From: Sebastian Kemper Date: Sat, 1 Dec 2018 18:41:34 +0000 (+0100) Subject: ath79: add d-link dir-825-c1 and dir-835-a1 X-Git-Tag: v19.07.0-rc1~1863 X-Git-Url: http://git.openwrt.org/?p=openwrt%2Fopenwrt.git;a=commitdiff_plain;h=6c3c4436ee1af0742de7c29bd9c4f10990ed2019 ath79: add d-link dir-825-c1 and dir-835-a1 This commit ports both dir-825-c1 and dir-835-a1 from ar71xx to ath79. They're pretty much identical, except dir-835-a1 has less LEDs. The routers come with 128 MByte of RAM and 16 MBytes of flash and sport 2.4GHz and 5.0GHz wireless. Both routers have entries already in OpenWrt's TOH. Please check there for more information on these antiquities. https://openwrt.org/toh/hwdata/d-link/d-link_dir-825_c1 https://openwrt.org/toh/hwdata/d-link/d-link_dir-835_a1 Installation: 1. Connect to the web interface of the vendor firmware (usually listening on 192.168.0.1). 2. Go to "Tools", then "Firmware". 3. In the "Firmware Upgrade" box click "Browse". 4. Select the OpenWrt factory image for your router. 5. Click "Upload", confirm the popups if you agree to flash the file you selected. 6. Wait for firmware upgrade to complete. It takes about 5 minutes. Run-tested on dir-825-c1. dir-835-a1 should work as well, but I don't have this router so I can't confirm. Signed-off-by: Sebastian Kemper Signed-off-by: Christian Lamparter [trivial changes] --- diff --git a/include/image-commands.mk b/include/image-commands.mk index 63539bad08..4e93115963 100644 --- a/include/image-commands.mk +++ b/include/image-commands.mk @@ -56,6 +56,18 @@ define Build/cameo-factory mv $@.new $@ endef +# blow up binary to given size and put a given string at its end: +# cameo-factory +define Build/cameo-factory + factory_stamp=$(word 2,$(1)); \ + ((reduced_size=$(subst k,*1024,$(word 1,$(1)))-$${#factory_stamp})); \ + ( \ + dd if=$@ bs=$$reduced_size conv=sync; \ + echo -n $$factory_stamp; \ + ) > $@.new && \ + mv $@.new $@ +endef + define Build/eva-image $(STAGING_DIR_HOST)/bin/lzma2eva $(KERNEL_LOADADDR) $(KERNEL_LOADADDR) $@ $@.new mv $@.new $@ diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 43b537835c..9363440438 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -63,6 +63,16 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0:lan" "1:lan" "2:lan" "3:lan" "5@eth0" ;; + dlink,dir-825-c1|\ + dlink,dir-835-a1|\ + iodata,etg3-r|\ + iodata,wn-ac1167dgr|\ + iodata,wn-ac1600dgr2|\ + iodata,wn-ag300dgr|\ + pcs,cr5000) + ucidef_add_switch "switch0" \ + "0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" + ;; elecom,wrc-300ghbk2-i) ucidef_add_switch "switch0" \ "0@eth0" "2:lan:4" "3:lan:3" "4:lan:2" "5:lan:1" "1:wan" @@ -79,14 +89,6 @@ ath79_setup_interfaces() glinet,gl-x750) ucidef_set_interfaces_lan_wan "eth1" "eth0" ;; - iodata,etg3-r|\ - iodata,wn-ac1167dgr|\ - iodata,wn-ac1600dgr2|\ - iodata,wn-ag300dgr|\ - pcs,cr5000) - ucidef_add_switch "switch0" \ - "0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" - ;; netgear,wndr3700|\ netgear,wndr3700v2|\ netgear,wndr3800) @@ -217,6 +219,11 @@ ath79_setup_macs() lan_mac=$(mtd_get_mac_text "caldata" 65440) wan_mac=$(mtd_get_mac_text "caldata" 65460) ;; + dlink,dir-825-c1|\ + dlink,dir-835-a1) + lan_mac=$(mtd_get_mac_text "mac" 4) + wan_mac=$(mtd_get_mac_text "mac" 24) + ;; elecom,wrc-300ghbk2-i) wan_mac=$(macaddr_add "$(mtd_get_mac_binary ART 4098)" -2) ;; diff --git a/target/linux/ath79/base-files/etc/board.d/03_gpio_switches b/target/linux/ath79/base-files/etc/board.d/03_gpio_switches index 4af9845b65..4f08fab525 100755 --- a/target/linux/ath79/base-files/etc/board.d/03_gpio_switches +++ b/target/linux/ath79/base-files/etc/board.d/03_gpio_switches @@ -10,6 +10,10 @@ board_config_update board=$(board_name) case "$board" in +dlink,dir-825-c1|\ +dlink,dir-835-a1) + ucidef_add_gpio_switch "wan_led_auto" "WAN LED Auto" "20" "0" + ;; ubnt,nanostation-ac) ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "3" ;; diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index 68943b4eb0..bf61ecf5dd 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -100,6 +100,11 @@ case "$FIRMWARE" in avm,fritz4020) ath9k_eeprom_extract_reverse "urlader" 5441 1088 ;; + dlink,dir-825-c1|\ + dlink,dir-835-a1) + ath9k_eeprom_extract "art" 4096 1088 + ath9k_patch_fw_mac_crc $(mtd_get_mac_text "mac" 4) 2 + ;; iodata,wn-ac1167dgr|\ iodata,wn-ac1600dgr2|\ iodata,wn-ag300dgr) @@ -125,6 +130,11 @@ case "$FIRMWARE" in buffalo,wzr-hp-g450h) ath9k_eeprom_extract "ART" 4096 1088 ;; + dlink,dir-825-c1|\ + dlink,dir-835-a1) + ath9k_eeprom_extract "art" 20480 1088 + ath9k_patch_fw_mac_crc $(macaddr_add $(mtd_get_mac_text "mac" 24) 1) 2 + ;; ocedo,raccoon|\ tplink,tl-wdr3600|\ tplink,tl-wdr4300|\ diff --git a/target/linux/ath79/dts/ar9344_dlink_dir-825-c1.dts b/target/linux/ath79/dts/ar9344_dlink_dir-825-c1.dts new file mode 100644 index 0000000000..89603aaff6 --- /dev/null +++ b/target/linux/ath79/dts/ar9344_dlink_dir-825-c1.dts @@ -0,0 +1,79 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "ar9344_dlink_dir-8x5.dtsi" + +/ { + model = "D-LINK DIR-825 C1"; + compatible = "dlink,dir-825-c1", "qca,ar9344"; + + aliases { + led-boot = &orange_power; + led-failsafe = &orange_power; + led-running = &blue_power; + led-upgrade = &orange_power; + serial0 = &uart; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&enable_gpio_11>; + + blue_power: blue_power { + label = "d-link:blue:power"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + }; + + blue_usb { + label = "d-link:blue:usb"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + linux,default-trigger = "usbport"; + trigger-sources = <&hub_port1>; + }; + + blue_wan { + label = "d-link:blue:wan"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + }; + + blue_wlan2g { + label = "d-link:blue:wlan2g"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + blue_wps { + label = "d-link:blue:wps"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + orange_power: orange_power { + label = "d-link:orange:power"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + orange_wan { + label = "d-link:orange:wan"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + }; + }; + + leds-ath9k { + compatible = "gpio-leds"; + + blue_wlan5g { + label = "d-link:blue:wlan5g"; + gpios = <&ath9k 0 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + }; +}; + +&pinmux { + enable_gpio_11: pinmux_enable_gpio_11 { + pinctrl-single,bits = <0x8 0x0 0xff000000>; + }; +}; + diff --git a/target/linux/ath79/dts/ar9344_dlink_dir-835-a1.dts b/target/linux/ath79/dts/ar9344_dlink_dir-835-a1.dts new file mode 100644 index 0000000000..4f0c1e58ee --- /dev/null +++ b/target/linux/ath79/dts/ar9344_dlink_dir-835-a1.dts @@ -0,0 +1,47 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "ar9344_dlink_dir-8x5.dtsi" + +/ { + model = "D-LINK DIR-835 A1"; + compatible = "dlink,dir-835-a1", "qca,ar9344"; + + aliases { + led-boot = &orange_power; + led-failsafe = &orange_power; + led-running = &green_power; + led-upgrade = &orange_power; + serial0 = &uart; + }; + + leds { + compatible = "gpio-leds"; + + green_power: green_power { + label = "d-link:green:power"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + }; + + green_wan { + label = "d-link:green:wan"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + }; + + green_wps { + label = "d-link:green:wps"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + orange_power: orange_power { + label = "d-link:orange:power"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + orange_wan { + label = "d-link:orange:wan"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + }; + }; +}; + diff --git a/target/linux/ath79/dts/ar9344_dlink_dir-8x5.dtsi b/target/linux/ath79/dts/ar9344_dlink_dir-8x5.dtsi new file mode 100644 index 0000000000..b49d3458fe --- /dev/null +++ b/target/linux/ath79/dts/ar9344_dlink_dir-8x5.dtsi @@ -0,0 +1,151 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "ar9344.dtsi" + +/ { + chosen { + bootargs = "console=ttyS0,115200"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + linux,code = ; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + wps { + linux,code = ; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; +}; + +ð0 { + status = "okay"; + + /* default for ar934x, except for 1000M */ + pll-data = <0x06000000 0x00000101 0x00001616>; + + phy-mode = "rgmii"; + phy-handle = <&phy0>; +}; + +&mdio0 { + status = "okay"; + + phy-mask = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + qca,ar8327-initvals = < + /* GPL code drop (bsp.h & athrs17_phy.c) */ + 0x10 0xc1000000 /* PWS_REG_VALUE */ + 0x04 0x07600000 /* PORT0 PAD Mode */ + 0x0c 0x01000000 /* PORT6 PAD Mode */ + 0x7c 0x0000007e /* PORT0_STATUS */ + 0x94 0x0000007e /* PORT6_STATUS */ + >; + }; +}; + +&pcie { + status = "okay"; + + ath9k: wifi@0,0 { + compatible = "pci168c,0030"; + reg = <0x0000 0 0 0 0>; + qca,no-eeprom; + gpio-controller; + #gpio-cells = <2>; + }; +}; + +&ref { + clock-frequency = <40000000>; +}; + +&spi { + status = "okay"; + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x000000 0x010000>; + read-only; + }; + + partition@10000 { + label = "nvram"; + reg = <0x010000 0x010000>; + read-only; + }; + + partition@20000 { + label = "firmware"; + reg = <0x020000 0xF90000>; + compatible = "denx,uimage"; + }; + + partition@fb0000 { + label = "lang"; + reg = <0xfb0000 0x030000>; + read-only; + }; + + partition@fe0000 { + label = "mac"; + reg = <0xfe0000 0x010000>; + read-only; + }; + + partition@ff0000 { + label = "art"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +&uart { + status = "okay"; +}; + +&usb { + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + hub_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&wmac { + status = "okay"; + qca,no-eeprom; +}; + diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index df91c91826..cf71cb30b8 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -138,6 +138,32 @@ define Device/dlink_dir-825-b1 endef TARGET_DEVICES += dlink_dir-825-b1 +define Device/dlink_dir-825-c1 + ATH_SOC := ar9344 + DEVICE_TITLE := D-LINK DIR-825 C1 + DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport kmod-leds-reset kmod-owl-loader + SUPPORTED_DEVICES += dir-825-c1 + IMAGE_SIZE := 15936k + IMAGES := factory.bin sysupgrade.bin + IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs + IMAGE/factory.bin := $$(IMAGE/default) | cameo-factory $$$$(IMAGE_SIZE) 00DB120AR9344-RT-101214-00 | check-size $$$$(IMAGE_SIZE) + IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | check-size $$$$(IMAGE_SIZE) +endef +TARGET_DEVICES += dlink_dir-825-c1 + +define Device/dlink_dir-835-a1 + ATH_SOC := ar9344 + DEVICE_TITLE := D-LINK DIR-835 A1 + DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-leds-reset kmod-owl-loader + SUPPORTED_DEVICES += dir-835-a1 + IMAGE_SIZE := 15936k + IMAGES := factory.bin sysupgrade.bin + IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs + IMAGE/factory.bin := $$(IMAGE/default) | cameo-factory $$$$(IMAGE_SIZE) 00DB120AR9344-RT-101214-00 | check-size $$$$(IMAGE_SIZE) + IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | check-size $$$$(IMAGE_SIZE) +endef +TARGET_DEVICES += dlink_dir-835-a1 + define Device/elecom_wrc-300ghbk2-i ATH_SOC := qca9563 DEVICE_TITLE := ELECOM WRC-300GHBK2-I