From: Sergey Ryazanov Date: Tue, 6 Jun 2017 22:49:35 +0000 (+0300) Subject: ath25: add preliminary kernel 4.9 support X-Git-Tag: v18.06.0-rc1~2764 X-Git-Url: http://git.openwrt.org/?p=openwrt%2Fopenwrt.git;a=commitdiff_plain;h=64083848e2e9924c154aef047ae857e67409d5bf ath25: add preliminary kernel 4.9 support Copy and refresh patches and config from 4.4 Signed-off-by: Sergey Ryazanov --- diff --git a/target/linux/ath25/config-4.9 b/target/linux/ath25/config-4.9 new file mode 100644 index 0000000000..de771de519 --- /dev/null +++ b/target/linux/ath25/config-4.9 @@ -0,0 +1,156 @@ +CONFIG_ADM6996_PHY=y +CONFIG_AR2315_WDT=y +CONFIG_AR8216_PHY=y +CONFIG_ARCH_BINFMT_ELF_STATE=y +CONFIG_ARCH_CLOCKSOURCE_DATA=y +CONFIG_ARCH_DISCARD_MEMBLOCK=y +CONFIG_ARCH_HAS_ELF_RANDOMIZE=y +# CONFIG_ARCH_HAS_GCOV_PROFILE_ALL is not set +# CONFIG_ARCH_HAS_SG_CHAIN is not set +CONFIG_ARCH_HIBERNATION_POSSIBLE=y +CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y +CONFIG_ARCH_MIGHT_HAVE_PC_SERIO=y +CONFIG_ARCH_SUPPORTS_UPROBES=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARCH_USE_BUILTIN_BSWAP=y +CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y +CONFIG_ATH25=y +CONFIG_BLK_MQ_PCI=y +CONFIG_CEVT_R4K=y +CONFIG_CLONE_BACKWARDS=y +CONFIG_CMDLINE="console=ttyS0,9600 rootfstype=squashfs,jffs2" +CONFIG_CMDLINE_BOOL=y +# CONFIG_CMDLINE_OVERRIDE is not set +CONFIG_CPU_BIG_ENDIAN=y +CONFIG_CPU_GENERIC_DUMP_TLB=y +CONFIG_CPU_HAS_PREFETCH=y +CONFIG_CPU_HAS_SYNC=y +CONFIG_CPU_MIPS32=y +CONFIG_CPU_MIPS32_R1=y +CONFIG_CPU_MIPSR1=y +CONFIG_CPU_NEEDS_NO_SMARTMIPS_OR_MICROMIPS=y +CONFIG_CPU_R4K_CACHE_TLB=y +CONFIG_CPU_R4K_FPU=y +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_WORKQUEUE=y +CONFIG_CSRC_R4K=y +CONFIG_DMA_NONCOHERENT=y +CONFIG_EARLY_PRINTK=y +CONFIG_ETHERNET_PACKET_MANGLE=y +CONFIG_GENERIC_ATOMIC64=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_IO=y +CONFIG_GENERIC_IRQ_CHIP=y +CONFIG_GENERIC_IRQ_SHOW=y +CONFIG_GENERIC_PCI_IOMAP=y +CONFIG_GENERIC_SCHED_CLOCK=y +CONFIG_GENERIC_SMP_IDLE_THREAD=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GPIOLIB=y +CONFIG_GPIO_AR2315=y +CONFIG_GPIO_AR5312=y +CONFIG_GPIO_SYSFS=y +CONFIG_HANDLE_DOMAIN_IRQ=y +CONFIG_HARDWARE_WATCHPOINTS=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT_MAP=y +# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set +# CONFIG_HAVE_ARCH_BITREVERSE is not set +CONFIG_HAVE_ARCH_JUMP_LABEL=y +CONFIG_HAVE_ARCH_KGDB=y +CONFIG_HAVE_ARCH_SECCOMP_FILTER=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set +CONFIG_HAVE_CBPF_JIT=y +CONFIG_HAVE_CC_STACKPROTECTOR=y +CONFIG_HAVE_CONTEXT_TRACKING=y +CONFIG_HAVE_C_RECORDMCOUNT=y +CONFIG_HAVE_DEBUG_KMEMLEAK=y +CONFIG_HAVE_DEBUG_STACKOVERFLOW=y +CONFIG_HAVE_DMA_API_DEBUG=y +CONFIG_HAVE_DMA_CONTIGUOUS=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y +CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_HAVE_IDE=y +CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_HAVE_MEMBLOCK=y +CONFIG_HAVE_MEMBLOCK_NODE_MAP=y +CONFIG_HAVE_MOD_ARCH_SPECIFIC=y +CONFIG_HAVE_NET_DSA=y +CONFIG_HAVE_OPROFILE=y +CONFIG_HAVE_PERF_EVENTS=y +CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y +CONFIG_HAVE_SYSCALL_TRACEPOINTS=y +CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y +CONFIG_HW_HAS_PCI=y +CONFIG_HW_RANDOM=y +CONFIG_HZ_PERIODIC=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_IP17XX_PHY=y +CONFIG_IRQ_DOMAIN=y +CONFIG_IRQ_FORCED_THREADING=y +CONFIG_IRQ_MIPS_CPU=y +CONFIG_IRQ_WORK=y +CONFIG_LEDS_GPIO=y +CONFIG_MDIO_BOARDINFO=y +CONFIG_MIPS=y +CONFIG_MIPS_ASID_BITS=8 +CONFIG_MIPS_ASID_SHIFT=0 +CONFIG_MIPS_CLOCK_VSYSCALL=y +# CONFIG_MIPS_CMDLINE_BUILTIN_EXTEND is not set +CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER=y +# CONFIG_MIPS_HUGE_TLB_SUPPORT is not set +CONFIG_MIPS_L1_CACHE_SHIFT=5 +# CONFIG_MIPS_MACHINE is not set +CONFIG_MODULES_USE_ELF_REL=y +CONFIG_MTD_AR2315=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +# CONFIG_MTD_CFI_GEOMETRY is not set +# CONFIG_MTD_CFI_INTELEXT is not set +CONFIG_MTD_MYLOADER_PARTS=y +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-3 +CONFIG_MTD_REDBOOT_PARTS=y +CONFIG_MVSWITCH_PHY=y +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_NEED_PER_CPU_KM=y +CONFIG_NET_AR231X=y +CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y +# CONFIG_NO_IOPORT_MAP is not set +# CONFIG_OF is not set +CONFIG_PCI=y +CONFIG_PCI_AR2315=y +CONFIG_PCI_DISABLE_COMMON_QUIRKS=y +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_DRIVERS_LEGACY=y +CONFIG_PERF_USE_VMALLOC=y +CONFIG_PGTABLE_LEVELS=2 +CONFIG_PHYLIB=y +# CONFIG_RCU_STALL_COMMON is not set +CONFIG_SCHED_HRTICK=y +# CONFIG_SCHED_INFO is not set +# CONFIG_SCSI_DMA is not set +# CONFIG_SERIAL_8250_FSL is not set +CONFIG_SERIAL_8250_NR_UARTS=1 +CONFIG_SERIAL_8250_RUNTIME_UARTS=1 +CONFIG_SOC_AR2315=y +CONFIG_SOC_AR5312=y +CONFIG_SRCU=y +# CONFIG_SWAP is not set +CONFIG_SWCONFIG=y +CONFIG_SYSCTL_EXCEPTION_TRACE=y +CONFIG_SYS_HAS_CPU_MIPS32_R1=y +CONFIG_SYS_HAS_EARLY_PRINTK=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_SYS_SUPPORTS_ARBIT_HZ=y +CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y +CONFIG_TICK_CPU_ACCOUNTING=y +CONFIG_USB_SUPPORT=y diff --git a/target/linux/ath25/patches-4.9/107-ar5312_gpio.patch b/target/linux/ath25/patches-4.9/107-ar5312_gpio.patch new file mode 100644 index 0000000000..f4426b52c5 --- /dev/null +++ b/target/linux/ath25/patches-4.9/107-ar5312_gpio.patch @@ -0,0 +1,212 @@ +--- a/arch/mips/ath25/Kconfig ++++ b/arch/mips/ath25/Kconfig +@@ -1,6 +1,7 @@ + config SOC_AR5312 + bool "Atheros AR5312/AR2312+ SoC support" + depends on ATH25 ++ select GPIO_AR5312 + default y + + config SOC_AR2315 +--- a/arch/mips/ath25/ar5312.c ++++ b/arch/mips/ath25/ar5312.c +@@ -22,6 +22,7 @@ + #include + #include + #include ++#include + #include + #include + #include +@@ -180,6 +181,22 @@ static struct platform_device ar5312_phy + .num_resources = 1, + }; + ++static struct resource ar5312_gpio_res[] = { ++ { ++ .name = "ar5312-gpio", ++ .flags = IORESOURCE_MEM, ++ .start = AR5312_GPIO_BASE, ++ .end = AR5312_GPIO_BASE + AR5312_GPIO_SIZE - 1, ++ }, ++}; ++ ++static struct platform_device ar5312_gpio = { ++ .name = "ar5312-gpio", ++ .id = -1, ++ .resource = ar5312_gpio_res, ++ .num_resources = ARRAY_SIZE(ar5312_gpio_res), ++}; ++ + static void __init ar5312_flash_init(void) + { + void __iomem *flashctl_base; +@@ -247,6 +264,8 @@ void __init ar5312_init_devices(void) + + platform_device_register(&ar5312_physmap_flash); + ++ platform_device_register(&ar5312_gpio); ++ + switch (ath25_soc) { + case ATH25_SOC_AR5312: + if (!ath25_board.radio) +--- a/drivers/gpio/Kconfig ++++ b/drivers/gpio/Kconfig +@@ -105,6 +105,13 @@ config GPIO_AMDPT + driver for GPIO functionality on Promontory IOHub + Require ACPI ASL code to enumerate as a platform device. + ++config GPIO_AR5312 ++ bool "AR5312 SoC GPIO support" ++ default y if SOC_AR5312 ++ depends on SOC_AR5312 ++ help ++ Say yes here to enable GPIO support for Atheros AR5312/AR2312+ SoCs. ++ + config GPIO_ASPEED + tristate "Aspeed GPIO support" + depends on (ARCH_ASPEED || COMPILE_TEST) && OF_GPIO +--- a/drivers/gpio/Makefile ++++ b/drivers/gpio/Makefile +@@ -26,6 +26,7 @@ obj-$(CONFIG_GPIO_ADP5588) += gpio-adp55 + obj-$(CONFIG_GPIO_ALTERA) += gpio-altera.o + obj-$(CONFIG_GPIO_AMD8111) += gpio-amd8111.o + obj-$(CONFIG_GPIO_AMDPT) += gpio-amdpt.o ++obj-$(CONFIG_GPIO_AR5312) += gpio-ar5312.o + obj-$(CONFIG_GPIO_ARIZONA) += gpio-arizona.o + obj-$(CONFIG_GPIO_ATH79) += gpio-ath79.o + obj-$(CONFIG_GPIO_ASPEED) += gpio-aspeed.o +--- /dev/null ++++ b/drivers/gpio/gpio-ar5312.c +@@ -0,0 +1,121 @@ ++/* ++ * This file is subject to the terms and conditions of the GNU General Public ++ * License. See the file "COPYING" in the main directory of this archive ++ * for more details. ++ * ++ * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved. ++ * Copyright (C) 2006 FON Technology, SL. ++ * Copyright (C) 2006 Imre Kaloz ++ * Copyright (C) 2006-2009 Felix Fietkau ++ * Copyright (C) 2012 Alexandros C. Couloumbis ++ */ ++ ++#include ++#include ++#include ++#include ++ ++#define DRIVER_NAME "ar5312-gpio" ++ ++#define AR5312_GPIO_DO 0x00 /* output register */ ++#define AR5312_GPIO_DI 0x04 /* intput register */ ++#define AR5312_GPIO_CR 0x08 /* control register */ ++ ++#define AR5312_GPIO_CR_M(x) (1 << (x)) /* mask for i/o */ ++#define AR5312_GPIO_CR_O(x) (0 << (x)) /* mask for output */ ++#define AR5312_GPIO_CR_I(x) (1 << (x)) /* mask for input */ ++#define AR5312_GPIO_CR_INT(x) (1 << ((x)+8)) /* mask for interrupt */ ++#define AR5312_GPIO_CR_UART(x) (1 << ((x)+16)) /* uart multiplex */ ++ ++#define AR5312_GPIO_NUM 8 ++ ++static void __iomem *ar5312_mem; ++ ++static inline u32 ar5312_gpio_reg_read(unsigned reg) ++{ ++ return __raw_readl(ar5312_mem + reg); ++} ++ ++static inline void ar5312_gpio_reg_write(unsigned reg, u32 val) ++{ ++ __raw_writel(val, ar5312_mem + reg); ++} ++ ++static inline void ar5312_gpio_reg_mask(unsigned reg, u32 mask, u32 val) ++{ ++ ar5312_gpio_reg_write(reg, (ar5312_gpio_reg_read(reg) & ~mask) | val); ++} ++ ++static int ar5312_gpio_get_val(struct gpio_chip *chip, unsigned gpio) ++{ ++ return (ar5312_gpio_reg_read(AR5312_GPIO_DI) >> gpio) & 1; ++} ++ ++static void ar5312_gpio_set_val(struct gpio_chip *chip, unsigned gpio, int val) ++{ ++ u32 reg = ar5312_gpio_reg_read(AR5312_GPIO_DO); ++ ++ reg = val ? reg | (1 << gpio) : reg & ~(1 << gpio); ++ ar5312_gpio_reg_write(AR5312_GPIO_DO, reg); ++} ++ ++static int ar5312_gpio_dir_in(struct gpio_chip *chip, unsigned gpio) ++{ ++ ar5312_gpio_reg_mask(AR5312_GPIO_CR, 0, 1 << gpio); ++ return 0; ++} ++ ++static int ar5312_gpio_dir_out(struct gpio_chip *chip, unsigned gpio, int val) ++{ ++ ar5312_gpio_reg_mask(AR5312_GPIO_CR, 1 << gpio, 0); ++ ar5312_gpio_set_val(chip, gpio, val); ++ return 0; ++} ++ ++static struct gpio_chip ar5312_gpio_chip = { ++ .label = DRIVER_NAME, ++ .direction_input = ar5312_gpio_dir_in, ++ .direction_output = ar5312_gpio_dir_out, ++ .set = ar5312_gpio_set_val, ++ .get = ar5312_gpio_get_val, ++ .base = 0, ++ .ngpio = AR5312_GPIO_NUM, ++}; ++ ++static int ar5312_gpio_probe(struct platform_device *pdev) ++{ ++ struct device *dev = &pdev->dev; ++ struct resource *res; ++ int ret; ++ ++ if (ar5312_mem) ++ return -EBUSY; ++ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ ar5312_mem = devm_ioremap_resource(dev, res); ++ if (IS_ERR(ar5312_mem)) ++ return PTR_ERR(ar5312_mem); ++ ++ ar5312_gpio_chip.dev = dev; ++ ret = gpiochip_add(&ar5312_gpio_chip); ++ if (ret) { ++ dev_err(dev, "failed to add gpiochip\n"); ++ return ret; ++ } ++ ++ return 0; ++} ++ ++static struct platform_driver ar5312_gpio_driver = { ++ .probe = ar5312_gpio_probe, ++ .driver = { ++ .name = DRIVER_NAME, ++ .owner = THIS_MODULE, ++ } ++}; ++ ++static int __init ar5312_gpio_init(void) ++{ ++ return platform_driver_register(&ar5312_gpio_driver); ++} ++subsys_initcall(ar5312_gpio_init); +--- a/arch/mips/Kconfig ++++ b/arch/mips/Kconfig +@@ -167,6 +167,7 @@ config ATH25 + select CEVT_R4K + select CSRC_R4K + select DMA_NONCOHERENT ++ select GPIOLIB + select IRQ_MIPS_CPU + select IRQ_DOMAIN + select SYS_HAS_CPU_MIPS32_R1 diff --git a/target/linux/ath25/patches-4.9/108-ar2315_gpio.patch b/target/linux/ath25/patches-4.9/108-ar2315_gpio.patch new file mode 100644 index 0000000000..6bb793d98c --- /dev/null +++ b/target/linux/ath25/patches-4.9/108-ar2315_gpio.patch @@ -0,0 +1,363 @@ +--- a/arch/mips/ath25/Kconfig ++++ b/arch/mips/ath25/Kconfig +@@ -7,6 +7,7 @@ config SOC_AR5312 + config SOC_AR2315 + bool "Atheros AR2315+ SoC support" + depends on ATH25 ++ select GPIO_AR2315 + default y + + config PCI_AR2315 +--- a/arch/mips/ath25/ar2315.c ++++ b/arch/mips/ath25/ar2315.c +@@ -21,6 +21,8 @@ + #include + #include + #include ++#include ++#include + #include + #include + #include +@@ -167,11 +169,42 @@ void __init ar2315_arch_init_irq(void) + ar2315_misc_irq_domain = domain; + } + ++static struct resource ar2315_gpio_res[] = { ++ { ++ .name = "ar2315-gpio", ++ .flags = IORESOURCE_MEM, ++ .start = AR2315_RST_BASE + AR2315_GPIO, ++ .end = AR2315_RST_BASE + AR2315_GPIO + 0x10 - 1, ++ }, ++ { ++ .name = "ar2315-gpio", ++ .flags = IORESOURCE_IRQ, ++ }, ++ { ++ .name = "ar2315-gpio-irq-base", ++ .flags = IORESOURCE_IRQ, ++ .start = AR231X_GPIO_IRQ_BASE, ++ .end = AR231X_GPIO_IRQ_BASE, ++ } ++}; ++ ++static struct platform_device ar2315_gpio = { ++ .id = -1, ++ .name = "ar2315-gpio", ++ .resource = ar2315_gpio_res, ++ .num_resources = ARRAY_SIZE(ar2315_gpio_res) ++}; ++ + void __init ar2315_init_devices(void) + { + /* Find board configuration */ + ath25_find_config(AR2315_SPI_READ_BASE, AR2315_SPI_READ_SIZE); + ++ ar2315_gpio_res[1].start = irq_create_mapping(ar2315_misc_irq_domain, ++ AR2315_MISC_IRQ_GPIO); ++ ar2315_gpio_res[1].end = ar2315_gpio_res[1].start; ++ platform_device_register(&ar2315_gpio); ++ + ath25_add_wmac(0, AR2315_WLAN0_BASE, AR2315_IRQ_WLAN0); + } + +@@ -187,8 +220,8 @@ static void ar2315_restart(char *command + /* Cold reset does not work on the AR2315/6, use the GPIO reset bits + * a workaround. Give it some time to attempt a gpio based hardware + * reset (atheros reference design workaround) */ +- +- /* TODO: implement the GPIO reset workaround */ ++ gpio_request_one(AR2315_RESET_GPIO, GPIOF_OUT_INIT_LOW, "Reset"); ++ mdelay(100); + + /* Some boards (e.g. Senao EOC-2610) don't implement the reset logic + * workaround. Attempt to jump to the mips reset location - +--- a/drivers/gpio/Kconfig ++++ b/drivers/gpio/Kconfig +@@ -105,6 +105,13 @@ config GPIO_AMDPT + driver for GPIO functionality on Promontory IOHub + Require ACPI ASL code to enumerate as a platform device. + ++config GPIO_AR2315 ++ bool "AR2315 