From: David Bauer <mail@david-bauer.net>
Date: Tue, 1 Jan 2019 18:17:22 +0000 (+0100)
Subject: ath79: add support for devolo WiFi pro 1750i
X-Git-Tag: v19.07.0-rc1~1665
X-Git-Url: http://git.openwrt.org/?p=openwrt%2Fopenwrt.git;a=commitdiff_plain;h=8d68be8057d6c689025cc236d20b96b77a6ccf30

ath79: add support for devolo WiFi pro 1750i

Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
---

diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index 97d1390106..0b1a5f39a1 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -11,6 +11,7 @@ ath79_setup_interfaces()
 	case "$board" in
 	avm,fritz300e|\
 	devolo,dvl1750c|\
+	devolo,dvl1750i|\
 	ocedo,koala|\
 	ocedo,raccoon|\
 	pcs,cap324|\
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index faee781970..9fc0f80569 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -88,7 +88,8 @@ case "$FIRMWARE" in
 "ath10k/cal-pci-0000:00:00.0.bin")
 	case $board in
 	devolo,dvl1200e|\
-	devolo,dvl1750c)
+	devolo,dvl1750c|\
+	devolo,dvl1750i)
 		ath10kcal_extract "art" 20480 2116
 		ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary art 0) -1)
 		;;
diff --git a/target/linux/ath79/dts/qca9558_devolo_dvl1750i.dts b/target/linux/ath79/dts/qca9558_devolo_dvl1750i.dts
new file mode 100644
index 0000000000..bd3702eb36
--- /dev/null
+++ b/target/linux/ath79/dts/qca9558_devolo_dvl1750i.dts
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca9558_devolo_dvl1xxx.dtsi"
+
+/ {
+	compatible = "devolo,dvl1750i", "qca,qca9557";
+	model = "devolo WiFi pro 1750i";
+
+	aliases {
+		led-boot = &status_blue;
+		led-failsafe = &status_red;
+		led-running = &status_blue;
+		led-upgrade = &status_red;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		status_blue: status_blue {
+			label = "dvl1750i:blue:status";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		status_red: status_red {
+			label = "dvl1750i:red:status";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	beeper {
+		compatible = "gpio-beeper";
+		gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&eth0 {
+	pll-data = <0xbe000000 0x80000101 0x80001313>;
+};
+
+&gmac_config {
+	rxdv-delay = <3>;
+	rxd-delay = <3>;
+	txen-delay = <3>;
+	txd-delay = <3>;
+	rgmii-enabled = <1>;
+};
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 858c1662cc..438a842182 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -178,6 +178,14 @@ define Device/devolo_dvl1750c
 endef
 TARGET_DEVICES += devolo_dvl1750c
 
+define Device/devolo_dvl1750i
+  ATH_SOC := qca9558
+  DEVICE_TITLE := devolo WiFi pro 1750i
+  DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
+  IMAGE_SIZE := 15936k
+endef
+TARGET_DEVICES += devolo_dvl1750i
+
 define Device/dlink_dir-825-b1
   ATH_SOC := ar7161
   DEVICE_TITLE := D-LINK DIR-825 B1