base-files/lib/upgrade/platform.sh
target/linux/ramips/dts/WRC-1167GHBK2-S.dts [new file with mode: 0644]
target/linux/ramips/image/mt7621.mk

index a9a68f6..54504c6 100755 (executable)
@@ -168,6 +168,7 @@ dlink,dwr-921-c1)
        ucidef_set_led_default "sigstrength" "Signal Strength" "$boardname:green:sigstrength" "0"
        ;;
 dir-810l|\
+elecom,wrc-1167ghbk2-s|\
 iodata,wn-gx300gr|\
 mzk-750dhp|\
 mzk-dp150n|\
index 49d7f92..de086cf 100755 (executable)
@@ -226,7 +226,8 @@ ramips_setup_interfaces()
                ucidef_add_switch "switch0" \
                        "1:lan:3" "2:lan:4" "3:lan:1" "4:lan:2" "0:wan" "6@eth0"
                ;;
-       dir-860l-b1)
+       dir-860l-b1|\
+       elecom,wrc-1167ghbk2-s)
                ucidef_add_switch "switch0" \
                        "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "0:wan" "6@eth0"
                ;;
@@ -450,6 +451,10 @@ ramips_setup_macs()
        e1700)
                wan_mac=$(mtd_get_mac_ascii config WAN_MAC_ADDR)
                ;;
+       elecom,wrc-1167ghbk2-s|\
+       sk-wb8)
+               wan_mac=$(mtd_get_mac_binary factory 57350)
+               ;;
        gl-mt300n-v2|\
        whr-g300n)
                wan_mac=$(mtd_get_mac_binary factory 4)
@@ -514,9 +519,6 @@ ramips_setup_macs()
                lan_mac=$(macaddr_setbit_la "$lan_mac")
                wan_mac=$(mtd_get_mac_binary factory 32772)
                ;;
-       sk-wb8)
-               wan_mac=$(mtd_get_mac_binary factory 57350)
-               ;;
        tew-691gr)
                wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 4)" 3)
                ;;
index e5373a8..eb06442 100644 (file)
@@ -22,6 +22,7 @@ get_status_led() {
        dch-m225|\
        dir-860l-b1|\
        e1700|\
+       elecom,wrc-1167ghbk2-s|\
        ex2700|\
        ex3700|\
        fonera20n|\
index 9b17ecb..c094e41 100755 (executable)
@@ -54,6 +54,7 @@ platform_check_image() {
        dir-810l|\
        duzun-dm06|\
        e1700|\
+       elecom,wrc-1167ghbk2-s|\
        esr-9753|\
        ew1200|\
        ex2700|\
diff --git a/target/linux/ramips/dts/WRC-1167GHBK2-S.dts b/target/linux/ramips/dts/WRC-1167GHBK2-S.dts
new file mode 100644 (file)
index 0000000..7b1cfd7
--- /dev/null
@@ -0,0 +1,144 @@
+/dts-v1/;
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       compatible = "elecom,wrc-1167ghbk2-s", "mediatek,mt7621-soc";
+       model = "ELECOM WRC-1167GHBK2-S";
+
+       memory@0 {
+               device_type = "memory";
+               reg = <0x0 0x8000000>;
+       };
+
+       chosen {
+               bootargs = "console=ttyS0,57600";
+       };
+
+       gpio-leds {
+               compatible = "gpio-leds";
+
+               wlan2g {
+                       label = "wrc-1167ghbk2-s:white:wlan2g";
+                       gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+               };
+
+               wlan5g {
+                       label = "wrc-1167ghbk2-s:white:wlan5g";
+                       gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
+               };
+
+               power_green {
+                       label = "wrc-1167ghbk2-s:green:power";
+                       gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+               };
+
+               power_blue {
+                       label = "wrc-1167ghbk2-s:blue:power";
+                       gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
+               };
+
+               wps {
+                       label = "wrc-1167ghbk2-s:red:wps";
+                       gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+               };
+
+               power_red {
+                       label = "wrc-1167ghbk2-s:red:power";
+                       gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+               };
+       };
+
+       gpio-keys-polled {
+               compatible = "gpio-keys-polled";
+               #address-cells = <1>;
+               #size-cells = <0>;
+               poll-interval = <20>;
+
+               reset {
+                       label = "reset";
+                       gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+               };
+
+               wps {
+                       label = "wps";
+                       gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
+               };
+       };
+};
+
+&ethernet {
+       mtd-mac-address = <&factory 0xe000>;
+};
+
+&spi0 {
+       status = "okay";
+
+       m25p80@0 {
+               #address-cells = <1>;
+               #size-cells = <1>;
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <10000000>;
+               m25p,chunked-io = <32>;
+
+               partition@0 {
+                       label = "u-boot";
+                       reg = <0x0 0x30000>;
+                       read-only;
+               };
+
+               partition@30000 {
+                       label = "u-boot-env";
+                       reg = <0x30000 0x10000>;
+                       read-only;
+               };
+
+               factory: partition@40000 {
+                       label = "factory";
+                       reg = <0x40000 0x10000>;
+                       read-only;
+               };
+
+               partition@50000 {
+                       label = "firmware";
+                       reg = <0x50000 0xf20000>;
+               };
+
+               partition@f70000 {
+                       label = "user_data";
+                       reg = <0xf70000 0x80000>;
+                       read-only;
+               };
+
+               partition@ff0000 {
+                       label = "NVRAM";
+                       reg = <0xff0000 0x10000>;
+                       read-only;
+               };
+       };
+};
+
+&pinctrl {
+       state_default: pinctrl0 {
+               gpio {
+                       ralink,group = "i2c", "uart3", "jtag", "wdt";
+                       ralink,function = "gpio";
+               };
+       };
+};
+
+&pcie {
+       status = "okay";
+       // WRC-1167GHBK2-S has MT7615D for 2.4/5 GHz wifi,
+       // but it's not supported in OpenWrt.
+};
+
+&xhci {
+       status = "disabled";
+};
index f8fb281..f6f8ea0 100644 (file)
@@ -4,6 +4,18 @@
 