SoC GPIO support" ++ default y if SOC_AR2315 ++ depends on SOC_AR2315 ++ help ++ Say yes here to enable GPIO support for Atheros AR2315+ SoCs. ++ + config GPIO_AR5312 + bool "AR5312 SoC GPIO support" + default y if SOC_AR5312 +--- a/drivers/gpio/Makefile ++++ b/drivers/gpio/Makefile +@@ -26,6 +26,7 @@ obj-$(CONFIG_GPIO_ADP5588) += gpio-adp55 + obj-$(CONFIG_GPIO_ALTERA) += gpio-altera.o + obj-$(CONFIG_GPIO_AMD8111) += gpio-amd8111.o + obj-$(CONFIG_GPIO_AMDPT) += gpio-amdpt.o ++obj-$(CONFIG_GPIO_AR2315) += gpio-ar2315.o + obj-$(CONFIG_GPIO_AR5312) += gpio-ar5312.o + obj-$(CONFIG_GPIO_ARIZONA) += gpio-arizona.o + obj-$(CONFIG_GPIO_ATH79) += gpio-ath79.o +--- /dev/null ++++ b/drivers/gpio/gpio-ar2315.c +@@ -0,0 +1,233 @@ ++/* ++ * This file is subject to the terms and conditions of the GNU General Public ++ * License. See the file "COPYING" in the main directory of this archive ++ * for more details. ++ * ++ * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved. ++ * Copyright (C) 2006 FON Technology, SL. ++ * Copyright (C) 2006 Imre Kaloz ++ * Copyright (C) 2006 Felix Fietkau ++ * Copyright (C) 2012 Alexandros C. Couloumbis ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++ ++#define DRIVER_NAME "ar2315-gpio" ++ ++#define AR2315_GPIO_DI 0x0000 ++#define AR2315_GPIO_DO 0x0008 ++#define AR2315_GPIO_DIR 0x0010 ++#define AR2315_GPIO_INT 0x0018 ++ ++#define AR2315_GPIO_DIR_M(x) (1 << (x)) /* mask for i/o */ ++#define AR2315_GPIO_DIR_O(x) (1 << (x)) /* output */ ++#define AR2315_GPIO_DIR_I(x) (0) /* input */ ++ ++#define AR2315_GPIO_INT_NUM_M 0x3F /* mask for GPIO num */ ++#define AR2315_GPIO_INT_TRIG(x) ((x) << 6) /* interrupt trigger */ ++#define AR2315_GPIO_INT_TRIG_M (0x3 << 6) /* mask for int trig */ ++ ++#define AR2315_GPIO_INT_TRIG_OFF 0 /* Triggerring off */ ++#define AR2315_GPIO_INT_TRIG_LOW 1 /* Low Level Triggered */ ++#define AR2315_GPIO_INT_TRIG_HIGH 2 /* High Level Triggered */ ++#define AR2315_GPIO_INT_TRIG_EDGE 3 /* Edge Triggered */ ++ ++#define AR2315_GPIO_NUM 22 ++ ++static u32 ar2315_gpio_intmask; ++static u32 ar2315_gpio_intval; ++static unsigned ar2315_gpio_irq_base; ++static void __iomem *ar2315_mem; ++ ++static inline u32 ar2315_gpio_reg_read(unsigned reg) ++{ ++ return __raw_readl(ar2315_mem + reg); ++} ++ ++static inline void ar2315_gpio_reg_write(unsigned reg, u32 val) ++{ ++ __raw_writel(val, ar2315_mem + reg); ++} ++ ++static inline void ar2315_gpio_reg_mask(unsigned reg, u32 mask, u32 val) ++{ ++ ar2315_gpio_reg_write(reg, (ar2315_gpio_reg_read(reg) & ~mask) | val); ++} ++ ++static void ar2315_gpio_irq_handler(struct irq_desc *desc) ++{ ++ u32 pend; ++ int bit = -1; ++ ++ /* only do one gpio interrupt at a time */ ++ pend = ar2315_gpio_reg_read(AR2315_GPIO_DI); ++ pend ^= ar2315_gpio_intval; ++ pend &= ar2315_gpio_intmask; ++ ++ if (pend) { ++ bit = fls(pend) - 1; ++ pend &= ~(1 << bit); ++ ar2315_gpio_intval ^= (1 << bit); ++ } ++ ++ /* Enable interrupt with edge detection */ ++ if ((ar2315_gpio_reg_read(AR2315_GPIO_DIR) & AR2315_GPIO_DIR_M(bit)) != ++ AR2315_GPIO_DIR_I(bit)) ++ return; ++ ++ if (bit >= 0) ++ generic_handle_irq(ar2315_gpio_irq_base + bit); ++} ++ ++static void ar2315_gpio_int_setup(unsigned gpio, int trig) ++{ ++ u32 reg = ar2315_gpio_reg_read(AR2315_GPIO_INT); ++ ++ reg &= ~(AR2315_GPIO_INT_NUM_M | AR2315_GPIO_INT_TRIG_M); ++ reg |= gpio | AR2315_GPIO_INT_TRIG(trig); ++ ar2315_gpio_reg_write(AR2315_GPIO_INT, reg); ++} ++ ++static void ar2315_gpio_irq_unmask(struct irq_data *d) ++{ ++ unsigned gpio = d->irq - ar2315_gpio_irq_base; ++ u32 dir = ar2315_gpio_reg_read(AR2315_GPIO_DIR); ++ ++ /* Enable interrupt with edge detection */ ++ if ((dir & AR2315_GPIO_DIR_M(gpio)) != AR2315_GPIO_DIR_I(gpio)) ++ return; ++ ++ ar2315_gpio_intmask |= (1 << gpio); ++ ar2315_gpio_int_setup(gpio, AR2315_GPIO_INT_TRIG_EDGE); ++} ++ ++static void ar2315_gpio_irq_mask(struct irq_data *d) ++{ ++ unsigned gpio = d->irq - ar2315_gpio_irq_base; ++ ++ /* Disable interrupt */ ++ ar2315_gpio_intmask &= ~(1 << gpio); ++ ar2315_gpio_int_setup(gpio, AR2315_GPIO_INT_TRIG_OFF); ++} ++ ++static struct irq_chip ar2315_gpio_irq_chip = { ++ .name = DRIVER_NAME, ++ .irq_unmask = ar2315_gpio_irq_unmask, ++ .irq_mask = ar2315_gpio_irq_mask, ++}; ++ ++static void ar2315_gpio_irq_init(unsigned irq) ++{ ++ unsigned i; ++ ++ ar2315_gpio_intval = ar2315_gpio_reg_read(AR2315_GPIO_DI); ++ for (i = 0; i < AR2315_GPIO_NUM; i++) { ++ unsigned _irq = ar2315_gpio_irq_base + i; ++ ++ irq_set_chip_and_handler(_irq, &ar2315_gpio_irq_chip, ++ handle_level_irq); ++ } ++ irq_set_chained_handler(irq, ar2315_gpio_irq_handler); ++} ++ ++static int ar2315_gpio_get_val(struct gpio_chip *chip, unsigned gpio) ++{ ++ return (ar2315_gpio_reg_read(AR2315_GPIO_DI) >> gpio) & 1; ++} ++ ++static void ar2315_gpio_set_val(struct gpio_chip *chip, unsigned gpio, int val) ++{ ++ u32 reg = ar2315_gpio_reg_read(AR2315_GPIO_DO); ++ ++ reg = val ? reg | (1 << gpio) : reg & ~(1 << gpio); ++ ar2315_gpio_reg_write(AR2315_GPIO_DO, reg); ++} ++ ++static int ar2315_gpio_dir_in(struct gpio_chip *chip, unsigned gpio) ++{ ++ ar2315_gpio_reg_mask(AR2315_GPIO_DIR, 1 << gpio, 0); ++ return 0; ++} ++ ++static int ar2315_gpio_dir_out(struct gpio_chip *chip, unsigned gpio, int val) ++{ ++ ar2315_gpio_reg_mask(AR2315_GPIO_DIR, 0, 1 << gpio); ++ ar2315_gpio_set_val(chip, gpio, val); ++ return 0; ++} ++ ++static int ar2315_gpio_to_irq(struct gpio_chip *chip, unsigned gpio) ++{ ++ return ar2315_gpio_irq_base + gpio; ++} ++ ++static struct gpio_chip ar2315_gpio_chip = { ++ .label = DRIVER_NAME, ++ .direction_input = ar2315_gpio_dir_in, ++ .direction_output = ar2315_gpio_dir_out, ++ .set = ar2315_gpio_set_val, ++ .get = ar2315_gpio_get_val, ++ .to_irq = ar2315_gpio_to_irq, ++ .base = 0, ++ .ngpio = AR2315_GPIO_NUM, ++}; ++ ++static int ar2315_gpio_probe(struct platform_device *pdev) ++{ ++ struct device *dev = &pdev->dev; ++ struct resource *res; ++ unsigned irq; ++ int ret; ++ ++ if (ar2315_mem) ++ return -EBUSY; ++ ++ res = platform_get_resource_byname(pdev, IORESOURCE_IRQ, ++ "ar2315-gpio-irq-base"); ++ if (!res) { ++ dev_err(dev, "not found GPIO IRQ base\n"); ++ return -ENXIO; ++ } ++ ar2315_gpio_irq_base = res->start; ++ ++ res = platform_get_resource_byname(pdev, IORESOURCE_IRQ, DRIVER_NAME); ++ if (!res) { ++ dev_err(dev, "not found IRQ number\n"); ++ return -ENXIO; ++ } ++ irq = res->start; ++ ++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, DRIVER_NAME); ++ ar2315_mem = devm_ioremap_resource(dev, res); ++ if (IS_ERR(ar2315_mem)) ++ return PTR_ERR(ar2315_mem); ++ ++ ar2315_gpio_chip.dev = dev; ++ ret = gpiochip_add(&ar2315_gpio_chip); ++ if (ret) { ++ dev_err(dev, "failed to add gpiochip\n"); ++ return ret; ++ } ++ ++ ar2315_gpio_irq_init(irq); ++ ++ return 0; ++} ++ ++static struct platform_driver ar2315_gpio_driver = { ++ .probe = ar2315_gpio_probe, ++ .driver = { ++ .name = DRIVER_NAME, ++ .owner = THIS_MODULE, ++ } ++}; ++ ++static int __init ar2315_gpio_init(void) ++{ ++ return platform_driver_register(&ar2315_gpio_driver); ++} ++subsys_initcall(ar2315_gpio_init); +--- a/arch/mips/ath25/devices.h ++++ b/arch/mips/ath25/devices.h +@@ -3,6 +3,11 @@ + + #include + ++#define AR231X_GPIO_IRQ_BASE 0x30 ++ ++/* GPIO number for AR2315/16 reset issue workaround */ ++#define AR2315_RESET_GPIO 5 ++ + #define ATH25_REG_MS(_val, _field) (((_val) & _field##_M) >> _field##_S) + + #define ATH25_IRQ_CPU_CLOCK (MIPS_CPU_IRQ_BASE + 7) /* C0_CAUSE: 0x8000 */ +--- a/arch/mips/ath25/ar2315_regs.h ++++ b/arch/mips/ath25/ar2315_regs.h +@@ -315,6 +315,9 @@ + #define AR2315_MEM_CFG_BANKADDR_BITS_M 0x00000018 + #define AR2315_MEM_CFG_BANKADDR_BITS_S 3 + ++/* GPIO MMR base address */ ++#define AR2315_GPIO 0x0088 ++ + /* + * Local Bus Interface Registers + */ diff --git a/target/linux/ath25/patches-4.9/110-ar2313_ethernet.patch b/target/linux/ath25/patches-4.9/110-ar2313_ethernet.patch new file mode 100644 index 0000000000..9b1286c075 --- /dev/null +++ b/target/linux/ath25/patches-4.9/110-ar2313_ethernet.patch @@ -0,0 +1,1828 @@ +--- a/drivers/net/ethernet/atheros/Makefile ++++ b/drivers/net/ethernet/atheros/Makefile +@@ -7,3 +7,4 @@ obj-$(CONFIG_ATL2) += atlx/ + obj-$(CONFIG_ATL1E) += atl1e/ + obj-$(CONFIG_ATL1C) += atl1c/ + obj-$(CONFIG_ALX) += alx/ ++obj-$(CONFIG_NET_AR231X) += ar231x/ +--- a/drivers/net/ethernet/atheros/Kconfig ++++ b/drivers/net/ethernet/atheros/Kconfig +@@ -5,7 +5,7 @@ + config NET_VENDOR_ATHEROS + bool "Atheros devices" + default y +- depends on PCI ++ depends on (PCI || ATH25) + ---help--- + If you have a network (Ethernet) card belonging to this class, say Y. + +@@ -78,4 +78,10 @@ config ALX + To compile this driver as a module, choose M here. The module + will be called alx. + ++config NET_AR231X ++ tristate "Atheros AR231X built-in Ethernet support" ++ depends on ATH25 ++ help ++ Support for the AR231x/531x ethernet controller ++ + endif # NET_VENDOR_ATHEROS +--- /dev/null ++++ b/drivers/net/ethernet/atheros/ar231x/Makefile +@@ -0,0 +1 @@ ++obj-$(CONFIG_NET_AR231X) += ar231x.o +--- /dev/null ++++ b/drivers/net/ethernet/atheros/ar231x/ar231x.c +@@ -0,0 +1,1206 @@ ++/* ++ * ar231x.c: Linux driver for the Atheros AR231x Ethernet device. ++ * ++ * Copyright (C) 2004 by Sameer Dekate ++ * Copyright (C) 2006 Imre Kaloz ++ * Copyright (C) 2006-2009 Felix Fietkau ++ * ++ * Thanks to Atheros for providing hardware and documentation ++ * enabling me to write this driver. ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License as published by ++ * the Free Software Foundation; either version 2 of the License, or ++ * (at your option) any later version. ++ * ++ * Additional credits: ++ * This code is taken from John Taylor's Sibyte driver and then ++ * modified for the AR2313. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define AR2313_MTU 1692 ++#define AR2313_PRIOS 1 ++#define AR2313_QUEUES (2*AR2313_PRIOS) ++#define AR2313_DESCR_ENTRIES 64 ++ ++#ifndef min ++#define min(a, b) (((a) < (b)) ? (a) : (b)) ++#endif ++ ++#ifndef SMP_CACHE_BYTES ++#define SMP_CACHE_BYTES L1_CACHE_BYTES ++#endif ++ ++#define AR2313_MBOX_SET_BIT 0x8 ++ ++#include "ar231x.h" ++ ++/** ++ * New interrupt handler strategy: ++ * ++ * An old interrupt handler worked using the traditional method of ++ * replacing an skbuff with a new one when a packet arrives. However ++ * the rx rings do not need to contain a static number of buffer ++ * descriptors, thus it makes sense to move the memory allocation out ++ * of the main interrupt handler and do it in a bottom half handler ++ * and only allocate new buffers when the number of buffers in the ++ * ring is below a certain threshold. In order to avoid starving the ++ * NIC under heavy load it is however necessary to force allocation ++ * when hitting a minimum threshold. The strategy for alloction is as ++ * follows: ++ * ++ * RX_LOW_BUF_THRES - allocate buffers in the bottom half ++ * RX_PANIC_LOW_THRES - we are very low on buffers, allocate ++ * the buffers in the interrupt handler ++ * RX_RING_THRES - maximum number of buffers in the rx ring ++ * ++ * One advantagous side effect of this allocation approach is that the ++ * entire rx processing can be done without holding any spin lock ++ * since the rx rings and registers are totally independent of the tx ++ * ring and its registers. This of course includes the kmalloc's of ++ * new skb's. Thus start_xmit can run in parallel with rx processing ++ * and the memory allocation on SMP systems. ++ * ++ * Note that running the skb reallocation in a bottom half opens up ++ * another can of races which needs to be handled properly. In ++ * particular it can happen that the interrupt handler tries to run ++ * the reallocation while the bottom half is either running on another ++ * CPU or was interrupted on the same CPU. To get around this the ++ * driver uses bitops to prevent the reallocation routines from being ++ * reentered. ++ * ++ * TX handling can also be done without holding any spin lock, wheee ++ * this is fun! since tx_csm is only written to by the interrupt ++ * handler. ++ */ ++ ++/** ++ * Threshold values for RX buffer allocation - the low water marks for ++ * when to start refilling the rings are set to 75% of the ring ++ * sizes. It seems to make sense to refill the rings entirely from the ++ * intrrupt handler once it gets below the panic threshold, that way ++ * we don't risk that the refilling is moved to another CPU when the ++ * one running the interrupt handler just got the slab code hot in its ++ * cache. ++ */ ++#define RX_RING_SIZE AR2313_DESCR_ENTRIES ++#define RX_PANIC_THRES (RX_RING_SIZE/4) ++#define RX_LOW_THRES ((3*RX_RING_SIZE)/4) ++#define CRC_LEN 4 ++#define RX_OFFSET 2 ++ ++#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE) ++#define VLAN_HDR 4 ++#else ++#define VLAN_HDR 0 ++#endif ++ ++#define AR2313_BUFSIZE (AR2313_MTU + VLAN_HDR + ETH_HLEN + CRC_LEN + \ ++ RX_OFFSET) ++ ++#ifdef MODULE ++MODULE_LICENSE("GPL"); ++MODULE_AUTHOR("Sameer Dekate , Imre Kaloz , Felix Fietkau "); ++MODULE_DESCRIPTION("AR231x Ethernet driver"); ++#endif ++ ++#define virt_to_phys(x) ((u32)(x) & 0x1fffffff) ++ ++/* prototypes */ ++static void ar231x_halt(struct net_device *dev); ++static void rx_tasklet_func(unsigned long data); ++static void rx_tasklet_cleanup(struct net_device *dev); ++static void ar231x_multicast_list(struct net_device *dev); ++static void ar231x_tx_timeout(struct net_device *dev); ++ ++static int ar231x_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum); ++static int ar231x_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum, ++ u16 value); ++static int ar231x_mdiobus_reset(struct mii_bus *bus); ++static int ar231x_mdiobus_probe(struct net_device *dev); ++static void ar231x_adjust_link(struct net_device *dev); ++ ++#ifndef ERR ++#define ERR(fmt, args...) printk("%s: " fmt, __func__, ##args) ++#endif ++ ++#ifdef CONFIG_NET_POLL_CONTROLLER ++static void ++ar231x_netpoll(struct net_device *dev) ++{ ++ unsigned long flags; ++ ++ local_irq_save(flags); ++ ar231x_interrupt(dev->irq, dev); ++ local_irq_restore(flags); ++} ++#endif ++ ++static const struct net_device_ops ar231x_ops = { ++ .ndo_open = ar231x_open, ++ .ndo_stop = ar231x_close, ++ .ndo_start_xmit = ar231x_start_xmit, ++ .ndo_set_rx_mode = ar231x_multicast_list, ++ .ndo_do_ioctl = ar231x_ioctl, ++ .ndo_change_mtu = eth_change_mtu, ++ .ndo_validate_addr = eth_validate_addr, ++ .ndo_set_mac_address = eth_mac_addr, ++ .ndo_tx_timeout = ar231x_tx_timeout, ++#ifdef CONFIG_NET_POLL_CONTROLLER ++ .ndo_poll_controller = ar231x_netpoll, ++#endif ++}; ++ ++static int ar231x_probe(struct platform_device *pdev) ++{ ++ struct net_device *dev; ++ struct ar231x_private *sp; ++ struct resource *res; ++ unsigned long ar_eth_base; ++ char buf[64]; ++ ++ dev = alloc_etherdev(sizeof(struct ar231x_private)); ++ ++ if (dev == NULL) { ++ printk(KERN_ERR ++ "ar231x: Unable to allocate net_device structure!