ar71xx: add support for the MikroTik RB911-2Hn/5Hn boards
authorGabor Juhos <juhosg@freemail.hu>
Thu, 18 Jan 2018 12:50:32 +0000 (13:50 +0100)
committerJohn Crispin <john@phrozen.org>
Mon, 22 Jan 2018 09:53:45 +0000 (10:53 +0100)
The patch adds support for the MikroTik RB911-2Hn (911 Lite2)
and the RB911-5Hn (911 Lite5) boards:

  https://mikrotik.com/product/RB911-2Hn
  https://mikrotik.com/product/RB911-5Hn

The two boards are using the same hardware design, the only difference
between the two is the supported wireless band.

Specifications:
  * SoC: Atheros AR9344 (600MHz)
  * RAM: 64MiB
  * Storage: 16 MiB SPI NOR flash
  * Ethernet: 1x100M (Passive PoE in)
  * Wireless: AR9344 built-in wireless MAC, single chain
              802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn)

Notes:
  * Older versions of these boards might be equipped with a NAND
    flash chip instead of the SPI NOR device. Those boards are not
    supported (yet).
  * The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the
    same hardware. Support for that can be added later with little
    effort probably.

Installation:

1. Setup a DHCP/BOOTP Server with the following parameters:
   * DHCP-Option 66 (TFTP server name): pointing to a local TFTP
     server within the same subnet of the DHCP range
   * DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
     of the to be booted image. The usable intramfs files are:
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
       - openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin

2. Press the reset button on the board and keep that pressed.

3. Connect the board to your local network via its ethernet port.

4. Release the button after the LEDs on the board are turned off.
   Now the board should load and start the initramfs image from
   the TFTP server.

5. Upload the sysupgrade image to the board with scp:
     $ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin

5. Log in to the running system listening on 192.168.1.1 via ssh
   as root (without password):
     $ ssh root@192.168.1.1

7. Flash the uploaded firmware file from the ssh session via the
   sysupgrade command:
     root@OpenWrt:~# sysupgrade /tmp/fw.bin

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
target/linux/ar71xx/base-files/etc/board.d/01_leds
target/linux/ar71xx/base-files/etc/board.d/02_network
target/linux/ar71xx/base-files/etc/diag.sh
target/linux/ar71xx/base-files/lib/ar71xx.sh
target/linux/ar71xx/base-files/lib/upgrade/platform.sh
target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
target/linux/ar71xx/files/arch/mips/ath79/mach-rbspi.c
target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
target/linux/ar71xx/image/mikrotik.mk
target/linux/ar71xx/patches-4.4/701-MIPS-ath79-add-routerboard-detection.patch
target/linux/ar71xx/patches-4.9/701-MIPS-ath79-add-routerboard-detection.patch

index fb1f29d..ecd3723 100755 (executable)
@@ -292,6 +292,10 @@ rb-750up-r2)
        ucidef_set_led_switch "port4" "port3" "rb:green:port4" "switch0" "0x04"
        ucidef_set_led_switch "port5" "port5" "rb:green:port5" "switch0" "0x02"
        ;;
+rb-911-2hn|\
+rb-911-5hn)
+       ucidef_set_led_netdev "eth" "ETH" "rb:green:eth" "eth0"
+       ;;
 rb-941-2nd)
        ucidef_set_led_timer "user" "USR/ACT" "rb:green:user" "1000" "1000"
        ;;
index 5a10a9f..b0755c4 100755 (executable)
@@ -93,6 +93,8 @@ ar71xx_setup_interfaces()
        pqi-air-pen|\
        rb-411|\
        rb-411u|\
+       rb-911-2hn|\
+       rb-911-5hn|\
        rb-911g-2hpnd|\
        rb-911g-5hpacd|\
        rb-911g-5hpnd|\
index 2720288..4f4a73c 100644 (file)
@@ -319,6 +319,8 @@ get_status_led() {
        rb-750-r2|\
        rb-750p-pbr2|\
        rb-750up-r2|\
+       rb-911-2hn|\
+       rb-911-5hn|\
        rb-911g-2hpnd|\
        rb-911g-5hpacd|\
        rb-911g-5hpnd|\
index b664249..73bdce5 100755 (executable)
@@ -941,6 +941,12 @@ ar71xx_board_detect() {
        *"RouterBOARD 751G")
                name="rb-751g"
                ;;
+       *"RouterBOARD 911-2Hn")
+               name="rb-911-2hn"
+               ;;
+       *"RouterBOARD 911-5Hn")
+               name="rb-911-5hn"
+               ;;
        *"RouterBOARD 911G-2HPnD")
                name="rb-911g-2hpnd"
                ;;
index 3d7b159..1f9ed76 100755 (executable)
@@ -660,6 +660,8 @@ platform_check_image() {
        rb-750-r2|\
        rb-750p-pbr2|\
        rb-750up-r2|\
+       rb-911-2hn|\
+       rb-911-5hn|\
        rb-941-2nd|\
        rb-951ui-2nd|\
        rb-952ui-5ac2nd|\
@@ -723,6 +725,8 @@ platform_pre_upgrade() {
        rb-750-r2|\
        rb-750p-pbr2|\
        rb-750up-r2|\
+       rb-911-2hn|\
+       rb-911-5hn|\
        rb-941-2nd|\
        rb-951ui-2nd|\
        rb-952ui-5ac2nd|\
index 3ca7755..caaaf97 100644 (file)
@@ -1054,6 +1054,8 @@ config ATH79_MACH_RBSPI
        select ATH79_ROUTERBOOT
        help
          Say 'Y' here if you want your kernel to support the
+         MikroTik ROuterBOARD 911-2Hn (911 Lite2)
+         MikroTik ROuterBOARD 911-5Hn (911 Lite5)
          MikroTik RouterBOARD mAP
          MikroTik RouterBOARD mAP lite
          MikroTik RouterBOARD hAP lite
index 25e920f..f7f3b02 100644 (file)
@@ -3,6 +3,8 @@
  *
  *  - MikroTik RouterBOARD mAP 2nD
  *  - MikroTik RouterBOARD mAP L-2nD
+ *  - MikroTik RouterBOARD 911-2Hn (911 Lite2)
+ *  - MikroTik RouterBOARD 911-5Hn (911 Lite5)
  *  - MikroTik RouterBOARD 941L-2nD
  *  - MikroTik RouterBOARD 951Ui-2nD
  *  - MikroTik RouterBOARD 952Ui-5ac2nD
@@ -509,6 +511,56 @@ static struct platform_device rbwapgsc_phy_device = {
        },
 };
 