 DEVICE_VARS += TPLINK_BOARD_ID TPLINK_HEADER_VERSION TPLINK_HWID TPLINK_HWREV
 
+define Build/elecom-wrc-factory
+  $(eval product=$(word 1,$(1)))
+  $(eval version=$(word 2,$(1)))
+  $(STAGING_DIR_HOST)/bin/mkhash md5 $@ >> $@
+  ( \
+    echo -n "ELECOM $(product) v$(version)" | \
+      dd bs=32 count=1 conv=sync; \
+    dd if=$@; \
+  ) > $@.new
+  mv $@.new $@
+endef
+
 define Build/ubnt-erx-factory-image
        if [ -e $(KDIR)/tmp/$(KERNEL_INITRAMFS_IMAGE) -a "$$(stat -c%s $@)" -lt "$(KERNEL_SIZE)" ]; then \
                echo '21001:6' > $(1).compat; \
@@ -65,6 +77,16 @@ define Device/mediatek_ap-mt7621a-v60
 endef
 TARGET_DEVICES += mediatek_ap-mt7621a-v60
 
+define Device/elecom_wrc-1167ghbk2-s
+  DTS := WRC-1167GHBK2-S
+  IMAGE_SIZE := 15488k
+  DEVICE_TITLE := ELECOM WRC-1167GHBK2-S
+  IMAGES += factory.bin
+  IMAGE/factory.bin := $$(sysupgrade_bin) | check-size $$$$(IMAGE_SIZE) |\
+    elecom-wrc-factory WRC-1167GHBK2-S 0.00
+endef
+TARGET_DEVICES += elecom_wrc-1167ghbk2-s
+
 define Device/ew1200
   DTS := EW1200
   IMAGE_SIZE := $(ralink_default_fw_size_16M)