\n"); ++ return -ENOMEM; ++ } ++ ++ platform_set_drvdata(pdev, dev); ++ ++ sp = netdev_priv(dev); ++ sp->dev = dev; ++ sp->cfg = pdev->dev.platform_data; ++ ++ sprintf(buf, "eth%d_membase", pdev->id); ++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, buf); ++ if (!res) ++ return -ENODEV; ++ ++ sp->link = 0; ++ ar_eth_base = res->start; ++ ++ sprintf(buf, "eth%d_irq", pdev->id); ++ dev->irq = platform_get_irq_byname(pdev, buf); ++ ++ spin_lock_init(&sp->lock); ++ ++ dev->features |= NETIF_F_HIGHDMA; ++ dev->netdev_ops = &ar231x_ops; ++ ++ tasklet_init(&sp->rx_tasklet, rx_tasklet_func, (unsigned long)dev); ++ tasklet_disable(&sp->rx_tasklet); ++ ++ sp->eth_regs = ioremap_nocache(ar_eth_base, sizeof(*sp->eth_regs)); ++ if (!sp->eth_regs) { ++ printk("Can't remap eth registers\n"); ++ return -ENXIO; ++ } ++ ++ /** ++ * When there's only one MAC, PHY regs are typically on ENET0, ++ * even though the MAC might be on ENET1. ++ * So remap PHY regs separately. ++ */ ++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "eth0_mii"); ++ if (!res) { ++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, ++ "eth1_mii"); ++ if (!res) ++ return -ENODEV; ++ } ++ sp->phy_regs = ioremap_nocache(res->start, resource_size(res)); ++ if (!sp->phy_regs) { ++ printk("Can't remap phy registers\n"); ++ return -ENXIO; ++ } ++ ++ sp->dma_regs = ioremap_nocache(ar_eth_base + 0x1000, ++ sizeof(*sp->dma_regs)); ++ if (!sp->dma_regs) { ++ printk("Can't remap DMA registers\n"); ++ return -ENXIO; ++ } ++ dev->base_addr = ar_eth_base + 0x1000; ++ ++ strncpy(sp->name, "Atheros AR231x", sizeof(sp->name) - 1); ++ sp->name[sizeof(sp->name) - 1] = '\0'; ++ memcpy(dev->dev_addr, sp->cfg->macaddr, 6); ++ ++ if (ar231x_init(dev)) { ++ /* ar231x_init() calls ar231x_init_cleanup() on error */ ++ kfree(dev); ++ return -ENODEV; ++ } ++ ++ if (register_netdev(dev)) { ++ printk("%s: register_netdev failed\n", __func__); ++ return -1; ++ } ++ ++ printk("%s: %s: %pM, irq %d\n", dev->name, sp->name, dev->dev_addr, ++ dev->irq); ++ ++ sp->mii_bus = mdiobus_alloc(); ++ if (sp->mii_bus == NULL) ++ return -1; ++ ++ sp->mii_bus->priv = dev; ++ sp->mii_bus->read = ar231x_mdiobus_read; ++ sp->mii_bus->write = ar231x_mdiobus_write; ++ sp->mii_bus->reset = ar231x_mdiobus_reset; ++ sp->mii_bus->name = "ar231x_eth_mii"; ++ snprintf(sp->mii_bus->id, MII_BUS_ID_SIZE, "%d", pdev->id); ++ sp->mii_bus->irq = kmalloc(sizeof(int), GFP_KERNEL); ++ *sp->mii_bus->irq = PHY_POLL; ++ ++ mdiobus_register(sp->mii_bus); ++ ++ if (ar231x_mdiobus_probe(dev) != 0) { ++ printk(KERN_ERR "%s: mdiobus_probe failed\n", dev->name); ++ rx_tasklet_cleanup(dev); ++ ar231x_init_cleanup(dev); ++ unregister_netdev(dev); ++ kfree(dev); ++ return -ENODEV; ++ } ++ ++ /* start link poll timer */ ++ ar231x_setup_timer(dev); ++ ++ return 0; ++} ++ ++static void ar231x_multicast_list(struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ unsigned int filter; ++ ++ filter = sp->eth_regs->mac_control; ++ ++ if (dev->flags & IFF_PROMISC) ++ filter |= MAC_CONTROL_PR; ++ else ++ filter &= ~MAC_CONTROL_PR; ++ if ((dev->flags & IFF_ALLMULTI) || (netdev_mc_count(dev) > 0)) ++ filter |= MAC_CONTROL_PM; ++ else ++ filter &= ~MAC_CONTROL_PM; ++ ++ sp->eth_regs->mac_control = filter; ++} ++ ++static void rx_tasklet_cleanup(struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ ++ /** ++ * Tasklet may be scheduled. Need to get it removed from the list ++ * since we're about to free the struct. ++ */ ++ ++ sp->unloading = 1; ++ tasklet_enable(&sp->rx_tasklet); ++ tasklet_kill(&sp->rx_tasklet); ++} ++ ++static int ar231x_remove(struct platform_device *pdev) ++{ ++ struct net_device *dev = platform_get_drvdata(pdev); ++ struct ar231x_private *sp = netdev_priv(dev); ++ ++ rx_tasklet_cleanup(dev); ++ ar231x_init_cleanup(dev); ++ unregister_netdev(dev); ++ mdiobus_unregister(sp->mii_bus); ++ mdiobus_free(sp->mii_bus); ++ kfree(dev); ++ return 0; ++} ++ ++/** ++ * Restart the AR2313 ethernet controller. ++ */ ++static int ar231x_restart(struct net_device *dev) ++{ ++ /* disable interrupts */ ++ disable_irq(dev->irq); ++ ++ /* stop mac */ ++ ar231x_halt(dev); ++ ++ /* initialize */ ++ ar231x_init(dev); ++ ++ /* enable interrupts */ ++ enable_irq(dev->irq); ++ ++ return 0; ++} ++ ++static struct platform_driver ar231x_driver = { ++ .driver.name = "ar231x-eth", ++ .probe = ar231x_probe, ++ .remove = ar231x_remove, ++}; ++ ++module_platform_driver(ar231x_driver); ++ ++static void ar231x_free_descriptors(struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ ++ if (sp->rx_ring != NULL) { ++ kfree((void *)KSEG0ADDR(sp->rx_ring)); ++ sp->rx_ring = NULL; ++ sp->tx_ring = NULL; ++ } ++} ++ ++static int ar231x_allocate_descriptors(struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ int size; ++ int j; ++ ar231x_descr_t *space; ++ ++ if (sp->rx_ring != NULL) { ++ printk("%s: already done.\n", __func__); ++ return 0; ++ } ++ ++ size = sizeof(ar231x_descr_t) * (AR2313_DESCR_ENTRIES * AR2313_QUEUES); ++ space = kmalloc(size, GFP_KERNEL); ++ if (space == NULL) ++ return 1; ++ ++ /* invalidate caches */ ++ dma_cache_inv((unsigned int)space, size); ++ ++ /* now convert pointer to KSEG1 */ ++ space = (ar231x_descr_t *)KSEG1ADDR(space); ++ ++ memset((void *)space, 0, size); ++ ++ sp->rx_ring = space; ++ space += AR2313_DESCR_ENTRIES; ++ ++ sp->tx_ring = space; ++ space += AR2313_DESCR_ENTRIES; ++ ++ /* Initialize the transmit Descriptors */ ++ for (j = 0; j < AR2313_DESCR_ENTRIES; j++) { ++ ar231x_descr_t *td = &sp->tx_ring[j]; ++ ++ td->status = 0; ++ td->devcs = DMA_TX1_CHAINED; ++ td->addr = 0; ++ td->descr = virt_to_phys(&sp->tx_ring[DSC_NEXT(j)]); ++ } ++ ++ return 0; ++} ++ ++/** ++ * Generic cleanup handling data allocated during init. Used when the ++ * module is unloaded or if an error occurs during initialization ++ */ ++static void ar231x_init_cleanup(struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ struct sk_buff *skb; ++ int j; ++ ++ ar231x_free_descriptors(dev); ++ ++ if (sp->eth_regs) ++ iounmap((void *)sp->eth_regs); ++ if (sp->dma_regs) ++ iounmap((void *)sp->dma_regs); ++ if (sp->phy_regs) ++ iounmap((void *)sp->phy_regs); ++ ++ if (sp->rx_skb) { ++ for (j = 0; j < AR2313_DESCR_ENTRIES; j++) { ++ skb = sp->rx_skb[j]; ++ if (skb) { ++ sp->rx_skb[j] = NULL; ++ dev_kfree_skb(skb); ++ } ++ } ++ kfree(sp->rx_skb); ++ sp->rx_skb = NULL; ++ } ++ ++ if (sp->tx_skb) { ++ for (j = 0; j < AR2313_DESCR_ENTRIES; j++) { ++ skb = sp->tx_skb[j]; ++ if (skb) { ++ sp->tx_skb[j] = NULL; ++ dev_kfree_skb(skb); ++ } ++ } ++ kfree(sp->tx_skb); ++ sp->tx_skb = NULL; ++ } ++} ++ ++static int ar231x_setup_timer(struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ ++ init_timer(&sp->link_timer); ++ ++ sp->link_timer.function = ar231x_link_timer_fn; ++ sp->link_timer.data = (int)dev; ++ sp->link_timer.expires = jiffies + HZ; ++ ++ add_timer(&sp->link_timer); ++ return 0; ++} ++ ++static void ar231x_link_timer_fn(unsigned long data) ++{ ++ struct net_device *dev = (struct net_device *)data; ++ struct ar231x_private *sp = netdev_priv(dev); ++ ++ /** ++ * See if the link status changed. ++ * This was needed to make sure we set the PHY to the ++ * autonegotiated value of half or full duplex. ++ */ ++ ar231x_check_link(dev); ++ ++ /** ++ * Loop faster when we don't have link. ++ * This was needed to speed up the AP bootstrap time. ++ */ ++ if (sp->link == 0) ++ mod_timer(&sp->link_timer, jiffies + HZ / 2); ++ else ++ mod_timer(&sp->link_timer, jiffies + LINK_TIMER); ++} ++ ++static void ar231x_check_link(struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ u16 phy_data; ++ ++ phy_data = ar231x_mdiobus_read(sp->mii_bus, sp->phy, MII_BMSR); ++ if (sp->phy_data != phy_data) { ++ if (phy_data & BMSR_LSTATUS) { ++ /** ++ * Link is present, ready link partner ability to ++ * deterine duplexity. ++ */ ++ int duplex = 0; ++ u16 reg; ++ ++ sp->link = 1; ++ reg = ar231x_mdiobus_read(sp->mii_bus, sp->phy, ++ MII_BMCR); ++ if (reg & BMCR_ANENABLE) { ++ /* auto neg enabled */ ++ reg = ar231x_mdiobus_read(sp->mii_bus, sp->phy, ++ MII_LPA); ++ duplex = reg & (LPA_100FULL | LPA_10FULL) ? ++ 1 : 0; ++ } else { ++ /* no auto neg, just read duplex config */ ++ duplex = (reg & BMCR_FULLDPLX) ? 1 : 0; ++ } ++ ++ printk(KERN_INFO "%s: Configuring MAC for %s duplex\n", ++ dev->name, (duplex) ? "full" : "half"); ++ ++ if (duplex) { ++ /* full duplex */ ++ sp->eth_regs->mac_control = ++ (sp->eth_regs->mac_control | ++ MAC_CONTROL_F) & ~MAC_CONTROL_DRO; ++ } else { ++ /* half duplex */ ++ sp->eth_regs->mac_control = ++ (sp->eth_regs->mac_control | ++ MAC_CONTROL_DRO) & ~MAC_CONTROL_F; ++ } ++ } else { ++ /* no link */ ++ sp->link = 0; ++ } ++ sp->phy_data = phy_data; ++ } ++} ++ ++static int ar231x_reset_reg(struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ unsigned int ethsal, ethsah; ++ unsigned int flags; ++ ++ sp->cfg->reset_set(sp->cfg->reset_mac); ++ mdelay(10); ++ sp->cfg->reset_clear(sp->cfg->reset_mac); ++ mdelay(10); ++ sp->cfg->reset_set(sp->cfg->reset_phy); ++ mdelay(10); ++ sp->cfg->reset_clear(sp->cfg->reset_phy); ++ mdelay(10); ++ ++ sp->dma_regs->bus_mode = (DMA_BUS_MODE_SWR); ++ mdelay(10); ++ sp->dma_regs->bus_mode = ++ ((32 << DMA_BUS_MODE_PBL_SHIFT) | DMA_BUS_MODE_BLE); ++ ++ /* enable interrupts */ ++ sp->dma_regs->intr_ena = DMA_STATUS_AIS | DMA_STATUS_NIS | ++ DMA_STATUS_RI | DMA_STATUS_TI | ++ DMA_STATUS_FBE; ++ sp->dma_regs->xmt_base = virt_to_phys(sp->tx_ring); ++ sp->dma_regs->rcv_base = virt_to_phys(sp->rx_ring); ++ sp->dma_regs->control = ++ (DMA_CONTROL_SR | DMA_CONTROL_ST | DMA_CONTROL_SF); ++ ++ sp->eth_regs->flow_control = (FLOW_CONTROL_FCE); ++ sp->eth_regs->vlan_tag = (0x8100); ++ ++ /* Enable Ethernet Interface */ ++ flags = (MAC_CONTROL_TE | /* transmit enable */ ++ MAC_CONTROL_PM | /* pass mcast */ ++ MAC_CONTROL_F | /* full duplex */ ++ MAC_CONTROL_HBD); /* heart beat disabled */ ++ ++ if (dev->flags & IFF_PROMISC) { /* set promiscuous mode */ ++ flags |= MAC_CONTROL_PR; ++ } ++ sp->eth_regs->mac_control = flags; ++ ++ /* Set all Ethernet station address registers to their initial values */ ++ ethsah = (((u_int) (dev->dev_addr[5]) << 8) & (u_int) 0x0000FF00) | ++ (((u_int) (dev->dev_addr[4]) << 0) & (u_int) 0x000000FF); ++ ++ ethsal = (((u_int) (dev->dev_addr[3]) << 24) & (u_int) 0xFF000000) | ++ (((u_int) (dev->dev_addr[2]) << 16) & (u_int) 0x00FF0000) | ++ (((u_int) (dev->dev_addr[1]) << 8) & (u_int) 0x0000FF00) | ++ (((u_int) (dev->dev_addr[0]) << 0) & (u_int) 0x000000FF); ++ ++ sp->eth_regs->mac_addr[0] = ethsah; ++ sp->eth_regs->mac_addr[1] = ethsal; ++ ++ mdelay(10); ++ ++ return 0; ++} ++ ++static int ar231x_init(struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ int ecode = 0; ++ ++ /* Allocate descriptors */ ++ if (ar231x_allocate_descriptors(dev)) { ++ printk("%s: %s: ar231x_allocate_descriptors failed\n", ++ dev->name, __func__); ++ ecode = -EAGAIN; ++ goto init_error; ++ } ++ ++ /* Get the memory for the skb rings */ ++ if (sp->rx_skb == NULL) { ++ sp->rx_skb = ++ kmalloc(sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES, ++ GFP_KERNEL); ++ if (!(sp->rx_skb)) { ++ printk("%s: %s: rx_skb kmalloc failed\n", ++ dev->name, __func__); ++ ecode = -EAGAIN; ++ goto init_error; ++ } ++ } ++ memset(sp->rx_skb, 0, sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES); ++ ++ if (sp->tx_skb == NULL) { ++ sp->tx_skb = ++ kmalloc(sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES, ++ GFP_KERNEL); ++ if (!