+/* RB911L GPIOs */
+#define RB911L_GPIO_BTN_RESET  15
+#define RB911L_GPIO_LED_1      13
+#define RB911L_GPIO_LED_2      12
+#define RB911L_GPIO_LED_3      4
+#define RB911L_GPIO_LED_4      21
+#define RB911L_GPIO_LED_5      18
+#define RB911L_GPIO_LED_ETH    20
+#define RB911L_GPIO_LED_POWER  11
+#define RB911L_GPIO_LED_USER   3
+#define RB911L_GPIO_PIN_HOLE   14 /* for reference */
+
+static struct gpio_led rb911l_leds[] __initdata = {
+       {
+               .name = "rb:green:eth",
+               .gpio = RB911L_GPIO_LED_ETH,
+               .active_low = 1,
+       }, {
+               .name = "rb:green:led1",
+               .gpio = RB911L_GPIO_LED_1,
+               .active_low = 1,
+       }, {
+               .name = "rb:green:led2",
+               .gpio = RB911L_GPIO_LED_2,
+               .active_low = 1,
+       }, {
+               .name = "rb:green:led3",
+               .gpio = RB911L_GPIO_LED_3,
+               .active_low = 1,
+       }, {
+               .name = "rb:green:led4",
+               .gpio = RB911L_GPIO_LED_4,
+               .active_low = 1,
+       }, {
+               .name = "rb:green:led5",
+               .gpio = RB911L_GPIO_LED_5,
+               .active_low = 1,
+       }, {
+               .name = "rb:green:power",
+               .gpio = RB911L_GPIO_LED_POWER,
+               .default_state = LEDS_GPIO_DEFSTATE_ON,
+               .open_drain = 1,
+       }, {
+               .name = "rb:green:user",
+               .gpio = RB911L_GPIO_LED_USER,
+               .active_low = 1,
+               .open_drain = 1,
+       },
+};
+
 static struct gen_74x164_chip_platform_data rbspi_ssr_data = {
        .base = RBSPI_SSR_GPIO_BASE,
        .num_registers = 1,
@@ -1015,8 +1067,53 @@ static void __init rbwapgsc_setup(void)
                        rbwapgsc_leds);
 }
 