(sp->tx_skb)) { ++ printk("%s: %s: tx_skb kmalloc failed\n", ++ dev->name, __func__); ++ ecode = -EAGAIN; ++ goto init_error; ++ } ++ } ++ memset(sp->tx_skb, 0, sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES); ++ ++ /** ++ * Set tx_csm before we start receiving interrupts, otherwise ++ * the interrupt handler might think it is supposed to process ++ * tx ints before we are up and running, which may cause a null ++ * pointer access in the int handler. ++ */ ++ sp->rx_skbprd = 0; ++ sp->cur_rx = 0; ++ sp->tx_prd = 0; ++ sp->tx_csm = 0; ++ ++ /* Zero the stats before starting the interface */ ++ memset(&dev->stats, 0, sizeof(dev->stats)); ++ ++ /** ++ * We load the ring here as there seem to be no way to tell the ++ * firmware to wipe the ring without re-initializing it. ++ */ ++ ar231x_load_rx_ring(dev, RX_RING_SIZE); ++ ++ /* Init hardware */ ++ ar231x_reset_reg(dev); ++ ++ /* Get the IRQ */ ++ ecode = request_irq(dev->irq, &ar231x_interrupt, 0, ++ dev->name, dev); ++ if (ecode) { ++ printk(KERN_WARNING "%s: %s: Requested IRQ %d is busy\n", ++ dev->name, __func__, dev->irq); ++ goto init_error; ++ } ++ ++ tasklet_enable(&sp->rx_tasklet); ++ ++ return 0; ++ ++init_error: ++ ar231x_init_cleanup(dev); ++ return ecode; ++} ++ ++/** ++ * Load the rx ring. ++ * ++ * Loading rings is safe without holding the spin lock since this is ++ * done only before the device is enabled, thus no interrupts are ++ * generated and by the interrupt handler/tasklet handler. ++ */ ++static void ar231x_load_rx_ring(struct net_device *dev, int nr_bufs) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ short i, idx; ++ ++ idx = sp->rx_skbprd; ++ ++ for (i = 0; i < nr_bufs; i++) { ++ struct sk_buff *skb; ++ ar231x_descr_t *rd; ++ ++ if (sp->rx_skb[idx]) ++ break; ++ ++ skb = netdev_alloc_skb_ip_align(dev, AR2313_BUFSIZE); ++ if (!skb) { ++ printk("\n\n\n\n %s: No memory in system\n\n\n\n", ++ __func__); ++ break; ++ } ++ ++ /* Make sure IP header starts on a fresh cache line */ ++ skb->dev = dev; ++ sp->rx_skb[idx] = skb; ++ ++ rd = (ar231x_descr_t *)&sp->rx_ring[idx]; ++ ++ /* initialize dma descriptor */ ++ rd->devcs = ((AR2313_BUFSIZE << DMA_RX1_BSIZE_SHIFT) | ++ DMA_RX1_CHAINED); ++ rd->addr = virt_to_phys(skb->data); ++ rd->descr = virt_to_phys(&sp->rx_ring[DSC_NEXT(idx)]); ++ rd->status = DMA_RX_OWN; ++ ++ idx = DSC_NEXT(idx); ++ } ++ ++ if (i) ++ sp->rx_skbprd = idx; ++} ++ ++#define AR2313_MAX_PKTS_PER_CALL 64 ++ ++static int ar231x_rx_int(struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ struct sk_buff *skb, *skb_new; ++ ar231x_descr_t *rxdesc; ++ unsigned int status; ++ u32 idx; ++ int pkts = 0; ++ int rval; ++ ++ idx = sp->cur_rx; ++ ++ /* process at most the entire ring and then wait for another int */ ++ while (1) { ++ rxdesc = &sp->rx_ring[idx]; ++ status = rxdesc->status; ++ ++ if (status & DMA_RX_OWN) { ++ /* SiByte owns descriptor or descr not yet filled in */ ++ rval = 0; ++ break; ++ } ++ ++ if (++pkts > AR2313_MAX_PKTS_PER_CALL) { ++ rval = 1; ++ break; ++ } ++ ++ if ((status & DMA_RX_ERROR) && !(status & DMA_RX_LONG)) { ++ dev->stats.rx_errors++; ++ dev->stats.rx_dropped++; ++ ++ /* add statistics counters */ ++ if (status & DMA_RX_ERR_CRC) ++ dev->stats.rx_crc_errors++; ++ if (status & DMA_RX_ERR_COL) ++ dev->stats.rx_over_errors++; ++ if (status & DMA_RX_ERR_LENGTH) ++ dev->stats.rx_length_errors++; ++ if (status & DMA_RX_ERR_RUNT) ++ dev->stats.rx_over_errors++; ++ if (status & DMA_RX_ERR_DESC) ++ dev->stats.rx_over_errors++; ++ ++ } else { ++ /* alloc new buffer. */ ++ skb_new = netdev_alloc_skb_ip_align(dev, ++ AR2313_BUFSIZE); ++ if (skb_new != NULL) { ++ skb = sp->rx_skb[idx]; ++ /* set skb */ ++ skb_put(skb, ((status >> DMA_RX_LEN_SHIFT) & ++ 0x3fff) - CRC_LEN); ++ ++ dev->stats.rx_bytes += skb->len; ++ skb->protocol = eth_type_trans(skb, dev); ++ /* pass the packet to upper layers */ ++ netif_rx(skb); ++ ++ skb_new->dev = dev; ++ /* reset descriptor's curr_addr */ ++ rxdesc->addr = virt_to_phys(skb_new->data); ++ ++ dev->stats.rx_packets++; ++ sp->rx_skb[idx] = skb_new; ++ } else { ++ dev->stats.rx_dropped++; ++ } ++ } ++ ++ rxdesc->devcs = ((AR2313_BUFSIZE << DMA_RX1_BSIZE_SHIFT) | ++ DMA_RX1_CHAINED); ++ rxdesc->status = DMA_RX_OWN; ++ ++ idx = DSC_NEXT(idx); ++ } ++ ++ sp->cur_rx = idx; ++ ++ return rval; ++} ++ ++static void ar231x_tx_int(struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ u32 idx; ++ struct sk_buff *skb; ++ ar231x_descr_t *txdesc; ++ unsigned int status = 0; ++ ++ idx = sp->tx_csm; ++ ++ while (idx != sp->tx_prd) { ++ txdesc = &sp->tx_ring[idx]; ++ status = txdesc->status; ++ ++ if (status & DMA_TX_OWN) { ++ /* ar231x dma still owns descr */ ++ break; ++ } ++ /* done with this descriptor */ ++ dma_unmap_single(NULL, txdesc->addr, ++ txdesc->devcs & DMA_TX1_BSIZE_MASK, ++ DMA_TO_DEVICE); ++ txdesc->status = 0; ++ ++ if (status & DMA_TX_ERROR) { ++ dev->stats.tx_errors++; ++ dev->stats.tx_dropped++; ++ if (status & DMA_TX_ERR_UNDER) ++ dev->stats.tx_fifo_errors++; ++ if (status & DMA_TX_ERR_HB) ++ dev->stats.tx_heartbeat_errors++; ++ if (status & (DMA_TX_ERR_LOSS | DMA_TX_ERR_LINK)) ++ dev->stats.tx_carrier_errors++; ++ if (status & (DMA_TX_ERR_LATE | DMA_TX_ERR_COL | ++ DMA_TX_ERR_JABBER | DMA_TX_ERR_DEFER)) ++ dev->stats.tx_aborted_errors++; ++ } else { ++ /* transmit OK */ ++ dev->stats.tx_packets++; ++ } ++ ++ skb = sp->tx_skb[idx]; ++ sp->tx_skb[idx] = NULL; ++ idx = DSC_NEXT(idx); ++ dev->stats.tx_bytes += skb->len; ++ dev_kfree_skb_irq(skb); ++ } ++ ++ sp->tx_csm = idx; ++} ++ ++static void rx_tasklet_func(unsigned long data) ++{ ++ struct net_device *dev = (struct net_device *)data; ++ struct ar231x_private *sp = netdev_priv(dev); ++ ++ if (sp->unloading) ++ return; ++ ++ if (ar231x_rx_int(dev)) { ++ tasklet_hi_schedule(&sp->rx_tasklet); ++ } else { ++ unsigned long flags; ++ ++ spin_lock_irqsave(&sp->lock, flags); ++ sp->dma_regs->intr_ena |= DMA_STATUS_RI; ++ spin_unlock_irqrestore(&sp->lock, flags); ++ } ++} ++ ++static void rx_schedule(struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ ++ sp->dma_regs->intr_ena &= ~DMA_STATUS_RI; ++ ++ tasklet_hi_schedule(&sp->rx_tasklet); ++} ++ ++static irqreturn_t ar231x_interrupt(int irq, void *dev_id) ++{ ++ struct net_device *dev = (struct net_device *)dev_id; ++ struct ar231x_private *sp = netdev_priv(dev); ++ unsigned int status, enabled; ++ ++ /* clear interrupt */ ++ /* Don't clear RI bit if currently disabled */ ++ status = sp->dma_regs->status; ++ enabled = sp->dma_regs->intr_ena; ++ sp->dma_regs->status = status & enabled; ++ ++ if (status & DMA_STATUS_NIS) { ++ /* normal status */ ++ /** ++ * Don't schedule rx processing if interrupt ++ * is already disabled. ++ */ ++ if (status & enabled & DMA_STATUS_RI) { ++ /* receive interrupt */ ++ rx_schedule(dev); ++ } ++ if (status & DMA_STATUS_TI) { ++ /* transmit interrupt */ ++ ar231x_tx_int(dev); ++ } ++ } ++ ++ /* abnormal status */ ++ if (status & (DMA_STATUS_FBE | DMA_STATUS_TPS)) ++ ar231x_restart(dev); ++ ++ return IRQ_HANDLED; ++} ++ ++static int ar231x_open(struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ unsigned int ethsal, ethsah; ++ ++ /* reset the hardware, in case the MAC address changed */ ++ ethsah = (((u_int) (dev->dev_addr[5]) << 8) & (u_int) 0x0000FF00) | ++ (((u_int) (dev->dev_addr[4]) << 0) & (u_int) 0x000000FF); ++ ++ ethsal = (((u_int) (dev->dev_addr[3]) << 24) & (u_int) 0xFF000000) | ++ (((u_int) (dev->dev_addr[2]) << 16) & (u_int) 0x00FF0000) | ++ (((u_int) (dev->dev_addr[1]) << 8) & (u_int) 0x0000FF00) | ++ (((u_int) (dev->dev_addr[0]) << 0) & (u_int) 0x000000FF); ++ ++ sp->eth_regs->mac_addr[0] = ethsah; ++ sp->eth_regs->mac_addr[1] = ethsal; ++ ++ mdelay(10); ++ ++ dev->mtu = 1500; ++ netif_start_queue(dev); ++ ++ sp->eth_regs->mac_control |= MAC_CONTROL_RE; ++ ++ return 0; ++} ++ ++static void ar231x_tx_timeout(struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ unsigned long flags; ++ ++ spin_lock_irqsave(&sp->lock, flags); ++ ar231x_restart(dev); ++ spin_unlock_irqrestore(&sp->lock, flags); ++} ++ ++static void ar231x_halt(struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ int j; ++ ++ tasklet_disable(&sp->rx_tasklet); ++ ++ /* kill the MAC */ ++ sp->eth_regs->mac_control &= ~(MAC_CONTROL_RE | /* disable Receives */ ++ MAC_CONTROL_TE); /* disable Transmits */ ++ /* stop dma */ ++ sp->dma_regs->control = 0; ++ sp->dma_regs->bus_mode = DMA_BUS_MODE_SWR; ++ ++ /* place phy and MAC in reset */ ++ sp->cfg->reset_set(sp->cfg->reset_mac); ++ sp->cfg->reset_set(sp->cfg->reset_phy); ++ ++ /* free buffers on tx ring */ ++ for (j = 0; j < AR2313_DESCR_ENTRIES; j++) { ++ struct sk_buff *skb; ++ ar231x_descr_t *txdesc; ++ ++ txdesc = &sp->tx_ring[j]; ++ txdesc->descr = 0; ++ ++ skb = sp->tx_skb[j]; ++ if (skb) { ++ dev_kfree_skb(skb); ++ sp->tx_skb[j] = NULL; ++ } ++ } ++} ++ ++/** ++ * close should do nothing. Here's why. It's called when ++ * 'ifconfig bond0 down' is run. If it calls free_irq then ++ * the irq is gone forever ! When bond0 is made 'up' again, ++ * the ar231x_open () does not call request_irq (). Worse, ++ * the call to ar231x_halt() generates a WDOG reset due to ++ * the write to reset register and the box reboots. ++ * Commenting this out is good since it allows the ++ * system to resume when bond0 is made up again. ++ */ ++static int ar231x_close(struct net_device *dev) ++{ ++#if 0 ++ /* Disable interrupts */ ++ disable_irq(dev->irq); ++ ++ /** ++ * Without (or before) releasing irq and stopping hardware, this ++ * is an absolute non-sense, by the way. It will be reset instantly ++ * by the first irq. ++ */ ++ netif_stop_queue(dev); ++ ++ /* stop the MAC and DMA engines */ ++ ar231x_halt(dev); ++ ++ /* release the interrupt */ ++ free_irq(dev->irq, dev); ++ ++#endif ++ return 0; ++} ++ ++static int ar231x_start_xmit(struct sk_buff *skb, struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ ar231x_descr_t *td; ++ u32 idx; ++ ++ idx = sp->tx_prd; ++ td = &sp->tx_ring[idx]; ++ ++ if (td->status & DMA_TX_OWN) { ++ /* free skbuf and lie to the caller that we sent it out */ ++ dev->stats.tx_dropped++; ++ dev_kfree_skb(skb); ++ ++ /* restart transmitter in case locked */ ++ sp->dma_regs->xmt_poll = 0; ++ return 0; ++ } ++ ++ /* Setup the transmit descriptor. */ ++ td->devcs = ((skb->len << DMA_TX1_BSIZE_SHIFT) | ++ (DMA_TX1_LS | DMA_TX1_IC | DMA_TX1_CHAINED)); ++ td->addr = dma_map_single(NULL, skb->data, skb->len, DMA_TO_DEVICE); ++ td->status = DMA_TX_OWN; ++ ++ /* kick transmitter last */ ++ sp->dma_regs->xmt_poll = 0; ++ ++ sp->tx_skb[idx] = skb; ++ idx = DSC_NEXT(idx); ++ sp->tx_prd = idx; ++ ++ return 0; ++} ++ ++static int ar231x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ ++ switch (cmd) { ++ case SIOCGMIIPHY: ++ case SIOCGMIIREG: ++ case SIOCSMIIREG: ++ return phy_mii_ioctl(sp->phy_dev, ifr, cmd); ++ ++ default: ++ break; ++ } ++ ++ return -EOPNOTSUPP; ++} ++ ++static void ar231x_adjust_link(struct net_device *dev) ++{ ++ struct ar231x_private *sp = netdev_priv(dev); ++ unsigned int mc; ++ ++ if (!sp->phy_dev->link) ++ return; ++ ++ if (sp->phy_dev->duplex != sp->oldduplex) { ++ mc = readl(&sp->eth_regs->mac_control); ++ mc &= ~(MAC_CONTROL_F | MAC_CONTROL_DRO); ++ if (sp->phy_dev->duplex) ++ mc |= MAC_CONTROL_F; ++ else ++ mc |= MAC_CONTROL_DRO; ++ writel(mc, &sp->eth_regs->mac_control); ++ sp->oldduplex = sp->phy_dev->duplex; ++ } ++} ++ ++#define MII_ADDR(phy, reg) \ ++ ((reg << MII_ADDR_REG_SHIFT) | (phy << MII_ADDR_PHY_SHIFT)) ++ ++static int ++ar231x_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum) ++{ ++ struct net_device *const dev = bus->priv; ++ struct ar231x_private *sp = netdev_priv(dev); ++ volatile MII *ethernet = sp->phy_regs; ++ ++ ethernet->mii_addr = MII_ADDR(phy_addr, regnum); ++ while (ethernet->mii_addr & MII_ADDR_BUSY) ++ ; ++ return ethernet->mii_data >> MII_DATA_SHIFT; ++} ++ ++static int ++ar231x_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum, u16 value) ++{ ++ struct net_device *const dev = bus->priv; ++ struct ar231x_private *sp = netdev_priv(dev); ++ volatile MII *ethernet = sp->phy_regs; ++ ++ while (ethernet->mii_addr & MII_ADDR_BUSY) ++ ; ++ ethernet->mii_data = value << MII_DATA_SHIFT; ++ ethernet->mii_addr = MII_ADDR(phy_addr, regnum) | MII_ADDR_WRITE; ++ ++ return 0; ++} ++ ++static int ar231x_mdiobus_reset(struct mii_bus *bus) ++{ ++ struct net_device *const dev = bus->priv; ++ ++ ar231x_reset_reg(dev); ++ ++ return 0; ++} ++ ++static int ar231x_mdiobus_probe(struct net_device *dev) ++{ ++ struct ar231x_private *const sp = netdev_priv(dev); ++ struct phy_device *phydev = NULL; ++ int phy_addr; ++ ++ /* find the first (lowest address) PHY on the current MAC's MII bus */ ++ for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++) ++ if (sp->mii_bus->phy_map[phy_addr]) { ++ phydev = sp->mii_bus->phy_map[phy_addr]; ++ sp->phy = phy_addr; ++ break; /* break out with first one found */ ++ } ++ ++ if (!phydev) { ++ printk(KERN_ERR "ar231x: %s: no PHY found\n", dev->name); ++ return -1; ++ } ++ ++ /* now we are supposed to have a proper phydev, to attach to... */ ++ BUG_ON(!phydev); ++ BUG_ON(phydev->attached_dev); ++ ++ phydev = phy_connect(dev, dev_name(&phydev->dev), &ar231x_adjust_link, ++ PHY_INTERFACE_MODE_MII); ++ ++ if (IS_ERR(phydev)) { ++ printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name); ++ return PTR_ERR(phydev); ++ } ++ ++ /* mask with MAC supported features */ ++ phydev->supported &= (SUPPORTED_10baseT_Half ++ | SUPPORTED_10baseT_Full ++ | SUPPORTED_100baseT_Half ++ | SUPPORTED_100baseT_Full ++ | SUPPORTED_Autoneg ++ /* | SUPPORTED_Pause | SUPPORTED_Asym_Pause */ ++ | SUPPORTED_MII ++ | SUPPORTED_TP); ++ ++ phydev->advertising = phydev->supported; ++ ++ sp->oldduplex = -1; ++ sp->phy_dev = phydev; ++ ++ printk(KERN_INFO "%s: attached PHY driver [%s] (mii_bus:phy_addr=%s)\n", ++ dev->name, phydev->drv->name, dev_name(&phydev->dev)); ++ ++ return 0; ++} ++ +--- /dev/null ++++ b/drivers/net/ethernet/atheros/ar231x/ar231x.h +@@ -0,0 +1,288 @@ ++/* ++ * ar231x.h: Linux driver for the Atheros AR231x Ethernet device. ++ * ++ * Copyright (C) 2004 by Sameer Dekate ++ * Copyright (C) 2006 Imre Kaloz ++ * Copyright (C) 2006-2009 Felix Fietkau ++ * ++ * Thanks to Atheros for providing hardware and documentation ++ * enabling me to write this driver. ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License as published by ++ * the Free Software Foundation; either version 2 of the License, or ++ * (at your option) any later version. ++ */ ++ ++#ifndef _AR2313_H_ ++#define _AR2313_H_ ++ ++#include ++#include ++#include ++#include ++ ++/* probe link timer - 5 secs */ ++#define LINK_TIMER (5*HZ) ++ ++#define IS_DMA_TX_INT(X) (((X) & (DMA_STATUS_TI)) != 0) ++#define IS_DMA_RX_INT(X) (((X) & (DMA_STATUS_RI)) != 0) ++#define IS_DRIVER_OWNED(X) (((X) & (DMA_TX_OWN)) == 0) ++ ++#define AR2313_TX_TIMEOUT (HZ/4) ++ ++/* Rings */ ++#define DSC_RING_ENTRIES_SIZE (AR2313_DESCR_ENTRIES * sizeof(struct desc)) ++#define DSC_NEXT(idx) ((idx + 1) & (AR2313_DESCR_ENTRIES - 1)) ++ ++#define AR2313_MBGET 2 ++#define AR2313_MBSET 3 ++#define AR2313_PCI_RECONFIG 4 ++#define AR2313_PCI_DUMP 5 ++#define AR2313_TEST_PANIC 6 ++#define AR2313_TEST_NULLPTR 7 ++#define AR2313_READ_DATA 8 ++#define AR2313_WRITE_DATA 9 ++#define AR2313_GET_VERSION 10 ++#define AR2313_TEST_HANG 11 ++#define AR2313_SYNC 12 ++ ++#define DMA_RX_ERR_CRC BIT(1) ++#define DMA_RX_ERR_DRIB BIT(2) ++#define DMA_RX_ERR_MII BIT(3) ++#define DMA_RX_EV2 BIT(5) ++#define DMA_RX_ERR_COL BIT(6) ++#define DMA_RX_LONG BIT(7) ++#define DMA_RX_LS BIT(8) /* last descriptor */ ++#define DMA_RX_FS BIT(9) /* first descriptor */ ++#define DMA_RX_MF BIT(10) /* multicast frame */ ++#define DMA_RX_ERR_RUNT BIT(11) /* runt frame */ ++#define DMA_RX_ERR_LENGTH BIT(12) /* length error */ ++#define DMA_RX_ERR_DESC BIT(14) /* descriptor error */ ++#define DMA_RX_ERROR BIT(15) /* error summary */ ++#define DMA_RX_LEN_MASK 0x3fff0000 ++#define DMA_RX_LEN_SHIFT 16 ++#define DMA_RX_FILT BIT(30) ++#define DMA_RX_OWN BIT(31) /* desc owned by DMA controller */ ++ ++#define DMA_RX1_BSIZE_MASK 0x000007ff ++#define DMA_RX1_BSIZE_SHIFT 0 ++#define DMA_RX1_CHAINED BIT(24) ++#define DMA_RX1_RER BIT(25) ++ ++#define DMA_TX_ERR_UNDER BIT(1) /* underflow error */ ++#define DMA_TX_ERR_DEFER BIT(2) /* excessive deferral */ ++#define DMA_TX_COL_MASK 0x78 ++#define DMA_TX_COL_SHIFT 3 ++#define DMA_TX_ERR_HB BIT(7) /* hearbeat failure */ ++#define DMA_TX_ERR_COL BIT(8) /* excessive collisions */ ++#define DMA_TX_ERR_LATE BIT(9) /* late collision */ ++#define DMA_TX_ERR_LINK BIT(10) /* no carrier */ ++#define DMA_TX_ERR_LOSS BIT(11) /* loss of carrier */ ++#define DMA_TX_ERR_JABBER BIT(14) /* transmit jabber timeout */ ++#define DMA_TX_ERROR BIT(15) /* frame aborted */ ++#define DMA_TX_OWN BIT(31) /* descr owned by DMA controller */ ++ ++#define DMA_TX1_BSIZE_MASK 0x000007ff ++#define DMA_TX1_BSIZE_SHIFT 0 ++#define DMA_TX1_CHAINED BIT(24) /* chained descriptors */ ++#define DMA_TX1_TER BIT(25) /* transmit end of ring */ ++#define DMA_TX1_FS BIT(29) /* first segment */ ++#define DMA_TX1_LS BIT(30) /* last segment */ ++#define DMA_TX1_IC BIT(31) /* interrupt on completion */ ++ ++#define RCVPKT_LENGTH(X) (X >> 16) /* Received pkt Length */ ++ ++#define MAC_CONTROL_RE BIT(2) /* receive enable */ ++#define MAC_CONTROL_TE BIT(3) /* transmit enable */ ++#define MAC_CONTROL_DC BIT(5) /* Deferral check */ ++#define MAC_CONTROL_ASTP BIT(8) /* Auto pad strip */ ++#define MAC_CONTROL_DRTY BIT(10) /* Disable retry */ ++#define MAC_CONTROL_DBF BIT(11) /* Disable bcast frames */ ++#define MAC_CONTROL_LCC BIT(12) /* late collision ctrl */ ++#define MAC_CONTROL_HP BIT(13) /* Hash Perfect filtering */ ++#define MAC_CONTROL_HASH BIT(14) /* Unicast hash filtering */ ++#define MAC_CONTROL_HO BIT(15) /* Hash only filtering */ ++#define MAC_CONTROL_PB BIT(16) /* Pass Bad frames */ ++#define MAC_CONTROL_IF BIT(17) /* Inverse filtering */ ++#define MAC_CONTROL_PR BIT(18) /* promis mode (valid frames only) */ ++#define MAC_CONTROL_PM BIT(19) /* pass multicast */ ++#define MAC_CONTROL_F BIT(20) /* full-duplex */ ++#define MAC_CONTROL_DRO BIT(23) /* Disable Receive Own */ ++#define MAC_CONTROL_HBD BIT(28) /* heart-beat disabled (MUST BE SET) */ ++#define MAC_CONTROL_BLE BIT(30) /* big endian mode */ ++#define MAC_CONTROL_RA BIT(31) /* rcv all (valid and invalid frames) */ ++ ++#define MII_ADDR_BUSY BIT(0) ++#define MII_ADDR_WRITE BIT(1) ++#define MII_ADDR_REG_SHIFT 6 ++#define MII_ADDR_PHY_SHIFT 11 ++#define MII_DATA_SHIFT 0 ++ ++#define FLOW_CONTROL_FCE BIT(1) ++ ++#define DMA_BUS_MODE_SWR BIT(0) /* software reset */ ++#define DMA_BUS_MODE_BLE BIT(7) /* big endian mode */ ++#define DMA_BUS_MODE_PBL_SHIFT 8 /* programmable burst length 32 */ ++#define DMA_BUS_MODE_DBO BIT(20) /* big-endian descriptors */ ++ ++#define DMA_STATUS_TI BIT(0) /* transmit interrupt */ ++#define DMA_STATUS_TPS BIT(1) /* transmit process stopped */ ++#define DMA_STATUS_TU BIT(2) /* transmit buffer unavailable */ ++#define DMA_STATUS_TJT BIT(3) /* transmit buffer timeout */ ++#define DMA_STATUS_UNF BIT(5) /* transmit underflow */ ++#define DMA_STATUS_RI BIT(6) /* receive interrupt */ ++#define DMA_STATUS_RU BIT(7) /* receive buffer unavailable */ ++#define DMA_STATUS_RPS BIT(8) /* receive process stopped */ ++#define DMA_STATUS_ETI BIT(10) /* early transmit interrupt */ ++#define DMA_STATUS_FBE BIT(13) /* fatal bus interrupt */ ++#define DMA_STATUS_ERI BIT(14) /* early receive interrupt */ ++#define DMA_STATUS_AIS BIT(15) /* abnormal interrupt summary */ ++#define DMA_STATUS_NIS BIT(16) /* normal interrupt summary */ ++#define DMA_STATUS_RS_SHIFT 17 /* receive process state */ ++#define DMA_STATUS_TS_SHIFT 20 /* transmit process state */ ++#define DMA_STATUS_EB_SHIFT 23 /* error bits */ ++ ++#define DMA_CONTROL_SR BIT(1) /* start receive */ ++#define DMA_CONTROL_ST BIT(13) /* start transmit */ ++#define DMA_CONTROL_SF BIT(21) /* store and forward */ ++ ++typedef struct { ++ volatile unsigned int status; /* OWN, Device control and status. */ ++ volatile unsigned int devcs; /* pkt Control bits + Length */ ++ volatile unsigned int addr; /* Current Address. */ ++ volatile unsigned int descr; /* Next descriptor in chain. */ ++} ar231x_descr_t; ++ ++/** ++ * New Combo structure for Both Eth0 AND eth1 ++ * ++ * Don't directly access MII related regs since phy chip could be actually ++ * connected to another ethernet block. ++ */ ++typedef struct { ++ volatile unsigned int mac_control; /* 0x00 */ ++ volatile unsigned int mac_addr[2]; /* 0x04 - 0x08 */ ++ volatile unsigned int mcast_table[2]; /* 0x0c - 0x10 */ ++ volatile unsigned int __mii_addr; /* 0x14 */ ++ volatile unsigned int __mii_data; /* 0x18 */ ++ volatile unsigned int flow_control; /* 0x1c */ ++ volatile unsigned int vlan_tag; /* 0x20 */ ++ volatile unsigned int pad[7]; /* 0x24 - 0x3c */ ++ volatile unsigned int ucast_table[8]; /* 0x40-0x5c */ ++} ETHERNET_STRUCT; ++ ++typedef struct { ++ volatile unsigned int mii_addr; ++ volatile unsigned int mii_data; ++} MII; ++ ++/******************************************************************** ++ * Interrupt controller ++ ********************************************************************/ ++ ++typedef struct { ++ volatile unsigned int wdog_control; /* 0x08 */ ++ volatile unsigned int wdog_timer; /* 0x0c */ ++ volatile unsigned int misc_status; /* 0x10 */ ++ volatile unsigned int misc_mask; /* 0x14 */ ++ volatile unsigned int global_status; /* 0x18 */ ++ volatile unsigned int reserved; /* 0x1c */ ++ volatile unsigned int reset_control; /* 0x20 */ ++} INTERRUPT; ++ ++/******************************************************************** ++ * DMA controller ++ ********************************************************************/ ++typedef struct { ++ volatile unsigned int bus_mode; /* 0x00 (CSR0) */ ++ volatile unsigned int xmt_poll; /* 0x04 (CSR1) */ ++ volatile unsigned int rcv_poll; /* 0x08 (CSR2) */ ++ volatile unsigned int rcv_base; /* 0x0c (CSR3) */ ++ volatile unsigned int xmt_base; /* 0x10 (CSR4) */ ++ volatile unsigned int status; /* 0x14 (CSR5) */ ++ volatile unsigned int control; /* 0x18 (CSR6) */ ++ volatile unsigned int intr_ena; /* 0x1c (CSR7) */ ++ volatile unsigned int rcv_missed; /* 0x20 (CSR8) */ ++ volatile unsigned int reserved[11]; /* 0x24-0x4c (CSR9-19) */ ++ volatile unsigned int cur_tx_buf_addr; /* 0x50 (CSR20) */ ++ volatile unsigned int cur_rx_buf_addr; /* 0x50 (CSR21) */ ++} DMA; ++ ++/** ++ * Struct private for the Sibyte. ++ * ++ * Elements are grouped so variables used by the tx handling goes ++ * together, and will go into the same cache lines etc. in order to ++ * avoid cache line contention between the rx and tx handling on SMP. ++ * ++ * Frequently accessed variables are put at the beginning of the ++ * struct to help the compiler generate better/shorter code. ++ */ ++struct ar231x_private { ++ struct net_device *dev; ++ int version; ++ u32 mb[2]; ++ ++ volatile MII *phy_regs; ++ volatile ETHERNET_STRUCT *eth_regs; ++ volatile DMA *dma_regs; ++ struct ar231x_eth *cfg; ++ ++ spinlock_t lock; /* Serialise access to device */ ++ ++ /* RX and TX descriptors, must be adjacent */ ++ ar231x_descr_t *rx_ring; ++ ar231x_descr_t *tx_ring; ++ ++ struct sk_buff **rx_skb; ++ struct sk_buff **tx_skb; ++ ++ /* RX elements */ ++ u32 rx_skbprd; ++ u32 cur_rx; ++ ++ /* TX elements */ ++ u32 tx_prd; ++ u32 tx_csm; ++ ++ /* Misc elements */ ++ char name[48]; ++ struct { ++ u32 address; ++ u32 length; ++ char *mapping; ++ } desc; ++ ++ struct timer_list link_timer; ++ unsigned short phy; /* merlot phy = 1, samsung phy = 0x1f */ ++ unsigned short mac; ++ unsigned short link; /* 0 - link down, 1 - link up */ ++ u16 phy_data; ++ ++ struct tasklet_struct rx_tasklet; ++ int unloading; ++ ++ struct phy_device *phy_dev; ++ struct mii_bus *mii_bus; ++ int oldduplex; ++}; ++ ++/* Prototypes */ ++static int ar231x_init(struct net_device *dev); ++#ifdef TX_TIMEOUT ++static void ar231x_tx_timeout(struct net_device *dev); ++#endif ++static int ar231x_restart(struct net_device *dev); ++static void ar231x_load_rx_ring(struct net_device *dev, int bufs); ++static irqreturn_t ar231x_interrupt(int irq, void *dev_id); ++static int ar231x_open(struct net_device *dev); ++static int ar231x_start_xmit(struct sk_buff *skb, struct net_device *dev); ++static int ar231x_close(struct net_device *dev); ++static int ar231x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd); ++static void ar231x_init_cleanup(struct net_device *dev); ++static int ar231x_setup_timer(struct net_device *dev); ++static void ar231x_link_timer_fn(unsigned long data); ++static void ar231x_check_link(struct net_device *dev); ++ ++#endif /* _AR2313_H_ */ +--- a/arch/mips/ath25/ar2315_regs.h ++++ b/arch/mips/ath25/ar2315_regs.h +@@ -57,6 +57,9 @@ + #define AR2315_PCI_EXT_BASE 0x80000000 /* PCI external */ + #define AR2315_PCI_EXT_SIZE 0x40000000 + ++/* MII registers offset inside Ethernet MMR region */ ++#define AR2315_ENET0_MII_BASE (AR2315_ENET0_BASE + 0x14) ++ + /* + * Configuration registers + */ +--- a/arch/mips/ath25/ar5312_regs.h ++++ b/arch/mips/ath25/ar5312_regs.h +@@ -64,6 +64,10 @@ + #define AR5312_AR5312_REV7 0x0057 /* AR5312 WMAC (AP30-040) */ + #define AR5312_AR2313_REV8 0x0058 /* AR2313 WMAC (AP43-030) */ + ++/* MII registers offset inside Ethernet MMR region */ ++#define AR5312_ENET0_MII_BASE (AR5312_ENET0_BASE + 0x14) ++#define AR5312_ENET1_MII_BASE (AR5312_ENET1_BASE + 0x14) ++ + /* Reset/Timer Block Address Map */ + #define AR5312_TIMER 0x0000 /* countdown timer */ + #define AR5312_RELOAD 0x0004 /* timer reload value */ +--- a/arch/mips/ath25/ar2315.c ++++ b/arch/mips/ath25/ar2315.c +@@ -136,6 +136,8 @@ static void ar2315_irq_dispatch(void) + + if (pending & CAUSEF_IP3) + do_IRQ(AR2315_IRQ_WLAN0); ++ else if (pending & CAUSEF_IP4) ++ do_IRQ(AR2315_IRQ_ENET0); + #ifdef CONFIG_PCI_AR2315 + else if (pending & CAUSEF_IP5) + do_IRQ(AR2315_IRQ_LCBUS_PCI); +@@ -169,6 +171,29 @@ void __init ar2315_arch_init_irq(void) + ar2315_misc_irq_domain = domain; + } + ++static void ar2315_device_reset_set(u32 mask) ++{ ++ u32 val; ++ ++ val = ar2315_rst_reg_read(AR2315_RESET); ++ ar2315_rst_reg_write(AR2315_RESET, val | mask); ++} ++ ++static void ar2315_device_reset_clear(u32 mask) ++{ ++ u32 val; ++ ++ val = ar2315_rst_reg_read(AR2315_RESET); ++ ar2315_rst_reg_write(AR2315_RESET, val & ~mask); ++} ++ ++static struct ar231x_eth ar2315_eth_data = { ++ .reset_set = ar2315_device_reset_set, ++ .reset_clear = ar2315_device_reset_clear, ++ .reset_mac = AR2315_RESET_ENET0, ++ .reset_phy = AR2315_RESET_EPHY0, ++}; ++ + static struct resource ar2315_gpio_res[] = { + { + .name = "ar2315-gpio", +@@ -205,6 +230,11 @@ void __init ar2315_init_devices(void) + ar2315_gpio_res[1].end = ar2315_gpio_res[1].start; + platform_device_register(&ar2315_gpio); + ++ ar2315_eth_data.macaddr = ath25_board.config->enet0_mac; ++ ath25_add_ethernet(0, AR2315_ENET0_BASE, "eth0_mii", ++ AR2315_ENET0_MII_BASE, AR2315_IRQ_ENET0, ++ &ar2315_eth_data); ++ + ath25_add_wmac(0, AR2315_WLAN0_BASE, AR2315_IRQ_WLAN0); + } + +--- a/arch/mips/ath25/ar5312.c ++++ b/arch/mips/ath25/ar5312.c +@@ -132,6 +132,10 @@ static void ar5312_irq_dispatch(void) + + if (pending & CAUSEF_IP2) + do_IRQ(AR5312_IRQ_WLAN0); ++ else if (pending & CAUSEF_IP3) ++ do_IRQ(AR5312_IRQ_ENET0); ++ else if (pending & CAUSEF_IP4) ++ do_IRQ(AR5312_IRQ_ENET1); + else if (pending & CAUSEF_IP5) + do_IRQ(AR5312_IRQ_WLAN1); + else if (pending & CAUSEF_IP6) +@@ -163,6 +167,36 @@ void __init ar5312_arch_init_irq(void) + ar5312_misc_irq_domain = domain; + } + ++static void ar5312_device_reset_set(u32 mask) ++{ ++ u32 val; ++ ++ val = ar5312_rst_reg_read(AR5312_RESET); ++ ar5312_rst_reg_write(AR5312_RESET, val | mask); ++} ++ ++static void ar5312_device_reset_clear(u32 mask) ++{ ++ u32 val; ++ ++ val = ar5312_rst_reg_read(AR5312_RESET); ++ ar5312_rst_reg_write(AR5312_RESET, val & ~mask); ++} ++ ++static struct ar231x_eth ar5312_eth0_data = { ++ .reset_set = ar5312_device_reset_set, ++ .reset_clear = ar5312_device_reset_clear, ++ .reset_mac = AR5312_RESET_ENET0, ++ .reset_phy = AR5312_RESET_EPHY0, ++}; ++ ++static struct ar231x_eth ar5312_eth1_data = { ++ .reset_set = ar5312_device_reset_set, ++ .reset_clear = ar5312_device_reset_clear, ++ .reset_mac = AR5312_RESET_ENET1, ++ .reset_phy = AR5312_RESET_EPHY1, ++}; ++ + static struct physmap_flash_data ar5312_flash_data = { + .width = 2, + }; +@@ -243,6 +277,7 @@ static void __init ar5312_flash_init(voi + void __init ar5312_init_devices(void) + { + struct ath25_boarddata *config; ++ u8 *c; + + ar5312_flash_init(); + +@@ -266,8 +301,30 @@ void __init ar5312_init_devices(void) + + platform_device_register(&ar5312_gpio); + ++ /* Fix up MAC addresses if necessary */ ++ if (is_broadcast_ether_addr(config->enet0_mac)) ++ ether_addr_copy(config->enet0_mac, config->enet1_mac); ++ ++ /* If ENET0 and ENET1 have the same mac address, ++ * increment the one from ENET1 */ ++ if (ether_addr_equal(config->enet0_mac, config->enet1_mac)) { ++ c = config->enet1_mac + 5; ++ while ((c >= config->enet1_mac) && !(++(*c))) ++ c--; ++ } ++ + switch (ath25_soc) { + case ATH25_SOC_AR5312: ++ ar5312_eth0_data.macaddr = config->enet0_mac; ++ ath25_add_ethernet(0, AR5312_ENET0_BASE, "eth0_mii", ++ AR5312_ENET0_MII_BASE, AR5312_IRQ_ENET0, ++ &ar5312_eth0_data); ++ ++ ar5312_eth1_data.macaddr = config->enet1_mac; ++ ath25_add_ethernet(1, AR5312_ENET1_BASE, "eth1_mii", ++ AR5312_ENET1_MII_BASE, AR5312_IRQ_ENET1, ++ &ar5312_eth1_data); ++ + if (!ath25_board.radio) + return; + +@@ -276,8 +333,18 @@ void __init ar5312_init_devices(void) + + ath25_add_wmac(0, AR5312_WLAN0_BASE, AR5312_IRQ_WLAN0); + break; ++ /* ++ * AR2312/3 ethernet uses the PHY of ENET0, but the MAC ++ * of ENET1. Atheros calls it 'twisted' for a reason :) ++ */ + case ATH25_SOC_AR2312: + case ATH25_SOC_AR2313: ++ ar5312_eth1_data.reset_phy = ar5312_eth0_data.reset_phy; ++ ar5312_eth1_data.macaddr = config->enet0_mac; ++ ath25_add_ethernet(1, AR5312_ENET1_BASE, "eth0_mii", ++ AR5312_ENET0_MII_BASE, AR5312_IRQ_ENET1, ++ &ar5312_eth1_data); ++ + if (!ath25_board.radio) + return; + break; +--- a/arch/mips/ath25/devices.h ++++ b/arch/mips/ath25/devices.h +@@ -32,6 +32,8 @@ extern struct ar231x_board_config ath25_ + extern void (*ath25_irq_dispatch)(void); + + int ath25_find_config(phys_addr_t offset, unsigned long size); ++int ath25_add_ethernet(int nr, u32 base, const char *mii_name, u32 mii_base, ++ int irq, void *pdata); + void ath25_serial_setup(u32 mapbase, int irq, unsigned int uartclk); + int ath25_add_wmac(int nr, u32 base, int irq); + +--- a/arch/mips/ath25/devices.c ++++ b/arch/mips/ath25/devices.c +@@ -12,6 +12,51 @@ + struct ar231x_board_config ath25_board; + enum ath25_soc_type ath25_soc = ATH25_SOC_UNKNOWN; + ++static struct resource ath25_eth0_res[] = { ++ { ++ .name = "eth0_membase", ++ .flags = IORESOURCE_MEM, ++ }, ++ { ++ .name = "eth0_mii", ++ .flags = IORESOURCE_MEM, ++ }, ++ { ++ .name = "eth0_irq", ++ .flags = IORESOURCE_IRQ, ++ } ++}; ++ ++static struct resource ath25_eth1_res[] = { ++ { ++ .name = "eth1_membase", ++ .flags = IORESOURCE_MEM, ++ }, ++ { ++ .name = "eth1_mii", ++ .flags = IORESOURCE_MEM, ++ }, ++ { ++ .name = "eth1_irq", ++ .flags = IORESOURCE_IRQ, ++ } ++}; ++ ++static struct platform_device ath25_eth[] = { ++ { ++ .id = 0, ++ .name = "ar231x-eth", ++ .resource = ath25_eth0_res, ++ .num_resources = ARRAY_SIZE(ath25_eth0_res) ++ }, ++ { ++ .id = 1, ++ .name = "ar231x-eth", ++ .resource = ath25_eth1_res, ++ .num_resources = ARRAY_SIZE(ath25_eth1_res) ++ } ++}; ++ + static struct resource ath25_wmac0_res[] = { + { + .name = "wmac0_membase", +@@ -70,6 +115,25 @@ const char *get_system_type(void) + return soc_type_strings[ath25_soc]; + } + ++int __init ath25_add_ethernet(int nr, u32 base, const char *mii_name, ++ u32 mii_base, int irq, void *pdata) ++{ ++ struct resource *res; ++ ++ ath25_eth[nr].dev.platform_data = pdata; ++ res = &ath25_eth[nr].resource[0]; ++ res->start = base; ++ res->end = base + 0x2000 - 1; ++ res++; ++ res->name = mii_name; ++ res->start = mii_base; ++ res->end = mii_base + 8 - 1; ++ res++; ++ res->start = irq; ++ res->end = irq; ++ return platform_device_register(&ath25_eth[nr]); ++} ++ + void __init ath25_serial_setup(u32 mapbase, int irq, unsigned int uartclk) + { + struct uart_port s; +--- a/arch/mips/include/asm/mach-ath25/ath25_platform.h ++++ b/arch/mips/include/asm/mach-ath25/ath25_platform.h +@@ -70,4 +70,15 @@ struct ar231x_board_config { + const char *radio; + }; + ++/* ++ * Platform device information for the Ethernet MAC ++ */ ++struct ar231x_eth { ++ void (*reset_set)(u32); ++ void (*reset_clear)(u32); ++ u32 reset_mac; ++ u32 reset_phy; ++ char *macaddr; ++}; ++ + #endif /* __ASM_MACH_ATH25_PLATFORM_H */ diff --git a/target/linux/ath25/patches-4.9/120-spiflash.patch b/target/linux/ath25/patches-4.9/120-spiflash.patch new file mode 100644 index 0000000000..695ea4303a --- /dev/null +++ b/target/linux/ath25/patches-4.9/120-spiflash.patch @@ -0,0 +1,634 @@ +--- a/drivers/mtd/devices/Kconfig ++++ b/drivers/mtd/devices/Kconfig +@@ -120,6 +120,10 @@ config MTD_BCM47XXSFLASH + registered by bcma as platform devices. This enables driver for + serial flash memories. + ++config MTD_AR2315 ++ tristate "Atheros AR2315+ SPI Flash support" ++ depends on SOC_AR2315 ++ + config MTD_SLRAM + tristate "Uncached system RAM" + help +--- a/drivers/mtd/devices/Makefile ++++ b/drivers/mtd/devices/Makefile +@@ -14,6 +14,7 @@ obj-$(CONFIG_MTD_DATAFLASH) += mtd_dataf + obj-$(CONFIG_MTD_M25P80) += m25p80.o + obj-$(CONFIG_MTD_SPEAR_SMI) += spear_smi.o + obj-$(CONFIG_MTD_SST25L) += sst25l.o ++obj-$(CONFIG_MTD_AR2315) += ar2315.o + obj-$(CONFIG_MTD_BCM47XXSFLASH) += bcm47xxsflash.o + obj-$(CONFIG_MTD_ST_SPI_FSM) += st_spi_fsm.o + obj-$(CONFIG_MTD_POWERNV_FLASH) += powernv_flash.o +--- /dev/null ++++ b/drivers/mtd/devices/ar2315.c +@@ -0,0 +1,459 @@ ++ ++/* ++ * MTD driver for the SPI Flash Memory support on Atheros AR2315 ++ * ++ * Copyright (c) 2005-2006 Atheros Communications Inc. ++ * Copyright (C) 2006-2007 FON Technology, SL. ++ * Copyright (C) 2006-2007 Imre Kaloz ++ * Copyright (C) 2006-2009 Felix Fietkau ++ * Copyright (C) 2012 Alexandros C. Couloumbis ++ * ++ * This code is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "ar2315_spiflash.h" ++ ++#define DRIVER_NAME "ar2315-spiflash" ++ ++#define busy_wait(_priv, _condition, _wait) do { \ ++ while (_condition) { \ ++ if (_wait > 1) \ ++ msleep(_wait); \ ++ else if ((_wait == 1) && need_resched()) \ ++ schedule(); \ ++ else \ ++ udelay(1); \ ++ } \ ++} while (0) ++ ++enum { ++ FLASH_NONE, ++ FLASH_1MB, ++ FLASH_2MB, ++ FLASH_4MB, ++ FLASH_8MB, ++ FLASH_16MB, ++}; ++ ++/* Flash configuration table */ ++struct flashconfig { ++ u32 byte_cnt; ++ u32 sector_cnt; ++ u32 sector_size; ++}; ++ ++static const struct flashconfig flashconfig_tbl[] = { ++ [FLASH_NONE] = { 0, 0, 0}, ++ [FLASH_1MB] = { STM_1MB_BYTE_COUNT, STM_1MB_SECTOR_COUNT, ++ STM_1MB_SECTOR_SIZE}, ++ [FLASH_2MB] = { STM_2MB_BYTE_COUNT, STM_2MB_SECTOR_COUNT, ++ STM_2MB_SECTOR_SIZE}, ++ [FLASH_4MB] = { STM_4MB_BYTE_COUNT, STM_4MB_SECTOR_COUNT, ++ STM_4MB_SECTOR_SIZE}, ++ [FLASH_8MB] = { STM_8MB_BYTE_COUNT, STM_8MB_SECTOR_COUNT, ++ STM_8MB_SECTOR_SIZE}, ++ [FLASH_16MB] = { STM_16MB_BYTE_COUNT, STM_16MB_SECTOR_COUNT, ++ STM_16MB_SECTOR_SIZE} ++}; ++ ++/* Mapping of generic opcodes to STM serial flash opcodes */ ++enum { ++ SPI_WRITE_ENABLE, ++ SPI_WRITE_DISABLE, ++ SPI_RD_STATUS, ++ SPI_WR_STATUS, ++ SPI_RD_DATA, ++ SPI_FAST_RD_DATA, ++ SPI_PAGE_PROGRAM, ++ SPI_SECTOR_ERASE, ++ SPI_BULK_ERASE, ++ SPI_DEEP_PWRDOWN, ++ SPI_RD_SIG, ++}; ++ ++struct opcodes { ++ __u16 code; ++ __s8 tx_cnt; ++ __s8 rx_cnt; ++}; ++ ++static const struct opcodes stm_opcodes[] = { ++ [SPI_WRITE_ENABLE] = {STM_OP_WR_ENABLE, 1, 0}, ++ [SPI_WRITE_DISABLE] = {STM_OP_WR_DISABLE, 1, 0}, ++ [SPI_RD_STATUS] = {STM_OP_RD_STATUS, 1, 1}, ++ [SPI_WR_STATUS] = {STM_OP_WR_STATUS, 1, 0}, ++ [SPI_RD_DATA] = {STM_OP_RD_DATA, 4, 4}, ++ [SPI_FAST_RD_DATA] = {STM_OP_FAST_RD_DATA, 5, 0}, ++ [SPI_PAGE_PROGRAM] = {STM_OP_PAGE_PGRM, 8, 0}, ++ [SPI_SECTOR_ERASE] = {STM_OP_SECTOR_ERASE, 4, 0}, ++ [SPI_BULK_ERASE] = {STM_OP_BULK_ERASE, 1, 0}, ++ [SPI_DEEP_PWRDOWN] = {STM_OP_DEEP_PWRDOWN, 1, 0}, ++ [SPI_RD_SIG] = {STM_OP_RD_SIG, 4, 1}, ++}; ++ ++/* Driver private data structure */ ++struct spiflash_priv { ++ struct mtd_info mtd; ++ void __iomem *readaddr; /* memory mapped data for read */ ++ void __iomem *mmraddr; /* memory mapped register space */ ++ struct mutex lock; /* serialize registers access */ ++}; ++ ++#define to_spiflash(_mtd) container_of(_mtd, struct spiflash_priv, mtd) ++ ++enum { ++ FL_READY, ++ FL_READING, ++ FL_ERASING, ++ FL_WRITING ++}; ++ ++/*****************************************************************************/ ++ ++static u32 ++spiflash_read_reg(struct spiflash_priv *priv, int reg) ++{ ++ return ioread32(priv->mmraddr + reg); ++} ++ ++static void ++spiflash_write_reg(struct spiflash_priv *priv, int reg, u32 data) ++{ ++ iowrite32(data, priv->mmraddr + reg); ++} ++ ++static u32 ++spiflash_wait_busy(struct spiflash_priv *priv) ++{ ++ u32 reg; ++ ++ busy_wait(priv, (reg = spiflash_read_reg(priv, SPI_FLASH_CTL)) & ++ SPI_CTL_BUSY, 0); ++ return reg; ++} ++ ++static u32 ++spiflash_sendcmd(struct spiflash_priv *priv, int opcode, u32 addr) ++{ ++ const struct opcodes *op; ++ u32 reg, mask; ++ ++ op = &stm_opcodes[opcode]; ++ reg = spiflash_wait_busy(priv); ++ spiflash_write_reg(priv, SPI_FLASH_OPCODE, ++ ((u32)op->code) | (addr << 8)); ++ ++ reg &= ~SPI_CTL_TX_RX_CNT_MASK; ++ reg |= SPI_CTL_START | op->tx_cnt | (op->rx_cnt << 4); ++ ++ spiflash_write_reg(priv, SPI_FLASH_CTL, reg); ++ spiflash_wait_busy(priv); ++ ++ if (!op->rx_cnt) ++ return 0; ++ ++ reg = spiflash_read_reg(priv, SPI_FLASH_DATA); ++ ++ switch (op->rx_cnt) { ++ case 1: ++ mask = 0x000000ff; ++ break; ++ case 2: ++ mask = 0x0000ffff; ++ break; ++ case 3: ++ mask = 0x00ffffff; ++ break; ++ default: ++ mask = 0xffffffff; ++ break; ++ } ++ reg &= mask; ++ ++ return reg; ++} ++ ++/* ++ * Probe SPI flash device ++ * Function returns 0 for failure. ++ * and flashconfig_tbl array index for success. ++ */ ++static int ++spiflash_probe_chip(struct platform_device *pdev, struct spiflash_priv *priv) ++{ ++ u32 sig = spiflash_sendcmd(priv, SPI_RD_SIG, 0); ++ int flash_size; ++ ++ switch (sig) { ++ case STM_8MBIT_SIGNATURE: ++ flash_size = FLASH_1MB; ++ break; ++ case STM_16MBIT_SIGNATURE: ++ flash_size = FLASH_2MB; ++ break; ++ case STM_32MBIT_SIGNATURE: ++ flash_size = FLASH_4MB; ++ break; ++ case STM_64MBIT_SIGNATURE: ++ flash_size = FLASH_8MB; ++ break; ++ case STM_128MBIT_SIGNATURE: ++ flash_size = FLASH_16MB; ++ break; ++ default: ++ dev_warn(&pdev->dev, "read of flash device signature failed!\n"); ++ return 0; ++ } ++ ++ return flash_size; ++} ++ ++static void ++spiflash_wait_complete(struct spiflash_priv *priv, unsigned int timeout) ++{ ++ busy_wait(priv, spiflash_sendcmd(priv, SPI_RD_STATUS, 0) & ++ SPI_STATUS_WIP, timeout); ++} ++ ++static int ++spiflash_erase(struct mtd_info *mtd, struct erase_info *instr) ++{ ++ struct spiflash_priv *priv = to_spiflash(mtd); ++ const struct opcodes *op; ++ u32 temp, reg; ++ ++ if (instr->addr + instr->len > mtd->size) ++ return -EINVAL; ++ ++ mutex_lock(&priv->lock); ++ ++ spiflash_sendcmd(priv, SPI_WRITE_ENABLE, 0); ++ reg = spiflash_wait_busy(priv); ++ ++ op = &stm_opcodes[SPI_SECTOR_ERASE]; ++ temp = ((u32)instr->addr << 8) | (u32)(op->code); ++ spiflash_write_reg(priv, SPI_FLASH_OPCODE, temp); ++ ++ reg &= ~SPI_CTL_TX_RX_CNT_MASK; ++ reg |= op->tx_cnt | SPI_CTL_START; ++ spiflash_write_reg(priv, SPI_FLASH_CTL, reg); ++ ++ spiflash_wait_complete(priv, 20); ++ ++ mutex_unlock(&priv->lock); ++ ++ instr->state = MTD_ERASE_DONE; ++ mtd_erase_callback(instr); ++ ++ return 0; ++} ++ ++static int ++spiflash_read(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, ++ u_char *buf) ++{ ++ struct spiflash_priv *priv = to_spiflash(mtd); ++ ++ if (!len) ++ return 0; ++ ++ if (from + len > mtd->size) ++ return -EINVAL; ++ ++ *retlen = len; ++ ++ mutex_lock(&priv->lock); ++ ++ memcpy_fromio(buf, priv->readaddr + from, len); ++ ++ mutex_unlock(&priv->lock); ++ ++ return 0; ++} ++ ++static int ++spiflash_write(struct mtd_info *mtd, loff_t to, size_t len, size_t *retlen, ++ const u8 *buf) ++{ ++ struct spiflash_priv *priv = to_spiflash(mtd); ++ u32 opcode, bytes_left; ++ ++ *retlen = 0; ++ ++ if (!len) ++ return 0; ++ ++ if (to + len > mtd->size) ++ return -EINVAL; ++ ++ bytes_left = len; ++ ++ do { ++ u32 read_len, reg, page_offset, spi_data = 0; ++ ++ read_len = min(bytes_left, sizeof(u32)); ++ ++ /* 32-bit writes cannot span across a page boundary ++ * (256 bytes). This types of writes require two page ++ * program operations to handle it correctly. The STM part ++ * will write the overflow data to the beginning of the ++ * current page as opposed to the subsequent page. ++ */ ++ page_offset = (to & (STM_PAGE_SIZE - 1)) + read_len; ++ ++ if (page_offset > STM_PAGE_SIZE) ++ read_len -= (page_offset - STM_PAGE_SIZE); ++ ++ mutex_lock(&priv->lock); ++ ++ spiflash_sendcmd(priv, SPI_WRITE_ENABLE, 0); ++ spi_data = 0; ++ switch (read_len) { ++ case 4: ++ spi_data |= buf[3] << 24; ++ /* fall through */ ++ case 3: ++ spi_data |= buf[2] << 16; ++ /* fall through */ ++ case 2: ++ spi_data |= buf[1] << 8; ++ /* fall through */ ++ case 1: ++ spi_data |= buf[0] & 0xff; ++ break; ++ default: ++ break; ++ } ++ ++ spiflash_write_reg(priv, SPI_FLASH_DATA, spi_data); ++ opcode = stm_opcodes[SPI_PAGE_PROGRAM].code | ++ (to & 0x00ffffff) << 8; ++ spiflash_write_reg(priv, SPI_FLASH_OPCODE, opcode); ++ ++ reg = spiflash_read_reg(priv, SPI_FLASH_CTL); ++ reg &= ~SPI_CTL_TX_RX_CNT_MASK; ++ reg |= (read_len + 4) | SPI_CTL_START; ++ spiflash_write_reg(priv, SPI_FLASH_CTL, reg); ++ ++ spiflash_wait_complete(priv, 1); ++ ++ mutex_unlock(&priv->lock); ++ ++ bytes_left -= read_len; ++ to += read_len; ++ buf += read_len; ++ ++ *retlen += read_len; ++ } while (bytes_left != 0); ++ ++ return 0; ++} ++ ++#if defined CONFIG_MTD_REDBOOT_PARTS || CONFIG_MTD_MYLOADER_PARTS ++static const char * const part_probe_types[] = { ++ "cmdlinepart", "RedBoot", "MyLoader", NULL ++}; ++#endif ++ ++static int ++spiflash_probe(struct platform_device *pdev) ++{ ++ struct spiflash_priv *priv; ++ struct mtd_info *mtd; ++ struct resource *res; ++ int index; ++ int result = 0; ++ ++ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); ++ if (!priv) ++ return -ENOMEM; ++ ++ mutex_init(&priv->lock); ++ mtd = &priv->mtd; ++ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 1); ++ priv->mmraddr = devm_ioremap_resource(&pdev->dev, res); ++ if (IS_ERR(priv->mmraddr)) { ++ dev_warn(&pdev->dev, "failed to map flash MMR\n"); ++ return PTR_ERR(priv->mmraddr); ++ } ++ ++ index = spiflash_probe_chip(pdev, priv); ++ if (!index) { ++ dev_warn(&pdev->dev, "found no flash device\n"); ++ return -ENODEV; ++ } ++ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ priv->readaddr = devm_ioremap_resource(&pdev->dev, res); ++ if (IS_ERR(priv->readaddr)) { ++ dev_warn(&pdev->dev, "failed to map flash read mem\n"); ++ return PTR_ERR(priv->readaddr); ++ } ++ ++ platform_set_drvdata(pdev, priv); ++ mtd->name = "spiflash"; ++ mtd->type = MTD_NORFLASH; ++ mtd->flags = (MTD_CAP_NORFLASH|MTD_WRITEABLE); ++ mtd->size = flashconfig_tbl[index].byte_cnt; ++ mtd->erasesize = flashconfig_tbl[index].sector_size; ++ mtd->writesize = 1; ++ mtd->numeraseregions = 0; ++ mtd->eraseregions = NULL; ++ mtd->_erase = spiflash_erase; ++ mtd->_read = spiflash_read; ++ mtd->_write = spiflash_write; ++ mtd->owner = THIS_MODULE; ++ ++ dev_info(&pdev->dev, "%lld Kbytes flash detected\n", mtd->size >> 10); ++ ++#if defined CONFIG_MTD_REDBOOT_PARTS || CONFIG_MTD_MYLOADER_PARTS ++ /* parse redboot partitions */ ++ ++ result = mtd_device_parse_register(mtd, part_probe_types, ++ NULL, NULL, 0); ++#endif ++ ++ return result; ++} ++ ++static int ++spiflash_remove(struct platform_device *pdev) ++{ ++ struct spiflash_priv *priv = platform_get_drvdata(pdev); ++ ++ mtd_device_unregister(&priv->mtd); ++ ++ return 0; ++} ++ ++static struct platform_driver spiflash_driver = { ++ .driver.name = DRIVER_NAME, ++ .probe = spiflash_probe, ++ .remove = spiflash_remove, ++}; ++ ++module_platform_driver(spiflash_driver); ++ ++MODULE_LICENSE("GPL"); ++MODULE_AUTHOR("OpenWrt.org"); ++MODULE_AUTHOR("Atheros Communications Inc"); ++MODULE_DESCRIPTION("MTD driver for SPI Flash on Atheros AR2315+ SOC"); ++MODULE_ALIAS("platform:" DRIVER_NAME); ++ +--- /dev/null ++++ b/drivers/mtd/devices/ar2315_spiflash.h +@@ -0,0 +1,106 @@ ++/* ++ * Atheros AR2315 SPI Flash Memory support header file. ++ * ++ * Copyright (c) 2005, Atheros Communications Inc. ++ * Copyright (C) 2006 FON Technology, SL. ++ * Copyright (C) 2006 Imre Kaloz ++ * Copyright (C) 2006-2009 Felix Fietkau ++ * ++ * This code is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++#ifndef __AR2315_SPIFLASH_H ++#define __AR2315_SPIFLASH_H ++ ++#define STM_PAGE_SIZE 256 ++ ++#define SFI_WRITE_BUFFER_SIZE 4 ++#define SFI_FLASH_ADDR_MASK 0x00ffffff ++ ++#define STM_8MBIT_SIGNATURE 0x13 ++#define STM_M25P80_BYTE_COUNT 1048576 ++#define STM_M25P80_SECTOR_COUNT 16 ++#define STM_M25P80_SECTOR_SIZE 0x10000 ++ ++#define STM_16MBIT_SIGNATURE 0x14 ++#define STM_M25P16_BYTE_COUNT 2097152 ++#define STM_M25P16_SECTOR_COUNT 32 ++#define STM_M25P16_SECTOR_SIZE 0x10000 ++ ++#define STM_32MBIT_SIGNATURE 0x15 ++#define STM_M25P32_BYTE_COUNT 4194304 ++#define STM_M25P32_SECTOR_COUNT 64 ++#define STM_M25P32_SECTOR_SIZE 0x10000 ++ ++#define STM_64MBIT_SIGNATURE 0x16 ++#define STM_M25P64_BYTE_COUNT 8388608 ++#define STM_M25P64_SECTOR_COUNT 128 ++#define STM_M25P64_SECTOR_SIZE 0x10000 ++ ++#define STM_128MBIT_SIGNATURE 0x17 ++#define STM_M25P128_BYTE_COUNT 16777216 ++#define STM_M25P128_SECTOR_COUNT 256 ++#define STM_M25P128_SECTOR_SIZE 0x10000 ++ ++#define STM_1MB_BYTE_COUNT STM_M25P80_BYTE_COUNT ++#define STM_1MB_SECTOR_COUNT STM_M25P80_SECTOR_COUNT ++#define STM_1MB_SECTOR_SIZE STM_M25P80_SECTOR_SIZE ++#define STM_2MB_BYTE_COUNT STM_M25P16_BYTE_COUNT ++#define STM_2MB_SECTOR_COUNT STM_M25P16_SECTOR_COUNT ++#define STM_2MB_SECTOR_SIZE STM_M25P16_SECTOR_SIZE ++#define STM_4MB_BYTE_COUNT STM_M25P32_BYTE_COUNT ++#define STM_4MB_SECTOR_COUNT STM_M25P32_SECTOR_COUNT ++#define STM_4MB_SECTOR_SIZE STM_M25P32_SECTOR_SIZE ++#define STM_8MB_BYTE_COUNT STM_M25P64_BYTE_COUNT ++#define STM_8MB_SECTOR_COUNT STM_M25P64_SECTOR_COUNT ++#define STM_8MB_SECTOR_SIZE STM_M25P64_SECTOR_SIZE ++#define STM_16MB_BYTE_COUNT STM_M25P128_BYTE_COUNT ++#define STM_16MB_SECTOR_COUNT STM_M25P128_SECTOR_COUNT ++#define STM_16MB_SECTOR_SIZE STM_M25P128_SECTOR_SIZE ++ ++/* ++ * ST Microelectronics Opcodes for Serial Flash ++ */ ++ ++#define STM_OP_WR_ENABLE 0x06 /* Write Enable */ ++#define STM_OP_WR_DISABLE 0x04 /* Write Disable */ ++#define STM_OP_RD_STATUS 0x05 /* Read Status */ ++#define STM_OP_WR_STATUS 0x01 /* Write Status */ ++#define STM_OP_RD_DATA 0x03 /* Read Data */ ++#define STM_OP_FAST_RD_DATA 0x0b /* Fast Read Data */ ++#define STM_OP_PAGE_PGRM 0x02 /* Page Program */ ++#define STM_OP_SECTOR_ERASE 0xd8 /* Sector Erase */ ++#define STM_OP_BULK_ERASE 0xc7 /* Bulk Erase */ ++#define STM_OP_DEEP_PWRDOWN 0xb9 /* Deep Power-Down Mode */ ++#define STM_OP_RD_SIG 0xab /* Read Electronic Signature */ ++ ++#define STM_STATUS_WIP 0x01 /* Write-In-Progress */ ++#define STM_STATUS_WEL 0x02 /* Write Enable Latch */ ++#define STM_STATUS_BP0 0x04 /* Block Protect 0 */ ++#define STM_STATUS_BP1 0x08 /* Block Protect 1 */ ++#define STM_STATUS_BP2 0x10 /* Block Protect 2 */ ++#define STM_STATUS_SRWD 0x80 /* Status Register Write Disable */ ++ ++/* ++ * SPI Flash Interface Registers ++ */ ++ ++#define SPI_FLASH_CTL 0x00 ++#define SPI_FLASH_OPCODE 0x04 ++#define SPI_FLASH_DATA 0x08 ++ ++#define SPI_CTL_START 0x00000100 ++#define SPI_CTL_BUSY 0x00010000 ++#define SPI_CTL_TXCNT_MASK 0x0000000f ++#define SPI_CTL_RXCNT_MASK 0x000000f0 ++#define SPI_CTL_TX_RX_CNT_MASK 0x000000ff ++#define SPI_CTL_SIZE_MASK 0x00060000 ++ ++#define SPI_CTL_CLK_SEL_MASK 0x03000000 ++#define SPI_OPCODE_MASK 0x000000ff ++ ++#define SPI_STATUS_WIP STM_STATUS_WIP ++ ++#endif +--- a/arch/mips/ath25/ar2315.c ++++ b/arch/mips/ath25/ar2315.c +@@ -220,6 +220,28 @@ static struct platform_device ar2315_gpi + .num_resources = ARRAY_SIZE(ar2315_gpio_res) + }; + ++static struct resource ar2315_spiflash_res[] = { ++ { ++ .name = "spiflash_read", ++ .flags = IORESOURCE_MEM, ++ .start = AR2315_SPI_READ_BASE, ++ .end = AR2315_SPI_READ_BASE + AR2315_SPI_READ_SIZE - 1, ++ }, ++ { ++ .name = "spiflash_mmr", ++ .flags = IORESOURCE_MEM, ++ .start = AR2315_SPI_MMR_BASE, ++ .end = AR2315_SPI_MMR_BASE + AR2315_SPI_MMR_SIZE - 1, ++ }, ++}; ++ ++static struct platform_device ar2315_spiflash = { ++ .id = 0, ++ .name = "ar2315-spiflash", ++ .resource = ar2315_spiflash_res, ++ .num_resources = ARRAY_SIZE(ar2315_spiflash_res) ++}; ++ + void __init ar2315_init_devices(void) + { + /* Find board configuration */ +@@ -230,6 +252,8 @@ void __init ar2315_init_devices(void) + ar2315_gpio_res[1].end = ar2315_gpio_res[1].start; + platform_device_register(&ar2315_gpio); + ++ platform_device_register(&ar2315_spiflash); ++ + ar2315_eth_data.macaddr = ath25_board.config->enet0_mac; + ath25_add_ethernet(0, AR2315_ENET0_BASE, "eth0_mii", + AR2315_ENET0_MII_BASE, AR2315_IRQ_ENET0, diff --git a/target/linux/ath25/patches-4.9/130-watchdog.patch b/target/linux/ath25/patches-4.9/130-watchdog.patch new file mode 100644 index 0000000000..fef3ac098a --- /dev/null +++ b/target/linux/ath25/patches-4.9/130-watchdog.patch @@ -0,0 +1,277 @@ +--- /dev/null ++++ b/drivers/watchdog/ar2315-wtd.c +@@ -0,0 +1,209 @@ ++/* ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License as published by ++ * the Free Software Foundation; either version 2 of the License, or ++ * (at your option) any later version. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, see . ++ * ++ * Copyright (C) 2008 John Crispin ++ * Based on EP93xx and ifxmips wdt driver ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define DRIVER_NAME "ar2315-wdt" ++ ++#define CLOCK_RATE 40000000 ++#define HEARTBEAT(x) (x < 1 || x > 90 ? 20 : x) ++ ++#define WDT_REG_TIMER 0x00 ++#define WDT_REG_CTRL 0x04 ++ ++#define WDT_CTRL_ACT_NONE 0x00000000 /* No action */ ++#define WDT_CTRL_ACT_NMI 0x00000001 /* NMI on watchdog */ ++#define WDT_CTRL_ACT_RESET 0x00000002 /* reset on watchdog */ ++ ++static int wdt_timeout = 20; ++static int started; ++static int in_use; ++static void __iomem *wdt_base; ++ ++static inline void ar2315_wdt_wr(unsigned reg, u32 val) ++{ ++ iowrite32(val, wdt_base + reg); ++} ++ ++static void ++ar2315_wdt_enable(void) ++{ ++ ar2315_wdt_wr(WDT_REG_TIMER, wdt_timeout * CLOCK_RATE); ++} ++ ++static ssize_t ++ar2315_wdt_write(struct file *file, const char __user *data, size_t len, ++ loff_t *ppos) ++{ ++ if (len) ++ ar2315_wdt_enable(); ++ return len; ++} ++ ++static int ++ar2315_wdt_open(struct inode *inode, struct file *file) ++{ ++ if (in_use) ++ return -EBUSY; ++ ar2315_wdt_enable(); ++ in_use = 1; ++ started = 1; ++ return nonseekable_open(inode, file); ++} ++ ++static int ++ar2315_wdt_release(struct inode *inode, struct file *file) ++{ ++ in_use = 0; ++ return 0; ++} ++ ++static irqreturn_t ++ar2315_wdt_interrupt(int irq, void *dev) ++{ ++ struct platform_device *pdev = (struct platform_device *)dev; ++ ++ if (started) { ++ dev_crit(&pdev->dev, "watchdog expired, rebooting system\n"); ++ emergency_restart(); ++ } else { ++ ar2315_wdt_wr(WDT_REG_CTRL, 0); ++ ar2315_wdt_wr(WDT_REG_TIMER, 0); ++ } ++ return IRQ_HANDLED; ++} ++ ++static struct watchdog_info ident = { ++ .options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING, ++ .identity = "ar2315 Watchdog", ++}; ++ ++static long ++ar2315_wdt_ioctl(struct file *file, unsigned int cmd, unsigned long arg) ++{ ++ int new_wdt_timeout; ++ int ret = -ENOIOCTLCMD; ++ ++ switch (cmd) { ++ case WDIOC_GETSUPPORT: ++ ret = copy_to_user((void __user *)arg, &ident, sizeof(ident)) ? ++ -EFAULT : 0; ++ break; ++ case WDIOC_KEEPALIVE: ++ ar2315_wdt_enable(); ++ ret = 0; ++ break; ++ case WDIOC_SETTIMEOUT: ++ ret = get_user(new_wdt_timeout, (int __user *)arg); ++ if (ret) ++ break; ++ wdt_timeout = HEARTBEAT(new_wdt_timeout); ++ ar2315_wdt_enable(); ++ break; ++ case WDIOC_GETTIMEOUT: ++ ret = put_user(wdt_timeout, (int __user *)arg); ++ break; ++ } ++ return ret; ++} ++ ++static const struct file_operations ar2315_wdt_fops = { ++ .owner = THIS_MODULE, ++ .llseek = no_llseek, ++ .write = ar2315_wdt_write, ++ .unlocked_ioctl = ar2315_wdt_ioctl, ++ .open = ar2315_wdt_open, ++ .release = ar2315_wdt_release, ++}; ++ ++static struct miscdevice ar2315_wdt_miscdev = { ++ .minor = WATCHDOG_MINOR, ++ .name = "watchdog", ++ .fops = &ar2315_wdt_fops, ++}; ++ ++static int ++ar2315_wdt_probe(struct platform_device *dev) ++{ ++ struct resource *mem_res, *irq_res; ++ int ret = 0; ++ ++ if (wdt_base) ++ return -EBUSY; ++ ++ irq_res = platform_get_resource(dev, IORESOURCE_IRQ, 0); ++ if (!irq_res) { ++ dev_err(&dev->dev, "no IRQ resource\n"); ++ return -ENOENT; ++ } ++ ++ mem_res = platform_get_resource(dev, IORESOURCE_MEM, 0); ++ wdt_base = devm_ioremap_resource(&dev->dev, mem_res); ++ if (IS_ERR(wdt_base)) ++ return PTR_ERR(wdt_base); ++ ++ ret = devm_request_irq(&dev->dev, irq_res->start, ar2315_wdt_interrupt, ++ 0, DRIVER_NAME, dev); ++ if (ret) { ++ dev_err(&dev->dev, "failed to register inetrrupt\n"); ++ goto out; ++ } ++ ++ ret = misc_register(&ar2315_wdt_miscdev); ++ if (ret) ++ dev_err(&dev->dev, "failed to register miscdev\n"); ++ ++out: ++ return ret; ++} ++ ++static int ++ar2315_wdt_remove(struct platform_device *dev) ++{ ++ misc_deregister(&ar2315_wdt_miscdev); ++ return 0; ++} ++ ++static struct platform_driver ar2315_wdt_driver = { ++ .probe = ar2315_wdt_probe, ++ .remove = ar2315_wdt_remove, ++ .driver = { ++ .name = DRIVER_NAME, ++ .owner = THIS_MODULE, ++ }, ++}; ++ ++module_platform_driver(ar2315_wdt_driver); ++ ++MODULE_DESCRIPTION("Atheros AR2315 hardware watchdog driver"); ++MODULE_AUTHOR("John Crispin "); ++MODULE_LICENSE("GPL"); ++MODULE_ALIAS("platform:" DRIVER_NAME); +--- a/drivers/watchdog/Kconfig ++++ b/drivers/watchdog/Kconfig +@@ -1554,6 +1554,13 @@ config PIC32_DMT + To compile this driver as a loadable module, choose M here. + The module will be called pic32-dmt. + ++config AR2315_WDT ++ tristate "Atheros AR2315+ WiSoCs Watchdog Timer" ++ depends on ATH25 ++ help ++ Hardware driver for the built-in watchdog timer on the Atheros ++ AR2315/AR2316 WiSoCs. ++ + # PARISC Architecture + + # POWERPC Architecture +--- a/drivers/watchdog/Makefile ++++ b/drivers/watchdog/Makefile +@@ -159,6 +159,7 @@ obj-$(CONFIG_WDT_MTX1) += mtx-1_wdt.o + obj-$(CONFIG_PNX833X_WDT) += pnx833x_wdt.o + obj-$(CONFIG_SIBYTE_WDOG) += sb_wdog.o + obj-$(CONFIG_AR7_WDT) += ar7_wdt.o ++obj-$(CONFIG_AR2315_WDT) += ar2315-wtd.o + obj-$(CONFIG_TXX9_WDT) += txx9wdt.o + obj-$(CONFIG_OCTEON_WDT) += octeon-wdt.o + octeon-wdt-y := octeon-wdt-main.o octeon-wdt-nmi.o +--- a/arch/mips/ath25/ar2315.c ++++ b/arch/mips/ath25/ar2315.c +@@ -220,6 +220,24 @@ static struct platform_device ar2315_gpi + .num_resources = ARRAY_SIZE(ar2315_gpio_res) + }; + ++static struct resource ar2315_wdt_res[] = { ++ { ++ .flags = IORESOURCE_MEM, ++ .start = AR2315_RST_BASE + AR2315_WDT_TIMER, ++ .end = AR2315_RST_BASE + AR2315_WDT_TIMER + 8 - 1, ++ }, ++ { ++ .flags = IORESOURCE_IRQ, ++ } ++}; ++ ++static struct platform_device ar2315_wdt = { ++ .id = 0, ++ .name = "ar2315-wdt", ++ .resource = ar2315_wdt_res, ++ .num_resources = ARRAY_SIZE(ar2315_wdt_res) ++}; ++ + static struct resource ar2315_spiflash_res[] = { + { + .name = "spiflash_read", +@@ -252,6 +270,11 @@ void __init ar2315_init_devices(void) + ar2315_gpio_res[1].end = ar2315_gpio_res[1].start; + platform_device_register(&ar2315_gpio); + ++ ar2315_wdt_res[1].start = irq_create_mapping(ar2315_misc_irq_domain, ++ AR2315_MISC_IRQ_WATCHDOG); ++ ar2315_wdt_res[1].end = ar2315_wdt_res[1].start; ++ platform_device_register(&ar2315_wdt); ++ + platform_device_register(&ar2315_spiflash); + + ar2315_eth_data.macaddr = ath25_board.config->enet0_mac; diff --git a/target/linux/ath25/patches-4.9/140-redboot_boardconfig.patch b/target/linux/ath25/patches-4.9/140-redboot_boardconfig.patch new file mode 100644 index 0000000000..6aad761cb1 --- /dev/null +++ b/target/linux/ath25/patches-4.9/140-redboot_boardconfig.patch @@ -0,0 +1,60 @@ +--- a/drivers/mtd/redboot.c ++++ b/drivers/mtd/redboot.c +@@ -30,6 +30,8 @@ + #include + #include + ++#define BOARD_CONFIG_PART "boardconfig" ++ + struct fis_image_desc { + unsigned char name[16]; // Null terminated name + uint32_t flash_base; // Address within FLASH of image +@@ -60,6 +62,7 @@ static int parse_redboot_partitions(stru + const struct mtd_partition **pparts, + struct mtd_part_parser_data *data) + { ++ unsigned long max_offset = 0; + int nrparts = 0; + struct fis_image_desc *buf; + struct mtd_partition *parts; +@@ -225,14 +228,15 @@ static int parse_redboot_partitions(stru + } + } + #endif +- parts = kzalloc(sizeof(*parts)*nrparts + nulllen + namelen, GFP_KERNEL); ++ parts = kzalloc(sizeof(*parts) * (nrparts + 1) + nulllen + namelen + ++ sizeof(BOARD_CONFIG_PART), GFP_KERNEL); + + if (!parts) { + ret = -ENOMEM; + goto out; + } + +- nullname = (char *)&parts[nrparts]; ++ nullname = (char *)&parts[nrparts + 1]; + #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED + if (nulllen > 0) { + strcpy(nullname, nullstring); +@@ -251,6 +255,8 @@ static int parse_redboot_partitions(stru + } + #endif + for ( ; iimg->size; + parts[i].offset = fl->img->flash_base; + parts[i].name = names; +@@ -284,6 +290,13 @@ static int parse_redboot_partitions(stru + fl = fl->next; + kfree(tmp_fl); + } ++ if (master->size - max_offset >= master->erasesize) { ++ parts[nrparts].size = master->size - max_offset; ++ parts[nrparts].offset = max_offset; ++ parts[nrparts].name = names; ++ strcpy(names, BOARD_CONFIG_PART); ++ nrparts++; ++ } + ret = nrparts; + *pparts = parts; + out: diff --git a/target/linux/ath25/patches-4.9/141-redboot_partition_scan.patch b/target/linux/ath25/patches-4.9/141-redboot_partition_scan.patch new file mode 100644 index 0000000000..d1d281eaf4 --- /dev/null +++ b/target/linux/ath25/patches-4.9/141-redboot_partition_scan.patch @@ -0,0 +1,44 @@ +--- a/drivers/mtd/redboot.c ++++ b/drivers/mtd/redboot.c +@@ -79,12 +79,18 @@ static int parse_redboot_partitions(stru + static char nullstring[] = "unallocated"; + #endif + ++ buf = vmalloc(master->erasesize); ++ if (!buf) ++ return -ENOMEM; ++ ++ restart: + if ( directory < 0 ) { + offset = master->size + directory * master->erasesize; + while (mtd_block_isbad(master, offset)) { + if (!offset) { + nogood: + printk(KERN_NOTICE "Failed to find a non-bad block to check for RedBoot partition table\n"); ++ vfree(buf); + return -EIO; + } + offset -= master->erasesize; +@@ -97,10 +103,6 @@ static int parse_redboot_partitions(stru + goto nogood; + } + } +- buf = vmalloc(master->erasesize); +- +- if (!buf) +- return -ENOMEM; + + printk(KERN_NOTICE "Searching for RedBoot partition table in %s at offset 0x%lx\n", + master->name, offset); +@@ -173,6 +175,11 @@ static int parse_redboot_partitions(stru + } + if (i == numslots) { + /* Didn't find it */ ++ if (offset + master->erasesize < master->size) { ++ /* not at the end of the flash yet, maybe next block */ ++ directory++; ++ goto restart; ++ } + printk(KERN_NOTICE "No RedBoot partition table detected in %s\n", + master->name); + ret = 0; diff --git a/target/linux/ath25/patches-4.9/142-redboot_various_erase_size_fix.patch b/target/linux/ath25/patches-4.9/142-redboot_various_erase_size_fix.patch new file mode 100644 index 0000000000..ce039df9f1 --- /dev/null +++ b/target/linux/ath25/patches-4.9/142-redboot_various_erase_size_fix.patch @@ -0,0 +1,72 @@ +--- a/drivers/mtd/redboot.c ++++ b/drivers/mtd/redboot.c +@@ -58,6 +58,22 @@ static inline int redboot_checksum(struc + return 1; + } + ++static uint32_t mtd_get_offset_erasesize(struct mtd_info *mtd, uint64_t offset) ++{ ++ struct mtd_erase_region_info *regions = mtd->eraseregions; ++ int i; ++ ++ for (i = 0; i < mtd->numeraseregions; i++) { ++ if (regions[i].offset + ++ regions[i].numblocks * regions[i].erasesize <= offset) ++ continue; ++ ++ return regions[i].erasesize; ++ } ++ ++ return mtd->erasesize; ++} ++ + static int parse_redboot_partitions(struct mtd_info *master, + const struct mtd_partition **pparts, + struct mtd_part_parser_data *data) +@@ -74,6 +90,7 @@ static int parse_redboot_partitions(stru + int namelen = 0; + int nulllen = 0; + int numslots; ++ int first_slot; + unsigned long offset; + #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED + static char nullstring[] = "unallocated"; +@@ -186,7 +203,10 @@ static int parse_redboot_partitions(stru + goto out; + } + +- for (i = 0; i < numslots; i++) { ++ first_slot = (buf[i].flash_base & (master->erasesize - 1)) / ++ sizeof(struct fis_image_desc); ++ ++ for (i = first_slot; i < first_slot + numslots; i++) { + struct fis_list *new_fl, **prev; + + if (buf[i].name[0] == 0xff) { +@@ -262,12 +282,13 @@ static int parse_redboot_partitions(stru + } + #endif + for ( ; iimg->size; + parts[i].offset = fl->img->flash_base; + parts[i].name = names; + ++ if (max_offset < parts[i].offset + parts[i].size) ++ max_offset = parts[i].offset + parts[i].size; ++ + strcpy(names, fl->img->name); + #ifdef CONFIG_MTD_REDBOOT_PARTS_READONLY + if (!memcmp(names, "RedBoot", 8) || +@@ -297,7 +318,9 @@ static int parse_redboot_partitions(stru + fl = fl->next; + kfree(tmp_fl); + } +- if (master->size - max_offset >= master->erasesize) { ++ ++ if (master->size - max_offset >= ++ mtd_get_offset_erasesize(master, max_offset)) { + parts[nrparts].size = master->size - max_offset; + parts[nrparts].offset = max_offset; + parts[nrparts].name = names; diff --git a/target/linux/ath25/patches-4.9/210-reset_button.patch b/target/linux/ath25/patches-4.9/210-reset_button.patch new file mode 100644 index 0000000000..34ef46bc52 --- /dev/null +++ b/target/linux/ath25/patches-4.9/210-reset_button.patch @@ -0,0 +1,71 @@ +--- a/arch/mips/ath25/Makefile ++++ b/arch/mips/ath25/Makefile +@@ -8,7 +8,7 @@ + # Copyright (C) 2006-2009 Felix Fietkau + # + +-obj-y += board.o prom.o devices.o ++obj-y += board.o prom.o devices.o reset.o + + obj-$(CONFIG_EARLY_PRINTK) += early_printk.o + +--- /dev/null ++++ b/arch/mips/ath25/reset.c +@@ -0,0 +1,57 @@ ++#include ++#include ++#include ++#include ++#include ++#include ++#include "devices.h" ++ ++static int __init ++ar231x_init_reset(void) ++{ ++ struct platform_device *pdev; ++ struct gpio_keys_platform_data pdata; ++ struct gpio_keys_button *p; ++ int err; ++ ++ if (ath25_board.config->reset_config_gpio == 0xffff) ++ return -ENODEV; ++ ++ p = kzalloc(sizeof(*p), GFP_KERNEL); ++ if (!p) ++ goto err; ++ ++ p->desc = "reset"; ++ p->type = EV_KEY; ++ p->code = KEY_RESTART; ++ p->debounce_interval = 60; ++ p->gpio = ath25_board.config->reset_config_gpio; ++ ++ memset(&pdata, 0, sizeof(pdata)); ++ pdata.poll_interval = 20; ++ pdata.buttons = p; ++ pdata.nbuttons = 1; ++ ++ pdev = platform_device_alloc("gpio-keys-polled", 0); ++ if (!pdev) ++ goto err_free; ++ ++ err = platform_device_add_data(pdev, &pdata, sizeof(pdata)); ++ if (err) ++ goto err_put_pdev; ++ ++ err = platform_device_add(pdev); ++ if (err) ++ goto err_put_pdev; ++ ++ return 0; ++ ++err_put_pdev: ++ platform_device_put(pdev); ++err_free: ++ kfree(p); ++err: ++ return -ENOMEM; ++} ++ ++module_init(ar231x_init_reset); diff --git a/target/linux/ath25/patches-4.9/220-enet_micrel_workaround.patch b/target/linux/ath25/patches-4.9/220-enet_micrel_workaround.patch new file mode 100644 index 0000000000..398495a80c --- /dev/null +++ b/target/linux/ath25/patches-4.9/220-enet_micrel_workaround.patch @@ -0,0 +1,91 @@ +--- a/drivers/net/ethernet/atheros/ar231x/ar231x.c ++++ b/drivers/net/ethernet/atheros/ar231x/ar231x.c +@@ -135,6 +135,7 @@ static int ar231x_mdiobus_write(struct m + static int ar231x_mdiobus_reset(struct mii_bus *bus); + static int ar231x_mdiobus_probe(struct net_device *dev); + static void ar231x_adjust_link(struct net_device *dev); ++static bool no_phy; + + #ifndef ERR + #define ERR(fmt, args...) printk("%s: " fmt, __func__, ##args) +@@ -167,6 +168,32 @@ static const struct net_device_ops ar231 + #endif + }; + ++static int get_phy_id(struct mii_bus *bus, int addr, u32 *phy_id) ++{ ++ int phy_reg; ++ ++ /** ++ * Grab the bits from PHYIR1, and put them ++ * in the upper half. ++ */ ++ phy_reg = mdiobus_read(bus, addr, MII_PHYSID1); ++ ++ if (phy_reg < 0) ++ return -EIO; ++ ++ *phy_id = (phy_reg & 0xffff) << 16; ++ ++ /* Grab the bits from PHYIR2, and put them in the lower half */ ++ phy_reg = mdiobus_read(bus, addr, MII_PHYSID2); ++ ++ if (phy_reg < 0) ++ return -EIO; ++ ++ *phy_id |= (phy_reg & 0xffff); ++ ++ return 0; ++} ++ + static int ar231x_probe(struct platform_device *pdev) + { + struct net_device *dev; +@@ -273,6 +300,24 @@ static int ar231x_probe(struct platform_ + + mdiobus_register(sp->mii_bus); + ++ /** ++ * Workaround for Micrel switch, which is only available on ++ * one PHY and cannot be configured through MDIO. ++ */ ++ if (!no_phy) { ++ u32 phy_id = 0; ++ ++ get_phy_id(sp->mii_bus, 1, &phy_id); ++ if (phy_id == 0x00221450) ++ no_phy = true; ++ } ++ if (no_phy) { ++ sp->link = 1; ++ netif_carrier_on(dev); ++ return 0; ++ } ++ no_phy = true; ++ + if (ar231x_mdiobus_probe(dev) != 0) { + printk(KERN_ERR "%s: mdiobus_probe failed\n", dev->name); + rx_tasklet_cleanup(dev); +@@ -329,8 +374,10 @@ static int ar231x_remove(struct platform + rx_tasklet_cleanup(dev); + ar231x_init_cleanup(dev); + unregister_netdev(dev); +- mdiobus_unregister(sp->mii_bus); +- mdiobus_free(sp->mii_bus); ++ if (sp->mii_bus) { ++ mdiobus_unregister(sp->mii_bus); ++ mdiobus_free(sp->mii_bus); ++ } + kfree(dev); + return 0; + } +@@ -1079,6 +1126,9 @@ static int ar231x_ioctl(struct net_devic + { + struct ar231x_private *sp = netdev_priv(dev); + ++ if (!sp->phy_dev) ++ return -ENODEV; ++ + switch (cmd) { + case SIOCGMIIPHY: + case SIOCGMIIREG: diff --git a/target/linux/ath25/patches-4.9/330-board_leds.patch b/target/linux/ath25/patches-4.9/330-board_leds.patch new file mode 100644 index 0000000000..e357fc6a64 --- /dev/null +++ b/target/linux/ath25/patches-4.9/330-board_leds.patch @@ -0,0 +1,116 @@ +--- a/arch/mips/ath25/ar2315.c ++++ b/arch/mips/ath25/ar2315.c +@@ -23,6 +23,7 @@ + #include + #include + #include ++#include + #include + #include + #include +@@ -260,6 +261,50 @@ static struct platform_device ar2315_spi + .num_resources = ARRAY_SIZE(ar2315_spiflash_res) + }; + ++#ifdef CONFIG_LEDS_GPIO ++static struct gpio_led ar2315_leds[6]; ++static struct gpio_led_platform_data ar2315_led_data = { ++ .leds = (void *)ar2315_leds, ++}; ++ ++static struct platform_device ar2315_gpio_leds = { ++ .name = "leds-gpio", ++ .id = -1, ++ .dev = { ++ .platform_data = (void *)&ar2315_led_data, ++ } ++}; ++ ++static void __init ar2315_init_gpio_leds(void) ++{ ++ static char led_names[6][6]; ++ int i, led = 0; ++ ++ ar2315_led_data.num_leds = 0; ++ for (i = 1; i < 8; i++) { ++ if ((i == AR2315_RESET_GPIO) || ++ (i == ath25_board.config->reset_config_gpio)) ++ continue; ++ ++ if (i == ath25_board.config->sys_led_gpio) ++ strcpy(led_names[led], "wlan"); ++ else ++ sprintf(led_names[led], "gpio%d", i); ++ ++ ar2315_leds[led].name = led_names[led]; ++ ar2315_leds[led].gpio = i; ++ ar2315_leds[led].active_low = 0; ++ led++; ++ } ++ ar2315_led_data.num_leds = led; ++ platform_device_register(&ar2315_gpio_leds); ++} ++#else ++static inline void ar2315_init_gpio_leds(void) ++{ ++} ++#endif ++ + void __init ar2315_init_devices(void) + { + /* Find board configuration */ +@@ -270,6 +315,8 @@ void __init ar2315_init_devices(void) + ar2315_gpio_res[1].end = ar2315_gpio_res[1].start; + platform_device_register(&ar2315_gpio); + ++ ar2315_init_gpio_leds(); ++ + ar2315_wdt_res[1].start = irq_create_mapping(ar2315_misc_irq_domain, + AR2315_MISC_IRQ_WATCHDOG); + ar2315_wdt_res[1].end = ar2315_wdt_res[1].start; +--- a/arch/mips/ath25/ar5312.c ++++ b/arch/mips/ath25/ar5312.c +@@ -23,6 +23,7 @@ + #include + #include + #include ++#include + #include + #include + #include +@@ -231,6 +232,23 @@ static struct platform_device ar5312_gpi + .num_resources = ARRAY_SIZE(ar5312_gpio_res), + }; + ++#ifdef CONFIG_LEDS_GPIO ++static struct gpio_led ar5312_leds[] = { ++ { .name = "wlan", .gpio = 0, .active_low = 1, }, ++}; ++ ++static const struct gpio_led_platform_data ar5312_led_data = { ++ .num_leds = ARRAY_SIZE(ar5312_leds), ++ .leds = (void *)ar5312_leds, ++}; ++ ++static struct platform_device ar5312_gpio_leds = { ++ .name = "leds-gpio", ++ .id = -1, ++ .dev.platform_data = (void *)&ar5312_led_data, ++}; ++#endif ++ + static void __init ar5312_flash_init(void) + { + void __iomem *flashctl_base; +@@ -301,6 +319,11 @@ void __init ar5312_init_devices(void) + + platform_device_register(&ar5312_gpio); + ++#ifdef CONFIG_LEDS_GPIO ++ ar5312_leds[0].gpio = config->sys_led_gpio; ++ platform_device_register(&ar5312_gpio_leds); ++#endif ++ + /* Fix up MAC addresses if necessary */ + if (is_broadcast_ether_addr(config->enet0_mac)) + ether_addr_copy(config->enet0_mac, config->enet1_mac);