+/*
+ * Setup the 911L hardware (AR9344).
+ */
+static void __init rb911l_setup(void)
+{
+       const struct rb_info *info;
+
+       info = rbspi_platform_setup();
+       if (!info)
+               return;
+
+       if (!rb_has_hw_option(info, RB_HW_OPT_NO_NAND)) {
+               /*
+                * Old hardware revisions might be equipped with a NAND flash
+                * chip instead of the 16MiB SPI NOR device. Those boards are
+                * not supported at the moment, so throw a warning and skip
+                * the peripheral setup to avoid messing up the data in the
+                * flash chip.
+                */
+               WARN(1, "The NAND flash on this board is not supported.\n");
+       } else {
+               rbspi_peripherals_setup(0);
+       }
+
+       ath79_register_mdio(1, 0x0);
+
+       ath79_init_mac(ath79_eth1_data.mac_addr, ath79_mac_base, 0);
+
+       ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
+       ath79_eth1_data.speed = SPEED_1000;
+       ath79_eth1_data.duplex = DUPLEX_FULL;
+
+       ath79_register_eth(1);
+
+       rbspi_wlan_init(0, 1);
+
+       rbspi_register_reset_button(RB911L_GPIO_BTN_RESET);
+
+       /* Make the eth LED controllable by software. */
+       ath79_gpio_output_select(RB911L_GPIO_LED_ETH, AR934X_GPIO_OUT_GPIO);
+
+       ath79_register_leds_gpio(-1, ARRAY_SIZE(rb911l_leds), rb911l_leds);
+}
+
 MIPS_MACHINE_NONAME(ATH79_MACH_RB_MAPL, "map-hb", rbmapl_setup);
 MIPS_MACHINE_NONAME(ATH79_MACH_RB_941, "H951L", rbhapl_setup);
+MIPS_MACHINE_NONAME(ATH79_MACH_RB_911L, "911L", rb911l_setup);
 MIPS_MACHINE_NONAME(ATH79_MACH_RB_952, "952-hb", rb952_setup);
 MIPS_MACHINE_NONAME(ATH79_MACH_RB_962, "962", rb962_setup);
 MIPS_MACHINE_NONAME(ATH79_MACH_RB_750UPR2, "750-hb", rb750upr2_setup);
index a621fe2..394be00 100644 (file)
@@ -190,6 +190,7 @@ enum ath79_mach_type {
        ATH79_MACH_RB_750UPR2,                  /* MikroTik RouterBOARD 750UP r2 */
        ATH79_MACH_RB_751,                      /* MikroTik RouterBOARD 751 */
        ATH79_MACH_RB_751G,                     /* Mikrotik RouterBOARD 751G */
+       ATH79_MACH_RB_911L,                     /* Mikrotik RouterBOARD 911-2Hn/911-5Hn boards */
        ATH79_MACH_RB_922GS,                    /* Mikrotik RouterBOARD 911/922GS boards */
        ATH79_MACH_RB_941,                      /* MikroTik RouterBOARD 941-2nD */
        ATH79_MACH_RB_951G,                     /* Mikrotik RouterBOARD 951G */
index 403bcb0..f381f85 100644 (file)
@@ -40,7 +40,7 @@ define Device/rb-nor-flash-16M
   LOADER_TYPE := elf
   KERNEL_INSTALL := 1
   KERNEL := kernel-bin | lzma | loader-kernel
-  SUPPORTED_DEVICES := rb-750-r2 rb-750up-r2 rb-750p-pbr2 rb-941-2nd rb-951ui-2nd rb-952ui-5ac2nd rb-962uigs-5hact2hnt rb-lhg-5nd rb-map-2nd rb-mapl-2nd rb-wap-2nd
+  SUPPORTED_DEVICES := rb-750-r2 rb-750up-r2 rb-750p-pbr2 rb-911-2hn rb-911-5hn rb-941-2nd rb-951ui-2nd rb-952ui-5ac2nd rb-962uigs-5hact2hnt rb-lhg-5nd rb-map-2nd rb-mapl-2nd rb-wap-2nd
   IMAGE/sysupgrade.bin := append-kernel | kernel2minor -s 1024 -e | pad-to $$$$(BLOCKSIZE) | \
        append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
 endef
index 625bb19..64c7e88 100644 (file)
@@ -1,6 +1,6 @@
 --- a/arch/mips/ath79/prom.c
 +++ b/arch/mips/ath79/prom.c
-@@ -136,6 +136,30 @@ void __init prom_init(void)
+@@ -136,6 +136,31 @@ void __init prom_init(void)
                initrd_end = initrd_start + fw_getenvl("initrd_size");
        }
  #endif
@@ -26,6 +26,7 @@
 +          strstr(arcs_cmdline, "board=2011L") ||
 +          strstr(arcs_cmdline, "board=2011r") ||
 +          strstr(arcs_cmdline, "board=711Gr100") ||
++          strstr(arcs_cmdline, "board=911L") ||
 +          strstr(arcs_cmdline, "board=922gs"))
 +              ath79_prom_append_cmdline("console", "ttyS0,115200");
  }
index 625bb19..64c7e88 100644 (file)
@@ -1,6 +1,6 @@
 --- a/arch/mips/ath79/prom.c
 +++ b/arch/mips/ath79/prom.c
-@@ -136,6 +136,30 @@ void __init prom_init(void)
+@@ -136,6 +136,31 @@ void __init prom_init(void)
                initrd_end = initrd_start + fw_getenvl("initrd_size");
        }
  #endif
@@ -26,6 +26,7 @@
 +          strstr(arcs_cmdline, "board=2011L") ||
 +          strstr(arcs_cmdline, "board=2011r") ||
 +          strstr(arcs_cmdline, "board=711Gr100") ||
++          strstr(arcs_cmdline, "board=911L") ||
 +          strstr(arcs_cmdline, "board=922gs"))
 +              ath79_prom_append_cmdline("console", "ttyS0,115200");
  }